NEC FGR0H105ZF Super capacitor Datasheet

Vol. 12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
FOR CORRECT USE OF SUPER CAPACITORS
1. Please confirm the operating conditions and the specifications of the
Super Capacitors befor using them.
2. The electrolyte of these Super Capacitors is sealed with material such as rubber.
When you use the capacitors for a long time at high temperature, the moisture of
the eleotrolyte evaporates and the equivalent series resistance (E.S.R.) increases.
The fundamental failure mode is the open mode depending on E.S.R. increase.
When using a capacitor, please introduce a safe design assuming unexpected capacitor failure, such as redundancy in design and protection from
fire and erroneous operation.
3. Please read 'Notes on Using the Super Capacitor' on page 60 when you design
the circuits using the Super Capacitors.
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
CONTENTS
page
1. Organization of Super Capacitor Series ……………………………………………………………
4
2. Performance for Selection
5
……………………………………………………………………………
3. Characteristics of Super Capacitor
…………………………………………………………………
5
4. Typical Applications
……………………………………………………………………………………
6
5. Part Number System
……………………………………………………………………………………
7
6. Rated Specifications
……………………………………………………………………………………
9
6.1 FC Series（SMD Type） …………………………………………………………………………
9
6.2 FM Series
………………………………………………………………………………………… 13
6.3 FG Series
………………………………………………………………………………………… 20
6.4 FT Series
………………………………………………………………………………………… 22
6.5 FY Series
………………………………………………………………………………………… 24
6.6 FR Series
………………………………………………………………………………………… 26
6.7 FS Series
………………………………………………………………………………………… 28
6.8 FA，FE Series …………………………………………………………………………………… 30
6.9 HV Series（High Capacitance Type）………………………………………………………… 32
7. Packing
…………………………………………………………………………………………………… 33
8. List of Plating Type and Sleeve Type
……………………………………………………………… 34
9. Measurement Conditions ……………………………………………………………………………… 35
10. Notes on Using Super Capacitor（Electric Double-Layer Capacitor） ……………………… 36
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
1. Organization of Super Capacitor Series
−25 to 70℃
guaranteed
−40 to 85℃
guaranteed
mA order
back-up
For automatic
mounting
（SMD）
（embossad taping）
μA order
back-up
FC
series
3.5 to 5.5V
FME
FML
For automatic
mounting
（radial taping）
Type
5.5V
FM
FMR
series
3.5 to 6.5V
Type
3.5 to 5.5V
FG
FGR
−40 to 85℃
guaranteed
FT
Can Case type
（self-supporting Type）
series
5.5V
FS
series
5.5 to 11V
series
3.5 to 5.5V
FY
series
3.5 to 5.5V
Type
5.5V
FR
series
5.5V
FE
series
5.5V
FA
series
5.5 to 11V
For A order
current
HV
series
2.7V
10 to 100F
4 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
mA
High power
SuperCapacitor
BOX type
Backup current
Low ESR
kA
A
High ESR
Backup current depends on SuperCapacitor
equivalent series resistance (ESR)
2. Performance for Selection
High power
SuperCapacitor
HV Series
Low impedance application use
FA, FE, FS, FT, FM Series
High impedance application use
FG, FY, FC, FM, FR Series
μA
0.01
0.1
1
102
10
103
1 minute
104
1 hour
105
106
1 day 1 week
107
108
Backup time
1 month
( sec )
Backup time depends on capacitance
3. Characteristics of Super Capacitor
Super Capacitor can not be used for applications in AC circuit such as ripple absorption because it has high internal resistance
(several hundred mΩ to a hundred Ω) compared to aluminum electrolysis capacitor. Thus its main use would be similar to that
of secondary battery such as power back-up in DC circuit. The following list shows the characteristics of Super Capacitors as
compared to aluminum electrolyses capacitors for power back-up and secondary batteries.
Secondary battery
NiCd battery
Capacitor
Lithium ion battery
Aluminum electrolysis capacito
Super Capacitor
Back-up ability
◎
◎
△
○
Eco-hazard
Cd
−−−
−−−
−−−
−20 to 60 ℃
−20 to 50 ℃
−55 to 105 ℃
−40 to 85 ℃（FR，FT）
few hours
few hours
few minutes
few minutes
Charge/discharge life time
approx. 500 times
approx. 500 to 1000 times
limitless (*1)
limitless (*1)
Restrictions on charge/discharge
yes
yes
none
none
not applicable
not applicable
applicable
applicable
Operating temperature range
Charge time
Flow soldering
Automatic mounting
Safety risks
not applicable
not applicable
applicable
applicable (FM and FC series)
leakage, explosion
leakage, combustion, explosion, ignition
heat-up, explosion
gas emission (*2)
(*1) Aluminum electrolysis capacitor and Super Capacitor has limited lifetime. However, when used under proper conditions, both can operate
sufficiently within the designed lifetime of the set they are built in.
(*2) There is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte (diluted sulfuric acid).
However, application of abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion.
Super Capacitors Vol.12 5
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
4. Typical Applications
As in the characteristics remarked previously, Super Capacitor has characteristics intermediate between general capacitors and
batteries. Because of this, Super Capacitor can be used like a secondary battery when applied to DC circuit. The best suited
applications of Super Capacitor are back-up device for the power shut-down of micro computers and RAM's. The list below
shows main application examples.
Application Examples of Super Capacitor
Intended use
(guideline)
Long time
back-up
Back-up for
1 hour or less
Power supply
(guideline)
Application
Examples of equipments
Series
・CMOS RAM, IC for clocks
・Measuring device, Control equipment,
Communication device,
Automotive power source
・FR series
(85 ℃ guaranteed)
・CMOS micro computer, IC for
clocks
・CMOS micro computer
・Static RAM/DTS
(digital tuning system)
・FC series
・FG series
・FY series
・FM series
・Micro computer, RAM
・VCR, Microwave oven,
・Micro computer
・Memory equipped device
・Driving motor
・VCR, Printer, Projector
・Video disk
・Subsidiary power supply for driving
motor during voltage drop
・Camera
・Power source of toys, LED, buzzer
・Toys, Display device, Alarm device
・High current supply for a short
amount of time
・Actuator, Relay solenoid, Gas igniter
・Power supply, Subsidiary power
supply
・Street sign, Display light , UPS
500μA and below
50 mA and below
Back-up for
10 seconds
or less
1 A and below
Power assist
Up to several A
・FT series
・FS series
・FA series
・FE series
・HV series
6 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
5. Part Number System
FM, FC, FT, FG, FS, FR, FY, FE, FA Series
FG Series bulk type
FG
0H
223
Z
F
Environmental pollutant reduced
Capacitance tolerance
＋80％, −20％
Nominal capacitance（μF）
First two digits represent significant figure
Third digit specifies number of zeroes to follow microfarad code.
Maximum operating voltage
0V：3.5Vdc, 0H：5.5Vdc, 0J：6.5Vdc, 1A：11Vdc, 1B：12Vdc
Series name
FM Series tape type (Ammo pack)
FM0H223ZF
TP
16
Height (excluding lead)
16：16mm
18：18mm
Tape type
Bulk part name
FC Series tape type (Embossed tape)
FC0H104ZF
TB
R
24 - SS
Indivisual management code
Tape width
Positive electrode position in relation to tapes forward direction
Embossed tape type
Bulk part name
Super Capacitors Vol.12 7
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
HV Series
HV
0E
106
N
F
Environmental pollutant reduced
Capacitance tolerance
±30％
Nominal capacitance（μF）
First two digits represent significant fifure
Third digit specifies number of zeroes to follow microfarad code.
Maximum operating voltage
0E：2.7Vdc
Series name
8 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6. Rated Specifications
6.1 FC Series
Features
Dimensions
• Enables surface mounting.
B±0.2
• High rated voltage of 5.5V.
D±0.5
• High leakage reliability.
A±0.2
H max.
Negative
terminal
L
W±0.1
K
I
P
Positive
terminal
I
Markings
Displays nominal capacitance, MAX operating voltage serial number, polarity and etc.
Polarity
(negative)
Nominal
capacitance
473
5.5V
A1
MAX
operating voltage
Date code
FC0H473ZFTBR24
FC0H104ZFTBR24
FC0H224ZFTBR24
FC0V104ZFTBR24
FC0V224ZFTBR24
FC0V474ZFTBR24
FCH0V683ZFTBR16
FCH0V433ZFTBR16
Series name
Polarity
(negative)
Date code
Logo
MAX
operating voltage
NT
FC 5.5V
474
A1-001
Nominal
capacitance
Polarity
(negative)
MAX
operating voltage
473
5.5V
A1 S
Nominal
capacitance
Serial number
FCS Type
Date code
FC0H474ZFTBR32-SS
FC0H105ZFTBR44-SS
FCS0H473ZFTBR24
FCS0H104ZFTBR24
FCS0H224ZFTBR24
FCS0V104ZFTBR24
FCS0V224ZFTBR24
FCS0V474ZFTBR24
Standard models
FC Type
Part Number
FC0H473ZFTBR24
FC0H104ZFTBR24
FC0H224ZFTBR24
FC0H474ZFTBR32-SS
FC0H105ZFTBR44-SS
FC0V104ZFTBR24
FC0V224ZFTBR24
FC0V474ZFTBR24
Max.
Nominal
Max.
Voltage
ESR current at
Operating Capacitance Max.
Holding
1kHz) 30
Voltage
Discharge (at(Ω)
minutes Characteristic
D
Min. (V)
(Vdc)
system (F)
(mA)
5.5
0.047
50
0.071
4.2
10.5
5.5
0.10
25
0.15
4.2
10.5
5.5
0.22
25
0.33
4.2
10.5
5.5
0.47
13
0.71
4.2
16.0
5.5
1.0
7
1.50
4.2
21.0
3.5
0.10
50
0.09
̶
10.5
3.5
0.22
25
0.20
̶
10.5
3.5
0.47
25
0.42
̶
10.5
Dimension (Unit:mm)
H
A
B
I
W
P
K
5.5
5.5
8.5
9.5
10.5
5.5
5.5
8.5
10.8
10.8
10.8
16.3
21.6
10.8
10.8
10.8
10.8
10.8
10.8
16.3
21.6
10.8
10.8
10.8
3.6±0.5
3.6±0.5
3.6±0.5
6.8±1.0
7.0±1.0
3.6±0.5
3.6±0.5
3.6±0.5
1.2
1.2
1.2
1.2
1.4
1.2
1.2
1.2
5.0
5.0
5.0
5.0
10.0
5.0
5.0
5.0
0.7±0.3
0.7±0.3
0.7±0.3
1.2±0.5
1.2±0.5
0.7±0.3
0.7±0.3
0.7±0.3
D
H
A
B
I
W
P
K
6.8
6.8
3.7
5.0
6.8
6.8
6.8
6.8
2.9±0.5
2.9±0.5
0.7
0.7
2.5
2.5
H
A
B
I
W
P
K
5.5
5.5
8.5
5.5
5.5
8.5
10.8
10.8
10.8
10.8
10.8
10.8
10.8
10.8
10.8
10.8
10.8
10.8
3.9±0.5
3.9±0.5
3.9±0.5
3.9±0.5
3.9±0.5
3.9±0.5
1.2
1.2
1.2
1.2
1.2
1.2
5.0
5.0
5.0
5.0
5.0
5.0
0.9±0.3
0.9±0.3
0.9±0.3
0.9±0.3
0.9±0.3
0.9±0.3
L
0
0
0
0
0
0
0
0
＋0.3
−0.1
＋0.3
−0.1
＋0.3
−0.1
＋0.5
−0.1
＋0.5
−0.1
＋0.3
−0.1
＋0.3
−0.1
＋0.3
−0.1
Weight
(g)
1.0
1.0
1.4
4.0
6.7
1.0
1.0
1.4
FCH Type
Max.
Nominal
Max.
Voltage
ESR current
Operating Capacitance Max.
at
Holding
1kHz) 30
Voltage
Discharge (at(Ω)
minutes Characteristic
(Vdc)
system (F)
(mA)
Min. (V)
FCH0V683ZFTBR16
3.6
0.068
40
0.062
̶
FCH0H433ZFTBR16
5.5
0.043
50
0.065
̶
Part Number
Dimension (Unit:mm)
L
0.7±0.3 0
0.7±0.3 0
＋0.3
−0.1
＋0.3
−0.1
Weight
(g)
0.3
0.4
FCS Type
Part Number
FCS0H473ZFTBR24
FCS0H104ZFTBR24
FCS0H224ZFTBR24
FCS0V104ZFTBR24
FCS0V224ZFTBR24
FCS0V474ZFTBR24
Max.
Nominal
Max.
Voltage
ESR current
Operating Capacitance Max.
at
Holding
1kHz) 30
Voltage
Discharge (at(Ω)
minutes Characteristic
D
(Vdc)
system (F)
(mA)
Min. (V)
5.5
0.047
100
0.071
4.2
10.7
5.5
0.10
50
0.15
4.2
10.7
5.5
0.22
50
0.33
4.2
10.7
3.5
0.10
100
0.09
̶
10.7
3.5
0.22
50
0.20
̶
10.7
3.5
0.47
50
0.42
̶
10.7
Dimension (Unit:mm)
L
0
0
0
0
0
0
＋0.3
−0.1
＋0.3
−0.1
＋0.3
−0.1
＋0.3
−0.1
＋0.3
−0.1
＋0.3
−0.1
Weight
(g)
1.0
1.0
1.4
1.0
1.0
1.4
Super Capacitors Vol.12 9
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Precautions for use
・This series is exclusively for reflow soldering. It is designed for thermal conduction system such as combination use of infrared
ray and heat blow. Consult with NEC TOKIN before applying other methods.
・The reflow condition must be kept within reflow profile graphs shown below.
・Applying reflow soldering is limited to 2 times. After the first reflow, cool down the capacitor thoroughly to 5-35 ℃ before the
second reflow.
Always consult with NEC TOKIN when applying reflow soldering in a more severe condition than the condition described here.
・FCS Type
・FC, FCH Type
Reflow profile
260℃
250
217℃
200℃
70sec
150℃
150
150sec
100
50
0
0
50
100
150
200
250
300
350
200
160 ℃
150
120sec
100
50
Tp Time exceeding 200℃
0
400
Time (sec)
Time (sec)
Peak temperature
Below 260 ℃
Over 255 ℃
Within 10sec.
Over 230 ℃
Within 45sec.
Over 220 ℃
Within 60sec.
Over 217 ℃
Within 70sec.
Time between 150 ℃ to
200 ℃（temperature zone
over 170 ℃ ＝within 50sec.）
150sec.
Tp Time exceeding 200℃
Peak temperature (℃)
・Above "Reflow Profile" graph indicates temperature at the
terminals and capacitor top.
Peak temperature :
235℃，within 10sec.
250
Temperature on the
capacitor top (℃)
Temperature (℃)
300
200
Peak temperature
Temperature on the
capacitor top
Reflow profile
250
240
230
220
210
200
0
10
20
30
Tp (sec)
40
50
60
・Above "Reflow Profile" graph indicates temperature at the
terminals and capacitor top.
10 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Tape and Reel Dimensions
[Reel Dimensions]
(mm)
E
Mark
TBR16
A
380±2
TBR24
380±2
C
80±1
B
B
D
R:10
t
A
W
Product height 5.5mm
80±1
Product height 8.5mm
100±1
TBR32
TBR44
330±2
380±2
100±1
100±1
C
13±0.5
13±0.5
13±0.5
13±0.5
D
21±0.8
21±0.8
21±0.8
21±0.8
E
2±0.5
2±0.5
2±0.5
2±0.5
W
17.5±1.0
t
2.0
Product height 5.5mm 25.5±0.5
Product height 8.5mm 25.5±1.0
33.5±1.0 45.5±1.0
2.0
2.0
2.0
TBR32
TBR44
Dimensions of indented [square-hole plastic tape]
TBR16/24
(mm)
Mark
TBR16
TBR24
E
FD0
W
16.0
24.0
32.0
44.0
F
A
7.2
11.4
18.0
23.0
25.0
P0
B
A
W
Sprocket hole
P2
t1
Forward direction
P1
TBR32/44
Super capacitors fitting
on square-hole
4.0
P1
12.0
16.0
24.0
32.0
2.0
2.0
2.0
2.0
7.5
11.5
14.2
20.2
φD0
1.55
1.55
1.55
1.55
t1
0.4
0.4
0.5
0.5
E
1.75
1.75
1.75
1.75
t2
5.0
10.0
12.0
G
–
28.4
40.4
W
B
G
t2
4.0
F
P0
A
20.0
4.0
P2
FD0
P2
t1
13.0
4.0
E
Super capacitors fitting
on square-hole
9.0
F
t2
Indented square-hole
for fitting super capacitors
B
P0
Product height 5.5mm
6.0
Product height 8.5mm
8.4
–
P1
R0.75
Recommended land pattern
0.2
Land pattern
Lead terminal
C
(mm)
Logo
B
A
B
(mm)
Part Number
FC0H473ZFTBR24
FC0H104ZFTBR24
FC0H224ZFTBR24
FC0H474ZFTBR32-SS
FC0H105ZFTBR44-SS
FC0V104ZFTBR24
FC0V224ZFTBR24
FC0V474ZFTBR24
A
5.0
5.0
5.0
5.0
10.0
5.0
5.0
5.0
B
4.6
4.6
4.6
10.0
10.5
4.6
4.6
4.6
C
2.5
2.5
2.5
2.5
3.5
2.5
2.5
2.5
Part Number
FC0H473ZFTBR24
FC0H104ZFTBR24
FC0H224ZFTBR24
FC0H474ZFTBR32-SS
FC0H105ZFTBR44-SS
FC0V104ZFTBR24
FC0V224ZFTBR24
FC0V474ZFTBR24
A
5.0
5.0
5.0
5.0
10.0
5.0
5.0
5.0
B
3.6
3.6
3.6
6.8
7.0
3.6
3.6
3.6
C
1.2
1.2
1.2
1.2
1.4
1.2
1.2
1.2
FCH0V683ZFTBR16
FCH0H433ZFTBR16
2.5
2.5
4.0
4.0
1.4
1.4
FCH0V683ZFTBR16
FCH0H433ZFTBR16
2.5
2.5
2.9
2.9
0.7
0.7
FCS0H473ZFTBR24
FCS0H104ZFTBR24
FCS0H224ZFTBR24
FCS0V104ZFTBR24
FCS0V224ZFTBR24
FCS0V474ZFTBR24
5.0
5.0
5.0
5.0
5.0
5.0
4.9
4.9
4.9
4.9
4.9
4.9
2.5
2.5
2.5
2.5
2.5
2.5
FCS0H473ZFTBR24
FCS0H104ZFTBR24
FCS0H224ZFTBR24
FCS0V104ZFTBR24
FCS0V224ZFTBR24
FCS0V474ZFTBR24
5.0
5.0
5.0
5.0
5.0
5.0
3.9
3.9
3.9
3.9
3.9
3.9
1.2
1.2
1.2
1.2
1.2
1.2
Super Capacitors Vol.12 11
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
FC
5.5V type, 3.5V type
Item
Test conditions (conforming to JIS C 5160-1)
Category temperature range
−25 ℃ to ＋70 ℃
MAX operating voltage
5.5Vdc, 3.5Vdc
Capacitance
Refer to standard ratings
Capacitance allowance
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
Refer to standard ratings
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Current (30-minutes value)
Refer to standard ratings
Refer to “Measurement Conditions”
Capacitance
More than 90% of initial ratings
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Surge voltage：4.0V (3.5V type, 3.6V type)
：6.3V (5.5V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.043F, 0.047F 300Ω
：0.068F
240Ω
：0.10F
150Ω
：0.22F
56Ω
：0.47F
30Ω
：1.0F
15Ω
Discharge resistance：0Ω
Temperature：70±2 ℃
*
Surge
*
Vibration resistance
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Appearance
No obvious abnormality
*
Solder heat resistance
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
*
Temperature cycle
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
*
Characteristics in
different temperature
*
High temp. and high
humidity resistance
*
High temperature load
Refer to “Measurement Conditions”
Phase 2
50% higher than initial value
400% or less than initial value
Phase 3
Phase 5
Phase 6
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±20% of initial value
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±30% of initial value
ESR
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Appearance
No obvious abnormality
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Cooled down to ambient temperature after reflow
soldering, then the product must fulfill the condition
stated left. (See page 10 for reflow condition)
Conforms to 4.12
Temperature condition：−25 ℃ →Room temperature→
＋70 ℃ →Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Charging
condition
*
Self discharge characteristics
(voltage holding characteristics)
5.5V type: Voltage between terminal leads
higher than 4.2V
3.5V type: Not specified
Storage
Voltage applied：5.0Vdc (Terminal
at the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Let stand for 24 hours in condition
described below with terminals
opened.
Ambient temperature：Lower than 25 ℃
Relative humidity：Lower than 70%RH
As for items with “*” , it must fulfill the above condition after the reflow soldering. (See page 10 for reflow conditions)
12 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.2 FM Series
Dimensions
10.5±0.5
T±0.5
11.5±0.5
0.4±0.1
5±1
0.5±0.1
0.4±0.1
5±0.5
（Unit：mm）
Markings
Negative polarity identification
NT
MAX operating
voltage
Nominal capacitance
5.5V
–
473
A1
+
E
E ：FME type marking
L ：FML type marking
R：FMR type marking
Date code
Polarity
Lead terminal forming example
Lead length designation
For transverse mounting ＜L1＞
Ｌ＝2.2 to 5mm
Super Capacitors Vol.12 13
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
5.5V Type
Nominal
capacitance
MAX ESR
（at 1 kHz）
（Ω）
MAX current
at 30 min.
（mA）
Voltage
holding
characteristics
（V）
T
（mm）
Weight
（g）
Bulk
Ammo pack
MAX
operating
voltage
（Vdc）
FM0H103ZF
FM0H103ZFTP（）
5.5
0.01
0.014
300
0.015
4.2
5.0
1.3
FM0H223ZF
FM0H223ZFTP（）
5.5
0.022
0.028
200
0.033
4.2
5.0
1.3
FM0H473ZF
FM0H473ZFTP（）
5.5
0.047
0.06
200
0.071
4.2
5.0
1.3
FM0H104ZF
FM0H104ZFTP（）
5.5
0.10
0.13
100
0.15
4.2
6.5
1.6
FM0H224ZF
FM0H224ZFTP（）
5.5
−
0.22
100
0.33
4.2
6.5
1.6
Part Number
Charge Discharge
system(F) system(F)
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"
3.5V Type
Part Number
Nominal
capacitance
Bulk
Ammo pack
MAX operating
voltage
（Vdc）
FM0V473ZF
FM0V473ZFTP（）
3.5
0.047
0.06
200
0.042
5.0
1.3
FM0V104ZF
FM0V104ZFTP（）
3.5
0.10
0.13
100
0.090
5.0
1.3
FM0V224ZF
FM0V224ZFTP（）
3.5
0.22
0.30
100
0.20
6.5
1.6
MAX ESR
（at 1 kHz）
（Ω）
MAX current at
30 min.
（mA）
T
（mm）
Weight
（g）
200
0.071
6.5
1.6
MAX ESR
（at 1 kHz）
（Ω）
MAX current at
30 min.
（mA）
T
（mm）
Weight
（g）
Charge
system(F)
Discharge
system(F)
MAX ESR
（at 1 kHz）
（Ω）
MAX current at
30 min.
（mA）
T
（mm）
Weight
（g）
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"
6.5V Type
Part Number
Bulk
Ammo pack
MAX operating
voltage
（Vdc）
FM0J473ZF
FM0J473ZFTP（）
6.5
Nominal
capacitance
Charge
system(F)
Discharge
system(F)
0.047
0.062
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"
FME, FML Type (Buckup Large Current, mA Order)
Part Number
Bulk
Ammo pack
MAX operating
voltage
（Vdc）
Nominal
capacitance
Charge
system(F)
Discharge
system(F)
FME0H223ZF FME0H223ZFTP（）
5.5
0.022
0.028
40
0.033
5.0
1.3
FME0H473ZF FME0H473ZFTP（）
5.5
0.047
0.06
20
0.071
5.0
1.3
FML0H333ZF
5.5
0.033
6.5
0.050
5.0
1.3
FML0H333ZFTP（）
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"
FMR Type (MAX Operating Temperature 85 ℃ Type)
Part Number
Bulk
Ammo pack
MAX
operating
voltage
（Vdc）
Nominal
capacitance
Charge Discharge
system(F) system(F)
0.062
MAX ESR
（at 1 kHz）
（Ω）
MAX current
at 30 min.
（mA）
Voltage
holding
characteristics
（V）
T
（mm）
Weight
（g）
FMR0H473ZF FMR0H473ZFTP（）
5.5
0.047
200
0.071
4.2
6.5
1.6
FMR0H104ZF FMR0H104ZFTP（）
5.5
0.10
50
0.15
4.2
6.5
1.6
FMR0V104ZF FMR0V104ZFTP（）
3.5
0.10
50
0.090
−
6.5
1.6
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"
14 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
FMC Type
Chip parts applicable to treatment in bond hardening furnace (160±5 ℃ for 120±10 seonds)
Dimensions
b ±0.5
T±0.5
a ±0.5
0.4±0.1
5±1
d1 ±0.1
d 2 ±0.1
5±0.5
（Unit：mm）
Markings
Negative polarity identification
NT
Nominal capacitance
MAX operating
voltage
5.5V
–
473
K1
+
C
C：FMC type marking
Date code
Polarity
Specifications
Part Number
Bulk
Ammo pack
Nominal
Voltage
MAX
MAX
a
MAX ESR
holding
operating capacitance
current at
（at 1 kHz）
characteristics
voltage
30
min.
Charge Discharge
(mm)
（Ω）
（V）
（Vdc） system(F) system(F)
（mA）
b
T
d1
d2
Weight
(mm)
(mm)
(mm)
(mm)
（g）
FMC0H473ZF FMC0H473ZFTP（）
5.5
0.047
0.06
100
0.071
4.2
11.5
10.5
5.0
0.5
0.4
1.3
FMC0H104ZF FMC0H104ZFTP（）
5.5
0.10
0.13
50
0.15
4.2
11.5
10.5
6.5
0.5
0.4
1.6
FMC0H334ZF FMC0H334ZFTP（）
5.5
–
0.33
25
0.50
4.2
15.0 14.0
9.0
0.6
0.6
3.5
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"
Super Capacitors Vol.12 15
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Taping Specification [except FMC0H334ZFTP( )]
P
P2
Δh
b
a
c
−
F
＋
W4
H
t3
W
W0
W1
L
P1
＋
W2
−
P0
D0
t2
t1
（Unit：mm）
Item
Symbol
Value
Tolerance
Component Height
a
11.5
±0.5
Component Width
b
10.5
±0.5
Component Thickness
c
−
±0.5
W4
0.5
±0.1
Lead-wire Thickness
t3
0.4
±0.1
Pitch between Component
P
12.7
±1.0
Sprocket Hole Pitch
P0
12.7
±0.3
Lead-wire Width
Sprocket Hole to Lead
〃
Lead Spacing
Component Alignment
P1
3.85
±0.7
P2
6.35
±1.3
F
5.0
±0.5
Δh
2.0 Max.
−
＋1.0
−0.5
Tape Width
W
18.0
Hold-down tape Width
W0
12.5 Min.
−
Sprocket Hole Position
W1
9.0
±0.5
Hold-down Tape Position
W2
3.0 Max.
−
16.0
±0.5
Component's Bottom Line Position
〃
Sprocket Hole Diameter
Total tape Thickness
〃
Defect Component Cut-off Position
H
D0
18.0
±0.5
φ4.0
±0.2
t1
0.7
±0.2
t2
1.5 Max.
−
L
11.0 Max.
−
Remarks
5.5 V type
3.5 V type
FME type
FML type
6.5 V type
FMR type
FMC type
: 5.0/0.010F to 0.047F, 6.5/0.047F
: 5.0/0.047F to 0.10F, 6.5/0.22F
: 5.0/0.022F to 0.047F
: 5.0/0.033F
: 6.5/0.047F, 0.10F
: 6.5/0.047F
: 5.0/0.047F, 6.5/0.10F
Including tilting caused by bending lead wire.
No protrusion of tape.
16 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Taping Specification [except FMC0H334ZFTP ( )]
P
P2
Δh
b
a
c
−
F
＋
W4
t3
W
W0
W1
L
H
P1
＋
W2
−
D0
P0
t2
t1
（Unit：mm）
Item
Symbol
Value
Tolerance
Component Height
a
15.0
±0.5
Component Width
b
14.0
±0.5
Component Thickness
c
9.0
±0.5
W4
0.6
±0.1
Lead-wire Width
Lead-wire Thickness
t3
0.6
±0.1
Pitch between Component
P
25.4
±1.0
Sprocket Hole Pitch
P0
12.7
±0.3
Sprocket Hole to Lead
P1
3.85
±0.7
P2
6.35
±1.3
F
5.0
±0.5
Δh
2.0 Max.
−
＋1.0
−0.5
〃
Lead Spacing
Component Alignment
Tape Width
W
18.0
Hold-down tape Width
W0
12.5 Min.
−
Sprocket Hole Position
W1
9.0
±0.5
Hold-down Tape Position
W2
3.0 Max.
−
16.0
±0.5
Component's Bottom Line Position
〃
Sprocket Hole Diameter
Total tape Thickness
〃
Defect Component Cut-off Position
H
D0
18.0
±0.5
φ4.0
±0.2
t1
0.67
±0.2
t2
1.7 Max.
−
L
11.0 Max.
−
Remarks
Including tilting caused by bending lead wire
No protrusion of tape
Super Capacitors Vol.12 17
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
Item
5.5V type, 3.5V type, 6.5V type
FMC type
FML, FME type
Test conditions
(conforming to JIS C 5160-1)
Category temperature range
−25 ℃ to ＋70 ℃
−25 ℃ to ＋70 ℃
MAX operating voltage
5.5Vdc, 3.5Vdc, 6.5Vdc
5.5Vdc
Capacitance
5.5V：0.010F to 0.33F
3.5V：0.047F to 0.22F
6.5V：0.047
0.022F, 0.033F, 0.047F
Refer to “Measurement Conditions”
Capacitance allowance
＋80 ％, −20 ％
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
Refer to standard ratings
Refer to standard ratings
Measured at 1kHz, 10mA ; See also
“Measurement Conditions”
Current (30-minutes value)
Refer to standard ratings
Refer to standard ratings
Refer to “Measurement Conditions”
Capacitance
More than 90% of initial ratings
More than 90% of initial ratings
ESR
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Surge voltage：4.0V (3.5V type)
：6.3V (5.5V type)
：7.4V (6.5V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.010F
1500Ω
：0.022F
560Ω
：0.033F
510Ω
：0.047F
300Ω
240Ω
：0.068F
：0.10F
150Ω
：0.22F
56Ω
：0.33F
51Ω
Discharge resistance：0Ω
Temperature：70±2 ℃
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Phase
2
Surge
Characteristics
in different
temperature
Lead strength (tensile)
Vibration
resistance
Temperature
cycle
High temp. and
high humidity
resistance
High
temperature
load
Phase
3
Phase
5
Phase
6
Phase
2
50% or higher than initial value
400% or less than initial value
Phase
3
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Phase
5
Phase
6
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should
be covered by the new solder
Over 3/4 of the terminal should
be covered by the new solder
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Capacitance
Within ±20% of initial value
Within ±20% of initial value
ESR
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Capacitance
Within ±30% of initial value
Within ±30% of initial value
ESR
Below 200% of initial ratings
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Below 200% of initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Solderability
Solder heat
resistance
50% or higher than initial value
400% or less than initial value
Self discharge characteristics
(voltage holding characteristics)
5.5V type: Voltage between
terminal leads higher
than 4.2V
3.5V type: Not specified
6.5V type: Not specified
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−25℃→Room temperature→
＋70℃→Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：70±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Charging
condition
Storage
Voltage applied：5.0Vdc (Terminal at
the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Let stand for 24 hours in condition
described below with terminals opened.
Ambient temperature：Lower than 25℃
Relative humidity：Lower than 70%RH
18 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
FMR type
Item
Test conditions (conforming to JIS C 5160-1)
Category temperature range
−40 ℃ to ＋85 ℃
MAX operating voltage
5.5Vdc, 3.5Vdc
Capacitance
0.047F, 0.10F
Refer to “Measurement Conditions”
Capacitance allowance
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
Refer to standard ratings
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Current (30-minutes value)
Refer to standard ratings
Refer to “Measurement Conditions”
Capacitance
More than 90% of initial ratings
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Surge voltage：4.0V (3.5V type)
：6.3V (5.5V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.047F 300Ω
：0.10F
150Ω
Discharge resistance：0Ω
Temperature：85±2 ℃
Surge
Characteristics in
different temperature
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration resistance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
Phase 3
Phase 5
Phase 6
50% or higher than initial value
400% or less than initial value
30% or higher than initial value
Below 700% of the initial value
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase3：−40±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should be covered by
the new solder
Solderability
Solder heat resistance
Phase 2
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±20% of initial value
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±30% of initial value
ESR
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Appearance
No obvious abnormality
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−40 ℃ →Room temperature→
＋85 ℃ →Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：85±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Charging
condition
Self discharge characteristics
(voltage holding characteristics)
5.5V type: Voltage between terminal leads
higher than 4.2V
3.5V type: Not specified
Storage
Voltage applied：5.0Vdc (Terminal
at the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Let stand for 24 hours in condition
described below with terminals
opened.
Ambient temperature：Lower than 25 ℃
Relative humidity：Lower than 70%RH
Super Capacitors Vol.12 19
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.3 FG Series
Dimensions
Markings on sleeve
Sleeve
A1
Date
code
0.3 MIN.
H MAX.
ℓMIN.
F D ± 0.5
001
Serial
number
Super Capacitor
FG 5.5 V
FG 5.5 V
0.22 F
0.22 F
A1
P ± 0.5
○ ○
−
＋
MAX
operating
voltage
Nominal
capacitance
Negative polarity
identification mark
d1 ± 0.1
d2 ± 0.1
（Terminal）
FG Type
Specifications
Part Number
MAX
operating
voltage
（Vdc）
MAX
Voltage
MAX ESR
current at
holding
（at
1
kHz）
Discharge
30 min. characteristics
（Ω）
system (F)
（mA）
（V）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
Weight
φD
H
P
ℓ
d1
d2
（g）
FG0H103ZF
5.5
0.010
0.013
300
0.015
4.2
11.0
5.5
5.08
2.7
0.2
1.2
0.9
FG0H223ZF
5.5
0.022
0.028
200
0.033
4.2
11.0
5.5
5.08
2.7
0.2
1.2
1.0
FG0H473ZF
5.5
0.047
0.060
200
0.071
4.2
11.0
5.5
5.08
2.7
0.2
1.2
1.0
FG0H104ZF
5.5
0.10
0.13
100
0.15
4.2
11.0
6.5
5.08
2.7
0.2
1.2
1.3
FG0H224ZF
5.5
0.22
0.28
100
0.33
4.2
13.0
9.0
5.08
2.2
0.4
1.2
2.5
FG0H474ZF
5.5
0.47
0.60
120
0.71
4.2
14.5
18.0
5.08
2.4
0.4
1.2
5.1
FG0H105ZF
5.5
1.0
1.3
65
1.5
4.2
16.5
19.0
5.08
2.7
0.4
1.2
7.0
FG0H225ZF
5.5
2.2
2.8
35
3.3
4.2
21.5
19.0
7.62
3.0
0.6
1.2
12.1
FG0H475ZF
5.5
4.7
6.0
35
7.1
4.2
28.5
22.0
10.16
6.1
0.6
1.4
27.3
FG0V155ZF
3.5
1.5
2.2
65
1.5
−
16.5
14.0
5.08
3.1
0.4
1.2
5.2
FGH Type
Specifications
Part Number
MAX
operating
voltage
（Vdc）
MAX
Voltage
MAX ESR
current at
holding
（at
1
kHz）
Discharge
30 min. characteristics
（Ω）
system (F)
（mA）
（V）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
Weight
φD
H
P
ℓ
d1
d2
（g）
FGH0H104ZF
5.5
−
0.10
100
0.15
4.2
11.0
5.5
5.08
2.7
0.2
1.2
1.0
FGH0H224ZF
5.5
−
0.22
100
0.33
4.2
11.0
7.0
5.08
2.7
0.2
1.2
1.3
FGH0H474ZF
5.5
−
0.47
65
0.71
4.2
16.5
8.0
5.08
2.7
0.4
1.2
4.1
FGH0H105ZF
5.5
−
1.0
35
1.5
4.2
21.5
9.5
7.62
3.0
0.6
1.2
7.2
FGR Type
Specifications
Part Number
MAX
operating
voltage
（Vdc）
MAX
Voltage
MAX ESR
current at
holding
（at
1
kHz）
Discharge
30 min. characteristics
（Ω）
system (F)
（mA）
（V）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
Weight
φD
H
P
ℓ
d1
d2
（g）
5.1
FGR0H474ZF
5.5
0.47
0.60
120
0.71
4.2
14.5
18.0
5.08
2.4
0.4
1.2
FGR0H105ZF
5.5
1.0
1.3
65
1.5
4.2
16.5
19.0
5.08
2.7
0.4
1.2
7.0
FGR0H225ZF
5.5
2.2
2.8
35
3.3
4.2
21.5
19.0
7.62
3.0
0.6
1.2
12.1
20 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
Item
Category temperature range
MAX operating voltage
FG, FGH type
FGR type
Capacitance allowance
−25 ℃ to ＋70 ℃
5.5Vdc, 3.5Vdc
FG：0.010F to 4.7F
FGH：0.10F to 1.0F
＋80 ％, −20 ％
ESR
Refer to standard ratings
Refer to standard ratings
Current (30-minutes value)
Capacitance
ESR
Current (30 minutes value)
Refer to standard ratings
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Refer to standard ratings
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
No obvious abnormality
No obvious abnormality
Capacitance
−40 ℃ to ＋85 ℃
5.5Vdc
0.47F to 2.2F
Refer to “Measurement Conditions”
＋80 ％, −20 ％
Refer to “Measurement Conditions”
Measured at 1kHz, 10mA ; See also
“Measurement Conditions”
Refer to “Measurement Conditions”
Surge voltage：6.3V (5.5V type)
：4.0V(3.5V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.010F
1500Ω
：0.022F
560Ω
：0.047F
300Ω
：0.10F
150Ω
：0.22F
56Ω
：0.47F
30Ω
：1.0F, 1.5F
15Ω
：2.2F, 4.7F
10Ω
Discharge resistance：0Ω
Temperature：85±2 ℃ (FGR)
：70±2 ℃ (FG, FGH)
Surge
Appearance
Capacitance
ESR
Capacitance
ESR
Characteristics
Capacitance
in different
ESR
temperature
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Capacitance
ESR
Vibration
resistance
Current (30 minutes value)
Appearance
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Phase
Satisfy initial ratings
6
Satisfy initial ratings
No terminal damage
50% or higher than initial value
400% or less than initial value
Phase 30% or higher than initial value
3
700% or less than initial value
200% or less than initial value
Phase
Satisfy initial ratings
5
1.5CV (mA) or below
Within ±20% of initial value
Phase
Satisfy initial ratings
6
Satisfy initial ratings
No terminal damage
Satisfy initial ratings
Satisfy initial ratings
No obvious abnormality
No obvious abnormality
Solderability
Over 3/4 of the terminal should
be covered by the new solder
Over 3/4 of the terminal should
be covered by the new solder
Satisfy initial ratings
Satisfy initial ratings
No obvious abnormality
No obvious abnormality
Satisfy initial ratings
Satisfy initial ratings
No obvious abnormality
Within ±20% of initial value
Not to exceed 120% of initial
ratings
Not to exceed 120% of initial
ratings
No obvious abnormality
Within ±30% of initial value
Below 200% of initial ratings
Below 200% of initial ratings
No obvious abnormality
No obvious abnormality
Within ±20% of initial value
Not to exceed 120% of initial
ratings
Not to exceed 120% of initial
ratings
No obvious abnormality
Within ±30% of initial value
Below 200% of initial ratings
Below 200% of initial ratings
No obvious abnormality
Solder heat
resistance
Temperature
cycle
High temp. and
high humidity
resistance
High
temperature
load
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Self discharge characteristics
(voltage holding characteristics)
Phase
2
50% or higher than initial value
400% or less than initial value
Phase
3
Phase
5
5.5V type: Voltage between
terminal leads higher
than 4.2V
3.5V type: Not specified
Test conditions
(conforming to JIS C 5160-1)
Phase
2
Conforms to 4.17
Phase1 ：＋25±2 ℃
Phase2 ：−25±2 ℃
Phase3 ：−40±2 ℃ (FGR)
Phase4 ：＋25±2 ℃
Phase5 ：＋70±2 ℃ (FG, FGH)
：＋85±2 ℃ (FGR)
Phase6 ：＋25±2 ℃
Conforms to 4.9
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：Category MIN temp→Room temp→
Category MAX temp→Room temp
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temp：Category MAX temp ±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Charging
condition
Voltage applied：5.0Vdc (Terminal at
the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Storage
Let stand for 24 hours in condition
described below with terminals opened.
Ambient temperature：Lower than 25℃
Relative humidity：Lower than 70%RH
Voltage between terminal leads
higher than 4.2V
Super Capacitors Vol.12 21
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.4 F T Series
Dimensions
Markings on sleeve
Sleeve
Date
code
0.3 MIN.
H MAX.
ℓMIN.
F D ± 0.5
Serial
number
A1
001
Super Capacitor
FT
5.5 V
FT
A1 85℃ 0.22 F
MAX
operating voltage
5.5 V
Nominal
capacitance
85℃ 0.22 F
Negative polarity
identification mark
P ± 0.5
○ ○
−
＋
d1 ± 0.1
d2 ± 0.1
（Terminal）
Specifications
Part Number
MAX
operating
voltage
（Vdc）
Nominal capacitance
Charge
system (F)
Discharge
system (F)
MAX ESR MAX current
（at 1 kHz） at 30 min.
（Ω）
（mA）
Dimension (unit:mm)
φD
Weight
H
P
d1
d2
ℓ
（g）
FT0H104ZF
5.5
0.10
0.14
16
0.15
11.5
8.5
5.08
0.4
1.2
2.7
1.6
FT0H224ZF
5.5
0.22
0.28
10
0.33
14.5
12.0
5.08
0.4
1.2
2.2
4.1
FT0H474ZF
5.5
0.47
0.60
6.5
0.71
16.5
13.0
5.08
0.4
1.2
2.7
5.3
FT0H105ZF
5.5
1.0
1.3
3.5
1.5
21.5
13.0
7.62
0.6
1.2
3.0
10.0
FT0H225ZF
5.5
2.2
2.8
1.8
3.3
28.5
14.0
10.16
0.6
1.4
6.1
18.0
FT0H335ZF
5.5
3.3
4.2
1.0
5.0
36.5
15.0
15.00
0.6
1.7
6.1
38.0
FT0H565ZF
5.5
5.6
7.2
0.6
8.4
44.5
17.0
20.00
1.0
1.4
6.1
72.0
22 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
FT type
Item
Category temperature range
−40 ℃ to ＋85 ℃
MAX operating voltage
5.5Vdc
Test conditions (conforming to JIS C 5160-1)
Capacitance
0.1F to 5.6F
Capacitance allowance
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
Refer to standard ratings
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Refer to standard ratings
Refer to “Measurement Conditions”
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Surge voltage：6.3V
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.10F
：0.22F
：0.47F
：1.0F
：2.2F
：3.3F
：5.6F
Discharge resistance：0Ω
Temperature：85±2 ℃
Current (30-minutes value)
Capacitance
ESR
Current (30 minutes value)
Refer to “Measurement Conditions”
Surge
Appearance
Characteristics in
different temperature
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration resistance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
Phase 2
Phase 3
Phase 5
Phase 6
50% or higher than initial value
400% or less than initial value
30% or higher than initial value
700% or less than initial value
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase3：−40±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should be covered by
the new solder
Solderability
Solder heat resistance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±20% of initial value
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±30% of initial value
ESR
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Appearance
No obvious abnormality
150Ω
56Ω
30Ω
15Ω
10Ω
10Ω
10Ω
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−40 ℃ →Room temperature→
＋85 ℃ →Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：85±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Super Capacitors Vol.12 23
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.5 FY Series
H MAX.
（H ± 0.5 for FYL）
Dimensions
Markings on sleeve
Sleeve
Date
code
0.3 MIN.
ℓMIN.
F D ± 0.5
Serial
number
A1
001
FYD 5.5 V
FYD 5.5 V
0.047 F
0.047 F
MAX
operating voltage
Nominal
capacitance
A1
P ± 0.5
○ ○
−
＋
Negative polarity
identification mark
d1 ± 0.1
d2 ± 0.1
（Terminal）
FYD Type
Specifications
Part Number
MAX
operating
voltage
（Vdc）
MAX
Voltage
MAX ESR
current at
holding
（at
1
kHz）
Discharge
30 min. characteristics
（Ω）
system (F)
（mA）
（V）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
Weight
φD
H
P
ℓ
d1
d2
（g）
FYD0H223ZF
5.5
0.022
0.033
220
0.033
4.2
11.5
8.5
5.08
2.7
0.4
1.2
1.6
FYD0H473ZF
5.5
0.047
0.070
220
0.071
4.2
11.5
8.5
5.08
2.7
0.4
1.2
1.7
FYD0H104ZF
5.5
0.10
0.14
100
0.15
4.2
13.0
8.5
5.08
2.2
0.4
1.2
2.4
FYD0H224ZF
5.5
0.22
0.35
120
0.33
4.2
14.5
15.0
5.08
2.4
0.4
1.2
4.3
FYD0H474ZF
5.5
0.47
0.75
65
0.71
4.2
16.5
15.0
5.08
2.7
0.4
1.2
6.0
FYD0H105ZF
5.5
1.0
1.6
35
1.5
4.2
21.5
16.0
7.62
3.0
0.6
1.2
11.0
FYD0H145ZF
5.5
1.4
2.1
45
2.1
4.2
21.5
19.0
7.62
3.0
0.6
1.2
12.0
FYD0H225ZF
5.5
2.2
3.3
35
3.3
4.2
28.5
22.0
10.16
6.1
0.6
1.4
22.9
FYH Type
Specifications
Part Number
MAX
operating
voltage
（Vdc）
MAX
Voltage
MAX ESR
current at
holding
Discharge （at 1 kHz） 30 min.
characteristics
（Ω）
system (F)
（mA）
（V）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
φD
H
P
ℓ
Weight
d1
d2
（g）
FYH0H223ZF
5.5
0.022
0.033
200
0.033
4.2
11.5
7.0
5.08
2.7
0.4
1.2
1.5
FYH0H473ZF
5.5
0.047
0.075
100
0.071
4.2
13.0
7.0
5.08
2.2
0.4
1.2
2.2
FYH0H104ZF
5.5
0.10
0.16
50
0.15
4.2
16.5
7.5
5.08
2.7
0.4
1.2
3.4
FYH0H224ZF
5.5
0.22
0.30
60
0.33
4.2
16.5
9.5
5.08
2.7
0.4
1.2
3.6
FYH0H474ZF
5.5
0.47
0.70
35
0.71
4.2
21.5
10.0
7.62
3.0
0.6
1.2
7.2
FYH0H105ZF
5.5
1.0
1.5
20
1.5
4.2
28.5
11.0
10.16
6.1
0.6
1.4
13.9
FGL Type
Specifications
Part Number
MAX
operating
voltage
（Vdc）
MAX
Voltage
MAX ESR
current at
holding
（at
1
kHz）
Discharge
30 min. characteristics
（Ω）
system (F)
（mA）
（V）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
Weight
φD
H
P
ℓ
d1
d2
（g）
FYL0H103ZF
5.5
0.01
0.013
300
0.015
4.2
11.0
5.0
5.08
2.7
0.2
1.2
0.9
FYL0H223ZF
5.5
0.022
0.028
200
0.033
4.2
11.0
5.0
5.08
2.7
0.2
1.2
1.0
FYL0H473ZF
5.5
0.047
0.061
200
0.071
4.2
12.0
5.0
5.08
2.7
0.2
1.2
1.2
24 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
Item
FY type (FYD, FYH, FYL)
Test conditions (conforming to JIS C 5160-1)
Category temperature range
−25 ℃ to ＋70 ℃
MAX operating voltage
5.5Vdc
Capacitance
Refer to standard ratings
Refer to “Measurement Conditions”
Capacitance allowance
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
FYD：0.022F to 2.2F
FYH：0.022F to 1.0F
FYL ：0.010F to 0.047F
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Current (30-minutes value)
Refer to standard ratings
Refer to “Measurement Conditions”
Capacitance
More than 90% of initial ratings
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Surge voltage：6.3V
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.010F
：0.022F
：0.047F
：0.068F
：0.10F
：0.22F
：0.47F
：1.0F, 1.4F
：2.2F
Discharge resistance：0Ω
Temperature：70±2 ℃
Surge
Characteristics in
different temperature
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration resistance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
50% or higher than initial value
400% or less than initial value
Phase 3
Phase 5
Phase 6
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should be covered by
the new solder
Solderability
Solder heat resistance
Phase 2
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±20% of initial value
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±30% of initial value
ESR
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Appearance
No obvious abnormality
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−25 ℃ →Room temperature→
＋70 ℃ →Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：70±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Charging
condition
Self discharge characteristics
(voltage holding characteristics)
1500Ω
560Ω
300Ω
240Ω
150Ω
56Ω
30Ω
15Ω
10Ω
Voltage between terminal leads higher than 4.2V
Storage
Voltage applied：5.0Vdc (Terminal
at the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Let stand for 24 hours in condition
described below with terminals opened.
Ambient temperature：Lower than 25 ℃
Relative humidity：Lower than 70%RH
Super Capacitors Vol.12 25
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.6 FR Series
Dimensions
Markings on sleeve
Sleeve
Date
code
0.3 MIN.
H MAX.
ℓMIN.
F D ± 0.5
A1
001 FR
Serial
number
5.5 V
FR
85℃ 0.022 F
5.5 V
85℃ 0.022 F
A1
MAX
operating voltage
Nominal
capacitance
Negative polarity
identification mark
P ± 0.5
○ ○
−
＋
d1 ± 0.1
d2 ± 0.1
（Terminal）
Specifications
Part Number
MAX
operating
voltage
（Vdc）
Voltage
MAX
MAX ESR
holding
current at
（at
1
kHz）
Discharge
30 min. characteristics
（Ω）
system (F)
（V）
（mA）
Dimension (unit:mm)
Nominal capacitance
Charge
system (F)
φD
H
P
Weight
ℓ
d1
d2
（g）
FR0H223ZF
5.5
0.022
0.028
220
0.033
4.2
11.5
14.0
5.08
2.7
0.4
1.2
2.3
FR0H473ZF
5.5
0.047
0.060
110
0.071
4.2
14.5
14.0
5.08
2.4
0.4
1.2
3.9
FR0H104ZF
5.5
0.10
0.15
150
0.15
4.2
14.5
15.5
5.08
2.4
0.4
1.2
4.3
FR0H224ZF
5.5
0.22
0.33
180
0.33
4.2
14.5
21.0
5.08
2.4
0.4
1.2
5.3
FR0H474ZF
5.5
0.47
0.75
100
0.71
4.2
16.5
21.5
5.08
2.7
0.4
1.2
7.5
FR0H105ZF
5.5
1.0
1.6
60
1.5
4.2
21.5
22.0
7.62
3.0
0.6
1.2
13.3
26 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
FR type
Item
Test conditions (conforming to JIS C 5160-1)
Category temperature range
−40 ℃ to ＋85 ℃
MAX operating voltage
5.5Vdc
Capacitance
0.022F to 1.0F
Refer to “Measurement Conditions”
Capacitance allowance
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
Refer to standard ratings
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Current (30-minutes value)
Capacitance
ESR
Current (30 minutes value)
Refer to standard ratings
Refer to “Measurement Conditions”
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Surge voltage：6.3V (5.5V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.022F
：0.047F
：0.068F
：0.10F
：0.22F
：0.47F
：1.0F
Discharge resistance：0Ω
Temperature：70±2 ℃
Surge
Appearance
Characteristics in
different temperature
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration resistance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
Phase 2
Phase 3
Phase 5
Phase 6
50% or higher than initial value
400% or less than initial value
30% or higher than initial value
700% or less than initial value
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase3：−40±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should be covered by
the new solder
Solderability
Solder heat resistance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±20% of initial value
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
Within ±30% of initial value
ESR
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Appearance
No obvious abnormality
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−40 ℃ →Room temperature→
＋85 ℃ →Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：85±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Charging
condition
Self discharge characteristics
(voltage holding characteristics)
560Ω
300Ω
240Ω
150Ω
56Ω
30Ω
15Ω
Voltage between terminal leads higher than 4.2V
Storage
Voltage applied：5.0Vdc (Terminal
at the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Let stand for 24 hours in condition
described below with terminals opened.
Ambient temperature：Lower than 25 ℃
Relative humidity：Lower than 70%RH
Super Capacitors Vol.12 27
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.7 FS Series
Dimensions
Markings on sleeve
Sleeve
Date
code
Serial
number
0.3 MIN.
H MAX.
ℓMIN.
F D ± 0.5
A1
001
FS
A1
5.5 V
FS
0.22 F
5.5 V
0.22 F
MAX
operating voltage
Nominal
capacitance
Negative polarity
identification mark
P ± 0.5
− ○
○
＋
d1 ± 0.1
d2 ± 0.1
（Terminal）
Specifications
Part Number
MAX
operating
voltage
（Vdc）
Nominal capacitance
Charge
system (F)
Discharge
system (F)
MAX ESR MAX current
（at 1 kHz） at 30 min.
（Ω）
（mA）
Dimension (unit:mm)
φD
H
P
ℓ
Weight
d1
d2
（g）
FS0H223ZF
5.5
0.022
0.033
60.0
0.033
11.5
8.5
5.08
2.7
0.4
1.2
1.6
FS0H473ZF
5.5
0.047
0.072
40.0
0.071
13.0
8.5
5.08
2.2
0.4
1.2
2.6
FS0H104ZF
5.5
0.10
0.15
25.0
0.15
16.5
8.5
5.08
2.7
0.4
1.2
4.1
FS0H224ZF
5.5
0.22
0.33
25.0
0.33
16.5
13.0
5.08
2.7
0.4
1.2
5.3
FS0H474ZF
5.5
0.47
0.75
13.0
0.71
21.5
13.0
7.62
3.0
0.6
1.2
10
FS0H105ZF
5.5
1.0
1.3
7.0
1.5
28.5
14.0
10.16
6.1
0.6
1.4
18
FS1A474ZF
11.0
0.47
0.60
7.0
1.41
28.5
25.5
10.16
6.1
0.6
1.4
32
FS1A105ZF
11.0
1.0
1.3
7.0
3.0
28.5
31.5
10.16
6.1
0.6
1.4
35
FS1B105ZF
12.0
1.0
1.3
7.5
3.6
28.5
38.0
10.16
6.1
0.6
1.4
40
FS1B505ZF
12.0
5.0
6.5
4.0
18.0
44.8
60.0
20.00
9.5
1.0
1.4
160
28 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
FS type
Item
Test conditions (conforming to JIS C 5160-1)
Category temperature range
−25 ℃ to ＋70 ℃
MAX operating voltage
5.5Vdc, 11Vdc, 12Vdc
Capacitance
5.5V：0.022F to 1.0F
11V：0.47, 1.0
12V：1.0F, 5.0F
Capacitance allowance
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
5.5V：0.0022F to 1.0F
11V：0.47F, 1.0F
12V：1.0F, 5.0F
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Refer to standard ratings
Refer to “Measurement Conditions”
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Surge voltage：6.3V (5.5V type)
：12.6V (11V type)
：13.6V (12V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.022F
：0.047F
：0.10F
：0.22F
：0.47F
：1.0F
：5.0F
Discharge resistance：0Ω
Temperature：70±2 ℃
Current (30-minutes value)
Capacitance
ESR
Current (30 minutes value)
Surge
Appearance
Characteristics in
different temperature
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration resistance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
Phase 2
Phase 3
Phase 5
Phase 6
560Ω
300Ω
150Ω
56Ω
30Ω
15Ω
10Ω
50% or higher than initial value
300% or less than initial value
150% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should be covered by
the new solder
Solderability
Solder heat resistance
No obvious abnormality
Refer to “Measurement Conditions”
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
Over 90% of the initial value (5.5V type)
Within ±20% of initial value (11V type, 12Vtype)
ESR
Not to exceed 120% of initial ratings
Current (30 minutes value)
Not to exceed 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
Over 85% of the initial value (5.5V type)
Within ±20% of initial value (11V type, 12Vtype)
ESR
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Appearance
No obvious abnormality
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−25 ℃ →Room temperature→
＋70 ℃ →Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：70±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Super Capacitors Vol.12 29
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.8 FA Series, FE Series
FA Series
Markings on sleeve
Dimensions
2.0 MAX.
H MAX.
ℓMAX.
F D ± 0.5
Rated voltage
Date
code
A1
001
FA
5V
0.1 F
FA
5V
0.1 F
Serial
number
A1
001
FA
5V
0.1 F
FA
5V
0.1 F
Sleeve
Nominal
capacitance
Negative polarity
identification mark
P ± 0.5
○ ○
−
＋
d1 ± 0.1
d2 ± 0.1
（Terminal）
Specifications
Part Number
MAX
operating
voltage
（Vdc）
Rated
voltage
（Vdc）
Charge
system (F)
FA0H473ZF
5.5
5
0.047
0.075
20.0
FA0H104ZF
5.5
5
0.10
0.16
8.0
FA0H224ZF
5.5
5
0.22
0.35
FA0H474ZF
5.5
5
0.47
FA0H105ZF
5.5
5
FA1A223ZF
11.0
FA1A104ZF
FA1A224ZF
FA1A474ZF
Nominal capacitance
MAX
MAX ESR current at
Dimension (unit:mm)
φD
H
P
ℓ
d1
d2
Weight
（g）
0.071
16.0
15.5
5.1
5.0
0.4
1.2
6.2
0.15
21.5
15.5
7.6
5.5
0.6
1.2
12
5.0
0.33
28.5
16.5
10.2
9.5
0.6
1.4
25
0.75
3.5
0.71
36.5
16.5
15.0
9.5
0.6
1.7
42
1.0
1.6
2.5
1.5
44.5
18.5
20.0
9.5
1.0
1.4
65
10
0.022
0.035
20.0
0.066
16.0
25.0
5.1
5.0
0.4
1.2
7.5
11.0
10
0.10
0.16
8.0
0.30
28.5
25.5
10.2
9.5
0.6
1.4
32
11.0
10
0.22
0.35
6.0
0.66
36.5
27.5
15.0
9.5
1.0
1.4
55
11.0
10
0.47
0.75
4.0
1.41
44.5
28.5
20.0
9.5
1.0
1.4
83
FE
5.5 V
Discharge （at 1 kHz） 30 min.
（Ω）
system (F)
（mA）
FE Series
H MAX.
ℓMIN.
F D ± 0.5
Sleeve
0.3 MIN.
Markings on sleeve
Dimensions
Date
code
Serial
number
A1
001
FE
5.5 V
0.047 F
0.047 F
MAX
operating voltage
Nominal
capacitance
A1
P ± 0.5
○ ○
−
＋
Negative polarity
identification mark
d1 ± 0.1
d2 ± 0.1
（Terminal）
Specifications
Part Number
MAX
operating
voltage
（Vdc）
Charge
system (F)
Discharge
system (F)
FE0H473ZF
5.5
0.047
0.075
14.0
0.071
14.5
14.0
5.1
2.2
FE0H104ZF
5.5
0.10
0.16
6.5
0.15
16.5
14.0
5.1
2.7
FE0H224ZF
5.5
0.22
0.35
3.5
0.33
21.5
15.5
7.6
3.0
FE0H474ZF
5.5
0.47
0.75
1.8
0.71
28.5
16.5
10.2
FE0H105ZF
5.5
1.0
1.4
1.0
1.5
36.5
18.5
15.0
FE0H155ZF
5.5
1.5
2.1
0.6
2.3
44.5
18.5
20.0
Nominal capacitance
MAX ESR MAX current
（at 1 kHz） at 30 min.
（Ω）
（mA）
Dimension (unit:mm)
φD
H
P
d2
Weight
（g）
0.4
1.2
3.9
0.4
1.2
5
0.6
1.2
9.5
6.1
0.6
1.4
16
6.1
0.6
1.7
38
6.1
1.0
1.4
72
ℓ
d1
30 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
Specifications
Series name
Item
FA
FE
Test conditions
(conforming to JIS C 5160-1)
Category temperature range
−25 ℃ to ＋70 ℃
−40 ℃ to ＋70 ℃
MAX operating voltage
5.5Vdc, 11Vdc
5.5Vdc
Capacitance
5.5V：0.047F to 1.0F
11V：0.022F to 0.47F
0.047F to 1.5F
Refer to “Measurement Conditions”
Capacitance allowance
＋80 ％, −20 ％
＋80 ％, −20 ％
Refer to “Measurement Conditions”
ESR
Refer to standard ratings
Refer to standard ratings
Measured at 1kHz, 10mA ; See also
“Measurement Conditions”
Refer to standard ratings
Refer to standard ratings
Refer to “Measurement Conditions”
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
Surge voltage：6.3V (5.5V type)
：12.6V (11V type)
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.047F
：0.10F
：0.22F
：0.47F
：1.0F, 1.5F
Discharge resistance：0Ω
Temperature：70±2 ℃
Current (30-minutes value)
Capacitance
ESR
Current (30 minutes value)
Surge
Appearance
Characteristics
in different
temperature
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration
resistance
Temperature
cycle
High temp. and
high humidity
resistance
High
temperature
load
Phase
2
70% or higher than initial value
300% or less than initial value
Phase
3
Phase
5
Phase
6
Phase
2
Phase
3
150% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Phase
5
Phase
6
40% or higher than initial value
400% or less than initial value
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase3：−40±2 ℃ (FE type)
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
No terminal damage
No terminal damage
Conforms to 4.9
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Over 3/4 of the terminal should
be covered by the new solder
Over 3/4 of the terminal should
be covered by the new solder
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
Satisfy initial ratings
Appearance
No obvious abnormality
No obvious abnormality
Capacitance
Over 90% of initial value
Within ±20% of initial value
Not to exceed 120% of initial
ratings
Not to exceed 120% of initial
ratings
Not to exceed 120% of initial
ratings
Not to exceed 120% of initial
ratings
Solderability
Solder heat
resistance
No obvious abnormality
ESR
Current (30 minutes value)
Appearance
No obvious abnormality
No obvious abnormality
Capacitance
Over 85% of initial value
Within ±30% of initial value
ESR
Below 120% of initial ratings
Below 200% of initial ratings
Current (30 minutes value)
Below 200% of initial ratings
Below 200% of initial ratings
Appearance
No obvious abnormality
No obvious abnormality
300Ω
150Ω
56Ω
30Ω
15Ω
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−25℃ (−40℃ for FE type)→
Room temperature→
＋70℃→Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：70±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
Super Capacitors Vol.12 31
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
6.9 HV Series (High capacitance Type)
Dimensions
Markings on sleeve
H
L min.
ΔL min.
2.7V
10F
SuperCapacitor
HV
Positive terminal
ød
øD±0.5
P±0.1
Negative terminal
Specifications
Part Number
MAX
operating
voltage
（Vdc）
HVS0E106NF
HVS0E226NF
HVS0E506NF
HVS0E107NF
2.7
2.7
2.7
2.7
Nominal
MAX ESR MAX current
capacitance （at 1 kHz） at 30 min.
（F）
（Ω）
（mA）
10
22
50
100
100
100
30
30
8
18
40
81
Dimension (unit:mm)
φD
H
P
φd
L
ΔL
Weight
（g）
10.0
12.5
18.0
22.0
35±2
35±2
40±5
50±5
5.0
5.0
7.5
10.2
0.6
0.6
0.8
1.0
15.0
15.0
15.0
15.0
5.0
5.0
5.0
5.0
4.5
6.5
14.0
24.0
Specifications
Item
MAX operating voltage
Capacitance
Capacitance allowance
Specifications
−25 ℃ to ＋60 ℃ (50F, 100F),
−25 ℃ to ＋70 ℃ (10F, 22F),
2.7Vdc
10F, 22F, 50F, 100F
±30 ％
ESR
Refer to standard ratings
Category temperature range
Current (30-minutes value)
Characteristics in
different temperature
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Lead strength (tensile)
Vibration resistance
Capacitance
ESR
Current (30 minutes value)
Appearance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
Satisfy initial ratings
No obvious abnormality
Over 3/4 of the terminal should be covered by
the new solder
Solderability
Solder heat resistance
Refer to standard ratings
50% higher than initial value
Phase 2
400% or less than initial value
150% or less than initial value
Phase 4
Satisfy initial ratings
1.5×10−3CV (A) or below
Within ±20% of initial value
Phase 5
Satisfy initial ratings
Satisfy initial ratings
No terminal damage
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Satisfy initial ratings
No obvious abnormality
Satisfy initial ratings
Appearance
No obvious abnormality
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Within ±20% of initial value
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
No obvious abnormality
Within ±30% of initial value
Below 200% of initial ratings
Below 200% of initial ratings
Appearance
No obvious abnormality
Test conditions (conforming to JIS C 5160-2)
Refer to “Measurement Conditions”
Refer to “Measurement Conditions”
Measured at 1kHz, 10mA ; See also “Measurement
Conditions”
Refer to “Measurement Conditions”
Conforms to 4.13
Phase2：Category MIN temp.
Phase4：Category MAX temp.
Phase5：25 ℃
Conforms to 4.5
Conforms to 4.9
Frequency：10 to 55 Hz
Testing time：6 hours
Conforms to 4.7
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.6
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.8
Temperature condition：−25℃→Room temperature→
＋70℃ (10F, 22F), ＋60℃ (50F, 100F)→
Room temperature
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃ (50F, 100F)
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.10
Temperature：＋70 ℃ (10F, 22F), ＋60 ℃ (50F, 100F)
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000＋480Hours
32 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
7. Packing
1. FM Series
(1) Bulk
Packing method：Pack in vinyl bags then pack them into cardboard boxes.
Standard packing quantity：1000pcs (100pcs / vinyl bag×10)
However：FM0H104ZF-L1 and FM0H224ZF-L1＝800pcs, FMC0H334ZF＝400pcs, FMC0H334ZF-L1＝300pcs
(2) Taping
Packing method：Ammo pack
Standard packing quantity：1000pcs However, FMC0H334ZFTP( ) = 400pcs
2. FC Series
Part name
FC0H473ZFTBR24
FC0H104ZFTBR24
FC0H224ZFTBR24
FC0H474ZFTBR32-SS
FC0H105ZFTBR44-SS
FC0V104ZFTBR24
FC0V224ZFTBR24
FC0V474ZFTBR24
FCS0H473ZFTBR24
FCS0H104ZFTBR24
FCS0H224ZFTBR24
FCS0V104ZFTBR24
FCS0V224ZFTBR24
FCS0V474ZFTBR24
FCH0V683ZFTBR16
FCH0H433ZFTBR16
Packing unit
1000 PCS. / reel
1000 PCS. / reel
500 PCS. / reel
200 PCS. / reel
150 PCS. / reel
1000 PCS. / reel
1000 PCS. / reel
500 PCS. / reel
1000 PCS. / reel
1000 PCS. / reel
500 PCS. / reel
1000 PCS. / reel
1000 PCS. / reel
500 PCS. / reel
1500 PCS. / reel
1500 PCS. / reel
3．FG, FT, FS, FR, FY, FA Series
(1) Bulk (Small type)
Packing method：Pack in vinyl bags then pack them into cardboard boxes.
Standard packing quantity: see chart below.
（Unit：Pises）
Series name
FA
5.5V type 11V type
Capacitance
0.010F
−
−
0.022F
−
240
0.047F
400
−
0.10F
−
−
0.22F
−
−
0.47F
−
−
1.0F
−
−
FE
−
−
400
400
−
−
−
FS
5.5V type 11V type, 12V type
−
−
1000
−
800
−
600
−
400
−
−
−
−
−
FYD
−
1000
1000
800
400
240
−
FY
FYH
−
1600
800
600
500
−
−
FYL
2000
2000
1600
−
−
−
−
FR
FG
FT
−
800
400
400
300
240
−
2000
2000
2000
1600
800
300
240
−
−
−
1000
400
400
−
(2) Bulk (large type)
Packing method: Pin the terminal onto a conductive mat; then pack it into individual cardboard box with insulation material.
Standard packing quantity: see chart below.
（Unit：Pises）
Series name
FA
5.5V type 11V type
Capacitance
0.10F
90
50
0.22F
50
30
0.47F
30
20
1.0F
20
−
1.4F
−
−
1.5F
−
−
2.2F
−
−
3.3F
−
−
4.7F
−
−
5.0F
−
−
5.6F
−
−
FE
−
90
50
30
−
20
−
−
−
−
−
FS
5.5V type 11V type, 12V type
−
−
−
−
90
50
50
50
−
−
−
−
−
−
−
−
−
−
−
20
−
−
FYD
−
−
−
90
90
−
50
−
−
−
−
FY
FYH
−
−
90
50
−
−
−
−
−
−
−
FYL
−
−
−
−
−
−
−
−
−
−
−
FR
FG
FT
−
−
−
90
−
−
−
−
−
−
−
−
−
−
−
−
160
90
−
50
−
−
−
−
−
90
−
−
50
30
−
−
20
4. Winded type (HV Series)
Packing method：Pack in vinyl bags then pack them into cardboard boxes.
Standard packing quantity：320pcs (10F), 224pcs (22F), 120pcs (50F), 80pcs (100F)
Super Capacitors Vol.12 33
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
8. List of Plating Type and Sleeve Type
By changing the solder plating from leaded solder to lead-free solder, and the outer tube material of can-cased conventional
SuperCapacitor from polyvinyl chloride to Polyethylene Terephathatate (PET), our new SuperCapacitor has now became even
more friendlier to the environment.
a. Iron ＋ copper base ＋ lead-free solder plating (Sn-1Cu)
b. SUS nickel base ＋ copper base ＋ reflow lead-free solder plating (100% Sn, reflow processed)
c. Iron ＋ copper base ＋ lead-free solder plating (100% Sn)
Series
FA
FE
FS
FR
FT
FY
FG
FM
FC
HV
Part Number
All FA Series
All FE Series
All FS Series
All FR Series
All FT Series
All FYD type
All FYH type
FYL0H473ZF
FYL0H223ZF
FYL0H103ZF
FG0H103ZF
FG0H223ZF
FG0H473ZF
FG0H104ZF
FG0H224ZF
FG0H474ZF
FG0H105ZF
FG0H225ZF
FG0H475ZF
FGH0H104ZF
FGH0H224ZF
FGH0H474ZF
FGH0H105ZF
All FGR type
All FM Series
FC0H473ZFTBR24
FC0H104ZFTBR24
FC0H224ZFTBR24
FC0H474ZFTBR32-SS
FC0H105ZFTBR44-SS
FC0V104ZFTBR24
FC0V224ZFTBR24
FC0V474ZFTBR24
FCH0V683ZFTBR16
FCH0H433ZFTBR16
FCS0H473ZFTBR24
FCS0H104ZFTBR24
FCS0H224ZFTBR24
FCS0V104ZFTBR24
FCS0V224ZFTBR24
FCS0V474ZFTBR24
All HV Series
Plating
a
a
a
a
a
a
a
a
b
b
b
b
b
b
a
a
a
a
a
b
b
a
a
a
a
b
b
b
a
a
b
b
b
b
b
b
b
b
b
b
b
c
Sleeve
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET (Blue)
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
PET（Blue）
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
No tube used
PET (Blue)
Recommended Pb-free solder : Sn / 3.5Ag / 0.75Cu
Sn / 3.0Ag / 0.5Cu
Sn / 0.7Cu
Sn / 2.5Ag / 1.0Bi / 0.5Cu
34 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
9. Measurement Conditions
(1) Capacitance ( Charge System )
Capacitance is calculated from expression (9) by measuring the charge time constant ( τ ) of the capacitor (C). Prior to
measurement, short between both pins of the capacitor for 30 minutes or more to let it discharge. In addition, follow the indication
of the product when determining the polarity of the capacitor during charging.
Capacitance: C =
τ
RC
(F)
EO: 3.0 (V) … Product with maximum operating voltage
(9)
3.5 V
5.0 (V) … Product with maximum operating voltage
5.5 V
6.0 (V) … Product with maximum operating voltage
Swich
6.5 V
10.0 (V) … Product with maximum operating voltage
RC
EO
C
+
–
11 V
VC
12.0 (V) … Product with maximum operating voltage
12 V
τ: Time from start of charging until Vc becomes
0.632E0 (V) (sec)
RC: See table below (Ω).
FA
FE
FS
0.010F
0.022F
0.033F
0.043F
0.047F
0.068F
0.10F
FY
FR
FYD
FYH
FYL
–
–
–
–
–
5000 Ω
–
1000 Ω
–
1000 Ω 2000 Ω 2000 Ω 2000 Ω 2000 Ω
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1000 Ω 1000 Ω 1000 Ω 2000 Ω 1000 Ω 2000 Ω 1000 Ω
–
–
–
–
–
–
–
510 Ω
510 Ω
510 Ω 1000 Ω 510 Ω
–
1000 Ω
0.22F
200 Ω
200 Ω
200 Ω
510 Ω
510 Ω
–
510 Ω
0.33F
0.47F
1.0F
1.4F
1.5F
2.2F
3.3F
4.7F
5.0F
5.6F
–
100 Ω
51 Ω
–
–
–
–
–
–
–
–
100 Ω
51 Ω
–
51 Ω
–
–
–
–
–
–
100 Ω
100 Ω
–
–
–
–
–
100 Ω
–
–
200 Ω
100 Ω
200 Ω
–
100 Ω
–
–
–
–
–
200 Ω
100 Ω
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
200 Ω
100 Ω
–
–
–
–
–
–
–
FM, FME
FMR, FML
5000 Ω
2000 Ω
Discharge
–
2000 Ω
–
1000 Ω
0H: Discharge
0V: 1000 Ω
–
–
–
–
–
–
–
–
–
–
FG
FGH
FGR
–
5000 Ω
–
–
2000 Ω
–
–
–
–
–
–
–
1000 Ω 2000 Ω
–
–
–
–
1000 Ω 1000 Ω Discharge
FMC
–
FC, FCH
FCS
–
–
Discharge
–
–
–
Discharge
–
–
–
Discharge
–
510 Ω Discharge
FT
1000 Ω Discharge
200 Ω
Discharge
Discharge
–
–
–
1000 Ω Discharge
–
510 Ω Discharge
–
–
–
–
510 Ω
–
–
200 Ω
–
–
–
–
–
100 Ω
–
–
–
–
–
–
–
–
100 Ω
100 Ω
–
–
51 Ω
51 Ω
–
–
20 Ω
–
Discharge
Discharge
–
–
–
–
–
–
–
*Capacitance values according to the constant current discharge method.
Table 3 Capacitance measurement
Capacitance (Discharge System)
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the condensor terminal
reaches 5.5 V.
Then, use a constant current load device and measure the time for the terminal voltage to drop from 3.0 to 2.5 V upon
discharge at 0.22 mA for 0.22 F, for example, and calculate the static capacitance according to the equation shown below.
Note: The current value is 1 mA discharged per 1F.
SW 0.22mA(I)
A
I×(T2−T1)
V1−V2
(F)
5.5V
V
C
R
Voltage
Capactance：C＝
5.5V
V1 : 3.0V
V1
V1 : 2.5V
V2
30 min.
T1
T2
Duration (sec.)
Super Capacitors Vol.12 35
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
10.
Notes on Using Super Capacitor
(Electric Double-Layer Capacitor)
1. Circuitry design
1.1 Useful life
The electrical double layered capacitor (super capacitor) uses electrolyte and is sealed with rubber etc. Water in the
electrolyte can evaporate in use over long periods at high temperatures, thus reducing electrostatic capacity which in turn will
create greater internal resistance. The characteristics of the super capacitor can vary greatly depending on the environment
it is used in. Therefore, controlling the usage environment will ensure prolonged life of the part.
Basic breakdown mode is an open mode due to increased internal resistance.
1.2 Fail rate in the field
Based on field data, the fail rate is calculated at approx. 0.006Fit. We estimate that unreported failures are ten times this
amount. Therefore, we assume that the fail rate is below 0.06Fit.
1.3 Voltage application when maximum usable voltage is exceeded
Performance may be compromised, and in some cases leakage or damage may occur if applied voltage exceeds maximum
working voltage.
1.4 Use of capacitor as a smoothing capacitor (ripple absorption) in electrical circuits
As super capacitors contain a high level of internal resistance, they are not recommended for use as electrical smoothing
capacitors in electrical circuits.
Performance may be compromised, and in some cases leakage or damage may occur if a super capacitor is used in ripple
absorption.
1.5 Series connections
As applied voltage balance to each super capacitor is lost when used in series connection, excess voltage may be applied to
some super capacitors, which will not only negatively affect its performance but may also cause leakage and/or damage.
Allow ample margin for maximum voltage or attach a circuit for applying equal voltage to each super capacitor (partial
pressure resistor/voltage divider) when using super capacitors in series connection.
Also, arrange super capacitors so that the temperature between each capacitor will not vary.
1.6 Outer sleeve insulation
The outer sleeve wrapped around the super capacitor indicates that it is sealed, however the outer sleeve is not guaranteed
for insulation purposes. Therefore, it cannot be used where insulation is necessary.
1.7 Polar characteristics
The super capacitor is manufactured so that the terminal on the outer case is negative (-). Align the (-) symbol during use. Even
though discharging has been carried out prior to shipping, any residual electrical charge may negatively affect other parts.
1.8 Use next to heat emitters
Useful life of the super capacitor will be significantly affected if used near heat emitting items (coils, power transistors, and
posistors etc) where the super capacitor itself may become heated.
1.9 Usage environment
This device cannot be used in any acidic, alkaline or similar type of environment.
36 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
1.10 Super capacitors fitted with pressure valves
HV series super capacitors are fitted with pressure valves Make an opening in the top of the pressure valve to avoid any
damage to the super capacitor when the pressure valve is in use. Allow at least a 2mm opening for models with a diameter
of φ18mm or less, and at least a 3mm opening for models with a diameter of φ22mm.
2. Mounting
2.1 Mounting onto a reflow furnace
Except for the FC series, it is not possible to mount this capacitor onto an IR / VPS reflow furnace. Do not immerse the
capacitor into a soldering dip tank.
2.2 Flow soldering conditions
Keep solder under 260 ℃ and soldering time to within 10 seconds when using the flow automatic soldering method. (Except
for the FC and HV series)
2.3 Installation using a soldering iron
Care must be taken to prevent the soldering iron from touching other parts when soldering. Keep the tip of the soldering iron
under 400 ℃ and soldering time to within 3 seconds. Always make sure that the temperature of the tip is controlled. Internal
capacitor resistance is likely to increase if the terminals are overheated.
2.4 Lead terminal processing
Do not attempt to bend or polish the capacitor terminals with sand paper etc. Soldering may not be possible if the metallic
plating is removed from the top of the terminals.
2.5 Cleaning, Coating, and Potting
Except for the FM series, cleaning, coating, and potting must not be carried out. Consult us if this type of procedure is
necessary.
Terminals should be dried at less than the maximum operating temperature after cleaning.
3. Storage
3.1 Temperature and Humidity
Make sure that the super capacitor is stored according to the following conditions: Temp.: 5〜35 ℃ (Standard 25), Humidity:
20〜70% (Standard: 50%). Do not allow the build up of condensation through sudden temperature change.
3.2 Environment conditions
Make sure that there are no corrosive gasses like sulfur dioxide as penetration of the lead terminals is possible.
Always store this item in an area with low dust and dirt levels.
Make sure that the packaging will not be deformed through heavy loading, movement and/or knocks.
Keep out of direct sunlight, and away from radiation, static electricity, and magnetic fields.
3.3 Maximum storage period
This item may be stored up to one year from the date of delivery if stored at the conditions stated above.
This product should be safe to use even after being stored for over a 1 year period. However, depending on the storage
conditions, we recommend that the soldering is checked.
4. Dismantling
There is a small amount of electrolyte stored within thecapacitor. Do not attempt to dismantle as direct skin contact with the
electrolyte will cause burning.
This product should be treated as industrial waste and not is not to be disposed of by fire.
Super Capacitors Vol.12 37
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
38 Super Capacitors Vol.12
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E
When using our products, the following precautions should
be taken.
(1)
Safety designing of an apparatus or a system allowing for failures of electronic components used
in the system
In general, failures will occur in electronic components at a certain probability. NEC TOKIN
makes every effort to improve the quality and reliability of electronic component products.
However, it is impossible to completely eliminate the probability of failures. Therefore, when
using NEC TOKIN’s electronic component products, systems should be carefully designed to
ensure redundancy in the event of an accident which would result in injury or death, fire, or social
damage, to ensure the prevention of the spread of fire, and the prevention of faulty operation.
(Please refer to pre-cautions to be taken when using SuperCapacitor capacitors for the details of
failures.)
(2)
Quality level of various kinds of parts, and equipment in which the parts can be utilized
Electronic components have a standard quality level unless otherwise specified.
NEC TOKIN classifies the level of quality of electronic component products into three levels, in
order from a lower level, a standard quality level, a special quality level, and a custom quality level
in which a customer individually specifies a quality assurance program. Each of the quality levels
has recommended applications.
If a user wants to use the electronic parts having a standard quality level in applications other than
the applications specified for the standard quality level, they should always consult a member of
our company’s sales staff before using the electronic parts.
Standard quality level:
Computers, office automation equipment, communications equipment,
measuring instruments, AV equipment, household electrical appliances, machine tools, personal equipment, industrial robots
Special quality level:
Transportation equipment (automobiles, railways, shipping, or the
like), traffic signals, disaster prevention/crime prevention systems,
safety devices, and medical equipment which is not directly intended
for life-support purposes
Custom quality level:
Equipment for airplanes, aerospace equipment, nuclear power control
systems, and medical equipment, apparatus or systems for life-support purposes
Unless otherwise shown, the quality level of NEC TOKIN’s electronic component products included
in documents such as catalogues, data sheets or data books is the standard quality level.
(3)
This manual is subject to change without notice.
The contents of this manual are based on data which is correct as of July 2010, and they may be
changed without notice. If our products are used for mass-production design, please cousult with
a member of our company’s sales staff by way of precaution.
(4)
Reprinting and copying of this manual without prior written permission from NEC TOKIN Corporation are not permitted.
(5)
Industrial property problems
In the event any problems associated with industrial property of a third party arising as a result of
the use of our products, NEC TOKIN assumes no responsibility for problems other than problems
directly associated with the constitution and manufacturing method of the products.
(6)
Should any of these products come under the category of strategic goods or services (according
to Japan's foreign trade and foreign exchange regulations), the sender must obtain an export
license from the Japanese Government befor said products can be exported outside Japan.
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2010.11.8 9565SCAVOL12E

Open as PDF

Similar pages