Fairchild FST6800MTC 10-bit bus switch with pre-charged output Datasheet

Revised December 1999
FST6800
10-Bit Bus Switch with Pre-Charged Outputs
General Description
Features
The Fairchild Switch FST6800 provides 10-bits of highspeed CMOS TTL-compatible bus switching. The low on
resistance of the switch allows inputs to be connected to
outputs without adding propagation delay or generating
additional ground bounce noise. The device precharges
the B Port to a selectable bias voltage (BiasV) to minimize
live insertion noise.
■ 4Ω switch connection between two ports.
■ Minimal propagation delay through the switch.
■ Low lCC.
■ Zero bounce in flow-through mode.
■ Output precharge to minimize live insertion noise.
■ Control inputs compatible with TTL level.
The device is organized as a 10-bit switch with a bus
enable (OE) signal. When OE is LOW, the switch is ON
and Port A is connected to Port B. When OE is HIGH, the
switch is OPEN and the B Port is precharged to BiasV
through an equivalent 10-kΩ resistor.
Ordering Code:
Order Number
Package Number
Package Description
FST6800WM
M24B
24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide
FST6800QSC
MQA24
24-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150 Wide
FST6800MTC
MTC24
24-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Logic Diagram
Connection Diagram
Pin Descriptions
Truth Table
Pin Name
Description
OE
Bus Switch Enable
A
Bus A
B
Bus B
© 1999 Fairchild Semiconductor Corporation
DS500022
OE
B0–B9
Function
L
A0–A9
Connect
H
BiasV
Precharge
www.fairchildsemi.com
FST6800 10-Bit Bus Switch with Pre-Charged Outputs
June 1997
FST6800
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions (Note 3)
Supply Voltage (VCC )
−0.5V to +7.0V
DC Switch Voltage (VS)
−0.5V to +7.0V
Power Supply Operating (VCC)
4.0V to 5.5V
Bias V Voltage Range
−0.5V to +6.0V
Precharge Supply (BiasV)
1.5V to VCC
DC Input Voltage (VIN) (Note 2)
−0.5V to +7.0V
Input Voltage (VIN)
0V to 5.5V
0V to 5.5V
DC Input Diode Current (lIK) VIN<0V
−50mA
Output Voltage (VOUT)
DC Output (IOUT ) Sink Current
128mA
Input Rise and Fall Time (tr, tf)
+/− 100mA
DC VCC/GND Current (ICC/IGND)
Storage Temperature Range (TSTG)
Switch Control Input
−65°C to +150 °C
0nS/V to 5nS/V
Switch I/O
0nS/V to DC
−40 °C to +85 °C
Free Air Operating Temperature (TA)
Note 1: The Absolute Maximum Ratings are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum ratings.
The Recommended Operating Conditions tables will define the conditions
for actual device operation.
Note 2: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 3: Unused control inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
Symbol
Parameter
VCC
(V)
TA = −40 °C to +85 °C
Typ
(Note 4)
Min
Max
−1.2
Units
Conditions
IIN = −18mA
VIK
Clamp Diode Voltage
VIH
HIGH Level Input Voltage
4.0–5.5
VIL
LOW Level Input Voltage
4.0–5.5
0.8
V
II
Input Leakage Current
5.5
±1.0
µA
0≤ VIN ≤5.5V
IO
Output Current
4.5
mA
BiasV = 2.4V, B = 0
IOZ
OFF-STATE Leakage Current
5.5
±1.0
µA
0 ≤A ≤VCC
RON
Switch On Resistance
4.5
4
7
Ω
VIN = 0V, IIN = 64mA
(Note 5)
4.5
4
7
Ω
VIN = 0V, IIN = 30mA
4.5
2.0
V
V
0.25
4.5
8
15
Ω
VIN = 2.4V, IIN = 15mA
4.0
11
20
Ω
VIN = 2.4V, IIN = 15mA
ICC
Quiescent Supply Current
5.5
3
µA
VIN = VCC or GND, IOUT = 0
∆ ICC
Increase in ICC per Input
5.5
2.5
mA
One input at 3.4V
Other inputs at VCC or GND
Note 4: Typical values are at VCC = 5.0V and T A= +25°C
Note 5: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the
voltages on the two (A or B) pins.
www.fairchildsemi.com
2
TA = −40 °C to +85 °C,
CL = 50pF, RU = RD = 500Ω
Symbol
Parameter
VCC = 4.5 – 5.5V
Min
tPHL,tPLH
Prop Delay Bus to Bus (Note 6)
tPZH
Output Enable Time
tPZL
tPHZ
Output Disable Time
tPLZ
VCC = 4.0V
Max
Min
0.25
Units
Conditions
Figure No.
Max
0.25
ns
VI = OPEN
Figures 1,
2
1.5
6.2
6.5
ns
VI = OPEN, BiasV = GND
1.5
6.2
6.5
ns
VI = 7V, BiasV = 3V
1.5
6.1
6.5
ns
VI = OPEN, BiasV = GND
1.5
7.3
6.8
ns
VI = 7V, BiasV = 3V
Figure 1
Figure 2
Figure 1
Figure 2
Note 6: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On
resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage the source (zero output impedance).
Capacitance
Symbol
(Note 7)
Parameter
Typ
Max
Units
Conditions
CIN
Control Pin Input Capacitance
3
pF
VCC = 5.0V
CI/O
Input/Output Capacitance
5
pF
VCC, OE = 5.0V
Note 7: TA = +25°C, f = 1 MHz, Capacitance is characterized but not tested.
AC Loading and Waveforms
Note: Input driven by 50 Ω source terminated in 50 Ω
Note: C L includes load and stray capacitance
Note: Input PRR = 1.0 MHz, tW = 500 ns
FIGURE 1. AC Test Circuit
FIGURE 2. AC Waveforms
3
www.fairchildsemi.com
FST6800
AC Electrical Characteristics
FST6800
Physical Dimensions inches (millimeters) unless otherwise noted
24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide
Package Number M24B
24-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150 Wide
Package Number MQA24
www.fairchildsemi.com
4
FST6800 10-Bit Bus Switch with Pre-Charged Outputs
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
24-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC24
Technology Description
The Fairchild Switch family derives from and embodies Fairchild’s proven switch technology used for several years in its
74LVX3L384 (FST3384) bus switch product.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
device or system whose failure to perform can be reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
user.
www.fairchildsemi.com
5
www.fairchildsemi.com
Similar pages