AWL6254 2.4 GHz 802.11b/g/n WLAN PA, LNA, and RF Switch Data Sheet - Rev 2.0 FEATURES • 3.3 % EVM @ POUT = +16 dBm with IEEE 802.11g 64 QAM OFDM at 54 Mbps • 75 mA Transmit Path Current Consumption at POUT = +16 dBm • SP3T RF Switch to Enable Bluetooth Path • Single +3.6 V Supply • Transmit Path Linear Power Gain of 28 dB • Temperature-Compensated Linear Power Detector with Positive Slope • Receive Path In-Band Gain of 13 dB • Receive Path Noise Figure of 2.3 dB • 3 mm x 3 mm x 0.55 mm ULPCC Package AW L6 254 APPLICATIONS S35 Package 16 Pin 3 mm x 3 mm x 0.55 mm Surface Mount ULPCC • 802.11b/g WLAN in Cell Phone Designs • 802.11n in WLAN MIMO Systems • 2.4 GHz Cordless Phone Handsets/Basestations 02/2008 Rx RFOUT VCC Output Match Antenna WLAN Rx Enable Control Logic BLUETOOTH Enable WLAN Tx Enable Tx RFIN Input Match Output Match Bias Network Power Detector DET_OUT The positive slope power detector is temperaturecompensated on the chip, enabling a single-ended output voltage with excellent accuracy over a wide range of operating temperatures. The AWL6254 is biased by a single +3.6 V supply and consumes ultralow current in the OFF mode. Bias Network VCC The antenna port is switched between WLAN transmit, WLAN receive, and Bluetooth paths with a low-loss single-pole triple-throw RF switch. The transmit path PA exhibits unparalleled linearity for both IEEE 802.11b/g/n WLAN systems under the toughest signal configurations within these standards. The WLAN receive path from the antenna port to receiver output port provides a low noise, high-gain path to the system receiver chain. BLUETOOTH The AWL6254 is manufactured using advanced InGaP HBT technology that offers state-of-the-art reliability, temperature stability and ruggedness. It is provided in a 3 mm x 3 mm x 0.55 mm ULPCC package optimized for a 50 system. GND The ANADIGICS AWL6254 is a high performance InGaP HBT power amplifier, low-noise amplifier, and RF switch integrated on a single IC. It is particularly applicable to cell phone designs that integrate 802.11b/g WLAN in the 2.4 - 2.5 GHz band. Matched to 50 on all RF ports, the part requires no additional RF matching components off-chip. GND PRODUCT DESCRIPTION Figure 1: Block Diagram and Pinout AWL6254 Table 1: Pin Description PIN 1 2 NAME DESCRIPTION BLUETOOTH Bluetooth RF Port 2 GND Ground 3 RX_RF 4 GND 5 LNA_EN 6 BT_EN Bluetooth Enable. On/Off control for the Bluetooth path 7 PA_EN Power Amplifier Enable. On/Off control for the Tx path power amplfier 8 GND Ground 9 PA_IN Power Amplfier Input 10 GND Ground 11 NC No Connection 12 VCC Power Supply. Bias for the transistors in the part 13 DET_OUT 14 GND Ground 15 ANT Antenna Port. Common connection for the PA, LNA, and Bluetooth paths 16 GND Ground Receive RF Port Ground LNA Enable. On/Off control for the Rx path low noise amplifier Power Detector Output. DC coupled power detector output. An emitter follower BJT supplies the output for this pin. Data Sheet - Rev 2.0 02/2008 AWL6254 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT COMMENTS DC Power Supply Voltage (VCC) - +5.0 V No RF Signal Applied DC Power Control Voltage (VPA_EN) - +5.0 V No RF Signal Applied DC Power Control Voltage (VLNA_EN) - +5.0 V No RF Signal Applied DC Power Control Voltage (VBT_EN) - +5.0 V No RF Signal Applied DC Current Consumption - 300 mA Tx RF Input Level (RFIN) - 0 dBm Ant RF Input Level (RFIN) - -3 dBm Bluetooth RF Input Level (RFIN) - 23 dBm Storage Case Temperature -55 +150 °C Operating Case Temperature -40 +85 °C ESD Tolerance 500 - VDC MSL Rating - MSL-2 Reflow Temperature - 260 All pins, forward and reverse voltage. Human Body Model (HBM) °C Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 2400 - 2500 MHz DC Power Supply Voltage (VCC) +3.3 +3.6 +4.2 V Control Voltage (VPA_EN, VLNA_EN, VBT_EN) +2.0 0 +3.3 - +4.2 +0.4 V Case Temperature (TC) -40 - +85 °C - 720 - k Control Pin Impedance (VPA_EN, VLNA_EN, VBT_EN) COMMENTS PA "ON" PA "SHUTDOWN" The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet - Rev 2.0 02/2008 3 AWL6254 Table 4: DC Electrical Specifications - Tx Path Continuous Wave (TC = +25 °C, VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V , VBT_EN = 0 V) PARAMETER MIN TYP MAX UNIT P1dB 20 22 - dBm Current at P1dB 140 175 210 mA Shutdown Current - 25 75 A Shutdown Mode Quiescent Current 18 26 34 mA VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V, VBT_EN = 0 V, RF = off - -48 -68 -40 -60 dBc POUT=+18 dBm (1) Input Return Loss, Tx RFIN - -7 -3 dB Output Return Loss, Antenna Port, Switch in Transmit Mode - -9 -4 dB Switch in Tx Position Reverse Isolation (Antenna Port to Tx Input Port) 30 40 - dB Switch in Tx Position, signal injected into Antenna port and measured at Tx input port, PA = "ON" Stability (Spurious) - -60 -50 dBc 6:1 VSWR, POUT = +18 dBm(1), -40 OC TON Settling Time - 1.0 2.0 s Harmonics 2fo 3fo COMMENTS 10% to 90% of maximum RF power. POUT = +16 dBm(1) Note: (1) Power as measured at Antenna port of AWL6254. 4 Data Sheet - Rev 2.0 02/2008 AWL6254 Table 5: Electrical Specifications - Tx Path 802.11g (TC = +25 °C, VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V , VBT_EN = 0 V, 64 QAM OFDM 54 Mbps) PARAMETER MIN TYP MAX UNIT Operating Frequency 2400 - 2500 MHz Power Gain 25 28 32 dB Gain Ripple - 1.5 2.0 dB Across 100 MHz band Error Vector Magnitude (EVM) - 3.3 -29.6 5.0 -26 % dB POUT = +16 dBm (1), (2) Pass - - N/A POUT = +16 dBm (2) Current Consumption 60 75 95 mA POUT = +16 dBm (2) Power Detector Voltage 650 780 900 mV POUT = +16 dBm (2) Power Detector Sensitivity 50 68 85 Tx Spectrum Mask COMMENTS mV/dB 10 dBm < POUT < +17 dBm (2) Note: (1) EVM includes system noise floor of 1% (-40 dB). (2) Power as measured at Antenna port of AWL6254 Table 6: Electrical Specifications - Tx Path 802.11b (TC = +25 °C, VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V , VBT_EN = 0 V, 1 Mbps, Gaussian Filtering, bT=0.50) PARAMETER MIN TYP MAX UNIT Operating Frequency 2400 - 2500 MHz Power Gain 25 28 32 dB Gain Ripple - 1.5 2.0 dB Across 100 MHz band Adjacent Channel Power (ACPR) 1st Sidelobe (11 - 22 MHz Offset) - -33 -30 dBr POUT = +18 dBm (1) Adjacent Channel Power (ACPR) 2nd Sidelobe (>22 MHz Offset) - -53 -50 dBr POUT = +18 dBm (1) Pass - - N/A POUT = +18 dBm (1) Current Consumption 75 100 125 mA POUT = +18 dBm (1) Power Detector Voltage 810 970 1115 mV POUT = +18 dBm (1) Power Detector Sensitivity 60 78 95 Tx Spectrum Mask COMMENTS mV/dB 10 dBm < POUT < +20 dBm (1) Note: (1) Power as measured at Antenna port of AWL6254 Data Sheet - Rev 2.0 02/2008 5 AWL6254 Table 7: DC Electrical Specifications - Rx Path Continuous Wave (TC = +25 °C, VCC = +3.6 V, VPA_EN = 0 V, VLNA_EN = +3.3 V , VBT_EN = 0 V) PARAMETER MIN TYP MAX UNIT Power Gain 10 13 16 dB Gain Ripple - 0.5 1.0 dB P1dB 4 6 - dBm Current at P1dB 9 13 17 mA Quiescent Current 9 13 17 mA Noise Figure - 2.3 3.9 dB Includes RF switch and LNA Return Loss, Rx RF Port - -12 -8 dB Switch in Rx position, Antenna port terminated in 50 load Return Loss, Antenna Port, Switch in Receive Mode - -7 -3 dB Switch in Rx position, with 50 Rx port load Isolation (Antenna Port to Rx Port) 22 29 - dB Switch in Tx position, signal injected into Antenna port and measured at Rx port, PA = "ON" S21 Performance (@ 1.9 GHz) - -6 0 dB Stability - -60 -50 dBc 6 COMMENTS Across 100 MHz Band Data Sheet - Rev 2.0 02/2008 AWL6254 Table 8: DC Electrical Specifications - Bluetooth Path Continuous Wave (TC = +25 °C, VCC = +3.6 V, VPA_EN = 0 V, VLNA_EN = 0 V , VBT_EN = +3.3 V) PARAMETER MIN TYP MAX UNIT Insertion Loss - 0.8 1.5 dB Quiescent Current - 60 125 A 20 25 - dBm Return Loss, Bluetooth RF Port - -10 -8 dB Switch in Bluetooth position, Antenna port terminated in 50 load Return Loss, Antenna Port, Switch in Bluetooth Mode - -10 -8 dB Switch in Bluetooth position, Bluetooth port terminated in 50 load 30 38 - dB Switch in Bluetooth position, signal injected into Antenna port and measured at Rx port P1dB Isolation (Antenna Port to Rx Port) COMMENTS 2.4 GHz to 2.5 GHz Table 9: Control Logic Truth Table PA ENABLE BLUETOOTH ENABLE LNA ENABLE PA STATUS LNA STATUS Shutdown 0 0 0 Off Off Not Connected WLAN Rx 0 0 1 Off On WLAN Rx Bluetooth 0 1 0 Off Off Bluetooth WLAN Tx 1 0 0 On Off WLAN Tx FEIC MODE SWITCH STATUS Note: 1. Logic State 0 = 0 - 0.4 V; Logic State 1 = 2.0 - 4.2 V Table 10: Control Voltages and Timing (TC = +25 °C, VCC = +3.6 V, Other Voltages Defined by Logic Below) PARAMETER MIN TYP MAX UNIT LNA Enable Pin Control Voltage +2.0 - - +0.4 V LNA = 1 LNA = 0 Bluetooth Enable Pin Control Voltage +2.0 - - +0.4 V Switch = 1 Switch = 0 PA Enable Pin Control Voltage +2.0 - - +0.4 V PA = 1 PA = 0 COMMENTS Note: 1. Logic State 0 = 0 - 0.4 V; Logic State 1 = 2.0 - 4.2 V Data Sheet - Rev 2.0 02/2008 7 AWL6254 PERFORMANCE DATA 32 320 34 340 30 300 32 320 28 280 30 300 26 260 Gain 24 28 Gain 2.50 GHz 200 18 Current 2.40 GHz Current 2.45 GHz Current 2.50 GHz 180 Gain -40C Gain +25C Gain +85C 200 18 Current -40C Current +25C Current +85C 180 160 14 140 12 120 10 100 8 80 8 6 60 6 40 4 20 2 0 0 Current 2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 220 20 16 4 16 160 14 140 12 120 10 100 80 60 20 0 0 20 1 2 3 4 5 6 7 32 320 30 300 28 220 Icc 4.2V 200 180 16 160 14 140 12 120 10 100 8 80 6 60 Current 4 20 0 0 2 3 4 5 6 7 8 9 10 11 16 17 18 19 12 13 14 15 16 17 18 19 5 4 3 2 1 0 20 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) Figure 6: Tx Path EVM vs. Output Power Across Temp (Freq = 2.45 GHz, VCC = +3.6 V) 802.11g 54 Mbps OFDM Figure 7: Tx Path EVM vs. Output Power Across Power Supply Voltage (Freq = 2.45 GHz, Figure 7: Tx Path EVM vs. Output Power Across Power Supply Voltage = 2.45 GHz, T54 = +25Mbps C 802.11g OFDM TA = +25oC)Freq 802.11g 54 Mbps OFDM 10 10 9 9 EVM -40C 8 7 EVM 3.3V 8 EVM +25C EVM 3.6V EVM 4.2V 7 EVM +85C EVM (%) 6 EVM (%) 15 EVM 2.50 GHz Output Power (dBm) 5 6 5 4 4 3 3 2 2 1 1 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0 1 Output Power (dBm) 8 14 6 40 2 1 13 EVM 2.45 GHz 7 EVM (%) Gain 4.2V 18 0 12 EVM 2.40 GHz 8 Current (mA) Gain (dB) Icc 3.6V 11 9 240 Icc 3.3V 10 10 260 24 Gain 3.6V 9 Figure 5: Tx Path EVM vs. Output Power Across o 5: Tx EVM vs. Across FreqFigure (VCC =Path +3.6 V,Output TA =Power +25 C)Frequency 802.11g Vcc = +3.6 V, T = +25 C 54802.11g Mbps OFDM 54 Mbps OFDM 280 Gain 26 Gain 3.3V 8 Output Power (dBm) Figure 4: Tx Path Gain and ICC vs. Output Power Across Voltage (Freq = 2.45 Figure 4:Power Tx Path Gain Supply and Icc vs. Output Power Across Power Supply Voltage GHz, Freq = 2.45 GHz, T = +25 C TA = +25oC)802.11g 802.11g 54 Mbps OFDM 54 Mbps OFDM 20 40 Current Output Power (dBm) 22 240 22 Gain (dB) Gain 2.45 GHz Current (mA) Gain 2.40 GHz 260 Gain 24 220 20 280 26 240 22 Gain (dB) Figure 3: Path Gain and ICC vs. Output Power Across Temp (Freq = 2.45 GHz, VCC = +3.6 V) Figure 3: Tx Path Gain and Icc vs. Output Power Across Temperature Frequency = 54 2.45 GHz, Voltage OFDM = +3.6 V 802.11g Mbps 802.11g 54 Mbps OFDM Current (mA) Figure 2: Tx Path Gain and Icc vs. Output Power = Output +3.6Power V, Across TA =Frequency +25oC) Across Figure 2: TxFreq Path Gain(V andCC Icc vs. Vcc = +3.6 V, T = +25 C 802.11g 5454 Mbps 802.11g Mbps OFDMOFDM Data Sheet - Rev 2.0 02/2008 2 3 4 5 6 7 8 9 10 11 12 Output Power (dBm) 13 14 15 16 17 18 19 20 AWL6254 Figure 8: Tx Path Detector Voltage vs. Output o Power Across Freq A = +25 C, VFrequency CC = +3.6 V) Figure 8: Tx Path Detector Voltage (T vs. Output Power Across Vcc = +3.6 V, T = +25 C 802.11g 54 Mbps OFDM 802.11g 54 Mbps OFDM Figure 9: Tx Path Detector Voltage vs. Output Power Across Temp (Freq = 2.45 GHz, VCC = +3.6 V) Figure 9: Tx Path Detector Voltage vs. Output Power Across Temperature Frequency = 2.45 GHz, = +3.6OFDM V 802.11g 54Voltage Mbps 802.11g 54 Mbps OFDM 1.2 1.2 1.1 1.0 Det. Volt. 2.40GHz 1.0 0.9 Det. Volt. 2.45GHz 0.9 0.8 Det. Volt. 2.50GHz 0.8 Detector Voltage (V) 0.7 0.6 0.5 0.4 Det. Volt. -40C Det. Volt. +25C Det. Volt.+85C 0.7 0.6 0.5 0.4 0.3 0.3 0.2 0.2 0.1 0.1 0.0 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0 20 1 2 3 4 5 6 7 8 Figure 10: Tx Path Detector Voltage vs. Output Power Across Supply Voltage (Freq = 2.45 GHz, Voltage = 2.45 GHz, T = +25 C TA = +25OFreq C) 802.11g 54 Mbps OFDM 802.11g 54 Mbps OFDM 10 11 12 13 14 15 16 17 18 1.1 32 320 30 300 28 1.0 0.8 Det. Volt. 4.2V 260 Gain 24 240 22 Gain (dB) Det. Volt. 3.6V 280 26 Det. Volt. 3.3V 0.9 0.7 0.6 0.5 220 20 Gain 2.40 GHz Gain 2.45 GHz Gain 2.50 GHz 200 18 Current 2.40 GHz Current 2.45 GHz Current 2.50 GHz 180 16 160 14 140 12 120 10 0.4 100 8 80 6 0.3 60 Current 4 0.2 40 2 0.1 20 0 0 0 1 2 3 4 5 6 7 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 19 Figure 11: Tx Path and ICC vs. Output Power o Across Freq (TIcc A = C ,V CC Frequency = +3.6 V) Figure 11: Tx Path Gain and vs. +25 Output Power Across Vcc = +3.6 V, T = +25 C 802.11b Gaussian (bT=0.5), 1 Mbps 802.11b Gaussian Filtering Filtering (bT = 0.5), 1 Mbps 1.2 Detector Voltage (V) 9 Output Power (dBm) Output Power (dBm) Current (mA) Detector Voltage (V) 1.1 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) 20 Output Power (dBm) Figure 13: Tx Path Gain and Icc vs. Output Power Figure 12: Tx Path Gain and ICC vs. Output Power Across Supply Voltage (Freq=2.45 GHz, TA = +25oC) Across Temp (Freq = 2.45 GHz, V CC = +3.6 V) 802.11b Figure 13: Tx Path Gain and Icc vs. Output Power Across Power Supply Voltage Figure 12: Tx Path Gain and Icc vs. Output Power Across Temperature Frequency = 2.45 GHz, Voltage = +3.6 V Freq = 2.45 GHz, T = +25 C 802.11b802.11b Gaussian Filtering (bT=0.5), 1 Mbps Gaussian Filtering (bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), 1 Mbps Gaussian Filtering (bT = 0.5), 1 Mbps 32 320 30 30 300 28 28 280 26 26 260 24 240 22 Gain Gain (dB) 24 22 220 20 200 18 Gain -40C Gain +25C Gain +85C 180 16 Current -40C Current +25C Current +85C 160 14 140 12 120 10 100 8 80 6 60 Current 4 2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Gain (dB) 340 32 Current (mA) 34 320 300 280 Gain 260 240 220 20 Gain 3.3V Gain 3.6V Gain 4.2V 200 18 Icc 3.3V Icc 3.6V Icc 4.2V 180 16 160 14 140 12 120 10 100 8 80 6 40 4 20 2 0 0 60 Current 40 20 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) Output Power (dBm) Data Sheet - Rev 2.0 02/2008 9 AWL6254 -22 -22 -26 -26 -30 -30 -34 -34 -38 ACPR Sidelobe (dBr) ACPR Sidelobe (dBr) Figure 14: Tx Path ACPR Sidelobes 1 & 2 vs. Figure 15: Tx Path ACPR Sidelobes 1 & 2 vs. Output Figure 14: Tx Path ACPR 1st & 2nd Sidelobes vs. Output Power Across Output Power Across Freq (Vcc = +3.6 V, TA = Power Across Temp Temperature (Freq = 2.45 GHz, VCC = +3.6 V) Frequency Frequency = 2.45 GHz, Voltage = +3.6 V Vcc = +3.6 V, T = +25 C +25oC) 802.11b Gaussian Filtering (bT=0.5), 1 Mbps 802.11b Gaussian Filtering 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), (bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), 1 Mbps 1st Sidelobe 2.40GHz 1st Sidelobe 2.45GHz 1st Sidelobe 2.50GHz 2nd Sidelobe 2.40GHz 2nd Sidelobe 2.45GHz 2nd Sidelobe 2.50GHz -42 -46 -50 -38 1st Sidelobe +25C -58 -58 -62 -62 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2nd Sidelobe -40C -50 -54 0 1st Sidelobe +85C -46 -54 -66 1st Sidelobe -40C -42 2nd Sidelobe +25C 2nd Sidelobe +85C -66 0 1 2 3 4 5 6 7 8 Figure 16: Tx Path ACPR Sidelobes 1 & 2 vs. Output Power Across Supply Voltage (Freq = 2.45 GHz, TA = Voltage Freq = 2.45 GHz, T = +25 C Gaussian Filtering (bT=0.5), 1 Mbps +25oC) 802.11b802.11b Gaussian Filtering (bT = 0.5), 1 Mbps 1.2 -26 1.1 Detector Voltage (V) ACPR Sidelobe (dBr) -34 -38 1st Sidelobe 3.30V 1st Sidelobe 3.60V 1st Sidelobe 4.20V 2nd Sidelobe 3.30V 2nd Sidelobe 3.60V 2nd Sidelobe 4.20V -54 14 15 16 17 18 19 Det. Volt. 2.50GHz 0.8 0.7 0.6 0.5 0.4 0.2 -62 0.1 -66 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0 1 2 3 4 5 6 7 Output Power (dBm) 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) Figure 18: Tx Path Detector Voltage vs. Output = +3.6 V) Across (Freq =vs.2.45 VCC Figure 18: Temp Tx Path Detector Voltage Output GHz, Power Across Temperature Frequency = 2.45 GHz, Voltage = +3.6 V 802.11b Gaussian Filtering (bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), 1 Mbps Figure 19: Tx Path Detector Voltage vs. Output Across Supply Voltage Voltage (Freq = 2.45 GHz, TA= Freq = 2.45 GHz, T = +25 C +25oC) 802.11b Gaussian Filtering (bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), 1 Mbps 1.2 1.2 1.1 1.1 Det. Volt. -40C 1.0 Det. Volt. +25C 0.9 Det. Volt.+85C 0.8 Detector Voltage (V) Detector Voltage (V) 13 0.3 -58 0.7 0.6 0.5 0.4 0.3 1.0 Det. Volt. 3.3V 0.9 Det. Volt. 3.6V 0.8 Det. Volt. 4.2V 0.7 0.6 0.5 0.4 0.3 0.2 0.2 0.1 0.1 0.0 0 1 2 3 4 5 6 7 8 9 10 11 Output Power (dBm) 10 12 Det. Volt. 2.45GHz 0.9 -50 11 Det. Volt. 2.40GHz 1.0 -30 -46 10 Figure 17: Tx Path Detector Voltage vs. Output o Across (VCC = vs. +3.6 TAAcross = +25 C) Figure 17: Tx Freq Path Detector Voltage OutputV, Power Frequency Vcc = +3.6 V, T = +25 C 802.11b Gaussian Filtering (bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), 1 Mbps -22 -42 9 Output Power (dBm) Output Power (dBm) 12 13 14 15 16 17 18 19 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 Output Power (dBm) Data Sheet - Rev 2.0 02/2008 13 14 15 16 17 18 19 20 AWL6254 Figure 20: Tx Path S-Parameters S21 Response Figure 20: Tx Path S-Parameters S21 V, Response (VCC = +3.6 TA = +25oC) Vcc = +3.6 V, T = +25 C 35 0 30 -2 25 -4 20 -6 15 -8 10 -10 5 -12 S11/S22 (dB) S21 Mag (dB) 0 S21 (dB) Figure 21: Tx Figure Path S-Parameters S11 & S22 21: Tx Path S-Parameters S11 & S22 Response Response (VVcc CC = +3.6 V, TA = +25oC) = +3.6 V, T = +25 C -5 -10 -15 -20 -14 -16 S11 Mag (dB) -18 S22 Mag (dB) -20 -25 -22 -30 -24 -35 -26 -40 -28 -45 -30 -50 -32 -55 -34 -60 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 0.0 15 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Frequency (GHz) Frequency (GHz) Figure 23: Receive Path Output P1dB Across Figure P1dBV, TA = +25oC) Freq (VCC = +3.6 V,23:VReceive LNA_Path ENOutput =+3.3 Figure 22: Receive Path Noise Figure Across Figure 22: Receive Path Noise Figure _EN =+3.3 V, TA = +25oC) Supply Voltage (V =+3.3 V, T=+25 C V LNA LNA_EN 2.5 Vcc=+3.6 V, VLNA_EN=+3.3 V, T=+25 C 15 2.4GHz 2.45 2.45GHz 2.50GHz +3.3V Noise Figure 2.4 14 +3.6V Noise Figure OP1dB Points 2.35 13 Gain (dB) Noise Figure (dB) +4.2V Noise Figure 2.3 2.25 12 2.2 11 2.15 2.1 2.4 2.41 2.42 2.43 2.44 2.45 2.46 2.47 2.48 2.49 2.5 10 -11 Frequency (GHz) -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 Output Power (dBm) Figure 24: Receive Path Output P1dB Across Supply Voltage (Freq =2.45 GHz, VLNA_EN=+3.3 V, Figure 24: Receive Path Output P1dB o =+3.3 V, T=+25 C Frequency =T 2.45 GHz, V A = +25 C) LNA_EN 15 -10 Figure 25: Rx Path S-Parameters S21 Response Figure 25: Rx Path S-Parameters S21 V, Response (VCC = +3.6 TA = +25oC) Vcc = +3.6 V, T = +25 C 20 15 +3.3 V 10 +3.6 V 14 5 +4.2 V 0 OP1dB Points -5 -10 Gain (dB) S21 (dB) 13 -15 -20 -25 -30 12 -35 S21 Mag (dB) -40 -45 11 -50 -55 -60 0 10 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 1 8 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Frequency (GHz) Output Power (dBm) Data Sheet - Rev 2.0 02/2008 11 AWL6254 Figure 26: Rx Path S-Parameters S21 & S22 26: Rx Path S-Parameters ResponseFigure (VS11 CC&= +3.6 V, TA = +25oC) S22 Response Figure 27: Bluetooth S-Parameters S21 Figure 27: Bluetooth S-Parameters Response (VCCS21=Response +3.6 V, TA = +25oC) Vcc = +3.6 V, T = +25 C 4 2.5 0 2.0 -2 1.5 -4 1.0 -6 S21 Mag (dB) 0.5 -8 0.0 -10 S21 (dB) S11/S22 (dB) Vcc = +3.6 V, T = +25 C 3.0 2 -12 -14 -16 S11 Mag (dB) -18 -1.0 -1.5 -2.0 S22 Mag (dB) -20 -0.5 -2.5 -22 -3.0 -24 -3.5 -26 -28 -4.0 -30 -4.5 -32 -5.0 0.0 -34 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0.5 5.0 Frequency (GHz) Figure 28:Bluetooth S-Parameters S11 & S22 Figure 28: Bluetooth S-Parameters S11 & S22 Response CC = +3.6 V, TA = +25oC) Response (VVcc = +3.6 V, T = +25 C 0 -1 -2 -3 S11 Mag (dB) -4 S22 Mag (dB) -5 S11/S22 (dB) -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Frequency (GHz) 12 Data Sheet - Rev 2.0 02/2008 1.0 1.5 2.0 2.5 3.0 3.5 Frequency (GHz) 4.0 4.5 5.0 5.5 6.0 AWL6254 APPLICATION INFORMATION CONNECT TO ANTENNA 13 DET_OUT 14 GND VCC VCC NC GND 12 11 C1 0.1 F 16 V 20 % 10 9 8 GND PA_IN PA_EN GND 7 4 RX_RF BT_EN 3 AWL6254 5 CONNECT TO RX GND 6 2 BLUETOOTH LNA_EN 1 ANT GND 16 CONNECT TO BLUETOOTH 15 DETECTOR OUTPUT 3-BIT CONTROL **NOTES** RF traces should be 18 mils wide with 20 mils of clearance. DC traces should be 8 mils wide with 8 mils of clearance. CONNECT TO TX Figure 29: Application Circuit Data Sheet - Rev 2.0 02/2008 13 AWL6254 PACKAGE OUTLINE C 4 A D I G Pin 1 16 1 H B Index Area F E Top View Side View Bottom View MILLIMETERS DIMENSION A B C D E F G H I MIN 2.90 2.90 0.50 0.00 1.55 TYP MAX 3.00 3.10 3.00 3.10 0.55 0.60 0.02 0.05 1.70 1.85 1.50 BSC. 0.18 0.25 0.30 0.50 BSC. 0.20 0.30 0.40 1. All dimensions are in millimeters, angles in degrees. 2. The terminal #1 identifier and pad numbering convention shall conform to JESD 95-1 SPP-012 . 3. Lead coplanarity: 0.05 max. 4. Dimension applies to metalized pad and is measured between 0.25 and 0.30 MM from pad tip. Figure 30: S35 Package Outline - 16 Pin 3 mm x 3 mm x 0.55 mm ULPCC Figure 31: Branding Specification 14 Data Sheet - Rev 2.0 02/2008 AWL6254 Figure 32: Recommended PCB Layout (all units are in mils) Data Sheet - Rev 2.0 02/2008 15 AWL6254 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWL6254RS35P8 -40 °C to +85 °C RoHS-compliant 16 Pin 3 mm x 3 mm x 0.55 mm Surface Mount IC 2,500 piece Tape and Reel EVA6254RS35 -40 °C to +85 °C RoHS-compliant 16 Pin 3 mm x 3 mm x 0.55 mm Surface Mount IC 1 piece Evaluation Board ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 16 Data Sheet - Rev 2.0 02/2008