CDE ESR4R7M1C000B Type esr surface mount polymer aluminum electrolytic capacitors. Datasheet

TYPE ESR SURFACE MOUNT POLYMER ALUMINUM
ELECTROLYTIC CAPACITORS.
Type ESR SMT capacitors are polarized, aluminum
capacitors which use a highly conductive solid
polymer as the electrolyte.
They have reliability advantages over both
aluminum and solid tantalum electrolytic capacitors.
Unlike aluminum capacitors, there is no liquid
electrolyte to evaporate and cause failure.
Unlike solid tantalum, which can fail short and burn, type ESR capacitors in normal operation fail
benignly as gradual open circuits after 25 to 50 years of operation.
The equivalent series resistance of these capacitors is much lower than for solid tantalum
capacitors, thus you get much higher ripple current handling capability.
NOTE: Type ESR capacitors are not recommended for new design, and therefore, may be subject to
larger than expected minimum order quantities. CDE capacitor Types ESRD, ESRE, and ESRL are
recommended for new design, and can be used as replacements to upgrade existing designs that
employ Type ESR capacitors. However, the ESRD, ESRE, and ESRL footprint is not compatible with
the Type ESR footprint.
Specifications:
Operating Temperature Range:
-55°C to +105°C at 100% rated Voltage.
Surge Voltage:
125% of the rated working Vdc
Capacitance Range:
4.7uF to 82 uF
Capacitance Tolerance:
±20% at 120Hz and +20°C.
DC Leakage Current (DCL):
After a 2 minute application of the rated voltage at
+ 20°C the DCL is;
4V: < 0.06CV
6.3V - 16V: < 0.04CV or 3µA (whichever is
Moisture Resistance:
After 500 hours storage at +60°C and 90 to 95%
R.H. without load, capacitor will meet the
following limits:
Capacitance change from the initial value shall
not exceed;
+60%/-20% for 4.0 Vdc ratings,
+50%/-20% for 6.3 Vdc ratings,
+40%/-20% for all other ratings.
DCL shall meet the initial specification.
D.F. shall meet the initial specification. The ratings
of 68µf/4V, 82µf/4V, 68µf/6.3V, 47µf/8V, and
33µf/12.5V shall not exceed twice the initial
specification.
greater)
Dissipations Factor (DF):
The ratio of the capacitor's equivalent series
resistance to its reactance. It's no more than 0.06
at 120Hz and +20°C.
Resistance to Soldering Heat:
Capacitors will withstand 30 seconds at +240 ºC in
a solder-reflow oven.
Life Test:
Apply rated dc working voltage at 105°C for
1,000 hours and then stabilize to +20°C.
Capacitors will meet the following limits:
Capacitance change shall not exceed ± 10% of
the initial measured value.
D.F. and D.C.L. shall not exceed the initial
specified value.
Shelf Life Test:
Shelf life is typically 5 to 10 years. Accelerated
test:after 500 hours at 105°C, capacitors will meet
the following limits after stabilization at 20°C:
Capacitance change shall not exceed ± 10% of
the initial measured value.
D.F. and D.C.L. shall not exceed the initial
specified value.
Dimensions
Available Ratings:
Capacitance
(µF)
Catalog Number
Reel
Quantity
Catalog Number
For Bulk Quantitites
Less Than Full Reel Qty.
Maximum Ripple
AMPS rms
(at 100 kHz, +100°C)
4 Vdc
82.00
ESR820M0G1316
2,200
ESR820M0G000B
1.6
10.00
ESR100M0J1516
3,000
ESR100M0J000B
1.0
22.00
ESR220M0J1516
3,000
ESR220M0J000B
1.3
33.00
ESR330M0J1516
3,000
ESR330M0J000B
1.6
47.00
ESR470M0J1516
3,000
ESR470M0J000B
1.6
68.00
ESR680M0J1316
2,200
ESR680M0J000B
1.6
22.00
ESR220M0K1516
3,000
ESR220M0K000B
1.6
33.00
ESR330M0K1516
3,000
ESR330M0K000B
1.6
47.00
ESR470M0K1316
2,200
ESR470M0K000B
1.6
10.00
ESR100M1B1516
3,000
ESR100M1B000B
1.0
22.00
ESR220M1B1516
3,000
ESR220M1B000B
1.6
33.00
ESR330M1B1316
2,200
ESR330M1B000B
1.6
4.70
ESR4R7M1C1516
3,000
ESR4R7M1C000B
1.0
6.80
ESR6R8M1C1516
3,000
ESR6R8M1C000B
1.0
10.00
ESR100M1C1516
3,000
ESR100M1C000B
1.3
6.3 Vdc
8 Vdc
12.5 Vdc
16 Vdc
All product specifications, and all purchases of products from Cornell-Dubilier, are subject to its Terms and Conditions.
Tel# 508-996-8564
Fax# 508-996-3830
Similar pages