Microchip F16KM202 General purpose, 16-bit flash microcontroller with xlp technology data sheet Datasheet

PIC24FV16KM204 FAMILY
General Purpose, 16-Bit Flash Microcontroller
with XLP Technology Data Sheet
Analog Peripheral Features
• Up to Two 8-Bit Digital-to-Analog Converters
(DAC):
- Soft Reset disable function allows DAC to
retain its output value through non-VDD
Resets
- Support for Idle mode
- Support for left and right-justified input data
• Two Operational Amplifiers (Op Amps):
- Differential inputs
- Selectable power/speed levels:
- Low power/low speed
- High power/high speed
• Up to 22-Channel, 10/12-Bit Analog-to-Digital
Converter:
- 100k samples/second at 12-bit conversion
rate (single Sample-and-Hold)
- Auto-scan with Threshold Detect
- Can operate during Sleep
- Dedicated band gap reference and
temperature sensor input
• Up to Three Rail-to-Rail Analog Comparators:
- Programmable reference voltage for
comparators
- Band gap reference input
- Flexible input multiplexing
- Low-power or high-speed selection options
• Charge Time Measurement Unit (CTMU):
- Capacitive measurement, up to 22 channels
- Time measurement down to 200 ps
resolution
- Up to 16 external Trigger pairs
• Internal Temperature Sensor with Dedicated A/D
Converter Input
 2013 Microchip Technology Inc.
Multiple/Single Capture Compare
Peripheral (MCCP/SCCP) Features
• 16 or 32-Bit Time Base
• 16 or 32-Bit Capture
- 4-Deep Capture Buffer
• 16 or 32-Bit Compare:
- Single Edge Compare modes
- Dual Edge Compare/PWM modes
- Center-Aligned Compare mode
- Variable Frequency Pulse mode
• Fully Asynchronous Operation, Available in
Sleep modes
• Single Output Steerable mode (MCCP only)
• Brush DC Forward and Reverse modes
(MCCP only)
• Half-Bridge with Dead-Time Delay (MCCP only)
• Push-Pull PWM mode (MCCP only)
• Auto-Shutdown with Programmable Source and
Shutdown State
• Programmable Output Polarity
Advance Information
DS33030A-page 1
PIC24FV16KM204 FAMILY
UART
12-Bit A/D Channels
8-Bit DAC
Op Amp
Comparators
CTMU
RTCC
CLC
2K
512
2.0-5.5
1
3/2
2
2
22
2
2
3
Yes
Yes
2
3
FV16KM202
28
16K
2K
512
2.0-5.5
1
3/2
2
2
19
2
2
3
Yes
Yes
2
3
FV08KM204
44
8K
2K
512
2.0-5.5
1
3/2
2
2
22
2
2
3
Yes
Yes
2
3
FV08KM202
28
8K
2K
512
2.0-5.5
1
3/2
2
2
19
2
2
3
Yes
Yes
2
3
FV16KM104
44
16K
1K
512
2.0-5.5
1
1/1
1
1
22
—
—
1
Yes
—
1
3
FV16KM102
28
16K
1K
512
2.0-5.5
1
1/1
1
1
19
—
—
1
Yes
—
1
3
FV08KM102
28
8K
1K
512
2.0-5.5
1
1/1
1
1
19
—
—
1
Yes
—
1
3
FV08KM101
20
8K
1K
512
2.0-5.5
1
1/1
1
1
16
—
—
1
Yes
—
1
3
ICD BRKPT
16-Bit Timer
16K
MSSP
Voltage Range (V)
44
16-Bit MCCP/SCCP
EE Data (bytes)
FV16KM204
Device
Pins
SRAM (bytes)
Peripherals
Flash Program (bytes)
Memory
5V Devices
3V Devices
F16KM204
44
16K
2K
512
1.8-3.6
1
3/2
2
2
22
2
2
3
Yes
Yes
2
3
F16KM202
28
16K
2K
512
1.8-3.6
1
3/2
2
2
19
2
2
3
Yes
Yes
2
3
F08KM204
44
8K
2K
512
1.8-3.6
1
3/2
2
2
22
2
2
3
Yes
Yes
2
3
F08KM202
28
8K
2K
512
1.8-3.6
1
3/2
2
2
19
2
2
3
Yes
Yes
2
3
F16KM104
44
16K
1K
512
1.8-3.6
1
1/1
1
1
22
—
—
1
Yes
—
1
3
F16KM102
28
16K
1K
512
1.8-3.6
1
1/1
1
1
19
—
—
1
Yes
—
1
3
F08KM102
28
8K
1K
512
1.8-3.6
1
1/1
1
1
19
—
—
1
Yes
—
1
3
F08KM101
20
8K
1K
512
1.8-3.6
1
1/1
1
1
16
—
—
1
Yes
—
1
3
DS33030A-page 2
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Special Microcontroller Features
High-Performance RISC CPU
• Wide Operating Voltage Range Options:
- 1.8V to 3.6V (PIC24F devices)
- 2.0V to 5.0V (PIC24FV devices)
• Selectable Power Management modes:
- Idle: CPU shuts down, allowing for significant
power reduction
- Sleep: CPU and peripherals shut down for
substantial power reduction and fast wake-up
- Retention Sleep mode: PIC24FV devices can
enter Sleep mode, employing the
retention regulator, further reducing power
consumption
- Doze: CPU can run at a lower frequency than
peripherals, a user-programmable feature
- Alternate Clock modes allow on-the-fly
switching to a lower clock speed for selective
power reduction
• Fail-Safe Clock Monitor:
- Detects clock failure and switches to on-chip,
low-power RC oscillator
• Ultra Low-Power Wake-up Pin Provides an
External Trigger for Wake from Sleep
• 10,000 Erase/Write Cycle Endurance Flash
Program Memory, Typical
• 100,000 Erase/Write Cycle Endurance
Data EEPROM, Typical
• Flash and Data EEPROM Data Retention: 20 Years
Minimum
• Self-Programmable under Software Control
• Power-on Reset (POR), Power-up Timer (PWRT)
and Oscillator Start-up Timer (OST)
• Watchdog Timer (WDT) with its Own On-Chip
RC Oscillator for Reliable Operation
• On-Chip Regulator for 5V Operation
• Selectable Windowed WDT Feature
• Selectable Oscillator Options including:
- 4x Phase Locked Loop (PLL)
• 8 MHz (FRC) Internal RC Oscillator:
- HS/EC, high-speed crystal/resonator
oscillator or external clock
• In-Circuit Serial Programming™ (ICSP™) and
In-Circuit Emulation (ICE) – via Two Pins
• In-Circuit Debugging
• Programmable High/Low-Voltage
Detect (HLVD) module
• Programmable Brown-out Reset (BOR):
- Software enable feature
- Configurable shutdown in Sleep
- Auto-configures power mode and sensitivity
based on device operating speed
- LPBOR available for re-arming of the POR
• Modified Harvard Architecture
• Operating Speed:
- DC – 32 MHz clock input
- 16 MIPS at 32 MHz clock input
• 8 MHz Internal Oscillator:
- 4x PLL option
- Multiple clock divide options
- Fast start-up
• 17-Bit x 17-Bit Single-Cycle Hardware
Fractional/Integer Multiplier
• 32-Bit by 16-Bit Hardware Divider
• 16 x 16-Bit Working Register Array
• C Compiler Optimized Instruction Set Architecture
• 24-Bit-Wide Instructions
• 16-Bit-Wide Data Path
• Linear Program Memory Addressing, up to
6 Mbytes
• Linear Data Memory Addressing, up to 64 Kbytes
• Two Address Generation Units (AGUs) for Separate
Read and Write Addressing of Data Memory
 2013 Microchip Technology Inc.
Peripheral Features
• High-Current Sink/Source, 18 mA/18 mA All Ports
• Independent Ultra Low-Power, 32 kHz
Timer Oscillator
• Up to Two Master Synchronous Serial Ports
(MSSPs) with SPI and I2C™ modes:
In SPI mode:
- User-configurable SCKx and SDOx pin outputs
- Daisy-chaining of SPI slave devices
In I2C mode:
- Serial clock synchronization (clock stretching)
- Bus collision detection and will arbitrate
accordingly
- Support for 16-bit read/write interface
• Up to Two Enhanced Addressable UARTs:
- LIN/J2602 bus support (auto-wake-up,
Auto-Baud Detect, Break character support)
- High and low speed (SCI)
- IrDA® mode (hardware encoder/decoder
function)
• Two External Interrupt Pins
• Hardware Real-Time Clock and Calendar (RTCC)
• Configurable Reference Clock Output (REFO)
• Two Configurable Logic Cells (CLC)
• Up to Two Single Output Capture/Compare/PWM
(SCCP) modules and up to Three Multiple Output
Capture/Compare/PWM (MCCP) modules
Advance Information
DS33030A-page 3
PIC24FV16KM204 FAMILY
20-Pin SPDIP/SSOP/SOIC
RA5
RA0
RA1
RB0
RB1
RB2
RA2
RA3
RB4
RA4
1
2
3
4
5
6
7
8
9
10
PIC24F08KM101
Pin Diagrams
20
19
18
17
16
15
14
13
12
11
VDD
VSS
RB15
RB14
RB13
RB12
RA6 OR VDDCORE
RB9
RB8
RB7
Pin Features
Pin
PIC24F08KM101
1
MCLR/VPP/RA5
2
PGC2/CVREF+/VREF+/AN0/CN2/RA0
3
PGD2/CVREF-/VREF-/AN1/CN3/RA1
4
PGD1/AN2/CTCMP/ULPWU/C1IND/OC2A/CN4/RB0
5
PGC1/AN3/C1INC/CTED12/CN5/RB1
6
AN4/U1RX/TCKIB/CTED13/CN6/RB2
7
OSCI/CLKI/AN13/C1INB/CN30/RA2
8
OSCO/CLKO/AN14/C1INA/CN29/RA3
9
PGD3/SOSCI/AN15/CLCINA/CN1/RB4
PIC24FVKM08KM101
10
PGC3/SOSCO/SCLKI/AN16/PWRLCLK/CLCINB/CN0/RA4
11
AN19/U1TX/CTED1/INT0/CN23/RB7
12
AN20/SCL1/U1CTS/OC1B/CTED10/CN22/RB8
13
AN21/SDA1/T1CK/U1RTS/U1BCLK/IC2/CLC1O/CTED4/CN21/RB9
AN19/U1TX/IC1/OC1A/CTED1/INT0/CN23/RB7
14
IC1/OC1A/INT2/CN8/RA6
VCAP OR VDDCORE
15
AN12/HLVDIN/SCK1/OC1C/CTED2/CN14/RB12
AN12/HLVDIN/SCK1/OC1C/CTED2/INT2/CN14/RB12
16
AN11/SDO1/OCFB/OC1D/CTPLS/CN13/RB13
17
CVREF/AN10/SDI1/C1OUT/OCFA/CTED5/INT1/CN12/RB14
18
AN9/REFO/SS1/TCKIA/CTED6/CN11/RB15
19
VSS/AVSS
20
VDD/AVDD
DS33030A-page 4
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
CVREF-
20
19 18 17
16
RA5
CVREF+
RB0 1
RA0
20-Pin QFN
RA1
Pin Diagrams (Continued)
15
RB1 2
RB15
14 RB14
RB2 3
PIC24F08KM101 13 RB13
RA2 4
8
RB7
9
10
RB9
7
RB8
6
RA4
12 RB12
RB4
RA3 5
11
RA6 or VDDCORE
Pin Features
Pin
PIC24F08KM101
1
PGD1/AN2/CTCMP/ULPWU/C1IND/OC2A/CN4/RB0
2
PGC1/AN3/C1INC/CTED12/CN5/RB1
3
AN4/U1RX/TCKIB/CTED13/CN6/RB2
4
OSCI/CLKI/AN13/C1INB/CN30/RA2
5
OSCO/CLKO/AN14/C1INA/CN29/RA3
6
PGD3/SOSCI/AN15/CLCINA/CN1/RB4
7
PGC3/SOSCO/SCLKI/AN16/PWRLCLK/CLCINB/CN0/RA4
8
AN19/U1TX/CTED1/INT0/CN23/RB7
9
AN20/SCL1/U1CTS/OC1B/CTED10/CN22/RB8
PIC24FV08KM101
AN19/U1TX/IC1/OC1A/CTED1/INT0/CN23/RB7
10
AN21/SDA1/T1CK/U1RTS/U1BCLK/IC2/CLC1O/CTED4/CN21/RB9
11
IC1/OC1A/INT2/CN8/RA6
VCAP OR VDDCORE
12
AN12/HLVDIN/SCK1/OC1C/CTED2/CN14/RB12
AN12/HLVDIN/SCK1/OC1C/CTED2/INT2/CN14/RB12
13
AN11/SDO1/OCFB/OC1D/CTPLS/CN13/RB13
14
CVREF/AN10/SDI1/C1OUT/OCFA/CTED5/INT1/CN12/RB14
15
AN9/REFO/SS1/TCKIA/CTED6/CN11/RB15
16
VSS/AVSS
17
VDD/AVDD
18
MCLR/VPP/RA5
MCLR/VPP/RA5
19
PGC2/CVREF+ /VREF+/AN0/CN2/RA0
PGC2/CVREF+ /VREF+/AN0/CN2/RA0
20
PGD2/CVREF-/VREF-/AN1/CN3/RA1
PGD2/CVREF-/VREF-/AN1/CN3/RA1
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 5
PIC24FV16KM204 FAMILY
28-Pin SPDIP/SSOP/SOIC
MCLR/RA5
RA0
RA1
RB0
RB1
RB2
RB3
VSS
RA2
RA3
RB4
RA4
VDD
RB5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIC24F16KMX02
Pin Diagrams (Continued)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
AVDD
AVSS
RB15
RB14
RB13
RB12
RB11
RB10
RA6 or VDDCORE
RA7
RB9
RB8
RB7
RB6
Pin Features
Pin
PIC24FXXKMX02
PIC24FVXXKMX02
1
MCLR/VPP/RA5
2
CVREF+/VREF+/DAC1REF+/AN0/C3INC/CN2/RA0
3
CVREF-/VREF-/AN1/CN3/RA1
4
PGD1/AN2/CTCMP/ULPWU/C1IND/C2INB/C3IND/U2TX/CN4/RB0
5
PGC1/OA1INA/OA2INA/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1
6
OA1INB/OA2INB/AN4/C1INB/C2IND/SDA2/U1RX/TCKIB/CTED13/CN6/RB2
CVREF-/VREF-/AN1/RA1
7
OA1OUT/AN5/C1INA/C2INC/SCL2/CN7/RB3
8
VSS
9
OSCI/CLKI/AN13/CN30/RA2
10
OSCO/CLKO/AN14/CN29/RA3
11
SOSCI/AN15/U2RTS/U2BCLK/CN1/RB4
12
SOSCO/SCLKI/AN16/PWRLCLK/U2CTS/CN0/RA4
13
VDD
14
PGD3/AN17/ASDA1/SCK2/IC4/OC1E/CLCINA/CN27/RB5
15
PGC3/AN18/ASCL1/SDO2/IC5/OC1F/CLCINB/CN24/RB6
16
AN19/U1TX/INT0/CN23/RB7
17
AN20/SCL1/U1CTS/C3OUT/OC1B/CTED10/CN22/RB8
18
AN21/SDA1/T1CK/U1RTS/U1BCLK/IC2/OC4/CLC1O/CTED4/CN21/RB9
19
SDI2/IC1/OC5/CLC2O/CTED3/CN9/RA7
AN19/U1TX/C2OUT/OC1A/INT0/CN23/RB7
20
C2OUT/OC1A/CTED1/INT2/CN8/RA6
21
PGD2/SDI1/OC3A/OC1C/CTED11/CN16/RB10
VCAP OR VDDCORE
22
PGC2/SCK1/OC2A/CTED9/CN15/RB11
23
DAC1OUT/AN12/HLVDIN/SS2/IC3/OC2B/CTED2/CN14/RB12
DAC1OUT/AN12/HLVDIN/SS2/IC3/OC2B/CTED2/INT2/CN14/
RB12
24
OA1INC/OA2INC/AN11/SDO1/OCFB/OC3B/OC1D/CTPLS/CN13/RB13
25
DAC2OUT/CVREF/OA1IND/OA2IND/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14
26
DAC2REF+/OA2OUT/AN9/C3INA/REFO/SS1/TCKIA/CTED6/CN11/RB15
27
VSS/AVSS
28
VDD/AVDD
Legend:
Values in red indicate pin function differences between PIC24F(V)XXKM202 and PIC24F(V)XXKM102 devices.
DS33030A-page 6
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
RA1
RA0
MCLR/RA5
VDD
VSS
RB15
RB14
Pin Diagrams (Continued)
28-Pin QFN(1)
28 27 26 25 24 23 22
1
21
2
20
3 PIC24F16KMX02 19
4
18
5
17
6
16
7
15
8 9 10 11 12 13 14
RB13
RB12
RB11
RB10
RA6 OR VDDCORE
RA7
RB9
RB4
RA4
VDD
RB5
RB6
RB7
RB8
RB0
RB1
RB2
RB3
VSS
RA2
RA3
Pin Features
Pin Features
PIC24FXXKMX02
PIC24FVXXKMX02
Pin
1
PGD1/AN2/CTCMP/ULPWU/C1IND/C2INB/C3IND/U2TX/CN4/RB0
2
PGC1/OA1INA/OA2INA/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1
3
OA1INB/OA2INB/AN4/C1INB/C2IND/SDA2/U1RX/TCKIB/CTED13/CN6/RB2
4
OA1OUT/AN5/C1INA/C2INC/SCL2/CN7/RB3
5
VSS
6
OSCI/CLKI/AN13/CN30/RA2
7
OSCO/CLKO/AN14/CN29/RA3
8
SOSCI/AN15/U2RTS/U2BCLK/CN1/RB4
9
SOSCO/SCLKI/AN16/PWRLCLK/U2CTS/CN0/RA4
10
VDD
11
PGD3/AN17/ASDA1/SCK2/IC4/OC1E/CLCINA/CN27/RB5
12
PGC3/AN18/ASCL1/SDO2/IC5/OC1F/CLCINB/CN24/RB6
13
AN19/U1TX/INT0/CN23/RB7
14
AN20/SCL1/U1CTS/C3OUT/OC1B/CTED10/CN22/RB8
AN19/U1TX/C2OUT/OC1A/INT0/CN23/RB7
15
AN21/SDA1/T1CK/U1RTS/U1BCLK/IC2/OC4/CLC1O/CTED4/CN21/RB9
16
SDI2/IC1/OC5/CLC2O/CTED3/CN9/RA7
17
C2OUT/OC1A/CTED1/INT2/CN8/RA6
18
PGD2/SDI1/OC3A/OC1C/CTED11/CN16/RB10
VDDCORE/VCAP
19
PGC2/SCK1/OC2A/CTED9/CN15/RB11
20
DAC1OUT/AN12/HLVDIN/SS2/IC3/OC2B/CTED2/CN14/RB12
21
OA1INC/OA2INC/AN11/SDO1/OCFB/OC3B/OC1D/CTPLS/CN13/RB13
22
DAC2OUT/CVREF/OA1IND/OA2IND/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14
DAC1OUT/AN12/HLVDIN/SS2/IC3/OC2B/CTED2/INT2/CN14/RB12
23
DAC2REF+/OA2OUT/AN9/C3INA/REFO/SS1/TCKIA/CTED6/CN11/RB15
24
VSS
25
VDD
26
MCLR/VPP/RA5
27
CVREF+/VREF+/DAC1REF+/AN0/C3INC/CN2/RA0
CVREF+/VREF+/DAC1REF+/AN0/C3INC/CTED1/CN2/RA0
28
CVREF-/VREF-/AN1/CN3/RA1
CVREF-/VREF-/AN1/CN3/RA1
Legend:
Values in red indicate pin function differences between PIC24F(V)XXKM202 and PIC24F(V)XXKM102 devices.
Note 1:
Exposed pad on underside of device is connected to VSS.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 7
PIC24FV16KM204 FAMILY
Pin Diagrams (Continued)
44-Pin TQFP/QFN(1)
RB8
RB7
RB6
RB5
VDD
VSS
RC5
RC4
RC3
RA9
RA4
44
43
42
41
40
39
38
37
36
35
34
PIC24FXXKMX04
33
32
31
30
29
28
27
26
25
24
23
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
RB4
RA8
RA3
RA2
VSS
VDD
RC2
RC1
RC0
RB3
RB2
RA10
RA11
RB14
RB15
AVSS
AVDD
MCLR/RA5
RA0
RA1
RB0
RB1
RB9
RC6
RC7
RC8
RC9
RA7
RA6
RB10
RB11
RB12
RB13
Pin Features
Pin
PIC24FXXKMX04
PIC24FVXXKMX04
1
AN21/SDA1/T1CK/U1RTS/U1BCLK/IC2/OC4/CLC1O/CTED4/CN21/RB9
2
U1RX/OC2C/CN18/RC6
3
U1TX/OC2D/CN17/RC7
4
OC2E/CN20/RC8
5
IC4/OC2F/CTED7/CN19/RC9
6
IC1/OC5/CLC2O/CTED3/CN9/RA7
7
C2OUT/OC1A/CTED1/INT2/CN8/RA6
8
PGD2/SDI1/OC1C/CTED11/CN16/RB10
9
PGC2/SCK1/OC2A/CTED9/CN15/RB11
10 DAC1OUT/AN12/HLVDIN/OC2B/CTED2/
CN14/RB12
VCAP or VDDCORE
DAC1OUT/AN12/HLVDIN/OC2B/CTED2/INT2/
CN14/RB12
11 OA1INC/OA2INC/AN11/SDO1/OC1D/CTPLS/CN13/RB13
12 IC5/OC3A/CN35/RA10
13 IC3/OC3B/CTED8/CN36/RA11
14 DAC2OUT/CVREF/OA1IND/OA2IND/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/
RB14
15 DAC2REF+/OA2OUT/AN9/C3INA/REFO/SS1/TCKIA/CTED6/CN11/RB15
16 AVSS
17 AVDD
18 MCLR/VPP/RA5
19 CVREF+/VREF+/DAC1REF+/AN0/C3INC/CN2/ CVREF+/VREF+/DAC1REF+/AN0/C3INC/
RA0
CTED1/CN2/RA0
20 CVREF-/VREF-/AN1/CN3/RA1
21 PGD1/AN2/CTCMP/ULPWU/C1IND/C2INB/C3IND/U2TX/CN4/RB0
22 PGC1/OA1INA/OA2INA/AN3/C1INC/C2INA/
U2RX/CTED12/CN5//RB1
OA1INA/OA2INA/AN3/C1INC/C2INA/U2RX/
CTED12/CN5/RB1
23 OA1INB/OA2INB/AN4/C1INB/C2IND/SDA2/TCKIB/CTED13/CN6/RB2
24 OA1OUT/AN5/C1INA/C2INC/SCL2/CN7/RB3
25 AN6/CN32/RC0
26 AN7/CN31/RC1
27 AN8/CN10/RC2
28 VDD
29 VSS
30 OSCI/CLKI/AN13/CN30/RA2
31 OSCO/CLKO/AN14/CN29/RA3
32 OCFB/CN33/RA8
33 SOSCI/AN15/U2RTS/U2BCLK/CN1/RB4
34 SOSCO/SCLKI/AN16/PWRLCLK/U2CTS/CN0/RA4
35 SS2/CN34/RA9
36 SDI2/CN28/RC3
37 SDO2/CN25/RC4
Legend: Values in red indicate pin
function differences between
PIC24F(V)XXKM202 and
PIC24F(V)XXKM102 devices.
Note 1: Exposed pad on underside of
device is connected to VSS.
38 SCK2/CN26/RC5
39 VSS
40 VDD
41 PGD3/AN17/ASDA1/OC1E/CLCINA/CN27/RB5
42 PGC3/AN18/ASCL1/OC1F/CLCINB/CN24/RB6
43 AN19/INT0/CN23/RB7
AN19/C2OUT/OC1A/INT0/CN23/RB7
44 AN20/SCL1/U1CTS/C3OUT/OC1B/CTED10/CN22/RB8
DS33030A-page 8
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Pin Diagrams (Continued)
48-Pin UQFN(1)
RB8
RB7
RB6
RB5
n/c
VDD
VSS
RC5
RC4
RC3
RA9
RA4
AN21/SDA1/T1CK/U1RTS/U1BCLK/IC2/OC4/CLC1O/CTED4/CN21/RB9
U1RX/OC2C/CN18/RC6
48
47
46
45
44
43
42
41
40
39
38
37
PIC24FVXXKMX04
2
3
U1TX/OC2D/CN17/RC7
4
OC2/CN20/RC8
5
IC4/OC2F/CTED7/CN19/RC9
PIC24FXXKMX04
PIC24FVXXKMX04
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
PIC24FXXKMX04
1
36
35
34
33
32
31
30
29
28
27
26
25
RB4
RA8
RA3
RA2
n/c
VSS
VDD
RC2
RC1
RC0
RB3
RB2
RA10
RA11
RB14
RB15
VSS/AVSS
VDD/AVDD
MCLR/RA5
n/c
RA0
RA1
RB0
RB1
RB9
RC6
RC7
RC8
RC9
RA7
RA6
n/c
RB10
RB11
RB12
RB13
Pin Features
Pin
Legend: Values in red indicate pin
function differences between
PIC24F(V)XXKM202 and
PIC24F(V)XXKM102 devices.
Note 1: Exposed pad on underside of
device is connected to VSS.
 2013 Microchip Technology Inc.
6
IC1/OC5/CLC2O/CTED3/CN9/RA7
7
VDDCORE or VCAP
C2OUT/OC1A/CTED1/INT2/CN8/RA6
8
n/c
n/c
9
PGD2/SDI1/OC1C/CTED11/CN16/RB10
10
PGC2/SCK1/OC2A/CTED9/CN15/RB11
11
DAC1OUT/AN12/HLVDIN/OC2B/CTED2/
CN14/RB12
12
OA1INC/OA2INC/AN11/SDO1/OC1D/CTPLS/CN13/RB13
13
IC5/OC3A/CN35/RA10
14
IC3/OC3B/CTED8/CN36/RA11
15
DAC2OUT/CVREF/OA1IND/OA2IND/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/
CN12/RB14
DAC1OUT/AN12/HLVDIN/OC2B/CTED2/
INT2/CN14/RB12
16
DAC2REF+/OA2OUT/AN9/C3INA/REFO/SS1/TCKIA/CTED6/CN11/RB15
17
VSS/AVSS
18
VDD/AVDD
19
MCLR/VPP/RA5
20
n/c
21
CVREF+/VREF+/DAC1REF+/AN0/C3INC/
CN2/RA0
CVREF+/VREF+/DAC1REF+/AN0/C3INC/
CTED1/CN2/RA0
22
CVREF-/VREF-/AN1/CN3/RA1
CVREF-/VREF-/AN1/CN3/RA1
23
PGD1/AN2/CTCMP/ULPWU/C1IND/C2INB/C3IND/U2TX/CN4/RB0
24
PGC1/OA1INA/OA2INA/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1
25
OA1INB/OA2INB/AN4/C1INB/C2IND/SDA2/
TCKIB/CTED13/CN6/RB2
26
OA1OUT/AN5/C1INA/C2INC/SCL2/CN7/RB3
27
AN6/CN32/RC0
28
AN7/CN31/RC1
29
AN8/CN10/RC2
30
VDD
31
VSS
AN4/C1INB/C2IND/SDA2/T5CK/
T4CK/CTED13/CN6/RB2
32
n/c
33
OSCI/AN13/CLKI/CN30/RA2
34
OSCO/CLKO/AN14/CN29/RA3
35
OCFB/CN33/RA8
36
SOSCI/AN15/U2RTS/U2BCLK/CN1/RB4
37
SOSCO/SCLKI/AN16/PWRLCLK/U2CTS/CN0/RA4
38
SS2/CN34/RA9
39
SDI2/CN28/RC3
40
SDO2/CN25/RC4
41
SCK2/CN26/RC5
42
VSS
43
VDD
44
n/c
45
PGD3/AN17/ASDA1/OC1E/CLCINA/CN27/RB5
46
PGC3/AN18/ASCL1/OC1F/CLCINB/CN24/RB6
47
AN19/C2OUT/INT0/CN23/RB7
48
AN20/SCL1/U1CTS/C3OUT/OC1B/CTED10/CN22/RB8
Advance Information
AN19/OC1A/INT0/CN23/RB7
DS33030A-page 9
PIC24FV16KM204 FAMILY
Table of Contents
1.0 Device Overview ........................................................................................................................................................................ 13
2.0 Guidelines for Getting Started with 16-Bit Microcontrollers ........................................................................................................ 29
3.0 CPU ........................................................................................................................................................................................... 35
4.0 Memory Organization ................................................................................................................................................................. 41
5.0 Flash Program Memory .............................................................................................................................................................. 67
6.0 Data EEPROM Memory ............................................................................................................................................................. 73
7.0 Resets ........................................................................................................................................................................................ 79
8.0 Interrupt Controller ..................................................................................................................................................................... 85
9.0 Oscillator Configuration ............................................................................................................................................................ 121
10.0 Power-Saving Features ............................................................................................................................................................ 131
11.0 I/O Ports ................................................................................................................................................................................... 137
12.0 Timer1 ..................................................................................................................................................................................... 141
13.0 Capture/Compare/PWM/Timer Modules (MCCP and SCCP) .................................................................................................. 143
14.0 Master Synchronous Serial Port (MSSP) ................................................................................................................................. 159
15.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 173
16.0 Real-Time Clock and Calendar (RTCC) .................................................................................................................................. 181
17.0 Configurable Logic Cell (CLC).................................................................................................................................................. 195
18.0 High/Low-Voltage Detect (HLVD)............................................................................................................................................. 207
19.0 12-Bit A/D Converter with Threshold Detect ............................................................................................................................ 209
20.0 8-Bit Digital-to-Analog Converter (DAC)................................................................................................................................... 229
21.0 Dual Operational Amplifier Module........................................................................................................................................... 233
22.0 Comparator Module.................................................................................................................................................................. 235
23.0 Comparator Voltage Reference................................................................................................................................................ 239
24.0 Charge Time Measurement Unit (CTMU) ................................................................................................................................ 241
25.0 Special Features ...................................................................................................................................................................... 249
26.0 Development Support............................................................................................................................................................... 261
27.0 Electrical Characteristics .......................................................................................................................................................... 265
28.0 Packaging Information.............................................................................................................................................................. 297
Appendix A: Revision History............................................................................................................................................................. 323
Index ................................................................................................................................................................................................. 325
The Microchip Web Site ..................................................................................................................................................................... 331
Customer Change Notification Service .............................................................................................................................................. 331
Customer Support .............................................................................................................................................................................. 331
Reader Response .............................................................................................................................................................................. 332
Product Identification System............................................................................................................................................................. 333
DS33030A-page 10
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 11
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 12
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
1.0
DEVICE OVERVIEW
1.1.2
This document contains device-specific information for
the following devices:
• PIC24FV08KM101
• PIC24F08KM101
• PIC24FV08KM102
• PIC24F08KM102
• PIC24FV16KM102
• PIC24F16KM102
• PIC24FV16KM104
• PIC24F16KM104
• PIC24FV08KM202
• PIC24F08KM202
• PIC24FV08KM204
• PIC24F08KM204
• PIC24FV16KM202
• PIC24F16KM202
• PIC24FV16KM204
• PIC24F16KM204
The PIC24FV16KM204 family introduces many new
analog features to the extreme low-power Microchip
devices. This is a 16-bit microcontroller family with a
broad peripheral feature set and enhanced computational performance. This family also offers a new
migration option for those high-performance applications which may be outgrowing their 8-bit platforms, but
do not require the numerical processing power of a
Digital Signal Processor (DSC).
1.1
1.1.1
16-BIT ARCHITECTURE
Central to all PIC24F devices is the 16-bit modified
Harvard architecture, first introduced with Microchip’s
dsPIC® Digital Signal Controllers. The PIC24F CPU
core offers a wide range of enhancements, such as:
• 16-bit data and 24-bit address paths with the
ability to move information between data and
memory spaces
• Linear addressing of up to 16 Mbytes (program
space) and 16 Kbytes (data)
• A 16-element working register array with built-in
software stack support
• A 17 x 17 hardware multiplier with support for
integer math
• Hardware support for 32-bit by 16-bit division
• An instruction set that supports multiple addressing modes and is optimized for high-level
languages, such as C
• Operational performance up to 16 MIPS
 2013 Microchip Technology Inc.
All of the devices in the PIC24FV16KM204 family incorporate a range of features that can significantly reduce
power consumption during operation. Key features
include:
• On-the-Fly Clock Switching, to allow the device
clock to be changed under software control to the
Timer1 source or the internal, low-power RC
oscillator during operation, allowing users to
incorporate power-saving ideas into their software
designs.
• Doze Mode Operation, when timing-sensitive
applications, such as serial communications,
require the uninterrupted operation of peripherals,
the CPU clock speed can be selectively reduced,
allowing incremental power savings without
missing a beat.
• Instruction-Based Power-Saving Modes, to allow
the microcontroller to suspend all operations or
selectively shut down its core while leaving its
peripherals active with a single instruction in
software.
1.1.3
Core Features
POWER-SAVING TECHNOLOGY
OSCILLATOR OPTIONS AND
FEATURES
The PIC24FV16KM204 family offers five different oscillator options, allowing users a range of choices in
developing application hardware. These include:
• Two Crystal modes using crystals or ceramic
resonators.
• Two External Clock modes offering the option of a
divide-by-2 clock output.
• Two Fast Internal oscillators (FRCs), one with a
nominal 8 MHz output and the other with a
nominal 500 kHz output. These outputs can also
be divided under software control to provide clock
speed as low as 31 kHz or 2 kHz.
• A Phase Locked Loop (PLL) frequency multiplier,
available to the external oscillator modes and the
8 MHz FRC oscillator, which allows clock speeds
of up to 32 MHz.
• A separate internal RC oscillator (LPRC) with a
fixed 31 kHz output, which provides a low-power
option for timing-insensitive applications.
The internal oscillator block also provides a stable reference source for the Fail-Safe Clock Monitor (FSCM).
This option constantly monitors the main clock source
against a reference signal provided by the internal
oscillator and enables the controller to switch to the
internal oscillator, allowing for continued low-speed
operation or a safe application shutdown.
Advance Information
DS33030A-page 13
PIC24FV16KM204 FAMILY
1.1.4
1.3
EASY MIGRATION
The PIC24FV16KM204 family devices have two
variants. The KM20X variant provides the full feature set
of the device, while the KM10X offers a reduced peripheral set, allowing for the balance of features and cost
(refer to Table 1-1). Both variants allow for a smooth
migration path as applications grow and evolve.
The consistent pinout scheme used throughout the entire
family also helps in migrating to the next larger device.
This is true when moving between devices with the same
pin count, different die variants, or even moving from
20-pin or 28-pin devices to 44-pin/48-pin devices.
The PIC24F family is pin compatible with devices in the
dsPIC33 family, and shares some compatibility with the
pinout schema for PIC18 and dsPIC30. This extends
the ability of applications to grow from the relatively
simple to the powerful and complex, yet still selecting a
Microchip device.
1.2
Other Special Features
• Communications: The PIC24FV16KM204 family
incorporates a range of serial communication
peripherals to handle a range of application
requirements. There is an MSSP module which
implements both SPI and I2C™ protocols, and
supports both Master and Slave modes of
operation for each. Devices also include one of
two UARTs with built-in IrDA® encoders/decoders.
• Analog Features: Select members of the
PIC24FV16KM204 family include two 8-bit
Digital-to-Analog Converters which offer support
in Idle mode, and left and right-justified input data,
as well as up to two operational amplifiers with
selectable power and speed modes.
• Real-Time Clock/Calendar (RTCC): This module
implements a full-featured clock and calendar with
alarm functions in hardware, freeing up timer
resources and program memory space for use of
the core application.
• 12-Bit A/D Converter: This module incorporates
programmable acquisition time, allowing for a
channel to be selected and a conversion to be
initiated without waiting for a sampling period and
faster sampling speed. The 16-deep result buffer
can be used either in Sleep, to reduce power, or in
Active mode to improve throughput.
• Charge Time Measurement Unit (CTMU) Interface:
The PIC24FV16KM204 family includes the new
CTMU interface module, which can be used for
capacitive touch sensing, proximity sensing, and
also for precision time measurement and pulse
generation. The CTMU can also be connected to
the operational amplifiers to provide active guarding, which provides increased robustness in the
presence of noise in capacitive touch applications.
DS33030A-page 14
Details on Individual Family
Members
Devices in the PIC24FV16KM204 family are available
in 20-pin, 28-pin, 44-pin and 48-pin packages. The
general block diagram for all devices is shown in
Figure 1-1.
Members of the PIC24FV16KM204 family are available
as both standard and high-voltage devices. High-voltage
devices, designated with an “FV” in the part number
(such as PIC24FV16KM204), accommodate an operating VDD range of 2.0V to 5.5V and have an on-board
voltage regulator that powers the core. Peripherals
operate at VDD.
Standard devices, designated by “F” (such as
PIC24F16KM204), function over a lower VDD range of
1.8V to 3.6V. These parts do not have an internal regulator, and both the core and peripherals operate directly
from VDD.
The PIC24FV16KM204 family may be thought of as
two different device groups, both offering slightly different sets of features. These differ from each other in
multiple ways:
•
•
•
•
•
•
The size of the Flash program memory
The number of external analog channels available
The number of Digital-to-Analog Converters
The number of operational amplifiers
The number of analog comparators
The presence of a Real-Time Clock and Calendar
(RTCC)
• The number and type of CCP modules (i.e.,
MCCP vs. SCCP)
• The number of serial communication modules
(both MSSPs and UARTs)
• The number of Configurable Logic
Cell (CLC) modules.
The general differences between the different
sub-families are shown in Table 1-1 and Table 1-2.
A list of the pin features available on the
PIC24FV16KM204 family devices, sorted by function,
is provided in Table 1-5.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Operating Frequency
DC-32 MHz
Program Memory (bytes)
16K
8K
Program Memory (instructions)
5632
2816
Data Memory (bytes)
16K
8K
5632
2816
2048
Data EEPROM Memory (bytes)
512
Interrupt Sources (soft vectors/NMI traps)
40 (36/4)
Voltage Range
1.8-3.6V
I/O Ports
PORTA<11:0>
PORTB<15:0>
PORTC<9:0>
PORTA<7:0>
PORTB<15:0>
38
24
Total I/O Pins
Timers
11
(One 16-Bit Timer, five MCCP/SCCP with up to two 16/32 timers each)
Capture/Compare/PWM modules
MCCP
SCCP
3
2
Serial Communications
MSSP
UART
2
2
Input Change Notification Interrupt
12-Bit Analog-to-Digital Module
(input channels)
37
22
23
22
19
Analog Comparators
3
8-Bit Digital-to-Analog Converters
2
Operational Amplifiers
2
Charge Time Measurement Unit (CTMU)
Yes
Real-Time Clock and Calendar (RTCC)
Yes
Configurable Logic Cell (CLC)
Resets (and delays)
Instruction Set
Packages
 2013 Microchip Technology Inc.
PIC24F08KM202
PIC24F16KM202
Features
PIC24F08KM204
DEVICE FEATURES FOR THE PIC24F16KM204 FAMILY
PIC24F16KM204
TABLE 1-1:
19
2
POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode,
REPEAT Instruction, Hardware Traps, Configuration Word Mismatch
(PWRT, OST, PLL Lock)
76 Base Instructions, Multiple Addressing Mode Variations
44-Pin QFN/TQFP,
48-Pin UQFN
Advance Information
28-Pin
SPDIP/SSOP/SOIC/QFN
DS33030A-page 15
PIC24FV16KM204 FAMILY
Operating Frequency
DC-32 MHz
Program Memory (bytes)
16K
16K
Program Memory (instructions)
5632
5632
Data Memory (bytes)
8K
8K
2816
2816
1024
Data EEPROM Memory (bytes)
512
Interrupt Sources (soft vectors/NMI traps)
25 (21/4)
Voltage Range
1.8-3.6V
I/O Ports
Total I/O Pins
Timers
PIC24F08KM101
PIC24F08KM102
Features
PIC24F16KM102
DEVICE FEATURES FOR THE PIC24F16KM104 FAMILY
PIC24F16KM104
TABLE 1-2:
PORTA<11:0>
PORTB<15:0>
PORTC<9:0>
PORTA<7:0>
PORTB<15:0>
PORTA<6:0>
PORTB<15:12,9:7,
4,2:0>
38
24
18
5
(One 16-Bit Timer, two MCCP/SCCP with up to two 16/32 timers each)
Capture/Compare/PWM modules
MCCP
SCCP
1
1
Serial Communications
MSSP
UART
1
1
Input Change Notification Interrupt
37
23
17
12-Bit Analog-to-Digital Module
(input channels)
22
19
16
Analog Comparators
1
8-Bit Digital-to-Analog Converters
—
Operational Amplifiers
—
Charge Time Measurement Unit (CTMU)
Yes
Real-Time Clock and Calendar (RTCC)
—
Configurable Logic Cell (CLC)
1
Resets (and delays)
Instruction Set
Packages
DS33030A-page 16
POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode,
REPEAT Instruction, Hardware Traps, Configuration Word Mismatch
(PWRT, OST, PLL Lock)
76 Base Instructions, Multiple Addressing Mode Variations
44-Pin
QFN/TQFP,
48-Pin UQFN
28-Pin
SPDIP/SSOP/SOIC/QFN
Advance Information
20-Pin
SOIC/SSOP/SPDIP
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Operating Frequency
PIC24FV08KM202
PIC24FV16KM202
Features
PIC24FV08KM204
DEVICE FEATURES FOR THE PIC24FV16KM204 FAMILY
PIC24FV16KM204
TABLE 1-3:
DC-32 MHz
Program Memory (bytes)
16K
8K
16K
8K
Program Memory (instructions)
5632
2816
5632
2816
Data Memory (bytes)
2048
Data EEPROM Memory (bytes)
512
Interrupt Sources (soft vectors/NMI traps)
40 (36/4)
Voltage Range
2.0-5.5V
I/O Ports
Total I/O Pins
Timers
PORTA<11:7,5:0>
PORTB<15:0>
PORTC<9:0>
PORTA<7,5:0>
PORTB<15:0>
37
23
11
(One 16-Bit Timer, five MCCP/SCCP with up to two 16/32 timers each)
Capture/Compare/PWM modules
MCCP
SCCP
3
2
Serial Communications
MSSP
UART
2
2
Input Change Notification Interrupt
36
22
12-Bit Analog-to-Digital Module
(input channels)
22
19
Analog Comparators
3
8-Bit Digital-to-Analog Converters
2
Operational Amplifiers
2
Charge Time Measurement Unit (CTMU)
Yes
Real-Time Clock and Calendar (RTCC)
Yes
Configurable Logic Cell (CLC)
Resets (and delays)
Instruction Set
Packages
 2013 Microchip Technology Inc.
2
POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode,
REPEAT Instruction, Hardware Traps, Configuration Word Mismatch
(PWRT, OST, PLL Lock)
76 Base Instructions, Multiple Addressing Mode Variations
44-Pin QFN/TQFP,
48-Pin UQFN
Advance Information
28-Pin
SPDIP/SSOP/SOIC/QFN
DS33030A-page 17
PIC24FV16KM204 FAMILY
Operating Frequency
PIC24FV08KM101
PIC24FV08KM102
Features
PIC24FV16KM102
DEVICE FEATURES FOR THE PIC24FV16KM104 FAMILY
PIC24FV16KM104
TABLE 1-4:
DC-32 MHz
Program Memory (bytes)
16K
16K
8K
8K
Program Memory (instructions)
5632
5632
2816
2816
Data Memory (bytes)
1024
Data EEPROM Memory (bytes)
512
Interrupt Sources (soft vectors/NMI traps)
25 (21/4)
Voltage Range
2.0-5.5V
I/O Ports
Total I/O Pins
Timers
PORTA<11:7,5:0>
PORTB<15:0>
PORTC<9:0>
PORTA<7,5:0>
PORTB<15:0>
PORTA<5:0>
PORTB<15:12,9:7,
4,2:0>
37
23
17
5
(One 16-Bit Timer, two MCCP/SCCP with up to two 16/32 timers each)
Capture/Compare/PWM modules
MCCP
SCCP
1
1
Serial Communications
MSSP
UART
1
1
Input Change Notification Interrupt
36
22
16
12-Bit Analog-to-Digital Module
(input channels)
22
19
16
Analog Comparators
1
8-Bit Digital-to-Analog Converters
—
Operational Amplifiers
—
Charge Time Measurement Unit (CTMU)
Yes
Real-Time Clock and Calendar (RTCC)
—
Configurable Logic Cell (CLC)
1
Resets (and delays)
Instruction Set
Packages
DS33030A-page 18
POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode,
REPEAT Instruction, Hardware Traps, Configuration Word Mismatch
(PWRT, OST, PLL Lock)
76 Base Instructions, Multiple Addressing Mode Variations
44-Pin
QFN/TQFP,
48-Pin UQFN
28-Pin
SPDIP/SSOP/SOIC/QFN
Advance Information
20-Pin
SOIC/SSOP/SPDIP
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 1-1:
PIC24FV16KM204 FAMILY GENERAL BLOCK DIAGRAMS
Data Bus
Interrupt
Controller
16
16
8
16
Data Latch
PSV and Table
Data Access
Control Block
Data RAM
PCL
PCH
Program Counter
Repeat
Stack
Control
Control
Logic
Logic
23
Address
Latch
PORTA(1)
RA<0:7>
16
23
16
Read AGU
Write AGU
Address Latch
Program Memory
PORTB(1)
Data EEPROM
RB<0:15>
Data Latch
16
EA MUX
Literal Data
Address Bus
24
Inst Latch
16
16
PORTC(1)
RC<9:0>
Inst Register
Instruction
Decode and
Control
Control Signals
Timing
OSCO/CLKO
OSCI/CLKI Generation
FRC/LPRC
Oscillators
Precision
Band Gap
Reference
Divide
Support
17x17
Multiplier
Power-up
Timer
16 x 16
W Reg Array
Oscillator
Start-up Timer
Power-on
Reset
16-Bit ALU
16
Watchdog
Timer
DSWDT
Voltage
Regulator
VCAP
HLVD
Note 1:
BOR
VDD, VSS
MCLR
RTCC
Timer1
MCCP1-3
SCCP4/5
CTMU
12-Bit
A/D
Comparators
REFO
Op Amp
1/2
DAC1/2
CN1-36(1)
MSSP1/2
(I2C™, SPI)
CLC1/2
UART1/2
All pins or features are not implemented on all device pinout configurations. See Table 1-5 for I/O port
pin descriptions.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 19
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION
F
FV
Pin Number
Pin Number
Advance Information
I/O
Buffer
21
I
ANA
22
I
ANA
A/D Analog Inputs
21
23
I
ANA
A/D Analog Inputs
2
22
24
I
ANA
A/D Analog Inputs
3
23
25
I
ANA
A/D Analog Inputs
7
4
24
26
I
ANA
A/D Analog Inputs
—
—
—
25
27
I
ANA
A/D Analog Inputs
28
—
—
—
26
28
I
ANA
A/D Analog Inputs
27
29
—
—
—
27
29
I
ANA
A/D Analog Inputs
23
15
16
18
26
23
15
16
I
ANA
A/D Analog Inputs
25
22
14
15
17
25
22
14
15
I
ANA
A/D Analog Inputs
24
21
11
12
16
24
21
11
12
I
ANA
A/D Analog Inputs
23
20
10
11
15
23
20
10
11
I
ANA
A/D Analog Inputs
7
9
6
30
33
7
9
6
30
33
I
ANA
A/D Analog Inputs
8
10
7
31
34
8
10
7
31
34
I
ANA
A/D Analog Inputs
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
AN0
2
2
27
19
21
2
2
27
19
AN1
3
3
28
20
22
3
3
28
20
AN2
4
4
1
21
23
4
4
1
AN3
5
5
2
22
24
5
5
AN4
6
6
3
23
25
6
6
AN5
—
7
4
24
26
—
AN6
—
—
—
25
27
AN7
—
—
—
26
AN8
—
—
—
AN9
18
26
AN10
17
AN11
16
AN12
15
AN13
AN14
Description
A/D Analog Inputs
AN15
9
11
8
33
36
9
11
8
33
36
I
ANA
A/D Analog Inputs
AN16
10
12
9
34
37
10
12
9
34
37
I
ANA
A/D Analog Inputs
AN17
—
14
11
41
45
—
14
11
41
45
I
ANA
A/D Analog Inputs
AN18
—
15
12
42
46
—
15
12
42
46
I
ANA
A/D Analog Inputs
 2013 Microchip Technology Inc.
AN19
11
16
13
43
47
11
16
13
43
47
I
ANA
A/D Analog Inputs
AN20
12
17
14
44
48
12
17
14
44
48
I
ANA
A/D Analog Inputs
AN21
13
18
15
1
1
13
18
15
1
1
I
ANA
A/D Analog Inputs
ASCL1
—
15
12
42
46
—
15
12
42
46
I/O
I2C™
Alternate I2C1 Clock Input/Output
ASDA1
—
14
11
41
45
—
14
11
41
45
I/O
I 2C
Alternate I2C1 Data Input/Output
AVDD
20
28
25
17
18
20
28
25
17
18
P
—
A/D Supply Pins
AVSS
19
27
24
16
17
19
27
24
16
17
P
—
A/D Supply Pins
C1INA
8
7
4
24
26
8
7
4
24
26
I
ANA
Comparator 1 Input A (+)
C1INB
7
6
3
23
25
7
6
3
23
25
I
ANA
Comparator 1 Input B (-)
C1INC
5
5
2
22
24
5
5
2
22
24
I
ANA
Comparator 1 Input C (+)
C1IND
4
4
1
21
23
4
4
1
21
23
I
ANA
Comparator 1 Input D (-)
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
PIC24FV16KM204 FAMILY
DS33030A-page 20
TABLE 1-5:
 2013 Microchip Technology Inc.
TABLE 1-5:
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
F
FV
Pin Number
Pin Number
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
C1OUT
17
25
22
C2INA
—
5
2
C2INB
—
4
C2INC
—
C2IND
—
C2OUT
I/O
Buffer
Description
DS33030A-page 21
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
14
15
17
25
22
14
15
O
—
22
24
—
5
2
22
24
I
ANA
Comparator 2 Input A (+)
1
21
23
—
4
1
21
23
I
ANA
Comparator 2 Input B (-)
7
4
24
26
—
7
4
24
26
I
ANA
Comparator 2 Input C (+)
6
3
23
25
—
6
3
23
25
I
ANA
—
20
17
7
7
—
16
13
43
47
O
—
C3INA
—
26
23
15
16
—
26
23
15
16
I
ANA
Comparator 3 Input A (+)
C3INB
—
25
22
14
15
—
25
22
14
15
I
ANA
Comparator 3 Input B (-)
C3INC
—
2
27
19
21
—
2
27
19
21
I
ANA
Comparator 3 Input C (+)
C3IND
—
4
1
21
23
—
4
1
21
23
I
ANA
C3OUT
—
17
14
44
48
—
17
14
44
48
O
—
Comparator 3 Output
CLC1O
13
18
15
1
1
13
18
15
1
1
O
—
CLC 1 Output
CLC2O
—
19
16
6
6
—
19
16
6
6
O
—
CLC 2 Output
CLCINA
9
14
11
41
45
9
14
11
41
45
I
ST
CLC External Input A
CLCINB
10
15
12
42
46
10
15
12
42
46
I
ST
CLC External Input B
CLKI
7
9
6
30
33
7
9
6
30
33
I
ANA
CLKO
8
10
7
31
34
8
10
7
31
34
O
—
System Clock Output
CN0
10
12
9
34
37
10
12
9
34
37
I
ST
Interrupt-on-Change Inputs
CN1
9
11
8
33
36
9
11
8
33
36
I
ST
Interrupt-on-Change Inputs
CN2
2
2
27
19
21
2
2
27
19
21
I
ST
Interrupt-on-Change Inputs
CN3
3
3
28
20
22
3
3
28
20
22
I
ST
Interrupt-on-Change Inputs
CN4
4
4
1
21
23
4
4
1
21
23
I
ST
Interrupt-on-Change Inputs
CN5
5
5
2
22
24
5
5
2
22
24
I
ST
Interrupt-on-Change Inputs
CN6
6
6
3
23
25
6
6
3
23
25
I
ST
Interrupt-on-Change Inputs
CN7
—
7
4
24
26
—
7
4
24
26
I
ST
Interrupt-on-Change Inputs
CN8
14
20
17
7
7
—
—
—
—
—
I
ST
Interrupt-on-Change Inputs
CN9
—
19
16
6
6
—
19
16
6
6
I
ST
Interrupt-on-Change Inputs
CN10
—
—
—
27
29
—
—
—
27
29
I
ST
Interrupt-on-Change Inputs
44-Pin
QFN/
TQFP
48-Pin
UQFN
Comparator 1 Output
Comparator 2 Input D (-)
Comparator 2 Output
Comparator 3 Input D (-)
Primary Clock Input
CN11
18
26
23
15
16
18
26
23
15
16
I
ST
Interrupt-on-Change Inputs
CN12
17
25
22
14
15
17
25
22
14
15
I
ST
Interrupt-on-Change Inputs
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
PIC24FV16KM204 FAMILY
Advance Information
48-Pin
UQFN
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
F
FV
Pin Number
Pin Number
Advance Information
I/O
Buffer
12
I
ST
Interrupt-on-Change Inputs
11
I
ST
Interrupt-on-Change Inputs
9
10
I
ST
Interrupt-on-Change Inputs
18
8
9
I
ST
Interrupt-on-Change Inputs
—
—
3
3
I
ST
Interrupt-on-Change Inputs
—
—
—
2
2
I
ST
Interrupt-on-Change Inputs
5
—
—
—
5
5
I
ST
Interrupt-on-Change Inputs
4
4
—
—
—
4
4
I
ST
Interrupt-on-Change Inputs
15
1
1
13
18
15
1
1
I
ST
Interrupt-on-Change Inputs
17
14
44
48
12
17
14
44
48
I
ST
Interrupt-on-Change Inputs
16
13
43
47
11
16
13
43
47
I
ST
Interrupt-on-Change Inputs
—
15
12
42
46
—
15
12
42
46
I
ST
Interrupt-on-Change Inputs
CN25
—
—
—
37
40
—
—
—
37
40
I
ST
Interrupt-on-Change Inputs
CN26
—
—
—
38
41
—
—
—
38
41
I
ST
Interrupt-on-Change Inputs
CN27
—
14
11
41
45
—
14
11
41
45
I
ST
Interrupt-on-Change Inputs
CN28
—
—
—
36
39
—
—
—
36
39
I
ST
Interrupt-on-Change Inputs
CN29
8
10
7
31
34
8
10
7
31
34
I
ST
Interrupt-on-Change Inputs
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
CN13
16
24
CN14
15
23
CN15
—
CN16
44-Pin
QFN/
TQFP
48-Pin
UQFN
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
21
11
12
16
24
20
10
11
15
23
22
19
9
10
—
—
21
18
8
9
CN17
—
—
—
3
CN18
—
—
—
CN19
—
—
CN20
—
CN21
44-Pin
QFN/
TQFP
48-Pin
UQFN
21
11
20
10
22
19
—
21
3
—
2
2
—
5
—
—
13
18
CN22
12
CN23
11
CN24
Description
 2013 Microchip Technology Inc.
CN30
7
9
6
30
33
7
9
6
30
33
I
ST
Interrupt-on-Change Inputs
CN31
—
—
—
26
28
—
—
—
26
28
I
ST
Interrupt-on-Change Inputs
CN32
—
—
—
25
27
—
—
—
25
27
I
ST
Interrupt-on-Change Inputs
CN33
—
—
—
32
35
—
—
—
32
35
I
ST
Interrupt-on-Change Inputs
CN34
—
—
—
35
38
—
—
—
35
38
I
ST
Interrupt-on-Change Inputs
CN35
—
—
—
12
13
—
—
—
12
13
I
ST
Interrupt-on-Change Inputs
CN36
—
—
—
13
14
—
—
—
13
14
I
ST
Interrupt-on-Change Inputs
CTCMP
4
4
1
21
23
4
4
1
21
23
I
ANA
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
CTMU Comparator Input
PIC24FV16KM204 FAMILY
DS33030A-page 22
TABLE 1-5:
 2013 Microchip Technology Inc.
TABLE 1-5:
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
F
FV
Pin Number
Pin Number
I/O
Buffer
Description
21
I
ST
11
I
ST
CTMU Trigger Edge Inputs
6
I
ST
CTMU Trigger Edge Inputs
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
CTED1
11
20
17
7
7
11
2
CTED2
15
23
20
10
11
15
23
CTED3
—
19
16
6
6
—
19
16
CTED4
13
18
15
1
1
13
18
15
1
1
I
ST
CTMU Trigger Edge Inputs
CTED5
17
25
22
14
15
17
25
22
14
15
I
ST
CTMU Trigger Edge Inputs
CTED6
18
26
23
15
16
18
26
23
15
16
I
ST
CTMU Trigger Edge Inputs
CTED7
—
—
—
5
5
—
—
—
5
5
I
ST
CTMU Trigger Edge Inputs
CTED8
—
—
—
13
14
—
—
—
13
14
I
ST
CTMU Trigger Edge Inputs
44-Pin
QFN/
TQFP
48-Pin
UQFN
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
44-Pin
QFN/
TQFP
48-Pin
UQFN
27
19
20
10
6
28-Pin
QFN
CTMU Trigger Edge Inputs
CTED9
—
22
19
9
10
—
22
19
9
10
I
ST
CTMU Trigger Edge Inputs
CTED10
12
17
14
44
48
12
17
14
44
48
I
ST
CTMU Trigger Edge Inputs
CTED11
—
21
18
8
9
—
21
18
8
9
I
ST
CTMU Trigger Edge Inputs
CTED12
5
5
2
22
24
5
5
2
22
24
I
ST
CTMU Trigger Edge Inputs
CTMU Trigger Edge Inputs
DS33030A-page 23
CTED13
6
6
3
23
25
6
6
3
23
25
I
ST
CTPLS
16
24
21
11
12
16
24
21
11
12
O
—
CVREF
17
25
22
14
15
17
25
22
14
15
O
ANA
Comparator Voltage Reference Output
CVREF+
2
2
27
19
21
2
2
27
19
21
I
ANA
Comparator Voltage Reference Positive Input
CVREF-
3
3
28
20
22
3
3
28
20
22
I
ANA
Comparator Voltage Reference Negative Input
DAC1OUT
—
23
20
10
11
—
23
20
10
11
O
ANA
DAC1 Output
DAC1REF+
—
2
27
19
21
—
2
27
19
21
I
ANA
DAC1 Positive Voltage Reference Input
DAC2OUT
—
25
22
14
15
—
25
22
14
15
O
ANA
DAC2 Output
DAC2REF+
—
26
23
15
16
—
26
23
15
16
I
ANA
DAC2 Positive Voltage Reference Input
HLVDIN
15
23
20
10
11
15
23
20
10
11
I
ANA
External High/Low-Voltage Detect Input
IC1
14
19
16
6
6
11
19
16
6
6
I
ST
IC2
13
18
15
1
1
13
18
15
1
1
I
ST
MCCP2 Input Capture Input
IC3
—
23
20
13
14
—
23
20
13
14
I
ST
MCCP3 Input Capture Input
IC4
—
14
11
5
5
—
14
11
5
5
I
ST
SCCP4 Input Capture Input
IC5
—
15
12
12
13
—
15
12
12
13
I
ST
SCCP5 Input Capture Input
CTMU Pulse Output
MCCP1 Input Capture Input
INT0
11
16
13
43
47
11
16
13
43
47
I
ST
External Interrupt 0 Input
INT1
17
25
22
14
15
17
25
22
14
15
I
ST
External Interrupt 1 Input
14
20
17
7
7
15
23
20
10
11
I
ST
External Interrupt 2 Input
INT2
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
PIC24FV16KM204 FAMILY
Advance Information
20-Pin
PDIP/
SSOP/
SOIC
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
20-Pin
PDIP/
SSOP/
SOIC
F
FV
Pin Number
Pin Number
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
I/O
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
Buffer
Description
Master Clear (Device Reset) Input (active-low)
Advance Information
MCLR
1
1
26
18
19
1
1
26
18
19
I
ST
OA1INA
—
5
2
22
24
—
5
2
22
24
I
ANA
OA1INB
—
6
3
23
25
—
6
3
23
25
I
ANA
Op Amp 1 Input B
OA1INC
—
24
21
11
12
—
24
21
11
12
I
ANA
Op Amp 1 Input C
OA1IND
—
25
22
14
15
—
25
22
14
15
I
ANA
Op Amp 1 Input D
OA1OUT
—
7
4
24
26
—
7
4
24
26
O
ANA
Op Amp 1 Analog Output
OA2INA
—
5
2
22
24
—
5
2
22
24
I
ANA
Op Amp 2 Input A
OA2INB
—
6
3
23
25
—
6
3
23
25
I
ANA
Op Amp 2 Input B
OA2INC
—
24
21
11
12
—
24
21
11
12
I
ANA
Op Amp 2 Input C
OA2IND
—
25
22
14
15
—
25
22
14
15
I
ANA
Op Amp 2 Input D
OA2OUT
—
26
23
15
16
—
26
23
15
16
O
ANA
OC1A
14
20
17
7
7
11
16
13
43
47
O
—
MCCP1 Output Compare A
MCCP1 Output Compare B
Op Amp 1 Input A
Op Amp 2 Analog Output
OC1B
12
17
14
44
48
12
17
14
44
48
O
—
OC1C
15
21
18
8
9
15
21
18
8
9
O
—
MCCP1 Output Compare C
OC1D
16
24
21
11
12
16
24
21
11
12
O
—
MCCP1 Output Compare D
OC1E
—
14
11
41
45
—
14
11
41
45
O
—
MCCP1 Output Compare E
OC1F
—
15
12
42
46
—
15
12
42
46
O
—
MCCP1 Output Compare F
 2013 Microchip Technology Inc.
OC2A
4
22
19
9
10
4
22
19
9
10
O
—
MCCP2 Output Compare A
OC2B
—
23
20
10
11
—
23
20
10
11
O
—
MCCP2 Output Compare B
OC2C
—
—
—
2
2
—
—
—
2
2
O
—
MCCP2 Output Compare C
OC2D
—
—
—
3
3
—
—
—
3
3
O
—
MCCP2 Output Compare D
OC2E
—
—
—
4
4
—
—
—
4
4
O
—
MCCP2 Output Compare E
OC2F
—
—
—
5
5
—
—
—
5
5
O
—
MCCP2 Output Compare F
OC3A
—
21
18
12
13
—
21
18
12
13
O
—
MCCP3 Output Compare A
OC3B
—
24
21
13
14
—
24
21
13
14
O
—
MCCP3 Output Compare B
OC4
—
18
15
1
1
—
18
15
1
1
O
—
SCCP4 Output Compare
OC5
—
19
16
6
6
—
19
16
6
6
O
—
SCCP5 Output Compare
OCFA
17
25
22
14
15
17
25
22
14
15
I
ST
MCCP/SCCP Output Compare Fault Input A
16
24
21
32
35
16
24
21
32
35
I
ST
MCCP/SCCP Output Compare Fault Input B
OCFB
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
PIC24FV16KM204 FAMILY
DS33030A-page 24
TABLE 1-5:
 2013 Microchip Technology Inc.
TABLE 1-5:
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
20-Pin
PDIP/
SSOP/
SOIC
F
FV
Pin Number
Pin Number
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
20-Pin
PDIP/
SSOP/
SOIC
I/O
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
Buffer
Description
OSCI
7
9
6
30
33
7
9
6
30
33
I
ANA
Primary Oscillator Input
OSCO
8
10
7
31
34
8
10
7
31
34
O
ANA
Primary Oscillator Output
PGC1
5
5
2
22
24
5
5
2
22
24
I/O
ST
PGD1
4
4
1
21
23
4
4
1
21
23
I/O
ST
ICSP Data 1
PGC2
2
22
19
9
10
2
22
19
9
10
I/O
ST
ICSP Clock 2
ICSP Clock 1
PGD2
3
21
18
8
9
3
21
18
8
9
I/O
ST
ICSP Data 2
PGC3
10
15
12
42
46
10
15
12
42
46
I/O
ST
ICSP Clock 3
DS33030A-page 25
9
14
11
41
45
9
14
11
41
45
I/O
ST
ICSP Data 3
PWRLCLK
10
12
9
34
37
10
12
9
34
37
I
ST
RTCC Power Line Clock Input
RA0
2
2
27
19
21
2
2
27
19
21
I/O
ST
PORTA Pins
RA1
3
3
28
20
22
3
3
28
20
22
I/O
ST
PORTA Pins
RA2
7
9
6
30
33
7
9
6
30
33
I/O
ST
PORTA Pins
RA3
8
10
7
31
34
8
10
7
31
34
I/O
ST
PORTA Pins
RA4
10
12
9
34
37
10
12
9
34
37
I/O
ST
PORTA Pins
RA5
1
1
26
18
19
1
1
26
18
19
I/O
ST
PORTA Pins
RA6
14
20
17
7
7
—
—
—
—
—
I/O
ST
PORTA Pins
RA7
—
19
16
6
6
—
19
16
6
6
I/O
ST
PORTA Pins
RA8
—
—
—
32
35
—
—
—
32
35
I/O
ST
PORTA Pins
RA9
—
—
—
35
38
—
—
—
35
38
I/O
ST
PORTA Pins
RA10
—
—
—
12
13
—
—
—
12
13
I/O
ST
PORTA Pins
RA11
—
—
—
13
14
—
—
—
13
14
I/O
ST
PORTA Pins
RB0
4
4
1
21
23
4
4
1
21
23
I/O
ST
PORTB Pins
RB1
5
5
2
22
24
5
5
2
22
24
I/O
ST
PORTB Pins
RB2
6
6
3
23
25
6
6
3
23
25
I/O
ST
PORTB Pins
RB3
—
7
4
24
26
—
7
4
24
26
I/O
ST
PORTB Pins
RB4
9
11
8
33
36
9
11
8
33
36
I/O
ST
PORTB Pins
RB5
—
14
11
41
45
—
14
11
41
45
I/O
ST
PORTB Pins
RB6
—
15
12
42
46
—
15
12
42
46
I/O
ST
PORTB Pins
RB7
11
16
13
43
47
11
16
13
43
47
I/O
ST
PORTB Pins
RB8
12
17
14
44
48
12
17
14
44
48
I/O
ST
PORTB Pins
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
PIC24FV16KM204 FAMILY
Advance Information
PGD3
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
F
FV
Pin Number
Pin Number
I/O
Buffer
Description
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
RB9
13
18
15
1
1
13
18
15
1
1
I/O
ST
PORTB Pins
RB10
—
21
18
8
9
—
21
18
8
9
I/O
ST
PORTB Pins
Advance Information
 2013 Microchip Technology Inc.
RB11
—
22
19
9
10
—
22
19
9
10
I/O
ST
PORTB Pins
RB12
15
23
20
10
11
15
23
20
10
11
I/O
ST
PORTB Pins
RB13
16
24
21
11
12
16
24
21
11
12
I/O
ST
PORTB Pins
RB14
17
25
22
14
15
17
25
22
14
15
I/O
ST
PORTB Pins
RB15
18
26
23
15
16
18
26
23
15
16
I/O
ST
PORTB Pins
RC0
—
—
—
25
27
—
—
—
25
27
I/O
ST
PORTC Pins
RC1
—
—
—
26
28
—
—
—
26
28
I/O
ST
PORTC Pins
RC2
—
—
—
27
29
—
—
—
27
29
I/O
ST
PORTC Pins
RC3
—
—
—
36
39
—
—
—
36
39
I/O
ST
PORTC Pins
RC4
—
—
—
37
40
—
—
—
37
40
I/O
ST
PORTC Pins
RC5
—
—
—
38
41
—
—
—
38
41
I/O
ST
PORTC Pins
RC6
—
—
—
2
2
—
—
—
2
2
I/O
ST
PORTC Pins
RC7
—
—
—
3
3
—
—
—
3
3
I/O
ST
PORTC Pins
RC8
—
—
—
4
4
—
—
—
4
4
I/O
ST
PORTC Pins
RC9
—
—
—
5
5
—
—
—
5
5
I/O
ST
PORTC Pins
REFO
18
26
23
15
16
18
26
23
15
16
O
—
Reference Clock Output
RTCC
—
25
22
14
15
—
25
22
14
15
O
—
Real-Time Clock/Calendar Output
SCK1
15
22
19
9
10
15
22
19
9
10
I/O
ST
MSSP1 SPI Clock
SDI1
17
21
18
8
9
17
21
18
8
9
I
ST
MSSP1 SPI Data Input
SDO1
16
24
21
11
12
16
24
21
11
12
O
—
MSSP1 SPI Data Output
SS1
18
26
23
15
16
18
26
23
15
16
I
ST
MSSP1 SPI Slave Select Input
SCK2
—
14
11
38
41
—
14
11
38
41
I/O
ST
MSSP2 SPI Clock
SDI2
—
19
16
36
39
—
19
16
36
39
I
ST
MSSP2 SPI Data Input
SDO2
—
15
12
37
40
—
15
12
37
40
O
—
MSSP2 SPI Data Output
SS2
—
23
20
35
38
—
23
20
35
38
I
ST
MSSP2 SPI Slave Select Input
Legend:
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
PIC24FV16KM204 FAMILY
DS33030A-page 26
TABLE 1-5:
 2013 Microchip Technology Inc.
TABLE 1-5:
Function
PIC24FV16KM204 FAMILY PINOUT DESCRIPTION (CONTINUED)
F
FV
Pin Number
Pin Number
I/O
Buffer
48
I/O
I2C
1
I/O
I2C
MSSP1 I2C Data
26
I/O
I2C
MSSP2 I2C Clock
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
20-Pin
PDIP/
SSOP/
SOIC
28-Pin
PDIP/
SSOP/
SOIC
28-Pin
QFN
44-Pin
QFN/
TQFP
48-Pin
UQFN
SCL1
12
17
14
44
48
12
17
14
44
SDA1
13
18
15
1
1
13
18
15
1
SCL2
—
7
4
24
26
—
7
4
24
Description
MSSP1 I2C Clock
—
6
3
23
25
—
6
3
23
25
I/O
I2C
MSSP2 I2C Data
SCLKI
10
12
9
34
37
10
12
9
34
37
I
ST
Secondary Clock Digital Input
SOSCI
9
11
8
33
36
9
11
8
33
36
I
ANA
Secondary Oscillator Input
SOSCO
10
12
9
34
37
10
12
9
34
37
I
ANA
Secondary Oscillator Output
T1CK
13
18
15
1
1
13
18
15
1
1
I
ST
Timer1 Digital Input Cock
TCKIA
18
26
23
15
16
18
26
23
15
16
I
ST
MCCP/SCCP Time Base Clock Input A
TCKIB
6
6
3
23
25
6
6
3
23
25
I
ST
MCCP/SCCP Time Base Clock Input B
U1CTSN
12
17
14
44
48
12
17
14
44
48
I
ST
UART1 Clear-to-Send Input
U1RTS
13
18
15
1
1
13
18
15
1
1
O
—
UART1 Request-to-Send Output
U1BCLK
13
18
15
1
1
13
18
15
1
1
O
—
UART1 16x Baud Rate Clock Output
U1RX
6
6
3
2
2
6
6
3
2
2
I
ST
UART1 Receive
U1TX
11
16
13
3
3
11
16
13
3
3
O
—
UART1 Transmit
U2CTSN
-
12
9
34
37
-
12
9
34
37
I
ST
UART2 Clear-to-Send Input
U2RTS
-
11
8
33
36
-
11
8
33
36
O
-
UART2 Request-to-Send Output
13
18
15
1
1
13
18
15
1
1
O
-
UART2 16x Baud Rate Clock Output
U2RX
-
5
2
22
24
-
5
2
22
24
I
ST
UART2 Receive
U2TX
-
4
1
21
23
-
4
1
21
23
O
-
UART2 Transmit
ULPWU
4
4
1
21
23
4
4
1
21
23
I
ANA
VCAP
-
-
-
-
-
14
20
17
7
7
P
-
Regulator External Filter Capacitor Connection
20
28
25
20
28
25
P
-
Device Positive Supply Voltage
U2BCLK
VDD
17,28,28 18,30,30
17,28,28 18,30,30
Ultra Low-Power Wake-up Input
VDDCORE
-
-
-
-
-
14
20
17
7
7
P
-
Microcontroller Core Supply Voltage
VPP
1
1
26
18
19
1
1
26
18
19
P
-
High-Voltage Programming Pin
DS33030A-page 27
VREF+
2
2
27
19
21
2
2
27
19
21
I
ANA
VREF-
3
3
28
20
22
3
3
28
20
22
I
ANA
VSS
19
27
24
19
27
24
P
-
Legend:
16,29,29 17,31,31
16,29,29 17,31,31
ANA = Analog level input/output, ST = Schmitt Trigger input buffer, I2C™ = I2C/SMBus input buffer
A/D Reference Voltage Positive Input
A/D Reference Voltage Negative Input
Device Ground Return Voltage
PIC24FV16KM204 FAMILY
Advance Information
SDA2
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 28
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
• All VDD and VSS pins
(see Section 2.2 “Power Supply Pins”)
• All AVDD and AVSS pins, regardless of whether or
not the analog device features are used
(see Section 2.2 “Power Supply Pins”)
• MCLR pin
(see Section 2.3 “Master Clear (MCLR) Pin”)
• VCAP pins
(see Section 2.4 “Voltage Regulator Pin (VCAP)”)
R1
R2
VSS
VDD
MCLR
VCAP
C1
C7
PIC24FV16KM204
C6(2)
VSS
VDD
VDD
VSS
C3(2)
C5(2)
C4(2)
These pins must also be connected if they are being
used in the end application:
Key (all values are recommendations):
• PGECx/PGEDx pins used for In-Circuit Serial
Programming™ (ICSP™) and debugging purposes
(see Section 2.5 “ICSP Pins”)
• OSCI and OSCO pins when an external oscillator
source is used
(see Section 2.6 “External Oscillator Pins”)
C7: 10 µF, 16V tantalum or ceramic
Additionally, the following pins may be required:
C1 through C6: 0.1 µF, 20V ceramic
R1: 10 kΩ
R2: 100Ω to 470Ω
Note 1:
2:
• VREF+/VREF- pins are used when external voltage
reference for analog modules is implemented
Note:
(1)
VSS
The following pins must always be connected:
C2(2)
VDD
Getting started with the PIC24FV16KM204 family of
16-bit microcontrollers requires attention to a minimal
set of device pin connections before proceeding with
development.
RECOMMENDED
MINIMUM CONNECTIONS
VDD
Basic Connection Requirements
FIGURE 2-1:
AVSS
2.1
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
MICROCONTROLLERS
AVDD
2.0
The AVDD and AVSS pins must always be
connected, regardless of whether any of
the analog modules are being used.
See Section 2.4 “Voltage Regulator Pin
(VCAP)” for an explanation of VCAP pin
connections.
The example shown is for a PIC24F device
with five VDD/VSS and AVDD/AVSS pairs.
Other devices may have more or less
pairs; adjust the number of decoupling
capacitors appropriately.
The minimum mandatory connections are shown in
Figure 2-1.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 29
PIC24FV16KM204 FAMILY
2.2
2.2.1
Power Supply Pins
2.3
DECOUPLING CAPACITORS
The use of decoupling capacitors on every pair of
power supply pins, such as VDD, VSS, AVDD and
AVSS, is required.
Consider the following criteria when using decoupling
capacitors:
• Value and type of capacitor: A 0.1 µF (100 nF),
10-20V capacitor is recommended. The capacitor
should be a low-ESR device, with a resonance
frequency in the range of 200 MHz and higher.
Ceramic capacitors are recommended.
• Placement on the printed circuit board: The
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is no greater
than 0.25 inch (6 mm).
• Handling high-frequency noise: If the board is
experiencing high-frequency noise (upward of
tens of MHz), add a second ceramic type capacitor in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 µF to 0.001 µF. Place this
second capacitor next to each primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible
(e.g., 0.1 µF in parallel with 0.001 µF).
• Maximizing performance: On the board layout
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum, thereby reducing PCB trace
inductance.
2.2.2
TANK CAPACITORS
On boards with power traces running longer than
six inches in length, it is suggested to use a tank capacitor for integrated circuits, including microcontrollers, to
supply a local power source. The value of the tank
capacitor should be determined based on the trace
resistance that connects the power supply source to
the device, and the maximum current drawn by the
device in the application. In other words, select the tank
capacitor so that it meets the acceptable voltage sag at
the device. Typical values range from 4.7 µF to 47 µF.
DS33030A-page 30
Master Clear (MCLR) Pin
The MCLR pin provides two specific device
functions: device Reset, and device programming
and debugging. If programming and debugging are
not required in the end application, a direct
connection to VDD may be all that is required. The
addition of other components, to help increase the
application’s resistance to spurious Resets from
voltage sags, may be beneficial. A typical
configuration is shown in Figure 2-1. Other circuit
designs may be implemented, depending on the
application’s requirements.
During programming and debugging, the resistance
and capacitance that can be added to the pin must
be considered. Device programmers and debuggers
drive the MCLR pin. Consequently, specific voltage
levels (VIH and VIL) and fast signal transitions must
not be adversely affected. Therefore, specific values
of R1 and C1 will need to be adjusted based on the
application and PCB requirements. For example, it is
recommended that the capacitor, C1, be isolated
from the MCLR pin during programming and
debugging operations by using a jumper (Figure 2-2).
The jumper is replaced for normal run-time
operations.
Any components associated with the MCLR pin
should be placed within 0.25 inch (6 mm) of the pin.
FIGURE 2-2:
EXAMPLE OF MCLR PIN
CONNECTIONS
VDD
R1
R2
JP
MCLR
PIC24FXXKXX
C1
Note 1:
R1  10 k is recommended. A suggested
starting value is 10 k. Ensure that the
MCLR pin VIH and VIL specifications are met.
2:
R2  470 will limit any current flowing into
MCLR from the external capacitor, C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
VIH and VIL specifications are met.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Voltage Regulator Pin (VCAP)
Note:
This
section
applies
only
to
PIC24FV16KM devices with an on-chip
voltage regulator.
Refer to Section 27.0 “Electrical Characteristics” for
information on VDD and VDDCORE.
FIGURE 2-3:
Some of the PIC24FV16KM devices have an internal
voltage regulator. These devices have the voltage
regulator output brought out on the VCAP pin. On the
PIC24F K devices with regulators, a low-ESR (< 5Ω)
capacitor is required on the VCAP pin to stabilize the
voltage regulator output. The VCAP pin must not be
connected to VDD and must use a capacitor of 10 µF
connected to ground. The type can be ceramic or
tantalum. Suitable examples of capacitors are shown in
Table 2-1. Capacitors with equivalent specifications can
be used.
Designers may use Figure 2-3 to evaluate ESR
equivalence of candidate devices.
The placement of this capacitor should be close to VCAP.
It is recommended that the trace length not exceed
0.25 inch (6 mm). Refer to Section 27.0 “Electrical
Characteristics” for additional information.
TABLE 2-1:
FREQUENCY vs. ESR
PERFORMANCE FOR
SUGGESTED VCAP
10
1
ESR ()
2.4
0.1
0.01
0.001
0.01
Note:
0.1
1
10
100
Frequency (MHz)
1000 10,000
Typical data measurement at 25°C, 0V DC bias.
SUITABLE CAPACITOR EQUIVALENTS
Make
Part #
Nominal
Capacitance
Base Tolerance
Rated Voltage
Temp. Range
TDK
C3216X7R1C106K
10 µF
±10%
16V
-55 to +125ºC
TDK
C3216X5R1C106K
10 µF
±10%
16V
-55 to +85ºC
Panasonic
ECJ-3YX1C106K
10 µF
±10%
16V
-55 to +125ºC
Panasonic
ECJ-4YB1C106K
10 µF
±10%
16V
-55 to +85ºC
Murata
GRM32DR71C106KA01L
10 µF
±10%
16V
-55 to +125ºC
Murata
GRM31CR61C106KC31L
10 µF
±10%
16V
-55 to +85ºC
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 31
PIC24FV16KM204 FAMILY
CONSIDERATIONS FOR CERAMIC
CAPACITORS
In recent years, large value, low-voltage, surface-mount
ceramic capacitors have become very cost effective in
sizes up to a few tens of microfarad. The low-ESR, small
physical size and other properties make ceramic
capacitors very attractive in many types of applications.
Ceramic capacitors are suitable for use with the internal voltage regulator of this microcontroller. However,
some care is needed in selecting the capacitor to
ensure that it maintains sufficient capacitance over the
intended operating range of the application.
Typical low-cost, 10 µF ceramic capacitors are available
in X5R, X7R and Y5V dielectric ratings (other types are
also available, but are less common). The initial tolerance specifications for these types of capacitors are
often specified as ±10% to ±20% (X5R and X7R), or
-20%/+80% (Y5V). However, the effective capacitance
that these capacitors provide in an application circuit will
also vary based on additional factors, such as the
applied DC bias voltage and the temperature. The total
in-circuit tolerance is, therefore, much wider than the
initial tolerance specification.
The X5R and X7R capacitors typically exhibit satisfactory temperature stability (ex: ±15% over a wide
temperature range, but consult the manufacturer’s data
sheets for exact specifications). However, Y5V capacitors typically have extreme temperature tolerance
specifications of +22%/-82%. Due to the extreme
temperature tolerance, a 10 µF nominal rated Y5V type
capacitor may not deliver enough total capacitance to
meet minimum internal voltage regulator stability and
transient response requirements. Therefore, Y5V
capacitors are not recommended for use with the
internal regulator if the application must operate over a
wide temperature range.
In addition to temperature tolerance, the effective
capacitance of large value ceramic capacitors can vary
substantially, based on the amount of DC voltage
applied to the capacitor. This effect can be very significant, but is often overlooked or is not always
documented.
A typical DC bias voltage vs. capacitance graph for
X7R type capacitors is shown in Figure 2-4.
FIGURE 2-4:
Capacitance Change (%)
2.4.1
DC BIAS VOLTAGE vs.
CAPACITANCE
CHARACTERISTICS
10
0
-10
16V Capacitor
-20
-30
-40
10V Capacitor
-50
-60
-70
6.3V Capacitor
-80
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
DC Bias Voltage (VDC)
When selecting a ceramic capacitor to be used with the
internal voltage regulator, it is suggested to select a
high-voltage rating, so that the operating voltage is a
small percentage of the maximum rated capacitor voltage. For example, choose a ceramic capacitor rated at
16V for the 3.3V or 2.5V core voltage. Suggested
capacitors are shown in Table 2-1.
2.5
ICSP Pins
The PGC and PGD pins are used for In-Circuit Serial
Programming™ (ICSP™) and debugging purposes. It
is recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recommended, with the value in the range of a few tens of
ohms, not to exceed 100Ω.
Pull-up resistors, series diodes and capacitors on the
PGC and PGD pins are not recommended as they will
interfere with the programmer/debugger communications to the device. If such discrete components are an
application requirement, they should be removed from
the circuit during programming and debugging. Alternatively, refer to the AC/DC characteristics and timing
requirements information in the respective device
Flash programming specification for information on
capacitive loading limits, and pins, Voltage Input High
(VIH) and Voltage Input Low (VIL) requirements.
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGCx/PGDx pins), programmed
into the device, matches the physical connections for
the ICSP to the Microchip debugger/emulator tool.
For more information on available Microchip
development tools connection requirements, refer to
Section 26.0 “Development Support”.
DS33030A-page 32
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
2.6
External Oscillator Pins
FIGURE 2-5:
Many microcontrollers have options for at least two
oscillators: a high-frequency primary oscillator and a
low-frequency secondary oscillator (refer to for
Section 9.0 “Oscillator Configuration”details).
The oscillator circuit should be placed on the same
side of the board as the device. Place the oscillator
circuit close to the respective oscillator pins with no
more than 0.5 inch (12 mm) between the circuit
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side
of the board.
Use a grounded copper pour around the oscillator circuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
traces inside the ground pour. Also, if using a two-sided
board, avoid any traces on the other side of the board
where the crystal is placed.
Single-Sided and In-Line Layouts:
Copper Pour
(tied to ground)
For additional information and design guidance on
oscillator circuits, please refer to these Microchip
Application Notes, available at the corporate web site
(www.microchip.com):
• AN826, “Crystal Oscillator Basics and Crystal
Selection for rfPIC™ and PICmicro® Devices”
• AN849, “Basic PICmicro® Oscillator Design”
• AN943, “Practical PICmicro® Oscillator Analysis
and Design”
• AN949, “Making Your Oscillator Work”
2.7
Unused I/Os
Primary Oscillator
Crystal
DEVICE PINS
Primary
Oscillator
OSC1
C1
`
OSC2
GND
C2
`
T1OSO
T1OS I
Timer1 Oscillator
Crystal
Layout suggestions are shown in Figure 2-5. In-line
packages may be handled with a single-sided layout
that completely encompasses the oscillator pins. With
fine-pitch packages, it is not always possible to completely surround the pins and components. A suitable
solution is to tie the broken guard sections to a mirrored
ground layer. In all cases, the guard trace(s) must be
returned to ground.
In planning the application’s routing and I/O assignments, ensure that adjacent port pins and other
signals, in close proximity to the oscillator, are benign
(i.e., free of high frequencies, short rise and fall times,
and other similar noise).
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
`
T1 Oscillator: C1
T1 Oscillator: C2
Fine-Pitch (Dual-Sided) Layouts:
Top Layer Copper Pour
(tied to ground)
Bottom Layer
Copper Pour
(tied to ground)
OSCO
C2
Oscillator
Crystal
GND
C1
OSCI
DEVICE PINS
Unused I/O pins should be configured as outputs and
driven to a logic low state. Alternatively, connect a 1 kΩ
to 10 kΩ resistor to VSS on unused pins and drive the
output to logic low.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 33
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 34
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
3.0
Note:
CPU
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on the
CPU, refer to the “PIC24F Family
Reference Manual”, Section 2. “CPU”
(DS39703).
The PIC24F CPU has a 16-bit (data) modified Harvard
architecture with an enhanced instruction set and a
24-bit instruction word with a variable length opcode
field. The Program Counter (PC) is 23 bits wide and
addresses up to 4M instructions of user program
memory space. A single-cycle instruction prefetch
mechanism is used to help maintain throughput and
provides predictable execution. All instructions execute
in a single cycle, with the exception of instructions that
change the program flow, the double-word move
(MOV.D) instruction and the table instructions.
Overhead-free program loop constructs are supported
using the REPEAT instructions, which are interruptible
at any point.
PIC24F devices have sixteen, 16-bit working registers
in the programmer’s model. Each of the working
registers can act as a data, address or address offset
register. The 16th working register (W15) operates as a
Software Stack Pointer (SSP) for interrupts and calls.
The upper 32 Kbytes of the data space memory map
can optionally be mapped into program space at any
16K word boundary of either program memory or data
EEPROM memory, defined by the 8-bit Program Space
Visibility Page Address (PSVPAG) register. The
program to data space mapping feature lets any
instruction access program space as if it were data
space.
For most instructions, the core is capable of executing
a data (or program data) memory read, a working
register (data) read, a data memory write and a program (instruction) memory read per instruction cycle.
As a result, three parameter instructions can be
supported, allowing trinary operations (i.e., A + B = C)
to be executed in a single cycle.
A high-speed, 17-bit by 17-bit multiplier has been
included to significantly enhance the core arithmetic
capability and throughput. The multiplier supports
Signed, Unsigned and Mixed mode, 16-bit by 16-bit or
8-bit by 8-bit integer multiplication. All multiply
instructions execute in a single cycle.
The 16-bit ALU has been enhanced with integer divide
assist hardware that supports an iterative non-restoring
divide algorithm. It operates in conjunction with the
REPEAT instruction looping mechanism and a selection
of iterative divide instructions to support 32-bit (or
16-bit), divided by 16-bit integer signed and unsigned
division. All divide operations require 19 cycles to
complete but are interruptible at any cycle boundary.
The PIC24F has a vectored exception scheme with up
to eight sources of non-maskable traps and up to
118 interrupt sources. Each interrupt source can be
assigned to one of seven priority levels.
A block diagram of the CPU is illustrated in Figure 3-1.
3.1
Programmer’s Model
Figure 3-2 displays the programmer’s model for the
PIC24F. All registers in the programmer’s model are
memory mapped and can be manipulated directly by
instructions.
Table 3-1 provides a description of each register. All
registers associated with the programmer’s model are
memory mapped.
The Instruction Set Architecture (ISA) has been significantly enhanced beyond that of the PIC18, but
maintains an acceptable level of backward compatibility. All PIC18 instructions and addressing modes are
supported, either directly, or through simple macros.
Many of the ISA enhancements have been driven by
compiler efficiency needs.
The core supports Inherent (no operand), Relative,
Literal, Memory Direct and three groups of addressing
modes. All modes support Register Direct and various
Register Indirect modes. Each group offers up to seven
addressing modes. Instructions are associated with
predefined addressing modes depending upon their
functional requirements.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 35
PIC24FV16KM204 FAMILY
FIGURE 3-1:
PIC24F CPU CORE BLOCK DIAGRAM
PSV and Table
Data Access
Control Block
Data Bus
Interrupt
Controller
16
8
16
16
Data Latch
23
PCH
PCL
Program Counter
Loop
Stack
Control
Control
Logic
Logic
23
16
Data RAM
Address
Latch
23
16
RAGU
WAGU
Address Latch
Program Memory
Data EEPROM
EA MUX
Address Bus
Data Latch
ROM Latch
24
16
Instruction
Decode and
Control
Literal Data
16
Instruction Reg
Control Signals
to Various Blocks
Hardware
Multiplier
Divide
Support
16 x 16
W Register Array
16
16-Bit ALU
16
To Peripheral Modules
TABLE 3-1:
CPU CORE REGISTERS
Register(s) Name
W0 through W15
Description
Working Register Array
PC
23-Bit Program Counter
SR
ALU STATUS Register
SPLIM
Stack Pointer Limit Value Register
TBLPAG
Table Memory Page Address Register
PSVPAG
Program Space Visibility Page Address Register
RCOUNT
Repeat Loop Counter Register
CORCON
CPU Control Register
DS33030A-page 36
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 3-2:
PROGRAMMER’S MODEL
15
Divider Working Registers
0
W0 (WREG)
W1
W2
Multiplier Registers
W3
W4
W5
W6
W7
Working/Address
Registers
W8
W9
W10
W11
W12
W13
W14
Frame Pointer
W15
Stack Pointer
0
SPLIM
0
22
0
0
PC
7
0
TBLPAG
7
0
PSVPAG
15
0
RCOUNT
SRH
SRL
— — — — — — — DC
IPL
RA N OV Z C
2 1 0
15
15
Stack Pointer Limit
Value Register
Program Counter
Table Memory Page
Address Register
Program Space Visibility
Page Address Register
Repeat Loop Counter
Register
0
ALU STATUS Register (SR)
0
— — — — — — — — — — — — IPL3 PSV — —
CPU Control Register (CORCON)
Registers or bits are shadowed for PUSH.S and POP.S instructions.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 37
PIC24FV16KM204 FAMILY
3.2
CPU Control Registers
REGISTER 3-1:
SR: ALU STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0, HSC
—
—
—
—
—
—
—
DC
bit 15
bit 8
R/W-0, HSC(1)
R/W-0, HSC(1) R/W-0, HSC(1)
(2)
IPL1(2)
IPL2
IPL0(2)
R-0, HSC
R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0, HSC
RA
N
OV
Z
C
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-9
Unimplemented: Read as ‘0’
bit 8
DC: ALU Half Carry/Borrow bit
1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data)
of the result occurred
0 = No carry-out from the 4th or 8th low-order bit of the result has occurred
bit 7-5
IPL<2:0>: CPU Interrupt Priority Level Status bits(1,2)
111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled
110 = CPU Interrupt Priority Level is 6 (14)
101 = CPU Interrupt Priority Level is 5 (13)
100 = CPU Interrupt Priority Level is 4 (12)
011 = CPU Interrupt Priority Level is 3 (11)
010 = CPU Interrupt Priority Level is 2 (10)
001 = CPU Interrupt Priority Level is 1 (9)
000 = CPU Interrupt Priority Level is 0 (8)
bit 4
RA: REPEAT Loop Active bit
1 = REPEAT loop in progress
0 = REPEAT loop not in progress
bit 3
N: ALU Negative bit
1 = Result was negative
0 = Result was non-negative (zero or positive)
bit 2
OV: ALU Overflow bit
1 = Overflow occurred for signed (2’s complement) arithmetic in this arithmetic operation
0 = No overflow has occurred
bit 1
Z: ALU Zero bit
1 = An operation, which effects the Z bit, has set it at some time in the past
0 = The most recent operation, which effects the Z bit, has cleared it (i.e., a non-zero result)
bit 0
C: ALU Carry/Borrow bit
1 = A carry-out from the Most Significant bit (MSb) of the result occurred
0 = No carry-out from the Most Significant bit (MSb) of the result occurred
Note 1:
2:
The IPLx Status bits are read-only when NSTDIS (INTCON1<15>) = 1.
The IPL<2:0> Status bits are concatenated with the IPL3 bit (CORCON<3>) to form the CPU Interrupt
Priority Level (IPL). The value in parentheses indicates the IPL when IPL3 = 1.
DS33030A-page 38
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 3-2:
CORCON: CPU CONTROL REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R/C-0, HSC
R/W-0
U-0
U-0
—
—
—
—
IPL3(1)
PSV
—
—
bit 7
bit 0
Legend:
C = Clearable bit
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3
IPL3: CPU Interrupt Priority Level Status bit(1)
1 = CPU Interrupt Priority Level is greater than 7
0 = CPU Interrupt Priority Level is 7 or less
bit 2
PSV: Program Space Visibility in Data Space Enable bit
1 = Program space is visible in data space
0 = Program space is not visible in data space
bit 1-0
Unimplemented: Read as ‘0’
Note 1:
3.3
x = Bit is unknown
User interrupts are disabled when IPL3 = 1.
Arithmetic Logic Unit (ALU)
The PIC24F ALU is 16 bits wide and is capable of
addition, subtraction, bit shifts and logic operations.
Unless otherwise mentioned, arithmetic operations are
2’s complement in nature. Depending on the operation,
the ALU may affect the values of the Carry (C), Zero
(Z), Negative (N), Overflow (OV) and Digit Carry (DC)
Status bits in the SR register. The C and DC Status bits
operate as Borrow and Digit Borrow bits, respectively,
for subtraction operations.
The ALU can perform 8-bit or 16-bit operations,
depending on the mode of the instruction that is used.
Data for the ALU operation can come from the W
register array, or data memory, depending on the
addressing mode of the instruction. Likewise, output
data from the ALU can be written to the W register array
or a data memory location.
 2013 Microchip Technology Inc.
The PIC24F CPU incorporates hardware support for
both multiplication and division. This includes a
dedicated hardware multiplier and support hardware
division for 16-bit divisor.
3.3.1
MULTIPLIER
The ALU contains a high-speed, 17-bit x 17-bit
multiplier. It supports unsigned, signed or mixed sign
operation in several multiplication modes:
•
•
•
•
•
•
•
16-bit x 16-bit signed
16-bit x 16-bit unsigned
16-bit signed x 5-bit (literal) unsigned
16-bit unsigned x 16-bit unsigned
16-bit unsigned x 5-bit (literal) unsigned
16-bit unsigned x 16-bit signed
8-bit unsigned x 8-bit unsigned
Advance Information
DS33030A-page 39
PIC24FV16KM204 FAMILY
3.3.2
DIVIDER
3.3.3
The divide block supports 32-bit/16-bit and 16-bit/16-bit
signed and unsigned integer divide operations with the
following data sizes:
1.
2.
3.
4.
32-bit signed/16-bit signed divide
32-bit unsigned/16-bit unsigned divide
16-bit signed/16-bit signed divide
16-bit unsigned/16-bit unsigned divide
The quotient for all divide instructions ends up in W0
and the remainder in W1. Sixteen-bit signed and
unsigned DIV instructions can specify any W register
for both the 16-bit divisor (Wn), and any W register
(aligned) pair (W(m + 1):Wm) for the 32-bit dividend.
The divide algorithm takes one cycle per bit of divisor,
so both 32-bit/16-bit and 16-bit/16-bit instructions take
the same number of cycles to execute.
TABLE 3-2:
Instruction
MULTI-BIT SHIFT SUPPORT
The PIC24F ALU supports both single bit and
single-cycle, multi-bit arithmetic and logic shifts.
Multi-bit shifts are implemented using a shifter block,
capable of performing up to a 15-bit arithmetic right
shift, or up to a 15-bit left shift, in a single cycle. All
multi-bit shift instructions only support Register Direct
Addressing for both the operand source and result
destination.
A full summary of instructions that use the shift
operation is provided in Table 3-2.
INSTRUCTIONS THAT USE THE SINGLE AND MULTI-BIT SHIFT OPERATION
Description
ASR
Arithmetic shift right source register by one or more bits.
SL
Shift left source register by one or more bits.
LSR
Logical shift right source register by one or more bits.
DS33030A-page 40
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
4.0
MEMORY ORGANIZATION
As with Harvard architecture devices, the PIC24F
microcontrollers feature separate program and data
memory space and busing. This architecture also
allows the direct access of program memory from the
data space during code execution.
4.1
Program Address Space
The user access to the program memory space is
restricted to the lower half of the address range
(000000h to 7FFFFFh). The exception is the use of
TBLRD/TBLWT operations, which use TBLPAG<7> to
permit access to the Configuration bits and Device ID
sections of the configuration memory space.
Memory maps for the PIC24FV16KM204 family of
devices are displayed in Figure 4-1.
The program address memory space of the PIC24F
devices is 4M instructions. The space is addressable by
a 24-bit value derived from either the 23-bit Program
Counter (PC) during program execution, or from a table
operation or data space remapping, as described in
Section 4.3 “Interfacing Program and Data Memory
Spaces”.
PROGRAM SPACE MEMORY MAP FOR PIC24FV16KM204 FAMILY DEVICES
PIC24F08KM
PIC24F16KM
GOTO Instruction
Reset Address
Interrupt Vector Table
Reserved
Alternate Vector Table
GOTO Instruction
Reset Address
Interrupt Vector Table
Reserved
Alternate Vector Table
000000h
000002h
000004h
0000FEh
000100h
000104h
0001FEh
000200h
Flash
Program Memory
(2816 instructions)
User Memory Space
FIGURE 4-1:
User Flash
Program Memory
(5632 instructions)
Unimplemented
Read ‘0’
0015FEh
002BFEh
Unimplemented
Read ‘0’
Configuration Memory Space
7FFE00h
Note:
Data EEPROM
Data EEPROM
Reserved
Reserved
Device Config Registers
Device Config Registers
Reserved
Reserved
DEVID (2)
DEVID (2)
7FFFFFh
800000h
F7FFFEh
F80000h
F80010h
F80012h
FEFFFEh
FF0000h
FFFFFFh
Memory areas are not displayed to scale.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 41
PIC24FV16KM204 FAMILY
4.1.1
PROGRAM MEMORY
ORGANIZATION
4.1.3
In the PIC24FV16KM204 family, the data EEPROM is
mapped to the top of the user program memory space,
starting at address, 7FFE00, and expanding up to
address, 7FFFFF.
The program memory space is organized in
word-addressable blocks. Although it is treated as
24 bits wide, it is more appropriate to think of each
address of the program memory as a lower and upper
word, with the upper byte of the upper word being
unimplemented. The lower word always has an even
address, while the upper word has an odd address
(Figure 4-2).
The data EEPROM is organized as 16-bit wide memory
and 256 words deep. This memory is accessed using
Table Read and Write operations similar to the user
code memory.
4.1.4
Program memory addresses are always word-aligned
on the lower word, and addresses are incremented or
decremented by two during code execution. This
arrangement also provides compatibility with data
memory space addressing and makes it possible to
access data in the program memory space.
4.1.2
DEVICE CONFIGURATION WORDS
Table 4-1 provides the addresses of the device Configuration Words for the PIC24FV16KM204 family. Their
location in the memory map is displayed in Figure 4-1.
Refer to Section 26.1 “Configuration Bits” for more
information on device Configuration Words.
HARD MEMORY VECTORS
TABLE 4-1:
All PIC24F devices reserve the addresses between
00000h and 000200h for hard coded program
execution vectors. A hardware Reset vector is provided
to redirect code execution from the default value of the
PC on device Reset to the actual start of code. A GOTO
instruction is programmed by the user at 000000h with
the actual address for the start of code at 000002h.
DEVICE CONFIGURATION
WORDS FOR PIC24FV16KM204
FAMILY DEVICES
Configuration Word
PIC24F devices also have two Interrupt Vector
Tables, located from 000004h to 0000FFh, and
000104h to 0001FFh. These vector tables allow each
of the many device interrupt sources to be handled
by separate ISRs. Section 8.1 “Interrupt Vector
(IVT) Table” discusses the Interrupt Vector Tables in
more detail.
FIGURE 4-2:
DATA EEPROM
Configuration Word
Addresses
FBS
F80000
FGS
F80004
FOSCSEL
F80006
FOSC
F80008
FWDT
F8000A
FPOR
F8000C
FICD
F8000E
PROGRAM MEMORY ORGANIZATION
msw
Address
23
000001h
000003h
000005h
000007h
16
8
PC Address
(lsw Address)
0
000000h
000002h
000004h
000006h
00000000
00000000
00000000
00000000
Program Memory
‘Phantom’ Byte
(read as ‘0’)
DS33030A-page 42
least significant word
most significant word
Instruction Width
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
4.2
Data Address Space
4.2.1
The PIC24F core has a separate, 16-bit-wide data
memory space, addressable as a single linear range.
The data space is accessed using two Address
Generation Units (AGUs), one each for read and write
operations. The data space memory map is displayed
in Figure 4-3.
All Effective Addresses (EAs) in the data memory space
are 16 bits wide and point to bytes within the data space.
This gives a data space address range of 64 Kbytes or
32K words. The lower half of the data memory space
(that is, when EA<15> = 0) is used for implemented
memory addresses, while the upper half (EA<15> = 1) is
reserved for the Program Space Visibility (PSV) area
(see Section 4.3.3 “Reading Data From Program
Memory Using Program Space Visibility”).
DATA SPACE WIDTH
The data memory space is organized in
byte-addressable, 16-bit wide blocks. Data is aligned in
data memory and registers as 16-bit words, but all the
data space EAs resolve to bytes. The Least Significant
Bytes (LSBs) of each word have even addresses, while
the Most Significant Bytes (MSBs) have odd
addresses.
Depending on the particular device, PIC24FV16KM
family devices implement either 512 or 1024 words of
data memory. Should an EA point to a location outside
of this area, an all zero word or byte will be returned.
FIGURE 4-3:
DATA SPACE MEMORY MAP FOR PIC24FV16KM204 FAMILY DEVICES(3)
MSB
Address
0001h
07FFh
0801h
Implemented
Data RAM
09FFh(1)
MSB
LSB
LSB
Address
SFR Space
Data RAM
0BFFh(2)
0000h
07FEh
0800h
09FEh(1)
SFR
Space
Near
Data Space
0BFEh(2)
1FFFh
1FFEh
Unimplemented
Read as ‘0’
7FFFh
8001h
7FFFh
8000h
Program Space
Visibility Area
FFFFh
FFFEh
Note 1:
Upper data memory boundary for PIC24FXXKM10X devices.
2:
Upper data memory boundary for PIC24FXXKM20X devices.
3:
Data memory areas are not shown to scale.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 43
PIC24FV16KM204 FAMILY
4.2.2
DATA MEMORY ORGANIZATION
AND ALIGNMENT
To maintain backward compatibility with PIC® devices
and improve data space memory usage efficiency, the
PIC24F instruction set supports both word and byte
operations. As a consequence of byte accessibility, all
EA calculations are internally scaled to step through
word-aligned memory. For example, the core recognizes that Post-Modified Register Indirect Addressing
mode [Ws++] will result in a value of Ws + 1 for byte
operations and Ws + 2 for word operations.
Data byte reads will read the complete word, which
contains the byte, using the LSB of any EA to
determine which byte to select. The selected byte is
placed onto the LSB of the data path. That is, the data
memory and the registers are organized as two
parallel, byte-wide entities with shared (word) address
decode, but separate write lines. Data byte writes only
write to the corresponding side of the array or register,
which matches the byte address.
All word accesses must be aligned to an even address.
Misaligned word data fetches are not supported, so
care must be taken when mixing byte and word
operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error
trap will be generated. If the error occurred on a read,
the instruction underway is completed; if it occurred on
a write, the instruction will be executed, but the write
will not occur. In either case, a trap is then executed,
allowing the system and/or user to examine the
machine state prior to execution of the address Fault.
All byte loads into any W register are loaded into the
LSB; the MSB is not modified.
Although most instructions are capable of operating on
word or byte data sizes, it should be noted that some
instructions operate only on words.
4.2.3
NEAR DATA SPACE
The 8-Kbyte area between 0000h and 1FFFh is referred
to as the Near Data Space. Locations in this space are
directly addressable via a 13-bit absolute address field
within all memory direct instructions. The remainder of
the data space is addressable indirectly. Additionally, the
whole data space is addressable using MOV instructions,
which support Memory Direct Addressing (MDA) with a
16-bit address field. For PIC24F16KA102 family
devices, the entire implemented data memory lies in
Near Data Space (NDS).
4.2.4
SFR SPACE
The first 2 Kbytes of the Near Data Space, from 0000h
to 07FFh, are primarily occupied with Special Function
Registers (SFRs). These are used by the PIC24F core
and peripheral modules for controlling the operation of
the device.
SFRs are distributed among the modules that they
control and are generally grouped together by that
module. Much of the SFR space contains unused
addresses; these are read as ‘0’. The SFR space,
where the SFRs are actually implemented, is provided
in Table 4-2. Each implemented area indicates a
32-byte region where at least one address is
implemented as an SFR. A complete listing of
implemented SFRs, including their addresses, is
provided in Table 4-3 through Table 4-26.
A Sign-Extend (SE) instruction is provided to allow the
users to translate 8-bit signed data to 16-bit signed
values. Alternatively, for 16-bit unsigned data, users
can clear the MSB of any W register by executing a
Zero-Extend (ZE) instruction on the appropriate
address.
TABLE 4-2:
IMPLEMENTED REGIONS OF SFR DATA SPACE
SFR Space Address
xx00
000h
xx20
xx40
xx60
Core
ICN
100h
Timers
CLC
200h
MSSP
UART
400h
—
—
—
—
500h
—
—
—
—
600h
—
RTCC/Comp
—
Band Gap
700h
—
—
System/
HLVD
NVM/PMD
300h
Legend:
xx80
xxA0
xxC0
xxE0
Interrupts
—
MCCP/SCCP
Op Amp
DAC
A/D/CMTU
—
—
I/O
—
—
—
—
—
—
—
ANSEL
—
—
—
—
—
—
—
—
—
— = No implemented SFRs in this block.
DS33030A-page 44
Advance Information
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-3:
File
Name
Addr.
CPU CORE REGISTERS MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
0h
WREG0
0000
WREG1
2h
WREG1
0000
WREG2
4h
WREG2
0000
WREG3
6h
WREG3
0000
WREG4
8h
WREG4
0000
WREG5
Ah
WREG5
0000
WREG6
Ch
WREG6
0000
WREG7
Eh
WREG7
0000
WREG8
10h
WREG8
0000
WREG9
12h
WREG9
0000
WREG10
14h
WREG10
0000
WREG11
16h
WREG11
0000
WREG12
18h
WREG12
0000
WREG13
1Ah
WREG13
0000
WREG14
1Ch
WREG14
0000
WREG15
1Eh
WREG15
0800
SPLIM
20h
SPLIM
xxxx
PCL
2Eh
PCL
PCH
30h
—
—
—
—
—
—
—
—
PCH7
TBLPAG
32h
—
—
—
—
—
—
—
—
TBLPAG7
TBLPAG6 TBLPAG5 TBLPAG4 TBLPAG3 TBLPAG2 TBLPAG1 TBLPAG0
0000
PSVPAG
34h
—
—
—
—
—
—
—
—
PSVPAG7 PSVPAG6 PSVPAG5 PSVPAG4 PSVPAG3 PSVPAG2 PSVPAG1 PSVPAG0
0000
RCOUNT
36h
SR
42h
—
—
—
—
—
—
—
DC
IPL2
IPL1
IPL0
RA
N
OV
Z
C
0000
CORCON
44h
—
—
—
—
—
—
—
—
—
—
—
—
IPL3
PSV
—
—
0000
DISICNT
52h
—
—
Legend:
0000
PCH6
PCH5
PCH4
PCH3
PCH2
PCH1
PCH0
RCOUNT
0000
xxxx
DISICNT13 DISICNT12 DISICNT11 DISICNT10 DISICNT9 DISICNT8 DISICNT7 DISICNT6 DISICNT5 DISICNT4 DISICNT3 DISICNT2 DISICNT1 DISICNT0
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
xxxx
DS33030A-page 45
PIC24FV16KM204 FAMILY
Advance Information
WREG0
File
Name
Addr.
ICN REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
CN12PDE
CN11PDE
Bit 10
Bit 9
Bit 7
Bit 6
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
CN5PDE
CN4PDE
CN3PDE
CN2PDE
CN1PDE
CN0PDE
0000
56h
CN15PDE(1,2) CN14PDE CN13PDE
CNPD2
58h
CN31PDE(2) CN30PDE CN29PDE CN28PDE(2) CN27PDE(1,2) CN26PDE(2) CN25PDE(2) CN24PDE(1,2)
CNPD3
5Ah
—
—
—
—
—
—
—
—
—
—
—
CNEN1
62h
CN15IE(1,2)
CN14IE
CN13IE
CN12IE
CN11IE
CN10IE(2)
CN9IE(1,2)
—
CN7IE(1,2)
CN6IE
CN5IE
CN4IE
CN3IE
CN2IE
CNEN2
64h
CN31IE(2)
CN30IE
CN29IE
CN28IE(2)
CN27IE(1,2)
CN26IE(2)
CN25IE(2)
CN24IE(1,2)
CN23IE
CN22IE
CN21IE
CN20IE(2)
CN19IE(2)
CNEN3
66h
—
—
—
—
—
—
—
—
—
—
—
CN36IE(2)
CNPU1
6Eh
CN15PUE(1,2) CN14PUE CN13PUE
CN12PUE
CN11PUE
CN5PUE
CN4PUE
CNPU2
70h
CN31PUE(2) CN30PUE CN29PUE CN28PUE(2) CN27PUE(1,2) CN26PUE(2) CN25PUE(2) CN24PUE(1,2)
CNPU3
72h
Legend:
Note 1:
2:
—
—
—
—
CN10PUE(2) CN9PUE(1,2)
—
—
—
—
—
CN7PDE(1,2) CN6PDE
Bit 5
CNPD1
—
CN10PDE(2) CN9PDE(1,2)
Bit 8
CN23PDE
CN22PDE CN21PDE CN20PDE(2) CN19PDE(2) CN18PDE(2) CN17PDE(2) CN16PDE(1,2)
CN7PUE(1,2) CN6PUE
CN23PUE
—
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These bits are available only on 28-pin devices
These bits are available only on 44-pin devices
CN36PDE(2) CN35PDE(2) CN34PDE(2) CN33PDE(2)
0000
CN1IE
CN0IE
0000
CN18IE(2)
CN17IE(2)
CN16IE(1,2)
0000
CN35IE(2)
CN34IE(2)
CN33IE(2)
CN32IE(2)
0000
CN3PUE
CN2PUE
CN1PUE
CN0PUE
0000
CN22PUE CN21PUE CN20PUE(2) CN19PUE(2) CN18PUE(2) CN17PUE(2) CN16PUE(1,2)
—
—
0000
CN32PDE(2)
CN36PUE(2) CN35PUE(2) CN34PUE(2) CN33PUE(2)
CN32PUE(2)
0000
0000
Advance Information
PIC24FV16KM204 FAMILY
DS33030A-page 46
TABLE 4-4:
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-5:
File Name Addr.
INTERRUPT CONTROLLER REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
INTCON1
80h
NSTDIS
—
—
—
—
—
—
—
—
—
—
INTCON2
82h
ALTIVT
DISI
—
—
—
—
—
—
—
—
—
Bit 4
Bit 3
MATHERR ADDRERR
—
Bit 2
Bit 1
Bit 0
All
Resets
STKERR
OSCFAIL
—
0000
—
INT2EP
INT1EP
INT0EP
0000
IFS0
84h
NVMIF
—
AD1IF
U1TXIF
U1RXIF
—
—
CCP4IF
CCP3IF
—
T1IF
CCP2IF
CCP1IF
INT0IF
0000
IFS1
86h
U2TXIF
U2RXIF
INT2IF
CCT4IF
CCT3IF
—
—
—
—
CCP5IF
—
INT1IF
CNIF
CMIF
BCL1IF
SSP1IF
0000
IFS2
88h
—
—
—
—
—
—
CCT5IF
—
—
—
—
—
—
—
—
—
0000
IFS3
8Ah
—
RTCIF
—
—
—
—
—
—
—
—
—
—
—
BCL2IF
SSP2IF
—
0000
IFS4
8Ch
DAC2IF
DAC1IF
CTMUIF
—
—
—
—
HLVDIF
—
—
—
—
—
U2ERIF
U1ERIF
—
0000
IFS5
8Eh
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ULPWUIF
0000
—
—
0000
CCT2IF CCT1IF
90h
—
—
—
—
—
—
—
94h
NVMIE
—
AD1IE
U1TXIE
U1RXIE
—
—
IEC1
96h
U2TXIE
U2RXIE
INT2IE
CCT4IE
CCT3IE
—
—
—
IEC2
98h
—
—
—
—
—
—
CCT5IE
IEC3
9Ah
—
RTCIE
—
—
—
—
—
IEC4
9Ch
DAC2IE
DAC1IE
CTMUIE
—
—
—
IEC5
9Eh
—
—
—
—
—
—
—
—
—
—
CLC2IF
CLC1IF
CCP4IE
CCP3IE
—
T1IE
CCP2IE
CCP1IE
INT0IE
0000
—
CCP5IE
—
INT1IE
CNIE
CMIE
BCL1IE
SSP1IE
0000
—
—
—
—
—
—
—
—
—
0000
—
—
—
—
—
—
BCL2IE
SSP2IE
—
0000
—
HLVDIE
—
—
—
—
—
U2ERIE
U1ERIE
—
0000
—
—
—
—
—
—
—
—
—
—
ULPWUIE
0000
—
—
—
CCT2IE CCT1IE
DS33030A-page 47
IEC6
A0h
—
—
—
—
—
—
—
—
—
—
—
CLC2IE
CLC1IE
0000
IPC0
A4h
—
T1IP2
T1IP1
T1IP0
—
CCP2IP2 CCP2IP1 CCP2IP0
—
CCP1IP2
CCP1IP1
CCP1IP0
—
INT0IP2
INT0IP1
INT0IP0
4444
IPC1
A6h
—
CCT1IP2 CCT1IP1 CCT1IP0
—
CCP4IP2 CCP4IP1 CCP4IP0
—
CCP3IP2
CCP3IP1
CCP3IP0
—
—
—
—
4440
IPC2
A8h
—
U1RXIP2 U1RXIP1 U1RXIP0
—
—
—
—
—
—
—
CCT2IP2
CCT2IP1
CCT2IP0
4004
IPC3
AAh
—
NVMIP2
NVMIP1
NVMIP0
—
—
—
—
—
AD1IP2
AD1IP1
AD1IP0
—
U1TXIP2
U1TXIP1
U1TXIP0
4044
IPC4
ACh
—
CNIP2
CNIP1
CNIP0
—
CMIP2
CMIP1
CMIP0
—
BCL1IP2
BCL1IP1
BCL1IP0
—
SSP1IP2
SSP1IP1
SSP1IP0
4444
IPC5
AEh
—
—
—
—
—
—
—
—
—
—
INT1IP2
INT1IP1
INT1IP0
0404
IPC6
B0h
—
CCT3IP2 CCT3IP1 CCT3IP0
—
—
—
—
—
—
—
—
—
4000
IPC7
B2h
—
U2TXIP2 U2TXIP1 U2TXIP0
—
—
INT2IP2
INT2IP1
INT2IP0
—
CCT4IP2
CCT4IP1
CCT4IP0
4444
IPC10
B8h
—
—
—
—
—
—
CCT5IP2
CCT5IP1
CCT5IP0
—
—
—
—
0040
IPC12
BCh
—
—
—
—
—
BCL2IP2 BCL2IP1 BCL2IP0
—
SSP2IP2
SSP2IP1
SSP2IP0
—
—
—
—
0440
IPC15
C2h
—
—
—
—
—
RTCIP2
—
—
—
—
—
—
—
—
0400
IPC16
C4h
—
—
—
—
—
—
U1ERIP2
U1ERIP1
U1ERIP0
—
—
—
—
0440
IPC18
C8h
—
—
—
—
—
—
—
—
—
—
HLVDIP2
HLVDIP1
HLVDIP0
0004
IPC19
CAh
—
—
—
—
IPC20
CCh
—
—
IPC24
D4h
—
INTTREG
E0h
CPUIRQ
Legend:
DAC2IP2 DAC2IP1 DAC2IP0
—
—
—
—
CCP5IP2 CCP5IP1 CCP5IP0
—
—
—
U2RXIP2 U2RXIP1 U2RXIP0
—
—
RTCIP1
—
RTCIP0
U2ERIP2 U2ERIP1 U2ERIP0
—
—
—
DAC1IP2 DAC1IP1 DAC1IP0
—
—
—
—
—
—
—
—
—
VHOLD
—
ILR3
ILR2
—
CTMUIP2
CTMUIP1
CTMUIP0
—
—
—
—
—
—
—
—
—
—
CLC2IP2
CLC2IP1
CLC2IP0
—
ILR1
ILR0
—
—
ULPWUIP2 ULPWUIP1 ULPWUIP0
CLC1IP2
CLC1IP1
CLC1IP0
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
4440
0004
0044
0000
PIC24FV16KM204 FAMILY
Advance Information
IFS6
IEC0
File Name
TIMER1 REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TMR1
100h
Timer1 Register
xxxx
PR1
102h
Timer1 Period Register 1
FFFF
T1CON
Legend:
104h
TON
—
TSIDL
—
—
—
TECS1
TECS0
—
TGATE
TCKPS1
TCKPS0
—
TSYNC
TCS
—
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
TABLE 4-7:
File Name
CLC1-2 REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
CLC1CONL
122h
LCEN
—
—
—
INTP
INTN
—
—
LCOE
LCOUT
LCPOL
CLC1CONH
124h
—
—
—
—
—
—
—
—
—
—
—
All
Resets
Bit 3
Bit 2
Bit 1
Bit 0
—
—
MODE2
MODE1
MODE0
0000
—
G4POL
G3POL
G2POL
G1POL
0000
Advance Information
CLC1SEL
126h
—
DS42
DS41
DS40
—
DS32
DS31
DS30
—
DS22
DS21
DS20
—
DS12
DS11
DS10
0000
CLC1GLSL
12Ah
G2D4T
G2D4N
G2D3T
G2D3N
G2D2T
G2D2N
G2D1T
G2D1N
G1D4T
G1D4N
G1D3T
G1D3N
G1D2T
G1D2N
G1D1T
G1D1N
0000
CLC1GLSH
12Ch
G4D4T
G4D4N
G4D3T
G4D3N
G4D2T
G4D2N
G4D1T
G4D1N
G3D4T
G3D4N
G3D3T
G3D3N
G3D2T
G3D2N
G3D1T
G3D1N
0000
CLC2CONL(1)
12Eh
LCEN
—
—
—
INTP
INTN
—
—
LCOE
LCOUT
LCPOL
—
—
MODE2
MODE1
MODE0
0000
CLC2CONH(1)
130h
—
—
—
—
—
—
—
—
—
—
—
—
G4POL
G3POL
G2POL
G1POL
0000
CLC2SEL(1)
132h
—
DS42
DS41
DS40
—
DS32
DS31
DS30
—
DS22
DS21
DS20
—
DS12
DS11
DS10
0000
CLC2GLSL(1)
136h
G2D4T
G2D4N
G2D3T
G2D3N
G2D2T
G2D2N
G2D1T
G2D1N
G1D4T
G1D4N
G1D3T
G1D3N
G1D2T
G1D2N
G1D1T
G1D1N
0000
CLC2GLSH(1)
138h
G4D4T
G4D4N
G4D3T
G4D3N
G4D2T
G4D2N
G4D1T
G4D1N
G3D4T
G3D4N
G3D3T
G3D3N
G3D2T
G3D2N
G3D1T
G3D1N
0000
Legend:
Note 1:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
PIC24FV16KM204 FAMILY
DS33030A-page 48
TABLE 4-6:
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-8:
MCCP1 REGISTER MAP
File Name
Addr.
CCP1CON1L
140h
CCPON
—
CCP1CON1H
142h
OPSSRC
RTRGEN
—
—
OPS3
OPS2
OPS1
OPS0
TRIGEN
CCP1CON2L
144h
PWMRSEN
ASDGM
—
SSDG
—
—
—
—
ASDG7
ASDG6
CCP1CON2H
146h
OENSYNC
—
OCFEN
OCEEN
OCDEN
OCCEN
OCBEN
OCAEN
ICGSM1
ICGSM0
CCP1CON3L
148h
—
—
—
—
—
—
—
—
—
OETRIG
OSCNT2
—
OUTM2
OUTM1
OUTM0
—
—
—
—
—
—
—
CCPTRIG
CCP1CON3H 14Ah
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
CCPSIDL CCPSLP TMRSYNC CLKSEL2 CLKSEL1 CLKSEL0 TMRPS1
OSCNT1 OSCNT0
—
MOD1
MOD0
0000
SYNC1
SYNC0
0000
ASDG1
ASDG0
0000
ICS2
ICS1
ICS0
0100
DT2
DT1
DT0
0000
PSSBDF0
0000
ICBNE
0000
Bit 4
Bit 2
TMRPS0
T32
CCSEL
MOD3
MOD2
SYNC4
SYNC3
SYNC2
ASDG5
ASDG4
ASDG3
ASDG2
—
AUXOUT1
AUXOUT0
DT5
DT4
DT3
—
POLACE
POLBDF
PSSACE1
TRSET
TRCLR
ASEVT
SCEVT
Bit 1
PSSACE0 PSSBDF1
14Ch
CCP1TMRL
150h
Time Base Register Low Word
0000
CCP1TMRH
152h
Time Base Register High Word
0000
CCP1PRL
154h
Time Base Period Register Low Word
FFFF
CCP1PRH
156h
Time Base Period Register High Word
FFFF
CCP1RAL
158h
Output Compare Data Word A
0000
CCP1RBL
15Ch
Output Compare Data Word B
0000
CCP1BUFL
160h
Input Capture Data Buffer Low Word
0000
CCP1BUFH
162h
Input Capture Data Buffer High Word
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
ICDIS
ICOV
DS33030A-page 49
PIC24FV16KM204 FAMILY
Advance Information
CCP1STATL
Legend:
—
All
Resets
Bit 5
ONESHOT ALTSYNC
Bit 3
Bit 0
Bit 6
MCCP2 REGISTER MAP
File Name
Addr.
Bit 15
CCP2CON1L
164h
CCP2CON1H 166h
CCP2CON2L
Bit 14
Bit 13
Bit 12
Bit 11
CCPON
—
CCPSIDL
CCPSLP
OPSRC
RTRGEN
—
—
IOPS3
IOPS2
IOPS1
IOPS0
TRIGEN
168h PWMRSEN ASDGM
—
SSDG
—
—
—
—
ASDG7
ASDG6
ASDG5
Bit 8
OCAEN
ICGSM1
ICGSM0
—
—
—
OCFEN(1) OCEEN(1) OCDEN(1) OCCEN(1) OCBEN(1)
—
CCP2CON3L
—
—
—
—
—
OETRIG
OSCNT2
OSCNT1
OSCNT0
—
—
—
—
—
—
CCP2CON3H 16Eh
Bit 9
Bit 7
TMRSYNC CLKSEL2 CLKSEL1 CLKSEL0 TMRPS1
CCP2CON2H 16Ah OENSYNC
16Ch
Bit 10
—
—
OUTM2(1) OUTM1(1) OUTM0(1)
—
—
MOD1
MOD0
0000
SYNC1
SYNC0
0000
ASDG1
ASDG0
0000
ICSEL2
ICSEL1
ICSEL0
0100
DT2
DT1
DT0
0000
Bit 4
TMRPS0
T32
CCSEL
MOD3
MOD2
SYNC4
SYNC3
SYNC2
ASDG4
ASDG3
ASDG2
DT5
—
—
CCPTRIG
TRSET
AUXOUT1 AUXOUT0
DT4
DT3
Bit 2
Bit 1
POLACE POLBDF(1) PSSACE1 PSSACE0 PSSBDF1(1) PSSBDF0(1)
Advance Information
170h
CCP2TMRL
174h
Time Base Register Low Word
0000
CCP2TMRH
176h
Time Base Register High Word
0000
CCP2PRL
178h
Time Base Period Register Low Word
FFFF
CCP2PRH
17Ah
Time Base Period Register High Word
FFFF
CCP2RAL
17Ch
Output Compare Data Word A
0000
CCP2RBL
180h
Output Compare Data Word B
0000
CCP2BUFL
184h
Input Capture Data Buffer Low Word
0000
CCP2BUFH
186h
Input Capture Data Buffer High Word
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These bits are available only on PIC24F(V)16KM2XX devices.
TRCLR
ASEVT
SCEVT
ICDIS
ICOV
ICBNE
0000
CCP2STATL
Legend:
Note 1:
—
All
Resets
Bit 5
ONESHOT ALTSYNC
Bit 3
Bit 0
Bit 6
0000
PIC24FV16KM204 FAMILY
DS33030A-page 50
TABLE 4-9:
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-10:
MCCP3 REGISTER MAP
File Name
Addr.
Bit 15
CCP3CON1L(1)
188h
CCPON
—
CCP3CON1H(1) 18Ah
OPSRC
RTRGEN
—
—
IOPS3
IOPS2
IOPS1
IOPS0
TRIGEN
18Ch PWMRSEN ASDGM
—
SSDG
—
—
—
—
ASDG7
ASDG6
CCP3CON2L(1)
CCP3CON2H(1) 18Eh
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
CCPSIDL CCPSLP TMRSYNC CLKSEL2 CLKSEL1 CLKSEL0 TMRPS1
Bit 6
Bit 5
Bit 4
TMRPS0
T32
CCSEL
MOD3
MOD2
SYNC4
SYNC3
SYNC2
ASDG5
ASDG4
ASDG3
ASDG2
ONESHOT ALTSYNC
Bit 3
Bit 2
Bit 0
All
Resets
MOD1
MOD0
0000
SYNC1
SYNC0
0000
ASDG1
ASDG0
0000
Bit 1
OENSYNC
—
OCFEN
OCEEN
OCDEN
OCCEN
OCBEN
OCAEN
ICGSM1
ICGSM0
—
AUXOUT1
AUXOUT0
ICS2
ICS1
ICS0
0100
—
—
—
—
—
—
—
—
—
DT5
DT4
DT3
DT2
DT1
DT0
0000
—
OUTM2
OUTM1
OUTM0
—
—
POLACE
POLBDF
—
—
—
—
CCPTRIG
TRSET
TRCLR
ASEVT
190h
—
CCP3CON3H(1)
192h
OETRIG
CCP3STAT(1)
194h
—
CCP3TMRL(1)
198h
Time Base Register Low Word
0000
CCP3TMRH(1)
19Ah
Time Base Register High Word
0000
CCP3PRL(1)
19Ch
Time Base Period Register Low Word
FFFF
CCP3PRH(1)
19Eh
Time Base Period Register High Word
FFFF
CCP3RAL(1)
1A0h
Output Compare Data Word A
0000
CCP3RBL(1)
1A4h
Output Compare Data Word B
0000
CCP3BUFL(1)
1A8h
Input Capture Data Buffer Low Word
0000
CCP3BUFH(1)
1AAh
Input Capture Data Buffer High Word
0000
Legend:
Note 1:
OSCNT2 OSCNT1 OSCNT0
—
—
—
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
PSSACE1 PSSACE0 PSSBDF1 PSSBDF0
SCEVT
ICDIS
ICOV
ICBNE
0000
0000
DS33030A-page 51
PIC24FV16KM204 FAMILY
Advance Information
CCP3CON3L(1)
SCCP4 REGISTER MAP
Bit 12
Bit 10
Bit 9
Bit 8
Bit 7
T32
CCSEL
MOD3
MOD2
SYNC4
SYNC3
SYNC2
ASDG4
ASDG3
ASDG2
ICSEL2
0000
0000
ICSEL1
ICSEL0
0100
—
—
0000
ICOV
ICBNE
0000
Advance Information
—
IOPS3
IOPS2
IOPS1
IOPS0
TRIGEN
CCP4CON2L(1)
1B0h PWMRSEN ASDGM
—
SSDG
—
—
—
—
ASDG7
ASDG6
ASDG5
CCP4CON2H(1)
1B2h
OENSYNC
—
—
—
—
—
OCAEN
ICGSM1
ICGSM0
—
CCP4CON3H(1)
1B6h
OETRIG
—
—
—
—
—
—
POLACE
—
CCP4STATL(1)
1B8h
—
—
—
—
—
CCPTRIG
TRSET
TRCLR
ASEVT
CCP4TMRL(1)
1BCh
Time Base Register Low Word
0000
CCP4TMRH(1)
1BEh
Time Base Register High Word
0000
CCP4PRL(1)
1C0h
Time Base Period Register Low Word
FFFF
CCP4PRH(1)
1C2h
Time Base Period Register High Word
FFFF
CCP4RAL(1)
1C4h
Output Compare Data Word A
0000
CCP4RBL(1)
1C8h
Output Compare Data Word B
0000
CCP4BUFL(1)
1CCh
Input Capture Data Buffer Low Word
0000
CCP4BUFH(1)
1CEh
Input Capture Data Buffer High Word
0000
—
TMRPS0
ASDG0
—
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
AUXOUT1 AUXOUT0
Bit 2
ASDG1
RTRGEN
ONESHOT ALTSYNC
Bit 3
0000
—
OPSRC
—
Bit 4
MOD0
CCPON
OSCNT2 OSCNT1 OSCNT0
Bit 5
SYNC0
1ACh
CCP4CON1H(1) 1AEh
CCPSIDL CCPSLP TMRSYNC CLKSEL2 CLKSEL1 CLKSEL0 TMRPS1
Bit 6
MOD1
CCP4CON1L(1)
—
Bit 11
SYNC1
Bit 15
—
Bit 13
All
Resets
Addr.
Legend:
Note 1:
Bit 14
Bit 0
File Name
PSSACE1 PSSACE0
SCEVT
ICDIS
Bit 1
PIC24FV16KM204 FAMILY
DS33030A-page 52
TABLE 4-11:
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-12:
SCCP5 REGISTER MAP
Bit 12
Bit 10
Bit 9
Bit 8
Bit 7
MOD1
MOD0
0000
SYNC0
0000
ASDG1
ASDG0
0000
ICSEL2
ICSEL1
ICSEL0
0100
PSSACE1
PSSACE0
—
—
0000
SCEVT
ICDIS
ICOV
ICBNE
0000
1D0h
CCPON
—
CCP5CON1H(1)
1D2h
OPSRC
RTRGEN
—
—
IOPS3
IOPS2
IOPS1
IOPS0
TRIGEN
CCP5CON2L(1)
1D4h
PWMRSEN ASDGM
—
SSDG
—
—
—
—
ASDG7
ASDG6
ASDG5
CCP5CON2H(1)
1D6h
OENSYNC
—
—
—
—
—
OCAEN
ICGSM1
ICGSM0
—
CCP5CON3H(1)
1DAh
OETRIG
—
—
—
—
—
—
POLACE
—
CCP5STATL(1)
1DCh
—
—
—
—
—
CCPTRIG
TRSET
TRCLR
ASEVT
CCP5TMRL(1)
1E0h
Time Base Register Low Word
0000
CCP5TMRH(1)
1E2h
Time Base Register High Word
0000
CCP5PRL(1)
1E4h
Time Base Period Register Low Word
FFFF
CCP5PRH(1)
1E6h
Time Base Period Register High Word
FFFF
CCP5RAL(1)
1E8h
Output Compare Data Word A
0000
CCP5RBL(1)
1ECh
Output Compare Data Word B
0000
CCP5BUFL(1)
1F0h
Input Capture Data Buffer Low Word
0000
CCP5BUFH(1)
1F2h
Input Capture Data Buffer High Word
0000
CCPSIDL CCPSLP TMRSYNC CLKSEL2 CLKSEL1 CLKSEL0 TMRPS1
OSCNT2 OSCNT1 OSCNT0
—
—
Bit 6
Bit 5
Bit 4
TMRPS0
T32
CCSEL
MOD3
MOD2
SYNC4
SYNC3
SYNC2
ASDG4
ASDG3
ASDG2
ONESHOT ALTSYNC
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
Bit 3
AUXOUT1 AUXOUT0
Bit 2
Bit 1
DS33030A-page 53
PIC24FV16KM204 FAMILY
Advance Information
CCP5CON1L(1)
—
Bit 11
SYNC1
Bit 15
—
Bit 13
All
Resets
Addr.
Legend:
Note 1:
Bit 14
Bit 0
File Name
File Name
MSSP1 (I2C™/SPI) REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SSP1BUF
200h
—
—
—
—
—
—
—
—
SSP1CON1
202h
—
—
—
—
—
—
—
—
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
0000
SSP1CON2
204h
—
—
—
—
—
—
—
—
GCEN
ACKSTAT
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
0000
SSP1CON3
206h
—
—
—
—
—
—
—
—
ACKTIM
PCIE
SCIE
BOEN
SDAHT
SBCDE
AHEN
DHEN
0000
SSP1STAT
208h
—
—
—
—
—
—
—
—
SMP
CKE
D/A
P
S
R/W
UA
BF
SSP1ADD
20Ah
—
—
—
—
—
—
—
—
20Ch
—
—
—
—
—
—
—
—
SSP1MSK
Legend:
MSSP Receive Buffer/Transmit Register
All
Resets
MSSP Address Register in I2C Slave Mode
MSSP Baud Rate Reload Register in I2C Master Mode
MSK7
MSK6
MSK5
0000
0000
Advance Information
MSK4
MSK3
MSK2
MSK1
MSK0
00FF
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
TABLE 4-14:
MSSP2 (I2C™/SPI) REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
SSP2BUF(1)
210h
—
—
—
—
—
—
—
—
SSP2CON1(1)
212h
—
—
—
—
—
—
—
SSP2CON2(1)
214h
—
—
—
—
—
—
SSP2CON3(1)
216h
—
—
—
—
—
SSP2STAT(1)
218h
—
—
—
—
SSP2ADD(1)
21Ah
—
—
—
SSP2MSK(1)
21Ch
—
—
—
Legend:
Note 1:
00xx
Bit 7
Bit 6
Bit 5
—
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
0000
—
—
GCEN
ACKSTAT
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
0000
—
—
—
ACKTIM
PCIE
SCIE
BOEN
SDAHT
SBCDE
AHEN
DHEN
0000
—
—
—
—
SMP
CKE
D/A
P
S
R/W
UA
BF
0000
—
—
—
—
—
—
—
—
—
—
MSSP Receive Buffer/Transmit Register
00xx
MSSP Address Register in I2C Slave Mode
MSSP Baud Rate Reload Register in I2C Master Mode
MSK7
MSK6
MSK5
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
MSK4
MSK3
MSK2
MSK1
0000
MSK0
00FF
PIC24FV16KM204 FAMILY
DS33030A-page 54
TABLE 4-13:
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-15:
UART1 REGISTER MAP
File Name
Addr.
U1MODE
220h
U1STA
222h
U1TXREG
224h
—
—
U1RXREG
226h
—
—
U1BRG
228h
Legend:
Bit 15
Bit 14
Bit 13
Bit 12
UARTEN
—
USIDL
IREN
RTSMD
—
UTXBRK
—
—
—
—
—
—
—
—
—
—
UTXISEL1 UTXINV UTXISEL0
Bit 11
Bit 10
Bit 9
Bit 8
—
UEN1
UEN0
UTXEN UTXBF
TRMT
Bit 7
Bit 6
WAKE
LPBACK
URXISEL1 URXISEL0
All
Resets
PDSEL0
STSEL
0000
OERR
URXDA
Bit 4
Bit 3
Bit 2
Bit 1
ABAUD
URXINV
BRGH
PDSEL1
ADDEN
RIDLE
PERR
FERR
UART1 Transmit Register
0110
xxxx
UART1 Receive Register
0000
Baud Rate Generator Prescaler
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
TABLE 4-16:
File Name
Addr.
UART2 REGISTER MAP
Bit 14
Bit 13
Bit 12
UARTEN
—
USIDL
IREN
Bit 11
Bit 10
Bit 9
Bit 8
RTSMD
—
UEN1
UEN0
UTXBRK UTXEN UTXBF
TRMT
Bit 7
Bit 6
WAKE
LPBACK
STSEL
0000
OERR
URXDA
0110
Bit 2
Bit 1
ABAUD
URXINV
BRGH
PDSEL1
ADDEN
RIDLE
PERR
FERR
232h
U2TXREG(1)
234h
—
—
—
—
—
—
—
UART2 Transmit Register
U2RXREG(1)
236h
—
—
—
—
—
—
—
UART2 Receive Register
U2BRG(1)
238h
URXISEL1 URXISEL0
PDSEL0
Bit 3
230h
—
All
Resets
Bit 4
U2MODE(1)
UTXISEL1 UTXINV UTXISEL0
Bit 0
Bit 5
Baud Rate Generator Prescaler
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
xxxx
0000
0000
DS33030A-page 55
PIC24FV16KM204 FAMILY
Advance Information
Bit 15
U2STA(1)
Legend:
Note 1:
Bit 0
Bit 5
OP AMP 1 REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
AMP1CON(1)
24Ah
AMPEN
—
Legend:
Note 1:
AMPSIDL AMPSLP
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
—
—
—
—
SPDSEL
—
NINSEL2
Bit 3
Bit 1
Bit 0
All
Resets
PINSEL1
PINSEL0
0000
Bit 1
Bit 0
All
Resets
PINSEL1
PINSEL0
0000
Bit 2
NINSEL1 NINSEL0 PINSEL2
OP AMP 2 REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
AMP2CON(1)
24Ch
AMPEN
—
Bit 13
Bit 12
AMPSIDL AMPSLP
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
—
—
—
—
SPDSEL
—
NINSEL2
Bit 3
Bit 2
NINSEL1 NINSEL0 PINSEL2
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
Advance Information
TABLE 4-19:
File Name
Bit 12
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
TABLE 4-18:
Legend:
Note 1:
Bit 13
Addr.
DAC1CON(1) 274h
DAC1 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
DACEN
—
DACSIDL
DACSLP
DACFM
—
SRDIS
DACTRIG
DACOE
Bit 6
Bit 5
Bit 4
Bit 3
DACTSEL4 DACTSEL3 DACTSEL2 DACTSEL1
Bit 2
Bit 1
Bit 0
All
Resets
DACTSEL0
DACREF1
DACREF0
0000
DAC1DAT(1)
276h DACDAT15(2) DACDAT14(2) DACDAT13(2) DACDAT12(2) DACDAT11(2) DACDAT10(2) DACDAT9(2) DACDAT8(2) DACDAT7(2) DACDAT6(2) DACDAT5(2) DACDAT4(2) DACDAT3(2) DACDAT2(2) DACDAT1(2) DACDAT0(2) 0000
Legend:
Note 1:
2:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM1XX devices.
The 8-bit result format depends on the value of the DACFM control bit.
TABLE 4-20:
File Name
Addr.
DAC2CON(1) 278h
DAC2 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
DACEN
—
DACSIDL
DACSLP
DACFM
—
SRDIS
DACTRIG
DACOE
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
DACTSEL4 DACTSEL3 DACTSEL2 DACTSEL1 DACTSEL0
Bit 1
Bit 0
All
Resets
DACREF1
DACREF0
0000
 2013 Microchip Technology Inc.
DAC2DAT(1)
27Ah DACDAT15(2) DACDAT14(2) DACDAT13(2) DACDAT12(2) DACDAT11(2) DACDAT10(2) DACDAT9(2) DACDAT8(2) DACDAT7(2) DACDAT6(2) DACDAT5(2) DACDAT4(2) DACDAT3(2) DACDAT2(2) DACDAT1(2) DACDAT0(2) 0000
Legend:
Note 1:
2:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers are available only on PIC24F(V)16KM2XX devices.
The 8-bit result format depends on the value of the DACFM control bit.
PIC24FV16KM204 FAMILY
DS33030A-page 56
TABLE 4-17:
 2013 Microchip Technology Inc.
TABLE 4-21:
PORTA REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11(4,5)
Bit 10(4,5)
Bit 9(4,5)
Bit 8(4,5)
Bit 7(4)
Bit 6(3)
Bit 5(2)
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISA
2C0h
—
—
—
—
TRISA11
TRISA10
TRISA9
TRISA8
TRISA7
TRISA6
—
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
0FDF(1)
PORTA
2C2h
—
—
—
—
RA11
RA10
RA9
RA8
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
xxxx
LATA
2C4h
—
—
—
—
LATA11
LATA10
LATA9
LATA8
LATA7
LATA6
—
LATA4
LATA3
LATA2
LATA1
LATA0
xxxx
ODCA
2C6h
—
—
—
—
ODA11
ODA10
ODA9
ODA8
ODA7
ODA6
—
ODA4
ODA3
ODA2
ODA1
ODA0
0000
Legend:
Note 1:
2:
3:
4:
5:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
Reset value depends on the device type; the PIC24F16KM204 value is shown.
These bits are only available when MCLRE (FPOR<7>) = 0.
These bits are not implemented in FV devices.
These bits are not implemented in 20-pin devices.
These bits are not implemented in 28-pin devices.
TABLE 4-22:
Addr.
TRISB
2C8h
Bit 15
Bit 14
Bit 13
Bit 12
TRISB15 TRISB14 TRISB13 TRISB12
Bit 11(2)
Bit 10(2)
Bit 9
Bit 8
Bit 7
Bit 6(2)
Bit 5(2)
Bit 4
Bit 3(2)
Bit 2
Bit 1
Bit 0
All
Resets
TRISB11
TRISB10
TRISB9
TRISB8
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
FFFF(1)
PORTB
2CAh
RB15
RB14
RB13
RB12
RB11
RB10
RB9
RB8
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx
LATB
2CCh
LATB15
LATB14
LATB13
LATB12
LATB11
LATB10
LATB9
LATB8
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx
ODCB
2CEh
ODB15
ODB14
ODB13
ODB12
ODB11
ODB10
ODB9
ODB8
ODB7
ODB6
ODB5
ODB4
ODB3
ODB2
ODB1
ODB0
0000
Legend:
Note 1:
2:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
Reset value depends on the device type; the PIC24F16KM204 value is shown.
These bits are not implemented in 20-pin devices.
TABLE 4-23:
File
Name
PORTC REGISTER MAP
Bit 9(2,3) Bit 8(2,3)
Bit 7(2,3)
Bit 6(2,3)
Bit 5(2,3)
Bit 4(2,3)
Bit 3(2,3)
Bit 2(2,3)
Bit 1(2,3)
Bit 0(2,3)
All
Resets
—
TRISC9
TRISC8
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
03FF(1)
—
RC9
RC8
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx
—
—
LATC9
LATC8
LATC7
LATC6
LATC5
LATC4
LATC3
LATC2
LATC1
LATC0
xxxx
—
—
ODC9
ODC8
ODC7
ODC6
ODC5
ODC4
ODC3
ODC2
ODC1
ODC0
0000
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
TRISC
2D0h
—
—
—
—
—
PORTC
2D2h
—
—
—
—
—
LATTC
2D4h
—
—
—
—
ODCC
2D6h
—
—
—
—
DS33030A-page 57
Legend:
Note 1:
2:
3:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
Reset value depends on the device type; the PIC24F16KM204 value is shown.
These bits are not implemented in 20-pin devices.
These bits are not implemented in 28-pin devices.
PIC24FV16KM204 FAMILY
Advance Information
File Name
PORTB REGISTER MAP
PAD CONFIGURATION REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
PADCFG1
2FCh
—
—
—
—
SDO2DIS(1)
Legend:
Note 1:
Bit 10
Bit 9
SCK2DIS(1) SDO1DIS
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
SCK1DIS
—
—
—
—
—
—
—
—
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These bits are not available on the PIC24F(V)08KM101 device, read as ‘0’.
Advance Information
PIC24FV16KM204 FAMILY
DS33030A-page 58
TABLE 4-24:
 2013 Microchip Technology Inc.
 2013 Microchip Technology Inc.
TABLE 4-25:
A/D REGISTER MAP
DS33030A-page 59
ADC1BUF0
300h
A/D Data Buffer 0/Threshold for Channel 0/Threshold for Channel 0 & 12 in Window Compare
xxxx
ADC1BUF1
302h
A/D Data Buffer 1/Threshold for Channel 1/Threshold for Channel 1 & 13 in Window Compare
xxxx
ADC1BUF2
304h
A/D Data Buffer 2/Threshold for Channel 2/Threshold for Channel 2 & 14 in Window Compare
xxxx
ADC1BUF3
306h
A/D Data Buffer 3/Threshold for Channel 3/Threshold for Channel 3 & 15 in Window Compare
xxxx
ADC1BUF4
308h
A/D Data Buffer 4/Threshold for Channel 4/Threshold for Channel 4 & 16 in Window Compare
xxxx
ADC1BUF5
30Ah
A/D Data Buffer 5/Threshold for Channel 5/Threshold for Channel 5 & 17 in Window Compare
xxxx
ADC1BUF6
30Ch
A/D Data Buffer 6/Threshold for Channel 6/Threshold for Channel 6 & 18 in Window Compare
xxxx
ADC1BUF7
30Eh
A/D Data Buffer 7/Threshold for Channel 7/Threshold for Channel 7 & 19 in Window Compare
xxxx
ADC1BUF8
310h
A/D Data Buffer 8/Threshold for Channel 8/Threshold for Channel 8 & 20 in Window Compare
xxxx
ADC1BUF9
312h
A/D Data Buffer 9/Threshold for Channel 9/Threshold for Channel 9 & 21 in Window Compare
xxxx
ADC1BUF10
314h
A/D Data Buffer 10/Threshold for Channel 10/Threshold for Channel 10 & 22 in Window Compare
xxxx
ADC1BUF11
316h
A/D Data Buffer 11/Threshold for Channel 11/Threshold for Channel 11 & 23 in Window Compare
xxxx
ADC1BUF12
318h
A/D Data Buffer 12/Threshold for Channel 12/Threshold for Channel 0 & 12 in Window Compare
xxxx
ADC1BUF13
31Ah
A/D Data Buffer 13/Threshold for Channel 13/Threshold for Channel 1 & 13 in Window Compare
xxxx
ADC1BUF14
31Ch
A/D Data Buffer 14/Threshold for Channel 14/Threshold for Channel 2 & 14 in Window Compare
xxxx
ADC1BUF15
31Eh
A/D Data Buffer 15/Threshold for Channel 15/Threshold for Channel 3 & 15 in Window Compare
xxxx
ADC1BUF16
320h
A/D Data Buffer 16/Threshold for Channel 16/Threshold for Channel 4 & 16 in Window Compare
xxxx
ADC1BUF17
322h
A/D Data Buffer 17/Threshold for Channel 17/Threshold for Channel 5 & 17 in Window Compare
xxxx
ADC1BUF18
324h
A/D Data Buffer 18/Threshold for Channel 18/Threshold for Channel 6 & 18 in Window Compare
xxxx
ADC1BUF19
326h
A/D Data Buffer 19/Threshold for Channel 19/Threshold for Channel 7 & 19 in Window Compare
xxxx
ADC1BUF20
328h
A/D Data Buffer 20/Threshold for Channel 20/Threshold for Channel 8 & 20 in Window Compare
xxxx
ADC1BUF21
32Ah
A/D Data Buffer 21/Threshold for Channel 21/Threshold for Channel 9 & 21 in Window Compare
xxxx
ADC1BUF22
32Ch
A/D Data Buffer 22/Threshold for Channel 22/Threshold for Channel 10 & 22 in Window Compare
xxxx
ADC1BUF23
32Eh
A/D Data Buffer 23/Threshold for Channel 23/Threshold for Channel 11 & 23 in Window Compare
AD1CON1
340h
ADON
—
ADSIDL
—
—
MODE12
FORM1
FORM0
SSRC3
SSRC2
SSRC1
SSRC0
—
ASAM
SAMP
DONE
0000
AD1CON2
342h
PVCFG1
PVCFG0
NVCFG0
—
BUFREGEN
CSCNA
—
—
BUFS
SMPI4
SMPI3
SMPI2
SMPI1
SMPI0
BUFM
ALTS
0000
AD1CON3
344h
ADRC
EXTSAM
—
SAMC4
SAMC3
SAMC2
SAMC1
SAMC0
ADCS7
ADCS6
ADCS5
ADCS4
ADCS3
ADCS2
ADCS1
ADCS0
0000
AD1CHS
348h
CH0NB2
CH0NB1
CH0NB0
CH0SB4
CH0SB3
CH0SB2
CH0SB1
CH0SB0
CH0NA2
CH0NA1
CH0NA0
CH0SA4
CH0SA3
CH0SA2
CH0SA1
CH0SA0
0000
AD1CSSH
34Eh
—
CSS30
CSS29
CSS28
CSS27
CSS26
—
—
CSS23
CSS22
CSS21
CSS20(1)
CSS19(1)
CSS18
CSS17
CSS16
0000
AD1CSSL
350h
CSS15
CSS14
CSS13
CSS12
CSS11
CSS10
CSS9
CSS8(1,2)
CSS7(1,2)
CSS6(1,2)
CSS5(1)
CSS4
CSS3
CSS2
CSS1
CSS0
0000
AD1CON5
354h
ASEN
LPEN
CTMREQ
BGREQ
—
—
ASINT1
ASINT0
—
—
—
—
WM1
WM0
CM1
CM0
0000
AD1CHITH
356h
—
—
—
—
—
—
—
—
CHH23
CHH22
CHH21
CHH20(1)
CHH19(1)
CHH18
CHH17
CHH16
0000
AD1CHITL
358h
CHH15
CHH14
CHH13
CHH12
CHH11
CHH10
CHH9
CHH8(1,2)
CHH7(1,2)
CHH6(1,2)
CHH5(1)
CHH4
CHH3
CHH2
CHH1
CHH0
0000
—
—
—
—
—
—
—
—
CTMEN23
CTMEN22
AD1CTMENL
Legend:
Note 1:
2:
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 3
Bit 2
Bit 1
Bit 0
xxxx
CTMEN21 CTMEN20(1) CTMEN19(1) CTMEN18 CTMEN17 CTMEN16
362h CTMEN15 CTMEN14 CTMEN13 CTMEN12 CTMEN11 CTMEN10 CTMEN9 CTMEN8((1,2) CTMEN7(1,2) CTMEN6(1,2) CTMEN5(1)
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These bits are not implemented in 20-pin devices.
These bits are not implemented in 28-pin devices.
Bit 4
CTMEN4
CTMEN3
CTMEN2
CTMEN1
CTMEN0
0000
0000
PIC24FV16KM204 FAMILY
Advance Information
Addr.
AD1CTMENH 360h
Bit 15
All
Resets
File Name
CTMU REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
CTMUCON1L
35Ah
CTMUEN
—
CTMUSIDL
TGEN
EDGEN
EDGSEQEN
IDISSEN
CTTRIG
ITRIM5
ITRIM4
ITRIM3
ITRIM2
ITRIM1
ITRIM0
IRNG1
IRNG0
0000
—
—
0000
CTMUCON1H 35Ch EDG1MOD EDG1POL EDG1SEL3 EDG1SEL2 EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT EDG2MOD EDG2POL EDG2SEL3 EDG2SEL2 EDG2SEL1 EDG2SEL0
CTMUCON2L
Legend:
35Eh
—
—
—
—
—
—
—
—
—
—
IRSTEN
—
DISCHS2
DISCHS1 DISCHS0
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
TABLE 4-27:
File
Name
—
ANSEL REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
4E0h
—
—
—
—
—
—
—
—
—
—
—
ANSA4(2)
ANSA3
ANSA2
ANSA1
ANSA0
001F(1)
ANSB7
ANSB6(2)
ANSB5(2)
ANSB4
ANSB3(2)
ANSB2
ANSB1
ANSB0
F3FF(1)
—
ANSC2(2,3)
ANSC1(2,3)
ANSC0(2,3)
0007(1)
ANSA
ANSB
4E2h
ANSB15
ANSB12
Advance Information
620h
ALCFGRPT
622h
—
—
ANSB9
—
ANSB8
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
Reset value depends on the device type; the PIC24F16KM204 value is shown.
These bits are not implemented in 20-pin devices.
These bits are not implemented in 28-pin devices.
ALRMVAL
—
—
Legend:
Note 1:
2:
3:
Addr.
—
—
4E4h
File Name
—
ANSB13
ANSC
TABLE 4-28:
—
ANSB14
—
—
—
—
—
REAL-TIME CLOCK AND CALENDAR REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
ALRMEN
CHIME
AMASK3
AMASK2
AMASK1
—
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Alarm Value High Register Window Based on APTR<1:0>
AMASK0
ALRMPTR1
ALRMPTR0
ARPT7
ARPT6
All
Resets
xxxx
ARPT5
ARPT4 ARPT3 ARPT2 ARPT1 ARPT0
RTCVAL
624h
RCFGCAL
626h
RTCEN
RTCWREN RTCSYNC
HALFSEC
RTCOE
RTCPTR1
RTCPTR0
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
0000(1)
RTCPWC
628h
PWCEN PWCPOL PWCCPRE PWCSPRE
RTCCLK1
RTCCLK0
RTCOUT1
RTCOUT0
—
—
—
—
—
—
—
—
0000(1)
 2013 Microchip Technology Inc.
Legend:
Note 1:
RTCC Value High Register Window Based on RTCPTR<1:0>
0000(1)
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
Values are reset only on a VDD POR event.
xxxx
PIC24FV16KM204 FAMILY
DS33030A-page 60
TABLE 4-26:
 2013 Microchip Technology Inc.
TABLE 4-29:
File Name
COMPARATOR REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
CMSTAT
630h
CMIDL
—
—
—
C1EVT
—
—
—
—
—
CVRCON
632h
—
—
—
—
—
—
—
—
CVREN
CVROE
CVRSS
CVR4
CVR3
CVR2
CVR1
CVR0
0000
CM1CON
634h
CON
COE
CPOL
CLPWR
—
—
CEVT
COUT
EVPOL1
EVPOL0
—
CREF1
CREF0
—
CCH1
CCH0
0000
CM2CON(1)
636h
CON
COE
CPOL
CLPWR
—
—
CEVT
COUT
EVPOL1
EVPOL0
—
CREF1(1)
CREF0
—
CCH1
CCH0
0000
CM3CON(1)
638h
CON
COE
CPOL
CLPWR
—
—
CEVT
COUT
EVPOL1
EVPOL0
—
CREF1(1)
CREF0
—
CCH1
CCH0
0000
Legend:
Note 1:
Legend:
Bit 9
C3EVT(1) C2EVT(1)
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
C3OUT(1) C2OUT(1) C1OUT
0000
BAND GAP BUFFER CONTROL REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
670h
—
—
—
—
—
—
—
—
—
—
—
—
—
—
BUFREF1
BUFREF0
0001
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
DS33030A-page 61
PIC24FV16KM204 FAMILY
Advance Information
BUFCON
Bit 10
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These registers and bits are available only on PIC24F(V)16KM2XX devices.
TABLE 4-30:
File Name
Bit 11
All
Resets
Addr.
File Name
CLOCK CONTROL REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
PMSLP
EXTR
SWR
RCON
740h
TRAPR
IOPUWR
SBOREN
RETEN
—
—
CM
OSCCON
742h
—
COSC2
COSC1
COSC0
—
NOSC2
NOSC1
RCDIV1 RCDIV0
CLKDIV
744h
ROI
DOZE2
DOZE1
DOZE0
DOZEN
RCDIV2
OSCTUN
748h
—
—
—
—
—
—
REFOCON
74Eh
ROEN
—
ROSSLP
ROSEL
RODIV3
RODIV2
756h
HLVDEN
—
HLSIDL
—
—
—
HLVDCON
Legend:
Note 1:
2:
—
SWDTEN WDTO
—
LOCK
SLEEP
—
CF
Bit 2
Bit 1
Bit 0
All
Resets
IDLE
BOR
POR
(Note 1)
SOSCDRV SOSCEN OSWEN (Note 2)
—
—
—
—
—
—
—
—
—
TUN5
TUN4
TUN3
TUN2
TUN1
TUN0
0000
—
—
—
—
—
—
—
—
0000
VDIR
BGVST
IRVST
—
HLVDL3
HLVDL2
HLVDL1
HLVDL0
0000
RODIV1 RODIV0
—
Bit 3
—
—
—
Bit 4
0100
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
RCON register Reset values are dependent on the type of Reset.
OSCCON register Reset values are dependent on Configuration fuses and by type of Reset.
TABLE 4-32:
NVM REGISTER MAP
Advance Information
File Name
Addr.
Bit 15
Bit 14
NVMCON
760h
WR
WREN
NVMKEY
766h
—
—
Legend:
NOSC0 CLKLOCK
Bit 5
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
—
—
—
—
—
—
—
—
WRERR PGMONLY
—
—
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
ERASE
NVMOP5
NVMOP4
NVMOP3
NVMOP2
NVMOP1
NVMOP0
0000
NVMKEY7 NVMKEY6 NVMKEY5 NVMKEY4 NVMKEY3 NVMKEY2 NVMKEY1 NVMKEY0
0000
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
TABLE 4-33:
ULTRA LOW-POWER WAKE-UP REGISTER MAP
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
ULPWCON
768h
ULPEN
—
ULPSIDL
—
—
—
—
ULPSINK
—
—
—
—
—
—
—
—
0000
Bit 0
All
Resets
0000
Legend:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
TABLE 4-34:
 2013 Microchip Technology Inc.
File
Name
PMD REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
PMD1
770h
—
—
—
—
T1MD
—
—
—
SSP1MD
U2MD(1)
U1MD
PMD2
772h
—
—
—
—
—
—
—
—
—
—
—
PMD3
774h
—
—
—
—
—
CMPMD
RTCCMD
—
—
DAC1MD(1)
—
—
—
PMD4
776h
—
—
—
—
—
—
—
—
—
ULPWUMD
—
—
REFOMD
PMD6
77Ah
—
—
—
—
—
—
—
—
—
—
PMD8
77Eh
—
—
—
—
—
—
—
—
—
—
Legend:
Note 1:
Bit 4
Bit 3
Bit 2
—
—
—
—
—
ADCMD
CCP2MD
CCP1MD
0000
—
SSP2MD(1)
—
0000
CTMUMD
HLVDMD
—
0000
—
—
—
0000
CLC1MD
—
—
0000
CCP5MD(1) CCP4MD(1) CCP3MD(1)
AMP1MD(1) DAC2MD(1) AMP2MD(1)
—
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
These bits are available only on PIC24F(V)16KM2XX devices.
CLC2MD(1)
Bit 1
PIC24FV16KM204 FAMILY
DS33030A-page 62
TABLE 4-31:
PIC24FV16KM204 FAMILY
4.2.5
4.3
SOFTWARE STACK
In addition to its use as a working register, the W15
register in PIC24F devices is also used as a Software
Stack Pointer. The pointer always points to the first
available free word and grows from lower to higher
addresses. It pre-decrements for stack pops and
post-increments for stack pushes, as depicted in
Figure 4-4.
For a PC push during any CALL instruction, the MSB of
the PC is zero-extended before the push, ensuring that
the MSB is always clear.
Note:
A PC push during exception processing
will concatenate the SRL register to the
MSB of the PC prior to the push.
The Stack Pointer Limit Value (SPLIM) register,
associated with the Stack Pointer, sets an upper
address boundary for the stack. SPLIM is uninitialized
at Reset. As is the case for the Stack Pointer,
SPLIM<0> is forced to ‘0’ as all stack operations must
be word-aligned. Whenever an EA is generated using
W15 as a source or destination pointer, the resulting
address is compared with the value in SPLIM. If the
contents of the Stack Pointer (W15) and the SPLIM
register are equal, and a push operation is performed,
a stack error trap will not occur. The stack error trap will
occur on a subsequent push operation.
Thus, for example, if it is desirable to cause a stack
error trap when the stack grows beyond address, 0DF6
in RAM, initialize the SPLIM with the value, 0DF4.
Similarly, a Stack Pointer underflow (stack error) trap is
generated when the Stack Pointer address is found to
be less than 0800h. This prevents the stack from
interfering with the Special Function Register (SFR)
space.
Note:
A write to the SPLIM register should not
be immediately followed by an indirect
read operation using W15.
FIGURE 4-4:
Stack Grows Towards
Higher Address
0000h
CALL STACK FRAME
15
0
PC<15:0>
W15 (before CALL)
000000000 PC<22:16>
<Free Word>
W15 (after CALL)
POP : [--W15]
PUSH : [W15++]
 2013 Microchip Technology Inc.
Interfacing Program and Data
Memory Spaces
The PIC24F architecture uses a 24-bit-wide program
space and 16-bit wide data space. The architecture is
also a modified Harvard scheme, meaning that data
can also be present in the program space. To use this
data successfully, it must be accessed in a way that
preserves the alignment of information in both spaces.
Apart from the normal execution, the PIC24F
architecture provides two methods by which the
program space can be accessed during operation:
• Using table instructions to access individual bytes
or words anywhere in the program space
• Remapping a portion of the program space into
the data space, PSV
Table instructions allow an application to read or write
small areas of the program memory. This makes the
method ideal for accessing data tables that need to be
updated from time to time. It also allows access to all
bytes of the program word. The remapping method
allows an application to access a large block of data on
a read-only basis, which is ideal for look ups from a
large table of static data. It can only access the least
significant word (lsw) of the program word.
4.3.1
ADDRESSING PROGRAM SPACE
Since the address ranges for the data and program
spaces are 16 and 24 bits, respectively, a method is
needed to create a 23-bit or 24-bit program address
from 16-bit data registers. The solution depends on the
interface method to be used.
For table operations, the 8-bit Table Memory Page
Address register (TBLPAG) is used to define a 32K word
region within the program space. This is concatenated
with a 16-bit EA to arrive at a full 24-bit program space
address. In this format, the Most Significant bit (MSb) of
TBLPAG is used to determine if the operation occurs in
the user memory (TBLPAG<7> = 0) or the configuration
memory (TBLPAG<7> = 1).
For remapping operations, the 8-bit Program Space
Visibility Page Address register (PSVPAG) is used to
define a 16K word page in the program space. When
the MSb of the EA is ‘1’, PSVPAG is concatenated with
the lower 15 bits of the EA to form a 23-bit program
space address. Unlike the table operations, this limits
remapping operations strictly to the user memory area.
See Table 4-35 and Figure 4-5 to know how the program EA is created for table operations and remapping
accesses from the data EA. Here, P<23:0> refers to a
program space word, whereas D<15:0> refers to a data
space word.
Advance Information
DS33030A-page 63
PIC24FV16KM204 FAMILY
TABLE 4-35:
PROGRAM SPACE ADDRESS CONSTRUCTION
Program Space Address
Access
Space
Access Type
<23>
<22:16>
<15>
<14:1>
<0>
Instruction Access
(Code Execution)
User
TBLRD/TBLWT
(Byte/Word Read/Write)
User
TBLPAG<7:0>
Data EA<15:0>
0xxx xxxx
xxxx xxxx xxxx xxxx
Configuration
TBLPAG<7:0>
Data EA<15:0>
1xxx xxxx
xxxx xxxx xxxx xxxx
2:
0
0xx xxxx xxxx xxxx xxxx xxx0
Program Space Visibility
(Block Remap/Read)
Note 1:
PC<22:1>
0
User
0
PSVPAG<7:0>(2)
Data EA<14:0>(1)
0
xxxx xxxx
xxx xxxx xxxx xxxx
Data EA<15> is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of
the address is PSVPAG<0>.
PSVPAG can have only two values (‘00’ to access program memory and FF to access data EEPROM) on
the PIC24F16KM family.
FIGURE 4-5:
DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION
Program Counter(1)
Program Counter
0
0
23 Bits
EA
Table Operations(2)
1/0
TBLPAG
1/0
8 Bits
16 Bits
24 Bits
Select
Program Space Visibility(1)
(Remapping)
0
1
EA
0
PSVPAG
8 Bits
15 Bits
23 Bits
User/Configuration
Space Select
Note 1:
2:
Byte Select
The LSb of program space addresses is always fixed as ‘0’ in order to maintain word alignment of data in the
program and data spaces.
Table operations are not required to be word-aligned. Table Read operations are permitted in the configuration
memory space.
DS33030A-page 64
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
4.3.2
DATA ACCESS FROM PROGRAM
MEMORY AND DATA EEPROM
MEMORY USING TABLE
INSTRUCTIONS
The TBLRDL and TBLWTL instructions offer a direct
method of reading or writing the lower word of any
address within the program memory without going
through data space. It also offers a direct method of
reading or writing a word of any address within data
EEPROM memory. The TBLRDH and TBLWTH instructions are the only method to read or write the upper 8 bits
of a program space word as data.
Note: The TBLRDH and TBLWTH instructions are not
used while accessing data EEPROM memory.
The PC is incremented by 2 for each successive
24-bit program word. This allows program memory
addresses to directly map to data space addresses.
Program memory can thus be regarded as two 16-bit,
word-wide address spaces, residing side by side, each
with the same address range. TBLRDL and TBLWTL
access the space which contains the least significant
data word, and TBLRDH and TBLWTH access the space
which contains the upper data byte.
Two table instructions are provided to move byte or
word-sized (16-bit) data to and from program space.
Both function as either byte or word operations.
1.
In Byte mode, either the upper or lower byte of
the lower program word is mapped to the lower
byte of a data address. The upper byte is
selected when byte select is ‘1’; the lower byte
is selected when it is ‘0’.
2.
In Byte mode, it maps the upper or lower byte of
the program word to D<7:0> of the data
address, as above. Note that the data will
always be ‘0’ when the upper ‘phantom’ byte is
selected (byte select = 1).
In a similar fashion, two table instructions, TBLWTH
and TBLWTL, are used to write individual bytes or
words to a program space address. The details of
their operation are explained in Section 5.0 “Flash
Program Memory”.
For all table operations, the area of program memory
space to be accessed is determined by the Table
Memory Page Address register (TBLPAG). TBLPAG
covers the entire program memory space of the
device, including user and configuration spaces. When
TBLPAG<7> = 0, the table page is located in the user
memory space. When TBLPAG<7> = 1, the page is
located in configuration space.
TBLRDL (Table Read Low): In Word mode, it
maps the lower word of the program space
location (P<15:0>) to a data address (D<15:0>).
FIGURE 4-6:
TBLRDH (Table Read High): In Word mode, it
maps the entire upper word of a program address
(P<23:16>) to a data address. Note that
D<15:8>, the ‘phantom’ byte, will always be ‘0’.
Note: Only Table Read operations will execute in the
configuration memory space, and only then, in
implemented areas, such as the Device ID.
Table Write operations are not allowed.
ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS
Program Space
Data EA<15:0>
TBLPAG
23
00
23
15
0 000000h
16
8
0
00000000
00000000
00000000
002BFEh
00000000
‘Phantom’ Byte
TBLRDH.B (Wn<0> = 0)
TBLRDL.B (Wn<0> = 1)
TBLRDL.B (Wn<0> = 0)
TBLRDL.W
800000h
 2013 Microchip Technology Inc.
The address for the table operation is determined by the data EA
within the page defined by the TBLPAG register. Only read
operations are provided; write operations are also valid in the
user memory area.
Advance Information
DS33030A-page 65
PIC24FV16KM204 FAMILY
4.3.3
READING DATA FROM PROGRAM
MEMORY USING PROGRAM SPACE
VISIBILITY
The upper 32 Kbytes of data space may optionally be
mapped into a 16K word page of the program space.
This provides transparent access of stored constant
data from the data space without the need to use
special instructions (i.e., TBLRDL/H).
Program space access through the data space occurs
if the MSb of the data space, EA, is ‘1’, and PSV is
enabled by setting the PSV bit in the CPU Control
(CORCON<2>) register. The location of the program
memory space to be mapped into the data space is
determined by the Program Space Visibility Page
Address register (PSVPAG). This 8-bit register defines
any one of 256 possible pages of 16K words in program
space. In effect, PSVPAG functions as the upper 8 bits
of the program memory address, with the 15 bits of the
EA functioning as the lower bits.
By incrementing the PC by 2 for each program memory
word, the lower 15 bits of data space addresses directly
map to the lower 15 bits in the corresponding program
space addresses.
Data reads from this area add an additional cycle to the
instruction being executed, since two program memory
fetches are required.
Although each data space address, 8000h and higher,
maps directly into a corresponding program memory
address (see Figure 4-7), only the lower 16 bits of the
FIGURE 4-7:
24-bit program word are used to contain the data. The
upper 8 bits of any program space locations used as
data should be programmed with ‘1111 1111’ or ‘0000
0000’ to force a NOP. This prevents possible issues
should the area of code ever be accidentally executed.
Note:
PSV access is temporarily disabled during
Table Reads/Writes.
For operations that use PSV and are executed outside
a REPEAT loop, the MOV and MOV.D instructions will
require one instruction cycle in addition to the specified
execution time. All other instructions will require two
instruction cycles in addition to the specified execution
time.
For operations that use PSV, which are executed inside
a REPEAT loop, there will be some instances that
require two instruction cycles in addition to the
specified execution time of the instruction:
• Execution in the first iteration
• Execution in the last iteration
• Execution prior to exiting the loop due to an
interrupt
• Execution upon re-entering the loop after an
interrupt is serviced
Any other iteration of the REPEAT loop will allow the
instruction accessing data, using PSV, to execute in a
single cycle.
PROGRAM SPACE VISIBILITY OPERATION
When CORCON<2> = 1 and EA<15> = 1:
Program Space
PSVPAG
00
23
15
Data Space
0
000000h
0000h
Data EA<14:0>
002BFEh
The data in the page
designated by
PSVPAG is mapped
into the upper half of
the data memory
space....
8000h
PSV Area
...while the lower 15 bits
of the EA specify an exact
address within the PSV
FFFFh area. This corresponds
exactly to the same lower
15 bits of the actual
program space address.
800000h
DS33030A-page 66
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
5.0
Note:
FLASH PROGRAM MEMORY
Real-Time Self-Programming (RTSP) is accomplished
using TBLRD (Table Read) and TBLWT (Table Write)
instructions. With RTSP, the user may write program
memory data in blocks of 32 instructions (96 bytes) at a
time, and erase program memory in blocks of 32, 64 and
128 instructions (96,192 and 384 bytes) at a time.
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on Flash programming, refer to the “PIC24F Family
Reference Manual”, Section 4. “Program
Memory” (DS39715).
The NVMOP<1:0> (NVMCON<1:0>) bits decide the
erase block size.
5.1
The PIC24FV16KM204 family of devices contains
internal Flash program memory for storing and executing application code. The memory is readable, writable
and erasable when operating with VDD over 1.8V.
Regardless of the method used, Flash memory
programming is done with the Table Read and Write
instructions. These allow direct read and write access to
the program memory space from the data memory while
the device is in normal operating mode. The 24-bit target
address in the program memory is formed using the
TBLPAG<7:0> bits and the Effective Address (EA) from
a W register, specified in the table instruction, as
depicted in Figure 5-1.
Flash memory can be programmed in three ways:
• In-Circuit Serial Programming™ (ICSP™)
• Run-Time Self-Programming (RTSP)
• Enhanced In-Circuit Serial Programming
(Enhanced ICSP)
ICSP allows a PIC24FV16KM204 device to be serially
programmed while in the end application circuit. This is
simply done with two lines for the programming clock
and programming data (which are named PGCx and
PGDx, respectively), and three other lines for power
(VDD), ground (VSS) and Master Clear/Program Mode
Entry Voltage (MCLR/VPP). This allows customers to
manufacture boards with unprogrammed devices and
then program the microcontroller just before shipping
the product. This also allows the most recent firmware
or custom firmware to be programmed.
FIGURE 5-1:
Table Instructions and Flash
Programming
The TBLRDL and the TBLWTL instructions are used to
read or write to bits<15:0> of program memory.
TBLRDL and TBLWTL can access program memory in
both Word and Byte modes.
The TBLRDH and TBLWTH instructions are used to read
or write to bits<23:16> of program memory. TBLRDH
and TBLWTH can also access program memory in Word
or Byte mode.
ADDRESSING FOR TABLE REGISTERS
24 Bits
Using
Program
Counter
Program Counter
0
0
Working Reg EA
Using
Table
Instruction
User/Configuration
Space Select
 2013 Microchip Technology Inc.
1/0
TBLPAG Reg
8 Bits
16 Bits
24-Bit EA
Advance Information
Byte
Select
DS33030A-page 67
PIC24FV16KM204 FAMILY
5.2
RTSP Operation
5.3
The PIC24F Flash program memory array is organized
into rows of 32 instructions or 96 bytes. RTSP allows
the user to erase blocks of 1 row, 2 rows and 4 rows
(32, 64 and 128 instructions) at a time, and to program
one row at a time. It is also possible to program single
words.
The 1-row (96 bytes), 2-row (192 bytes) and 4-row
(384 bytes) erase blocks, and single row write block
(96 bytes) are edge-aligned, from the beginning of
program memory.
When data is written to program memory using TBLWT
instructions, the data is not written directly to memory.
Instead, data written using Table Writes is stored in holding
latches until the programming sequence is executed.
Any number of TBLWT instructions can be executed
and a write will be successfully performed. However,
32 TBLWT instructions are required to write the full row
of memory.
The basic sequence for RTSP programming is to set up
a Table Pointer, then do a series of TBLWT instructions to
load the buffers. Programming is performed by setting
the control bits in the NVMCON register.
Data can be loaded in any order and the holding registers can be written to multiple times before performing
a write operation. Subsequent writes, however, will
wipe out any previous writes.
Note:
Writing to a location multiple times, without erasing it, is not recommended.
All of the Table Write operations are single-word writes
(two instruction cycles), because only the buffers are written. A programming cycle is required for programming
each row.
DS33030A-page 68
Enhanced In-Circuit Serial
Programming
Enhanced ICSP uses an on-board bootloader, known
as the Program Executive (PE), to manage the programming process. Using an SPI data frame format,
the Program Executive can erase, program and verify
program memory. For more information on Enhanced
ICSP, see the device programming specification.
5.4
Control Registers
There are two SFRs used to read and write the
program Flash memory: NVMCON and NVMKEY.
The NVMCON register (Register 5-1) controls the
blocks that need to be erased, which memory type is to
be programmed and when the programming cycle
starts.
NVMKEY is a write-only register that is used for write
protection. To start a programming or erase sequence,
the user must consecutively write 55h and AAh to the
NVMKEY register. Refer to Section 5.5 “Programming
Operations” for further details.
5.5
Programming Operations
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode. During a programming or erase operation, the
processor stalls (waits) until the operation is finished.
Setting the WR bit (NVMCON<15>) starts the
operation and the WR bit is automatically cleared when
the operation is finished.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 5-1:
NVMCON: FLASH MEMORY CONTROL REGISTER
R/SO-0, HC
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
WR
WREN
WRERR
PGMONLY(4)
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
ERASE
NVMOP5(1)
NVMOP4(1)
NVMOP3(1)
NVMOP2(1)
NVMOP1(1)
NVMOP0(1)
bit 7
bit 0
Legend:
SO = Settable Only bit
HC = Hardware Clearable bit
-n = Value at POR
‘1’ = Bit is set
R = Readable bit
‘0’ = Bit is cleared
x = Bit is unknown
U = Unimplemented bit, read as ‘0’
W = Writable bit
bit 15
WR: Write Control bit
1 = Initiates a Flash memory program or erase operation; the operation is self-timed and the bit is
cleared by hardware once the operation is complete
0 = Program or erase operation is complete and inactive
bit 14
WREN: Write Enable bit
1 = Enables Flash program/erase operations
0 = Inhibits Flash program/erase operations
bit 13
WRERR: Write Sequence Error Flag bit
1 = An improper program or erase sequence attempt, or termination has occurred (bit is set automatically
on any set attempt of the WR bit)
0 = The program or erase operation completed normally
bit 12
PGMONLY: Program Only Enable bit(4)
bit 11-7
Unimplemented: Read as ‘0’
bit 6
ERASE: Erase/Program Enable bit
1 = Perform the erase operation specified by the NVMOP<5:0> bits on the next WR command
0 = Perform the program operation specified by the NVMOP<5:0> bits on the next WR command
bit 5-0
NVMOP<5:0>: Programming Operation Command Byte bits(1)
Erase Operations (when ERASE bit is ‘1’):
1010xx = Erase entire boot block (including code-protected boot block)(2)
1001xx = Erase entire memory (including boot block, configuration block, general block)(2)
011010 = Erase 4 rows of Flash memory(3)
011001 = Erase 2 rows of Flash memory(3)
011000 = Erase 1 row of Flash memory(3)
0101xx = Erase entire configuration block (except code protection bits)
0100xx = Erase entire data EEPROM(4)
0011xx = Erase entire general memory block programming operations
0001xx = Write 1 row of Flash memory (when ERASE bit is ‘0’)(3)
Note 1:
2:
3:
4:
All other combinations of NVMOP<5:0> are no operation.
Available in ICSP™ mode only. Refer to the device programming specification.
The address in the Table Pointer decides which rows will be erased.
This bit is used only while accessing data EEPROM.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 69
PIC24FV16KM204 FAMILY
5.5.1
PROGRAMMING ALGORITHM FOR
FLASH PROGRAM MEMORY
4.
5.
The user can program one row of Flash program
memory at a time by erasing the programmable row.
The general process is:
1.
2.
3.
Read a row of program memory (32 instructions)
and store in data RAM.
Update the program data in RAM with the
desired new data.
Erase a row (see Example 5-1):
a) Set the NVMOP bits (NVMCON<5:0>) to
‘011000’ to configure for row erase. Set the
ERASE (NVMCON<6>) and WREN
(NVMCON<14>) bits.
b) Write the starting address of the block to be
erased into the TBLPAG and W registers.
c) Write 55h to NVMKEY.
d) Write AAh to NVMKEY.
e) Set the WR bit (NVMCON<15>). The erase
cycle begins and the CPU stalls for the
duration of the erase cycle. When the erase is
done, the WR bit is cleared automatically.
EXAMPLE 5-1:
EXAMPLE 5-2:
For protection against accidental operations, the write
initiate sequence for NVMKEY must be used to allow
any erase or program operation to proceed. After the
programming command has been executed, the user
must wait for the programming time until programming
is complete. The two instructions following the start of
the programming sequence should be NOPs, as
displayed in Example 5-5.
ERASING A PROGRAM MEMORY ROW – ASSEMBLY LANGUAGE CODE
; Set up NVMCON for row erase operation
MOV
#0x4058, W0
MOV
W0, NVMCON
; Init pointer to row to be ERASED
MOV
#tblpage(PROG_ADDR), W0
MOV
W0, TBLPAG
MOV
#tbloffset(PROG_ADDR), W0
TBLWTL W0, [W0]
DISI
#5
MOV
MOV
MOV
MOV
BSET
NOP
NOP
Write the first 32 instructions from data RAM into
the program memory buffers (see Example 5-1).
Write the program block to Flash memory:
a) Set the NVMOP bits to ‘000100’ to
configure for row programming. Clear the
ERASE bit and set the WREN bit.
b) Write 55h to NVMKEY.
c) Write AAh to NVMKEY.
d) Set the WR bit. The programming cycle
begins and the CPU stalls for the duration
of the write cycle. When the write to Flash
memory is done, the WR bit is cleared
automatically.
#0x55, W0
W0, NVMKEY
#0xAA, W1
W1, NVMKEY
NVMCON, #WR
;
; Initialize NVMCON
;
;
;
;
;
;
;
;
;
;
;
Initialize PM Page Boundary SFR
Initialize in-page EA[15:0] pointer
Set base address of erase block
Block all interrupts
for next 5 instructions
Write the 55 key
Write the AA key
Start the erase sequence
Insert two NOPs after the erase
command is asserted
ERASING A PROGRAM MEMORY ROW – ‘C’ LANGUAGE CODE
// C example using MPLAB C30
int __attribute__ ((space(auto_psv))) progAddr = 0x1234;
// Variable located in Pgm Memory, declared as a
// global variable
unsigned int offset;
//Set up pointer to the first memory location to be written
TBLPAG = __builtin_tblpage(&progAddr);
offset = __builtin_tbloffset(&progAddr);
// Initialize PM Page Boundary SFR
// Initialize lower word of address
__builtin_tblwtl(offset, 0x0000);
// Set base address of erase block
// with dummy latch write
NVMCON = 0x4058;
// Initialize NVMCON
asm("DISI #5");
__builtin_write_NVM();
// Block all interrupts for next 5 instructions
// C30 function to perform unlock
// sequence and set WR
DS33030A-page 70
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
EXAMPLE 5-3:
LOADING THE WRITE BUFFERS – ASSEMBLY LANGUAGE CODE
; Set up NVMCON for row programming operations
MOV
#0x4004, W0
;
MOV
W0, NVMCON
; Initialize NVMCON
; Set up a pointer to the first program memory location to be written
; program memory selected, and writes enabled
MOV
#0x0000, W0
;
MOV
W0, TBLPAG
; Initialize PM Page Boundary SFR
MOV
#0x1500, W0
; An example program memory address
; Perform the TBLWT instructions to write the latches
; 0th_program_word
MOV
#LOW_WORD_0, W2
;
MOV
#HIGH_BYTE_0, W3
;
TBLWTL W2, [W0]
; Write PM low word into program latch
TBLWTH W3, [W0++]
; Write PM high byte into program latch
; 1st_program_word
MOV
#LOW_WORD_1, W2
;
MOV
#HIGH_BYTE_1, W3
;
TBLWTL W2, [W0]
; Write PM low word into program latch
TBLWTH W3, [W0++]
; Write PM high byte into program latch
; 2nd_program_word
MOV
#LOW_WORD_2, W2
;
MOV
#HIGH_BYTE_2, W3
;
; Write PM low word into program latch
TBLWTL W2, [W0]
; Write PM high byte into program latch
TBLWTH W3, [W0++]
•
•
•
; 32nd_program_word
MOV
#LOW_WORD_31, W2
;
MOV
#HIGH_BYTE_31, W3
;
; Write PM low word into program latch
TBLWTL W2, [W0]
; Write PM high byte into program latch
TBLWTH W3, [W0]
EXAMPLE 5-4:
LOADING THE WRITE BUFFERS – ‘C’ LANGUAGE CODE
// C example using MPLAB C30
#define NUM_INSTRUCTION_PER_ROW 64
int __attribute__ ((space(auto_psv))) progAddr = 0x1234
unsigned int offset;
unsigned int i;
unsigned int progData[2*NUM_INSTRUCTION_PER_ROW];
//Set up NVMCON for row programming
NVMCON = 0x4004;
// Variable located in Pgm Memory
// Buffer of data to write
// Initialize NVMCON
//Set up pointer to the first memory location to be written
TBLPAG = __builtin_tblpage(&progAddr);
// Initialize PM Page Boundary SFR
// Initialize lower word of address
offset = __builtin_tbloffset(&progAddr);
//Perform TBLWT instructions to write necessary number of latches
for(i=0; i < 2*NUM_INSTRUCTION_PER_ROW; i++)
{
__builtin_tblwtl(offset, progData[i++]);
// Write to address low word
__builtin_tblwth(offset, progData[i]);
// Write to upper byte
offset = offset + 2;
// Increment address
}
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 71
PIC24FV16KM204 FAMILY
EXAMPLE 5-5:
INITIATING A PROGRAMMING SEQUENCE – ASSEMBLY LANGUAGE CODE
DISI
#5
; Block all interrupts
for next 5 instructions
MOV
MOV
MOV
MOV
BSET
NOP
NOP
BTSC
BRA
#0x55, W0
W0, NVMKEY
#0xAA, W1
W1, NVMKEY
NVMCON, #WR
NVMCON, #15
$-2
EXAMPLE 5-6:
;
;
;
;
;
;
;
;
Write the 55 key
Write the AA key
Start the erase sequence
2 NOPs required after setting WR
Wait for the sequence to be completed
INITIATING A PROGRAMMING SEQUENCE – ‘C’ LANGUAGE CODE
// C example using MPLAB C30
asm("DISI #5");
// Block all interrupts for next 5 instructions
__builtin_write_NVM();
// Perform unlock sequence and set WR
DS33030A-page 72
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
6.0
Note:
DATA EEPROM MEMORY
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on
data EEPROM, refer to the “PIC24F
Family Reference Manual”, Section 5.
“Data EEPROM” (DS39720).
The data EEPROM memory is a Nonvolatile Memory
(NVM), separate from the program and volatile data
RAM. Data EEPROM memory is based on the same
Flash technology as program memory, and is optimized
for both long retention and a higher number of
erase/write cycles.
The data EEPROM is mapped to the top of the user program memory space, with the top address at program
memory address, 7FFE00h to 7FFFFFh. The size of the
data EEPROM is 256 words in PIC24FV16KM204
devices.
The data EEPROM is organized as 16-bit-wide
memory. Each word is directly addressable, and is
readable and writable during normal operation over the
entire VDD range.
Unlike the Flash program memory, normal program
execution is not stopped during a data EEPROM
program or erase operation.
The data EEPROM programming operations are
controlled using the three NVM Control registers:
• NVMCON: Nonvolatile Memory Control Register
• NVMKEY: Nonvolatile Memory Key Register
• NVMADR: Nonvolatile Memory Address Register
EXAMPLE 6-1:
6.1
NVMCON Register
The NVMCON register (Register 6-1) is also the primary
control register for data EEPROM program/erase
operations. The upper byte contains the control bits
used to start the program or erase cycle and the flag bit
to indicate if the operation was successfully performed.
The lower byte of NVMCOM configures the type of NVM
operation that will be performed.
6.2
NVMKEY Register
The NVMKEY is a write-only register that is used to
prevent accidental writes or erasures of data EEPROM
locations.
To start any programming or erase sequence, the
following instructions must be executed first, in the
exact order provided:
1.
2.
Write 55h to NVMKEY.
Write AAh to NVMKEY.
After this sequence, a write will be allowed to the
NVMCON register for one instruction cycle. In most
cases, the user will simply need to set the WR bit in the
NVMCON register to start the program or erase cycle.
Interrupts should be disabled during the unlock
sequence.
The MPLAB® C30 C compiler provides a defined library
procedure (builtin_write_NVM) to perform the
unlock sequence. Example 6-1 illustrates how the
unlock sequence can be performed with in-line
assembly.
DATA EEPROM UNLOCK SEQUENCE
//Disable Interrupts For 5 instructions
asm volatile
("disi #5");
//Issue Unlock Sequence
asm volatile
("mov #0x55, W0
\n"
"mov W0, NVMKEY
\n"
"mov #0xAA, W1
\n"
"mov W1, NVMKEY
\n");
// Perform Write/Erase operations
asm volatile
("bset NVMCON, #WR \n"
"nop
\n"
"nop
\n");
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 73
PIC24FV16KM204 FAMILY
REGISTER 6-1:
NVMCON: NONVOLATILE MEMORY CONTROL REGISTER
R/S-0, HC
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
WR
WREN
WRERR
PGMONLY
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
ERASE
NVMOP5
NVMOP4
NVMOP3
NVMOP2
NVMOP1
NVMOP0
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
S = Settable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
WR: Write Control bit (program or erase)
1 = Initiates a data EEPROM erase or write cycle (can be set, but not cleared in software)
0 = Write cycle is complete (cleared automatically by hardware)
bit 14
WREN: Write Enable bit (erase or program)
1 = Enables an erase or program operation
0 = No operation allowed (device clears this bit on completion of the write/erase operation)
bit 13
WRERR: Flash Error Flag bit
1 = A write operation is prematurely terminated (any MCLR or WDT Reset during programming
operation)
0 = The write operation completed successfully
bit 12
PGMONLY: Program Only Enable bit
1 = Write operation is executed without erasing target address(es) first
0 = Automatic erase-before-write
Write operations are preceded automatically by an erase of the target address(es).
bit 11-7
Unimplemented: Read as ‘0’
bit 6
ERASE: Erase Operation Select bit
1 = Performs an erase operation when WR is set
0 = Performs a write operation when WR is set
bit 5-0
NVMOP<5:0>: Programming Operation Command Byte bits
Erase Operations (when ERASE bit is ‘1’):
011010 = Erase 8 words
011001 = Erase 4 words
011000 = Erase 1 word
0100xx = Erase entire data EEPROM
Programming Operations (when ERASE bit is ‘0’):
0010xx = Write 1 word
DS33030A-page 74
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
6.3
NVM Address Register
6.4
As with Flash program memory, the NVM Address
registers, NVMADRU and NVMADR, form the 24-bit
Effective Address (EA) of the selected row or word for
data EEPROM operations. The NVMADRU register is
used to hold the upper 8 bits of the EA, while the
NVMADR register is used to hold the lower 16 bits of
the EA. These registers are not mapped into the
Special Function Register (SFR) space; instead, they
directly capture the EA<23:0> of the last Table Write
instruction that has been executed and selects the data
EEPROM row to erase. Figure 6-1 depicts the program
memory EA that is formed for programming and erase
operations.
Like program memory operations, the Least Significant
bit (LSb) of NVMADR is restricted to even addresses.
This is because any given address in the data EEPROM
space consists of only the lower word of the program
memory width; the upper word, including the uppermost
“phantom byte”, are unavailable. This means that the
LSb of a data EEPROM address will always be ‘0’.
Similarly, the Most Significant bit (MSb) of NVMADRU
is always ‘0’, since all addresses lie in the user program
space.
FIGURE 6-1:
DATA EEPROM
ADDRESSING WITH
TBLPAG AND NVM
ADDRESS REGISTERS
Data EEPROM Operations
The EEPROM block is accessed using Table Read and
Write operations similar to those used for program
memory. The TBLWTH and TBLRDH instructions are not
required for data EEPROM operations since the
memory is only 16 bits wide (data on the lower address
is valid only). The following programming operations
can be performed on the data EEPROM:
•
•
•
•
Erase one, four or eight words
Bulk erase the entire data EEPROM
Write one word
Read one word
Note 1: Unexpected results will be obtained if the
user attempts to read the EEPROM while
a programming or erase operation is
underway.
2: The XC16 C compiler includes library
procedures to automatically perform the
Table Read and Table Write operations,
manage the Table Pointer and write buffers, and unlock and initiate memory
write sequences. This eliminates the
need to create assembler macros or time
critical routines in C for each application.
The library procedures are used in the code examples
detailed in the following sections. General descriptions
of each process are provided for users who are not
using the XC16 compiler libraries.
24-Bit PM Address
0
7Fh
TBLPAG
xxxxh
W Register EA
NVMADRU
NVMADR
 2013 Microchip Technology Inc.
0
Advance Information
DS33030A-page 75
PIC24FV16KM204 FAMILY
6.4.1
ERASE DATA EEPROM
The data EEPROM can be fully erased, or can be
partially erased, at three different sizes: one word, four
words or eight words. The bits, NVMOP<1:0>
(NVMCON<1:0>), decide the number of words to be
erased. To erase partially from the data EEPROM, the
following sequence must be followed:
1.
2.
3.
4.
5.
6.
Configure NVMCON to erase the required
number of words: one, four or eight.
Load TBLPAG and WREG with the EEPROM
address to be erased.
Clear the NVMIF status bit and enable the NVM
interrupt (optional).
Write the key sequence to NVMKEY.
Set the WR bit to begin the erase cycle.
Either poll the WR bit or wait for the NVM
interrupt (NVMIF is set).
EXAMPLE 6-2:
A typical erase sequence is provided in Example 6-2.
This example shows how to do a one-word erase.
Similarly, a four-word erase and an eight-word erase
can be done. This example uses C library procedures to
manage the Table Pointer (builtin_tblpage and
builtin_tbloffset) and the Erase Page Pointer
(builtin_tblwtl). The memory unlock sequence
(builtin_write_NVM) also sets the WR bit to initiate
the operation and returns control when complete.
SINGLE-WORD ERASE
int __attribute__ ((space(eedata))) eeData = 0x1234;
/*-------------------------------------------------------------------------------------------The variable eeData must be a Global variable declared outside of any method
the code following this comment can be written inside the method that will execute the erase
---------------------------------------------------------------------------------------------*/
unsigned int offset;
// Set up NVMCON to erase one word of data EEPROM
NVMCON = 0x4058;
// Set up a pointer to the EEPROM location to be erased
TBLPAG = __builtin_tblpage(&eeData);
// Initialize EE Data page pointer
offset = __builtin_tbloffset(&eeData);
// Initizlize lower word of address
__builtin_tblwtl(offset, 0);
// Write EEPROM data to write latch
asm volatile ("disi #5");
__builtin_write_NVM();
while(NVMCONbits.WR=1);
DS33030A-page 76
//
//
//
//
Disable Interrupts For 5 Instructions
Issue Unlock Sequence & Start Write Cycle
Optional: Poll WR bit to wait for
write sequence to complete
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
6.4.1.1
Data EEPROM Bulk Erase
6.4.2
SINGLE-WORD WRITE
To erase the entire data EEPROM (bulk erase), the
address registers do not need to be configured
because this operation affects the entire data
EEPROM. The following sequence helps in performing
a bulk erase:
To write a single word in the data EEPROM, the
following sequence must be followed:
1.
2.
2.
3.
3.
4.
5.
Configure NVMCON to Bulk Erase mode.
Clear the NVMIF status bit and enable the NVM
interrupt (optional).
Write the key sequence to NVMKEY.
Set the WR bit to begin the erase cycle.
Either poll the WR bit or wait for the NVM
interrupt (NVMIF is set).
1.
A typical bulk erase sequence is provided in
Example 6-3.
Erase one data EEPROM word (as mentioned in
the previous section) if the PGMONLY bit
(NVMCON<12>) is set to ‘1’.
Write the data word into the data EEPROM latch.
Program the data word into the EEPROM:
- Configure the NVMCON register to
program one EEPROM word
(NVMCON<5:0> = 0001xx).
- Clear the NVMIF status bit and enable the NVM
interrupt (optional).
- Write the key sequence to NVMKEY.
- Set the WR bit to begin the erase cycle.
- Either poll the WR bit or wait for the NVM
interrupt (NVMIF is set).
- To get cleared, wait until NVMIF is set.
A typical single-word write sequence is provided in
Example 6-4.
EXAMPLE 6-3:
DATA EEPROM BULK ERASE
// Set up NVMCON to bulk erase the data EEPROM
NVMCON = 0x4050;
// Disable Interrupts For 5 Instructions
asm volatile ("disi #5");
// Issue Unlock Sequence and Start Erase Cycle
__builtin_write_NVM();
EXAMPLE 6-4:
SINGLE-WORD WRITE TO DATA EEPROM
int __attribute__ ((space(eedata))) eeData = 0x1234;
int newData;
// New data to write to EEPROM
/*--------------------------------------------------------------------------------------------The variable eeData must be a Global variable declared outside of any method
the code following this comment can be written inside the method that will execute the write
----------------------------------------------------------------------------------------------*/
unsigned int offset;
// Set up NVMCON to erase one word of data EEPROM
NVMCON = 0x4004;
// Set up a pointer to the EEPROM location to be erased
TBLPAG = __builtin_tblpage(&eeData);
// Initialize EE Data page pointer
offset = __builtin_tbloffset(&eeData);
// Initizlize lower word of address
__builtin_tblwtl(offset, newData);
// Write EEPROM data to write latch
asm volatile ("disi #5");
__builtin_write_NVM();
while(NVMCONbits.WR=1);
 2013 Microchip Technology Inc.
//
//
//
//
Disable Interrupts For 5 Instructions
Issue Unlock Sequence & Start Write Cycle
Optional: Poll WR bit to wait for
write sequence to complete
Advance Information
DS33030A-page 77
PIC24FV16KM204 FAMILY
6.4.3
READING THE DATA EEPROM
To read a word from data EEPROM, the Table Read
instruction is used. Since the EEPROM array is only
16 bits wide, only the TBLRDL instruction is needed.
The read operation is performed by loading TBLPAG
and WREG with the address of the EEPROM location,
followed by a TBLRDL instruction.
EXAMPLE 6-5:
A typical read sequence, using the Table
Pointer management (builtin_tblpage and
builtin_tbloffset)
and
Table
Read
(builtin_tblrdl) procedures from the C30
compiler library, is provided in Example 6-5.
Program Space Visibility (PSV) can also be used to
read locations in the data EEPROM.
READING THE DATA EEPROM USING THE TBLRD COMMAND
int __attribute__ ((space(eedata))) eeData = 0x1234;
int data;
// Data read from EEPROM
/*-------------------------------------------------------------------------------------------The variable eeData must be a Global variable declared outside of any method
the code following this comment can be written inside the method that will execute the read
---------------------------------------------------------------------------------------------*/
unsigned int offset;
// Set
TBLPAG
offset
data =
up a pointer to the EEPROM location to be erased
= __builtin_tblpage(&eeData);
// Initialize EE Data page pointer
= __builtin_tbloffset(&eeData);
// Initizlize lower word of address
__builtin_tblrdl(offset);
// Write EEPROM data to write latch
DS33030A-page 78
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
7.0
RESETS
Note:
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on
Resets, refer to the “PIC24F Family
Reference Manual”, Section 40. “Reset
with Programmable Brown-out Reset”
(DS39728).
The Reset module combines all Reset sources and
controls the device Master Reset Signal, SYSRST. The
following is a list of device Reset sources:
•
•
•
•
•
•
•
•
•
POR: Power-on Reset
MCLR: Pin Reset
SWR: RESET Instruction
WDTR: Watchdog Timer Reset
BOR: Brown-out Reset
LPBOR: Low-Power BOR
TRAPR: Trap Conflict Reset
IOPUWR: Illegal Opcode Reset
UWR: Uninitialized W Register Reset
Any active source of Reset will make the SYSRST
signal active. Many registers associated with the CPU
and peripherals are forced to a known Reset state.
Most registers are unaffected by a Reset; their status is
unknown on Power-on Reset (POR) and unchanged by
all other Resets.
Note:
All types of device Reset will set a corresponding status
bit in the RCON register to indicate the type of Reset
(see Register 7-1). A Power-on Reset will clear all bits
except for the BOR and POR bits (RCON<1:0>) which
are set. The user may set or clear any bit at any time
during code execution. The RCON bits only serve as
status bits. Setting a particular Reset status bit in
software will not cause a device Reset to occur.
The RCON register also has other bits associated with
the Watchdog Timer (WDT) and device power-saving
states. The function of these bits is discussed in other
sections of this manual.
A simplified block diagram of the Reset module is
shown in Figure 7-1.
FIGURE 7-1:
Refer to the specific peripheral or
Section 3.0 “CPU” of this data sheet for
register Reset states.
Note:
The status bits in the RCON register
should be cleared after they are read so
that the next RCON register value after a
device Reset will be meaningful.
RESET SYSTEM BLOCK DIAGRAM
RESET
Instruction
Glitch Filter
MCLR
WDT
Module
Sleep or Idle
BOREN<1:0>
0
SBOREN
(RCON<13>)
SLEEP
00
1
11
01
10
VDD Rise
Detect
POR
Brown-out
Reset
BOR
SYSRST
VDD
Enable Voltage Regulator
PIC24FV16KMXXX (only)
Configuration Mismatch
Trap Conflict
Illegal Opcode
Uninitialized W Register
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 79
PIC24FV16KM204 FAMILY
RCON: RESET CONTROL REGISTER(1)
REGISTER 7-1:
R/W-0, HS
R/W-0, HS
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
TRAPR
IOPUWR
SBOREN
RETEN(3)
—
—
CM
PMSLP
bit 15
bit 8
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-1, HS
R/W-1, HS
EXTR
SWR
SWDTEN(2)
WDTO
SLEEP
IDLE
BOR
POR
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
bit 14
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or Uninitialized W register used as an Address
Pointer caused a Reset
0 = An illegal opcode or Uninitialized W Reset has not occurred
bit 13
SBOREN: Software Enable/Disable of BOR bit
1 = BOR is turned on in software
0 = BOR is turned off in software
bit 12
RETEN: Retention Sleep Mode(3)
1 = Regulated voltage supply provided by the Retention Regulator (RETREG) during Sleep
0 = Regulated voltage supply provided by the main Voltage Regulator (VREG) during Sleep
bit 11-10
Unimplemented: Read as ‘0’
bit 9
CM: Configuration Word Mismatch Reset Flag bit
1 = A Configuration Word Mismatch Reset has occurred
0 = A Configuration Word Mismatch Reset has not occurred
bit 8
PMSLP: Program Memory Power During Sleep bit
1 = Program memory bias voltage remains powered during Sleep
0 = Program memory bias voltage is powered down during Sleep and the voltage regulator enters
Standby mode
bit 7
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
bit 6
SWR: Software RESET (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
bit 5
SWDTEN: Software Enable/Disable of WDT bit(2)
1 = WDT is enabled
0 = WDT is disabled
Note 1:
2:
3:
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTENx Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled regardless of the
SWDTEN bit setting.
This is implemented on PIC24FV16KMXXX parts only; not used on PIC24F16KMXXX devices.
DS33030A-page 80
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
RCON: RESET CONTROL REGISTER(1) (CONTINUED)
REGISTER 7-1:
bit 4
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
bit 3
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
bit 2
IDLE: Wake-up from Idle Flag bit
1 = Device has been in Idle mode
0 = Device has not been in Idle mode
bit 1
BOR: Brown-out Reset Flag bit
1 = A Brown-out Reset has occurred (the BOR is also set after a POR)
0 = A Brown-out Reset has not occurred
bit 0
POR: Power-on Reset Flag bit
1 = A Power-up Reset has occurred
0 = A Power-up Reset has not occurred
Note 1:
2:
3:
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTENx Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled regardless of the
SWDTEN bit setting.
This is implemented on PIC24FV16KMXXX parts only; not used on PIC24F16KMXXX devices.
TABLE 7-1:
RESET FLAG BIT OPERATION
Flag Bit
Setting Event
Clearing Event
TRAPR (RCON<15>)
Trap Conflict Event
POR
IOPUWR (RCON<14>)
Illegal Opcode or Uninitialized W Register Access
POR
CM (RCON<9>)
Configuration Mismatch Reset
POR
EXTR (RCON<7>)
MCLR Reset
POR
SWR (RCON<6>)
RESET Instruction
WDTO (RCON<4>)
WDT Time-out
SLEEP (RCON<3>)
PWRSAV #SLEEP Instruction
POR
IDLE (RCON<2>)
PWRSAV #IDLE Instruction
POR
POR
PWRSAV Instruction, POR
BOR (RCON<1>)
POR, BOR
—
POR (RCON<0>)
POR
—
Note:
All Reset flag bits may be set or cleared by the user software.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 81
PIC24FV16KM204 FAMILY
7.1
Clock Source Selection at Reset
If clock switching is enabled, the system clock source at
device Reset is chosen, as shown in Table 7-2. If clock
switching is disabled, the system clock source is always
selected according to the Oscillator Configuration bits.
For more information, see Section 9.0 “Oscillator
Configuration”.
TABLE 7-2:
OSCILLATOR SELECTION vs.
TYPE OF RESET (CLOCK
SWITCHING ENABLED)
Reset Type
POR
Clock Source Determinant
FNOSCx Configuration bits
(FNOSC<10:8>)
BOR
MCLR
7.2
Device Reset Times
The Reset times for various types of device Reset are
summarized in Table 7-3. Note that the system Reset
signal, SYSRST, is released after the POR and PWRT
delay times expire.
The time at which the device actually begins to execute
code will also depend on the system oscillator delays,
which include the Oscillator Start-up Timer (OST) and
the PLL lock time. The OST and PLL lock times occur
in parallel with the applicable SYSRST delay times.
The FSCM delay determines the time at which the
FSCM begins to monitor the system clock source after
the SYSRST signal is released.
COSCx Control bits
(OSCCON<14:12>)
WDTO
SWR
TABLE 7-3:
RESET DELAY TIMES FOR VARIOUS DEVICE RESETS
Reset Type
POR(6)
BOR
Clock Source
System Clock
Delay
Notes
EC
TPOR + TPWRT
—
FRC, FRCDIV
TPOR + TPWRT
TFRC
1, 2, 3
LPRC
TPOR + TPWRT
TLPRC
1, 2, 3
ECPLL
TPOR + TPWRT
TLOCK
1, 2, 4
FRCPLL
TPOR + TPWRT
TFRC + TLOCK
XT, HS, SOSC
TPOR+ TPWRT
TOST
XTPLL, HSPLL
TPOR + TPWRT
TOST + TLOCK
TPWRT
—
EC
All Others
SYSRST Delay
1, 2
1, 2, 3, 4
1, 2, 5
1, 2, 4, 5
2
FRC, FRCDIV
TPWRT
TFRC
2, 3
LPRC
TPWRT
TLPRC
2, 3
2, 4
ECPLL
TPWRT
TLOCK
FRCPLL
TPWRT
TFRC + TLOCK
2, 3, 4
XT, HS, SOSC
TPWRT
TOST
XTPLL, HSPLL
TPWRT
TFRC + TLOCK
2, 3, 4
—
—
None
Any Clock
2, 5
Note 1:
2:
3:
4:
5:
TPOR = Power-on Reset delay.
TPWRT = 64 ms nominal if the Power-up Timer is enabled; otherwise, it is zero.
TFRC and TLPRC = RC oscillator start-up times.
TLOCK = PLL lock time.
TOST = Oscillator Start-up Timer (OST). A 10-bit counter waits 1024 oscillator periods before releasing the
oscillator clock to the system.
6: If Two-Speed Start-up is enabled, regardless of the primary oscillator selected, the device starts with FRC,
and in such cases, FRC start-up time is valid.
Note:
For detailed operating frequency and timing specifications, see Section 29.0 “Electrical Characteristics”.
DS33030A-page 82
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
7.2.1
POR AND LONG OSCILLATOR
START-UP TIMES
The oscillator start-up circuitry and its associated delay
timers are not linked to the device Reset delays that
occur at power-up. Some crystal circuits (especially
low-frequency crystals) will have a relatively long
start-up time. Therefore, one or more of the following
conditions is possible after SYSRST is released:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer (OST) has not
expired (if a crystal oscillator is used).
• The PLL has not achieved a lock (if PLL is used).
The device will not begin to execute code until a valid
clock source has been released to the system.
Therefore, the oscillator and PLL start-up delays must
be considered when the Reset delay time must be
known.
7.2.2
FAIL-SAFE CLOCK MONITOR
(FSCM) AND DEVICE RESETS
If the FSCM is enabled, it will begin to monitor the
system clock source when SYSRST is released. If a
valid clock source is not available at this time, the
device will automatically switch to the FRC oscillator
and the user can switch to the desired crystal oscillator
in the Trap Service Routine (TSR).
7.3
Special Function Register Reset
States
Most of the Special Function Registers (SFRs)
associated with the PIC24F CPU and peripherals are
reset to a particular value at a device Reset. The SFRs
are grouped by their peripheral or CPU function and their
Reset values are specified in each section of this manual.
The Reset value for each SFR does not depend on the
type of Reset, with the exception of four registers. The
Reset value for the Reset Control register, RCON, will
depend on the type of device Reset. The Reset value for
the Oscillator Control register, OSCCON, will depend on
the type of Reset and the programmed values of the
FNOSCx bits in the Flash Configuration Word
(FOSCSEL<2:0>); see Table 7-2. The RCFGCAL and
NVMCON registers are only affected by a POR.
 2013 Microchip Technology Inc.
7.4
Brown-out Reset (BOR)
The PIC24FV16KM204 family devices implement a
BOR circuit, which provides the user several
configuration and power-saving options. The BOR is
controlled by the BORV<1:0> and BOREN<1:0>
Configuration bits (FPOR<6:5,1:0>). There are a total
of four BOR configurations, which are provided in
Table 7-3.
The BOR threshold is set by the BORV<1:0> bits. If
BOR is enabled (any values of BOREN<1:0>, except
‘00’), any drop of VDD below the set threshold point will
reset the device. The chip will remain in BOR until VDD
rises above the threshold.
If the Power-up Timer is enabled, it will be invoked after
VDD rises above the threshold. Then, it will keep the chip
in Reset for an additional time delay, TPWRT, if VDD
drops below the threshold while the Power-up Timer is
running. The chip goes back into a BOR and the
Power-up Timer will be initialized. Once VDD rises above
the threshold, the Power-up Timer will execute the
additional time delay.
BOR and the Power-up Timer (PWRT) are independently configured. Enabling the Brown-out Reset does
not automatically enable the PWRT.
7.4.1
LOW-POWER BOR (LPBOR)
The Low-Power BOR is an alternate setting for the BOR,
designed to consume minimal power. In LPBOR mode,
BORV (FPOR<6:5>) = 00. The BOR trip point is approximately 2.0V. Due to the low-current consumption, the
accuracy of the LPBOR mode can vary.
Unlike the other BOR modes, LPBOR mode will not
cause a device Reset when VDD drops below the trip
point. Instead, it re-arms the POR circuit to ensure that
the device will reset properly in the event that VDD
continues to drop below the minimum operating voltage.
The device will continue to execute code when VDD is
below the level of the LPBOR trip point. A device that
requires falling edge BOR protection to prevent code
from improperly executing should use one of the other
BOR voltage settings.
Advance Information
DS33030A-page 83
PIC24FV16KM204 FAMILY
7.4.2
SOFTWARE ENABLED BOR
When BOREN<1:0> = 01, the BOR can be enabled or
disabled by the user in software. This is done with the
control bit, SBOREN (RCON<13>). Setting SBOREN
enables the BOR to function as previously described.
Clearing the SBOREN disables the BOR entirely. The
SBOREN bit operates only in this mode; otherwise, it is
read as ‘0’.
Placing BOR under software control gives the user the
additional flexibility of tailoring the application to its
environment without having to reprogram the device to
change the BOR configuration. It also allows the user to
tailor the incremental current that the BOR consumes.
While the BOR current is typically very small, it may have
some impact in low-power applications.
Note:
7.4.3
7.4.4
DISABLING BOR IN SLEEP MODE
When BOREN<1:0> = 10, BOR remains under hardware
control and operates as previously described. However,
whenever the device enters Sleep mode, BOR is
automatically disabled. When the device returns to any
other operating mode, BOR is automatically re-enabled.
This mode allows for applications to recover from
brown-out situations, while actively executing code,
when the device requires BOR protection the most. At
the same time, it saves additional power in Sleep mode
by eliminating the small incremental BOR current.
Note:
Even when the BOR is under software control, the Brown-out Reset voltage level is
still set by the BORV<1:0> Configuration
bits; it can not be changed in software.
BOR levels differ depending on device type;
PIC24FV16KM204 devices are at different
levels than those of PIC24F16KM204
devices. See Section 27.0 “Electrical
Characteristics” for BOR voltage levels.
DETECTING BOR
When BOR is enabled, the BOR bit (RCON<1>) is
always reset to ‘1’ on any BOR or POR event. This
makes it difficult to determine if a BOR event has
occurred just by reading the state of BOR alone. A
more reliable method is to simultaneously check the
state of both POR and BOR. This assumes that the
POR and BOR bits are reset to ‘0’ in the software
immediately after any POR event. If the BOR bit is ‘1’
while POR is ‘0’, it can be reliably assumed that a BOR
event has occurred.
DS33030A-page 84
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
8.0
Note:
INTERRUPT CONTROLLER
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on the
Interrupt Controller, refer to the “PIC24F
Family Reference Manual”, Section 8.
“Interrupts” (DS39707).
The PIC24F interrupt controller reduces the numerous
peripheral interrupt request signals to a single interrupt
request signal to the CPU. It has the following features:
• Up to Eight Processor Exceptions and
Software Traps
• Seven User-Selectable Priority Levels
• Interrupt Vector Table (IVT) with up to 118 Vectors
• Unique Vector for Each Interrupt or Exception
Source
• Fixed Priority within a Specified User Priority
Level
• Alternate Interrupt Vector Table (AIVT) for Debug
Support
• Fixed Interrupt Entry and Return Latencies
8.1
Interrupt Vector Table (IVT)
The IVT is shown in Figure 8-1. The IVT resides in the
program memory, starting at location, 000004h. The IVT
contains 126 vectors, consisting of eight non-maskable
trap vectors, plus, up to 118 sources of interrupt. In general, each interrupt source has its own vector. Each interrupt vector contains a 24-bit-wide address. The value
programmed into each interrupt vector location is the
starting address of the associated Interrupt Service Routine (ISR).
8.1.1
ALTERNATE INTERRUPT VECTOR
TABLE (AIVT)
The Alternate Interrupt Vector Table (AIVT) is located
after the IVT, as shown in Figure 8-1. Access to the
AIVT is provided by the ALTIVT control bit
(INTCON2<15>). If the ALTIVT bit is set, all interrupt
and exception processes will use the alternate vectors
instead of the default vectors. The alternate vectors are
organized in the same manner as the default vectors.
The AIVT supports emulation and debugging efforts by
providing a means to switch between an application
and a support environment without requiring the interrupt vectors to be reprogrammed. This feature also
enables switching between applications for evaluation
of different software algorithms at run-time. If the AIVT
is not needed, the AIVT should be programmed with
the same addresses used in the IVT.
8.2
Reset Sequence
A device Reset is not a true exception, because the
interrupt controller is not involved in the Reset process.
The PIC24F devices clear their registers in response to
a Reset, which forces the Program Counter (PC) to
zero. The microcontroller then begins program
execution at location, 000000h. The user programs a
GOTO instruction at the Reset address, which redirects
the program execution to the appropriate start-up
routine.
Note:
Any unimplemented or unused vector
locations in the IVT and AIVT should be
programmed with the address of a default
interrupt handler routine that contains a
RESET instruction.
Interrupt vectors are prioritized in terms of their natural
priority; this is linked to their position in the vector table.
All other things being equal, lower addresses have a
higher natural priority. For example, the interrupt
associated with Vector 0 will take priority over interrupts
at any other vector address.
PIC24FV16KM204 family devices implement
non-maskable traps and unique interrupts; these are
summarized in Table 8-1.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 85
PIC24FV16KM204 FAMILY
Decreasing Natural Order Priority
FIGURE 8-1:
DS33030A-page 86
PIC24F INTERRUPT VECTOR TABLE
Reset – GOTO Instruction
Reset – GOTO Address
Reserved
Oscillator Fail Trap Vector
Address Error Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
Reserved
Reserved
Reserved
Interrupt Vector 0
Interrupt Vector 1
—
—
—
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
—
—
—
Interrupt Vector 116
Interrupt Vector 117
Reserved
Reserved
Reserved
Oscillator Fail Trap Vector
Address Error Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
Reserved
Reserved
Reserved
Interrupt Vector 0
Interrupt Vector 1
—
—
—
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
—
—
—
Interrupt Vector 116
Interrupt Vector 117
Start of Code
000000h
000002h
000004h
000014h
00007Ch
00007Eh
000080h
Interrupt Vector Table (IVT)
0000FCh
0000FEh
000100h
000102h
000114h
Alternate Interrupt Vector Table (AIVT)
00017Ch
00017Eh
000180h
0001FEh
000200h
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 8-1:
TRAP VECTOR DETAILS
Vector Number
IVT Address
AIVT Address
Trap Source
0
000004h
000104h
Reserved
1
000006h
000106h
Oscillator Failure
2
000008h
000108h
Address Error
3
00000Ah
00010Ah
Stack Error
4
00000Ch
00010Ch
Math Error
5
00000Eh
00010Eh
Reserved
6
000010h
000110h
Reserved
7
000012h
000112h
Reserved
TABLE 8-2:
IMPLEMENTED INTERRUPT VECTORS
Interrupt Source
Vector Number IVT Address
AIVT
Address
Interrupt Bit Locations
Flag
Enable
Priority
ADC1 – ADC1 Convert Done
13
00002Eh
00012Eh
IFS0<13>
IEC0<13>
IPC3<6:4>
CLC1
96
0000D4h
0001D4h
IFS6<0>
IEC6<0>
IPC24<2:0>
CLC2
97
0000D6h
0001D6h
IFS6<1>
IEC6<1>
IPC24<6:4>
Comparator Interrupt
18
000038h
000138h
IFS1<2>
IEC1<2>
IPC4<10:8>
CTMU
77
0000AEh
0001AEh
IFS4<13>
IEC4<13>
IPC19<6:4>
DAC1 – Buffer Update
78
0000B0h
0001B0h
IFS4<14>
IEC4<14>
IPC19<10:8>
IPC19<14:12>
DAC2 – Buffer Update
79
0000B2h
0001B2h
IFS4<15>
IEC4<15>
HLVD – High/Low-Voltage Detect
72
0000A4h
0001A4h
IFS4<8>
IEC4<8>
IPC18<2:0>
ICN – Input Change Notification
19
00003Ah
00013Ah
IFS1<3>
IEC1<3>
IPC4<14:12>
INT0 – External Interrupt 0
0
000014h
000114h
IFS0<0>
IEC0<0>
IPC0<2:0>
INT1 – External Interrupt 1
20
00003Ch
00013Ch
IFS1<4>
IEC1<4>
IPC5<2:0>
INT2 – External Interrupt 2
29
00004Eh
00014Eh
IFS1<13>
IEC1<13>
IPC7<6:4>
MCCP1 – Capture/Compare
1
000016h
000116h
IFS0<1>
IEC0<1>
IPC0<6:4>
MCCP1 – Time Base
7
000022h
000122h
IFS0<7>
IEC0<7>
IPC1<14:12>
MCCP2 – Capture/Compare
2
000018h
000118h
IFS0<2>
IEC0<2>
IPC0<10:8>
MCCP2 – Time Base
8
000024h
000124h
IFS0<8>
IEC0<8>
IPC2<2:0>
MCCP3 – Capture/Compare
5
00001Eh
00011Eh
IFS0<5>
IEC0<5>
IPC1<6:4>
MCCP3 – Time Base
27
00004Ah
00014Ah
IFS1<11>
IEC1<11>
IPC6<14:12>
MSSP1 – Bus Collision Interrupt
17
000036h
000136h
IFS1<1>
IEC1<1>
IPC4<6:4>
MSSP1 – I2C/SPI Interrupt
16
000034h
000134h
IFS1<0>
IEC1<0>
IPC4<2:0>
MSSP2 – Bus Collision Interrupt
50
000078h
000178h
IFS3<2>
IEC3<2>
IPC12<10:8>
MSSP2 – I2C™/SPI Interrupt
49
000076h
000176h
IFS3<1>
IEC3<1>
IPC12<6:4>
NVM – NVM Write Complete
15
000032h
000132h
IFS0<15>
IEC0<15>
IPC3<14:12>
RTCC – Real-Time Clock/Calendar
62
000090h
000190h
IFS3<14>
IEC3<14>
IPC15<10:8>
SCCP4 – Capture/Compare
6
000020h
000120h
IFS0<6>
IEC0<6>
IPC1<10:8>
SCCP4 – Time Base
28
00004Ch
00014Ch
IFS1<12>
IEC1<12>
IPC7<2:0>
SCCP5 – Capture/Compare
22
000040h
000140h
IFS1<6>
IEC1<6>
IPC5<10:8>
SCCP5 – Time Base
41
000066h
000166h
IFS2<9>
IEC2<9>
IPC10<6:4>
TMR1 – Timer1
3
00001Ah
00011Ah
IFS0<3>
IEC0<3>
IPC0<14:12>
UART1 Error
65
000096h
000196h
IFS4<1>
IEC4<1>
IPC16<6:4>
UART2 Error
66
000098h
000198h
IFS4<2>
IEC4<2>
IPC16<10:8>
IPC2<14:12>
UART1RX – UART1 Receiver
11
00002Ah
00012Ah
IFS0<11>
IEC0<11>
UART1TX – UART1 Transmitter
12
00002Ch
00012Ch
IFS0<12>
IEC0<12>
IPC3<2:0>
UART2RX – UART2 Receiver
30
000050h
000150h
IFS1<14>
IEC1<14>
IPC7<10:8>
UART2TX – UART2 Transmitter
31
000052h
000152h
IFS1<15>
IEC1<15>
IPC7<14:12>
ULPWU – Ultra Low-Power Wake-up
80
0000B4h
0001B4h
IFS5<0>
IEC5<0>
IPC20<2:0>
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 87
PIC24FV16KM204 FAMILY
8.3
Interrupt Control and Status
Registers
The PIC24FV16KM204 family of devices implements a
total of 33 registers for the interrupt controller:
•
•
•
•
•
INTCON1
INTCON2
IFS0 through IFS6
IEC0 through IEC6
IPC0 through IPC7, IPC10, IPC12, IPC15, IPC16,
IPC18 through IPC20 and IPC24
• INTTREG
Global Interrupt Enable (GIE) control functions are
controlled from INTCON1 and INTCON2. INTCON1
contains the Interrupt Nesting Disable (NSTDIS) bit, as
well as the control and status flags for the processor
trap sources. The INTCON2 register controls the external interrupt request signal behavior and the use of the
AIV table.
The IFSx registers maintain all of the interrupt request
flags. Each source of interrupt has a status bit, which is
set by the respective peripherals, or external signal,
and is cleared via software.
The IECx registers maintain all of the interrupt enable
bits. These control bits are used to individually enable
interrupts from the peripherals or external signals.
The IPCx registers are used to set the Interrupt Priority
Level (IPL) for each source of interrupt. Each user
interrupt source can be assigned to one of eight priority
levels.
DS33030A-page 88
The INTTREG register contains the associated
interrupt vector number and the new CPU Interrupt
Priority Level, which are latched into the Vector
Number (VECNUM<6:0>) and the Interrupt Level
(ILR<3:0>) bit fields in the INTTREG register. The new
Interrupt Priority Level is the priority of the pending
interrupt.
The interrupt sources are assigned to the IFSx, IECx
and IPCx registers in the same sequence. For
example, the INT0 (External Interrupt 0) is depicted as
having a vector number and a natural order priority of
0. The INT0IF status bit is found in IFS0<0>, the INT0IE
enable bit in IEC0<0> and the INT0IP<2:0> priority bits
are in the first position of IPC0 (IPC0<2:0>).
Although they are not specifically part of the interrupt
control hardware, two of the CPU Control registers contain bits that control interrupt functionality. The ALU
STATUS Register (SR) contains the IPL<2:0> bits
(SR<7:5>). These indicate the current CPU Interrupt
Priority Level. The user may change the current CPU
Interrupt Priority Level by writing to the IPLx bits.
The CORCON register contains the IPL3 bit, which
together with IPL<2:0>, also indicates the current CPU
Interrupt Priority Level. IPL3 is a read-only bit so that the
trap events cannot be masked by the user’s software.
All Interrupt registers are described in Register 8-1
through Register 8-35, in the following sections.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-1:
SR: ALU STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R-0, HSC
—
—
—
—
—
—
—
DC(1)
bit 15
bit 8
R/W-0, HSC
R/W-0, HSC
R/W-0, HSC
R-0, HSC
R/W-0, HSC
R/W-0, HSC
R/W-0, HSC
R/W-0, HSC
IPL2(2,3)
IPL1(2,3)
IPL0(2,3)
RA(1)
N(1)
OV(1)
Z(1)
C(1)
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-9
Unimplemented: Read as ‘0’
bit 7-5
IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3)
111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled
110 = CPU Interrupt Priority Level is 6 (14)
101 = CPU Interrupt Priority Level is 5 (13)
100 = CPU Interrupt Priority Level is 4 (12)
011 = CPU Interrupt Priority Level is 3 (11)
010 = CPU Interrupt Priority Level is 2 (10)
001 = CPU Interrupt Priority Level is 1 (9)
000 = CPU Interrupt Priority Level is 0 (8)
Note 1:
2:
3:
Note:
x = Bit is unknown
See Register 3-1 for the description of these bits, which are not dedicated to interrupt control functions.
The IPL<2:0> bits are concatenated with the IPL3 bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the Interrupt Priority Level if IPL3 = 1.
The IPLx Status bits are read-only when NSTDIS (INTCON1<15>) = 1.
Bit 8 and bits 4 through 0 are described in Section 3.0 “CPU”.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 89
PIC24FV16KM204 FAMILY
REGISTER 8-2:
CORCON: CPU CONTROL REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R/C-0, HSC
R/W-0
U-0
U-0
—
—
—
—
IPL3(2)
PSV(1)
—
—
bit 7
bit 0
Legend:
C = Clearable bit
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3
IPL3: CPU Interrupt Priority Level Status bit(2)
1 = CPU Interrupt Priority Level is greater than 7
0 = CPU Interrupt Priority Level is 7 or less
bit 1-0
Unimplemented: Read as ‘0’
Note 1:
2:
Note:
x = Bit is unknown
See Register 3-2 for the description of this bit, which is not dedicated to interrupt control functions.
The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.
Bit 2 is described in Section 3.0 “CPU”.
DS33030A-page 90
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-3:
INTCON1: INTERRUPT CONTROL REGISTER 1
R/W-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
NSTDIS
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
U-0
—
—
—
MATHERR
ADDRERR
STKERR
OSCFAIL
—
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
NSTDIS: Interrupt Nesting Disable bit
1 = Interrupt nesting is disabled
0 = Interrupt nesting is enabled
bit 14-5
Unimplemented: Read as ‘0’
bit 4
MATHERR: Arithmetic Error Trap Status bit
1 = Overflow trap has occurred
0 = Overflow trap has not occurred
bit 3
ADDRERR: Address Error Trap Status bit
1 = Address error trap has occurred
0 = Address error trap has not occurred
bit 2
STKERR: Stack Error Trap Status bit
1 = Stack error trap has occurred
0 = Stack error trap has not occurred
bit 1
OSCFAIL: Oscillator Failure Trap Status bit
1 = Oscillator failure trap has occurred
0 = Oscillator failure trap has not occurred
bit 0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 91
PIC24FV16KM204 FAMILY
REGISTER 8-4:
INTCON2: INTERRUPT CONTROL REGISTER 2
R/W-0
R-0, HSC
U-0
U-0
U-0
U-0
U-0
U-0
ALTIVT
DISI
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
—
—
—
—
—
INT2EP
INT1EP
INT0EP
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
ALTIVT: Enable Alternate Interrupt Vector Table bit
1 = Uses Alternate Interrupt Vector Table (AIVT)
0 = Uses standard (default) Interrupt Vector Table (IVT)
bit 14
DISI: DISI Instruction Status bit
1 = DISI instruction is active
0 = DISI instruction is not active
bit 13-3
Unimplemented: Read as ‘0’
bit 2
INT2EP: External Interrupt 2 Edge Detect Polarity Select bit
1 = Interrupt is on the negative edge
0 = Interrupt is on the positive edge
bit 1
INT1EP: External Interrupt 1 Edge Detect Polarity Select bit
1 = Interrupt is on the negative edge
0 = Interrupt is on the positive edge
bit 0
INT0EP: External Interrupt 0 Edge Detect Polarity Select bit
1 = Interrupt is on the negative edge
0 = Interrupt is on the positive edge
DS33030A-page 92
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-5:
IFS0: INTERRUPT FLAG STATUS REGISTER 0
R/W-0, HS
NVMIF
bit 15
U-0
—
R/W-0, HS
AD1IF
R/W-0, HS
U1TXIF
R/W-0, HS
U1RXIF
U-0
—
U-0
—
R/W-0, HS
CCT2IF
bit 8
R/W-0, HS
CCT1IF
bit 7
R/W-0, HS
CCP4IF
R/W-0, HS
CCP3IF
U-0
—
R/W-0, HS
T1IF
R/W-0, HS
CCP2IF
R/W-0, HS
CCP1IF
R/W-0, HS
INT0IF
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10-9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
HS = Hardware Settable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
NVMIF: NVM Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
Unimplemented: Read as ‘0’
AD1IF: A/D Conversion Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
U1TXIF: UART1 Transmitter Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
U1RXIF: UART1 Receiver Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
Unimplemented: Read as ‘0’
CCT2IF: Capture Compare 2 Timer Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
CCT1IF: Capture Compare 1 Timer Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
CCP4IF: Capture Compare 4 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
CCP3IF: Capture Compare 3 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
Unimplemented: Read as ‘0’
T1IF: Timer1 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
CCP2IF: Capture Compare 2 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
CCP1IF: Capture Compare 1 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
INT0IF: External Interrupt 0 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 93
PIC24FV16KM204 FAMILY
REGISTER 8-6:
IFS1: INTERRUPT FLAG STATUS REGISTER 1
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
U-0
U-0
U-0
U2TXIF
U2RXIF
INT2IF
CCT4IF
CCT3IF
—
—
—
bit 15
bit 8
U-0
R/W-0, HS
U-0
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
R/W-0, HS
—
CCP5IF
—
INT1IF
CNIF
CMIF
BCL1IF
SSP1IF
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
U2TXIF: UART2 Transmitter Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 14
U2RXIF: UART2 Receiver Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 13
INT2IF: External Interrupt 2 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 12
CCT4IF: Capture Compare 4 Timer Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 11
CCT3IF: Capture Compare 3 Timer Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 10-7
Unimplemented: Read as ‘0’
bit 6
CCP5IF: Capture Compare 5 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 5
Unimplemented: Read as ‘0’
bit 4
INT1IF: External Interrupt 1 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 3
CNIF: Input Change Notification Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 2
CMIF: Comparator Interrupt Flag Status Bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
BCL1IF: MSSP1 I2C™ Bus Collision Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
SI2C1IF: MSSP1 SPI/I2C Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
DS33030A-page 94
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-7:
IFS2: INTERRUPT FLAG STATUS REGISTER 2
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0, HS
U-0
—
—
—
—
—
—
CCT5IF
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-10
Unimplemented: Read as ‘0’
bit 9
CCT5IF: Capture Compare 5 Timer Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 8-0
Unimplemented: Read as ‘0’
REGISTER 8-8:
x = Bit is unknown
IFS3: INTERRUPT FLAG STATUS REGISTER 3
U-0
R/W-0, HS
U-0
U-0
U-0
U-0
U-0
U-0
—
RTCIF
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0, HS
R/W-0, HS
U-0
—
—
—
—
—
BCL2IF
SSP2IF
—
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14
RTCIF: Real-Time Clock and Calendar Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 13-3
Unimplemented: Read as ‘0’
bit 2
BCL2IF: MSSP2 I2C™ Bus Collision Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
SSP2IF: MSSP2 SPI/I2C Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 95
PIC24FV16KM204 FAMILY
REGISTER 8-9:
IFS4: INTERRUPT FLAG STATUS REGISTER 4
R/W-0, HS
R/W-0, HS
R/W-0, HS
U-0
U-0
U-0
U-0
R/W-0, HS
DAC2IF
DAC1IF
CTMUIF
—
—
—
—
HLVDIF
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0, HS
R/W-0, HS
U-0
—
—
—
—
—
U2ERIF
U1ERIF
—
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
DAC2IF: Digital-to-Analog Converter 2 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 14
DAC1IF: Digital-to-Analog Converter 1 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 13
CTMUIF: CTMU Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 12-9
Unimplemented: Read as ‘0’
bit 8
HLVDIF: High/Low-Voltage Detect Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 7-3
Unimplemented: Read as ‘0’
bit 2
U2ERIF: UART2 Error Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
U1ERIF: UART1 Error Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
Unimplemented: Read as ‘0’
DS33030A-page 96
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-10:
IFS5: INTERRUPT FLAG STATUS REGISTER 5
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0, HS
—
—
—
—
—
—
—
ULPWUIF
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-1
Unimplemented: Read as ‘0’
bit 0
ULPWUIF: Ultra Low-Power Wake-up Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
REGISTER 8-11:
x = Bit is unknown
IFS6: INTERRUPT FLAG STATUS REGISTER 6
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0, HS
R/W-0, HS
—
—
—
—
—
—
CLC2IF
CLC1IF
bit 7
bit 0
Legend:
HS = Hardware Settable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-2
Unimplemented: Read as ‘0’
bit 1
CLC2IF: Configurable Logic Cell 2 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
CLC1IF: Configurable Logic Cell 1 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 97
PIC24FV16KM204 FAMILY
REGISTER 8-12:
IEC0: INTERRUPT ENABLE CONTROL REGISTER 0
R/W-0
NVMIE
bit 15
U-0
—
R/W-0
AD1IE
R/W-0
U1TXIE
R/W-0
U1RXIE
U-0
—
U-0
—
R/W-0
CCT2IE
bit 8
R/W-0
CCT1IE
bit 7
R/W-0
CCP4IE
R/W-0
CCP3IE
U-0
—
R/W-0
T1IE
R/W-0
CCP2IE
R/W-0
CCP1IE
R/W-0
INT0IE
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10-9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
NVMIE: NVM Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
Unimplemented: Read as ‘0’
AD1IE: A/D Conversion Complete Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
U1TXIE: UART1 Transmitter Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
U1RXIE: UART1 Receiver Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
Unimplemented: Read as ‘0’
CCT2IE: Capture Compare 2 Timer Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
CCT1IE: Capture Compare 1 Timer Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
CCP4IE: Capture Compare 4 Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
CCP3IE: Capture Compare 3 Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
Unimplemented: Read as ‘0’
T1IE: Timer1 Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
CCP2IE: Capture Compare 2 Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
CCP1IE: Capture Compare 1 Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
INT0IE: External Interrupt 0 Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
DS33030A-page 98
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-13:
IEC1: INTERRUPT ENABLE CONTROL REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U2TXIE
U2RXIE
INT2IE
CCT4IE
CCT3IE
—
—
—
bit 15
bit 8
U-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
CCP5IE
—
INT1IE
CNIE
CMIE
BCL1IE
SSP1IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
U2TXIE: UART2 Transmitter Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 14
U2RXIE: UART2 Receiver Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 13
INT2IE: External Interrupt 2 Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 12
CCT4IE: Capture Compare 4 Timer Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 11
CCT3IE: Capture Compare 3 Timer Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 10-7
Unimplemented: Read as ‘0’
bit 6
CCP5IE: Capture Compare 5 Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 5
Unimplemented: Read as ‘0’
bit 4
INT1IE: External Interrupt 1 Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 3
CNIE: Input Change Notification Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 2
CMIE: Comparator Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 1
BCL1IE: MSSP1 I2C™ Bus Collision Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 0
SSP1IE: MSSP1 SPI/I2C Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 99
PIC24FV16KM204 FAMILY
REGISTER 8-14:
IEC2: INTERRUPT ENABLE CONTROL REGISTER 2
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
U-0
—
—
—
—
—
—
CCT5IE
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-10
Unimplemented: Read as ‘0’
bit 9
CCT5IE: Capture Compare 5 Timer Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 8-0
Unimplemented: Read as ‘0’
REGISTER 8-15:
x = Bit is unknown
IEC3: INTERRUPT ENABLE CONTROL REGISTER 3
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
U-0
—
RTCIE
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
U-0
—
—
—
—
—
BCL2IE
SSP2IE
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14
RTCIE: Real-Time Clock and Calendar Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 13-3
Unimplemented: Read as ‘0’
bit 2
BCL2IE: MSSP2 I2C™ Bus Collision Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 1
SSP2IE: MSSP2 SPI/I2C Event Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 0
Unimplemented: Read as ‘0’
DS33030A-page 100
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-16:
IEC4: INTERRUPT ENABLE CONTROL REGISTER 4
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
R/W-0
DAC2IE
DAC1IE
CTMUIE
—
—
—
—
HLVDIE
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
U-0
—
—
—
—
—
U2ERIE
U1ERIE
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
DAC2IE: Digital-to-Analog Converter 2 Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 14
DAC1IE: Digital-to-Analog Converter 1 Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 13
CTMUIE: CTMU Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 12-9
Unimplemented: Read as ‘0’
bit 8
HLVDIE: High/Low-Voltage Detect Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 7-3
Unimplemented: Read as ‘0’
bit 2
U2ERIE: UART2 Error Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 1
U1ERIE: UART1 Error Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 101
PIC24FV16KM204 FAMILY
REGISTER 8-17:
IEC5: INTERRUPT ENABLE CONTROL REGISTER 5
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
ULPWUIE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-1
Unimplemented: Read as ‘0’
bit 0
ULPWUIE: Ultra Low-Power Wake-up Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
REGISTER 8-18:
x = Bit is unknown
IEC6: INTERRUPT ENABLE CONTROL REGISTER 5
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
—
—
—
—
—
—
CLC2IE
CLC2IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-2
Unimplemented: Read as ‘0’
bit 1
CLC2IE: Configurable Logic Cell 2 Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
bit 0
CLC1IE: Configurable Logic Cell 1 Interrupt Enable bit
1 = Interrupt request is enabled
0 = Interrupt request is not enabled
DS33030A-page 102
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-19:
IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
T1IP2
T1IP1
T1IP0
—
CCP2IP2
CCP2IP1
CCP2IP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
CCP1IP2
CCP1IP1
CCP1IP0
—
INT0IP2
INT0IP1
INT0IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
T1IP<2:0>: Timer1 Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
CCP2IP<2:0>: Capture Compare 2 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
CCP1IP<2:0>: Capture Compare 1 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
INT0IP<2:0>: External Interrupt 0 Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 103
PIC24FV16KM204 FAMILY
REGISTER 8-20:
IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
CCT1IP2
CCT1IP1
CCT1IP0
—
CCP4IP2
CCP4IP1
CCP4IP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
CCP3IP2
CCP3IP1
CCP3IP0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
CCT1IP<2:0>: Capture Compare 1 Timer Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
CCP4IP<2:0>: Capture Compare 4 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
CCP3IP<2:0>: Capture Compare 3 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS33030A-page 104
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-21:
IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
U1RXIP2
U1RXIP1
U1RXIP0
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
CCT2IP2
CCT2IP1
CCT2IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11-3
Unimplemented: Read as ‘0’
bit 2-0
CCT2IP<2:0>: Capture Compare 2 Timer Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 105
PIC24FV16KM204 FAMILY
REGISTER 8-22:
IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
NVMIP2
NVMIP1
NVMIP0
—
—
—
—
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
AD1IP2
AD1IP1
AD1IP0
—
U1TXIP2
U1TXIP1
U1TXIP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
NVMIP<2:0>: NVM Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11-7
Unimplemented: Read as ‘0’
bit 6-4
AD1IP<2:0>: A/D Conversion Complete Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
DS33030A-page 106
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-23:
IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
CNIP2
CNIP1
CNIP0
—
CMIP2
CMIP1
CMIP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
BCL1IP2
BCL1IP1
BCL1IP0
—
SSP1IP2
SSP1IP1
SSP1IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
CNIP<2:0>: Input Change Notification Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
CMIP<2:0>: Comparator Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
BCL1IP<2:0>: MSSP1 I2C™ Bus Collision Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
SSP1IP<2:0>: MSSP1 SPI/I2C Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 107
PIC24FV16KM204 FAMILY
REGISTER 8-24:
IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
CCP5IP2
CCP5IP1
CCP5IP0
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
INT1IP2
INT1IP1
INT1IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
CCP5IP<2:0>: Capture Compare 5 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7-3
Unimplemented: Read as ‘0’
bit 2-0
INT1IP<2:0>: External Interrupt 1 Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
DS33030A-page 108
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-25:
IPC6: INTERRUPT PRIORITY CONTROL REGISTER 6
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
CCT3IP2
CCT3IP1
CCT3IP0
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
CCT3IP<2:0>: Capture Compare 3 Timer Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11-0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 109
PIC24FV16KM204 FAMILY
REGISTER 8-26:
IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
U2TXIP2
U2TXIP1
U2TXIP0
—
U2RXIP2
U2RXIP1
U2RXIP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
INT2IP2
INT2IP1
INT2IP0
—
CCT4IP2
CCT4IP1
CCT4IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
U2TXIP<2:0>: UART2 Transmitter Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
U2RXIP<2:0>: UART2 Receiver Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
INT2IP<2:0>: External Interrupt 2 Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
CCT4IP<2:0>: Capture Compare 4 Timer Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
DS33030A-page 110
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-27:
IPC10: INTERRUPT PRIORITY CONTROL REGISTER 10
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
CCT5IP2
CCT5IP1
CCT5IP0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-7
Unimplemented: Read as ‘0’
bit 6-4
CCT5IP<2:0>: Capture Compare 5 Timer Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 111
PIC24FV16KM204 FAMILY
REGISTER 8-28:
IPC12: INTERRUPT PRIORITY CONTROL REGISTER 12
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
BCL2IP2
BCL2IP1
BCL2IP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
SSP2IP2
SSP2IP1
SSP2IP0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
BCL2IP<2:0>: MSSP2 I2C™ Bus Collision Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SSP2IP<2:0>: MSSP2 SPI/I2C Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS33030A-page 112
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-29:
IPC15: INTERRUPT PRIORITY CONTROL REGISTER 15
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
RTCIP2
RTCIP1
RTCIP0
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
RTCIP<2:0>: Real-Time Clock and Calendar Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7-0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 113
PIC24FV16KM204 FAMILY
REGISTER 8-30:
IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
U2ERIP2
U2ERIP1
U2ERIP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
U1ERIP2
U1ERIP1
U1ERIP0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
U2ERIP<2:0>: UART2 Error Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
U1ERIP<2:0>: UART1 Error Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS33030A-page 114
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-31:
IPC18: INTERRUPT PRIORITY CONTROL REGISTER 18
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
HLVDIP2
HLVDIP1
HLVDIP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-3
Unimplemented: Read as ‘0’
bit 2-0
HLVDIP<2:0>: High/Low-Voltage Detect Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 115
PIC24FV16KM204 FAMILY
REGISTER 8-32:
IPC19: INTERRUPT PRIORITY CONTROL REGISTER 19
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
DAC2IP2
DAC2IP1
DAC2IP0
—
DAC1IP2
DAC1IP1
DAC1IP0
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
CTMUIP2
CTMUIP1
CTMUIP0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
DAC2IP<2:0>: Digital-to-Analog Converter 2 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
DAC1IP<2:0>: Digital-to-Analog Converter 1 Event Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
CTMUIP<2:0>: CTMU Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS33030A-page 116
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 8-33:
IPC20: INTERRUPT PRIORITY CONTROL REGISTER 20
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-1
R/W-0
R/W-0
—
—
—
—
—
ULPWUIP2
ULPWUIP1
ULPWUIP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-3
Unimplemented: Read as ‘0’
bit 2-0
ULPWUIP<2:0>: Ultra Low-Power Wake-up Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
REGISTER 8-34:
IPC24: INTERRUPT PRIORITY CONTROL REGISTER 24
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-1
R/W-0
R/W-0
U-0
R/W-1
R/W-0
R/W-0
—
CLC2IP2
CLC2IP1
CLC2IP0
—
CLC1IP2
CLC1IP1
CLC1IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-7
Unimplemented: Read as ‘0’
bit 6-4
CLC2IP<2:0>: CLC2 Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
CLC1IP<2:0>: CLC1 Interrupt Priority bits
111 = Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is Priority 1
000 = Interrupt source is disabled
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 117
PIC24FV16KM204 FAMILY
REGISTER 8-35:
INTTREG: INTERRUPT CONTROL AND STATUS REGISTER
R-0
U-0
R/W-0
U-0
R-0
R-0
R-0
R-0
CPUIRQ
—
VHOLD
—
ILR3
ILR2
ILR1
ILR0
bit 15
bit 8
U-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
—
VECNUM6
VECNUM5
VECNUM4
VECNUM3
VECNUM2
VECNUM1
VECNUM0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CPUIRQ: Interrupt Request from Interrupt Controller CPU bit
1 = An interrupt request has occurred but has not yet been Acknowledged by the CPU (this will
happen when the CPU priority is higher than the interrupt priority)
0 = No interrupt request is left unacknowledged
bit 14
Unimplemented: Read as ‘0’
bit 13
VHOLD: Vector Hold bit
Allows Vector Number Capture and Changes which Interrupt is Stored in the VECNUM<6:0> bits:
1 = VECNUM<6:0> will contain the value of the highest priority pending interrupt, instead of the
current interrupt
0 = VECNUM<6:0> will contain the value of the last Acknowledged interrupt (last interrupt that has
occurred with higher priority than the CPU, even if other interrupts are pending)
bit 12
Unimplemented: Read as ‘0’
bit 11-8
ILR<3:0>: New CPU Interrupt Priority Level bits
1111 = CPU Interrupt Priority Level is 15
•
•
•
0001 = CPU Interrupt Priority Level is 1
0000 = CPU Interrupt Priority Level is 0
bit 7
Unimplemented: Read as ‘0’
bit 6-0
VECNUM<6:0>: Vector Number of Pending Interrupt bits
0111111 = Interrupt vector pending is Number 135
•
•
•
0000001 = Interrupt vector pending is Number 9
0000000 = Interrupt vector pending is Number 8
DS33030A-page 118
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
8.4
Interrupt Setup Procedures
8.4.1
INITIALIZATION
To configure an interrupt source:
1.
2.
Set the NSTDIS control bit (INTCON1<15>) if
nested interrupts are not desired.
Select the user-assigned priority level for the
interrupt source by writing the control bits in the
appropriate IPCx register. The priority level will
depend on the specific application and type of
interrupt source. If multiple priority levels are not
desired, the IPCx register control bits for all
enabled interrupt sources may be programmed
to the same non-zero value.
Note:
3.
4.
At a device Reset, the IPCx registers are
initialized, such that all user interrupt
sources are assigned to Priority Level 4.
Clear the interrupt flag status bit associated with
the peripheral in the associated IFSx register.
Enable the interrupt source by setting the
interrupt enable control bit associated with the
source in the appropriate IECx register.
8.4.2
8.4.3
TRAP SERVICE ROUTINE (TSR)
A Trap Service Routine (TSR) is coded like an ISR,
except that the appropriate trap status flag in the
INTCON1 register must be cleared to avoid re-entry
into the TSR.
8.4.4
INTERRUPT DISABLE
All user interrupts can be disabled using the following
procedure:
1.
2.
Push the current SR value onto the software
stack using the PUSH instruction.
Force the CPU to Priority Level 7 by inclusive
ORing the value, 0Eh, with SRL.
To enable user interrupts, the POP instruction may be
used to restore the previous SR value.
Only user interrupts with a priority level of 7 or less can
be disabled. Trap sources (Level 8-15) cannot be
disabled.
The DISI instruction provides a convenient way to
disable interrupts of Priority Levels 1-6 for a fixed
period. Level 7 interrupt sources are not disabled by
the DISI instruction.
INTERRUPT SERVICE ROUTINE
The method that is used to declare an ISR (Interrupt
Service Routine) and initialize the IVT with the correct
vector address depends on the programming language
(i.e., C or assembly), and the language development
toolsuite that is used to develop the application. In
general, the user must clear the interrupt flag in the
appropriate IFSx register for the source of the interrupt
that the ISR handles. Otherwise, the ISR will be
re-entered immediately after exiting the routine. If the
ISR is coded in assembly language, it must be terminated using a RETFIE instruction to unstack the saved
PC value, SRL value and old CPU priority level.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 119
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 120
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
9.0
OSCILLATOR
CONFIGURATION
Note:
• On-chip 4x Phase Locked Loop (PLL) to boost
internal operating frequency on select internal and
external oscillator sources.
• Software-controllable switching between various
clock sources.
• Software-controllable postscaler for selective
clocking of CPU for system power savings.
• System frequency range declaration bits for EC
mode. When using an external clock source, the
current consumption is reduced by setting the
declaration bits to the expected frequency range.
• A Fail-Safe Clock Monitor (FSCM) that detects clock
failure and permits safe application recovery or
shutdown.
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on
oscillator configuration, refer to the
“PIC24F Family Reference Manual”,
Section 38. “Oscillator with 500 kHz
Low-Power FRC” (DS39726).
The oscillator system for the PIC24FV16KM204 family
of devices has the following features:
• A total of five external and internal oscillator options
as clock sources, providing 11 different clock
modes.
FIGURE 9-1:
A simplified diagram of the oscillator system is shown in
Figure 9-1.
PIC24FV16KM204 FAMILY CLOCK DIAGRAM
Primary Oscillator
REFOCON<15:8>
XT, HS, EC
OSCO
OSCI
4 x PLL
8 MHz
4 MHz
Postscaler
8 MHz
FRC
Oscillator
500 kHz
LPFRC
Oscillator
Reference Clock
Generator
XTPLL, HSPLL
ECPLL, FRCPLL
REFO
FRCDIV
Peripherals
CLKDIV<10:8>
FRC
CLKO
LPRC
Postscaler
LPRC
Oscillator
31 kHz (nominal)
Secondary Oscillator
SOSC
SOSCO
SOSCI
CPU
CLKDIV<14:12>
SOSCEN
Enable
Oscillator
Clock Control Logic
Fail-Safe
Clock
Monitor
WDT, PWRT, DSWDT
Clock Source Option
for Other Modules
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 121
PIC24FV16KM204 FAMILY
9.1
CPU Clocking Scheme
9.2
The system clock source can be provided by one of
four sources:
• Primary Oscillator (POSC) on the OSCI and OSCO
pins
• Secondary Oscillator (SOSC) on the SOSCI and
SOSCO pins
The PIC24FV16KM204 family devices consist of
two types of secondary oscillator:
- High-Power Secondary Oscillator
- Low-Power Secondary Oscillator
These can be selected by using the SOSCSEL
(FOSC<5>) bit.
• Fast Internal RC (FRC) Oscillator
- 8 MHz FRC Oscillator
- 500 kHz Lower Power FRC Oscillator
• Low-Power Internal RC (LPRC) Oscillator with two
modes:
- High-Power/High-Accuracy mode
- Low-Power/Low-Accuracy mode
The primary oscillator and 8 MHz FRC sources have the
option of using the internal 4x PLL. The frequency of the
FRC clock source can optionally be reduced by the programmable clock divider. The selected clock source
generates the processor and peripheral clock sources.
The processor clock source is divided by two to produce
the internal instruction cycle clock, FCY. In this
document, the instruction cycle clock is also denoted by
FOSC/2. The internal instruction cycle clock, FOSC/2, can
be provided on the OSCO I/O pin for some operating
modes of the primary oscillator.
TABLE 9-1:
Initial Configuration on POR
The oscillator source (and operating mode) that is used
at a device Power-on Reset (POR) event is selected
using Configuration bit settings. The Oscillator
Configuration bit settings are located in the
Configuration registers in the program memory (for
more information, see Section 26.1 “Configuration
Bits”). The Primary Oscillator Configuration bits,
POSCMD<1:0> (FOSC<1:0>), and the Initial Oscillator
Select
Configuration
bits,
FNOSC<2:0>
(FOSCSEL<2:0>), select the oscillator source that is
used at a POR. The FRC Primary Oscillator with
Postscaler (FRCDIV) is the default (unprogrammed)
selection. The secondary oscillator, or one of the
internal oscillators, may be chosen by programming
these bit locations. The EC mode Frequency Range
Configuration bits, POSCFREQ<1:0> (FOSC<4:3>),
optimize power consumption when running in EC
mode. The default configuration is “frequency range is
greater than 8 MHz”.
The Configuration bits allow users to choose between
the various clock modes, shown in Table 9-1.
9.2.1
CLOCK SWITCHING MODE
CONFIGURATION BITS
The FCKSMx Configuration bits (FOSC<7:6>) are
used jointly to configure device clock switching and the
FSCM. Clock switching is enabled only when FCKSM1
is programmed (‘0’). The FSCM is enabled only when
FCKSM<1:0> are both programmed (‘00’).
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
Oscillator Mode
Oscillator Source
POSCMD<1:0>
FNOSC<2:0>
8 MHz FRC Oscillator with Postscaler (FRCDIV)
Internal
11
111
1, 2
500 kHz FRC Oscillator with Postscaler
(LPFRCDIV)
Internal
11
110
1
Low-Power RC Oscillator (LPRC)
Notes
Internal
11
101
1
Secondary
00
100
1
Primary
10
011
Primary Oscillator (EC) with PLL Module (ECPLL)
Primary
00
011
Primary Oscillator (HS)
Primary
10
010
Primary Oscillator (XT)
Primary
01
010
Primary Oscillator (EC)
Primary
00
010
8 MHz FRC Oscillator with PLL Module (FRCPLL)
Internal
11
001
1
8 MHz FRC Oscillator (FRC)
Internal
11
000
1
Secondary (Timer1) Oscillator (SOSC)
Primary Oscillator (HS) with PLL Module (HSPLL)
Note 1:
2:
The OSCO pin function is determined by the OSCIOFNC Configuration bit.
This is the default oscillator mode for an unprogrammed (erased) device.
DS33030A-page 122
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
9.3
Control Registers
The Clock Divider register (Register 9-2) controls the
features associated with Doze mode, as well as the
postscaler for the FRC oscillator.
The operation of the oscillator is controlled by three
Special Function Registers (SFRs):
The FRC Oscillator Tune register (Register 9-3) allows
the user to fine-tune the FRC oscillator over a range of
approximately ±5.25%. Each bit increment or decrement changes the factory calibrated frequency of the
FRC oscillator by a fixed amount.
• OSCCON
• CLKDIV
• OSCTUN
The OSCCON register (Register 9-1) is the main
control register for the oscillator. It controls clock
source switching and allows the monitoring of clock
sources.
REGISTER 9-1:
OSCCON: OSCILLATOR CONTROL REGISTER
U-0
R-0, HSC
R-0, HSC
R-0, HSC
U-0
R/W-x(1)
R/W-x(1)
R/W-x(1)
—
COSC2
COSC1
COSC0
—
NOSC2
NOSC1
NOSC0
bit 15
bit 8
R/SO-0, HSC
U-0
R-0, HSC(2)
U-0
R/CO-0, HS
R/W-0(3)
R/W-0
R/W-0
CLKLOCK
—
LOCK
—
CF
SOSCDRV
SOSCEN
OSWEN
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
HS = Hardware Settable bit
CO = Clearable Only bit
SO = Settable Only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
COSC<2:0>: Current Oscillator Selection bits
111 = 8 MHz Fast RC Oscillator with Postscaler (FRCDIV)
110 = 500 kHz Low-Power Fast RC Oscillator (FRC) with Postscaler (LPFRCDIV)
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL)
010 = Primary Oscillator (XT, HS, EC)
001 = 8 MHz FRC Oscillator with Postscaler and PLL module (FRCPLL)
000 = 8 MHz FRC Oscillator (FRC)
bit 11
Unimplemented: Read as ‘0’
bit 10-8
NOSC<2:0>: New Oscillator Selection bits(1)
111 = 8 MHz Fast RC Oscillator with Postscaler (FRCDIV)
110 = 500 kHz Low-Power Fast RC Oscillator (FRC) with Postscaler (LPFRCDIV)
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL)
010 = Primary Oscillator (XT, HS, EC)
001 = 8 MHz FRC Oscillator with Postscaler and PLL module (FRCPLL)
000 = 8 MHz FRC Oscillator (FRC)
Note 1:
2:
3:
Reset values for these bits are determined by the FNOSCx Configuration bits.
This bit also resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected.
When SOSC is selected to run from a digital clock input, rather than an external crystal (SOSCSRC = 0),
this bit has no effect.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 123
PIC24FV16KM204 FAMILY
REGISTER 9-1:
OSCCON: OSCILLATOR CONTROL REGISTER (CONTINUED)
bit 7
CLKLOCK: Clock Selection Lock Enable bit
If FSCM is Enabled (FCKSM1 = 1):
1 = Clock and PLL selections are locked
0 = Clock and PLL selections are not locked and may be modified by setting the OSWEN bit
If FSCM is Disabled (FCKSM1 = 0):
Clock and PLL selections are never locked and may be modified by setting the OSWEN bit.
bit 6
Unimplemented: Read as ‘0’
bit 5
LOCK: PLL Lock Status bit(2)
1 = PLL module is in lock or PLL module start-up timer is satisfied
0 = PLL module is out of lock, PLL start-up timer is running or PLL is disabled
bit 4
Unimplemented: Read as ‘0’
bit 3
CF: Clock Fail Detect bit
1 = FSCM has detected a clock failure
0 = No clock failure has been detected
bit 2
SOSCDRV: Secondary Oscillator Drive Strength bit(3)
1 = High-power SOSC circuit is selected
0 = Low/high-power select is done via the SOSCSRC Configuration bit
bit 1
SOSCEN: 32 kHz Secondary Oscillator (SOSC) Enable bit
1 = Enables the secondary oscillator
0 = Disables the secondary oscillator
bit 0
OSWEN: Oscillator Switch Enable bit
1 = Initiates an oscillator switch to the clock source specified by the NOSC<2:0> bits
0 = Oscillator switch is complete
Note 1:
2:
3:
Reset values for these bits are determined by the FNOSCx Configuration bits.
This bit also resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected.
When SOSC is selected to run from a digital clock input, rather than an external crystal (SOSCSRC = 0),
this bit has no effect.
DS33030A-page 124
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 9-2:
CLKDIV: CLOCK DIVIDER REGISTER
R/W-0
R/W-0
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
R/W-1
ROI
DOZE2
DOZE1
DOZE0
DOZEN(1)
RCDIV2
RCDIV1
RCDIV0
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ROI: Recover on Interrupt bit
1 = Interrupts clear the DOZEN bit, and reset the CPU and peripheral clock ratio to 1:1
0 = Interrupts have no effect on the DOZEN bit
bit 14-12
DOZE<2:0>: CPU and Peripheral Clock Ratio Select bits
111 = 1:128
110 = 1:64
101 = 1:32
100 = 1:16
011 = 1:8
010 = 1:4
001 = 1:2
000 = 1:1
bit 11
DOZEN: Doze Enable bit(1)
1 = DOZE<2:0> bits specify the CPU and peripheral clock ratio
0 = CPU and peripheral clock ratio are set to 1:1
bit 10-8
RCDIV<2:0>: FRC Postscaler Select bits
When COSC<2:0> (OSCCON<14:12>) = 111:
111 = 31.25 kHz (divide-by-256)
110 = 125 kHz (divide-by-64)
101 = 250 kHz (divide-by-32)
100 = 500 kHz (divide-by-16)
011 = 1 MHz (divide-by-8)
010 = 2 MHz (divide-by-4)
001 = 4 MHz (divide-by-2) – default
000 = 8 MHz (divide-by-1)
When COSC<2:0> (OSCCON<14:12>) = 110:
111 = 1.95 kHz (divide-by-256)
110 = 7.81 kHz (divide-by-64)
101 = 15.62 kHz (divide-by-32)
100 = 31.25 kHz (divide-by-16)
011 = 62.5 kHz (divide-by-8)
010 = 125 kHz (divide-by-4)
001 = 250 kHz (divide-by-2) – default
000 = 500 kHz (divide-by-1)
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
This bit is automatically cleared when the ROI bit is set and an interrupt occurs.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 125
PIC24FV16KM204 FAMILY
REGISTER 9-3:
OSCTUN: FRC OSCILLATOR TUNE REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
—
—
R/W-0
TUN5
R/W-0
(1)
(1)
TUN4
R/W-0
(1)
TUN3
R/W-0
TUN2
(1)
R/W-0
TUN1
(1)
R/W-0
TUN0(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-6
Unimplemented: Read as ‘0’
bit 5-0
TUN<5:0>: FRC Oscillator Tuning bits(1)
011111 = Maximum frequency deviation
011110
•
•
•
000001
000000 = Center frequency, oscillator is running at factory calibrated frequency
111111
•
•
•
100001
100000 = Minimum frequency deviation
Note 1:
Increments or decrements of TUN<5:0> may not change the FRC frequency in equal steps over the FRC
tuning range and may not be monotonic.
DS33030A-page 126
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
9.4
Clock Switching Operation
With few limitations, applications are free to switch
between any of the four clock sources (POSC, SOSC,
FRC and LPRC) under software control and at any
time. To limit the possible side effects that could result
from this flexibility, PIC24F devices have a safeguard
lock built into the switching process.
Note:
9.4.1
The Primary Oscillator mode has three
different submodes (XT, HS and EC),
which are determined by the POSCMDx
Configuration bits. While an application
can switch to and from Primary Oscillator
mode in software, it cannot switch
between the different primary submodes
without reprogramming the device.
ENABLING CLOCK SWITCHING
To enable clock switching, the FCKSM1 Configuration bit
in the FOSC Configuration register must be programmed
to ‘0’. (Refer to Section 26.0 “Special Features” for
further details.) If the FCKSM1 Configuration bit is
unprogrammed (‘1’), the clock switching function and
FSCM function are disabled; this is the default setting.
The NOSCx control bits (OSCCON<10:8>) do not
control the clock selection when clock switching is
disabled. However, the COSCx bits (OSCCON<14:12>)
will reflect the clock source selected by the FNOSCx
Configuration bits.
The OSWEN control bit (OSCCON<0>) has no effect
when clock switching is disabled; it is held at ‘0’ at all
times.
9.4.2
OSCILLATOR SWITCHING
SEQUENCE
At a minimum, performing a clock switch requires this
basic sequence:
1.
2.
3.
4.
5.
If
desired,
read
the
COSCx
bits
(OSCCON<14:12>) to determine the current
oscillator source.
Perform the unlock sequence to allow a write to
the OSCCON register high byte.
Write the appropriate value to the NOSCx bits
(OSCCON<10:8>) for the new oscillator source.
Perform the unlock sequence to allow a write to
the OSCCON register low byte.
Set the OSWEN bit to initiate the oscillator
switch.
 2013 Microchip Technology Inc.
Once the basic sequence is completed, the system
clock hardware responds automatically, as follows:
1.
2.
3.
4.
5.
6.
The clock switching hardware compares the
COSCx bits with the new value of the NOSCx
bits. If they are the same, then the clock switch
is a redundant operation. In this case, the
OSWEN bit is cleared automatically and the
clock switch is aborted.
If a valid clock switch has been initiated, the
LOCK (OSCCON<5>) and CF (OSCCON<3>)
bits are cleared.
The new oscillator is turned on by the hardware
if it is not currently running. If a crystal oscillator
must be turned on, the hardware will wait until
the OST expires. If the new source is using the
PLL, then the hardware waits until a PLL lock is
detected (LOCK = 1).
The hardware waits for 10 clock cycles from the
new clock source and then performs the clock
switch.
The hardware clears the OSWEN bit to indicate a
successful clock transition. In addition, the
NOSCx bits value is transferred to the COSCx
bits.
The old clock source is turned off at this time,
with the exception of LPRC (if WDT, FSCM or
RTCC with LPRC as a clock source is enabled)
or SOSC (if SOSCEN remains enabled).
Note 1: The processor will continue to execute
code throughout the clock switching
sequence. Timing-sensitive code should
not be executed during this time.
2: Direct clock switches between any
Primary Oscillator mode with PLL and
FRCPLL mode are not permitted. This
applies to clock switches in either direction. In these instances, the application
must switch to FRC mode as a transition
clock source between the two PLL
modes.
Advance Information
DS33030A-page 127
PIC24FV16KM204 FAMILY
The following code sequence for a clock switch is
recommended:
1.
2.
3.
4.
5.
6.
7.
8.
Disable interrupts during the OSCCON register
unlock and write sequence.
Execute the unlock sequence for the OSCCON
high byte by writing 78h and 9Ah to
OSCCON<15:8>,
in
two
back-to-back
instructions.
Write the new oscillator source to the NOSCx
bits in the instruction immediately following the
unlock sequence.
Execute the unlock sequence for the OSCCON
low byte by writing 46h and 57h to
OSCCON<7:0>, in two back-to-back instructions.
Set the OSWEN bit in the instruction immediately
following the unlock sequence.
Continue to execute code that is not
clock-sensitive (optional).
Invoke an appropriate amount of software delay
(cycle counting) to allow the selected oscillator
and/or PLL to start and stabilize.
Check to see if OSWEN is ‘0’. If it is, the switch
was successful. If OSWEN is still set, then check
the LOCK bit to determine the cause of failure.
The core sequence for unlocking the OSCCON register
and initiating a clock switch is shown in Example 9-1
and Example 9-2.
EXAMPLE 9-1:
ASSEMBLY CODE
SEQUENCE FOR CLOCK
SWITCHING
;Place the new oscillator selection in W0
;OSCCONH (high byte) Unlock Sequence
MOV
#OSCCONH, w1
MOV
#0x78, w2
MOV
#0x9A, w3
MOV.b
w2, [w1]
MOV.b
w3, [w1]
;Set new oscillator selection
MOV.b
WREG, OSCCONH
;OSCCONL (low byte) unlock sequence
MOV
#OSCCONL, w1
MOV
#0x46, w2
MOV
#0x57, w3
MOV.b
w2, [w1]
MOV.b
w3, [w1]
;Start oscillator switch operation
BSET
OSCCON,#0
DS33030A-page 128
EXAMPLE 9-2:
BASIC ‘C’ CODE
SEQUENCE FOR CLOCK
SWITCHING
//Use compiler built-in function to write
new clock setting
__builtin_write_OSCCONH(0x01); //0x01
switches to FRCPLL
//Use compiler built-in function to set the
OSWEN bit.
__builtin_write_OSCCONL(OSCCONL | 0x01);
//Optional: Wait for clock switch sequence
to complete
while(OSCCONbits.OSWEN == 1);
9.5
Reference Clock Output
In addition to the CLKO output (FOSC/2) available in
certain oscillator modes, the device clock in the
PIC24FV16KM204 family devices can also be
configured to provide a reference clock output signal to
a port pin. This feature is available in all oscillator
configurations and allows the user to select a greater
range of clock submultiples to drive external devices in
the application.
This reference clock output is controlled by the
REFOCON register (Register 9-4). Setting the ROEN
bit (REFOCON<15>) makes the clock signal available
on the REFO pin. The RODIVx bits (REFOCON<11:8>)
enable the selection of 16 different clock divider
options.
The ROSSLP and ROSEL bits (REFOCON<13:12>)
control the availability of the reference output during
Sleep mode. The ROSEL bit determines if the oscillator
on OSC1 and OSC2, or the current system clock
source, is used for the reference clock output. The
ROSSLP bit determines if the reference source is
available on REFO when the device is in Sleep mode.
To use the reference clock output in Sleep mode, both
the ROSSLP and ROSEL bits must be set. The device
clock must also be configured for one of the primary
modes (EC, HS or XT); otherwise, if the ROSEL bit is
not also set, the oscillator on OSC1 and OSC2 will be
powered down when the device enters Sleep mode.
Clearing the ROSEL bit allows the reference output
frequency to change as the system clock changes
during any clock switches.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 9-4:
REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ROEN
—
ROSSLP
ROSEL
RODIV3
RODIV2
RODIV1
RODIV0
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ROEN: Reference Oscillator Output Enable bit
1 = Reference oscillator is enabled on the REFO pin
0 = Reference oscillator is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
ROSSLP: Reference Oscillator Output Stop in Sleep bit
1 = Reference oscillator continues to run in Sleep
0 = Reference oscillator is disabled in Sleep
bit 12
ROSEL: Reference Oscillator Source Select bit
1 = Primary oscillator is used as the base clock(1)
0 = System clock is used as the base clock; base clock reflects any clock switching of the device
bit 11-8
RODIV<3:0>: Reference Oscillator Divisor Select bits
1111 = Base clock value divided by 32,768
1110 = Base clock value divided by 16,384
1101 = Base clock value divided by 8,192
1100 = Base clock value divided by 4,096
1011 = Base clock value divided by 2,048
1010 = Base clock value divided by 1,024
1001 = Base clock value divided by 512
1000 = Base clock value divided by 256
0111 = Base clock value divided by 128
0110 = Base clock value divided by 64
0101 = Base clock value divided by 32
0100 = Base clock value divided by 16
0011 = Base clock value divided by 8
0010 = Base clock value divided by 4
0001 = Base clock value divided by 2
0000 = Base clock value
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
The crystal oscillator must be enabled using the FOSC<2:0> bits; the crystal maintains the operation in
Sleep mode.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 129
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 130
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
10.0
POWER-SAVING FEATURES
Note:
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information, refer to the
“PIC24F Family Reference Manual”,
Section 57. “Power-Saving Features
with VBAT” (DS30622).
This FRM describes some features which
are not implemented in this device. Sections
related to the VBAT pin and Deep Sleep do
not apply to the PIC24FV16KM204 family.
The PIC24FV16KM204 family of devices provides the
ability to manage power consumption by selectively
managing clocking to the CPU and the peripherals. In
general, a lower clock frequency and a reduction in the
number of circuits being clocked constitutes lower
consumed power. All PIC24F devices manage power
consumption in four different ways:
•
•
•
•
Clock Frequency
Instruction-Based Sleep and Idle modes
Software Controlled Doze mode
Selective Peripheral Control in Software
Combinations of these methods can be used to
selectively tailor an application’s power consumption,
while still maintaining critical application features, such
as timing-sensitive communications.
10.1
Clock Frequency and Clock
Switching
PIC24F devices allow for a wide range of clock
frequencies to be selected under application control. If
the system clock configuration is not locked, users can
choose low-power or high-precision oscillators by simply
changing the NOSCx bits. The process of changing a
system clock during operation, as well as limitations to
the process, are discussed in more detail in Section 9.0
“Oscillator Configuration”.
10.2
Instruction-Based Power-Saving
Modes
The ‘C’ syntax of the PWRSAV instruction is shown in
Example 10-1.
Note:
SLEEP_MODE and IDLE_MODE are
constants defined in the assembler
include file for the selected device.
Sleep and Idle modes can be exited as a result of an
enabled interrupt, WDT time-out or a device Reset.
When the device exits these modes, it is said to
“wake-up”.
10.2.1
SLEEP MODE
Sleep mode includes these features:
• The system clock source is shut down. If an
on-chip oscillator is used, it is turned off.
• The device current consumption will be reduced
to a minimum provided that no I/O pin is sourcing
current.
• The I/O pin directions and states are frozen.
• The Fail-Safe Clock Monitor does not operate
during Sleep mode since the system clock source
is disabled.
• The LPRC clock will continue to run in Sleep
mode if the WDT or RTCC with LPRC as the clock
source is enabled.
• The WDT, if enabled, is automatically cleared
prior to entering Sleep mode.
• Some device features or peripherals may
continue to operate in Sleep mode. This includes
items, such as the Input Change Notification on
the I/O ports or peripherals that use an external
clock input. Any peripheral that requires the system clock source for its operation will be disabled
in Sleep mode.
The device will wake-up from Sleep mode on any of
these events:
• On any interrupt source that is individually
enabled
• On any form of device Reset
• On a WDT time-out
On wake-up from Sleep, the processor will restart with
the same clock source that was active when Sleep
mode was entered.
PIC24F devices have two special power-saving modes
that are entered through the execution of a special
PWRSAV instruction. Sleep mode stops clock operation
and halts all code execution; Idle mode halts the CPU
and code execution, but allows peripheral modules to
continue operation.
EXAMPLE 10-1:
Sleep();
Idle();
‘C’ POWER-SAVING ENTRY
//Put the device into Sleep mode
//Put the device into Idle mode
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 131
PIC24FV16KM204 FAMILY
10.2.2
IDLE MODE
See Example 10-2 for initializing the ULPWU module.
Idle mode includes these features:
• The CPU will stop executing instructions.
• The WDT is automatically cleared.
• The system clock source remains active. By
default, all peripheral modules continue to operate
normally from the system clock source, but can
also be selectively disabled (see Section 10.6
“Selective Peripheral Module Control”).
• If the WDT or FSCM is enabled, the LPRC will
also remain active.
The device will wake from Idle mode on any of these
events:
• Any interrupt that is individually enabled
• Any device Reset
• A WDT time-out
On wake-up from Idle, the clock is re-applied to the
CPU and instruction execution begins immediately,
starting with the instruction following the PWRSAV
instruction or the first instruction in the ISR.
10.2.3
INTERRUPTS COINCIDENT WITH
POWER SAVE INSTRUCTIONS
Any interrupt that coincides with the execution of a
PWRSAV instruction will be held off until entry into Sleep
or Idle mode has completed. The device will then
wake-up from Sleep or Idle mode.
10.2.3.1
Power-on Resets (PORs)
VDD voltage is monitored to produce PORs. When a true
POR occurs, the entire device is reset.
10.3
Ultra Low-Power Wake-up
The Ultra Low-Power Wake-up (ULPWU) on pin, RB0,
allows a slow falling voltage to generate an interrupt
without excess current consumption.
To use this feature:
1.
2.
3.
4.
5.
Charge the capacitor on RB0 by configuring the
RB0 pin to an output and setting it to ‘1’.
Stop charging the capacitor by configuring RB0
as an input.
Discharge the capacitor by setting the ULPEN
and ULPSINK bits in the ULPWCON register.
Configure Sleep mode.
Enter Sleep mode.
When the voltage on RB0 drops below VIL, the device
wakes up and executes the next instruction.
This feature provides a low-power technique for
periodically waking up the device from Sleep mode.
The time-out is dependent on the discharge time of the
RC circuit on RB0.
When the ULPWU module wakes the device from
Sleep mode, the ULPWUIF bit (IFS5<0>) is set. Software can check this bit upon wake-up to determine the
wake-up source.
DS33030A-page 132
EXAMPLE 10-2:
ULTRA LOW-POWER
WAKE-UP INITIALIZATION
//*******************************
// 1. Charge the capacitor on RB0
//*******************************
TRISBbits.TRISB0 = 0;
LATBbits.LATB0 = 1;
for(i = 0; i < 10000; i++) Nop();
//*****************************
//2. Stop Charging the capacitor
//
on RB0
//*****************************
TRISBbits.TRISB0 = 1;
//*****************************
//3. Enable ULPWU Interrupt
//*****************************
IFS5bits.ULPWUIF = 0;
IEC5bits.ULPWUIE = 1;
IPC21bits.ULPWUIP = 0x7;
//*****************************
//4. Enable the Ultra Low Power
//
Wakeup module and allow
//
capacitor discharge
//*****************************
ULPWCONbits.ULPEN = 1;
ULPWCONbit.ULPSINK = 1;
//*****************************
//5. Enter Sleep Mode
//*****************************
Sleep();
//for sleep, execution will
//resume here
A series resistor, between RB0 and the external
capacitor provides overcurrent protection for the
AN2/ULPWU/RB0 pin and enables software calibration
of the time-out (see Figure 10-1).
FIGURE 10-1:
RB0
SERIES RESISTOR
R1
C1
A timer can be used to measure the charge time and
discharge time of the capacitor. The charge time can
then be adjusted to provide the desired delay in Sleep.
This technique compensates for the affects of temperature, voltage and component accuracy. The peripheral
can also be configured as a simple, programmable
Low-Voltage Detect (LVD) or temperature sensor.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 10-1:
ULPWCON: ULPWU CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
R/W-0
ULPEN
—
ULPSIDL
—
—
—
—
ULPSINK
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
ULPEN: ULPWU Module Enable bit
1 = Module is enabled
0 = Module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
ULPSIDL: ULPWU Stop in Idle Select bit
1 = Discontinues module operation when the device enters Idle mode
0 = Continues module operation in Idle mode
bit 12-9
Unimplemented: Read as ‘0’
bit 8
ULPSINK: ULPWU Current Sink Enable bit
1 = Current sink is enabled
0 = Current sink is disabled
bit 7-0
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
x = Bit is unknown
DS33030A-page 133
PIC24FV16KM204 FAMILY
10.4
Voltage Regulator-Based
Power-Saving Features
10.4.3
The PIC24FV16KM204 family series devices have a
voltage regulator that has the ability to alter
functionality to provide power savings. The on-chip
regulator is made up of two basic modules: the Voltage
Regulator (VREG) and the Retention Regulator
(RETREG). With the combination of VREG and
RETREG, the following power modes are available:
10.4.1
RUN MODE
In Run mode, the main VREG is providing a regulated
voltage with enough current to supply a device running
at full speed and the device is not in Sleep Mode. The
RETREG may or may not be running, but is unused.
10.4.2
In Sleep mode, the device is in Sleep and the main
VREG is providing a regulated voltage to the core. By
default, in Sleep mode, the regulator enters a
low-power standby state which consumes reduced
quiescent current. The PMSLP bit (RCON<8>) controls
the regulator state in Sleep mode. If the PMSLP bit is
set, the program Flash memory will stay powered on
during Sleep mode and the regulator will stay in its
full-power mode.
TABLE 10-1:
The Retention Regulator, sometimes referred to as the
low-voltage regulator, is designed to provide power to
the core at a lower voltage than the standard voltage
regulator, while consuming significantly lower quiescent
current. Refer to Section 27.0 “Electrical Characteristics” for the voltage output range of the RETREG. This
regulator is only used in Sleep mode, and has limited
output current to maintain the RAM and provide power
for limited peripherals, such as the WDT, while the
device is in Sleep. It is controlled by the RETCFG Configuration bit (FPOR<2>) and in firmware by the RETEN
bit (RCON<12>). RETCFG must be programmed (= 0)
and the RETEN bit must be set (= 1) for the Retention
Regulator to be enabled.
10.4.4
SLEEP MODE
RETENTION REGULATOR
RETENTION SLEEP MODE
In Retention Sleep mode, the device is in Sleep and all
regulated voltage is provided solely by the RETREG,
while the main VREG is disabled. Consequently, this
mode provides the lowest Sleep power consumption,
but has a trade-off of a longer wake-up time. The
low-voltage Sleep wake-up time is longer than Sleep
mode due to the extra time required to re-enable the
VREG and raise the VDDCORE supply rail back to
normal regulated levels.
Note:
The PIC24FV16KM204 family devices
do not have any internal voltage
regulation, and therefore, do not
support Retention Sleep mode.
VOLTAGE REGULATION CONFIGURATION SETTINGS FOR
PIC24FV16KM204 FAMILY DEVICES
RETCFG Bit
(FPOR<2>)
RETEN Bit
(RCON<12>
PMSLP Bit
(RCON<8>)
Power Mode
During Sleep
0
0
1
Sleep
Description
VREG mode (normal) is unchanged during Sleep.
RETREG is unused.
0
0
0
1
0
0
Sleep
VREG goes to Low-Power Standby mode during
Sleep.
(Standby)
RETREG is unused.
Retention
Sleep
VREG is off during Sleep.
1
x
1
Sleep
1
x
0
Sleep
RETREG is enabled and provides Sleep voltage
regulation.
VREG mode (normal) is unchanged during Sleep.
RETREG is disabled at all times.
(Standby)
DS33030A-page 134
VREG goes to Low-Power Standby mode during
Sleep.
RETREG is disabled at all times.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
10.5
Doze Mode
10.6
Generally, changing clock speed and invoking one of
the power-saving modes are the preferred strategies
for reducing power consumption. There may be
circumstances, however, where this is not practical. For
example, it may be necessary for an application to
maintain uninterrupted synchronous communication,
even while it is doing nothing else. Reducing system
clock speed may introduce communication errors,
while using a power-saving mode may stop
communications completely.
Doze mode is a simple and effective alternative method
to reduce power consumption while the device is still
executing code. In this mode, the system clock continues to operate from the same source and at the same
speed. Peripheral modules continue to be clocked at
the same speed, while the CPU clock speed is
reduced. Synchronization between the two clock
domains is maintained, allowing the peripherals to
access the SFRs while the CPU executes code at a
slower rate.
Doze mode is enabled by setting the DOZEN bit
(CLKDIV<11>). The ratio between peripheral and core
clock speed is determined by the DOZE<2:0> bits
(CLKDIV<14:12>). There are eight possible
configurations, from 1:1 to 1:128, with 1:1 being the
default.
It is also possible to use Doze mode to selectively reduce
power consumption in event driven applications. This
allows clock-sensitive functions, such as synchronous
communications, to continue without interruption. Meanwhile, the CPU Idles, waiting for something to invoke an
interrupt routine. Enabling the automatic return to
full-speed CPU operation on interrupts is enabled by
setting the ROI bit (CLKDIV<15>). By default, interrupt
events have no effect on Doze mode operation.
Selective Peripheral Module
Control
Idle and Doze modes allow users to substantially
reduce power consumption by slowing or stopping the
CPU clock. Even so, peripheral modules still remain
clocked, and thus, consume power. There may be
cases where the application needs what these modes
do not provide: the allocation of power resources to
CPU processing with minimal power consumption from
the peripherals.
PIC24F devices address this requirement by allowing
peripheral modules to be selectively disabled, reducing
or eliminating their power consumption. This can be
done with two control bits:
• The Peripheral Enable bit, generically named,
“XXXEN”, located in the module’s main control
SFR.
• The Peripheral Module Disable (PMD) bit,
generically named, “XXXMD”, located in one of
the PMDx Control registers.
Both bits have similar functions in enabling or disabling
its associated module. Setting the PMDx bits for a
module disables all clock sources to that module, reducing its power consumption to an absolute minimum. In
this state, the control and status registers associated
with the peripheral will also be disabled, so writes to
those registers will have no effect, and read values will
be invalid. Many peripheral modules have a
corresponding PMDx bit.
In contrast, disabling a module by clearing its XXXEN
bit, disables its functionality, but leaves its registers
available to be read and written to. Power consumption
is reduced, but not by as much as when the PMDx bits
are used. Most peripheral modules have an enable bit;
exceptions include capture, compare and RTCC.
To achieve more selective power savings, peripheral
modules can also be selectively disabled when the
device enters Idle mode. This is done through the control
bit of the generic name format, “XXXIDL”. By default, all
modules that can operate during Idle mode will do so.
Using the disable on Idle feature disables the module
while in Idle mode, allowing further reduction of power
consumption during Idle mode, enhancing power
savings for extremely critical power applications.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 135
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 136
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
11.0
Note:
I/O PORTS
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on the I/O
ports, refer to the “PIC24F Family
Reference Manual”, Section 12. “I/O
Ports with Peripheral Pin Select
(PPS)” (DS39711). Note that the
PIC24FV16KM204 family devices do not
support Peripheral Pin Select features.
All of the device pins (except VDD and VSS) are shared
between the peripherals and the parallel I/O ports. All
I/O input ports feature Schmitt Trigger inputs for
improved noise immunity.
11.1
Parallel I/O (PIO) Ports
A Parallel I/O port that shares a pin with a peripheral is,
in general, subservient to the peripheral. The peripheral’s
output buffer data and control signals are provided to a
pair of multiplexers. The multiplexers select whether the
peripheral or the associated port has ownership of the
output data and control signals of the I/O pin. The logic
also prevents “loop through”, in which a port’s digital
output can drive the input of a peripheral that shares the
same pin. Figure 11-1 illustrates how ports are shared
with other peripherals and the associated I/O pin to which
they are connected.
FIGURE 11-1:
When a peripheral is enabled and the peripheral is
actively driving an associated pin, the use of the pin as
a general purpose output pin is disabled. The I/O pin
may be read, but the output driver for the parallel port
bit will be disabled. If a peripheral is enabled, but the
peripheral is not actively driving a pin, that pin may be
driven by a port.
All port pins have three registers directly associated
with their operation as digital I/O. The Data Direction
register (TRISx) determines whether the pin is an input
or an output. If the data direction bit is a ‘1’, then the pin
is an input. All port pins are defined as inputs after a
Reset. Reads from the Data Latch register (LAT), read
the latch. Writes to the latch, write the latch. Reads
from the port (PORT), read the port pins; writes to the
port pins, write the latch.
Any bit and its associated data and control registers
that are not valid for a particular device will be
disabled. That means the corresponding LATx and
TRISx registers, and the port pin will read as zeros.
When a pin is shared with another peripheral or
function that is defined as an input only, it is
nevertheless regarded as a dedicated port because
there is no other competing source of outputs.
BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE
Peripheral Module
Output Multiplexers
Peripheral Input Data
Peripheral Module Enable
Peripheral Output Enable
Peripheral Output Data
Output Data
0
Read TRIS
WR TRIS
Output Enable
0
1
PIO Module
Data Bus
I/O
1
D
Q
I/O Pin
CK
TRIS Latch
D
WR LAT +
WR PORT
Q
CK
Data Latch
Read LAT
Input Data
Read PORT
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 137
PIC24FV16KM204 FAMILY
11.1.1
OPEN-DRAIN CONFIGURATION
When reading the PORTx register, all pins configured
as analog input channels will read as cleared (a low
level). Analog levels on any pin that is defined as a digital input (including the ANx pins) may cause the input
buffer to consume current that exceeds the device
specifications.
In addition to the PORT, LAT and TRIS registers for
data control, each port pin can also be individually configured for either digital or open-drain output. This is
controlled by the Open-Drain Control register, ODCx,
associated with each port. Setting any of the bits
configures the corresponding pin to act as an
open-drain output.
11.2.1
I/O pins with shared analog functionality, such as A/D
inputs and comparator inputs, must have their digital
inputs shut off when analog functionality is used. Note
that analog functionality includes an analog voltage
being applied to the pin externally.
The maximum open-drain voltage allowed is the same
as the maximum VIH specification.
11.2
Configuring Analog Port Pins
The use of the ANSx and TRISx registers control the
operation of the A/D port pins. The port pins that are
desired as analog inputs must have their corresponding TRISx bit set (input). If the TRISx bit is cleared
(output), the digital output level (VOH or VOL) will be
converted.
REGISTER 11-1:
ANALOG SELECTION REGISTER
To allow for analog control, the ANSx registers are
provided. There is one ANSx register for each port
(ANSA, ANSB and ANSC). Within each ANSx register,
there is a bit for each pin that shares analog
functionality with the digital I/O functionality.
If a particular pin does not have an analog function, that
bit is unimplemented. See Register 11-1 to Register 11-3
for implementation.
ANSA: ANALOG SELECTION (PORTA)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
—
—
—
ANSA4(1)
ANSA3
ANSA2
ANSA1
ANSA0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-5
Unimplemented: Read as ‘0’
bit 4-0
ANSA<4:0>: Analog Select Control bits(1)
1 = Digital input buffer is not active (use for analog input)
0 = Digital input buffer is active
Note 1:
x = Bit is unknown
The ANSA4 bit is not available on 20-pin devices.
DS33030A-page 138
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 11-2:
ANSB: ANALOG SELECTION (PORTB)
R/W-1
R/W-1
R/W-1
R/W-1
U-0
U-0
R/W-1
R/W-1
ANSB15
ANSB14
ANSB13
ANSB12
—
—
ANSB9
ANSB8
bit 15
bit 8
R/W-1
ANSB7
R/W-1
R/W-1
(1)
ANSB5
ANSB6
R/W-1
(1)
ANSB4
R/W-1
ANSB3
(1)
R/W-1
R/W-1
R/W-1
ANSB2
ANSB1
ANSB0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
ANSB<15:12>: Analog Select Control bits
1 = Digital input buffer is not active (use for analog input)
0 = Digital input buffer is active
bit 11-10
Unimplemented: Read as ‘0’
bit 9-0
ANSB<9:0>: Analog Select Control bits(1)
1 = Digital input buffer is not active (use for analog input)
0 = Digital input buffer is active
Note 1:
x = Bit is unknown
The ANSB<6:5,3> bits are not available on 20-pin devices.
REGISTER 11-3:
ANSC ANALOG SELECTION (PORTC)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
—
U-0
—
U-0
—
—
U-0
R/W-1
R/W-1
R/W-1
—
ANSC2(1,2)
ANSC1(1,2)
ANSC0(1,2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-3
Unimplemented: Read as ‘0’
bit 2-0
ANSC<2:0>: Analog Select Control bits(1,2)
1 = Digital input buffer is not active (use for analog input)
0 = Digital input buffer is active
Note 1:
2:
x = Bit is unknown
These bits are not implemented in 20-pin devices.
These bits are not implemented in 28-pin devices.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 139
PIC24FV16KM204 FAMILY
11.2.2
I/O PORT WRITE/READ TIMING
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically, this instruction
would be a NOP.
11.3
Input Change Notification (ICN)
The Input Change Notification function of the I/O ports
allows the PIC24FV16KM204 family of devices to
generate interrupt requests to the processor in
response to a Change-of-State (COS) on selected
input pins. This feature is capable of detecting input
Change-of-States, even in Sleep mode, when the
clocks are disabled. Depending on the device pin
count, there are up to 37 external signals (CN0 through
CN36) that may be selected (enabled) for generating
an interrupt request on a Change-of-State.
There are six control registers associated with the CN
module. The CNEN1 and CNEN3 registers contain the
interrupt enable control bits for each of the CNx input
pins. Setting any of these bits enables a CN interrupt
for the corresponding pins.
On any pin, only the pull-up resistor or the pull-down
resistor should be enabled, but not both of them. If the
push button or the keypad is connected to VDD, enable
the pull-down, or if they are connected to VSS, enable
the pull-up resistors. The pull-ups are enabled
separately using the CNPU1 and CNPU3 registers,
which contain the control bits for each of the CNx pins.
Setting any of the control bits enables the weak
pull-ups for the corresponding pins. The pull-downs are
enabled separately using the CNPD1 and CNPD3
registers, which contain the control bits for each of the
CNx pins. Setting any of the control bits enables the
weak pull-downs for the corresponding pins.
When the internal pull-up is selected, the pin uses VDD
as the pull-up source voltage. When the internal
pull-down is selected, the pins are pulled down to VSS
by an internal resistor. Make sure that there is no
external pull-up source/pull-down sink when the
internal pull-ups/pull-downs are enabled.
Note:
Each CNx pin also has a weak pull-up/pull-down
connected to it. The pull-ups act as a current source
that is connected to the pin. The pull-downs act as a
current sink to eliminate the need for external resistors
when push button or keypad devices are connected.
EXAMPLE 11-1:
MOV
MOV
NOP;
BTSS
PORT WRITE/READ EXAMPLE
0xFF00, W0;
W0, TRISB;
PORTB, #13;
Equivalent ‘C’ Code
TRISB = 0xFF00;
NOP();
if(PORTBbits.RB13 == 1)
{
}
DS33030A-page 140
Pull-ups and pull-downs on Change Notification (CN) pins should always be disabled
whenever the port pin is configured as a
digital output.
//Configure PORTB<15:8> as inputs and PORTB<7:0> as outputs
//Delay 1 cycle
//Next Instruction
//Configure PORTB<15:8> as inputs and PORTB<7:0> as outputs
//Delay 1 cycle
// execute following code if PORTB pin 13 is set.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
12.0
TIMER1
Note:
Figure 12-1 illustrates a block diagram of the 16-bit
Timer1 module.
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on timers,
refer to the “PIC24F Family Reference
Manual”, Section 14. “Timers” (DS39704).
To configure Timer1 for operation:
1.
2.
3.
The Timer1 module is a 16-bit timer which can serve as
the time counter for the Real-Time Clock (RTC) or
operate as a free-running, interval timer/counter. Timer1
can operate in three modes:
4.
5.
• 16-Bit Timer
• 16-Bit Synchronous Counter
• 16-Bit Asynchronous Counter
6.
Set the TON bit (= 1).
Select the timer prescaler ratio using the
TCKPS<1:0> bits.
Set the Clock and Gating modes using the TCS
and TGATE bits.
Set or clear the TSYNC bit to configure
synchronous or asynchronous operation.
Load the timer period value into the PR1
register.
If interrupts are required, set the Timer1 Interrupt
Enable bit, T1IE. Use the Timer1 Interrupt Priority
bits, T1IP<2:0>, to set the interrupt priority.
Timer1 also supports these features:
• Timer Gate Operation
• Selectable Prescaler Settings
• Timer Operation During CPU Idle and Sleep
modes
• Interrupt on 16-Bit Period Register Match or
Falling Edge of External Gate Signal
FIGURE 12-1:
16-BIT TIMER1 MODULE BLOCK DIAGRAM
TECS<1:0>
LPRC
TCKPS<1:0>
2
TON
SOSCO
Prescaler
1, 8, 64, 256
Gate
Sync
SOSCI
SOSCEN
TGATE
TCS
T1CK
FOSC/2
TGATE
Set T1IF
Reset
Q
D
Q
CK
TMR1
Sync
Equal
Comparator
TSYNC
PR1
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 141
PIC24FV16KM204 FAMILY
REGISTER 12-1:
T1CON: TIMER1 CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
R/W-0
R/W-0
TON
—
TSIDL
—
—
—
TECS1(1)
TECS0(1)
bit 15
bit 8
U-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
U-0
—
TGATE
TCKPS1
TCKPS0
—
TSYNC
TCS
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timer1 On bit
1 = Starts 16-bit Timer1
0 = Stops 16-bit Timer1
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Timer1 Stop in Idle Mode bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12-10
Unimplemented: Read as ‘0’
bit 9-8
TECS<1:0>: Timer1 Extended Clock Select bits(1)
11 = Reserved; do not use
10 = Timer1 uses the LPRC as the clock source
01 = Timer1 uses the external clock from T1CK
00 = Timer1 uses the Secondary Oscillator (SOSC) as the clock source
bit 7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timer1 Gated Time Accumulation Enable bit
When TCS = 1:
This bit is ignored.
When TCS = 0:
1 = Gated time accumulation is enabled
0 = Gated time accumulation is disabled
bit 5-4
TCKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3
Unimplemented: Read as ‘0’
bit 2
TSYNC: Timer1 External Clock Input Synchronization Select bit
When TCS = 1:
1 = Synchronizes external clock input
0 = Does not synchronize external clock input
When TCS = 0:
This bit is ignored.
bit 1
TCS: Timer1 Clock Source Select bit
1 = Timer1 clock source is selected by TECS<1:0>
0 = Internal clock (FOSC/2)
bit 0
Unimplemented: Read as ‘0’
Note 1:
x = Bit is unknown
The TECSx bits are valid only when TCS = 1.
DS33030A-page 142
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
13.0
Note:
CAPTURE/COMPARE/PWM/
TIMER MODULES (MCCP AND
SCCP)
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on the
MCCP/SCCP modules, refer to the
“PIC24F Family Reference Manual”.
PIC24FV16KM204 family devices include several
Capture/Compare/PWM/Timer base modules, which
provide the functionality of three different peripherals of
earlier PIC24F devices. The module can operate in one
of three major modes:
• General Purpose Timer
• Input Capture
• Output Compare/PWM
The module is provided in two different forms, distinguished by the number of PWM outputs that the
module can generate. Single output modules (SCCPs)
provide only one PWM output. Multiple output modules
(MCCPs) can provide up to six outputs and an
extended range of power control features, depending
on the pin count of the particular device. All other
features of the modules are identical.
A conceptual block diagram for the module is shown in
Figure 13-1. All three modes share a time base generator and a common Timer register pair (CCPxTMRH/L);
other shared hardware components are added as a
particular mode requires.
Each module has a total of seven control and status
registers:
•
•
•
•
•
•
•
CCPxCON1L (Register 13-1)
CCPxCON1H (Register 13-2)
CCPxCON2L (Register 13-3)
CCPxCON2H (Register 13-4)
CCPxCON3L (Register 13-5)
CCPxCON3H (Register 13-6)
CCPxSTATL (Register 13-7)
Each module also includes eight buffer/counter registers that serve as Timer Value registers or data holding
buffers:
• CCPxTMRH/CCPxTMRL (Timer High/Low
Counters)
• CCPxPRH/CCPxPRL (Timer Period High/Low)
• CCPxRA (Primary Output Compare Data Buffer)
• CCPxRB (Secondary Output Compare
Data Buffer)
• CCPxBUFH/CCPxBUFL (Input Capture High/Low
Buffers)
The SCCP and MCCP modules can be operated only
in one of the three major modes at any time. The other
modes are not available unless the module is
reconfigured for the new mode.
FIGURE 13-1:
MCCPx/SCCPx CONCEPTUAL BLOCK DIAGRAM TIMER CLOCK GENERATOR
CCPxIF
CCTxIF
External
Capture Input
Input Capture
Sync/Trigger Out
Special Trigger (to A/D)
Auxiliary Output (to CTMU)
Clock
Sources
Time Base
Generator
CCPxTMRH/L
T32
Compare/PWM
Output(s)
CCSEL
MOD<3:0>
Sync and
Gating
Sources
16/32-Bit
Timer
 2013 Microchip Technology Inc.
Output Compare/
PWM
OEFA/OEFB
Advance Information
DS33030A-page 143
PIC24FV16KM204 FAMILY
13.1
Time Base Generator
The Timer Clock Generator (TCG) generates a clock
for the module’s internal time base, using one of the
clock signals already available on the microcontroller.
This is used as the time reference for the module in its
three major modes. The internal time base is shown in
Figure 13-2.
FIGURE 13-2:
There are eight inputs available to the clock generator,
which are selected using the CLKSEL<2:0> bits
(CCPxCON1L<10:8>). The system clock is the default
source (CLKSEL<2:0> = 000). When other clock
sources are selected, clock input timing restrictions or
module operating restrictions may exist.
TIMER CLOCK GENERATOR
Clock
Sources
TMRPS<1:0>
TMRSYNC
SSDG
Prescaler
Clock
Synchronizer
Gate(1)
To Rest
of Module
CLKSEL<2:0>
Note 1:
13.2
Gating available in Timer modes only.
General Purpose Timer
13.2.1
Timer mode is selected when CCSEL = 0 and
MOD<3:0> = 0000. The timer can function as a 32-bit
timer or a dual 16-bit timer, depending on the setting of
the T32 bit (Table 13-1).
TABLE 13-1:
TIMER OPERATION MODE
T32
(CCPxCONL<5>)
Operating Mode
0
Dual Timer Mode (16-bit)
1
Timer Mode (32-bit)
Dual 16-Bit Timer mode provides a simple timer function with two independent 16-bit timer/counters. The
primary timer uses CCPxTMRL and CCPxPRL. Only
the primary timer can interact with other modules on
the device. It generates the MCCPx Out Sync signals
for use by other MCCP modules. It can also use the
SYNC<4:0> bits signal generated by other modules.
The secondary timer uses CCPxTMRH and CCPxPRH.
It is intended to be used only as a periodic interrupt
source for scheduling CPU events. It does not generate
an Output Sync/Trigger signal like the primary time base.
SYNC AND TRIGGER OPERATION
In both 16-bit and 32-bit modes, the timer can also
function in either Synchronization (“Sync”) or Trigger
operation.
Both
use
the
SYNC<4:0>
bits
(CCPxCON1H<4:0>) to determine the input signal
source. The difference is how that signal affects the
timer.
In Sync operation, the timer Reset or clear occurs when
the input selected by SYNC<4:0> is asserted. The
timer immediately begins to count again from zero
unless it is held for some other reason. Sync operation
is used whenever the TRIGEN bit (CCPxCON1H<7>)
is cleared. SYNC<4:0> can have any value except
‘11111’.
In Trigger operation, the timer is held in Reset until the
input selected by SYNC<4:0> is asserted; when it
occurs, the timer starts counting. Trigger operation is
used whenever the TRIGEN bit is set. In Trigger mode,
the timer will continue running after a Trigger event as
long as the CCPTRIG bit is set. To clear CCPTRIG, the
TRCLR bit must be set to clear the Trigger event, reset
the timer and hold it at zero until another Trigger event
occurs.
The 32-Bit Timer mode uses the CCPxTMRL and
CCPxTMRH registers, together, as a single 32-bit timer.
When CCPxTMRL overflows, CCPxTMRH increments
by one. This mode provides a simple timer function
when it is important to track long time periods. Note that
the T32 bit (CCPxCON1L<5>) should be set before the
CCPxTMRL or CCPxPRH registers are written to
initialize the 32-bit timer.
DS33030A-page 144
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 13-3:
DUAL 16-BIT TIMER MODE
CCPxPRL
Comparator
Sync/
Trigger
Control
SYNC<4:0>
CCPxTMRL
Comparator
OC Clock
Sources
Set CCTxIF
Special Event Trigger
Time Base
Generator
CCPxRB
CCPxTMRH
Comparator
Set CCPxIF
CCPxPRH
FIGURE 13-4:
32-BIT TIMER MODE
Sync/
Trigger
Control
SYNC<4:0>
OC Clock
Sources
Time Base
Generator
CCPxTMRH
CCPxTMRL
Comparator
CCPxPRH
 2013 Microchip Technology Inc.
Set CCTxIF
CCPxPRL
Advance Information
DS33030A-page 145
PIC24FV16KM204 FAMILY
13.3
pulses. Like most PIC® MCU peripherals, the output
compare module can also generate interrupts on a
compare match event
Output Compare Mode
Output Compare mode compares the Timer register
value with the value of one or two Compare registers,
depending on its mode of operation. The output compare module on compare match events has the ability
to generate a single output transition or a train of output
TABLE 13-2:
Table 13-2 shows the various modes available in
output compare modes.
OUTPUT COMPARE/PWM MODES
MOD<3:0>
T32
(CCP1CONL<3:0>) (CCP1CONL<5>)
Operating Mode
0001
0
Output High on Compare (16-bit)
0001
1
Output High on Compare (32-bit)
0010
0
Output Low on Compare (16-bit)
0010
1
Output Low on Compare (32-bit)
0011
0
Output Toggle on Compare (16-bit)
0011
1
Output Toggle on Compare (32-bit)
0100
0
Dual Edge Compare (16-bit)
Dual Edge Mode
0101
0
Dual Edge Compare (16-bit buffered)
PWM Mode
0110
0
Center-Aligned Pulse (16-bit buffered)
Center PWM
0111
0
Variable Frequency Pulse (16-bit)
0111
1
Variable Frequency Pulse (32-bit)
FIGURE 13-5:
Single-Edge Mode
OUTPUT COMPARE x BLOCK DIAGRAM
CCPxCON1H/L
CCPxCON2H/L
CCPxPRL
CCPxCON3H/L
Comparator
CCPxRA
Rollover/Reset
CCPxRA Buffer
Comparator
OC Clock
Sources
Time Base
Generator
Increment
CCPxTMRH/L
Reset
Trigger and
Sync Sources
Trigger and
Sync Logic
Match Event
Comparator
OC Output,
Auto-Shutdown
and Polarity
Match
Event
Rollover
Edge
Detect
Match
Event
CCPx Pin(s)
Control
OCFA/OCFB
Fault Logic
CCPxRB Buffer
Rollover/Reset
CCPxRB
Output Compare
Interrupt
Reset
DS33030A-page 146
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
13.4
Input Capture Mode
Input Capture mode is used to capture a timer value
from an independent timer base upon an event on an
input pin or other internal Trigger source. The input
capture features are useful in applications requiring
frequency (time period) and pulse measurement.
Figure 13-6 depicts a simplified block diagram of Input
Capture mode.
TABLE 13-3:
Input Capture mode uses a dedicated 16/32-bit, synchronous, up counting timer for the capture function. The timer
value is written to the FIFO when a capture event occurs.
The internal value may be read (with a synchronization
delay) using the CCPxTMRH/L register.
To use Input Capture mode, the CCSEL bit
(CCPxCON1L<4>) must be set. The T32 and the
MOD<3:0> bits are used to select the proper Capture
mode, as shown in Table 13-3.
INPUT CAPTURE MODES
MOD<3:0>
(CCP1CONL<3:0>)
T32
(CCP1CONL<5>)
Operating Mode
0000
0
Edge Detect (16-bit capture)
0000
1
Edge Detect (32-bit capture)
0001
0
Every Rising (16-bit capture)
0001
1
Every Rising (32-bit capture)
0010
0
Every Falling (16-bit capture)
0010
1
Every Falling (32-bit capture)
0011
0
Every Rise/Fall (16-bit capture)
0011
1
Every Rise/Fall (32-bit capture)
0100
0
Every 4th Rising (16-bit capture)
0100
1
Every 4th Rising (32-bit capture)
0101
0
Every 16th Rising (16-bit capture)
0101
1
Every 16th Rising (32-bit capture)
FIGURE 13-6:
INPUT CAPTURE x BLOCK DIAGRAM
IC<2:0>
IC Clock
Sources
Clock
Select
MOD<3:0>
OPS<3:0>
Edge Detect Logic
and
Clock Synchronizer
Event and
Interrupt
Logic
Set CCPxIF
Increment
Reset
Trigger and
Sync Sources
Trigger and
Sync Logic
16
CCPxTMRH/L
4-Level FIFO Buffer
16
T32
16
CCPxBUFx
System Bus
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 147
PIC24FV16KM204 FAMILY
13.5
Auxiliary Output
The MCCP and SCCP modules have an auxiliary (secondary) output that provides other peripherals access
to internal module signals. The auxiliary output is
intended to connect to other MCCP or SCCP modules,
or other digital peripherals, to provide these types of
functions:
The type of output signal is selected using the
AUXOUT<1:0> control bits (CCPxCON2H<4:3>). The
type of output signal is also dependent on the module
operating mode.
On the PIC24FV16KM204 family of parts, the following
modules have access to the auxiliary output signal:
• CTMU
• Time Base Synchronization
• Peripheral Trigger and Clock Inputs
• Signal Gating
TABLE 13-4:
AUXILIARY OUTPUT
AUXOUT<1:0>
CCSEL
MOD<3:0>
Comments
00
x
xxxx
Auxiliary output disabled
No Output
01
0
0000
Time Base modes
Time Base Period Reset or Rollover
Special Event Trigger Output
10
No Output
11
01
0
10
11
01
Signal Description
1
0001
through
1111
xxxx
Output Compare modes
Time Base Period Reset or Rollover
Output Compare Event Signal
Output Compare Signal
Input Capture modes
Time Base Period Reset or Rollover
10
Reflects the Value of the ICDIS bit
11
Input Capture Event Signal
DS33030A-page 148
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 13-1:
CCPxCON1L: CCPx CONTROL 1 LOW REGISTERS
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CCPON
—
CCPSIDL
CCPSLP
TMRSYNC
CLKSEL2
CLKSEL1
CLKSEL0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TMRPS1
TMRPS0
T32
CCSEL
MOD3
MOD2
MOD1
MOD0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CCPON: CCPx Module Enable bit
1 = Module is enabled with operating mode specified by the MOD<3:0> control bits
0 = Module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
CCPSIDL: CCPx Stop in Idle Mode Bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12
CCPSLP: CCPx Sleep Mode Enable bit
1 = Module continues to operate in Sleep modes
0 = Module does not operate in Sleep modes
bit 11
TMRSYNC: Time Base Clock Synchronization bit
1 = Module time base clock is synchronized to the internal system clocks; timing restrictions apply
0 = Module time base clock is not synchronized to the internal system clocks
bit 10-8
CLKSEL<2:0>: CCPx Time Base Clock Select bits
111 = External TCLKIA input
110 = External TCLKIB input
101 = CLC1
100 = System Oscillator (FOSC)
011 = LPRC (31 kHz source)
010 = Secondary Oscillator
001 = 8 MHz FRC source
000 = System clock (TCY)
bit 7-6
TMRPS<1:0>: CCPx Time Base Prescale Select bits
11 = 1:64 Prescaler
10 = 1:16 Prescaler
01 = 1:4 Prescaler
00 = 1:1 Prescaler
bit 5
T32: 32-Bit Time Base Select bit
1 = Uses 32-bit time base for timer, single-edge output compare or input capture function
0 = Uses 16-bit time base for timer, single-edge output compare or input capture function
bit 4
CCSEL: Capture/Compare Mode Select bit
1 = Input capture peripheral
0 = Output Compare/PWM/Timer peripheral (exact function is selected by the MOD<3:0> bits)
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 149
PIC24FV16KM204 FAMILY
REGISTER 13-1:
bit 3-0
CCPxCON1L: CCPx CONTROL 1 LOW REGISTERS (CONTINUED)
MOD<3:0>: CCPx Mode Select bits
For CCSEL = 1 (Input Capture modes):
1xxx = Reserved
011x = Reserved
0101 = Capture every 16th rising edge
0100 = Capture every 4th rising edge
0011 = Capture every rising and falling edge
0010 = Capture every falling edge
0001 = Capture every rising edge
0000 = Capture every rising and falling edge (Edge Detect mode)
For CCSEL = 0 (Output Compare/Timer modes):
1111 = External Input mode: pulse generator is disabled, source is selected by ICS<2:0>
1110 = Reserved
110x = Reserved
10xx = Reserved
0111 = Variable Frequency Pulse mode
0110 = Center-Aligned Pulse Compare mode, buffered
0101 = Dual Edge Compare mode, buffered
0100 = Dual Edge Compare mode
0011 = 16-Bit/32-Bit Single-Edge mode, toggle output on compare match
0010 = 16-Bit/32-Bit Single-Edge mode, drive output low on compare match
0001 = 16-Bit/32-Bit Single-Edge mode, drive output high on compare match
0000 = 16-Bit/32-Bit Timer mode, output functions are disabled
DS33030A-page 150
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 13-2:
R/W-0
CCPxCON1H: CCPx CONTROL 1 HIGH REGISTERS
R/W-0
OPSSRC(1)
(2)
RTRGEN
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
OPS3
OPS2
OPS1
OPS0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TRIGEN
ONESHOT
ALTSYNC(3)
SYNC4
SYNC3
SYNC2
SYNC1
SYNC0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
OPSSRC: Output Postscaler Source Select bit(1)
1 = Output postscaler scales module Trigger output events
0 = Output postscaler scales time base interrupt events
bit 14
RTRGEN: Retrigger Enable bit(2)
1 = Time base can be retriggered when TRIG bit = 1
0 = Time base may not be retriggered when TRIG bit = 1
bit 13-12
Unimplemented: Read as ‘0’
bit 11-8
OPS3<3:0>: CCPx Interrupt Output Postscale Select bits(3)
1111 = Interrupt every 16th time base period match
1110 = Interrupt every 15th time base period match
...
0100 = Interrupt every 5th time base period match
0011 = Interrupt every 4th time base period match or 4th input capture event
0010 = Interrupt every 3rd time base period match or 3rd input capture event
0001 = Interrupt every 2nd time base period match or 2nd input capture event
0000 = Interrupt after each time base period match or input capture event
bit 7
TRIGEN: CCPx Trigger Enable bit
1 = Trigger operation of time base is enabled
0 = Trigger operation of time base is disabled
bit 6
ONESHOT: One-Shot Mode Enable bit
1 = One-Shot Trigger mode is enabled; Trigger duration is set by OSCNT<2:0>
0 = One-Shot Trigger mode disabled
bit 5
ALTSYNC: Capture/Compare/PWMx Clock Select bits(3)
1 = An alternate signal is used as the module synchronization output signal
0 = The module synchronization output signal is the Time Base Reset/rollover event
bit 4-0
SYNC<4:0>: CCPx Synchronization Source Select bits
See Table 13-5 for the definition of inputs.
Note 1:
2:
3:
This control bit has no function in Input Capture modes.
This control bit has no function when TRIGEN = 0.
Output postscale settings from 1:5 to 1:16 (0100-1111) will result in a FIFO buffer overflow for Input Capture
modes.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 151
PIC24FV16KM204 FAMILY
TABLE 13-5:
SYNCHRONIZATION SOURCES
SYNC<4:0>
Synchronization Source
00000
None; Timer with Rollover on CCPxPR Match or FFFFh
00001
MCCP1 or SCCP1 Sync Output
00010
MCCP2 or SCCP2 Sync Output
00011
MCCP3 or SCCP3 Sync Output
00100
MCCP4 or SCCP4 Sync Output
00101
MCCP5 or SCCP5 Sync Output
0011x
Unused
01000
External Interrupt 0
01001
External Interrupt 1
01010
External Interrupt 2
01011
Timer1 Sync Output
01100 to 10000
Unused
10001
CLC1 Output
10010
CLC2 Output
10011 to 10111
Unused
11000
Comparator 1
11001
Comparator 1
11010
Comparator 1
11011
A/D
11100
CTMU
11101 and 11110
Unused
11111
DS33030A-page 152
None; Timer with Auto-Rollover (FFFFh → 0000h)
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 13-3:
CCPxCON2L: CCPx CONTROL 2 LOW REGISTERS
R/W-0
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
PWMRSEN
ASDGM
—
SSDG
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ASDG7
ASDG6
ASDG5
ASDG4
ASDG3
ASDG2
ASDG1
ASDG0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
PWMRSEN: CCPx PWM Restart Enable bit
1 = ASEVT bit clears automatically at the beginning of the next PWM period, after the shutdown input
has ended
0 = ASEVT must be cleared in software to resume PWM activity on output pins
bit 14
ASDGM: CCPx Auto-Shutdown Gate Mode Enable bit
1 = Wait until the next Time Base Reset or rollover for shutdown to occur
0 = Shutdown event occurs immediately
bit 13
Unimplemented: Read as ‘0’
bit 12
SSDG: CCPx Software Shutdown/Gate Control bit
1 = Manually force auto-shutdown, timer clock gate or input capture signal gate event (setting of
ASDGM bit still applies)
0 = Normal module operation
bit 11-8
Unimplemented: Read as ‘0’
bit 7-0
ASDG<7:0>: CCPx Auto-Shutdown/Gating Source Enable bits
1 = ASDGx Source n is enabled (See Table 13-6 for auto-shutdown/gating sources)
0 = ASDGx Source n is disabled
TABLE 13-6:
AUTO-SHUTDOWN AND GATING SOURCES
ASDGx Bits
Auto-Shutdown/Gating Source
0
Comparator 1 Output
1
Comparator 2 Output
2
Comparator 3 Output
3
SCCP4 Output Compare
4
SCCP5 Output Compare
5
CLC1 Output
6
OCFA Fault Input
7
OCFB Fault Input
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 153
PIC24FV16KM204 FAMILY
REGISTER 13-4:
R/W-0
CCPxCON2H: CCPx CONTROL 2 HIGH REGISTERS
U-0
OENSYNC
—
R/W-0
R/W-0
(1)
(1)
OCFEN
OCEEN
R/W-0
OCDEN
(1)
R/W-0
(1)
OCCEN
R/W-0
(1)
OCBEN
R/W-0
OCAEN
bit 15
bit 8
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ICGSM1
ICGSM0
—
AUXOUT1
AUXOUT0
ICS2
ICS1
ICS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
OENSYNC: Output Enable Synchronization bit
1 = Update by output enable bits occurs on the next Time Base Reset or rollover
0 = Update by output enable bits occurs immediately
bit 14
Unimplemented: Read as ‘0’
bit 13-8
OCxEN: Output Enable/Steering Control bits(1)
1 = OCx pin is controlled by the CCPx module and produces an output compare or PWM signal
0 = OCx pin is not controlled by the CCPx module; the pin is available to the port logic or another
peripheral multiplexed on the pin
bit 7-6
ICGSM<1:0>: Input Capture Gating Source Mode Control bits
11 = Reserved
10 = One-Shot mode: falling edge from gating source disables future capture events (ICDIS = 1)
01 = One-Shot mode: rising edge from gating source enables future capture events (ICDIS = 0)
00 = Level-Sensitive mode: a high level from gating source will enable future capture events; a low level
will disable future capture events
bit 5
Unimplemented: Read as ‘0’
bit 4-3
AUXOUT<1:0>: Auxiliary Output Signal on Event Selection bits
11 = Input capture or output compare event; no signal in Timer mode
10 = Signal output defined by module operating mode (see Table 13-4)
01 = Time base rollover event (all modes)
00 = Disabled
bit 2-0
ICS<2:0>: Input Capture Source Select bits
111 = Unused
110 = CLC2 output
101 = CLC1 output
100 = Unused
011 = Comparator 3 output
010 = Comparator 2 output
001 = Comparator 1 output
000 = Input Capture x (ICx) I/O pin
Note 1:
OCFEN through OCBEN (bits<13:9>) are implemented in MCCPx modules only.
DS33030A-page 154
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 13-5:
CCPxCON3L: CCPx CONTROL 3 LOW REGISTERS (1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
DT5
DT4
DT3
DT2
DT1
DT0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-6
Unimplemented: Read as ‘0’
bit 5-0
DT<5:0>: Capture/Compare/PWMx Dead-Time Select bits
111111 = Insert 63 dead-time delay periods between complementary output signals
111110 = Insert 62 dead-time delay periods between complementary output signals
...
000010 = Insert 2 dead-time delay periods between complementary output signals
000001 = Insert 1 dead-time delay period between complementary output signals
000000 = Dead-time logic is disabled
Note 1:
This register is implemented in MCCPx modules only.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 155
PIC24FV16KM204 FAMILY
REGISTER 13-6:
R/W-0
CCPxCON3H: CCPx CONTROL 3 HIGH REGISTERS
R/W-0
OETRIG
OSCNT2
R/W-0
R/W-0
OSCNT1
U-0
OSCNT0
—
R/W-0
OUTM2
R/W-0
(1)
OUTM1
R/W-0
(1)
OUTM0(1)
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
(1)
POLACE
POLBDF
PSSACE1
R/W-0
PSSACE0
R/W-0
PSSBDF1
R/W-0
(1)
PSSBDF0(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
OETRIG: Capture/Compare/PWMx Dead-Time Select bit
1 = For Triggered mode (TRIGEN = 1): module does not drive enabled output pins until triggered
0 = Normal output pin operation
bit 14-12
OSCNT<2:0>: One-Shot Event Count bits
111 = Extend one-shot event by 7 time base periods (8 time base periods total)
110 = Extend one-shot event by 6 time base periods (7 time base periods total)
101 = Extend one-shot event by 5 time base periods (6 time base periods total)
100 = Extend one-shot event by 4 time base periods (5 time base periods total)
011 = Extend one-shot event by 3 time base periods (4 time base periods total)
010 = Extend one-shot event by 2 time base periods (3 time base periods total)
001 = Extend one-shot event by 1 time base period (2 time base periods total)
000 = Do not extend one-shot Trigger event
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OUTM<2:0>: PWMx Output Mode Control bits(1)
111 = Reserved
110 = Output Scan mode
101 = Brush DC Output mode, forward
100 = Brush DC Output mode, reverse
011 = Reserved
010 = Half-Bridge Output mode
001 = Push-Pull Output mode
000 = Steerable Single Output mode
bit 7-6
Unimplemented: Read as ‘0’
bit 5
POLACE: CCPx Output Pins, OCxA, OCxC and OCxE, Polarity Control bit
1 = Output pin polarity is active-low
0 = Output pin polarity is active-high
bit 4
POLBDF: CCPx Output Pins, OCxB, OCxD and OCxF, Polarity Control bit(1)
1 = Output pin polarity is active-low
0 = Output pin polarity is active-high
bit 3-2
PSSACE<1:0>: PWMx Output Pins, OCxA, OCxC and OCxE, Shutdown State Control bits
11 = Pins are driven active when a shutdown event occurs
10 = Pins are driven inactive when a shutdown event occurs
0x = Pins are tri-stated when a shutdown event occurs
bit 1-0
PSSBDF<1:0>: PWMx Output Pins, OCxB, OCxD, and OCxF, Shutdown State Control bits(1)
11 = Pins are driven active when a shutdown event occurs
10 = Pins are driven inactive when a shutdown event occurs
0x = Pins are in a high-impedance state when a shutdown event occurs
Note 1:
These bits are implemented in MCCPx modules only.
DS33030A-page 156
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 13-7:
CCPxSTATL: CCPx STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R-0
W1-0
W1-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
CCPTRIG
TRSET
TRCLR
ASEVT
SCEVT
ICDIS
ICOV
ICBNE
bit 7
bit 0
Legend:
C = Clearable bit
R = Readable bit
W1 = Write ‘1’ only
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
CCPTRIG: CCPx Trigger Status bit
1 = Timer has been triggered and is running
0 = Timer has not been triggered and is held in Reset
bit 6
TRSET: CCPx Trigger Set Request bit
Write ‘1’ to this location to trigger the timer when TRIGEN = 1 (location always reads as ‘0’).
bit 5
TRCLR: CCPx Trigger Clear Request bit
Write ‘1’ to this location to cancel the timer Trigger when TRIGEN = 1 (location always reads as ‘0’).
bit 4
ASEVT: CCPx Auto-Shutdown Event Status/Control bit
1 = A shutdown event is in progress; CCPx outputs are in the shutdown state
0 = CCPx outputs operate normally
bit 3
SCEVT: Single Edge Compare Event Status bit
1 = A single-edge compare event has occurred
0 = A single-edge compare event has not occurred
bit 2
ICDIS: Input Capture Disable bit
1 = Event on Input Capture x pin (ICx) does not generate a capture event
0 = Event on Input Capture x pin will generate a capture event
bit 1
ICOV: Input Capture Buffer Overflow Status bit
1 = The Input Capture FIFO buffer has overflowed
0 = The Input Capture FIFO buffer has not overflowed
bit 0
ICBNE: Input Capture Buffer Status bit
1 = Input Capture buffer has data available
0 = Input Capture buffer is empty
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 157
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 158
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
14.0
Note:
MASTER SYNCHRONOUS
SERIAL PORT (MSSP)
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on MSSP,
refer to the “PIC24F Family Reference
Manual”.
The Master Synchronous Serial Port (MSSP) module is
an 8-bit serial interface, useful for communicating with
other peripheral or microcontroller devices. These
peripheral devices may be serial EEPROMs, Shift registers, display drivers, A/D Converters, etc. The MSSP
module can operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I2C™)
- Full Master mode
- Slave mode (with general address call)
14.1
I/O Pin Configuration for SPI
In SPI Master mode, the MSSP module will assert control over any pins associated with the SDOx and SCKx
outputs. This does not automatically disable other digital functions associated with the pin, and may result in
the module driving the digital I/O port inputs. To prevent
this, the MSSP module outputs must be disconnected
from their output pins while the module is in SPI Master
mode. While disabling the module temporarily may be
an option, it may not be a practical solution in all
applications.
The SDOx and SCKx outputs for the module can be
selectively disabled by using the SDOxDIS and
SCKxDIS bits in the PADCFG1 register (Register 14-10).
Setting the bit disconnects the corresponding output for a
particular module from its assigned pin.
The SPI interface supports these modes in hardware:
•
•
•
•
Master mode
Slave mode
Daisy-Chaining Operation in Slave mode
Synchronized Slave Operation
The I2C interface supports the following modes in
hardware:
• Master mode
• Multi-Master mode
• Slave mode with 10-Bit and 7-Bit Addressing and
Address Masking
• Byte NACKing
• Selectable Address and Data Hold, and Interrupt
Masking
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 159
PIC24FV16KM204 FAMILY
FIGURE 14-1:
MSSPx BLOCK DIAGRAM (SPI MODE)
Internal Data Bus
Read
Write
SSPxBUF
SDIx
SSPxSR
bit 0
SDOx
SSx
Shift Clock
SSx Control Enable
Edge
Select
2
Clock Select
SMP:CKE
2
Edge
Select
SCKx
SSPM<3:0>
4
TMR2 Output
2
(
)
Prescaler TOSC
4, 16, 64
SSPxADD<7:0>
7
Baud
Rate
Generator
Data to TXx/RXx in SSPxSR
TRIS bit
Note:
FIGURE 14-2:
Refer to the device data sheet for pin multiplexing.
SPI MASTER/SLAVE CONNECTION
SPI Master SSPM<3:0> = 00xx
SPI Slave SSPM<3:0> = 010x
SDOx
SDIx
Serial Input Buffer
(SSPxBUF)
Serial Input Buffer
(SSPxBUF)
SDIx
Shift Register
(SSPxSR)
MSb
LSb
SCKx
Serial Clock
MSb
LSb
SCKx
PROCESSOR 1
DS33030A-page 160
Shift Register
(SSPxSR)
SDOx
PROCESSOR 2
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 14-3:
MSSPx BLOCK DIAGRAM (I2C™ MODE)
Internal Data Bus
Read
Write
SSPxBUF
Shift
Clock
SCLx
SSPxSR
SDAx
MSb
LSb
Address Mask
Match Detect
Address Match
SSPxADD
Start and
Stop bit Detect
Note:
Set/Reset S, P bits
Only port I/O names are shown in this diagram. Refer to the text for a full list of multiplexed functions.
FIGURE 14-4:
MSSPx BLOCK DIAGRAM (I2C™ MASTER MODE)
Internal Data Bus
Read
Write
SSPM<3:0>
SSPxADD<6:0>
SSPxBUF
SDAx
Shift
Clock
SDAx In
SSPxSR
MSb
Baud
Rate
Generator
LSb
Start bit, Stop bit,
Acknowledge
Generate
SCLx
Clock Cntl
Start bit Detect
Stop bit Detect
Write Collision Detect Clock Arbitrate/WCOL Detect
SCLx In
(hold off clock source)
Clock Arbitration
Set/Reset S, P (SSPxSTAT), WCOL
State Counter for
Bus Collision
Set SSPxIF, BCLxIF
End of XMIT/RCV
Reset ACKSTAT, PEN
RCV Enable
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 161
PIC24FV16KM204 FAMILY
REGISTER 14-1:
SSPxSTAT: MSSPx STATUS REGISTER (SPI MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
SMP
R/W-0
R-0
R-0
R-0
R-0
R-0
R-0
(1)
D/A
P
S
R/W
UA
BF
CKE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
SMP: Sample bit
SPI Master mode:
1 = Input data is sampled at the end of data output time
0 = Input data is sampled at the middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode.
bit 6
CKE: SPI Clock Select bit(1)
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
bit 5
D/A: Data/Address bit
Used in I2C™ mode only.
bit 4
P: Stop bit
Used in I2C mode only. This bit is cleared when the MSSPx module is disabled; SSPEN is cleared.
bit 3
S: Start bit
Used in I2C mode only.
bit 2
R/W: Read/Write Information bit
Used in I2C mode only.
bit 1
UA: Update Address bit
Used in I2C mode only.
bit 0
BF: Buffer Full Status bit
1 = Receive is complete, SSPxBUF is full
0 = Receive is not complete, SSPxBUF is empty
Note 1:
Polarity of clock state is set by the CKP bit (SSPxCON1<4>).
DS33030A-page 162
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 14-2:
SSPxSTAT: MSSPx STATUS REGISTER (I2C™ MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
SMP
CKE
R-0
R-0
R-0
R-0
R-0
R-0
D/A
(1)
(1)
R/W
UA
BF
P
S
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
SMP: Slew Rate Control bit
In Master or Slave mode:
1 = Slew rate control is disabled for Standard Speed mode (100 kHz and 1 MHz)
0 = Slew rate control is enabled for High-Speed mode (400 kHz)
bit 6
CKE: SMBus Select bit
In Master or Slave mode:
1 = Enables SMBus-specific inputs
0 = Disables SMBus-specific inputs
bit 5
D/A: Data/Address bit
In Master mode:
Reserved.
In Slave mode:
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
bit 4
P: Stop bit(1)
1 = Indicates that a Stop bit has been detected last
0 = Stop bit was not detected last
bit 3
S: Start bit(1)
1 = Indicates that a Start bit has been detected last
0 = Start bit was not detected last
bit 2
R/W: Read/Write Information bit
In Slave mode:(2)
1 = Read
0 = Write
In Master mode:(3)
1 = Transmit is in progress
0 = Transmit is not in progress
bit 1
UA: Update Address bit (10-Bit Slave mode only)
1 = Indicates that the user needs to update the address in the SSPxADD register
0 = Address does not need to be updated
Note 1:
2:
3:
This bit is cleared on Reset and when SSPEN is cleared.
This bit holds the R/W bit information following the last address match. This bit is only valid from the
address match to the next Start bit, Stop bit or not ACK bit.
ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSPx is in Active mode.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 163
PIC24FV16KM204 FAMILY
REGISTER 14-2:
bit 0
SSPxSTAT: MSSPx STATUS REGISTER (I2C™ MODE) (CONTINUED)
BF: Buffer Full Status bit
In Transmit mode:
1 = Transmit is in progress, SSPxBUF is full
0 = Transmit is complete, SSPxBUF is empty
In Receive mode:
1 = SSPxBUF is full (does not include the ACK and Stop bits)
0 = SSPxBUF is empty (does not include the ACK and Stop bits)
Note 1:
2:
3:
This bit is cleared on Reset and when SSPEN is cleared.
This bit holds the R/W bit information following the last address match. This bit is only valid from the
address match to the next Start bit, Stop bit or not ACK bit.
ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSPx is in Active mode.
DS33030A-page 164
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 14-3:
SSPxCON1: MSSPx CONTROL REGISTER 1 (SPI MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
WCOL
R/W-0
R/W-0
(1)
R/W-0
(2)
SSPEN
SSPOV
CKP
R/W-0
SSPM3
(3)
R/W-0
SSPM2
(3)
R/W-0
SSPM1
(3)
R/W-0
SSPM0(3)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
WCOL: Write Collision Detect bit
1 = The SSPxBUF register is written while it is still transmitting the previous word (must be cleared in
software)
0 = No collision
bit 6
SSPOV: Master Synchronous Serial Port Receive Overflow Indicator bit(1)
SPI Slave mode:
1 = A new byte is received while the SSPxBUF register is still holding the previous data. In case of overflow, the data in SSPxSR is lost. Overflow can only occur in Slave mode. The user must read the
SSPxBUF, even if only transmitting data, to avoid setting overflow (must be cleared in software).
0 = No overflow
bit 5
SSPEN: Master Synchronous Serial Port Enable bit(2)
1 = Enables serial port and configures SCKx, SDOx, SDIx and SSx as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
bit 4
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
bit 3-0
SSPM<3:0>: Master Synchronous Serial Port Mode Select bits(3)
1010 = SPI Master mode, Clock = FOSC/(2 * ([SSPxADD] + 1))
0101 = SPI Slave mode, Clock = SCKx pin; SSx pin control is disabled, SSx can be used as an I/O pin
0100 = SPI Slave mode, Clock = SCKx pin; SSx pin control is enabled
0011 = SPI Master mode, Clock = TMR2 output/2
0010 = SPI Master mode, Clock = FOSC/32
0001 = SPI Master mode, Clock = FOSC/8
0000 = SPI Master mode, Clock = FOSC/2
Note 1:
2:
3:
In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by
writing to the SSPxBUF register.
When enabled, these pins must be properly configured as inputs or outputs.
Bit combinations not specifically listed here are either reserved or implemented in I2C™ mode only.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 165
PIC24FV16KM204 FAMILY
REGISTER 14-4:
SSPxCON1: MSSPx CONTROL REGISTER 1 (I2C™ MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
WCOL
SSPOV
SSPEN(1)
CKP
SSPM3(2)
SSPM2(2)
SSPM1(2)
SSPM0(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPxBUF register was attempted while the I2C conditions were not valid for a
transmission to be started (must be cleared in software)
0 = No collision
In Slave Transmit mode:
1 = The SSPxBUF register is written while it is still transmitting the previous word (must be cleared in
software)
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit.
bit 6
SSPOV: Master Synchronous Serial Port Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPxBUF register is still holding the previous byte (must be cleared in
software)
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode.
bit 5
SSPEN: Master Synchronous Serial Port Enable bit(1)
1 = Enables the serial port and configures the SDAx and SCLx pins as the serial port pins
0 = Disables the serial port and configures these pins as I/O port pins
bit 4
CKP: SCLx Release Control bit
In Slave mode:
1 = Releases clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode.
bit 3-0
SSPM<3:0>: Master Synchronous Serial Port Mode Select bits(2)
1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
1011 = I2C Firmware Controlled Master mode (Slave Idle)
1000 = I2C Master mode, Clock = FOSC/(2 * ([SSPxADD] + 1))(3)
0111 = I2C Slave mode, 10-bit address
0110 = I2C Slave mode, 7-bit address
Note 1:
2:
3:
When enabled, the SDAx and SCLx pins must be configured as inputs.
Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.
SSPxADD values of 0, 1 or 2 are not supported when the Baud Rate Generator is used with I2C mode.
DS33030A-page 166
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 14-5:
SSPxCON2: MSSPx CONTROL REGISTER 2 (I2C™ MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
GCEN
ACKSTAT
ACKDT(1)
ACKEN(2)
RCEN(2)
PEN(2)
RSEN(2)
SEN(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
GCEN: General Call Enable bit (Slave mode only)
1 = Enables interrupt when a general call address (0000h) is received in the SSPxSR
0 = General call address is disabled
bit 6
ACKSTAT: Acknowledge Status bit (Master Transmit mode only)
1 = Acknowledge was not received from slave
0 = Acknowledge was received from slave
bit 5
ACKDT: Acknowledge Data bit (Master Receive mode only)(1)
1 = No Acknowledge
0 = Acknowledge
bit 4
ACKEN: Acknowledge Sequence Enable bit (Master mode only)(2)
1 = Initiates Acknowledge sequence on SDAx and SCLx pins and transmits ACKDT data bit;
automatically cleared by hardware
0 = Acknowledge sequence is Idle
bit 3
RCEN: Receive Enable bit (Master Receive mode only)(2)
1 = Enables Receive mode for I2C
0 = Receive is Idle
bit 2
PEN: Stop Condition Enable bit (Master mode only)(2)
1 = Initiates Stop condition on SDAx and SCLx pins; automatically cleared by hardware
0 = Stop condition is Idle
bit 1
RSEN: Repeated Start Condition Enable bit (Master mode only)(2)
1 = Initiates Repeated Start condition on SDAx and SCLx pins; automatically cleared by hardware
0 = Repeated Start condition is Idle
bit 0
SEN: Start Condition Enable bit(2)
Master Mode:
1 = Initiates Start condition on SDAx and SCLx pins; automatically cleared by hardware
0 = Start condition is Idle
Slave Mode:
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch is enabled)
0 = Clock stretching is disabled
Note 1:
2:
The value that will be transmitted when the user initiates an Acknowledge sequence at the end of a
receive.
If the I2C module is active, these bits may not be set (no spooling) and the SSPxBUF may not be written
(or writes to the SSPxBUF are disabled).
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 167
PIC24FV16KM204 FAMILY
REGISTER 14-6:
SSPxCON3: MSSPx CONTROL REGISTER 3 (SPI MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R-0
R/W-0
ACKTIM
PCIE
R/W-0
R/W-0
(1)
SCIE
BOEN
R/W-0
R/W-0
R/W-0
R/W-0
SDAHT
SBCDE
AHEN
DHEN
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
ACKTIM: Acknowledge Time Status bit (I2C™ mode only)
Unused in SPI mode.
bit 6
PCIE: Stop Condition Interrupt Enable bit (I2C mode only)
Unused in SPI mode.
bit 5
SCIE: Start Condition Interrupt Enable bit (I2C mode only)
Unused in SPI mode.
bit 4
BOEN: Buffer Overwrite Enable bit(1)
In SPI Slave mode:
1 = SSPxBUF updates every time that a new data byte is shifted in, ignoring the BF bit
0 = If a new byte is received with the BF bit of the SSPxSTAT register already set, the SSPOV bit of
the SSPxCON1 register is set and the buffer is not updated
bit 3
SDAHT: SDAx Hold Time Selection bit (I2C mode only)
Unused in SPI mode.
bit 2
SBCDE: Slave Mode Bus Collision Detect Enable bit (I2C Slave mode only)
Unused in SPI mode.
bit 1
AHEN: Address Hold Enable bit (I2C Slave mode only)
Unused in SPI mode.
bit 0
DHEN: Data Hold Enable bit (Slave mode only)
Unused in SPI mode.
Note 1:
For daisy-chained SPI operation: Allows the user to ignore all but the last received byte. SSPOV is still set
when a new byte is received and BF = 1, but hardware continues to write the most recent byte to
SSPxBUF.
DS33030A-page 168
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 14-7:
SSPxCON3: MSSPx CONTROL REGISTER 3 (I2C™ MODE)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ACKTIM(1)
PCIE
SCIE
BOEN
SDAHT
SBCDE
AHEN
DHEN
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
ACKTIM: Acknowledge Time Status bit(1)
1 = Indicates the I2C bus is in an Acknowledge sequence, set on the 8th falling edge of the SCLx clock
0 = Not an Acknowledge sequence, cleared on the 9th rising edge of the SCLx clock
bit 6
PCIE: Stop Condition Interrupt Enable bit
1 = Enables interrupt on detection of a Stop condition
0 = Stop detection interrupts are disabled(2)
bit 5
SCIE: Start Condition Interrupt Enable bit
1 = Enables interrupt on detection of a Start or Restart conditions
0 = Start detection interrupts are disabled(2)
bit 4
BOEN: Buffer Overwrite Enable bit
I2 C Master mode:
This bit is ignored.
I2 C Slave mode:
1 = SSPxBUF is updated and an ACK is generated for a received address/data byte, ignoring the state
of the SSPOV bit only if the BF bit = 0
0 = SSPxBUF is only updated when SSPOV is clear
bit 3
SDAHT: SDAx Hold Time Selection bit
1 = Minimum of 300 ns hold time on SDAx after the falling edge of SCLx
0 = Minimum of 100 ns hold time on SDAx after the falling edge of SCLx
bit 2
SBCDE: Slave Mode Bus Collision Detect Enable bit (Slave mode only)
1 = Enables slave bus collision interrupts
0 = Slave bus collision interrupts are disabled
bit 1
AHEN: Address Hold Enable bit (Slave mode only)
1 = Following the 8th falling edge of SCLx for a matching received address byte; CKP bit of the
SSPxCON1 register will be cleared and SCLx will be held low
0 = Address holding is disabled
bit 0
DHEN: Data Hold Enable bit (Slave mode only)
1 = Following the 8th falling edge of SCLx for a received data byte; slave hardware clears the CKP bit
of the SSPxCON1 register and SCLx is held low
0 = Data holding is disabled
Note 1:
2:
This bit has no effect in Slave modes for which Start and Stop condition detection is explicitly listed as
enabled.
The ACKTIM status bit is active only when the AHEN bit or DHEN bit is set.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 169
PIC24FV16KM204 FAMILY
REGISTER 14-8:
SSPxADD: MSSPx SLAVE ADDRESS/BAUD RATE GENERATOR REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADD7
ADD6
ADD5
ADD4
ADD3
ADD2
ADD1
ADD0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7-0
ADD<7:0>: Slave Address/Baud Rate Generator Value bits
SPI Master and I2 C™ Master modes:
Reload value for Baud Rate Generator. Clock period is (([SPxADD] + 1) * 2)/FOSC.
I2 C Slave modes:
Represents 7 or 8 bits of the slave address, depending on the addressing mode used:
7-Bit mode: Address is ADD<7:1>; ADD<0> is ignored.
10-Bit LSb mode: ADD<7:0> are the Least Significant bits of the address.
10-Bit MSb mode: ADD<2:1> are the two Most Significant bits of the address; ADD<7:3> are always
‘11110’ as a specification requirement; ADD<0> is ignored.
REGISTER 14-9:
SSPxMSK: I2C™ SLAVE ADDRESS MASK REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
MSK7
MSK6
MSK5
MSK4
MSK3
MSK2
MSK1
MSK0(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
Unimplemented: Read as ‘0’
bit 7-0
MSK<7:0>: Slave Address Mask Select bits(1)
1 = Masking of corresponding bit of SSPxADD is enabled
0 = Masking of corresponding bit of SSPxADD is disabled
Note 1:
x = Bit is unknown
MSK0 is not used as a mask bit in 7-bit addressing.
DS33030A-page 170
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 14-10: PADCFG1: PAD CONFIGURATION CONTROL REGISTER
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
—
SDO2DIS(1)
SCK2DIS(1)
SDO1DIS
SCK1DIS
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11
SDO2DIS: MSSP2 SDO2 Pin Disable bit(1)
1 = The SPI output data (SDO2) of MSSP2 to the pin is disabled
0 = The SPI output data (SDO2) of MSSP2 is output to the pin
bit 10
SCK2DIS: MSSP2 SCK2 Pin Disable bit(1)
1 = The SPI clock (SCK2) of MSSP2 to the pin is disabled
0 = The SPI clock (SCK2) of MSSP2 is output to the pin
bit 9
SDO1DIS: MSSP1 SDO1 Pin Disable bit
1 = The SPI output data (SDO1) of MSSP1 to the pin is disabled
0 = The SPI output data (SDO1) of MSSP1 is output to the pin
bit 8
SCK1DIS: MSSP1 SCK1 Pin Disable bit
1 = The SPI clock (SCK1) of MSSP1 to the pin is disabled
0 = The SPI clock (SCK1) of MSSP1 is output to the pin
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
x = Bit is unknown
These bits are implemented only on PIC24FXXKM20X devices.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 171
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 172
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
15.0
Note:
UNIVERSAL ASYNCHRONOUS
RECEIVER TRANSMITTER
(UART)
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on the Universal Asynchronous Receiver Transmitter,
refer to the “PIC24F Family Reference
Manual”, Section 21. “UART” (DS39708).
The Universal Asynchronous Receiver Transmitter
(UART) module is one of the serial I/O modules
available in this PIC24F device family. The UART is a
full-duplex, asynchronous system that can communicate
with peripheral devices, such as personal computers,
LIN/J2602, RS-232 and RS-485 interfaces. This module
also supports a hardware flow control option with the
UxCTS and UxRTS pins, and also includes an IrDA®
encoder and decoder.
The primary features of the UART module are:
• Full-Duplex, 8-Bit or 9-Bit Data Transmission
through the UxTX and UxRX Pins
• Even, Odd or No Parity Options (for 8-bit data)
• One or Two Stop bits
• Hardware Flow Control Option with UxCTS and
UxRTS Pins
• Fully Integrated Baud Rate Generator (IBRG) with
16-Bit Prescaler
FIGURE 15-1:
• Baud Rates Ranging from 1 Mbps to 15 bps at
16 MIPS
• 4-Deep, First-In-First-Out (FIFO) Transmit Data
Buffer
• 4-Deep FIFO Receive Data Buffer
• Parity, Framing and Buffer Overrun Error
Detection
• Support for 9-Bit mode with Address Detect
(9th bit = 1)
• Transmit and Receive Interrupts
• Loopback mode for Diagnostic Support
• Support for Sync and Break Characters
• Supports Automatic Baud Rate Detection
• IrDA® Encoder and Decoder Logic
• 16x Baud Clock Output for IrDA Support
A simplified block diagram of the UARTx module is
shown in Figure 15-1. The UARTx module consists of
these important hardware elements:
• Baud Rate Generator
• Asynchronous Transmitter
• Asynchronous Receiver
Note:
Throughout this section, references to
register and bit names that may be associated with a specific USART module are
referred to generically by the use of ‘x’ in
place of the specific module number.
Thus, “UxSTA” might refer to the USART
Status register for either USART1 or
USART2.
UARTx MODULE SIMPLIFIED BLOCK DIAGRAM
Baud Rate Generator
IrDA®
UxBCLK
Hardware Flow Control
UxRTS
UxCTS
UARTx Receiver
UxRX
UARTx Transmitter
UxTX
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 173
PIC24FV16KM204 FAMILY
15.1
UARTx Baud Rate Generator
(BRG)
The UARTx module includes a dedicated 16-bit Baud
Rate Generator (BRG). The UxBRG register controls
the period of a free-running, 16-bit timer. Equation 15-1
provides the formula for computation of the baud rate
with BRGH = 0.
EQUATION 15-1:
Baud Rate =
UxBRG =
Note 1:
EQUATION 15-2:
Baud Rate =
FCY
16 • (UxBRG + 1)
UxBRG =
FCY
–1
16 • Baud Rate
Note 1:
Example 15-1 provides the calculation of the baud rate
error for the following conditions:
• FCY = 4 MHz
• Desired Baud Rate = 9600
Desired Baud Rate
Equation 15-2 shows the formula for computation of
the baud rate with BRGH = 1.
UARTx BAUD RATE WITH
BRGH = 0(1)
Based on FCY = FOSC/2; Doze mode
and PLL are disabled.
EXAMPLE 15-1:
The maximum baud rate (BRGH = 0) possible is
FCY/16 (for UxBRG = 0) and the minimum baud rate
possible is FCY/(16 * 65536).
UARTx BAUD RATE WITH
BRGH = 1(1)
FCY
4 • (UxBRG + 1)
FCY
4 • Baud Rate
–1
Based on FCY = FOSC/2; Doze mode
and PLL are disabled.
The maximum baud rate (BRGH = 1) possible is FCY/4
(for UxBRG = 0) and the minimum baud rate possible
is FCY/(4 * 65536).
Writing a new value to the UxBRG register causes the
BRG timer to be reset (cleared). This ensures the BRG
does not wait for a timer overflow before generating the
new baud rate.
BAUD RATE ERROR CALCULATION (BRGH = 0)(1)
= FCY/(16 (UxBRG + 1))
Solving for UxBRG value:
UxBRG
UxBRG
UxBRG
= ((FCY/Desired Baud Rate)/16) – 1
= ((4000000/9600)/16) – 1
= 25
Calculated Baud Rate = 4000000/(16 (25 + 1))
= 9615
Error
Note 1:
= (Calculated Baud Rate – Desired Baud Rate)
Desired Baud Rate
= (9615 – 9600)/9600
= 0.16%
Based on FCY = FOSC/2; Doze mode and PLL are disabled.
DS33030A-page 174
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
15.2
1.
2.
3.
4.
5.
6.
Set up the UARTx:
a) Write the appropriate values for data, parity
and Stop bits.
b) Write the appropriate baud rate value to the
UxBRG register.
c) Set up transmit and receive interrupt enable
and priority bits.
Enable the UARTx.
Set the UTXEN bit (causes a transmit interrupt,
two cycles after being set).
Write the data byte to the lower byte of the
UxTXREG word. The value will be immediately
transferred to the Transmit Shift Register (TSR)
and the serial bit stream will start shifting out
with the next rising edge of the baud clock.
Alternately, the data byte may be transferred
while UTXEN = 0, and then, the user may set
UTXEN. This will cause the serial bit stream to
begin immediately, because the baud clock will
start from a cleared state.
A transmit interrupt will be generated as per
interrupt control bit, UTXISELx.
15.3
1.
2.
3.
4.
5.
6.
Transmitting in 8-Bit Data Mode
Transmitting in 9-Bit Data Mode
Set up the UARTx (as described in Section 15.2
“Transmitting in 8-Bit Data Mode”).
Enable the UARTx.
Set the UTXEN bit (causes a transmit interrupt,
two cycles after being set).
Write UxTXREG as a 16-bit value only.
A word write to UxTXREG triggers the transfer
of the 9-bit data to the TSR. The serial bit stream
will start shifting out with the first rising edge of
the baud clock.
A transmit interrupt will be generated as per the
setting of control bit, UTXISELx.
15.4
Break and Sync Transmit
Sequence
The following sequence will send a message frame
header, made up of a Break, followed by an Auto-Baud
Sync byte.
1.
2.
3.
4.
5.
Configure the UARTx for the desired mode.
Set UTXEN and UTXBRK – this sets up the
Break character.
Load the UxTXREG with a dummy character to
initiate transmission (value is ignored).
Write ‘55h’ to UxTXREG – loads the Sync
character into the transmit FIFO.
After the Break has been sent, the UTXBRK bit
is reset by hardware. The Sync character now
transmits.
 2013 Microchip Technology Inc.
15.5
1.
2.
3.
4.
5.
Receiving in 8-Bit or 9-Bit Data
Mode
Set up the UARTx (as described in Section 15.2
“Transmitting in 8-Bit Data Mode”).
Enable the UARTx.
A receive interrupt will be generated when one
or more data characters have been received, as
per interrupt control bit, URXISELx.
Read the OERR bit to determine if an overrun
error has occurred. The OERR bit must be reset
in software.
Read UxRXREG.
The act of reading the UxRXREG character will move
the next character to the top of the receive FIFO,
including a new set of PERR and FERR values.
15.6
Operation of UxCTS and UxRTS
Control Pins
UARTx Clear-to-Send (UxCTS) and Request-to-Send
(UxRTS) are the two hardware controlled pins that are
associated with the UARTx module. These two pins
allow the UARTx to operate in Simplex and Flow Control modes. They are implemented to control the
transmission and reception between the Data Terminal
Equipment (DTE). The UEN<1:0> bits in the UxMODE
register configure these pins.
15.7
Infrared Support
The UARTx module provides two types of infrared
UARTx support: one is the IrDA clock output to support
an external IrDA encoder and decoder device (legacy
module support), and the other is the full implementation
of the IrDA encoder and decoder.
As the IrDA modes require a 16x baud clock, they will
only work when the BRGH bit (UxMODE<3>) is ‘0’.
15.7.1
EXTERNAL IrDA SUPPORT – IrDA
CLOCK OUTPUT
To support external IrDA encoder and decoder devices,
the UxBCLK pin (same as the UxRTS pin) can be
configured to generate the 16x baud clock. When
UEN<1:0> = 11, the UxBCLK pin will output the 16x
baud clock if the UARTx module is enabled; it can be
used to support the IrDA codec chip.
15.7.2
BUILT-IN IrDA ENCODER AND
DECODER
The UARTx has full implementation of the IrDA
encoder and decoder as part of the UARTx module.
The built-in IrDA encoder and decoder functionality is
enabled using the IREN bit (UxMODE<12>). When
enabled (IREN = 1), the receive pin (UxRX) acts as the
input from the infrared receiver. The transmit pin
(UxTX) acts as the output to the infrared transmitter.
Advance Information
DS33030A-page 175
PIC24FV16KM204 FAMILY
REGISTER 15-1:
R/W-0
UxMODE: UARTx MODE REGISTER
U-0
UARTEN
—
R/W-0
R/W-0
U-0
R/W-0(2)
R/W-0(2)
RTSMD
—
UEN1
UEN0
R/W-0
USIDL
IREN
(1)
bit 15
bit 8
R/C-0, HC
R/W-0
R/W-0, HC
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
WAKE
LPBACK
ABAUD
URXINV
BRGH
PDSEL1
PDSEL0
STSEL
bit 7
bit 0
Legend:
C = Clearable bit
HC = Hardware Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
UARTEN: UARTx Enable bit
1 = UARTx is enabled; all UARTx pins are controlled by UARTx, as defined by UEN<1:0>
0 = UARTx is disabled; all UARTx pins are controlled by port latches, UARTx power consumption is
minimal
bit 14
Unimplemented: Read as ‘0’
bit 13
USIDL: UARTx Stop in Idle Mode bit
1 = Discontinues module operation when the device enters Idle mode
0 = Continues module operation in Idle mode
bit 12
IREN: IrDA® Encoder and Decoder Enable bit(1)
1 = IrDA encoder and decoder are enabled
0 = IrDA encoder and decoder are disabled
bit 11
RTSMD: Mode Selection for UxRTS Pin bit
1 = UxRTS pin is in Simplex mode
0 = UxRTS pin is in Flow Control mode
bit 10
Unimplemented: Read as ‘0’
bit 9-8
UEN<1:0>: UARTx Enable bits(2)
11 = UxTX, UxRX and UxBCLK pins are enabled and used; UxCTS pin is controlled by port latches
10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used
01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin is controlled by port latches
00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/UxBCLK pins are controlled by port
latches
bit 7
WAKE: Wake-up on Start Bit Detect During Sleep Mode Enable bit
1 = UARTx will continue to sample the UxRX pin; interrupt is generated on the falling edge, bit is
cleared in hardware on the following rising edge
0 = No wake-up is enabled
bit 6
LPBACK: UARTx Loopback Mode Select bit
1 = Enables Loopback mode
0 = Loopback mode is disabled
bit 5
ABAUD: Auto-Baud Enable bit
1 = Enables baud rate measurement on the next character – requires reception of a Sync field (55h);
cleared in hardware upon completion
0 = Baud rate measurement is disabled or completed
bit 4
URXINV: UARTx Receive Polarity Inversion bit
1 = UxRX Idle state is ‘0’
0 = UxRX Idle state is ‘1’
Note 1:
2:
This feature is is only available for the 16x BRG mode (BRGH = 0).
The bit availability depends on the pin availability.
DS33030A-page 176
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 15-1:
UxMODE: UARTx MODE REGISTER (CONTINUED)
bit 3
BRGH: High Baud Rate Enable bit
1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode)
0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode)
bit 2-1
PDSEL<1:0>: Parity and Data Selection bits
11 = 9-bit data, no parity
10 = 8-bit data, odd parity
01 = 8-bit data, even parity
00 = 8-bit data, no parity
bit 0
STSEL: Stop Bit Selection bit
1 = Two Stop bits
0 = One Stop bit
Note 1:
2:
This feature is is only available for the 16x BRG mode (BRGH = 0).
The bit availability depends on the pin availability.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 177
PIC24FV16KM204 FAMILY
REGISTER 15-2:
UxSTA: UARTx STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
R/W-0, HC
R/W-0
R-0, HSC
R-1, HSC
UTXISEL1
UTXINV
UTXISEL0
—
UTXBRK
UTXEN
UTXBF
TRMT
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R-1, HSC
R-0, HSC
R-0, HSC
R/C-0, HS
R-0, HSC
URXISEL1
URXISEL0
ADDEN
RIDLE
PERR
FERR
OERR
URXDA
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
HS = Hardware Settable bit
C = Clearable bit
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15,13
UTXISEL<1:0>: UARTx Transmission Interrupt Mode Selection bits
11 = Reserved; do not use
10 = Interrupt when a character is transferred to the Transmit Shift Register (TSR) and as a result, the
transmit buffer becomes empty
01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit operations
are completed
00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at least
one character open in the transmit buffer)
bit 14
UTXINV: IrDA® Encoder Transmit Polarity Inversion bit
If IREN = 0:
1 = UxTX Idle ‘0’
0 = UxTX Idle ‘1’
If IREN = 1:
1 = UxTX Idle ‘1’
0 = UxTX Idle ‘0’
bit 12
Unimplemented: Read as ‘0’
bit 11
UTXBRK: UARTx Transmit Break bit
1 = Sends Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;
cleared by hardware upon completion
0 = Sync Break transmission is disabled or completed
bit 10
UTXEN: UARTx Transmit Enable bit
1 = Transmit is enabled; UxTX pin is controlled by UARTx
0 = Transmit is disabled; any pending transmission is aborted and the buffer is reset; UxTX pin is
controlled by the PORT register
bit 9
UTXBF: UARTx Transmit Buffer Full Status bit (read-only)
1 = Transmit buffer is full
0 = Transmit buffer is not full, at least one more character can be written
bit 8
TRMT: Transmit Shift Register Empty bit (read-only)
1 = Transmit Shift Register is empty and the transmit buffer is empty (the last transmission has
completed)
0 = Transmit Shift Register is not empty; a transmission is in progress or queued
bit 7-6
URXISEL<1:0>: UARTx Receive Interrupt Mode Selection bits
11 = Interrupt is set on an RSR transfer, making the receive buffer full (i.e., has 4 data characters)
10 = Interrupt is set on an RSR transfer, making the receive buffer 3/4 full (i.e., has 3 data characters)
0x = Interrupt is set when any character is received and transferred from the RSR to the receive buffer;
receive buffer has one or more characters
DS33030A-page 178
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 15-2:
UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED)
bit 5
ADDEN: Address Character Detect bit (bit 8 of received data = 1)
1 = Address Detect mode is enabled; if 9-bit mode is not selected, this does not take effect
0 = Address Detect mode is disabled
bit 4
RIDLE: Receiver Idle bit (read-only)
1 = Receiver is Idle
0 = Receiver is active
bit 3
PERR: Parity Error Status bit (read-only)
1 = Parity error has been detected for the current character (character at the top of the receive FIFO)
0 = Parity error has not been detected
bit 2
FERR: Framing Error Status bit (read-only)
1 = Framing error has been detected for the current character (character at the top of the receive FIFO)
0 = Framing error has not been detected
bit 1
OERR: Receive Buffer Overrun Error Status bit (clear/read-only)
1 = Receive buffer has overflowed
0 = Receive buffer has not overflowed (clearing a previously set OERR bit (1  0 transition) will reset
the receiver buffer and the RSR to the empty state)
bit 0
URXDA: UARTx Receive Buffer Data Available bit (read-only)
1 = Receive buffer has data; at least one more characters can be read
0 = Receive buffer is empty
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 179
PIC24FV16KM204 FAMILY
REGISTER 15-3:
UxTXREG: UARTx TRANSMIT REGISTER
U-x
U-x
U-x
U-x
U-x
U-x
U-x
W-x
—
—
—
—
—
—
—
UTX8
bit 15
bit 8
W-x
W-x
W-x
W-x
W-x
W-x
W-x
W-x
UTX7
UTX6
UTX5
UTX4
UTX3
UTX2
UTX1
UTX0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-9
Unimplemented: Read as ‘0’
bit 8
UTX8: Data of the Transmitted Character bit (in 9-bit mode)
bit 7-0
UTX<7:0>: Data of the Transmitted Character bits
REGISTER 15-4:
x = Bit is unknown
UxRXREG: UARTx RECEIVE REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R-0, HSC
—
—
—
—
—
—
—
URX8
bit 15
bit 8
R-0, HSC
R-0, HSC
R-0, HSC
R-0, HSC
R-0, HSC
R-0, HSC
R-0, HSC
R-0, HSC
URX7
URX6
URX5
URX4
URX3
URX2
URX1
URX0
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-9
Unimplemented: Read as ‘0’
bit 8
URX8: Data of the Received Character bit (in 9-bit mode)
bit 7-0
URX<7:0>: Data of the Received Character bits
DS33030A-page 180
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
16.0
Note:
REAL-TIME CLOCK AND
CALENDAR (RTCC)
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on the
Real-Time Clock and Calendar, refer to the
“PIC24F Family Reference Manual”,
Section 29. “Real-Time Clock and
Calendar (RTCC)” (DS39696).
The RTCC provides the user with a Real-Time Clock
and Calendar (RTCC) function that can be calibrated.
Key features of the RTCC module are:
• Operates in Sleep and Retention Sleep modes
• Selectable clock source
• Provides hours, minutes and seconds using
24-hour format
• Visibility of one half second period
• Provides calendar – weekday, date, month and
year
• Alarm-configurable for half a second, one second,
10 seconds, one minute, 10 minutes, one hour,
one day, one week, one month or one year
• Alarm repeat with decrementing counter
• Alarm with indefinite repeat chime
• Year 2000 to 2099 leap year correction
FIGURE 16-1:
16.1
RTCC Source Clock
The user can select between the SOSC crystal
oscillator, LPRC internal oscillator or an external
50 Hz/60 Hz power line input as the clock reference for
the RTCC module. This gives the user an option to trade
off system cost, accuracy and power consumption,
based on the overall system needs.
RTCC BLOCK DIAGRAM
CPU Clock Domain
RTCC Clock Domain
Input from
SOSC/LPRC
Oscillator or
External Source
• BCD format for smaller software overhead
• Optimized for long term battery operation
• User calibration of the 32.768 kHz clock
crystal/32K INTRC frequency with periodic
auto-adjust
• Optimized for long term battery operation
• Fractional second synchronization
• Calibration to within ±2.64 seconds error per
month
• Calibrates up to 260 ppm of crystal error
• Ability to periodically wake-up external devices
without CPU intervention (external power control)
• Power control output for external circuit control
• Calibration takes effect every 15 seconds
• Runs from any one of the following:
- External Real-Time Clock of 32.768 kHz
- Internal 31.25 kHz LPRC Clock
- 50 Hz or 60 Hz External Input
RCFGCAL
RTCC Prescalers
ALCFGRPT
RTCVAL
YEAR
MTHDY
WKDYHR
MINSEC
ALRMVAL
ALMTHDY
ALWDHR
ALMINSEC
0.5 Sec
RTCC Timer
Alarm
Event
Comparator
Alarm Registers with Masks
Repeat Counter
RTCOUT<1:0>
RTCC
Interrupt
RTCC Interrupt Logic
1s
Alarm Pulse
Clock Source
RTCC
Pin
RTCOE
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 181
PIC24FV16KM204 FAMILY
16.2
RTCC Module Registers
TABLE 16-2:
The RTCC module registers are organized into three
categories:
• RTCC Control Registers
• RTCC Value Registers
• Alarm Value Registers
16.2.1
REGISTER MAPPING
To limit the register interface, the RTCC Timer and
Alarm Time registers are accessed through corresponding register pointers. The RTCC Value register
window (RTCVALH and RTCVALL) uses the RTCPTRx
bits (RCFGCAL<9:8>) to select the desired Timer
register pair (see Table 16-1).
By writing the RTCVALH byte, the RTCC Pointer value,
the RTCPTR<1:0> bits decrement by one until they reach
‘00’. Once they reach ‘00’, the MINUTES and SECONDS
value will be accessible through RTCVALH and
RTCVALL until the pointer value is manually changed.
TABLE 16-1:
RTCPTR<1:0>
RTCVAL REGISTER MAPPING
RTCC Value Register Window
RTCVAL<15:8>
RTCVAL<7:0>
00
MINUTES
SECONDS
01
WEEKDAY
HOURS
10
MONTH
DAY
11
—
YEAR
EXAMPLE 16-1:
push
push
disi
mov
mov
mov
mov
bset
pop
pop
ALRMVALH<15:8>
ALRMVALL<7:0>
00
01
ALRMMIN
ALRMWD
ALRMSEC
ALRMHR
10
11
ALRMMNTH
PWCSTAB
ALRMDAY
PWCSAMP
Considering that the 16-bit core does not distinguish
between 8-bit and 16-bit read operations, the user must
be aware that when reading either the ALRMVALH or
ALRMVALL bytes, the ALRMPTR<1:0> value will be
decremented. The same applies to the RTCVALH or
RTCVALL bytes with the RTCPTR<1:0> being
decremented.
Note:
16.2.2
This only applies to read operations and
not write operations.
WRITE LOCK
In order to perform a write to any of the RTCC Timer
registers, the RTCWREN bit (RCFGCAL<13>) must be
set (see Example 16-1 and Example 16-2).
Note:
16.2.3
To avoid accidental writes to the timer, it is
recommended that the RTCWREN bit
(RCFGCAL<13>) is kept clear at any
other time. For the RTCWREN bit to be
set, there is only one instruction cycle time
window allowed between the 55h/AA
sequence and the setting of RTCWREN.
Therefore, it is recommended that code
follow the procedure in Example 16-2.
SELECTING RTCC CLOCK SOURCE
There are four reference source clock options that can
be selected for the RTCC using the RTCCLK<1:0>
bits (RTCPWC<11:10>): 00 = Secondary Oscillator,
01 = LPRC, 10 = 50 Hz External Clock and 11 = 60 Hz
External Clock.
SETTING THE RTCWREN BIT IN ASSEMBLY
w7
w8
#5
#0x55, w7
w7, NVMKEY
#0xAA, w8
w8, NVMKEY
RCFGCAL, #13
w8
w7
EXAMPLE 16-2:
Alarm Value Register Window
ALRMPTR
<1:0>
The Alarm Value register window (ALRMVALH and
ALRMVALL)
uses
the
ALRMPTRx
bits
(ALCFGRPT<9:8>) to select the desired Alarm
register pair (see Table 16-2).
By writing the ALRMVALH byte, the ALRMPTR<1:0>
bits (Alarm Pointer value) decrement by one until they
reach ‘00’. Once they reach ‘00’, the ALRMMIN and
ALRMSEC value will be accessible through
ALRMVALH and ALRMVALL, until the pointer value is
manually changed.
ALRMVAL REGISTER
MAPPING
; Store W7 and W8 values on the stack.
; Disable interrupts until sequence is complete.
; Write 0x55 unlock value to NVMKEY.
; Write 0xAA unlock value to NVMKEY.
; Set the RTCWREN bit.
; Restore the original W register values from the stack.
SETTING THE RTCWREN BIT IN ‘C’
//This builtin function executes implements the unlock sequence and sets
//the RTCWREN bit.
__builtin_write_RTCWEN();
DS33030A-page 182
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
16.2.4
RTCC CONTROL REGISTERS
REGISTER 16-1: RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER(1)
R/W-0
U-0
R/W-0
R-0, HSC
R-0, HSC
R/W-0
R/W-0
R/W-0
RTCEN(2)
—
RTCWREN
RTCSYNC
HALFSEC(3)
RTCOE
RTCPTR1
RTCPTR0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
RTCEN: RTCC Enable bit(2)
1 = RTCC module is enabled
0 = RTCC module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
RTCWREN: RTCC Value Registers Write Enable bit
1 = RTCVALH and RTCVALL registers can be written to by the user
0 = RTCVALH and RTCVALL registers are locked out from being written to by the user
bit 12
RTCSYNC: RTCC Value Registers Read Synchronization bit
1 = RTCVALH, RTCVALL and ALCFGRPT registers can change while reading due to a rollover ripple
resulting in an invalid data read. If the register is read twice and results in the same data, the data
can be assumed to be valid.
0 = RTCVALH, RTCVALL or ALCFGRPT registers can be read without concern over a rollover ripple
bit 11
HALFSEC: Half Second Status bit(3)
1 = Second half period of a second
0 = First half period of a second
bit 10
RTCOE: RTCC Output Enable bit
1 = RTCC output is enabled
0 = RTCC output is disabled
bit 9-8
RTCPTR<1:0>: RTCC Value Register Window Pointer bits
Points to the corresponding RTCC Value registers when reading the RTCVALH and RTCVALL registers.
The RTCPTR<1:0> value decrements on every read or write of RTCVALH until it reaches ‘00’.
RTCVAL<15:8>:
00 = MINUTES
01 = WEEKDAY
10 = MONTH
11 = Reserved
RTCVAL<7:0>:
00 = SECONDS
01 = HOURS
10 = DAY
11 = YEAR
Note 1:
2:
3:
The RCFGCAL register is only affected by a POR.
A write to the RTCEN bit is only allowed when RTCWREN = 1.
This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 183
PIC24FV16KM204 FAMILY
REGISTER 16-1: RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER(1) (CONTINUED)
bit 7-0
Note 1:
2:
3:
CAL<7:0>: RTC Drift Calibration bits
01111111 = Maximum positive adjustment; adds 508 RTC clock pulses every one minute
.
.
.
00000001 = Minimum positive adjustment; adds 4 RTC clock pulses every one minute
00000000 = No adjustment
11111111 = Minimum negative adjustment; subtracts 4 RTC clock pulses every one minute
.
.
.
10000000 = Maximum negative adjustment; subtracts 512 RTC clock pulses every one minute
The RCFGCAL register is only affected by a POR.
A write to the RTCEN bit is only allowed when RTCWREN = 1.
This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register.
DS33030A-page 184
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 16-2:
RTCPWC: RTCC CONFIGURATION REGISTER 2(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PWCEN
PWCPOL
PWCCPRE
PWCSPRE
RTCCLK1(2)
RTCCLK0(2)
RTCOUT1
RTCOUT0
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
PWCEN: Power Control Enable bit
1 = Power control is enabled
0 = Power control is disabled
bit 14
PWCPOL: Power Control Polarity bit
1 = Power control output is active-high
0 = Power control output is active-low
bit 13
PWCCPRE: Power Control/Stability Prescaler bits
1 = PWC stability window clock is divide-by-2 of source RTCC clock
0 = PWC stability window clock is divide-by-1 of source RTCC clock
bit 12
PWCSPRE: Power Control Sample Prescaler bits
1 = PWC sample window clock is divide-by-2 of source RTCC clock
0 = PWC sample window clock is divide-by-1 of source RTCC clock
bit 11-10
RTCCLK<1:0>: RTCC Clock Select bits(2)
Determines the source of the internal RTCC clock, which is used for all RTCC timer operations.
00 = External Secondary Oscillator (SOSC)
01 = Internal LPRC Oscillator
10 = External power line source – 50 Hz
11 = External power line source – 60 Hz
bit 9-8
RTCOUT<1:0>: RTCC Output Select bits
Determines the source of the RTCC pin output.
00 = RTCC alarm pulse
01 = RTCC seconds clock
10 = RTCC clock
11 = Power control
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
2:
The RTCPWC register is only affected by a POR.
When a new value is written to these register bits, the Seconds Value register should also be written to
properly reset the clock prescalers in the RTCC.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 185
PIC24FV16KM204 FAMILY
REGISTER 16-3:
ALCFGRPT: ALARM CONFIGURATION REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ALRMEN
CHIME
AMASK3
AMASK2
AMASK1
AMASK0
ALRMPTR1
ALRMPTR0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ARPT7
ARPT6
ARPT5
ARPT4
ARPT3
ARPT2
ARPT1
ARPT0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ALRMEN: Alarm Enable bit
1 = Alarm is enabled (cleared automatically after an alarm event whenever ARPT<7:0> = 00h and
CHIME = 0)
0 = Alarm is disabled
bit 14
CHIME: Chime Enable bit
1 = Chime is enabled; ARPT<7:0> bits are allowed to roll over from 00h to FFh
0 = Chime is disabled; ARPT<7:0> bits stop once they reach 00h
bit 13-10
AMASK<3:0>: Alarm Mask Configuration bits
0000 = Every half second
0001 = Every second
0010 = Every 10 seconds
0011 = Every minute
0100 = Every 10 minutes
0101 = Every hour
0110 = Once a day
0111 = Once a week
1000 = Once a month
1001 = Once a year (except when configured for February 29th, once every 4 years)
101x = Reserved – do not use
11xx = Reserved – do not use
bit 9-8
ALRMPTR<1:0>: Alarm Value Register Window Pointer bits
Points to the corresponding Alarm Value registers when reading the ALRMVALH and ALRMVALL registers.
The ALRMPTR<1:0> value decrements on every read or write of ALRMVALH until it reaches ‘00’.
ALRMVAL<15:8>:
00 = ALRMMIN
01 = ALRMWD
10 = ALRMMNTH
11 = Unimplemented
ALRMVAL<7:0>:
00 = ALRMSEC
01 = ALRMHR
10 = ALRMDAY
11 = Unimplemented
bit 7-0
ARPT<7:0>: Alarm Repeat Counter Value bits
11111111 = Alarm will repeat 255 more times
.
.
.
00000000 = Alarm will not repeat
The counter decrements on any alarm event; it is prevented from rolling over from 00h to FFh unless
CHIME = 1.
DS33030A-page 186
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
16.2.5
RTCVAL REGISTER MAPPINGS
REGISTER 16-4:
YEAR: YEAR VALUE REGISTER(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
YRTEN3
YRTEN2
YRTEN1
YRTEN0
YRONE3
YRONE2
YRONE1
YRONE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7-4
YRTEN<3:0>: Binary Coded Decimal Value of Year’s Tens Digit bits
Contains a value from 0 to 9.
bit 3-0
YRONE<3:0>: Binary Coded Decimal Value of Year’s Ones Digit bits
Contains a value from 0 to 9.
Note 1:
A write to the YEAR register is only allowed when RTCWREN = 1.
REGISTER 16-5:
MTHDY: MONTH AND DAY VALUE REGISTER(1)
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
MTHTEN0
MTHONE3
MTHONE2
MTHONE1
MTHONE0
bit 15
bit 8
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
DAYTEN1
DAYTEN0
DAYONE3
DAYONE2
DAYONE1
DAYONE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-13
Unimplemented: Read as ‘0’
bit 12
MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit
Contains a value of ‘0’ or ‘1’.
bit 11-8
MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits
Contains a value from 0 to 9.
bit 7-6
Unimplemented: Read as ‘0’
bit 5-4
DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits
Contains a value from 0 to 3.
bit 3-0
DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits
Contains a value from 0 to 9.
Note 1:
x = Bit is unknown
A write to this register is only allowed when RTCWREN = 1.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 187
PIC24FV16KM204 FAMILY
REGISTER 16-6:
WKDYHR: WEEKDAY AND HOURS VALUE REGISTER(1)
U-0
U-0
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
—
—
—
—
—
WDAY2
WDAY1
WDAY0
bit 15
bit 8
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
HRTEN1
HRTEN0
HRONE3
HRONE2
HRONE1
HRONE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits
Contains a value from 0 to 6.
bit 7-6
Unimplemented: Read as ‘0’
bit 5-4
HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits
Contains a value from 0 to 2.
bit 3-0
HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits
Contains a value from 0 to 9.
Note 1:
A write to this register is only allowed when RTCWREN = 1.
REGISTER 16-7:
MINSEC: MINUTES AND SECONDS VALUE REGISTER
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
MINTEN2
MINTEN1
MINTEN0
MINONE3
MINONE2
MINONE1
MINONE0
bit 15
bit 8
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
SECTEN2
SECTEN1
SECTEN0
SECONE3
SECONE2
SECONE1
SECONE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits
Contains a value from 0 to 5.
bit 11-8
MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits
Contains a value from 0 to 9.
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits
Contains a value from 0 to 5.
bit 3-0
SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits
Contains a value from 0 to 9.
DS33030A-page 188
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
16.2.6
ALRMVAL REGISTER MAPPINGS
REGISTER 16-8:
ALMTHDY: ALARM MONTH AND DAY VALUE REGISTER(1)
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
MTHTEN0
MTHONE3
MTHONE2
MTHONE1
MTHONE0
bit 15
bit 8
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
DAYTEN1
DAYTEN0
DAYONE3
DAYONE2
DAYONE1
DAYONE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-13
Unimplemented: Read as ‘0’
bit 12
MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit
Contains a value of ‘0’ or ‘1’.
bit 11-8
MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits
Contains a value from 0 to 9.
bit 7-6
Unimplemented: Read as ‘0’
bit 5-4
DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits
Contains a value from 0 to 3.
bit 3-0
DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits
Contains a value from 0 to 9.
Note 1:
x = Bit is unknown
A write to this register is only allowed when RTCWREN = 1.
REGISTER 16-9:
ALWDHR: ALARM WEEKDAY AND HOURS VALUE REGISTER(1)
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
R/W-x
WDAY2
R/W-x
WDAY1
R/W-x
WDAY0
bit 8
U-0
—
U-0
—
R/W-x
HRTEN1
R/W-x
HRTEN0
R/W-x
HRONE3
R/W-x
HRONE2
R/W-x
HRONE1
R/W-x
HRONE0
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-11
bit 10-8
bit 7-6
bit 5-4
bit 3-0
Note 1:
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits
Contains a value from 0 to 6.
Unimplemented: Read as ‘0’
HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits
Contains a value from 0 to 2.
HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits
Contains a value from 0 to 9.
A write to this register is only allowed when RTCWREN = 1.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 189
PIC24FV16KM204 FAMILY
REGISTER 16-10: ALMINSEC: ALARM MINUTES AND SECONDS VALUE REGISTER
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
MINTEN2
MINTEN1
MINTEN0
MINONE3
MINONE2
MINONE1
MINONE0
bit 15
bit 8
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
SECTEN2
SECTEN1
SECTEN0
SECONE3
SECONE2
SECONE1
SECONE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits
Contains a value from 0 to 5.
bit 11-8
MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits
Contains a value from 0 to 9.
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits
Contains a value from 0 to 5.
bit 3-0
SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits
Contains a value from 0 to 9.
DS33030A-page 190
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 16-11: RTCCSWT: RTCC CONTROL/SAMPLE WINDOW TIMER REGISTER(1)
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
PWCSTAB7
PWCSTAB6
PWCSTAB5
PWCSTAB4
PWCSTAB3
PWCSTAB2
PWCSTAB1
PWCSTAB0
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
PWCSAMP7 PWCSAMP6 PWCSAMP5 PWCSAMP4 PWCSAMP3 PWCSAMP2 PWCSAMP1 PWCSAMP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
PWCSTAB<7:0>: PWM Stability Window Timer bits
11111111 = Stability window is 255 TPWCCLK clock periods
.
.
.
00000000 = Stability window is 0 TPWCCLK clock periods
The sample window starts when the alarm event triggers. The stability window timer starts counting
from every alarm event when PWCEN = 1.
bit 7-0
PWCSAMP<7:0>: PWM Sample Window Timer bits
11111111 = Sample window is always enabled, even when PWCEN = 0
11111110 = Sample window is 254 TPWCCLK clock periods
.
.
.
00000000 = Sample window is 0 TPWCCLK clock periods
The sample window timer starts counting at the end of the stability window when PWCEN = 1. If
PWCSTAB<7:0> = 00000000, the sample window timer starts counting from every alarm event when
PWCEN = 1.
Note 1:
A write to this register is only allowed when RTCWREN = 1.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 191
PIC24FV16KM204 FAMILY
16.3
Calibration
16.4.1
The real-time crystal input can be calibrated using the
periodic auto-adjust feature. When properly calibrated,
the RTCC can provide an error of less than 3 seconds
per month. This is accomplished by finding the number
of error clock pulses and storing the value into the
lower half of the RCFGCAL register. The 8-bit signed
value, loaded into the lower half of RCFGCAL, is multiplied by four and will be either added or subtracted from
the RTCC timer, once every minute. Refer to the steps
below for RTCC calibration:
1.
2.
3.
Using another timer resource on the device, the
user must find the error of the 32.768 kHz crystal.
Once the error is known, it must be converted to
the number of error clock pulses per minute.
a) If the oscillator is faster than ideal (negative
result from Step 2), the RCFGCAL register value
must be negative. This causes the specified
number of clock pulses to be subtracted from
the timer counter, once every minute.
b) If the oscillator is slower than ideal (positive
result from Step 2), the RCFGCAL register value
must be positive. This causes the specified
number of clock pulses to be subtracted from
the timer counter, once every minute.
EQUATION 16-1:
(Ideal Frequency† – Measured Frequency) *
60 = Clocks per Minute
† Ideal Frequency = 32,768 Hz
Note:
16.4
The alarm feature is enabled using the ALRMEN bit.
This bit is cleared when an alarm is issued. Writes to
ALRMVAL should only take place when ALRMEN = 0.
As shown in Figure 16-2, the interval selection of the
alarm is configured through the AMASKx bits
(ALCFGRPT<13:10>). These bits determine which and
how many digits of the alarm must match the clock
value for the alarm to occur.
The alarm can also be configured to repeat based on a
preconfigured interval. The amount of times this
occurs, once the alarm is enabled, is stored in the
ARPT<7:0> bits (ALCFGRPT<7:0>). When the value
of the ARPTx bits equals 00h and the CHIME bit
(ALCFGRPT<14>) is cleared, the repeat function is
disabled, and only a single alarm will occur. The alarm
can be repeated up to 255 times by loading
ARPT<7:0> with FFh.
After each alarm is issued, the value of the ARPTx bits
is decremented by one. Once the value has reached
00h, the alarm will be issued one last time, after which,
the ALRMEN bit will be cleared automatically and the
alarm will turn off.
Indefinite repetition of the alarm can occur if the
CHIME bit = 1. Instead of the alarm being disabled
when the value of the ARPTx bits reaches 00h, it rolls
over to FFh and continues counting indefinitely while
CHIME is set.
16.4.2
Writes to the lower half of the RCFGCAL register
should only occur when the timer is turned off, or
immediately after the rising edge of the seconds pulse,
except when SECONDS = 00, 15, 30 or 45. This is due
to the auto-adjust of the RTCC at 15 second intervals.
It is up to the user to include, in the error
value, the initial error of the crystal: drift
due to temperature and drift due to crystal
aging.
ALARM INTERRUPT
At every alarm event, an interrupt is generated. In addition, an alarm pulse output is provided that operates at
half the frequency of the alarm. This output is completely synchronous to the RTCC clock and can be
used as a Trigger clock to other peripherals.
Note:
Alarm
• Configurable from half second to one year
• Enabled using the ALRMEN bit
(ALCFGRPT<15>)
• One-time alarm and repeat alarm options are
available
DS33030A-page 192
CONFIGURING THE ALARM
Advance Information
Changing any of the registers, other than
the RCFGCAL and ALCFGRPT registers,
and the CHIME bit while the alarm is
enabled (ALRMEN = 1), can result in a
false alarm event leading to a false alarm
interrupt. To avoid a false alarm event, the
timer and alarm values should only be
changed while the alarm is disabled
(ALRMEN = 0). It is recommended that
the ALCFGRPT register and CHIME bit be
changed when RTCSYNC = 0.
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 16-2:
ALARM MASK SETTINGS
Alarm Mask Setting
(AMASK<3:0>)
Day of
the
Week
Month
Day
Hours
Minutes
Seconds
0000 - Every half second
0001 - Every second
0010 - Every 10 seconds
s
0011 - Every minute
s
s
m
s
s
m
m
s
s
0100 - Every 10 minutes
0101 - Every hour
0110 - Every day
0111 - Every week
d
1000 - Every month
1001 - Every year(1)
Note 1:
16.5
m
m
h
h
m
m
s
s
h
h
m
m
s
s
d
d
h
h
m
m
s
s
d
d
h
h
m
m
s
s
Annually, except when configured for February 29.
POWER CONTROL
The RTCC includes a power control feature that allows
the device to periodically wake-up an external device,
wait for the device to be stable before sampling wake-up
events from that device and then shut down the external
device. This can be done completely autonomously by
the RTCC, without the need to wake from the current
low-power mode (Sleep, Deep Sleep, etc.).
To enable this feature, the RTCC must be enabled
(RTCEN = 1), the PWCEN register bit must be set and
the RTCC pin must be driving the PWC control signal
(RTCOE = 1 and RTCCLK<1:0> = 11).
 2013 Microchip Technology Inc.
The polarity of the PWC control signal may be chosen
using the PWCPOL register bit. Active-low or
active-high may be used with the appropriate external
switch to turn on or off the power to one or more external devices. The active-low setting may also be used in
conjunction with an open-drain setting on the RTCC
pin. This setting is able to drive the GND pin(s) of the
external device directly (with the appropriate external
VDD pull-up device), without the need for external
switches. Finally, the CHIME bit should be set to enable
the PWC periodicity.
Advance Information
DS33030A-page 193
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 194
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
17.0
CONFIGURABLE LOGIC CELL
(CLC)
The Configurable Logic Cell (CLC) module allows the
user to specify combinations of signals as inputs to a
logic function and to use the logic output to control
other peripherals or I/O pins. This provides greater flexibility and potential in embedded designs since the CLC
FIGURE 17-1:
There are four input gates to the selected logic function. These four input gates select from a pool of up to
32 signals that are selected using four data source
selection multiplexers. Figure 17-1 shows an overview
of the module. Figure 17-3 shows the details of the data
source multiplexers and logic input gate connections.
CLCx MODULE
D
CLCFRZ
Input Data Selection Gates
CLCIN[0]
CLCIN[1]
CLCIN[2]
CLCIN[3]
CLCIN[4]
CLCIN[5]
CLCIN[6]
CLCIN[7]
CLCIN[8]
CLCIN[9]
CLCIN[10]
CLCIN[11]
CLCIN[12]
CLCIN[13]
CLCIN[14]
CLCIN[15]
CLCIN[16]
CLCIN[17]
CLCIN[18]
CLCIN[19]
CLCIN[20]
CLCIN[21]
CLCIN[22]
CLCIN[23]
CLCIN[24]
CLCIN[25]
CLCIN[26]
CLCIN[27]
CLCIN[28]
CLCIN[29]
CLCIN[30]
CLCIN[31]
module can operate outside the limitations of software
execution and supports a vast amount of output
designs.
Q
LCOUT
LE
See Figure 17-2
Gate 1
Gate 2
LCOE
LCEN
CLCx
Output
Logic
Gate 3 Function Logic
Output
Gate 4
LCPOL
MODE<2:0>
TRISx Control
CLCx
Interrupt
det
INTP
INTN
Sets
CLCxIF
Flag
Interrupt
det
See Figure 17-3
Note:
All register bits shown in this figure can be found in the CLCxCONL register.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 195
PIC24FV16KM204 FAMILY
FIGURE 17-2:
LOGIC FUNCTION COMBINATORIAL OPTIONS
AND – OR
OR – XOR
Gate 1
Gate 1
Gate 2
Logic Output
Gate 3
Gate 4
Gate 2
Logic Output
Gate 3
Gate 4
MODE<2:0> = 000
MODE<2:0> = 001
4-Input AND
S-R Latch
Gate 1
Gate 1
Gate 2
Gate 2
Logic Output
Gate 3
S
Gate 3
Logic Output
R
Gate 4
Gate 4
Q
MODE<2:0> = 010
MODE<2:0> = 011
1-Input D Flip-Flop with S and R
2-Input D Flip-Flop with R
Gate 4
Gate 2
D
S
Gate 4
Q
Logic Output
D
Gate 2
Gate 1
Gate 1
Q
Logic Output
R
R
Gate 3
Gate 3
MODE<2:0> = 100
MODE<2:0> = 101
J-K Flip-Flop with R
1-Input Transparent Latch with S and R
Gate 4
Gate 2
J
Q
Logic Output
Gate 1
Gate 4
K
R
Gate 2
D
Gate 1
LE
Gate 3
S
Q
Logic Output
R
Gate 3
MODE<2:0> = 110
DS33030A-page 196
MODE<2:0> = 111
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 17-3:
CLCx INPUT SOURCE SELECTION DIAGRAM
Data Selection
CLCIN[0]
CLCIN[1]
CLCIN[2]
CLCIN[3]
CLCIN[4]
CLCIN[5]
CLCIN[6]
CLCIN[7]
000
Data Gate 1
Data 1 Non-Inverted
G1D1T
Data 1
Inverted
G1D1N
111
DS1x (CLCxSEL<2:0>)
G1D2T
G1D2N
CLCIN[8]
CLCIN[9]
CLCIN[10]
CLCIN[11]
CLCIN[12]
CLCIN[13]
CLCIN[14]
CLCIN[15]
G1D3T
Data 2 Non-Inverted
Data 2
Inverted
G1D3N
G1D4T
G1D4N
000
Data Gate 2
Data 3 Non-Inverted
Data 3
Inverted
Gate 2
(Same as Data Gate 1)
Data Gate 3
111
Gate 3
DS3x (CLCxSEL<10:8>)
CLCIN[24]
CLCIN[25]
CLCIN[26]
CLCIN[27]
CLCIN[28]
CLCIN[29]
CLCIN[30]
CLCIN[31]
G1POL
(CLCxCONH<0>)
111
DS2x (CLCxSEL<6:4>)
CLCIN[16]
CLCIN[17]
CLCIN[18]
CLCIN[19]
CLCIN[20]
CLCIN[21]
CLCIN[22]
CLCIN[23]
Gate 1
000
(Same as Data Gate 1)
Data Gate 4
000
Gate 4
Data 4 Non-Inverted
(Same as Data Gate 1)
Data 4
Inverted
111
DS4x (CLCxSEL<14:12>)
Note:
All controls are undefined at power-up.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 197
PIC24FV16KM204 FAMILY
17.1
Control Registers
The CLCx Source Select register (CLCxSEL) allows
the user to select up to 4 data input sources using the
4 data input selection multiplexers. Each multiplexer
has a list of 8 data sources available.
The CLCx module is controlled by the following registers:
•
•
•
•
•
CLCxCONL
CLCxCONH
CLCxSEL
CLCxGLSL
CLCxGLSH
The CLCx Gate Logic Select registers (CLCxGLSL and
CLCxGLSH) allow the user to select which outputs
from each of the selection MUXes are used as inputs to
the input gates of the logic cell. Each data source MUX
outputs both a true and a negated version of its output.
All of these 8 signals are enabled, ORed together by
the logic cell input gates.
The CLCx Control registers (CLCxCONL and
CLCxCONH) are used to enable the module and interrupts, control the output enable bit, select output polarity
and select the logic function. The CLCx Control registers
also allow the user to control the logic polarity of not only
the cell output, but also some intermediate variables.
REGISTER 17-1:
CLCxCONL: CLCx CONTROL REGISTER (LOW)
R/W-0
U-0
U-0
U-0
R/W-0
R/W-0
U-0
U-0
LCEN
—
—
—
INTP
INTN
—
—
bit 15
bit 8
R-0
R-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
LCOE
LCOUT
LCPOL
—
—
MODE2
MODE1
MODE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
LCEN: CLCx Enable bit
1 = CLCx is enabled and mixing input signals
0 = CLCx is disabled and has logic zero outputs
bit 14-12
Unimplemented: Read as ‘0’
bit 11
INTP: CLCx Positive Edge Interrupt Enable bit
1 = Interrupt will be generated when a rising edge occurs on LCOUT
0 = Interrupt will not be generated
bit 10
INTN: CLCx Negative Edge Interrupt Enable bit
1 = Interrupt will be generated when a falling edge occurs on LCOUT
0 = Interrupt will not be generated
bit 9-8
Unimplemented: Read as ‘0’
bit 7
LCOE: CLCx Port Enable bit
1 = CLCx port pin output is enabled
0 = CLCx port pin output is disabled
bit 6
LCOUT: CLCx Data Output Status bit
1 = CLCx output high
0 = CLCx output low
bit 5
LCPOL: CLCx Output Polarity Control bit
1 = The output of the module is inverted
0 = The output of the module is not inverted
bit 4-3
Unimplemented: Read as ‘0’
DS33030A-page 198
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 17-1:
bit 2-0
CLCxCONL: CLCx CONTROL REGISTER (LOW) (CONTINUED)
MODE<2:0>: CLCx Mode bits
111 = Cell is a 1-input transparent latch with S and R
110 = Cell is a JK flip-flop with R
101 = Cell is a 2-input D flip-flop with R
100 = Cell is a 1-input D flip-flop with S and R
011 = Cell is an SR latch
010 = Cell is a 4-input AND
001 = Cell is an OR-XOR
000 = Cell is a AND-OR
REGISTER 17-2:
CLCxCONH: CLCx CONTROL REGISTER (HIGH)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
—
G4POL
G3POL
G2POL
G1POL
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
HSC = Hardware Settable/Clearable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-4
Unimplemented: Read as ‘0’
bit 3
G4POL: Gate 4 Polarity Control bit
1 = The output of Channel 4 logic is inverted when applied to the logic cell
0 = The output of Channel 4 logic is not inverted
bit 2
G3POL: Gate 3 Polarity Control bit
1 = The output of Channel 3 logic is inverted when applied to the logic cell
0 = The output of Channel 3 logic is not inverted
bit 1
G2POL: Gate 2 Polarity Control bit
1 = The output of Channel 2 logic is inverted when applied to the logic cell
0 = The output of Channel 2 logic is not inverted
bit 0
G1POL: Gate 1 Polarity Control bit
1 = The output of Channel 1 logic is inverted when applied to the logic cell
0 = The output of Channel 1 logic is not inverted
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 199
PIC24FV16KM204 FAMILY
REGISTER 17-3:
CLCxSEL: CLCx INPUT MUX SELECT REGISTER
U-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
—
DS42
DS41
DS40
—
DS32
DS31
DS30
bit 15
bit 8
U-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
—
DS22
DS21
DS20
—
DS12
DS11
DS10
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
DS4<2:0>: Data Selection MUX 4 Signal Selection bits
111 = MCCP3 event flag
110 = MCCP1 event flag
101 = Digital logic high
100 = CTMU Trigger interrupt
For CLC1:
011 = SPI1 SDIx
010 = Comparator 3 output
001 = CLC2 output
000 = CLCINB I/O pin
For CLC2:
011 = SPI2 SDIx
010 = Comparator 3 output
001 = CLC1 output
000 = CLCINB I/O pin
bit 11
Unimplemented: Read as ‘0’
bit 10-8
DS3<2:0>: Data Selection MUX 3 Signal Selection bits
111 = MCCP3 event flag
110 = MCCP2 event flag
101 = Digital logic high
For CLC1:
100 = UART1 RX
011 = SPI1 SDOx
010 = Comparator 2 output
001 = CLC1 output
000 = CLCINA I/O pin
For CLC2:
100 = UART2 RX
011 = SPI2 SDOx
010 = Comparator 2 output
001 = CLC2 output
000 = CLCINA I/O pin
bit 7
Unimplemented: Read as ‘0’
DS33030A-page 200
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 17-3:
CLCxSEL: CLCx INPUT MUX SELECT REGISTER (CONTINUED)
bit 6-4
DS2<2:0>: Data Selection MUX 2 Signal Selection bits
111 = MCCP2 event flag
110 = MCCP1 event flag
101 = Digital logic high
100 = A/D end of conversion event
For CLC1:
011 = UART1 TX
010 = Comparator 1 output
001 = CLC2 output
000 = CLCINB I/O pin
For CLC2:
011 = UART2 TX
010 = Comparator 1 output
001 = CLC1 output
000 = CLCINB I/O pin
bit 3
Unimplemented: Read as ‘0’
bit 2-0
DS1<2:0>: Data Selection MUX 1 Signal Selection bits
111 = SCCP5 Event Flag
110 = SCCP4 Event Flag
101 = Digital Logic High
100 = 8 MHz FRC clock source
011 = LPRC clock source
010 = SOSC clock source
001 = System Clock (TCY)
000 = CLCINA I/O pin
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 201
PIC24FV16KM204 FAMILY
REGISTER 17-4:
CLCxGLSL: CLCx GATE LOGIC INPUT SELECT LOW REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
G2D4T
G2D4N
G2D3T
G2D3N
G2D2T
G2D2N
G2D1T
G2D1N
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
G1D4T
G1D4N
G1D3T
G1D3N
G1D2T
G1D2N
G1D1T
G1D1N
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
G2D4T: Gate 2 Data Source 4 True Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 2
0 = The Data Source 4 inverted signal is disabled for Gate 2
bit 14
G2D4N: Gate 2 Data Source 4 Negated Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 2
0 = The Data Source 4 inverted signal is disabled for Gate 2
bit 13
G2D3T: Gate 2 Data Source 3 True Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 2
0 = The Data Source 3 inverted signal is disabled for Gate 2
bit 12
G2D3N: Gate 2 Data Source 3 Negated Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 2
0 = The Data Source 3 inverted signal is disabled for Gate 2
bit 11
G2D2T: Gate 2 Data Source 2 True Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 2
0 = The Data Source 2 inverted signal is disabled for Gate 2
bit 10
G2D2N: Gate 2 Data Source 2 Negated Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 2
0 = The Data Source 2 inverted signal is disabled for Gate 2
bit 9
G2D1T: Gate 2 Data Source 1 True Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 2
0 = The Data Source 1 inverted signal is disabled for Gate 2
bit 8
G2D1N: Gate 2 Data Source 1 Negated Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 1
0 = The Data Source 2 inverted signal is disabled for Gate 1
bit 7
G1D4T: Gate 1 Data Source 4 True Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 1
0 = The Data Source 4 inverted signal is disabled for Gate 1
bit 6
G1D4N: Gate 1 Data Source 4 Negated Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 1
0 = The Data Source 4 inverted signal is disabled for Gate 1
bit 5
G1D3T: Gate 1 Data Source 3 True Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 1
0 = The Data Source 3 inverted signal is disabled for Gate 1
bit 4
G1D3N: Gate 1 Data Source 3 Negated Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 1
0 = The Data Source 3 inverted signal is disabled for Gate 1
DS33030A-page 202
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 17-4:
CLCxGLSL: CLCx GATE LOGIC INPUT SELECT LOW REGISTER (CONTINUED)
bit 3
G1D2T: Gate 1 Data Source 2 True Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 1
0 = The Data Source 2 inverted signal is disabled for Gate 1
bit 2
G1D2N: Gate 1 Data Source 2 Negated Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 1
0 = The Data Source 2 inverted signal is disabled for Gate 1
bit 1
G1D1T: Gate 1 Data Source 1 True Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 1
0 = The Data Source 1 inverted signal is disabled for Gate 1
bit 0
G1D1N: Gate 1 Data Source 1 Negated Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 1
0 = The Data Source 1 inverted signal is disabled for Gate 1
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 203
PIC24FV16KM204 FAMILY
REGISTER 17-5:
CLCxGLSH: CLCx GATE LOGIC INPUT SELECT HIGH REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
G4D4T
G4D4N
G4D3T
G4D3N
G4D2T
G4D2N
G4D1T
G4D1N
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
G3D4T
G3D4N
G3D3T
G3D3N
G3D2T
G3D2N
G3D1T
G3D1N
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
HSC = Hardware Settable/Clearable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
G4D4T: Gate 4 Data Source 4 True Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 4
0 = The Data Source 4 inverted signal is disabled for Gate 4
bit 14
G4D4N: Gate 4 Data Source 4 Negated Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 4
0 = The Data Source 4 inverted signal is disabled for Gate 4
bit 13
G4D3T: Gate 4 Data Source 3 True Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 4
0 = The Data Source 3 inverted signal is disabled for Gate 4
bit 12
G4D3N: Gate 4 Data Source 3 Negated Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 4
0 = The Data Source 3 inverted signal is disabled for Gate 4
bit 11
G4D2T: Gate 4 Data Source 2 True Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 4
0 = The Data Source 2 inverted signal is disabled for Gate 4
bit 10
G4D2N: Gate 4 Data Source 2 Negated Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 4
0 = The Data Source 2 inverted signal is disabled for Gate 4
bit 9
G4D1T: Gate 4 Data Source 1 True Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 4
0 = The Data Source 1 inverted signal is disabled for Gate 4
bit 8
G4D1N: Gate 4 Data Source 1 Negated Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 4
0 = The Data Source 1 inverted signal is disabled for Gate 4
bit 7
G3D4T: Gate 3 Data Source 4 True Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 3
0 = The Data Source 4 inverted signal is disabled for Gate 3
bit 6
G3D4N: Gate 3 Data Source 4 Negated Enable bit
1 = The Data Source 4 inverted signal is enabled for Gate 3
0 = The Data Source 4 inverted signal is disabled for Gate 3
bit 5
G3D3T: Gate 3 Data Source 3 True Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 3
0 = The Data Source 3 inverted signal is disabled for Gate 3
bit 4
G3D3N: Gate 3 Data Source 3 Negated Enable bit
1 = The Data Source 3 inverted signal is enabled for Gate 3
0 = The Data Source 3 inverted signal is disabled for Gate 3
DS33030A-page 204
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 17-5:
CLCxGLSH: CLCx GATE LOGIC INPUT SELECT HIGH REGISTER (CONTINUED)
bit 3
G3D2T: Gate 3 Data Source 2 True Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 3
0 = The Data Source 2 inverted signal is disabled for Gate 3
bit 2
G3D2N: Gate 3 Data Source 2 Negated Enable bit
1 = The Data Source 2 inverted signal is enabled for Gate 3
0 = The Data Source 2 inverted signal is disabled for Gate 3
bit 1
G3D1T: Gate 3 Data Source 1 True Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 3
0 = The Data Source 1 inverted signal is disabled for Gate 3
bit 0
G3D1N: Gate 3 Data Source 1 Negated Enable bit
1 = The Data Source 1 inverted signal is enabled for Gate 3
0 = The Data Source 1 inverted signal is disabled for Gate 3
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 205
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 206
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
18.0
HIGH/LOW-VOLTAGE DETECT
(HLVD)
Note:
An interrupt flag is set if the device experiences an
excursion past the trip point in the direction of change.
If the interrupt is enabled, the program execution will
branch to the interrupt vector address and the software
can then respond to the interrupt.
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on the
High/Low-Voltage Detect, refer to the
“PIC24F Family Reference Manual”,
Section 36. “High-Level Integration
with Programmable High/Low-Voltage
Detect (HLVD)” (DS39725).
The HLVD Control register (see Register 18-1) completely controls the operation of the HLVD module. This
allows the circuitry to be “turned off” by the user under
software control, which minimizes the current
consumption for the device.
The High/Low-Voltage Detect module (HLVD) is a
programmable circuit that allows the user to specify
both the device voltage trip point and the direction of
change.
FIGURE 18-1:
VDD
HIGH/LOW-VOLTAGE DETECT (HLVD) MODULE BLOCK DIAGRAM
Externally Generated
Trip Point
VDD
HLVDIN
HLVDL<3:0>
16-to-1 MUX
HLVDEN
–
VDIR
Set
HLVDIF
Internal Voltage
Reference
VBG
HLVDEN
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 207
PIC24FV16KM204 FAMILY
REGISTER 18-1:
HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
HLVDEN
—
HLSIDL
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
VDIR
BGVST
IRVST
—
HLVDL3
HLVDL2
HLVDL1
HLVDL0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
HLVDEN: High/Low-Voltage Detect Power Enable bit
1 = HLVD is enabled
0 = HLVD is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
HLSIDL: HLVD Stop in Idle Mode bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12-8
Unimplemented: Read as ‘0’
bit 7
VDIR: Voltage Change Direction Select bit
1 = Event occurs when voltage equals or exceeds trip point (HLVDL<3:0>)
0 = Event occurs when voltage equals or falls below trip point (HLVDL<3:0>)
bit 6
BGVST: Band Gap Voltage Stable Flag bit
1 = Indicates that the band gap voltage is stable
0 = Indicates that the band gap voltage is unstable
bit 5
IRVST: Internal Reference Voltage Stable Flag bit
1 = Indicates that the internal reference voltage is stable and the High-Voltage Detect logic generates
the interrupt flag at the specified voltage range
0 = Indicates that the internal reference voltage is unstable and the High-Voltage Detect logic will not
generate the interrupt flag at the specified voltage range, and the HLVD interrupt should not be
enabled
bit 4
Unimplemented: Read as ‘0’
bit 3-0
HLVDL<3:0>: High/Low-Voltage Detection Limit bits
1111 = External analog input is used (input comes from the HLVDIN pin)
1110 = Trip Point 1(1)
1101 = Trip Point 2(1)
1100 = Trip Point 3(1)
.
.
.
0000 = Trip Point 15(1)
Note 1:
For the actual trip point, see Section 27.0 “Electrical Characteristics”.
DS33030A-page 208
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
19.0
Note:
12-BIT A/D CONVERTER WITH
THRESHOLD DETECT
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on the 12-Bit
A/D Converter with Threshold Detect, refer
to the “PIC24F Family Reference Manual”,
Section 51. “12-Bit A/D Converter with
Threshold Detect” (DS39739).
The PIC24F 12-bit A/D Converter has the following key
features:
• Successive Approximation Register (SAR)
Conversion
• Conversion Speeds of up to 100 ksps
• Up to 32 Analog Input Channels (Internal and
External)
• Multiple Internal Reference Input Channels
• External Voltage Reference Input Pins
• Unipolar Differential Sample-and-Hold (S/H)
Amplifier
• Automated Threshold Scan and Compare
Operation to Pre-Evaluate Conversion Results
• Selectable Conversion Trigger Source
• Fixed-Length (one word per channel),
Configurable Conversion Result Buffer
• Four Options for Results Alignment
• Configurable Interrupt Generation
• Operation During CPU Sleep and Idle modes
 2013 Microchip Technology Inc.
The 12-bit A/D Converter module is an enhanced
version of the 10-bit module offered in some PIC24
devices. Both modules are Successive Approximation
Register (SAR) converters at their cores, surrounded
by a range of hardware features for flexible
configuration. This version of the module extends
functionality by providing 12-bit resolution, a wider
range of automatic sampling options and tighter
integration with other analog modules, such as the
CTMU, and a configurable results buffer. There is a
legacy 10-bit mode on this A/D to allow the option to run
with lower resolution in order to obtain higher
throughput. This module also includes a unique
Threshold Detect feature that allows the module itself
to make simple decisions based on the conversion
results.
A simplified block diagram for the module is illustrated
in Figure 19-1.
Advance Information
DS33030A-page 209
PIC24FV16KM204 FAMILY
FIGURE 19-1:
12-BIT A/D CONVERTER BLOCK DIAGRAM
Internal
Data Bus
AVSS
VREF+
VREF-
VR Select
AVDD
VR+
16
VR-
VBG
Comparator
VINH
VINL
AN0
VRS/H
VR+
DAC
AN1
10/12-Bit SAR
AN2
Conversion Logic
AN3
Data Formatting
AN4
VINH
AN6
AN7
ADC1BUF0:
ADC1BUF17
MUX A
AN5
AN8
AD1CON1
AD1CON2
VINL
AN9
AD1CON3
AD1CON5
AD1CHS
AD1CHITL
AN21
CTMU
Temp. Sensor
CTMU
MUX B
AN20
AD1CHITH
AD1CSSL
AD1CSSH
VINH
VINL
Sample Control
VBG
0.785 * VDD
Control Logic
Conversion Control
Input MUX Control
Pin Config. Control
0.215 * VDD
AVDD
AVss
DS33030A-page 210
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
To perform an A/D conversion:
1.
2.
2.
Configure the A/D module:
a) Configure the port pins as analog inputs
and/or select band gap reference inputs
(ANS<12:10>, ANS<5:0>).
b) Select voltage reference source to match
the expected range on the analog inputs
(AD1CON2<15:13>).
c) Select the analog conversion clock to
match the desired data rate with the
processor clock (AD1CON3<7:0>).
d) Select the appropriate sample/conversion
sequence
(AD1CON1<7:4>
and
AD1CON3<12:8>).
e) Configure the MODE12 bit to select A/D
resolution (AD1CON1<10>).
f) Select how conversion results are
presented in the buffer (AD1CON1<9:8>).
g) Select the interrupt rate (AD1CON2<6:2>).
h) Turn on the A/D module (AD1CON1<15>).
Configure the A/D interrupt (if required):
a) Clear the AD1IF bit.
b) Select the A/D interrupt priority.
Configure the threshold compare channels:
a) Enable auto-scan; set the ASEN bit
(AD1CON5<15>).
b) Select the Compare mode “Greater Than,
Less Than or Windowed”; set the CMx bits
(AD1CON5<1:0>).
c) Select the threshold compare channels to
be scanned (AD1CSSH, AD1CSSL).
d) If the CTMU is required as a current
source for a threshold compare channel,
enable the corresponding CTMU channel
(AD1CTMENH, AD1CTMENL).
e) Write the threshold values into the
corresponding ADC1BUFn registers.
f) Turn on the A/D module (AD1CON1<15>).
Note:
3.
If performing an A/D sample and
conversion using Threshold Detect in
Sleep Mode, the RC A/D clock source
must be selected before entering into
Sleep mode.
Configure the A/D interrupt (OPTIONAL):
a) Clear the AD1IF bit.
b) Select the A/D interrupt priority.
To perform an A/D sample and conversion using
Threshold Detect scanning:
1.
Configure the A/D module:
a) Configure the port pins as analog inputs
(ANS<12:10>, ANS<5,0>).
b) Select the voltage reference source to
match the expected range on the analog
inputs (AD1CON2<15:13>).
c) Select the analog conversion clock to
match the desired data rate with the
processor clock (AD1CON3<7:0>).
d) Select the appropriate sample/conversion
sequence
(AD1CON1<7:4>
and
AD1CON3<12:8>).
e) Configure the MODE12 bit to select A/D
resolution (AD1CON1<10>).
f) Select how the conversion results are
presented in the buffer (AD1CON1<9:8>).
g) Select the interrupt rate (AD1CON2<6:2>).
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 211
PIC24FV16KM204 FAMILY
19.1
A/D Control Registers
The 12-bit A/D Converter module uses up to
43 registers for its operation. All registers are mapped
in the data memory space.
19.1.1
CONTROL REGISTERS
Depending on the specific device, the module has up to
eleven control and status registers:
•
•
•
•
•
•
AD1CON1: A/D Control Register 1
AD1CON2: A/D Control Register 2
AD1CON3: A/D Control Register 3
AD1CON5: A/D Control Register 5
AD1CHS: A/D Sample Select Register
AD1CHITH and AD1CHITL: A/D Scan Compare
Hit Registers
• AD1CSSH and AD1CSSL: A/D Input Scan Select
Registers
• AD1CTMENH and AD1CTMENL: CTMU Enable
Registers
The AD1CON1, AD1CON2 and AD1CON3 registers
(Register 19-1, Register 19-2 and Register 19-3)
control the overall operation of the A/D module. This
includes enabling the module, configuring the
conversion clock and voltage reference sources,
selecting the sampling and conversion Triggers, and
manually controlling the sample/convert sequences.
The AD1CON5 register (Register 19-4) specifically
controls features of the Threshold Detect operation,
including its function in power-saving modes.
The AD1CHS register (Register 19-5) selects the input
channels to be connected to the S/H amplifier. It also
allows the choice of input multiplexers and the
selection of a reference source for differential
sampling.
DS33030A-page 212
The
AD1CHITH
and
AD1CHITL
registers
(Register 19-6 and Register 19-7) are semaphore
registers used with Threshold Detect operations. The
status of individual bits, or bit pairs in some cases,
indicates if a match condition has occurred. AD1CHITL
is always implemented, whereas AD1CHITH may not
be implemented in devices with 16 or fewer channels.
The AD1CSSH/L registers (Register 19-8 and
Register 19-9) select the channels to be included for
sequential scanning.
The AD1CTMENH/L registers (Register 19-10 and
Register 19-11) select the channel(s) to be used by the
CTMU during conversions. Selecting a particular
channel allows the A/D Converter to control the CTMU
(particularly, its current source) and read its data
through that channel. AD1CTMENL is always
implemented, whereas AD1CTMENH may not be
implemented in devices with 16 or fewer channels.
19.1.2
A/D RESULT BUFFERS
The module incorporates a multi-word, dual port buffer,
called ADC1BUFn. Each of the locations is mapped
into the data memory space and is separately
addressable. The buffer locations are referred to as
ADC1BUF0 through ADC1BUFn (up to 17).
The A/D result buffers are both readable and writable.
When the module is active (AD1CON<15> = 1), the
buffers are read-only and store the results of A/D
conversions. When the module is inactive
(AD1CON<15> = 0), the buffers are both readable and
writable. In this state, writing to a buffer location
programs a conversion threshold for Threshold Detect
operations.
Buffer contents are not cleared when the module is
deactivated with the ADON bit (AD1CON1<15>).
Conversion results and any programmed threshold
values are maintained when ADON is set or cleared.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 19-1:
AD1CON1: A/DA/D CONTROL REGISTER 1
R/W-0
U-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
ADON
—
ADSIDL
—
—
MODE12
FORM1
FORM0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0, HSC
R/C-0, HSC
SSRC3
SSRC2
SSRC1
SSRC0
—
ASAM
SAMP
DONE
bit 7
bit 0
Legend:
C = Clearable bit
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
HSC = Hardware Settable/Clearable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ADON: A/D Operating Mode bit
1 = A/D Converter module is operating
0 = A/D Converter is off
bit 14
Unimplemented: Read as ‘0’
bit 13
ADSIDL: A/D Stop in Idle Mode bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12-11
Unimplemented: Read as ‘0’
bit 10
MODE12: 12-Bit Operation Mode bit
1 = 12-bit A/D operation
0 = 10-bit A/D operation
bit 9-8
FORM<1:0>: Data Output Format bits (see the following formats)
11 = Fractional result, signed, left-justified
10 = Absolute fractional result, unsigned, left-justified
01 = Decimal result, signed, right-justified
00 = Absolute decimal result, unsigned, right-justified
bit 7-4
SSRC<3:0>: Sample Clock Source Select bits
1111 = Reserved



1101 = Reserved
1100 = CLC2 event ends sampling and starts conversion
1011 = SCCP4 event ends sampling and starts conversion
1010 = MCCP3 event ends sampling and starts conversion
1001 = MCCP2 event ends sampling and starts conversion
1000 = CLC1 event ends sampling and starts conversion
0111 = Internal counter ends sampling and starts conversion (auto-convert)
0110 = TMR1 Sleep mode Trigger event ends sampling and starts conversion(1)
0101 = TMR1 event ends sampling and starts conversion
0100 = CTMU event ends sampling and starts conversion
0011 = SCCP5 event ends sampling and starts conversion
0010 = MCCP1 event ends sampling and starts conversion
0001 = INT0 event ends sampling and starts conversion
0000 = Clearing sample bit ends sampling and starts conversion
Note 1:
This version of the TMR1 Trigger allows A/D conversions to be triggered from TMR1 while the device is
operating in Sleep mode. The SSRC<3:0> = 0101 option allows conversions to be triggered in Run or Idle
modes only.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 213
PIC24FV16KM204 FAMILY
REGISTER 19-1:
AD1CON1: A/DA/D CONTROL REGISTER 1 (CONTINUED)
bit 3
Unimplemented: Read as ‘0’
bit 2
ASAM: A/D Sample Auto-Start bit
1 = Sampling begins immediately after the last conversion; SAMP bit is auto-set
0 = Sampling begins when the SAMP bit is manually set
bit 1
SAMP: A/D Sample Enable bit
1 = A/D Sample-and-Hold amplifiers are sampling
0 = A/D Sample-and-Hold amplifiers are holding
bit 0
DONE: A/D Conversion Status bit
1 = A/D conversion cycle has completed
0 = A/D conversion cycle has not started or is in progress
Note 1:
This version of the TMR1 Trigger allows A/D conversions to be triggered from TMR1 while the device is
operating in Sleep mode. The SSRC<3:0> = 0101 option allows conversions to be triggered in Run or Idle
modes only.
DS33030A-page 214
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 19-2:
AD1CON2: A/D CONTROL REGISTER 2
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
U-0
U-0
PVCFG1
PVCFG0
NVCFG0
—
BUFREGEN
CSCNA
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
BUFS(1)
SMPI4
SMPI3
SMPI2
SMPI1
SMPI0
BUFM(1)
ALTS
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
PVCFG<1:0>: Converter Positive Voltage Reference Configuration bits
11 = 4 * Internal VBG(2)
10 = 2 * Internal VBG(3)
01 = External VREF+
00 = AVDD
bit 13
NVCFG0: Converter Negative Voltage Reference Configuration bits
1 = External VREF0 = AVSS
bit 12
Unimplemented: Read as ‘0’
bit 11
BUFREGEN: A/D Buffer Register Enable bit
1 = Conversion result is loaded into a buffer location determined by the converted channel
0 = A/D result buffer is treated as a FIFO
bit 10
CSCNA: Scan Input Selections for CH0+ S/H Input for MUX A Setting bit
1 = Scans inputs
0 = Does not scan inputs
bit 9-8
Unimplemented: Read as ‘0’
bit 7
BUFS: Buffer Fill Status bit(1)
1 = A/D is filling the upper half of the buffer; user should access data in the lower half
0 = A/D is filling the lower half of the buffer; user should access data in the upper half
bit 6-2
SMPI<4:0>: Interrupt Sample Rate Select bits
11111 = Interrupts at the completion of the conversion for each 32nd sample
11110 = Interrupts at the completion of the conversion for each 31st sample



00001 = Interrupts at the completion of the conversion for every other sample
00000 = Interrupts at the completion of the conversion for each sample
bit 1
BUFM: Buffer Fill Mode Select bit(1)
1 = Starts filling the buffer at address, AD1BUF0, on the first interrupt and AD1BUF(n/2) on the next
interrupt (Split Buffer mode)
0 = Starts filling the buffer at address, ADCBUF0, and each sequential address on successive
interrupts (FIFO mode)
bit 0
ALTS: Alternate Input Sample Mode Select bit
1 = Uses channel input selects for Sample A on the first sample and Sample B on the next sample
0 = Always uses channel input selects for Sample A
Note 1:
2:
3:
This is only applicable when the buffer is used in FIFO mode (BUFREGEN = 0). In addition, BUFS is only
used when BUFM = 1.
The voltage reference setting will not be within the specification with VDD below 4.5V.
The voltage reference setting will not be within the specification with VDD below 2.3V.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 215
PIC24FV16KM204 FAMILY
REGISTER 19-3:
AD1CON3: A/D CONTROL REGISTER 3
R/W-0
R-0
r-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADRC
EXTSAM
r
SAMC4
SAMC3
SAMC2
SAMC1
SAMC0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCS7
ADCS6
ADCS5
ADCS4
ADCS3
ADCS2
ADCS1
ADCS0
bit 7
bit 0
Legend:
r = Reserved bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
ADRC: A/D Conversion Clock Source bit
1 = RC clock
0 = Clock is derived from the system clock
bit 14
EXTSAM: Extended Sampling Time bit
1 = A/D is still sampling after SAMP = 0
0 = A/D is finished sampling
bit 13
Reserved: Maintain as ‘0’
bit 12-8
SAMC<4:0>: Auto-Sample Time Select bits
11111 = 31 TAD



00001 = 1 TAD
00000 = 0 TAD
bit 7-0
ADCS<7:0>: A/D Conversion Clock Select bits
11111111-01000000 = Reserved
00111111 = 64 * TCY = TAD



00000001 = 2 * TCY = TAD
00000000 = TCY = TAD
DS33030A-page 216
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 19-4:
AD1CON5: A/D CONTROL REGISTER 5
R/W-0
R/W-0
R/W-0
R/W-0
r-0
U-0
R/W-0
R/W-0
ASEN(1)
LPEN
CTMREQ
BGREQ
r
—
ASINT1
ASINT0
bit 15
bit 8
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
—
WM1
WM0
CM1
CM0
bit 7
bit 0
Legend:
r = Reserved bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ASEN: Auto-Scan Enable bit(1)
1 = Auto-scan is enabled
0 = Auto-scan is disabled
bit 14
LPEN: Low-Power Enable bit
1 = Returns to Low-Power mode after scan
0 = Remains in Full-Power mode after scan
bit 13
CTMREQ: CTMU Request bit
1 = CTMU is enabled when the A/D is enabled and active
0 = CTMU is not enabled by the A/D
bit 12
BGREQ: Band Gap Request bit
1 = Band gap is enabled when the A/D is enabled and active
0 = Band gap is not enabled by the A/D
bit 11
Reserved: Maintain as ‘0’
bit 10
Unimplemented: Read as ‘0’
bit 9-8
ASINT<1:0>: Auto-Scan (Threshold Detect) Interrupt Mode bits
11 = Interrupt after a Threshold Detect sequence has completed and a valid compare has occurred
10 = Interrupt after a valid compare has occurred
01 = Interrupt after a Threshold Detect sequence has completed
00 = No interrupt
bit 7-4
Unimplemented: Read as ‘0’
bit 3-2
WM<1:0>: Write Mode bits
11 = Reserved
10 = Auto-compare only (conversion results are not saved, but interrupts are generated when a valid
match, as defined by the CMx and ASINTx bits, occurs)
01 = Convert and save (conversion results are saved to locations as determined by the register bits when
a match, as defined by the CMx bits, occurs)
00 = Legacy operation (conversion data is saved to a location determined by the buffer register bits)
bit 1-0
CM<1:0>: Compare Mode bits
11 = Outside Window mode (valid match occurs if the conversion result is outside of the window defined by
the corresponding buffer pair)
10 = Inside Window mode (valid match occurs if the conversion result is inside the window defined by the
corresponding buffer pair)
01 = Greater Than mode (valid match occurs if the result is greater than the value in the corresponding buffer
register)
00 = Less Than mode (valid match occurs if the result is less than the value in the corresponding buffer register)
Note 1:
When using auto-scan with Threshold Detect (ASEN = 1), do not configure the sample clock source to
Auto-Convert mode (SSRC<3:0> = 7). Any other available SSRC selection is valid. To use auto-convert as
the sample clock source (SSRC<3:0> = 7), make sure ASEN is cleared.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 217
PIC24FV16KM204 FAMILY
REGISTER 19-5:
AD1CHS: A/D SAMPLE SELECT REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CH0NB2
CH0NB1
CH0NB0
CH0SB4
CH0SB3
CH0SB2
CH0SB1
CH0SB0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CH0NA2
CH0NA1
CH0NA0
CH0SA4
CH0SA3
CH0SA2
CH0SA1
CH0SA0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-13
CH0NB<2:0>: Sample B Channel 0 Negative Input Select bits
111 = AN6(1)
110 = AN5(2)
101 = AN4
100 = AN3
011 = AN2
010 = AN1
001 = AN0
000 = AVSS
bit 12-8
CH0SB<4:0>: S/H Amplifier Positive Input Select for MUX B Multiplexer Setting bits
11111 = Unimplemented, do not use
11110 = AVDD(3)
11101 = AVSS(3)
11100 = Upper guardband rail (0.785 * VDD)
11011 = Lower guardband rail (0.215 * VDD)
11010 = Internal Band Gap Reference (VBG)(3)
11000-11001 = Unimplemented, do not use
10001 = No channels are connected, all inputs are floating (used for CTMU)
10111 = No channels connected, all inputs are floating (used for CTMU)
10110 = No channels connected, all inputs are floating (used for CTMU temperature sensor input) –
does not require the corresponding CTMEN22 (AD1CTMENH<6>) bit)
10101 = Channel 0 positive input is AN21
10100 = Channel 0 positive input is AN20
10011 = Channel 0 positive input is AN19
10010 = Channel 0 positive input is AN18(2)
10001 = Channel 0 positive input is AN17(2)



01001 = Channel 0 positive input is AN9
01000 = Channel 0 positive input is AN8(1)
00111 = Channel 0 positive input is AN7(1)
00110 = Channel 0 positive input is AN6(1)
00101 = Channel 0 positive input is AN5(2)
00100 = Channel 0 positive input is AN4
00011 = Channel 0 positive input is AN3
00010 = Channel 0 positive input is AN2
00001 = Channel 0 positive input is AN1
00000 = Channel 0 positive input is AN0
Note 1:
2:
3:
This is implemented on 44-pin devices only.
This is implemented on 28-pin and 44-pin devices only.
The band gap value used for this input is 2x or 4x the internal VBG, which is selected when PVCFG<1:0> = 1x.
DS33030A-page 218
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 19-5:
AD1CHS: A/D SAMPLE SELECT REGISTER (CONTINUED)
bit 7-5
CH0NA<2:0>: Sample A Channel 0 Negative Input Select bits
The same definitions as for CHONB<2:0>.
bit 4-0
CH0SA<4:0>: Sample A Channel 0 Positive Input Select bits
The same definitions as for CHONA<4:0>.
Note 1:
2:
3:
This is implemented on 44-pin devices only.
This is implemented on 28-pin and 44-pin devices only.
The band gap value used for this input is 2x or 4x the internal VBG, which is selected when PVCFG<1:0> = 1x.
REGISTER 19-6:
AD1CHITH: A/D SCAN COMPARE HIT REGISTER (HIGH WORD)(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CHH23
CHH22
CHH21
CHH20
CHH19
CHH18
CHH17
CHH16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’.
bit 7-0
CHH<23:16>: A/D Compare Hit bits
If CM<1:0> = 11:
1 = A/D Result Buffer x has been written with data or a match has occurred
0 = A/D Result Buffer x has not been written with data
For All Other Values of CM<1:0>:
1 = A match has occurred on A/D Result Channel x
0 = No match has occurred on A/D Result Channel x
Note 1:
Unimplemented channels are read as ‘0’.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 219
PIC24FV16KM204 FAMILY
REGISTER 19-7:
AD1CHITL: A/D SCAN COMPARE HIT REGISTER (LOW WORD)(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CHH15
CHH14
CHH13
CHH12
CHH11
CHH10
CHH9
CHH8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CHH7
CHH6
CHH5
CHH4
CHH3
CHH2
CHH1
CHH0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
CHH<15:0>: A/D Compare Hit bits
If CM<1:0> = 11:
1 = A/D Result Buffer x has been written with data or a match has occurred
0 = A/D Result Buffer x has not been written with data
For All Other Values of CM<1:0>:
1 = A match has occurred on A/D Result Channel n
0 = No match has occurred on A/D Result Channel n
Unimplemented channels are read as ‘0’.
DS33030A-page 220
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 19-8:
AD1CSSH: A/D INPUT SCAN SELECT REGISTER (HIGH WORD)(1)
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
—
CSS30
CSS29
CSS28
CSS27
CSS26
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS23
CSS22
CSS21
CSS20
CSS19
CSS18
CSS17
CSS16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-10
CSS<30:26>: A/D Input Scan Selection bits
1 = Includes corresponding channel for input scan
0 = Skips channel for input scan
bit 9-8
Unimplemented: Read as ‘0’
bit 7-0
CSS<23:16>: A/D Input Scan Selection bits
1 = Includes corresponding channel for input scan
0 = Skips channel for input scan
Note 1:
x = Bit is unknown
Unimplemented channels are read as ‘0’. Do not select unimplemented channels for sampling as
indeterminate results may be produced.
REGISTER 19-9:
AD1CSSL: A/D INPUT SCAN SELECT REGISTER (LOW WORD)(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS15
CSS14
CSS13
CSS12
CSS11
CSS10
CSS9
CSS8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS7
CSS6
CSS5
CSS4
CSS3
CSS2
CSS1
CSS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
CSS<15:0>: A/D Input Scan Selection bits
1 = Includes corresponding ANx input for scan
0 = Skips channel for input scan
Unimplemented channels are read as ‘0’. Do not select unimplemented channels for sampling as
indeterminate results may be produced.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 221
PIC24FV16KM204 FAMILY
REGISTER 19-10: AD1CTMENH: CTMU ENABLE REGISTER (HIGH WORD)(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CTMEN23
CTMEN22
CTMEN21
CTMEN20
CTMEN19
CTMEN18
CTMEN17
CTMEN16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’.
bit 7-0
CTMEN<23:16>: CTMU Enabled During Conversion bits
1 = CTMU is enabled and connected to the selected channel during conversion
0 = CTMU is not connected to this channel
Note 1:
Unimplemented channels are read as ‘0’.
REGISTER 19-11: AD1CTMENL: CTMU ENABLE REGISTER (LOW WORD)(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CTMEN15
CTMEN14
CTMEN13
CTMEN12
CTMEN11
CTMEN10
CTMEN9
CTMEN8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CTMEN7
CTMEN6
CTMEN5
CTMEN4
CTMEN3
CTMEN2
CTMEN1
CTMEN0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
CTMEN<15:0>: CTMU Enabled During Conversion bits
1 = CTMU is enabled and connected to the selected channel during conversion
0 = CTMU is not connected to this channel
Unimplemented channels are read as ‘0’.
DS33030A-page 222
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
19.2
A/D Sampling Requirements
The analog input model of the 12-bit A/D Converter is
shown in Figure 19-2. The total sampling time for the
A/D is a function of the holding capacitor charge time.
For the A/D Converter to meet its specified accuracy,
the charge holding capacitor (CHOLD) must be allowed
to fully charge to the voltage level on the analog input
pin. The source impedance (RS), the interconnect
impedance (RIC) and the internal sampling switch
(RSS) impedance combine to directly affect the time
required to charge CHOLD. The combined impedance of
the analog sources must, therefore, be small enough to
fully charge the holding capacitor within the chosen
sample time. To minimize the effects of pin leakage
currents on the accuracy of the A/D Converter, the
maximum recommended source impedance, RS, is
2.5 k. After the analog input channel is selected
FIGURE 19-2:
(changed), this sampling function must be completed
prior to starting the conversion. The internal holding
capacitor will be in a discharged state prior to each
sample operation.
At least 1 TAD time period should be allowed between
conversions for the sample time. For more details, see
Section 29.0 “Electrical Characteristics”.
EQUATION 19-1:
A/D CONVERSION CLOCK
PERIOD
TAD = TCY (ADCS + 1)
ADCS = TAD – 1
TCY
Note:
Based on TCY = 2/FOSC; Doze mode
and PLL are disabled.
12-BIT A/D CONVERTER ANALOG INPUT MODEL
RIC  250
Rs
ANx
CPIN
VA
Sampling
Switch
RSS
ILEAKAGE
500 nA
RSS  3 k
CHOLD
= 32 pF
VSS
Legend: CPIN
= Input Capacitance
VT
= Threshold Voltage
ILEAKAGE = Leakage Current at the Pin Due to
Various Junctions
RIC
= Interconnect Resistance
RSS
= Sampling Switch Resistance
CHOLD
= Sample-and-Hold Capacitance (from DAC)
Note: The CPIN value depends on the device package and is not tested. The effect of CPIN is negligible if Rs  5 k.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 223
PIC24FV16KM204 FAMILY
19.3
Transfer Function
The transfer functions of the A/D Converter in 12-bit
resolution are shown in Figure 19-3. The difference of
the input voltages (VINH – VINL) is compared to the
reference ((VR+) – (VR-)).
• The first code transition occurs when the input
voltage is ((VR+) – (VR-))/4096 or 1.0 LSb.
• The ‘0000 0000 0001’ code is centered at
VR- + (1.5 * ((VR+) – (VR-))/4096).
FIGURE 19-3:
• The ‘0010 0000 0000’ code is centered at
VREFL + (2048.5 * ((VR+) – (VR-))/4096).
• An input voltage less than
VR- + (((VR-) – (VR-))/4096) converts as
‘0000 0000 0000’.
• An input voltage greater than
(VR-) + (4095 ((VR+) – (VR-))/4096) converts as
‘1111 1111 1111’.
12-BIT A/D TRANSFER FUNCTION
Output Code
(Binary (Decimal))
1111 1111 1111 (4095)
1111 1111 1110 (4094)
0010 0000 0011 (2051)
0010 0000 0010 (2050)
0010 0000 0001 (2049)
0010 0000 0000 (2048)
0001 1111 1111 (2047)
0001 1111 1110 (2046)
0001 1111 1101 (2045)
0000 0000 0001 (1)
DS33030A-page 224
Advance Information
(VINH – VINL)
VR+
4096
4095 * (VR+ – VR-)
VR- +
4096
VR-+
2048 * (VR+ – VR-)
4096
VR- +
Voltage Level
VR+ – VR-
0
VR-
0000 0000 0000 (0)
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
19.4
Buffer Data Formats
conversions 11 bits wide. The signed decimal format
yields 12-bit and 10-bit values, respectively. The sign bit
(bit 12 or bit 10) is sign-extended to fill the buffer. The
FORM<1:0> bits (AD1CON1<9:8>) select the format.
Figure 19-4 and Figure 19-5 show the data output formats that can be selected. Table 19-1 through
Table 19-4 show the numerical equivalents for the
various conversion result codes.
The A/D conversions are fully differential 12-bit values
when MODE12 = 1 (AD1CON1<10>) and 10-bit values
when MODE12 = 0. When absolute fractional or absolute integer formats are used, the results are 12 or
10 bits wide, respectively. When signed decimal formatting is used, the conversion also includes a sign bit,
making 12-bit conversions 13 bits wide and 10-bit
FIGURE 19-4:
A/D OUTPUT DATA FORMATS (12-BIT)
RAM Contents:
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
Read to Bus:
Integer
0
0
0
0
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
Signed Integer
s0
s0
s0
s0
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
Fractional (1.15)
Signed Fractional (1.15)
TABLE 19-1:
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
s0
0
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
0
0
0
0
0
0
NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES:
12-BIT INTEGER FORMATS
VIN/VREF
12-Bit Differential
Output Code
(13-bit result)
+4095/4096
0 1111 1111 1111
0000 1111 1111 1111
+4095
0000 1111 1111 1111
+4095
+4094/4096
0 1111 1111 1110
0000 1111 1111 1110
+4094
0000 1111 1111 1110
+4094
+1
0000 0000 0000 0001
+1
16-Bit Integer Format/
Equivalent Decimal Value
16-Bit Signed Integer Format/
Equivalent Decimal Value

+1/4096
0 1000 0000 0001
0000 0000 0000 0001
0/4096
0 0000 0000 0000
0000 0000 0000 0000
0
0000 0000 0000 0000
0
-1/4096
1 0111 1111 1111
0000 0000 0000 0000
0
1111 1111 1111 1111
-1
-4095/4096
1 0000 0000 0001
0000 0000 0000 0000
0
1111 0000 0000 0001
-4095
-4096/4096
1 0000 0000 0000
0000 0000 0000 0000
0
1111 0000 0000 0000
-4096

 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 225
PIC24FV16KM204 FAMILY
TABLE 19-2:
NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES:
12-BIT FRACTIONAL FORMATS
16-Bit Fractional Format/
Equivalent Decimal Value
12-Bit
Output Code
VIN/VREF
16-Bit Signed Fractional Format/
Equivalent Decimal Value
+4095/4096
0 1111 1111 1111
1111 1111 1111 0000
0.999
0111 1111 1111 1000
0.999
+4094/4096
0 1111 1111 1110
1111 1111 1110 0000
0.998
0111 1111 1110 1000
0.998
+1/4096
0 0000 0000 0001
0000 0000 0001 0000
0.001
0000 0000 0000 1000
0.001
0/4096
0 0000 0000 0000
0000 0000 0000 0000
0.000
0000 0000 0000 0000
0.000
-1/4096
1 0111 1111 1111
0000 0000 0000 0000
0.000
1111 1111 1111 1000
-0.001
-4095/4096
1 0000 0000 0001
0000 0000 0000 0000
0.000
1000 0000 0000 1000
-0.999
-4096/4096
1 0000 0000 0000
0000 0000 0000 0000
0.000
1000 0000 0000 0000
-1.000


FIGURE 19-5:
A/D OUTPUT DATA FORMATS (10-BIT)
RAM Contents:
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
Read to Bus:
Integer
0
0
0
0
0
0
Signed Integer
s0
s0
s0
s0
s0
s0 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
Fractional (1.15)
Signed Fractional (1.15)
TABLE 19-3:
VIN/VREF
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
0
s0 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
0
0
0
0
0
0
0
0
0
0
NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES:
10-BIT INTEGER FORMATS
10-Bit Differential
Output Code
(11-bit result)
16-Bit Integer Format/
Equivalent Decimal Value
16-Bit Signed Integer Format/
Equivalent Decimal Value
+1023/1024
011 1111 1111
0000 0011 1111 1111
1023
0000 0001 1111 1111
1023
+1022/1024
011 1111 1110
0000 0011 1111 1110
1022
0000 0001 1111 1110
1022
+1/1024
000 0000 0001
0000 0000 0000 0001
1
0000 0000 0000 0001
1
0/1024
000 0000 0000
0000 0000 0000 0000
0
0000 0000 0000 0000
0
-1/1024
101 1111 1111
0000 0000 0000 0000
0
1111 1111 1111 1111
-1
-1023/1024
100 0000 0001
0000 0000 0000 0000
0
1111 1110 0000 0001
-1023
-1024/1024
100 0000 0000
0000 0000 0000 0000
0
1111 1110 0000 0000
-1024


DS33030A-page 226
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 19-4:
VIN/VREF
NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES:
10-BIT FRACTIONAL FORMATS
10-Bit Differential
Output Code
(11-bit result)
16-Bit Fractional Format/
Equivalent Decimal Value
16-Bit Signed Fractional Format/
Equivalent Decimal Value
+1023/1024
011 1111 1111
1111 1111 1100 0000
0.999
0111 1111 1110 0000
0.999
+1022/1024
011 1111 1110
1111 1111 1000 0000
0.998
0111 1111 1000 0000
0.998
+1/1024
000 0000 0001
0000 0000 0100 0000
0.001
0000 0000 0010 0000
0.001
0/1024
000 0000 0000
0000 0000 0000 0000
0.000
0000 0000 0000 0000
0.000
-1/1024
101 1111 1111
0000 0000 0000 0000
0.000
1111 1111 1110 0000
-0.001
-1023/1024
100 0000 0001
0000 0000 0000 0000
0.000
1000 0000 0010 0000
-0.999
-1024/1024
100 0000 0000
0000 0000 0000 0000
0.000
1000 0000 0000 0000
-1.000


 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 227
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 228
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
20.0
Note:
8-BIT DIGITAL-TO-ANALOG
CONVERTER (DAC)
The DAC generates an analog output voltage based on
the digital input code, according to the formula:
VDAC =
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information, refer to the
“PIC24F Family Reference Manual”.
Device-specific information in this data
sheet supersedes the information in the
“PIC24F Family Reference Manual”.
VDACREF  DACxDAT
256
where VDAC is the analog output voltage and VDACREF
is the reference voltage selected by DACREF<1:0>.
Each DAC includes these features:
• Precision 8-bit resistor ladder for high accuracy
• Fast settling time, supporting 1 Msps effective
sampling rates
• Buffered output voltage
• Three user-selectable voltage reference options
• Multiple conversion Trigger options, plus a
manual convert-on-write option
• Left and right-justified input data options
• User-selectable Sleep and Idle mode operation
PIC24FV16KM204 family devices include two 8-bit
Digital-to-Analog Converters (DACs) for generating
analog outputs from digital data. A simplified block
diagram for a single DAC is shown in Figure 20-1. Both
of the DACs are identical.
When using the DAC, it is recommended to set the ANSx
and TRISx bits for the DACx output pin to configure it as
an analog output. See Section 11.2 “Configuring
Analog Port Pins” for more information.
FIGURE 20-1:
SINGLE DACx SIMPLIFIED BLOCK DIAGRAM
DACSIDL
Idle Mode
DACSLP
Sleep Mode
DACEN
DACOE
DACxREF
AVDD
BGBUF0
2x Gain Buffer
DACREF<1:0>
DACxCON
8
DACxDAT
8-Bit
Resistor
Ladder
DACx Trigger
Sources
32
DACxOUT
Pin
Trigger and
Interrupt Logic
DACTRIG
DACTSEL<4:0>
DACxIF
AVss
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 229
PIC24FV16KM204 FAMILY
REGISTER 20-1:
DACxCON: DACx CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
DACEN
—
DACSIDL
DACSLP
DACFM
—
SRDIS
DACTRIG
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DACOE
DACTSEL4
DACTSEL3
DACTSEL2
DACTSEL1
DACTSEL0
DACREF1
DACREF0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
DACEN: DACx Enable bit
1 = Module is enabled
0 = Module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
DACSIDL: DACx Stop in Idle Mode bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12
DACSLP: DACx Enable Peripheral During Sleep bit
1 = DACx continues to output the most recent value of DACxDAT during Sleep mode
0 = DACx is powered down in Sleep mode; DACxOUT pin is controlled by the TRISx and LATx bits
bit 11
DACFM: DACx Data Format Select bit
1 = Data is left-justified (data stored in DACxDAT<15:8>)
0 = Data is right-justified (data stored in DACxDAT<7:0>)
bit 10
Unimplemented: Read as ‘0’
bit 9
SRDIS: Soft Reset Disable bit
1 = DACxCON and DACxDAT SFRs reset only on a POR or BOR Reset
0 = DACxCON and DACxDAT SFRs reset on any type of device Reset
bit 8
DACTRIG: DACx Trigger Input Enable bit
1 = Analog output value updates when the selected (by DACTSEL<4:0>) event occurs
0 = Analog output value updates as soon as DACxDAT is written (DAC Trigger is ignored)
bit 7
DACOE: DACx Output Enable bit
1 = DACx output pin is enabled and driven on the DACxOUT pin
0 = DACx output pin is disabled, DACx output is available internally to other peripherals only
Note 1:
User must also enable Band Gap Buffer 0 (BGBUF0) and set BUFCON<1:0> to ‘00’ to obtain this voltage.
DS33030A-page 230
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 20-1:
DACxCON: DACx CONTROL REGISTER (CONTINUED)
bit 6-2
DACTSEL<4:0>: DACx Trigger Source Select bits
11101-11111 = Unused
11100 = CTMU
11011 = A/D
11010 = Comparator 1
11001 = Comparator 1
11000 = Comparator 1
10011 to 10111 = Unused
10010 = CLC2 output
10001 = CLC1 output
01100 to 10000 = Unused
01011 = Timer1 Sync output
01010 = External Interrupt 2
01001 = External Interrupt 1
01000 = External Interrupt 0
0011x = Unused
00101 = MCCP5 or SCCP5 Sync output
00100 = MCCP4 or SCCP4 Sync output
00011 = MCCP3 or SCCP3 Sync output
00010 = MCCP2 or SCCP2 Sync output
00001 = MCCP1 or SCCP1 Sync output
00000 = Unused
bit 1-0
DACREF<1:0>: DACx Reference Source Select bits
11 = 2.4V internal band gap (2 * BGBUF0)(1)
10 = AVDD
01 = DVREF+
00 = Reference is not connected (lowest power but no DAC functionality)
Note 1:
User must also enable Band Gap Buffer 0 (BGBUF0) and set BUFCON<1:0> to ‘00’ to obtain this voltage.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 231
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 232
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
21.0
Note:
DUAL OPERATIONAL
AMPLIFIER MODULE
PIC24FV16KM204 family devices include two operational amplifiers to complement the microcontroller’s
other analog features. They may be used to provide
analog signal conditioning, either as stand-alone
devices or in addition to other analog peripherals.
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information, refer to the
“PIC24F Family Reference Manual”,
Section 61. “Operational Amplifier
(Op Amp)” (DS30505). Device-specific
information in this data sheet supersedes
the information in the “PIC24F Family
Reference Manual”.
FIGURE 21-1:
The two op amps are functionally identical; the block
diagram for a single amplifier is shown in Figure 21-1.
Each op amp has these features:
• Internal unity-gain buffer option
• Multiple input options each on the inverting and
non-inverting amplifier inputs
• Rail-to-rail input and output capabilities
SINGLE OPERATIONAL AMPLIFIER BLOCK DIAGRAM
NINSEL<2:0>
AVSS
OAxINB
OAxIND
AMPSLP
AMPSIDL
AVSS
–
OAxINA
OAxINC
+
DACx Out
OAxOUT
CTMU/A/D
PINSEL<2:0>
SPDSEL
AMPEN
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 233
PIC24FV16KM204 FAMILY
REGISTER 21-1:
AMPxCON: OP AMP x CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
AMPEN
—
AMPSIDL
AMPSLP
—
—
—
—
bit 15
bit 8
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SPDSEL
—
NINSEL2
NINSEL1
NINSEL0
PINSEL2
PINSEL1
PINSEL0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
AMPEN: Op Amp Control Module Enable bit
1 = Module is enabled
0 = Module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
AMPSIDL: Op Amp Peripheral Stop in Idle Mode bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12
AMPSLP: Op Amp Peripheral Enabled in Sleep Mode bit
1 = Continues module operation when device enters Sleep mode
0 = Discontinues module operation in Sleep mode
bit 11-8
Unimplemented: Read as ‘0’
bit 7
SPDSEL: Op Amp Power/Speed Select bit
1 = Higher power and bandwidth (faster response time)
0 = Lower power and bandwidth (slower response time)
bit 6
Unimplemented: Read as ‘0’
bit 5-3
NINSEL<2:0>: Negative Op Amp Input Select bits
111 = Reserved; do not use
110 = Reserved; do not use
101 = Op amp negative input connected to the op amp output (voltage follower)
100 = Reserved; do not use
011 = Reserved; do not use
010 = Op amp negative input connected to the OAxIND pin
001 = Op amp negative input connected to the OAxINB pin
000 = Op amp negative input connected to AVSS
bit 2-0
PINSEL<2:0>: Positive Op Amp Input Select bits
111 = Op amp positive input connected to the output of the A/D input multiplexer
110 = Reserved; do not use
101 = Op amp positive input connected to the DAC1 output for OA1 (DAC2 output for OA2)
100 = Reserved; do not use
011 = Reserved; do not use
010 = Op amp positive input connected to the OAxINC pin
001 = Op amp positive input connected to the OAxINA pin
000 = Op amp positive input connected to AVSS
DS33030A-page 234
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
22.0
COMPARATOR MODULE
Note:
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on the
Comparator module, refer to the “PIC24F
Family Reference Manual”, Section 46.
“Scalable
Comparator
Module”
(DS39734).
The comparator module provides three dual input
comparators. The inputs to the comparator can be
configured to use any one of four external analog
inputs, as well as a voltage reference input from either
the internal band gap reference, divided by 2 (VBG/2),
or the comparator voltage reference generator.
FIGURE 22-1:
The comparator outputs may be directly connected to
the CxOUT pins. When the respective COE bit equals
‘1’, the I/O pad logic makes the unsynchronized output
of the comparator available on the pin.
A simplified block diagram of the module is shown in
Figure 22-1. Diagrams of the possible individual
comparator configurations are shown in Figure 22-2.
Each comparator has its own control register,
CMxCON (Register 22-1), for enabling and configuring
its operation. The output and event status of all three
comparators is provided in the CMSTAT register
(Register 22-2).
COMPARATOR MODULE BLOCK DIAGRAM
CCH<1:0>
CREF<1:0>
EVPOL<1:0>
CXINB
CXINC
CXIND
Input
Select
Logic
CPOL
VINVIN+
Trigger/Interrupt
Logic
CEVT
COE
C1
COUT
VBG/2
C1OUT
Pin
EVPOL<1:0>
Trigger/Interrupt
Logic
CPOL
CEVT
COE
VINVIN+
C2
COUT
C2OUT
Pin
EVPOL<1:0>
CPOL
CXINA
CVREF
Trigger/Interrupt
Logic
VINVIN+
CEVT
COE
C3
COUT
 2013 Microchip Technology Inc.
Advance Information
C3OUT
Pin
DS33030A-page 235
PIC24FV16KM204 FAMILY
FIGURE 22-2:
INDIVIDUAL COMPARATOR CONFIGURATIONS
Comparator Off
CON = 0, CREF<1:0> = xx, CCH<1:0> = xx
VIN-
COE
–
VIN+
Cx
Off (Read as ‘0’)
Comparator CxINB > CxINA Compare
CON = 1, CREF<1:0> = 00, CCH<1:0> = 00
CXINB
CXINA
VIN-
Comparator CxINC > CxINA Compare
CON = 1, CREF<1:0> = 00, CCH<1:0> = 01
COE
–
VIN+
CXINC
Cx
CxOUT
Pin
CXINA
VIN-
COE
–
VIN+
VBG/2
Cx
CxOUT
Pin
Comparator CxINB > CVREF Compare
CON = 1, CREF<1:0> = 01, CCH<1:0> = 00
CXINB
CVREF
VINVIN+
DAC1OUT
DS33030A-page 236
VINVIN+
CXINA
COE
–
CXINC
Cx
CxOUT
Pin
CVREF
VIN+
Cx
CxOUT
Pin
VIN-
COE
–
VIN+
Cx
CxOUT
Pin
VIN-
COE
–
VIN+
Cx
CxOUT
Pin
Comparator VBG > CVREF Compare
CON = 1, CREF<1:0> = 11, CCH<1:0> = 11
COE
–
COE
–
Comparator CxINC > CVREF Compare
CON = 1, CREF<1:0> = 01, CCH<1:0> = 01
Comparator CxIND > CVREF Compare
CON = 1, CREF<1:0> = 10, CCH<1:0> = 10
CXIND
CXINA
VIN-
Comparator VBG > CxINA Compare
CON = 1, CREF<1:0> = 00, CCH<1:0> = 11
Comparator CxIND > CxINA Compare
CON = 1, CREF<1:0> = 00, CCH<1:0> = 10
CXIND
CxOUT
Pin
VBG/2
Cx
CxOUT
Pin
DAC2OUT
Advance Information
VINVIN+
COE
–
Cx
CxOUT
Pin
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 22-1:
CMxCON: COMPARATOR x CONTROL REGISTERS
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
R/W-0
R-0
CON
COE
CPOL
CLPWR
—
—
CEVT
COUT
bit 15
bit 8
R/W-0
R/W-0
U-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
EVPOL1
EVPOL0
—
CREF1
CREF0
—
CCH1
CCH0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CON: Comparator Enable bit
1 = Comparator is enabled
0 = Comparator is disabled
bit 14
COE: Comparator Output Enable bit
1 = Comparator output is present on the CxOUT pin
0 = Comparator output is internal only
bit 13
CPOL: Comparator Output Polarity Select bit
1 = Comparator output is inverted
0 = Comparator output is not inverted
bit 12
CLPWR: Comparator Low-Power Mode Select bit
1 = Comparator operates in Low-Power mode
0 = Comparator does not operate in Low-Power mode
bit 11-10
Unimplemented: Read as ‘0’
bit 9
CEVT: Comparator Event bit
1 = Comparator event, defined by EVPOL<1:0>, has occurred; subsequent Triggers and interrupts are
disabled until the bit is cleared
0 = Comparator event has not occurred
bit 8
COUT: Comparator Output bit
When CPOL = 0:
1 = VIN+ > VIN0 = VIN+ < VINWhen CPOL = 1:
1 = VIN+ < VIN0 = VIN+ > VIN-
bit 7-6
EVPOL<1:0>: Trigger/Event/Interrupt Polarity Select bits
11 = Trigger/event/interrupt is generated on any change of the comparator output (while CEVT = 0)
10 = Trigger/event/interrupt is generated on the transition of the comparator output:
If CPOL = 0 (non-inverted polarity):
High-to-low transition only.
If CPOL = 1 (inverted polarity):
Low-to-high transition only.
01 = Trigger/event/interrupt is generated on the transition of the comparator output
If CPOL = 0 (non-inverted polarity):
Low-to-high transition only.
If CPOL = 1 (inverted polarity):
High-to-low transition only.
00 = Trigger/event/interrupt generation is disabled
bit 5
Unimplemented: Read as ‘0’
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 237
PIC24FV16KM204 FAMILY
REGISTER 22-1:
CMxCON: COMPARATOR x CONTROL REGISTERS (CONTINUED)
bit 4-3
CREF<1:0>: Comparator Reference Select bits (non-inverting input)
11 = Non-inverting input connects to the DAC2 output
10 = Non-inverting input connects to the DAC1 output
01 = Non-inverting input connects to the internal CVREF voltage
00 = Non-inverting input connects to the CxINA pin
bit 2
Unimplemented: Read as ‘0’
bit 1-0
CCH<1:0>: Comparator Channel Select bits
11 = Inverting input of the comparator connects to VBG
10 = Inverting input of the comparator connects to the CxIND pin
01 = Inverting input of the comparator connects to the CxINC pin
00 = Inverting input of the comparator connects to the CxINB pin
REGISTER 22-2:
CMSTAT: COMPARATOR MODULE STATUS REGISTER
R/W-0
U-0
U-0
U-0
U-0
R-0, HSC
R-0, HSC
R-0, HSC
CMIDL
—
—
—
—
C3EVT
C2EVT
C1EVT
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R-0, HSC
R-0, HSC
R-0, HSC
—
—
—
—
—
C3OUT
C2OUT
C1OUT
bit 7
bit 0
Legend:
HSC = Hardware Settable/Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CMIDL: Comparator Stop in Idle Mode bit
1 = Comparator interrupts are disabled in Idle mode; enabled comparators remain operational
0 = Continues operation of all enabled comparators in Idle mode
bit 14-11
Unimplemented: Read as ‘0’
bit 10
C3EVT: Comparator 3 Event Status bit (read-only)
Shows the current event status of Comparator 3 (CM3CON<9>).
bit 9
C2EVT: Comparator 2 Event Status bit (read-only)
Shows the current event status of Comparator 2 (CM2CON<9>).
bit 8
C1EVT: Comparator 1 Event Status bit (read-only)
Shows the current event status of Comparator 1 (CM1CON<9>).
bit 7-3
Unimplemented: Read as ‘0’
bit 2
C3OUT: Comparator 3 Output Status bit (read-only)
Shows the current output of Comparator 3 (CM3CON<8>).
bit 1
C2OUT: Comparator 2 Output Status bit (read-only)
Shows the current output of Comparator 2 (CM2CON<8>).
bit 0
C1OUT: Comparator 1 Output Status bit (read-only)
Shows the current output of Comparator 1 (CM1CON<8>).
DS33030A-page 238
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
23.0
Note:
COMPARATOR VOLTAGE
REFERENCE
23.1
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on the
Comparator Voltage Reference, refer to
the “PIC24F Family Reference Manual”,
Section 20. “Comparator Voltage
Reference Module” (DS39709).
Configuring the Comparator
Voltage Reference
The comparator voltage reference module is controlled
through the CVRCON register (Register 23-1). The
comparator voltage reference provides a range of
output voltages with 32 distinct levels.
The comparator voltage reference supply voltage can
come from either VDD and VSS, or the external VREF+
and VREF-. The voltage source is selected by the
CVRSS bit (CVRCON<5>).
The settling time of the comparator voltage reference
must be considered when changing the CVREF output.
FIGURE 23-1:
COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM
VREF+
AVDD
CVRSS = 1
CVRSS = 0
CVR<3:0>
R
CVREN
R
R
32 Steps
R
32-to-1 MUX
R
CVREF
R
R
VREF-
CVRSS = 1
CVRSS = 0
AVSS
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 239
PIC24FV16KM204 FAMILY
REGISTER 23-1:
CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CVREN
CVROE
CVRSS
CVR4
CVR3
CVR2
CVR1
CVR0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
Unimplemented: Read as ‘0’
bit 7
CVREN: Comparator Voltage Reference Enable bit
1 = CVREF circuit is powered on
0 = CVREF circuit is powered down
bit 6
CVROE: Comparator VREF Output Enable bit
1 = CVREF voltage level is output on the CVREF pin
0 = CVREF voltage level is disconnected from the CVREF pin
bit 5
CVRSS: Comparator VREF Source Selection bit
1 = Comparator reference source, CVRSRC = VREF+ – VREF0 = Comparator reference source, CVRSRC = AVDD – AVSS
bit 4-0
CVR<4:0>: Comparator VREF Value Selection 0 ≤ CVR<4:0> ≤ 31 bits
When CVRSS = 1:
CVREF = (VREF-) + (CVR<4:0>/32) • (VREF+ – VREF-)
When CVRSS = 0:
CVREF = (AVSS) + (CVR<4:0>/32) • (AVDD – AVSS)
DS33030A-page 240
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
24.0
Note:
CHARGE TIME
MEASUREMENT UNIT (CTMU)
This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on the
Charge Measurement Unit, refer to the
“PIC24F Family Reference Manual”,
Section 53. “Charge Time Measurement
Unit (CTMU) with Threshold Detect”
(DS39743).
The Charge Time Measurement Unit (CTMU) is a
flexible analog module that provides charge
measurement, accurate differential time measurement
between pulse sources and asynchronous pulse
generation. Its key features include:
•
•
•
•
Thirteen external edge input Trigger sources
Polarity control for each edge source
Control of edge sequence
Control of response to edge levels or edge
transitions
• Time measurement resolution of one nanosecond
• Accurate current source suitable for capacitive
measurement
Together with other on-chip analog modules, the CTMU
can be used to precisely measure time, measure
capacitance, measure relative changes in capacitance
or generate output pulses that are independent of the
system clock. The CTMU module is ideal for interfacing
with capacitive-based touch sensors.
24.1
Measuring Capacitance
The CTMU module measures capacitance by
generating an output pulse, with a width equal to the
time between edge events, on two separate input
channels. The pulse edge events to both input
channels can be selected from several internal
peripheral modules (OC1, Timer1, any input capture or
comparator module) and up to 13 external pins
(CTED1 through CTED13). This pulse is used with the
module’s precision current source to calculate
capacitance according to the relationship:
EQUATION 24-1:
dV
I = C  ------dT
For capacitance measurements, the A/D Converter
samples an external capacitor (CAPP) on one of its
input channels after the CTMU output’s pulse. A precision resistor (RPR) provides current source calibration
on a second A/D channel. After the pulse ends, the
converter determines the voltage on the capacitor. The
actual calculation of capacitance is performed in
software by the application.
Figure 24-1 illustrates the external connections used
for capacitance measurements, and how the CTMU
and A/D modules are related in this application. This
example also shows the edge events coming from
Timer1, but other configurations using external edge
sources are possible. A detailed discussion on measuring capacitance and time with the CTMU module is
provided in the “PIC24F Family Reference Manual”.
The CTMU is controlled through three registers:
CTMUCON1,
CTMUCON2
and
CTMUICON.
CTMUCON1 enables the module and controls the mode
of operation of the CTMU, as well as controlling edge
sequencing. CTMUCON2 controls edge source selection and edge source polarity selection. The CTMUICON
register selects the current range of current source and
trims the current.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 241
PIC24FV16KM204 FAMILY
FIGURE 24-1:
TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR
CAPACITANCE MEASUREMENT
PIC24F Device
Timer1
CTMU
EDG1STAT
Current Source
EDG2STAT
Output Pulse
A/D Converter
ANx
ANy
CAPP
24.2
RPR
Measuring Time
Time measurements on the pulse width can be similarly
performed using the A/D module’s internal capacitor
(CAD) and a precision resistor for current calibration.
Figure 24-2 displays the external connections used for
FIGURE 24-2:
time measurements, and how the CTMU and A/D
modules are related in this application. This example
also shows both edge events coming from the external
CTEDx pins, but other configurations using internal
edge sources are possible.
TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR
TIME MEASUREMENT
PIC24F Device
CTMU
CTEDX
EDG1STAT
CTEDX
EDG2STAT
Current Source
Output Pulse
ANx
A/D Converter
CAD
RPR
DS33030A-page 242
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
24.3
Pulse Generation and Delay
When the voltage on CDELAY equals CVREF, CTPLS
goes low. With Comparator 2 configured as the second
edge, this stops the CTMU from charging. In this state
event, the CTMU automatically connects to ground.
The IDISSEN bit doesn’t need to be set and cleared
before the next CTPLS cycle.
The CTMU module can also generate an output pulse
with edges that are not synchronous with the device’s
system clock. More specifically, it can generate a pulse
with a programmable delay from an edge event input to
the module.
Figure 24-3 illustrates the external connections for
pulse generation, as well as the relationship of the
different analog modules required. While CTED1 is
shown as the input pulse source, other options are
available. A detailed discussion on pulse generation
with the CTMU module is provided in the “PIC24F
Family Reference Manual”.
When the module is configured for pulse generation
delay by setting the TGEN bit (CTMUCON1L<12>), the
internal current source is connected to the B input of
Comparator 2. A capacitor (CDELAY) is connected to
the Comparator 2 pin, C2INB, and the Comparator
Voltage Reference, CVREF, is connected to C2INA.
CVREF is then configured for a specific trip point. The
module begins to charge CDELAY when an edge event
is detected. While CVREF is greater than the voltage on
CDELAY, CTPLS is high.
FIGURE 24-3:
TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR PULSE
DELAY GENERATION
PIC24F Device
CTMU
VDD
CTED1
EDG1STAT
D
Q
CK
Q
CTPLS
EDG1STAT
EDG2STAT
R
Current
Source
Comparator
–
C2
C2INB
CDELAY
 2013 Microchip Technology Inc.
EDG2STAT
CVREF
Advance Information
DS33030A-page 243
PIC24FV16KM204 FAMILY
REGISTER 24-1:
CTMUCON1L: CTMU CONTROL 1 LOW REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CTMUEN
—
CTMUSIDL
TGEN
EDGEN
EDGSEQEN
IDISSEN
CTTRIG
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ITRIM5
ITRIM4
ITRIM3
ITRIM2
ITRIM1
ITRIM0
IRNG1
IRNG0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
CTMUSIDL: CTMU Stop in Idle Mode bit
1 = Discontinues module operation when device enters Idle mode
0 = Continues module operation in Idle mode
bit 12
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
bit 11
EDGEN: Edge Enable bit
1 = Edges are not blocked
0 = Edges are blocked
bit 10
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
bit 9
IDISSEN: Analog Current Source Control bit
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
bit 8
CTTRIG: Trigger Control bit
1 = Trigger output is enabled
0 = Trigger output is disabled
bit 7-2
ITRIM<5:0>: Current Source Trim bits
011111 = Maximum positive change from nominal current
011110
.
.
.
000001 = Minimum positive change from nominal current
000000 = Nominal current output specified by IRNG<1:0>
111111 = Minimum negative change from nominal current
.
.
.
100010
100001 = Maximum negative change from nominal current
DS33030A-page 244
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 24-1:
bit 1-0
CTMUCON1L: CTMU CONTROL 1 LOW REGISTER (CONTINUED)
IRNG<1:0>: Current Source Range Select bits
11 = 100 × Base Current
10 = 10 × Base Current
01 = Base Current Level (0.55 µA nominal)
00 = 1000 × Base Current
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 245
PIC24FV16KM204 FAMILY
REGISTER 24-2:
CTMUCON1H: CTMU CONTROL 1 HIGH REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
EDG1MOD
EDG1POL
EDG1SEL3
EDG1SEL2
EDG1SEL1
EDG1SEL0
EDG2STAT
EDG1STAT
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
EDG2MOD
EDG2POL
EDG2SEL3
EDG2SEL2
EDG2SEL1
EDG2SEL0
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
EDG1MOD: Edge 1 Edge-Sensitive Select bit
1 = Input is edge-sensitive
0 = Input is level-sensitive
bit 14
EDG1POL: Edge 1 Polarity Select bit
1 = Edge 1 is programmed for a positive edge response
0 = Edge 1 is programmed for a negative edge response
bit 13-10
EDG1SEL<3:0>: Edge 1 Source Select bits
1111 = Edge 1 source is the Comparator 3 output
1110 = Edge 1 source is the Comparator 2 output
1101 = Edge 1 source is the Comparator 1 output
1100 = Edge 1 source is CLC2
1011 = Edge 1 source is CLD1
1010 = Edge 1 source is MCCP2
1001 = Edge 1 source is CTED8(1)
1000 = Edge 1 source is CTED7(1)
0111 = Edge 1 source is CTED6
0110 = Edge 1 source is CTED5
0101 = Edge 1 source is CTED4
0100 = Edge 1 source is CTED3(2)
0011 = Edge 1 source is CTED1
0010 = Edge 1 source is CTED2
0001 = Edge 1 source is MCCP1
0000 = Edge 1 source is Timer1
bit 9
EDG2STAT: Edge 2 Status bit
Indicates the status of Edge 2 and can be written to control the current source.
1 = Edge 2 has occurred
0 = Edge 2 has not occurred
bit 8
EDG1STAT: Edge 1 Status bit
Indicates the status of Edge 1 and can be written to control the current source.
1 = Edge 1 has occurred
0 = Edge 1 has not occurred
bit 7
EDG2MOD: Edge 2 Edge-Sensitive Select bit
1 = Input is edge-sensitive
0 = Input is level-sensitive
Note 1:
2:
Edge sources, CTED7 and CTED8, are not available on 28-pin or 20-pin devices.
Edge sources, CTED3, CTED9 and CTED11, are not available on 20-pin devices.
DS33030A-page 246
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 24-2:
CTMUCON1H: CTMU CONTROL 1 HIGH REGISTER (CONTINUED)
bit 6
EDG2POL: Edge 2 Polarity Select bit
1 = Edge 2 is programmed for a positive edge
0 = Edge 2 is programmed for a negative edge
bit 5-2
EDG2SEL<3:0>: Edge 2 Source Select bits
1111 = Edge 2 source is the Comparator 3 output
1110 = Edge 2 source is the Comparator 2 output
1101 = Edge 2 source is the Comparator 1 output
1100 = Unimplemented; do not use
1011 = Edge 2 source is CLC1
1010 = Edge 2 source is MCCP2
1001 = Unimplemented: do not use
1000 = Edge 2 source is CTED13
0111 = Edge 2 source is CTED12
0110 = Edge 2 source is CTED11(2)
0101 = Edge 2 source is CTED10
0100 = Edge 2 source is CTED9(2)
0011 = Edge 2 source is CTED1
0010 = Edge 2 source is CTED2
0001 = Edge 2 source is MCCP1
0000 = Edge 2 source is Timer1
bit 1-0
Unimplemented: Read as ‘0’
Note 1:
2:
Edge sources, CTED7 and CTED8, are not available on 28-pin or 20-pin devices.
Edge sources, CTED3, CTED9 and CTED11, are not available on 20-pin devices.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 247
PIC24FV16KM204 FAMILY
REGISTER 24-3:
CTMUCON2L: CTMU CONTROL 2 LOW REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
—
—
—
IRSTEN
—
DISCHS2
DISCHS1
DISCHS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-5
Unimplemented: Read as ‘0’
bit 4
IRSTEN: CTMU Current Source Reset Enable bit
1 = Signal selected by the DISCHS<2:0> bits or the IDISSEN control bit will reset the CTMU edge
detect logic
0 = CTMU edge detect logic will not occur
bit 3
Unimplemented: Read as ‘0’
bit 2-0
DISCHS<2:0>: Discharge Source Select bits
111 = CLC2 output
110 = CLC1 output
101 = Reserved; do not use.
100 = A/D end of conversion signal
011 = SCCP5 auxiliary output
110 = MCCP2 auxiliary output
001 = MCCP1 auxiliary output
000 = No discharge source selected, use the IDISSEN bit
DS33030A-page 248
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
25.0
SPECIAL FEATURES
Note:
25.1
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference source. For more information on the
Watchdog Timer, High-Level Device Integration and Programming Diagnostics,
refer to the individual sections of the
“PIC24F Family Reference Manual”
provided below:
• Section 9. “Watchdog Timer (WDT)”
(DS39697)
• Section 33. “Programming and
Diagnostics” (DS39716)
PIC24FV16KM204 family devices include several
features intended to maximize application flexibility and
reliability, and minimize cost through elimination of
external components. These are:
•
•
•
•
•
Flexible Configuration
Watchdog Timer (WDT)
Code Protection
In-Circuit Serial Programming™ (ICSP™)
In-Circuit Emulation
REGISTER 25-1:
Configuration Bits
The Configuration bits can be programmed (read as
‘0’), or left unprogrammed (read as ‘1’), to select various device configurations. These bits are mapped,
starting at program memory location, F80000h. A complete list of Configuration register locations is provided
in Table 25-1. A detailed explanation of the various bit
functions is provided in Register 25-1 through
Register 25-9.
The address, F80000h, is beyond the user program
memory space. In fact, it belongs to the configuration
memory space (800000h-FFFFFFh), which can only be
accessed using Table Reads and Table Writes.
TABLE 25-1:
CONFIGURATION REGISTERS
LOCATIONS
Configuration
Register
Address
FBS
F80000
FGS
F80004
FOSCSEL
F80006
FOSC
F80008
FWDT
F8000A
FPOR
F8000C
FICD
F8000E
FBS: BOOT SEGMENT CONFIGURATION REGISTER
U-0
U-0
U-0
U-0
R/W-1
R/W-1
R/W-1
R/W-1
—
—
—
—
BSS2
BSS1
BSS0
BWRP
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-4
Unimplemented: Read as ‘0’
bit 3-1
BSS<2:0>: Boot Segment Program Flash Code Protection bits
111 = No boot program Flash segment
011 = Reserved
110 = Standard security, boot program Flash segment starts at 200h, ends at 000AFEh
010 = High-security boot program Flash segment starts at 200h, ends at 000AFEh
101 = Standard security, boot program Flash segment starts at 200h, ends at 0015FEh(1)
001 = High-security, boot program Flash segment starts at 200h, ends at 0015FEh(1)
100 = Reserved
000 = Reserved
bit 0
BWRP: Boot Segment Program Flash Write Protection bit
1 = Boot segment may be written
0 = Boot segment is write-protected
Note 1:
This selection should not be used in PIC24FV08KMXXX devices.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 249
PIC24FV16KM204 FAMILY
REGISTER 25-2:
FGS: GENERAL SEGMENT CONFIGURATION REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
R/C-1
R/C-1
—
—
—
—
—
—
GCP
GWRP
bit 7
bit 0
Legend:
R = Readable bit
C = Clearable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-2
Unimplemented: Read as ‘0’
bit 1
GCP: General Segment Code Flash Code Protection bit
1 = No protection
0 = Standard security is enabled
bit 0
GWRP: General Segment Code Flash Write Protection bit
1 = General segment may be written
0 = General segment is write-protected
REGISTER 25-3:
x = Bit is unknown
FOSCSEL: OSCILLATOR SELECTION CONFIGURATION REGISTER
R/P-1
R/P-1
R/P-1
U-0
U-0
R/P-1
R/P-1
R/P-1
IESO
LPRCSEL
SOSCSRC
—
—
FNOSC2
FNOSC1
FNOSC0
bit 7
bit 0
Legend:
R = Readable bit
P = Programmable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
IESO: Internal External Switchover bit
1 = Internal External Switchover mode is enabled (Two-Speed Start-up is enabled)
0 = Internal External Switchover mode is disabled (Two-Speed Start-up is disabled)
bit 6
LPRCSEL: Internal LPRC Oscillator Power Select bit
1 = High-Power/High-Accuracy mode
0 = Low-Power/Low-Accuracy mode
bit 5
SOSCSRC: Secondary Oscillator Clock Source Configuration bit
1 = SOSC analog crystal function is available on the SOSCI/SOSCO pins
0 = SOSC crystal is disabled; digital SCLKI function is selected on the SOSCO pin
bit 4-3
Unimplemented: Read as ‘0’
bit 2-0
FNOSC<2:0>: Oscillator Selection bits
000 = Fast RC Oscillator (FRC)
001 = Fast RC Oscillator with Divide-by-N with PLL module (FRCDIV+PLL)
010 = Primary Oscillator (XT, HS, EC)
011 = Primary Oscillator with PLL module (HS+PLL, EC+PLL)
100 = Secondary Oscillator (SOSC)
101 = Low-Power RC Oscillator (LPRC)
110 = 500 kHz Low-Power FRC Oscillator with Divide-by-N (LPFRCDIV)
111 = 8 MHz FRC Oscillator with Divide-by-N (FRCDIV)
DS33030A-page 250
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 25-4:
FOSC: OSCILLATOR CONFIGURATION REGISTER
R/P-1
R/P-1
FCKSM1
FCKSM0
R/P-1
R/P-1
R/P-1
R/P-1
SOSCSEL POSCFREQ1 POSCFREQ0 OSCIOFNC
R/P-1
R/P-1
POSCMD1
POSCMD0
bit 7
bit 0
Legend:
R = Readable bit
P = Programmable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-6
FCKSM<1:0>: Clock Switching and Fail-Safe Clock Monitor Selection Configuration bits
1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled
01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled
00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled
bit 5
SOSCSEL: Secondary Oscillator Power Selection Configuration bit
1 = Secondary oscillator is configured for high-power operation
0 = Secondary oscillator is configured for low-power operation
bit 4-3
POSCFREQ<1:0>: Primary Oscillator Frequency Range Configuration bits
11 = Primary oscillator/external clock input frequency is greater than 8 MHz
10 = Primary oscillator/external clock input frequency is between 100 kHz and 8 MHz
01 = Primary oscillator/external clock input frequency is less than 100 kHz
00 = Reserved; do not use
bit 2
OSCIOFNC: CLKO Enable Configuration bit
1 = CLKO output signal is active on the OSCO pin; primary oscillator must be disabled or configured
for the External Clock mode (EC) for the CLKO to be active (POSCMD<1:0> = 11 or 00)
0 = CLKO output is disabled
bit 1-0
POSCMD<1:0>: Primary Oscillator Configuration bits
11 = Primary Oscillator mode is disabled
10 = HS Oscillator mode is selected
01 = XT Oscillator mode is selected
00 = External Clock mode is selected
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 251
PIC24FV16KM204 FAMILY
REGISTER 25-5:
FWDT: WATCHDOG TIMER CONFIGURATION REGISTER
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
FWDTEN1
WINDIS
FWDTEN0
FWPSA
WDTPS3
WDTPS2
WDTPS1
WDTPS0
bit 7
bit 0
Legend:
R = Readable bit
P = Programmable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7,5
FWDTEN<1:0>: Watchdog Timer Enable bits
11 = WDT is enabled in hardware
10 = WDT is controlled with the SWDTEN bit setting
01 = WDT is enabled only while the device is active; WDT is disabled in Sleep; SWDTEN bit is disabled
00 = WDT is disabled in hardware; SWDTEN bit is disabled
bit 6
WINDIS: Windowed Watchdog Timer Disable bit
1 = Standard WDT is selected; windowed WDT is disabled
0 = Windowed WDT is enabled; note that executing a CLRWDT instruction while the WDT is disabled in
hardware and software (FWDTEN<1:0> = 00 and SWDTEN (RCON<5>) = 0) will not cause a
device Reset
bit 4
FWPSA: WDT Prescaler bit
1 = WDT prescaler ratio of 1:128
0 = WDT prescaler ratio of 1:32
bit 3-0
WDTPS<3:0>: Watchdog Timer Postscale Select bits
1111 = 1:32,768
1110 = 1:16,384
1101 = 1:8,192
1100 = 1:4,096
1011 = 1:2,048
1010 = 1:1,024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
DS33030A-page 252
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 25-6:
FPOR: RESET CONFIGURATION REGISTER
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
MCLRE(2)
BORV1(3)
BORV0(3)
I2C1SEL(1)
PWRTEN
RETCFG(1)
BOREN1
BOREN0
bit 7
bit 0
Legend:
R = Readable bit
P = Programmable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
MCLRE: MCLR Pin Enable bit(2)
1 = MCLR pin is enabled; RA5 input pin is disabled
0 = RA5 input pin is enabled; MCLR is disabled
bit 6-5
BORV<1:0>: Brown-out Reset Enable bits(3)
11 = Brown-out Reset is set to the lowest voltage
10 = Brown-out Reset is set to the middle voltage
01 = Brown-out Reset is set to the highest voltage
00 = Downside protection on POR is enabled – Low-Power BOR (LPBOR) is selected
bit 4
I2C1SEL: Alternate I2C1 Pin Mapping bit(1)
1 = Default location for SCL1/SDA1 pins
0 = Alternate location for SCL1/SDA1 pins
bit 3
PWRTEN: Power-up Timer Enable bit
1 = PWRT is enabled
0 = PWRT is disabled
bit 2
RETCFG: Retention Regulator Configuration bit(1)
1 = Low-voltage regulator is not available
0 = Low-voltage regulator is available and controlled by the RETEN bit (RCON<12>) during Sleep
bit 1-0
BOREN<1:0>: Brown-out Reset Enable bits
11 = Brown-out Reset is enabled in hardware; SBOREN bit is disabled
10 = Brown-out Reset is enabled only while device is active and disabled in Sleep; SBOREN bit is disabled
01 = Brown-out Reset is controlled with the SBOREN bit setting
00 = Brown-out Reset is disabled in hardware; SBOREN bit is disabled
Note 1:
2:
3:
This setting only applies to the “FV” devices. This bit is reserved and should be maintained as ‘1’ on “F”
devices.
The MCLRE fuse can only be changed when using the VPP-based ICSP™ mode entry. This prevents a user
from accidentally locking out the device from the low-voltage test entry.
Refer to Section 29.0 “Electrical Characteristics” for BOR voltages.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 253
PIC24FV16KM204 FAMILY
REGISTER 25-7:
FICD: IN-CIRCUIT DEBUGGER CONFIGURATION REGISTER
R/P-1
U-0
U-0
U-0
U-0
U-0
R/P-1
R/P-1
DEBUG
—
—
—
—
—
FICD1
FICD0
bit 7
bit 0
Legend:
R = Readable bit
P = Programmable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
DEBUG: Background Debugger Enable bit
1 = Background debugger is disabled
0 = Background debugger functions are enabled
bit 6-2
Unimplemented: Read as ‘0’
bit 1-0
FICD<1:0:>: ICD Pin Select bits
11 = PGEC1/PGED1 are used for programming and debugging the device
10 = PGEC2/PGED2 are used for programming and debugging the device
01 = PGEC3/PGED3 are used for programming and debugging the device
00 = Reserved; do not use
DS33030A-page 254
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
REGISTER 25-8:
DEVID: DEVICE ID REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 23
bit 16
R
R
R
R
R
R
R
R
FAMID7
FAMID6
FAMID5
FAMID4
FAMID3
FAMID2
FAMID1
FAMID0
bit 15
bit 8
R
R
R
R
R
R
R
R
DEV7
DEV6
DEV5
DEV4
DEV3
DEV2
DEV1
DEV0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-16
Unimplemented: Read as ‘0’
bit 15-8
FAMID<7:0>: Device Family Identifier bits
01000101 = PIC24FV16KM204 family
bit 7-0
DEV<7:0>: Individual Device Identifier bits
00011111 = PIC24FV16KM204
00011011 = PIC24FV16KM202
00010111 = PIC24FV08KM204
00010011 = PIC24FV08KM202
00001111 = PIC24FV16KM104
00001011 = PIC24FV16KM102
00000011 = PIC24FV08KM102
00000001 = PIC24FV08KM101
x = Bit is unknown
00011110 = PIC24F16KM204
00011010 = PIC24F16KM202
00010110 = PIC24F08KM204
00010010 = PIC24F08KM202
00001110 = PIC24F16KM104
00001010 = PIC24F16KM102
00000010 = PIC24F08KM102
00000000 = PIC24F08KM101
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 255
PIC24FV16KM204 FAMILY
REGISTER 25-9:
DEVREV: DEVICE REVISION REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 23
bit 16
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R
R
R
R
—
—
—
—
REV3
REV2
REV1
REV0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-4
Unimplemented: Read as ‘0’
bit 3-0
REV<3:0>: Minor Revision Identifier bits
DS33030A-page 256
Advance Information
x = Bit is unknown
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
25.2
On-Chip Voltage Regulator
All of the PIC24FV16KM204 family devices power their
core digital logic at a nominal 3.0V. This may create an
issue for designs that are required to operate at a
higher typical voltage, as high as 5.0V. To simplify system design, all devices in the “FV” family incorporate an
on-chip regulator that allows the device core to run at
3.0V, while the I/O is powered by VDD at a higher
voltage.
The regulator is always enabled and provides power to
the core from the other VDD pins. A low-ESR capacitor
(such as ceramic) must be connected to the VCAP pin
(Figure 25-1). This helps to maintain the stability of the
regulator. The recommended value for the filter capacitor is provided in Section 29.1 “DC Characteristics”
and discussed in detail in Section 2.0 “Guidelines for
Getting Started with 16-Bit Microcontrollers”.
In all of the “F” family of devices, the regulator is
disabled. Instead, the core logic is directly powered
from VDD. “F” devices operate at a lower range of VDD
voltage, from 1.8V-3.6V.
25.2.1
VOLTAGE REGULATOR TRACKING
MODE AND LOW-VOLTAGE
DETECTION
For all PIC24FV16KM204 devices, the on-chip regulator provides a constant voltage of 3.0V nominal to the
digital core logic. The regulator can provide this level
from a VDD of about 3.2V, all the way up to the device’s
VDDMAX. It does not have the capability to boost VDD
levels below 3.2V. In order to prevent “brown out” conditions when the voltage drops too low for the regulator,
the regulator enters Tracking mode. In Tracking mode,
the regulator output follows VDD with a typical voltage
drop of 150 mV.
When the device enters Tracking mode, it is no longer
possible to operate at full speed. To provide information
about when the device enters Tracking mode, the
on-chip High/Low-Voltage Detect (HLVD) module can be
used. The HLVD trip point should be configured so that
if VDD drops close to the minimum voltage for the operating frequency of the device, the HLVD interrupt will
occur, HLVDIF (IFS4<8>). This can be used to generate
an interrupt and put the application into a low-power
operational mode or trigger an orderly shutdown. Refer
to Section 27.1 “DC Characteristics” for the
specifications detailing the maximum operating speed
based on the applied VDD voltage.
 2013 Microchip Technology Inc.
FIGURE 25-1:
CONNECTIONS FOR THE
ON-CHIP REGULATOR
Regulator Enabled:(1)
5.0V
PIC24FV16KM
VDD
VCAP
CEFC
(10 F typ)
Note 1:
25.2.2
VSS
These are typical operating voltages. Refer to
Section 29.0 “Electrical Characteristics”
for the full operating ranges of VDD and
VDDCORE.
VOLTAGE REGULATOR START-UP
TIME
For PIC24FV16KM204 family devices, it takes a short
time, designated as TPM, for the regulator to generate
a stable output. During this time, code execution is disabled. TPM is applied every time the device resumes
operation after any power-down, including Sleep mode.
TPM is specified in Section 27.2 “AC Characteristics
and Timing Parameters”.
25.3
Watchdog Timer (WDT)
For the PIC24FV16KM204 family of devices, the WDT
is driven by the LPRC oscillator. When the WDT is
enabled, the clock source is also enabled.
The nominal WDT clock source from LPRC is 31 kHz.
This feeds a prescaler that can be configured for either
5-bit (divide-by-32) or 7-bit (divide-by-128) operation.
The prescaler is set by the FWPSA Configuration bit.
With a 31 kHz input, the prescaler yields a nominal
WDT time-out period (TWDT) of 1 ms in 5-bit mode or
4 ms in 7-bit mode.
A variable postscaler divides down the WDT prescaler
output and allows for a wide range of time-out periods.
The postscaler is controlled by the Configuration bits,
WDTPS<3:0> (FWDT<3:0>), which allow the selection
of a total of 16 settings, from 1:1 to 1:32,768. Using the
prescaler and postscaler time-out periods, ranges from
1 ms to 131 seconds can be achieved.
Advance Information
DS33030A-page 257
PIC24FV16KM204 FAMILY
The WDT, prescaler and postscaler are reset:
25.3.1
• On any device Reset
• On the completion of a clock switch, whether
invoked by software (i.e., setting the OSWEN bit
after changing the NOSCx bits) or by hardware
(i.e., Fail-Safe Clock Monitor)
• When a PWRSAV instruction is executed
(i.e., Sleep or Idle mode is entered)
• When the device exits Sleep or Idle mode to
resume normal operation
• By a CLRWDT instruction during normal execution
The Watchdog Timer has an optional Fixed Window
mode of operation. In this Windowed mode, CLRWDT
instructions can only reset the WDT during the last 1/4
of the programmed WDT period. A CLRWDT instruction
executed before that window causes a WDT Reset,
similar to a WDT time-out.
If the WDT is enabled in hardware (FWDTEN<1:0> = 11),
it will continue to run during Sleep or Idle modes. When
the WDT time-out occurs, the device will wake and code
execution will continue from where the PWRSAV
instruction was executed. The corresponding SLEEP or
IDLE bit (RCON<3:2>) will need to be cleared in software
after the device wakes up.
The WDT is enabled or disabled by the FWDTEN<1:0>
Configuration bits. When both of the FWDTEN<1:0>
Configuration bits are set, the WDT is always enabled.
Windowed WDT mode is enabled by programming the
Configuration bit, WINDIS (FWDT<6>), to ‘0’.
25.3.2
The WDT Flag bit, WDTO (RCON<4>), is not automatically cleared following a WDT time-out. To detect
subsequent WDT events, the flag must be cleared in
software.
Note:
The CLRWDT and PWRSAV instructions
clear the prescaler and postscaler counts
when executed.
FIGURE 25-2:
WINDOWED OPERATION
CONTROL REGISTER
The WDT can be optionally controlled in software when
the FWDTEN<1:0> Configuration bits have been programmed to ‘10’. The WDT is enabled in software by
setting the SWDTEN control bit (RCON<5>). The
SWDTEN control bit is cleared on any device Reset.
The software WDT option allows the user to enable the
WDT for critical code segments, and disable the WDT
during non-critical segments, for maximum power
savings. When the FWTEN<1:0> bits are set to ‘01’,
the WDT is only enabled in Run and Idle modes, and is
disabled in Sleep. Software control of the SWDTEN bit
(RCON<5>) is disabled with this setting.
WDT BLOCK DIAGRAM
SWDTEN
FWDTEN<1:0>
LPRC Control
WDTPS<3:0>
FWPSA
Prescaler
(5-Bit/7-Bit)
LPRC Input
31 kHz
Wake from Sleep
WDT
Counter
Postscaler
1:1 to 1:32.768
WDT Overflow
Reset
1 ms/4 ms
All Device Resets
Transition to
New Clock Source
Exit Sleep or
Idle Mode
CLRWDT Instr.
PWRSAV Instr.
Sleep or Idle Mode
DS33030A-page 258
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
25.4
Program Verification and
Code Protection
25.6
For all devices in the PIC24FV16KM204 family, code
protection for the boot segment is controlled by the
Configuration bit, BSS0, and the general segment by
the Configuration bit, GCP. These bits inhibit external
reads and writes to the program memory space This
has no direct effect in normal execution mode.
Write protection is controlled by bit, BWRP, for the boot
segment and bit, GWRP, for the general segment in the
Configuration Word. When these bits are programmed
to ‘0’, internal write and erase operations to program
memory are blocked.
25.5
In-Circuit Debugger
When MPLAB® ICD 3, MPLAB REAL ICE™ or PICkit™ 3
is selected as a debugger, the in-circuit debugging
functionality is enabled. This function allows simple
debugging functions when used with MPLAB IDE.
Debugging functionality is controlled through the PGECx
and PGEDx pins.
To use the in-circuit debugger function of the device,
the design must implement ICSP connections to
MCLR, VDD, VSS, PGECx, PGEDx and the pin pair. In
addition, when the feature is enabled, some of the
resources are not available for general use. These
resources include the first 80 bytes of data RAM and
two I/O pins.
In-Circuit Serial Programming
PIC24FV16KM204 family microcontrollers can be
serially programmed while in the end application circuit.
This is simply done with two lines for clock (PGECx) and
data (PGEDx), and three other lines for power, ground
and the programming voltage. This allows customers to
manufacture boards with unprogrammed devices and
then program the microcontroller just before shipping the
product. This also allows the most recent firmware or a
custom firmware to be programmed.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 259
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 260
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
26.0
DEVELOPMENT SUPPORT
The PIC® microcontrollers and dsPIC® Digital Signal
Controllers are supported with a full range of software
and hardware development tools:
• Integrated Development Environment
- MPLAB® IDE Software
• Compilers/Assemblers/Linkers
- MPLAB C Compiler for Various Device
Families
- HI-TECH C® for Various Device Families
- MPASMTM Assembler
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB Assembler/Linker/Librarian for
Various Device Families
• Simulators
- MPLAB SIM Software Simulator
• Emulators
- MPLAB REAL ICE™ In-Circuit Emulator
• In-Circuit Debuggers
- MPLAB ICD 3
- PICkit™ 3 Debug Express
• Device Programmers
- PICkit™ 2 Programmer
- MPLAB PM3 Device Programmer
• Low-Cost Demonstration/Development Boards,
Evaluation Kits, and Starter Kits
26.1
MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16/32-bit
microcontroller market. The MPLAB IDE is a Windows®
operating system-based application that contains:
• A single graphical interface to all debugging tools
- Simulator
- Programmer (sold separately)
- In-Circuit Emulator (sold separately)
- In-Circuit Debugger (sold separately)
• A full-featured editor with color-coded context
• A multiple project manager
• Customizable data windows with direct edit of
contents
• High-level source code debugging
• Mouse over variable inspection
• Drag and drop variables from source to watch
windows
• Extensive on-line help
• Integration of select third party tools, such as
IAR C Compilers
The MPLAB IDE allows you to:
• Edit your source files (either C or assembly)
• One-touch compile or assemble, and download to
emulator and simulator tools (automatically
updates all project information)
• Debug using:
- Source files (C or assembly)
- Mixed C and assembly
- Machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost-effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increased flexibility
and power.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 261
PIC24FV16KM204 FAMILY
26.2
MPLAB C Compilers for Various
Device Families
The MPLAB C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC18,
PIC24 and PIC32 families of microcontrollers and the
dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration
capabilities, superior code optimization and ease of
use.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
26.3
HI-TECH C for Various Device
Families
The HI-TECH C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC
family of microcontrollers and the dsPIC family of digital
signal controllers. These compilers provide powerful
integration capabilities, omniscient code generation
and ease of use.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple
platforms.
26.4
MPASM Assembler
The MPASM Assembler is a full-featured, universal
macro assembler for PIC10/12/16/18 MCUs.
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code and COFF files for
debugging.
The MPASM Assembler features include:
26.5
MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler and the
MPLAB C18 C Compiler. It can link relocatable objects
from precompiled libraries, using directives from a
linker script.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
26.6
MPLAB Assembler, Linker and
Librarian for Various Device
Families
MPLAB Assembler produces relocatable machine
code from symbolic assembly language for PIC24,
PIC32 and dsPIC devices. MPLAB C Compiler uses
the assembler to produce its object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
•
•
•
•
•
•
Support for the entire device instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
• Integration into MPLAB IDE projects
• User-defined macros to streamline
assembly code
• Conditional assembly for multi-purpose
source files
• Directives that allow complete control over the
assembly process
DS33030A-page 262
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
26.7
MPLAB SIM Software Simulator
The MPLAB SIM Software Simulator allows code
development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB SIM Software Simulator fully supports
symbolic debugging using the MPLAB C Compilers,
and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and
debug code outside of the hardware laboratory environment, making it an excellent, economical software
development tool.
26.8
MPLAB REAL ICE In-Circuit
Emulator System
MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC and MCU devices. It debugs and
programs PIC® Flash MCUs and dsPIC® Flash DSCs
with the easy-to-use, powerful graphical user interface of
the MPLAB Integrated Development Environment (IDE),
included with each kit.
The emulator is connected to the design engineer’s PC
using a high-speed USB 2.0 interface and is connected
to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal
(LVDS) interconnection (CAT5).
The emulator is field upgradable through future firmware
downloads in MPLAB IDE. In upcoming releases of
MPLAB IDE, new devices will be supported, and new
features will be added. MPLAB REAL ICE offers
significant advantages over competitive emulators
including low-cost, full-speed emulation, run-time
variable watches, trace analysis, complex breakpoints, a
ruggedized probe interface and long (up to three meters)
interconnection cables.
 2013 Microchip Technology Inc.
26.9
MPLAB ICD 3 In-Circuit Debugger
System
MPLAB ICD 3 In-Circuit Debugger System is Microchip’s most cost effective high-speed hardware
debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU)
devices. It debugs and programs PIC® Flash microcontrollers and dsPIC® DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated
Development Environment (IDE).
The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer’s PC using a high-speed
USB 2.0 interface and is connected to the target with a
connector compatible with the MPLAB ICD 2 or MPLAB
REAL ICE systems (RJ-11). MPLAB ICD 3 supports all
MPLAB ICD 2 headers.
26.10 PICkit 3 In-Circuit Debugger/
Programmer and
PICkit 3 Debug Express
The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a
most affordable price point using the powerful graphical
user interface of the MPLAB Integrated Development
Environment (IDE). The MPLAB PICkit 3 is connected
to the design engineer’s PC using a full speed USB
interface and can be connected to the target via an
Microchip debug (RJ-11) connector (compatible with
MPLAB ICD 3 and MPLAB REAL ICE). The connector
uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™.
The PICkit 3 Debug Express include the PICkit 3, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
Advance Information
DS33030A-page 263
PIC24FV16KM204 FAMILY
26.11 PICkit 2 Development
Programmer/Debugger and
PICkit 2 Debug Express
26.13 Demonstration/Development
Boards, Evaluation Kits, and
Starter Kits
The PICkit™ 2 Development Programmer/Debugger is
a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash
families of microcontrollers. The full featured
Windows® programming interface supports baseline
(PIC10F,
PIC12F5xx,
PIC16F5xx),
midrange
(PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30,
dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit
microcontrollers, and many Microchip Serial EEPROM
products. With Microchip’s powerful MPLAB Integrated
Development Environment (IDE) the PICkit™ 2
enables in-circuit debugging on most PIC® microcontrollers. In-Circuit-Debugging runs, halts and single
steps the program while the PIC microcontroller is
embedded in the application. When halted at a breakpoint, the file registers can be examined and modified.
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for
adding custom circuitry and provide application firmware
and source code for examination and modification.
The PICkit 2 Debug Express include the PICkit 2, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
26.12 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages and a modular, detachable socket assembly to support various
package types. The ICSP™ cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices and incorporates an MMC card for file
storage and data applications.
DS33030A-page 264
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip
has a line of evaluation kits and demonstration software
for analog filter design, KEELOQ® security ICs, CAN,
IrDA®, PowerSmart battery management, SEEVAL®
evaluation system, Sigma-Delta ADC, flow rate
sensing, plus many more.
Also available are starter kits that contain everything
needed to experience the specified device. This usually
includes a single application and debug capability, all
on one board.
Check the Microchip web page (www.microchip.com)
for the complete list of demonstration, development
and evaluation kits.
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
27.0
ELECTRICAL CHARACTERISTICS
This section provides an overview of the PIC24FV16KM204 family electrical characteristics. Additional information will
be provided in future revisions of this document as it becomes available.
Absolute maximum ratings for the PIC24FV16KM204 family are listed below. Exposure to these maximum rating
conditions for extended periods may affect device reliability. Functional operation of the device at these, or any other
conditions above the parameters indicated in the operation listings of this specification, is not implied.
Absolute Maximum Ratings(†)
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS (PIC24FXXKMXXX) ........................................................................ -0.3V to +4.5V
Voltage on VDD with respect to VSS (PIC24FVXXKMXXX) ...................................................................... -0.3V to +6.5V
Voltage on any combined analog and digital pin with respect to VSS ............................................ -0.3V to (VDD + 0.3V)
Voltage on any digital only pin with respect to VSS ....................................................................... -0.3V to (VDD + 0.3V)
Voltage on MCLR/VPP pin with respect to VSS ......................................................................................... -0.3V to +9.0V
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin(1) ...........................................................................................................................250 mA
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports(1) ...............................................................................................................200 mA
Note 1:
†
Maximum allowable current is a function of device maximum power dissipation (see Table 27-1).
Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 265
PIC24FV16KM204 FAMILY
27.1
DC Characteristics
Voltage (VDD)
FIGURE 27-1:
PIC24FV16KM204 VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL)
5.5V
5.5V
3.20V
3.20V
2.00V
8 MHz
32 MHz
Frequency
Note:
For frequencies between 8 MHz and 32 MHz, FMAX = 20 MHz * (VDD – 2.0) + 8 MHz.
Voltage (VDD)
FIGURE 27-2:
PIC24F16KM204 FAMILY VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL)
3.60V
3.60V
3.00V
3.00V
1.80V
8 MHz
32 MHz
Frequency
Note:
For frequencies between 8 MHz and 32 MHz, FMAX = 20 MHz * (VDD – 1.8) + 8 MHz.
DS33030A-page 266
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Voltage (VDD)
FIGURE 27-3:
PIC24FV16KM204 VOLTAGE-FREQUENCY GRAPH (EXTENDED)
5.5V
5.5V
3.20V
3.20V
2.00V
8 MHz
24 MHz
Frequency
Note:
Voltage (VDD)
FIGURE 27-4:
For frequencies between 8 MHz and 24 MHz, FMAX = 13.33 MHz * (VDD – 2.0) + 8 MHz.
PIC24F16KM204 FAMILY VOLTAGE-FREQUENCY GRAPH (EXTENDED)
3.60V
3.60V
3.00V
3.00V
1.80V
8 MHz
24 MHz
Frequency
Note:
For frequencies between 8 MHz and 24 MHz, FMAX = 13.33 MHz * (VDD – 1.8) + 8 MHz.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 267
PIC24FV16KM204 FAMILY
TABLE 27-1:
THERMAL OPERATING CONDITIONS
Rating
Symbol
Min
Typ
Max
Unit
Operating Junction Temperature Range
TJ
-40
—
+140
°C
Operating Ambient Temperature Range
TA
-40
—
+125
°C
Power Dissipation:
Internal Chip Power Dissipation:
PINT = VDD x (IDD –  IOH)
PD
PINT + PI/O
W
PDMAX
(TJ – TA)/JA
W
I/O Pin Power Dissipation:
PI/O =  ({VDD – VOH} x IOH) +  (VOL x IOL)
Maximum Allowed Power Dissipation
TABLE 27-2:
THERMAL PACKAGING CHARACTERISTICS
Characteristic
Symbol
Typ
Max
Unit
Notes
Package Thermal Resistance, 20-Pin SPDIP
JA
62.4
—
°C/W
1
Package Thermal Resistance, 28-Pin SPDIP
JA
60
—
°C/W
1
Package Thermal Resistance, 20-Pin SSOP
JA
108
—
°C/W
1
Package Thermal Resistance, 28-Pin SSOP
JA
71
—
°C/W
1
Package Thermal Resistance, 20-Pin SOIC
JA
75
—
°C/W
1
Package Thermal Resistance, 28-Pin SOIC
JA
80.2
—
°C/W
1
Package Thermal Resistance, 28-Pin QFN
JA
32
—
°C/W
1
Package Thermal Resistance, 44-Pin QFN
JA
29
—
°C/W
1
Package Thermal Resistance, 48-Pin UQFN
JA
41
—
°C/W
1
Note 1:
Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations.
TABLE 27-3:
DC CHARACTERISTICS: TEMPERATURE AND VOLTAGE SPECIFICATIONS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KMXXX)
2.0V to 5.5V (PIC24FV16KMXXX)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
No.
Symbol
DC10
VDD
DC12
VDR
Min
Typ(1)
1.8
—
3.6
V
For PIC24F devices
2.0
—
5.5
V
For PIC24FV devices
RAM Data Retention
Voltage(2)
1.6
—
—
V
For PIC24F devices
1.8
—
—
V
For PIC24FV devices
V
Characteristic
Supply Voltage
Max Units
DC16
VPOR
VDD Start Voltage
to Ensure Internal
Power-on Reset Signal
VSS
—
0.7
DC17
SVDD
VDD Rise Rate
to Ensure Internal
Power-on Reset Signal
0.05
—
—
Note 1:
2:
Conditions
V/ms 0-3.3V in 0.1s
0-2.5V in 60 ms
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
This is the limit to which VDD can be lowered without losing RAM data.
DS33030A-page 268
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-4:
HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
Symbol
No.
DC18
VHLVD
Characteristic
HLVD Voltage on
VDD Transition
HLVDL<3:0> = 0000(2)
Typ
Max
Units
—
—
1.90
V
HLVDL<3:0> = 0001
1.88
—
2.13
V
HLVDL<3:0> = 0010
2.09
—
2.35
V
HLVDL<3:0> = 0011
2.25
—
2.53
V
HLVDL<3:0> = 0100
2.35
—
2.62
V
HLVDL<3:0> = 0101
2.55
—
2.84
V
HLVDL<3:0> = 0110
2.80
—
3.10
V
HLVDL<3:0> = 0111
2.95
—
3.25
V
HLVDL<3:0> = 1000
3.09
—
3.41
V
HLVDL<3:0> = 1001
3.27
—
3.59
V
HLVDL<3:0> = 1010(1)
3.46
—
3.79
V
1011(1)
3.62
—
4.01
V
HLVDL<3:0> = 1100(1)
3.91
—
4.26
V
HLVDL<3:0> = 1101(1)
4.18
—
4.55
V
1110(1)
4.49
—
4.87
V
HLVDL<3:0> =
HLVDL<3:0> =
Note 1:
2:
Min
Conditions
These trip points should not be used on PIC24FXXKMXXX devices.
This trip point should not be used on PIC24FVXXKMXXX devices.
TABLE 27-5:
BOR TRIP POINTS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
Sym
No.
Characteristic
DC15
BOR Hysteresis
DC19
BOR Voltage on VDD
Transition
Note 1:
2:
3:
Min
Typ
—
5
BORV<1:0> = 00
—
BORV<1:0> = 01
2.90
Max Units
—
mV
—
—
—
3
3.38
V
Conditions
Valid for LPBOR (Note 1)
BORV<1:0> = 10
2.53
2.7
3.07
V
BORV<1:0> = 11
1.75
1.85 2.05
V
(Note 2)
BORV<1:0> = 11
1.95
2.05 2.16
V
(Note 3)
LPBOR re-arms the POR circuit but does not cause a BOR.
This is valid for PIC24F (3.3V) devices.
This is valid for PIC24FV (5V) devices.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 269
PIC24FV16KM204 FAMILY
TABLE 27-6:
DC CHARACTERISTICS: OPERATING CURRENT (IDD)
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Parameter No.
Device
Typical
Max
Units
Conditions
PIC24FV16KMXXX
269
450
µA
465
830
µA
5.0V
PIC24F16KMXXX
200
330
µA
1.8V
410
750
µA
3.3V
490
—
µA
2.0V
880
—
µA
5.0V
PIC24F16KMXXX
407
—
µA
1.8V
800
—
µA
3.3V
PIC24FV16KMXXX
13.0
15.0
mA
5.0V
PIC24F32KMXXX
12.0
13.0
mA
3.3V
PIC24FV16KMXXX
2.0
—
mA
2.0V
3.5
—
mA
5.0V
1.80
—
mA
1.8V
3.40
—
mA
3.3V
48.0
250
µA
2.0V
75.0
275
µA
5.0V
8.1
28.0
µA
1.8V
13.50
55.00
µA
3.3V
IDD Current
D20
DC22
DC24
DC26
PIC24FV16KMXXX
PIC24F16KMXXX
DC30
PIC24FV16KMXXX
PIC24F16KMXXX
Legend:
Note 1:
2.0V
0.5 MIPS,
FOSC = 1 MHz(1)
1 MIPS,
FOSC = 2 MHz(1)
16 MIPS,
FOSC = 32 MHz(1)
FRC (4 MIPS),
FOSC = 8 MHz
LPRC (15.5 KIPS),
FOSC = 31 kHz
Unshaded rows represent PIC24F16KMXXX devices and shaded rows represent PIC24FV16KMXXX devices.
Oscillator is in External Clock mode (FOSCSEL<2:0> = 010, FOSC<1:0> = 00).
DS33030A-page 270
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-7:
DC CHARACTERISTICS: IDLE CURRENT (IIDLE)
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Parameter No.
Device
Typical
Max
Units
120
200
µA
Conditions
Idle Current (IIDLE)
DC40
PIC24FV16KMXXX
PIC24F16KMXXX
DC42
PIC24FV16KMXXX
PIC24F16KMXXX
DC44
DC46
Legend:
Note 1:
160
430
µA
5.0V
50
100
µA
1.8V
90
370
µA
3.3V
165
—
µA
2.0V
260
—
µA
5.0V
95
—
µA
1.8V
180
—
µA
3.3V
PIC24FV16KMXXX
3.1
6.5
mA
5.0V
PIC24F16KMXXX
2.9
6.0
mA
3.3V
PIC24FV16KMXXX
0.65
—
mA
2.0V
1.0
—
mA
5.0V
0.55
—
mA
1.8V
PIC24F16KMXXX
DC50
2.0V
1.0
—
mA
3.3V
PIC24FV16KMXXX
42
200
µA
2.0V
65
225
µA
5.0V
PIC24F16KMXXX
2.2
18
µA
1.8V
4.0
40
µA
3.3V
0.5 MIPS,
FOSC = 1 MHz(1)
1 MIPS,
FOSC = 2 MHz(1)
16 MIPS,
FOSC = 32 MHz(1)
FRC (4 MIPS),
FOSC = 8 MHz
LPRC (15.5 KIPS),
FOSC = 31 kHz
Unshaded rows represent PIC24F16KMXXX devices and shaded rows represent PIC24FV16KMXXX devices.
Oscillator is in External Clock mode (FOSCSEL<2:0> = 010, FOSC<1:0> = 00).
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 271
PIC24FV16KM204 FAMILY
TABLE 27-8:
DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
DC CHARACTERISTICS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Parameter
No.
Typical(1)
Device
Max
Units
Conditions
Power-Down Current (IPD)
DC60
PIC24FV16KMXXX
—
-40°C
8.0
6.0
6.0
PIC24F16KMXXX
8.5
+25°C
µA
+85°C
15.0
+125°C
—
-40°C
8.0
+25°C
9.0
µA
0.040
DC61
PIC24FV16KMXXX
0.25
0.35
+60°C
10.0
+85°C
15.0
+125°C
—
-40°C
0.80
0.025
+60°C
9.0
1.5
+60°C
+85°C
7.5
+125°C
—
-40°C
1.0
+25°C
µA
+60°C
3.0
+85°C
7.5
+125°C
—
7.5
3.0
7.5
5.0V
Sleep Mode(2)
+25°C
µA
2.0
2.0
2.0V
µA
µA
+85°C
+125°C
+85°C
+125°C
1.8V
3.3V
2.0V
5.0V
Low-Voltage
Sleep Mode(2)
Legend: Unshaded rows represent PIC24F16KMXXX devices and shaded rows represent PIC24FV16KMXXX
devices.
Note 1: Data in the Typical column is at 3.3V, +25°C (PIC24F16KMXXX) or 5.0V, +25°C (PIC24FV16KMXXX)
unless otherwise stated. Parameters are for design guidance only and are not tested.
2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set
low. PMSLP is set to ‘0’ and WDT, etc., are all switched off.
3: The  current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
DS33030A-page 272
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-8:
DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED)
DC CHARACTERISTICS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Parameter
No.
Typical(1)
Max
Units
0.50
—
µA
2.0V
0.70
1.5
µA
5.0V
PIC24F16KMXXX
0.50
—
µA
1.8V
0.70
1.5
µA
3.3V
PIC24FV16KMXXX
0.80
—
µA
2.0V
1.50
2.0
µA
5.0V
PIC24F16KMXXX
0.70
—
µA
1.8V
1.0
1.5
µA
3.3V
PIC24FV16KMXXX
5.4
—
µA
2.0V
8.1
14.0
µA
5.0V
PIC24F16KMXXX
4.9
—
µA
1.8V
7.5
14.0
µA
3.3V
PIC24FV16KMXXX
5.6
—
µA
2.0V
6.5
11.2
µA
5.0V
PIC24F16KMXXX
5.6
—
µA
1.8V
6.0
11.2
µA
3.3V
PIC24FV16KMXXX
0.03
—
µA
2.0V
0.05
0.3
µA
5.0V
0.03
—
µA
1.8V
0.05
0.3
µA
3.3V
Device
Conditions
Module Differential Current (IPD)(3)
DC71
DC72
DC75
DC76
DC78
PIC24FV16KMXXX
PIC24F16KMXXX
Watchdog Timer
Current:
WDT
32 kHz Crystal with RTCC,
DSWDT or Timer1:
SOSC
(SOSCSEL = 0)
HLVD
BOR
Low-Power BOR:
LPBOR
Legend: Unshaded rows represent PIC24F16KMXXX devices and shaded rows represent PIC24FV16KMXXX
devices.
Note 1: Data in the Typical column is at 3.3V, +25°C (PIC24F16KMXXX) or 5.0V, +25°C (PIC24FV16KMXXX)
unless otherwise stated. Parameters are for design guidance only and are not tested.
2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set
low. PMSLP is set to ‘0’ and WDT, etc., are all switched off.
3: The  current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 273
PIC24FV16KM204 FAMILY
TABLE 27-9:
DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
No.
Sym
VIL
Characteristic
Input Low Voltage(4)
Min
Typ(1)
Max
Units
—
—
—
—
Conditions
DI10
I/O Pins
VSS
—
0.2 VDD
V
DI15
MCLR
VSS
—
0.2 VDD
V
DI16
OSCI (XT mode)
VSS
—
0.2 VDD
V
DI17
OSCI (HS mode)
VSS
—
0.2 VDD
V
DI18
I/O Pins with
I2
VSS
—
0.3 VDD
V
SMBus disabled
DI19
I/O Pins with SMBus Buffer
VSS
—
0.8
V
SMBus enabled
Input High Voltage(4,5)
—
—
—
—
I/O Pins:
with Analog Functions
Digital Only
0.8 VDD
0.8 VDD
—
—
VDD
VDD
V
V
DI25
MCLR
0.8 VDD
—
VDD
V
DI26
OSCI (XT mode)
0.7 VDD
—
VDD
V
DI27
OSCI (HS mode)
0.7 VDD
—
VDD
V
DI28
I/O Pins with I2C Buffer:
with Analog Functions
Digital Only
0.7 VDD
0.7 VDD
—
—
VDD
VDD
V
V
2.1
—
VDD
V
2.5V  VPIN  VDD
VIH
DI20
DI29
C™ Buffer
I/O Pins with SMBus
DI30
ICNPU CNx Pull-up Current
50
250
500
A
VDD = 3.3V, VPIN = VSS
DI31
IPU
—
—
30
A
VDD = 2.0V
—
—
1000
A
VDD = 3.3V
IIL
Maximum Load Current for
Digital High Detection
w/Internal Pull-up
Input Leakage Current(2,3)
DI50
I/O Ports
—
0.050
±0.100
A
VSS  VPIN  VDD,
Pin at high-impedance
DI51
Pins with OAxOUT Functions
(RB15 and RB3)
—
0.100
±0.200
A
VSS  VPIN  VDD,
Pin at high-impedance
Note 1:
2:
3:
4:
5:
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
Refer to Table 1-4 and Table 1-5 for I/O pin buffer types.
VIH requirements are met when the internal pull-ups are enabled.
DS33030A-page 274
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
DC CHARACTERISTICS
Param
No.
Sym
VOL
DO10
DO16
VOH
Typ(1)
Output Low Voltage
—
—
All I/O Pins
—
—
0.4
V
IOL = 8.0 mA
VDD = 4.5V
—
—
0.4
V
IOL = 4.0 mA
VDD = 3.6V
—
—
0.4
V
IOL = 3.5 mA
VDD = 2.0V
—
—
0.4
V
IOL = 2.0 mA
VDD = 4.5V
—
—
0.4
V
IOL = 1.2 mA
VDD = 3.6V
—
—
0.4
V
IOL = 0.4 mA
VDD = 2.0V
3.8
—
—
V
IOH = -3.5 mA
VDD = 4.5V
3
—
—
V
IOH = -3.0 mA
VDD = 3.6V
1.6
—
—
V
IOH = -1.0 mA
VDD = 2.0V
Max
Units
Conditions
Output High Voltage
All I/O Pins
DO26
Note 1:
Min
Characteristic
OSC2/CLKO
DO20
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
OSC2/CLKO
3.8
—
—
V
IOH = -2.0 mA
VDD = 4.5V
3
—
—
V
IOH = -1.0 mA
VDD = 3.6V
1.6
—
—
V
IOH = -0.5 mA
VDD = 2.0V
Data in “Typ” column is at +25°C unless otherwise stated. Parameters are for design guidance only and
are not tested.
TABLE 27-11: DC CHARACTERISTICS: PROGRAM MEMORY
DC CHARACTERISTICS
Param
No.
Sym
Characteristic
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ(1)
Max
Units
10,000(2)
—
—
E/W
VMIN
—
3.6
V
—
2
—
ms
40
—
—
Year
—
10
—
mA
Conditions
Program Flash Memory
D130
EP
Cell Endurance
D131
VPR
VDD for Read
D133A TIW
Self-Timed Write Cycle
Time
D134
TRETD Characteristic Retention
D135
IDDP
Note 1:
2:
Supply Current During
Programming
VMIN = Minimum operating voltage
Provided no other specifications
are violated
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
Self-write and block erase.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 275
PIC24FV16KM204 FAMILY
TABLE 27-12: DC CHARACTERISTICS: DATA EEPROM MEMORY
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
No.
Sym
Min
Typ(1)
Max
Units
100,000
—
—
E/W
VMIN
—
3.6
V
Characteristic
Conditions
Data EEPROM Memory
D140
EPD
Cell Endurance
D141
VPRD
VDD for Read
D143A
TIWD
Self-Timed Write Cycle
Time
—
4
—
ms
D143B
TREF
Number of Total
Write/Erase Cycles Before
Refresh
—
10M
—
E/W
D144
TRETDD Characteristic Retention
40
—
—
Year
D145
IDDPD
—
7
—
mA
Note 1:
Supply Current During
Programming
VMIN = Minimum operating
voltage
Provided no other specifications
are violated
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
TABLE 27-13: DC SPECIFICATIONS: COMPARATOR
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
D300
VIOFF
Input Offset Voltage
—
20
40
mV
D301
VICM
Input Common-Mode Voltage
0
—
VDD
V
D302
CMRR
Common-Mode Rejection
Ratio
55
—
—
dB
Conditions
TABLE 27-14: DC SPECIFICATIONS: COMPARATOR VOLTAGE REFERENCE
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
—
VDD/32
LSb
VRD310 CVRES
Resolution
—
VRD311 CVRAA
Absolute Accuracy
—
—
1
LSb
VRD312 CVRUR
Unit Resistor Value (R)
—
2k
—

DS33030A-page 276
Advance Information
Conditions
AVDD = 3.3V-5.5V
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-15: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS
Operating Conditions: -40°C < TA < +85°C (unless otherwise stated)
-40°C  TA  +125°C for Extended
Param
Symbol
No.
Characteristics
Min
Typ
Max
Units
VBG
Band Gap Reference Voltage
0.973
1.024
1.075
V
TBG
Band Gap Reference
Start-up Time
—
1
—
ms
VRGOUT
Regulator Output Voltage
3.1
3.3
3.6
V
CEFC
External Filter Capacitor Value
4.7
10
—
F
VLVR
Low-Voltage Regulator Output
Voltage
—
2.6
—
V
Comments
Series resistance < 3 Ohm
recommended;
< 5 Ohm is required.
TABLE 27-16: CTMU CURRENT SOURCE SPECIFICATIONS
DC CHARACTERISTICS
Param
Sym
No.
Note 1:
2:
Characteristic
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ(1) Max
Units
Comments
IOUT1 CTMU Current
Source, Base Range
—
550
—
nA
CTMUCON1L<1:0> = 01
IOUT2 CTMU Current
Source, 10x Range
—
5.5
—
A
CTMUCON1L<1:0> = 10
IOUT3 CTMU Current
Source, 100x Range
—
55
—
A
CTMUCON1L<1:0> = 11
IOUT4 CTMU Current
Source, 1000x Range
—
550
—
A
CTMUCON1L<1:0> = 00
(Note 2)
VF
Temperature Diode
Forward Voltage
—
.76
—
V
V
Voltage Change per
Degree Celsius
—
1.6
—
mV/°C
Conditions
2.5V < VDD < VDDMAX
Nominal value at the center point of the current trim range (CTMUCON1L<7:2> = 000000). On PIC24F16KM
parts, the current output is limited to the typical current value when IOUT4 is chosen.
Do not use this current range with a temperature sensing diode.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 277
PIC24FV16KM204 FAMILY
TABLE 27-17: OPERATIONAL AMPLIFIER SPECIFICATIONS
DC CHARACTERISTICS
Param
No.
Sym
GBWP
SR
Note 1:
Characteristic
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ(1)
Max
Units
Comments
Gain Bandwidth
Product
—
5
—
MHz
SPDSEL = 1
—
0.5
—
MHz
SPDSEL = 0
Slew Rate
—
1.2
—
V/µs
SPDSEL = 1
—
0.3
—
V/µs
SPDSEL = 0
AOL
DC Open-Loop Gain
—
90
—
dB
VIOFF
Input Offset Voltage
—
±2
±10
mV
VIBC
Input Bias Current
VICM
Common-Mode Input
Voltage Range
CMRR
—
—
—
nA
AVSS
—
AVDD
V
Common-Mode
Rejection Ratio
—
60
—
db
PSRR
Power Supply
Rejection Ratio
—
60
—
dB
VOR
Output Voltage
Range
AVSS + 200 AVSS + 5 to AVDD – 200
AVDD – 5
mV
(Note 1)
0.5V input overdrive,
no output loading
The op amps use CMOS input circuitry with negligible input bias current. The maximum “effective bias
current” is the I/O pin leakage specified by electrical Parameter DI50.
DS33030A-page 278
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
27.2
AC Characteristics and Timing Parameters
The information contained in this section defines the PIC24FV16KM204 family AC characteristics and timing
parameters.
TABLE 27-18: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
Standard Operating Conditions: 1.8V to 3.6V
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Operating voltage VDD range as described in Section 27.1 “DC Characteristics”.
AC CHARACTERISTICS
FIGURE 27-5:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1 – for all pins except OSCO
Load Condition 2 – for OSCO
VDD/2
CL
Pin
RL
VSS
CL
Pin
RL = 464
CL = 50 pF for all pins except OSCO
15 pF for OSCO output
VSS
TABLE 27-19: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS
Param
Symbol
No.
Characteristic
Min
Typ(1)
Max
Units
Conditions
15
pF
In XT and HS modes when
external clock is used to drive
OSCI
COSC2
OSCO/CLKO Pin
—
—
DO56
CIO
All I/O Pins and OSCO
—
—
50
pF
EC mode
DO58
CB
SCLx, SDAx
—
—
400
pF
In I2C™ mode
DO50
Note 1:
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 279
PIC24FV16KM204 FAMILY
FIGURE 27-6:
EXTERNAL CLOCK TIMING
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
OS30
OS30
Q1
Q2
Q3
OSCI
OS20
OS31
OS31
OS25
CLKO
OS40
OS41
TABLE 27-20: EXTERNAL CLOCK TIMING REQUIREMENTS
AC CHARACTERISTICS
Param
Sym
No.
OS10
Characteristic
FOSC External CLKI Frequency
(External clocks allowed
only in EC mode)
Oscillator Frequency
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ(1)
Max
Units
DC
4
DC
4
—
—
—
—
32
8
24
6
MHz
MHz
MHz
MHz
EC, -40°C < TA < +85°C
ECPLL, -40°C < TA < +85°C
EC, -40°C < TA < +125°C
ECPLL, -40°C < TA < +125°C
0.2
4
4
4
31
—
—
—
—
—
4
25
8
6
33
MHz
MHz
MHz
MHz
kHz
XT
HS
XTPLL, -40°C < TA < +85°C
XTPLL, -40°C < TA < +125°C
SOSC
—
—
—
—
Conditions
OS20
TOSC TOSC = 1/FOSC
OS25
TCY
62.5
—
DC
ns
OS30
TosL, External Clock in (OSCI)
TosH High or Low Time
0.45 x TOSC
—
—
ns
EC
OS31
TosR, External Clock in (OSCI)
TosF Rise or Fall Time
—
—
20
ns
EC
OS40
TckR
CLKO Rise Time(3)
—
6
10
ns
OS41
TckF
CLKO Fall Time(3)
—
6
10
ns
Note 1:
2:
3:
Instruction Cycle Time(2)
See Parameter OS10 for FOSC
value
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are
based on characterization data for that particular oscillator type, under standard operating conditions, with
the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption. All devices are tested to operate at “Min.” values with an
external clock applied to the OSCI/CLKI pin. When an external clock input is used, the “Max.” cycle time
limit is “DC” (no clock) for all devices.
Measurements are taken in EC mode. The CLKO signal is measured on the OSCO pin. CLKO is low for the
Q1-Q2 period (1/2 TCY) and high for the Q3-Q4 period (1/2 TCY).
DS33030A-page 280
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-21: PLL CLOCK TIMING SPECIFICATIONS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Sym
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
OS50
FPLLI
PLL Input Frequency
Range
4
—
8
MHz
ECPLL, HSPLL modes,
-40°C  TA  +85°C
OS51
FSYS
PLL Output Frequency
Range
16
—
32
MHz
-40°C  TA  +85°C
OS52
TLOCK PLL Start-up Time
(Lock Time)
—
1
2
ms
OS53
DCLK
-2
1
2
%
Note 1:
2:
CLKO Stability (Jitter)
Measured over 100 ms period
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
TABLE 27-22: INTERNAL RC OSCILLATOR ACCURACY
AC CHARACTERISTICS
Param
No.
Characteristic
FRC @ 8 MHz(1)
F20
LPRC @ 31 kHz(2)
F21
Note 1:
2:
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ
Max
Units
Conditions
-2
—
+2
%
-5
—
+5
%
-40°C  TA +125°C 1.8V  VDD  3.6V, F device
2.0V  VDD  5.5V, FV device
-15
—
+15
%
-40°C  TA +125°C 1.8V  VDD  3.6V, F device
2.0V  VDD  5.5V, FV device
3.0V  VDD  3.6V, F device
3.2V  VDD  5.5V, FV device
+25°C
The frequency is calibrated at +25°C and 3.3V. The OSCTUN bits can be used to compensate for
temperature drift.
The change of LPRC frequency as VDD changes.
TABLE 27-23: INTERNAL RC OSCILLATOR SPECIFICATIONS
AC CHARACTERISTICS
Param
No.
Sym
TFRC
Characteristic
FRC Start-up Time
TLPRC LPRC Start-up Time
 2013 Microchip Technology Inc.
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ
Max
Units
—
5
—
s
—
70
—
s
Advance Information
Conditions
DS33030A-page 281
PIC24FV16KM204 FAMILY
FIGURE 27-7:
CLKO AND I/O TIMING CHARACTERISTICS
I/O Pin
(Input)
DI35
DI40
I/O Pin
(Output)
Old Value
New Value
DO31
DO32
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-24: CLKO AND I/O TIMING REQUIREMENTS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
DO31
TIOR
Port Output Rise Time
—
10
25
ns
DO32
TIOF
Port Output Fall Time
—
10
25
ns
DI35
TINP
INTx Pin High or Low Time
(output)
20
—
—
ns
DI40
TRBP
CNx High or Low Time (input)
2
—
—
TCY
Note 1:
Conditions
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
DS33030A-page 282
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 27-8:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING CHARACTERISTICS
VDD
MCLR
SY12
SY10
Internal
POR
PWRT
SY11
SYSRST
System
Clock
Watchdog
Timer Reset
SY20
SY13
SY13
I/O Pins
SY35
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 283
PIC24FV16KM204 FAMILY
FIGURE 27-9:
BROWN-OUT RESET CHARACTERISTICS
VDDCORE
(Device not in Brown-out Reset)
DC15
DC19
(Device in Brown-out Reset)
SY25
Reset (Due to BOR)
TVREG + TRST
TABLE 27-25: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET TIMING REQUIREMENTS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min.
Typ(1)
Max.
Units
SY10
TmcL
MCLR Pulse Width (low)
2
—
—
s
SY11
TPWRT
Power-up Timer Period
50
64
90
ms
Conditions
SY12
TPOR
Power-on Reset Delay
1
5
10
s
SY13
TIOZ
I/O High-Impedance from
MCLR Low or Watchdog
Timer Reset
—
—
100
ns
SY20
TWDT
Watchdog Timer Time-out
Period
0.85
1.0
1.15
ms
1.32 prescaler
3.4
4.0
4.6
ms
1:128 prescaler
SY25
TBOR
Brown-out Reset Pulse
Width
1
—
—
s
SY35
TFSCM
Fail-Safe Clock Monitor
Delay
—
2.0
2.3
s
SY45
TRST
Internal State Reset Time
—
5
—
s
SY50
TVREG
On-Chip Voltage Regulator
Output Delay
—
10
—
s
SY55
TLOCK
PLL Start-up Time
—
100
—
s
SY65
TOST
Oscillator Start-up Time
—
1024
—
TOSC
SY71
TPM
Program Memory Wake-up
Time
—
1
—
s
SY72
TLVR
Low-Voltage Regulator
Wake-up Time
—
250
—
s
Note 1:
2:
(Note 2)
Sleep wake-up with
PMSLP = 0
Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
This applies to PIC24FV16KMXXX devices only.
DS33030A-page 284
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-26: COMPARATOR TIMING REQUIREMENTS
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
300
TRESP
Response Time*(1)
—
150
400
ns
301
TMC2OV
Comparator Mode Change to
Output Valid*
—
—
10
s
*
Note 1:
Comments
Parameters are characterized but not tested.
Response time is measured with one comparator input at (VDD – 1.5)/2, while the other input transitions
from VSS to VDD.
TABLE 27-27: COMPARATOR VOLTAGE REFERENCE SETTLING TIME SPECIFICATIONS
Param
No.
VR310
Note 1:
Symbol
TSET
Characteristic
Min
Typ
Max
Units
—
—
10
s
Settling Time(1)
Comments
Settling time is measured while CVRSS = 1 and the CVR<3:0> bits transition from ‘0000’ to ‘1111’.
FIGURE 27-10:
CAPTURE/COMPARE/PWM TIMINGS (MCCPx, SCCPx MODULES)
CCPx Time Base
Clock Source
50
51
52
CCPx Capture Input (ICx)
and Gating Inputs
53
54
55
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-28: CAPTURE/COMPARE/PWM REQUIREMENTS (MCCPx, SCCPx MODULES)
Param
Symbol
No.
50
51
52
TCLKL
TCLKH
TCLK
Characteristic
CCPx Time Base Clock Source Low Time
CCPx Time Base Clock Source High Time
CCPx Time Base Clock Source Period
Min
Max
Units
TCY/2
—
ns
TSYNC = 1
31.25
—
ns
TSYNC = 0
TCY/2
—
ns
TSYNC = 1
31.25
—
ns
TSYNC = 0
TCY
—
ns
TSYNC = 1
62.5
—
ns
TSYNC = 0
53
TCCL
CCPx Capture or Gating Input Low Time
TCLK
—
ns
54
TCCH
CCPx Capture or Gating Input High Time
TCLK
—
ns
55
TCCP
CCPx Capture or Gating Input Period
2 * TCLK/N
—
ns
 2013 Microchip Technology Inc.
Conditions
Advance Information
N = prescale
value (1, 4 or 16)
DS33030A-page 285
PIC24FV16KM204 FAMILY
FIGURE 27-11:
EXAMPLE SPI MASTER MODE TIMING (CKE = 0)
SCKx
(CKP = 0)
78
79
79
78
SCKx
(CKP = 1)
bit 6 - - - - - - 1
MSb
SDOx
LSb
75, 76
SDIx
bit 6 - - - - 1
MSb In
LSb In
74
73
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-29: EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 0)
Param
No.
Symbol
Characteristic
Min
Max
Units
73
TDIV2SCH,
TDIV2SCL
Setup Time of SDIx Data Input to SCKx Edge
20
—
ns
74
TSCH2DIL,
TSCL2DIL
Hold Time of SDIx Data Input to SCKx Edge
40
—
ns
75
TDOR
SDOx Data Output Rise Time
—
25
ns
76
TDOF
SDOx Data Output Fall Time
—
25
ns
78
TSCR
SCKx Output Rise Time (Master mode)
—
25
ns
79
TSCF
SCKx Output Fall Time (Master mode)
—
25
ns
FSCK
SCKx Frequency
—
10
MHz
DS33030A-page 286
Advance Information
Conditions
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 27-12:
EXAMPLE SPI MASTER MODE TIMING (CKE = 1)
81
SCKx
(CKP = 0)
79
73
SCKx
(CKP = 1)
78
MSb
SDOx
LSb
bit 6 - - - - - - 1
75, 76
SDIx
bit 6 - - - - 1
MSb In
LSb In
74
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-30: EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 1)
Param.
No.
Symbol
Characteristic
Min
Max
Units
73
TDIV2SCH,
TDIV2SCL
Setup Time of SDIx Data Input to SCKx Edge
35
—
ns
74
TSCH2DIL,
TSCL2DIL
Hold Time of SDIx Data Input to SCKx Edge
40
—
ns
75
TDOR
SDOx Data Output Rise Time
—
25
ns
76
TDOF
SDOx Data Output Fall Time
—
25
ns
78
TSCR
SCKx Output Rise Time (Master mode)
—
25
ns
79
TSCF
SCKx Output Fall Time (Master mode)
81
TDOV2SCH, SDOx Data Output Setup to SCKx Edge
TDOV2SCL
FSCK
SCKx Frequency
 2013 Microchip Technology Inc.
Advance Information
—
25
ns
TCY
—
ns
—
10
MHz
Conditions
DS33030A-page 287
PIC24FV16KM204 FAMILY
FIGURE 27-13:
EXAMPLE SPI SLAVE MODE TIMING (CKE = 0)
SSx
70
SCKx
(CKP = 0)
83
71
72
SCKx
(CKP = 1)
80
MSb
SDOx
bit 6 - - - - - - 1
LSb
75, 76
MSb In
SDIx
77
bit 6 - - - - 1
LSb In
74
73
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-31: EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING, CKE = 0)
Param
No.
Symbol
Characteristic
70
TSSL2SCH, SSx  to SCKx  or SCKx  Input
TSSL2SCL
70A
TSSL2WB SSx to Write to SSPxBUF
71
TSCH
SCKx Input High Time
(Slave mode)
TSCL
SCKx Input Low Time
(Slave mode)
71A
72
72A
Min
Max Units Conditions
3 TCY
—
ns
3 TCY
—
ns
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
Continuous
1.25 TCY + 30
—
ns
Continuous
Single Byte
40
—
ns
20
—
ns
—
ns
—
ns
—
25
ns
SDOx Data Output Fall Time
—
25
ns
73
TDIV2SCH, Setup Time of SDIx Data Input to SCKx Edge
TDIV2SCL
73A
TB2B
74
TSCH2DIL, Hold Time of SDIx Data Input to SCKx Edge
TSCL2DIL
40
75
TDOR
SDOx Data Output Rise Time
76
TDOF
Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40
77
TSSH2DOZ SSx  to SDOx Output High-Impedance
10
50
ns
80
TSCH2DOV, SDOx Data Output Valid After SCKx Edge
TSCL2DOV
—
50
ns
83
TSCH2SSH, SSx  After SCKx Edge
TSCL2SSH
1.5 TCY + 40
—
ns
—
10
MHz
FSCK
Note 1:
2:
SCKx Frequency
(Note 1)
(Note 1)
(Note 2)
Requires the use of Parameter 73A.
Only if Parameters 71A and 72A are used.
DS33030A-page 288
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 27-14:
EXAMPLE SPI SLAVE MODE TIMING (CKE = 1)
82
SSx
SCKx
(CKP = 0)
70
83
71
72
73
SCKx
(CKP = 1)
80
MSb
SDOx
bit 6 - - - - - - 1
LSb
75, 76
SDIx
77
bit 6 - - - - 1
MSb In
LSb In
74
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-32: EXAMPLE SPI SLAVE MODE REQUIREMENTS (CKE = 1)
Param
No.
Symbol
Characteristic
Min
Max Units Conditions
70
TSSL2SCH, SSx  to SCKx  or SCKx  Input
TSSL2SCL
3 TCY
—
ns
70A
TSSL2WB
SSx to Write to SSPxBUF
3 TCY
—
ns
71
TSCH
SCKx Input High Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
SCKx Input Low Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
(Note 1)
—
ns
(Note 2)
—
ns
71A
72
TSCL
72A
73A
TB2B
74
TSCH2DIL, Hold Time of SDIx Data Input to SCKx Edge
TSCL2DIL
75
TDOR
SDOx Data Output Rise Time
—
25
ns
76
TDOF
SDOx Data Output Fall Time
—
25
ns
77
TSSH2DOZ SSx  to SDOx Output High-Impedance
10
50
ns
80
TSCH2DOV, SDOx Data Output Valid After SCKx Edge
TSCL2DOV
—
50
ns
82
TSSL2DOV SDOx Data Output Valid After SSx  Edge
—
50
ns
83
TSCH2SSH, SSx  After SCKx Edge
TSCL2SSH
1.5 TCY + 40
—
ns
—
10
MHz
FSCK
Note 1:
2:
Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40
SCKx Frequency
40
(Note 1)
Requires the use of Parameter 73A.
Only if Parameters 71A and 72A are used.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 289
PIC24FV16KM204 FAMILY
I2C™ BUS START/STOP BITS TIMING
FIGURE 27-15:
SCLx
91
93
90
92
SDAx
Stop
Condition
Start
Condition
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-33: I2C™ BUS START/STOP BITS REQUIREMENTS (SLAVE MODE)
Param.
Symbol
No.
Characteristic
90
TSU:STA
Start Condition
91
THD:STA
92
TSU:STO
93
THD:STO Stop Condition
Max
Units
Conditions
4700
—
ns
Only relevant for Repeated
Start condition
ns
After this period, the first
clock pulse is generated
Setup Time
400 kHz mode
600
—
Start Condition
100 kHz mode
4000
—
Hold Time
400 kHz mode
600
—
Stop Condition
100 kHz mode
4700
—
Setup Time
Hold Time
FIGURE 27-16:
100 kHz mode
Min
400 kHz mode
600
—
100 kHz mode
4000
—
400 kHz mode
600
—
ns
ns
I2C™ BUS DATA TIMING
103
102
100
101
SCLx
90
106
107
91
92
SDAx
In
110
109
109
SDAx
Out
Note:
Refer to Figure 27-5 for load conditions.
DS33030A-page 290
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
TABLE 27-34: I2C™ BUS DATA REQUIREMENTS (SLAVE MODE)
Param.
No.
100
Symbol
THIGH
101
TLOW
102
TR
Characteristic
Clock High Time
Clock Low Time
Min
Max
Units
100 kHz mode
4.0
—
s
Must operate at a minium of
1.5 MHz
400 kHz mode
0.6
—
s
Must operate at a minium of
10 MHz
MSSP module
1.5 TCY
—
—
100 kHz mode
4.7
—
s
Must operate at a minium of
1.5 MHz
400 kHz mode
1.3
—
s
Must operate at a minium of
10 MHz
MSSP module
1.5 TCY
—
—
—
1000
ns
20 + 0.1 CB
300
ns
SDAx and SCLx Rise Time 100 kHz mode
400 kHz mode
103
TF
SDAx and SCLx Fall Time 100 kHz mode
TSU:STA
THD:STA
91
THD:DAT
106
TSU:DAT
107
TSU:STO
92
109
TAA
110
TBUF
D102
CB
Note 1:
2:
CB is specified to be from
10 to 400 pF
—
300
ns
20 + 0.1 CB
300
ns
CB is specified to be from
10 to 400 pF
Start Condition Setup Time 100 kHz mode
4.7
—
s
400 kHz mode
0.6
—
s
Only relevant for Repeated
Start condition
400 kHz mode
90
Conditions
Start Condition Hold Time
Data Input Hold Time
Data Input Setup Time
100 kHz mode
4.0
—
s
400 kHz mode
0.6
—
s
100 kHz mode
0
—
ns
400 kHz mode
0
0.9
s
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
Stop Condition Setup Time 100 kHz mode
4.7
—
s
400 kHz mode
0.6
—
s
100 kHz mode
—
3500
ns
400 kHz mode
—
—
ns
Output Valid from Clock
Bus Free Time
Bus Capacitive Loading
100 kHz mode
4.7
—
s
400 kHz mode
1.3
—
s
—
400
pF
After this period, the first clock
pulse is generated
(Note 2)
(Note 1)
Time the bus must be free before
a new transmission can start
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCLx to avoid unintended generation of Start or Stop conditions.
A Fast mode I2C™ bus device can be used in a Standard mode I2C bus system, but the requirement, TSU:DAT  250 ns,
must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCLx signal. If
such a device does stretch the LOW period of the SCLx signal, it must output the next data bit to the SDAx line,
TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification), before the SCLx line
is released.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 291
PIC24FV16KM204 FAMILY
MSSPx I2C™ BUS START/STOP BITS TIMING WAVEFORMS
FIGURE 27-17:
SCLx
93
91
90
92
SDAx
Stop
Condition
Start
Condition
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-35: I2C™ BUS START/STOP BITS REQUIREMENTS (MASTER MODE)
Param.
Symbol
No.
90
91
TSU:STA
Characteristic
Max
Units
ns
Only relevant for
Repeated Start
condition
ns
After this period, the
first clock pulse is
generated
Start Condition
100 kHz mode
2(TOSC)(BRG + 1)
—
Setup Time
400 kHz mode
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
ns
ns
THD:STA Start Condition
Hold Time
92
TSU:STO Stop Condition
93
THD:STO Stop Condition
Setup Time
Hold Time
DS33030A-page 292
Min
400 kHz mode
2(TOSC)(BRG + 1)
—
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
Advance Information
Conditions
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 27-18:
MSSPx I2C™ BUS DATA TIMING
103
102
100
101
SCLx
90
106
91
SDAx
In
92
107
110
109
109
SDAx
Out
Note:
Refer to Figure 27-5 for load conditions.
TABLE 27-36: I2C™ BUS DATA REQUIREMENTS (MASTER MODE)
Param.
Symbol
No.
100
101
102
103
90
91
106
107
92
109
110
D102
Note 1:
THIGH
TLOW
TR
TF
TSU:STA
Characteristic
Min
Max
Units
Clock High Time 100 kHz mode
2(TOSC)(BRG + 1)
—
—
400 kHz mode
2(TOSC)(BRG + 1)
—
—
Clock Low Time 100 kHz mode
2(TOSC)(BRG + 1)
—
—
400 kHz mode
2(TOSC)(BRG + 1)
—
—
SDAx and SCLx 100 kHz mode
Rise Time
400 kHz mode
—
1000
ns
20 + 0.1 CB
300
ns
SDAx and SCLx 100 kHz mode
Fall Time
400 kHz mode
—
300
ns
20 + 0.1 CB
300
ns
Start Condition
Setup Time
100 kHz mode
2(TOSC)(BRG + 1)
—
—
400 kHz mode
2(TOSC)(BRG + 1)
—
—
THD:STA Start Condition
Hold Time
100 kHz mode
2(TOSC)(BRG + 1)
—
—
400 kHz mode
2(TOSC)(BRG + 1)
—
—
THD:DAT Data Input
Hold Time
100 kHz mode
0
—
ns
400 kHz mode
0
0.9
s
TSU:DAT
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
Data Input
Setup Time
TSU:STO Stop Condition
Setup Time
100 kHz mode
2(TOSC)(BRG + 1)
—
—
400 kHz mode
2(TOSC)(BRG + 1)
—
—
TAA
100 kHz mode
—
3500
ns
400 kHz mode
—
1000
ns
TBUF
CB
Output Valid
from Clock
Bus Free Time
100 kHz mode
4.7
—
s
400 kHz mode
1.3
—
s
—
400
pF
Bus Capacitive Loading
Conditions
CB is specified to be from
10 to 400 pF
CB is specified to be from
10 to 400 pF
Only relevant for Repeated
Start condition
After this period, the first
clock pulse is generated
(Note 1)
Time the bus must be free
before a new transmission
can start
A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but Parameter 107  250 ns
must then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCLx signal. If such a device does stretch the LOW period of the SCLx signal, it must output the next data
bit to the SDAx line, Parameter 102 + Parameter 107 = 1000 + 250 = 1250 ns (for 100 kHz mode), before
the SCLx line is released.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 293
PIC24FV16KM204 FAMILY
TABLE 27-37: A/D MODULE SPECIFICATIONS
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min.
Typ
Max.
Units
Conditions
Device Supply
AD01
AVDD
Module VDD Supply
AD02
AVSS
Module VSS Supply
AD05
VREFH
Reference Voltage High
AD06
VREFL
Reference Voltage Low
AD07
VREF
Absolute Reference
Voltage
AD08
IVREF
AD09
ZVREF
Greater of:
VDD – 0.3 or 1.8
—
Lesser of:
VDD + 0.3 or 3.6
V
PIC24FXXKMXXX devices
Greater of:
VDD – 0.3 or 2.0
—
Lesser of:
VDD + 0.3 or 5.5
V
PIC24FVXXKMXXX
devices
VSS – 0.3
—
VSS + 0.3
V
AVDD
V
Reference Inputs
AVSS + 1.7
—
AVSS
—
AVDD – 1.7
V
AVSS – 0.3
—
AVDD + 0.3
V
Reference Voltage Input
Current
—
1.25
—
mA
Reference Input
Impedance
—
10k
—

Analog Input
AD10
VINH-VINL Full-Scale Input Span
VREFL
—
VREFH
V
AD11
VIN
Absolute Input Voltage
AVSS – 0.3
—
AVDD + 0.3
V
AD12
VINL
Absolute VINL Input
Voltage
AVSS – 0.3
—
AVDD/2
V
AD17
RIN
Recommended
Impedance of Analog
Voltage Source
—
—
1k

AD20b NR
Resolution
—
12
—
bits
AD21b INL
Integral Nonlinearity
—
±1
±9
LSb VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 5V
AD22b DNL
Differential Nonlinearity
—
±1
±5
LSb VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 5V
AD23b GERR
Gain Error
—
±1
±9
LSb VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 5V
AD24b EOFF
Offset Error
—
±1
±5
LSb VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 5V
AD25b
Monotonicity(1)
—
—
—
(Note 2)
12-bit
A/D Accuracy
Note 1:
2:
—
Guaranteed
The A/D conversion result never decreases with an increase in the input voltage.
Measurements are taken with external VREF+ and VREF- used as the A/D voltage reference.
DS33030A-page 294
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
FIGURE 27-19:
A/D CONVERSION TIMING
BSET AD1CON1, SAMP
BCLR AD1CON1, SAMP
(Note 2)
AD55
Q3/Q4
AD58
A/D
AD59
AD50
CLK(1)
A/D DATA
11
10
... ...
9
2
1
0
OLD DATA
ADC1BUFn
NEW DATA
AD1IF
TCY
SAMP
Note 1:
SAMPLING STOPPED
If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the
SLEEP instruction to be executed.
This is a minimal RC delay (typically 100 ns) which also disconnects the holding capacitor from the analog input.
2:
TABLE 27-38: A/D CONVERSION TIMING REQUIREMENTS(1)
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Sym
Characteristic
Min.
Typ
Max.
Units
Conditions
Clock Parameters
AD50
TAD
A/D Clock Period
600
—
—
ns
AD51
TRC
A/D Internal RC Oscillator Period
—
1.67
—
µs
AD55
TCONV Conversion Time
—
—
12
14
—
—
TAD
TAD
AD56
FCNV
—
—
100
ksps
AD57
TSAMP Sample Time
AD58
TACQ
Acquisition Time
AD59
TSWC
AD60
AD61
TCY = 75 ns, AD1CON3 in
default state
Conversion Rate
Throughput Rate
—
1
—
TAD
750
—
—
ns
Switching Time from Convert to
Sample
—
—
(Note 3)
TDIS
Discharge Time
12
—
—
TAD
TPSS
Sample Start Delay from
Setting Sample bit (SAMP)
3
TAD
10-bit results
12-bit results
(Note 2)
Clock Parameters
Note 1:
2:
3:
2
—
Because the sample caps will eventually lose charge, clock rates below 10 kHz can affect linearity
performance, especially at elevated temperatures.
The time for the holding capacitor to acquire the “New” input voltage when the voltage changes full scale
after the conversion (VDD to VSS or VSS to VDD).
On the following cycle of the device clock.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 295
PIC24FV16KM204 FAMILY
TABLE 27-39: 8-BIT DIGITAL-TO-ANALOG CONVERTER SPECIFICATIONS
Standard Operating Conditions: 1.8V to 3.6V (PIC24F16KM204)
2.0V to 5.5V (PIC24FV16KM204)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Sym
Characteristic
Resolution
Typ
8
Max.
Units
—
—
bits
DACREF<1:0> Input Voltage AVSS + 1.8
Range
—
AVDD
V
Differential Linearity Error
(DNL)
—
—
±0.5
LSb
Integral Linearity Error (INL)
—
—
±1.5
LSb
Offset Error
—
—
±0.5
LSb
Gain Error
—
—
±3.0
LSb
—
—
—
Monotonicity
Output Voltage Range
Note 1:
Min.
AVSS + 50 AVSS + 5 to AVDD – 50
AVDD – 5
Comments
—
(Note 1)
mV
0.5V input overdrive,
no output loading
Slew Rate
—
5
—
V/µs
Settling Time
—
10
—
µs
DAC output voltage never decreases with an increase in the data code.
DS33030A-page 296
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
28.0
PACKAGING INFORMATION
28.1
Package Marking Information
20-Lead PDIP (300 mil)
Example
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
YYWWNNN
PIC24F08KM101
-I/P e3
1242M7W
28-Lead SPDIP (.300")
Example
PIC24F16KM202
-I/SP e3
1242M7W
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
YYWWNNN
20-Lead SSOP (5.30 mm)
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
PIC24F08KM101
301-I/SS e3
1242M7W
28-Lead SSOP (5.30 mm)
XXXXXXXXXXXX
XXXXXXXXXXXX
YYWWNNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Example
Example
PIC24F16KM202
302-I/SS e3
1242M7W
Product-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it
will be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 297
PIC24FV16KM204 FAMILY
20-Lead SOIC (7.50 mm)
Example
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
PIC24F08KM101
-I/SO e3
1242M7W
YYWWNNN
28-Lead SOIC (7.50 mm)
Example
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
YYWWNNN
PIC24F16KM202
-I/SO e3
1242M7W
28-Lead QFN (6x6 mm)
PIN 1
Example
PIN 1
XXXXXXXX
XXXXXXXX
YYWWNNN
DS33030A-page 298
24F16KM
202-I/ML e3
1242M7W
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
44-Lead QFN (8x8x0.9 mm)
PIN 1
Example
PIN 1
XXXXXXXXXXX
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
PIC24FV16KM
204-I/ML e3
1242M7W
44-Lead TQFP (10x10x1 mm)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
24FV16KM
204-I/PT e3
1242M7W
48-Lead UQFN (6x6x0.5 mm)
PIN 1
Example
PIN 1
XXXXXXXX
XXXXXXXX
YYWWNNN
 2013 Microchip Technology Inc.
24FV16KM
204-I/MV e3
1242M7W
Advance Information
DS33030A-page 299
PIC24FV16KM204 FAMILY
28.2
Package Details
The following sections give the technical details of the packages.
/HDG3ODVWLF'XDO,Q/LQH 3 ±PLO%RG\>3',3@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
N
E1
NOTE 1
1
2
3
D
E
A2
A
L
c
A1
b1
b
eB
e
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
,1&+(6
0,1
1
120
0$;
3LWFK
H
7RSWR6HDWLQJ3ODQH
$
±
±
0ROGHG3DFNDJH7KLFNQHVV
$
%DVHWR6HDWLQJ3ODQH
$
±
±
6KRXOGHUWR6KRXOGHU:LGWK
(
0ROGHG3DFNDJH:LGWK
(
2YHUDOO/HQJWK
'
7LSWR6HDWLQJ3ODQH
/
/HDG7KLFNQHVV
F
E
E
H%
±
±
8SSHU/HDG:LGWK
/RZHU/HDG:LGWK
2YHUDOO5RZ6SDFLQJ†
%6&
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
†6LJQLILFDQW&KDUDFWHULVWLF
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS33030A-page 300
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
/HDG6NLQQ\3ODVWLF'XDO,Q/LQH 63 ±PLO%RG\>63',3@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
N
NOTE 1
E1
1
2 3
D
E
A2
A
L
c
b1
A1
b
e
eB
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
,1&+(6
0,1
1
120
0$;
3LWFK
H
7RSWR6HDWLQJ3ODQH
$
±
±
0ROGHG3DFNDJH7KLFNQHVV
$
%DVHWR6HDWLQJ3ODQH
$
±
±
6KRXOGHUWR6KRXOGHU:LGWK
(
0ROGHG3DFNDJH:LGWK
(
2YHUDOO/HQJWK
'
7LSWR6HDWLQJ3ODQH
/
/HDG7KLFNQHVV
F
E
E
H%
±
±
8SSHU/HDG:LGWK
/RZHU/HDG:LGWK
2YHUDOO5RZ6SDFLQJ†
%6&
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
†6LJQLILFDQW&KDUDFWHULVWLF
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 301
PIC24FV16KM204 FAMILY
/HDG3ODVWLF6KULQN6PDOO2XWOLQH 66 ±PP%RG\>6623@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
N
E
E1
NOTE 1
1 2
e
b
c
A2
A
φ
A1
L1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
L
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
±
%6&
±
0ROGHG3DFNDJH7KLFNQHVV
$
6WDQGRII
$
±
±
2YHUDOO:LGWK
(
0ROGHG3DFNDJH:LGWK
(
2YHUDOO/HQJWK
'
)RRW/HQJWK
/
)RRWSULQW
/
5()
/HDG7KLFNQHVV
F
±
)RRW$QJOH
ƒ
ƒ
ƒ
/HDG:LGWK
E
±
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS33030A-page 302
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 303
PIC24FV16KM204 FAMILY
/HDG3ODVWLF6KULQN6PDOO2XWOLQH 66 ±PP%RG\>6623@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
N
E
E1
1 2
NOTE 1
b
e
c
A2
A
φ
A1
L
L1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
±
%6&
±
0ROGHG3DFNDJH7KLFNQHVV
$
6WDQGRII
$
±
±
2YHUDOO:LGWK
(
0ROGHG3DFNDJH:LGWK
(
2YHUDOO/HQJWK
'
)RRW/HQJWK
/
)RRWSULQW
/
5()
/HDG7KLFNQHVV
F
±
)RRW$QJOH
ƒ
ƒ
ƒ
/HDG:LGWK
E
±
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS33030A-page 304
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 305
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS33030A-page 306
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 307
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS33030A-page 308
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 309
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS33030A-page 310
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 311
PIC24FV16KM204 FAMILY
DS33030A-page 312
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 313
PIC24FV16KM204 FAMILY
/HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 0/ ±[PP%RG\>4)1@
ZLWKPP&RQWDFW/HQJWK
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
DS33030A-page 314
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 315
PIC24FV16KM204 FAMILY
DS33030A-page 316
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 317
PIC24FV16KM204 FAMILY
/HDG3ODVWLF7KLQ4XDG)ODWSDFN 37 ±[[PP%RG\PP>74)3@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
D1
E
e
E1
N
b
NOTE 1
1 2 3
NOTE 2
α
A
φ
c
β
A2
A1
L
L1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI/HDGV
0,//,0(7(56
0,1
120
1
0$;
/HDG3LWFK
H
2YHUDOO+HLJKW
$
±
%6&
±
0ROGHG3DFNDJH7KLFNQHVV
$
6WDQGRII
$
±
)RRW/HQJWK
/
)RRWSULQW
/
5()
)RRW$QJOH
2YHUDOO:LGWK
(
ƒ
%6&
ƒ
2YHUDOO/HQJWK
'
%6&
0ROGHG3DFNDJH:LGWK
(
%6&
0ROGHG3DFNDJH/HQJWK
'
%6&
ƒ
/HDG7KLFNQHVV
F
±
/HDG:LGWK
E
0ROG'UDIW$QJOH7RS
ƒ
ƒ
ƒ
0ROG'UDIW$QJOH%RWWRP
ƒ
ƒ
ƒ
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
&KDPIHUVDWFRUQHUVDUHRSWLRQDOVL]HPD\YDU\
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS33030A-page 318
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 319
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS33030A-page 320
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 321
PIC24FV16KM204 FAMILY
DS33030A-page 322
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
APPENDIX A:
REVISION HISTORY
Revision A (February 2013)
Original data sheet for the PIC24FV16KM204 family of
devices.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 323
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 324
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
INDEX
A
A/D
Buffer Data Formats ................................................. 225
Control Registers ..................................................... 212
AD1CHITH/L .................................................... 212
AD1CHS .......................................................... 212
AD1CON1 ........................................................ 212
AD1CON2 ........................................................ 212
AD1CON3 ........................................................ 212
AD1CON5 ........................................................ 212
AD1CSSH/L ..................................................... 212
AD1CTMENH/L ............................................... 212
Module Specifications .............................................. 294
Sampling Requirements ........................................... 223
Transfer Function ..................................................... 224
AC Characteristics
8-Bit DAC ................................................................. 296
Capacitive Loading Requirements on
Output Pins ...................................................... 279
Internal RC Accuracy ............................................... 281
Internal RC Oscillator Specifications ........................ 281
Load Conditions and Requirements ......................... 279
Reset, Watchdog Timer. Oscillator Start-up
Timer, Power-up Timer, Brown-out
Reset Requirements ........................................ 284
Temperature and Voltage Specifications ................. 279
Assembler
MPASM Assembler .................................................. 262
B
Block Diagrams
12-Bit A/D Converter ................................................ 210
12-Bit A/D Converter Analog Input Model ................ 223
16-Bit Timer1 ........................................................... 141
32-Bit Timer Mode ................................................... 145
Accessing Program Memory with
Table Instructions .............................................. 65
CALL Stack Frame ..................................................... 63
CLC Logic Function Combinatorial Options ............. 196
CLCx Input Source Selection ................................... 197
CLCx Module ........................................................... 195
Comparator Module ................................................. 235
Comparator Voltage Reference ............................... 239
CPU Programmer’s Model ......................................... 37
CTMU Connections and Internal Configuration for
Capacitance Measurement .............................. 242
CTMU Connections and Internal Configuration for
Pulse Delay Generation ................................... 243
CTMU Connections and Internal Configuration for
Time Measurement .......................................... 242
Data Access from Program Space
Address Generation ........................................... 64
Data EEPROM Addressing with TBLPAG and
NVM Registers ................................................... 75
Dual 16-Bit Timer Mode ........................................... 145
High/Low-Voltage Detect (HLVD) ............................ 207
Individual Comparator Configurations ...................... 236
Input Capture x ........................................................ 147
MCCPx/SCCPx Timer Clock Generator .................. 143
MSSPx (I2C Master Mode) ...................................... 161
MSSPx (I2C Mode) .................................................. 161
MSSPx (SPI Mode) .................................................. 160
On-Chip Regulator Connections .............................. 257
 2013 Microchip Technology Inc.
Output Compare x ................................................... 146
PIC24F CPU Core ..................................................... 36
PIC24FV16KM204 Family (General) ......................... 19
PSV Operation ........................................................... 66
Reset System ............................................................ 79
RTCC Module .......................................................... 181
Serial Resistor ......................................................... 132
Shared I/O Port Structure ........................................ 137
Simplified Single DAC ............................................. 229
Simplified UARTx .................................................... 173
Single Operational Amplifier .................................... 233
SPI Master/Slave Connection .................................. 160
System Clock ........................................................... 121
Timer Clock Generator ............................................ 144
Watchdog Timer (WDT) ........................................... 258
Brown-out Reset
Trip Points ............................................................... 269
C
C Compilers
MPLAB C18 ............................................................. 262
Capture/Compare/PWM/Timer
Auxiliary Output ....................................................... 148
General Purpose Timer ........................................... 144
Input Capture Mode ................................................. 147
Output Compare Mode ............................................ 146
Synchronization Sources ......................................... 152
Time Base Generator .............................................. 144
Capture/Compare/PWM/Timer (MCCP, SCCP) .............. 143
Charge Time Measurement Unit. See CTMU.
CLC
Control Registers ..................................................... 198
Code Examples
’C’ Code Sequence for Clock Switching .................. 128
’C’ Power-Saving Entry ............................................ 131
Assembly Code Sequence for Clock Switching ....... 128
Data EEPROM Bulk Erase ........................................ 77
Data EEPROM Unlock Sequence ............................. 73
Erasing a Program Memory Row, ‘C’ Language ....... 70
Erasing a Program Memory Row,
Assembly Language .......................................... 70
I/O Port Write/Read ................................................. 140
Initiating a Programming Sequence,
‘C’ Language ..................................................... 72
Initiating a Programming Sequence,
Assembly Language .......................................... 72
Loading the Write Buffers, ‘C’ Language ................... 71
Loading the Write Buffers, Assembly Language ....... 71
Reading Data EEPROM Using
TBLRD Command ............................................. 78
Setting the RTCWREN Bit in ‘C’ .............................. 182
Setting the RTCWREN Bit in Assembly .................. 182
Single-Word Erase .................................................... 76
Single-Word Write to Data EEPROM ........................ 77
Ultra Low-Power Wake-up Initialization ................... 132
Code Protection ............................................................... 259
Comparator ...................................................................... 235
Comparator Voltage Reference ....................................... 239
Configuring .............................................................. 239
Configurable Logic Cell (CLC) ......................................... 195
Configuration Bits ............................................................ 249
Advance Information
DS33030A-page 325
PIC24FV16KM204 FAMILY
CPU
ALU ............................................................................ 39
Control Registers ....................................................... 38
Core Registers ........................................................... 36
Programmer’s Model .................................................. 35
CTMU
Measuring Capacitance ........................................... 241
Measuring Time ....................................................... 242
Pulse Generation and Delay .................................... 243
Customer Change Notification Service ............................ 330
Customer Notification Service .......................................... 330
Customer Support ............................................................ 330
D
Data EEPROM Memory ..................................................... 73
Erasing ....................................................................... 76
Operations ................................................................. 75
Programming
Bulk Erase .......................................................... 77
Reading Data EEPROM .................................... 78
Single-Word Write .............................................. 77
Programming Control Registers
NVMADR(U) ...................................................... 75
NVMCON ........................................................... 73
NVMKEY ............................................................ 73
Data Memory
Address Space ........................................................... 43
Width .................................................................. 43
Near Data Space ....................................................... 44
Organization, Alignment ............................................. 44
SFR Space ................................................................. 44
Software Stack ........................................................... 63
Data Space
Memory Map .............................................................. 43
DC Characteristics
BOR Trip Points ....................................................... 269
Comparator .............................................................. 276
Comparator Voltage Reference ............................... 276
CTMU Current Source ............................................. 277
Data EEPROM Memory ........................................... 276
High/Low-Voltage Detect ......................................... 269
I/O Pin Input Specifications ...................................... 274
I/O Pin Output Specifications ................................... 275
Idle Current (IIDLE) ................................................... 271
Internal Voltage Regulator ....................................... 277
Operating Current (IDD) ............................................ 270
Operational Amplifier ............................................... 278
Power-Down Current (IPD) ....................................... 272
Program Memory ..................................................... 275
Temperature and Voltage Specifications ................. 268
Development Support ...................................................... 261
Device Features
PIC24F16KM104 Family ............................................ 16
PIC24F16KM204 Family ............................................ 15
PIC24FV16KM104 Family ......................................... 18
PIC24FV16KM204 Family ......................................... 17
Device Overview ................................................................ 13
Core Features ............................................................ 13
Other Special Features .............................................. 14
Pinout Description ...................................................... 20
Dual Operational Amplifier ............................................... 233
DS33030A-page 326
E
Electrical Characteristics
Absolute Maximum Ratings ..................................... 265
Thermal Operating Conditions ................................. 268
Thermal Packaging .................................................. 268
V/F Graphs (PIC24F16KM204) ............................... 266
V/F Graphs (PIC24FV16KM204) ............................. 266
Equations
A/D Conversion Clock Period .................................. 223
UARTx Baud Rate with BRGH = 0 .......................... 174
UARTx Baud Rate with BRGH = 1 .......................... 174
Errata ................................................................................. 11
Examples
Baud Rate Error Calculation (BRGH = 0) ................ 174
F
Flash Program Memory
Control Registers ....................................................... 68
Enhanced ICSP Operation ........................................ 68
Programming Algorithm ............................................. 70
Programming Operations ........................................... 68
RTSP Operation ........................................................ 68
Table Instructions ...................................................... 67
H
High/Low-Voltage Detect (HLVD) .................................... 207
I
I/O Ports
Analog Port Pins Configuration ................................ 138
Analog Selection Registers ...................................... 138
Input Change Notification ........................................ 140
Open-Drain Configuration ........................................ 138
Parallel (PIO) ........................................................... 137
In-Circuit Debugger .......................................................... 259
In-Circuit Serial Programming (ICSP) .............................. 259
Inter-Integrated Circuit. See I2C.
Internet Address .............................................................. 330
Interrupts
Alternate Interrupt Vector Table (AIVT) ..................... 85
Control and Status Registers ..................................... 88
Implemented Vectors ................................................. 87
Interrupt Vector Table (IVT) ....................................... 85
Reset Sequence ........................................................ 85
Setup Procedures .................................................... 119
Trap Vectors .............................................................. 87
Vector Table .............................................................. 86
M
Master Synchronous Serial Port (MSSP) ........................ 159
Microchip Internet Web Site ............................................. 330
MPLAB ASM30 Assembler, Linker, Librarian .................. 262
MPLAB Integrated Development
Environment Software ............................................. 261
MPLAB PM3 Device Programmer ................................... 264
MPLAB REAL ICE In-Circuit Emulator System ............... 263
MPLINK Object Linker/MPLIB Object Librarian ............... 262
N
Near Data Space ............................................................... 44
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
O
On-Chip Voltage Regulator .............................................. 257
Oscillator Configuration
Clock Switching ........................................................ 127
Sequence ......................................................... 127
Configuration Bit Values for Clock Selection ........... 122
Control Registers ..................................................... 123
CPU Clocking Scheme ............................................ 122
Initial Configuration on POR .................................... 122
Reference Clock Output ........................................... 128
P
Packaging
Details ...................................................................... 300
Marking .................................................................... 297
Power-Saving ................................................................... 135
Power-Saving Features ................................................... 131
Clock Frequency, Clock Switching ........................... 131
Coincident Interrupts ................................................ 132
Instruction-Based Modes ......................................... 131
Idle ................................................................... 132
Sleep ................................................................ 131
Retention Regulator (RETREG) ............................... 134
Selective Peripheral Control .................................... 135
Ultra Low-Power Wake-up ....................................... 132
Voltage Regulator-Based ......................................... 134
Retention Sleep Mode ..................................... 134
Run Mode ........................................................ 134
Sleep Mode ...................................................... 134
Product Identification System .......................................... 332
Program and Data Memory
Access Using Table Instructions ................................ 65
Program Space Visibility ............................................ 66
Program and Data Memory Spaces
Interfacing, Addressing .............................................. 63
Program Memory
Address Space ........................................................... 41
Configuration Word Addresses .................................. 42
Program Space
Memory Map .............................................................. 41
Program Verification ........................................................ 259
R
Reader Response ............................................................ 331
Register Maps
ADC ........................................................................... 59
ANSEL ....................................................................... 60
Band Gap Buffer Control ............................................ 61
CLC1-2 ....................................................................... 48
Clock Control ............................................................. 62
Comparator ................................................................ 61
CPU Core ................................................................... 45
CTMU ......................................................................... 60
DAC1 ......................................................................... 56
DAC2 ......................................................................... 56
ICN ............................................................................. 46
Interrupt Controller ..................................................... 47
MCCP1 ...................................................................... 49
MCCP2 ...................................................................... 50
MCCP3 ...................................................................... 51
MSSP1 (I2C/SPI) ....................................................... 54
MSSP2 (I2C/SPI) ....................................................... 54
NVM ........................................................................... 62
Op Amp 1 ................................................................... 56
Op Amp 2 ................................................................... 56
Pad Configuration ...................................................... 58
 2013 Microchip Technology Inc.
PMD ........................................................................... 62
PORTA ...................................................................... 57
PORTB ...................................................................... 57
PORTC ...................................................................... 57
Real-Time Clock and Calendar ................................. 60
SCCP4 ....................................................................... 52
SCCP5 ....................................................................... 53
Timer1 ....................................................................... 48
UART1 ....................................................................... 55
UART2 ....................................................................... 55
Ultra Low-Power Wake-up ......................................... 62
Registers
AD1CHITH (A/D Scan Compare Hit,
High Word) ...................................................... 219
AD1CHITL (A/D Scan Compare Hit, Low Word) ..... 220
AD1CHS (A/D Sample Select) ................................ 218
AD1CON1 (A/D Control 1) ....................................... 213
AD1CON2 (A/D Control 2) ....................................... 215
AD1CON3 (A/D Control 3) ....................................... 216
AD1CON5 (A/D Control 5) ....................................... 217
AD1CSSH (A/D Input Scan Select, High Word) ...... 221
AD1CSSL (A/D Input Scan Select, Low Word) ....... 221
AD1CTMENH (CTMU Enable, High Word) ............. 222
AD1CTMENL (CTMU Enable, Low Word) ............... 222
ALCFGRPT (Alarm Configuration) .......................... 186
ALMINSEC (Alarm Minutes and
Seconds Value) ............................................... 190
ALMTHDY (Alarm Month and Day Value) ............... 189
ALWDHR (Alarm Weekday and Hours Value) ........ 189
AMPxCON (Op Amp x Control) ............................... 234
ANSA (Analog Selection, PORTA) .......................... 138
ANSB (Analog Selection, PORTB) .......................... 139
ANSC (Analog Selection, PORTC) .......................... 139
CCPxCON1H (CCPx Control 1 High) ...................... 151
CCPxCON1L (CCPx Control 1 Low) ....................... 149
CCPxCON2H (CCPx Control 2 High) ...................... 154
CCPxCON2L (CCPx Control 2 Low) ....................... 153
CCPxCON3H (CCPx Control 3 High) ...................... 156
CCPxCON3L (CCPx Control 3 Low) ....................... 155
CCPxSTATL (CCPx Status) .................................... 157
CLCxCONH (CLCx Control High) ............................ 199
CLCxCONL (CLCx Control Low) ............................. 198
CLCxGLSL (CLCx Gate Logic Input Select High) ... 204
CLCxGLSL (CLCx Gate Logic Input Select Low) .... 202
CLCxMUX (CLCx Input MUX Select) ...................... 200
CLKDIV (Clock Divider) ........................................... 125
CMSTAT (Comparator Status) ................................ 238
CMxCON (Comparator x Control) ........................... 237
CORCON (CPU Control) ........................................... 39
CORCON (CPU Core Control) .................................. 90
CTMUCON1H (CTMU Control 1 High) .................... 246
CTMUCON1L (CTMU Control 1 Low) ..................... 244
CTMUCON2L (CTMU Control 2 Low) ..................... 248
CVRCON (Comparator Voltage
Reference Control) .......................................... 240
DACxCON (DACx Control) ...................................... 230
DEVID (Device ID) ................................................... 255
DEVREV (Device Revision) ..................................... 256
FBS (Boot Segment Configuration) ......................... 249
FGS (General Segment Configuration) ................... 250
FICD (In-Circuit Debugger Configuration) ............... 254
FOSC (Oscillator Configuration) .............................. 251
FOSCSEL (Oscillator Selection Configuration) ....... 250
FPOR (Reset Configuration) ................................... 253
FWDT (Watchdog Timer Configuration) .................. 252
HLVDCON (High/Low-Voltage Detect Control) ....... 208
Advance Information
DS33030A-page 327
PIC24FV16KM204 FAMILY
IEC0 (Interrupt Enable Control 0) .............................. 98
IEC1 (Interrupt Enable Control 1) .............................. 99
IEC2 (Interrupt Enable Control 2) ............................ 100
IEC3 (Interrupt Enable Control 3) ............................ 100
IEC4 (Interrupt Enable Control 4) ............................ 101
IEC5 (Interrupt Enable Control 5) ............................ 102
IEC6 (Interrupt Enable Control 6) ............................ 102
IFS0 (Interrupt Flag Status 0) .................................... 93
IFS1 (Interrupt Flag Status 1) .................................... 94
IFS2 (Interrupt Flag Status 2) .................................... 95
IFS3 (Interrupt Flag Status 3) .................................... 95
IFS4 (Interrupt Flag Status 4) .................................... 96
IFS5 (Interrupt Flag Status 5) .................................... 97
IFS6 (Interrupt Flag Status 6) .................................... 97
INTCON1 (Interrupt Control 1) ................................... 91
INTCON2 (Interrupt Control 2) ................................... 92
INTTREG (Interrupt Control and Status) .................. 118
IPC0 (Interrupt Priority Control 0) ............................ 103
IPC1 (Interrupt Priority Control 1) ............................ 104
IPC10 (Interrupt Priority Control 10) ........................ 111
IPC12 (Interrupt Priority Control 12) ........................ 112
IPC15 (Interrupt Priority Control 15) ........................ 113
IPC16 (Interrupt Priority Control 16) ........................ 114
IPC18 (Interrupt Priority Control 18) ........................ 115
IPC19 (Interrupt Priority Control 19) ........................ 116
IPC2 (Interrupt Priority Control 2) ............................ 105
IPC20 (Interrupt Priority Control 20) ........................ 117
IPC24 (Interrupt Priority Control 24) ........................ 117
IPC3 (Interrupt Priority Control 3) ............................ 106
IPC4 (Interrupt Priority Control 4) ............................ 107
IPC5 (Interrupt Priority Control 5) ............................ 108
IPC6 (Interrupt Priority Control 6) ............................ 109
IPC7 (Interrupt Priority Control 7) ............................ 110
MINSEC (RTCC Minutes and Seconds Value) ........ 188
MTHDY (RTCC Month and Day Value) ................... 187
NVMCON (Flash Memory Control) ............................ 69
NVMCON (Nonvolatile Memory Control) ................... 74
OSCCON (Oscillator Control) .................................. 123
OSCTUN (FRC Oscillator Tune) .............................. 126
PADCFG1 (Pad Configuration Control) ................... 171
RCFGCAL (RTCC Calibration
and Configuration) ........................................... 183
RCON (Reset Control) ............................................... 80
REFOCON (Reference Oscillator Control) ............... 129
RTCCSWT (RTCC Control/Sample
Window Timer) ................................................. 191
RTCPWC (RTCC Configuration 2) .......................... 185
SR (ALU STATUS) .............................................. 38, 89
SSPxADD (MSSPx Slave Address/Baud
Rate Generator) ............................................... 170
SSPxCON1 (MSSPx Control 1, I2C Mode) .............. 166
SSPxCON1 (MSSPx Control 1, SPI Mode) ............. 165
SSPxCON2 (MSSPx Control 2, I2C Mode) .............. 167
SSPxCON3 (MSSPx Control 3, I2C Mode) .............. 169
SSPxCON3 (MSSPx Control 3, SPI Mode) ............. 168
SSPxMSK (I2C Slave Address Mask) ...................... 170
SSPxSTAT (MSSPx Status, I2C Mode) ................... 163
SSPxSTAT (MSSPx Status, SPI Mode) .................. 162
DS33030A-page 328
T1CON (Timer1 Control) ......................................... 142
ULPWUCON (ULPWU Control) ............................... 133
UxMODE (UARTx Mode) ......................................... 176
UxRXREG (UARTx Receive) ................................... 180
UxSTA (UARTx Status and Control) ........................ 178
UxTXREG (UARTx Transmit) .................................. 180
WKDYHR (RTCC Weekday and Hours Value) ........ 188
YEAR (RTCC Year Value) ....................................... 187
Resets
Brown-out Reset (BOR) ............................................. 83
Clock Source Selection .............................................. 82
Delay Times ............................................................... 82
Device Times ............................................................. 82
Low Power BOR (LPBOR) ......................................... 83
RCON Flag Operation ............................................... 81
SFR States ................................................................ 83
Retention Regulator (RETREG) ...................................... 134
Revision History ............................................................... 323
RTCC ............................................................................... 181
Alarm Configuration ................................................. 192
Alarm Mask Settings (figure) ................................... 193
ALRMVAL Register Mappings ................................. 189
Calibration ............................................................... 192
Module Registers ..................................................... 182
Mapping ........................................................... 182
Clock Source Selection ........................... 182
Write Lock ........................................................ 182
Power Control .......................................................... 193
RTCVAL Register Mappings .................................... 187
Source Clock ........................................................... 181
S
Serial Peripheral Interface. See SPI Mode.
SFR Space ........................................................................ 44
Software Simulator (MPLAB SIM) ................................... 263
Software Stack ................................................................... 63
SPI Mode
I/O Pin Configuration ............................................... 159
T
Timer1 .............................................................................. 141
Timing Diagrams
A/D Conversion ........................................................ 295
Brown-out Reset Characteristics ............................. 284
Capture/Compare/PWM (MCCPx, SCCPx) ............. 285
CLKO and I/O Timing .............................................. 282
Example SPI Master Mode (CKE = 0) ..................... 286
Example SPI Master Mode (CKE = 1) ..................... 287
Example SPI Slave Mode (CKE = 0) ....................... 288
Example SPI Slave Mode (CKE = 1) ....................... 289
External Clock .......................................................... 280
I2C Bus Data ............................................................ 290
I2C Bus Start/Stop Bits ............................................ 290
MSSPx I2C Bus Data ............................................... 293
MSSPx I2C Bus Start/Stop Bits ............................... 292
Reset, Watchdog Timer. Oscillator Start-up Timer,
Power-up Timer Characteristics ...................... 283
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
Timing Requirements
A/D Conversion ........................................................ 295
Capture/Compare/PWM (MCCPx, SCCPx) ............. 285
CLKO and I/O .......................................................... 282
Comparator .............................................................. 285
Comparator Voltage Reference Settling Time ......... 285
External Clock .......................................................... 280
I2C Bus Data (Slave Mode) ...................................... 291
I2C Bus Data Requirements (Master Mode) ............ 293
I2C Bus Start/Stop Bits (Master Mode) .................... 292
I2C Bus Start/Stop Bits (Slave Mode) ...................... 290
PLL Clock Specifications ......................................... 281
SPI Mode (Master Mode, CKE = 0) ......................... 286
SPI Mode (Master Mode, CKE = 1) ......................... 287
SPI Mode (Slave Mode, CKE = 0) ........................... 288
SPI Slave Mode (CKE = 1) ...................................... 289
U
UART
Baud Rate Generator (BRG) ................................... 174
Break and Sync Transmit Sequence ....................... 175
IrDA Support ............................................................ 175
Operation of UxCTS and UxRTS Control Pins ........ 175
Receiving in 8-Bit or 9-Bit Data Mode ..................... 175
Transmitting in 8-Bit Data Mode .............................. 175
Transmitting in 9-Bit Data Mode .............................. 175
Universal Asynchronous Receiver
Transmitter (UART) ................................................. 173
V
Voltage Regulator (VREG) .............................................. 134
W
Watchdog Timer (WDT) ................................................... 257
Windowed Operation ............................................... 258
WWW Address ................................................................ 330
WWW, On-Line Support .................................................... 11
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 329
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 330
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://microchip.com/support
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 331
PIC24FV16KM204 FAMILY
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: PIC24FV16KM204 Family
Literature Number: DS33030A
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS33030A-page 332
Advance Information
 2013 Microchip Technology Inc.
PIC24FV16KM204 FAMILY
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PIC 24 FV 16 KM2 04 T - I / PT - XXX
Examples:
a)
PIC24FV16KM204-I/ML: Wide voltage range,
General Purpose, 16-Kbyte program memory,
44-pin, Industrial temp., QFN package
b)
PIC24F08KM102-I/SS: Standard voltage range,
General Purpose with reduced feature set,
8-Kbyte program memory, 28-pin, Industrial
temp., SSOP package
Microchip Trademark
Architecture
Flash Memory Family
Program Memory Size (Kbytes)
Product Group
Pin Count
Tape and Reel Flag (if applicable)
Temperature Range
Package
Pattern
Architecture
Flash Memory Family
24
= 16-bit modified Harvard without DSP
F
= Standard voltage range Flash program memory
FV
= Wide voltage range Flash program memory
Product Group
KM2 = General Purpose PIC24F Lite Microcontroller
KM1 = General Purpose PIC24F Lite Microcontroller with
Reduced Feature Set
Pin Count
01
02
04
= 20-pin
= 28-pin
= 44-pin
Temperature Range
I
E
= -40C to +85C (Industrial)
= -40C to +125C (Extended)
Package
SP
SO
SS
ML
P
PT
MV
=
=
=
=
=
=
=
Pattern
Three-digit QTP, SQTP, Code or Special Requirements
(blank otherwise)
ES = Engineering Sample
SPDIP
SOIC
SSOP
QFN
PDIP
TQFP
UQFN
 2013 Microchip Technology Inc.
Advance Information
DS33030A-page 333
PIC24FV16KM204 FAMILY
NOTES:
DS33030A-page 334
Advance Information
 2013 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. & KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2013, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-62076-994-2
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
 2013 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
Advance Information
DS33030A-page 335
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-213-7828
Fax: 886-7-330-9305
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS33030A-page 336
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Advance Information
11/29/12
 2013 Microchip Technology Inc.
Similar pages