AD EVAL-AD7741-42EBZ Single and multichannel, synchronous voltage-to-frequency converter Datasheet

a
Single and Multichannel, Synchronous
Voltage-to-Frequency Converters
AD7741/AD7742
FEATURES
AD7741: One Single-Ended Input Channel
AD7742: Two Differential or Three Pseudo-Differential
Input Channels
Integral Nonlinearity of 0.012% at fOUT(Max) = 2.75 MHz
(AD7742) and at fOUT(Max) = 1.35 MHz (AD7741)
Single +5 V Supply Operation
Buffered Inputs
Programmable Gain Analog Front-End
On-Chip +2.5 V Reference
Internal/External Reference Option
Power Down to 35 ␮A Max
Minimal External Components Required
8-Lead and 16-Lead DIP and SOIC Packages
FUNCTIONAL BLOCK DIAGRAMS
VDD
PD
REFIN/OUT
+2.5V
REFERENCE
VOLTAGE-TOFREQUENCY
MODULATOR
X1
VIN
fOUT
AD7741
CLOCK
GENERATION
CLKIN
APPLICATIONS
Low Cost Analog-to-Digital Conversion
Signal Isolation
CLKOUT
VDD
GND
PD
UNI/BIP
GAIN
AD7742
VIN1
VIN2
VIN3
GENERAL DESCRIPTION
The AD7741/AD7742 are a new generation of synchronous
voltage-to-frequency converters (VFCs). The AD7741 is a
single-channel version in an 8-lead package (SOIC/DIP) and the
AD7742 is a multichannel version in a 16-lead package (SOIC/
DIP). No user trimming is required to achieve the specified
performance.
The AD7741 has a single buffered input whereas the AD7742
has four buffered inputs that may be configured as two fullydifferential inputs or three pseudo-differential inputs. Both parts
include an on-chip +2.5 V bandgap reference that provides the
user with the option of using this internal reference or an external reference.
INPUT
MUX
POWER-DOWN
LOGIC
X1/X2
POWER-DOWN
LOGIC
VOLTAGE-TOFREQUENCY
MODULATOR
fOUT
VIN4
+2.5V
REFERENCE
CLOCK
GENERATION
A1
A0
GND
CLKIN
CLKOUT
REFIN
REFOUT
The AD7741 has a single-ended voltage input range from 0 V
to REFIN. The AD7742 has a differential voltage input range
from –VREF to +VREF. Both parts operate from a single +5 V
supply consuming typically 6 mA, and also contain a powerdown feature that reduces the current consumption to less than
35 µA.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999
(VDD = +4.75 V to +5.25 V; VREF = +2.5 V; fCLKIN = 6.144 MHz; all specifications TMIN to
MAX unless otherwise noted.)
AD7741–SPECIFICATIONS T
2
Parameter
DC PERFORMANCE
Integral Nonlinearity
fCLKIN = 200 kHz3
fCLKIN = 3 MHz3
fCLKIN = 6.144 MHz
Offset Error
Gain Error
Offset Error Drift3
Gain Error Drift3
Power Supply Rejection Ratio3
ANALOG INPUT5
Input Current
Input Voltage Range
+2.5 V REFERENCE (REFIN/OUT)
REFIN
Nominal Input Voltage
Input Impedance6
REFOUT
Output Voltage
Output Impedance3
Reference Drift3
Line Rejection
Reference Noise (0.1 Hz to 10 Hz)3
LOGIC OUTPUT
Output High Voltage, VOH
Output Low Voltage, VOL
Minimum Output Frequency
Maximum Output Frequency
LOGIC INPUT
PD ONLY
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current
Pin Capacitance
CLKIN ONLY
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current
Pin Capacitance
B and Y Version1
Min
Typ
Max
0
+0.8
± 30
± 16
–63
± 50
0
± 100
VREF
2.5
N/A
2.38
2.50
1
± 50
–60
100
% of Span4
% of Span
% of Span
mV
% of Span
µV/°C
ppm of Span/°C
dB
2.60
0.4
0.05 fCLKIN
0.45 fCLKIN
2.4
∆VDD = ± 5%
V
kΩ
ppm/°C
dB
µV p-p
V
V
Hz
Hz
6
V
V
nA
pF
6
0.8
±2
10
V
V
µA
pF
6.144
MHz
5.25
8
35
V
mA
µA
µs
3.5
15
30
VDD > 4.8 V
nA
V
0.8
± 100
10
4.75
Conditions/Comments
V
4.0
CLOCK FREQUENCY
Input Frequency
POWER REQUIREMENTS
VDD
IDD (Normal Mode)
IDD (Power-Down)
Power-Up Time3
± 0.012
± 0.012
± 0.024
± 40
+1.6
Units
Output Sourcing 800 µA7
Output Sinking 1.6 mA7
VIN = 0 V
VIN = VREF
For Specified Performance
Output Unloaded
Coming Out of Power-Down Mode
NOTES
1
Temperature ranges: B Version –40°C to +85°C: Y Version: –40°C to +105°C.
2
See Terminology.
3
Guaranteed by design and characterization, not production tested.
4
Span = Maximum Output Frequency–Minimum Output Frequency.
5
The absolute voltage on the input pin must not go more positive than V DD – 2.25 V or more negative than GND.
6
Because this pin is bidirectional, any external reference must be capable of sinking/sourcing 400 µA in order to overdrive the internal reference.
7
These logic levels apply to CLKOUT only when it is loaded with one CMOS load.
Specifications subject to change without notice.
–2–
REV. 0
AD7741/AD7742
AD7742–SPECIFICATIONS (VT
DD
MAX
= +4.75 V to +5.25 V; VREF = +2.5 V; fCLKIN = 6.144 MHz; all specifications TMIN to
unless otherwise noted.)
B Version1
Parameter3
Min
Typ
DC PERFORMANCE
Integral Nonlinearity
fCLKIN = 200 kHz4
fCLKIN = 3 MHz4
fCLKIN = 6.144 MHz
Offset Error
Gain Error
+0.2
+0.2
Offset Error Drift 4
Gain Error Drift 4
Power Supply Rejection Ratio 4
Channel-to-Channel Isolation 4
Common-Mode Rejection
ANALOG INPUTS (VIN1–VIN4)6
Input Current
Common-Mode Input Range
Differential Input Range
VOLTAGE REFERENCE
REFIN
Nominal Input Voltage
Input Impedance 4
fCLKIN = 3 MHz
fCLKIN = 6.144 MHz
REFOUT
Output Voltage
Output Impedance 4
Reference Drift 4
Line Rejection
Reference Noise
(0.1 Hz to 10 Hz) 4
LOGIC OUTPUT
Output High Voltage, V OH
Output Low Voltage, VOL
Minimum Output Frequency
–60
± 50
+0.5
–VREF/Gain
0
+0.2
+0.2
–58
± 100
VDD – 1.75 +0.5
+VREF/Gain –VREF/Gain
+VREF/Gain 0
2.38
Typ
+1.2
+1.2
± 12
± 12
±2
±4
–70
–75
–78
± 50
Max
Units
± 0.015
± 0.015
± 0.015
± 40
± 40
+2.2
+2.2
% of Span 5
% of Span
% of Span
mV
mV
% of Span
% of Span
µV/°C
µV/°C
ppm of Span/°C
ppm of Span/°C
dB
dB
dB
± 100
VDD – 1.75
+VREF/Gain
+VREF/Gain
nA
V
V
V
2.5
70
35
2.50
1
± 50
–70
2.60
2.38
100
2.50
1
± 50
–70
2.60
0.05 fCLKIN
0.05 fCLKIN
0.45 fCLKIN
0.45 fCLKIN
Hz
0.4
2.4
6
6
0.8
±2
10
3.5
6
0.8
± 100
10
V
V
nA
pF
6
0.8
±2
10
V
V
µA
pF
6.144
MHz
5.25
8
35
V
mA
µA
µs
3.5
6.144
4.75
6
25
30
5.25
8
35
4.75
6
25
30
NOTES
1
Temperature range: B Version: –40°C to +85°C.
Temperature range: Y Version: –40°C to +105°C.
See Terminology.
4
Guaranteed by design and characterization, not production tested.
5
Span = Maximum Output Frequency–Minimum Output Frequency.
6
The absolute voltage on the input pins must not go more positive than V DD – 1.75 V or more negative than +0.5 V.
7
These logic levels apply to CLKOUT only when it is loaded with one CMOS load.
2
3
Specifications subject to change without notice .
REV. 0
V
kΩ
ppm/°C
dB
V
V
Hz
0.8
± 100
10
–3–
Bipolar Mode
Unipolar Mode
µV p-p
4.0
0.4
2.4
Unipolar Mode
Bipolar Mode
Unipolar Mode
Bipolar Mode
Unipolar Mode
Bipolar Mode
Unipolar Mode
Bipolar Mode
∆VDD = ± 5%
kΩ
kΩ
100
4.0
Conditions/Comments
V
70
35
CLOCK FREQUENCY
Input Frequency
POWER REQUIREMENTS
VDD
IDD (Normal Mode)
IDD (Power-Down)
Power-Up Time 4
± 0.0122
± 0.0122
± 0.0122
± 40
± 40
+2.2
+2.2
Min
2.5
Maximum Output Frequency
LOGIC INPUT
ALL EXCEPT CLKIN
Input High Voltage, V IH
Input Low Voltage, V IL
Input Current
Pin Capacitance
CLKIN ONLY
Input High Voltage, V IH
Input Low Voltage, V IL
Input Current
Pin Capacitance
+1.2
+1.2
± 12
± 12
±2
±4
–70
–75
–78
Y Version2
Max
Output Sourcing 800 µA7
Output Sinking 1.6 mA7
VIN = 0 V (Unipolar), VIN =
–VREF/Gain (Bipolar)
VIN = VREF/Gain (Unipolar
and Bipolar)
For Specified Performance
Output Unloaded
Coming Out of PowerDown Mode
AD7741/AD7742
TIMING CHARACTERISTICS1, 2, 3 (V
Parameter
fCLKIN
tHIGH/tLOW
t1
t2
t3
t4
DD
= +4.75 V to +5.25 V; VREF = +2.5 V. All specifications TMIN to TMAX unless otherwise noted.)
Limit at TMIN, TMAX
(B and Y Version)
Units
6.144
55/45
45/55
9
4
4
tHIGH ± 5
MHz max
max
min
ns typ
ns typ
ns typ
ns typ
Conditions/Comments
Input Clock Mark/Space Ratio
fCLOCK Rising Edge to fOUT Rising Edge
fOUT Rise Time
fOUT Fall Time
fOUT Pulsewidth
NOTES
1
Guaranteed by design and characterization, not production tested.
2
All input signals are specified with tr = tf = 5 ns (10% to 90% of V DD) and timed from a voltage level of (V IL + VIH)/2.
3
See Figure 1.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS 1, 2
tHIGH
(TA = +25°C unless otherwise noted)
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3␣ V to +7 V
Analog Input Voltage to GND . . . . . . . . –5␣ V to VDD + 0.3 V
Digital Input Voltage to GND . . . . . . . –0.3␣ V to VDD + 0.3 V
Reference Input Voltage to GND . . . . –0.3 V to VDD + 0.3 V
fOUT to GND . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range
Automotive (Y Version) . . . . . . . . . . . . . . –40°C to +105°C
Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Plastic DIP Package
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . 450 mW
θJA Thermal Impedance (8 Lead) . . . . . . . . . . . . . 125°C/W
θJA Thermal Impedance (16 Lead) . . . . . . . . . . . . 117°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
SOIC Package
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . 450 mW
θJA Thermal Impedance (8 Lead) . . . . . . . . . . . . . 157°C/W
θJA Thermal Impedance (16 Lead) . . . . . . . . . . . . 125°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
CLKIN
t4
fOUT
t2
t1
t3
Figure 1. Timing Diagram
ORDERING GUIDE
Models
Temperature
Ranges
Package
Descriptions
Package
Options
AD7741BN
AD7741BR
AD7741YR
AD7742BN
AD7742BR
AD7742YR
–40°C to +85°C
–40°C to +85°C
–40°C to +105°C
–40°C to +85°C
–40°C to +85°C
–40°C to +105°C
Plastic DIP
Small Outline
Small Outline
Plastic DIP
Small Outline
Small Outline
N-8
R-8
R-8
N-16
R-16A
R-16A
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Transient currents of up to 100 mA will not cause SCR latch-up.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD7741/AD7742 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper
ESD precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. 0
AD7741/AD7742
AD7741 PIN FUNCTION DESCRIPTION
Pin No.
Mnemonic
Function
1
VDD
2
3
GND
CLKOUT
4
CLKIN
5
REFIN/OUT
6
VIN
7
PD
8
fOUT
Power Supply Input. These parts can be operated from +4.75 V to +5.25 V and the supply should
be adequately decoupled to GND.
Ground reference point for all circuitry on the part.
External Clock Output. When the master clock for the device is a crystal, the crystal is connected
between CLKIN and CLKOUT. When an external clock is applied to CLKIN, the CLKOUT pin
provides an inverted clock signal. This clock should be buffered if it is to be used as a clock source
elsewhere in the system.
External Clock Input. The master clock for the device can be provided in the form of a crystal or an
external clock. A crystal may be tied across the CLKIN and CLKOUT pins. Alternatively, the
CLKIN pin may be driven by a CMOS-compatible clock and CLKOUT left unconnected. The
frequency of the master clock may be as high as 6 MHz.
This is the reference input to the core of the VFC and defines the span of the VFC. If this pin is left
unconnected, the internal 2.5 V reference is used. Alternatively, a precision external reference (e.g.,
REF192) may be used to overdrive the internal reference. The internal bandgap reference has a
high output impedance in order to allow it to be overdriven.
The analog input to the VFC. It has an input range from 0 V to VREF. This input is buffered so it
draws virtually no current from whatever source is driving it.
Active Low Power-Down pin. When this input is low, the part enters power-down mode where it
typically consumes 15 µA of current.
Frequency Output. This pin provides the output of the synchronous VFC.
PIN CONFIGURATION
VDD 1
8
AD7741
fOUT
PD
TOP VIEW
CLKOUT 3 (Not to Scale) 6 VIN
GND 2
CLKIN 4
REV. 0
7
5
–5–
REFIN/OUT
AD7741/AD7742
AD7742 PIN FUNCTION DESCRIPTION
Pin No.
Mnemonic
Function
1
2
fOUT
VDD
3
4–5
6
GND
A1, A0
CLKOUT
7
CLKIN
8
UNI/BIP
9
REFOUT
10
REFIN
11
VIN1
12
VIN2
13
VIN3
14
VIN4
15
16
GAIN
PD
Frequency Output. This pin provides the output of the synchronous VFC.
Power Supply Input. These parts can be operated from +4.75 V to +5.25 V and the supply should be
adequately decoupled to GND.
Ground reference point for all circuitry on the part.
Address Inputs used to select the input channel configuration.
External Clock Output. When the master clock for the device is a crystal, the crystal is connected between CLKIN and CLKOUT. When an external clock is applied to CLKIN, the CLKOUT pin
provides an inverted clock signal. This clock should be buffered if it is to be used as a clock source
elsewhere in the system.
External Clock Input. The master clock for the device can be provided in the form of a crystal or an
external clock. A crystal may be tied across the CLKIN and CLKOUT pins. Alternatively, the CLKIN
pin may be driven by a CMOS-compatible clock and CLKOUT left unconnected. The frequency of the
master clock may be as high as 6 MHz.
Control input which determines whether the device operates with differential bipolar analog input
signals or differential unipolar analog input signals.
2.5 V Voltage Reference Output. This can be tied directly to REFIN. It may also be used as a reference
to other parts of the system provided it is buffered first.
This is the Reference Input to the core of the VFC and defines the span of the VFC. A 2.5 V reference
is required at this pin. This may be provided by connecting it directly to REFOUT or by using a precision external reference (e.g., REF192).
Buffered Analog Input Channel 1. This is either a pseudo-differential input with respect to VIN4 or it is
the positive input of a truly-differential input pair with respect to VIN2.
Buffered Analog Input Channel 2. This is either a pseudo-differential input with respect to VIN4 or it is
the negative input of a truly-differential input pair with respect to VIN1.
Buffered Analog Input Channel 3. This is the positive input of a truly-differential input pair with respect to VIN4.
Buffered Analog Input Channel 4. This is either the common for pseudo-differential input with respect
to VIN1 or VIN2 or it is the negative input of a truly-differential input pair with respect to VIN3.
Gain Select input that controls whether the gain on the analog front-end is X1 or X2.
Active Low Power-Down pin. When this input is low, the part enters power-down mode where it typically consumes 25 µA of current.
PIN CONFIGURATION
fOUT 1
16 PD
VDD 2
15 GAIN
GND 3
A1 4
14 VIN4
AD7742
13 VIN3
TOP VIEW
A0 5 (Not to Scale) 12 VIN2
CLKOUT 6
11 VIN1
CLKIN 7
10 REFIN
UNI/BIP 8
9
–6–
REFOUT
REV. 0
AD7741/AD7742
TERMINOLOGY
GENERAL DESCRIPTION
INTEGRAL NONLINEARITY
The AD7741/AD7742 are a new generation of CMOS synchronous Voltage-to-Frequency Converters (VFCs) that use a
charge-balance conversion technique. The AD7741 is a singlechannel version and the AD7742 is a multichannel version. The
input voltage signal is applied to a proprietary programmable
gain front-end based around an analog modulator that converts
the input voltage into an output pulse train.
For the VFC, Integral Nonlinearity (INL) is a measure of the
maximum deviation from a straight line passing through the
actual endpoints of the VFC transfer function. The error is
expressed in % of the frequency span:
Frequency Span = fOUT(max) – fOUT(min)
The parts also contain an on-chip +2.5 V bandgap reference
and operate from a single +5 V supply. A block diagram of the
AD7742 is shown in Figure 2.
OFFSET ERROR
This is a measure of the offset error of the VFC. Ideally, the
minimum output frequency (corresponding to minimum input
voltage) is 5% of fCLKIN The deviation from this value is the
offset error. It is expressed in terms of the error referred to the
input voltage. It is expressed in mV.
INTEGRATOR
VIN1
VIN2
GAIN ERROR
VIN3
This is a measure of the span error of the VFC. The gain is the
scale factor that relates the input VIN to the output fOUT. The
gain error is the deviation in slope of the actual VFC transfer
characteristic from the ideal expressed as a percentage of the
full-scale span.
VIN4
fOUT
INPUT
MUX
SWITCHED
CAPS
Figure 2. AD7742 Block Diagram
Input Amplifier Stage
The buffered input stage for the analog inputs presents a high
impedance, allowing significant external source impedances.
The four analog inputs (VIN1 through VIN4) each have a voltage
range from +0.5 V to VDD – 1.75 V. This is an absolute voltage
range and is relative to the GND pin.
OFFSET ERROR DRIFT
This is a measure of the change in Offset Error with changes in
temperature. It is expressed in µV/°C.
GAIN ERROR DRIFT
In the case of the AD7742 multichannel part, a differential
multiplexer switches one of the differential input channels to the
VFC modulator. The multiplexer is controlled by two pins, A1
and A0. See Table I for channel configurations.
This is a measure of the change in Gain Error with changes in
temperature. It is expressed in (ppm of span)/°C.
POWER-SUPPLY REJECTION RATIO (PSRR)
This indicates how the output of the VFC is affected by changes
in the supply voltage. Again, this error is referred to the input
voltage. The input voltage is kept constant and the VDD supply
is varied ± 5%. The ratio of the apparent change in input voltage
to the change in VDD is measured in dBs.
Table I. AD7742 Input Channel Selection
CHANNEL-TO-CHANNEL ISOLATION
This is a ratio of the amplitude of the signal at the input of one
channel to a sine wave on the input of another channel. It is
measured in dBs.
A1
A0
VIN(+)
VIN(–)
Type
0
0
1
1
0
1
0
1
VIN1
VIN2
VIN3
VIN1
VIN4
VIN4
VIN4
VIN2
Pseudo Differential
Pseudo Differential
Full Differential
Full Differential
Analog Input Ranges
The AD7741 has a unipolar single-ended input channel whereas
the AD7742 contains four input channels which may be configured as two fully differential channels or as three pseudodifferential channels. The AD7742 also has a X1/X2 gain
option on the front end. The channel and gain settings are
pin-programmable.
COMMON-MODE REJECTION
For the AD7742, the output frequency should remain unchanged provided the differential input remains unchanged
although its common-mode level may change. The CMR is the
ratio of the apparent change in differential input voltage to the
actual change in common-mode voltage. It is expressed in dBs.
REV. 0
COMPARATOR
SWITCHED
CAPS
The AD7742 uses differential inputs to provide common-mode
noise rejection (i.e., the converted result will correspond to the
differential voltage between the two inputs). The absolute voltage
on both inputs must lie between +0.5 V and VDD –1.75 V.
–7–
AD7741/AD7742
Table II. AD7741/AD7742 Input Range Selection
UNI/BIP
GAIN
Gain, G
VIN(Min)
fOUT = 0.05 fCLKIN
VIN(Max)
fOUT = 0.45 fCLKIN
Part
N/A
0
0
1
1
N/A
0
1
0
1
X1
X1
X2
X1
X2
0
–VREF
–VREF/2
0
0
+VREF
+VREF
+VREF/2
+VREF
+VREF/2
AD7741
AD7742
AD7742
AD7742
AD7742
As can be seen from Table II, the AD7741 has one input range
configuration whereas the AD7742 has unipolar/bipolar as
well as gain options depending on the status of the GAIN
and UNI/BIP pins.
OUTPUT
FREQUENCY
fOUT
fOUTMAX
(0.45 fCLKIN)
The transfer function for the AD7741 is shown in Figure 3.
Figure 4 shows the AD7742 transfer function for unipolar input
range configuration while the AD7742 transfer function for
bipolar input range configuration is shown in Figure 5.
fOUTMIN
(0.05 fCLKIN)
OUTPUT
FREQUENCY
fOUT
VREF
–
fOUTMAX
(0.45 fCLKIN)
+
GAIN
VREF
DIFFERENTIAL
INPUT VOLTAGE
GAIN
Figure 5. AD7742 Transfer Characteristic for Bipolar
Differential Input Range: –VREF/Gain to +VREF/Gain; the
common-mode range must be between +0.5 V and
VDD – 1.75 V. UNI/BIP pin tied to GND.
VFC Modulator
fOUTMIN
The analog input signal to the AD7741/AD7742 is continuously sampled by a switched capacitor modulator whose sampling rate is set by a master clock input that may be supplied
externally or by a crystal-controlled on-chip clock oscillator.
However, the input signal is buffered on-chip before being applied to the sampling capacitor of the modulator. This isolates
the sampling capacitor charging currents from the analog input
pins.
(0.05 fCLKIN)
0
REFIN
INPUT
VOLTAGE VIN
Figure 3. AD7741 Transfer Characteristic for Input Range
from 0 to VREF
OUTPUT
FREQUENCY
fOUT
This system is a negative feedback loop that tries to keep the net
charge on the integrator capacitor at zero, by balancing charge
injected by the input voltage with charge injected by the VREF.
The output of the comparator provides the digital input for the
1-bit DAC, so that the system functions as a negative feedback
loop that tries to minimize the difference signal (see Figure 6).
fOUTMAX
(0.45 fCLKIN)
CLK
fOUTMIN
(0.05 fCLKIN)
INTEGRATOR
COMPARATOR
0
+
VREF
GAIN
DIFFERENTIAL
INPUT VOLTAGE
INPUT
+
S
+
1-BIT
STREAM
–
–
Figure 4. AD7742 Transfer Characteristic for Unipolar
Differential Input Range: 0 V to VREF/Gain; the input
common-mode range must be between +0.5 V and
VDD – 1.75 V. UNI/BIP pin tied to VDD.
+VREF
–VREF
Figure 6. AD7741/AD7742 Modulator Loop
–8–
REV. 0
AD7741/AD7742
The digital data that represents the analog input voltage is contained in the duty cycle of the pulse train appearing at the output of the comparator. The output is a fixed-width pulse whose
frequency depends on the analog input signal. The input voltage
is offset internally so that a full-scale input gives an output frequency of 0.45 fCLKIN and zero-scale input gives an output frequency of 0.05 fCLKIN. The output allows simple interfacing to
either standard logic families or opto-couplers. The clock high
period controls the pulsewidth of the frequency output. The
pulse is initiated by the edge of the clock signal. The delay time
between the edge of the clock and the edge of the frequency
output is typically 9 ns. Figure 7 shows the waveform of this
frequency output.
AD7741/AD7742
TO OTHER
CIRCUITRY
5MV
CLKIN
C1
C2
Figure 8. On-Chip Oscillator
The on-chip oscillator circuit also has a start-up time associated
with it before it oscillates at its correct frequency and correct
voltage levels. The typical start-up time for the circuit is 5 ms
(with a 6.144 MHz crystal).
After power-up, or if there is a step change in input voltage,
there is a settling time that must elapse before valid data is
obtained. This is typically 2 CLKIN cycles on the AD7742 and
10 CLKIN cycles on the AD7741.
The AD7741/AD7742 master clock appears on the CLKOUT
pin of the device. The maximum recommended load on this pin
is one CMOS load. When using a crystal to generate the AD7741/
AD7742 clock it may be desirable to then use this clock as the
clock source for the system. In this case it is recommended that
the CLKOUT signal be buffered with a CMOS buffer before
being applied to the rest of the circuit.
fCLKIN
fOUT = fCLKIN/4
VIN = VREF/2
fOUT = fCLKIN/10
VIN = VREF/8
Reference Input
The AD7741/AD7742 performs conversion relative to an applied
reference voltage that allows easy interfacing to ratiometric
systems. This reference may be applied using the internal 2.5 V
bandgap reference. For the AD7741, this is done by simply
leaving REFIN/OUT unconnected. For the AD7742, REFIN is
tied to REFOUT. Alternatively, an external reference, e.g.,
REF192 or AD780, may be used. For the AD7741, this is connected to REFIN/OUT and will overdrive the internal reference. For the AD7742, it is connected directly to the REFIN
pin.
fOUT = fCLKIN*3/20
VIN = VREF/4
6 TCLK
7 TCLK
AVERAGE fOUT IS fCLKIN *3/20 BUT THE ACTUAL PULSE STREAM
VARIES BETWEEN fCLKIN/6 AND fCLKIN/7
Figure 7. AD7741/AD7742 Frequency Output Waveforms
Clock Generation
As distinct from the asynchronous VFCs which rely on the stability
of an external capacitor to set their full-scale frequency, the
AD7741/AD7742 uses an external clock to define the full-scale
output frequency. The result is a more stable, more linear transfer function and also allows the designer to determine the system stability and drift based upon the external clock selected. A
crystal oscillator may also be used if desired.
While the internal reference will be adequate for most applications, power supply rejection and overall regulation may be
improved through the use of an external precision reference.
The process of selecting an external voltage reference should
include consideration of drive capability, initial error, noise and
drift characteristics. A suitable choice would be the AD780 or
REF192.
The AD7741/AD7742 requires a master clock input, which may
be an external CMOS-compatible clock signal applied to the
CLKIN pin (CLKOUT not used). Alternatively, a crystal of the
correct frequency can be connected between CLKIN and
CLKOUT, when the clock circuit will function as a crystal
controlled oscillator. Figure 8 shows a simple model of the onchip oscillator.
REV. 0
CLKOUT
Power-Down Mode
The low power standby mode is initiated by taking the PD pin
low, which shuts down most of the analog and digital circuitry.
This reduces the power consumption to 185 µW max.
–9–
AD7741/AD7742
APPLICATIONS
The basic connection diagram for the part is shown in Figure 9.
In the connection diagram shown, the AD7742 analog inputs
are configured as fully differential, bipolar inputs with a gain of
1. A quartz crystal provides the master clock source for the part.
It may be necessary to connect capacitors (C1 and C2 in the
diagram) on the crystal to ensure that it does not oscillate at overtones of its fundamental operating frequency. The values of capacitors will vary depending on the manufacturer’s specifications.
VIN
AD7741
fOUT
COUNTER
TO mP
GATE
SIGNAL
CLKIN
FREQUENCY
DIVIDER
CLOCK
GENERATOR
Figure 10. A/D Conversion Using the AD7741 VFC
+5V
4096x TCLOCK
fCLKIN
VDD
VIN1
DIFF
INPUT 1
PD
REFOUT
VIN2
fOUT
REFIN
VIN3
DIFF
INPUT 2
AD7742
VIN4
GATE
GND
A0
CHANNEL
SELECT
fOUT
UNI/BIP
A1
TGATE
Figure 11. Waveforms in an A/D Converter Using a VFC
GAIN
CLKIN
C1
The clock frequency and the gate time determine the resolution
of such an ADC. If 12-bit resolution is required and fCLKIN is
5 MHz (therefore, fOUT max is 2.25 MHz), the minimum gate
time required is calculated as follows:
CLKOUT
C2
N counts at Full Scale (2.25 MHz) will take
Figure 9. Basic Connection Diagram
(N/2.25 × 106) seconds = minimum gate time.
A/D Conversion Techniques Using the AD7741/AD7742
When used as an ADC, VFCs provide certain advantages including accuracy, linearity and being inherently monotonic. The
AD7741/AD7742 has a true integrating input which smooths
out noise peaks.
The most popular method of using a VFC in an A/D system is
to count the output pulses of fOUT for a fixed gate interval (see
Figure 10). This fixed gate interval should be generated by
dividing down the clock input frequency. This ensures that any
errors due to clock jitter or clock frequency drift are eliminated.
The ratio of the fOUT to the clock frequency is what is important
here, not the absolute value of fOUT. The frequency division can
be done by a binary counter where fCLKIN is the CLK input.
Figure 11 shows the waveforms of fCLKIN, fOUT and the Gate
signal. A counter counts the rising edges of fOUT while the Gate
signal is high. Since the gate interval is not synchronized with
fOUT, there is a possibility of a counting inaccuracy. Depending
on fOUT, an error of one count may occur.
N is the total number of codes for a given resolution; 4096 for
12 bits
minimum gate time = (4096/2.25 × 106) sec = 1.820 ms.
Since TGATE × fOUT max = number of counts at full scale, a
faster conversion with the same resolution can be performed
with a higher fOUT max. This high fOUT max (3 MHz) is a main
feature of the AD7741/AD7742.
If the output frequency is measured by counting pulses gated to
a signal which is derived from the clock, the clock stability is
unimportant and the device simply performs as a voltagecontrolled frequency divider, producing a high resolution ADC.
The inherent monotonicity of the transfer function and wide
range of input clock frequencies allows the conversion time and
resolution to be optimized for specific applications.
There is another parameter is taken into account when choosing
the length of the gate interval. Because the integration period of
the system is equal to the gate interval, any interfering signal can
be rejected by counting for an integer number of periods of the
interfering signal. For example, a gate interval of 100 ms will
give normal-mode rejection of 50 Hz and 60 Hz signals.
–10–
REV. 0
AD7741/AD7742
Isolation Applications
Power Supply Bypassing and Grounding
In addition to analog-to-digital conversion, the AD7741/AD7742
can be used in isolated analog signal transmission applications.
Due to noise, safety requirements or distance, it may be necessary to isolate the AD7741/AD7742 from any controlling
circuitry. This can easily be achieved by using opto-isolators,
which will provide isolation in excess of 3 kV.
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure
the rated performance. The printed circuit board housing the
AD7741/AD7742 should be designed so the analog and digital
sections are separated and confined to certain areas of the board.
Opto-electronic coupling is a popular method of isolated signal
coupling. In this type of device, the signal is coupled from an
input LED to an output photo-transistor, with light as the connecting medium. This technique allows dc to be transmitted, is
extremely useful in overcoming ground loops between equipment, and is applicable over a wide range of speeds and power.
The analog voltage to be transmitted is converted to a pulse
train using the VFC. An opto-isolator circuit is used to couple
this pulse train across an isolation barrier using light as the
connecting medium. The input LED of the isolator is driven
from the output of the AD7741/AD7742. At the receiver side,
the output transistor is operated in the photo-transistor mode.
The pulse train can be reconverted to an analog voltage using a
frequency-to-voltage converter; alternatively, the pulse train can
be fed into a counter to generate a digital signal.
The analog and digital sections of the AD7741/AD7742 have
been designed to allow operation from a single-ended power
source, simplifying its use with isolated power supplies.
Figure 12 shows a general purpose VFC circuit using a low cost
opto-isolator. A +5 V power supply is assumed for both the
isolated (+5 V isolated) and local (+5 V local) supplies.
VCC
+5V
VDD
R
IN
AD774x
OPTOCOUPLER
fOUT
GND2
GND1
To minimize capacitive coupling between them, digital and
analog ground planes should only be joined in one place, close
to the DUT and should not overlap.
Avoid running digital lines under the device as these will couple
noise onto the die. The analog ground plane should be allowed
to run under the AD7742 to avoid noise coupling. The power
supply lines to the AD7742 should use as large a trace as possible to provide low impedance paths and reduce the effects of
glitches on the power supply line. Fast switching signals like
clocks should be shielded with digital ground to avoid radiating
noise to other parts of the board and clock signals should never
be run near analog inputs. Avoid crossover of digital and analog
signals. Traces on opposite sides of the board should run at
right angles to each other. This reduces the effect of feedthrough
through the board. A microstrip technique is by far the best but
is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to the ground
plane while the signal traces are placed on the solder side.
Good decoupling is also important. All analog supplies should
be decoupled to GND with surface mount capacitors, 10 µF in
parallel with 0.1 µF located as close to the package as possible,
ideally right up against the device. The lead lengths on the bypass capacitor should be as short as possible. It is essential that
these capacitors be placed physically close to the AD7741/AD7742
to minimize the inductance of the PCB trace between the capacitor and the supply pin. The 10 µF are the tantalum bead
type and are located in the vicinity of the VFC to reduce lowfrequency ripple. The 0.1 µF capacitors should have low Effective Series Resistance (ESR) and Effective Series Inductance
(ESI), such as the common ceramic types, which provide a low
impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Additionally, it is
beneficial to have large capacitors (> 47 µF) located at the point
where the power connects to the PCB.
ISOLATION
BARRIER
Figure 12. Opto-Isolated Application
REV. 0
–11–
AD7741/AD7742
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead SO
(R-8)
0.430 (10.92)
0.348 (8.84)
8
5
1
PIN 1
0.1968 (5.00)
0.1890 (4.80)
0.280 (7.11)
0.240 (6.10)
0.1574 (4.00)
0.1497 (3.80)
4
0.100 (2.54)
BSC
0.210
(5.33)
MAX
C3601–8–5/99
8-Lead Plastic DIP
(N-8)
0.325 (8.25)
0.300 (7.62)
0.060 (1.52)
0.015 (0.38)
4
0.2440 (6.20)
0.2284 (5.80)
0.0196 (0.50)
3 458
0.0099 (0.25)
0.0500 (1.27)
BSC
0.195 (4.95)
0.115 (2.93)
0.102 (2.59)
0.094 (2.39)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
0.015 (0.381)
0.008 (0.204)
0.022 (0.558) 0.070 (1.77) SEATING
0.014 (0.356) 0.045 (1.15) PLANE
5
1
PIN 1
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
8
16-Lead Plastic DIP
(N-16)
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
88
08 0.0500 (1.27)
0.0160 (0.41)
16-Lead Narrow Body SO
(R-16A)
0.840 (21.34)
0.745 (18.92)
0.3937 (10.00)
0.3859 (9.80)
9
1
8
0.280 (7.11)
0.240 (6.10)
PIN 1
0.060 (1.52)
0.015 (0.38)
0.210 (5.33)
MAX
0.130
(3.30)
0.160 (4.06)
MIN
0.115 (2.93)
0.022 (0.558) 0.100 0.070 (1.77) SEATING
PLANE
(2.54)
0.014 (0.356)
0.045 (1.15)
BSC
0.1574 (4.00)
0.1497 (3.80)
0.325 (8.25)
0.300 (7.62)
PIN 1
0.195 (4.95)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
16
9
1
8
0.050 (1.27)
BSC
0.0098 (0.25)
0.0040 (0.10)
0.2440 (6.20)
0.2284 (5.80)
0.0688 (1.75)
0.0532 (1.35)
0.0196 (0.50)
3 458
0.0099 (0.25)
88
0.0192 (0.49) SEATING 0.0099 (0.25) 08 0.0500 (1.27)
PLANE
0.0138 (0.35)
0.0160 (0.41)
0.0075 (0.19)
PRINTED IN U.S.A.
16
–12–
REV. 0
Similar pages