MPD G215 Compact minidip, 2w single & dual output dc/dc converter Datasheet

MicroPower
Direct
Compact MiniDIP, 2W
Single & Dual Output
DC/DC Converters
G200 Series
Key Features
Miniature DIP Package
2W Output Power
3.6 MH MTBF
1.0 kVDC Isolation
Single & Dual Outputs
Low Cost
Electrical Specifications
Specifications typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min.
5 VDC Input
4.5
12 VDC Input 10.8
24 VDC Input 21.6
48 VDC Input 43.2
Internal Capacitor
Input Voltage Range
Input Filter
Reverse Polarity Input Current
Typ.
5.0
12.0
24.0
48.0
Max.
5.5
13.2
26.4
52.8
Units
0.3
A
Max.
!3.0
!1.0
!1.5
Units
%
%
%
150
200
5
mV P - P
mV P - P
mV rms
%
%/1C
VDC
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
Conditions
Min.
Typ.
!1.0
Dual Output , Balanced Loads
!0.1
For Vin Change of 1%
!1.2
See Model Selection Guide
100
Over Line, Load & Temp.
120
!0.01
Momentary (0.5 Sec.)
!0.02
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
500 VDC
100 kHz, 1V
Min.
1,000
1,000
50
Typ.
Max.
80
80
120
100
Units
VDC
MΩ
pF
kHz
Max.
+70
+125
Units
1C
1C
95
%
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Min.
Typ.
-40
+25
-40
Free Air Convection
RH, Non-condensing
Physical
Case Size, 5V, 12V & 24V Input Models
Case Size, 48VDC Input Models
Case Material
Weight
0.80 x 0.40 x 0.27 Inches (20.32 x 10.16 x 6.85 mm)
0.80 x 0.40 x 0.30 Inches (20.32 x 10.16 x 7.50 mm)
Non-Conductive Black Plastic
0.09 Oz (2.7g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 251C, Gnd Benign
Min.
Typ.
3.6
Max.
Units
MHours
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
9.0
18.0
30.0
55.0
650
Units
Absolute Maximum Ratings
Parameter
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
All Models
Input Voltage Surge (1 Sec)
Internal Power Dissipation
VDC
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
MicroPower Direct
TEL: (781) 344-8226
FAX: (781) 344-8481
E-Mail: [email protected]
WEB: www/micropowerdirect.com
Model Selection Guide
Input
Output
Load
Fuse Rating
Efficiency
Voltage (VDC)
Current (mA)
Slow-Blow
Voltage Current
Current Regulation
(%, Typ)
(%, Max)
(mA)
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min)
5
4.5 - 5.5
452
35
3.3
500.0
10.0
11
73
1,000
5
4.5 - 5.5
526
35
5.0
400.0
8.0
11
76
1,000
5
4.5 - 5.5
495
35
12.0
165.0
3.0
7
80
1,000
5
4.5 - 5.5
499
35
15.0
133.0
2.5
7
80
1,000
5
4.5 - 5.5
519
35
10
77
1,000
!5.0
!200.0
!4.0
5
4.5 - 5.5
504
35
7
79
1,000
!12.0
!83.0
!1.5
5
4.5 - 5.5
501
35
7
79
1,000
!15.0
!66.0
!1.0
12
10.8 - 13.2
185
25
3.3
500.0
10.0
8
74
500
12
10.8 - 13.2
212
25
5.0
400.0
8.0
8
78
500
12
10.8 - 13.2
200
25
12.0
165.0
3.0
5
82
500
12
10.8 - 13.2
200
25
15.0
133.0
2.5
5
83
500
12
10.8 - 13.2
222
25
8
75
500
!5.0
!200.0
!4.0
12
10.8 - 13.2
201
25
5
82
500
!12.0
!83.0
!1.5
12
10.8 - 13.2
200
25
5
82
500
!15.0
!66.0
!1.0
24
21.6 - 26.4
92
10
3.3
500.0
10.0
8
74
200
24
21.6 - 26.4
108
10
5.0
400.0
8.0
8
77
200
24
21.6 - 26.4
101
10
12.0
165.0
3.0
5
81
200
24
21.6 - 26.4
101
10
15.0
133.0
2.5
5
82
200
24
21.6 - 26.4
111
10
8
75
200
!5.0
!200.0
!4.0
24
21.6 - 26.4
102
10
5
81
200
!12.0
!83.0
!1.5
24
21.6 - 26.4
100
10
5
82
200
!15.0
!66.0
!1.0
48
43.2 - 54.8
28
6
3.3
500.0
10.0
8
74
100
48
43.2 - 54.8
27
6
5.0
400.0
8.0
8
77
100
48
43.2 - 54.8
26
6
12.0
165.0
3.0
5
81
100
48
43.2 - 54.8
25
6
15.0
133.0
2.5
5
82
100
48
43.2 - 54.8
28
6
8
75
100
!5.0
!200.0
!4.0
48
43.2 - 54.8
26
6
5
81
100
!12.0
!83.0
!1.5
48
43.2 - 54.8
25
6
5
82
100
!15.0
!66.0
!1.0
Model
Number
G201
G202
G203
G204
G205
G206
G207
G211
G212
G213
G214
G215
G216
G217
G221
G222
G223
G224
G225
G226
G227
G231
G232
G233
G234
G235
G236
G237
Notes:
Derating Curve
1. Dual output units may be connected to provide a 10V,
24V or 30 VDC output. To do this, connect the load
across the positive (+Vout) and negative (-Vout)
outputs and float the output common.
2. These units do not require external comonents to
operate, but the use of an input capacitor (10 µF) may
enhance performance in some applications. An output
capacitor (4.7 µF to 10 µF) may be used to reduce
ripple.
100
Output Power %
80
Mechanical Dimensions
60
40
20
Side
“T”
0
-40
-20
0
5
0.12
(3.05)
0.60 (15.24)
0.80 (20.32)
1
7
0.40
(10.2)
Bottom
14
0.01
(0.25)
11
9
25
35
45
55
65
75
85
95
105
Ambient Temperature 1C
Pin Connections
0.10
(2.54)
0.10
(2.54)
15
8
0.01
(0.25)
0.05
(1.25)
Note: “T” = 0.27 (6.85) For 5, 12 & 24 VDC Input Models
0.30 (7.50) For 48 VDC Input Models
MicroPower
Direct
Pin
Single
Dual
1
-Vin
-Vin
7
NC
NC
8
No Pin
Common
9
+Vout
+Vout
11
-Vout
-Vout
14
+Vin
+Vin
Capacitive Load
Single Output Dual Output
µF Max
µF Max
470
!390
NC = No Connection
Notes: All dimensions are typical in inches (mm)
Tolerance x.xx = !0.01 (!0.25)
Pin 1 is marked by a “dot” or indentation on the top of the unit
232 Tosca Drive, Stoughton, MA 02072
www.micropowerdirect.com
[email protected]
phone: (781) 344 - 8226 * fax: (781) 344 - 8481
Similar pages