TOCOS GF16L10RB102K 16mm diameter, single-turn, cermet industrial panel control Datasheet

TOCOS
®
GF16 Series
PA N E L C O N T R O L S
16mm Diameter, Single-Turn, Cermet Industrial Panel Controls
GFP16
GF16
Features
16mm diameter, single-turn industrial panel controls Cermet film element Single unit, single shaft
Excellent environmental characteristics Wide temperature range of 55C to 125C Metal shaft and bushing
Linear taper Shaft lock available Panel and PCB mounting styles Lug or right angle mount pin terminals
3.2mm diameter shafts in slot, flat or round end styles Standard 10mm or 15mm shaft length
Specifications
Electrical
Environmental
Standard Resistance Range . . . . . . . . . . . . . 100Ω to 1MΩ
Temperature Range . . . . . . . . . . . . . . . . . 55C to 125C
Resistance Tolerance . . . . . . . . . . . . . . . . . 20% standard
(10% special order )
High Temperature Exposure . . . . . . . . . 120C, 250 hours
∆T/R )4%
End Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Ω max.
Load Life . . . . . . . . . . . . 70C, 1,000 hours with rated load
∆T/R )5%
Resistance Taper . . . . . . . . . . . . . . . . . . . . . . . . . . B = linear
Peak Noise (C.R.V.) . . . . . . . 3% or 5Ω, whichever is greater
Power Rating . . . . . . . . 0.5 watt at 70C, 0 watt at 120C
Maximum Input Voltage . . . . . . . . 400VDC or power rating,
whichever is smaller
Temperature Coefficient . . . 100 ppm /C, 200Ω to 500kΩ
250 ppm /C, other values
Insulation Resistance . . . . . . 500MΩ minimum at 500VDC
Dielectric Strength . . . . . . . . . . . . . . . . . . 500VAC, 1 minute
Mechanical
Mechanical Travel . . . . . . . . . . . . . . . . . . . . . . . . . 26010
Thermal Shock . . . . . . . . . . . . . . . . . . . . . .55C ~120C,
5 cycles without load
∆T/R )3%
Vibration . . . . . . . . . . . . . . . . . . .10-55Hz, 1.5mm amplitude,
3 directions, 2 hours each
∆T/R )2%
Soldering Heat Resistance . . . . . . . . . . . 350C, 3 seconds
∆T/R )1%
Rotational Life . . . . 15,000 cycles (500 cycles for shaft lock
models only) without load
∆T/R )4%
∆T/R = Total Resistance Change
Shaft Torque . . . . . . 20 to 200 gf • cm (0.277 to 2.773 oz • in)
Stop Strength . . . . . . . . . . . . . 3 kgf • cm (41.59 oz • in) max.
Mounting Nut Torque . . . . . .10.2 kgf • cm (141.4 oz • in) max.
Solderability . . . . . . . . . . . . . . . . . . . . . . . 235C, 5 seconds
Marking . . . . . . . . . . . . . . . . . Model type, taper, resistance,
shaft type, terminal identification, date code
TOCOS AMERICA, INC.
74
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
E-mail: [email protected]
www.tocos.com
GF16 Series
Dimensions
GF16
Unit: mm
Panel Mount, Single Unit, Single Shaft
Right Angle Ear-Lug Terminals, 3-Lug Inline Pattern
Recommended
Panel Mounting Hole
GF16L
Panel Mount, Single Unit, Single Shaft with Shaft Lock
Right Angle Ear-Lug Terminals, 3-Lug Inline Pattern
Recommended
Panel Mounting Hole
GFP16
PCB Mount, Single Unit, Single Shaft
Right Angle Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Rear Support Bracket
Recommended
PCB Mounting Holes
TOCOS AMERICA, INC.
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
75
E-mail: [email protected]
www.tocos.com
GF16 Series
Dimensions
GFP16L
Unit: mm
PCB Mount, Single Unit, Single Shaft with Shaft Lock
Right Angle Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Rear Support Bracket
Recommended
PCB Mounting Holes
TOCOS AMERICA, INC.
76
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
E-mail: [email protected]
www.tocos.com
GF16 Series
Part Numbering System
GF P 16 L 10 S B 103 M
NOTE: FMS = From Mounting Surface
Resistance Tolerance: M = 20% (standard).
K = 10% (special order ).
Resistance Code: Expressed in ohms. A three digit code where the first
two digits are significant figures, and the third digit indicates the number
of zeros that follow these figures (i.e., 100 = 10Ω; 101 = 100Ω; 102 = 1,000Ω;
103 = 10,000Ω; 105 = 1,000,000Ω ). See table for standard resistance values.
Resistance Taper: B = Linear.
Shaft End Style: S = Slotted.
F = Flatted.
R = Round.
Standard Shaft Length: 10 = 10mm FMS.
15 = 15mm FMS.
Up to 30mm shaft length available (special order ).
Shaft Lock: L = With Shaft Lock.
Blank = Without Shaft Lock.
Size: 16 = 16mm Diameter.
Style: Blank = Panel Mount, Single Unit, Single Shaft, Right Angle
Ear-Lug Terminals, 3-Lug Inline Pattern.
P = PCB Mount, Single Unit, Single Shaft, Right Angle
Mount Pin Terminals, 3-Pin Inline Pattern, 2-Pin Rear
Support Bracket.
TOCOS Series Name: GF = Cermet Film Element.
Standard Resistance Values and Part Numbering Codes
Standard Nominal Total Resistance Values and Part Numbering Codes
Resistance ( Ω )
Code
Resistance ( Ω )
Code
Resistance ( Ω )
Code
Resistance ( Ω )
Code
Resistance ( Ω )
Code
100
200
500
101
201
501
1,000
2,000
5,000
102
202
502
10,000
20,000
50,000
103
203
503
100,000
200,000
500,000
104
204
504
1,000,000
105
Refer to Shaft End Styles Specifications and Hardware Specifications for details and availability.
For additional information, refer to Guidelines and Precautions for Using Panel Controls.
TOCOS AMERICA, INC.
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
77
E-mail: [email protected]
www.tocos.com
Similar pages