Fairchild FSTU6800MTC 10-bit bus switch with precharged outputs and â 2v undershoot protection Datasheet

FSTU6800
10-Bit Bus Switch with Precharged Outputs
and −2V Undershoot Protection
General Description
Features
The Fairchild Switch FSTU6800 provides 10-bits of highspeed CMOS TTL-compatible bus switching. The low on
resistance of the switch allows inputs to be connected to
outputs without adding propagation delay or generating
additional ground bounce noise. Both the A Ports and the B
Ports have “undershoot hardened” circuit protection to support an extended input range to 2.0V below ground. Fairchild’s integrated Undershoot Hardened Circuit (UHC®)
senses undershoot at the I/Os, and responds by preventing
voltage differentials from developing and turning on the
switch. The device also precharges the B Port to a selectable bias voltage (BiasV) to minimize live insertion noise.
The device is organized as a 10-bit switch with a bus
enable (OE) signal. When OE is LOW, the switch is ON
and Port A is connected to Port B. When OE is HIGH, the
switch is OPEN and the B Port is precharged to BiasV
through an equivalent 10-kΩ resistor.
■ 4Ω switch connection between two ports.
■ Undershoot Hardened to -2.0V.
■ Soft enable turn-on to minimize bus-to-bus charge
sharing during enable.
■ Low lCC.
■ Zero bounce in flow-through mode.
■ Output precharge to minimize live insertion noise.
■ Control inputs compatible with TTL level.
■ See Applications Note AN-5008 for details.
Ordering Code:
Order Number
Package Number
Package Description
FSTU6800WM
M24B
24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide
FSTU6800QSC
MQA24
24-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150 Wide
FSTU6800MTC
MTC24
24-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Logic Diagram
Connection Diagram
Pin Descriptions
Pin Name
Description
OE
Bus Switch Enable
A
Bus A
B
Bus B
BiasV
Bus B Voltage Bias
Truth Table
OE
B0–B9
L
A0–A9
Connect
H
BiasV
Precharge
Function
UHC® is a registered trademark of Fairchild Semiconductor Corporation.
© 2000 Fairchild Semiconductor Corporation
DS500194
www.fairchildsemi.com
FSTU6800 10-Bit Bus Switch with Precharged Outputs
December 1998
Revised October 2006
FSTU6800
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions (Note 3)
Supply Voltage (VCC )
−0.5V to +7.0V
DC Switch Voltage (VS)
−2.0V to +7.0V
Power Supply Operating (VCC)
4.0V to 5.5V
Bias V Voltage Range
−0.5V to +7.0V
Precharge Supply (BiasV)
1.5V to VCC
DC Input Voltage (VIN) (Note 2)
−0.5V to +7.0V
Input Voltage (VIN)
0V to 5.5V
0V to 5.5V
DC Input Diode Current (lIK) VIN< 0V
−50mA
Output Voltage (VOUT)
DC Output (IOUT ) Sink Current
128mA
Input Rise and Fall Time (tr, tf)
+/− 100mA
DC VCC/GND Current (ICC/IGND)
Storage Temperature Range (TSTG)
Switch Control Input
−65°C to +150 °C
0 nS/V to 5 nS/V
Switch I/O
0nS/V to DC
−40 °C to +85 °C
Free Air Operating Temperature (TA)
Note 1: The Absolute Maximum Ratings are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum ratings.
The Recommended Operating Conditions tables will define the conditions
for actual device operation.
Note 2: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 3: Unused control inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
Symbol
VCC
(V)
Parameter
TA = −40 °C to +85 °C
Min
Typ
(Note 5)
Max
−1.2
Units
Conditions
IIN = −18mA
VIK
Clamp Diode Voltage
VIH
HIGH Level Input Voltage
4.0–5.5
VIL
LOW Level Input Voltage
4.0–5.5
0.8
V
II
Input Leakage Current
5.5
±1.0
µA
0 ≤ VIN ≤ 5.5V
IO
Output Current
4.5
mA
BiasV = 2.4V, B = 0
IOZ
OFF-STATE Leakage Current
5.5
±1.0
µA
0 ≤ A ≤ VCC, VIN = VIH
RON
Switch On Resistance
4.5
4
7
Ω
VS = 0V, IIN = 64 mA
(Note 4)
4.5
4
7
Ω
VS = 0V, IIN = 30 mA
4.5
8
15
Ω
VS = 2.4V, IIN = 15 mA
4.0
11
4.5
2.0
V
V
0.25
20
Ω
VS = 2.4V, IIN = 15 mA
ICC
Quiescent Supply Current
5.5
3
µA
VS = VCC or GND, IOUT = 0
∆ ICC
Increase in ICC per Input
5.5
2.5
mA
OE input at 3.4V
Other inputs at VCC or GND
IBIAS
Bias Pin Leakage Current
5.5
±1.0
µA
OE = 0V, B = 0V, BiasV = 5.5V
IOZU
Switch Undershoot Current
5.5
100
µA
IIN = −20 mA, OE = 5.5V, VOUT ≥ VIH
VIKU
Voltage Undershoot
5.5
−2.0
V
0.0 mA ≥ IIN ≥ −50 mA, OE = 5.5V
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the
voltages on the two (A or B) pins.
Note 5: Typical values are at VCC = 5.0V and T A= +25°C
www.fairchildsemi.com
2
TA = −40 °C to +85 °C,
CL = 50 pF, RU = RD = 500Ω
Symbol
Parameter
VCC = 4.5 – 5.5V
Min
tPHL,tPLH
Prop Delay Bus to Bus (Note 6)
tPZH
Output Enable Time
tPZL
tPHZ
Output Disable Time
tPLZ
VCC = 4.0V
Max
Min
Units
Conditions
Figure No.
Max
0.25
0.25
ns
VI = OPEN
7.0
30.0
35.0
ns
VI = OPEN
BiasV = GND
7.0
30.0
35.0
ns
VI = 7V
BiasV = 3V
1.0
6.1
6.5
ns
VI = OPEN
BiasV = GND
1.0
7.3
6.8
ns
VI = 7V
BiasV = 3V
Figures 1, 2
Figures 1, 2
Figures 1, 2
Note 6: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On
resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage the source (zero output impedance).
Capacitance
Symbol
(Note 7)
Parameter
Typ
Max
Units
Conditions
CIN
Control Pin Input Capacitance
3
pF
VCC = 5.0V
CI/O
Input/Output Capacitance
5
pF
VCC, OE = 5.0V
Note 7: TA = +25°C, f = 1 MHz, Capacitance is characterized but not tested.
AC Loading and Waveforms
Note: Input driven by 50 Ω source terminated in 50 Ω, RU = RD = 500 Ω
Note: C L includes load and stray capacitance, CL= 50 pF
Note: Input PRR = 1.0 MHz, tW = 500 ns
FIGURE 1. AC Test Circuit
FIGURE 2. AC Waveforms
3
www.fairchildsemi.com
FSTU6800
AC Electrical Characteristics
FSTU6800
Physical Dimensions inches (millimeters) unless otherwise noted
24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide
Package Number M24B
24-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150 Wide
Package Number MQA24
www.fairchildsemi.com
4
FSTU6800 10-Bit Bus Switch with Precharged Outputs
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
24-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC24
Technology Description
The Fairchild Switch family derives from and embodies Fairchild’s proven switch technology used for several years in its
74LVX3L384 (FST3384) bus switch product.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
device or system whose failure to perform can be reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
user.
www.fairchildsemi.com
5
www.fairchildsemi.com
Similar pages