Intel GT28F320C3T90 3 volt advanced boot block 8-, 16-, 32-mbit flash memory family Datasheet

E
PRODUCT PREVIEW
3 VOLT ADVANCED+ BOOT BLOCK
8-, 16-, 32-MBIT
FLASH MEMORY FAMILY
28F008C3, 28F016C3, 28F032C3
28F800C3, 28F160C3, 28F320C3
n
n
n
n
n
n
Flexible SmartVoltage Technology
 2.7 V–3.6 V Read/Program/Erase
 2.7 V or 1.65 V I/O Option Reduces
Overall System Power
 12 V for Fast Production
Programming
High Performance
 2.7 V–3.6 V: 90 ns Max Access Time
 3.0 V–3.6 V: 80 ns Max Access Time
Optimized Architecture for Code Plus
Data Storage
 Eight 8-Kbyte Blocks,
Top or Bottom Locations
 Up to Sixty-Three 64-KB Blocks
 Fast Program Suspend Capability
 Fast Erase Suspend Capability
Flexible Block Locking
 Lock/Unlock Any Block
 Full Protection on Power-Up
 WP# Pin for Hardware Block
Protection
 VPP = GND Option
 VCC Lockout Voltage
Low Power Consumption
 9 mA Typical Read Power
 10 µA Typical Standby Power with
Automatic Power Savings Feature
Extended Temperature Operation
 –40 °C to +85 °C
n
n
n
n
n
n
n
n
n
n
Easy-12 V
 Faster Production Programming
 No Additional System Logic
128-bit Protection Register
 64-bit Unique Device Identifier
 64-bit User Programmable OTP
Cells
Extended Cycling Capability
 Minimum 100,000 Block Erase
Cycles
Flash Data Integrator Software
 Flash Memory Manager
 System Interrupt Manager
 Supports Parameter Storage,
Streaming Data (e.g., voice)
Automated Word/Byte Program and
Block Erase
 Command User Interface
 Status Registers
SRAM-Compatible Write Interface
Cross-Compatible Command Support
 Intel Basic Command Set
 Common Flash Interface
x 16 for High Performance
 48-Ball µBGA* Package
 48-Lead TSOP Package
x 8 I/O for Space Savings
 48-Ball µBGA* Package
 40-Lead TSOP Package
0.25 µ ETOX™ VI Flash Technology
The 0.25 µm 3 Volt Advanced+ Boot Block, manufactured on Intel’s latest 0.25 µ technology, represents a
feature-rich solution at overall lower system cost. Smart 3 flash memory devices incorporate low voltage
capability (2.7 V read, program and erase) with high-speed, low-power operation. Flexible block locking
allows any block to be independently locked or unlocked. Add to this the Intel-developed Flash Data
Integrator (FDI) software and you have a cost-effective, flexible, monolithic code plus data storage solution on
the market today. 3 Volt Advanced+ Boot Block products will be available in 48-lead TSOP, 40-lead TSOP,
and 48-ball µBGA* packages. Additional information on this product family can be obtained by accessing
Intel’s WWW page: http://www.intel.com/design/flcomp.
May 1998
Order Number: 290645-001
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of
Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to
sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life
saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
The 28F008C3, 28F016C3, 28F032C3, 28F800C3, 28F160C3, 28F320C3 may contain design defects or errors known as
errata which may cause the product to deviate from published specifications. Current characterized errata are available on
request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be
obtained from:
Intel Corporation
P.O. Box 5937
Denver, CO 80217-9808
or call 1-800-548-4725
or visit Intel’s website at http:\\www.intel.com
COPYRIGHT © INTEL CORPORATION 1998
*Third-party brands and names are the property of their respective owners.
CG-041493
E
3 VOLT ADVANCED+ BOOT BLOCK
CONTENTS
PAGE
1.0 INTRODUCTION .............................................5
1.1 3 Volt Advanced+ Boot Block Flash Memory
Enhancements ............................................5
1.2 Product Overview.........................................6
2.0 PRODUCT DESCRIPTION..............................6
2.1 Package Pinouts ..........................................6
2.2 Block Organization .....................................10
2.2.1 Parameter Blocks ................................10
2.2.2 Main Blocks .........................................10
3.0 PRINCIPLES OF OPERATION .....................11
3.1 Bus Operation ............................................11
3.1.1 Read....................................................11
3.1.2 Output Disable.....................................11
3.1.3 Standby ...............................................11
3.1.4 Reset...................................................12
3.1.5 Write....................................................12
3.2 Modes of Operation....................................12
3.2.1 Read Array ..........................................12
3.2.2 Read Configuration..............................13
3.2.3 Read Status Register ..........................13
3.2.3.1 Clearing the Status Register .........13
3.2.4 Read Query .........................................13
3.2.5 Program Mode.....................................14
3.2.5.1 Suspending and Resuming
Program.......................................14
3.2.6 Erase Mode .........................................14
3.2.6.1 Suspending and Resuming Erase.15
3.3 Flexible Block Locking................................19
3.3.1 Locking Operation ...............................19
3.3.2 Locked State .......................................19
3.3.3 Unlocked State ....................................19
3.3.4 Lock-Down State .................................19
3.3.5 Reading a Block’s Lock Status ............20
3.3.6 Locking Operations during Erase
Suspend.............................................20
3.3.7 Status Register Error Checking ...........20
PRODUCT PREVIEW
PAGE
3.4 128-Bit Protection Register.........................21
3.4.1 Reading the Protection Register ..........21
3.4.2 Programming the Protection Register ..21
3.4.3 Locking the Protection Register ...........22
3.5 VPP Program and Erase Voltages...............22
3.5.1 Easy-12 V Operation for Fast
Manufacturing Programming...............22
3.5.2 VPP ≤ VPPLK for Complete Protection ...22
3.5.3 VPP Usage ...........................................22
3.6 Power Consumption ...................................23
3.6.1 Active Power (Program/Erase/Read) ...23
3.6.2 Automatic Power Savings (APS) .........23
3.6.3 Standby Power ....................................23
3.6.4 Deep Power-Down Mode.....................24
3.7 Power-Up/Down Operation.........................24
3.7.1 RP# Connected to System Reset ........24
3.7.2 VCC, VPP and RP# Transitions .............24
3.8 Power Supply Decoupling ..........................24
4.0 ABSOLUTE MAXIMUM RATINGS ................25
4.2 Operating Conditions..................................25
4.3 Capacitance ...............................................26
4.4 DC Characteristics .....................................26
4.5 AC Characteristics—Read Operations—
Extended Temperature..............................30
4.6 AC Characteristics—Write Operations—
Extended Temperature..............................32
4.7 Erase and Program Timings .......................33
4.8 Reset Operations .......................................35
5.0 ORDERING INFORMATION..........................36
6.0 ADDITIONAL INFORMATION .......................37
APPENDIX A: WSM Current/Next States ..........38
APPENDIX B: Program/Erase Flowcharts ........40
APPENDIX C: Common Flash Interface Query
Structure ......................................................46
3
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX D: Architecture Block Diagram ......52
APPENDIX G: Device ID Table ..........................57
APPENDIX E: Word-Wide Memory Map
Diagrams .....................................................53
APPENDIX H: Protection Register
Addressing ..................................................58
APPENDIX F: Byte-Wide Memory Map
Diagrams .....................................................55
REVISION HISTORY
4
Date of
Revision
Version
05/12/98
-001
Description
Original version
PRODUCT PREVIEW
E
1.0
3 VOLT ADVANCED+ BOOT BLOCK
INTRODUCTION
1.1
This document contains the specifications for the
3 Volt Advanced+ Boot Block flash memory family.
These flash memories add features which can be
used to enhance the security of systems: instant
block locking and a protection register.
3 Volt Advanced+ Boot Block
Flash Memory Enhancements
The 3 Volt Advanced+ Boot Block flash memory
features:
Throughout this document, the term “2.7 V” refers
to the full voltage range 2.7 V–3.6 V (except where
noted otherwise) and “VPP = 12 V” refers to 12 V
±5%. Sections 1 and 2 provide an overview of the
flash memory family including applications, pinouts,
pin descriptions and memory organization. Section
3 describes the operation of these products. Finally,
Section 4 contains the operating specifications.
•
Zero-latency, flexible block locking
•
128-bit Protection Register
•
Simple system implementation for 12 V
production programming with 2.7 V in-field
programming
•
Ultra-low power operation at 2.7 V
•
Minimum 100,000 block erase cycles
•
Common Flash Interface for software query of
device specs and features
Table 1. 3 Volt Advanced+ Boot Block Feature Summary
8 M(2)
16 M
32 M(1)
Feature
8 M(2)
16 M
32 M
VCC Operating Voltage
VPP Voltage
2.7 V – 3.6 V
Table 8
Provides complete write protection with
optional 12V Fast Programming
Table 8
2.7 V– 3.6 V
Note 3
VCCQ I/O Voltage
Bus Width
8-bit
Speed (ns)
Blocking (top or bottom)
Reference
16-bit
90, 110 @ 2.7 V and 80, 100 @ 3.0 V
8 x 8-Kbyte parameter
8 x 4-Kword parameter
4-Mb: 7 x 64-Kbyte main
8-Mb: 15 x 64-Kbyte main
16-Mb: 31 x 64-Kbyte main
32-Mb: 63 x 64-Kbyte main
4-Mb: 7 x 32-Kword main 8Mb: 15 x 32-Kword main
16-Mb: 31 x 32-Kword main
32-Mb: 63 x 32-Kword main
Table 2
Table 11
Section 2.2
Appendix E and F
Operating Temperature
Extended: –40 °C to +85 °C
Table 8
Program/Erase Cycling
100,000 cycles
Table 8
Packages
Block Locking
Protection Register
40-Lead TSOP(1)
48-Ball µBGA* CSP(2)
48-Lead TSOP
48-Ball µBGA* CSP(2)
Figures 1, 2, 3,
and 4
Flexible locking of any block with zero latency
Section 3.3
64-bit unique device number, 64-bit user programmable
Section 3.4
NOTES:
1. 32-Mbit density not available in 40-lead TSOP.
2. 8-Mbit density not available in µBGA* CSP.
3. VCCQ operation at 1.65 V — 2.5 V available upon request.
PRODUCT PREVIEW
5
E
3 VOLT ADVANCED+ BOOT BLOCK
1.2
Product Overview
Intel provides secure low voltage memory solutions
with the Advanced Boot Block family of products. A
new block locking feature allows instant
locking/unlocking of any block with zero-latency. A
128-bit protection register allows unique flash
device identification.
Discrete supply pins provide single voltage read,
program, and erase capability at 2.7 V while also
allowing 12 V VPP for faster production
programming. Easy-12 V, a new feature designed
to reduce external logic, simplifies board designs
when combining 12 V production programming with
2.7 V in-field programming.
The 3 Volt Advanced+ Boot Block flash memory
products are available in either x8 or x16 packages
in the following densities: (see Section 6, Ordering
Information)
•
8-Mbit (8,388,608 bit) flash memories organized
as either 512 Kwords of 16 bits each or 1024
Kbytes or 8 bits each.
•
16-Mbit (16,777,216 bit) flash memories
organized as either 1024 Kwords of 16 bits
each or 2048 Kbytes of 8 bits each.
•
32-Mbit (33,554,432 bit) flash memories
organized as either 2048 Kwords of 16 bits
each or 4096 Kbytes of 8 bits each.
Eight 8-KB parameter blocks are located at either
the top (denoted by -T suffix) or the bottom (-B
suffix) of the address map in order to accommodate
different microprocessor protocols for kernel code
location. The remaining memory is grouped into 64Kbyte main blocks.
All blocks can be locked or unlocked instantly to
provide complete protection for code or data. (see
Section 3.3 for details).
The Command User Interface (CUI) serves as the
interface
between
the
microprocessor
or
microcontroller and the internal operation of the
flash memory. The internal Write State Machine
(WSM) automatically executes the algorithms and
timings necessary for program and erase
operations,
including
verification,
thereby
unburdening the microprocessor or microcontroller.
6
The status register indicates the status of the WSM
by signifying block erase or word program
completion and status.
Program and erase automation allows program and
erase operations to be executed using an industrystandard two-write command sequence to the CUI.
Program operations are performed in word or byte
increments. Erase operations erase all locations
within a block simultaneously. Both program and
erase operations can be suspended by the system
software in order to read from any other block. In
addition, data can be programmed to another block
during an erase suspend.
The 3 Volt Advanced+ Boot Block flash memories
offer two low power savings features: Automatic
Power Savings (APS) and standby mode. The
device automatically enters APS mode following the
completion of a read cycle. Standby mode is
initiated when the system deselects the device by
driving CE# inactive. Combined, these two power
savings features significantly reduce power
consumption.
The device can be reset by lowering RP# to GND.
This provides CPU-memory reset synchronization
and additional protection against bus noise that
may occur during system reset and power-up/down
sequences (see Section 3.5 and 3.6).
Refer to the DC Characteristics Section 4.4 for
complete current and voltage specifications. Refer
to the AC Characteristics Sections 4.5 and 4.6, for
read and write performance specifications. Program
and erase times and shown in Section 4.7.
2.0
PRODUCT DESCRIPTION
This section provides device pin descriptions and
package pinouts for the 3 Volt Advanced+ Boot
Block flash memory family, which is available in 40Lead TSOP (x8, Figure 1), 48-lead TSOP (x16,
Figure 2) and 48-ball µBGA packages (Figures 3
and 4).
2.1
Package Pinouts
In each diagram, upgrade pins from one density to
the next are circled.
PRODUCT PREVIEW
E
A16
A15
A14
A13
A12
A11
A9
A8
WE#
RP#
VPP
WP#
A18
A7
A6
A5
A4
A3
A2
A1
3 VOLT ADVANCED+ BOOT BLOCK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Advanced Boot
40-Lead TSOP
10 mm x 20 mm
TOP VIEW
A17
GND
A20
16M
A19
8M
A10
DQ7
DQ6
DQ5
DQ4
VCCQ
VCC
NC
DQ3
DQ2
DQ1
DQ0
OE#
GND
CE#
A0
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
NOTES:
1. 40-Lead TSOP available for 8- and 16-Mbit densities only.
2. Lower densities will have NC on the upper address pins. For example, an 8-Mbit device will have NC on Pin 38.
Figure 1. 40-Lead TSOP Package for x8 Configurations
32M
16M
8M
A 15
A 14
A 13
A12
A11
A 10
A9
A8
A 20
NC
WE#
RP#
V PP
WP#
A19
A 18
A 17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Advanced Boot Block
48-Lead TSOP
12 mm x 20 mm
TOP VIEW
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A 16
VCCQ
GND
DQ15
DQ 7
DQ 14
DQ 6
DQ 13
DQ 5
DQ 12
DQ 4
V CC
DQ 11
DQ 3
DQ 10
DQ 2
DQ 9
DQ 1
DQ 8
DQ 0
OE#
GND
CE#
A0
NOTE:
Lower densities will have NC on the upper address pins. For example, an 8-Mbit device will have NC on Pins 9 and 15.
Figure 2. 48-Lead TSOP Package for x16 Configurations
PRODUCT PREVIEW
7
E
3 VOLT ADVANCED+ BOOT BLOCK
1
2
3
4
5
6
7
8
16M
A
A13
A 11
A8
VPP
WP#
A19
A7
A4
B
A14
A10
WE#
RP#
A18
A17
A5
A2
C
A15
A12
A9
A 20
A6
A3
A1
D
A16
D14
D5
D11
D2
D8
CE#
A0
E
VCCQ
D15
D6
D12
D3
D9
D0
GND
GND
D7
D13
D4
VCC
D10
D1
OE#
32M
F
NOTES:
1. Shaded connections indicate the upgrade address connections. Lower density devices will not have the upper address
solder balls. Routing is not recommended in this area. A19 is the upgrade address for the 16-Mbit device. A20 is the
upgrade address for the 32-Mbit device.
2. 8-Mbit not available on µBGA* CSP.
Figure 3. x16 48-Ball µBGA* Chip Size Package (Top View, Ball Down)
1
2
3
4
5
6
7
8
16M
A
A14
A12
A8
VPP
WP#
A20
A7
A4
B
A 15
A 10
WE#
RP#
A 19
A 18
A5
A2
C
A16
A 13
A9
A21
A6
A3
A1
D
A17
NC
D5
NC
D2
NC
CE#
A0
E
VCCQ
A 11
D6
NC
D3
NC
D0
GND
GND
D7
NC
D4
VCC
NC
D1
OE#
32M
F
NOTES:
1. Shaded connections indicate the upgrade address connections. Lower density devices will not have the upper address
solder balls. Routing is not recommended in this area. A20 is the upgrade address for the 16-Mbit device. A21 is the
upgrade address for the 32-Mbit device.
2. 8-Mbit not available on µBGA* CSP.
Figure 4. x8 48-Ball µBGA* Chip Size Package (Top View, Ball Down)
8
PRODUCT PREVIEW
E
Symbol
A0–A21
3 VOLT ADVANCED+ BOOT BLOCK
Table 2. 3 Volt Advanced+ Boot Block Pin Descriptions
Type
INPUT
Name and Function
ADDRESS INPUTS for memory addresses. Addresses are internally
latched during a program or erase cycle.
8-Mbit x 8 A[0-19], 16-Mbit x 8 A[0-20], 32-Mbit x 8 A[0-21]
8-Mbit x 16 A[0-18], 16-Mbit x 16 A[0-19], 32-Mbit x 16 A[0-20]
DQ0–DQ7
INPUT/OUTPUT
DATA INPUTS/OUTPUTS: Inputs array data on the second CE# and
WE# cycle during a Program command. Inputs commands to the
Command User Interface when CE# and WE# are active. Data is
internally latched. Outputs array, configuration and status register data.
The data pins float to tri-state when the chip is de-selected or the outputs
are disabled.
DQ8–DQ15
INPUT/OUTPUT
DATA INPUTS/OUTPUTS: Inputs array data on the second CE# and
WE# cycle during a Program command. Data is internally latched.
Outputs array and configuration data. The data pins float to tri-state when
the chip is de-selected. Not included on x8 products.
CE#
INPUT
CHIP ENABLE: Activates the internal control logic, input buffers,
decoders and sense amplifiers. CE# is active low. CE# high de-selects
the memory device and reduces power consumption to standby levels.
OE#
INPUT
OUTPUT ENABLE: Enables the device’s outputs through the data
buffers during a read operation. OE# is active low.
WE#
INPUT
WRITE ENABLE: Controls writes to the Command Register and
memory array. WE# is active low. Addresses and data are latched on
the rising edge of the second WE# pulse.
RP#
INPUT
RESET/DEEP POWER-DOWN: Uses two voltage levels (V IL, VIH) to
control reset/deep power-down mode.
When RP# is at logic low, the device is in reset/deep power-down
mode, which drives the outputs to High-Z, resets the Write State
Machine, and minimizes current levels (I CCD).
When RP# is at logic high, the device is in standard operation.
When RP# transitions from logic-low to logic-high, the device resets all
blocks to locked and defaults to the read array mode.
WP#
INPUT
WRITE PROTECT: Controls the lock-down function of the flexible
Locking feature
When WP# is a logic low, the lock-down mechanism is enabled and
blocks marked lock-down cannot be unlocked through software.
When WP# is logic high, the lock-down mechanism is disabled and
blocks previously locked-down are now locked and can be unlocked and
locked through software. After WP# goes low, any blocks previously
marked lock-down revert to that state.
See Section 3.3 for details on block locking.
VCC
SUPPLY
DEVICE POWER SUPPLY: [2.7 V–3.6 V] Supplies power for device
operations.
PRODUCT PREVIEW
9
3 VOLT ADVANCED+ BOOT BLOCK
Table 2. 3 Volt Advanced+ Boot Block Pin Descriptions (Continued)
Symbol
VCCQ
Type
INPUT
E
Name and Function
I/O POWER SUPPLY: Supplies power for input/output buffers.
[2.7 V–3.6 V] This input should be tied directly to V CC.
[1.65 V– 2.5 V] Lower I/O power supply voltage available upon request.
Contact your Intel representative for more information.
VPP
INPUT/
SUPPLY
PROGRAM/ERASE POWER SUPPLY: [1.65 V–3.6 V or 11.4 V–12.6 V]
Operates as a input at logic levels to control complete device protection.
Supplies power for accelerated program and erase operations in 12 V ±
5% range. This pin cannot be left floating.
Lower VPP ≤ VPPLK, to protect all contents against Program and
Erase commands.
Set VPP = VCC for in-system read, program and erase operations. In
this configuration, VPP can drop as low as 1.65 V to allow for resistor or
diode drop from the system supply. Note that if V PP is driven by a logic
signal, VIH = 1.65. That is, V PP must remain above 1.65V to perform insystem flash modifications.
Raise VPP to 12 V ± 5% for faster program and erase in a production
environment. Applying 12 V ± 5% to VPP can only be done for a
maximum of 1000 cycles on the main blocks and 2500 cycles on the
parameter blocks. VPP may be connected to 12 V for a total of 80 hours
maximum. See Section 3.4 for details on V PP voltage configurations.
GND
NC
2.2
SUPPLY
GROUND: For all internal circuitry. All ground inputs must be
connected.
NO CONNECT: Pin may be driven or left floating.
Block Organization
The 3 Volt Advanced+ Boot Block is an
asymmetrically-blocked architecture that enables
system integration of code and data within a single
flash device. Each block can be erased
independently of the others up to 100,000 times.
For the address locations of each block, see the
memory maps in Appendix E and F.
2.2.1
PARAMETER BLOCKS
The 3 Volt Advanced+ Boot Block flash memory
architecture includes parameter blocks to facilitate
storage of frequently updated small parameters
(i.e., data that would normally be stored in an
EEPROM). Each device contains eight parameter
blocks of 8-Kbytes/4-Kwords (8,192 bytes/4,096
words).
2.2.2
MAIN BLOCKS
After the parameter blocks, the remainder of the
array is divided into equal size (64-Kword/32Kword; 65,536 bytes/32,768 words) main blocks for
data or code storage. Each 8-Mbit, 16-Mbit, or
32-Mbit device contains 15, 31, or 63 main blocks,
respectively.
10
PRODUCT PREVIEW
E
3.0
3 VOLT ADVANCED+ BOOT BLOCK
PRINCIPLES OF OPERATION
The 3 Volt Advanced+ Boot Block flash memory
family utilizes a CUI and automated algorithms to
simplify program and erase operations. The CUI
allows for 100% CMOS-level control inputs and
fixed power supplies during erasure and
programming.
The internal WSM completely automates program
and erase operations while the CUI signals the start
of an operation and the status register reports
status. The CUI handles the WE# interface to the
data and address latches, as well as system status
requests during WSM operation.
3.1
Bus Operation
The 3 Volt Advanced+ Boot Block flash memory
devices read, program and erase in-system via the
local CPU or microcontroller. All bus cycles to or
from the flash memory conform to standard
microcontroller bus cycles. Four control pins dictate
the data flow in and out of the flash component:
CE#, OE#, WE# and RP#. These bus operations
are summarized in Table 3.
3.1.1
READ
the VPP voltage. The appropriate read mode
command must be issued to the CUI to enter the
corresponding mode. Upon initial device power-up
or after exit from reset, the device automatically
defaults to read array mode.
CE# and OE# must be driven active to obtain data
at the outputs. CE# is the device selection control;
when active it enables the flash memory device.
OE# is the data output control and it drives the
selected memory data onto the I/O bus. For all read
modes, WE# and RP# must be at VIH. Figure 9
illustrates a read cycle.
3.1.2
OUTPUT DISABLE
With OE# at a logic-high level (VIH), the device
outputs are disabled. Output pins are placed in a
high-impedance state.
3.1.3
STANDBY
Deselecting the device by bringing CE# to a logichigh level (VIH) places the device in standby mode,
which substantially reduces device power
consumption without any latency for subsequent
read accesses. In standby, outputs are placed in a
high-impedance state independent of OE#. If
deselected during program or erase operation, the
device continues to consume active power until the
program or erase operation is complete.
The flash memory has four read modes available:
read array, read configuration, read status and read
query. These modes are accessible independent of
Table 3. Bus Operations(1)
Mode
Read (Array, Status,
Configuration, or Query)
Note
RP#
CE#
OE#
WE#
DQ0–7
DQ8-15
2-4
VIH
VIL
VIL
VIH
DOUT
DOUT
2
VIH
VIL
VIH
VIH
High Z
High Z
Output Disable
Standby
2
VIH
VIH
X
X
High Z
High Z
Reset
2,7
VIL
X
X
X
High Z
High Z
Write
2,5-7
VIH
VIL
VIH
VIL
DIN
DIN
NOTES:
1. 8-bit devices use only DQ[0:7], 16-bit devices use DQ[0:15]
2. X must be VIL, VIH for control pins and addresses.
3. See DC Characteristics for VPPLK, VPP1, VPP2, VPP3, voltages.
4. Manufacturer and device codes may also be accessed in read configuration mode (A1–A20 = 0). See Table 4.
5. Refer to Table 5 for valid DIN during a write operation.
6. To program or erase the lockable blocks, hold WP# at VIH.
7. RP# must be at GND ± 0.2 V to meet the maximum deep power-down current specified.
PRODUCT PREVIEW
11
E
3 VOLT ADVANCED+ BOOT BLOCK
3.1.4
RESET
From read mode, RP# at VIL for time tPLPH
deselects the memory, places output drivers in a
high-impedance state, and turns off all internal
circuits. After return from reset, a time tPHQV is
required until the initial read access outputs are
valid. A delay (tPHWL or tPHEL) is required after
return from reset before a write can be initiated.
After this wake-up interval, normal operation is
restored. The CUI resets to read array mode, and
the status register is set to 80H. This case is shown
in Figure 11A.
If RP# is taken low for time tPLPH during a program
or erase operation, the operation will be aborted
and the memory contents at the aborted location
(for a program) or block (for an erase) are no longer
valid, since the data may be partially erased or
written. The abort process goes through the
following sequence: When RP# goes low, the
device shuts down the operation in progress, a
process which takes time tPLRH to complete. After
this time tPLRH, the part will either reset to read
array mode (if RP# has gone high during tPLRH,
Figure 11B) or enter reset mode (if RP# is still logic
low after tPLRH, Figure 11C). In both cases, after
returning from an aborted operation, the relevant
time tPHQV or tPHWL/tPHEL must be waited before a
read or write operation is initiated, as discussed in
the previous paragraph. However, in this case,
these delays are referenced to the end of tPLRH
rather than when RP# goes high.
addressable memory location. The address and
data buses are latched on the rising edge of the
second WE# or CE# pulse, whichever occurs first.
Figure 10 illustrates a program and erase operation.
The available commands are shown in Table 6, and
Appendix A provides detailed information on
moving between the different modes of operation
using CUI commands.
There are two commands that modify array data:
Program (40H) and Erase (20H). Writing either of
these commands to the internal Command User
Interface (CUI) initiates a sequence of internallytimed functions that culminate in the completion of
the requested task (unless that operation is aborted
by either RP# being driven to VIL for tPLRH or an
appropriate suspend command).
3.2
Modes of Operation
The flash memory has four read modes and two
write modes. The read modes are read array, read
configuration, read status, and read query. The
write modes are program and block erase. Three
additional modes (erase suspend to program, erase
suspend to read and program suspend to read) are
available only during suspended operations. These
modes are reached using the commands
summarized in Tables 5 and 6. A comprehensive
chart showing the state transitions is in Appendix A.
3.2.1
As with any automated device, it is important to
assert RP# during system reset. When the system
comes out of reset, processor expects to read from
the flash memory. Automated flash memories
provide status information when read during
program or block erase operations. If a CPU reset
occurs with no flash memory reset, proper CPU
initialization may not occur because the flash
memory may be providing status information
instead of array data. Intel’s flash memories allow
proper CPU initialization following a system reset
through the use of the RP# input. In this application,
RP# is controlled by the same RESET# signal that
resets the system CPU.
3.1.5
WRITE
A write takes place when both CE# and WE# are
low and OE# is high. Commands are written to the
Command User Interface (CUI) using standard
microprocessor write timings to control flash
operations. The CUI does not occupy an
12
READ ARRAY
When RP# transitions from VIL (reset) to VIH, the
device defaults to read array mode and will respond
to the read control inputs (CE#, address inputs, and
OE#) without any additional CUI commands.
When the device is in read array mode, four control
signals control data output:
•
WE# must be logic high (VIH)
•
CE# must be logic low (VIL)
•
OE# must be logic low (VIL)
•
RP# must be logic high (VIH)
In addition, the address of the desired location must
be applied to the address pins. If the device is not
in read array mode, as would be the case after a
program or erase operation, the Read Array
command (FFH) must be written to the CUI before
array reads can take place.
PRODUCT PREVIEW
E
3.2.2
3 VOLT ADVANCED+ BOOT BLOCK
READ CONFIGURATION
The Read Configuration mode outputs the
manufacturer/device identifier. The device is
switched to this mode by writing the Read
Configuration command (90H). Once in this mode,
read cycles from addresses shown in Table 4
retrieve the specified information. To return to read
array mode, write the Read Array command (FFH).
The Read Configuration mode outputs three types
of information: the manufacturer/device identifier,
the block locking status, and the protection register.
The device is switched to this mode by writing the
Read Configuration command (90H). Once in this
mode, read cycles from addresses shown in Table
4 retrieve the specified information. To return to
read array mode, write the Read Array command
(FFH).
Table 4. Read Configuration Table
Item
command causes subsequent reads to output data
from the status register until another command is
issued. To return to reading from the array, issue a
Read Array (FFH) command.
The status register bits are output on DQ0–DQ7.
The upper byte, DQ8–DQ15, outputs 00H during a
Read Status Register command.
The contents of the status register are latched on
the falling edge of OE# or CE#, whichever occurs
last. This prevents possible bus errors which might
occur if status register contents change while being
read. CE# or OE# must be toggled with each
subsequent status read, or the status register will
not indicate completion of a program or erase
operation.
When the WSM is active, SR.7 will indicate the
status of the WSM; the remaining bits in the status
register indicate whether the WSM was successful
in performing the desired operation (see Table 7).
Address
Data
Manufacturer Code (x16)
00000
0089
Manufacturer Code (x8)
00000
89
3.2.3.1
Device ID (See Appendix G)
00001
ID
XX002(1)
LOCK
The WSM sets status bits 1 through 7 to “1,” and
clears bits 2, 6 and 7 to “0,” but cannot clear status
bits 1 or 3 through 5 to “0.” Because bits 1, 3, 4 and
5 indicate various error conditions, these bits can
only be cleared through the use of the Clear Status
Register (50H) command. By allowing the system
software to control the resetting of these bits,
several operations may be performed (such as
cumulatively programming several addresses or
erasing multiple blocks in sequence) before reading
the status register to determine if an error occurred
during that series. Clear the Status Register before
beginning another command or sequence. Note
that the Read Array command must be issued
before data can be read from the memory array.
Resetting the device also clears the status register.
Block Lock Configuration2
• Block Is Unlocked
DQ0 = 0
• Block Is Locked
DQ0 = 1
• Block Is Locked-Down
DQ1 = 1
Protection Register Lock3
80
PR-LK
Protection Register (x16)
81-88
PR
Protection Register (x8)
(App. H)
PR
NOTES:
1. “XX” specifies the block address of lock configuration
being read.
2. See Section 3.3.4 for valid lock status outputs.
3. See Section 3.4 for protection register information.
4. Other locations within the configuration address space
are reserved by Intel for future use.
3.2.3
READ STATUS REGISTER
The status register indicates the status of device
operations, and the success/failure of that
operation. The Read Status Register (70H)
PRODUCT PREVIEW
3.2.4
Clearing the Status Register
READ QUERY
The Read Query mode outputs Common Flash
Interface (CFI) data when the device is read. This
can be accessed by writing the Read Query
Command (98H). The CFI data structure contains
information such as block size, density, command
set and electrical specifications. Once in this mode,
read cycles from addresses shown in Appendix C
retrieve the specified information. To return to read
array mode, write the Read Array command (FFH).
13
E
3 VOLT ADVANCED+ BOOT BLOCK
3.2.5
PROGRAM MODE
Programming is executed using a two-write
sequence. The Program Setup command (40H) is
written to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute a sequence of internally
timed events to program desired bits of the
addressed location, then verify the bits are
sufficiently programmed. Programming the memory
results in specific bits within an address location
being changed to a “0.” If the user attempts to
program “1”s, the memory cell contents do not
change and no error occurs.
The status register indicates programming status:
while the program sequence executes, status bit 7
is “0.” The status register can be polled by toggling
either CE# or OE#. While programming, the only
valid commands are Read Status Register,
Program Suspend, and Program Resume.
When programming is complete, the Program
Status bits should be checked. If the programming
operation was unsuccessful, bit SR.4 of the status
register is set to indicate a program failure. If SR.3
is set then VPP was not within acceptable limits, and
the WSM did not execute the program command. If
SR.1 is set, a program operation was attempted on
a locked block and the operation was aborted.
The status register should be cleared before
attempting the next operation. Any CUI instruction
can follow after programming is completed;
however, to prevent inadvertent status register
reads, be sure to reset the CUI to read array mode.
3.2.5.1
Suspending and Resuming
Program
The Program Suspend command halts an inprogress program operation so that data can be
read from other locations of memory. Once the
programming process starts, writing the Program
Suspend command to the CUI requests that the
WSM suspend the program sequence (at
predetermined points in the program algorithm).
The device continues to output status register data
after the Program Suspend command is written.
Polling status register bits SR.7 and SR.2 will
determine when the program operation has been
suspended (both will be set to “1”). tWHRH1/tEHRH1
specify the program suspend latency.
14
A Read Array command can now be written to the
CUI to read data from blocks other than that which
is suspended. The only other valid commands,
while program is suspended, are Read Status
Register, Read Configuration, Read Query, and
Program Resume. After the Program Resume
command is written to the flash memory, the WSM
will continue with the programming process and
status register bits SR.2 and SR.7 will automatically
be cleared. The device automatically outputs status
register data when read (see Figure 13 in Appendix
B, Program Suspend/Resume Flowchart) after the
Program Resume command is written. VPP must
remain at the same VPP level used for program
while in program suspend mode. RP# must also
remain at VIH.
3.2.6
ERASE MODE
To erase a block, write the Erase Set-up and Erase
Confirm commands to the CUI, along with an
address identifying the block to be erased. This
address is latched internally when the Erase
Confirm command is issued. Block erasure results
in all bits within the block being set to “1.” Only one
block can be erased at a time. The WSM will
execute a sequence of internally timed events to
program all bits within the block to “0,” erase all bits
within the block to “1,” then verify that all bits within
the block are sufficiently erased. While the erase
executes, status bit 7 is a “0.”
When the status register indicates that erasure is
complete, check the erase status bit to verify that
the erase operation was successful. If the Erase
operation was unsuccessful, SR.5 of the status
register will be set to a “1,” indicating an erase
failure. If VPP was not within acceptable limits after
the Erase Confirm command was issued, the WSM
will not execute the erase sequence; instead, SR.5
of the status register is set to indicate an erase
error, and SR.3 is set to a “1” to identify that VPP
supply voltage was not within acceptable limits.
After an erase operation, clear the status register
(50H) before attempting the next operation. Any
CUI instruction can follow after erasure is
completed; however, to prevent inadvertent status
register reads, it is advisable to place the flash in
read array mode after the erase is complete.
PRODUCT PREVIEW
E
3.2.6.1
3 VOLT ADVANCED+ BOOT BLOCK
Suspending and Resuming Erase
A Read Array/Program command can now be
written to the CUI to read/program data from/to
blocks other than that which is suspended. This
nested Program command can subsequently be
suspended to read yet another location. The only
valid commands while erase is suspended are
Read Status Register, Read Configuration, Read
Query, Program Setup, Program Resume, Erase
Resume, Lock Block, Unlock Block and Lock-Down
Block. During erase suspend mode, the chip can be
placed in a pseudo-standby mode by taking CE# to
VIH. This reduces active current consumption.
Since an erase operation requires on the order of
seconds to complete, an Erase Suspend command
is provided to allow erase-sequence interruption in
order to read data from or program data to another
block in memory. Once the erase sequence is
started, writing the Erase Suspend command to the
CUI suspends the erase sequence at a
predetermined point in the erase algorithm. The
status register will indicate if/when the erase
operation has been suspended. Erase suspend
latency is specified by t WHRH2/tEHRH2.
Erase Resume continues the erase sequence when
CE# = VIL. As with the end of a standard erase
operation, the status register must be read and
cleared before the next instruction is issued.
Table 5. Command Bus Definitions
First Bus Cycle
Command
Second Bus Cycle
Notes
Oper
Addr
Data
4
Write
X
FFH
Read Configuration
2, 4
Write
X
90H
Read
IA
ID
Read Query
2, 4
Write
X
98H
Read
QA
QD
4
Write
X
70H
Read
X
SRD
Read Array
Read Status Register
Clear Status Register
Oper
Addr
Data
4
Write
X
50H
3,4
Write
X
40H/10H
Write
PA
PD
Block Erase/Confirm
4
Write
X
20H
Write
BA
D0H
Program/Erase Suspend
4
Write
X
B0H
Program/Erase Resume
4
Write
X
D0H
Lock Block
4
Write
X
60H
Write
BA
01H
Unlock Block
4
Write
X
60H
Write
BA
D0H
Lock-Down Block
4
Write
X
60H
Write
BA
2FH
4
Write
X
C0H
Write
PA
PD
Program
Protection Program
X = Don’t Care
SRD = Status Reg. Data
PA = Prog Addr BA = Block Addr
PD = Prog Data
IA = Identifier Addr.
ID = Identifier Data
QA = Query Addr.
QD = Query Data
NOTES:
1. Bus operations are defined in Table 3.
2. Following the Read Configuration or Read Query commands, read operations output device configuration or CFI query
information, respectively. See Section 3.2.2 and 3.2.4.
3. Either 40H or 10H command is valid, but the Intel standard is 40H.
4. When writing commands, the upper data bus [DQ8–DQ15] should be either VIL or VIH, to minimize current draw.
PRODUCT PREVIEW
15
E
3 VOLT ADVANCED+ BOOT BLOCK
Table 6. Command Codes and Descriptions
Code
Device Mode
FF
Read Array
40
Program
Set-Up
20
Erase
Set-Up
Prepares the CUI for the Erase Confirm command. If the next command is not
an Erase Confirm command, then the CUI will (a) set both SR.4 and SR.5 of the
status register to a “1,” (b) place the device into the read status register mode,
and (c) wait for another command. See Section 3.2.6.
D0
Erase Confirm
If the previous command was an Erase Set-Up command, then the CUI will
close the address and data latches, and begin erasing the block indicated on the
address pins. During program/erase, the device will respond only to the Read
Status Register, Program Suspend and Erase Suspend commands and will
output status register data when CE# or OE# is toggled.
Program/Erase
Resume
If a program or erase operation was previously suspended, this command will
resume that operation.
B0
Places device in read array mode, such that array data will be output on the
data pins.
This is a two-cycle command. The first cycle prepares the CUI for a program
operation. The second cycle latches addresses and data information and
initiates the WSM to execute the Program algorithm. The flash outputs status
register data when CE# or OE# is toggled. A Read Array command is required
after programming to read array data. See Section 3.2.5.
Unlock Block
If the previous command was Configuration Set-Up, the CUI will latch the
address and unlock the block indicated on the address pins. If the block had
been previously set to Lock-Down, this operation will have no effect. (Sect. 3.3)
Program
Suspend
Issuing this command will begin to suspend the currently executing
program/erase operation. The status register will indicate when the operation
has been successfully suspended by setting either the program suspend (SR.2)
or erase suspend (SR.6) and the WSM Status bit (SR.7) to a “1” (ready). The
WSM will continue to idle in the SUSPEND state, regardless of the state of all
input control pins except RP#, which will immediately shut down the WSM and
the remainder of the chip if RP# is driven to V IL. See Sections 3.2.5.1 and
3.2.6.1.
Erase
Suspend
16
Description
70
Read Status
Register
This command places the device into read status register mode. Reading the
device will output the contents of the status register, regardless of the address
presented to the device. The device automatically enters this mode after a
program or erase operation has been initiated. See Section 3.2.3.
50
Clear Status
Register
The WSM can set the Block Lock Status (SR.1) , V PP Status (SR.3), Program
Status (SR.4), and Erase Status (SR.5) bits in the status register to “1,” but it
cannot clear them to “0.” Issuing this command clears those bits to “0.”
90
Read
Configuration
Puts the device into the Read Configuration mode, so that reading the device
will output the manufacturer/device codes or block lock status. Section 3.2.2.
60
Configuration
Set-Up
Prepares the CUI for changes to the device configuration, such as block locking
changes. If the next command is not Block Unlock, Block Lock, or Block LockDown, then the CUI will set both the Program and Erase Status register bits to
indicate a command sequence error. See Section 3.3.
01
Lock-Block
If the previous command was Configuration Set-Up, the CUI will latch the
address and lock the block indicated on the address pins. (Section 3.3)
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Table 6. Command Codes and Descriptions (Continued)
Code
Device Mode
2F
Lock-Down
98
Read
Query
Puts the device into the Read Query mode, so that reading the device will
output Common Flash Interface information. See Section 3.2.4 and Appendix C.
C0
Protection
Program
Setup
This is a two-cycle command. The first cycle prepares the CUI for an program
operation to the Protection Register. The second cycle latches addresses and
data information and initiates the WSM to execute the Protection Program
algorithm to the Protection Register. The flash outputs status register data when
CE# or OE# is toggled. A Read Array command is required after programming
to read array data. See Section 3.4.
10
00
Description
If the previous command was a Configuration Set-Up command, the CUI will
latch the address and lock-down the block indicated on the address pins.
(Section 3.3)
Alt. Prog Set-Up Operates the same as Program Set-up command. (See 40H/Program Set-Up)
Invalid/
Reserved
Unassigned commands that should not be used. Intel reserves the right to
redefine these codes for future functions.
NOTE:
See Appendix A for mode transition information.
PRODUCT PREVIEW
17
E
3 VOLT ADVANCED+ BOOT BLOCK
Table 7. Status Register Bit Definition
WSMS
ESS
ES
PS
VPPS
PSS
BLS
R
7
6
5
4
3
2
1
0
NOTES:
SR.7 WRITE STATE MACHINE STATUS
1 = Ready
(WSMS)
0 = Busy
Check Write State Machine bit first to determine Word
Program or Block Erase completion, before checking
Program or Erase Status bits.
SR.6 = ERASE-SUSPEND STATUS (ESS)
1 = Erase Suspended
0 = Erase In Progress/Completed
When Erase Suspend is issued, WSM halts execution
and sets both WSMS and ESS bits to “1.” ESS bit
remains set to “1” until an Erase Resume command is
issued.
SR.5 = ERASE STATUS (ES)
1 = Error In Block Erase
0 = Successful Block Erase
When this bit is set to “1,” WSM has applied the max.
number of erase pulses to the block and is still unable to
verify successful block erasure.
SR.4 = PROGRAM STATUS (PS)
1 = Error in Programming
0 = Successful Programming
When this bit is set to “1,” WSM has attempted but failed
to program a word/byte.
SR.3 = VPP STATUS (VPPS)
1 = VPP Low Detect, Operation Abort
0 = VPP OK
The VPP status bit does not provide continuous indication
of VPP level. The WSM interrogates VPP level only after
the Program or Erase command sequences have been
entered, and informs the system if V PP has not been
switched on. The VPP is also checked before the
operation is verified by the WSM. The V PP status bit is
not guaranteed to report accurate feedback between
VPPLK and VPP1Min.
SR.2 = PROGRAM SUSPEND STATUS
(PSS)
1 = Program Suspended
0 = Program in Progress/Completed
When Program Suspend is issued, WSM halts execution
and sets both WSMS and PSS bits to “1.” PSS bit
remains set to “1” until a Program Resume command is
issued.
SR.1 = BLOCK LOCK STATUS
1 = Prog/Erase attempted on a locked
block; Operation aborted.
0 = No operation to locked blocks
If a program or erase operation is attempted to one of the
locked blocks, this bit is set by the WSM. The operation
specified is aborted and the device is returned to read
status mode.
SR.0 = RESERVED FOR FUTURE
ENHANCEMENTS (R)
This bit is reserved for future use and should be masked
out when polling the status register.
18
PRODUCT PREVIEW
E
3.3
Flexible Block Locking
The Intel® 3 Volt Advanced+ Boot Block products
offer an instant, individual block locking scheme
that allows any block to be locked or unlocked with
no latency, enabling instant code and data
protection.
This locking scheme offers two levels of protection.
The first level allows software-only control of block
locking (useful for data blocks that change
frequently), while the second level requires
hardware interaction before locking can be changed
(useful for code blocks that change infrequently).
The following sections will discuss the operation of
the locking system. The term “state [XYZ]” will be
used to specify locking states; e.g., “state [001],”
where X = value of WP#, Y = bit DQ1 of the Block
Lock status register, and Z = bit DQ0 of the Block
Lock status register. Table 9 defines all of these
possible locking states.
3.3.1
3 VOLT ADVANCED+ BOOT BLOCK
3.3.2
LOCKED STATE
The default status of all blocks upon power-up or
reset is locked (states [001] or [101]). Locked
blocks are fully protected from alteration. Any
program or erase operations attempted on a locked
block will return an error on bit SR.1 of the status
register. The status of a locked block can be
changed to Unlocked or Lock-Down using the
appropriate software commands. An Unlocked
block can be locked by writing the Lock command
sequence, 60H followed by 01H.
3.3.3
UNLOCKED STATE
Unlocked blocks (states [000], [100], [110]) can be
programmed or erased. All unlocked blocks return
to the Locked state when the device is reset or
powered down. The status of an unlocked block can
be changed to Locked or Locked-Down using the
appropriate software commands. A Locked block
can be unlocked by writing the Unlock command
sequence, 60H followed by D0H.
LOCKING OPERATION
The following concisely summarizes the locking
functionality.
•
All blocks power-up locked, then can be
unlocked or locked with the Unlock and Lock
commands.
•
The Lock-Down command locks a block and
prevents it from being unlocked when WP# = 0.
 When WP# = 1, Lock-Down is overridden
and commands can unlock/lock lockeddown blocks.
 When WP# returns to 0, locked-down
blocks return to Lock-Down.
 Lock-Down is cleared only when the device
is reset or powered-down.
The locking status of each block can set to Locked,
Unlocked, and Lock-Down, each of which will be
described
in
the
following
sections.
A
comprehensive state table for the locking functions
is shown in Table 9, and a flowchart for locking
operations is shown in Figure 16.
PRODUCT PREVIEW
3.3.4
LOCK-DOWN STATE
Blocks that are Locked-Down (state [011]) are
protected from program and erase operations (just
like Locked blocks), but their protection status
cannot be changed using software commands
alone. A Locked or Unlocked block can be Lockeddown by writing the Lock-Down command
sequence, 60H followed by 2FH. Locked-Down
blocks revert to the Locked state when the device is
reset or powered down.
The Lock-Down function is dependent on the WP#
input pin. When WP# = 0, blocks in Lock-Down
[011] are protected from program, erase, and lock
status changes. When WP# = 1, the Lock-Down
function is disabled ([111]) and locked-down blocks
can be individually unlocked by software command
to the [110] state, where they can be erased and
programmed. These blocks can then be relocked
[111] and unlocked [110] as desired while WP#
remains high. When WP# goes low, blocks that
were previously locked-down return to the
Lock-Down state [011] regardless of any changes
made while WP# was high. Device reset or powerdown resets all blocks, including those in LockDown, to Locked state.
19
E
3 VOLT ADVANCED+ BOOT BLOCK
3.3.5
READING A BLOCK’S LOCK STATUS
The lock status of every block can be read in the
Configuration Read mode of the device. To enter
this mode, write 90H to the device. Subsequent
reads at Block Address + 00002 will output the lock
status of that block. The lock status is represented
by the lowest two output pins, DQ0 and DQ1. DQ0
indicates the Block Lock/Unlock status and is set by
the Lock command and cleared by the Unlock
command. It is also automatically set when entering
Lock-Down. DQ1 indicates Lock-Down status and is
set by the Lock-Down command. It cannot be
cleared by software, only by device reset or powerdown.
Table 8. Block Lock Status
Item
Address
Block Lock Configuration
XX002
Data
DQ0 = 0
• Block Is Locked
DQ0 = 1
• Block Is Locked-Down
DQ1 = 1
LOCKING OPERATIONS DURING
ERASE SUSPEND
Changes to block lock status can be performed
during an erase suspend by using the standard
locking command sequences to unlock, lock, or
lock-down a block. This is useful in the case when
another block needs to be updated while an erase
operation is in progress.
To change block locking during an erase operation,
first write the erase suspend command (B0H), then
check the status register until it indicates that the
erase operation has been suspended. Next write
the desired lock command sequence to a block and
20
If a block is locked or locked-down during a
suspended erase of the same block, the locking
status bits will be changed immediately, but when
the erase is resumed, the erase operation will
complete.
Locking operations cannot be performed during a
program suspend. Refer to Appendix A for detailed
information on which commands are valid during
erase suspend.
3.3.7
STATUS REGISTER ERROR
CHECKING
LOCK
• Block Is Unlocked
3.3.6
the lock status will be changed. After completing
any desired lock, read, or program operations,
resume the erase operation with the Erase Resume
command (D0H).
Using nested locking or program command
sequences during erase suspend can introduce
ambiguity into status register results.
Since locking changes are performed using a two
cycle command sequence, e.g., 60H followed by
01H to lock a block, following the Configuration
Setup command (60H) with an invalid command will
produce a lock command error (SR.4 and SR.5 will
be set to 1) in the status register. If a lock
command error occurs during an erase suspend,
SR.4 and SR.5 will be set to 1, and will remain at 1
after the erase is resumed. When erase is
complete, any possible error during the erase
cannot be detected via the status register because
of the previous locking command error.
A similar situation happens if an error occurs during
a program operation error nested within an erase
suspend.
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Table 9. Block Locking State Transitions
Current State
Erase/Prog
Lock Command Input Result [Next State]
WP#
DQ1
DQ0
Name
Allowed?
Lock
Unlock
Lock-Down
0
0
0
“Unlocked”
Yes
Goes To [001]
No Change
Goes To [011]
0
0
1
“Locked” (Default)
No
No Change
0
1
1
“Locked-Down”
No
No Change
No Change
No Change
1
0
0
“Unlocked”
Yes
Goes To [101]
No Change
Goes To [111]
1
0
1
“Locked”
No
No Change
1
1
0
Lock-Down Disabled
Yes
Goes To [111]
No Change
Goes To [111]
1
1
1
Lock-Down Disabled
No
No Change
Goes To [110]
No Change
Goes To [000] Goes To [011]
Goes To [100] Goes To [111]
NOTES:
1. In this table, the notation [XYZ] denotes the locking state of a block, where X = WP#, Y = DQ1, and Z = DQ0. The current
locking state of a block is defined by the state of WP# and the two bits of the block lock status (DQ0, DQ1). DQ0 indicates if
a block is locked (1) or unlocked (0). DQ1 indicates if a block has been locked-down (1) or not (0).
2. At power-up or device reset, all blocks default to Locked state [001] (if WP# = 0). Holding WP# = 0 is the recommended
default.
3. The “Erase/Program Allowed?” column shows whether erase and program operations are enabled (Yes) or disabled (No)
in that block’s current locking state.
4. The “Lock Command Input Result [Next State]” column shows the result of writing the three locking commands (Lock,
Unlock, Lock-Down) in the current locking state. For example, “Goes To [001]” would mean that writing the command to a
block in the current locking state would change it to [001].
3.4
128-Bit Protection Register
The Advanced+ Boot Block architecture includes a
128-bit protection register than can be used to
increase the security of a system design. For
example, the number contained in the protection
register can be used to “mate” the flash component
with other system components such as the CPU or
ASIC, preventing device substitution. Additional
application information can be found in Intel
application note AP-657 Designing with the
Advanced+ Boot Block Flash Memory Architecture .
The 128-bits of the protection register are divided
into two 64-bit segments. One of the segments is
programmed at the Intel factory with a unique 64-bit
number, which is unchangeable. The other segment
is left blank for customer designs to program as
desired. Once the customer segment is
programmed, it can be locked to prevent
reprogramming.
PRODUCT PREVIEW
3.4.1
READING THE PROTECTION
REGISTER
The protection register is read in the configuration
read mode. The device is switched to this mode by
writing the Read Configuration command (90H).
Once in this mode, read cycles from addresses
shown in Appendix H retrieve the specified
information. To return to read array mode, write the
Read Array command (FFH).
3.4.2
PROGRAMMING THE PROTECTION
REGISTER
The protection register bits are programmed using
the two-cycle Protection Program command. The
64-bit number is programmed 16 bits at a time for
word-wide parts and eight bits at a time for bytewide parts. First write the Protection Program Setup
command, C0H. The next write to the device will
latch in address and data and program the specified
location. The allowable addresses are shown in
Appendix H. See Figure 17 for the Protection
Register Programming Flowchart.
21
E
3 VOLT ADVANCED+ BOOT BLOCK
Any attempt to address Protection Program
commands outside the defined protection register
address space will result in a Status Register error
(Program Error bit SR.4 will be set to 1). Attempting
to program or to a previously locked protection
register segment will result in a status register error
(program error bit SR.4 and lock error bit SR.1 will
be set to 1).
3.5.1
3.4.3
When VPP is between 1.65 V and 3.6 V, all program
and erase current is drawn through the VCC pin.
Note that if VPP is driven by a logic signal,
VIH = 1.65 V. That is, VPP must remain above 1.65 V
to perform in-system flash modifications. When VPP
is connected to a 12 V power supply, the device
draws program and erase current directly from the
VPP pin. This eliminates the need for an external
switching transistor to control the voltage VPP.
Figure 6 shows examples of how the flash power
supplies can be configured for various usage
models.
LOCKING THE PROTECTION
REGISTER
The user-programmable segment of the protection
register is lockable by programming Bit 1 of the
PR-LOCK location to 0. Bit 0 of this location is
programmed to 0 at the Intel factory to protect the
unique device number. This bit is set using the
Protection Program command to program “FFFD” to
the PR-LOCK location. After these bits have been
programmed, no further changes can be made to
the values stored in the protection register.
Protection Program commands to a locked section
will result in a status register error (Program Error
bit SR.4 and Lock Error bit SR.1 will be set to 1).
Protection register lockout state is not reversible.
88H
4 Words
User Programmed
85H
84H
81H
80H
Intel’s 3 Volt Advanced+ Boot Block products
provide in-system programming and erase in the
2.7 V–3.6 V
range.
For
fast
production
programming, 3 Volt Advanced+ Boot Block
includes a low-cost, backward-compatible 12 V
programming feature.
The 12 V VPP mode enhances programming
performance during the short period of time typically
found in manufacturing processes; however, it is
not intended for extended use. 12 V may be applied
to VPP during program and erase operations for a
maximum of 1000 cycles on the main blocks and
2500 cycles on the parameter blocks. VPP may be
connected to 12 V for a total of 80 hours maximum.
Stressing the device beyond these limits may cause
permanent damage.
3.5.2
4 Words
Factory Programmed
1 Word Lock
0645_05
EASY-12 V OPERATION FOR FAST
MANUFACTURING PROGRAMMING
VPP ≤ VPPLK FOR COMPLETE
PROTECTION
In addition to the flexible block locking, the VPP
programming voltage can be held low for absolute
hardware write protection of all blocks in the flash
device. When VPP is below VPPLK, any program or
erase operation will result in a error, prompting the
corresponding status register bit (SR.3) to be set.
Figure 5. Protection Register Memory Map
3.5.3
3.5
VPP Program and Erase
Voltages
Intel’s 3 Volt Advanced+ Boot Block products
provide in-system writes plus a VPP pin for 12 V
production programming and complete write
protection.
22
VPP USAGE
The VPP pin is used for two functions: Absolute data
protection and fast production programming.
When VPP ≤ VPPLK, then all program or erase
operations to the device are inhibited, providing
absolute data protection.
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
System Supply
System Supply
12 V Supply
VCC
VCC
VPP
10 KΩ
Prot#
(Logic Signal)
VPP
12 V Fast Programming
Low-Voltage Programming Only
Complete Write Protection When V PP ≠ 12 V
Logic Control of Complete Device Protection
System Supply
(Note 1)
System Supply
VCC
VCC
VPP
VPP
12 V Supply
12 V Fast Programming
Low-Voltage Programming Only
Full Array Protection Unavailable
Full Array Protection Unavailable
0645_06
NOTE:
1. A resistor can be used if the VCC supply can sink adequate current based on resistor value. See AP-657 Designing with
the Advanced+ Boot Block Flash Memory Architecture for details.
Figure 6. Example Power Supply Configurations
When VPP is raised to 12 V, such as in a
manufacturing situations, the device directly applies
the high voltage to achieve faster program and
erase.
Designing for in-system writes to the flash memory
requires special consideration of power supply
traces by the printed circuit board designer.
Adequate power supply traces, and decoupling
capacitors placed adjacent to the component, will
decrease spikes and overshoots.
3.6
Power Consumption
Intel’s flash devices have a tiered approach to
power savings that can significantly reduce overall
system power consumption. The Automatic Power
Savings (APS) feature reduces power consumption
when the device is selected but idle. If the CE# is
deasserted, the flash enters its standby mode,
where current consumption is even lower. The
combination of these features can minimize
memory power consumption, and therefore, overall
system power consumption.
3.6.1
ACTIVE POWER
(Program/Erase/Read)
With CE# at a logic-low level and RP# at a logichigh level, the device is in the active mode. Refer to
the DC Characteristic tables for ICC current values.
Active power is the largest contributor to overall
system power consumption. Minimizing the active
current could have a profound effect on system
power consumption, especially for battery-operated
devices.
3.6.2
AUTOMATIC POWER SAVINGS (APS)
Automatic Power Savings provides low-power
operation during read mode. After data is read from
the memory array and the address lines are
quiescent, APS circuitry places the device in a
mode where typical current is comparable to ICCS.
The flash stays in this static state with outputs valid
until a new location is read.
3.6.3
STANDBY POWER
With CE# at a logic-high level (VIH) and device in
read mode, the flash memory is in standby mode,
which disables much of the device’s circuitry and
PRODUCT PREVIEW
23
E
3 VOLT ADVANCED+ BOOT BLOCK
substantially reduces power consumption. Outputs
are placed in a high-impedance state independent
of the status of the OE# signal. If CE# transitions to
a logic-high level during erase or program
operations, the device will continue to perform the
operation and consume corresponding active power
until the operation is completed.
System engineers should analyze the breakdown of
standby time versus active time and quantify the
respective power consumption in each mode for
their specific application. This will provide a more
accurate measure of application-specific power and
energy requirements.
3.6.4
DEEP POWER-DOWN MODE
The deep power-down mode is activated when
RP# = VIL (GND ± 0.2 V). During read modes, RP#
going low de-selects the memory and places the
outputs in a high impedance state. Recovery from
deep power-down requires a minimum time of tPHQV
for read operations and tPHWL/tPHEL for write
operations.
During program or erase modes, RP# transitioning
low will abort the in-progress operation. The
memory contents of the address being programmed
or the block being erased are no longer valid as the
data integrity has been compromised by the abort.
During deep power-down, all internal circuits are
switched to a low power savings mode (RP#
transitioning to VIL or turning off power to the device
clears the status register).
proper CPU/flash initialization following system
reset.
System designers must guard against spurious
writes when VCC voltages are above VLKO. Since
both WE# and CE# must be low for a command
write, driving either signal to VIH will inhibit writes to
the device. The CUI architecture provides additional
protection since alteration of memory contents can
only occur after successful completion of the twostep command sequences. The device is also
disabled until RP# is brought to VIH, regardless of
the state of its control inputs. By holding the device
in reset (RP# connected to system PowerGood)
during power-up/down, invalid bus conditions during
power-up can be masked, providing yet another
level of memory protection.
3.7.2
The CUI latches commands as issued by system
software and is not altered by VPP or CE#
transitions or WSM actions. Its default state upon
power-up, after exit from reset mode or after VCC
transitions above VLKO (Lockout voltage), is read
array mode.
After any program or block erase operation is
complete (even after VPP transitions down to
VPPLK), the CUI must be reset to read array mode
via the Read Array command if access to the flash
memory array is desired.
3.8
3.7
Power-Up/Down Operation
The device is protected against accidental block
erasure or programming during power transitions.
Power supply sequencing is not required, since the
device is indifferent as to which power supply, VPP
or VCC, powers-up first.
3.7.1
RP# CONNECTED TO SYSTEM
RESET
The use of RP# during system reset is important
with automated program/erase devices since the
system expects to read from the flash memory
when it comes out of reset. If a CPU reset occurs
without a flash memory reset, proper CPU
initialization will not occur because the flash
memory may be providing status information
instead of array data. Intel recommends connecting
RP# to the system CPU RESET# signal to allow
24
VCC, VPP AND RP# TRANSITIONS
Power Supply Decoupling
Flash memory’s power switching characteristics
require careful device decoupling. System
designers should consider three supply current
issues:
1. Standby current levels (ICCS)
2. Read current levels (ICCR)
3. Transient peaks produced by falling and rising
edges of CE#.
Transient current magnitudes depend on the device
outputs’ capacitive and inductive loading. Two-line
control and proper decoupling capacitor selection
will suppress these transient voltage peaks. Each
flash device should have a 0.1 µF ceramic
capacitor connected between each VCC and GND,
and between its VPP and GND. These highfrequency, inherently low-inductance capacitors
should be placed as close as possible to the
package leads.
PRODUCT PREVIEW
E
4.0
3 VOLT ADVANCED+ BOOT BLOCK
ABSOLUTE MAXIMUM
RATINGS*
Extended Operating Temperature
During Read .......................... –40 °C to +85 °C
During Block Erase
and Program.......................... –40 °C to +85 °C
Temperature Under Bias ....... –40 °C to +85 °C
Storage Temperature................. –65 °C to +125 °C
Voltage on Any Pin
(except VCC and VPP)
with Respect to GND ............. –0.5 V to +5.0 V1
NOTICE: This datasheet contains preliminary information on
products in the design phase of development. The
specifications are subject to change without notice. Verify
with your local Intel Sales office that you have the latest
datasheet before finalizing a design.
* WARNING: Stressing the device beyond the "Absolute
Maximum Ratings" may cause permanent damage. These
are stress ratings only. Operation beyond the "Operating
Conditions" is not recommended and extended exposure
beyond the "Operating Conditions" may effect device
reliability.
NOTES:
1.
Minimum DC voltage is –0.5 V on input/output pins.
During transitions, this level may undershoot to –2.0 V
for periods < 20 ns. Maximum DC voltage on
input/output pins is VCC + 0.5 V which, during
transitions, may overshoot to VCC + 2.0 V for periods
< 20 ns.
Maximum DC voltage on VPP may overshoot to +14.0 V
for periods < 20 ns.
Output shorted for no more than one second. No more
than one output shorted at a time.
VPP voltage is normally 1.65 V–3.6 V. Connection to
supply of 11.4 V–12.6 V can only be done for 1000
cycles on the main blocks and 2500 cycles on the
parameter blocks during program/erase. VPP may be
connected to 12 V for a total of 80 hours maximum.
See Section 3.5 for details.
VPP Voltage (for Block
Erase and Program)
with Respect to GND .......–0.5 V to +13.5 V1,2,4
VCC and VCCQ Supply Voltage
with Respect to GND ............. –0.2 V to +5.0 V1
Output Short Circuit Current...................... 100 mA3
2.
3.
4.
4.2
Operating Conditions
Table 10. Temperature and Voltage Operating Conditions
Symbol
Parameter
TA
Operating Temperature
VCC1
VCC Supply Voltage
VCC2
Notes
Min
Max
Units
–40
+85
°C
1
2.7
3.6
Volts
1
3.0
3.6
VCCQ1
I/O Supply Voltage
1
2.7
3.6
Volts
VPP1
Supply Voltage
1
1.65
3.6
Volts
1, 2
11.4
12.6
Volts
2
100,000
VPP2
Cycling
Block Erase Cycling
Cycles
NOTES:
1. VCC and VCCQ must share the same supply when they are in the VCC1 range.
2. Applying VPP = 11.4 V–12.6 V during a program/erase can only be done for a maximum of 1000 cycles on the main blocks
and 2500 cycles on the parameter blocks. VPP may be connected to 12 V for a total of 80 hours maximum. See Section
3.5 for details.
PRODUCT PREVIEW
25
E
3 VOLT ADVANCED+ BOOT BLOCK
4.3
Capacitance
TA = 25 °C, f = 1 MHz
Sym
Parameter
Notes
Typ
Max
Units
Conditions
CIN
Input Capacitance
1
6
8
pF
VIN = 0 V
COUT
Output Capacitance
1
10
12
pF
VOUT = 0 V
NOTE:
1. Sampled, not 100% tested.
4.4
Sym
DC Characteristics
Parameter
VCC
2.7 V–3.6 V
VCCQ
2.7 V–3.6 V
Note
Typ
Max
Unit
Test Conditions
±1
µA
VCC = VCCMax
VCCQ = VCCQMax
VIN = VCCQ or GND
ILI
Input Load Current
1,7
ILO
Output Leakage Current
1,7
0.2
± 10
µA
VCC = VCCMax
VCCQ = VCCQMax
VIN = VCCQ or GND
ICCS
VCC Standby Current
1
10
25
µA
VCC = VCCMax
CE# = RP# = VCC
ICCD
VCC Deep Power-Down
Current
1,7
7
20
µA
VCC = VCCMax
VCCQ = VCCQMax
VIN = VCCQ or GND
RP# = GND ± 0.2 V
ICCR
VCC Read Current
1,5,7
9
18
mA
VCC = VCCMax
VCCQ = VCCQMax
OE# = VIH , CE# = VIL
f = 5 MHz, IOUT = 0 mA
Inputs = VIL or VIH
1,4
18
55
mA
VPP = VPP1
Program in Progress
8
15
mA
VPP = VPP2 (12 V)
Program in Progress
16
45
mA
8
15
mA
VPP = VPP1
Erase in Progress
VPP = VPP2 (12 V)
Erase in Progress
ICCW
ICCE
VCC Program Current
VCC Erase Current
1,4
ICCES
VCC Erase Suspend
Current
1,2,4
10
25
µA
CE# = VIH, Erase Suspend in
Progress
ICCWS
VCC Program Suspend
Current
1,2,4
10
25
µA
CE# = VIH, Program
Suspend in Progress
26
PRODUCT PREVIEW
E
4.4
Sym
3 VOLT ADVANCED+ BOOT BLOCK
DC Characteristics, Continued
Parameter
VCC
2.7 V–3.6 V
VCCQ
2.7 V–3.6 V
Note
Typ
Max
Unit
Test Conditions
IPPD
VPP Deep Power-Down
Current
1
0.2
5
µA
RP# = GND ± 0.2 V
IPPS
VPP Standby Current
1
0.2
5
µA
VPP ≤ VCC
IPPR
VPP Read Current
1
2
±15
µA
VPP ≤ VCC
1,4
50
200
µA
VPP ≥ VCC
IPPW
IPPE
IPPES
IPPWS
VPP Program Current
VPP Erase Current
VPP Erase Suspend Current
VPP Program Suspend Current
PRODUCT PREVIEW
1,4
1,4
1,4
1,4
0.05
0.1
mA
VPP =VPP1
Program in Progress
8
22
mA
VPP = VPP2 (12 V)
Program in Progress
0.05
0.1
mA
VPP = VPP1
Program in Progress
8
22
mA
VPP = VPP2 (12 V)
Program in Progress
0.2
5
µA
VPP = VPP1
Erase Suspend in Progress
50
200
µA
VPP = VPP2 (12 V)
Erase Suspend in Progress
0.2
5
µA
VPP = VPP1
Program Suspend in
Progress
50
200
µA
VPP = VPP2 (12 V)
Program Suspend in
Progress
27
E
3 VOLT ADVANCED+ BOOT BLOCK
4.4
Sym
DC Characteristics, Continued
Parameter
VCC
2.7 V–3.6 V
VCCQ
2.7 V–3.6 V
Note
Min
Max
Unit
0.4
V
VIL
Input Low Voltage
-0.4
VIH
Input High Voltage
VCCQ 0.4 V
VOL
Output Low Voltage
7
-0.10
VOH
Output High Voltage
7
VCCQ 0.1 V
VPPLK
VPP Lock-Out Voltage
3
VPP1
VPP during Program / Erase
3
VPP2
Operations
3,6
VLKO
VCC Prog/Erase Lock Voltage
1.5
V
VLKO2
VCCQ Prog/Erase Lock
Voltage
1.2
V
Test Conditions
V
0.10
V
VCC = VCCMin
VCCQ = VCCQMin
IOL = 100 µA
V
VCC = VCCMin
VCCQ = VCCQMin
IOH = –100 µA
1.0
V
Complete Write Protection
1.65
3.6
V
11.4
12.6
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at nominal VCC, TA = +25 °C.
2. ICCES and ICCWS are specified with device de-selected. If device is read while in erase suspend, current draw is sum of
ICCES and ICCR. If the device is read while in program suspend, current draw is the sum of ICCWS and ICCR.
3. Erase and Program are inhibited when VPP < VPPLK and not guaranteed outside the valid VPP ranges of VPP1 and VPP2.
4. Sampled, not 100% tested.
5. Automatic Power Savings (APS) reduces ICCR to approximately standby levels in static operation (CMOS inputs).
6. Applying VPP = 11.4 V–12.6 V during program/erase can only be done for a maximum of 1000 cycles on the main blocks
and 2500 cycles on the parameter blocks. VPP may be connected to 12 V for a total of 80 hours maximum. See Section
3.4 for details.
7. The test conditions VCCMax, VCCQMax, VCCMin, and VCCQMin refer to the maximum or minimum VCC or VCCQ voltage
listed at the top of each column.
28
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
VCCQ
VCCQ
INPUT
TEST POINTS
2
VCCQ
2
OUTPUT
0.0
0645_07
Figure 7. Input Range and Measurement Points
Test Configuration Component Values Table
Test Configuration
VCCQ
2.7 V–3.6 V Standard
Test
R1
Device
Under Test
Out
CL
CL (pF) R1 (Ω) R2 (Ω)
50
25K
25K
NOTE:
CL includes jig capacitance.
R2
0645_08
Figure 8. Test Configuration
PRODUCT PREVIEW
29
E
3 VOLT ADVANCED+ BOOT BLOCK
4.5
AC Characteristics—Read Operations(1)—Extended Temperature
Product
VCC
Parameter
Note
–90
–110
3.0 V–3.6 V
2.7 V–3.6 V
3.0 V–3.6 V
2.7 V–3.6 V
Min
Min
Min
Min
#
Sym
Max
R1
tAVAV
Read Cycle Time
R2
tAVQV
Address to
Output Delay
R3
tELQV
CE# to Output
Delay
R4
tGLQV
OE# to Output
Delay
R5
tPHQV
RP# to Output
Delay
R6
tELQX
CE# to Output in
Low Z
3
0
0
0
0
ns
R7
tGLQX
OE# to Output in
Low Z
3
0
0
0
0
ns
R8
tEHQZ
CE# to Output in
High Z
3
20
20
20
20
ns
R9
tGHQZ
OE# to Output in
High Z
3
20
20
20
20
ns
R10
tOH
Output Hold from
Address, CE#, or
OE# Change,
Whichever
Occurs First
3
80
Max
90
Max
100
Max
110
Unit
ns
80
90
100
110
ns
2
80
90
100
110
ns
2
30
30
30
30
ns
150
150
150
150
ns
0
0
0
0
ns
NOTES:
1. See AC Waveform: Read Operations.
2. OE# may be delayed up to tELQV–tGLQV after the falling edge of CE# without impact on tELQV.
3. Sampled, but not 100% tested.
4. See Test Configuration (Figure 8).
30
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
CE# (E)
Data
Valid
Device and
Address Selection
VIH
ADDRESSES (A)
VIL
Standby
Address Stable
R1
VIH
VIL
R8
VIH
OE# (G)
VIL
R9
VIH
WE# (W)
VIL
VOH
DATA (D/Q)
VOL
RP#(P)
R7
R10
R3
R6
High Z
R4
Valid Output
High Z
R2
VIH
R5
VIL
Figure 9. AC Waveform: Read Operations
PRODUCT PREVIEW
31
E
3 VOLT ADVANCED+ BOOT BLOCK
AC Characteristics—Write Operations(1)—Extended Temperature
4.6
Product
3.0 V – 3.6 V
-90
80
2.7 V – 3.6 V
#
W1
Symbol
tPHWL /
tPHEL
W2
W3
tELWL /
Parameter
Note
RP# High Recovery to WE#
(CE#) Going Low
-110
100
90
110
Min
Min
Min
Min
Unit
150
150
150
150
ns
0
0
0
0
ns
tWLEL
CE# (WE#) Setup to WE#
(CE#) Going Low
tELEH /
WE# (CE#) Pulse Width
4
50
60
70
70
ns
Data Setup to WE# (CE#)
Going High
2
50
50
60
60
ns
Address Setup to WE# (CE#)
Going High
2
50
60
70
70
ns
0
0
0
0
ns
tWLWH
W4
tDVWH /
tDVEH
W5
tAVWH /
tAVEH
W6
tWHEH /
tEHWH
W7
tWHDX /
Data Hold Time from WE#
(CE#) High
2
0
0
0
0
ns
Address Hold Time from WE#
(CE#) High
2
0
0
0
0
ns
tEHAX
tWHWL /
WE# (CE#) Pulse Width High
4
30
30
30
30
ns
VPP Setup to WE# (CE#) Going
High
3
200
200
200
200
ns
tVPEH
tQVVL
VPP Hold from Valid SRD
3
0
0
0
0
ns
tEHDX
W8
W9
CE# (WE#) Hold Time from
WE# (CE#) High
tWHAX /
tEHEL
W10
W11
tVPWH /
NOTES:
1. Write timing characteristics during erase suspend are the same as during write-only operations.
2. Refer to Table 5 for valid AIN or DIN.
3. Sampled, but not 100% tested.
4. Write pulse width (tWP) is defined from CE# or WE# going low (whichever goes low last) to CE# or WE# going high
(whichever goes high first). Hence, tWP = tWLWH = tELEH = tWLEH = tELWH. Similarly, Write pulse width high (tWPH) is defined
from CE# or WE# going high (whichever goes high first) to CE# or WE# going low (whichever goes low first). Hence,
tWPH = tWHWL = tEHEL = tWHEL = tEHWL.
5. See Test Configuration (Figure 8).
32
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Erase and Program Timings(1)
4.7
VPP
Symbol
tBWPB
tBWMB
tWHQV1 / tEHQV1
tWHQV2 / tEHQV2
tWHQV3 / tEHQV3
1.65 V–3.6 V
11.4 V–12.6 V
Note
Typ(1)
Max
Typ(1)
Max
Unit
8-KB Parameter Block
Program Time (Byte)
2, 3
0.16
0.48
0.08
0.24
s
4-KW Parameter Block
Program Time (Word)
2, 3
0.10
0.30
0.03
0.12
s
64-KB Main Block
Program Time (Byte)
2, 3
1.2
3.7
0.6
1.7
s
32-KW Main Block
Program Time(Word)
2, 3
0.8
2.4
0.24
1
s
Byte Program Time
2, 3
17
165
8
185
µs
Word Program Time
2, 3
22
200
8
185
µs
8-KB Parameter Block
Erase Time (Byte)
2, 3
1
5
0.8
4.8
s
4-KW Parameter Block
Erase Time (Word)
2, 3
0.5
5
0.4
4.8
s
64-KB Main Block
Erase Time (Byte)
2, 3
1
8
1
7
s
32-KW Main Block
Erase Time (Word)
2, 3
1
8
0.6
7
s
Parameter
tWHRH1 / tEHRH1
Program Suspend Latency
3
5
10
5
10
µs
tWHRH2 / tEHRH2
Erase Suspend Latency
3
5
20
5
20
µs
NOTES:
1. Typical values measured at TA = +25 °C and nominal voltages.
2. Excludes external system-level overhead.
3. Sampled, but not 100% tested.
PRODUCT PREVIEW
33
E
3 VOLT ADVANCED+ BOOT BLOCK
VIH
A
B
C
AIN
ADDRESSES [A]
VIL
VIH
D
E
F
AIN
W8
W5
(Note 1)
CE#(WE#) [E(W)]
VIL
W6
VIH W2
OE# [G]
VIL
W9
(Note 1)
VIH
WE#(CE#) [W(E)]
VIL
W3
W4
VIH
DATA [D/Q]
High Z
VIL
RP# [P]
W7
DIN
DIN
W1
Valid
SRD
DIN
VIH
VIL
VIH
WP#
V
[V]
PP
VIL
W10
W11
VPPH 2
VPPH1
VPPLK
VIL
NOTES:
1. CE# must be toggled low when reading Status Register Data. WE# must be inactive (high) when reading Status Register
Data.
A.
B.
C.
D.
E.
F.
VCC Power-Up and Standby.
Write Program or Erase Setup Command.
Write Valid Address and Data (for Program) or Erase Confirm Command.
Automated Program or Erase Delay.
Read Status Register Data (SRD): reflects completed program/erase operation.
Write Read Array Command.
Figure 10. AC Waveform: Program and Erase Operations
34
PRODUCT PREVIEW
E
4.8
3 VOLT ADVANCED+ BOOT BLOCK
Reset Operations
RP# (P)
VIH
VIL
t PLPH
(A) Reset during Read Mode
t PHQV
t PHWL
t PHEL
Abort
Complete
t PLRH
RP# (P)
VIH
t PHQV
t PHWL
t PHEL
VIL
t PLPH
(B) Reset during Program or Block Erase, t PLPH < t PLRH
Abort Deep
Complete PowerDown
RP# (P)
VIH
V IL
t PLRH
t PHQV
t PHWL
t PHEL
t PLPH
(C) Reset Program or Block Erase, t PLPH > t PLRH
Figure 11. AC Waveform: Reset Operation
Table 11. Reset Specifications(1)
VCC 2.7V–3.6V
Symbol
Parameter
Notes
Min
100
Max
Unit
tPLPH
RP# Low to Reset during Read
(If RP# is tied to VCC, this specification is not
applicable)
2,4
ns
tPLRH1
RP# Low to Reset during Block Erase
3,4
22
µs
tPLRH2
RP# Low to Reset during Program
3,4
12
µs
NOTES:
1. See Section 3.1.4 for a full description of these conditions.
2. If tPLPH is < 100 ns the device may still reset but this is not guaranteed.
3. If RP# is asserted while a block erase or word program operation is not executing, the reset will complete within 100 ns.
4. Sampled, but not 100% tested.
PRODUCT PREVIEW
35
E
3 VOLT ADVANCED+ BOOT BLOCK
5.0
ORDERING INFORMATION
T E2 8 F 3 2 0 C3 T 9 0
Package
TE = 48-Lead TSOP
GT = 48-Ball µBGA* CSP
Access Speed (ns)
(90, 110)
Product line designator
for all Intel® Flash products
T = Top Blocking
B = Bottom Blocking
Device Density
320 = x16 (32 Mbit)
032 = x8 (32 Mbit)
160 = x16 (16 Mbit)
800 = x16 (8 Mbit)
016 = x8 (16 Mbit)
008 = x8 (8 Mbit)
Product Family
C3 = Advanced+ Boot Block
VCC = 2.7 V - 3.6 V
VPP = 2.7 V - 3.6 V or 11.4 V - 12.6 V
VALID COMBINATIONS (All Extended Temperature)
40-Lead TSOP
Extended
Extended
Extended
32M
16M
8M
TE28F016C3T90
TE28F016C3B90
48-Ball µBGA* CSP(1)
GT28F032C3T90
GT28F032C3B90
48-Lead TSOP
TE28F320C3T90
TE28F320C3B90
48-Ball µBGA CSP(1)
GT28F320C3T90
GT28F320C3B90
GT28F032C3T110
GT28F032C3B110
GT28F016C3T90
GT28F016C3B90
TE28F320C3T110
TE28F320C3B110
TE28F160C3T90
TE28F160C3B90
GT28F320C3T110
GT28F320C3B110
GT28F160C3T90
GT28F160C3B90
TE28F016C3T110 GT28F016C3T110
TE28F016C3B110 GT28F016C3B110
TE28F160C3T110 GT28F160C3T110
TE28F160C3B110 GT28F160C3B110
TE28F008C3T90
TE28F008C3B90
TE28F800C3T90
TE28F800C3B90
TE28F008C3T110
TE28F008C3B110
TE28F800C3T110
TE28F800C3B110
NOTE:
1.
The 48-Ball µBGA package top side mark reads FXX0C3 where XX is the device density. This mark is identical for both
x8 and x16 products. All product shipping boxes or trays provide the correct information regarding bus architecture,
however once the devices are removed from the shipping media, it may be difficult to differentiate based on the top side
mark. The device identifier (accessible through the Device ID command: see Section 3.2.2 for further details) enables x8
and x16 µBGA package product differentiation.
36
PRODUCT PREVIEW
E
6.0
3 VOLT ADVANCED+ BOOT BLOCK
ADDITIONAL INFORMATION(1,2)
Order Number
Document/Tool
210830
1998 Flash Memory Databook
292216
AP-658 Designing for Upgrade to the Advanced+ Boot Block Flash Memory
292215
AP-657 Designing with the Advanced+ Boot Block Flash Memory
Architecture
3 Volt Advanced+ Boot Block Algorithms (‘C’ and assembly)
http://developer.intel.com/design/flcomp
Contact your Intel
Representative
297874
Flash Data Integrator (FDI) Software Developer’s Kit
FDI Interactive: Play with Intel’s Flash Data Integrator on Your PC
NOTES:
1. Please call the Intel Literature Center at (800) 548-4725 to request Intel documentation. International customers should
contact their local Intel or distribution sales office.
2. Visit Intel’s World Wide Web home page at http://www.Intel.com or http://developer.intel.com for technical documentation
and tools.
PRODUCT PREVIEW
37
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX A
WSM CURRENT/NEXT STATES
Command Input (and Next State)
Current
State
SR.7
Data
When
Read
Read
Array
(FFH)
Program
Setup
(10/40H)
Erase
Setup
(20H)
Erase
Confirm
(D0H)
Read
Status
(70H)
Clear
Status
(50H)
Read Array
“1”
Array
Read Array
Program Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Read Status
“1”
Status
Read Array
Program Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Read
Config.
“1”
Config
Read Array
Program Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Read Query
“1”
CFI
Read Array
Program Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Lock Setup
“1”
Status
Lock Cmd.
Error
“1”
Status
Read Array
Program Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Lock Oper.
(Done)
“1”
Status
Read Array
Program Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Prot. Prog.
Setup
“1”
Status
Protection Register Program
Prot. Prog.
(Not Done)
“0”
Status
Protection Register Program (Not Done)
Prot. Prog.
(Done)
“1”
Status
Read
Status
Read
Array
Lock Command Error
Read Array
Lock
(Done)
Program Setup
Erase
Setup
Prog/Ers
Suspend
(B0H)
Lock
Cmd. Error
Prog/Ers
Resume
(D0)
Lock
(Done)
Lock Cmd. Error
Read Array
Prog. Setup
“1”
Status
Program
(Not Done)
“0”
Status
Prog. Susp.
Status
“1”
Status
Prog. Sus.
Read Array
Program Suspend
Read Array
Program
(Not Done)
Prog. Sus.
Rd. Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Prog. Susp.
Read Array
“1”
Array
Prog. Sus.
Read Array
Program Suspend
Read Array
Program
(Not Done)
Prog. Sus.
Rd. Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Prog. Susp.
Read Config
“1”
Config
Prog. Sus.
Read Array
Program Suspend
Read Array
Program
(Not Done)
Prog. Sus.
Rd. Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Prog. Susp.
Read Query
“1”
CFI
Prog. Sus.
Read Array
Program Suspend
Read Array
Program
(Not Done)
Prog. Sus.
Rd. Array
Program
(Not Done)
Prog. Sus.
Status
Prog. Sus.
Rd. Array
Program
(Done)
“1”
Status
Read Array
Read
Status
Read
Array
Erase Setup
“1”
Status
Erase Cmd.
Error
“1”
Status
Erase
(Not Done)
“0”
Status
Ers. Susp.
Status
“1”
Status
Erase Sus.
Read Array
Program Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus.
Rd. Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Erase Susp.
Array
“1”
Array
Erase Sus.
Read Array
Program Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus.
Rd. Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Ers. Susp.
Read Config
“1”
Config
Erase Sus.
Read Array
Program Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus.
Rd. Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Ers. Susp.
Read Query
“1”
CFI
Erase Sus.
Read Array
Program Setup
Ers. Sus.
Rd. Array
Erase
Ers. Sus.
Rd. Array
Erase
Erase Sus.
Status
Ers. Sus.
Rd. Array
Erase
(Done)
“1”
Status
Read Array
Program Setup
Erase
Setup
Read
Status
Read
Array
38
Program
Program (Not Done)
Program Setup
Erase
Setup
Erase Command Error
Read Array
Program Setup
Prog. Sus.
Status
Program (Not Done)
Read Array
Erase
(Not Done)
Erase
Setup
Erase (Not Done)
Erase
Cmd. Error
Erase
(Not Done)
Erase Command Error
Read Array
Read
Status
Erase Sus.
Status
Erase (Not Done)
Read Array
Read
Array
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX A
WSM CURRENT/NEXT STATES (Continued)
Command Input (and Next State)
Current State
Read Config
(90H)
Read Query
(98H)
Lock Setup
(60H)
Prot. Prog.
Setup (C0H)
Read Array
Read Config.
Read Query
Lock Setup
Prot. Prog.
Setup
Read Array
Read Status
Read Config.
Read Query
Lock Setup
Prot. Prog.
Setup
Read Array
Read Config.
Read Config.
Read Query
Lock Setup
Prot. Prog.
Setup
Read Array
Read Query
Read Config.
Read Query
Lock Setup
Prot. Prog.
Setup
Read Array
Lock
Setup
Lock Confirm
(01H)
Locking Command Error
Lock Down
Confirm
(2FH)
Lock Operation (Done)
Lock Cmd.
Error
Read Config.
Read Query
Lock Setup
Prot. Prog.
Setup
Read Array
Lock Operation
(Done)
Read Config.
Read Query
Lock Setup
Prot. Prog.
Setup
Read Array
Prot. Prog.
Setup
Protection Register Program
Prot. Prog.
(Not Done)
Protection Register Program (Not Done)
Prot. Prog.
(Done)
Read Config.
Read Query
Unlock
Confirm
(D0H)
Lock Setup
Prot. Prog.
Setup
Prog. Setup
Program
Program
(Not Done)
Program (Not Done)
Read Array
Prog. Susp.
Status
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Prog. Susp.
Read Array
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Prog. Susp.
Read Config.
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Prog. Susp.
Read Query.
Prog. Susp.
Read Config.
Prog. Susp.
Read Query
Program Suspend Read Array
Program
(Not Done)
Program
(Done)
Read Config.
Read Query
Erase
Setup
Erase Cmd.
Error
Lock Setup
Prot. Prog.
Setup
Read Array
Erase Command Error
Read Config.
Read Query
Lock Setup
Erase
(Not Done)
Erase
(Not Done)
Prot. Prog.
Setup
Read Array
Erase (Not Done)
Erase Suspend
Status
Erase Suspend
Read Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Erase Suspend
Array
Erase Suspend
Read Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Eras Sus. Read
Config
Erase Suspend
Read Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Eras Sus. Read
Query
Erase Suspend
Read Config.
Erase Suspend
Read Query
Lock Setup
Erase Suspend Read Array
Erase
(Not Done)
Ers.(Done)
Read Config.
Read Query
Lock Setup
PRODUCT PREVIEW
Prot. Prog.
Setup
Read Array
39
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX B
PROGRAM/ERASE FLOWCHARTS
Start
Write 40H
Bus Operation
Command
Write
Program Setup
Write
Program
Program Address/Data
Data = 40H
Data = Data to Program
Addr = Location to Program
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Read
Read Status Register
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Repeat for subsequent programming operations.
No
SR.7 = 1?
Comments
SR Full Status Check can be done after each program or after a sequence of
program operations.
Yes
Write FFH after the last program operation to reset device to read array mode.
Full Status
Check if Desired
Program Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data (See Above)
Bus Operation
1
SR.3 =
0
VPP Range Error
Programming Error
0
1
Comments
Standby
Check SR.3
1 = VPP Low Detect
Standby
Check SR.4
1 = VPP Program Error
Standby
Check SR.1
1 = Attempted Program to
Locked Block - Program
Aborted
1
SR.4 =
SR.1 =
Command
SR.3 MUST be cleared, if set during a program attempt, before further
attempts are allowed by the Write State Machine.
Attempted Program to
Locked Block - Aborted
SR.1, SR.3 and SR.4 are only cleared by the Clear Staus Register Command,
in cases where multiple bytes are programmed before full status is checked.
0
Program Successful
If an error is detected, clear the status register before attempting retry or other
error recovery.
Figure 12. Automated Word Programming Flowchart
40
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Start
Bus
Operation
Command
Write
Program
Suspend
Comments
Data = B0H
Addr = X
Write B0H
Write
Read
Write 70H
Read Status
Standby
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Addr = X
Standby
Standby
Check SR.7
1 = WSM Ready
0 = WSM Busy
Read
Read Status Register
0
SR.7 =
1
0
SR.2 =
Program Completed
Check SR.2
1 = Program Suspended
0 = Program Completed
Standby
Write
Read Array
Write
Read
Read Array
Read
Write
Program
Resume
Read array data from block
other than the one being
programmed.
Write
Program
Resume
Data = D0H
Addr = X
1
Write FFH
Data=70H
Addr=X
Data = FFH
Addr = X
Read Array Data
No
Done
Reading
Yes
Write D0H
Write FFH
Program Resumed
Read Array Data
Figure 13. Program Suspend/Resume Flowchart
PRODUCT PREVIEW
41
E
3 VOLT ADVANCED+ BOOT BLOCK
Start
Bus Operation
Write 20H
Write D0H and
Block Address
Command
Write
Erase Setup
Write
Erase Confirm
Data = D0H
Addr = Within Block to Be
Erased
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Read
Read Status Register
Suspend
Erase Loop
0
SR.7 =
No
Suspend Erase
Comments
Data = 20H
Addr = Within Block to Be
Erased
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Yes
Repeat for subsequent block erasures.
Full Status Check can be done after each block erase or after a sequence of
block erasures.
1
Full Status
Check if Desired
Write FFH after the last write operation to reset device to read array mode.
Block Erase Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data (See Above)
Bus Operation
1
SR.3 =
0
Command
Standby
Check SR.3
1 = VPP Low Detect
Standby
Check SR.4,5
Both 1 = Command Sequence
Error
Standby
Check SR.5
1 = Block Erase Error
Standby
Check SR.1
1 = Attempted Erase of
Locked Block - Erase Aborted
VPP Range Error
1
SR.4,5 =
Command Sequence
Error
0
1
SR.5 =
Block Erase Error
Comments
SR. 1 and 3 MUST be cleared, if set during an erase attempt, before further
attempts are allowed by the Write State Machine.
0
1
SR.1 =
0
Attempted Erase of
Locked Block - Aborted
SR.1, 3, 4, 5 are only cleared by the Clear Staus Register Command, in cases
where multiple bytes are erased before full status is checked.
If an error is detected, clear the status register before attempting retry or other
error recovery.
Block Erase
Successful
Figure 14. Automated Block Erase Flowchart
42
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Bus
Operation
Start
Write
Command
Comments
Program
Data = B0H
Erase Suspend
Suspend
Addr = X
Write B0H
Write
Read
Write 70H
Read Status
Standby
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Addr = X
Standby
Standby
Check SR.7
1 = WSM Ready
0 = WSM Busy
Read
Read Status Register
0
SR.7 =
1
0
SR.6 =
Erase Completed
Data=70H
Addr=X
Standby
Write
Read Array
Write
Read
Read Array
Read
Write
Program
Resume
Write
Erase Resume
1
Write FFH
Check SR.6
1 = Erase Suspended
0 = Erase Completed
Data = FFH
Addr = X
Read array data from block
other than the one being
erased.
Data = D0H
Addr = X
Read Array Data
No
Done
Reading
Yes
Write D0H
Write FFH
Erase Resumed
Read Array Data
Figure 15. Erase Suspend/Resume Flowchart
PRODUCT PREVIEW
43
E
3 VOLT ADVANCED+ BOOT BLOCK
Start
Write 60H
(Configuration Setup)
Write
01H, D0H, or 2FH
Bus
Operation
Command
Write
Program
Config. Setup
Suspend
Data = 60H
Addr = X
Write
Lock, Unlock,
or Lockdown
Data= 01H (Lock Block)
D0H (Unlock Block)
2FH (Lockdown Block)
Addr=Within block to lock
Write
(Optional)
Write 70H
(Read Status Register)
Lock Command
Sequence Error
Read Status Register
1,1
SR.4, SR.5 =
Read
Data = 70H
Status Register Addr = X
Read
(Optional)
Status Register Data
Addr = X
Standby
(Optional)
Check Status Register
80H = no error
30H = Lock Command
Sequence Error
Write
(Optional)
Read
Configuration
Read
(Optional)
Block Lock
Status
Data = 90H
Addr = X
Block Lock Status Data
Addr = Second addr of block
Confirm Locking Change on
DQ1, DQ0. (See Block Locking
State Table for valid
combinations.)
Standby
(Optional)
0,0
Comments
Write 90H
(Read Configuration)
Read Block Lock Status
Locking
Change
Confirmed?
No
Locking Change
Complete
Figure 16. Locking Operations Flowchart
44
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Start
Bus Operation
Command
Write C0H
(Protection Reg.
Program Setup)
Write
Protection Program
Setup
Data = C0H
Write
Protection Program
Data = Data to Program
Addr = Location to Program
Write Protect. Register
Address/Data
Read
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Read Status Register
Protection Program operations can only be addressed within the protection
register address space. Addresses outside the defined space will return an
error.
No
SR.7 = 1?
Comments
Repeat for subsequent programming operations.
Yes
SR Full Status Check can be done after each program or after a sequence of
program operations.
Full Status
Check if Desired
Write FFH after the last program operation to reset device to read array mode.
Program Complete
FULL STATUS CHECK PROCEDURE
Bus Operation
Read Status Register
Data (See Above)
Command
Standby
SR.1 SR.3 SR.4
0
1
1
VPP Low
Standby
0
0
1
Prot. Reg.
Prog. Error
1
0
1
Register
Locked:
Aborted
1, 1
SR.3, SR.4 =
VPP Range Error
0,1
SR.1, SR.4 =
Protection Register
Programming Error
Comments
Standby
SR.3 MUST be cleared, if set during a program attempt, before further
attempts are allowed by the Write State Machine.
1,1
SR.1, SR.4 =
Attempted Program to
Locked Register Aborted
SR.1, SR.3 and SR.4 are only cleared by the Clear Staus Register Command,
in cases of multiple protection register program operations before full status is
checked.
If an error is detected, clear the status register before attempting retry or other
error recovery.
Program Successful
Figure 17. Protection Register Programming Flowchart
PRODUCT PREVIEW
45
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX C
COMMON FLASH INTERFACE QUERY STRUCTURE
This appendix defines the data structure or “database” returned by the Common Flash Interface (CFI) Query
command. System software should parse this structure to gain critical information such as block size, density,
x8/x16, and electrical specifications. Once this information has been obtained, the software will know which
command sets to use to enable flash writes, block erases, and otherwise control the flash component. The
Query is part of an overall specification for multiple command set and control interface descriptions called
Common Flash Interface, or CFI.
C.1
QUERY STRUCTURE OUTPUT
The Query “database” allows system software to gain critical information for controlling the flash component.
This section describes the device’s CFI-compliant interface that allows the host system to access Query data.
Query data are always presented on the lowest-order data outputs (DQ0-7) only. The numerical offset value is
the address relative to the maximum bus width supported by the device. On this family of devices, the Query
table device starting address is a 10h, which is a word address for x16 devices or a byte address for x8
devices.
For a word-wide (x16) device, the first two bytes of the Query structure, “Q”, ”R”, and “Y” in ASCII, appear on
the low byte at word addresses 10h, 11h, and 12h. This CFI-compliant device outputs 00H data on upper
bytes. Thus, the device outputs ASCII “Q” in the low byte (DQ0-7) and 00h in the high byte (DQ8-15).
At Query addresses containing two or more bytes of information, the least significant data byte is presented
at the lower address, and the most significant data byte is presented at the higher address.
In all of the following tables, addresses and data are represented in hexadecimal notation, so the “h” suffix
has been dropped. In addition, since the upper byte of word-wide devices is always “00h,” the leading “00”
has been dropped from the table notation and only the lower byte value is shown. Any x16 device outputs can
be assumed to have 00h on the upper byte in this mode.
Table C1. Summary of Query Structure Output As a Function of Device and Mode
Device
Location
Query Data
(Hex, ASCII)
8-Mbit x8/8-Mbit x 16, 16-Mbit x 8/16-Mbit x 16
10
51 “Q”
(Word or Byte Addresses)
11
52 “R”
12
59 “Y”
46
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Table C2. Example of Query Structure Output of x16 and x8 Devices
Device
Address
Word Addressing:
Query Data
Byte
Address
Byte Addressing:
Query Data
A16–A1
D15–D0
A7–A0
D7–D0
0010h
0011h
0012h
0013h
0014h
0015h
0016h
0017h
0018h
...
C.2
0051h
0052h
0059h
P_IDLO
P_IDHI
PLO
PHI
A_IDLO
A_IDHI
...
“Q”
“R”
“Y”
PrVendor ID# (Lo byte)
PrVendor ID# (HI byte)
PrVendor TblAddr (Lo)
PrVendor TblAddr (Hi)
AltVendor ID# (Lo)
AltVendor ID# (Hi)
10h
11h
12h
13h
14h
15h
16h
17h
18h
...
51h
52h
59h
P_IDLO
P_IDHI
PLO
PHI
A_IDLO
A_IDHI
“Q”
“R”
“Y”
PrVendor ID# (Lo)
PrVendor ID# (Hi)
PrVndr TblAdr (Lo)
PrVndr TblAdr (Hi)
AltVndr ID# (Lo)
AltVndr ID# (Hi)
QUERY STRUCTURE OVERVIEW
The Query command causes the flash component to display the Common Flash Interface (CFI) Query
structure or “database.” The structure sub-sections and address locations are summarized in Table D3.
The following sections describe the Query structure sub-sections in detail.
Table C3. Query Structure(1)
Offset
Sub-Section Name
Description
00h
Manufacturer Code
01h
Device Code
02-0Fh
Reserved
Reserved for vendor-specific information
10h
CFI Query Identification String
Command set ID and vendor data offset
1Bh
System Interface Information
Device timing & voltage information
27h
Device Geometry Definition
Flash device layout
P(3)
Primary Intel-specific Extended Query
table
Vendor-defined additional information
specific to the Primary Vendor Algorithm
NOTES:
1. Refer to Section D.1 and Table D1 for the detailed definition of offset address as a function of device bus width and mode.
2. BA = The beginning location of a Block Address (e.g., 08000h is the beginning location of block 1 when the block size is
32 Kword).
3. Offset 15 defines “P” which points to the Primary Intel-specific Extended Query Table.
PRODUCT PREVIEW
47
E
3 VOLT ADVANCED+ BOOT BLOCK
C.3
BLOCK LOCK STATUS
The Block Lock Status indicates the locking settings of a block.
Table C4. Block Lock Status Register
Offset
(BA+2)h(1)
Length
(bytes)
01h
Description
C3
x16 Device/Mode
Block Lock Status
BA+2:
(see Section 3.3)
NOTE:
1. BA = The beginning location of a Block Address (i.e., 008000h is the beginning location of block 1 in word mode.)
C.4
CFI QUERY IDENTIFICATION STRING
The Identification String provides verification that the component supports the Common Flash Interface
specification. Additionally, it indicates which version of the spec and which vendor-specified command set(s)
is (are) supported.
Table C5. CFI Identification
48
Offset
Length
(Bytes)
Description
8-Mbit, 16-Mbit, 32-Mbit
10h
03h
Query-Unique ASCII string “QRY“
10: 51
11: 52
12: 59
13h
02h
Primary Vendor Command Set and Control Interface
ID Code
16-bit ID Code for Vendor-Specified Algorithms
13: 03
14: 00
15h
02h
Address for Primary Algorithm Extended Query
Table
Offset value = P = 35h
15: 35
16: 00
17h
02h
Alternate Vendor Command Set and Control
Interface ID Code
Second Vendor-Specified Algorithm Supported
Note: 0000h means none exists
17: 00
18: 00
19h
02h
Address for Secondary Algorithm Extended Query
Table
Note: 0000h means none exists
19: 00
1A: 00
PRODUCT PREVIEW
E
C.5
3 VOLT ADVANCED+ BOOT BLOCK
SYSTEM INTERFACE INFORMATION
The following device information can be useful in optimizing system interface software
Table C6. System Interface Information
Offset
Length
(bytes)
Description
8-Mbit, 16-Mbit, 32-Mbit
1Bh
01h
VCC Logic Supply Minimum Program/Erase Voltage
bits 7–4 BCD volts
bits 3–0 BCD 100 mv
1B:27
1Ch
01h
VCC Logic Supply Maximum Program/Erase Voltage
bits 7–4 BCD volts
bits 3–0 BCD 100 mv
1C:36
1Dh
01h
VPP [Programming] Supply Minimum Program/Erase
Voltage
bits 7–4 HEX volts
bits 3–0 BCD 100 mv
1D:B4
1Eh
01h
VPP [Programming] Supply Maximum
Program/Erase Voltage
bits 7–4 HEX volts
bits 3–0 BCD 100 mv
1E:C6
1Fh
01h
Typical Time-Out per Single Byte/Word Program,
2N µ-sec
1F:05
20h
01h
Typical Time-Out for Max. Buffer Write, 2 N µ-sec
20:00
21h
01h
Typical Time-Out per Individual Block Erase,
2N m-sec
21:0A
22h
01h
Typical Time-Out for Full Chip Erase, 2N m-sec
22:00
23h
01h
Maximum Time-Out for Byte/Word Program,
2N Times Typical
23:04
24h
01h
Maximum Time-Out for Buffer Write, 2N Times
Typical
24:00
25h
01h
Maximum Time-Out per Individual Block Erase,
2N Times Typical
25:03
26h
01h
Maximum Time-Out for Chip Erase, 2N Times
Typical
26:00
PRODUCT PREVIEW
49
E
3 VOLT ADVANCED+ BOOT BLOCK
C.6
DEVICE GEOMETRY DEFINITION
This field provides critical details of the flash device geometry.
Table C7. Device Geometry Definition
Offset
Length (bytes)
27h
01h
Device Size = 2N in Number of Bytes
Description
28h
02h
Flash Device Interface Description
value
meaning
28:00, 29:00
28:01,29:00
x8 asynch
x16 asynch
2Ah
02h
Maximum Number of Bytes in Write Buffer = 2N
2Ch
01h
Number of Erase Block Regions within Device:
bits 7–0 = x = # of Erase Block Regions
2Dh
04h
Erase Block Region Information
bits 15–0 = y, Where y+1 = Number of Erase Blocks of Identical
Size within Region
bits 31–16 = z, Where the Erase Block(s) within This Region are
(z) × 256 Bytes
Device Geometry Definition
Offset
8 Mbit
-T
50
16 Mbit
-B
-T
32 Mbit
-B
-T
-B
27h
27:14
27:14
27:15
27:15
27:16
27:16
28h
28:00 (008)
29:00 (008)
28:00 (008)
29:00 (008)
28:00 (016)
29:00 (016)
28:00 (016)
29:00 (016)
28:00 (032)
29:00 (032)
28:00 (032)
29:00 (032)
28:01 (800)
29:00 (800)
28:01 (800)
29:00 (800)
28:01 (160)
29:00 (160)
28:01 (160)
29:00 (160)
28:01 (320)
29:00 (320)
28:01 (320)
29:00 (320)
2Ah
2A:00
2B:00
2A:00
2B:00
2A:00
2B:00
2A:00
2B:00
2A:00
2B:00
2A:00
2B:00
2Ch
2C:02
2C:02
2C:02
2C:02
2C:02
2C:02
2Dh
2D:0E
2E:00
2F:00
30:01
31:07
32:00
33:20
34:00
2D:07
2E:00
2F:20
30:00
31:0E
32:00
33:00
34:01
2D:1E
2E:00
2F:00
30:01
31:07
32:00
33:20
34:00
2D:07
2E:00
2F:20
30:00
31:1E
32:00
33:00
34:01
2D:3E
2E:00
2F:00
30:01
31:07
32:00
33:20
34:00
2D:07
2E:00
2F:20
30:00
31:3E
32:00
33:00
34:01
PRODUCT PREVIEW
E
C.7
3 VOLT ADVANCED+ BOOT BLOCK
INTEL-SPECIFIC EXTENDED QUERY TABLE
Certain flash features and commands are optional. The Intel-Specific Extended Query table specifies this and
other similar types of information.
Table C8. Primary-Vendor Specific Extended Query
Offset(1)
Length
(bytes)
(P)h
03h
Primary Extended Query Table
Unique ASCII String “PRI“
35:
36:
37:
50
52
49
(P+3)h
01h
Major Version Number, ASCII
38:
31
(P+4)h
01h
Minor Version Number, ASCII
39:
30
(P+5)h
04h
Optional Feature & Command Support
3A:
3B:
3C:
3D:
06
00
00
00
3E:
01
Block Lock Status
3F:
03
Defines which bits in the Block Status Register section of
the Query are implemented.
40:
00
Description
bit 0
bit 1
bit 2
bit 3
bit 4
Chip Erase Supported
Suspend Erase Supported
Suspend Program Supported
Lock/Unlock Supported
Queued Erase Supported
8-Mbit, 16-Mbit,
32-Mbit
(1=yes, 0=no)
(1=yes, 0=no)
(1=yes, 0=no)
(1=yes, 0=no)
(1=yes, 0=no)
bits 5–31 reserved for future use; undefined bits
are “0”
(P+9)h
01h
Supported Functions after Suspend
Read Array, Status, and Query are always supported
during suspended Erase or Program operation. This field
defines other operations supported.
bit 0 Program Supported after Erase Suspend
(1=yes, 0=no)
bits 1-7 reserved for future use; undefined bits are “0”
(P+A)h
02h
bit 0 Block Lock Status Register Lock/Unlock bit
(bit 0) active
(1=yes, 0=no)
bit 1 Block Lock Status Register Lock-Down bit
(bit 1) active
(1=yes, 0=no)
Bits 2—15 reserved for future use. Undefined bits
are 0.
PRODUCT PREVIEW
51
3 VOLT ADVANCED+ BOOT BLOCK
Table C8. Primary-Vendor Specific Extended Query (Continued)
Offset(1)
Length
(bytes)
(P+C)h
01h
Description
(P+D)h
01h
Reserved
41:
27
42:
C0
BCD value in volts
BCD value in 100 mv
VPP [Programming] Supply Optimum Program/Erase
voltage
bits 7–4
bits 3–0
(P+E)h
8-Mbit, 16-Mbit,
32-Mbit
VCC Logic Supply Optimum Program/Erase voltage
(highest performance)
bits 7–4
bits 3–0
E
HEX value in volts
BCD value in 100 mv
Reserved for future use
NOTE:
1. The variable P is a pointer which is defined at offset 15h in Table D5.
52
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX D
ARCHITECTURE BLOCK DIAGRAM
DQ0-DQ15
VCCQ
Power
Reduction
Control
Input Buffer
Identifier
Register
Status
Register
Data
Register
Output
Multiplexer
Output Buffer
I/O Logic
CE#
WE#
OE#
RP#
Command
User
Interface
Data
Comparator
WP#
A0-A19
Y-Decoder
Y-Gating/Sensing
Write State
Machine
Address
Counter
32-KWord
Main Block
X-Decoder
4-KWord
Parameter Block
32-KWord
Main Block
Address
Latch
4-KWord
Parameter Block
Input Buffer
Program/Erase
Voltage Switch
VPP
VCC
GND
TEMP
PRODUCT PREVIEW
53
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX E
WORD-WIDE MEMORY MAP DIAGRAMS
E
8-Mbit, 16-Mbit, and 32-Mbit Word-Wide Memory Addressing
Top Boot
Size
(KW)
54
8M
16M
Bottom Boot
32M
Size
(KW)
8M
16M
32M
4
7F000-7FFFF
FF000-FFFFF
1FF000-1FFFFF
32
4
7E000-7EFFF
FE000-FEFFF
1FE000-1FEFFF
32
1F8000-1FFFFF
1F0000-1F7FFF
4
7D000-7DFFF
FD000-FDFFF
1FD000-1FDFFF
32
1E8000-1EFFFF
4
7C000-7CFFF
FC000-FCFFF
1FC000-1FCFFF
32
1E0000-1E7FFF
4
7B000-7BFFF
FB000-FBFFF
1FB000-1FBFFF
32
1D8000-1DFFFF
4
7A000-7AFFF
FA000-FAFFF
1FA000-1FAFFF
32
1D0000-1D7FFF
4
79000-79FFF
F9000-F9FFF
1F9000-1F9FFF
32
1C8000-1CFFFF
4
78000-78FFF
F8000-F8FFF
1F8000-1F8FFF
32
1C0000-1C7FFF
32
70000-77FFF
F0000-F7FFF
1F0000-1F7FFF
32
1B8000-1BFFFF
32
68000-6FFFF
E8000-EFFFF
1E8000-1EFFFF
32
1B0000-1B7FFF
32
60000-67FFF
E0000-E7FFF
1E0000-1E7FFF
32
1A8000-1AFFFF
32
58000-5FFFF
D8000-DFFFF
1D8000-1DFFFF
32
1A0000-1A7FFF
32
50000-57FFF
D0000-D7FFF
1D0000-1D7FFF
32
198000-19FFFF
32
48000-4FFFF
C8000-CFFFF
1C8000-1CFFFF
32
190000-197FFF
32
40000-47FFF
C0000-C7FFF
1C0000-1C7FFF
32
188000-18FFFF
32
38000-3FFFF
B8000-BFFFF
1B8000-1BFFFF
32
180000-187FFF
32
30000-37FFF
B0000-B7FFF
1B0000-1B7FFF
32
178000-17FFFF
32
28000-2FFFF
A8000-AFFFF
1A8000-1AFFFF
32
170000-177FFF
32
20000-27FFF
A0000-A7FFF
1A0000-1A7FFF
32
168000-16FFFF
32
18000-1FFFF
98000-9FFFF
198000-19FFFF
32
160000-167FFF
32
10000-17FFF
90000-97FFF
190000-197FFF
32
158000-15FFFF
32
08000-0FFFF
88000-8FFFF
188000-18FFFF
32
150000-157FFF
32
00000-07FFF
80000-87FFF
180000-187FFF
32
148000-14FFFF
32
78000-7FFFF
178000-17FFFF
32
140000-147FFF
32
70000-77FFF
170000-177FFF
32
138000-13FFFF
32
68000-6FFFF
168000-16FFFF
32
130000-137FFF
32
60000-67FFF
160000-167FFF
32
128000-12FFFF
32
58000-5FFFF
158000-15FFFF
32
120000-127FFF
32
50000-57FFF
150000-157FFF
32
118000-11FFFF
32
48000-4FFFF
148000-14FFFF
32
110000-117FFF
32
40000-47FFF
140000-147FFF
32
108000-10FFFF
32
38000-3FFFF
138000-13FFFF
32
32
30000-37FFF
130000-137FFF
32
32
28000-2FFFF
128000-12FFFF
32
F0000-F7FFF
0F0000-0F7FFF
32
20000-27FFF
120000-127FFF
32
E8000-EFFFF
0E8000-0EFFFF
32
18000-1FFFF
118000-11FFFF
32
E0000-E7FFF
0E0000-0E7FFF
32
10000-17FFF
110000-117FFF
32
D8000-DFFFF
0D8000-0DFFFF
32
08000-0FFFF
108000-10FFFF
32
D0000-D7FFF
0D0000-0D7FFF
32
00000-07FFF
100000-107FFF
32
C8000-CFFFF
0C8000-0CFFFF
100000-107FFF
F8000-FFFFF
0F8000-0FFFFF
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
8-Mbit, 16-Mbit, and 32-Mbit Word-Wide Memory Addressing (Continued)
Top Boot
Size
(KW)
8M
16M
Bottom Boot
32M
Size
(KW)
32
0F8000-0FFFFF
32
0F0000-0F7FFF
32
16M
32M
32
C0000-C7FFF
0C0000-0C7FFF
32
B8000-BFFFF
0B8000-0BFFFF
0E8000-0EFFFF
32
B0000-B7FFF
0B0000-0B7FFF
32
0E0000-0E7FFF
32
A8000-AFFFF
0A8000-0AFFFF
32
0D8000-0DFFFF
32
A0000-A7FFF
0A0000-0A7FFF
32
0D0000-0D7FFF
32
98000-9FFFF
098000-09FFFF
32
0C8000-0CFFFF
32
90000-97FFF
090000-097FFF
32
0C0000-0C7FFF
32
88000-8FFFF
088000-08FFFF
32
0B8000-0BFFFF
32
80000-87FFF
080000-087FFF
32
0B0000-0B7FFF
32
78000-7FFFF
78000-7FFFF
78000-7FFFF
32
0A8000-0AFFFF
32
70000-77FFF
70000-77FFF
70000-77FFF
32
0A0000-0A7FFF
32
68000-6FFFF
68000-6FFFF
68000-6FFFF
32
098000-09FFFF
32
60000-67FFF
60000-67FFF
60000-67FFF
32
090000-097FFF
32
58000-5FFFF
58000-5FFFF
58000-5FFFF
32
088000-08FFFF
32
50000-57FFF
50000-57FFF
50000-57FFF
32
080000-087FFF
32
48000-4FFFF
48000-4FFFF
48000-4FFFF
32
078000-07FFFF
32
40000-47FFF
40000-47FFF
40000-47FFF
32
070000-077FFF
32
38000-3FFFF
38000-3FFFF
38000-3FFFF
32
068000-06FFFF
32
30000-37FFF
30000-37FFF
30000-37FFF
32
060000-067FFF
32
28000-2FFFF
28000-2FFFF
28000-2FFFF
32
058000-05FFFF
32
20000-27FFF
20000-27FFF
20000-27FFF
32
050000-057FFF
32
18000-1FFFF
18000-1FFFF
18000-1FFFF
32
048000-04FFFF
32
10000-17FFF
10000-17FFF
10000-17FFF
32
040000-047FFF
32
08000-0FFFF
08000-0FFFF
08000-0FFFF
32
038000-03FFFF
4
07000-07FFF
07000-07FFF
07000-07FFF
32
030000-037FFF
4
06000-06FFF
06000-06FFF
06000-06FFF
32
028000-02FFFF
4
05000-05FFF
05000-05FFF
05000-05FFF
32
020000-027FFF
4
04000-04FFF
04000-04FFF
04000-04FFF
32
018000-01FFFF
4
03000-03FFF
03000-03FFF
03000-03FFF
32
010000-017FFF
4
02000-02FFF
02000-02FFF
02000-02FFF
32
008000-00FFFF
4
01000-01FFF
01000-01FFF
01000-01FFF
32
000000-007FFF
4
00000-00FFF
00000-00FFF
00000-00FFF
PRODUCT PREVIEW
8M
55
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX F
BYTE-WIDE MEMORY MAP DIAGRAMS
E
Byte-Wide Memory Addressing
Top Boot
Size
(KB)
56
8M
16M
Bottom Boot
32M
Size
(KB)
8M
16M
32M
8
FE000-FFFFF
1FE000-1FFFFF
3FE000-3FFFFF
64
3F0000-3FFFFF
8
FC000-FDFFF
1FC000-1FDFFF
3FC000-3FDFFF
64
3E0000-3EFFFF
8
FA000-FBFFF
1FA000-1FBFFF
3FA000-3FBFFF
64
3D0000-3DFFFF
8
F8000-F9FFF
1F8000-1F9FFF
3F8000-3F9FFF
64
3C0000-3CFFFF
8
F6000-F7FFF
1F6000-1F7FFF
3F6000-3F7FFF
64
3B0000-3BFFFF
8
F4000-F5FFF
1F4000-1F5FFF
3F4000-3F5FFF
64
3A0000-3AFFFF
8
F2000-F3FFF
1F2000-1F3FFF
3F2000-3F3FFF
64
390000-39FFFF
8
F0000-F1FFF
1F0000-1F1FFF
3F0000-3F1FFF
64
380000-38FFFF
64
E0000-EFFFF
1E0000-1EFFFF
3E0000-3EFFFF
64
370000-37FFFF
64
D0000-DFFFF
1D0000-1DFFFF
3D0000-3DFFFF
64
360000-36FFFF
64
C0000-CFFFF
1C0000-1CFFFF
3C0000-3CFFFF
64
350000-35FFFF
64
B0000-BFFFF
1B0000-1BFFFF
3B0000-3BFFFF
64
340000-34FFFF
64
A0000-AFFFF
1A0000-1AFFFF
3A0000-3AFFFF
64
330000-33FFFF
64
90000-9FFFF
190000-19FFFF
390000-39FFFF
64
320000-32FFFF
64
80000-8FFFF
180000-18FFFF
380000-38FFFF
64
310000-31FFFF
64
70000-7FFFF
170000-17FFFF
370000-37FFFF
64
300000-30FFFF
64
60000-6FFFF
160000-16FFFF
360000-36FFFF
64
2F0000-2FFFFF
64
50000-5FFFF
150000-15FFFF
350000-35FFFF
64
2E0000-2EFFFF
64
40000-4FFFF
140000-14FFFF
340000-34FFFF
64
2D0000-2DFFFF
64
30000-3FFFF
130000-13FFFF
330000-33FFFF
64
2C0000-2CFFFF
64
20000-2FFFF
120000-12FFFF
320000-32FFFF
64
2B0000-2BFFFF
64
10000-1FFFF
110000-11FFFF
310000-31FFFF
64
2A0000-2AFFFF
64
00000-0FFFF
100000-10FFFF
300000-30FFFF
64
290000-29FFFF
64
0F0000-0FFFFF
2F0000-2FFFFF
64
280000-28FFFF
64
0E0000-0EFFFF
2E0000-2EFFFF
64
270000-27FFFF
64
0D0000-0DFFFF
2D0000-2DFFFF
64
260000-26FFFF
64
0C0000-0CFFFF
2C0000-2CFFFF
64
250000-25FFFF
64
0B0000-0BFFFF
2B0000-2BFFFF
64
240000-24FFFF
64
0A0000-0AFFFF
2A0000-2AFFFF
64
230000-23FFFF
64
090000-09FFFF
290000-29FFFF
64
220000-22FFFF
64
080000-08FFFF
280000-28FFFF
64
210000-21FFFF
64
070000-07FFFF
270000-27FFFF
64
64
060000-06FFFF
260000-26FFFF
64
64
050000-05FFFF
250000-25FFFF
64
1E0000-1EFFFF
1E0000-1EFFFF
64
040000-04FFFF
240000-24FFFF
64
1D0000-1DFFFF
1D0000-1DFFFF
64
030000-03FFFF
230000-23FFFF
64
1C0000-1CFFFF
1C0000-1CFFFF
64
020000-02FFFF
220000-22FFFF
64
1B0000-1BFFFF
1B0000-1BFFFF
64
010000-01FFFF
210000-21FFFF
64
1A0000-1AFFFF
1A0000-1AFFFF
64
000000-00FFFF
200000-20FFFF
64
190000-19FFFF
190000-19FFFF
200000-20FFFF
1F0000-1FFFFF
1F0000-1FFFFF
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
Byte-Wide Memory Addressing (Continued)
Top Boot
Size
(KB)
8M
16M
Bottom Boot
32M
Size
(KB)
64
1F0000-1FFFFF
64
1E0000-1EFFFF
64
16M
32M
64
180000-18FFFF
180000-18FFFF
64
170000-17FFFF
170000-17FFFF
1D0000-1DFFFF
64
160000-16FFFF
160000-16FFFF
64
1C0000-1CFFFF
64
150000-15FFFF
150000-15FFFF
64
1B0000-1BFFFF
64
140000-14FFFF
140000-14FFFF
64
1A0000-1AFFFF
64
130000-13FFFF
130000-13FFFF
64
190000-19FFFF
64
120000-12FFFF
120000-12FFFF
64
180000-18FFFF
64
110000-11FFFF
110000-11FFFF
64
170000-17FFFF
64
100000-10FFFF
100000-10FFFF
64
160000-16FFFF
64
0F0000-0FFFFF
0F0000-0FFFFF
64
150000-15FFFF
64
E0000-EFFFF
0E0000-0EFFFF
0E0000-0EFFFF
64
140000-14FFFF
64
D0000-DFFFF
0D0000-0DFFFF
0D0000-0DFFFF
64
130000-13FFFF
64
C0000-CFFFF
0C0000-0CFFFF
0C0000-0CFFFF
64
120000-12FFFF
64
B0000-BFFFF
0B0000-0BFFFF
0B0000-0BFFFF
64
110000-11FFFF
64
A0000-AFFFF
0A0000-0AFFFF
0A0000-0AFFFF
64
100000-10FFFF
64
90000-9FFFF
090000-09FFFF
090000-09FFFF
64
0F0000-0FFFFF
64
80000-8FFFF
080000-08FFFF
080000-08FFFF
64
0E0000-0EFFFF
64
70000-7FFFF
070000-07FFFF
070000-07FFFF
64
0D0000-0DFFFF
64
60000-6FFFF
060000-06FFFF
060000-06FFFF
64
0C0000-0CFFFF
64
50000-5FFFF
050000-05FFFF
050000-05FFFF
64
0B0000-0BFFFF
64
40000-4FFFF
040000-04FFFF
040000-04FFFF
64
0A0000-0AFFFF
64
30000-3FFFF
030000-03FFFF
030000-03FFFF
64
090000-09FFFF
64
20000-2FFFF
020000-02FFFF
020000-02FFFF
64
080000-08FFFF
64
10000-1FFFF
010000-01FFFF
010000-01FFFF
64
070000-07FFFF
8
0E000-0FFFF
00E000-00FFFF
00E000-00FFFF
64
060000-06FFFF
8
0C000-0DFFF
00C000-00DFFF
00C000-00DFFF
64
050000-05FFFF
8
0A000-0BFFF
00A000-00BFFF
00A000-00BFFF
64
040000-04FFFF
8
08000-09FFF
008000-009FFF
008000-009FFF
64
030000-03FFFF
8
06000-07FFF
006000-007FFF
006000-007FFF
64
020000-02FFFF
8
04000-05FFF
004000-005FFF
004000-005FFF
64
010000-01FFFF
8
02000-03FFF
002000-003FFF
002000-003FFF
64
000000-00FFFF
8
00000-01FFF
000000-001FFF
000000-001FFF
PRODUCT PREVIEW
8M
F0000-FFFFF
57
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX G
DEVICE ID TABLE
Read Configuration Addresses and Data
Item
Address
Data
x16
00000
0089
x8
00000
89
8-Mbit x 16-T
x16
00001
88C0
8-Mbit x 16-B
x16
00001
88C1
16-Mbit x 16-T
x16
00001
88C2
16-Mbit x 16-B
x16
00001
88C3
32-Mbit x 16-T
x16
00001
88C4
32-Mbit x 16-B
x16
00001
88C5
8-Mbit x 8-T
x8
00001
C0
8-Mbit x 8-B
x8
00001
C1
16-Mbit x 8-T
x8
00001
C2
16-Mbit x 8-B
x8
00001
C3
32-Mbit x 8-T
x8
00001
C4
32-Mbit x 8-B
x8
00001
C5
Manufacturer Code
Device Code
NOTE: Other locations within the configuration address space are reserved by Intel for future use.
58
PRODUCT PREVIEW
E
3 VOLT ADVANCED+ BOOT BLOCK
APPENDIX H
PROTECTION REGISTER ADDRESSING
Word-Wide Protection Register Addressing
Word
Use
A7
A6
A5
A4
A3
A2
A1
A0
LOCK
Both
1
0
0
0
0
0
0
0
0
Factory
1
0
0
0
0
0
0
1
1
Factory
1
0
0
0
0
0
1
0
2
Factory
1
0
0
0
0
0
1
1
3
Factory
1
0
0
0
0
1
0
0
4
User
1
0
0
0
0
1
0
1
5
User
1
0
0
0
0
1
1
0
6
User
1
0
0
0
0
1
1
1
7
User
1
0
0
0
1
0
0
0
Byte-Wide Protection Register Addressing
Byte
Use
A11
A7
A6
A5
A4
A3
A2
A1
A0
LOCK
Both
0
1
0
0
0
0
0
0
0
0
Factory
0
1
0
0
0
0
0
0
1
1
Factory
1
1
0
0
0
0
0
0
1
2
Factory
0
1
0
0
0
0
0
1
0
3
Factory
1
1
0
0
0
0
0
1
0
4
Factory
0
1
0
0
0
0
0
1
1
5
Factory
1
1
0
0
0
0
0
1
1
6
Factory
0
1
0
0
0
0
1
0
0
7
Factory
1
1
0
0
0
0
1
0
0
8
User
0
1
0
0
0
0
1
0
1
9
User
1
1
0
0
0
0
1
0
1
10
User
0
1
0
0
0
0
1
1
0
11
User
1
1
0
0
0
0
1
1
0
12
User
0
1
0
0
0
0
1
1
1
13
User
1
1
0
0
0
0
1
1
1
14
User
0
1
0
0
0
1
0
0
0
15
User
1
1
0
0
0
0
0
0
0
PRODUCT PREVIEW
59
Similar pages