Fairchild FPF1005 Intellimaxtm advanced load management product Datasheet

FPF1005-FPF1006
IntelliMAXTM Advanced Load Management Products
tm
Features
General Description
„ 1.2 to 5.5V Input Voltage Range
The FPF1005 & FPF1006 are low RDS P-Channel MOSFET
load switches with CMOS controlled turn-on targeting small
package load switch applications. The input voltage range
operates from 1.2V to 5.5V. Switch control is by a logic
input (ON) capable of interfacing directly with low voltage
control signals. Optional on-chip load resistor is added for
output quick discharge when switch is turned off.
„ Typical RDS(ON) = 50mΩ @ VIN = 5.5V
„ Typical RDS(ON) = 55mΩ @ VIN = 3.3V
„ ESD Protected, above 2000V HBM
Applications
„ PDAs
Both FPF1005 & FPF1006 are available in a small 2X2 MLP- 6
pin plastic package.
„ Cell Phones
„ GPS Devices
„ MP3 Players
„ Digital Cameras
„ Peripheral Ports
„ Hot Swap Supplies
PIN 1
TOP
BOTTOM
Typical Application Circuit
TO LOAD
VOUT
VIN
FPF1005/6
OFF ON
ON
-
COUT
GND
CIN
Ordering Information
Part
Switch
Input Buffer
FPF1005
55mΩ, PMOS
FPF1006
55mΩ, PMOS
©2006 Fairchild Semiconductor Corporation
FPF1005-FPF1006 Rev. D
Output Discharge
ON Pin Activity
Schmitt
NA
Active HI
Schmitt
120Ω
Active HI
1
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
September 2006
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Functional Block Diagram
VIN
Turn-On Slew Rate
Controlled Driver
CONTROL
LOGIC
ON
ESD protection
VOUT
FPF1005/6
Output Discharge
(Optional)
GND
Pin Configuration
GND 6
1 ON
VOUT 5
2 VIN
VOUT 4
3 VIN
MLP 2x2 6L BOTTOM VIEW
Pin Description
Pin
Name
4, 5
VOUT
2, 3
VIN
6
GND
1
ON
FPF1005-FPF1006 Rev. D
Function
Switch Output: Output of the power switch
Supply Input: Input to the power switch and the supply voltage for the IC
Ground
ON/OFF Control Input
2
www.fairchildsemi.com
Parameter
Min.
VIN, VOUT, ON to GND
-0.3
Maximum Continuous Switch Current
Power Dissipation @ TA = 25°C (Note 1)
Storage Junction Temperature
-65
Operating Temperature Range
-40
Thermal Resistance, Junction to Ambient
Electrostatic Discharge Protection
Max.
Unit
6
V
1.5
A
1.2
W
150
°C
85
°C
86
°C/W
HBM
2000
V
MM
200
V
Recommended Operating Range
Parameter
Min.
Max.
Unit
VIN
1.2
5.5
V
Ambient Operating Temperature, TA
-40
85
°C
Electrical Characteristics
VIN = 1.2 to 5.5V, TA = -40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3V and TA = 25°C.
Parameter
Conditions
Symbol
Min.
Typ.
Max.
Unit
Basic Operation
Operating Voltage
VIN
5.5
V
Quiescent Current
IQ
IOUT = 0mA, VIN = VON
1
uA
Off Supply Current
IQ(off)
VON = GND, OUT = open
1
uA
Off Switch Current
ISD(off)
VON = GND, VOUT= 0V
1
uA
On-Resistance
Output Pull Down Resistance
ON Input Logic Low Voltage
ON Input Logic High Voltage
RON
RPD
VIL
VIH
1.2
VIN = 5.5V, TA = 25°C
50
70
VIN = 3.3V, TA = 25°C
55
80
VIN = 1.5V, TA = 25°C
95
135
VIN = 1.2V, TA = 25°C
165
250
VIN = 3.3V, VON = 0V, TA = 25°C, FPF1006
75
1.25
VIN = 4.5V
1.10
VIN = 1.5V
0.50
VIN = 5.5V
2.00
VIN = 4.5V
1.75
VIN = 1.5V
0.75
VON = VIN or GND
ON Input Leakage
120
VIN = 5.5V
mΩ
Ω
V
V
-1
1
uA
Dynamic
Turn on delay
Turn off delay
VOUT Rise Time
VOUT Fall Time
tON
tOFF
tR
tF
VIN = 3.3V, RL=500Ω, CL=0.1uF, TA = 25°C
10
us
VIN = 3.3V, RL=500Ω, CL=0.1uF,
TA = 25°C, FPF1005
50
us
VIN = 3.3V, RL=500Ω, CL=0.1uF,
TA = 25°C, FPF1006
10
us
VIN = 3.3V, RL=500Ω, CL=0.1uF, TA = 25°C
10
us
VIN = 3.3V, RL=500Ω, CL=0.1uF,
TA = 25°C, FPF1005
100
us
VIN = 3.3V, RL=500Ω, CL=0.1uF,
TA = 25°C, FPF1006
10
us
Note 1: Package power dissipation on 1square inch pad, 2 oz. copper board
FPF1005-FPF1006 Rev. D
3
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Absolute Maximum Ratings
2.5
8
2.0
ON THRESHOLD (V)
SUPPLY CURRENT (nA)
10
6
VON = VIN
4
MAX LIMIT
1.5
TYPICAL
1.0
0.5
2
VON = 0V
0.0
0
1
2
3
4
5
6
7
SUPPLY VOLTAGE (V)
8
9
1
10
Figure 1. Quiescent Current vs.VIN
2
3
4
SUPPLY VOLTAGE (V)
5
6
Figure 2. ON Threshold vs. VIN
10
16
SUPPLY CURRENT (nA)
SUPPLY CURRENT (nA)
14
12
10
8
VIN = 5.5V
6
4
8
6
VIN = 5.5V
4
2
2
VIN = 3.3V
VIN = 3.3V
0
0
-40
-15
10
35
60
o
TJ, JUNCTION TEMPERATURE ( C)
-40
85
Figure 3. Quiescent Current vs. Temperature
10
35
60
o
TJ, JUNCTION TEMPERATURE ( C)
85
Figure 4. Quiescent Current (off) vs. Temperature
800
100
90
700
VIN = 5.5V
600
SUPPLY CURRENT (nA)
SUPPLY CURRENT (nA)
-15
500
400
300
200
80
70
60
50
40
30
20
100
VIN = 3.3V
10
0
0
-50
-25
0
25
50
75
o
TJ, JUNCTION TEMPERATURE ( C)
100
1
Figure 5. ISWITCH-OFF Current vs. Temperature
FPF1005-FPF1006 Rev. D
2
3
4
SUPPLY VOLTAGE (V)
5
6
Figure 6. ISWITCH-OFF Current vs. VIN
4
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Typical Characteristics
1.5
400
IOUT = 1A
VIN = 3.3V
IOUT = 1A
1.3
300
RON NORMALIZED
ON RESISTANCE (mOhms)
350
250
200
150
1.1
0.9
100
0.7
50
0
0.5
0
1
2
3
4
5
SUPPLY VOLTAGE (V)
6
7
-50
-25
Figure 7. RON vs. VIN
0
25
50
75
TJ, JUNCTION TEMPERATURE (oC)
100
Figure 8. RON vs. Temperature
1000
100
VIN = 3.3V
RL = 500Ω
CL = 0.1uF
RISE / FALL TIME (uS)
TURN ON/OFF TIME (uS)
VIN = 3.3V
RL = 500Ω
CL = 0.1uF
FPF1005 TOFF
FPF1006 TOFF
FPF1005 TFALL
100
TRISE
10
TON
FPF1006 TFALL
10
1
-50
-25
0
25
50
75
o
TJ, JUNCTION TEMPERATURE ( C)
-50
100
Figure 9. TON/TOff vs. Temperature
VON
2V/DIV
0
25
50
75
TJ, JUNCTION TEMPERATURE (oC)
100
Figure 10. TRISE/TFALL vs. Temperature
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=500Ω
VON
2V/DIV
IOUT
10mA/DIV
IOUT
10mA/DIV
VOUT
2V/DIV
VOUT
2V/DIV
50us/DIV
Figure 11. FPF1005 TON Response
FPF1005-FPF1006 Rev.D
-25
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=500Ω
50us/DIV
Figure 12. FPF1005 TOFF Response
5
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Typical Characteristics
VON
2V/DIV
VON
2V/DIV
IOUT
200mA/DIV
IOUT
200mA/DIV
VOUT
2V/DIV
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=10Ω
VOUT
2V/DIV
5us/DIV
Figure 14. FPF1005 TOFF Response
50us/DIV
Figure 13. FPF1005 TON Response
VON
2V/DIV
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=500Ω
VON
2V/DIV
IOUT
10mA/DIV
VOUT
2V/DIV
50us/DIV
Figure 15. FPF1006 TON Response
50us/DIV
Figure 16. FPF1006 TOFF Response
VON
2V/DIV
VON
2V/DIV
IOUT
200mA/DIV
IOUT
200mA/DIV
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=10Ω
VOUT
2V/DIV
50us/DIV
Figure 17. FPF1006 TON Response
FPF1005-FPF1006 Rev.D
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=500Ω
IOUT
10mA/DIV
VOUT
2V/DIV
VOUT
2V/DIV
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=10Ω
VIN=3.3V
CIN=1uF
COUT=0.1uF
RLOAD=10Ω
5us/DIV
Figure 18. FPF1006 TOFF Response
6
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Typical Characteristics
The FPF1005 & FPF1006 are low RDS(ON) P-Channel load
switches with controlled turn-on. The core of each device is a
55mΩ P-Channel MOSFET and a controller capable of
functioning over a wide input operating range of 1.2-5.5V. The
ON pin, an active HI TTL compatible input, controls the state of
the switch. The FPF1006 contains a 120Ω on-chip load resistor
for quick output discharge when the switch is turned off.
However, VOUT pin of FPF1006 should not be connected
directly to the battery source due to the discharge mechanism of
the load switch.
Application Information
Typical Application
VOUT
VIN
FPF1005/6
CIN
VIN = 3.3V
OFF ON
ON
-
RL
COUT
GND
VON = 3.3V
Input Capacitor
To limit the voltage drop on the input supply caused by transient
in-rush currents when the switch turns-on into a discharged load
capacitor or short-circuit, a capacitor needs to be placed
between VIN and GND. A 1uF ceramic capacitor, CIN, placed
close to the pins is usually sufficient. Higher values of CIN can
be used to further reduce the voltage drop during higher current
application.
Output Capacitor
A 0.1uF capacitor, COUT, should be placed between VOUT and
GND. This capacitor will prevent parasitic board inductance
from forcing VOUT below GND when the switch turns-off. Due to
the integral body diode in the PMOS switch, a CIN greater than
COUT is highly recommended. A COUT greater than CIN can
cause VOUT to exceed VIN when the system supply is removed.
This could result in current flow through the body diode from
VOUT to VIN.
Board Layout
For best performance, all traces should be as short as possible.
To be most effective, the input and output capacitors should be
placed close to the device to minimize the effects that parasitic
trace inductances may have on normal and short-circuit
operation. Using wide traces or large copper planes for all pins
(VIN, VOUT, ON and GND) will help minimize the parasitic
electrical effects along with minimizing the case to ambient
thermal impedance.
FPF1005-FPF1006 Rev.D
7
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Description of Operation
FPF1005/6 Demo board has the components and circuitry to demonstrate the load switch functions. Thermal performance of the load
switch can be improved significantly by connecting the middle pad (pin 7) to the GND area of the PCB.
Figure 19. Demo board silk screen top
and component assembly drawing.
Figure 20. Demo board top layer view.
Figure 21. Demo board bottom layer view.
Dimensional Outline and Pad Layout
NOTES:
A. NON-CONFORMS TO JEDEC REGISTRATION.
B. DIMENSIONS ARE IN MILLIMETERS.
C. DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994
FPF1005-FPF1006 Rev.D
8
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
Evaluation Board Layout
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not
intended to be an exhaustive list of all such trademarks.
FACT Quiet Series™
GlobalOptoisolator™
GTO™
HiSeC™
I2C™
i-Lo™
ImpliedDisconnect™
IntelliMAX™
ISOPLANAR™
LittleFET™
MICROCOUPLER™
MicroFET™
MicroPak™
MICROWIRE™
MSX™
MSXPro™
Across the board. Around the world.™
The Power Franchise®
Programmable Active Droop™
ACEx™
ActiveArray™
Bottomless™
Build it Now™
CoolFET™
CROSSVOLT™
DOME™
EcoSPARK™
E2CMOS™
EnSigna™
FACT™
FAST®
FASTr™
FPS™
FRFET™
OCX™
OCXPro™
OPTOLOGIC®
OPTOPLANAR™
PACMAN™
POP™
Power247™
PowerEdge™
PowerSaver™
PowerTrench®
QFET®
QS™
QT Optoelectronics™
Quiet Series™
RapidConfigure™
RapidConnect™
µSerDes™
ScalarPump™
SILENT SWITCHER®
SMART START™
SPM™
Stealth™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SyncFET™
TCM™
TinyBoost™
TinyBuck™
TinyPWM™
TinyPower™
TinyLogic®
TINYOPTO™
TruTranslation™
UHC™
UniFET™
UltraFET®
VCX™
Wire™
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO
IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE
OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE
RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS,
SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT
THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems which,
(a) are intended for surgical implant into the body, or (b) support
or sustain life, or (c) whose failure to perform when properly used
in accordance with instructions for use provided in the labeling,
can be reasonably expected to result in significant injury to the
user.
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or system, or to
affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or In Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Obsolete
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. I20
FPF1005-FPF1006 Rev. D
9
www.fairchildsemi.com
FPF1005-FPF1006 IntelliMAXTM Advanced Load Management Products
TRADEMARKS
Similar pages