Intel GE28F640C3BA70 Advanced boot block flash memory (c3) Datasheet

Intel£ Advanced+ Boot Block Flash
Memory (C3)
28F800C3, 28F160C3, 28F320C3, 28F640C3 (x16)
Datasheet
Product Features
■
■
■
■
■
■
■
Flexible SmartVoltage Technology
— 2.7 V– 3.6 V Read/Program/Erase
— 12 V for Fast Production Programming
1.65 V–2.5 V or 2.7 V–3.6 V I/O Option
— Reduces Overall System Power
High Performance
— 2.7 V– 3.6 V: 70 ns Max Access Time
Optimized Architecture for Code Plus
Data Storage
— Eight 4 Kword Blocks, Top or Bottom
Parameter Boot
— Up to One Hundred-Twenty-Seven 32
Kword Blocks
— Fast Program Suspend Capability
— Fast Erase Suspend Capability
Flexible Block Locking
— Lock/Unlock Any Block
— Full Protection on Power-Up
— WP# Pin for Hardware Block Protection
Low Power Consumption
— 9 mA Typical Read
— 7 A Typical Standby with Automatic
Power Savings Feature (APS)
Extended Temperature Operation
— –40 °C to +85 °C
■
■
■
■
■
■
■
128-bit Protection Register
— 64 bit Unique Device Identifier
— 64 bit User Programmable OTP Cells
Extended Cycling Capability
— Minimum 100,000 Block Erase Cycles
Software
— Intel® Flash Data Integrator (FDI)
— Supports Top or Bottom Boot Storage,
Streaming Data (e.g., voice)
— Intel Basic Command Set
— Common Flash Interface (CFI)
Standard Surface Mount Packaging
— 48-Ball µBGA*/VFBGA
— 64-Ball Easy BGA Packages
— 48-Lead TSOP Package
ETOX™ VIII (0.13 µm) Flash
Technology
— 16, 32 Mbit
ETOX™ VII (0.18 µm) Flash Technology
— 16, 32, 64 Mbit
ETOX™ VI (0.25 µm) Flash Technology
— 8, 16 and 32 Mbit
The Intel® Advanced+ Book Block Flash Memory (C3) device, manufactured on Intel’s latest
0.13 µm and 0.18 µm technologies, represents a feature-rich solution for low-power applications.
The C3 device incorporates low-voltage capability (3 V read, program, and erase) with highspeed, low-power operation. Flexible block locking allows any block to be independently locked
or unlocked. Add to this the Intel® Flash Data Integrator (FDI) software and you have a costeffective, flexible, monolithic code plus data storage solution. Intel® Advanced+ Boot Block Flash
Memory (C3) products will be available in 48-lead TSOP, 48-ball CSP, and 64-ball Easy BGA
packages. Additional information on this product family can be obtained by accessing the Intel®
Flash website: http://www.intel.com/design/flash.
Notice: This specification is subject to change without notice. Verify with your local Intel sales
office that you have the latest datasheet before finalizing a design.
Order Number: 290645-017
October 2003
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY
ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN
INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS
ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES
RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER
INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for
future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
The 28F800C3, 28F160C3, 28F320C3, 28F640C3 may contain design defects or errors known as errata which may cause the product to deviate from
published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800548-4725 or by visiting Intel's website at http://www.intel.com.
Copyright © Intel Corporation, 2003
*Third-party brands and names are the property of their respective owners.
2
Datasheet
Contents
Contents
1.0
Introduction....................................................................................................................................7
1.1
1.2
1.3
2.0
Device Description ........................................................................................................................8
2.1
2.2
2.3
2.4
2.5
3.0
Bus Operations ...................................................................................................................17
3.1.1 Read ......................................................................................................................17
3.1.2 Write ......................................................................................................................17
3.1.3 Output Disable .......................................................................................................17
3.1.4 Standby..................................................................................................................18
3.1.5 Reset .....................................................................................................................18
Modes of Operation .....................................................................................................................19
4.1
4.2
4.3
5.0
Product Overview .................................................................................................................8
Ballout Diagram ....................................................................................................................8
Signal Descriptions .............................................................................................................13
Block Diagram ....................................................................................................................14
Memory Map .......................................................................................................................15
Device Operations .......................................................................................................................17
3.1
4.0
Document Purpose ...............................................................................................................7
Nomenclature .......................................................................................................................7
Conventions..........................................................................................................................7
Read Mode .........................................................................................................................19
4.1.1 Read Array.............................................................................................................19
4.1.2 Read Identifier .......................................................................................................19
4.1.3 CFI Query ..............................................................................................................20
4.1.4 Read Status Register.............................................................................................20
4.1.4.1 Clear Status Register .............................................................................21
Program Mode ....................................................................................................................21
4.2.1 12-Volt Production Programming...........................................................................21
4.2.2 Suspending and Resuming Program .....................................................................22
Erase Mode ........................................................................................................................22
4.3.1 Suspending and Resuming Erase .........................................................................23
Security Modes ............................................................................................................................27
5.1
5.2
5.3
5.4
5.5
5.6
Datasheet
Flexible Block Locking ........................................................................................................27
5.1.1 Locking Operation..................................................................................................28
5.1.1.1 Locked State ..........................................................................................28
5.1.1.2 Unlocked State.......................................................................................28
5.1.1.3 Lock-Down State....................................................................................28
Reading Block-Lock Status.................................................................................................28
Locking Operations during Erase Suspend ........................................................................29
Status Register Error Checking ..........................................................................................29
128-Bit Protection Register .................................................................................................29
5.5.1 Reading the Protection Register ............................................................................30
5.5.2 Programming the Protection Register....................................................................30
5.5.3 Locking the Protection Register .............................................................................30
VPP Program and Erase Voltages ......................................................................................30
3
Contents
5.6.1
6.0
Power Consumption.................................................................................................................... 32
6.1
6.2
6.3
6.4
6.5
6.6
7.0
Active Power (Program/Erase/Read).................................................................................. 32
Automatic Power Savings (APS) ........................................................................................ 32
Standby Power ................................................................................................................... 32
Deep Power-Down Mode.................................................................................................... 32
Power and Reset Considerations ....................................................................................... 33
6.5.1 Power-Up/Down Characteristics............................................................................ 33
6.5.2 RP# Connected to System Reset .......................................................................... 33
6.5.3 VCC, VPP and RP# Transitions ............................................................................ 33
Power Supply Decoupling................................................................................................... 34
Thermal and DC Characteristics ................................................................................................ 34
7.1
7.2
7.3
7.4
8.0
Program Protection................................................................................................ 31
Absolute Maximum Ratings ................................................................................................ 34
Operating Conditions .......................................................................................................... 35
DC Current Characteristics................................................................................................. 35
DC Voltage Characteristics................................................................................................. 38
AC Characteristics ...................................................................................................................... 39
8.1
8.2
8.3
8.4
8.5
8.6
AC Read Characteristics .................................................................................................... 39
AC Write Characteristics..................................................................................................... 43
Erase and Program Timings ............................................................................................... 47
Reset Specifications ........................................................................................................... 48
AC I/O Test Conditions ....................................................................................................... 49
Device Capacitance............................................................................................................ 49
Appendix A Write State Machine States.............................................................................................50
Appendix B Flow Charts ......................................................................................................................52
Appendix C Common Flash Interface.................................................................................................58
Appendix D Mechanical Specifications..............................................................................................64
Appendix E Additional Information ....................................................................................................67
Appendix F Ordering Information .......................................................................................................68
4
Datasheet
Contents
Revision History
Date of
Revision
Version
05/12/98
-001
Original version
-002
48-Lead TSOP package diagram change
µBGA package diagrams change
32-Mbit ordering information change (Section 6)
CFI Query Structure Output Table Change (Table C2)
CFI Primary-Vendor Specific Extended Query Table Change for Optional
Features and Command Support change (Table C8)
Protection Register Address Change
IPPD test conditions clarification (Section 4.3)
µBGA package top side mark information clarification (Section 6)
10/03/98
-003
Byte-Wide Protection Register Address change
VIH Specification change (Section 4.3)
VIL Maximum Specification change (Section 4.3)
ICCS test conditions clarification (Section 4.3)
Added Command Sequence Error Note (Table 7)
Datasheet renamed from 3 Volt Advanced Boot Block, 8-, 16-, 32-Mbit Flash
Memory Family.
12/04/98
-004
Added tBHWH/tBHEH and tQVBL (Section 4.6)
Programming the Protection Register clarification (Section 3.4.2)
12/31/98
-005
Removed all references to x8 configurations
02/24/99
-006
Removed reference to 40-Lead TSOP from front page
06/10/99
-007
Added Easy BGA package (Section 1.2)
Removed 1.8 V I/O references
Locking Operations Flowchart changed (Appendix B)
Added tWHGL (Section 4.6)
CFI Primary Vendor-Specific Extended Query changed (Appendix C)
03/20/00
-008
04/24/00
-009
07/21/98
Description
Max ICCD changed to 25 µA
Table 10, added note indicating VCCMax = 3.3 V for 32-Mbit device
Added specifications for 0.18 micron product offerings throughout document
Added 64-Mbit density
Changed references of 32Mbit 80ns devices to 70ns devices to reflect the
faster product offering.
10/12/00
-010
Changed VccMax=3.3V reference to indicate that the affected product is the
0.25µm 32Mbit device.
Minor text edits throughout document.
Added 1.8v I/O operation documentation where applicable
Added TSOP PCN ‘Pin-1’ indicator information
Changed references in 8 x 8 BGA pinout diagrams from ‘GND’ to ‘Vssq’
7/20/01
-011
Added ‘Vssq’ to Pin Descriptions Information
Removed 0.4 µm references in DC characteristics table
Corrected 64Mb package Ordering Information from 48-uBGA to 48-VFBGA
Corrected ‘bottom’ parameter block sizes to on 8Mb device to 8 x 4KWords
Minor text edits throughout document
10/02/01
-012
2/05/02
-013
Added specifications for 0.13 micron product offerings throughout document
Corrected Iccw / Ippw / Icces /Ippes values.
Added mechanicals for 16Mb and 64Mb
Minor text edits throughout document.
Datasheet
5
Contents
Date of
Revision
Version
Description
Updated 64Mb product offerings.
Updated 16Mb product offerings.
4/05/02
-014
Revised and corrected DC Characteristics Table.
Added mechanicals for Easy BGA.
Minor text edits throughout document.
6
3/06/03
-016
Complete technical update.
10/03
-017
Corrected information in the Device Geometry Details table, address 0x34.
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
1.0
Introduction
1.1
Document Purpose
This datasheet contains the specifications for the Intel® Advanced+ Boot Block Flash Memory
(C3) device family. These flash memories add features such as instant block locking and protection
registers that can be used to enhance the security of systems.
1.2
Nomenclature
0x
0b
Byte
Word
Kword
Mword
Kb
KB
Mb
MB
APS
CUI
OTP
PR
PRD
PLR
RFU
SR
SRD
WSM
1.3
Hexadecimal prefix
Binary prefix
8 bits
16 bits
1024 words
1,048,576 words
1024 bits
1024 bytes
1,048,576 bits
1,048,576 bytes
Automatic Power Savings
Command User Interface
One Time Programmable
Protection Register
Protection Register Data
Protection Lock Register
Reserved for Future Use
Status Register
Status Register Data
Write State Machine
Conventions
The terms pin and signal are often used interchangeably to refer to the external signal connections
on the package. (ball is the term used for CSP).
Group Membership Brackets: Square brackets will be used to designate group membership or to
define a group of signals with similar function (i.e. A[21:1], SR[4:1])
Set: When referring to registers, the term set means the bit is a logical 1.
Clear: When referring to registers, the term clear means the bit is a logical 0.
Block: A group of bits (or words) that erase simultaneously with one block erase instruction.
Main Block: A block that contains 32 Kwords.
Parameter Block: A block that contains 4 Kwords.
Datasheet
7
Intel£ Advanced+ Boot Block Flash Memory (C3)
2.0
Device Description
This section provides an overview of the Intel® Advanced+ Boot Block Flash Memory (C3) device
features, packaging, signal naming, and device architecture.
2.1
Product Overview
The C3 device provides high-performance asynchronous reads in package-compatible densities
with a 16 bit data bus. Individually-erasable memory blocks are optimally sized for code and data
storage. Eight 4 Kword parameter blocks are located in the boot block at either the top or bottom of
the device’s memory map. The rest of the memory array is grouped into 32 Kword main blocks.
The device supports read-array mode operations at various I/O voltages (1.8 V and 3 V) and erase
and program operations at 3 V or 12 V VPP. With the 3 V I/O option, VCC and VPP can be tied
together for a simple, ultra-low-power design. In addition to I/O voltage flexibility, the dedicated
VPP input provides complete data protection when VPP ≤ VPPLK.
The device features a 128-bit protection register enabling security techniques and data protection
schemes through a combination of factory-programmed and user-programmable OTP data
registers. Zero-latency locking/unlocking on any memory block provides instant and complete
protection for critical system code and data. Additional block lock-down capability provides
hardware protection where software commands alone cannot change the block’s protection status.
A command User Interface(CUI) serves as the interface between the system processor and internal
operation of the device. A valid command sequence issued to the CUI initiates device automation.
An internal Write State Machine (WSM) automatically executes the algorithms and timings
necessary for block erase, program, and lock-bit configuration operations.
The device offers three low-power saving features: Automatic Power Savings (APS), standby
mode, and deep power-down mode. The device automatically enters APS mode following read
cycle completion. Standby mode begins when the system deselects the flash memory by
deasserting CE#. The deep power-down mode begins when RP# is asserted, which deselects the
memory and places the outputs in a high-impedance state, producing ultra-low power savings.
Combined, these three power-savings features significantly enhanced power consumption
flexibility.
2.2
Ballout Diagram
The C3 device is available in 48-lead TSOP, 48-ball VF BGA, 48-ball µBGA, and Easy BGA
packages. (Refer to Figure 1 on page 9, Figure 3 on page 11, and Figure 4 on page 12,
respectively.)
8
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 1. 48-Lead TSOP Package
64 M
32 M
16 M
A15
A14
A13
A12
A11
A10
A9
A8
A21
A20
WE#
RP#
VPP
WP#
A19
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Advanced+ Boot Block
48-Lead TSOP
12 mm x 20 mm
TOP VIEW
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
VCCQ
GND
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
GND
CE#
A0
NOTES:
1. For lower densities, upper address should be treated as NC. For example, a 16-Mbit device will have NC on
Pins 9 and 10.
Datasheet
9
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 2. Mark for Pin-1 indicator on 48-Lead 8Mb, 16Mb and 32Mb TSOP
Current Mark:
New Mark:
Note:
Table 1.
The topside marking on 8 Mb, 16 Mb, and 32 Mb Intel£ Advanced and Advanced + Boot Block
48L TSOP products will convert to a white ink triangle as a Pin 1 indicator. Products without the
white triangle will continue to use a dimple as a Pin 1 indicator. There are no other changes in
package size, materials, functionality, customer handling, or manufacturability. Product will
continue to meet Intel stringent quality requirements. Products affected are Intel Ordering Codes
shown in Table 1.
48-Lead TSOP
Extended 64 Mbit
TE28F640C3TC80
TE28F640C3BC80
Extended 32 Mbit
Extended 16 Mbit
Extended 8 Mbit
TE28F320C3TD70
TE28F320C3BD70
TE28F160C3TD70
TE28F160C3BD70
TE28F800C3TA90
TE28F800C3BA90
TE28F320C3TC70
TE28F320C3BC70
TE28F160C3TC80
TE28F160C3BC80
TE28F800C3TA110
TE28F800C3BA110
TE28F320C3TC90
TE28F320C3BC90
TE28F160C3TA90
TE28F160C3BA90
TE28F320C3TA100
TE28F320C3BA100
TE28F160C3TA110
TE28F160C3BA110
TE28F320C3TA110
TE28F320C3BA110
10
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 3. 48-Ball µBGA* and 48-Ball Very Fine Pitch BGA (VF BGA) Chip Size Package
(Top View, Ball Down)1,2,3
1
2
3
4
5
6
7
8
16M
A
A13
A11
A8
VPP
WP#
A19
A7
A4
B
A14
A10
WE#
RP#
A18
A17
A5
A2
64M
32M
C
A15
A12
A9
A21
A20
A6
A3
A1
D
A16
D14
D5
D11
D2
D8
CE#
A0
E
VCCQ
D15
D6
D12
D3
D9
D0
GND
F
GND
D7
D13
D4
VCC
D10
D1
OE#
NOTES:
1. Shaded connections indicate the upgrade address connections. Routing is not recommended in this area.
2. A19 denotes 16 Mbit; A20 denotes 32 Mbit; A21 denotes 64 Mbit.
3. Unused address balls are not populated.
Datasheet
11
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 4. 64-Ball Easy BGA Package1,2
1
2
3
4
5
6
7
8
A
8
7
6
5
4
3
2
1
VPP
A18
A
A1
A6
A18
VPP
VCC GND A10
A15
B
A15
A10 GND VCC
A6
A1
A14
A11 A20(1) DU RP# A19(1) A17
A2
A13
A12 A21(1) DU WE# WP# A7
A3
A9
A8
A4
B
A2
A17 A19(1) RP# DU A20(1) A11
A14
C
C
A3
A7
WP# WE# DU A21(1) A12
A13
D
D
DU DU
A8
A9
DQ8 DQ1 DQ9 DQ3 DQ12 DQ6
DU
DU
A4
A5
DU
DU
E
DU
DU
DU DU
A5
E
F
DU
DU DQ6 DQ12 DQ3 DQ9 DQ1 DQ8
DU
DU DQ14 DQ5 DQ11 DQ10 DQ0 CE#
F
CE# DQ0 DQ10 DQ11 DQ5 DQ14 DU
DU
G
G
A0
VSSQ DQ2 DQ4 DQ13 DQ15 VSSQ A16
H
A16 VSSQ D15
D13
DQ4 DQ2 VSSQ
A0
DU VCCQ D7
VSSQ VCC VCCQ OE# A22(2)
H
A22(2) OE# VCCQ VCC VSSQ DQ7 VCCQ
Top View- Ball Side
DU
Bottom View - Ball Side
NOTES:
1. A19 denotes 16 Mbit; A20 denotes 32 Mbit; A21 denotes 64 Mbit.
2. Unused address balls are not populated.
12
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
2.3
Signal Descriptions
Table 2 lists the active signals used and provides a brief description of each.
Table 2.
Symbol
Signal Descriptions
Type
Name and Function
ADDRESS INPUTS for memory addresses. Address are internally latched during a program or erase
cycle.
A[MAX:0]
INPUT
8 Mbit: AMAX= A18
16 Mbit: AMAX = A19
32 Mbit: AMAX = A20
64 Mbit: AMAX = A21
INPUT/
OUTPUT
DATA INPUTS/OUTPUTS: Inputs data and commands during a write cycle; outputs data during read
cycles. Inputs commands to the Command User Interface when CE# and WE# are active. Data is
internally latched. The data pins float to tri-state when the chip is de-selected or the outputs are
disabled.
CE#
INPUT
CHIP ENABLE: Active-low input. Activates the internal control logic, input buffers, decoders and sense
amplifiers. CE# is active low. CE# high de-selects the memory device and reduces power consumption
to standby levels.
OE#
INPUT
OUTPUT ENABLE: Active-low input. Enables the device’s outputs through the data buffers during a
Read operation.
DQ[15:0]
RESET/DEEP POWER-DOWN: Active-low input.
RP#
INPUT
WE#
INPUT
When RP# is at logic low, the device is in reset/deep power-down mode, which drives the outputs to
High-Z, resets the Write State Machine, and minimizes current levels (ICCD).
When RP# is at logic high, the device is in standard operation. When RP# transitions from logic-low to
logic-high, the device resets all blocks to locked and defaults to the read array mode.
WRITE ENABLE: Active-low input. WE# controls writes to the device. Address and data are latched on
the rising edge of the WE# pulse.
WRITE PROTECT: Active-low input.
WP#
INPUT
When WP# is a logic low, the lock-down mechanism is enabled and blocks marked lock-down cannot
be unlocked through software.
When WP# is logic high, the lock-down mechanism is disabled and blocks previously locked-down are
now locked and can be unlocked and locked through software. After WP# goes low, any blocks
previously marked lock-down revert to the lock-down state.
See Section 5.0, “Security Modes” on page 27 for details on block locking.
PROGRAM/ERASE POWER SUPPLY: Operates as an input at logic levels to control complete device
protection. Supplies power for accelerated Program and Erase operations in 12 V ± 5% range. This pin
cannot be left floating.
Lower VPP ≤ VPPLK to protect all contents against Program and Erase commands.
Set VPP = VCC for in-system Read, Program and Erase operations. In this configuration, VPP can
drop as low as 1.65 V to allow for resistor or diode drop from the system supply.
Apply VPP to 12 V ± 5% for faster program and erase in a production environment. Applying 12 V ± 5%
to VPP can only be done for a maximum of 1000 cycles on the main blocks and 2500 cycles on the
boot blocks. VPP may be connected to 12 V for a total of 80 hours maximum. See Section 5.6 for
details on VPP voltage configurations.
VPP
INPUT/
POWER
VCC
POWER
DEVICE CORE POWER SUPPLY: Supplies power for device operations.
VCCQ
POWER
OUTPUT POWER SUPPLY: Output-driven source voltage. This ball can be tied directly to VCC if
operating within VCC range.
GND
POWER
GROUND: For all internal circuitry. All ground inputs must be connected.
DU
-
DON’T USE: Do not use this ball. This ball should not be connected to any power supplies, signals or
other balls, and must be left floating.
NC
-
NO CONNECT: Pin must be left floating.
Datasheet
13
Intel£ Advanced+ Boot Block Flash Memory (C3)
2.4
Block Diagram
DQ 0-DQ 15
VCCQ
Input Buffer
Identifier
Register
Status
Register
Power
Reduction
Control
Data
Comparator
Y-Decoder
Y-Gating/Sensing
Data
Re gi ster
Outp ut
M ulti ple xer
Output Buffer
I/O Logic
CE#
WE#
OE#
RP#
Command
User
Interface
WP#
Address
Counter
32- KWord
M ain Blo ck
X-Decoder
4 -KWor d
Para mete r B loc k
32- KWord
M ain Blo ck
Address
Latch
14
Write State
Machine
Input Buffer
4 -KWor d
Para mete r B loc k
A[MAX:MIN]
Program/Erase
Voltage Switch
VPP
VCC
GND
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
2.5
Memory Map
The C3 device is asymmetrically blocked, which enables system code and data integration within a
single flash device. The bulk of the array is divided into 32 Kword main blocks that can store code
or data, and 4 Kword boot blocks to facilitate storage of boot code or for frequently changing small
parameters. See Table 3, “Top Boot Memory Map” on page 15 and Table 4, “Bottom Boot Memory
Map” on page 16 for details.
Table 3.
Top Boot Memory Map
Size
(KW)
Blk
8-Mbit
Memory
Addressing
(HEX)
Size
(KW)
Blk
16-Mbit
Memory
Addressing
(HEX)
Size
(KW)
Blk
32-Mbit
Memory
Addressing
(HEX)
Size
(KW)
Blk
64-Mbit Memory
Addressing
(HEX)
4
22
7F0007FFFF
4
38
FF000-FFFFF
4
70
1FF0001FFFFF
4
134
3FF000-3FFFFF
4
21
7E0007EFFF
4
37
FE000-FEFFF
4
69
1FE0001FEFFF
4
133
3FE000-3FEFFF
4
20
7D0007DFFF
4
36
FD000-FDFFF
4
68
1FD0001FDFFF
4
132
3FD000-3FDFFF
4
19
7C0007CFFF
4
35
FC000-FCFFF
4
67
1FC0001FCFFF
4
131
3FC000-3FCFFF
4
18
7B0007BFFF
4
34
FB000-FBFFF
4
66
1FB0001FBFFF
4
130
3FB000-3FBFFF
4
17
7A0007AFFF
4
33
FA000-FAFFF
4
65
1FA0001FAFFF
4
129
3FA000-3FAFFF
4
16
79000-79FFF
4
32
F9000-F9FFF
4
64
1F90001F9FFF
4
128
3F9000-3F9FFF
4
15
78000-78FFF
4
31
F8000-F8FFF
4
63
1F80001F8FFF
4
127
3F8000-3F8FFF
32
14
70000-77FFF
32
30
F0000-F7FFF
32
62
1F00001F7FFF
32
126
3F0000-3F7FFF
32
13
68000-6FFFF
32
29
E8000-EFFFF
32
61
1E80001EFFFF
32
125
3E8000-3EFFFF
32
12
60000-67FFF
32
28
E0000-E7FFF
32
60
1E00001E7FFF
32
124
3E0000-3E7FFF
32
11
58000-5FFFF
32
27
D8000-DFFFF
32
59
1D80001DFFFF
32
123
3D8000-3DFFFF
...
...
...
...
...
...
...
...
...
...
...
...
32
2
10000-17FFF
32
2
10000-17FFF
32
2
10000-17FFF
32
2
10000-17FFF
32
1
8000-0FFFF
32
1
08000-0FFFF
32
1
08000-0FFFF
32
1
08000-0FFFF
32
0
0000-07FFF
32
0
00000-07FFF
32
0
00000-07FFF
32
0
00000-07FFF
Datasheet
15
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 4.
Bottom Boot Memory Map
Size
(KW)
Blk
8-Mbit
Memory
Addressing
(HEX)
Size
(KW)
Blk
16-Mbit
Memory
Addressing
(HEX)
Size
(KW)
Blk
32-Mbit
Memory
Addressing
(HEX)
Size
(KW)
Blk
64-Mbit Memory
Addressing
(HEX)
32
22
78000-7FFFF
32
38
F8000-FFFFF
32
70
1F8000-1FFFFF
32
134
3F8000-3FFFFF
32
21
70000-77FFF
32
37
F0000-F7FFF
32
69
1F0000-1F7FFF
32
133
3F0000-3F7FFF
32
20
68000-6FFFF
32
36
E8000-EFFFF
32
68
1E8000-1EFFFF
32
132
3E8000-3EFFFF
32
19
60000-67FFF
32
35
E0000-E7FFF
32
67
1E0000-1E7FFF
32
131
3E0000-3E7FFF
...
...
...
...
...
...
...
...
...
.
...
...
32
10
18000-1FFFF
32
10
18000-1FFFF
32
10
18000-1FFFF
32
10
18000-1FFFF
32
9
10000-17FFF
32
9
10000-17FFF
32
9
10000-17FFF
32
9
10000-17FFF
32
8
08000-0FFFF
32
8
08000-0FFFF
32
8
08000-0FFFF
32
8
08000-0FFFF
4
7
07000-07FFF
4
7
07000-07FFF
4
7
07000-07FFF
4
7
07000-07FFF
4
6
06000-06FFF
4
6
06000-06FFF
4
6
06000-06FFF
4
6
06000-06FFF
4
5
05000-05FFF
4
5
05000-05FFF
4
5
05000-05FFF
4
5
05000-05FFF
4
4
04000-04FFF
4
4
04000-04FFF
4
4
04000-04FFF
4
4
04000-04FFF
4
3
03000-03FFF
4
3
03000-03FFF
4
3
03000-03FFF
4
3
03000-03FFF
4
2
02000-02FFF
4
2
02000-02FFF
4
2
02000-02FFF
4
2
02000-02FFF
4
1
01000-01FFF
4
1
01000-01FFF
4
1
01000-01FFF
4
1
01000-01FFF
4
0
00000-00FFF
4
0
00000-00FFF
4
0
00000-00FFF
4
0
00000-00FFF
16
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
3.0
Device Operations
The C3 device uses a CUI and automated algorithms to simplify Program and Erase operations.
The CUI allows for 100% CMOS-level control inputs and fixed power supplies during erasure and
programming.
The internal WSM completely automates Program and Erase operations while the CUI signals the
start of an operation and the status register reports device status. The CUI handles the WE#
interface to the data and address latches, as well as system status requests during WSM operation.
3.1
Bus Operations
The C3 device performs read, program, and erase operations in-system via the local CPU or
microcontroller. Four control pins (CE#, OE#, WE#, and RP#) manage the data flow in and out of
the flash device. Table 5 on page 17 summarizes these bus operations.
Table 5.
Bus Operations
Mode
RP#
CE#
OE#
WE#
DQ[15:0]
Read
VIH
VIL
VIL
VIH
DOUT
Write
VIH
VIL
VIH
VIL
DIN
Output Disable
VIH
VIL
VIH
VIH
High-Z
Standby
VIH
VIH
X
X
High-Z
Reset
VIL
X
X
X
High-Z
NOTE: X = Don’t Care (VIL or VIH)
3.1.1
Read
When performing a read cycle, CE# and OE# must be asserted; WE# and RP# must be deasserted.
CE# is the device selection control; when active low, it enables the flash memory device. OE# is
the data output control; when low, data is output on DQ[15:0]. See Figure 8, “Read Operation
Waveform” on page 42.
3.1.2
Write
A write cycle occurs when both CE# and WE# are low; RP# and OE# are high. Commands are
issued to the Command User Interface (CUI). The CUI does not occupy an addressable memory
location. Address and data are latched on the rising edge of the WE# or CE# pulse, whichever
occurs first. See Figure 9, “Write Operations Waveform” on page 47.
3.1.3
Output Disable
With OE# at a logic-high level (VIH), the device outputs are disabled. DQ[15:0] are placed in a
high-impedance state.
Datasheet
17
Intel£ Advanced+ Boot Block Flash Memory (C3)
3.1.4
Standby
Deselecting the device by bringing CE# to a logic-high level (VIH) places the device in standby
mode, which substantially reduces device power consumption without any latency for subsequent
read accesses. In standby, outputs are placed in a high-impedance state independent of OE#. If
deselected during a Program or Erase operation, the device continues to consume active power
until the Program or Erase operation is complete.
3.1.5
Reset
From read mode, RP# at VIL for time tPLPH deselects the memory, places output drivers in a highimpedance state, and turns off all internal circuits. After return from reset, a time tPHQV is required
until the initial read-access outputs are valid. A delay (tPHWL or tPHEL) is required after return from
reset before a write cycle can be initiated. After this wake-up interval, normal operation is restored.
The CUI resets to read-array mode, the status register is set to 0x80, and all blocks are locked. See
Figure 10, “Reset Operations Waveforms” on page 48.
If RP# is taken low for time tPLPH during a Program or Erase operation, the operation will be
aborted and the memory contents at the aborted location (for a program) or block (for an erase) are
no longer valid, since the data may be partially erased or written. The abort process goes through
the following sequence:
1. When RP# goes low, the device shuts down the operation in progress, a process which takes time
tPLRH to complete.
2. After time tPLRH, the part will either reset to read-array mode (if RP# is asserted during tPLRH) or
enter reset mode (if RP# is deasserted after tPLRH). See Figure 10, “Reset Operations Waveforms”
on page 48.
In both cases, after returning from an aborted operation, the relevant time tPHQV or tPHWL/tPHEL
must be observed before a Read or Write operation is initiated, as discussed in the previous
paragraph. However, in this case, these delays are referenced to the end of tPLRH rather than when
RP# goes high.
As with any automated device, it is important to assert RP# during a system reset. When the system
comes out of reset, the processor expects to read from the flash memory. Automated flash
memories provide status information when read during program or Block-Erase operations. If a
CPU reset occurs with no flash memory reset, proper CPU initialization may not occur because the
flash memory may be providing status information instead of array data. Intel® Flash memories
allow proper CPU initialization following a system reset through the use of the RP# input. In this
application, RP# is controlled by the same RESET# signal that resets the system CPU.
18
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
4.0
Modes of Operation
4.1
Read Mode
The flash memory has four read modes (read array, read identifier, read status, and CFI query), and
two write modes (program and erase). Three additional modes (erase suspend to program, erase
suspend to read, and program suspend to read) are available only during suspended operations.
Table 7, “Command Bus Operations” on page 24 and Table 8, “Command Codes and
Descriptions” on page 25 summarize the commands used to reach these modes. Appendix A,
“Write State Machine States” on page 50 is a comprehensive chart showing the state transitions.
4.1.1
Read Array
When RP# transitions from VIL (reset) to VIH, the device defaults to read-array mode and will
respond to the read-control inputs (CE#, address inputs, and OE#) without any additional CUI
commands.
When the device is in read array mode, four control signals control data output.
•
•
•
•
WE# must be logic high (VIH)
CE# must be logic low (VIL)
OE# must be logic low (VIL)
RP# must be logic high (VIH)
In addition, the address of the desired location must be applied to the address pins. If the device is
not in read-array mode, as would be the case after a Program or Erase operation, the Read Array
command (0xFF) must be issued to the CUI before array reads can occur.
4.1.2
Read Identifier
The read-identifier mode outputs three types of information: the manufacturer/device identifier, the
block locking status, and the protection register. The device is switched to this mode by issuing the
Read Identifier command (0x90). Once in this mode, read cycles from addresses shown in Table 6
retrieve the specified information. To return to read-array mode, issue the Read Array command
(0xFF).
Datasheet
19
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 6.
Device Identification Codes
Address1
Item
Manufacturer ID
Device ID
Data
Base
Offset
Block
0x00
Block
0x01
Block Lock Status2
Block
0x02
Block Lock-Down Status2
Block
0x02
Description
0x0089
0x88C0
8-Mbit Top Boot Device
0x88C1
8-Mbit Bottom Boot Device
0x88C2
16-Mbit Top Boot Device
0x88C3
16-Mbit Bottom Boot Device
0x88C4
32-Mbit Top Boot Device
0x88C5
32-Mbit Bottom Boot Device
0x88CC
64-Mbit Top Boot Device
0x88CD
64-Mbit Bottom Boot Device
DQ0 = 0b0
Block is unlocked
DQ0 = 0b1
Block is locked
DQ1 = 0b0
Block is not locked-down
DQ1 = 0b1
Block is locked down
Protection Register Lock Status
Block
0x80
Lock Data
Protection Register
Block
0x81 0x88
Register Data
Multiple reads required to read
the entire 128-bit Protection
Register.
NOTES:
1. The address is constructed from a base address plus an offset. For example, to read the Block Lock Status
for block number 38 in a bottom boot device, set the address to 0x0F8000 plus the offset (0x02), i.e.
0x0F8002. Then examine DQ0 of the data to determine if the block is locked.
2. See Section 5.2, “Reading Block-Lock Status” on page 28 for valid lock status.
4.1.3
CFI Query
The CFI query mode outputs Common Flash Interface (CFI) data after issuing the Read Query
Command (0x98). The CFI data structure contains information such as block size, density,
command set, and electrical specifications. Once in this mode, read cycles from addresses shown in
Appendix C, “Common Flash Interface,” retrieve the specified information. To return to read-array
mode, issue the Read Array command (0xFF).
4.1.4
Read Status Register
The status register indicates the status of device operations, and the success/failure of that
operation. The Read Status Register (0x70) command causes subsequent reads to output data from
the status register until another command is issued. To return to reading from the array, issue a
Read Array (0xFF) command.
The status-register bits are output on DQ[7:0]. The upper byte, DQ[15:8], outputs 0x00 when a
Read Status Register command is issued.
20
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
The contents of the status register are latched on the falling edge of OE# or CE# (whichever occurs
last) which prevents possible bus errors that might occur if Status Register contents change while
being read. CE# or OE# must be toggled with each subsequent status read, or the Status Register
will not indicate completion of a Program or Erase operation.
When the WSM is active, SR[7] will indicate the status of the WSM; the remaining bits in the
status register indicate whether the WSM was successful in performing the preferred operation (see
Table 9, “Status Register Bit Definition” on page 26).
4.1.4.1
Clear Status Register
The WSM can set Status Register bits 1 through 7 and can clear bits 2, 6, and 7; but, the WSM
cannot clear Status Register bits 1, 3, 4 or 5. Because bits 1, 3, 4, and 5 indicate various error
conditions, these bits can be cleared only through the Clear Status Register (0x50) command. By
allowing the system software to control the resetting of these bits, several operations may be
performed (such as cumulatively programming several addresses or erasing multiple blocks in
sequence) before reading the status register to determine if an error occurred during that series.
Clear the status register before beginning another command or sequence. The Read Array
command must be issued before data can be read from the memory array. Resetting the device also
clears the Status Register.
4.2
Program Mode
Programming is executed using a two-write cycle sequence. The Program Setup command (0x40)
is issued to the CUI followed by a second write which specifies the address and data to be
programmed. The WSM will execute a sequence of internally timed events to program preferred
bits of the addressed location, then verify the bits are sufficiently programmed. Programming the
memory results in specific bits within an address location being changed to a “0.” If users attempt
to program “1”s, the memory cell contents do not change and no error occurs.
The Status Register indicates programming status. While the program sequence executes, status bit
7 is “0.” The status register can be polled by toggling either CE# or OE#. While programming, the
only valid commands are Read Status Register, Program Suspend, and Program Resume.
When programming is complete, the program-status bits should be checked. If the programming
operation was unsuccessful, bit SR[4] of the Status Register is set to indicate a program failure. If
SR[3] is set, then VPP was not within acceptable limits, and the WSM did not execute the program
command. If SR[1] is set, a program operation was attempted on a locked block and the operation
was aborted.
The status register should be cleared before attempting the next operation. Any CUI instruction can
follow after programming is completed; however, to prevent inadvertent status-register reads, be
sure to reset the CUI to read-array mode.
4.2.1
12-Volt Production Programming
When VPP is between 1.65 V and 3.6 V, all program and erase current is drawn through the VCC
pin. Note that if VPP is driven by a logic signal, VIH min = 1.65 V. That is, VPP must remain above
1.65 V to perform in-system flash modifications. When VPP is connected to a 12 V power supply,
the device draws program and erase current directly from the VPP pin. This eliminates the need for
an external switching transistor to control VPP. Figure 7 on page 31 shows examples of how the
flash power supplies can be configured for various usage models.
Datasheet
21
Intel£ Advanced+ Boot Block Flash Memory (C3)
The 12 V VPP mode enhances programming performance during the short period of time typically
found in manufacturing processes; however, it is not intended for extended use. 12 V may be
applied to VPP during Program and Erase operations for a maximum of 1000 cycles on the main
blocks and 2500 cycles on the parameter blocks. VPP may be connected to 12 V for a total of 80
hours maximum. Stressing the device beyond these limits may cause permanent damage.
4.2.2
Suspending and Resuming Program
The Program Suspend command halts an in-progress program operation so that data can be read
from other locations of memory. Once the programming process starts, issuing the Program
Suspend command to the CUI requests that the WSM suspend the program sequence at
predetermined points in the program algorithm. The device continues to output status-register data
after the Program Suspend command is issued. Polling status-register bits SR[7] and SR[2] will
determine when the program operation has been suspended (both will be set to “1”). tWHRH1/
tEHRH1 specify the program-suspend latency.
A Read-Array command can now be issued to the CUI to read data from blocks other than that
which is suspended. The only other valid commands while program is suspended are Read Status
Register, Read Identifier, CFI Query, and Program Resume.
After the Program Resume command is issued to the flash memory, the WSM will continue with
the programming process and status register bits SR[2] and SR[7] will automatically be cleared.
The device automatically outputs status register data when read (see Figure 14, “Program Suspend
/ Resume Flowchart” on page 53) after the Program Resume command is issued. VPP must remain
at the same VPP level used for program while in program-suspend mode. RP# must also remain at
VIH.
4.3
Erase Mode
To erase a block, issue the Erase Set-up and Erase Confirm commands to the CUI, along with an
address identifying the block to be erased. This address is latched internally when the Erase
Confirm command is issued. Block erasure results in all bits within the block being set to “1.” Only
one block can be erased at a time. The WSM will execute a sequence of internally timed events to
program all bits within the block to “0,” erase all bits within the block to “1,” then verify that all
bits within the block are sufficiently erased. While the erase executes, status bit 7 is a “0.”
When the status register indicates that erasure is complete, check the erase-status bit to verify that
the Erase operation was successful. If the Erase operation was unsuccessful, SR[5] of the status
register will be set to a “1,” indicating an erase failure. If VPP was not within acceptable limits after
the Erase Confirm command was issued, the WSM will not execute the erase sequence; instead,
SR[5] of the status register is set to indicate an erase error, and SR[3] is set to a “1” to identify that
VPP supply voltage was not within acceptable limits.
After an Erase operation, clear the status register (0x50) before attempting the next operation. Any
CUI instruction can follow after erasure is completed; however, to prevent inadvertent statusregister reads, it is advisable to place the flash in read-array mode after the erase is complete.
22
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
4.3.1
Suspending and Resuming Erase
Since an Erase operation requires on the order of seconds to complete, an Erase Suspend command
is provided to allow erase-sequence interruption in order to read data from—or program data to—
another block in memory. Once the erase sequence is started, issuing the Erase Suspend command
to the CUI suspends the erase sequence at a predetermined point in the erase algorithm. The status
register will indicate if/when the Erase operation has been suspended. Erase-suspend latency is
specified by tWHRH2/tEHRH2.
A Read Array or Program command can now be issued to the CUI to read/program data from/to
blocks other than that which is suspended. This nested Program command can subsequently be
suspended to read yet another location. The only valid commands while Erase is suspended are
Read Status Register, Read Identifier, CFI Query, Program Setup, Program Resume, Erase
Resume, Lock Block, Unlock Block, and Lock-Down Block. During erase-suspend mode, the chip
can be placed in a pseudo-standby mode by taking CE# to VIH, which reduces active current
consumption.
Erase Resume continues the erase sequence when CE# = VIL. Similar to the end of a standard
Erase operation, the status register should be read and cleared before the next instruction is issued.
Datasheet
23
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 7.
Command Bus Operations
First Bus Cycle
Command
Second Bus Cycle
Notes
Oper
Addr
Data
Oper
Addr
Data
Read Array
1,3
Write
X
0xFF
Read Identifier
1,3
Write
X
0x90
Read
IA
ID
CFI Query
1,3
Write
X
0x98
Read
QA
QD
Read Status Register
1,3
Write
X
0x70
Read
X
SRD
Clear Status Register
1,3
Write
X
0x50
Program
2,3
Write
X
0x40/
0x10
Write
PA
PD
Block Erase/Confirm
1,3
Write
X
0x20
Write
BA
D0H
Program/Erase Suspend
1,3
Write
X
0xB0
Program/Erase Resume
1,3
Write
X
0xD0
Lock Block
1,3
Write
X
0x60
Write
BA
0x01
Unlock Block
1,3
Write
X
0x60
Write
BA
0xD0
Lock-Down Block
1,3
Write
X
0x60
Write
BA
0x2F
Protection Program
1,3
Write
X
0xC0
Write
PA
PD
X = "Don’t Care"
PA = Prog Addr
SRD = Status Reg.
Data
PD = Prog Data
BA = Block Addr
IA = Identifier Addr.
QA = Query Addr.
ID = Identifier Data
QD = Query Data
NOTES:
1. Following the Read Identifier or CFI Query commands, read operations output device identification data or
CFI query information, respectively. See Section 4.1.2 and Section 4.1.3.
2. Either 0x40 or 0x10 command is valid, but the Intel standard is 0x40.
3. When writing commands, the upper data bus [DQ8-DQ15] should be either VIL or VIH, to minimize current
draw.
Bus operations are defined in Table 5, “Bus Operations” on page 17.
24
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 8.
Command Codes and Descriptions
Code
(HEX)
Device Mode
FF
Read Array
Command Description
This command places the device in read-array mode, which outputs array data on the data
pins.
40
Program Set-Up
This is a two-cycle command. The first cycle prepares the CUI for a program operation. The
second cycle latches addresses and data information and initiates the WSM to execute the
Program algorithm. The flash outputs status-register data when CE# or OE# is toggled. A Read
Array command is required after programming to read array data. See Section 4.2, “Program
Mode” on page 21.
20
Erase Set-Up
This is a two-cycle command. Prepares the CUI for the Erase Confirm command. If the next
command is not an Erase Confirm command, then the CUI will (a) set both SR.4 and SR.5 of
the status register to a “1,” (b) place the device into the read-status-register mode, and (c) wait
for another command. See Section 4.3, “Erase Mode” on page 22.
Erase Confirm
If the previous command was an Erase Set-Up command, then the CUI will close the address
and data latches and begin erasing the block indicated on the address pins. During program/
erase, the device will respond only to the Read Status Register, Program Suspend and Erase
Suspend commands, and will output status-register data when CE# or OE# is toggled.
D0
Program/Erase
Resume
Unlock Block
If a Program or Erase operation was previously suspended, this command will resume that
operation.
If the previous command was Block Unlock Set-Up, the CUI will latch the address and unlock
the block indicated on the address pins. If the block had been previously set to Lock-Down, this
operation will have no effect. (See Section 5.1)
Issuing this command will begin to suspend the currently executing Program/Erase operation.
The status register will indicate when the operation has been successfully suspended by
setting either the program-suspend SR[2] or erase-suspend SR[6] and the WSM status bit
SR[7] to a “1” (ready). The WSM will continue to idle in the SUSPEND state, regardless of the
state of all input-control pins except RP#, which will immediately shut down the WSM and the
remainder of the chip if RP# is driven to VIL. See Sections 3.2.5.1 and 3.2.6.1.
B0
Program Suspend
Erase Suspend
70
Read Status
Register
This command places the device into read-status-register mode. Reading the device will
output the contents of the status register, regardless of the address presented to the device.
The device automatically enters this mode after a Program or Erase operation has been
initiated. See Section 4.1.4, “Read Status Register” on page 20.
50
Clear Status
Register
The WSM can set the block-lock status SR[1], VPP Status SR[3], program status SR[4], and
erase-status SR[5] bits in the status register to “1,” but it cannot clear them to “0.” Issuing this
command clears those bits to “0.”
90
Read
Identifier
60
Block Lock, Block
Unlock, Block
Lock-Down SetUp
Prepares the CUI for block-locking changes. If the next command is not Block Unlock, Block
Lock, or Block Lock-Down, then the CUI will set both the program and erase-status-register
bits to indicate a command-sequence error. See Section 5.0, “Security Modes” on page 27.
01
Lock-Block
If the previous command was Lock Set-Up, the CUI will latch the address and lock the block
indicated on the address pins. (See Section 5.1)
2F
Lock-Down
If the previous command was a Lock-Down Set-Up command, the CUI will latch the address
and lock-down the block indicated on the address pins. (See Section 5.1)
98
CFI
Query
Puts the device into the CFI-Query mode so that reading the device will output Common Flash
Interface information. See Section 4.1.3 and Appendix C, “Common Flash Interface”.
C0
Protection
Program
Set-Up
This is a two-cycle command. The first cycle prepares the CUI for a program operation to the
protection register. The second cycle latches addresses and data information and initiates the
WSM to execute the Protection Program algorithm to the protection register. The flash outputs
status-register data when CE# or OE# is toggled. A Read Array command is required after
programming to read array data. See Section 5.5.
Datasheet
Puts the device into the read-identifier mode so that reading the device will output the
manufacturer/device codes or block-lock status. See Section 4.1.2, “Read Identifier” on
page 19.
25
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 8.
Command Codes and Descriptions
Code
(HEX)
Device Mode
10
Alt. Prog Set-Up
00
Invalid/
Reserved
Command Description
Operates the same as Program Set-up command. (See 0x40/Program Set-Up)
Unassigned commands should not be used. Intel reserves the right to redefine these codes for
future functions.
NOTE: See Appendix A, “Write State Machine States” for mode transition information.
Table 9.
Status Register Bit Definition
WSMS
ESS
ES
PS
VPPS
PSS
BLS
R
7
6
5
4
3
2
1
0
NOTES:
SR[7] WRITE STATE MACHINE STATUS (WSMS)
1 = Ready
0 = Busy
Check Write State Machine bit first to determine Word Program
or Block Erase completion, before checking program or erasestatus bits.
SR[6] = ERASE-SUSPEND STATUS (ESS)
1 = Erase Suspended
0 = Erase In Progress/Completed
When Erase Suspend is issued, WSM halts execution and sets
both WSMS and ESS bits to “1.” ESS bit remains set to “1” until
an Erase Resume command is issued.
SR[5] = ERASE STATUS (ES)
1 = Error In Block Erase
0 = Successful Block Erase
When this bit is set to “1,” WSM has applied the max. number
of erase pulses to the block and is still unable to verify
successful block erasure.
SR[4] = PROGRAM STATUS (PS)
1 = Error in Programming
0 = Successful Programming
When this bit is set to “1,” WSM has attempted but failed to
program a word/byte.
SR[3] = VPP STATUS (VPPS)
1 = VPP Low Detect, Operation Abort
0 = VPP OK
The VPP status bit does not provide continuous indication of
VPP level. The WSM interrogates VPP level only after the
Program or Erase command sequences have been entered,
and informs the system if VPP has not been switched on. The
VPP is also checked before the operation is verified by the
WSM. The VPP status bit is not guaranteed to report accurate
feedback between VPPLK and VPP1Min.
SR[2] = PROGRAM SUSPEND STATUS (PSS)
1 = Program Suspended
0 = Program in Progress/Completed
When Program Suspend is issued, WSM halts execution and
sets both WSMS and PSS bits to “1.” PSS bit remains set to “1”
until a Program Resume command is issued.
SR[1] = BLOCK LOCK STATUS
1 = Prog/Erase attempted on a locked block; Operation
aborted.
0 = No operation to locked blocks
If a Program or Erase operation is attempted to one of the
locked blocks, this bit is set by the WSM. The operation
specified is aborted and the device is returned to read status
mode.
SR[0] = RESERVED FOR FUTURE ENHANCEMENTS (R)
This bit is reserved for future use and should be masked out
when polling the status register.
NOTE: A Command-Sequence Error is indicated when SR[4], SR[5], and SR[7] are set.
26
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
5.0
Security Modes
5.1
Flexible Block Locking
The C3 device offers an instant, individual block-locking scheme that allows any block to be
locked or unlocked with no latency, enabling instant code and data protection.
This locking scheme offers two levels of protection. The first level allows software-only control of
block locking (useful for data blocks that change frequently), while the second level requires
hardware interaction before locking can be changed (useful for code blocks that change
infrequently).
The following sections will discuss the operation of the locking system. The term “state [abc]” will
be used to specify locking states; e.g., “state [001],” where a = value of WP#, b = bit D1 of the
Block Lock status register, and c = bit D0 of the Block Lock status register. Figure 5, “Block
Locking State Diagram” on page 27 displays all of the possible locking states.
Figure 5. Block Locking State Diagram
Power-Up/Reset
Locked
[X01]
LockedDown4,5
[011]
Hardware
Locked5
[011]
WP# Hardware Control
Unlocked
[X00]
Software
Locked
[111]
Unlocked
[110]
Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0)
Software Block Lock-Down (0x60/0x2F)
WP# hardware control
Notes:
Datasheet
1. [a,b,c] represents [WP#, D1, D0]. X = Don’t Care.
2. D1 indicates block Lock-down status. D1 = ‘0’, Lock-down has not been issued to
this block. D1 = ‘1’, Lock-down has been issued to this block.
3. D0 indicates block lock status. D0 = ‘0’, block is unlocked. D0 = ‘1’, block is locked.
4. Locked-down = Hardware + Software locked.
5. [011] states should be tracked by system software to determine difference
between Hardware Locked and Locked-Down states.
27
Intel£ Advanced+ Boot Block Flash Memory (C3)
5.1.1
Locking Operation
The locking status of each block can be set to Locked, Unlocked, or Lock-Down, each of which
will be described in the following sections. See Figure 5, “Block Locking State Diagram” on
page 27 and Figure 17, “Locking Operations Flowchart” on page 56.
The following concisely summarizes the locking functionality.
5.1.1.1
Locked State
The default state of all blocks upon power-up or reset is locked (states [001] or [101]). Locked
blocks are fully protected from alteration. Any Program or Erase operations attempted on a locked
block will return an error on bit SR[1] of the Status Register. The state of a locked block can be
changed to Unlocked or Lock Down using the appropriate software commands. An Unlocked
block can be locked by writing the Lock command sequence, 0x60 followed by 0x01.
5.1.1.2
Unlocked State
Unlocked blocks (states [000], [100], [110]) can be programmed or erased. All unlocked blocks
return to the Locked state when the device is reset or powered down. The status of an unlocked
block can be changed to Locked or Locked Down using the appropriate software commands. A
Locked block can be unlocked by writing the Unlock command sequence, 0x60 followed by 0xD0.
5.1.1.3
Lock-Down State
Blocks that are Locked-Down (state [011]) are protected from Program and Erase operations (just
like Locked blocks), but their protection status cannot be changed using software commands alone.
A Locked or Unlocked block can be Locked Down by writing the Lock-Down command sequence,
0x60 followed by 0x2F. Locked-Down blocks revert to the Locked state when the device is reset or
powered down.
The Lock-Down function depends on the WP# input pin. When WP# = 0, blocks in Lock Down
[011] are protected from program, erase, and lock status changes. When WP# = 1, the Lock-Down
function is disabled ([111]) and Locked-Down blocks can be individually unlocked by software
command to the [110] state, where they can be erased and programmed. These blocks can then be
relocked [111] and unlocked [110] as required while WP# remains high. When WP# goes low,
blocks that were previously Locked Down return to the Lock-Down state [011], regardless of any
changes made while WP# was high. Device reset or power-down resets all blocks, including those
in Lock-Down, to Locked state.
5.2
Reading Block-Lock Status
The Lock status of each block can be read in read-identifier mode of the device by issuing the readidentifier command (0x90). Subsequent reads at Block Address + 0x00002 will output the Lock
status of that block. The Lock status is represented by DQ0 and DQ1. DQ0 indicates the Block
Lock/Unlock status and is set by the Lock command and cleared by the Unlock command. It is also
automatically set when entering Lock Down. DQ1 indicates Lock-Down status, and is set by the
Lock-Down command. It cannot be cleared by software—only by device reset or power-down. See
Table 6, “Device Identification Codes” on page 20 for block-status information.
28
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
5.3
Locking Operations during Erase Suspend
Changes to block-lock status can be performed during an erase-suspend by using the standard
locking command sequences to Unlock, Lock, or Lock Down a block. This is useful in the case
when another block needs to be updated while an Erase operation is in progress.
To change block locking during an Erase operation, first issue the Erase Suspend command (0xB0),
then check the status register until it indicates that the Erase operation has been suspended. Next,
write the preferred Lock command sequence to a block and the Lock status will be changed. After
completing any preferred Lock, Read, or Program operations, resume the Erase operation with the
Erase Resume command (0xD0).
If a block is Locked or Locked Down during a Suspended Erase of the same block, the locking
status bits will be changed immediately. But when the Erase is resumed, the Erase operation will
complete.
Locking operations cannot be performed during a Program Suspend. Refer to Appendix A, “Write
State Machine States” on page 50 for detailed information on which commands are valid during
Erase Suspend.
5.4
Status Register Error Checking
Using nested-locking or program-command sequences during Erase Suspend can introduce
ambiguity into status register results.
Since locking changes are performed using a two-cycle command sequence, e.g., 0x60 followed by
0x01 to lock a block, following the Block Lock, Block Unlock, or Block Lock-Down Setup
command (0x60) with an invalid command will produce a Lock-Command error (SR[4] and SR[5]
will be set to 1) in the Status Register. If a Lock-Command error occurs during an Erase Suspend,
SR[4] and SR[5] will be set to 1 and will remain at 1 after the Erase is resumed. When Erase is
complete, any possible error during the Erase cannot be detected via the status register because of
the previous Lock-Command error.
A similar situation happens if an error occurs during a Program-Operation error nested within an
Erase Suspend.
5.5
128-Bit Protection Register
The C3 device architecture includes a 128-bit protection register than can be used to increase the
security of a system design. For example, the number contained in the protection register can be
used to “match” the flash component with other system components, such as the CPU or ASIC,
preventing device substitution. The Intel application note, AP-657 Designing with the Advanced+
Boot Block Flash Memory Architecture, contains additional application information.
The 128 bits of the protection register are divided into two 64-bit segments. One of the segments is
programmed at the Intel factory with a unique 64-bit number, which is unchangeable. The other
segment is left blank for customer designs to program, as preferred. Once the customer segment is
programmed, it can be locked to prevent further programming.
Datasheet
29
Intel£ Advanced+ Boot Block Flash Memory (C3)
5.5.1
Reading the Protection Register
The protection register is read in the read-identifier mode. The device is switched to this mode by
issuing the Read Identifier command (0x90). Once in this mode, read cycles from addresses shown
in Figure 6, “Protection Register Mapping” retrieve the specified information. To return to readarray mode, issue the Read Array command (0xFF).
5.5.2
Programming the Protection Register
The protection register bits are programmed using the two-cycle Protection Program command.
The 64-bit number is programmed 16 bits at a time. First, issue the Protection Program Setup
command, 0xC0. The next write to the device will latch in address and data, and program the
specified location. The allowable addresses are shown in Table 6, “Device Identification Codes” on
page 20. See Figure 18, “Protection Register Programming Flowchart” on page 57. Attempts to
address Protection Program commands outside the defined protection register address space should
not be attempted. Attempting to program to a previously locked protection register segment will
result in a Status Register error (Program Error bit SR[4] and Lock Error bit SR[1] will be set to 1).
5.5.3
Locking the Protection Register
The user-programmable segment of the protection register is lockable by programming bit 1 of the
PR-LOCK location to 0. See Figure 6, “Protection Register Mapping” on page 30. Bit 0 of this
location is programmed to 0 at the Intel factory to protect the unique device number. This bit is set
using the Protection Program command to program 0xFFFD to the PR-LOCK location. After these
bits have been programmed, no further changes can be made to the values stored in the protection
register. Protection Program commands to a locked section will result in a Status Register error
(Program Error bit SR[4] and Lock Error bit SR[1] will be set to 1). Protection register lockout
state is not reversible.
Figure 6. Protection Register Mapping
0x88
64-bit Segment
(User-Programmable)
0x85
0x84
128-Bit Protection Register 0
64-bit Segment
(Intel Factory-Programmed)
0x81
PR Lock Register 0
0x80
5.6
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
VPP Program and Erase Voltages
The C3 device provides in-system programming and erase in the 1.65 V–3.6 V range. For fast
production programming, 12 V programming can be used. Refer to Figure 7, “Example Power
Supply Configurations” on page 31.
30
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
5.6.1
Program Protection
In addition to the flexible block locking, the VPP programming voltage can be held low for absolute
hardware write protection of all blocks in the flash device. When VPP is below or equal to VPPLK,
any Program or Erase operation will result in an error, prompting the corresponding status-register
bit (SR[3]) to be set.
Figure 7. Example Power Supply Configurations
System Supply
System Supply
12 V Supply
10 ≤ KΩ
VPP
12 V Fast Programming
Absolute Write Protection With V
VCC
VCC
Prot#
(Logic Signal)
VPP
Low-Voltage Programming
≤ V PPLK
PP
System Supply
Absolute Write Protection via Logic Signal
System Supply
VCC
VCC
VPP
VPP
Low Voltage and 12 V Fast Programming
Low-Voltage Programming
(Note 1)
12 V Supply
0645_06
NOTE:
1. A resistor can be used if the VCC supply can sink adequate current based on resistor value. See AP-657
Designing with the Advanced+ Boot Block Flash Memory Architecture for details.
Datasheet
31
Intel£ Advanced+ Boot Block Flash Memory (C3)
6.0
Power Consumption
Intel Flash devices have a tiered approach to power savings that can significantly reduce overall
system power consumption. The Automatic Power Savings (APS) feature reduces power
consumption when the device is selected but idle. If CE# is deasserted, the flash enters its standby
mode, where current consumption is even lower. If RP# is deasserted, the flash enter deep powerdown mode for ultra-low current consumption. The combination of these features can minimize
memory power consumption, and therefore, overall system power consumption.
6.1
Active Power (Program/Erase/Read)
With CE# at a logic-low level and RP# at a logic-high level, the device is in the active mode. Refer
to the DC Characteristic tables for ICC current values. Active power is the largest contributor to
overall system power consumption. Minimizing the active current could have a profound effect on
system power consumption, especially for battery-operated devices.
6.2
Automatic Power Savings (APS)
Automatic Power Savings provides low-power operation during read mode. After data is read from
the memory array and the address lines are idle, APS circuitry places the device in a mode where
typical current is comparable to ICCS. The flash stays in this static state with outputs valid until a
new location is read.
6.3
Standby Power
When CE# is at a logic-high level (VIH), the flash memory is in standby mode, which disables
much of the device’s circuitry and substantially reduces power consumption. Outputs are placed in
a high-impedance state independent of the status of the OE# signal. If CE# transitions to a logichigh level during Erase or Program operations, the device will continue to perform the operation
and consume corresponding active power until the operation is completed.
System engineers should analyze the breakdown of standby time versus active time, and quantify
the respective power consumption in each mode for their specific application. This approach will
provide a more accurate measure of application-specific power and energy requirements.
6.4
Deep Power-Down Mode
The deep power-down mode is activated when RP# = VIL. During read modes, RP# going low deselects the memory and places the outputs in a high-impedance state. Recovery from deep powerdown requires a minimum time of tPHQV for Read operations, and tPHWL/tPHEL for Write
operations.
32
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
During program or erase modes, RP# transitioning low will abort the in-progress operation. The
memory contents of the address being programmed or the block being erased are no longer valid as
the data integrity has been compromised by the abort. During deep power-down, all internal
circuits are switched to a low-power savings mode (RP# transitioning to VIL or turning off power
to the device clears the status register).
6.5
Power and Reset Considerations
6.5.1
Power-Up/Down Characteristics
In order to prevent any condition that may result in a spurious write or erase operation, it is
recommended to power-up VCC and VCCQ together. Conversely, VCC and VCCQ must powerdown together.
It is also recommended to power-up VPP with or after VCC has reached VCCmin. Conversely, VPP
must powerdown with or slightly before VCC.
If VCCQ and/or VPP are not connected to the VCC supply, then VCC should attain VCCmin before
applying VCCQ and VPP. Device inputs should not be driven before supply voltage reaches
VCCmin.
Power supply transitions should only occur when RP# is low.
6.5.2
RP# Connected to System Reset
The use of RP# during system reset is important with automated program/erase devices since the
system expects to read from the flash memory when it comes out of reset. If a CPU reset occurs
without a flash memory reset, proper CPU initialization will not occur because the flash memory
may be providing status information instead of array data. Intel recommends connecting RP# to the
system CPU RESET# signal to allow proper CPU/flash initialization following system reset.
System designers must guard against spurious writes when VCC voltages are above VLKO. Because
both WE# and CE# must be low for a command write, driving either signal to VIH will inhibit
writes to the device. The CUI architecture provides additional protection since alteration of
memory contents can only occur after successful completion of the two-step command sequences.
The device is also disabled until RP# is brought to VIH, regardless of the state of its control inputs.
By holding the device in reset during power-up/down, invalid bus conditions during power-up can
be masked, providing yet another level of memory protection.
6.5.3
VCC, VPP and RP# Transitions
The CUI latches commands as issued by system software and is not altered by VPP or CE#
transitions or WSM actions. Its default state upon power-up, after exit from reset mode or after
VCC transitions above VLKO (Lockout voltage), is read-array mode.
After any program or Block-Erase operation is complete (even after VPP transitions down to
VPPLK), the CUI must be reset to read-array mode via the Read Array command if access to the
flash-memory array is desired.
Datasheet
33
Intel£ Advanced+ Boot Block Flash Memory (C3)
6.6
Power Supply Decoupling
Flash memory power-switching characteristics require careful device decoupling. System
designers should consider the following three supply current issues:
• Standby current levels (ICCS)
• Read current levels (ICCR)
• Transient peaks produced by falling and rising edges of CE#.
Transient current magnitudes depend on the device outputs’ capacitive and inductive loading. Twoline control and proper decoupling capacitor selection will suppress these transient voltage peaks.
Each flash device should have a 0.1 µF ceramic capacitor connected between each VCC and GND,
and between its VPP and VSS. These high- frequency, inherently low-inductance capacitors should
be placed as close as possible to the package leads.
7.0
Thermal and DC Characteristics
7.1
Absolute Maximum Ratings
Warning:
Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent damage.
These are stress ratings only. Operation beyond the “Operating Conditions” is not recommended,
and extended exposure beyond the “Operating Conditions” may affect device reliability.
.
NOTICE: Specifications are subject to change without notice. Verify with your local Intel Sales office that you have
the latest datasheet before finalizing a design.
Parameter
Maximum Rating
Notes
Extended Operating Temperature
During Read
–40 °C to +85 °C
During Block Erase and Program
–40 °C to +85 °C
Temperature under Bias
–40 °C to +85 °C
Storage Temperature
–65 °C to +125 °C
Voltage On Any Pin (except VCC and VPP) with Respect to GND
–0.5 V to +3.7 V
1
VPP Voltage (for Block Erase and Program) with Respect to GND
–0.5 V to +13.5 V
1,2,3
VCC and VCCQ Supply Voltage with Respect to GND
–0.2 V to +3.6 V
Output Short Circuit Current
100 mA
4
NOTES:
1. Minimum DC voltage is –0.5 V on input/output pins. During transitions, this level may
undershoot to –2.0 V for periods <20 ns. Maximum DC voltage on input/output pins is VCC
+0.5 V which, during transitions, may overshoot to VCC +2.0 V for periods <20 ns.
2. Maximum DC voltage on VPP may overshoot to +14.0 V for periods <20 ns.
3. VPP Program voltage is normally 1.65 V–3.6 V. Connection to a 11.4 V–12.6 V supply can be
done for a maximum of 1000 cycles on the main blocks and 2500 cycles on the parameter
blocks during program/erase. VPP may be connected to 12 V for a total of 80 hours maximum.
4. Output shorted for no more than one second. No more than one output shorted at a time.
34
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
7.2
Operating Conditions
Table 10. Temperature and Voltage Operating Conditions
Symbol
Parameter
TA
Operating Temperature
VCC1
VCC Supply Voltage
Notes
VCC2
VCCQ1
VCCQ2
VPP2
Cycling
Block Erase Cycling
Units
–40
+85
°C
2.7
3.6
Volts
1, 2
3.0
3.6
1
2.7
3.6
I/O Supply Voltage
Supply Voltage
Max
1, 2
1.65
2.5
1.8
2.5
1
1.65
3.6
Volts
1, 3
11.4
12.6
Volts
3
100,000
VCCQ3
VPP1
Min
Volts
Cycles
NOTES:
1. VCC and VCCQ must share the same supply when they are in the VCC1 range.
2. VCCMax = 3.3 V for 0.25µm 32-Mbit devices.
3. Applying VPP = 11.4 V–12.6 V during a program/erase can only be done for a maximum of 1000 cycles on
the main blocks and 2500 cycles on the parameter blocks. VPP may be connected to 12 V for a total of
80 hours maximum.
7.3
DC Current Characteristics
Table 11. DC Current Characteristics (Sheet 1 of 3)
Sym
ILI
ILO
Datasheet
Parameter
Input Load Current
Output Leakage
Current
VCC
2.7 V–3.6 V
2.7 V–2.85 V
2.7 V–3.3 V
VCCQ
2.7 V–3.6 V
1.65 V–2.5 V
1.8 V–2.5 V
Note
Typ
Typ
Typ
1,2
1,2
Max
±1
± 10
Max
±1
± 10
Unit
Test
Conditions
µA
VCC =
VCCMax
VCCQ =
VCCQMax
VIN = VCCQ
or GND
µA
VCC =
VCCMax
VCCQ =
VCCQMax
VIN = VCCQ
or GND
Max
±1
± 10
35
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 11. DC Current Characteristics (Sheet 2 of 3)
Sym
ICCS
ICCD
VCC
2.7 V–3.6 V
2.7 V–2.85 V
2.7 V–3.3 V
VCCQ
2.7 V–3.6 V
1.65 V–2.5 V
1.8 V–2.5 V
Note
Typ
Max
Typ
Max
Typ
Max
VCC Standby Current
for 0.13 and 0.18
Micron Product
1
7
15
20
50
150
250
µA
VCC Standby Current
for 0.25 Micron
Product
1
10
25
20
50
150
250
µA
VCC Power-Down
Current for 0.13 and
0.18 Micron Product
1,2
7
15
7
20
7
20
µA
VCC Power-Down
Current for 0.25
Product
1,2
7
25
7
25
7
25
µA
VCC Read Current for
0.13 and 0.18 Micron
Product
1,2,3
9
18
8
15
9
15
mA
VCC Read Current for
0.25 Micron Product
1,2,3
10
18
8
15
9
15
mA
1
0.2
5
0.2
5
0.2
5
µA
RP# = GND
± 0.2 V
VPP ≤ VCC
18
55
18
55
18
55
mA
VPP =VPP1,
Program in
Progress
8
22
10
30
10
30
mA
16
45
21
45
21
45
mA
8
15
16
45
16
45
mA
7
15
50
200
50
200
µA
10
25
50
200
50
200
µA
Parameter
Unit
ICCW
ICCE
ICCES/
ICCWS
36
VPP Deep PowerDown Current
VCC Program Current
VCC Erase Current
VCC Erase Suspend
Current for 0.13 and
0.18 Micron Product
VCC Erase Suspend
Current for 0.25
Micron Product
VCC =
VCCMax
CE# = RP#
= VCCQ
or during
Program/
Erase
Suspend
WP# =
VCCQ or
GND
ICCR
IPPD
Test
Conditions
1,4
VCC =
VCCMax
VCCQ =
VCCQMax
VIN = VCCQ
or GND
RP# = GND
± 0.2 V
VCC =
VCCMax
VCCQ =
VCCQMax
OE# = VIH,
CE# =VIL
f = 5 MHz,
IOUT=0 mA
Inputs = VIL
or VIH
VPP = VPP2
1,4
1,4,5
(12v)
Program in
Progress
VPP = VPP1,
Erase in
Progress
VPP =
(12v) ,
VPP2
Erase in
Progress
CE# = VIH,
Erase
Suspend in
Progress
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 11. DC Current Characteristics (Sheet 3 of 3)
Sym
IPPR
IPPW
IPPE
Parameter
VPP Read Current
VPP Program Current
VPP Erase Current
VCC
2.7 V–3.6 V
2.7 V–2.85 V
2.7 V–3.3 V
VCCQ
2.7 V–3.6 V
1.65 V–2.5 V
1.8 V–2.5 V
Note
Typ
Max
Typ
Max
Typ
Max
2
±15
2
±15
2
±15
µA
VPP ≤ VCC
50
200
50
200
50
200
µA
VPP > VCC
0.05
0.1
0.05
0.1
0.05
0.1
mA
VPP =VPP1,
Program in
Progress
8
22
8
22
8
22
mA
0.05
0.1
0.05
0.1
0.05
0.1
mA
8
22
16
45
16
45
mA
1,4
1,4
1,4
VCC Erase Suspend
Current
Test
Conditions
VPP =
(12v)
VPP2
Program in
Progress
VPP = VPP1,
Erase in
Progress
VPP = VPP2
0.2
IPPES/
IPPWS
Unit
5
0.2
5
0.2
5
µA
1,4
(12v) ,
Erase in
Progress
VPP = VPP1,
Program or
Erase
Suspend in
Progress
VPP = VPP2
(12v) ,
50
200
50
200
50
200
µA
Program or
Erase
Suspend in
Progress
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at nominal VCC, TA = +25 °C.
2. The test conditions VCCMax, VCCQMax, VCCMin, and VCCQMin refer to the maximum or minimum VCC or
VCCQ voltage listed at the top of each column. VCCMax = 3.3 V for 0.25µm 32-Mbit devices.
3. Automatic Power Savings (APS) reduces ICCR to approximately standby levels in static operation (CMOS
inputs).
4. Sampled, not 100% tested.
5. ICCES or ICCWS is specified with device de-selected. If device is read while in erase suspend, current draw
is sum of ICCES and ICCR. If the device is read while in program suspend, current draw is the sum of ICCWS
and ICCR.
Datasheet
37
Intel£ Advanced+ Boot Block Flash Memory (C3)
7.4
DC Voltage Characteristics
Table 12. DC Voltage Characteristics
Sym
Parameter
VCC
2.7 V–3.6 V
2.7 V–2.85 V
2.7 V–3.3 V
VCCQ
2.7 V–3.6 V
1.65 V–2.5 V
1.8 V–2.5 V
Note
Min
Max
Min
Max
Min
Max
Unit
Test Conditions
VIL
Input Low
Voltage
–0.4
VCC *
0.22 V
–0.4
0.4
–0.4
0.4
V
VIH
Input High
Voltage
2.0
VCCQ
+0.3V
VCCQ –
0.4V
VCCQ
+0.3V
VCCQ –
0.4V
VCCQ
+0.3V
V
VOL
Output Low
Voltage
–0.1
0.1
-0.1
0.1
-0.1
0.1
V
VCC = VCCMin
VCCQ = VCCQMin
IOL = 100 µA
VOH
Output High
Voltage
VCCQ
–0.1V
V
VCC = VCCMin
VCCQ = VCCQMin
IOH = –100 µA
VPPLK
VPP LockOut Voltage
1.0
V
Complete Write
Protection
VPP1
VPP2
VPP during
Program /
Erase
Operations
1
VCCQ –
0.1V
1.0
VCCQ –
0.1V
1.0
1
1.65
3.6
1.65
3.6
1.65
3.6
V
1,2
11.4
12.6
11.4
12.6
11.4
12.6
V
VLKO
VCC Prog/
Erase
Lock
Voltage
1.5
1.5
1.5
V
VLKO2
VCCQ Prog/
Erase
Lock
Voltage
1.2
1.2
1.2
V
NOTES:
1. Erase and Program are inhibited when VPP < VPPLK and not guaranteed outside the valid VPP ranges of VPP1 and VPP2.
2. Applying VPP = 11.4 V–12.6 V during program/erase can only be done for a maximum of 1000 cycles on the main blocks and
2500 cycles on the parameter blocks. VPP may be connected to 12 V for a total of 80 hours maximum.
38
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
8.0
AC Characteristics
8.1
AC Read Characteristics
Table 13. Read Operations—8 Mbit Density
Density
8 Mbit
Product
#
Sym
90 ns
110 ns
Parameter
Unit
3.0 V – 3.6 V
2.7 V – 3.6 V
3.0 V – 3.6 V
2.7 V – 3.6 V
Note
Min
Min
Min
Min
80
VCC
Max
Max
tAVAV
Read Cycle Time
3,4
R2
tAVQV
Address to Output Delay
3,4
80
90
100
110
ns
R3
tELQV
CE# to Output Delay
1,3,4
80
90
100
110
ns
R4
tGLQV
OE# to Output Delay
1,3,4
30
30
30
30
ns
R5
tPHQV
RP# to Output Delay
3,4
150
150
150
150
ns
R6
tELQX
CE# to Output in Low Z
2,3,4
0
0
0
0
ns
R7
tGLQX
OE# to Output in Low Z
2,3,4
0
0
0
0
ns
R8
tEHQZ
CE# to Output in High Z
2,3,4
20
20
20
20
ns
R9
tGHQZ
OE# to Output in High Z
2,3,4
20
20
20
20
ns
tOH
Output Hold from
Address, CE#, or OE#
Change, Whichever
Occurs First
2,3,4
0
0
100
Max
R1
R10
90
Max
0
110
0
ns
ns
NOTES:
1. OE# may be delayed up to tELQV–tGLQV after the falling edge of CE# without impact on tELQV.
2. Sampled, but not 100% tested.
3. See Figure 8, “Read Operation Waveform” on page 42.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and maximum allowable input
slew rate.
Datasheet
39
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 14. Read Operations—16 Mbit Density
Density
#
Sym
Paramete
r
16 Mbit
Product
70 ns
80 ns
VCC
2.7 V–3.6 V
2.7 V–3.6 V
3.0 V–3.6 V
2.7 V–3.6 V
3.0 V–3.6V
2.7 V–3.6V
Min
Min
Min
Min
Min
Min
Max
70
Max
80
90 ns
Max
80
110 ns
Max
90
Max
100
Unit
Notes
ns
3,4
Max
110
R1
tAVAV
Read Cycle Time
R2
tAVQ
Address to
Output Delay
70
80
80
90
100
110
ns
3,4
R3
tELQ
CE# to Output
Delay
70
80
80
90
100
110
ns
1,3,4
R4
tGLQ
OE# to Output
Delay
20
20
30
30
30
30
ns
1,3,4
R5
tPHQ
RP# to Output
Delay
150
150
150
150
150
150
ns
3,4
R6
tELQ
R7
tGLQ
R8
tEHQ
R9
tGHQ
R10
tOH
V
V
V
V
X
X
Z
Z
CE# to Output in
Low Z
0
0
0
0
0
0
ns
2,3,4
OE# to Output in
Low Z
0
0
0
0
0
0
ns
2,3,4
CE# to Output in
High Z
20
20
20
20
20
20
ns
2,3,4
OE# to Output in
High Z
20
20
20
20
20
20
ns
2,3,4
ns
2,3,4
Output Hold from
Address, CE#, or
OE# Change,
Whichever
Occurs First
0
0
0
0
0
0
NOTES:
1. OE# may be delayed up to tELQV–tGLQV after the falling edge of CE# without impact on tELQV.
2. Sampled, but not 100% tested.
3. See Figure 8, “Read Operation Waveform” on page 42.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and maximum allowable input
slew rate.
40
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 15. Read Operations—32 Mbit Density
Density
#
Sym
Parameter
32 Mbit
Product
70 ns
90 ns
VCC
2.7 V–3.6 V
2.7 V–3.6 V
3.0 V–3.3 V
2.7 V–3.3 V
3.0 V–3.3 V
2.7 V–3.3 V
Min
Min
Min
Min
Min
Min
Max
70
Max
90
100 ns
Max
90
110 ns
Max
100
Max
100
Unit
Notes
ns
3,4
Max
110
R1
tAVAV
Read Cycle Time
R2
tAVQ
Address to Output
Delay
70
90
90
100
100
110
ns
3,4
R3
tELQ
CE# to Output
Delay
70
90
90
100
100
110
ns
1,3,4
R4
tGLQ
OE# to Output
Delay
20
20
30
30
30
30
ns
1,3,4
R5
tPHQ
RP# to Output
Delay
150
150
150
150
150
150
ns
3,4
R6
tELQ
R7
tGLQ
R8
tEHQ
R9
tGHQ
R10
tOH
V
V
V
V
X
X
Z
Z
CE# to Output in
Low Z
0
0
0
0
0
0
ns
2,3,4
OE# to Output in
Low Z
0
0
0
0
0
0
ns
2,3,4
CE# to Output in
High Z
20
20
20
20
20
20
ns
2,3,4
OE# to Output in
High Z
20
20
20
20
20
20
ns
2,3,4
ns
2,3,4
Output Hold from
Address, CE#, or
OE# Change,
Whichever
Occurs First
0
0
0
0
0
0
NOTES:
1. OE# may be delayed up to tELQV–tGLQV after the falling edge of CE# without impact on tELQV.
2. Sampled, but not 100% tested.
3. See Figure 8, “Read Operation Waveform” on page 42.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and maximum allowable
input slew rate.
Datasheet
41
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 16. Read Operations — 64 Mbit Density
Density
#
Sym
64 Mbit
Product
70 ns
80 ns
VCC
2.7 V–3.6 V
2.7 V–3.6 V
Note
Min
Min
70
Parameter
Unit
Max
Max
R1
tAVAV
Read Cycle Time
3,4
R2
tAVQV
Address to Output Delay
3,4
70
80
ns
R3
tELQV
CE# to Output Delay
1,3,4
70
80
ns
R4
tGLQV
OE# to Output Delay
1,3,4
20
20
ns
R5
tPHQV
RP# to Output Delay
3,4
150
150
ns
R6
tELQX
CE# to Output in Low Z
R7
tGLQX
R8
tEHQZ
R9
tGHQZ
R10
tOH
80
ns
2,3,4
0
OE# to Output in Low Z
2,3,4
0
CE# to Output in High Z
2,3,4
20
20
ns
OE# to Output in High Z
2,3,4
20
20
ns
Output Hold from Address, CE#, or OE#
Change, Whichever Occurs First
2,3,4
0
0
ns
0
ns
0
ns
NOTES:
1. OE# may be delayed up to tELQV–tGLQV after the falling edge of CE# without impact on tELQV.
2. Sampled, but not 100% tested.
3. See Figure 8, “Read Operation Waveform” on page 42.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and
maximum allowable input slew rate.
Figure 8. Read Operation Waveform
R1
R2
Address [A]
R3
R8
CE# [E]
R4
R9
OE# [G]
WE# [W]
R7
R6
R10
Data [D/Q]
R5
RST# [P]
42
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
8.2
AC Write Characteristics
Table 17. Write Operations—8 Mbit Density
Density
8 Mbit
Product
#
Sym
Parameter
90 ns
3.0 V – 3.6 V
110 ns
80
100
Unit
VCC
2.7 V – 3.6 V
90
110
Note
Min
Min
Min
Min
W1
tPHWL /
tPHEL
RP# High Recovery to WE# (CE#) Going Low
4,5
150
150
150
150
ns
W2
tELWL /
tWLEL
CE# (WE#) Setup to WE# (CE#) Going Low
4,5
0
0
0
0
ns
W3
tWLWH /
tELEH
WE# (CE#) Pulse Width
4,5
50
60
70
70
ns
W4
tDVWH /
tDVEH
Data Setup to WE# (CE#) Going High
2,4,5
50
50
60
60
ns
W5
tAVWH /
tAVEH
Address Setup to WE# (CE#) Going High
2,4,5
50
60
70
70
ns
W6
tWHEH /
tEHWH
CE# (WE#) Hold Time from WE# (CE#) High
4,5
0
0
0
0
ns
W7
tWHDX /
tEHDX
Data Hold Time from WE# (CE#) High
2,4,5
0
0
0
0
ns
W8
tWHAX /
tEHAX
Address Hold Time from WE# (CE#) High
2,4,5
0
0
0
0
ns
W9
tWHWL /
tEHEL
WE# (CE#) Pulse Width High
2,4,5
30
30
30
30
ns
W10
tVPWH /
tVPEH
VPP Setup to WE# (CE#) Going High
3,4,5
200
200
200
200
ns
W11
tQVVL
VPP Hold from Valid SRD
3,4
0
0
0
0
ns
W12
tBHWH /
tBHEH
WP# Setup to WE# (CE#) Going High
3,4
0
0
0
0
ns
W13
tQVBL
WP# Hold from Valid SRD
3,4
0
0
0
0
ns
W14
tWHGL
WE# High to OE# Going Low
3,4
30
30
30
30
ns
NOTES:
1. Write pulse width (tWP) is defined from CE# or WE# going low (whichever goes low last) to CE# or WE# going high (whichever
goes high first). Hence, tWP = tWLWH = tELEH = tWLEH = tELWH. Similarly, write pulse width high (tWPH) is defined from CE# or
WE# going high (whichever goes high first) to CE# or WE# going low (whichever goes low last). Hence,
tWPH = tWHWL = tEHEL = tWHEL = tEHWL.
2. Refer to Table 7, “Command Bus Operations” on page 24 for valid AIN or DIN.
3. Sampled, but not 100% tested.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and maximum allowable input
slew rate.
5. See Figure 9, “Write Operations Waveform” on page 47.
Datasheet
43
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 18. Write Operations—16 Mbit Density
Density
16 Mbit
Product
#
Sym
Parameter
70 ns
80 ns
3.0 V – 3.6 V
90 ns
110 ns
80
100
Unit
VCC
2.7 V – 3.6 V
70
80
90
110
Note
Min
Min
Min
Min
Min
Min
W1
tPHWL /
tPHEL
RP# High Recovery to WE# (CE#) Going
Low
4,5
150
150
150
150
150
150
ns
W2
tELWL /
tWLEL
CE# (WE#) Setup to WE# (CE#) Going Low
4,5
0
0
0
0
0
0
ns
W3
tWLWH /
tELEH
WE# (CE#) Pulse Width
1,4,5
45
50
50
60
70
70
ns
W4
tDVWH /
tDVEH
Data Setup to WE# (CE#) Going High
2,4,5
40
40
50
50
60
60
ns
W5
tAVWH /
tAVEH
Address Setup to WE# (CE#) Going High
2,4,5
50
50
50
60
70
70
ns
W6
tWHEH /
tEHWH
CE# (WE#) Hold Time from WE# (CE#)
High
4,5
0
0
0
0
0
0
ns
W7
tWHDX /
tEHDX
Data Hold Time from WE# (CE#) High
2,4,5
0
0
0
0
0
0
ns
W8
tWHAX /
tEHAX
Address Hold Time from WE# (CE#) High
2,4,5
0
0
0
0
0
0
ns
W9
tWHWL /
tEHEL
WE# (CE#) Pulse Width High
1,4,5
25
30
30
30
30
30
ns
W10
tVPWH /
tVPEH
VPP Setup to WE# (CE#) Going High
3,4,5
200
200
200
200
200
200
ns
W11
tQVVL
VPP Hold from Valid SRD
3,4
0
0
0
0
0
0
ns
W12
tBHWH /
tBHEH
WP# Setup to WE# (CE#) Going High
3,4
0
0
0
0
0
0
ns
W13
tQVBL
WP# Hold from Valid SRD
3,4
0
0
0
0
0
0
ns
W14
tWHGL
WE# High to OE# Going Low
3,4
30
30
30
30
30
30
ns
NOTES:
1. Write pulse width (tWP) is defined from CE# or WE# going low (whichever goes low last) to CE# or WE# going high
(whichever goes high first). Hence, tWP = tWLWH = tELEH = tWLEH = tELWH. Similarly, write pulse width high (tWPH) is defined
from CE# or WE# going high (whichever goes high first) to CE# or WE# going low (whichever goes low last). Hence,
tWPH = tWHWL = tEHEL = tWHEL = tEHWL.
2. Refer to Table 7, “Command Bus Operations” on page 24 for valid AIN or DIN.
3. Sampled, but not 100% tested.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and maximum allowable input
slew rate.
5. See Figure 9, “Write Operations Waveform” on page 47.
44
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 19. Write Operations—32 Mbit Density
Density
32 Mbit
Product
#
Sym
70 ns
90 ns
3.0 V – 3.6 V6
Parameter
100 ns
110 ns
90
100
Unit
VCC
2.7 V – 3.6 V
70
90
100
110
Note
Min
Min
Min
Min
Min
Min
W1
tPHWL /
tPHEL
RP# High Recovery to WE# (CE#)
Going Low
4,5
150
150
150
150
150
150
ns
W2
tELWL /
tWLEL
CE# (WE#) Setup to WE# (CE#)
Going Low
4,5
0
0
0
0
0
0
ns
W3
tWLWH
/
tELEH
WE# (CE#) Pulse Width
1,4,5
45
60
60
70
70
70
ns
W4
tDVWH /
tDVEH
Data Setup to WE# (CE#) Going High
2,4,5
40
40
50
60
60
60
ns
W5
tAVWH /
tAVEH
Address Setup to WE# (CE#) Going
High
2,4,5
50
60
60
70
70
70
ns
W6
tWHEH /
tEHWH
CE# (WE#) Hold Time from WE#
(CE#) High
4,5
0
0
0
0
0
0
ns
W7
tWHDX /
tEHDX
Data Hold Time from WE# (CE#)
High
2,4,5
0
0
0
0
0
0
ns
W8
tWHAX /
tEHAX
Address Hold Time from WE# (CE#)
High
2,4,5
0
0
0
0
0
0
ns
W9
tWHWL /
tEHEL
WE# (CE#) Pulse Width High
1,4,5
25
30
30
30
30
30
ns
W10
tVPWH /
tVPEH
VPP Setup to WE# (CE#) Going High
3,4,5
200
200
200
200
200
200
ns
W11
tQVVL
VPP Hold from Valid SRD
3,4
0
0
0
0
0
0
ns
W12
tBHWH /
tBHEH
WP# Setup to WE# (CE#) Going
High
3,4
0
0
0
0
0
0
ns
W13
tQVBL
WP# Hold from Valid SRD
3,4
0
0
0
0
0
0
ns
W14
tWHGL
WE# High to OE# Going Low
3,4
30
30
30
30
30
30
ns
NOTES:
1. Write pulse width (tWP) is defined from CE# or WE# going low (whichever goes low last) to CE# or WE# going high (whichever
goes high first). Hence, tWP = tWLWH = tELEH = tWLEH = tELWH. Similarly, write pulse width high (tWPH) is defined from CE# or
WE# going high (whichever goes high first) to CE# or WE# going low (whichever goes low last). Hence,
tWPH = tWHWL = tEHEL = tWHEL = tEHWL.
2. Refer to Table 7, “Command Bus Operations” on page 24 for valid AIN or DIN.
3. Sampled, but not 100% tested.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and maximum allowable input
slew rate.
5. See Figure 9, “Write Operations Waveform” on page 47.
6. VCCMax = 3.3 V for 32-Mbit 0.25 Micron product.
Datasheet
45
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 20. Write Operations—64Mbit Density
#
Sym
Parameter
VCC
Density
64 Mbit
Product
80 ns
2.7 V – 3.6 V
Note
Min
Unit
W1
tPHWL /
tPHEL
RP# High Recovery to WE# (CE#) Going Low
4,5
150
ns
W2
tELWL /
tWLEL
CE# (WE#) Setup to WE# (CE#) Going Low
4,5
0
ns
W3
tWLWH /
tELEH
WE# (CE#) Pulse Width
1,4,5
60
ns
W4
tDVWH /
tDVEH
Data Setup to WE# (CE#) Going High
2,4,5
40
ns
W5
tAVWH /
tAVEH
Address Setup to WE# (CE#) Going High
2,4,5
60
ns
W6
tWHEH /
tEHWH
CE# (WE#) Hold Time from WE# (CE#) High
4,5
0
ns
W7
tWHDX /
tEHDX
Data Hold Time from WE# (CE#) High
2,4,5
0
ns
W8
tWHAX /
tEHAX
Address Hold Time from WE# (CE#) High
2,4,5
0
ns
W9
tWHWL /
tEHEL
WE# (CE#) Pulse Width High
1,4,5
30
ns
W10
tVPWH /
tVPEH
VPP Setup to WE# (CE#) Going High
3,4,5
200
ns
W11
tQVVL
VPP Hold from Valid SRD
3,4
0
ns
W12
tBHWH /
tBHEH
WP# Setup to WE# (CE#) Going High
3,4
0
ns
W13
tQVBL
WP# Hold from Valid SRD
3,4
0
ns
W14
tWHGL
WE# High to OE# Going Low
3,4
30
ns
NOTES:
1. Write pulse width (tWP) is defined from CE# or WE# going low (whichever goes low last) to CE# or
WE# going high (whichever goes high first). Hence, tWP = tWLWH = tELEH = tWLEH = tELWH.
Similarly, write pulse width high (tWPH) is defined from CE# or WE# going high (whichever goes
high first) to CE# or WE# going low (whichever goes low last). Hence,
tWPH = tWHWL = tEHEL = tWHEL = tEHWL.
2. Refer to Table 7, “Command Bus Operations” on page 24 for valid AIN or DIN.
3. Sampled, but not 100% tested.
4. See Figure 11, “AC Input/Output Reference Waveform” on page 49 for timing measurements and
maximum allowable input slew rate.
5. See Figure 9, “Write Operations Waveform” on page 47.
46
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 9. Write Operations Waveform
W5
W8
Address [A]
W6
CE# [E]
W3
W2
W9
WE# [W]
OE# [G]
W4
W7
Data [D/Q]
W1
RP# [P]
W10
Vpp [V]
8.3
Erase and Program Timings
Table 21. Erase and Program Timings
Symbol
VPP
1.65 V–3.6 V
11.4 V–12.6 V
Note
Typ
Max
Typ
Max
Parameter
Unit
tBWPB
4-KW Parameter Block
Word Program Time
1, 2, 3
0.10
0.30
0.03
0.12
s
tBWMB
32-KW Main Block
Word Program Time
1, 2, 3
0.8
2.4
0.24
1
s
Word Program Time for 0.13
and 0.18 Micron Product
1, 2, 3
12
200
8
185
µs
Word Program Time for 0.25
Micron Product
1, 2, 3
22
200
8
185
µs
tWHQV2 / tEHQV2
4-KW Parameter Block
Erase Time
1, 2, 3
0.5
4
0.4
4
s
tWHQV3 / tEHQV3
32-KW Main Block
Erase Time
1, 2, 3
1
5
0.6
5
s
tWHRH1 / tEHRH1
Program Suspend Latency
1,3
5
10
5
10
µs
tWHRH2 / tEHRH2
Erase Suspend Latency
1,3
5
20
5
20
µs
tWHQV1 / tEHQV1
NOTES:
1. Typical values measured at TA= +25 °C and nominal voltages.
2. Excludes external system-level overhead.
3. Sampled, but not 100% tested.
Datasheet
47
Intel£ Advanced+ Boot Block Flash Memory (C3)
8.4
Reset Specifications
Table 22. Reset Specifications
VCC 2.7 V – 3.6 V
Symbol
Parameter
Notes
Unit
Min
Max
tPLPH
RP# Low to Reset during Read
(If RP# is tied to VCC, this specification is not
applicable)
tPLRH1
RP# Low to Reset during Block Erase
3
22
µs
tPLRH2
RP# Low to Reset during Program
3
12
µs
1, 2
100
ns
NOTES:
1. If tPLPH is < 100 ns the device may still reset but this is not guaranteed.
2. If RP# is asserted while a Block Erase or Word Program operation is not executing, the reset will complete
within 100 ns.
3. Sampled, but not 100% tested.
Figure 10. Reset Operations Waveforms
RP# (P)
VIH
VIL
t PLPH
(A) Reset during Read Mode
t PHQV
t PHWL
t PHEL
Abort
Complete
t PLRH
RP# (P)
VIH
t PHQV
t PHWL
t PHEL
V IL
t PLPH
(B) Reset during Program or Block Erase, t PLPH < t PLRH
Abort Deep
Complete PowerDown
RP# (P)
VIH
V IL
t PLRH
t PHQV
t PHWL
t PHEL
t PLPH
(C) Reset Program or Block Erase, t PLPH > t PLRH
48
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
8.5
AC I/O Test Conditions
Figure 11. AC Input/Output Reference Waveform
VCCQ
VCCQ /2
Input
Test Points
VCCQ/2
Output
0V
NOTE: Input timing begins, and output timing ends, at VCCQ/2. Input rise and fall times (10% to 90%) < 5 ns.
Worst case speed conditions are when VCC = VCCMin.
Figure 12. Transient Equivalent Testing Load Circuit
VCCQ
R1
Device
Under Test
Out
CL
R2
NOTE: See Table 17 for component values.
Table 23. Test Configuration Component Values for Worst Case Speed Conditions
Test Configuration
VCCQMin Standard Test
CL (pF)
R1 (kΩ)
R2 (kΩ)
50
25
25
NOTE: CL includes jig capacitance.
8.6
Device Capacitance
TA = 25 °C, f = 1 MHz
Symbol
CIN
COUT
§
Datasheet
Parameter§
Typ
Max
Unit
Condition
Input Capacitance
6
8
pF
VIN = 0.0 V
Output Capacitance
8
12
pF
VOUT = 0.0 V
Sampled, not 100% tested.
49
Intel£ Advanced+ Boot Block Flash Memory (C3)
Appendix A Write State Machine States
This table shows the command state transitions based on incoming commands.
Command Input (and Next State)
Current State
SR.7
Data
When
Read
Read Array
(FFH)
Program
Setup (10/
40H)
Erase
Setup
(20H)
Erase
Confirm
(D0H)
Read Array
“1”
Array
Read Array
Prog. Setup
Ers. Setup
Prog/Ers
Suspend
(B0H)
Prog/Ers
Resume
(D0)
Read Status
(70H)
Clear
Status
(50H)
Read Array
Read Sts.
Read Array
Read Status
“1”
Status
Read Array
Prog. Setup
Ers. Setup
Read Array
Read Sts.
Read Array
Read Config.
“1”
Config
Read Array
Prog. Setup
Ers. Setup
Read Array
Read Sts.
Read Array
Read Query
“1”
CFI
Read Array
Prog. Setup
Ers. Setup
Read Array
Read Sts.
Read Array
Lock Setup
“1”
Status
Lock Cmd. Error
“1”
Status
Read Array
Prog. Setup
Ers. Setup
Lock Oper. (Done)
“1”
Status
Read Array
Prog. Setup
Ers. Setup
Prot. Prog. Setup
“1”
Status
Protection Register Program
Prot. Prog.
(Not Done)
“0”
Status
Protection Register Program (Not Done)
Lock Command Error
Lock Cmd. Error
Read Array
Read Sts.
Read Array
Read Array
Read Sts.
Read Array
Read Sts.
Read Array
“1”
Status
“1”
Status
Program (Not Done)
“0”
Status
Prog. Susp. Status
“1”
Status
Prog. Sus.
Read Array
Program Suspend
Read Array
Prog. (Not
Done)
Prog. Sus. Rd.
Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Prog. Susp. Read
Array
“1”
Array
Prog. Sus.
Read Array
Program Suspend
Read Array
Prog. (Not
Done)
Prog. Sus. Rd.
Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Prog. Susp. Read
Config
“1”
Config
Prog. Sus.
Read Array
Program Suspend
Read Array
Prog. (Not
Done)
Prog. Sus. Rd.
Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Prog. Susp. Read
Query
“1”
CFI
Prog. Sus.
Read Array
Program Suspend
Read Array
Prog. (Not
Done)
Prog. Sus. Rd.
Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Program (Done)
“1”
Status
Read Array
Read Status
Read Array
Erase
(Not Done)
Erase Cmd.
Error
Status
Erase Cmd. Error
“1”
Status
Ers. Setup
Lock
(Done)
Prog. Setup
“1”
Prog. Setup
Lock
Cmd. Error
Prot. Prog. (Done)
Erase Setup
Read Array
Lock (Done)
Read Array
Program
Prog. Sus.
Status
Program (Not Done)
Prog. Setup
Ers. Setup
Erase Command Error
Read Array
Prog. Setup
Program (Not Done)
Read Array
Ers. Setup
Erase
(Not Done)
Erase Command Error
Read Array
Read Status
Erase Sus.
Status
Erase (Not Done)
Read Array
Erase (Not Done)
“0”
Status
Ers. Susp. Status
“1”
Status
Erase Sus.
Read Array
Prog. Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus. Rd.
Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Erase Susp. Array
“1”
Array
Erase Sus.
Read Array
Prog. Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus. Rd.
Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Ers. Susp. Read
Config
“1”
Config
Erase Sus.
Read Array
Prog. Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus. Rd.
Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Ers. Susp. Read
Query
“1”
CFI
Erase Sus.
Read Array
Prog. Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus. Rd.
Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Erase (Done)
“1”
Status
Read Array
Prog. Setup
Ers. Setup
Read Sts.
Read Array
50
Erase (Not Done)
Read Array
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Command Input (and Next State)
Lock Setup
(60H)
Read Config
(90H)
Read Query
(98H)
Read Array
Read Config.
Read Query
Lock Setup
Prot. Prog. Setup
Read Array
Read Status
Read Config.
Read Query
Lock Setup
Prot. Prog. Setup
Read Array
Read Config.
Read Config.
Read Query
Lock Setup
Prot. Prog. Setup
Read Array
Read Query
Read Config.
Read Query
Lock Setup
Prot. Prog. Setup
Read Array
Lock Setup
Prot. Prog.
Setup (C0H)
Lock Down
Confirm
(2FH)
Current State
Lock Confirm
(01H)
Locking Command Error
Lock Operation (Done)
Lock Cmd. Error
Read Config.
Read Query
Lock Setup
Prot. Prog. Setup
Read Array
Lock Oper.
(Done)
Read Config.
Read Query
Lock Setup
Prot. Prog. Setup
Read Array
Prot. Prog. Setup
Protection Register Program
Prot. Prog.
(Not Done)
Protection Register Program (Not Done)
Prot. Prog.
(Done)
Read Config.
Read Query
Unlock Confirm
(D0H)
Lock Setup
Prot. Prog. Setup
Prog. Setup
Program
Program
(Not Done)
Program (Not Done)
Read Array
Prog. Susp.
Status
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Prog. Susp.
Read Array
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Prog. Susp.
Read Config.
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Prog. Susp.
Read Query.
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Program
(Done)
Read Config.
Read Query
Erase
Setup
Erase Cmd.
Error
Lock Setup
Prot. Prog. Setup
Read Array
Erase
(Not Done)
Erase Command Error
Read Config.
Read Query
Lock Setup
Erase
(Not Done)
Prot. Prog. Setup
Read Array
Erase (Not Done)
Erase Susp.
Status
Ers. Susp. Read
Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Erase Suspend
Array
Ers. Susp. Read
Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Eras Sus. Read
Config
Erase Suspend
Read Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Eras Sus. Read
Query
Erase Suspend
Read Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Ers.(Done)
Read Config.
Read Query
Lock Setup
Datasheet
Prot. Prog. Setup
Read Array
51
Intel£ Advanced+ Boot Block Flash Memory (C3)
Appendix B Flow Charts
Figure 13. Word Program Flowchart
WORD PROGRAM PROCEDURE
Bus
Command
Operation
Start
Write
Write 0x40,
Word Address
(Setup)
Write Data,
Word Address
(Confirm)
Program
Suspend
Loop
Read Status
Register
Program Data = 0x40
Setup
Addr = Location to program
Write
Data
Data = Data to program
Addr = Location to program
Read
None
Status register data: Toggle CE# or
OE# to update Status Register
Idle
None
Check SR[7]
1 = WSM Ready
0 = WSM Busy
No
SR[7] =
0
Suspend?
Yes
Comments
Repeat for subsequent Word Program operations.
Full Status Register check can be done after each program, or
after a sequence of program operations.
1
Full Status
Check
(if desired)
Write 0xFF after the last operation to set to the Read Array
state.
Program
Complete
FULL STATUS CHECK PROCEDURE
Read Status
Register
SR[3] =
Bus
Command
Operation
1
SR[4] =
Idle
None
Check SR[3]:
1 = VP P Error
Idle
None
Check SR[4]:
1 = Data Program Error
Idle
None
Check SR[1]:
1 = Block locked; operation aborted
VP P Range
Error
0
1
Program
Error
1
Device
Protect Error
Comments
0
SR[1] =
0
Program
Successful
52
SR[3] MUST be cleared before the Write State Machine will
allow further program attempts.
If an error is detected, clear the Status Register before
continuing operations - only the Clear Staus Register
command clears the Status Register error bits.
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 14. Program Suspend / Resume Flowchart
PROGRAM SUSPEND / RESUME PROCEDURE
Bus
Operation Command
Start
Write 0xB0
Any Address
Write
(Program Suspend)
Write
Write 0x70
Any Address
Program Data = 0xB0
Suspend Addr = Any address
0
Read
None
Status register data
Toggle CE# or OE# to update Status
register
Addr = Any address
Idle
None
Check SR[7]:
1 = WSM ready
0 = WSM busy
Idle
None
Check SR[2]:
1 = Program suspended
0 = Program completed
Write
Read
Array
Data = 0xFF
Addr = Any address
Read
None
Read array data from block other than
the one being programmed
1
SR[2] =
0
Program
Completed
1
Write 0xFF
(Read Array)
Read Array
Data
Done
Reading
Data = 0x70
Addr = Any address
(Read Status)
Read Status
Register
SR[7] =
Read
Status
Comments
Write 0xFF
No
(Read
Array)
Write
Program Data = 0xD0
Resume Addr = Any address
Read Array
Data
Yes
Write 0xD0
Any Address
(Program Resume)
Program
Resumed
Datasheet
53
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 15. Erase Suspend / Resume Flowchart
ERASE SUSPEND / RESUME PROCEDURE
Bus
Operation Command
Start
Write 0xB0,
Any Address
Write 0x70,
Any Address
Write
Read
Status
Data = 0x70
Addr = Any address
Write
Erase
Suspend
Data = 0xB0
Addr = Any address
Read
None
Status Register data. Toggle CE# or
OE# to update Status register;
Addr = Any Address
Idle
None
Check SR[7]:
1 = WSM ready
0 = WSM busy
Idle
None
Check SR[6]:
1 = Erase suspended
0 = Erase completed
(Erase Suspend)
(Read Status)
Read Status
Register
SR[7] =
0
1
SR[6] =
0
Erase
Completed
Write
1
Write 0xFF
(Read Array)
Read or
Write
Read Array
Data
Done
Reading
Comments
Write
Read Array Data = 0xFF or 0x40
or Program Addr = Any address
None
Read array or program data from/to
block other than the one being erased
Program Data = 0xD0
Resume Addr = Any address
0
1
(Erase Resume)
54
Write 0xD0,
Any Address
Write 0xFF
Erase
Resumed
Read Array
Data
(Read Array)
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 16. Block Erase Flowchart
BLOCK ERASE PROCEDURE
Bus
Comments
Operation Command
Block
Data = 0x20
Write
Erase
Addr = Block to be erased (BA)
Setup
Start
Write 0x20,
Block Address
(Block Erase)
Write
Erase
Confirm
Read
None
Status Register data. Toggle CE# or
OE# to update Status register data
Idle
None
Check SR[7]:
1 = WSM ready
0 = WSM busy
Write 0xD0,
(Erase Confirm)
Block Address
Suspend
Erase
Loop
Read Status
Register
No
0
SR[7] =
Suspend
Erase
1
Data = 0xD0
Addr = Block to be erased (BA)
Yes
Repeat for subsequent block erasures.
Full Status register check can be done after each block erase
or after a sequence of block erasures.
Full Erase
Status Check
(if desired)
Write 0xFF after the last operation to enter read array mode.
Block Erase
Complete
FULL ERASE STATUS CHECK PROCEDURE
Read Status
Register
SR[3] =
Bus
Command
Operation
1
VP P Range
Error
0
SR[4,5] =
1,1
Command
Sequence Error
0
SR[5] =
1
Block Erase
Error
1
Block Locked
Error
0
SR[1] =
0
Block Erase
Successful
Datasheet
Comments
Idle
None
Check SR[3]:
1 = VP P Range Error
Idle
None
Check SR[4,5]:
Both 1 = Command Sequence Error
Idle
None
Check SR[5]:
1 = Block Erase Error
Check SR[1]:
1 = Attempted erase of locked block;
erase aborted.
SR[1,3] must be cleared before the Write State Machine will
allow further erase attempts.
Idle
None
Only the Clear Status Register command clears SR[1, 3, 4, 5].
If an error is detected, clear the Status register before
attempting an erase retry or other error recovery.
55
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 17. Locking Operations Flowchart
LOCKING OPERATIONS PROCEDURE
Start
Write 0x60,
Block Address
(Lock Setup)
Write
Write either
0x01/0xD0/0x2F,
Block Address
(Lock Confirm)
Write
Write 0x90
O ptional
Bus
Command
Operation
(Read Device ID)
No
Yes
Write 0xFF
Any Address
Data = 0x60
Addr = Any Address
Lock,
Data =
Unlock, or
Lock-Down
Confirm Addr =
0x01 (Block Lock)
0xD0 (Block Unlock)
0x2F (Lock-Down Block)
Block to lock/unlock/lock-down
Write
Read
Data = 0x90
(Optional) Device ID Addr = Any Address
Read
Block Lock Block Lock status data
(Optional)
Status
Addr = Block address + offset 2
Read Block
Lock Status
Locking
Change?
Lock
Setup
Comments
Idle
(Optional)
None
Confirm locking change on D[1,0] .
Write
Read
Array
Data = 0xFF
Addr = Any address
(Read Array)
Lock Change
Complete
56
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 18. Protection Register Programming Flowchart
PROTECTION REGISTER PROGRAMMING PROCEDURE
Bus
Command
Operation
Start
Write 0xC0,
PR Address
Program Data = 0xC0
PR Setup Addr = First Location to Program
Write
Protection Data = Data to Program
Program Addr = Location to Program
(Confirm Data)
Read Status
Register
SR[7] =
Write
(Program Setup)
Write PR
Address & Data
Comments
Read
None
Status Register Data. Toggle CE# or
OE# to Update Status Register Data
Idle
None
Check SR[7]:
1 = WSM Ready
0 = WSM Busy
Program Protection Register operation addresses must be
within the Protection Register address space. Addresses
outside this space will return an error.
0
1
Repeat for subsequent programming operations.
Full Status
Check
(if desired)
Full Status Register check can be done after each program, or
after a sequence of program operations.
Write 0xFF after the last operation to set Read Array state.
Program
Complete
FULL STATUS CHECK PROCEDURE
Read Status
Register Data
SR[3], SR[4] =
Bus
Command
Operation
1
Comments
Idle
None
Check SR[1], SR[3], SR[4]:
0,1,1 = VP P Range Error
Idle
None
Check SR[1], SR[3], SR[4]:
0,0,1 = Programming Error
Idle
None
Check SR[1], SR[3], SR[4]:
1,0,1 = Block locked; operation aborted
VP P Range Error
0
SR[3], SR[4] =
1
Program Error
SR[3] must be cleared before the Write State Machine will
allow further program attempts.
0
Only the Clear Staus Register command clears SR[1, 3, 4].
SR[3], SR[4] =
1
Register Locked;
Program Aborted
If an error is detected, clear the Status register before
attempting a program retry or other error recovery.
0
Program
Successful
Datasheet
57
Intel£ Advanced+ Boot Block Flash Memory (C3)
Appendix C Common Flash Interface
This appendix defines the data structure or “database” returned by the Common Flash Interface
(CFI) Query command. System software should parse this structure to gain critical information
such as block size, density, x8/x16, and electrical specifications. Once this information has been
obtained, the software will know which command sets to use to enable flash writes, block erases,
and otherwise control the flash component. The Query is part of an overall specification for
multiple command set and control interface descriptions called Common Flash Interface, or CFI.
C.1
Query Structure Output
The Query database allows system software to obtain information for controlling the flash device.
This section describes the device’s CFI-compliant interface that allows access to Query data.
Query data are presented on the lowest-order data outputs (DQ0-DQ7) only. The numerical offset
value is the address relative to the maximum bus width supported by the device. On this family of
devices, the Query table device starting address is a 0x10, which is a word address for x16 devices.
For a word-wide (x16) device, the first two Query-structure bytes, ASCII “Q” and “R,” appear on
the low byte at word addresses 0x10 and 0x11. This CFI-compliant device outputs 0x00 data on
upper bytes. The device outputs ASCII “Q” in the low byte (DQ0-DQ7) and 0x00 in the high byte
(DQ8-DQ15).
At Query addresses containing two or more bytes of information, the least significant data byte is
presented at the lower address, and the most significant data byte is presented at the higher address.
In all of the following tables, addresses and data are represented in hexadecimal notation, so the
“h” suffix has been dropped. In addition, since the upper byte of word-wide devices is always
“0x00,” the leading “00” has been dropped from the table notation and only the lower byte value is
shown. Any x16 device outputs can be assumed to have 0x00 on the upper byte in this mode.
Table 24. Summary of Query Structure Output as a Function of Device and Mode
Device
Hex Offset
Hex Code
ASCII Value
00010:
51
"Q"
00011:
52
"R"
00012:
59
"Y"
Device Addresses
Table 25. Example of Query Structure Output of x16 Devices (Sheet 1 of 2)
Word Addressing:
Offset
Hex Code
A[X-0]
58
Value
DQ[16:0]
0x00010
0051
"Q"
0x00011
0052
"R"
0x00012
0059
"Y"
0x00013
P_IDLO
PrVendor
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 25. Example of Query Structure Output of x16 Devices (Sheet 2 of 2)
C.2
0x00014
P_IDHI
ID #
0x00015
PLO
PrVendor
0x00016
PHI
TblAdr
0x00017
A_IDLO
AltVendor
0x00018
A_IDHI
ID #
...
...
...
Query Structure Overview
The Query command causes the flash component to display the Common Flash Interface (CFI)
Query structure or “database.” The structure sub-sections and address locations are summarized
below.
Table 26. Query Structure
Offset
Sub-Section Name
0x00000
Description1
Manufacturer Code
0x00001
Device Code
2
0x(BA+2)
Block Status register
Block-specific information
0x00004-0xF
Reserved
Reserved for vendor-specific information
0x00010
CFI query identification
string
Command set ID and vendor data offset
0x0001B
System interface
information
Device timing & voltage information
0x00027
Device geometry definition
Flash device layout
P3
Primary Intel-specific
Extended Query Table
Vendor-defined additional information specific to the Primary
Vendor Algorithm
NOTES:
1. Refer to the Query Structure Output section and offset 0x28 for the detailed definition of offset address as a
function of device bus width and mode.
2. BA = Block Address beginning location (i.e., 0x08000 is block 1’s beginning location when the block size is
32K-word).
3. Offset 15 defines “P” which points to the Primary Intel-specific Extended Query Table.
C.3
Block Status Register
The Block Status Register indicates whether an erase operation completed successfully or whether
a given block is locked or can be accessed for flash program/erase operations.
Block Erase Status (BSR[1]) allows system software to determine the success of the last block
erase operation. BSR[1] can be used just after power-up to verify that the VCC supply was not
accidentally removed during an erase operation.
Datasheet
59
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 27. Block Status Register
Offset
0x(BA+2)1
Length
1
Description
Add.
Value
Block Lock Status Register
BA+2
--00 or --01
BSR[0] Block lock status
0 = Unlocked
BA+2
(bit 0): 0 or 1
BA+2
(bit 1): 0 or 1
BA+2
(bit 2-7): 0
1 = Locked
BSR[1] Block lock-down status
0 = Not locked down
1 = Locked down
BSR[7:2]: Reserved for future use
NOTES:
1. BA = Block Address beginning location (i.e., 0x08000 is block 1’s beginning location when the block size is
32K-word).
C.4
CFI Query Identification String
The Identification String provides verification that the component supports the Common Flash
Interface specification. It also indicates the specification version and supported vendor-specified
command set(s).
Table 28. CFI Identification
Offset
Length
0x10
3
0x13
Description
Add.
Hex Code
Value
Query-unique ASCII string “QRY“
10:
11:
12:
--51
--52
--59
“Q”
“R”
“Y”
2
Primary vendor command set and control interface ID code
16-bit ID code for vendor-specified algorithms
13:
14:
--03
--00
0x15
2
Extended Query Table primary algorithm address
15:
16:
--35
--00
0x17
2
Alternate vendor command set and control interface ID code
0x0000 means no second vendor-specified algorithm exists
17:
18:
--00
--00
0x19
2
Secondary algorithm Extended Query Table address
0x0000 means none exists
19:
1A:
--00
--00
Add.
Hex Code
Value
Table 29. System Interface Information
Offset
Length
0x1B
1
VCC logic supply minimum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 BCD volts
1B:
--27
2.7 V
0x1C
1
VCC logic supply maximum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 BCD volts
1C:
--36
3.6 V
0x1D
1
VPP [programming] supply minimum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 HEX volts
1D:
--B4
11.4 V
60
Description
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Offset
Length
0x1E
1
0x1F
1
0x20
Add.
Hex Code
Value
VPP [programming] supply maximum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 HEX volts
1E:
--C6
12.6 V
“n” such that typical single word program time-out =2n µs
1F:
--05
32 µs
20:
--00
NA
21:
--0A
1s
n
“n” such that typical max. buffer write time-out = 2 µs
1
0x21
Description
n
“n” such that typical block erase time-out = 2 ms
1
n
0x22
1
“n” such that typical full chip erase time-out = 2 ms
22:
--00
NA
0x23
1
“n” such that maximum word program time-out = 2n times typical
23:
--04
512µs
0x24
1
“n” such that maximum buffer write time-out = 2n times typical
24:
--00
NA
25:
--03
8s
26:
--00
NA
Add.
Hex
Code
0x25
n
“n” such that maximum block erase time-out = 2 times typical
1
0x26
n
“n” such that maximum chip erase time-out = 2 times typical
1
C.5
Device Geometry Definition
Table 30. Device Geometry Definition
Offset
Length
Description
0x27
1
“n” such that device size = 2n in number of bytes
0x28
2
Flash device interface:
0x2A
2
“n” such that maximum number of bytes in write buffer = 2n
Value
27
See Table 31
x8 async
x16 async
x8/x16 async
28:
--01
28:00,29:00
28:01,29:00
28:02,29:00
29:
--00
2A:
--00
2B:
--00
2C:
--02
x16
0
Number of erase block regions within device:
0x2C
1
1. x = 0 means no erase blocking; the device erases in “bulk”
2. x specifies the number of device or partition regions
with one or more contiguous same-size erase blocks.
2
3. Symmetrically blocked partitions have one blocking region
4. Partition size = (total blocks) x (individual block size)
0x2D
0x2D
4
14
Erase Block Region 1 Information
bits 0–15 = y, y+1 = number of identical-size erase blocks
2D:
2E:
bits 16–31 = z, region erase block(s) size are z x 256 bytes
2F:
30:
Erase Block Region 2 Information
bits 0–15 = y, y+1 = number of identical-size erase blocks
bits 16–31 = z, region erase block(s) size are z x 256 bytes
31:
32:
33:
See Table 31
See Table 31
34:
Datasheet
61
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 31. Device Geometry Details
16 Mbit
32 Mbit
64 Mbit
Address
C.6
-B
-T
-B
-T
-B
-T
0x27
--15
-15
--16
-16
--17
--17
0x28
--01
--01
--01
--01
--01
--01
0x29
--00
--00
--00
-00
-00
-00
0x2A
--00
--00
--00
-00
-00
-00
0x2B
--00
--00
--00
-00
-00
-00
0x2C
--02
--02
--02
--02
--02
--02
0x2D
--07
--1E
--07
--3E
--07
--7E
0x2E
--00
--00
--00
-00
-00
-00
0x2F
--20
--00
--20
-00
--20
--00
0x30
--00
--01
--00
--01
--00
--01
0x31
--1E
--07
--3E
--07
--7E
--07
0x32
--00
--00
--00
-00
-00
-00
0x33
--00
--20
--00
--20
--00
--20
0x34
--01
--00
--01
--00
--01
--00
Intel-Specific Extended Query Table
Certain flash features and commands are optional. The Intel-Specific Extended Query table
specifies this and other similar types of information.
Table 32. Primary-Vendor Specific Extended Query (Sheet 1 of 2)
Offset1
P = 0x15
Length
0x(P+0)
0x(P+1)
0x(P+2)
3
Primary extended query table
Unique ASCII string “PRI”
0x(P+3)
1
Major version number, ASCII
38:
--31
“1”
0x(P+4)
1
Minor version number, ASCII
39:
--30
“0”
Optional feature and command support (1=yes,
0=no)
bits 9–31 are reserved; undefined bits are “0.” If bit
31 is “1” then another 31 bit field of optional
features follows at the end of the bit-30 field.
3A:
3B:
3C:
3D:
--66
--00
--00
--00
0x(P+5)
0x(P+6)
0x(P+7)
0x(P+8)
62
4
Description
(Optional Flash Features and Commands)
bit 0 Chip erase supported
bit 1 Suspend erase supported
bit 2 Suspend program supported
bit 3 Legacy lock/unlock supported
bit 4 Queued erase supported
bit 5 Instant individual block locking supported
bit 6 Protection bits supported
bit 7 Page mode read supported
bit 8 Synchronous read supported
Address
Hex Code
Value
35:
36:
37:
--50
--52
--49
“P”
“R”
“I”
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
bit 8
=0
=1
=1
=0
=0
=1
=1
=0
=0
No
Yes
Yes
No
No
Yes
Yes
No
No
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Table 32. Primary-Vendor Specific Extended Query (Sheet 2 of 2)
Offset1
P = 0x15
Length
0x(P+9)
1
Description
(Optional Flash Features and Commands)
Supported functions after suspend: Read Array,
Status, Query
Other supported operations are:
bits 1–7 reserved; undefined bits are “0”
Address
Hex Code
3E:
--01
bit 0 Program supported after erase suspend
0x(P+A)
0x(P+B)
2
Block status register mask
bits 2–15 are Reserved; undefined bits are “0”
bit 0 Block Lock-Bit Status Register active
bit 1 Block Lock-Down Bit Status active
bit 0 = 1
Value
Yes
3F:
--03
40:
--00
bit 0 = 1
Yes
bit 1 = 1
Yes
0x(P+C)
1
VCC logic supply highest performance program/
erase voltage
bits 0–3 BCD value in 100 mV
bits 4–7 BCD value in volts
41:
--33
3.3 V
0x(P+D)
1
VPP optimum program/erase supply voltage
bits 0–3 BCD value in 100 mV
bits 4–7 HEX value in volts
42:
--C0
12.0 V
NOTES:
1. The variable P is a pointer which is defined at CFI offset 0x15.
Table 33. Protection Register Information
Offset1
P = 0x35
Length
0x(P+E)
1
Description
(Optional Flash Features and Commands)
Address
Hex
Code
Value
43:
--01
01
44:
45:
46:
--80
--00
--03
80h
00h
8 byte
0x(P+12)
This field describes user-available One Time Programmable (OTP)
Protection register bytes. Some are pre-programmed with deviceunique serial numbers. Others are user programmable. Bits 0–15
point to the Protection register Lock byte, the section’s first byte.
The following bytes are factory pre-programmed and userprogrammable.
bits 0–7 = Lock/bytes JEDEC-plane physical low address
bits 8–15 = Lock/bytes JEDEC -plane physical high address
bits 16–23 = “n” such that 2n = factory pre-programmed bytes
bits 24–31 = “n” such that 2n = user programmable bytes
47:
--03
8 byte
0x(P+13)
Reserved for future use
48:
0x(P+F)
0x(P+10)
(0xP+11)
Number of Protection register fields in JEDEC ID space.
“00h,” indicates that 256 protection bytes are available
Protection Field 1: Protection Description
4
NOTES:
1. The variable P is a pointer which is defined at CFI offset 0x15.
Datasheet
63
Intel£ Advanced+ Boot Block Flash Memory (C3)
Appendix D Mechanical Specifications
Figure 19. µBGA* and VF BGA Package Drawing & Dimensions
R0
Ball A1
Corner
D
1
E
2
3
4
S1
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
F
7
6
5
4
3
Ball A1
Corner
S2
2 1
e
b
Top View - Bump Side down
Bottom View -Bump side up
A
1
A2
A
Seating
Y
Plan
Side View
Note: Drawing not to scale
Dimensions
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Length 8M (.25)
Package Body Length 16M (.25/.18/.13) 32M (.25/.18/.13)
Package Body Length 64M (.18)
Package Body Width 8M (.25)
Package Body Width 16M (.25/.18/.13) 32M (.18/.13)
Package Body Width 32M (.25)
Package Body Width 64M (.18)
Pitch
Ball (Lead) Count 8M, 16M
Ball (Lead) Count 32M
Ball (Lead) Count 64M
Seating Plane Coplanarity
Corner to Ball A1 Distance Along D 8M (.25)
Corner to Ball A1 Distance Along D 16M (.25/.18/.13) 32M (.18/.13)
Corner to Ball A1 Distance Along D 64M (.18)
Corner to Ball A1 Distance Along E 8M (.25)
Corner to Ball A1 Distance Along E 16M (.25/.18/.13) 32M (.18/.13)
Corner to Ball A1 Distance Along E 32M (.25)
Corner to Ball A1 Distance Along E 64M (.18)
64
Symbol
A
A1
A2
b
D
D
D
E
E
E
E
e
N
N
N
Y
S1
S1
S1
S2
S2
S2
S2
Min
Millimeters
Nom
Max
1.000
0.150
0.325
7.810
7.186
7.600
6.400
6.864
10.750
8.900
1.230
0.918
1.125
1.275
1.507
3.450
2.525
Min
Inches
Nom
Max
0.0394
0.0059
0.665
0.375
7.910
7.286
7.700
6.500
6.964
10.850
9.000
0.750
46
47
48
1.330
1.018
1.225
1.375
1.607
3.550
2.625
0.425
8.010
7.386
7.800
6.600
7.064
10.860
9.100
0.100
1.430
1.118
1.325
1.475
1.707
3.650
2.725
0.0128
0.0262
0.0148
0.2829
0.2992
0.2520
0.2702
0.4232
0.3504
0.2868
0.3031
0.2559
0.2742
0.4272
0.3543
0.0295
46
47
48
0.0484
0.0361
0.0443
0.0502
0.0593
0.1358
0.0994
0.0524
0.0401
0.0482
0.0541
0.0633
0.1398
0.1033
0.0167
0.2908
0.3071
0.2598
0.2781
0.4276
0.3583
0.0039
0.0563
0.0440
0.0522
0.0581
0.0672
0.1437
0.1073
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 20. TSOP Package Drawing & Dimensions
Z
A2
See Notes 1, 2, 3 and 4
Pin 1
e
See Detail B
E
Y
D1
A1
D
Seating
Plane
See Detail A
A
Detail A
Detail B
C
b
0
L
A5568-02
Dimensions
Family: Thin Small Out
-Line Package
Symbol
Millimeters
Min
1.
2.
3.
4.
Datasheet
Package Height
A
Nom
Inches
Max
Notes
Min
Nom
1.200
Max
Standoff
A1
0.050
Package Body Thickness
A2
0.950
1.000
1.050
0.037
0.039
0.041
Lead Width
b
0.150
0.200
0.300
0.006
0.008
0.012
0.002
0.100
0.150
Lead Thickness
c
0.200
0.004
0.006
0.008
Plastic Body Length
D1
18.200 18.400 18.600
0.717
0.724
0.732
Package Body Width
E
11.800 12.000 12.200
0.465
0.472
0.480
Lead Pitch
e
0.500
Terminal Dimension
D
19.800 20.000 20.200
Lead Tip Length
L
Lead Count
N
Lead Tip Angle
Ø
Seating Plane Coplanarity
Y
Lead to Package Offset
Z
0.500
Notes
0.047
0.600
0.0197
0.780
0.787
0.795
0.700
0.020
0.024
0.028
5°
0°
3°
0.006
0.010
48
0°
3°
0.150
0.250
48
0.100
0.350
5°
0.004
0.014
One dimple on package denotes Pin 1.
If two dimples, then the larger dimple denotes Pin 1.
Pin 1 will always be in the upper left corner of the package, in reference to the product mark.
Pin 1 will always supersede above pin one notes.
65
Intel£ Advanced+ Boot Block Flash Memory (C3)
Figure 21. Easy BGA Package Drawing & Dimension
Ball A1
Corner
D
1
E
2
3
4
Ball A1
Corner
S1
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
7
6
5
4
3
2
1
S2
b
e
Top View - Ball side down
Bottom View - Ball Side Up
A1
A2
A
Seating
Y
Plane
Side View
Note: Drawing not to scale
Dimensions Table
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Width
Package Body Length
Pitch
Ball (Lead) Count
Seating Plane Coplanarity
Corner to Ball A1 Distance Along D
Corner to Ball A1 Distance Along E
Symbol
A
A1
A2
b
D
E
[e]
N
Y
S1
S2
Millimeters
Min
Nom
Max
1.200
Notes
0.250
0.330
9.900
12.900
1.400
2.900
Inches
Min
Nom
Max
0.0472
0.0098
0.780
0.430
10.000
13.000
1.000
64
1.500
3.000
0.530
10.100
13.100
1
1
0.0130
0.3898
0.5079
0.100
1.600
3.100
1
1
0.0551
0.1142
0.0307
0.0169
0.3937
0.5118
0.0394
64
0.0591
0.1181
0.0209
0.3976
0.5157
0.0039
0.0630
0.1220
Note: (1) Package dimensions are for reference only. These dimensions are estimates based
on die size, and are subject to change.
66
Datasheet
Intel£ Advanced+ Boot Block Flash Memory (C3)
Appendix E Additional Information
Order Number
Document/Tool
297938
3 Volt Advanced+ Boot Block Flash Memory Specification Update
292216
AP-658 Designing for Upgrade to the Advanced+ Boot Block Flash Memory
292215
AP-657 Designing with the Advanced+ Boot Block Flash Memory
Architecture
Contact your Intel
Representative
297874
Intel® Flash Data Integrator (FDI) Software Developer’s Kit
IFDI Interactive: Play with Intel® Flash Data Integrator on Your PC
NOTES:
1. Please call the Intel Literature Center at (800) 548-4725 to request Intel documentation. International
customers should contact their local Intel or distribution sales office.
2. Visit Intel’s World Wide Web home page at ‘http://www.intel.com/design/flash’ for technical
documentation and tools.
Datasheet
67
Intel£ Advanced+ Boot Block Flash Memory (C3)
Appendix F Ordering Information
Figure 22. Component Ordering Information
T E2 8 F 3 2 0 C3 T C7 0
Access Speed (ns)
(70, 80, 90, 100, 110)
Package
TE = 48-Lead TSOP
GT = 48-Ball µBGA* CSP
GE = VF BGA CSP
RC = Easy BGA
Lithography
A = 0.25 µm
C = 0.18 µm
D = 0.13 µm
Product line designator
for all Intel® Flash products
T = Top Parameter Boot
B = Bottom Parameter Boot
Device Density
640 = x16 (64 Mbit)
320 = x16 (32 Mbit)
160 = x16 (16 Mbit)
800 = x16 (8 Mbit)
Product Family
C3 = 3 Volt Advanced+ Boot Block
VCC = 2.7 V–3.6 V
VPP = 2.7 V–3.6 V or
11.4 V–12.6 V
VALID COMBINATIONS (All Extended Temperature)
48-Lead TSOP
Extended
64 Mbit
TE28F640C3TC80
TE28F640C3BC80
Extended
32 Mbit
TE28F320C3TD70
TE28F320C3BD70
TE28F320C3TC70
TE28F320C3BC70
TE28F320C3TC90
TE28F320C3BC90
TE28F320C3TA100
TE28F320C3BA100
TE28F320C3TA110
TE28F320C3BA110
Extended
16 Mbit
TE28F160C3TD70
TE28F160C3BD70
TE28F160C3TC70
TE28F160C3BC70
TE28F160C3TC80
TE28F160C3BC80
TE28F160C3TC90
TE28F160C3BC90
TE28F160C3TA90
TE28F160C3BA90
TE28F160C3TA110
TE28F160C3BA110
Extended
8 Mbit
TE28F800C3TA90
TE28F800C3BA90
TE28F800C3TA110
TE28F800C3BA110
48-Ball µBGA* CSP
GT28F320C3TA100
GT28F320C3BA100
GT28F320C3TA110
GT28F320C3BA110
GT28F160C3TA90
GT28F160C3BA90
GT28F160C3TA110
GT28F160C3BA110
48-Ball VF BGA
Easy BGA
GE28F640C3TC80
GE28F640C3BC80
RC28F640C3TC80
RC28F640C3BC80
GE28F320C3TD70
GE28F320C3BD70
GE28F320C3TC70
GE28F320C3BC70
GE28F320C3TC90
GE28F320C3BC90
RC28F320C3TD70
RC28F320C3BD70
RC28F320C3TD90
RC28F320C3BD90
RC28F320C3TC90
RC28F320C3BC90
RC28F320C3TA100
RC28F320C3BA100
RC28F320C3TA110
RC28F320C3BA110
GE28F160C3TD70
GE28F160C3BD70
GE28F160C3TC70
GE28F160C3BC70
GE28F160C3TC80
GE28F160C3BC80
GE28F160C3TC90
GE28F160C3BC90
GE28F800C3TA70
GE28F800C3BA70
GE28F800C3TA90
GE28F800C3BA90
RC28F160C3TD70
RC28F160C3BD70
RC28F160C3TC70
RC28F160C3BC70
RC28F160C3TC80
RC28F160C3BC80
RC28F160C3TC90
RC28F160C3BC90
RC28F160C3TA90
RC28F160C3BA90
RC28F160C3TA110
RC28F160C3BA110
RC28F800C3TA90
RC28F800C3BA90
RC28F800C3TA110
RC28F800C3BA110
NOTE: The second line of the 48-ball µBGA package top side mark specifies assembly codes. For samples
only, the first character signifies either “E” for engineering samples or “S” for silicon daisy chain
samples. All other assembly codes without an “E” or “S” as the first character are production units.
68
Datasheet
Similar pages