FAIRCHILD FMS6145MTC14

FMS6145
Low-Cost Five-Channel 4th-Order
Standard Definition Video Filter Driver
Features
Description
■ Five 4th-order 8MHz (SD) filters
The FMS6145 Low-Cost Video Filter (LCVF) is intended
to replace passive LC filters and drivers with a low-cost
integrated device. Five 4th-order filters provide improved
image quality compared to typical 2nd or 3rd-order
passive solutions.
■ Drives single, AC- or DC-coupled, video loads (2Vpp, 150Ω)
■ Drives dual, AC- or DC-coupled, video loads (2Vpp, 75Ω)
■ Transparent input clamping
■ AC- or DC-coupled inputs
■ AC- or DC-coupled outputs
■ DC-coupled outputs eliminate AC-coupling capacitors
■ 5V only
■ Robust 8kV ESD protection
■ Lead-free TSSOP-14 package
The FMS6145 may be directly driven by a DC-coupled
DAC output or an AC-coupled signal. Internal diode
clamps and bias circuitry may be used if AC-coupled
inputs are required (see Applications section for details).
The outputs can drive AC- or DC-coupled single (150Ω) or
dual (75Ω) loads. DC coupling the outputs removes the
need for output coupling capacitors. The input DC levels
are offset approximately +280mV at the output (see
Applications section for details).
Applications
■ Cable set-top boxes
■ Satellite set-top boxes
■ DVD players
■ HDTV
■ Personal Video Recorders (PVR)
■ Video On Demand (VOD)
Functional Block Diagram
IN1
Transparent Clamp
6dB
OUT1
IN2
Transparent Clamp
6dB
OUT2
IN3
Transparent Clamp
6dB
OUT3
IN4
Transparent Clamp
6dB
OUT4
IN5
Transparent Clamp
6dB
OUT5
8MHz, 4th order
Ordering Information
Part Number
FMS6145MTC14
FMS6145MTC14X
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
Package
Pb-Free
Operating
Temperture Range
Packaging
Method
TSSOP-14
TSSOP-14
Yes
Yes
-40°C to +85°C
-40°C to +85°C
Tube
Tape and Reel
www.fairchildsemi.com
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
December 2006
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
Pin Configuration
IN1
1
IN2
2
IN3
3
VCC
14
OUT1
13
OUT2
12
OUT3
4
11
GND
IN4
5
10
OUT4
IN5
6
9
OUT5
NC
7
8
NC
FMS6145
14-pin
TSSOP
Pin Assignments
Pin #
Name
Type
Description
1
IN1
Input
Video input, channel 1
2
IN2
Input
Video input, channel 2
3
IN3
Input
Video input, channel 3
4
VCC
Input
+5V supply, do not float
5
IN4
Input
Video input, channel 4
6
IN5
Input
Video input, channel 5
7, 8
NC
9
OUT5
Output
Filtered video output, channel 5
10
OUT4
Output
Filtered video output, channel 4
11
GND
Output
Must be tied to ground, do not float
12
OUT3
Output
Filtered video output, channel 3
13
OUT2
Output
Filtered video output, channel 2
14
OUT1
Output
Filtered video output, channel 1
No Connect
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
2
The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The
device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are
not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table defines the conditions
for actual device operation. Functional operation under any of these conditions is NOT implied. Performance and reliability are guaranteed only if recommended operating conditions are not exceeded.
Min.
Max.
Unit
DC Supply Voltage
Parameter
-0.3
6
V
Analog and Digital I/O
-0.3
VCC + 0.3
V
50
mA
Output Channel - Any One Channel (Do Not Exceed)
Reliability Information
Symbol
TJ
TSTSG
Parameter
Min.
Typ.
Junction Temperature
Storage Temperature Range
-65
TL
Lead Temperature (Soldering, 10s)
θJA
Thermal Resistance, JEDEC Standard Multi-layer
Test Boards, Still Air
Max.
Unit
150
°C
+150
°C
300
°C
90
°C/W
Recommended Operating Conditions
Symbol
TA
VCC
Parameter
Min.
Operating Temperature Range
-40
VCC Range
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
Typ.
+4.75
+5.0
Max.
Unit
+85
°C
+5.25
V
www.fairchildsemi.com
3
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
Absolute Maximum Ratings
TA = 25°C, VCC = 5V, RSOURCE = 37.5Ω; all inputs are AC-coupled with 0.1μF; all outputs are AC coupled with 220μF into
150Ω loads; unless otherwise noted.
Symbol
Parameter
Conditions
ICC
Supply Current
VIN
PSRR
Min. Typ. Max. Units
FMS6145 (No Load)
30
Video Input Voltage Range
Referenced to GND if DC-coupled
1.4
Vpp
Power Supply Rejection
DC (All Channels)
-50
dB
(1)
46
mA
Notes:
1.100% tested at 25°C.
AC Electrical Characteristics
TA = 25°C, VIN = 1Vpp, VCC = 5V, RSOURCE = 37.5Ω; all inputs are AC coupled with 0.1μF; all outputs are
AC-coupled with 220μF into 150Ω loads; unless otherwise noted.
Symbol
Parameter
Conditions
AV
Channel Gain
f1dB
-1dB Bandwidth
fc
-3dB Bandwidth
fSB
Attenuation (Stopband Reject)
(1)
(1)
Min. Typ. Max. Units
All Channels
5.6
6.0
6.6
dB
All Channels
4.5
6.7
MHz
All Channels
7.9
MHz
All Channels at f = 27MHz
48
dB
dG
Differential Gain
All Channels
0.3
%
dφ
Differential Phase
All Channels
0.6
°
THD
Output Distortion (All Channels)
VOUT = 1.8Vpp, 1MHz
0.4
%
XTALK
Crosstalk (Channel-to-Channel)
at 1MHz
-60
dB
SNR
Signal-to-Noise Ratio
75
dB
59
ns
tpd
Propagation Delay
All Channels, NTC-7 Weighting:
100kHz to 4.2MHz
Delay from Input-to-Output, 4.5MHz
Notes:
1.100% tested at 25°C.
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
4
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
DC Electrical Characteristics
5
0
-5
-10
-15
-20
-25
-30
-35
-40
-45
-50
-55
50
2
40
30
1
20
Delay (ns)
Normalized Gain (dB)
TA = 25°C, VCC = 5V, RSOURCE = 37.5Ω; all inputs AC coupled with 0.1μF; all outputs are AC coupled with 220μF into 150Ω
loads; unless otherwise noted.
Mkr Frequency
Gain
Ref 400kHz
1 6.68MHz
2 7.87MHz
6dB
-1dB BW
-3dB BW
3
27MHz
400kHz
10
0
-10
-20
-30
-40
-48.66dB
5
1
10
3
20
15
25
1 = 8.2MHz (14.78ns)
-50
30
400kHz
5
10
Frequency (MHz)
Figure 1. Frequency Response
20
25
30
Figure 2. Group Delay vs. Frequency
0.2
-70
0.1
Differential Gain (%)
-60
-80
Noise (dB)
15
Frequency (MHz)
-90
-100
-110
-120
0
-0.1
-0.2
-0.3
-0.4
-130
NTSC
Min = -0.31
Max = 0.03
ppMax = 0.34
-0.5
400kHz
1
2
4
3
5
6
1st
2nd
3rd
4th
5th
6th
Frequency (MHz)
Figure 3. Noise vs. Frequency
Differential Phase (deg)
1.0
0.8
Figure 4. Differential Gain
NTSC
0.6
0.4
0.2
0
-0.2
Min = 0.00
Max = 0.63
ppMax = 0.63
-0.4
1st
2nd
3rd
4th
5th
6th
Figure 5. Differential Phase
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
5
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
Typical Performance Characteristics
The following circuit may be used for direct DC-coupled drive by DACs with an output voltage range of 0V to 1.4V.
AC-coupled or DC-coupled outputs may be used with AC-coupled outputs, offering slightly lower power dissipation.
DVD Player or STB
+5V
0.1
μF
1.0
μF
1
ROUT
IN1
75Ω
220μF
14
220μF
13
75Ω
220μF
12
75Ω
75Ω Video Cables
R
OUT1
75Ω
2
FMS6145
14L TSSOP
3
BOUT
G
OUT2
IN2
GOUT
IN3
75Ω
B
OUT3
75Ω
Video
SoC
4
11
GND
VCC
5
YOUT
IN4
75Ω
220μF
10
220μF
9
75Ω
75Ω Video Cables
Y
OUT4
75Ω
6
IN5
COUT
C
OUT5
75Ω
7
8
NC
NC
DAC load resistors
AC coupling caps
per SoC specifications.
are optional.
Figure 6. Typical Application Diagram
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
6
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
Typical Application Diagrams
75Ω
Application Circuits
The FMS6145 Low Cost Video Filter (LCVF) provides
6dB gain from input to output. In addition, the input is
slightly offset to optimize the output driver performance.
The offset is held to the minimum required value to
decrease the standing DC-current into the load. Typical
voltage levels are shown in the diagram below:
Video Cables
LOAD2
(optional)
75Ω
0.65V
YIN
Driver
LOAD1
YOUT
75Ω
Video Cables
75Ω
Figure 8. Input Clamp Circuit
1.0 -> 1.02V
I/O Configurations
0.65 -> 0.67V
For a DC-coupled DAC drive with DC-coupled outputs,
use the configuration in Figure 9.
0.3 -> 0.32V
0.0 -> 0.02V
VIN
0V - 1.4V
2.28V
1.58V
0.88V
0.28V
VOUT
DVD or
STB
SoC
DAC
Output
Driven by:
DC-Coupled DAC Outputs
AC-Coupled and Clamped
Y, CV, R, G, B
LCVF
Clamp
Inactive
75Ω
There is a 280mV offset from the DC input level to the
DC output level. VOUT = 2 * VIN + 280mV.
Figure 9. DC-Coupled Inputs and Outputs
Alternatively, if the DAC’s average DC output level causes
the signal to exceed the range of 0V to 1.4V, it can be AC
coupled as shown in FIgure 10.
0.85V
0.5V
0.15V
VIN
1.98V
0V - 1.4V
DVD or
STB
SoC
DAC
Output
Driven by:
AC-Coupled and Biased
U, V, Pb, Pr, C
1.28V
0.58V
0.1μ
LCVF
Clamp
Active
75Ω
VOUT
Figure 7. Typical Voltage Levels
Figure 10. AC-Coupled Inputs,
DC-Coupled Outputs
The FMS6145 provides an internal diode clamp to support AC-coupled input signals. If the input signal does not
go below ground, the input clamp does not operate. This
allows DAC outputs to directly drive the FMS6145 without
an AC coupling capacitor. When the input is AC coupled,
the diode clamp sets the sync tip (or lowest voltage) just
below ground. The worst-case sync tip compression due
to the clamp cannot exceed 7mV. The input level set by
the clamp, combined with the internal DC offset, keeps
the output within its acceptable range.
When the FMS6145 is driven by an unknown external
source or a SCART switch with its own clamping circuitry,
the inputs should be AC coupled as shown in Figure 11.
0V - 1.4V
0.1μ
External video
source must
be AC coupled
For symmetric signals like Chroma, U, V, Pb, and Pr, the
average DC bias is fairly constant and the inputs can be
AC coupled with the addition of a pull-up resistor to set
the DC input voltage. DAC outputs can also drive these
same signals without the AC coupling capacitor. A conceptual
illustration of the input clamp circuit is shown in Figure 8.
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
LCVF
Clamp
Active
75Ω
75Ω
Figure 11. SCART with DC-Coupled Outputs
www.fairchildsemi.com
7
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
Application Information
External video
source must
be AC coupled
0V - 1.4V
0.1μ
LCVF
Clamp
Active
75Ω
220μ
75Ω
External video
source must
be AC coupled
75Ω
7.5MΩ
0.1μ
LCVF
Bias
Input
75Ω
Figure 15. Biased SCART with
AC-Coupled Outputs
500mV +/-350mV
Note: The video tilt or line time distortion is dominated by
the AC-coupling capacitor. The value may need to be increased beyond 220μF to obtain satisfactory operation in
some applications.
Figure 12. Biased SCART with
DC-Coupled Outputs
Power Dissipation
The FMS6145 output drive configuration must be considered
when calculating overall power dissipation. Care must be
taken not to exceed the maximum die junction temperature.
The following example can be used to calculate the
FMS6146’s power dissipation and internal temperature rise.
The same circuits can be used with AC-coupled outputs if
desired.
0V - 1.4V
DVD or
STB
SoC
DAC
Output
0.1μ
LCVF
Clamp
Active
75Ω
220μ
Tj = TA + Pd • qJA
EQ. 1
where: Pd = PCH1 + PCH2 + PCH3 and
EQ. 2
PCHx = VCC • ICH - (VO /RL)
EQ. 3
where: VO = 2VIN + 0.280V
EQ. 4
ICH = (ICC/3) + (VO/RL)
EQ. 5
2
VIN = RMS value of input signal
Figure 13. DC-Coupled Inputs,
AC-Coupled Outputs
ICC = 30mA
VCC = 5V
0V - 1.4V
DVD or
STB
SoC
DAC
Output
0.1μ
RL = channel load resistance
LCVF
Clamp
Active
75Ω
220μ
Board layout can also affect thermal characteristics. Refer
to the Layout Considerations section for details.
The FMS6145 is specified to operate with output currents
typically less than 50mA, more than sufficient for a dual
(75Ω) video load. Internal amplifiers are current limited to a
maximum of 100mA and should withstand brief-duration
short-circuit conditions; this capability is not guaranteed.
Figure 14. AC-Coupled Inputs and Outputs
Layout Considerations
■ Include 1μF and 0.1μF ceramic bypass capacitors.
General layout and supply bypassing play major roles in
high-frequency performance and thermal characteristics.
Fairchild offers a demonstration board, FMS6145DEMO,
to guide layout and aid device testing and characterization. The FMS6145DEMO is a four-layer board with full
power and ground planes. Following this layout configuration provides the optimum performance and thermal
characteristics. For optimum results, follow the guidelines
below as a basis for high-frequency layout:
■ Place the 1μF capacitor within 0.75 inches of the
power pin.
■ Place the 0.1μF capacitor within 0.1 inches of the
power pin.
■ For multi-layer boards, use a large ground plane to help
dissipate heat.
■ For two-layer boards, use a ground plane that extends
beyond the device by at least 0.5 inches.
■ Minimize all trace lengths to reduce series inductances.
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
8
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
The same method can be used for biased signals, with the
addition of a pull-up resistor to make sure the clamp never
operates. The internal pull-down resistance is 800kΩ
±20%, so the external resistance should be 7.5MΩ to set
the DC level to 500mV; as shown in Figure 12.
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
Mechanical Dimensions
Dimensions are in millimeters unless otherwise noted.
Figure 16. TSSOP-14 Package
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
9
FMS6145 Low-Cost Five-Channel 4th-Order Standard Definition Video Filter Driver
© 2006 Fairchild Semiconductor Corporation
FMS6145 Rev. 2.0.4
www.fairchildsemi.com
10