MPS EV2104DJ-00A 1.7mhz, 600ma synchronous step-down converter Datasheet

TM
MP2104
1.7MHz, 600mA Synchronous
Step-Down Converter
The Future of Analog IC Technology
TM
DESCRIPTION
FEATURES
The MP2104 is a 1.7MHz constant frequency,
current mode, PWM step-down converter. The
device integrates a main switch and a
synchronous rectifier for high efficiency without an
external Schottky diode. It is ideal for powering
portable equipment that runs from a single cell
Lithium-Ion (Li+) battery. The MP2104 can supply
600mA of load current from a 2.5V to 6V input
voltage. The output voltage for the MP2104DJ
can be regulated as low as 0.6V, while the output
voltages
of
the
MP2104DJ-1.5
and
MP2104DJ-1.8 are fixed at 1.5V and 1.8V,
respectively. The MP2104 can also run at 100%
duty cycle for low dropout applications.
•
•
•
•
•
•
•
•
•
•
•
•
The MP2104 is available in a low profile (1mm)
5-pin, TSOT package.
•
•
•
•
•
•
ORDERING INFORMATION
Part Number
MP2104DJ-1.5
MP2104DJ-1.8
MP2104DJ
Output Voltage
VOUT = 1.5V
VOUT = 1.8V
VOUT = 0.6V to 6V
EVALUATION BOARD REFERENCE
Board Number
Dimensions
EV2104DJ-00A
2.0”X x 2.0”Y x 0.5”Z
High Efficiency: Up to 95%
1.7MHz Constant Switching Frequency
600mA Available Load Current
2.5V to 6V Input Voltage Range
Output Voltage as Low as 0.6V
100% Duty Cycle in Dropout
Current Mode Control
Short Circuit Protection
Thermal Fault Protection
<0.1µA Shutdown Current
1.5V and 1.8V Fixed Output Versions
Space Saving 5-Pin TSOT23 Package
APPLICATIONS
Cellular and Smart Phones
Microprocessors and DSP Core Supplies
PDAs
MP3 Players
Digital Still and Video Cameras
Portable Instruments
“MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic
Power Systems, Inc.
TYPICAL APPLICATION
Efficiency vs
Load Current
100
4
IN
SW
3
MP2104DJ-1.8
OFF ON
1
EN
GND
OUT
5
2
90
VIN = 3.3V
80
EFFICIENCY (%)
INPUT
2.5V - 6V
OUTPUT
1.8V
600mA
VIN = 4.2V
70
60
50
40
30
20
MP2104_TAC_S01
10
0
10
100
LOAD CURRENT (mA)
1000
MP2104-EC01
MP2104 Rev. 1.3
10/4/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
1
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
PACKAGE REFERENCE
TOP VIEW
GND
2
SW
3
5
FB
4
IN
EN
1
GND
2
SW
3
MP2104_PD01-TSOT23-5
OUT
4
IN
MP2104_PD02-TSOT23-5
Part Number*
Package
Temperature
MP2104DJ
TSOT23-5
–40°C to +85°C
*
5
MARKING
1
C2YW
EN
TOP VIEW
For Tape & Reel, add suffix –Z (eg. MP2104DJ–Z)
For Lead Free, add suffix –LF (eg. MP2104DJ–LF–Z)
Part Number**
Package
Marking
Temp
MP2104DJ-1.5
TSOT23-5
D7YW
MP2104DJ-1.8
TSOT23-5
D8YW
–40°C to
+85°C
** For Tape & Reel, add suffix –Z (eg. MP2104DJ-1.5–Z)
For Lead Free, add suffix –LF (eg. MP2104DJ-1.5–LF–Z)
ABSOLUTE MAXIMUM RATINGS (1)
Recommended Operating Conditions
VIN to GND ..................................–0.3V to +6.5V
VSW to GND........................... –0.3V to VIN +0.3V
VFB, VEN to GND ..........................–0.3V to +6.5V
SW Peak Current ........................................ 1.4A
Junction Temperature .............................+150°C
(2)
Lead Temperature ..............................+260°C
Storage Temperature ............. –65°C to +150°C
Thermal Resistance
(3)
Supply Voltage VIN ............................. 2.5V to 6V
Output Voltage VOUT .......................... 0.6V to 6V
Operating Temperature .............–40°C to +85°C
(4)
θJA
θJC
TSOT23-5.............................. 220 .... 110.. °C/W
Notes:
1) Exceeding these ratings may damage the device.
2) For recommended IR reflow temperature information, refer to
MPS document MP2104_IRRTP.
3) The device is not guaranteed to function outside of its
operating conditions.
4) Measured on approximately 1” square of 1 oz copper.
ELECTRICAL CHARACTERISTICS (5)
VIN = VEN = 3.6V, TA = +25°C, unless otherwise noted.
Parameter
Supply Current
Shutdown Current
IN Under Voltage Lockout
Threshold
IN Under Voltage Lockout
Hysteresis
Regulated FB Voltage
FB Input Bias Current
MP2104 Rev. 1.3
10/4/2005
Symbol Condition
VEN = VIN, VFB = 0.65V
VEN = 0V, VIN = 6V
Min
Typ
400
0.01
Max
600
1
Units
µA
µA
Rising Edge
2.10
2.27
2.45
V
55
TA = +25°C, MP2104DJ
–40°C ≤ TA ≤ +85°C
VFB = 0.65V, MP2104DJ
0.588
0.582
–50
0.600
0.600
0.5
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
mV
0.612
0.618
+50
V
nA
2
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
ELECTRICAL CHARACTERISTICS (continued) (5)
VIN = VEN = 3.6V, TA = +25°C, unless otherwise noted.
Parameter
Regulated Output Voltage
PFET On Resistance
NFET On Resistance
SW Leakage Current
PFET Current Limit
Oscillator Frequency
Thermal Shutdown Trip
Threshold
EN Trip Threshold
EN Input Current
Symbol Condition
MP2104DJ-1.5
IOUT = 50mA
–40°C ≤ TA ≤ +85°C
MP2104DJ-1.8
IOUT = 50mA
–40°C ≤ TA ≤ +85°C
ISW = 100mA
ISW = –100mA
VEN = 0V, VIN = 6V
VSW = 0V or 6V
Duty Cycle = 100%,
Current Pulse Width < 1ms
Min
Typ
Max
1.455
1.500
1.545
V
1.746
1.800
1.854
0.44
0.29
–1
Ω
Ω
+1
µA
0.7
1.0
1.35
A
1.26
1.70
2.08
MHz
°C
145
–40°C ≤ TA ≤ +85°C
VEN = 0V to 6V
Units
0.3
–1
0.96
1.5
+1
V
µA
Notes:
5) 100% production test at +25°C. Typical and temperature specifications are guaranteed by design and characterization.
MP2104 Rev. 1.3
10/4/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
3
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 3.3V, VOUT = 1.8V, L1 = 10µH, C1 = 4.7µF, C3 = 10µF, TA = +25°C, unless otherwise noted.
Efficiency vs
Load Current
100
90
90
VIN = 3.3V
EFFICIENCY (%)
VIN = 4.2V
60
50
40
30
1.83
VIN = 4.2V
70
60
50
40
30
1.77
1.75
1.73
1.71
1.69
10
10
1.67
0
0
1.65
100
LOAD CURRENT (mA)
1000
10
100
LOAD CURRENT (mA)
90
90
80
80
EFFICIENCY (%)
100
60
50
40
30
0
10
100
LOAD CURRENT (mA)
Output Voltage vs
Supply Voltage
70
60
50
40
30
VOUT = 1.8V
VIN = 4.2V
10
0
1000
10
MP2104-TPC03
100
LOAD CURRENT (mA)
PFET CURRENT LIMIT (A)
0.605
0.600
0.595
0.590
0.585
0.580
-50 -30 -10 10 30 40 70 90 110 130
TEMPERATURE (°C)
MP2104-TPC07
1.804
1.802
ILOAD = 200mA
1000
1.3
0.610
1.806
1.800
2
3
4
5
SUPPLY VOLTAGE (V)
1.2
1.1
1.0
0.9
0.8
0.7
-50 -30 -10 10 30 40 70 90 110 130
TEMPERATURE (°C)
6
MP2104-TPC06
Oscillator Frequency vs
Supply Voltage
PFET Current Limit vs
Temperature
0.620
0.615
1.808
MP2104-TPC04
Regulated FB Voltage vs
Temperature
MP2104 Rev. 1.3
10/4/2005
MP2104-TPC05
1.810
20
VOUT = 1.8V
VIN = 3.3V
10
0 100 200 300 400 500 600 700 800 900
LOAD CURRENT (mA)
Efficiency vs
Load Current
70
VIN = 3.3V
MP2104-TPC02
100
20
1000
OUTPUT VOLTAGE (V)
10
Efficiency vs
Load Current
EFFICIENCY (%)
1.79
20
MP2104-TPC01
REGULATED FB VOLTAGE (V)
1.81
20
OSCILLATOR FREQUENCY (MHz)
EFFICIENCY (%)
80
70
1.85
VIN = 3.3V
OUTPUT VOLTAGE (V)
100
80
Output Voltage vs
Load Current
Efficiency vs
Load Current
2.05
1.95
1.85
1.75
1.65
1.55
1.45
1.35
1.25
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
MP2104-TPC08
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
MP2104-TPC09
4
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = 3.3V, VOUT = 1.8V, L1 = 10µH, C1 = 4.7µF, C3 = 10µF, TA = +25°C, unless otherwise noted.
MP2104 Rev. 1.3
10/4/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
5
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
PIN FUNCTIONS
Pin # Name Description
1
2
3
4
5
5
Regulator Enable Control Input. Drive EN above 1.5V to turn on the MP2104. Drive EN below
0.3V to turn it off (shutdown current < 0.1µA).
GND Ground.
SW Power Switch Output. Inductor connection to drains of the internal PFET and NFET switches.
IN
Supply Input. Bypass to GND with a 2.2µF or greater ceramic capacitor.
Feedback Input (MP2104DJ). Connect FB to the center point of the external resistor divider. The
FB
feedback threshold voltage is 0.6V.
Output Voltage Sense Input (MP2104DJ-1.5 and MP2104DJ-1.8). An internal resistor divider is
OUT
connected to this pin to set the proper output voltage.
EN
OPERATION
The MP2104 is a constant frequency current
mode PWM step-down converter. The MP2104
is optimized for low voltage, Li-Ion battery
powered applications where high efficiency and
small size are critical. The MP2104 uses an
external resistor divider to set the output
voltage from 0.6V to 6V. The device integrates
both a main switch and a synchronous rectifier,
which provides high efficiency and eliminates
an external Schottky diode. The MP2104 can
achieve 100% duty cycle. The duty cycle D of a
step-down converter is defined as:
D = TON × fOSC × 100% ≈
VOUT
× 100%
VIN
Where TON is the main switch on time, fOSC is
the oscillator frequency (1.7MHz), VOUT is the
output voltage and VIN is the input voltage.
IN
EN
ICS
0.6V
+
FB
+
IAMP
10X
-CURRENT
SENSE
AMP
BIAS
&
VOLTAGE
REFERENCE
SLOPE COMP
FEEDBACK
ERROR EAMP
AMP
--
CC
17pF
EAO
+
+ PWMCMP
PWM
DH
MAIN
SWITCH
(PCH)
--
1.7MHz
OSCILLATOR
OSC
PWM
CONTROL
LOGIC
SW
SYNCHRONOUS
RECTIFIER
(NCH)
DL
GND
MP2104_BD01
Figure 1—Functional Block Diagram (MP2104)
MP2104 Rev. 1.3
10/4/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
6
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
IN
EN
ICS
0.6V
SLOPE COMP
+
OUT
+
IAMP
10X
-CURRENT
SENSE
AMP
BIAS
&
VOLTAGE
REFERENCE
FEEDBACK
ERROR EAMP
AMP
--
CC
17pF
EAO
+
+ PWMCMP
PWM
DH
MAIN
SWITCH
(PCH)
--
1.7MHz
OSCILLATOR
OSC
PWM
CONTROL
LOGIC
SW
SYNCHRONOUS
RECTIFIER
(NCH)
DL
GND
MP2104_BD01
Figure 2—Functional Block Diagram (MP2104DJ-1.5 / MP2104DJ-1.8)
Current Mode PWM Control
Slope compensated current mode PWM control
provides stable switching and cycle-by-cycle
current limit for superior load and line response
and protection of the internal main switch and
synchronous rectifier. The MP2104 switches at a
constant frequency (1.7MHz) and regulates the
output voltage. During each cycle the PWM
comparator modulates the power transferred to the
load by changing the inductor peak current based
on the feedback error voltage. During normal
operation, the main switch is turned on for a certain
time to ramp the inductor current at each rising
edge of the internal oscillator, and switched off
when the peak inductor current is above the error
voltage. When the main switch is off, the
synchronous rectifier will be turned on immediately
and stay on until either the next cycle starts.
Dropout Operation
The MP2104 allows the main switch to remain on
for more than one switching cycle and increases
the duty cycle while the input voltage is dropping
close to the output voltage. When the duty cycle
reaches 100%, the main switch is held on
continuously to deliver current to the output up to
MP2104 Rev. 1.3
10/4/2005
the PFET current limit. The output voltage then is
the input voltage minus the voltage drop across
the main switch and the inductor.
Short Circuit Protection
The MP2104 has short circuit protection. When
the output is shorted to ground, the oscillator
frequency is reduced to prevent the inductor
current from increasing beyond the PFET current
limit. The PFET current limit is also reduced to
lower the short circuit current. The frequency and
current limit will return to the normal values once
the short circuit condition is removed and the
feedback voltage reaches 0.6V.
Maximum Load current
The MP2104 can operate down to 2.5V input
voltage, however the maximum load current
decreases at lower input due to large IR drop on
the main switch and synchronous rectifier. The
slope compensation signal reduces the peak
inductor current as a function of the duty cycle to
prevent sub-harmonic oscillations at duty cycles
greater than 50%. Conversely the current limit
increases as the duty cycle decreases.
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
7
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
APPLICATION INFORMATION
Output Voltage Setting (MP2104DJ)
The external resistor divider sets the output
voltage (see Figure 3). The feedback resistor R1
also sets the feedback loop bandwidth with the
internal compensation capacitor (see Figure 1).
Choose R1 around 300kΩ for optimal transient
response. R2 is then given by:
R2 =
R1
VOUT
−1
0 .6 V
Inductor Selection
A 1µH to 10µH inductor with DC current rating
at least 25% higher than the maximum load
current is recommended for most applications.
For best efficiency, the inductor DC resistance
shall be <200mΩ. See Table 2 for
recommended inductors and manufacturers.
For most designs, the inductance value can be
derived from the following equation:
L=
Table 1—Resistor Selection vs. Output
Voltage Setting
VOUT
R1
R2
1.2V
300kΩ (1%)
300kΩ (1%)
1.5V
300kΩ (1%)
200kΩ (1%)
1.8V
300kΩ (1%)
150kΩ (1%)
2.5V
300kΩ (1%)
95.3kΩ (1%)
VOUT × (VIN − VOUT )
VIN × ∆IL × fOSC
Where ∆IL is the inductor ripple current. Choose
inductor ripple current approximately 30% of the
maximum load current, 600mA.
The maximum inductor peak current is:
IL(MAX ) = ILOAD +
∆IL
2
Under light load conditions below 100mA, larger
inductance is recommended for improved
efficiency. Table 3 lists inductors recommended
for this purpose.
Table 2—Suggested Surface Mount Inductors
Manufacturer
Part Number
Inductance (µH)
Max DCR (Ω)
Saturation
Current (A)
Dimensions
LxWxH (mm3)
Coilcraft
Toko
Sumida
Taiyo Yuden
LP1704-222M
D312C
CDRH3D16
LBC2518
2.2
2.2
2.2
2.2
0.07
0.14
0.072
0.13
1.7
1.0
1.2
0.6
6.5x5.3x2
3.6x3.6x1
4x4x1.8
2.5x1.8x1.8
Table 3—Inductors for Improved Efficiency at 25mA, 50mA, under 100mA Load.
Manufacturer
Part Number
Inductance (µH)
Max DCR (Ω)
Saturation
Current (A)
IRMS (A)
Coilcraft
Murata
Sumida
Sumida
Sumida
DO1605T-103MX
LQH4C100K04
CMD4D06-100
CR32-100
CR54-100
10
10
10
10
10
0.3
0.2
0.3
0.2
0.1
1.0
1.2
0.7
1.0
1.2
0.9
0.8
0.5
0.7
1.4
MP2104 Rev. 1.3
10/4/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
8
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
Input Capacitor Selection
The input capacitor reduces the surge current
drawn from the input and switching noise from
the device. The input capacitor impedance at
the switching frequency shall be less than input
source impedance to prevent high frequency
switching current passing to the input. Ceramic
capacitors with X5R or X7R dielectrics are
highly recommended because of their low ESR
and small temperature coefficients. For most
applications, a 4.7µF capacitor is sufficient.
PC Board Layout
The high current paths (GND, IN and SW)
should be placed very close to the device with
short, direct and wide traces. Input capacitor C1
needs to be as close as possible to the IN and
GND pins. The external feedback resistors shall
be placed next to the FB pin. Keep the
switching node SW short and away from the
feedback network. Figure 3 illustrates an
example of PCB layout and signal routing.
Output Capacitor Selection
The output capacitor keeps output voltage
ripple small and ensures regulation loop stable.
The output capacitor impedance shall be low at
the switching frequency. Ceramic capacitors
with X5R or X7R dielectrics are recommended.
The output ripple ∆VOUT is approximately:
∆VOUT ≤
⎞
VOUT × (VIN − VOUT ) ⎛
1
⎟
× ⎜⎜ ESR +
⎟
VIN × fOSC × L
8
×
f
×
C
3
OSC
⎠
⎝
Figure 3—MP2104 Suggested Layout
For the fixed output versions (MP2104DJ-1.5
and MP2104-1.8), R1 is shorted and R2 is
open.
Efficiency vs
Load Current
100
IN
SW
3
MP2104
1
OFF ON
EN
GND
FB
OUTPUT
1.8V
600mA
5
2
90
VIN = 3.3V
80
EFFICIENCY (%)
4
INPUT
2.5V - 6V
VIN = 4.2V
70
60
50
40
30
20
10
MP2104_F04
0
10
100
LOAD CURRENT (mA)
1000
MP2104-EC02
Figure 4—VIN = 2.5V to 6V, VOUT = 1.8V, ILOAD = 600mA Step-Down Circuit
(L = 10µH for Higher Light-Load Efficiency)
NOTICE: MPS believes the information in this document to be accurate and reliable. However, it is subject to change without
notice. Contact MPS for current specifications. MPS encourages users of its products to ensure that third party Intellectual
Property rights are not infringed upon when integrating MPS products into any application. MPS cannot assume any legal
responsibility for any said applications.
MP2104 Rev. 1.0
10/4/05
© 2004 MPS, Inc.
Monolithic Power Systems, Inc.
983 University Avenue, Building A, Los Gatos, CA 95032 USA
Tel: 408-357-6600 ♦ Fax: 408-357-6601 ♦ www.MonolithicPower.com
9
TM
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
PACKAGE INFORMATION
TSOT23-5
2.90 BSC
3
0.950
TYP
.
10°TYP.
(2 plcs)
C
L
2.80 BSC
1.60 BSC
3
0.950
TYP
.
+ 4°
- 0°
0°
0.25 BSC.
±0.10
Gauge Plane
C
L
0.87±0.03
1.00
Max.
0.300(Min)
0.500(Max)
(5
PLCS)
0.400
0.00-0.10
SEATING PLANE
0.127 TYP.
10° TYP.
(2 plcs)
NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
MP2104 Rev. 1.3
10/4/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
10
Similar pages