Hirose FH41-28S-0.5SH05 0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded ffc Datasheet

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
FH41 Series
THine Electronics, Inc.
Next-generation chipset (V-by-One®HS*)
Compatible connector
*High-speed serial interface technology
for image transmission
Space saving (68 pos. shown)
2.5mm
38mm
■Features
1.Compatibility with impedance control, shield
FFC
The FH41 series is equipped with a GND exclusive terminal
and available for connection with impedance control, shield
FFC.
2.Differential impedance 100Ω±10%
6.2mm
figure.1
The FH41 series features a terminal design considering
impedance control, and making high speed transmission
possible.
Sig
0.5 nal co
mm nta
pitc ct
h
3.Highly reliable connection, tough structure
The FH41 series follows the structure of the proven FH28
series, and achieves:
- High reliability thanks to the FFC positioning mechanism
- Reliable connection operation and no unlocking thanks to the
durable structure.
4.One-finger operation of the actuator
Proven (in several other Hirose's connectors!) Flip-Lock
rotating actuator assures reliable mechanical and electrical
connection with FPC, confirming it with a definite tactile feel.
5.Board placement with automatic equipment
figure.2
Flat upper surface and tape and reel packaging facilitate
vacuum pick-up and placement.
Standard reel packaging contains 2,500 connectors.
Gro
2.5 und
mm con
pitc tact
h
Signal contact connection area
6.Halogen-free *
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
FFC
figure.3
GND contact connection area
2010.9
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Specifications
Current rating 0.5 A(Note1)
Voltage rating 50 Vrms AC
Ratings
Recommended FPC Thickness
Operating temperature range:
-40 to +85°C (Note 2)
Operating humidity range:
Relative humidity 90% max. (No condensation)
Storage temperature range:
-10 to +50°C (Note 3)
Storage humidity range:
Relative humidity 90% max. (No condensation)
0.3 ±0.05 mm, Gold plated contact pads (GND plate:t=0.5±0.05mm,tin plateing)
Item
Specification
Conditions
1.Insulation
resistance
500 Mø min.
100 V DC
2.Withstanding voltage
No flashover or insulation breakdown
150 Vrms AC / one minute
3.Contact resistance
100 mø max.
* Including FFC conductor resistance
1 mA, AC max (AC: 1kHz)
4.Durability
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
20 cycles
5.Vibration
No electrical discontinuity of 1μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Frequency: 10 to 55 Hz, single amplitude of 0.75mm,
10 cycles in each of the 3 directions
6.Shock
No electrical discontinuity of 1μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Acceleration of 981m/s 6 ms duration, sine halfwave,
3 cycles in each of the 3 axis
7.Humidity
(Steady state)
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
96 hours at 40°C and humidity of 90 to 95%
8.Temperature cycle
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
Temperature : -40°C → +15°C to +35°C → +85°C →
+15°C to +35°C
Time: 30 → 2 to 3 → 30 → 2 to 3 minutes
5 cycles
9.Resistance to
soldering heat
No deformation of components affecting performance
Reflow: At the recommended temperature profile
Manual soldering: 350°C ±5°C for 5 seconds
2
Note 1. When passing the current through all of the contacts, use 70% of the rated current.
Note 2.Includes temperature rise caused by current flow.
Note 3. The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or
during transportation after board mounting.
Note 4. Information contained in this catalog represents general requirements for this Series.
Contact us for the drawings and specifications for a specific part number shown.
■Materials
Part
Material
Insulator
LCP
Contacts
Phosphor bronze
Metal fittings
Brass
Finish
Remarks
Color:Gray
UL94V-0
Color:Black
Gold plated
---------
Pure tin reflow plated
■Ordering information
FH 41 − 50S − 0.5 SH (05)
❶
❷
❸
❶ Series name : FH
❷ Series No.: 41
❸ Number of positions : 28 to 68
❹ Contact pitch : 0.5mm
2
❹
❺
❻
❺ SH : SMT horizontal mounting type
❻ Plating specifications :(05)…Gold plated
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Connector Dimensions
C
D
(5.05)
1
(5.45)
(0.12)
No. of contacts
Cavity No.
2.5
(0.12)
(0.15)
2
2.5
(4.7)
E
0.25
0.8
(Dimension for FFC opening)
6.2
G
Note 1. The coplanarity of each terminal lead within specified dimension is 0.1 mm Max.
2. Packaged on tape and reel only. Check packaging specification.
3. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector.
4. After reflow, the terminal plating may change color, however this does not represent a quality issue.
Unit : mm
Part Number
CL No.
FH41-28S-0.5SH(05)
580-2208-1-05
28
FH41-40S-0.5SH(05)
580-2205-3-05
40
FH41-50S-0.5SH(05)
580-2204-0-05
580-2202-5-05
FH41-68S-0.5SH(05)
Number of contacts No. of Contacts(GND contacts)
C
D
E
F
G
5
18
8
24
13.5
10
14.57
15.95
19.5
17.5
20.57
21.95
50
10
68
13
29
24.5
22.5
25.57
26.95
38
33.5
30
34.57
35.95
Note1.Tape and reel packaging (2,500 pieces/reel).
Order by number of reels.
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Recommended PCB mounting pattern and metal mask dimensions
D±0.05
1.2±0.05(Land pattern)
1±0.05(Metal mask)
6.6±0.1
6.35±0.05
0.65±0.05
1.55±0.05
0.3±0.03 (Land pattern)
0.25±0.03(Metal mask)
0.5±0.05
1±0.05
0.3±0.03(Land pattern)
0.2±0.0(Metal mask)
2.5±0.05
0.4±0.03
E±0.05
H±0.05
Recommended metal mask thickness t=0.1
■Recommended FFC Dimensions
0.5±0.1
5.5MIN
2.7±0.5
.2
0.5±0.05
0.3±0.05
0.1MIN
5.5MIN
17.7MAX
R0
0.5±0.05
0.3±0.03
1.9±0.1
2.6±0.1
3.8±0.1
2-
2.2±0.5
0.2
2-R
J±0.1
K±0.07
D±0.05
0.2m
ax
1
Shield area
2-R
2-R
0.2
ma
x
Ground plate
Note 1
Please overlap shield plate on ground plate.
Unit : mm
Part Number
CL No.
FH41-28S-0.5SH(05)
580-2208-1-05
Number of contacts No. of Contacts(GND contacts)
28
FH41-40S-0.5SH(05)
580-2205-3-05
FH41-50S-0.5SH(05)
580-2204-0-05
FH41-68S-0.5SH(05)
580-2202-5-05
Note1.Tape and reel packaging (2,500 pieces/reel).
Order by number of reels.
4
H
J
K
5
16
15.7
14.5
40
8
22
21.7
20.5
50
10
27
26.7
25.5
68
13
36
35.7
34.5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Recommended FFC construction
Material Name
Material
thickness(μm) thickness(μm)
Shielding Material
Conouctiye Adhesive
Polyester Type
Copper Film (Tin Plated)
1
Adhesive
Acrylic Type
24
1
Base Material
Polyester Type
12
1
Adhesive
Acrylic Type
24
1
Insulated Layer
Polyester Type
25
Adhesive
Polyester Type
35
Soft Copper Film
(Nickel Under Plated / Gold Plated)
35
35
Adhesive
Polyester Type
35
35
Insulated Layer
Polyester Type
25
25
Adhesive
Polyester Type
30
30
Siiffener
Polyester Type
188
188
503
313
Total
Note 1
70
Please overlap shield plate on ground plate.
5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Packaging Specification
●Embossed Carrier Tape Dimensions
1.75±0.1
N±0.1
M±0.1
L±0.3
0
0 .1
11
4±0.1 2±0.1 12±0.1
(P)
(Q)
(R)
L±0.3
N±0.1
(2.9)
(0.3)
.5 +
1.75±0.1
.5 +
11
4±0.1 2±0.1 12±0.1
(P)
(Q)
(R)
(2.9)
(0.3)
(Tape width of 32mm min.)
0
0 .1
(Tape width of 24mm max.)
(1.64:Vacum pick up area)
(5.75)
(7.35)
C
L
(1.64:Vacum pick up area)
(5.75)
(7.35)
Direction of unreeling
C
L
Direction of unreeling
(Ø1
3)
●Reel Dimensions
(Ø80)
(Ø380)
(S:Outside)
(T:Inside)
Trailer
Portion equipped with connectors
Leader (400mm min)
Embossed carrier tape
14 Empty component compartments min
Top cover tape
10 Empty component compartments min
6
Unit : mm
Part Number
CL No.
FH41-28S-0.5SH(05)
580-2208-1-05
Number of contacts No. of Contacts(GND contacts)
28
5
L
32
M
N
P
28.4 14.2 18.3
Q
17
R
S
T
15.7 37.4 33.4
FH41-40S-0.5SH(05)
580-2205-3-05
40
8
44
40.4 20.2 24.3
23
21.7 49.4 45.4
FH41-50S-0.5SH(05)
580-2204-0-05
50
10
44
40.4 20.2 29.3
28
26.7 49.4 45.4
FH41-68S-0.5SH(05)
580-2202-5-05
68
13
56
52.4 26.2 38.3
37
35.7 61.4 57.4
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Temperature Profile
MAX 250℃
Temperature (ç)
250
230℃
200
HRS test condition
Solder method
Environment
Solder composition
200℃
150
Test board
Land dimensions
Metal mask
150℃
:Reflow, IR/hot air
:Room air
:Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s Part
Number:M705-221CM5-32-10.5)
:Glass epoxy 30mm×60mm×0.8mm thick
:0.3mm×0.65mm, 0.3mm×1.2mm
:0.25×0.65, 0.2×0.1mm thick
The temperature profiles shown are based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume / thickness and board size /
thickness. Consult your solder paste and equipment manufacturer for
specific recommendations.
100
50
25℃
(60sec.)
0
90~120sec.
Preheating
(60sec.)
soldering
Start
Time(Seconds)
7
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Operation and Precautions
Operation
1.FFC insertion procedure.
Connector installed on the board.
Precautions
❶ Do not force the actuator to open beyond its fully open
position. Do not use any type of tool to open the actuator.
❶ Lift up the actuator. Use thumb or index finger
110°
❷ Fully insert the FFC in the connector parallel to
mounting surface, with the exposed conductive traces
facing down.
❷ Do not forcefully bend the FFC upward. Consult FFC
manufacturer for the
recommended bend radiuses.
❸ Rotate down the actuator until firmly closed. It is
critical that the inserted FFC is not moved and remains
fully inserted.
❸ For connectors with multiple contacts, such as 80 pos.
rotate down the actuator pushing at both ends.
2.FFC removal
❹ Load to FFC
Be very careful not to apply any force to the connector
directly after inserting FFC.
Otherwise, the connector may become unlocked or
the FFC may break.
In particular, design the FFC layout with care not to
bend it sharply upward in a vertial direction near the
insertion opening.
Fix the FFC when loads are applied to it continuously.
Fully open the actuator.
Carefully withdraw the FFC exercising caution not to
deform or damage it.
8
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Precautions (mating/un-mating FFC with the retention tabs)
Precautions
Operation
1.How to insert
Insert the cable into the interspace between the mold walls
) at both ends of entrance where the connector is
(
inserted and the guide walls (
) at both ends of
interior connector so the cable tabs are properly located.
❷ Avoid “ride on”
Avoid insertion so the cables ride on any guide. Be
sure NOT to close the actuator as the cables ride on
any guide. It may cause conduction failure.
Ride on a left guide
Ride on a right guide
Correct insertion
2.Precautions when mating /un-mating
❶ Avoid insertion in diagonal direction.
Do not insert the cable in diagonal direction.
A part of the connector may touches the contacts
resulting in deformation of the contacts.
Insert the cable straight into the connector and hook
the cable tabs with the guide.
After insertion, slightly pull the cables to make sure
the cable tabs are firmly secured. No removal of the
cable means correct insertion.
① Insert the cable straight
and obliquely from
above.
Do not close the actuator as the cables ride on.
In the event it is locked as the cables ride on a guide,
absolutely avoid moving the cable. In this case, open
the actuator and re-insert the cable as instructed in “
1.How to insert”
Do not move the cables back and forth and around as
the cables ride on the guide when the actuator is closed.
② Slightly pull the cable
to make sure the tabs
are firmly secured.
③ Close the actuator.
9
Similar pages