TI GTL16923 18-bit lvttl-to-gtl/gtl bus transceiver Datasheet

www.ti.com
FEATURES
•
•
•
•
•
•
•
•
•
•
Member of the Texas Instruments Widebus™
Family
OEC™ Circuitry Improves Signal Integrity and
Reduces Electromagnetic Interference
D-Type Flip-Flops With Qualified Storage
Enable
Translates Between GTL/GTL+ Signal Levels
and LVTTL Logic Levels
Supports Mixed-Mode Signal Operation on All
Ports (5-V Input/Output Voltages With
3.3-V VCC)
Ioff Supports Partial-Power-Down Mode
Operation
Bus Hold on Data Inputs Eliminates the Need
for External Pullup/Pulldown Resistors on
A Port
Distributed VCC and GND Pins Minimize
High-Speed Switching Noise
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
DESCRIPTION/ORDERING INFORMATION
The SN74GTL16923 is an 18-bit registered bus
transceiver that provides LVTTL-to-GTL/GTL+ and
GTL/GTL+-to-LVTTL signal-level translation. This
device is partitioned as two 9-bit transceivers with
individual output-enable controls and contains D-type
flip-flops for temporary storage of data flowing in
either direction. This device provides an interface
between cards operating at LVTTL logic levels and a
backplane operating at GTL/GTL+ signal levels.
Higher-speed operation is a direct result of the
reduced output swing (<1 V), reduced input threshold
levels, and OEC™ circuitry.
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
DGG PACKAGE
(TOP VIEW)
CEAB
1A1
GND
1A2
1A3
GND
VCC
1A4
GND
1A5
1A6
GND
1A7
1A8
GND
1A9
2A1
GND
2A2
2A3
GND
2A4
2A5
GND
2A6
VCC
GND
2A7
2A8
GND
2A9
CEBA
1
64
2
63
3
62
4
61
5
60
6
59
7
58
8
57
9
56
10
55
11
54
12
53
13
52
14
51
15
50
16
49
17
48
18
47
19
46
20
45
21
44
22
43
23
42
24
41
25
40
26
39
27
38
28
37
29
36
30
35
31
34
32
33
CLKAB
1OEAB
1OEBA
1B1
GND
1B2
1B3
VCC
1B4
1B5
1B6
GND
1B7
1B8
GND
1B9
2B1
GND
2B2
2B3
GND
2B4
2B5
2B6
VREF
2B7
2B8
GND
2B9
2OEBA
2OEAB
CLKBA
<br/>
The user has the flexibility of using this device at either GTL (VTT = 1.2 V and VREF = 0.8 V) or the preferred
higher noise margin GTL+ (VTT = 1.5 V and VREF = 1 V) signal levels. GTL+ is the Texas Instruments derivative
of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3. The B port normally operates at GTL or
GTL+ signal levels, while the A-port and control inputs are compatible with LVTTL logic levels. All inputs can be
driven from either 3.3-V or 5-V devices, which allows use in a mixed 3.3-V/5-V system environment. VREF is the
reference input voltage for the B port.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus, OEC are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1996–2005, Texas Instruments Incorporated
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
Data flow in each direction is controlled by the output-enable (OEAB and OEBA) and clock (CLKAB and CLKBA)
inputs. The clock-enable (CEAB and CEBA) inputs enable or disable the clock for all 18 bits at a time. However,
OEAB and OEBA are designed to control each 9-bit transceiver independently, which makes the device more
versatile.
For A-to-B data flow, the device operates on the low-to-high transition of CLKAB if CEAB is low. When OEAB is
low, the outputs are active. When OEAB is high, the outputs are in the high-impedance state. Data flow for B to
A is similar to that of A to B, but uses OEBA, CLKBA, and CEBA.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
Active bus-hold circuitry holds unused or undriven LVTTL inputs at a valid logic state. Use of pullup or pulldown
resistors with the bus-hold circuitry is not recommended.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
TSSOP – DGG
ORDERABLE PART NUMBER
Tape and reel
TOP-SIDE MARKING
SN74GTL16923DGGR
GTL16923
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
FUNCTION TABLE (1)
INPUTS
(1)
(2)
2
CEAB
OEAB
CLKAB
A
OUTPUT
B
MODE
Isolation
X
H
X
X
Z
H
L
X
X
B0 (2)
X
L
H or L
X
B0 (2)
L
L
↑
L
L
L
L
↑
H
H
Latched storage of A data
Clocked storage of A data
A-to-B data flow is shown. B-to-A data flow is similar, but uses OEBA, CLKBA, and CEBA.
Output level before the indicated steady-state input conditions were established
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
LOGIC DIAGRAM (POSITIVE LOGIC)
40
VREF
63
1OEAB
1
CEAB
64
CLKAB
33
CLKBA
32
CEBA
62
1OEBA
CE
2
1A1
61
1B1
1D
CLK
CE
1D
CLK
To Eight Other Channels
34
2OEAB
35
2OEBA
2A1
CE
17
1D
48
2B1
CLK
CE
1D
CLK
To Eight Other Channels
3
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
–0.5
4.6
V
VI
Input voltage range (2)
–0.5
7
V
7
V
VO
Voltage range applied to any output in the high or power-off
IO
Current into any output in the low state
IO
Current into any A-port output in the high state (3)
state (2)
–0.5
A port
48
B port
100
Continuous current through each VCC or GND
UNIT
mA
48
mA
±100
mA
mA
IIK
Input clamp current
VI < 0
–50
IOK
Output clamp current
VO < 0
–50
mA
θJA
Package thermal impedance (4)
55
°C/W
Tstg
Storage temperature range
150
°C
(1)
(2)
(3)
(4)
–65
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
This current flows only when the output is in the high state and VO > VCC.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions (1) (2) (3) (4)
VCC
Supply voltage
VTT
Termination voltage
VREF
Reference voltage
VI
Input voltage
VIH
High-level input voltage
VIL
Low-level input voltage
IIK
Input clamp current
IOH
High-level output current
IOL
Low-level output current
TA
Operating free-air temperature
(1)
(2)
(3)
(4)
4
MIN
NOM
MAX
UNIT
3.15
3.3
3.45
V
GTL
1.14
1.2
1.26
GTL+
1.35
1.5
1.65
GTL
0.74
0.8
0.87
GTL+
0.87
1
1.1
B port
0
VTT
Except B port
0
5.5
B port
Except B port
VREF + 50 mV
VREF – 50 mV
Except B port
V
V
V
2
B port
V
0.8
V
–18
mA
A port
–24
mA
A port
24
B port
50
–40
85
mA
°C
All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Normal connection sequence is GND first, VCC = 3.3 V, I/O, control inputs, VTT, VREF (any order) last.
VTT and RTT can be adjusted to accommodate backplane impedances if the dc recommended IOL ratings are not exceeded.
VREF can be adjusted to optimize noise margins, but normally is two-thirds VTT.
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
Electrical Characteristics
over recommended operating free-air temperature range for GTL/GTL+ (unless otherwise noted)
PARAMETER
VIK
TEST CONDITIONS
MIN TYP (1) MAX
VCC = 3.15 V, II = –18 mA
VCC = 3.15 V to 3.45 V,
VOH
A port
VCC = 3.15 V
VCC = 3.15 V to 3.45 V,
A port
VOL
VCC = 3.15 V
VCC = 3.15 V to 3.45 V,
B port
II
VCC = 3.15 V
B port
VCC = 3.45 V,
A-port and control inputs
VCC = 3.45 V
Ioff
IOH = –100 µA
VCC – 0.2
IOH = –12 mA
2.4
IOH = –24 mA
2
A port
VCC = 3.15 V
IOL = 100 µA
0.2
IOL = 12 mA
0.4
IOL = 24 mA
0.5
IOL = 100 µA
0.2
IOL = 10 mA
0.2
IOL = 40 mA
0.4
IOL = 50 mA
0.55
VI = 5.5 V or GND
±5
VI = 5.5 V or GND
µA
±20
±100
VI = 2 V
V
±5
VI = VCC or GND
VI = 0.8 V
V
V
VCC = 0, VI or VO = 0 to 5.5 V
II(hold)
UNIT
–1.2
µA
75
µA
–75
VCC = 3.45 V (2),
VI = 0.8 V to 2 V
±500
IOZ (3)
A port
VCC = 3.45 V,
VO = VCC or GND
±10
µA
IOZH
B port
VCC = 3.45 V,
VO = 1.5 V
10
µA
Outputs high
60
Outputs low
60
Outputs disabled
60
ICC
A or B port
VCC = 3.45 V, A-port or control inputs at VCC or GND,
One input at VCC – 0.6 V
∆ICC (4)
Ci
Cio
(1)
(2)
(3)
(4)
VCC = 3.45 V,
IO = 0,
VI = VCC or GND
mA
500
µA
pF
Control inputs
VI = 3.15 V or 0
2.5
3
A port
VO = 3.15 V or 0
6
8.5
B port
VO = 3.15 V or 0
7
9.5
pF
All typical values are at VCC = 3.3 V, TA = 25°C.
This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to
another.
For I/O ports, the parameter IOZ includes the input leakage current.
This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
5
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
Timing Requirements
over recommended ranges of supply voltage and operating free-air temperature for GTL (unless otherwise noted)
MIN
fclock
Clock frequency
tw
Pulse duration, CLK high or low
tsu
Setup time
th
Hold time
MAX
UNIT
200
MHz
2.5
Data before CLK↑
2.6
CE before CLK↑
3.3
Data after CLK↑
0.1
CE after CLK↑
ns
ns
ns
0
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature for GTL (see Figure 1)
PARAMETER
MIN TYP (1)
MAX
fmax
200
2.2
5.8
2.1
6.3
1.7
5.3
2
5
tdis
ten
CLKAB
B
OEAB
B
UNIT
MHz
ns
Both transitions
tr
Transition time, B outputs (0.6 V to 1 V)
0.3
2.9
ns
tf
Transition time, B outputs (1 V to 0.6 V)
0.1
3.9
ns
1.8
5
1.7
4.8
1.3
4.8
2
4.8
tPHL
ten
tdis
0.5
ns
Slew rate
tPLH
6
TO
(OUTPUT)
tPLH
tPHL
(1)
FROM
(INPUT)
CLKBA
A
OEBA
A
All typical values are at VCC = 3.3 V, TA = 25°C.
V/ns
ns
ns
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
Timing Requirements
over recommended ranges of supply voltage and operating free-air temperature for GTL+ (unless otherwise noted)
MIN
fclock
Clock frequency
tw
Pulse duration, CLK high or low
tsu
Setup time
th
Hold time
MAX
UNIT
200
MHz
2.5
Data before CLK↑
2.3
CE before CLK↑
3.3
Data after CLK↑
0.1
CE after CLK↑
ns
ns
ns
0
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature for GTL+ (see Figure 1)
PARAMETER
TO
(OUTPUT)
MIN TYP (1)
MAX
fmax
200
tPLH
2.2
4
5.9
2.1
4
6.1
1.9
3.4
5.2
1.7
3.1
5.1
tPHL
tPLH
tPHL
CLKAB
B
OEAB
B
UNIT
MHz
ns
Both transitions
tr
Transition time, B outputs (0.6 V to 1.3 V)
0.6
1.3
2.6
ns
tf
Transition time, B outputs (1.3 V to 0.6 V)
0.4
1.3
3
ns
1.8
3.5
5.1
1.7
3.3
4.9
1.3
2.9
4.8
2
3.2
5
tPHL
ten
tdis
0.5
ns
Slew rate
tPLH
(1)
FROM
(INPUT)
CLKBA
A
OEBA
A
V/ns
ns
ns
All typical values are at VCC = 3.3 V, TA = 25°C.
7
SN74GTL16923
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS674G – AUGUST 1996 – REVISED APRIL 2005
PARAMETER MEASUREMENT INFORMATION
VTT = 1.5 V, VREF = 1 V
VTT
6V
500 Ω
From Output
Under Test
S1
Open
TEST
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
GND
CL = 50 pF
(see Note A)
500 Ω
25 Ω
From Output
Under Test
CL = 30 pF
(see Note A)
S1
Open
6V
GND
LOAD CIRCUIT FOR A OUTPUTS
Test
Point
LOAD CIRCUIT FOR B OUTPUTS
3V
Timing
Input
tw
1.5 V
0V
3V
1.5 V
Input
1.5 V
tsu
0V
VOLTAGE WAVEFORMS
PULSE DURATION
3V
Input
1.5 V
1.5 V
th
3V
Data Input
A port
1.5 V
Data Input
B port
VREF
1.5 V
0V
VTT
VREF
0V
0V
tPLH
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
tPHL
VOH
Output
VREF
VREF
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
(CLKAB to B port)
1.5 V
tPZL
1.5 V
0V
tPLH
Output
Waveform 1
S1 at 6 V
(see Note B)
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
(CLKBA to A port)
1.5 V
tPLZ
3V
1.5 V
tPZH
tPHL
VOH
Output
1.5 V
0V
3V
Input
3V
Output
Control
Output
Waveform 2
S1 at GND
(see Note B)
VOL + 0.3 V
VOL
tPHZ
VOH
1.5 V
VOH − 0.3 V
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
(A port)
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
Figure 1. Load Circuits and Voltage Waveforms
8
PACKAGE OPTION ADDENDUM
www.ti.com
5-Sep-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
74GTL16923DGGRE4
ACTIVE
TSSOP
DGG
64
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74GTL16923DGGR
ACTIVE
TSSOP
DGG
64
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Apr-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
SN74GTL16923DGGR
26-Apr-2007
Package Pins
DGG
64
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
MLA
330
24
8.4
17.3
1.7
12
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
SN74GTL16923DGGR
DGG
64
MLA
333.2
333.2
31.75
Pack Materials-Page 2
W
Pin1
(mm) Quadrant
24
Q1
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
0,50
48
0,08 M
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
1
0,25
24
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
48
56
64
A MAX
12,60
14,10
17,10
A MIN
12,40
13,90
16,90
DIM
4040078 / F 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power
Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
Similar pages