Renesas H8/3068F-ZTAT Renesas 16-bit single-chip microcomputer h8 family/h8/300h sery Datasheet

REJ09B0258-0300
The revision list can be viewed directly by
clicking the title page.
The revision list summarizes the locations of
revisions and additions. Details should always
be checked by referring to the relevant text.
16
H8/3068F-ZTAT
Hardware Manual
Renesas 16-Bit Single-Chip Microcomputer
H8 Family/H8/300H Series
H8/3068F
Rev. 3.00
Revision Date: Sep 14, 2005
HD64F3068F,
HD64F3068TE
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and
more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corp. product best suited to the customer's application; they do not convey any license
under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or
a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any thirdparty's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corp. without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or
an authorized Renesas Technology Corp. product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising
from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means,
including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data,
diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total
system before making a final decision on the applicability of the information and products. Renesas
Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or
system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when
considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must
be exported under a license from the Japanese government and cannot be imported into a country
other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products
contained therein.
Rev. 3.00 Sep 14, 2005 page ii of xxii
Preface
The H8/3068F is a group of high-performance single-chip microcontrollers that integrate system
supporting functions together with an H8/300H CPU core.
The H8/300H CPU has a 32-bit internal architecture with sixteen 16-bit general registers, and a
concise, optimized instruction set designed for speed. It can address a 16-Mbyte linear address
space.
The on-chip supporting functions include ROM, RAM, 16-bit timers, 8-bit timers, a
programmable timing pattern controller (TPC), a watchdog timer (WDT), a serial communication
interface (SCI), an A/D converter, a D/A converter, I/O ports, a DMA controller (DMAC), and
other facilities. The three-channel SCI has been expanded to support the ISO/IEC7816-3 smart
card interface. Functions have also been added to reduce power consumption in battery-powered
applications: individual modules can be placed in standby, and the frequency of the system clock
supplied to the chip can be divided down under software control.
The address space is divided into eight areas. The data bus width and access cycle length can be
selected independently in each area, simplifying the connection of different types of memory.
Seven MCU operating modes (modes 1 to 7) are provided, offering a choice of data bus width and
address space size.
With these features, the H8/3068F offers easy implementation of compact, high-performance
systems.
The H8/3068F has an F-ZTAT™* version with on-chip flash memory that can be programmed
on-board. This version enables users to respond quickly and flexibly to changing application
specifications.
This manual describes the H8/3068F hardware. For details of the instruction set, refer to the
H8/300H Series Programming Manual.
Note: * F-ZTAT™ (Flexible ZTAT) is a registered trademark of Renesas Technology Corp.
Rev. 3.00 Sep 14, 2005 page iii of xxii
Rev. 3.00 Sep 14, 2005 page iv of xxii
Main Revisions for this Edition
Item
Page
Revision (See Manual for Details)
All

All references to Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and
other Hitachi brand names changed to Renesas Technology Corp.
Designation for categories changed from “series” to “group”
19.2.1 Connecting 651
a Crystal Resonator
Table 19.1 (1)
Damping Resistance
Value
Note amended
Note: A crystal resonator between 2 MHz and 25 MHz can be
used. If the chip is to be operated at less than 2 MHz, the
on-chip frequency divider should be used. (A crystal
resonator of less than 2 MHz cannot be used.)
“Preliminary” deleted
Section 21
Electrical
Characteristics
675 to
706
21.1.2 DC
Characteristics
677, 678 Table and note amended
Table 21.2 DC
Characteristics (1)
Item
Symbol
Min
Typ
Max
Normal
Current
2
dissipation* operation
ICC*4
—
32
47
(5.0 V)
Unit
Test
Conditions
mA
f = 20 MHz
37
58
(5.0 V)
Sleep mode
—
24
38
(5.0 V)
f = 25 MHz
mA
29
47
(5.0 V)
Module
standby mode
—
19
31
(5.0 V)
f = 20 MHz
f = 25 MHz
mA
21
37
(5.0 V)
f = 20 MHz
f = 25 MHz
Standby
3
mode*
—
1.0
10
µA
Ta
—
—
80
µA
50˚C
50˚C
Flash memory
programming/
5
erasing*
—
37
57
mA
f = 20 MHz
42
68
Ta
f = 25 MHz
Notes: 3. The values are for VRAM ≤ VCC < 4.5 V, VIH min = VCC ×
0.9, and VIL max = 0.3 V.
4. ICC max. (normal operation)
= 3.0 (mA) + 0.40 (mA/(MHz × V)) × VCC × f
ICC max. (sleep mode)
= 3.0 (mA) + 0.32 (mA/(MHz × V)) × VCC × f
ICC max. (sleep mode + module standby mode)
= 3.0 (mA) + 0.25 (mA/(MHz × V)) × VCC × f
The Typ values for power consumption are reference
values.
5. Sum of current dissipation in normal operation and
current dissipation in program/erase operations.
Rev. 3.00 Sep 14, 2005 page v of xxii
Item
Page
21.1.6 Flash
Memory
Characteristics
690, 691 Table amended and notes added
Table 21.10 Flash
Memory
Characteristics
Revision (See Manual for Details)
Item
Symbol Min
Typ
Max
Unit
1 2 4
Programming time* * *
tP
—
10
200
ms/
128 bytes
Erase time* * *
1
tE
—
100
1200
Reprogramming count
NWEC
100*6
10,000*7 —
Times
Data retention period
tDRP
10*8
—
Years
3
5
—
Notes
ms/block
Notes: 6. Minimum number of times at which all characteristics are
guaranteed after reprogramming. (Reprogramming count
from 1 to minimum value is guaranteed.)
7. Reference characteristics at 25°C. (This is an indication
that reprogramming operations can normally be
performed up to this figure.)
8. Data retention characteristics when reprogramming is
performed correctly within the specification values,
including the minimum data retention period.
Rev. 3.00 Sep 14, 2005 page vi of xxii
Contents
Section 1 Overview .............................................................................................................
1.1
1.2
1.3
1
Overview........................................................................................................................... 1
Block Diagram.................................................................................................................. 6
Pin Description ................................................................................................................. 7
1.3.1 Pin Arrangement.................................................................................................. 7
1.3.2 Pin Functions ....................................................................................................... 8
1.3.3 Pin Assignments in Each Mode ........................................................................... 13
Section 2 CPU ...................................................................................................................... 19
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Overview...........................................................................................................................
2.1.1 Features................................................................................................................
2.1.2 Differences from H8/300 CPU ............................................................................
CPU Operating Modes......................................................................................................
Address Space...................................................................................................................
Register Configuration......................................................................................................
2.4.1 Overview..............................................................................................................
2.4.2 General Registers.................................................................................................
2.4.3 Control Registers .................................................................................................
2.4.4 Initial CPU Register Values.................................................................................
Data Formats.....................................................................................................................
2.5.1 General Register Data Formats............................................................................
2.5.2 Memory Data Formats .........................................................................................
Instruction Set...................................................................................................................
2.6.1 Instruction Set Overview .....................................................................................
2.6.2 Instructions and Addressing Modes.....................................................................
2.6.3 Tables of Instructions Classified by Function......................................................
2.6.4 Basic Instruction Formats ....................................................................................
2.6.5 Notes on Use of Bit Manipulation Instructions ...................................................
Addressing Modes and Effective Address Calculation.....................................................
2.7.1 Addressing Modes ...............................................................................................
2.7.2 Effective Address Calculation .............................................................................
Processing States...............................................................................................................
2.8.1 Overview..............................................................................................................
2.8.2 Program Execution State .....................................................................................
2.8.3 Exception-Handling State ....................................................................................
2.8.4 Exception-Handling Sequences ...........................................................................
2.8.5 Bus-Released State ..............................................................................................
19
19
20
21
22
23
23
24
25
26
27
27
29
30
30
31
32
41
42
44
44
46
50
50
51
51
53
54
Rev. 3.00 Sep 14, 2005 page vii of xxii
2.9
2.8.6 Reset State ...........................................................................................................
2.8.7 Power-Down State ...............................................................................................
Basic Operational Timing .................................................................................................
2.9.1 Overview..............................................................................................................
2.9.2 On-Chip Memory Access Timing........................................................................
2.9.3 On-Chip Supporting Module Access Timing ......................................................
2.9.4 Access to External Address Space.......................................................................
54
55
56
56
56
57
58
Section 3 MCU Operating Modes .................................................................................. 59
3.1
3.2
3.3
3.4
3.5
3.6
Overview...........................................................................................................................
3.1.1 Operating Mode Selection ...................................................................................
3.1.2 Register Configuration.........................................................................................
Mode Control Register (MDCR) ......................................................................................
System Control Register (SYSCR) ...................................................................................
Operating Mode Descriptions ...........................................................................................
3.4.1 Mode 1.................................................................................................................
3.4.2 Mode 2.................................................................................................................
3.4.3 Mode 3.................................................................................................................
3.4.4 Mode 4.................................................................................................................
3.4.5 Mode 5.................................................................................................................
3.4.6 Mode 6.................................................................................................................
3.4.7 Mode 7.................................................................................................................
Pin Functions in Each Operating Mode ............................................................................
Memory Map in Each Operating Mode ............................................................................
3.6.1 Note on Reserved Areas ......................................................................................
59
59
60
61
62
64
64
64
64
65
65
65
65
66
67
67
Section 4 Exception Handling ......................................................................................... 73
4.1
4.2
4.3
4.4
4.5
4.6
Overview...........................................................................................................................
4.1.1 Exception Handling Types and Priority...............................................................
4.1.2 Exception Handling Operation ............................................................................
4.1.3 Exception Vector Table .......................................................................................
Reset .................................................................................................................................
4.2.1 Overview..............................................................................................................
4.2.2 Reset Sequence ....................................................................................................
4.2.3 Interrupts after Reset............................................................................................
Interrupts...........................................................................................................................
Trap Instruction ................................................................................................................
Stack Status after Exception Handling..............................................................................
Notes on Stack Usage .......................................................................................................
Rev. 3.00 Sep 14, 2005 page viii of xxii
73
73
73
74
76
76
76
79
80
81
82
83
Section 5 Interrupt Controller .......................................................................................... 85
5.1
5.2
5.3
5.4
5.5
Overview...........................................................................................................................
5.1.1 Features................................................................................................................
5.1.2 Block Diagram.....................................................................................................
5.1.3 Pin Configuration.................................................................................................
5.1.4 Register Configuration.........................................................................................
Register Descriptions........................................................................................................
5.2.1 System Control Register (SYSCR) ......................................................................
5.2.2 Interrupt Priority Registers A and B (IPRA, IPRB).............................................
5.2.3 IRQ Status Register (ISR)....................................................................................
5.2.4 IRQ Enable Register (IER) ..................................................................................
5.2.5 IRQ Sense Control Register (ISCR) ....................................................................
Interrupt Sources...............................................................................................................
5.3.1 External Interrupts ...............................................................................................
5.3.2 Internal Interrupts ................................................................................................
5.3.3 Interrupt Vector Table .........................................................................................
Interrupt Operation ...........................................................................................................
5.4.1 Interrupt Handling Process ..................................................................................
5.4.2 Interrupt Sequence ...............................................................................................
5.4.3 Interrupt Response Time......................................................................................
Usage Notes ......................................................................................................................
5.5.1 Contention between Interrupt and Interrupt-Disabling Instruction......................
5.5.2 Instructions that Inhibit Interrupts .......................................................................
5.5.3 Interrupts during EEPMOV Instruction Execution..............................................
85
85
86
87
87
88
88
89
96
97
98
99
99
100
100
104
104
109
110
111
111
112
112
Section 6 Bus Controller ................................................................................................... 113
6.1
6.2
Overview...........................................................................................................................
6.1.1 Features................................................................................................................
6.1.2 Block Diagram.....................................................................................................
6.1.3 Pin Configuration.................................................................................................
6.1.4 Register Configuration.........................................................................................
Register Descriptions........................................................................................................
6.2.1 Bus Width Control Register (ABWCR)...............................................................
6.2.2 Access State Control Register (ASTCR) .............................................................
6.2.3 Wait Control Registers H and L (WCRH, WCRL)..............................................
6.2.4 Bus Release Control Register (BRCR) ................................................................
6.2.5 Bus Control Register (BCR) ................................................................................
6.2.6 Chip Select Control Register (CSCR)..................................................................
6.2.7 DRAM Control Register A (DRCRA).................................................................
6.2.8 DRAM Control Register B (DRCRB) .................................................................
113
113
115
116
117
118
118
119
120
124
126
129
130
132
Rev. 3.00 Sep 14, 2005 page ix of xxii
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.2.9 Refresh Timer Control/Status Register (RTMCSR) ............................................
6.2.10 Refresh Timer Counter (RTCNT)........................................................................
6.2.11 Refresh Time Constant Register (RTCOR) .........................................................
6.2.12 Address Control Register (ADRCR) ...................................................................
Operation ..........................................................................................................................
6.3.1 Area Division.......................................................................................................
6.3.2 Bus Specifications ...............................................................................................
6.3.3 Memory Interfaces...............................................................................................
6.3.4 Chip Select Signals ..............................................................................................
6.3.5 Address Output Method.......................................................................................
Basic Bus Interface ...........................................................................................................
6.4.1 Overview..............................................................................................................
6.4.2 Data Size and Data Alignment.............................................................................
6.4.3 Valid Strobes ......................................................................................................
6.4.4 Memory Areas .....................................................................................................
6.4.5 Basic Bus Control Signal Timing ........................................................................
6.4.6 Wait Control ........................................................................................................
DRAM Interface ...............................................................................................................
6.5.1 Overview..............................................................................................................
6.5.2 DRAM Space and RAS Output Pin Settings .......................................................
6.5.3 Address Multiplexing ..........................................................................................
6.5.4 Data Bus ..............................................................................................................
6.5.5 Pins Used for DRAM Interface ...........................................................................
6.5.6 Basic Timing........................................................................................................
6.5.7 Precharge State Control .......................................................................................
6.5.8 Wait Control ........................................................................................................
6.5.9 Byte Access Control and CAS Output Pin ..........................................................
6.5.10 Burst Operation....................................................................................................
6.5.11 Refresh Control....................................................................................................
6.5.12 Examples of Use ..................................................................................................
6.5.13 Usage Notes.........................................................................................................
Interval Timer ...................................................................................................................
6.6.1 Operation .............................................................................................................
Interrupt Sources...............................................................................................................
Burst ROM Interface ........................................................................................................
6.8.1 Overview..............................................................................................................
6.8.2 Basic Timing........................................................................................................
6.8.3 Wait Control ........................................................................................................
Idle Cycle..........................................................................................................................
6.9.1 Operation .............................................................................................................
Rev. 3.00 Sep 14, 2005 page x of xxii
135
136
137
138
139
139
141
142
143
144
146
146
146
147
148
150
157
159
159
159
160
161
162
162
164
165
166
168
174
178
183
186
186
192
192
192
192
193
194
194
6.9.2 Pin States in Idle Cycle........................................................................................
6.10 Bus Arbiter........................................................................................................................
6.10.1 Operation .............................................................................................................
6.11 Register and Pin Input Timing ..........................................................................................
6.11.1 Register Write Timing .........................................................................................
6.11.2 BREQ Pin Input Timing ......................................................................................
197
198
198
201
201
202
Section 7 DMA Controller ................................................................................................ 203
7.1
7.2
7.3
7.4
7.5
Overview...........................................................................................................................
7.1.1 Features................................................................................................................
7.1.2 Block Diagram.....................................................................................................
7.1.3 Functional Overview............................................................................................
7.1.4 Input/Output Pins.................................................................................................
7.1.5 Register Configuration.........................................................................................
Register Descriptions (1) (Short Address Mode)..............................................................
7.2.1 Memory Address Registers (MAR) .....................................................................
7.2.2 I/O Address Registers (IOAR).............................................................................
7.2.3 Execute Transfer Count Registers (ETCR)..........................................................
7.2.4 Data Transfer Control Registers (DTCR) ............................................................
Register Descriptions (2) (Full Address Mode) ................................................................
7.3.1 Memory Address Registers (MAR) .....................................................................
7.3.2 I/O Address Registers (IOAR).............................................................................
7.3.3 Execute Transfer Count Registers (ETCR)..........................................................
7.3.4 Data Transfer Control Registers (DTCR) ............................................................
Operation ..........................................................................................................................
7.4.1 Overview..............................................................................................................
7.4.2 I/O Mode..............................................................................................................
7.4.3 Idle Mode.............................................................................................................
7.4.4 Repeat Mode........................................................................................................
7.4.5 Normal Mode.......................................................................................................
7.4.6 Block Transfer Mode ...........................................................................................
7.4.7 DMAC Activation................................................................................................
7.4.8 DMAC Bus Cycle................................................................................................
7.4.9 Multiple-Channel Operation ................................................................................
7.4.10 External Bus Requests, DRAM Interface, and DMAC........................................
7.4.11 NMI Interrupts and DMAC .................................................................................
7.4.12 Aborting a DMAC Transfer.................................................................................
7.4.13 Exiting Full Address Mode..................................................................................
7.4.14 DMAC States in Reset State, Standby Modes, and Sleep Mode .........................
Interrupts...........................................................................................................................
203
203
204
205
206
207
208
208
209
210
211
214
214
214
215
217
223
223
225
227
230
234
237
242
244
250
251
252
253
254
255
256
Rev. 3.00 Sep 14, 2005 page xi of xxii
7.6
Usage Notes ......................................................................................................................
7.6.1 Note on Word Data Transfer ...............................................................................
7.6.2 DMAC Self-Access .............................................................................................
7.6.3 Longword Access to Memory Address Registers................................................
7.6.4 Note on Full Address Mode Setup.......................................................................
7.6.5 Note on Activating DMAC by Internal Interrupts ...............................................
7.6.6 NMI Interrupts and Block Transfer Mode ...........................................................
7.6.7 Memory and I/O Address Register Values ..........................................................
7.6.8 Bus Cycle when Transfer is Aborted ...................................................................
7.6.9 Transfer Requests by A/D Converter...................................................................
257
257
257
257
257
258
259
259
260
261
Section 8 I/O Ports .............................................................................................................. 263
8.1
8.2
Overview...........................................................................................................................
Port 1.................................................................................................................................
8.2.1 Overview..............................................................................................................
8.2.2 Register Descriptions...........................................................................................
8.3 Port 2.................................................................................................................................
8.3.1 Overview..............................................................................................................
8.3.2 Register Descriptions...........................................................................................
8.4 Port 3.................................................................................................................................
8.4.1 Overview..............................................................................................................
8.4.2 Register Descriptions...........................................................................................
8.5 Port 4.................................................................................................................................
8.5.1 Overview..............................................................................................................
8.5.2 Register Descriptions...........................................................................................
8.6 Port 5.................................................................................................................................
8.6.1 Overview..............................................................................................................
8.6.2 Register Descriptions...........................................................................................
8.7 Port 6.................................................................................................................................
8.7.1 Overview..............................................................................................................
8.7.2 Register Descriptions...........................................................................................
8.8 Port 7.................................................................................................................................
8.8.1 Overview..............................................................................................................
8.8.2 Register Description ............................................................................................
8.9 Port 8.................................................................................................................................
8.9.1 Overview..............................................................................................................
8.9.2 Register Descriptions...........................................................................................
8.10 Port 9.................................................................................................................................
8.10.1 Overview..............................................................................................................
8.10.2 Register Descriptions...........................................................................................
Rev. 3.00 Sep 14, 2005 page xii of xxii
263
266
266
267
269
269
270
273
273
273
275
275
276
279
279
280
283
283
284
287
287
288
289
289
291
295
295
296
8.11 Port A................................................................................................................................
8.11.1 Overview..............................................................................................................
8.11.2 Register Descriptions...........................................................................................
8.12 Port B ................................................................................................................................
8.12.1 Overview..............................................................................................................
8.12.2 Register Descriptions...........................................................................................
300
300
302
312
312
314
Section 9 16-Bit Timer....................................................................................................... 321
9.1
9.2
9.3
9.4
9.5
9.6
Overview...........................................................................................................................
9.1.1 Features................................................................................................................
9.1.2 Block Diagrams ...................................................................................................
9.1.3 Pin Configuration.................................................................................................
9.1.4 Register Configuration.........................................................................................
Register Descriptions........................................................................................................
9.2.1 Timer Start Register (TSTR) ...............................................................................
9.2.2 Timer Synchro Register (TSNC) .........................................................................
9.2.3 Timer Mode Register (TMDR)............................................................................
9.2.4 Timer Interrupt Status Register A (TISRA).........................................................
9.2.5 Timer Interrupt Status Register B (TISRB) .........................................................
9.2.6 Timer Interrupt Status Register C (TISRC) .........................................................
9.2.7 Timer Counters (16TCNT) ..................................................................................
9.2.8 General Registers (GRA, GRB)...........................................................................
9.2.9 Timer Control Registers (16TCR) .......................................................................
9.2.10 Timer I/O Control Register (TIOR).....................................................................
9.2.11 Timer Output Level Setting Register C (TOLR) .................................................
CPU Interface ...................................................................................................................
9.3.1 16-Bit Accessible Registers .................................................................................
9.3.2 8-Bit Accessible Registers ...................................................................................
Operation ..........................................................................................................................
9.4.1 Overview..............................................................................................................
9.4.2 Basic Functions....................................................................................................
9.4.3 Synchronization ...................................................................................................
9.4.4 PWM Mode .........................................................................................................
9.4.5 Phase Counting Mode..........................................................................................
9.4.6 16-Bit Timer Output Timing................................................................................
Interrupts...........................................................................................................................
9.5.1 Setting of Status Flags .........................................................................................
9.5.2 Timing of Clearing of Status Flags ......................................................................
9.5.3 Interrupt Sources..................................................................................................
Usage Notes ......................................................................................................................
321
321
323
326
327
328
328
329
331
333
336
339
341
342
343
346
348
350
350
352
353
353
354
361
363
367
369
370
370
372
373
374
Rev. 3.00 Sep 14, 2005 page xiii of xxii
Section 10 8-Bit Timers.....................................................................................................
10.1 Overview...........................................................................................................................
10.1.1 Features................................................................................................................
10.1.2 Block Diagram.....................................................................................................
10.1.3 Pin Configuration ................................................................................................
10.1.4 Register Configuration.........................................................................................
10.2 Register Descriptions........................................................................................................
10.2.1 Timer Counters (8TCNT) ....................................................................................
10.2.2 Time Constant Registers A (TCORA).................................................................
10.2.3 Time Constant Registers B (TCORB) .................................................................
10.2.4 Timer Control Register (8TCR)...........................................................................
10.2.5 Timer Control/Status Registers (8TCSR) ............................................................
10.3 CPU Interface ...................................................................................................................
10.3.1 8-Bit Registers .....................................................................................................
10.4 Operation ..........................................................................................................................
10.4.1 8TCNT Count Timing .........................................................................................
10.4.2 Compare Match Timing.......................................................................................
10.4.3 Input Capture Signal Timing ...............................................................................
10.4.4 Timing of Status Flag Setting ..............................................................................
10.4.5 Operation with Cascaded Connection..................................................................
10.4.6 Input Capture Setting...........................................................................................
10.5 Interrupt ............................................................................................................................
10.5.1 Interrupt Sources..................................................................................................
10.5.2 A/D Converter Activation....................................................................................
10.6 8-Bit Timer Application Example ....................................................................................
10.7 Usage Notes ......................................................................................................................
10.7.1 Contention between 8TCNT Write and Clear......................................................
10.7.2 Contention between 8TCNT Write and Increment ..............................................
10.7.3 Contention between TCOR Write and Compare Match ......................................
10.7.4 Contention between TCOR Read and Input Capture...........................................
10.7.5 Contention between Counter Clearing by Input Capture and Counter
Increment .............................................................................................................
10.7.6 Contention between TCOR Write and Input Capture ..........................................
10.7.7 Contention between 8TCNT Byte Write and Increment in 16-Bit Count Mode
(Cascaded Connection)........................................................................................
10.7.8 Contention between Compare Matches A and B .................................................
10.7.9 8TCNT Operation and Internal Clock Source Switchover ..................................
387
387
387
389
390
391
392
392
393
394
395
398
403
403
405
405
406
407
408
409
412
414
414
415
415
416
416
417
418
419
420
421
422
423
423
Section 11 Programmable Timing Pattern Controller (TPC) ................................. 427
11.1 Overview........................................................................................................................... 427
Rev. 3.00 Sep 14, 2005 page xiv of xxii
11.1.1 Features................................................................................................................
11.1.2 Block Diagram.....................................................................................................
11.1.3 TPC Pins ..............................................................................................................
11.1.4 Registers ..............................................................................................................
11.2 Register Descriptions........................................................................................................
11.2.1 Port A Data Direction Register (PADDR) ...........................................................
11.2.2 Port A Data Register (PADR)..............................................................................
11.2.3 Port B Data Direction Register (PBDDR) ...........................................................
11.2.4 Port B Data Register (PBDR) ..............................................................................
11.2.5 Next Data Register A (NDRA) ............................................................................
11.2.6 Next Data Register B (NDRB) ............................................................................
11.2.7 Next Data Enable Register A (NDERA)..............................................................
11.2.8 Next Data Enable Register B (NDERB) ...............................................................
11.2.9 TPC Output Control Register (TPCR) .................................................................
11.2.10 TPC Output Mode Register (TPMR)...................................................................
11.3 Operation ..........................................................................................................................
11.3.1 Overview..............................................................................................................
11.3.2 Output Timing......................................................................................................
11.3.3 Normal TPC Output.............................................................................................
11.3.4 Non-Overlapping TPC Output.............................................................................
11.3.5 TPC Output Triggering by Input Capture ............................................................
11.4 Usage Notes ......................................................................................................................
11.4.1 Operation of TPC Output Pins.............................................................................
11.4.2 Note on Non-Overlapping Output .......................................................................
427
428
429
430
431
431
431
432
432
433
435
437
438
439
442
444
444
445
446
448
450
451
451
451
Section 12 Watchdog Timer ............................................................................................. 453
12.1 Overview...........................................................................................................................
12.1.1 Features................................................................................................................
12.1.2 Block Diagram.....................................................................................................
12.1.3 Register Configuration.........................................................................................
12.2 Register Descriptions........................................................................................................
12.2.1 Timer Counter (TCNT)........................................................................................
12.2.2 Timer Control/Status Register (TCSR)................................................................
12.2.3 Reset Control/Status Register (RSTCSR)............................................................
12.2.4 Notes on Register Access ....................................................................................
12.3 Operation ..........................................................................................................................
12.3.1 Watchdog Timer Operation .................................................................................
12.3.2 Interval Timer Operation .....................................................................................
12.3.3 Timing of Setting of Overflow Flag (OVF).........................................................
12.3.4 Timing of Setting of Watchdog Timer Reset Bit (WRST) ..................................
453
453
454
454
455
455
456
458
459
461
461
462
463
464
Rev. 3.00 Sep 14, 2005 page xv of xxii
12.4 Interrupts........................................................................................................................... 465
12.5 Usage Notes ...................................................................................................................... 465
Section 13 Serial Communication Interface ................................................................
13.1 Overview...........................................................................................................................
13.1.1 Features................................................................................................................
13.1.2 Block Diagram.....................................................................................................
13.1.3 Input/Output Pins.................................................................................................
13.1.4 Register Configuration.........................................................................................
13.2 Register Descriptions........................................................................................................
13.2.1 Receive Shift Register (RSR) ..............................................................................
13.2.2 Receive Data Register (RDR)..............................................................................
13.2.3 Transmit Shift Register (TSR).............................................................................
13.2.4 Transmit Data Register (TDR) ............................................................................
13.2.5 Serial Mode Register (SMR) ...............................................................................
13.2.6 Serial Control Register (SCR) .............................................................................
13.2.7 Serial Status Register (SSR) ................................................................................
13.2.8 Bit Rate Register (BRR) ......................................................................................
13.3 Operation ..........................................................................................................................
13.3.1 Overview..............................................................................................................
13.3.2 Operation in Asynchronous Mode .......................................................................
13.3.3 Multiprocessor Communication ..........................................................................
13.3.4 Synchronous Operation .......................................................................................
13.4 SCI Interrupts....................................................................................................................
13.5 Usage Notes ......................................................................................................................
13.5.1 Notes on Use of SCI ............................................................................................
467
467
467
469
470
471
472
472
472
473
473
474
478
483
488
497
497
499
509
516
525
526
526
Section 14 Smart Card Interface .....................................................................................
14.1 Overview...........................................................................................................................
14.1.1 Features................................................................................................................
14.1.2 Block Diagram.....................................................................................................
14.1.3 Pin Configuration ................................................................................................
14.1.4 Register Configuration.........................................................................................
14.2 Register Descriptions........................................................................................................
14.2.1 Smart Card Mode Register (SCMR)....................................................................
14.2.2 Serial Status Register (SSR) ................................................................................
14.2.3 Serial Mode Register (SMR) ...............................................................................
14.2.4 Serial Control Register (SCR) .............................................................................
14.3 Operation ..........................................................................................................................
14.3.1 Overview..............................................................................................................
533
533
533
534
535
536
537
537
539
540
541
542
542
Rev. 3.00 Sep 14, 2005 page xvi of xxii
14.3.2 Pin Connections ...................................................................................................
14.3.3 Data Format .........................................................................................................
14.3.4 Register Settings ..................................................................................................
14.3.5 Clock....................................................................................................................
14.3.6 Transmitting and Receiving Data ........................................................................
14.4 Usage Notes ......................................................................................................................
542
544
545
547
549
557
Section 15 A/D Converter ................................................................................................. 561
15.1 Overview...........................................................................................................................
15.1.1 Features................................................................................................................
15.1.2 Block Diagram.....................................................................................................
15.1.3 Input Pins.............................................................................................................
15.1.4 Register Configuration.........................................................................................
15.2 Register Descriptions........................................................................................................
15.2.1 A/D Data Registers A to D (ADDRA to ADDRD) .............................................
15.2.2 A/D Control/Status Register (ADCSR) ...............................................................
15.2.3 A/D Control Register (ADCR) ............................................................................
15.3 CPU Interface ...................................................................................................................
15.4 Operation ..........................................................................................................................
15.4.1 Single Mode (SCAN = 0) ....................................................................................
15.4.2 Scan Mode (SCAN = 1).......................................................................................
15.4.3 Input Sampling and A/D Conversion Time .........................................................
15.4.4 External Trigger Input Timing.............................................................................
15.5 Interrupts...........................................................................................................................
15.6 Usage Notes ......................................................................................................................
561
561
562
563
564
565
565
566
569
570
572
572
574
576
578
579
579
Section 16 D/A Converter ................................................................................................. 585
16.1 Overview...........................................................................................................................
16.1.1 Features................................................................................................................
16.1.2 Block Diagram.....................................................................................................
16.1.3 Input/Output Pins.................................................................................................
16.1.4 Register Configuration.........................................................................................
16.2 Register Descriptions........................................................................................................
16.2.1 D/A Data Registers 0 and 1 (DADR0/1) .............................................................
16.2.2 D/A Control Register (DACR) ............................................................................
16.2.3 D/A Standby Control Register (DASTCR)..........................................................
16.3 Operation ..........................................................................................................................
16.4 D/A Output Control ..........................................................................................................
585
585
586
586
587
588
588
588
590
591
592
Rev. 3.00 Sep 14, 2005 page xvii of xxii
Section 17 RAM ..................................................................................................................
17.1 Overview...........................................................................................................................
17.1.1 Block Diagram.....................................................................................................
17.1.2 Register Configuration.........................................................................................
17.2 System Control Register (SYSCR) ...................................................................................
17.3 Operation ..........................................................................................................................
593
593
594
594
595
596
Section 18 Flash Memory ................................................................................................. 597
18.1 Overview........................................................................................................................... 597
18.2 Features............................................................................................................................. 598
18.2.1 Block Diagram..................................................................................................... 599
18.2.2 Pin Configuration ................................................................................................ 600
18.2.3 Register Configuration......................................................................................... 600
18.3 Register Descriptions........................................................................................................ 601
18.3.1 Flash Memory Control Register 1 (FLMCR1) .................................................... 601
18.3.2 Flash Memory Control Register 2 (FLMCR2) .................................................... 604
18.3.3 Erase Block Register 1 (EBR1) ........................................................................... 605
18.3.4 Erase Block Register 2 (EBR2) ........................................................................... 606
18.3.5 RAM Control Register (RAMCR)....................................................................... 607
18.4 Overview of Operation ..................................................................................................... 609
18.4.1 Mode Transitions ................................................................................................. 609
18.4.2 On-Board Programming Modes........................................................................... 611
18.4.3 Flash Memory Emulation in RAM ...................................................................... 613
18.4.4 Block Configuration ............................................................................................ 615
18.5 On-Board Programming Mode ......................................................................................... 616
18.5.1 Boot Mode ........................................................................................................... 617
18.5.2 User Program Mode............................................................................................. 622
18.6 Flash Memory Programming/Erasing............................................................................... 624
18.6.1 Program Mode ..................................................................................................... 626
18.6.2 Program-Verify Mode ......................................................................................... 627
18.6.3 Erase Mode .......................................................................................................... 631
18.6.4 Erase-Verify Mode .............................................................................................. 631
18.7 Flash Memory Protection.................................................................................................. 633
18.7.1 Hardware Protection ............................................................................................ 633
18.7.2 Software Protection ............................................................................................. 634
18.7.3 Error Protection ................................................................................................... 635
18.8 Flash Memory Emulation in RAM ................................................................................... 637
18.9 NMI Input Disabling Conditions ...................................................................................... 640
18.10 Flash Memory PROM Mode ............................................................................................ 641
18.10.1 Socket Adapters and Memory Map ..................................................................... 641
Rev. 3.00 Sep 14, 2005 page xviii of xxii
18.10.2 Notes on Use of PROM Mode ............................................................................. 642
18.11 Flash Memory Programming and Erasing Precautions..................................................... 643
Section 19 Clock Pulse Generator .................................................................................. 649
19.1 Overview...........................................................................................................................
19.1.1 Block Diagram.....................................................................................................
19.2 Oscillator Circuit...............................................................................................................
19.2.1 Connecting a Crystal Resonator...........................................................................
19.2.2 External Clock Input............................................................................................
19.3 Duty Adjustment Circuit...................................................................................................
19.4 Prescalers ..........................................................................................................................
19.5 Frequency Divider ............................................................................................................
19.5.1 Register Configuration.........................................................................................
19.5.2 Division Control Register (DIVCR) ....................................................................
19.5.3 Usage Notes .........................................................................................................
649
650
651
651
653
655
655
656
656
656
657
Section 20 Power-Down State ......................................................................................... 659
20.1 Overview........................................................................................................................... 659
20.2 Register Configuration...................................................................................................... 661
20.2.1 System Control Register (SYSCR) ...................................................................... 661
20.2.2 Module Standby Control Register H (MSTCRH)................................................ 663
20.2.3 Module Standby Control Register L (MSTCRL)................................................. 664
20.3 Sleep Mode ....................................................................................................................... 667
20.3.1 Transition to Sleep Mode..................................................................................... 667
20.3.2 Exit from Sleep Mode.......................................................................................... 667
20.4 Software Standby Mode.................................................................................................... 668
20.4.1 Transition to Software Standby Mode ................................................................. 668
20.4.2 Exit from Software Standby Mode ...................................................................... 668
20.4.3 Selection of Waiting Time for Exit from Software Standby Mode ..................... 669
20.4.4 Sample Application of Software Standby Mode.................................................. 670
20.4.5 Note ..................................................................................................................... 670
20.5 Hardware Standby Mode .................................................................................................. 671
20.5.1 Transition to Hardware Standby Mode................................................................ 671
20.5.2 Exit from Hardware Standby Mode..................................................................... 671
20.5.3 Timing for Hardware Standby Mode ................................................................... 671
20.6 Module Standby Function................................................................................................. 673
20.6.1 Module Standby Timing ...................................................................................... 673
20.6.2 Read/Write in Module Standby ........................................................................... 673
20.6.3 Usage Notes ......................................................................................................... 673
20.7 System Clock Output Disabling Function......................................................................... 674
Rev. 3.00 Sep 14, 2005 page xix of xxii
Section 21 Electrical Characteristics .............................................................................
21.1 Electrical Characteristics of H8/3068F-ZTAT..................................................................
21.1.1 Absolute Maximum Ratings ................................................................................
21.1.2 DC Characteristics ...............................................................................................
21.1.3 AC Characteristics ...............................................................................................
21.1.4 A/D Conversion Characteristics ..........................................................................
21.1.5 D/A Conversion Characteristics ..........................................................................
21.1.6 Flash Memory Characteristics .............................................................................
21.2 Operational Timing...........................................................................................................
21.2.1 Clock Timing .......................................................................................................
21.2.2 Control Signal Timing .........................................................................................
21.2.3 Bus Timing ..........................................................................................................
21.2.4 DRAM Interface Bus Timing ..............................................................................
21.2.5 TPC and I/O Port Timing.....................................................................................
21.2.6 Timer Input/Output Timing .................................................................................
21.2.7 SCI Input/Output Timing.....................................................................................
21.2.8 DMAC Timing.....................................................................................................
675
675
675
676
681
687
689
690
692
692
693
694
700
703
704
705
706
Appendix A Instruction Set .............................................................................................. 707
A.1
A.2
A.3
Instruction List.................................................................................................................. 707
Operation Code Maps ....................................................................................................... 723
Number of States Required for Execution ........................................................................ 726
Appendix B Internal I/O Registers .................................................................................
B.1 Addresses (EMC = 1) .........................................................................................................
B.2 Addresses (EMC = 0) .........................................................................................................
B.3 Functions ..........................................................................................................................
735
735
746
763
Appendix C I/O Port Block Diagrams .......................................................................... 854
C.1
C.2
C.3
C.4
C.5
C.6
C.7
C.8
C.9
C.10
C.11
Port 1 Block Diagram .......................................................................................................
Port 2 Block Diagram .......................................................................................................
Port 3 Block Diagram .......................................................................................................
Port 4 Block Diagram .......................................................................................................
Port 5 Block Diagram .......................................................................................................
Port 6 Block Diagrams......................................................................................................
Port 7 Block Diagrams......................................................................................................
Port 8 Block Diagrams......................................................................................................
Port 9 Block Diagrams......................................................................................................
Port A Block Diagrams.....................................................................................................
Port B Block Diagrams .....................................................................................................
Rev. 3.00 Sep 14, 2005 page xx of xxii
854
855
856
857
858
859
866
867
872
878
881
Appendix D Pin States ....................................................................................................... 889
D.1
D.2
Port States in Each Mode.................................................................................................. 889
Pin States at Reset............................................................................................................. 896
Appendix E Timing of Transition to and Recovery from Hardware Standby
Mode ............................................................................................................... 899
Appendix F Product Code Lineup .................................................................................. 900
Appendix G Package Dimensions .................................................................................. 901
Appendix H Comparison of H8/300H Series Product Specifications.................. 903
H.1
H.2
Differences between H8/3068F and H8/3067 Group and H8/3062 Group,
H8/3048 Group ................................................................................................................. 903
Comparison of Pin Functions of 100-Pin Package Products (FP-100B, TFP-100B)....... 906
Rev. 3.00 Sep 14, 2005 page xxi of xxii
Rev. 3.00 Sep 14, 2005 page xxii of xxii
Section 1 Overview
Section 1 Overview
1.1
Overview
The H8/3068F is a series of microcontrollers (MCUs) that integrate system supporting functions
together with an H8/300H CPU core having an original Renesas Technology architecture.
The H8/300H CPU has a 32-bit internal architecture with sixteen 16-bit general registers, and a
concise, optimized instruction set designed for speed. It can address a 16-Mbyte linear address
space. Its instruction set is upward-compatible at the object-code level with the H8/300 CPU,
enabling easy porting of software from the H8/300 Series.
The on-chip system supporting functions include ROM, RAM, a 16-bit timer, an 8-bit timer, a
programmable timing pattern controller (TPC), a watchdog timer (WDT), a serial communication
interface (SCI), an A/D converter, a D/A converter, I/O ports, a direct memory access controller
(DMAC), and other facilities.
The H8/3068F has 384 kbytes of ROM and 16 kbytes of RAM.
Seven MCU operating modes offer a choice of bus width and address space size. The modes
(modes 1 to 7) include two single-chip modes and five expanded modes.
The H8/3068F includes an F-ZTAT™* version with on-chip flash memory that can be
programmed on-board. This version enables users to respond quickly and flexibly to changing
application specifications, growing production volumes, and other conditions.
Table 1.1 summarizes the features of the H8/3068F.
Note: * F-ZTAT™ (Flexible ZTAT) is a trademark of Renesas Technology Corp.
Rev. 3.00 Sep 14, 2005 page 1 of 910
REJ09B0258-0300
Section 1 Overview
Table 1.1
Features
Feature
Description
CPU
Upward-compatible with the H8/300 CPU at the object-code level
General-register machine
•
Sixteen 16-bit general registers
(also usable as sixteen 8-bit registers or eight 32-bit registers)
High-speed operation
•
Maximum clock rate: 25 MHz
•
Add/subtract: 80 ns
•
Multiply/divide: 560 ns
16-Mbyte address space
Instruction features
Memory
•
8/16/32-bit data transfer, arithmetic, and logic instructions
•
Signed and unsigned multiply instructions (8 bits x 8 bits, 16 bits x 16 bits)
•
Signed and unsigned divide instructions (16 bits ÷ 8 bits, 32 bits ÷ 16 bits)
•
Bit accumulator function
•
Bit manipulation instructions with register-indirect specification of bit
positions
H8/3068F
•
ROM: 384 kbytes
•
RAM: 16 kbytes
Interrupt
•
Seven external interrupt pins: NMI, IRQ0 to IRQ5
controller
•
36 internal interrupts
•
Three selectable interrupt priority levels
•
Address space can be partitioned into eight areas, with independent bus
specifications in each area
•
Chip select output available for areas 0 to 7
•
8-bit access or 16-bit access selectable for each area
•
Two-state or three-state access selectable for each area
•
Selection of two wait modes
•
Number of program wait states selectable for each area
•
Direct connection of burst ROM
•
Direct connection of up to 8-Mbyte DRAM (or DRAM interface can be used
as interval timer)
•
Bus arbitration function
Bus controller
Rev. 3.00 Sep 14, 2005 page 2 of 910
REJ09B0258-0300
Section 1 Overview
Feature
Description
DMA controller
(DMAC)
Short address mode
•
Maximum four channels available
•
Selection of I/O mode, idle mode, or repeat mode
•
Can be activated by compare match/input capture A interrupts from 16-bit
timer channels 0 to 2, conversion-end interrupts from the A/D converter,
transmit-data-empty and receive-data-full interrupts from the SCI, or external
requests
Full address mode
16-bit timer,
3 channels
8-bit timer,
4 channels
Programmable
timing pattern
controller (TPC)
Watchdog
timer (WDT),
1 channel
•
Maximum two channels available
•
Selection of normal mode or block transfer mode
•
Can be activated by compare match/input capture A interrupts from 16-bit
timer channels 0 to 2, conversion-end interrupts from the A/D converter,
external requests, or auto-request
•
Three 16-bit timer channels, capable of processing up to six pulse outputs
or six pulse inputs
•
16-bit timer counter (channels 0 to 2)
•
Two multiplexed output compare/input capture pins (channels 0 to 2)
•
Operation can be synchronized (channels 0 to 2)
•
PWM mode available (channels 0 to 2)
•
Phase counting mode available (channel 2)
•
DMAC can be activated by compare match/input capture A interrupts
(channels 0 to 2)
•
8-bit up-counter (external event count capability)
•
Two time constant registers
•
Two channels can be connected
•
Maximum 16-bit pulse output, using 16-bit timer as time base
•
Up to four 4-bit pulse output groups (or one 16-bit group, or two 8-bit
groups)
•
Non-overlap mode available
•
Output data can be transferred by DMAC
•
Reset signal can be generated by overflow
•
Reset signal can be output externally (not in the F-ZTAT version)
•
Usable as an interval timer
Rev. 3.00 Sep 14, 2005 page 3 of 910
REJ09B0258-0300
Section 1 Overview
Feature
Description
Serial
communication
interface (SCI),
3 channels
•
Selection of asynchronous or synchronous mode
•
Full duplex: can transmit and receive simultaneously
•
On-chip baud-rate generator
•
Smart card interface functions added
•
Resolution: 10 bits
•
Eight channels, with selection of single or scan mode
A/D converter
D/A converter
I/O ports
•
Variable analog conversion voltage range
•
Sample-and-hold function
•
A/D conversion can be started by an external trigger or 8-bit timer comparematch
•
DMAC can be activated by an A/D conversion end interrupt
•
Resolution: 8 bits
•
Two channels
•
D/A outputs can be sustained in software standby mode
•
70 input/output pins
•
9 input-only pins
Operating modes •
Power-down
state
Other features
Seven MCU operating modes
Mode
Address Space
Address Pins
Initial Bus Width
Max. Bus Width
Mode 1
1 Mbyte
A19 to A0
8 bits
16 bits
Mode 2
1 Mbyte
A19 to A0
16 bits
16 bits
Mode 3
16 Mbytes
A23 to A0
8 bits
16 bits
Mode 4
16 Mbytes
A23 to A0
16 bits
16 bits
Mode 5
16 Mbytes
A23 to A0
8 bits
16 bits
Mode 6
64 kbyte
—
—
—
Mode 7
1 Mbyte
—
—
—
•
On-chip ROM is disabled in modes 1 to 4
•
Sleep mode
•
Software standby mode
•
Hardware standby mode
•
Module standby function
•
Programmable system clock frequency division
•
On-chip clock pulse generator
Rev. 3.00 Sep 14, 2005 page 4 of 910
REJ09B0258-0300
Section 1 Overview
Feature
Description
Product lineup
Product Type
Product Code
Package
H8/3068 F-ZTAT 5 V operation
HD64F3068F
100-pin QFP (FP-100B)
HD64F3068TE
100-pin TQFP (TFP-100B)
Rev. 3.00 Sep 14, 2005 page 5 of 910
REJ09B0258-0300
Section 1 Overview
1.2
Block Diagram
Port 3
P40 /D0
P41 /D1
P42 /D2
P43 /D3
P44 /D4
P45 /D5
P46 /D6
P47 /D7
P30 /D8
P31 /D9
P32 /D10
P33 /D11
P34 /D12
P35 /D13
P36 /D14
P37 /D15
VSS
VSS
VSS
VSS
VSS
VSS
VCC
VCC
VCL
Figure 1.1 shows an internal block diagram.
Port 4
Address bus
Data bus (upper)
MD1
Data bus (lower)
P53 /A 19
Port 5
MD2
MD0
P52 /A 18
P51 /A 17
P50 /A 16
EXTAL
P27 /A 15
Clock pulse
generator
RES
FWE
P26 /A 14
H8/300H CPU
P25 /A 13
Port 2
XTAL
STBY
NMI
LWR/P66
DMA controller
(DMAC)
RD/P64
AS/P63
Port 6
HWR/P65
P23 /A 11
P22 /A 10
Bus controller
Interrupt controller
φ/P67
P24 /A 12
P21 /A 9
P20 /A 8
P17 /A 7
ROM
(flash memory)
P16 /A 6
P15 /A 5
Port 1
BACK/P62
BREQ/P61
WAIT/P60
P14 /A 4
P13 /A 3
P12 /A 2
RAM
P11 /A 1
CS0/P84
CS2/IRQ2/P82
CS3/IRQ1/P81
Port 8
ADTRG/CS1/IRQ3/P83
P10 /A 0
Watchdog timer
(WDT)
16-bit timer unit
RFSH/IRQ0/P80
Serial communication
interface
(SCI) × 3 channels
8-bit timer unit
P95 /SCK 1 /IRQ 5
Programmable
timing pattern
controller (TPC)
P94 /SCK 0 /IRQ 4
Port 9
A/D converter
D/A converter
P93 /RxD1
P92 /RxD0
P91 /TxD 1
P90 /TxD 0
Figure 1.1 Block Diagram
Rev. 3.00 Sep 14, 2005 page 6 of 910
REJ09B0258-0300
AN0/P70
AN1/P71
AN2/P72
AN3/P73
AN4/P74
AN5/P75
DA0/AN6/P76
DA1/AN7/P77
AVSS
VREF
AVCC
TEND0/TCLKA/TP0/PA0
TEND1/TCLKB/TP1/PA1
Port 7
TCLKC/TIOCA0/TP2/PA2
TCLKD/TIOCB0/TP3/PA3
A23/TIOCA1/TP4/PA4
A22/TIOCB1/TP5/PA5
A21/TIOCA2/TP6/PA6
A20/TIOCB2/TP7/PA7
CS7/TMO0/TP8/PB0
CS6/DREQ0/TMIO1/TP9/PB1
Port A
CS5/TMO2/TP10/PB2
CS4/DREQ1/TMIO3/TP11/PB3
UCAS/TP12/PB4
TxD2/TP14/PB6
SCK2/LCAS/TP13/PB5
RxD2/TP15/PB7
Port B
Section 1 Overview
1.3
Pin Description
1.3.1
Pin Arrangement
P52 /A 18
P51 /A 17
P50 /A 16
P27 /A 15
P26 /A 14
54
53
52
51
STBY
62
P53 /A 19
RES
63
55
NMI
64
VSS
VSS
65
56
EXTAL
66
P60 /WAIT
XTAL
67
57
VCC
68
P61 /BREQ
P63 /AS
69
58
P64 /RD
70
59
P65 /HWR
71
P67/φ
P66 /LWR
72
P62 /BACK
MD0
73
60
MD1
74
61
MD2
75
The pin arrangement of the H8/3068F FP-100B and TFP-100B packages is shown in figure 1.2.
AVCC
76
50
A13/P25
VREF
77
49
A12/P24
P70/AN0
78
48
A11/P23
P71/AN1
79
47
A10/P22
P72/AN2
80
46
A9/P21
P73/AN3
81
45
A8/P20
P74/AN4
82
44
VSS
P75/AN5
83
43
A7/P17
P76/AN6/DA0
84
42
A6/P16
P77/AN7/DA1
85
41
A5/P15
AVSS
86
40
A4/P14
P80/IRQ0/RFSH
87
39
A3/P13
P81/IRQ1/CS3
88
38
A2/P12
P82/IRQ2/CS2
89
37
A1/P11
P83/IRQ3/CS1/ADTRG
90
36
A0/P10
P84/CS0
91
35
VCC
VSS
92
34
D15/P37
PA0/TP0/TCLKA/TEND0
93
33
D14/P36
PA1/TP1/TCLKB/TEND1
94
32
D13/P35
PA2/TP2/TIOCA0/TCLKC
95
31
D12/P34
PA3/TP3/TIOCB0/TCLKD
96
30
D11/P33
PA4/TP4/TIOCA1/A23
97
29
D10/P32
PA5/TP5/TIOCB1/A22
98
28
D9/P31
PA6/TP6/TIOCA2/A21
99
27
D8/P30
PA7/TP7/TIOCB2/A20
100
26
D7/P47
Top view
14
15
16
17
18
19
20
21
22
23
24
25
RxD1 /P93
IRQ4 /SCK0 /P94
IRQ5 /SCK1 /P95
D0 /P40
D1 /P41
D2 /P42
D3 /P43
VSS
D4 /P44
D5 /P45
D6 /P46
9
RxD2/TP15/PB7
RxD0 /P92
8
TxD2/TP14/PB6
13
7
SCK2/LCAS/TP13/PB5
TxD1 /P91
6
UCAS/TP12/PB4
12
5
CS4/DREQ1/TMIO3/TP11/PB3
TxD0 /P90
4
CS5/TMO2/TP10/PB2
11
3
CS6/DREQ0/TMIO1/TP9/PB1
10
2
FWE
VSS
1
VCL*
CS7/TMO0/TP8/PB0
(FP-100B, TFP-100B)
1
0.1 µF
Note: * Functions as VCL pin. When functioning as VCL pin, the connection of an external capacitor
is required.
Figure 1.2 Pin Arrangement (FP-100B or TFP-100B, Top View)
Rev. 3.00 Sep 14, 2005 page 7 of 910
REJ09B0258-0300
Section 1 Overview
1.3.2
Pin Functions
Table 1.2 summarizes the pin functions.
Table 1.2
Pin Functions
Pin No.
Type
Symbol
FP-100B
TFP-100B I/O
Power
VCC
35, 68
Input
Power: For connection to the power supply. Connect
all VCC pins to the system power supply.
VSS
11, 22, 44, Input
57, 65, 92
Ground: For connection to ground (0 V).
Connect all VSS pins to the 0-V system power supply.
XTAL
67
Input
For connection to a crystal resonator.
For examples of crystal resonator and external clock
input, see section 19, Clock Pulse Generator.
EXTAL
66
Input
For connection to a crystal resonator or input of an
external clock signal. For examples of crystal
resonator and external clock input, see section 19,
Clock Pulse Generator.
φ
61
Output System clock: Supplies the system clock to external
devices.
VCL
1
Output Connect an external capacitor between this pin and
GND (0 V). Do not connect to VCC.
Clock
Internal
step-down
pin
Name and Function
VCL
Operating
mode
control
MD2 to
MD0
75 to 73
Input
Mode 2 to mode 0: For setting the operating mode,
as follows. Inputs at these pins must not be changed
during operation.
MD2
Rev. 3.00 Sep 14, 2005 page 8 of 910
REJ09B0258-0300
0.1 µF
MD1
MD0
Operating Mode
0
0
0
—
0
0
1
Mode 1
0
1
0
Mode 2
0
1
1
Mode 3
1
0
0
Mode 4
1
0
1
Mode 5
1
1
0
Mode 6
1
1
1
Mode 7
Section 1 Overview
Pin No.
Type
Symbol
FP-100B
TFP-100B I/O
System
control
RES
63
Input
Reset input: When driven low, this pin resets the
chip
FWE
10
Input
Write enable signal: Flash memory write control
signal
STBY
62
Input
Standby: When driven low, this pin forces a
transition to hardware standby mode
BREQ
59
Input
Bus request: Used by an external bus master to
request the bus right
BACK
60
Output Bus request acknowledge: Indicates that the bus
has been granted to an external bus master
NMI
64
Input
Nonmaskable interrupt: Requests a
nonmaskable interrupt
17, 16,
90 to 87
Input
Interrupt request 5 to 0: Maskable interrupt request
pins
Interrupts
IRQ5
to
IRQ0
Name and Function
Address
bus
A23 to A0
97 to 100,
56 to 45,
43 to 36
Output Address bus: Outputs address signals
Data bus
D15 to D0
34 to 23,
21 to 18
Input/
output
Bus control
CS7
2 to 5,
88 to 91
Output Chip select: Select signals for areas 7 to 0
CS0
AS
69
Output Address strobe: Goes low to indicate valid address
output on the address bus
RD
70
Output Read: Goes low to indicate reading from the external
address space
HWR
71
Output High write: Goes low to indicate writing to the
external address space; indicates valid data on the
upper data bus (D15 to D8).
LWR
72
Output Low write: Goes low to indicate writing to the
external address space; indicates valid data on the
lower data bus (D7 to D0).
WAIT
58
Input
to
Data bus: Bidirectional data bus
Wait: Requests insertion of wait states in bus cycles
during access to the external address space
Rev. 3.00 Sep 14, 2005 page 9 of 910
REJ09B0258-0300
Section 1 Overview
Pin No.
Type
Symbol
FP-100B
TFP-100B I/O
DRAM
interface
RFSH
87
Output Refresh: Indicates a refresh cycle
CS5
89, 88,
5, 4
Output Row address strobe RAS: Row address strobe
signal for DRAM
RD
70
Output Write enable WE: Write enable signal for DRAM
HWR
71
6
Output Upper column address strobe UCAS: Column
address strobe signal for DRAM
72
7
Output Lower column address strobe LCAS: Column
address strobe signal for DRAM
5, 3
Input
94, 93
Output Transfer end 1 and 0: These signals indicate that
the DMAC has ended a data transfer
CS2
to
UCAS
LWR
LCAS
DMA
controller
(DMAC)
,
DREQ1
DREQ0
,
TEND1
TEND0
16-bit timer TCLKD to 96 to 93
TCLKA
8-bit timer
Programmable
timing
pattern
controller
(TPC)
Name and Function
DMA request 1 and 0: DMAC activation
requests
Input
Clock input D to A: External clock inputs
TIOCA2 to 99, 97, 95
TIOCA0
Input/
output
Input capture/output compare A2 to A0: GRA2 to
GRA0 output compare or input capture, or PWM
output
TIOCB2 to 100, 98,
TIOCB0
96
Input/
output
Input capture/output compare B2 to B0: GRB2 to
GRB0 output compare or input capture, or PWM
output
TMO0,
TMO2
2, 4
Output Compare match output: Compare match output
pins
TMIO1,
TMIO3
3, 5
Input/
output
Input capture input/compare match output: Input
capture input or compare match output pins
TCLKD to 96 to 93
TCLKA
Input
Counter external clock input: These pins input an
external clock to the counters.
TP15 to
TP0
Output TPC output 15 to 0: Pulse output
9 to 2,
100 to 93
Rev. 3.00 Sep 14, 2005 page 10 of 910
REJ09B0258-0300
Section 1 Overview
Pin No.
FP-100B
TFP-100B I/O
Type
Symbol
Serial communication
interface
(SCI)
TxD2 to
TxD0
8, 13, 12
Output Transmit data (channels 0, 1, 2): SCI data output
RxD2 to
RxD0
9, 15, 14
Input
Receive data (channels 0, 1, 2): SCI data input
SCK2 to
SCK0
7, 17, 16
Input/
output
Serial clock (channels 0, 1, 2): SCI clock
input/output
AN7 to
AN0
85 to 78
Input
Analog 7 to 0: Analog input pins
ADTRG
90
Input
A/D conversion external trigger input: External
trigger input for starting A/D conversion
D/A
converter
DA1, DA0
85, 84
Output Analog output: Analog output from the
D/A converter
A/D and
D/A
converters
AVCC
76
Input
Power supply pin for the A/D and D/A converters.
Connect to the system power supply when not using
the A/D and D/A converters.
AVSS
86
Input
Ground pin for the A/D and D/A converters. Connect
to system ground (0 V).
VREF
77
Input
Reference voltage input pin for the A/D and D/A
converters. Connect to the system power supply
when not using the A/D and D/A converters.
P17 to P10 43 to 36
Input/
output
Port 1: Eight input/output pins. The direction of each
pin can be selected in the port 1 data direction
register (P1DDR).
P27 to P20 52 to 45
Input/
output
Port 2: Eight input/output pins. The direction of each
pin can be selected in the port 2 data direction
register (P2DDR).
P37 to P30 34 to 27
Input/
output
Port 3: Eight input/output pins. The direction of each
pin can be selected in the port 3 data direction
register (P3DDR).
P47 to P40 26 to 23,
21 to 18
Input/
output
Port 4: Eight input/output pins. The direction of each
pin can be selected in the port 4 data direction
register (P4DDR).
P53 to P50 56 to 53
Input/
output
Port 5: Four input/output pins. The direction of each
pin can be selected in the port 5 data direction
register (P5DDR).
A/D
converter
I/O ports
Name and Function
Rev. 3.00 Sep 14, 2005 page 11 of 910
REJ09B0258-0300
Section 1 Overview
Pin No.
FP-100B
TFP-100B I/O
Type
Symbol
I/O ports
P67 to P60 61,
72 to 69,
60 to 58
Input/
output
Port 6: Eight input/output pins. The direction of each
pin can be selected in the port 6 data direction
register (P6DDR).
P77 to P70 85 to 78
Input
Port 7: Eight input pins
P84 to P80 91 to 87
Input/
output
Port 8: Five input/output pins. The direction of each
pin can be selected in the port 8 data direction
register (P8DDR).
P95 to P90 17 to 12
Input/
output
Port 9: Six input/output pins. The direction of each
pin can be selected in the port 9 data direction
register (P9DDR).
PA7 to PA0 100 to 93
Input/
output
Port A: Eight input/output pins. The direction of each
pin can be selected in the port A data direction
register (PADDR).
PB7 to PB0 9 to 2
Input/
output
Port B: Eight input/output pins. The direction of each
pin can be selected in the port B data direction
register (PBDDR).
Rev. 3.00 Sep 14, 2005 page 12 of 910
REJ09B0258-0300
Name and Function
Section 1 Overview
1.3.3
Pin Assignments in Each Mode
Table 1.3 lists the pin assignments in each mode.
Table 1.3
Pin No.
Pin Assignments in Each Mode (FP-100B or TFP-100B)
Pin Name
FP-100B
TFP-100B
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
1
VCL*1
VCL*1
VCL*1
VCL*1
VCL*1
VCL*1
VCL*1
2
PB0/TP8/
TMO0/CS7
PB0/TP8/
TMO0/CS7
PB0/TP8/
TMO0/CS7
PB0/TP8/
TMO0/CS7
PB0/TP8/
TMO0/CS7
PB0/TP8/
TMO0
PB0/TP8/
TMO0
3
PB1/TP9/
TMIO1/
DREQ0/
PB1/TP9/
TMIO1/
DREQ0/
PB1/TP9/
TMIO1/
DREQ0/
PB1/TP9/
TMIO1/
DREQ0/
PB1/TP9/
TMIO1/
DREQ0/
PB1/TP9/
TMIO1/
PB1/TP9/
TMIO1/
4
PB2/TP10/
TMO2/CS5
PB2/TP10/
TMO2/CS5
PB2/TP10/
TMO2/CS5
PB2/TP10/
TMO2/CS5
PB2/TP10/
TMO2/CS5
PB2/TP10/
TMO2
PB2/TP10/
TMO2
5
PB3/TP11/
TMIO3/
DREQ1/
PB3/TP11/
TMIO3/
DREQ1/
PB3/TP11/
TMIO3/
DREQ1/
PB3/TP11/
TMIO3/
DREQ1/
PB3/TP11/
TMIO3/
DREQ1/
PB3/TP11/
TMIO3/
PB3/TP11/
TMIO3/
6
PB4/TP12/
PB4/TP12/
PB4/TP12/
PB4/TP12/
PB4/TP12/
PB4/TP12
PB4/TP12
7
PB5/TP13/
LCAS/
SCK2
PB5/TP13/
LCAS/
SCK2
PB5/TP13/
LCAS/
SCK2
PB5/TP13/
LCAS/
SCK2
PB5/TP13/
LCAS/
SCK2
PB5/TP13/
SCK2
PB5/TP13/
SCK2
8
PB6/TP14/
TxD2
PB6/TP14/
TxD2
PB6/TP14/
TxD2
PB6/TP14/
TxD2
PB6/TP14/
TxD2
PB6/TP14/
TxD2
PB6/TP14/
TxD2
9
PB7/TP15/
RxD2
PB7/TP15/
RxD2
PB7/TP15/
RxD2
PB7/TP15/
RxD2
PB7/TP15/
RxD2
PB7/TP15/
RxD2
PB7/TP15/
RxD2
10
FWE
FWE
FWE
FWE
FWE
FWE
FWE
11
VSS
VSS
VSS
VSS
VSS
VSS
VSS
12
P90/TxD0
P90/TxD0
P90/TxD0
P90/TxD0
P90/TxD0
P90/TxD0
P90/TxD0
13
P91/TxD1
P91/TxD1
P91/TxD1
P91/TxD1
P91/TxD1
P91/TxD1
P91/TxD1
14
P92/RxD0
P92/RxD0
P92/RxD0
P92/RxD0
P92/RxD0
P92/RxD0
P92/RxD0
15
P93/RxD1
P93/RxD1
P93/RxD1
P93/RxD1
P93/RxD1
P93/RxD1
P93/RxD1
16
P94/IRQ4/
SCK0
P94/IRQ4/
SCK0
P94/IRQ4/
SCK0
P94/IRQ4/
SCK0
P94/IRQ4/
SCK0
P94/IRQ4/
SCK0
P94/IRQ4/
SCK0
CS6
CS4
UCAS
CS6
CS4
UCAS
CS6
CS4
UCAS
CS6
CS4
UCAS
CS6
CS4
UCAS
DREQ0
DREQ1
DREQ0
DREQ1
Rev. 3.00 Sep 14, 2005 page 13 of 910
REJ09B0258-0300
Section 1 Overview
Pin No.
Pin Name
FP-100B
TFP-100B
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
17
P95/IRQ5/
SCK1
P95/IRQ5/
SCK1
P95/IRQ5/
SCK1
P95/IRQ5/
SCK1
P95/IRQ5/
SCK1
P95/IRQ5/
SCK1
P95/IRQ5/
SCK1
18
P40/D0*
2
P40
P40
2
P41
P41
2
P42
P42
2
2
3
P40/D0*
2
P41/D1*
2
P42/D2*
19
P41/D1*
20
P42/D2*
2
2
P40/D0*
3
P41/D1*
3
P42/D2*
3
3
P40/D0*
2
P41/D1*
2
P42/D2*
2
P40/D0*
3
P41/D1*
3
P42/D2*
3
21
P43/D3*
P43/D3*
P43/D3*
P43/D3*
P43/D3*
P43
P43
22
VSS
VSS
VSS
VSS
VSS
23
24
2
P44/D4*
2
P45/D5*
3
P44/D4*
3
P45/D5*
2
P46/D6*
2
2
P44/D4*
2
P45/D5*
3
P46/D6*
3
3
P44/D4*
3
P45/D5*
2
P46/D6*
2
VSS
VSS
2
P44
P44
2
P45
P45
2
2
P44/D4*
P45/D5*
3
P46/D6*
3
25
P46/D6*
P46
P46
26
P47/D7*
P47/D7*
P47/D7*
P47/D7*
P47/D7*
P47
P47
27
D8
D8
D8
D8
D8
P30
P30
28
D9
D9
D9
D9
D9
P31
P31
29
D10
D10
D10
D10
D10
P32
P32
30
D11
D11
D11
D11
D11
P33
P33
31
D12
D12
D12
D12
D12
P34
P34
32
D13
D13
D13
D13
D13
P35
P35
33
D14
D14
D14
D14
D14
P36
P36
34
D15
D15
D15
D15
D15
P37
P37
35
VCC
VCC
VCC
VCC
VCC
VCC
VCC
36
A0
A0
A0
A0
P10/A0
P10
P10
37
A1
A1
A1
A1
P11/A1
P11
P11
38
A2
A2
A2
A2
P12/A2
P12
P12
39
A3
A3
A3
A3
P13/A3
P13
P13
40
A4
A4
A4
A4
P14/A4
P14
P14
41
A5
A5
A5
A5
P15/A5
P15
P15
42
A6
A6
A6
A6
P16/A6
P16
P16
43
A7
A7
A7
A7
P17/A7
P17
P17
44
VSS
VSS
VSS
VSS
VSS
VSS
VSS
45
A8
A8
A8
A8
P20/A8
P20
P20
46
A9
A9
A9
A9
P21/A9
P21
P21
47
A10
A10
A10
A10
P22/A10
P22
P22
Rev. 3.00 Sep 14, 2005 page 14 of 910
REJ09B0258-0300
Section 1 Overview
Pin No.
Pin Name
FP-100B
TFP-100B
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
48
A11
A11
A11
A11
P23/A11
P23
P23
49
A12
A12
A12
A12
P24/A12
P24
P24
50
A13
A13
A13
A13
P25/A13
P25
P25
51
A14
A14
A14
A14
P26/A14
P26
P26
52
A15
A15
A15
A15
P27/A15
P27
P27
53
A16
A16
A16
A16
P50/A16
P50
P50
54
A17
A17
A17
A17
P51/A17
P51
P51
55
A18
A18
A18
A18
P52/A18
P52
P52
56
A19
A19
A19
A19
P53/A19
P53
P53
57
VSS
VSS
VSS
VSS
VSS
VSS
VSS
58
P60/WAIT
P60/WAIT
P60/WAIT
P60/WAIT
P60/WAIT
P60
P60
59
P61/BREQ
P61/BREQ
P61/BREQ
P61/BREQ
P61/BREQ
P61
P61
60
P62/BACK
P62/BACK
P62/BACK
P62/BACK
P62/BACK
P62
P62
61
φ
φ
φ
φ
P67/φ
P67/φ
P67/φ
63
STBY
RES
STBY
RES
STBY
RES
STBY
RES
STBY
RES
STBY
RES
STBY
RES
64
NMI
NMI
NMI
NMI
NMI
NMI
NMI
65
VSS
VSS
VSS
VSS
VSS
VSS
VSS
66
EXTAL
EXTAL
EXTAL
EXTAL
EXTAL
EXTAL
EXTAL
67
XTAL
XTAL
XTAL
XTAL
XTAL
XTAL
XTAL
68
VCC
VCC
VCC
VCC
VCC
VCC
VCC
AS
RD
HWR
LWR
AS
RD
HWR
LWR
AS
RD
HWR
LWR
AS
RD
HWR
LWR
P63
P63
P64
P64
P65
P65
72
AS
RD
HWR
LWR
P66
P66
73
MD0
MD0
MD0
MD0
MD0
MD0
MD0
74
MD1
MD1
MD1
MD1
MD1
MD1
MD1
75
MD2
MD2
MD2
MD2
MD2
MD2
MD2
76
AVCC
AVCC
AVCC
AVCC
AVCC
AVCC
AVCC
77
VREF
VREF
VREF
VREF
VREF
VREF
VREF
78
P70/AN0
P70/AN0
P70/AN0
P70/AN0
P70/AN0
P70/AN0
P70/AN0
79
P71/AN1
P71/AN1
P71/AN1
P71/AN1
P71/AN1
P71/AN1
P71/AN1
62
69
70
71
Rev. 3.00 Sep 14, 2005 page 15 of 910
REJ09B0258-0300
Section 1 Overview
Pin No.
Pin Name
FP-100B
TFP-100B
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
80
P72/AN2
P72/AN2
P72/AN2
P72/AN2
P72/AN2
P72/AN2
P72/AN2
81
P73/AN3
P73/AN3
P73/AN3
P73/AN3
P73/AN3
P73/AN3
P73/AN3
82
P74/AN4
P74/AN4
P74/AN4
P74/AN4
P74/AN4
P74/AN4
P74/AN4
83
P75/AN5
P75/AN5
P75/AN5
P75/AN5
P75/AN5
P75/AN5
P75/AN5
84
P76/AN6/
DA0
P76/AN6/
DA0
P76/AN6/
DA0
P76/AN6/
DA0
P76/AN6/
DA0
P76/AN6/
DA0
P76/AN6/
DA0
85
P77/AN7/
DA1
P77/AN7/
DA1
P77/AN7/
DA1
P77/AN7/
DA1
P77/AN7/
DA1
P77/AN7/
DA1
P77/AN7/
DA1
86
AVSS
AVSS
AVSS
AVSS
AVSS
AVSS
AVSS
P80/IRQ0/
P80/IRQ0/
P80/IRQ0/
P80/IRQ0
P80/IRQ0
P81/IRQ1
P81/IRQ1
P82/IRQ2
P82/IRQ2
P83/IRQ3/
P83/IRQ3/
P84/CS0
RFSH
P81/IRQ1/
CS3
P82/IRQ2/
CS2
P83/IRQ3/
CS1/
ADTRG
P84/CS0
P80/IRQ0/
91
P80/IRQ0/
RFSH
P81/IRQ1/
CS3
P82/IRQ2/
CS2
P83/IRQ3/
CS1/
ADTRG
P84/CS0
P84
P84
92
VSS
VSS
VSS
VSS
VSS
VSS
VSS
93
PA0/TP0/
TCLKA/
PA0/TP0/
TCLKA/
PA0/TP0/
TCLKA/
PA0/TP0/
TCLKA/
PA0/TP0/
TCLKA/
PA0/TP0/
TCLKA/
PA0/TP0/
TCLKA/
PA1/TP1/
TCLKB/
PA1/TP1/
TCLKB/
PA1/TP1
/TCLKB/
PA1/TP1/
TCLKB/
PA1/TP1/
TCLKB/
PA1/TP1/
TCLKB/
PA1/TP1/
TCLKB/
95
PA2/TP2/
TIOCA0/
TCLKC
PA2/TP2/
TIOCA0/
TCLKC
PA2/TP2/
TIOCA0/
TCLKC
PA2/TP2/
TIOCA0/
TCLKC
PA2/TP2/
TIOCA0/
TCLKC
PA2/TP2/
TIOCA0/
TCLKC
PA2/TP2/
TIOCA0/
TCLKC
96
PA3/TP3/
TIOCB0/
TCLKD
PA3/TP3/
TIOCB0/
TCLKD
PA3/TP3/
TIOCB0/
TCLKD
PA3/TP3/
TIOCB0/
TCLKD
PA3/TP3/
TIOCB0/
TCLKD
PA3/TP3/
TIOCB0/
TCLKD
PA3/TP3/
TIOCB0/
TCLKD
97
PA4/TP4/
TIOCA1
PA4/TP4/
TIOCA1
PA4/TP4/
TIOCA1/
A23
PA4/TP4/
TIOCA1/
A23
PA4/TP4/
TIOCA1/
A23
PA4/TP4/
TIOCA1
PA4/TP4/
TIOCA1
87
88
89
90
TEND0
94
TEND1
RFSH
P81/IRQ1/
CS3
P82/IRQ2/
CS2
P83/IRQ3/
CS1/
ADTRG
P84/CS0
TEND0
TEND1
RFSH
P81/IRQ1/
CS3
P82/IRQ2/
CS2
P83/IRQ3/
CS1/ ADTRG
TEND0
TEND1
Rev. 3.00 Sep 14, 2005 page 16 of 910
REJ09B0258-0300
TEND0
TEND1
RFSH
P81/IRQ1/
CS3
P82/IRQ2/
CS2
P83/IRQ3/
CS1/
ADTRG
P84/CS0
TEND0
TEND1
ADTRG
TEND0
TEND1
ADTRG
TEND0
TEND1
Section 1 Overview
Pin No.
Pin Name
FP-100B
TFP-100B
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
98
PA5/TP5/
TIOCB1
PA5/TP5/
TIOCB1
PA5/TP5/
TIOCB1/
A22
PA5/TP5/
TIOCB1/
A22
PA5/TP5/
TIOCB1/
A22
PA5/TP5/
TIOCB1
PA5/TP5/
TIOCB1
99
PA6/TP6/
TIOCA2
PA6/TP6/
TIOCA2
PA6/TP6/
TIOCA2/
A21
PA6/TP6/
TIOCA2/
A21
PA6/TP6/
TIOCA2/
A21
PA6/TP6/
TIOCA2
PA6/TP6/
TIOCA2
100
PA7/TP7/
TIOCB2
PA7/TP7/
TIOCB2
A20
A20
PA7/TP7/
TIOCB2/
A20
PA7/TP7/
TIOCB2
PA7/TP7/
TIOCB2
Notes: 1. Functions as VCL pin.
2. In modes 1, 3, 5 the P40 to P47 functions of pins P40/D0 to P47/D7 are selected after a
reset, but they can be changed by software.
3. In modes 2 and 4 the D0 to D7 functions of pins P40/D0 to P47/D7 are selected after a
reset, but they can be changed by software.
Rev. 3.00 Sep 14, 2005 page 17 of 910
REJ09B0258-0300
Section 1 Overview
Rev. 3.00 Sep 14, 2005 page 18 of 910
REJ09B0258-0300
Section 2 CPU
Section 2 CPU
2.1
Overview
The H8/300H CPU is a high-speed central processing unit with an internal 32-bit architecture that
is upward-compatible with the H8/300 CPU. The H8/300H CPU has sixteen 16-bit general
registers, can address a 16-Mbyte linear address space, and is ideal for realtime control.
2.1.1
Features
The H8/300H CPU has the following features.
• Upward compatibility with H8/300 CPU
Can execute H8/300 Series object programs
• General-register architecture
Sixteen 16-bit general registers (also usable as sixteen 8-bit registers or eight 32-bit registers)
• Sixty-two basic instructions
 8/16/32-bit arithmetic and logic instructions
 Multiply and divide instructions
 Powerful bit-manipulation instructions
• Eight addressing modes
 Register direct [Rn]
 Register indirect [@ERn]
 Register indirect with displacement [@(d:16, ERn) or @(d:24, ERn)]
 Register indirect with post-increment or pre-decrement [@ERn+ or @–ERn]
 Absolute address [@aa:8, @aa:16, or @aa:24]
 Immediate [#xx:8, #xx:16, or #xx:32]
 Program-counter relative [@(d:8, PC) or @(d:16, PC)]
 Memory indirect [@@aa:8]
• 16-Mbyte linear address space
Rev. 3.00 Sep 14, 2005 page 19 of 910
REJ09B0258-0300
Section 2 CPU
• High-speed operation
 All frequently-used instructions execute in two to four states
 Maximum clock frequency:
25 MHz
 8/16/32-bit register-register add/subtract: 80 ns
 8 × 8-bit register-register multiply: 560 ns
 16 ÷ 8-bit register-register divide: 560 ns
 16 × 16-bit register-register multiply:
880 ns
 32 ÷ 16-bit register-register divide: 880 ns
• Two CPU operating modes
 Normal mode
 Advanced mode
• Low-power mode
Transition to power-down state by SLEEP instruction
2.1.2
Differences from H8/300 CPU
In comparison to the H8/300 CPU, the H8/300H has the following enhancements.
• More general registers
Eight 16-bit registers have been added.
• Expanded address space
 Advanced mode supports a maximum 16-Mbyte address space.
 Normal mode supports the same 64-kbyte address space as the H8/300 CPU.
• Enhanced addressing
The addressing modes have been enhanced to make effective use of the 16-Mbyte address
space.
• Enhanced instructions
 Data transfer, arithmetic, and logic instructions can operate on 32-bit data.
 Signed multiply/divide instructions and other instructions have been added.
Rev. 3.00 Sep 14, 2005 page 20 of 910
REJ09B0258-0300
Section 2 CPU
2.2
CPU Operating Modes
The H8/300H CPU has two operating modes: normal and advanced. Normal mode supports a
maximum 64-kbyte address space. Advanced mode supports up to 16 Mbytes.
Normal mode
Maximum 64 kbytes, program
and data areas combined
Advanced mode
Maximum 16 Mbytes, program
and data areas combined
CPU operating modes
Figure 2.1 CPU Operating Modes
Rev. 3.00 Sep 14, 2005 page 21 of 910
REJ09B0258-0300
Section 2 CPU
2.3
Address Space
Figure 2.2 shows a simple memory map for the H8/3068F. The H8/300H CPU can address a
linear address space with a maximum size of 64 kbytes in normal mode, and 16 Mbytes in
advanced mode. For further details see section 3.6, Memory Map in Each Operating Mode.
The 1-Mbyte operating modes use 20-bit addressing. The upper 4 bits of effective addresses are
ignored.
H'0000
H'00000
H'000000
H'FFFF
H'FFFFF
H'FFFFFF
a. 1-Mbyte mode
Normal mode
b. 16-Mbyte mode
Advanced mode
Figure 2.2 Memory Map
Rev. 3.00 Sep 14, 2005 page 22 of 910
REJ09B0258-0300
Section 2 CPU
2.4
Register Configuration
2.4.1
Overview
The H8/300H CPU has the internal registers shown in figure 2.3. There are two types of registers:
general registers and control registers.
General Registers (ERn)
15
0 7
0 7
0
ER0
E0
R0H
R0L
ER1
E1
R1H
R1L
ER2
E2
R2H
R2L
ER3
E3
R3H
R3L
ER4
E4
R4H
R4L
ER5
E5
R5H
R5L
ER6
E6
R6H
R6L
R7H
R7L
(SP)
E7
ER7
Control Registers (CR)
23
0
PC
7 6 5 4 3 2 1 0
CCR I UI H U N Z V C
Legend
SP: Stack pointer
PC: Program counter
CCR: Condition code register
Interrupt mask bit
I:
User bit or interrupt mask bit
UI:
Half-carry flag
H:
User bit
U:
Negative flag
N:
Zero flag
Z:
Overflow flag
V:
Carry flag
C:
Figure 2.3 CPU Registers
Rev. 3.00 Sep 14, 2005 page 23 of 910
REJ09B0258-0300
Section 2 CPU
2.4.2
General Registers
The H8/300H CPU has eight 32-bit general registers. These general registers are all functionally
alike and can be used without distinction between data registers and address registers. When a
general register is used as a data register, it can be accessed as a 32-bit, 16-bit, or 8-bit register.
When the general registers are used as 32-bit registers or as address registers, they are designated
by the letters ER (ER0 to ER7).
The ER registers divide into 16-bit general registers designated by the letters E (E0 to E7) and R
(R0 to R7). These registers are functionally equivalent, providing a maximum sixteen 16-bit
registers. The E registers (E0 to E7) are also referred to as extended registers.
The R registers divide into 8-bit general registers designated by the letters RH (R0H to R7H) and
RL (R0L to R7L). These registers are functionally equivalent, providing a maximum sixteen 8-bit
registers.
Figure 2.4 illustrates the usage of the general registers. The usage of each register can be selected
independently.
• Address registers
• 32-bit registers
• 16-bit registers
• 8-bit registers
E registers
(extended registers)
E0 to E7
RH registers
R0H to R7H
ER registers
ER0 to ER7
R registers
R0 to R7
RL registers
R0L to R7L
Figure 2.4 Usage of General Registers
Rev. 3.00 Sep 14, 2005 page 24 of 910
REJ09B0258-0300
Section 2 CPU
General register ER7 has the function of stack pointer (SP) in addition to its general-register
function, and is used implicitly in exception handling and subroutine calls. Figure 2.5 shows the
stack.
Free area
SP (ER7)
Stack area
Figure 2.5 Stack
2.4.3
Control Registers
The control registers are the 24-bit program counter (PC) and the 8-bit condition code register
(CCR).
Program Counter (PC): This 24-bit counter indicates the address of the next instruction the
CPU will execute. The length of all CPU instructions is 2 bytes (one word), so the least
significant PC bit is ignored. When an instruction is fetched, the least significant PC bit is
regarded as 0.
Condition Code Register (CCR): This 8-bit register contains internal CPU status information,
including the interrupt mask bit (I) and half-carry (H), negative (N), zero (Z), overflow (V), and
carry (C) flags.
Bit 7—Interrupt Mask Bit (I): Masks interrupts other than NMI when set to 1. NMI is accepted
regardless of the I bit setting. The I bit is set to 1 at the start of an exception-handling sequence.
Bit 6—User Bit or Interrupt Mask Bit (UI): Can be written and read by software using the
LDC, STC, ANDC, ORC, and XORC instructions. This bit can also be used as an interrupt mask
bit. For details see section 5, Interrupt Controller.
Bit 5—Half-Carry Flag (H): When the ADD.B, ADDX.B, SUB.B, SUBX.B, CMP.B, or NEG.B
instruction is executed, this flag is set to 1 if there is a carry or borrow at bit 3, and cleared to 0
otherwise. When the ADD.W, SUB.W, CMP.W, or NEG.W instruction is executed, the H flag is
set to 1 if there is a carry or borrow at bit 11, and cleared to 0 otherwise. When the ADD.L,
SUB.L, CMP.L, or NEG.L instruction is executed, the H flag is set to 1 if there is a carry or
borrow at bit 27, and cleared to 0 otherwise.
Rev. 3.00 Sep 14, 2005 page 25 of 910
REJ09B0258-0300
Section 2 CPU
Bit 4—User Bit (U): Can be written and read by software using the LDC, STC, ANDC, ORC,
and XORC instructions.
Bit 3—Negative Flag (N): Stores the value of the most significant bit of data, regarded as the
sign bit.
Bit 2—Zero Flag (Z): Set to 1 to indicate zero data, and cleared to 0 to indicate non-zero data.
Bit 1—Overflow Flag (V): Set to 1 when an arithmetic overflow occurs, and cleared to 0 at
other times.
Bit 0—Carry Flag (C): Set to 1 when a carry is generated by execution of an operation, and
cleared to 0 otherwise. Used by:
• Add instructions, to indicate a carry
• Subtract instructions, to indicate a borrow
• Shift and rotate instructions
The carry flag is also used as a bit accumulator by bit manipulation instructions.
Some instructions leave flag bits unchanged. Operations can be performed on CCR by the LDC,
STC, ANDC, ORC, and XORC instructions. The N, Z, V, and C flags are used by conditional
branch (Bcc) instructions.
For the action of each instruction on the flag bits, see appendix A.1, Instruction List. For the I and
UI bits, see section 5, Interrupt Controller.
2.4.4
Initial CPU Register Values
In reset exception handling, PC is initialized to a value loaded from the vector table, and the I bit
in CCR is set to 1. The other CCR bits and the general registers are not initialized. In particular,
the initial value of the stack pointer (ER7) is also undefined. The stack pointer (ER7) must
therefore be initialized by an MOV.L instruction executed immediately after a reset.
Rev. 3.00 Sep 14, 2005 page 26 of 910
REJ09B0258-0300
Section 2 CPU
2.5
Data Formats
The H8/300H CPU can process 1-bit, 4-bit (BCD), 8-bit (byte), 16-bit (word), and 32-bit
(longword) data. Bit-manipulation instructions operate on 1-bit data by accessing bit n (n = 0, 1,
2, …, 7) of byte operand data. The DAA and DAS decimal-adjust instructions treat byte data as
two digits of 4-bit BCD data.
2.5.1
General Register Data Formats
Figures 2.6 and 2.7 show the data formats in general registers.
Data Type
General
Register
1-bit data
RnH
7 6 5 4 3 2 1 0
1-bit data
RnL
Don’t care
4-bit BCD data
RnH
Upper digit Lower digit
4-bit BCD data
RnL
Don’t care
Byte data
RnH
Data Format
7
0
Don’t care
7
7
4 3
0
Don’t care
7
7
RnL
4 3
0
Upper digit Lower digit
0
Don’t care
MSB
Byte data
0
7 6 5 4 3 2 1 0
LSB
7
0
MSB
LSB
Don’t care
Legend
RnH: General register RH
RnL: General register RL
Figure 2.6 General Register Data Formats
Rev. 3.00 Sep 14, 2005 page 27 of 910
REJ09B0258-0300
Section 2 CPU
Data Type
General
Register
Word data
Rn
Word data
Data Format
15
0
MSB
LSB
15
0
MSB
LSB
En
31
16 15
0
Longword data ERn
MSB
Legend
ERn: General register
En:
General register E
Rn:
General register R
MSB: Most significant bit
LSB: Least significant bit
Figure 2.7 General Register Data Formats
Rev. 3.00 Sep 14, 2005 page 28 of 910
REJ09B0258-0300
LSB
Section 2 CPU
2.5.2
Memory Data Formats
Figure 2.8 shows the data formats on memory. The H8/300H CPU can access word data and
longword data on memory, but word or longword data must begin at an even address. If an
attempt is made to access word or longword data at an odd address, no address error occurs but
the least significant bit of the address is regarded as 0, so the access starts at the preceding
address. This also applies to instruction fetches.
Data Type
Address
Data Format
7
1-bit data
Address L
7
Byte data
Address L
MSB
Word data
Address 2M
MSB
0
6
5
4
Address 2N
2
1
0
LSB
Address 2M + 1
Longword data
3
LSB
MSB
Address 2N + 1
Address 2N + 2
Address 2N + 3
LSB
Figure 2.8 Memory Data Formats
When ER7 (SP) is used as an address register to access the stack, the operand size should be word
size or longword size.
Rev. 3.00 Sep 14, 2005 page 29 of 910
REJ09B0258-0300
Section 2 CPU
2.6
Instruction Set
2.6.1
Instruction Set Overview
The H8/300H CPU has 62 types of instructions, which are classified in table 2.1.
Table 2.1
Instruction Classification
Function
Data transfer
Instruction
Types
1
1
2
MOV, PUSH* , POP* , MOVTPE* , MOVFPE*
2
3
Arithmetic operations ADD, SUB, ADDX, SUBX, INC, DEC, ADDS, SUBS, DAA, DAS, 18
MULXU, MULXS, DIVXU, DIVXS, CMP, NEG, EXTS, EXTU
Logic operations
AND, OR, XOR, NOT
4
Shift operations
SHAL, SHAR, SHLL, SHLR, ROTL, ROTR, ROTXL, ROTXR
8
Bit manipulation
BSET, BCLR, BNOT, BTST, BAND, BIAND, BOR, BIOR, BXOR, 14
BIXOR, BLD, BILD, BST, BIST
Branch
Bcc*3, JMP, BSR, JSR, RTS
5
System control
TRAPA, RTE, SLEEP, LDC, STC, ANDC, ORC, XORC, NOP
9
Block data transfer
EEPMOV
1
Total 62 types
Notes: 1. POP.W Rn is identical to MOV.W @SP+, Rn.
PUSH.W Rn is identical to MOV.W Rn, @–SP.
POP.L ERn is identical to MOV.L @SP+, Rn.
PUSH.L ERn is identical to MOV.L Rn, @–SP.
2. Not available in the H8/3068F.
3. Bcc is a generic branching instruction.
Rev. 3.00 Sep 14, 2005 page 30 of 910
REJ09B0258-0300
Section 2 CPU
2.6.2
Instructions and Addressing Modes
Table 2.2 indicates the instructions available in the H8/300H CPU.
Table 2.2
Instructions and Addressing Modes
Addressing Modes
@
(d:24,
ERn)
@ERn+/
@–ERn
@
aa:8
@
aa:16
@
aa:24
@
(d:8,
PC)
@
(d:16,
PC)
@@
aa:8
Function
Instruction
#xx
Rn
@ERn
@
(d:16,
ERn)
Data
transfer
MOV
BWL
BWL
BWL
BWL
BWL
BWL
B
BWL
BWL
—
—
—
—
POP, PUSH
—
—
—
—
—
—
—
—
—
—
—
—
WL
MOVFPE,
—
—
—
—
—
—
—
—
—
—
—
—
—
—
MOVTPE
ADD, CMP
BWL
BWL
—
—
—
—
—
—
—
—
—
—
—
SUB
WL
BWL
—
—
—
—
—
—
—
—
—
—
—
ADDX, SUBX
B
B
—
—
—
—
—
—
—
—
—
—
—
ADDS, SUBS
—
L
—
—
—
—
—
—
—
—
—
—
—
INC, DEC
—
BWL
—
—
—
—
—
—
—
—
—
—
—
DAA, DAS
—
B
—
—
—
—
—
—
—
—
—
—
—
MULXU,
—
BW
—
—
—
—
—
—
—
—
—
—
—
NEG
—
BWL
—
—
—
—
—
—
—
—
—
—
—
EXTU, EXTS
—
WL
—
—
—
—
—
—
—
—
—
—
—
AND, OR, XOR
—
BWL
—
—
—
—
—
—
—
—
—
—
—
NOT
—
BWL
—
—
—
—
—
—
—
—
—
—
—
Shift instructions
—
BWL
—
—
—
—
—
—
—
—
—
—
—
Bit manipulation
—
B
B
—
—
—
B
—
—
—
—
—
—
Branch
Bcc, BSR
—
—
—
—
—
—
—
—
—
—
—
—
—
JMP, JSR
—
—
—
—
—
—
—
—
—
—
RTS
—
—
—
—
—
—
—
—
—
—
TRAPA
—
—
—
—
—
—
—
—
—
—
—
—
RTE
—
—
—
—
—
—
—
—
—
—
—
—
SLEEP
—
—
—
—
—
—
—
—
—
—
—
—
LDC
B
B
W
W
W
W
—
W
W
—
—
—
STC
—
B
W
W
W
W
—
W
W
—
—
—
—
ANDC, ORC,
XORC
B
—
—
—
—
—
—
—
—
—
—
—
—
NOP
—
—
—
—
—
—
—
—
—
—
—
—
Block data transfer
—
—
—
—
—
—
—
—
—
—
—
—
Arithmetic
operations
MULXS,
DIVXU,
DIVXS
Logic
operations
System
control
—
BW
Rev. 3.00 Sep 14, 2005 page 31 of 910
REJ09B0258-0300
Section 2 CPU
2.6.3
Tables of Instructions Classified by Function
Tables 2.3 to 2.10 summarize the instructions in each functional category. The operation notation
used in these tables is defined next.
Operation Notation
Rd
General register (destination)*
Rs
General register (source)*
Rn
General register*
ERn
General register (32-bit register or address register)
(EAd)
Destination operand
(EAs)
Source operand
CCR
Condition code register
N
N (negative) flag of CCR
Z
Z (zero) flag of CCR
V
V (overflow) flag of CCR
C
C (carry) flag of CCR
PC
Program counter
SP
Stack pointer
#IMM
Immediate data
disp
Displacement
+
Addition
–
Subtraction
×
Multiplication
÷
Division
∧
AND logical
∨
OR logical
⊕
Exclusive OR logical
→
Move
¬
NOT (logical complement)
:3/:8/:16/:24
3-, 8-, 16-, or 24-bit length
Note: * General registers include 8-bit registers (R0H to R7H, R0L to R7L), 16-bit registers (R0 to
R7, E0 to E7), and 32-bit data or address registers (ER0 to ER7).
Rev. 3.00 Sep 14, 2005 page 32 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.3
Data Transfer Instructions
Instruction Size*
Function
MOV
(EAs) → Rd, Rs → (EAd)
B/W/L
Moves data between two general registers or between a general register and
memory, or moves immediate data to a general register.
MOVFPE
B
(EAs) → Rd
Cannot be used in this LSI.
MOVTPE
B
Rs → (EAs)
Cannot be used in this LSI.
POP
W/L
@SP+ → Rn
Pops a general register from the stack. POP.W Rn is identical to MOV.W
@SP+, Rn. Similarly, POP.L ERn is identical to MOV.L @SP+, ERn.
PUSH
W/L
Rn → @–SP
Pushes a general register onto the stack. PUSH.W Rn is identical to MOV.W
Rn, @–SP. Similarly, PUSH.L ERn is identical to MOV.L ERn, @–SP.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
Rev. 3.00 Sep 14, 2005 page 33 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.4
Arithmetic Operation Instructions
Instruction Size*
Function
ADD,SUB
Rd ± Rs → Rd, Rd ± #IMM → Rd
B/W/L
Performs addition or subtraction on data in two general registers, or on
immediate data and data in a general register. (Immediate byte data cannot
be subtracted from data in a general register. Use the SUBX or ADD
instruction.)
ADDX,
SUBX
B
INC,
DEC
B/W/L
ADDS,
SUBS
L
DAA,
DAS
B
MULXU
B/W
Rd ± Rs ± C → Rd, Rd ± #IMM ± C → Rd
Performs addition or subtraction with carry or borrow on data in two general
registers, or on immediate data and data in a general register.
Rd ± 1 → Rd, Rd ± 2 → Rd
Increments or decrements a general register by 1 or 2. (Byte operands can
be incremented or decremented by 1 only.)
Rd ± 1 → Rd, Rd ± 2 → Rd, Rd ± 4 → Rd
Adds or subtracts the value 1, 2, or 4 to or from data in a 32-bit register.
Rd decimal adjust → Rd
Decimal-adjusts an addition or subtraction result in a general register by
referring to CCR to produce 4-bit BCD data.
Rd × Rs → Rd
Performs unsigned multiplication on data in two general registers:
either 8 bits × 8 bits → 16 bits or 16 bits × 16 bits → 32 bits.
MULXS
B/W
Rd × Rs → Rd
Performs signed multiplication on data in two general registers:
either 8 bits × 8 bits → 16 bits or 16 bits × 16 bits → 32 bits.
DIVXU
B/W
Rd ÷ Rs → Rd
Performs unsigned division on data in two general registers: either 16 bits ÷
8 bits → 8-bit quotient and 8-bit remainder or 32 bits ÷ 16 bits → 16-bit
quotient and 16-bit remainder
DIVXS
B/W
Rd ÷ Rs → Rd
Performs signed division on data in two general registers: either 16 bits ÷ 8
bits → 8-bit quotient and 8-bit remainder, or 32 bits ÷ 16 bits → 16-bit
quotient and 16-bit remainder
CMP
B/W/L
Rd – Rs, Rd – #IMM
Compares data in a general register with data in another general register or
with immediate data, and sets CCR according to the result.
NEG
B/W/L
0 – Rd → Rd
Takes the two’s complement (arithmetic complement) of data in a general
register.
Rev. 3.00 Sep 14, 2005 page 34 of 910
REJ09B0258-0300
Section 2 CPU
Instruction Size*
Function
EXTS
Rd (sign extension) → Rd
W/L
Extends byte data in the lower 8 bits of a 16-bit register to word data, or
extends word data in the lower 16 bits of a 32-bit register to longword data,
by extending the sign bit.
EXTU
W/L
Rd (zero extension) → Rd
Extends byte data in the lower 8 bits of a 16-bit register to word data, or
extends word data in the lower 16 bits of a 32-bit register to longword data,
by padding with zeros.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
Table 2.5
Logic Operation Instructions
Instruction Size*
Function
AND
Rd ∧ Rs → Rd, Rd ∧ #IMM → Rd
B/W/L
Performs a logical AND operation on a general register and another general
register or immediate data.
OR
B/W/L
Rd ∨ Rs → Rd, Rd ∨ #IMM → Rd
Performs a logical OR operation on a general register and another general
register or immediate data.
XOR
B/W/L
Rd ⊕ Rs → Rd, Rd ⊕ #IMM → Rd
Performs a logical exclusive OR operation on a general register and another
general register or immediate data.
NOT
B/W/L
¬ Rd → Rd
Takes the one's complement (logical complement) of general register
contents.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
Rev. 3.00 Sep 14, 2005 page 35 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.6
Shift Instructions
Instruction Size*
Function
SHAL,
SHAR
B/W/L
Rd (shift) → Rd
SHLL,
SHLR
B/W/L
Rd (shift) → Rd
ROTL,
ROTR
B/W/L
Rd (rotate) → Rd
ROTXL,
ROTXR
B/W/L
Performs an arithmetic shift on general register contents.
Performs a logical shift on general register contents.
Rotates general register contents.
Rd (rotate) → Rd
Rotates general register contents, including the carry bit.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
Rev. 3.00 Sep 14, 2005 page 36 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.7
Bit Manipulation Instructions
Instruction Size*
Function
BSET
1 → (<bit-No.> of <EAd>)
B
Sets a specified bit in a general register or memory operand to 1. The bit
number is specified by 3-bit immediate data or the lower 3 bits of a general
register.
BCLR
B
0 → (<bit-No.> of <EAd>)
Clears a specified bit in a general register or memory operand to 0. The bit
number is specified by 3-bit immediate data or the lower 3 bits of a general
register.
BNOT
B
¬ (<bit-No.> of <EAd>) → (<bit-No.> of <EAd>)
Inverts a specified bit in a general register or memory operand. The bit
number is specified by 3-bit immediate data or the lower 3 bits of a general
register.
BTST
B
¬ (<bit-No.> of <EAd>) → Z
Tests a specified bit in a general register or memory operand and sets or
clears the Z flag accordingly. The bit number is specified by 3-bit immediate
data or the lower 3 bits of a general register.
BAND
B
C ∧ (<bit-No.> of <EAd>) → C
ANDs the carry flag with a specified bit in a general register or memory
operand and stores the result in the carry flag.
BIAND
B
C ∧ [¬ (<bit-No.> of <EAd>)] → C
ANDs the carry flag with the inverse of a specified bit in a general register or
memory operand and stores the result in the carry flag.
The bit number is specified by 3-bit immediate data.
BOR
B
C ∨ (<bit-No.> of <EAd>) → C
ORs the carry flag with a specified bit in a general register or memory
operand and stores the result in the carry flag.
BIOR
B
C ∨ [¬ (<bit-No.> of <EAd>)] → C
ORs the carry flag with the inverse of a specified bit in a general register or
memory operand and stores the result in the carry flag.
The bit number is specified by 3-bit immediate data.
BXOR
B
C ⊕ (<bit-No.> of <EAd>) → C
Exclusive-ORs the carry flag with a specified bit in a general register or
memory operand and stores the result in the carry flag.
Rev. 3.00 Sep 14, 2005 page 37 of 910
REJ09B0258-0300
Section 2 CPU
Instruction Size*
Function
BIXOR
C ⊕ [¬ (<bit-No.> of <EAd>)] → C
B
Exclusive-ORs the carry flag with the inverse of a specified bit in a general
register or memory operand and stores the result in the carry flag.
The bit number is specified by 3-bit immediate data.
BLD
B
(<bit-No.> of <EAd>) → C
Transfers a specified bit in a general register or memory operand to the carry
flag.
BILD
B
¬ (<bit-No.> of <EAd>) → C
Transfers the inverse of a specified bit in a general register or memory
operand to the carry flag.
The bit number is specified by 3-bit immediate data.
BST
B
C → (<bit-No.> of <EAd>)
Transfers the carry flag value to a specified bit in a general register or
memory operand.
BIST
B
C → ¬ (<bit-No.> of <EAd>)
Transfers the inverse of the carry flag value to a specified bit in a general
register or memory operand.
The bit number is specified by 3-bit immediate data.
Note: * Size refers to the operand size.
B: Byte
Rev. 3.00 Sep 14, 2005 page 38 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.8
Branching Instructions
Instruction Size
Function
Bcc
Branches to a specified address if address specified condition is met. The
branching conditions are listed below.
—
Mnemonic
Description
Condition
BRA (BT)
Always (true)
Always
BRN (BF)
Never (false)
Never
BHI
High
C∨Z=0
BLS
Low or same
C∨Z=1
Bcc (BHS)
Carry clear (high or same) C = 0
BCS (BLO)
Carry set (low)
C=1
BNE
Not equal
Z=0
BEQ
Equal
Z=1
BVC
Overflow clear
V=0
BVS
Overflow set
V=1
BPL
Plus
N=0
BMI
Minus
N=1
BGE
Greater or equal
N⊕V=0
BLT
Less than
N⊕V=1
BGT
Greater than
Z ∨ (N ⊕ V) = 0
BLE
Less or equal
Z ∨ (N ⊕ V) = 1
JMP
—
Branches unconditionally to a specified address
BSR
—
Branches to a subroutine at a specified address
JSR
—
Branches to a subroutine at a specified address
RTS
—
Returns from a subroutine
Rev. 3.00 Sep 14, 2005 page 39 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.9
System Control Instructions
Instruction Size*
Function
TRAPA
—
Starts trap-instruction exception handling
RTE
—
Returns from an exception-handling routine
SLEEP
—
Causes a transition to the power-down state
LDC
B/W
(EAs) → CCR
Moves the source operand contents to the condition code register. The
condition code register size is one byte, but in transfer from memory, data is
read by word access.
STC
B/W
CCR → (EAd)
Transfers the CCR contents to a destination location. The condition code
register size is one byte, but in transfer to memory, data is written by word
access.
ANDC
B
CCR ∧ #IMM → CCR
ORC
B
CCR ∨ #IMM → CCR
Logically ANDs the condition code register with immediate data.
Logically ORs the condition code register with immediate data.
XORC
B
CCR ⊕ #IMM → CCR
Logically exclusive-ORs the condition code register with immediate data.
NOP
—
PC + 2 → PC
Only increments the program counter.
Note: * Size refers to the operand size.
B: Byte
W: Word
Rev. 3.00 Sep 14, 2005 page 40 of 910
REJ09B0258-0300
Section 2 CPU
Table 2.10 Block Transfer Instruction
Instruction
Size
Function
EEPMOV.B
—
if R4L ≠ 0 then
repeat @ER5+ → @ER6+, R4L – 1 → R4L
until
R4L = 0
else next;
EEPMOV.W
—
if R4 ≠ 0 then
repeat @ER5+ → @ER6+, R4 – 1 → R4
until
R4 = 0
else next;
Block transfer instruction. This instruction transfers the number of data bytes
specified by R4L or R4, starting from the address indicated by ER5, to the
location starting at the address indicated by ER6. At the end of the transfer,
the next instruction is executed.
2.6.4
Basic Instruction Formats
The H8/300H instructions consist of 2-byte (1-word) units. An instruction consists of an
operation field (OP field), a register field (r field), an effective address extension (EA field), and a
condition field (cc).
Operation Field: Indicates the function of the instruction, the addressing mode, and the
operation to be carried out on the operand. The operation field always includes the first 4 bits of
the instruction. Some instructions have two operation fields.
Register Field: Specifies a general register. Address registers are specified by 3 bits, data
registers by 3 bits or 4 bits. Some instructions have two register fields. Some have no register
field.
Effective Address Extension: Eight, 16, or 32 bits specifying immediate data, an absolute
address, or a displacement. A 24-bit address or displacement is treated as 32-bit data in which the
first 8 bits are 0 (H'00).
Condition Field: Specifies the branching condition of Bcc instructions.
Figure 2.9 shows examples of instruction formats.
Rev. 3.00 Sep 14, 2005 page 41 of 910
REJ09B0258-0300
Section 2 CPU
Operation field only
op
NOP, RTS, etc.
Operation field and register fields
op
rn
rm
ADD.B Rn, Rm, etc.
Operation field, register fields, and effective address extension
op
rn
rm
MOV.B @(d:16, Rn), Rm
EA (disp)
Operation field, effective address extension, and condition field
op
cc
EA (disp)
BRA d:8
Figure 2.9 Instruction Formats
2.6.5
Notes on Use of Bit Manipulation Instructions
The BSET, BCLR, BNOT, BST, and BIST instructions read a byte of data, modify a bit in the
byte, then write the byte back. Care is required when these instructions are used to access
registers with write-only bits, or to access ports.
Step
1
Description
Read
Read one data byte at the specified address
2
Modify
Modify one bit in the data byte
3
Write
Write the modified data byte back to the specified address
Example 1: BCLR is executed to clear bit 0 in the port 4 data direction register (P4DDR) under
the following conditions.
P47, P46: Input pins
P45 – P40: Output pins
The intended purpose of this BCLR instruction is to switch P40 from output to input.
Rev. 3.00 Sep 14, 2005 page 42 of 910
REJ09B0258-0300
Section 2 CPU
Before Execution of BCLR Instruction
P47
P46
P45
P44
P43
P42
P41
P40
Input/output
Input
Input
Output
Output
Output
Output
Output
Output
DDR
0
0
1
1
1
1
1
1
P42
P41
P40
Execution of BCLR Instruction
BCLR #0, @P4DDR ;Clear bit 0 in data direction register
After Execution of BCLR Instruction
P47
P46
P45
P44
P43
Input/output
Output
Output
Output
Output
Output
Output
Output
Input
DDR
1
1
1
1
1
1
1
0
Explanation: To execute the BCLR instruction, the CPU begins by reading P4DDR. Since
P4DDR is a write-only register, it is read as H'FF, even though its true value is H'3F.
Next the CPU clears bit 0 of the read data, changing the value to H'FE.
Finally, the CPU writes this value (H'FE) back to P4DDR to complete the BCLR instruction.
As a result, P40DDR is cleared to 0, making P40 an input pin. In addition, P47DDR and P46DDR
are set to 1, making P47 and P46 output pins.
The BCLR instruction can be used to clear flags in the on-chip registers to 0. In an interrupthandling routine, for example, if it is known that the flag is set to 1, it is not necessary to read the
flag ahead of time.
Rev. 3.00 Sep 14, 2005 page 43 of 910
REJ09B0258-0300
Section 2 CPU
2.7
Addressing Modes and Effective Address Calculation
2.7.1
Addressing Modes
The H8/300H CPU supports the eight addressing modes listed in table 2.11. Each instruction uses
a subset of these addressing modes. Arithmetic and logic instructions can use the register direct
and immediate modes. Data transfer instructions can use all addressing modes except programcounter relative and memory indirect. Bit manipulation instructions use register direct, register
indirect, or absolute (@aa:8) addressing mode to specify an operand, and register direct (BSET,
BCLR, BNOT, and BTST instructions) or immediate (3-bit) addressing mode to specify a bit
number in the operand.
Table 2.11 Addressing Modes
No.
Addressing Mode
Symbol
1
Register direct
Rn
2
Register indirect
@ERn
3
Register indirect with displacement
@(d:16, ERn)/@(d:24, ERn)
4
Register indirect with post-increment
Register indirect with pre-decrement
@ERn+
@–ERn
5
Absolute address
@aa:8/@aa:16/@aa:24
6
Immediate
#xx:8/#xx:16/#xx:32
7
Program-counter relative
@(d:8, PC)/@(d:16, PC)
8
Memory indirect
@@aa:8
1 Register Direct—Rn: The register field of the instruction code specifies an 8-, 16-, or 32-bit
register containing the operand. R0H to R7H and R0L to R7L can be specified as 8-bit registers.
R0 to R7 and E0 to E7 can be specified as 16-bit registers. ER0 to ER7 can be specified as 32-bit
registers.
2 Register Indirect—@ERn: The register field of the instruction code specifies an address
register (ERn), the lower 24 bits of which contain the address of the operand.
3 Register Indirect with Displacement—@(d:16, ERn) or @(d:24, ERn): A 16-bit or 24-bit
displacement contained in the instruction code is added to the contents of an address register
(ERn) specified by the register field of the instruction, and the lower 24 bits of the sum specify
the address of a memory operand. A 16-bit displacement is sign-extended when added.
Rev. 3.00 Sep 14, 2005 page 44 of 910
REJ09B0258-0300
Section 2 CPU
4 Register Indirect with Post-Increment or Pre-Decrement—@ERn+ or @–ERn:
• Register indirect with post-increment—@ERn+
The register field of the instruction code specifies an address register (ERn) the lower 24 bits
of which contain the address of a memory operand. After the operand is accessed, 1, 2, or 4 is
added to the address register contents (32 bits) and the sum is stored in the address register.
The value added is 1 for byte access, 2 for word access, or 4 for longword access. For word or
longword access, the register value should be even.
• Register indirect with pre-decrement—@–ERn
The value 1, 2, or 4 is subtracted from an address register (ERn) specified by the register field
in the instruction code, and the lower 24 bits of the result become the address of a memory
operand. The result is also stored in the address register. The value subtracted is 1 for byte
access, 2 for word access, or 4 for longword access. For word or longword access, the
resulting register value should be even.
5 Absolute Address—@aa:8, @aa:16, or @aa:24: The instruction code contains the absolute
address of a memory operand. The absolute address may be 8 bits long (@aa:8), 16 bits long
(@aa:16), or 24 bits long (@aa:24). For an 8-bit absolute address, the upper 16 bits are all
assumed to be 1 (H'FFFF). For a 16-bit absolute address the upper 8 bits are a sign extension. A
24-bit absolute address can access the entire address space. Table 2.12 indicates the accessible
address ranges.
Table 2.12 Absolute Address Access Ranges
Absolute
Address
1-Mbyte Modes
16-Mbyte Modes
8 bits (@aa:8)
H'FFF00 to H'FFFFF
(1048320 to 1048575)
H'FFFF00 to H'FFFFFF
(16776960 to 16777215)
16 bits (@aa:16)
H'00000 to H'07FFF,
H'F8000 to H'FFFFF
(0 to 32767, 1015808 to 1048575)
H'000000 to H'007FFF,
H'FF8000 to H'FFFFFF
(0 to 32767, 16744448 to 16777215)
24 bits (@aa:24)
H'00000 to H'FFFFF
(0 to 1048575)
H'000000 to H'FFFFFF
(0 to 16777215)
6 Immediate—#xx:8, #xx:16, or #xx:32: The instruction code contains 8-bit (#xx:8), 16-bit
(#xx:16), or 32-bit (#xx:32) immediate data as an operand.
The instruction codes of the ADDS, SUBS, INC, and DEC instructions contain immediate data
implicitly. The instruction codes of some bit manipulation instructions contain 3-bit immediate
data specifying a bit number. The TRAPA instruction code contains 2-bit immediate data
specifying a vector address.
Rev. 3.00 Sep 14, 2005 page 45 of 910
REJ09B0258-0300
Section 2 CPU
7 Program-Counter Relative—@(d:8, PC) or @(d:16, PC): This mode is used in the Bcc and
BSR instructions. An 8-bit or 16-bit displacement contained in the instruction code is signextended to 24 bits and added to the 24-bit PC contents to generate a 24-bit branch address. The
PC value to which the displacement is added is the address of the first byte of the next instruction,
so the possible branching range is –126 to +128 bytes (–63 to +64 words) or –32766 to
+32768 bytes (–16383 to +16384 words) from the branch instruction. The resulting value should
be an even number.
8 Memory Indirect—@@aa:8: This mode can be used by the JMP and JSR instructions. The
instruction code contains an 8-bit absolute address specifying a memory operand. This memory
operand contains a branch address. The memory operand is accessed by longword access. The
first byte of the memory operand is ignored, generating a 24-bit branch address. See figure 2.10.
The upper bits of the 8-bit absolute address are assumed to be 0 (H'0000), so the address range is
0 to 255 (H'000000 to H'0000FF). Note that the first part of this range is also the exception vector
area. For further details see section 5, Interrupt Controller.
Specified by @aa:8
Reserved
Branch address
Figure 2.10 Memory-Indirect Branch Address Specification
When a word-size or longword-size memory operand is specified, or when a branch address is
specified, if the specified memory address is odd, the least significant bit is regarded as 0. The
accessed data or instruction code therefore begins at the preceding address. See section 2.5.2,
Memory Data Formats.
2.7.2
Effective Address Calculation
Table 2.13 explains how an effective address is calculated in each addressing mode. In the
1-Mbyte operating modes the upper 4 bits of the calculated address are ignored in order to
generate a 20-bit effective address.
Rev. 3.00 Sep 14, 2005 page 46 of 910
REJ09B0258-0300
4
3
2
r
r
r
op
r
Register indirect with pre-decrement
@–ERn
op
Register indirect with post-increment
@ERn+
Register indirect with post-increment
or pre-decrement
op
Register indirect with displacement
@(d:16, ERn)/@(d:24, ERn)
op
Register indirect (@ERn)
rm rn
Register direct (Rn)
1
op
Addressing Mode and
Instruction Format
No.
31
31
1 for a byte operand,
2 for a word operand,
4 for a longword operand
1, 2, or 4
General register contents
1, 2, or 4
General register contents
disp
General register contents
General register contents
Sign extension
31
31
Effective Address Calculation
Table 2.13 Effective Address Calculation
0
0
0
0
23
23
23
23
Operand is general
register contents
Effective Address
0
0
0
0
Section 2 CPU
Rev. 3.00 Sep 14, 2005 page 47 of 910
REJ09B0258-0300
Rev. 3.00 Sep 14, 2005 page 48 of 910
REJ09B0258-0300
7
6
5
No.
abs
abs
abs
IMM
op
disp
Program-counter relative
@(d:8, PC) or @(d:16, PC)
op
Immediate
#xx:8, #xx:16, or #xx:32
op
@aa:24
op
@aa:16
op
Absolute address
@aa:8
Addressing Mode and
Instruction Format
disp
PC contents
Sign
extension
23
Effective Address Calculation
0
16 15
H'FFFF
8 7
23
Operand is immediate data
23
Sign
extension
23
23
Effective Address
0
0
0
0
Section 2 CPU
Memory indirect @@aa:8
8
abs
Legend
r, rm, rn:
op:
disp:
IMM:
abs:
abs
Register field
Operation field
Displacement
Immediate data
Absolute address
op
Advanced mode
op
Normal mode
Addressing Mode and
Instruction Format
No.
31
8 7
abs
0
H'0000
8 7
abs
0
0
15
0
Memory contents
H'0000
Memory contents
23
23
Effective Address Calculation
23
23 16 15
H'00
Effective Address
0
0
Section 2 CPU
Rev. 3.00 Sep 14, 2005 page 49 of 910
REJ09B0258-0300
Section 2 CPU
2.8
Processing States
2.8.1
Overview
The H8/300H CPU has five processing states: the program execution state, exception-handling
state, power-down state, reset state, and bus-released state. The power-down state includes sleep
mode, software standby mode, and hardware standby mode. Figure 2.11 classifies the processing
states. Figure 2.13 indicates the state transitions.
Processing states
Program execution state
The CPU executes program instructions in sequence
Exception-handling state
A transient state in which the CPU executes a hardware sequence
(saving PC and CCR, fetching a vector, etc.) in response to a reset,
interrupt, or other exception
Bus-released state
The external bus has been released in response to a bus request
signal from a bus master other than the CPU
Reset state
The CPU and all on-chip supporting modules are initialized and halted
Power-down state
Sleep mode
The CPU is halted to conserve power
Software standby mode
Hardware standby mode
Figure 2.11 Processing States
Rev. 3.00 Sep 14, 2005 page 50 of 910
REJ09B0258-0300
Section 2 CPU
2.8.2
Program Execution State
In this state the CPU executes program instructions in normal sequence.
2.8.3
Exception-Handling State
The exception-handling state is a transient state that occurs when the CPU alters the normal
program flow due to a reset, interrupt, or trap instruction. The CPU fetches a starting address
from the exception vector table and branches to that address. In interrupt and trap exception
handling the CPU references the stack pointer (ER7) and saves the program counter and
condition code register.
Types of Exception Handling and Their Priority: Exception handling is performed for resets,
interrupts, and trap instructions. Table 2.14 indicates the types of exception handling and their
priority. Trap instruction exceptions are accepted at all times in the program execution state.
Table 2.14 Exception Handling Types and Priority
Priority
Type of Exception Detection Timing
Start of Exception Handling
High
Reset
Synchronized with clock
Exception handling starts immediately
when RES changes from low to high
Interrupt
End of instruction
execution or end of
exception handling*
When an interrupt is requested,
exception handling starts at the end of
the current instruction or current
exception-handling sequence
Trap instruction
When TRAPA instruction Exception handling starts when a trap
is executed
(TRAPA) instruction is executed
Low
Note: * Interrupts are not detected at the end of the ANDC, ORC, XORC, and LDC instructions,
or immediately after reset exception handling.
Figure 2.12 classifies the exception sources. For further details about exception sources, vector
numbers, and vector addresses, see section 4, Exception Handling, and section 5, Interrupt
Controller.
Rev. 3.00 Sep 14, 2005 page 51 of 910
REJ09B0258-0300
Section 2 CPU
Reset
External interrupts
Exception
sources
Interrupt
Internal interrupts (from on-chip supporting modules)
Trap instruction
Figure 2.12 Classification of Exception Sources
Bus request
End of bus release
Program execution state
End of bus
release
Bus
request
Exception
handling source
Bus-released state
End of
exception
handling
Interrupt source
Exception-handling state
NMI, IRQ 0 , IRQ 1,
or IRQ 2 interrupt
SLEEP
instruction
with SSBY = 0
Sleep mode
SLEEP instruction
with SSBY = 1
Software standby mode
RES = "High"
Reset state
*1
STBY="High", RES ="Low"
Hardware standby mode
*2
Power-down state
Notes: 1. From any state except hardware standby mode, a transition to the reset state occurs
whenever RES goes low.
2. From any state, a transition to hardware standby mode occurs when STBY goes low.
Figure 2.13 State Transitions
Rev. 3.00 Sep 14, 2005 page 52 of 910
REJ09B0258-0300
Section 2 CPU
2.8.4
Exception-Handling Sequences
Reset Exception Handling: Reset exception handling has the highest priority. The reset state is
entered when the RES signal goes low. Reset exception handling starts after that, when RES
changes from low to high. When reset exception handling starts the CPU fetches a start address
from the exception vector table and starts program execution from that address. All interrupts,
including NMI, are disabled during the reset exception-handling sequence and immediately after
it ends.
Interrupt Exception Handling and Trap Instruction Exception Handling: When these
exception-handling sequences begin, the CPU references the stack pointer (ER7) and pushes the
program counter and condition code register on the stack. Next, if the UE bit in the system
control register (SYSCR) is set to 1, the CPU sets the I bit in the condition code register to 1. If
the UE bit is cleared to 0, the CPU sets both the I bit and the UI bit in the condition code register
to 1. Then the CPU fetches a start address from the exception vector table and execution
branches to that address.
Figure 2.14 shows the stack after the exception-handling sequence.
Rev. 3.00 Sep 14, 2005 page 53 of 910
REJ09B0258-0300
Section 2 CPU
SP–4
SP (ER7)
SP–3
SP+1
SP–2
SP+2
SP–1
SP+3
Stack area
SP (ER7)
Before exception
handling starts
CCR
PC
SP+4
Pushed on stack
Even
address
After exception
handling ends
Legend
CCR: Condition code register
SP:
Stack pointer
Notes: 1. PC is the address of the first instruction executed after the return from the
exception-handling routine.
2. Registers must be saved and restored by word access or longword access,
starting at an even address.
Figure 2.14 Stack Structure after Exception Handling
2.8.5
Bus-Released State
In this state the bus is released to a bus master other than the CPU, in response to a bus request.
The bus masters other than the CPU are the DMA controller, the DRAM interface, and an
external bus master. While the bus is released, the CPU halts except for internal operations.
Interrupt requests are not accepted. For details see section 6.10, Bus Arbiter.
2.8.6
Reset State
When the RES input goes low all current processing stops and the CPU enters the reset state. The
I bit in the condition code register is set to 1 by a reset. All interrupts are masked in the reset
state. Reset exception handling starts when the RES signal changes from low to high.
The reset state can also be entered by a watchdog timer overflow. For details see section 12,
Watchdog Timer.
Rev. 3.00 Sep 14, 2005 page 54 of 910
REJ09B0258-0300
Section 2 CPU
2.8.7
Power-Down State
In the power-down state the CPU stops operating to conserve power. There are three modes:
sleep mode, software standby mode, and hardware standby mode.
Sleep Mode: A transition to sleep mode is made if the SLEEP instruction is executed while the
SSBY bit is cleared to 0 in the system control register (SYSCR). CPU operations stop
immediately after execution of the SLEEP instruction, but the contents of CPU registers are
retained.
Software Standby Mode: A transition to software standby mode is made if the SLEEP
instruction is executed while the SSBY bit is set to 1 in SYSCR. The CPU and clock halt and all
on-chip supporting modules stop operating. The on-chip supporting modules are reset, but as long
as a specified voltage is supplied the contents of CPU registers and on-chip RAM are retained.
The I/O ports also remain in their existing states.
Hardware Standby Mode: A transition to hardware standby mode is made when the STBY
input goes low. As in software standby mode, the CPU and all clocks halt and the on-chip
supporting modules are reset, but as long as a specified voltage is supplied, on-chip RAM
contents are retained.
For further information see section 20, Power-Down State.
Rev. 3.00 Sep 14, 2005 page 55 of 910
REJ09B0258-0300
Section 2 CPU
2.9
Basic Operational Timing
2.9.1
Overview
The H8/300H CPU operates according to the system clock (ø). The interval from one rise of the
system clock to the next rise is referred to as a “state.” A memory cycle or bus cycle consists of
two or three states. The CPU uses different methods to access on-chip memory, the on-chip
supporting modules, and the external address space. Access to the external address space can be
controlled by the bus controller.
2.9.2
On-Chip Memory Access Timing
On-chip memory is accessed in two states. The data bus is 16 bits wide, permitting both byte and
word access. Figure 2.15 shows the on-chip memory access cycle. Figure 2.16 indicates the pin
states.
Bus cycle
T1 state
T2 state
φ
Internal address bus
Address
Internal read signal
Internal data bus
(read access)
Read data
Internal write signal
Internal data bus
(write access)
Write data
Figure 2.15 On-Chip Memory Access Cycle
Rev. 3.00 Sep 14, 2005 page 56 of 910
REJ09B0258-0300
Section 2 CPU
T1
T2
φ
Address bus
AS , RD, HWR , LWR
Address
High
High impedance
D15 to D0
Figure 2.16 Pin States during On-Chip Memory Access
2.9.3
On-Chip Supporting Module Access Timing
The on-chip supporting modules are accessed in three states. The data bus is 8 or 16 bits wide,
depending on the internal I/O register being accessed. Figure 2.17 shows the on-chip supporting
module access timing. Figure 2.18 indicates the pin states.
Bus cycle
T1 state
T2 state
T3 state
φ
Address bus
Read
access
Address
Internal read signal
Internal data bus
Read data
Internal write signal
Write
access
Internal data bus
Write data
Figure 2.17 Access Cycle for On-Chip Supporting Modules
Rev. 3.00 Sep 14, 2005 page 57 of 910
REJ09B0258-0300
Section 2 CPU
T1
T2
T3
φ
Address bus
AS , RD, HWR , LWR
Address
High
High impedance
D15 to D0
Figure 2.18 Pin States during Access to On-Chip Supporting Modules
2.9.4
Access to External Address Space
The external address space is divided into eight areas (areas 0 to 7). Bus-controller settings
determine whether each area is accessed via an 8-bit or 16-bit bus, and whether it is accessed in
two or three states. For details see section 6, Bus Controller.
Rev. 3.00 Sep 14, 2005 page 58 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
Section 3 MCU Operating Modes
3.1
Overview
3.1.1
Operating Mode Selection
The H8/3068F has seven operating modes (modes 1 to 7) that are selected by the mode pins (MD2
to MD0) as indicated in table 3.1. The input at these pins determines the size of the address space
and the initial bus mode.
Table 3.1
Operating Mode Selection
Description
Mode Pins
Operating
Mode
MD2 MD1 MD0
Address Space
Initial Bus On-Chip
Mode*1
ROM
On-Chip
RAM
—
0
0
0
—
—
—
—
Mode 1
0
0
1
Expanded mode
8 bits
Disabled
Enabled*2
Mode 2
0
1
0
Expanded mode
16 bits
Disabled
Enabled*2
Mode 3
0
1
1
Expanded mode
8 bits
Disabled
Enabled*2
Mode 4
1
0
0
Expanded mode
16 bits
Disabled
Enabled*2
Mode 5
1
0
1
Expanded mode
8 bits
Enabled
Enabled*2
Mode 6
1
1
0
Single-chip normal mode
—
Enabled
Enabled
Mode 7
1
1
1
Single-chip advanced
mode
—
Enabled
Enabled
Notes: 1. In modes 1 to 5, an 8-bit or 16-bit data bus can be selected on a per-area basis by
settings made in the area bus width control register (ABWCR). For details see
section 6, Bus Controller.
2. If the RAME bit in SYSCR is cleared to 0, these addresses become external
addresses.
For the address space size there are three choices: 64 kbytes, 1 Mbyte, or 16 Mbyte.The external
data bus is either 8 or 16 bits wide depending on ABWCR settings. If 8-bit access is selected for
all areas, 8-bit bus mode is used. For details see section 6, Bus Controller.
Modes 1 to 4 are externally expanded modes that enable access to external memory and
peripheral devices and disable access to the on-chip ROM. Modes 1 and 2 support a maximum
address space of 1 Mbyte. Modes 3 and 4 support a maximum address space of 16 Mbytes.
Rev. 3.00 Sep 14, 2005 page 59 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
Mode 5 is an externally expanded mode that enables access to external memory and peripheral
devices and also enables access to the on-chip ROM. Mode 5 supports a maximum address space
of 16 Mbytes.
Modes 6 and 7 are single-chip modes that operate using the on-chip ROM, RAM, and registers,
and makes all I/O ports available. Mode 6 supports a maximum address space of 64 kbytes. Mode
7 supports a maximum address space of 1 Mbyte.
The H8/3068F can be used only in modes 1 to 7. The inputs at the mode pins must select one of
these seven modes. The inputs at the mode pins must not be changed during operation.
3.1.2
Register Configuration
The H8/3068F has a mode control register (MDCR) that indicates the inputs at the mode pins
(MD2 to MD0), and a system control register (SYSCR). Table 3.2 summarizes these registers.
Table 3.2
Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'EE011
Mode control register
MDCR
R
Undetermined
H'EE012
System control register
SYSCR
R/W
H'09
Note: * Lower 20 bits of the address in advanced mode.
Rev. 3.00 Sep 14, 2005 page 60 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
3.2
Mode Control Register (MDCR)
MDCR is an 8-bit read-only register that indicates the current operating mode of the
H8/3068F.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
MDS2
MDS1
MDS0
Initial value
1
1
0
0
0
—*
—*
—*
Read/Write
—
—
—
—
—
R
R
R
Reserved bits
Reserved bits
Mode select 2 to 0
Bits indicating the current
operating mode
Note: * Determined by pins MD2 to MD0.
Bits 7 and 6—Reserved: These bits can not be modified and are always read as 1.
Bits 5 to 3—Reserved: These bits can not be modified and are always read as 0.
Bits 2 to 0—Mode Select 2 to 0 (MDS2 to MDS0): These bits indicate the logic levels at pins
MD2 to MD0 (the current operating mode). MDS2 to MDS0 correspond to MD2 to MD0. MDS2 to
MDS0 are read-only bits. The mode pin (MD2 to MD0) levels are latched into these bits when
MDCR is read.
Rev. 3.00 Sep 14, 2005 page 61 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
3.3
System Control Register (SYSCR)
SYSCR is an 8-bit register that controls the operation of the H8/3068F.
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
Initial value
0
0
0
0
1
0
0
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RAM enable
Enables or
disables
on-chip RAM
Software standby output
port enable
Selects the output state
of the address bus
and bus control signals
in software standby mode
NMI edge select
Selects the valid edge
of the NMI input
User bit enable
Selects whether to use the UI bit in CCR
as a user bit or an interrupt mask bit
Standby timer select 2 to 0
These bits select the waiting time at
recovery from software standby mode
Software standby
Enables transition to software standby mode
Bit 7—Software Standby (SSBY): Enables transition to software standby mode. (For further
information about software standby mode see section 20, Power-Down State.)
When software standby mode is exited by an external interrupt, this bit remains set to 1. To clear
this bit, write 0.
Bit 7
SSBY
Description
0
SLEEP instruction causes transition to sleep mode
1
SLEEP instruction causes transition to software standby mode
Rev. 3.00 Sep 14, 2005 page 62 of 910
REJ09B0258-0300
(Initial value)
Section 3 MCU Operating Modes
Bits 6 to 4—Standby Timer Select 2 to 0 (STS2 to STS0): These bits select the length of time
the CPU and on-chip supporting modules wait for the internal clock oscillator to settle when
software standby mode is exited by an external interrupt.
When using a crystal oscillator, set these bits so that the waiting time will be at least 7 ms at the
system clock rate.
For further information about waiting time selection, see section 20.4.3, Selection of Waiting
Time for Exit from Software Standby Mode.
Bit 6
STS2
Bit 5
STS1
Bit 4
STS0
Description
0
0
0
Waiting time = 8,192 states
0
0
1
Waiting time = 16,384 states
0
1
0
Waiting time = 32,768 states
0
1
1
Waiting time = 65,536 states
1
0
0
Waiting time = 131,072 states
1
0
1
Waiting time = 262,144 states
1
1
0
Waiting time = 1,024 states
1
1
1
Illegal setting
(Initial value)
Bit 3—User Bit Enable (UE): Selects whether to use the UI bit in the condition code register as
a user bit or an interrupt mask bit.
Bit 3
UE
Description
0
UI bit in CCR is used as an interrupt mask bit
1
UI bit in CCR is used as a user bit
(Initial value)
Bit 2—NMI Edge Select (NMIEG): Selects the valid edge of the NMI input.
Bit 2
NMIEG
Description
0
An interrupt is requested at the falling edge of NMI
1
An interrupt is requested at the rising edge of NMI
(Initial value)
Rev. 3.00 Sep 14, 2005 page 63 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
Bit 1—Software Standby Output Port Enable (SSOE): Specifies whether the address bus and
bus control signals (CS0 to CS7, AS, RD, HWR, LWR, UCAS, LCAS, and RFSH) are kept as
outputs or fixed high, or placed in the high-impedance state in software standby mode.
Bit 1
SSOE
Description
0
In software standby mode, the address bus and bus control signals are all highimpedance
(Initial value)
1
In software standby mode, the address bus retains its output state and bus control
signals are fixed high
Bit 0—RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is
initialized by the rising edge of the RES signal. It is not initialized in software standby mode.
Bit 0
RAME
Description
0
On-chip RAM is disabled
1
On-chip RAM is enabled
3.4
Operating Mode Descriptions
3.4.1
Mode 1
(Initial value)
Ports 1, 2, and 5 function as address pins A19 to A0, permitting access to a maximum 1-Mbyte
address space. The initial bus mode after a reset is 8 bits, with 8-bit access to all areas. If at least
one area is designated for 16-bit access in ABWCR, the bus mode switches to 16 bits.
3.4.2
Mode 2
Ports 1, 2, and 5 function as address pins A19 to A0, permitting access to a maximum 1-Mbyte
address space. The initial bus mode after a reset is 16 bits, with 16-bit access to all areas. If all
areas are designated for 8-bit access in ABWCR, the bus mode switches to 8 bits.
3.4.3
Mode 3
Ports 1, 2, and 5 and part of port A function as address pins A23 to A0, permitting access to a
maximum 16-Mbyte address space. The initial bus mode after a reset is 8 bits, with 8-bit access to
all areas. If at least one area is designated for 16-bit access in ABWCR, the bus mode switches to
Rev. 3.00 Sep 14, 2005 page 64 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
16 bits. A23 to A21 are valid when 0 is written in bits 7 to 5 of the bus release control register
(BRCR). (In this mode A20 is always used for address output.)
3.4.4
Mode 4
Ports 1, 2, and 5 and part of port A function as address pins A23 to A0, permitting access to a
maximum 16-Mbyte address space. The initial bus mode after a reset is 16 bits, with 16-bit access
to all areas. If all areas are designated for 8-bit access in ABWCR, the bus mode switches to
8 bits. A23 to A21 are valid when 0 is written in bits 7 to 5 of BRCR. (In this mode A20 is always
used for address output.)
3.4.5
Mode 5
Ports 1, 2, and 5 and part of port A can function as address pins A23 to A0, permitting access to a
maximum 16-Mbyte address space, but following a reset they are input ports. To use ports 1, 2,
and 5 as an address bus, the corresponding bits in their data direction registers (P1DDR, P2DDR,
and P5DDR) must be set to 1. For A23 to A20 output, write 0 in bits 7 to 4 of BRCR. The initial
bus mode after a reset is 8 bits, with 8-bit access to all areas. If at least one area is designated for
16-bit access in ABWCR, the bus mode switches to 16 bits.
3.4.6
Mode 6
This mode operates using the on-chip ROM, RAM, and registers. All I/O ports are available.
Mode 6 supports a maximum address space of 64 kbytes.
3.4.7
Mode 7
This mode operates using the on-chip ROM, RAM, and registers. All I/O ports are available.
Mode 7 supports a 1-Mbyte address space.
Rev. 3.00 Sep 14, 2005 page 65 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
3.5
Pin Functions in Each Operating Mode
The pin functions of ports 1 to 5 and port A vary depending on the operating mode. Table 3.3
indicates their functions in each operating mode.
Table 3.3 Pin Functions in Each Mode
Port
Port 1
Mode 1
Mode 2
A7 to A0
Mode 3
A7 to A0
Mode 4
A7 to A0
Mode 5
A7 to A0
Mode 6
Mode 7
2
P17 to P10
P17 to P10
2
P17 to P10*
Port 2
A15 to A8
A15 to A8
A15 to A8
A15 to A8
P27 to P20*
P27 to P20
P27 to P20
Port 3
D15 to D8
D15 to D8
D15 to D8
D15 to D8
D15 to D8
P37 to P30
P37 to P30
1
P47 to P40
P47 to P40
2
P53 to P50
P53 to P50
PA7 to PA4
PA7 to PA4
1
1
1
1
Port 4
P47 to P40*
D7 to D0*
P47 to P40*
D7 to D0*
P47 to P40*
Port 5
A19 to A16
A19 to A16
A19 to A16
A19 to A16
P53 to P50*
Port A
PA7 to PA4
PA7 to PA4
PA6 to PA4,
A20*3
PA6 to PA4,
A20*3
4
PA7 to PA4*
Notes: 1. Initial state. The bus mode can be switched by settings in ABWCR. These pins function
as P47 to P40 in 8-bit bus mode, and as D7 to D0 in 16-bit bus mode.
2. Initial state. These pins become address output pins when the corresponding bits in
the data direction registers (P1DDR, P2DDR, P5DDR) are set to 1.
3. Initial state. A20 is always an address output pin. PA6 to PA4 are switched over to A23 to
A21 output by writing 0 in bits 7 to 5 of BRCR.
4. Initial state. PA7 to PA4 are switched over to A23 to A20 output by writing 0 in bits 7 to 4
of BRCR.
Rev. 3.00 Sep 14, 2005 page 66 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
3.6
Memory Map in Each Operating Mode
Figure 3.1 to 3.2 show a memory maps of the H8/3068F. The address space is divided into eight
areas.
The EMC bit in BCR can be read and written to select either of the two memory maps. For
details, see section 6.2.5, Bus Control Register (BCR).
The initial bus mode differs between modes 1 and 2, and also between modes 3 and 4.
The address locations of the on-chip RAM and on-chip registers differ between the 64-kbyte
mode (mode 6), the 1-Mbyte modes (modes 1, 2, and 7), and the 16-Mbyte modes (modes 3, 4,
and 5). The address range specifiable by the CPU in the 8- and 16-bit absolute addressing modes
(@aa:8 and @aa:16) also differs.
3.6.1
Note on Reserved Areas
The H8/3068F memory map includes reserved areas to which read/write access is prohibited.
Note that normal operation is not guaranteed if the following reserved areas are accessed.
The reserved area in the internal I/O register space.
The H8/3068F internal I/O register space includes a reserved area to which access is prohibited.
For details see Appendix B, Internal I/O Registers.
Rev. 3.00 Sep 14, 2005 page 67 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
H'EE0FF
H'F8000
H'FBF1F
H'FBF20
H'FFFE9
H'FFFEA
H'FFFFF
Area 1
Area 1
Area 2
H'3FFFFF
H'400000
Area 3
Area 2
Area 4
H'5FFFFF
H'600000
Area 5
Area 6
H'7FFFFF
H'800000
Area 7
Internal I/O
registers (2)
External
address
space
External
address
space
Area 3
Area 4
H'9FFFFF
H'A00000
External address
space
On-chip RAM*
16-bit absolute
addresses
H'1FFFFF
H'200000
Internal I/O
registers (1)
H'FFF00
H'FFF1F
H'FFF20
Area 0
Area 0
Area 5
16-bit absolute addresses
H'EE000
H'007FFF
H'BFFFFF
H'C00000
Area 6
H'DFFFFF
H'E00000
H'FEE000
Area 7
Internal I/O
registers (1)
H'FEE0FF
H'FF8000
H'FFBF1F
H'FFBF20
H'FFFF00
H'FFFF1F
H'FFFF20
H'FFFFE9
H'FFFFEA
H'FFFFFF
External address
space
On-chip RAM*
Internal I/O
registers (2)
External
address
space
16-bit absolute addresses
H'1FFFF
H'20000
H'3FFFF
H'40000
H'5FFFF
H'60000 External address
space
H'7FFFF
H'80000
H'9FFFF
H'A0000
H'BFFFF
H'C0000
H'DFFFF
H'E0000
H'0000FF
Memory-indirect
branch addresses
H'07FFF
Vector area
8-bit absolute addresses
H'000FF
Modes 3 and 4
(16-Mbyte expanded modes with
on-chip ROM disabled)
H'000000
16-bit absolute
addresses
Vector area
8-bit absolute addresses
H'00000
Memory-indirect
branch addresses
Modes 1 and 2
(1-Mbyte expanded modes with
on-chip ROM disabled)
Note: * External addresses can be accessed by disabling on-chip RAM.
Figure 3.1(1) H8/3068F Memory Map in Each Operating Mode
Rev. 3.00 Sep 14, 2005 page 68 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
H'DFFF
H'E000
Area 0
Area 3
H'E720
On-chip RAM
Area 5
H'FF00
Area 6
H'FF1F
H'FF20
Area 7
Internal I/O
registers (2)
H'FFFF
Internal I/O
registers (1)
H'EE0FF
H'F8000
H'FBF20
On-chip RAM
H'FFF00
16-bit absolute addresses
External
address
space
H'EE000
H'FFF1F
H'FFF20
H'FFFE9
H'FFFFF
Internal I/O
registers(2)
16-bit absolute addresses
Area 4
8-bit absolute addresses
H'FFFFE9
H'FFFFEA
Internal I/O
registers (2)
H'07FFF
H'5FFFF
External address
space
H'FFFF1F
H'FFFF20
On-chip ROM
H'E0FF
Area 2
H'FEE0FF
H'FFBF1F
H'FFBF20 On-chip RAM*
H'FFFF00
H'000FF
Internal I/O
registers (1)
Area 1
Internal I/O
registers (1)
H'FF8000
Vector area
16-bit absolute
addresses
On-chip ROM
H'FFE9
H'FEE000
H'FFFFFF
H'00FF
H'00000
Memory-indirect
branch addresses
H'007FFF
H'05FFFF
H'060000
H'1FFFFF
H'200000
H'3FFFFF
H'400000
H'5FFFFF
H'600000 External address
space
H'7FFFFF
H'800000
H'9FFFFF
H'A00000
H'BFFFFF
H'C00000
H'DFFFFF
H'E00000
Vector area
Mode 7
(single-chip advanced mode)
8-bit absolute addresses
On-chip ROM
H'0000
Memory-indirect
branch addresses
H'0000FF
Mode 6
(single-chip normal mode)
8-bit absolute addresses
Vector area
16-bit absolute
addresses
H'000000
Memory-indirect
branch addresses
Mode 5
(16-Mbyte expanded mode with
on-chip ROM enabled)
Note: * External addresses can be accessed by disabling on-chip RAM.
Figure 3.1(2) H8/3068F Memory Map in Each Operating Mode (EMC = 1)
Rev. 3.00 Sep 14, 2005 page 69 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
H'1FFFF
H'20000
H'3FFFF
H'40000
H'5FFFF
H'60000
H'7FFFF
H'80000
H'9FFFF
H'A0000
H'BFFFF
H'C0000
H'DFFFF
H'E0000
Area 0
Area 0
H'1FFFFF
H'200000
Area 1
Area 2
External address
space
Area 1
H'3FFFFF
H'400000
Area 3
External address
Area 2
space
Area 4
H'5FFFFF
H'600000
Area 5
Area 6
Area 3
Area 7
H'7FFFFF
H'800000
Area 4
Internal I/O
registers (1)
H'9FFFFF
H'A00000
External address
space
Area 5
H'F8000
H'FFF00
H'FFF80
H'FFFE0
H'FFFFF
On-chip RAM
(16 kbytes minus
96 bytes)
Internal I/O
registers (2)
External address
space
On-chip RAM
(96 bytes)
Internal I/O
registers (3)
16-bit absolute addresses
H'FFE80
H'BFFFFF
H'C00000
8-bit absolute
addresses
H'FBEE0
16-bit absolute
addresses
H'0000FF
H'007FFF
H'EE000
H'EE100
Vector area
Area 6
H'DFFFFF
H'E00000
Area 7
H'FEE000
H'FEE100
H'FF8000
Internal I/O
registers (1)
External address
space
H'FFBEE0
On-chip RAM
(16 kbytes minus
96 bytes)
H'FFFE80
H'FFFF00
H'FFFF80
H'FFFFE0
Internal I/O
registers (2)
External address
space
On-chip RAM
(96 bytes)
Internal I/O
registers (3)
16-bit absolute addresses
H'07FFF
H'000000
8-bit absolute addresses
H'000FF
16-bit absolute
addresses
Vector area
Memory-indirect
branch addresses
H'00000
Memory-indirect
branch addresses
Modes 3 and 4
(16-Mbyte expanded modes with
on-chip ROM disabled)
Modes 1 and 2
(1-Mbyte expanded modes with
on-chip ROM disabled)
H'FFFFFF
Figure 3.2(1) H8/3068F Memory Map in Each Operating Mode (EMC = 0)
Rev. 3.00 Sep 14, 2005 page 70 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
On-chip ROM
(384 kbytes)
H'007FFF
Vector area
H'000FF
On-chip ROM
H'07FFF
16-bit absolute
addresses
H'0000FF
H'00000
Memory-indirect
branch addresses
Vector area
Mode 7
(single-chip advanced mode)
16-bit absolute
addresses
H'000000
Memory-indirect
branch addresses
Mode 5
(16-Mbyte expanded mode with
on-chip ROM enabled)
H'05FFFF
H'060000
H'5FFFF
H'60000
Area 0
H'1FFFFF
H'200000
Area 1
H'3FFFFF
H'400000
External address Area 2
space
H'5FFFFF
H'600000
Area 3
H'7FFFFF
H'800000
H'EE000
Area 4
H'9FFFFF
H'A00000
H'EE100
Area 5
H'FBEE0
Area 6
H'DFFFFF
H'E00000
H'FFE80
Area 7
H'FF8000
H'FFF00
Internal I/O
registers (1)
H'FFF80
External address
space
H'FFFE0
H'FFBEE0
H'FFFF80
H'FFFFE0
Internal I/O
registers (2)
External address
space
On-chip RAM
(96 bytes)
Internal I/O
registers (3)
8-bit absolute addresses
H'FFFF00
On-chip RAM
(96 bytes)
Internal I/O
registers (3)
16-bit absolute addresses
H'FFFFF
On-chip RAM
(16 kbytes minus
96 bytes)
H'FFFE80
Internal I/O
registers (2)
8-bit absolute
addresses
H'FEE100
On-chip RAM
(16 kbytes minus
96 bytes)
16-bit absolute addresses
H'F8000
H'BFFFFF
H'C00000
H'FEE000
Internal I/O
registers (1)
H'FFFFFF
Figure 3.2(2) H8/3068F Memory Map in Each Operating Mode (EMC = 0)
Rev. 3.00 Sep 14, 2005 page 71 of 910
REJ09B0258-0300
Section 3 MCU Operating Modes
Rev. 3.00 Sep 14, 2005 page 72 of 910
REJ09B0258-0300
Section 4 Exception Handling
Section 4 Exception Handling
4.1
Overview
4.1.1
Exception Handling Types and Priority
As table 4.1 indicates, exception handling may be caused by a reset, trap instruction, or interrupt.
Exception handling is prioritized as shown in table 4.1. If two or more exceptions occur
simultaneously, they are accepted and processed in priority order. Trap instruction exceptions are
accepted at all times in the program execution state.
Table 4.1
Exception Types and Priority
Priority Exception Type
Start of Exception Handling
High
Reset
Starts immediately after a low-to-high transition at the RES pin
Interrupt
Interrupt requests are handled when execution of the current
instruction or handling of the current exception is completed
Low
4.1.2
Trap instruction (TRAPA) Started by execution of a trap instruction (TRAPA)
Exception Handling Operation
Exceptions originate from various sources. Trap instructions and interrupts are handled as
follows.
1. The program counter (PC) and condition code register (CCR) are pushed onto the stack.
2. The CCR interrupt mask bit is set to 1.
3. A vector address corresponding to the exception source is generated, and program execution
starts from that address.
For a reset exception, steps 2 and 3 above are carried out.
Rev. 3.00 Sep 14, 2005 page 73 of 910
REJ09B0258-0300
Section 4 Exception Handling
4.1.3
Exception Vector Table
The exception sources are classified as shown in figure 4.1. Different vectors are assigned to
different exception sources. Table 4.2 lists the exception sources and their vector addresses.
• Reset
External interrupts: NMI, IRQ 0 to IRQ5
Exception
sources
• Interrupts
• Trap instruction
Internal interrupts: 36 interrupts from on-chip
supporting modules
Figure 4.1 Exception Sources
Rev. 3.00 Sep 14, 2005 page 74 of 910
REJ09B0258-0300
Section 4 Exception Handling
Table 4.2
Exception Vector Table
Vector Address*1
Exception Source
Vector Number
Advanced Mode
Normal Mode
Reset
0
H'0000 to H'0003
H'0000 to H'0001
Reserved for system use
1
H'0004 to H'0007
H'0002 to H'0003
2
H'0008 to H'000B
H'0004 to H'0005
3
H'000C to H'000F
H'0006 to H'0007
4
H'0010 to H'0013
H'0008 to H'0009
5
H'0014 to H'0017
H'000A to H'000B
6
H'0018 to H'001B
H'000C to H'000D
External interrupt (NMI)
7
H'001C to H'001F
H'000E to H'000F
Trap instruction (4 sources)
8
H'0020 to H'0023
H'0010 to H'0011
9
H'0024 to H'0027
H'0012 to H'0013
10
H'0028 to H'002B
H'0014 to H'0015
11
H'002C to H'002F
H'0016 to H'0017
External interrupt IRQ0
12
H'0030 to H'0033
H'0018 to H'0019
External interrupt IRQ1
13
H'0034 to H'0037
H'001A to H'001B
External interrupt IRQ2
14
H'0038 to H'003B
H'001C to H'001D
External interrupt IRQ3
15
H'003C to H'003F
H'001E to H'001F
External interrupt IRQ4
16
H'0040 to H'0043
H'0020 to H'0021
External interrupt IRQ5
17
H'0044 to H'0047
H'0022 to H'0023
Reserved for system use
18
H'0048 to H'004B
H'0024 to H'0025
19
H'004C to H'004F
H'0026 to H'0027
20
to
63
H'0050 to H'0053
to
H'00FC to H'00FF
H'0028 to H'0029
to
H'007E to H'007F
2
Internal interrupts*
Notes: 1. Lower 16 bits of the address.
2. For the internal interrupt vectors, see section 5.3.3, Interrupt Vector Table.
Rev. 3.00 Sep 14, 2005 page 75 of 910
REJ09B0258-0300
Section 4 Exception Handling
4.2
Reset
4.2.1
Overview
A reset is the highest-priority exception. When the RES pin goes low, all processing halts and the
chip enters the reset state. A reset initializes the internal state of the CPU and the registers of the
on-chip supporting modules. Reset exception handling begins when the RES pin changes from
low to high.
The chip can also be reset by overflow of the watchdog timer. For details see section 12,
Watchdog Timer.
4.2.2
Reset Sequence
The chip enters the reset state when the RES pin goes low.
To ensure that the chip is reset, hold the RES pin low for at least 20 ms at power-up. To reset the
chip during operation, hold the RES pin low for at least 10 system clock (φ) cycles. When the
flash memory and flash memory R versions are used, the RES pin must be held low for at least 20
system clock cycles. See appendix D.2, Pin States at Reset, for the states of the pins in the reset
state.
When the RES pin goes high after being held low for the necessary time, the chip starts reset
exception handling as follows.
• The internal state of the CPU and the registers of the on-chip supporting modules are
initialized, and the I bit is set to 1 in CCR.
• The contents of the reset vector address (H'0000 to H'0003 in advanced mode, H'0000 to
H'0001 in normal mode) are read, and program execution starts from the address indicated in
the vector address.
Figure 4.2 shows the reset sequence in modes 1 and 3. Figure 4.3 shows the reset sequence in
modes 2 and 4. Figure 4.4 shows the reset sequence in mode 6.
Rev. 3.00 Sep 14, 2005 page 76 of 910
REJ09B0258-0300
(2)
(4)
(3)
(6)
(5)
(8)
(7)
Internal
processing
Address of reset vector: (1) = H'000000, (3) = H'000001, (5) = H'000002, (7) = H'000003
Start address (contents of reset exception handling vector address)
Start address
First instruction of program
High
(1)
Note: After a reset, the wait-state controller inserts three wait states in every bus cycle.
(1), (3), (5), (7)
(2), (4), (6), (8)
(9)
(10)
D15 to D8
HWR , LWR
RD
Address
bus
RES
φ
Vector fetch
(10)
(9)
Prefetch of
first program
instruction
Section 4 Exception Handling
Figure 4.2 Reset Sequence (Modes 1 and 3)
Rev. 3.00 Sep 14, 2005 page 77 of 910
REJ09B0258-0300
Section 4 Exception Handling
Internal
processing
Vector fetch
Prefetch of first
program instruction
φ
RES
Address bus
(1)
(3)
(5)
RD
HWR , LWR
D15 to D0
(1), (3)
(2), (4)
(5)
(6)
High
(2)
(4)
(6)
Address of reset vector: (1) = H'000000, (3) = H'000002
Start address (contents of reset exception handling vector address)
Start address
First instruction of program
Note: After a reset, the wait-state controller inserts three wait states in every bus cycle.
Figure 4.3 Reset Sequence (Modes 2 and 4)
Rev. 3.00 Sep 14, 2005 page 78 of 910
REJ09B0258-0300
Section 4 Exception Handling
Vector fetch
Internal
processing
Prefetch of
first program
instruction
φ
RES
Internal
address bus
(1)
(2)
Internal
read signal
Internal
write signal
Internal
data bus
(16 bits wide)
(2)
(3)
(1) Address of reset vector (H'0000)
(2) Start address (contents of reset exception handling vector address)
(3) First instruction of program
Figure 4.4 Reset Sequence (Mode 6)
4.2.3
Interrupts after Reset
If an interrupt is accepted after a reset but before the stack pointer (SP) is initialized, PC and CCR
will not be saved correctly, leading to a program crash. To prevent this, all interrupt requests,
including NMI, are disabled immediately after a reset. The first instruction of the program is
always executed immediately after the reset state ends. This instruction should initialize the stack
pointer (example: MOV.L #xx:32, SP).
Rev. 3.00 Sep 14, 2005 page 79 of 910
REJ09B0258-0300
Section 4 Exception Handling
4.3
Interrupts
Interrupt exception handling can be requested by seven external sources (NMI, IRQ0 to IRQ5),
and 36 internal sources in the on-chip supporting modules. Figure 4.5 classifies the interrupt
sources and indicates the number of interrupts of each type.
The on-chip supporting modules that can request interrupts are the watchdog timer (WDT),
DRAM interface, 16-bit timer, 8-bit timer, DMA controller (DMAC), serial communication
interface (SCI), and A/D converter. Each interrupt source has a separate vector address.
NMI is the highest-priority interrupt and is always accepted*. Interrupts are controlled by the
interrupt controller. The interrupt controller can assign interrupts other than NMI to two priority
levels, and arbitrate between simultaneous interrupts. Interrupt priorities are assigned in interrupt
priority registers A and B (IPRA and IPRB) in the interrupt controller.
Note: * In the flash memory and flash memory R versions, NMI input is sometimes disabled. For
details see section18.9, NMI Input Disable Conditions.
For details on interrupts see section 5, Interrupt Controller.
External interrupts
NMI (1)
IRQ 0 to IRQ 5 (6)
Internal interrupts
WDT*1 (1)
DRAM interface*2 (1)
16-bit timer (9)
8-bit timer (8)
DMAC (4)
SCI (12)
A/D converter (1)
Interrupts
Notes: Numbers in parentheses are the number of interrupt sources.
1. When the watchdog timer is used as an interval timer, it generates an interrupt request
at every counter overflow.
2. When the DRAM interface is used as an interval timer, it generates an interrupt request
at compare match.
Figure 4.5 Interrupt Sources and Number of Interrupts
Rev. 3.00 Sep 14, 2005 page 80 of 910
REJ09B0258-0300
Section 4 Exception Handling
4.4
Trap Instruction
Trap instruction exception handling starts when a TRAPA instruction is executed. If the UE bit is
set to 1 in the system control register (SYSCR), the exception handling sequence sets the I bit to 1
in CCR. If the UE bit is 0, the I and UI bits are both set to 1. The TRAPA instruction fetches a
start address from a vector table entry corresponding to a vector number from 0 to 3, which is
specified in the instruction code.
Rev. 3.00 Sep 14, 2005 page 81 of 910
REJ09B0258-0300
Section 4 Exception Handling
4.5
Stack Status after Exception Handling
Figure 4.6 shows the stack after completion of trap instruction exception handling and interrupt
exception handling.
SP–4
SP–3
SP–2
SP–1
SP (ER7) →
SP (ER7) →
SP+1
SP+2
SP+3
SP+4
Stack area
Before exception handling
CCR
CCR*
PC H
PC L
Even address
After exception handling
Pushed on stack
a. Normal mode
SP–4
SP–3
SP–2
SP–1
SP (ER7) →
SP (ER7) →
SP+1
SP+2
SP+3
SP+4
Stack area
Before exception handling
CCR
PC E
PC H
PC L
Even address
After exception handling
Pushed on stack
b. Advanced mode
Legend
PCE: Bits 23 to 16 of program counter (PC)
PCH: Bits 15 to 8 of program counter (PC)
PCL: Bits 7 to 0 of program counter (PC)
CCR: Condition code register
SP: Stack pointer
Notes: * Ignored at return.
1. PC indicates the address of the first instruction that will be executed after return.
2. Registers must be saved in word or longword size at even addresses.
Figure 4.6 Stack after Completion of Exception Handling
Rev. 3.00 Sep 14, 2005 page 82 of 910
REJ09B0258-0300
Section 4 Exception Handling
4.6
Notes on Stack Usage
When accessing word data or longword data, the H8/3068F regards the lowest address bit as 0.
The stack should always be accessed by word access or longword access, and the value of the
stack pointer (SP, ER7) should always be kept even.
Use the following instructions to save registers:
PUSH.W Rn
(or MOV.W Rn, @–SP)
PUSH.L ERn
(or MOV.L ERn, @–SP)
Use the following instructions to restore registers:
POP.W Rn
(or MOV.W @SP+, Rn)
POP.L ERn
(or MOV.L @SP+, ERn)
Setting SP to an odd value may lead to a malfunction. Figure 4.7 shows an example of what
happens when the SP value is odd.
Rev. 3.00 Sep 14, 2005 page 83 of 910
REJ09B0258-0300
Section 4 Exception Handling
CCR
SP
R1L
H'FFFEFA
H'FFFEFB
SP
PC
PC
H'FFFEFC
H'FFFEFD
H'FFFEFF
SP
TRAPA instruction executed
SP set to H'FFFEFF
MOV. B R1L, @-ER7
Data saved above SP
CCR contents lost
Legend
CCR: Condition code register
PC: Program counter
R1L: General register R1L
SP: Stack pointer
Note: The diagram illustrates modes 3 and 4.
Figure 4.7 Operation when SP Value is Odd
Rev. 3.00 Sep 14, 2005 page 84 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Section 5 Interrupt Controller
5.1
Overview
5.1.1
Features
The interrupt controller has the following features:
• Interrupt priority registers (IPRs) for setting interrupt priorities
• Interrupts other than NMI can be assigned to two priority levels on a module-by-module basis
in interrupt priority registers A and B (IPRA and IPRB).
• Three-level masking by the I and UI bits in the CPU condition code register (CCR)
• Seven external interrupt pins
NMI has the highest priority and is always accepted*; either the rising or falling edge can be
selected. For each of IRQ0 to IRQ5, sensing of the falling edge or level sensing can be selected
independently.
Note: * In the flash memory and flash memory R versions, NMI input is sometimes disabled. For
details see section18.9, NMI Input Disable Conditions.
Rev. 3.00 Sep 14, 2005 page 85 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.1.2
Block Diagram
Figure 5.1 shows a block diagram of the interrupt controller.
CPU
ISCR
IER
IPRA, IPRB
NMI
input
IRQ input
section ISR
IRQ input
OVF
TME
.
.
.
.
.
.
.
TEI
TEIE
Priority
decision logic
Interrupt
request
Vector
number
.
.
.
I
UI
Interrupt controller
UE
SYSCR
Legend
ISCR:
IER:
ISR:
IPRA:
IPRB:
SYSCR:
IRQ sense control register
IRQ enable register
IRQ status register
Interrupt priority register A
Interrupt priority register B
System control register
Figure 5.1 Interrupt Controller Block Diagram
Rev. 3.00 Sep 14, 2005 page 86 of 910
REJ09B0258-0300
CCR
Section 5 Interrupt Controller
5.1.3
Pin Configuration
Table 5.1 lists the interrupt pins.
Table 5.1
Interrupt Pins
Name
Abbreviation I/O
Nonmaskable interrupt
NMI
External interrupt request 5 to 0
IRQ5
Function
Input Nonmaskable interrupt*, rising edge or
falling edge selectable
to IRQ0
Input Maskable interrupts, falling edge or level
sensing selectable
Note: * NMI input is sometimes disabled. For details see 18.9, NMI Input Disabling Conditions.
5.1.4
Register Configuration
Table 5.2 lists the registers of the interrupt controller.
Table 5.2
Interrupt Controller Registers
Address*1
Name
Abbreviation
R/W
Initial Value
H'EE012
System control register
SYSCR
R/W
H'09
H'EE014
IRQ sense control register
ISCR
R/W
H'00
H'EE015
IRQ enable register
IER
R/W
H'00
H'EE016
IRQ status register
ISR
R/(W)*2
H'00
H'EE018
Interrupt priority register A
IPRA
R/W
H'00
H'EE019
Interrupt priority register B
IPRB
R/W
H'00
Notes: 1. Lower 20 bits of the address in advanced mode.
2. Only 0 can be written, to clear flags.
Rev. 3.00 Sep 14, 2005 page 87 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.2
Register Descriptions
5.2.1
System Control Register (SYSCR)
SYSCR is an 8-bit readable/writable register that controls software standby mode, selects the
action of the UI bit in CCR, selects the NMI edge, and enables or disables the on-chip RAM.
Only bits 3 and 2 are described here. For the other bits, see section 3.3, System Control Register
(SYSCR).
SYSCR is initialized to H'09 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
Initial value
0
0
0
0
1
0
0
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RAM enable
Software standby
output port enable
Standby timer
select 2 to 0
Software standby
Rev. 3.00 Sep 14, 2005 page 88 of 910
REJ09B0258-0300
NMI edge select
Selects the NMI input edge
User bit enable
Selects whether to use the UI bit in
CCR as a user bit or interrupt mask bit
Section 5 Interrupt Controller
Bit 3—User Bit Enable (UE): Selects whether to use the UI bit in CCR as a user bit or an
interrupt mask bit.
Bit 3
UE
Description
0
UI bit in CCR is used as interrupt mask bit
1
UI bit in CCR is used as user bit
(Initial value)
Bit 2—NMI Edge Select (NMIEG): Selects the NMI input edge.
Bit 2
NMIEG
Description
0
Interrupt is requested at falling edge of NMI input
1
Interrupt is requested at rising edge of NMI input
5.2.2
(Initial value)
Interrupt Priority Registers A and B (IPRA, IPRB)
IPRA and IPRB are 8-bit readable/writable registers that control interrupt priority.
Rev. 3.00 Sep 14, 2005 page 89 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Interrupt Priority Register A (IPRA): IPRA is an 8-bit readable/writable register in which
interrupt priority levels can be set.
Bit
7
6
5
4
3
2
1
0
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Priority
level A0
Selects the
priority level
of 16-bit timer
channel 2
interrupt
requests
Priority level A1
Selects the priority level
of 16-bit timer channel 1
interrupt requests
Priority level A2
Selects the priority level of
16-bit timer channel 0 interrupt
requests
Priority level A3
Selects the priority level of WDT,
DRAM interface, and A/D converter
interrupt requests
Priority level A4
Selects the priority level of IRQ4 and IRQ 5
interrupt requests
Priority level A5
Selects the priority level of IRQ 2 and IRQ 3 interrupt requests
Priority level A6
Selects the priority level of IRQ1 interrupt requests
Priority level A7
Selects the priority level of IRQ 0 interrupt requests
IPRA is initialized to H'00 by a reset and in hardware standby mode.
Rev. 3.00 Sep 14, 2005 page 90 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Bit 7—Priority Level A7 (IPRA7): Selects the priority level of IRQ0 interrupt requests.
Bit 7
IPRA7
Description
0
IRQ0 interrupt requests have priority level 0 (low priority)
1
IRQ0 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 6—Priority Level A6 (IPRA6): Selects the priority level of IRQ1 interrupt requests.
Bit 6
IPRA6
Description
0
IRQ1 interrupt requests have priority level 0 (low priority)
1
IRQ1 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 5—Priority Level A5 (IPRA5): Selects the priority level of IRQ2 and IRQ3 interrupt
requests.
Bit 5
IPRA5
Description
0
IRQ2 and IRQ3 interrupt requests have priority level 0 (low priority)
1
IRQ2 and IRQ3 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 4—Priority Level A4 (IPRA4): Selects the priority level of IRQ4 and IRQ5 interrupt
requests.
Bit 4
IPRA4
Description
0
IRQ4 and IRQ5 interrupt requests have priority level 0 (low priority)
1
IRQ4 and IRQ5 interrupt requests have priority level 1 (high priority)
(Initial value)
Rev. 3.00 Sep 14, 2005 page 91 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Bit 3—Priority Level A3 (IPRA3): Selects the priority level of WDT, DRAM interface, and
A/D converter interrupt requests.
Bit 3
IPRA3
Description
0
WDT, DRAM interface, and A/D converter interrupt requests have priority level 0
(low priority)
(Initial value)
1
WDT, DRAM interface, and A/D converter interrupt requests have priority level 1
(high priority)
Bit 2—Priority Level A2 (IPRA2): Selects the priority level of 16-bit timer channel 0 interrupt
requests.
Bit 2
IPRA2
Description
0
16-bit timer channel 0 interrupt requests have priority level 0 (low priority)(Initial value)
1
16-bit timer channel 0 interrupt requests have priority level 1 (high priority)
Bit 1—Priority Level A1 (IPRA1): Selects the priority level of 16-bit timer channel 1 interrupt
requests.
Bit 1
IPRA1
Description
0
16-bit timer channel 1 interrupt requests have priority level 0 (low priority)(Initial value)
1
16-bit timer channel 1 interrupt requests have priority level 1 (high priority)
Bit 0—Priority Level A0 (IPRA0): Selects the priority level of 16-bit timer channel 2 interrupt
requests.
Bit 0
IPRA0
Description
0
16-bit timer channel 2 interrupt requests have priority level 0 (low priority)(Initial value)
1
16-bit timer channel 2 interrupt requests have priority level 1 (high priority)
Rev. 3.00 Sep 14, 2005 page 92 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Interrupt Priority Register B (IPRB): IPRB is an 8-bit readable/writable register in which
interrupt priority levels can be set.
Bit
7
6
5
4
3
2
1
0
IPRB7
IPRB6
IPRB5

IPRB3
IPRB2
IPRB1

Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bit
Priority level B1
Selects the priority level
of SCI channel 2 interrupt
requests
Priority level B2
Selects the priority level of
SCI channel 1 interrupt requests
Priority level B3
Selects the priority level of SCI
channel 0 interrupt requests
Reserved bit
Priority level B5
Selects the priority level of DMAC
interrupt requests (channels 0 and 1)
Priority level B6
Selects the priority level of 8-bit timer channel 2, 3 interrupt requests
Priority level B7
Selects the priority level of 8-bit timer channel 0, 1 interrupt requests
IPRB is initialized to H'00 by a reset and in hardware standby mode.
Rev. 3.00 Sep 14, 2005 page 93 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Bit 7—Priority Level B7 (IPRB7): Selects the priority level of 8-bit timer channel 0, 1 interrupt
requests.
Bit 7
IPRB7
Description
0
8-bit timer channel 0, 1 interrupt requests have priority level 0 (low priority)(Initial value)
1
8-bit timer channel 0, 1 interrupt requests have priority level 1 (high priority)
Bit 6—Priority Level B6 (IPRB6): Selects the priority level of 8-bit timer channel 2, 3 interrupt
requests.
Bit 6
IPRB6
Description
0
8-bit timer channel 2, 3 interrupt requests have priority level 0 (low priority)(Initial value)
1
8-bit timer channel 2, 3 interrupt requests have priority level 1 (high priority)
Bit 5—Priority Level B5 (IPRB5): Selects the priority level of DMAC interrupt requests
(channels 0 and 1).
Bit 5
IPRB5
Description
0
DMAC interrupt requests (channels 0 and 1) have priority level 0
(low priority)
(Initial value)
1
DMAC interrupt requests (channels 0 and 1) have priority level 1 (high priority)
Bit 4—Reserved: This bit can be written and read, but it does not affect interrupt priority.
Bit 3—Priority Level B3 (IPRB3): Selects the priority level of SCI channel 0 interrupt requests.
Bit 3
IPRB3
Description
0
SCI0 interrupt requests have priority level 0 (low priority)
1
SCI0 interrupt requests have priority level 1 (high priority)
Rev. 3.00 Sep 14, 2005 page 94 of 910
REJ09B0258-0300
(Initial value)
Section 5 Interrupt Controller
Bit 2—Priority Level B2 (IPRB2): Selects the priority level of SCI channel 1 interrupt requests.
Bit 2
IPRB2
Description
0
SCI1 interrupt requests have priority level 0 (low priority)
1
SCI1 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 1—Priority Level B1 (IPRB1): Selects the priority level of SCI channel 2 interrupt requests.
Bit 1
IPRB1
Description
0
SCI channel 2 interrupt requests have priority level 0 (low priority)
1
SCI channel 2 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 0—Reserved: This bit can be written and read, but it does not affect interrupt priority.
Rev. 3.00 Sep 14, 2005 page 95 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.2.3
IRQ Status Register (ISR)
ISR is an 8-bit readable/writable register that indicates the status of IRQ0 to IRQ5 interrupt
requests.
Bit
7
6
5
4
3
2
1
0
—
—
IRQ5F
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
Initial value
0
0
0
0
0
0
0
0
Read/Write
—
—
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
Reserved bits
IRQ 5 to IRQ0 flags
These bits indicate IRQ 5 to IRQ 0
interrupt request status
Note: * Only 0 can be written, to clear flags.
ISR is initialized to H'00 by a reset and in hardware standby mode.
Bits 7 and 6—Reserved: These bits can not be modified and are always read as 0.
Bits 5 to 0—IRQ5 to IRQ0 Flags (IRQ5F to IRQ0F): These bits indicate the status of IRQ5 to
IRQ0 interrupt requests.
Bits 5 to 0
IRQ5F to IRQ0F Description
0
[Clearing conditions]
(Initial value)
0 is written in IRQnF after reading the IRQnF flag when IRQnF = 1.
IRQnSC = 0, IRQn input is high, and interrupt exception handling is carried out.
IRQnSC = 1 and IRQn interrupt exception handling is carried out.
1
[Setting conditions]
IRQnSC = 0 and IRQn input is low.
IRQnSC = 1 and IRQn input changes from high to low.
Note: n = 5 to 0
Rev. 3.00 Sep 14, 2005 page 96 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.2.4
IRQ Enable Register (IER)
IER is an 8-bit readable/writable register that enables or disables IRQ5 to IRQ0 interrupt requests.
Bit
7
6
5
4
3
2
1
0


IRQ5E
IRQ4E
IRQ3E
IRQ2E
IRQ1E
IRQ0E
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bits
IRQ 5 to IRQ0 enable
These bits enable or disable IRQ 5 to IRQ 0 interrupts
IER is initialized to H'00 by a reset and in hardware standby mode.
Bits 7 and 6—Reserved: These bits can be written and read, but they do not enable or disable
interrupts.
Bits 5 to 0—IRQ5 to IRQ0 Enable (IRQ5E to IRQ0E): These bits enable or disable
IRQ5 to IRQ0 interrupts.
Bits 5 to 0
IRQ5E to IRQ0E Description
0
IRQ5 to IRQ0 interrupts are disabled
1
IRQ5 to IRQ0 interrupts are enabled
(Initial value)
Rev. 3.00 Sep 14, 2005 page 97 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.2.5
IRQ Sense Control Register (ISCR)
ISCR is an 8-bit readable/writable register that selects level sensing or falling-edge sensing of the
inputs at pins IRQ5 to IRQ0.
Bit
7
6


Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
5
4
3
2
1
0
IRQ5SC IRQ4SC IRQ3SC IRQ2SC IRQ1SC IRQ0SC
Reserved bits
IRQ 5 to IRQ0 sense control
These bits select level sensing or falling-edge
sensing for IRQ 5 to IRQ 0 interrupts
ISCR is initialized to H'00 by a reset and in hardware standby mode.
Bits 7 and 6—Reserved: These bits can be written and read, but they do not select level or
falling-edge sensing.
Bits 5 to 0—IRQ5 to IRQ0 Sense Control (IRQ5SC to IRQ0SC): These bits select whether
interrupts IRQ5 to IRQ0 are requested by level sensing of pins IRQ5 to IRQ0, or by falling-edge
sensing.
Bits 5 to 0
IRQ5SC to IRQ0SC Description
0
Interrupts are requested when IRQ5 to IRQ0 inputs are low
1
Interrupts are requested by falling-edge input at IRQ5 to IRQ0
Rev. 3.00 Sep 14, 2005 page 98 of 910
REJ09B0258-0300
(Initial value)
Section 5 Interrupt Controller
5.3
Interrupt Sources
The interrupt sources include external interrupts (NMI, IRQ0 to IRQ5) and 36 internal interrupts.
5.3.1
External Interrupts
There are seven external interrupts: NMI, and IRQ0 to IRQ5. Of these, NMI, IRQ0, IRQ1, and
IRQ2 can be used to exit software standby mode.
NMI: NMI is the highest-priority interrupt and is always accepted, regardless of the states of the I
and UI bits in CCR*. The NMIEG bit in SYSCR selects whether an interrupt is requested by the
rising or falling edge of the input at the NMI pin. NMI interrupt exception handling has vector
number 7.
Note: * NMI input is sometimes disabled. For details see section18.9, NMI Input Disabling
Conditions.
IRQ0 to IRQ5 Interrupts: These interrupts are requested by input signals at pins IRQ0 to IRQ5.
The IRQ0 to IRQ5 interrupts have the following features.
• ISCR settings can select whether an interrupt is requested by the low level of the input at pins
IRQ0 to IRQ5, or by the falling edge.
• IER settings can enable or disable the IRQ0 to IRQ5 interrupts. Interrupt priority levels can be
assigned by four bits in IPRA (IPRA7 to IPRA4).
• The status of IRQ0 to IRQ5 interrupt requests is indicated in ISR. The ISR flags can be cleared
to 0 by software.
Figure 5.2 shows a block diagram of interrupts IRQ0 to IRQ5.
IRQnSC
IRQnE
IRQnF
Edge/level
sense circuit
IRQn input
S
Q
IRQn interrupt
request
R
Clear signal
Note: n = 5 to 0
Figure 5.2 Block Diagram of Interrupts IRQ0 to IRQ5
Rev. 3.00 Sep 14, 2005 page 99 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Figure 5.3 shows the timing of the setting of the interrupt flags (IRQnF).
φ
IRQn
input pin
IRQnF
Note: n = 5 to 0
Figure 5.3 Timing of Setting of IRQnF
Interrupts IRQ0 to IRQ5 have vector numbers 12 to 17. These interrupts are detected regardless of
whether the corresponding pin is set for input or output. When using a pin for external interrupt
input, clear its DDR bit to 0 and do not use the pin for chip select output, refresh output, SCI
input/output, or A/D external trigger input.
5.3.2
Internal Interrupts
Thirty-Six internal interrupts are requested from the on-chip supporting modules.
• Each on-chip supporting module has status flags for indicating interrupt status, and enable bits
for enabling or disabling interrupts.
• Interrupt priority levels can be assigned in IPRA and IPRB.
• 16-bit timer, SCI, and A/D converter interrupt requests can activate the DMAC, in which case
no interrupt request is sent to the interrupt controller, and the I and UI bits are disregarded.
5.3.3
Interrupt Vector Table
Table 5.3 lists the interrupt sources, their vector addresses, and their default priority order. In the
default priority order, smaller vector numbers have higher priority. The priority of interrupts other
than NMI can be changed in IPRA and IPRB. The priority order after a reset is the default order
shown in table 5.3.
Rev. 3.00 Sep 14, 2005 page 100 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Table 5.3
Interrupt Sources, Vector Addresses, and Priority
Interrupt Source
Origin
NMI
External
pins
Vector Address*
Vector
Number Advanced Mode Normal Mode
IPR
7
H'001C to H'001F H'000E to H'000F —
12
H'0030 to H'0033
H'0018 to H'0019
IRQ1
13
H'0034 to H0037
H'001A to H'001B IPRA6
IRQ2
IRQ3
14
15
H'0038 to H'003B H'001C to H'001D IPRA5
H'003C to H'003F H'001E to H'001F
IRQ4
IRQ5
16
17
H'0040 to H'0043
H'0044 to H'0047
IRQ0
H'0020 to H'0021
H'0022 to H'0023
Reserved
—
18
19
H'0048 to H'004B H'0024 to H'0025
H'004C to H'004F H'0026 to H'0027
WOVI
(interval timer)
Watchdog
timer
20
H'0050 to H'0053
H'0028 to H'0029
CMI
(compare match)
DRAM
interface
21
H'0054 to H'0057
H'002A to H'002B
Reserved
—
22
H'0058 to H'005B H'002C to H'002D
ADI (A/D end)
A/D
23
H'005C to H'005F H'002E to H'002F
IMIA0
(compare match/
input capture A0)
IMIB0
(compare match/
input capture B0)
OVI0 (overflow 0)
16-bit timer 24
channel 0
H'0060 to H'0063
H'0030 to H'0031
25
H'0064 to H'0067
H'0032 to H'0033
26
H'0068 to H'006B H'0034 to H'0035
Reserved
—
27
H'006C to H'006F H'0036 to H'0037
IMIA1
(compare match/
inputcapture A1)
IMIB1
(compare match/
input capture B1)
OVI1 (overflow 1)
16-bit timer 28
channel 1
H'0070 to H'0073
H'0038 to H'0039
29
H'0074 to H'0077
H'003A to H'003B
30
H'0078 to H'007B H'003C to H'003D
Reserved
—
31
H'007C to H'007F H'003E to H'003F
Priority
High
IPRA7
IPRA4
IPRA3
IPRA2
IPRA1
Low
Note: * Lower 16 bits of the address.
Rev. 3.00 Sep 14, 2005 page 101 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Vector Address*
Vector
Number Advanced Mode Normal Mode
Interrupt Source
Origin
IMIA2
(compare match/
input capture A2)
IMIB2
(compare match/
input capture B2)
OVI2 (overflow 2)
16-bit timer 32
channel 2
H'0080 to H'0083
H'0040 to H'0041
33
H'0084 to H'0087
H'0042 to H'0043
34
H'0088 to H'008B H'0044 to H'0045
Reserved
—
35
H'008C to H'008F H'0046 to H'0047
CMIA0
(compare match
A0)
CMIB0
(compare match
B0)
CMIA1/CMIB1
(compare match
A1/B1)
TOVI0/TOVI1
(overflow 0/1)
8-bit timer 36
channel 0/1
H'0090 to H'0093
H'0048 to H'0049
37
H'0094 to H'0097
H'004A to H'004B
38
H'0098 to H'009B H'004C to H'004D
39
H'009C to H'009F H'004E to H'004F
CMIA2
(compare match
A2)
CMIB2
(compare match
B2)
CMIA3/CMIB3
(compare match
A3/B3)
TOVI2/TOVI3
(overflow 2/3)
8-bit timer 40
channel 2/3
H'00A0 to H'00A3 H'0050 to H'0051
41
H'00A4 to H'00A7 H'0052 to H'0053
42
H'00A8 to H'00AB H'0054 to H'0055
43
H'00AC to H'00AF H'0056 to H'0057
DEND0A
DEND0B
DEND1A
DEND1B
DMAC
44
45
46
47
H'00B0 to H'00B3
H'00B4 to H'00B7
H'00B8 to H'00BB
H'00BC to H'00BF
H'0058 to H'0059 IPRB5
H'005A to H'005B
H'005C to H'005D
H'005E to H'005F
Reserved
—
48
49
50
51
H'00C0 to H'00C3
H'00C4 to H'00C7
H'00C8 to H'00CB
H'00CC to H'00CF
H'0060 to H'0061
H'0062 to H'0063
H'0064 to H'0065
H'0066 to H'0067
Note: * Lower 16 bits of the address.
Rev. 3.00 Sep 14, 2005 page 102 of 910
REJ09B0258-0300
IPR
Priority
IPRA0
High
IPRB7
IPRB6
—
Low
Section 5 Interrupt Controller
Interrupt Source
Origin
ERI0
(receive error 0)
RXI0 (receive
data full 0)
TXI0 (transmit
data empty 0)
TEI0
(transmit end 0)
SCI
channel 0
ERI1
(receive error 1)
RXI1 (receive
data full 1)
TXI1 (transmit
data empty 1)
TEI1 (transmit
end 1)
SCI
channel 1
ERI2
(receive error 2)
RXI2 (receive
data full 2)
TXI2 (transmit
data empty 2)
TEI2 (transmit
end 2)
SCI
channel 2
Vector Address*
Vector
Number Advanced Mode Normal Mode
IPR
Priority
52
H'00D0 to H'00D3 H'0068 to H'0069
IPRB3
High
53
H'00D4 to H'00D7 H'006A to H'006B
54
H'00D8 to H'00DB H'006C to H'006D
55
H'00DC to H'00DF H'006E to H'006F
56
H'00E0 to H'00E3 H'0070 to H'0071
57
H'00E4 to H'00E7 H'0072 to H'0073
58
H'00E8 to H'00EB H'0074 to H'0075
59
H'00EC to H'00EF H'0076 to H'0077
60
H'00F0 to H'00F3 H'0078 to H'0079
61
H'00F4 to H'00F7 H'007A to H'007B
62
H'00F8 to H'00FB H'007C to H'007D
63
H'00FC to H'00FF H'007E to H'007F
IPRB2
IPRB1
Low
Note: * Lower 16 bits of the address.
Rev. 3.00 Sep 14, 2005 page 103 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.4
Interrupt Operation
5.4.1
Interrupt Handling Process
The H8/3068F handles interrupts differently depending on the setting of the UE bit. When UE =
1, interrupts are controlled by the I bit. When UE = 0, interrupts are controlled by the I and UI
bits. Table 5.4 indicates how interrupts are handled for all setting combinations of the UE, I, and
UI bits.
NMI interrupts are always accepted except in the reset and hardware standby states*. IRQ
interrupts and interrupts from the on-chip supporting modules have their own enable bits.
Interrupt requests are ignored when the enable bits are cleared to 0.
Note: * NMI input is sometimes disabled. For details see section 18.9, NMI Input Disabling
Conditions.
Table 5.4
UE, I, and UI Bit Settings and Interrupt Handling
SYSCR
CCR
UE
I
UI
Description
1
0
—
All interrupts are accepted. Interrupts with priority level 1 have higher
priority.
1
—
No interrupts are accepted except NMI.
0
—
All interrupts are accepted. Interrupts with priority level 1 have higher
priority.
1
0
NMI and interrupts with priority level 1 are accepted.
1
No interrupts are accepted except NMI.
0
UE = 1: Interrupts IRQ0 to IRQ5 and interrupts from the on-chip supporting modules can all be
masked by the I bit in the CPU’s CCR. Interrupts are masked when the I bit is set to 1, and
unmasked when the I bit is cleared to 0. Interrupts with priority level 1 have higher priority.
Figure 5.4 is a flowchart showing how interrupts are accepted when UE = 1.
Rev. 3.00 Sep 14, 2005 page 104 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Program execution state
No
Interrupt requested?
Yes
Yes
NMI
No
No
Pending
Priority level 1?
Yes
IRQ 0
No
Yes
IRQ 1
IRQ 0
No
Yes
No
IRQ 1
Yes
No
Yes
TEI2
TEI2
Yes
Yes
No
I=0
Yes
Save PC and CCR
I ←1
Read vector address
Branch to interrupt
service routine
Figure 5.4 Process Up to Interrupt Acceptance when UE = 1
Rev. 3.00 Sep 14, 2005 page 105 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
• If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an
interrupt request is sent to the interrupt controller.
• When the interrupt controller receives one or more interrupt requests, it selects the highestpriority request, following the IPR interrupt priority settings, and holds other requests
pending. If two or more interrupts with the same IPR setting are requested simultaneously, the
interrupt controller follows the priority order shown in table 5.3.
• The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt
request is accepted. If the I bit is set to 1, only NMI is accepted; other interrupt requests are
held pending.
• When an interrupt request is accepted, interrupt exception handling starts after execution of
the current instruction has been completed.
• In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is
saved indicates the address of the first instruction that will be executed after the return from
the interrupt service routine.
• Next the I bit is set to 1 in CCR, masking all interrupts except NMI.
• The vector address of the accepted interrupt is generated, and the interrupt service routine
starts executing from the address indicated by the contents of the vector address.
UE = 0: The I and UI bits in the CPU’s CCR and the IPR bits enable three-level masking of
IRQ0 to IRQ5 interrupts and interrupts from the on-chip supporting modules.
• Interrupt requests with priority level 0 are masked when the I bit is set to 1, and are unmasked
when the I bit is cleared to 0.
• Interrupt requests with priority level 1 are masked when the I and UI bits are both set to 1, and
are unmasked when either the I bit or the UI bit is cleared to 0.
For example, if the interrupt enable bits of all interrupt requests are set to 1, IPRA is set to
H'20, and IPRB is set to H'00 (giving IRQ2 and IRQ3 interrupt requests priority over other
interrupts), interrupts are masked as follows:
a. If I = 0, all interrupts are unmasked (priority order: NMI > IRQ2 > IRQ3 >IRQ0 …).
b. If I = 1 and UI = 0, only NMI, IRQ2, and IRQ3 are unmasked.
c. If I = 1 and UI = 1, all interrupts are masked except NMI.
Rev. 3.00 Sep 14, 2005 page 106 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Figure 5.5 shows the transitions among the above states.
I←0
a. All interrupts are
unmasked
I←0
b. Only NMI, IRQ 2 , and
IRQ 3 are unmasked
I ← 1, UI ← 0
Exception handling,
or I ← 1, UI ← 1
UI ← 0
Exception handling,
or UI ← 1
c. All interrupts are
masked except NMI
Figure 5.5 Interrupt Masking State Transitions (Example)
Figure 5.6 is a flowchart showing how interrupts are accepted when UE = 0.
• If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an
interrupt request is sent to the interrupt controller.
• When the interrupt controller receives one or more interrupt requests, it selects the highestpriority request, following the IPR interrupt priority settings, and holds other requests
pending. If two or more interrupts with the same IPR setting are requested simultaneously, the
interrupt controller follows the priority order shown in table 5.3.
• The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt
request is accepted regardless of its IPR setting, and regardless of the UI bit. If the I bit is set
to 1 and the UI bit is cleared to 0, only NMI and interrupts with priority level 1 are accepted;
interrupt requests with priority level 0 are held pending. If the I bit and UI bit are both set to 1,
only NMI is accepted; all other interrupt requests are held pending.
• When an interrupt request is accepted, interrupt exception handling starts after execution of
the current instruction has been completed.
• In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is
saved indicates the address of the first instruction that will be executed after the return from
the interrupt service routine.
• The I and UI bits are set to 1 in CCR, masking all interrupts except NMI.
• The vector address of the accepted interrupt is generated, and the interrupt service routine
starts executing from the address indicated by the contents of the vector address.
Rev. 3.00 Sep 14, 2005 page 107 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
Program execution state
No
Interrupt requested?
Yes
Yes
NMI
No
No
Pending
Priority level 1?
Yes
IRQ 0
No
IRQ 0
Yes
IRQ 1
No
Yes
No
IRQ 1
Yes
No
Yes
TEI2
TEI2
Yes
Yes
No
I=0
No
I=0
Yes
Yes
No
UI = 0
Yes
Save PC and CCR
I ← 1, UI ← 1
Read vector address
Branch to interrupt
service routine
Figure 5.6 Process Up to Interrupt Acceptance when UE = 0
Rev. 3.00 Sep 14, 2005 page 108 of 910
REJ09B0258-0300
(2)
(1)
(4)
High
(3)
Instruction Internal
prefetch
processing
(8)
(7)
(10)
(9)
(12)
(11)
Vector fetch
(14)
(13)
(6), (8)
PC and CCR saved to stack
(9), (11) Vector address
(10), (12) Starting address of interrupt service routine (contents of
vector address)
(13)
Starting address of interrupt service routine; (13) = (10), (12)
(14)
First instruction of interrupt service routine
(6)
(5)
Stack
Prefetch of
interrupt
Internal
service routine
processing instruction
Note: Mode 2, with program code and stack in external memory area accessed in two states via 16-bit bus.
Instruction prefetch address (not executed;
return address, same as PC contents)
(2), (4) Instruction code (not executed)
(3)
Instruction prefetch address (not executed)
(5)
SP – 2
(7)
SP – 4
(1)
D15 to D0
HWR , LWR
RD
Address
bus
Interrupt
request
signal
φ
Interrupt level
decision and wait
for end of instruction
5.4.2
Interrupt accepted
Section 5 Interrupt Controller
Interrupt Sequence
Figure 5.7 shows the interrupt sequence in mode 2 when the program code and stack are in an
external memory area accessed in two states via a 16-bit bus.
Figure 5.7 Interrupt Sequence
Rev. 3.00 Sep 14, 2005 page 109 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.4.3
Interrupt Response Time
Table 5.5 indicates the interrupt response time from the occurrence of an interrupt request until
the first instruction of the interrupt service routine is executed.
Table 5.5
Interrupt Response Time
External Memory
No.
On-Chip
Memory
Item
1
8-Bit Bus
2 States
1
3 States
1
16-Bit Bus
2 States
1
3 States
2*1
1
Interrupt priority
decision
2*
2*
2*
2*
2
Maximum number
of states until end of
current instruction
1 to 23*5
1 to 27*5
1 to 41*4,*6
1 to 23*5
1 to 25*4,*5
3
Saving PC and CCR
to stack
4
8
12*4
4
6*4
4
Vector fetch
4
8
12*4
4
6*4
5
Instruction prefetch*2
4
8
12*4
4
6*4
6
3
4
4
4
4
4
19 to 41
31 to 57
43 to 83
19 to 41
25 to 49
Total
Internal processing*
Notes: 1. 1 state for internal interrupts.
2. Prefetch after the interrupt is accepted and prefetch of the first instruction in the
interrupt service routine.
3. Internal processing after the interrupt is accepted and internal processing after vector
fetch.
4. The number of states increases if wait states are inserted in external memory access.
5. Example for DIVXS.W Rs,ERd and MULXS.W Rs,ERd
6. Example for MOV.L @(d:24,ERs),ERd and MOV.L ERs,@(d:24,ERd)
Rev. 3.00 Sep 14, 2005 page 110 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.5
Usage Notes
5.5.1
Contention between Interrupt and Interrupt-Disabling Instruction
When an instruction clears an interrupt enable bit to 0 to disable the interrupt, the interrupt is not
disabled until after execution of the instruction is completed. If an interrupt occurs while a BCLR,
MOV, or other instruction is being executed to clear its interrupt enable bit to 0, at the instant
when execution of the instruction ends the interrupt is still enabled, so its interrupt exception
handling is carried out. If a higher-priority interrupt is also requested, however, interrupt
exception handling for the higher-priority interrupt is carried out, and the lower-priority interrupt
is ignored. This also applies to the clearing of an interrupt flag to 0.
Figure 5.8 shows an example in which an IMIEA bit is cleared to 0 in the 16-bit timer's TISRA
register.
TISRA write cycle by CPU
IMIA exception handling
φ
Internal
address bus
TISRA address
Internal
write signal
IMIEA
IMIA
IMFA interrupt
signal
Figure 5.8 Contention between Interrupt and Interrupt-Disabling Instruction
This type of contention will not occur if the interrupt is masked when the interrupt enable bit or
flag is cleared to 0.
Rev. 3.00 Sep 14, 2005 page 111 of 910
REJ09B0258-0300
Section 5 Interrupt Controller
5.5.2
Instructions that Inhibit Interrupts
The LDC, ANDC, ORC, and XORC instructions inhibit interrupts. When an interrupt occurs,
after determining the interrupt priority, the interrupt controller requests a CPU interrupt. If the
CPU is currently executing one of these interrupt-inhibiting instructions, however, when the
instruction is completed the CPU always continues by executing the next instruction.
5.5.3
Interrupts during EEPMOV Instruction Execution
The EEPMOV.B and EEPMOV.W instructions differ in their reaction to interrupt requests.
When the EEPMOV.B instruction is executing a transfer, no interrupts are accepted until the
transfer is completed, not even NMI.
When the EEPMOV.W instruction is executing a transfer, interrupt requests other than NMI are
not accepted until the transfer is completed. If NMI is requested, NMI exception handling starts
at a transfer cycle boundary. The PC value saved on the stack is the address of the next
instruction. Programs should be coded as follows to allow for NMI interrupts during EEPMOV.W
execution:
L1: EEPMOV.W
MOV.W R4,R4
BNE
L1
Rev. 3.00 Sep 14, 2005 page 112 of 910
REJ09B0258-0300
Section 6 Bus Controller
Section 6 Bus Controller
6.1
Overview
The H8/3068F has an on-chip bus controller (BSC) that manages the external address space
divided into eight areas. The bus specifications, such as bus width and number of access states,
can be set independently for each area, enabling multiple memories to be connected easily.
The bus controller also has a bus arbitration function that controls the operation of the internal
bus masters-the CPU, DMA controller (DMAC), and DRAM interface and can release the bus to
an external device.
6.1.1
Features
The features of the bus controller are listed below.
• Manages external address space in area units
 Manages the external space as eight areas (0 to 7) of 128 kbytes in 1M-byte modes, or 2
Mbytes in 16-Mbyte modes
 Bus specifications can be set independently for each area
 DRAM/burst ROM interfaces can be set
• Basic bus interface
 Chip select (CS0 to CS7) can be output for areas 0 to 7
 8-bit access or 16-bit access can be selected for each area
 Two-state access or three-state access can be selected for each area
 Program wait states can be inserted for each area
 Pin wait insertion capability is provided
• DRAM interface
 DRAM interface can be set for areas 2 to 5
 Row address/column address multiplexed output (8/9/10 bits)
 2-CAS byte access mode
 Burst operation (fast page mode)
 TP cycle insertion to secure RAS precharging time
 Choice of CAS-before-RAS refreshing or self-refreshing
• Burst ROM interface
 Burst ROM interface can be set for area 0
 Selection of two- or three-state burst access
Rev. 3.00 Sep 14, 2005 page 113 of 910
REJ09B0258-0300
Section 6 Bus Controller
• Idle cycle insertion
 An idle cycle can be inserted in case of an external read cycle between different areas
 An idle cycle can be inserted when an external read cycle is immediately followed by an
external write cycle
• Bus arbitration function
 A built-in bus arbiter grants the bus right to the CPU, DMAC, DRAM interface, or an
external bus master
• Other features
 Refresh counter (refresh timer) can be used as interval timer
 Choice of two address update modes
Rev. 3.00 Sep 14, 2005 page 114 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.1.2
Block Diagram
Figure 6.1 shows a block diagram of the bus controller.
CS0 to CS7
ABWCR
ASTCR
BCR
Internal address bus
Area
decoder
Chip select
control signals
CSCR
Internal signals
ADRCR
Bus mode control signal
Bus size control signal
Bus control
circuit
Internal data bus
Access state control signal
Wait state
controller
WAIT
Wait request signal
WCRH
WCRL
Internal signals
CPU bus request signal
DMAC bus request signal
DRAM interface bus request signal
CPU bus acknowledge signal
DMAC bus acknowledge signal
DRAM interface bus acknowledge signal
BRCR
Bus arbiter
BACK
BREQ
DRAM interface
DRAM control
DRCRA
DRCRB
RTMCSR
RTCNT
Legend
ABWCR
ASTCR
WCRH
WCRL
BRCR
CSCR
DRCRA
DRCRB
RTMCSR
RTCNT
RTCOR
ADRCR
BCR
RTCOR
: Bus width control register
: Access state control register
: Wait control register H
: Wait control register L
: Bus release control register
: Chip select control register
: DRAM control register A
: DRAM control register B
: Refresh timer control/status register
: Refresh timer counter
: Refresh time constant register
: Address control register
: Bus control register
Figure 6.1 Block Diagram of Bus Controller
Rev. 3.00 Sep 14, 2005 page 115 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.1.3
Pin Configuration
Table 6.1 summarizes the input/output pins of the bus controller.
Table 6.1
Bus Controller Pins
Name
Abbreviation
I/O
Function
Output
Strobe signals selecting areas 0 to 7
Output
Strobe signal indicating valid address output
on the address bus
Address strobe
CS0 to CS7
AS
Read
RD
Output
Strobe signal indicating reading from the
external address space
High write
HWR
Output
Strobe signal indicating writing to the
external address space, with valid data on
the upper data bus (D15 to D8)
Low write
LWR
Output
Strobe signal indicating writing to the
external address space, with valid data on
the lower data bus (D7 to D0)
Wait
WAIT
Input
Wait request signal for access to external
three-state access areas
Bus request
BREQ
Input
Request signal for releasing the bus to an
external device
Bus acknowledge
BACK
Output
Acknowledge signal indicating release of the
bus to an external device
Chip select 0 to 7
Rev. 3.00 Sep 14, 2005 page 116 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.1.4
Register Configuration
Table 6.2 summarizes the bus controller's registers.
Table 6.2
Bus Controller Registers
Address*1
Name
Abbreviation
R/W
Initial Value
H'EE020
Bus width control register
ABWCR
R/W
H'FF*2
H'EE021
Access state control register
ASTCR
R/W
H'FF
H'EE022
Wait control register H
WCRH
R/W
H'FF
H'EE023
Wait control register L
WCRL
R/W
H'FF
H'EE013
Bus release control register
BRCR
R/W
H'FE*3
H'EE01F
Chip select control register
CSCR
R/W
H'0F
H'EE01E
Address control register
ADRCR
R/W
H'FF
H'EE024
Bus control register
BCR
R/W
H'C6
H'EE026
DRAM control register A
DRCRA
R/W
H'10
H'EE027
DRAM control register B
DRCRB
R/W
H'08
4
H'EE028
Refresh timer control/status register
RTMCSR
R(W)*
H'07
H'EE029
Refresh timer counter
RTCNT
R/W
H'00
Refresh time constant register
RTCOR
R/W
H'FF
H'EE02A
Notes: 1.
2.
3.
4.
Lower 20 bits of the address in advanced mode.
In modes 2 and 4, the initial value is H'00.
In modes 3 and 4, the initial value is H'EE.
For Bit 7, only 0 can be written to clear the flag.
Rev. 3.00 Sep 14, 2005 page 117 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2
Register Descriptions
6.2.1
Bus Width Control Register (ABWCR)
ABWCR is an 8-bit readable/writable register that selects 8-bit or 16-bit access for each area.
7
Bit
ABW7
Modes
Initial value 1
1, 3, 5, 6,
and 7
Read/Write R/W
Modes
2 and 4
Initial value
0
Read/Write R/W
6
5
4
3
2
1
0
ABW6
ABW5
ABW4
ABW3
ABW2
ABW1
ABW0
1
1
1
1
1
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
When ABWCR contains H'FF (selecting 8-bit access for all areas), the chip operates in 8-bit bus
mode: the upper data bus (D15 to D8) is valid, and port 4 is an input/output port. When at least
one bit is cleared to 0 in ABWCR, the chip operates in 16-bit bus mode with a 16-bit data bus
(D15 to D0). In modes 1, 3, 5, 6, and 7, ABWCR is initialized to H'FF by a reset and in hardware
standby mode. In modes 2 and 4, ABWCR is initialized to H'00 by a reset and in hardware
standby mode. It is not initialized in software standby mode.
Bits 7 to 0—Area 7 to 0 Bus Width Control (ABW7 to ABW0): These bits select 8-bit access
or 16-bit access for the corresponding areas.
Bits 7 to 0
ABW7 to ABW0
Description
0
Areas 7 to 0 are 16-bit access areas
1
Areas 7 to 0 are 8-bit access areas
ABWCR specifies the data bus width of external memory areas. The data bus width of on-chip
memory and registers is fixed, and does not depend on ABWCR settings. These settings are
therefore meaningless in the single-chip modes (modes 6 and 7).
Rev. 3.00 Sep 14, 2005 page 118 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.2
Access State Control Register (ASTCR)
ASTCR is an 8-bit readable/writable register that selects whether each area is accessed in two
states or three states.
7
6
5
4
3
2
1
0
AST7
AST6
AST5
AST4
AST3
AST2
AST1
AST0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
Bit
R/W
R/W
Bits selecting number of states for access to each area
ASTCR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 0—Area 7 to 0 Access State Control (AST7 to AST0): These bits select whether the
corresponding area is accessed in two or three states.
Bits 7 to 0
AST7 to AST0
Description
0
Areas 7 to 0 are accessed in two states
1
Areas 7 to 0 are accessed in three states
(Initial value)
ASTCR specifies the number of states in which external areas are accessed. On-chip memory and
registers are accessed in a fixed number of states that does not depend on ASTCR settings. These
settings are therefore meaningless in the single-chip modes (modes 6 and 7).
When the corresponding area is designated as DRAM space by bits DRAS2 to DRAS0 in DRAM
control register A (DRCRA), the number of access states does not depend on the AST bit setting.
When an AST bit is cleared to 0, programmable wait insertion is not performed.
Rev. 3.00 Sep 14, 2005 page 119 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.3
Wait Control Registers H and L (WCRH, WCRL)
WCRH and WCRL are 8-bit readable/writable registers that select the number of program wait
states for each area.
On-chip memory and registers are accessed in a fixed number of states that does not depend on
WCRH/WCRL settings.
WCRH and WCRL are initialized to H'FF by a reset and in hardware standby mode. They are
not initialized in software standby mode.
WCRH
7
6
5
4
3
2
1
0
W71
W70
W61
W60
W51
W50
W41
W40
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
Bit
R/W
R/W
Bits 7 and 6—Area 7 Wait Control 1 and 0 (W71, W70): These bits select the number of
program wait states when area 7 in external space is accessed while the AST7 bit in ASTCR is set
to 1.
Bit 7
W71
Bit 6
W70
Description
0
0
Program wait not inserted when external space area 7 is accessed
1
1 program wait state inserted when external space area 7 is accessed
0
2 program wait states inserted when external space area 7 is accessed
1
3 program wait states inserted when external space area 7 is accessed
(Initial value)
1
Rev. 3.00 Sep 14, 2005 page 120 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bits 5 and 4—Area 6 Wait Control 1 and 0 (W61, W60): These bits select the number of
program wait states when area 6 in external space is accessed while the AST6 bit in ASTCR is set
to 1.
Bit 5
W61
Bit 4
W60
Description
0
0
Program wait not inserted when external space area 6 is accessed
1
1 program wait state inserted when external space area 6 is accessed
0
2 program wait states inserted when external space area 6 is accessed
1
3 program wait states inserted when external space area 6 is accessed
(Initial value)
1
Bits 3 and 2—Area 5 Wait Control 1 and 0 (W51, W50): These bits select the number of
program wait states when area 5 in external space is accessed while the AST5 bit in ASTCR is set
to 1.
Bit 3
W51
Bit 2
W50
Description
0
0
Program wait not inserted when external space area 5 is accessed
1
1 program wait state inserted when external space area 5 is accessed
0
2 program wait states inserted when external space area 5 is accessed
1
3 program wait states inserted when external space area 5 is accessed
(Initial value)
1
Bits 1 and 0—Area 4 Wait Control 1 and 0 (W41, W40): These bits select the number of
program wait states when area 4 in external space is accessed while the AST4 bit in ASTCR is set
to 1.
Bit 1
W41
Bit 0
W40
Description
0
0
Program wait not inserted when external space area 4 is accessed
1
1 program wait state inserted when external space area 4 is accessed
0
2 program wait states inserted when external space area 4 is accessed
1
3 program wait states inserted when external space area 4 is accessed
(Initial value)
1
Rev. 3.00 Sep 14, 2005 page 121 of 910
REJ09B0258-0300
Section 6 Bus Controller
WCRL
7
6
5
4
3
2
1
0
W31
W30
W21
W20
W11
W10
W01
W00
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
Bit
R/W
R/W
Bits 7 and 6—Area 3 Wait Control 1 and 0 (W31, W30): These bits select the number of
program wait states when area 3 in external space is accessed while the AST3 bit in ASTCR is set
to 1.
Bit 7
W31
Bit 6
W30
Description
0
0
Program wait not inserted when external space area 3 is accessed
1
1 program wait state inserted when external space area 3 is accessed
0
2 program wait states inserted when external space area 3 is accessed
1
3 program wait states inserted when external space area 3 is accessed
(Initial value)
1
Bits 5 and 4—Area 2 Wait Control 1 and 0 (W21, W20): These bits select the number of
program wait states when area 2 in external space is accessed while the AST2 bit in ASTCR is set
to 1.
Bit 5
W21
Bit 4
W20
Description
0
0
Program wait not inserted when external space area 2 is accessed
1
1 program wait state inserted when external space area 2 is accessed
0
2 program wait states inserted when external space area 2 is accessed
1
3 program wait states inserted when external space area 2 is accessed
(Initial value)
1
Rev. 3.00 Sep 14, 2005 page 122 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bits 3 and 2—Area 1 Wait Control 1 and 0 (W11, W10): These bits select the number of
program wait states when area 1 in external space is accessed while the AST1 bit in ASTCR is set
to 1.
Bit 3
W11
Bit 2
W10
Description
0
0
Program wait not inserted when external space area 1 is accessed
1
1 program wait state inserted when external space area 1 is accessed
0
2 program wait states inserted when external space area 1 is accessed
1
3 program wait states inserted when external space area 1 is accessed
(Initial value)
1
Bits 1 and 0—Area 0 Wait Control 1 and 0 (W01, W00): These bits select the number of
program wait states when area 0 in external space is accessed while the AST0 bit in ASTCR is set
to 1.
Bit 1
W01
Bit 0
W00
Description
0
0
Program wait not inserted when external space area 0 is accessed
1
1 program wait state inserted when external space area 0 is accessed
0
2 program wait states inserted when external space area 0 is accessed
1
3 program wait states inserted when external space area 0 is accessed
(Initial value)
1
Rev. 3.00 Sep 14, 2005 page 123 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.4
Bus Release Control Register (BRCR)
BRCR is an 8-bit readable/writable register that enables address output on bus lines A23 to A20
and enables or disables release of the bus to an external device.
Bit
Modes
1, 2, 6,
and 7
7
6
5
4
3
2
1
0
A23E
A22E
A21E
A20E
—
—
—
BRLE
1
1
1
1
1
1
1
0
Read/Write —
—
—
—
—
—
—
R/W
Initial value
Modes Initial value 1
3 and 4 Read/Write R/W
Mode 5
Initial value
1
1
0
1
1
1
0
R/W
R/W
—
—
—
—
R/W
1
1
1
1
1
1
0
R/W
R/W
R/W
—
—
—
R/W
1
Read/Write R/W
Reserved bits
Address 23 to 20 enable
These bits enable PA7 to PA4 to be
used for A23 to A20 address output
Bus release enable
Enables or disables
release of the bus
to an external device
BRCR is initialized to H'FE in modes 1, 2, 5, 6, and 7, and to H'EE in modes 3 and 4, by a reset
and in hardware standby mode. It is not initialized in software standby mode.
Bit 7—Address 23 Enable (A23E): Enables PA4 to be used as the A23 address output pin.
Writing 0 in this bit enables A23 output from PA4. In modes other than 3, 4, and 5, this bit cannot
be modified and PA4 has its ordinary port functions.
Bit 7
A23E
Description
0
PA4 is the A23 address output pin
1
PA4 is an input/output pin
Rev. 3.00 Sep 14, 2005 page 124 of 910
REJ09B0258-0300
(Initial value)
Section 6 Bus Controller
Bit 6—Address 22 Enable (A22E): Enables PA5 to be used as the A22 address output pin.
Writing 0 in this bit enables A22 output from PA5. In modes other than 3, 4, and 5, this bit cannot
be modified and PA5 has its ordinary port functions.
Bit 6
A22E
Description
0
PA5 is the A22 address output pin
1
PA5 is an input/output pin
(Initial value)
Bit 5—Address 21 Enable (A21E): Enables PA6 to be used as the A21 address output pin.
Writing 0 in this bit enables A21 output from PA6. In modes other than 3, 4, and 5, this bit cannot
be modified and PA6 has its ordinary port functions.
Bit 5
A21E
Description
0
PA6 is the A21 address output pin
1
PA6 is an input/output pin
(Initial value)
Bit 4—Address 20 Enable (A20E): Enables PA7 to be used as the A20 address output pin.
Writing 0 in this bit enables A20 output from PA7. This bit can only be modified in mode 5.
Bit 4
A20E
Description
0
PA7 is the A20 address output pin (Initial value when in mode 3 or 4)
1
PA7 is an input/output pin (Initial value when in mode 1, 2, 5, 6, or 7)
Bits 3 to 1—Reserved: These bits cannot be modified and are always read as 1.
Bit 0—Bus Release Enable (BRLE): Enables or disables release of the bus to an external
device.
Bit 0
BRLE
Description
0
The bus cannot be released to an external device
BREQ and BACK can be used as input/output pins
1
The bus can be released to an external device
(Initial value)
Rev. 3.00 Sep 14, 2005 page 125 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.5
Bus Control Register (BCR)
7
6
ICIS1
ICIS0
Initial value
1
1
0
Read/Write
R/W
R/W
R/W
Bit
5
4
3
2
1
0
EMC
RDEA
WAITE
0
1
1
0
R/W
R/W
R/W
BROME BRSTS1 BRSTS0
0
R/W
R/W
BCR is an 8-bit readable/writable register that enables or disables idle cycle insertion, selects the
address map, selects the area division unit, and enables or disables WAIT pin input.
BCR is initialized to H'C6 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bit 7—Idle Cycle Insertion 1 (ICIS1): Selects whether one idle cycle state is to be inserted
between bus cycles in case of consecutive external read cycles for different areas.
Bit 7
ICIS1
Description
0
No idle cycle inserted in case of consecutive external read cycles for different
areas
1
Idle cycle inserted in case of consecutive external read cycles for different
areas
(Initial value)
Bit 6—Idle Cycle Insertion 0 (ICIS0): Selects whether one idle cycle state is to be inserted
between bus cycles in case of consecutive external read and write cycles.
Bit 6
ICIS0
Description
0
No idle cycle inserted in case of consecutive external read and write cycles
1
Idle cycle inserted in case of consecutive external read and write cycles
(Initial value)
Bit 5—Burst ROM Enable (BROME): Selects whether area 0 is a burst ROM interface area.
Bit 5
BROME
Description
0
Area 0 is a basic bus interface area
1
Area 0 is a burst ROM interface area
Rev. 3.00 Sep 14, 2005 page 126 of 910
REJ09B0258-0300
(Initial value)
Section 6 Bus Controller
Bit 4—Burst Cycle Select 1 (BRSTS1): Selects the number of burst cycle states for the burst
ROM interface.
Bit 4
BRSTS1
Description
0
Burst access cycle comprises 2 states
1
Burst access cycle comprises 3 states
(Initial value)
Bit 3—Burst Cycle Select 0 (BRSTS0): Selects the number of words that can be accessed in a
burst ROM interface burst access.
Bit 3
BRSTS0
Description
0
Max. 4 words in burst access (burst access on match of address bits above
A3)
(Initial value)
1
Max. 8 words in burst access (burst access on match of address bits above
A4)
Bit 2—Expansion Memory Map Control (EMC): Selects either of the two memory maps.
Bit 2
EMC
Description
0
Selects the memory map shown in figure 3.2: see section 3.6, Memory Map in
Each Operating Mode
1
Selects the memory map shown in figure 3.1: see section 3.6, Memory Map in
Each Operating Mode
(Initial value)
When EMC is cleared to 0, addresses of some internal I/O registers are moved. For details, refer
to appendix B.2, Address List (when EMC = 0).
This bit is invalid in mode 6. In mode 6 and when the RDEA bit is 0, EMC must not be cleared to
0.
Rev. 3.00 Sep 14, 2005 page 127 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bit 1—Area Division Unit Select (RDEA): Selects the memory map area division units. This bit
is valid in modes 3, 4, and 5, and is invalid in modes 1, 2, 6, and 7.
When the EMC bit is 0, RDEA must not be cleared to 0.
Bit 1
RDEA
Description
0
Area divisions are as follows:
1
Area 0: 2 Mbytes
Area 4: 1.93 Mbytes
Area 1: 2 Mbytes
Area 5: 4 kbytes
Area 2: 8 Mbytes
Area 6: 23.75 kbytes
Area 3: 2 Mbytes
Area 7: 22 bytes
Areas 0 to 7 are the same size (2 Mbytes)
(Initial value)
Bit 0—WAIT Pin Enable (WAITE): Enables or disables wait insertion by means of the WAIT
pin.
Bit 0
WAITE
Description
0
WAIT pin wait input is disabled, and the WAIT pin can be used as an
input/output port
1
WAIT pin wait input is enabled
Rev. 3.00 Sep 14, 2005 page 128 of 910
REJ09B0258-0300
(Initial value)
Section 6 Bus Controller
6.2.6
Chip Select Control Register (CSCR)
CSCR is an 8-bit readable/writable register that enables or disables output of chip select signals
(CS7 to CS4).
If output of a chip select signal is enabled by a setting in this register, the corresponding pin
functions as a chip select signal (CS7 to CS4) output regardless of any other settings. CSCR
cannot be modified in single-chip mode.
Bit
7
6
5
4
3
2
1
0
CS7E
CS6E
CS5E
CS4E
—
—
—
—
Initial value
0
0
0
0
1
1
1
1
Read/Write
R/W
R/W
R/W
—
—
—
—
R/W
Reserved bits
Chip select 7 to 4 enable
These bits enable or disable
chip select signal output
CSCR is initialized to H'0F by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 4—Chip Select 7 to 4 Enable (CS7E to CS4E): These bits enable or disable output of
the corresponding chip select signal.
Bit n
CSnE
Description
0
Output of chip select signal
1
CSn is disabled
Output of chip select signal CSn is enabled
(Initial value)
Note: n = 7 to 4
Bits 3 to 0—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 129 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.7
DRAM Control Register A (DRCRA)
7
6
5
4
3
2
1
0
DRAS2
DRAS1
DRAS0
—
BE
RDM
SRFMD
RFSHE
Initial value
0
0
0
1
0
0
0
0
Read/Write
R/W
R/W
R/W
—
R/W
R/W
R/W
Bit
R/W
DRCRA is an 8-bit readable/writable register that selects the areas that have a DRAM interface
function, and the access mode, and enables or disables self-refreshing and refresh pin output.
DRCRA is initialized to H'10 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 5—DRAM Area Select (DRAS2 to DRAS0): These bits select which of areas 2 to 5
are to function as DRAM interface areas (DRAM space) in expanded mode, and at the same time
select the RAS output pin corresponding to each DRAM space.
Description
Bit 7
Bit 6
Bit 5
DRAS2 DRAS1 DRAS0 Area 5
Area 4
Area 3
Area 2
0
0
1
1
0
1
0
Normal
Normal
Normal
Normal
1
Normal
Normal
Normal
DRAM space
(CS2)
0
Normal
Normal
DRAM space
(CS3)
DRAM space
(CS2)
1
Normal
Normal
DRAM space
(CS2)*
DRAM space
(CS2)*
0
Normal
DRAM space
(CS4)
DRAM space
(CS3)
DRAM space
(CS2)
1
DRAM space
(CS5)
DRAM space
(CS4)
DRAM space
(CS3)
DRAM space
(CS2)
0
DRAM space
(CS4)*
DRAM space
(CS4)*
DRAM space
(CS2)*
DRAM space
(CS2)*
1
DRAM space
(CS2)*
DRAM space
(CS2)*
DRAM space
(CS2)*
DRAM space
(CS2)*
Note: * A single CSn pin serves as a common RAS output pin for a number of areas. Unused CSn
pins can be used as input/output ports.
Rev. 3.00 Sep 14, 2005 page 130 of 910
REJ09B0258-0300
Section 6 Bus Controller
When any of bits DRAS2 to DRAS0 is set to 1 in expanded mode, it is not possible to write to
DRCRB, RTMCSR, RTCNT, or RTCOR. However, 0 can be written to the CMF flag in
RTMCSR to clear the flag.
When an arbitrary value has been set in DRAS2 to DRAS0, a write of a different value other than
000 must not be performed.
Bit 4—Reserved: This bit cannot be modified and is always read as 1.
Bit 3—Burst Access Enable (BE): Enables or disables burst access to DRAM space. DRAM
space burst access is performed in fast page mode.
Bit 3
BE
Description
0
Burst disabled (always full access)
1
DRAM space access performed in fast page mode
(Initial value)
Bit 2—RAS Down Mode (RDM): Selects whether to wait for the next DRAM access with the
RAS signal held low (RAS down mode), or to drive the RAS signal high again (RAS up mode),
when burst access is enabled for DRAM space (BE = 1), and access to DRAM is interrupted.
Caution is required when the HWR and LWR are used as the UCAS and LCAS output pins. For
details, see RAS Down Mode and RAS Up Mode in section 6.5.10, Burst Operation.
Bit 2
RDM
Description
0
DRAM interface: RAS up mode selected
1
DRAM interface: RAS down mode selected
(Initial value)
Rev. 3.00 Sep 14, 2005 page 131 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bit 1—Self-Refresh Mode (SRFMD): Specifies DRAM self-refreshing in software standby
mode.
When any of areas 2 to 5 is designated as DRAM space, DRAM self-refreshing is possible when a
transition is made to software standby mode after the SRFMD bit has been set to 1.
The normal access state is restored when software standby mode is exited, regardless of the
SRFMD setting.
Bit 1
SRFMD
Description
0
DRAM self-refreshing disabled in software standby mode
1
DRAM self-refreshing enabled in software standby mode
(Initial value)
Bit 0—Refresh Pin Enable (RFSHE): Enables or disables RFSH pin refresh signal output. If
areas 2 to 5 are not designated as DRAM space, this bit should not be set to 1.
Bit 0
RFSHE
Description
RFSH pin refresh signal output disabled
(RFSH pin can be used as input/output port)
RFSH pin refresh signal output enabled
0
1
6.2.8
(Initial value)
DRAM Control Register B (DRCRB)
7
6
5
4
3
2
1
0
MXC1
MXC0
CSEL
RCYCE
—
TPC
RCW
RLW
Initial value
0
0
0
0
1
0
0
0
Read/Write
R/W
R/W
R/W
—
R/W
R/W
Bit
R/W
R/W
DRCRB is an 8-bit readable/writable register that selects the number of address multiplex column
address bits for the DRAM interface, the column address strobe output pin, enabling or disabling
of refresh cycle insertion, the number of precharge cycles, enabling or disabling of wait state
insertion between RAS and CAS, and enabling or disabling of wait state insertion in refresh
cycles.
DRCRB is initialized to H'08 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Rev. 3.00 Sep 14, 2005 page 132 of 910
REJ09B0258-0300
Section 6 Bus Controller
The settings in this register are invalid when bits DRAS2 to DRAS0 in DRCRA are all 0.
Bits 7 and 6—Multiplex Control 1 and 0 (MXC1, MXC0): These bits select the row
address/column address multiplexing method used on the DRAM interface. In burst operation,
the row address used for comparison is determined by the setting of these bits and the bus width
of the relevant area set in ABWCR.
Bit 7
MXC1
Bit 6
MXC0
Description
0
0
Column address: 8 bits
Compared address:
Modes 1, 2
Modes 3, 4, 5
1
8-bit access space
A19 to A8
16-bit access space
A19 to A9
8-bit access space
A23 to A8
16-bit access space
A23 to A9
8-bit access space
A19 to A9
16-bit access space
A19 to A10
8-bit access space
A23 to A9
16-bit access space
A23 to A10
8-bit access space
A19 to A10
16-bit access space
A19 to A11
8-bit access space
A23 to A10
16-bit access space
A23 to A11
Column address: 9 bits
Compared address:
Modes 1, 2
Modes 3, 4, 5
1
0
Column address: 10 bits
Compared address:
Modes 1, 2
Modes 3, 4, 5
1
Illegal setting
Bit 5—CAS Output Pin Select (CSEL): Selects the UCAS and LCAS output pins when areas 2
to 5 are designated as DRAM space.
Bit 5
CSEL
0
1
Description
PB4 and PB5 selected as UCAS and LCAS output pins
HWR and LWR selected as UCAS and LCAS output pins
(Initial value)
Rev. 3.00 Sep 14, 2005 page 133 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bit 4—Refresh Cycle Enable (RCYCE): Enables or disables CAS-before-RAS refresh cycle
insertion. When none of areas 2 to 5 has been designated as DRAM space, refresh cycles are not
inserted regardless of the setting of this bit.
Bit 4
RCYCE
Description
0
Refresh cycles disabled
1
DRAM refresh cycles enabled
(Initial value)
Bit 3—Reserved: This bit cannot be modified and is always read as 1.
Bit 2—TP Cycle Control (TPC): Selects whether a 1-state or two-state precharge cycle (TP) is
to be used for DRAM read/write cycles and CAS-before-RAS refresh cycles.
The setting of this bit does not affect the self-refresh function.
Bit 2
TPC
Description
0
1-state precharge cycle inserted
1
2-state precharge cycle inserted
(Initial value)
Bit 1—RAS-CAS Wait (RCW): Controls wait state (Trw) insertion between Tr and Tc1 in
DRAM read/write cycles. The setting of this bit does not affect refresh cycles.
Bit 1
RCW
Description
0
Wait state (Trw) insertion disabled
1
One wait state (Trw) inserted
(Initial value)
Bit 0—Refresh Cycle Wait Control (RLW): Controls wait state (TRW) insertion for CASbefore-RAS refresh cycles. The setting of this bit does not affect DRAM read/write cycles.
Bit 0
RLW
Description
0
Wait state (TRW ) insertion disabled
1
One wait state (TRW ) inserted
Rev. 3.00 Sep 14, 2005 page 134 of 910
REJ09B0258-0300
(Initial value)
Section 6 Bus Controller
6.2.9
Refresh Timer Control/Status Register (RTMCSR)
7
6
5
4
3
2
1
0
CMF
CMIE
CKS2
CKS1
CKS0
—
—
—
Initial value
0
0
0
0
0
1
1
1
Read/Write
R(W)*
R/W
R/W
R/W
—
—
—
Bit
R/W
RTMCSR is an 8-bit readable/writable register that selects the refresh timer counter clock. When
the refresh timer is used as an interval timer, RTMCSR also enables or disables interrupt requests.
Bits 7 and 6 of RTMCSR are initialized to 0 by a reset and in the standby modes. Bits 5 to 3 are
initialized to 0 by a reset and in hardware standby mode; they are not initialized in software
standby mode.
Note: * Only 0 can be written to clear the flag.
Bit 7—Compare Match Flag (CMF): Status flag that indicates a match between the values of
RTCNT and RTCOR.
Bit 7
CMF
0
1
Description
Clearing conditions
When the chip is reset and in standby mode
Read CMF when CMF = 1, then write 0 in CMF
(Initial value)
Setting condition
When RTCNT = RTCOR
Bit 6—Compare Match Interrupt Enable (CMIE): Enables or disables the CMI interrupt
requested when the CMF flag is set to 1 in RTMCSR. The CMIE bit is always cleared to 0 when
any of areas 2 to 5 is designated as DRAM space.
Bit 6
CMIE
Description
0
The CMI interrupt requested by CMF is disabled
1
The CMI interrupt requested by CMF is enabled
(Initial value)
Rev. 3.00 Sep 14, 2005 page 135 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bits 5 to 3—Refresh Counter Clock Select (CKS2 to CKS0): These bits select the clock to be
input to RTCNT from among 7 clocks obtained by dividing the system clock (φ). When the input
clock is selected with bits CKS2 to CKS0, RTCNT begins counting up.
Bit 5 Bit 4 Bit 3
CKS2 CKS1 CKS0 Description
0
0
1
1
0
1
0
Count operation halted
1
φ/2 used as counter clock
(Initial value)
0
φ/8 used as counter clock
1
φ/32 used as counter clock
0
φ/128 used as counter clock
1
φ/512 used as counter clock
0
φ/2048 used as counter clock
1
φ/4096 used as counter clock
Bits 2 to 0—Reserved: These bits cannot be modified and are always read as 1.
6.2.10
Refresh Timer Counter (RTCNT)
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RTCNT is an 8-bit readable/writable up-counter.
RTCNT is incremented by an internal clock selected by bits CKS2 to CKS0 in RTMCSR. When
RTCNT matches RTCOR (compare match), the CMF flag in RTMCSR is set to 1 and RTCNT is
cleared to H'00. If the RCYCE bit in DRCRB is set to 1 at this time, a refresh cycle is started.
Also, if the CMIE bit in RTMCSR is set to 1, a compare match interrupt (CMI) is generated.
RTCNT is initialized to H'00 by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 136 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.11
Refresh Time Constant Register (RTCOR)
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RTCOR is an 8-bit readable/writable register that determines the interval at which RTCNT is
cleared.
RTCOR and RTCNT are constantly compared. When their values match, the CMF flag is set to 1
in RTMCSR, and RTCNT is simultaneously cleared to H'00.
RTCOR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Note: Only byte access can be used on this register.
Rev. 3.00 Sep 14, 2005 page 137 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.2.12
Address Control Register (ADRCR)
ADRCR is an 8-bit readable/writable register that selects either address update mode 1 or address
update mode 2 as the address output method.
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
ADRCTL
Initial value
1
1
1
1
1
1
1
1
R/W
—
—
—
—
—
—
—
R/W
Bit
Reserved bits
Address control
Selects address update
mode 1 or address
update mode 2
ADRCR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 2—Reserved: These bits cannot be modified and are always read as 1.
Bit 1—Reserved: This bit is always read as 1. Do not write 0 to this bit.
Bit 0—Address Control (ADRCTL): Selects the address output method.
Bit 0
ADRCTL
Description
0
Address update mode 2 is selected
1
Address update mode 1 is selected
Rev. 3.00 Sep 14, 2005 page 138 of 910
REJ09B0258-0300
(Initial value)
Section 6 Bus Controller
6.3
Operation
6.3.1
Area Division
The external address space is divided into areas 0 to 7. Each area has a size of 128 kbytes in the
1-Mbyte modes, or 2-Mbytes in the 16-Mbyte modes. Figure 6.2 shows a general view of the
memory map.
H' 00000
H' 000000
Area 0 (128 kbytes)
H' 1FFFF
Area 0 (2 Mbytes)
H' 1FFFFF
H' 20000
H' 200000
Area 1 (128 kbytes)
H' 3FFFF
Area 1 (2 Mbytes)
H' 3FFFFF
H' 40000
H' 400000
Area 2 (128 kbytes)
H' 5FFFF
Area 2 (2 Mbytes)
H' 5FFFFF
H' 60000
H' 600000
Area 3 (128 kbytes)
H' 7FFFF
Area 3 (2 Mbytes)
H' 7FFFFF
H' 80000
H' 800000
Area 4 (128 kbytes)
H' 9FFFF
Area 4 (2 Mbytes)
H' 9FFFFF
H' A0000
H' A00000
Area 5 (128 kbytes)
H' BFFFF
H' C0000
H' DFFFF
Area 5 (2 Mbytes)
H' BFFFFF
H' C00000
Area 6 (128 kbytes)
H' E0000
H' DFFFFF
Area 6 (2 Mbytes)
H' E00000
Area 7 (128 kbytes)
Area 7 (2 Mbytes)
H' FFFFF
H' FFFFFF
(a) 1-Mbyte modes (modes 1, and 2)
(b) 16-Mbyte modes (modes 3, 4, and 5)
Figure 6.2 Access Area Map for Each Operating Mode
Chip select signals (CS0 to CS7) can be output for areas 0 to 7. The bus specifications for each
area are selected in ABWCR, ASTCR, WCRH, and WCRL.
In 16-Mbyte mode, the area division units can be selected with the RDEA bit in BCR.
Rev. 3.00 Sep 14, 2005 page 139 of 910
REJ09B0258-0300
Section 6 Bus Controller
Area 0
2 Mbytes
Area 0
2 Mbytes
Area 1
2 Mbytes
Area 1
2 Mbytes
2 Mbytes
H'000000
2 Mbytes
H'1FFFFF
H'200000
Area 2
2 Mbytes
H'5FFFFF
2 Mbytes
H'3FFFFF
H'400000
Area 2
8 Mbytes
2 Mbytes
H'600000
Area 3
2 Mbytes
2 Mbytes
H'7FFFFF
H'800000
Area 4
2 Mbytes
2 Mbytes
H'9FFFFF
H'A00000
Area 5
2 Mbytes
Area 6
2 Mbytes
Area 3
2 Mbytes
Area 7
1.93 Mbytes
Area 4
1.93 Mbytes
On-chip registers (1)
On-chip registers (1)
2 Mbytes
H'BFFFFF
H'C00000
H'DFFFFF
H'E00000
H'FEE000
H'FEE0FF
H'FEE100
Reserved 39.75 kbytes
H'FF7FFF
H'FF8000
Area 6
23.75 kbytes
On-chip RAM
4 kbytes
On-chip RAM
4 kbytes*
On-chip registers (2)
On-chip registers (2)
Area 7
22 bytes
Area 7
22 bytes
(A) Memory map when RDEA = 1
(b) Memory map when RDEA = 0
H'FFEF1F
H'FFEF20
H'FFFF1F
H'FFFF20
H'FFFFE9
H'FFFFEA
H'FFFFFF
Note: * Area 6 when the RAME bit is cleared.
Figure 6.3 Memory Map in 16-Mbyte Mode
Rev. 3.00 Sep 14, 2005 page 140 of 910
REJ09B0258-0300
Absolute
address 8 bits
H'FFFEFF
H'FFFF00
2 Mbytes
Area 7
67.5 kbytes
Absolute
address 16 bits
Area 5
4 kbytes
H'FF8FFF
H'FF9000
Section 6 Bus Controller
6.3.2
Bus Specifications
The external space bus specifications consist of three elements: (1) bus width, (2) number of
access states, and (3) number of program wait states.
The bus width and number of access states for on-chip memory and registers are fixed, and are
not affected by the bus controller.
Bus Width: A bus width of 8 or 16 bits can be selected with ABWCR. An area for which an 8bit bus is selected functions as an 8-bit access space, and an area for which a 16-bit bus is
selected functions as a16-bit access space.
If all areas are designated for 8-bit access, 8-bit bus mode is set; if any area is designated for 16bit access, 16-bit bus mode is set.
Number of Access States: Two or three access states can be selected with ASTCR. An area for
which two-state access is selected functions as a two-state access space, and an area for which
three-state access is selected functions as a three-state access space.
DRAM space is accessed in four states regardless of the ASTCR settings.
When two-state access space is designated, wait insertion is disabled.
Number of Program Wait States: When three-state access space is designated in ASTCR, the
number of program wait states to be inserted automatically is selected with WCRH and WCRL.
From 0 to 3 program wait states can be selected.
When ASTCR is cleared to 0 for DRAM space, a program wait (Tc1-Tc2 wait) is not inserted.
Also, no program wait is inserted in burst ROM space burst cycles.
Table 6.3 shows the bus specifications for each basic bus interface area.
Rev. 3.00 Sep 14, 2005 page 141 of 910
REJ09B0258-0300
Section 6 Bus Controller
Table 6.3
Bus Specifications for Each Area (Basic Bus Interface)
ABWCR ASTCR WCRH/WCRL
Bus Specifications (Basic Bus Interface)
ABWn
ASTn
Wn1
Wn0
Bus Width
Access States
Program Wait States
0
0
—
—
16
2
0
1
0
0
3
0
1
1
1
1
0
2
1
3
0
—
—
1
0
0
1
8
2
0
3
0
1
1
0
2
1
3
Note: n = 7 to 0
6.3.3
Memory Interfaces
The H8/3068F memory interfaces comprise a basic bus interface that allows direct connection of
ROM, SRAM, and so on; a DRAM interface that allows direct connection of DRAM; and a burst
ROM interface that allows direct connection of burst ROM. The interface can be selected
independently for each area.
An area for which the basic bus interface is designated functions as normal space, an area for
which the DRAM interface is designated functions as DRAM space, and area 0 for which the
burst ROM interface is designated functions as burst ROM space.
Rev. 3.00 Sep 14, 2005 page 142 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.3.4
Chip Select Signals
For each of areas 0 to 7, the H8/3068F can output a chip select signal (CS0 to CS7) that goes low
when the corresponding area is selected in expanded mode. Figure 6.4 shows the output timing of
a CSn signal.
Output of CS0 to CS3: Output of CS0 to CS3 is enabled or disabled in the data direction register
(DDR) of the corresponding port.
In the expanded modes with on-chip ROM disabled, a reset leaves pin CS0 in the output state and
pins CS1 to CS3 in the input state. To output chip select signals CS1 to CS3, the corresponding
DDR bits must be set to 1. In the expanded modes with on-chip ROM enabled, a reset leaves pins
CS0 to CS3 in the input state. To output chip select signals CS0 to CS3, the corresponding DDR
bits must be set to 1. For details, see section 8, I/O Ports.
Output of CS4 to CS7: Output of CS4 to CS7 is enabled or disabled in the chip select control
register (CSCR). A reset leaves pins CS4 to CS7 in the input state. To output chip select signals
CS4 to CS7, the corresponding CSCR bits must be set to 1. For details, see section 8, I/O Ports.
φ
Address
External address in area n
CSn
Figure 6.4
CSn Signal Output Timing (n = 0 to 7)
When the on-chip ROM, on-chip RAM, and on-chip registers are accessed, CS0 to CS7 remain
high. The CSn signals are decoded from the address signals. They can be used as chip select
signals for SRAM and other devices.
Rev. 3.00 Sep 14, 2005 page 143 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.3.5
Address Output Method
The H8/3068F provides a choice of two address update methods: either the same method as in the
previous H8/300H Series (address update mode 1), or a method in which address update is
restricted to external space accesses or self-refresh cycles (address update mode 2).
Figure 6.5 shows examples of address output in these two update modes.
On-chip
memory cycle
External
read cycle
On-chip
memory cycle
External
read cycle
On-chip
memory cycle
Address update
mode 1
Address update
mode 2
RD
Figure 6.5 Sample Address Output in Each Address Update Mode
(Basic Bus Interface, 3-State Space)
Address Update Mode 1: Address update mode 1 is compatible with the previous H8/300H
Series. Addresses are always updated between bus cycles.
Address Update Mode 2: In address update mode 2, address updating is performed only in
external space accesses or self-refresh cycles. In this mode, the address can be retained between
an external space read cycle and an instruction fetch cycle (on-chip memory) by placing the
program in on-chip memory. Address update mode 2 is therefore useful when connecting a
device that requires address hold time with respect to the rise of the RD strobe.
Switching between address update modes 1 and 2 is performed by means of the ADRCTL bit in
ADRCR. The initial value of ADRCR is the address update mode 1 setting, providing
compatibility with the previous H8/300H Series.
Rev. 3.00 Sep 14, 2005 page 144 of 910
REJ09B0258-0300
Section 6 Bus Controller
Cautions: When using address update modes, the following points should be noted.
• When address update mode 2 is selected, the address in an internal space (on-chip memory or
internal I/O) access cycle is not output externally.
• In order to secure address holding with respect to the rise of RD, when address update mode 2
is used an external space read access must be completed within a single access cycle. For
example, in a word access to 8-bit access space, the bus cycle is split into two as shown in
figure 6.6., and so there is not a single access cycle. In this case, address holding is not
guaranteed at the rise of RD between the first (even address) and second (odd address) access
cycles (area inside the ellipse in the figure).
On-chip
memory cycle
Address update
mode 2
External read cycle
(8-bit space word access)
Even address
On-chip
memory cycle
Odd address
RD
Figure 6.6 Example of Consecutive External Space Accesses in Address Update Mode 2
• When address update mode 2 is selected, in a DRAM space CAS-before-RAS (CBR) refresh
cycle the previous address is retained (the area 2 start address is not output).
Rev. 3.00 Sep 14, 2005 page 145 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.4
Basic Bus Interface
6.4.1
Overview
The basic bus interface enables direct connection of ROM, SRAM, and so on.
The bus specifications can be selected with ABWCR, ASTCR, WCRH, and WCRL
(see table 6.3).
6.4.2
Data Size and Data Alignment
Data sizes for the CPU and other internal bus masters are byte, word, and longword. The bus
controller has a data alignment function, and when accessing external space, controls whether the
upper data bus (D15 to D8) or lower data bus (D7 to D0) is used according to the bus specifications
for the area being accessed (8-bit access area or 16-bit access area) and the data size.
8-Bit Access Areas: Figure 6.7 illustrates data alignment control for 8-bit access space. With 8bit access space, the upper data bus (D15 to D8) is always used for accesses. The amount of data
that can be accessed at one time is one byte: a word access is performed as two byte accesses, and
a longword access, as four byte accesses.
Upper data bus
Lower data bus
D15
D8 D7
D0
Byte size
Word size
1st bus cycle
2nd bus cycle
1st bus cycle
Longword size
2nd bus cycle
3rd bus cycle
4th bus cycle
Figure 6.7 Access Sizes and Data Alignment Control (8-Bit Access Area)
16-Bit Access Areas: Figure 6.8 illustrates data alignment control for 16-bit access areas. With
16-bit access areas, the upper data bus (D15 to D8) and lower data bus (D7 to D0) are used for
accesses. The amount of data that can be accessed at one time is one byte or one word, and a
longword access is executed as two word accesses.
Rev. 3.00 Sep 14, 2005 page 146 of 910
REJ09B0258-0300
Section 6 Bus Controller
In byte access, whether the upper or lower data bus is used is determined by whether the address
is even or odd. The upper data bus is used for an even address, and the lower data bus for an
odd address.
Upper data bus
Lower data bus
D15
D8 D7
D0
Byte size
· Even address
Byte size
· Odd address
Word size
Longword size
1st bus cycle
2nd bus cycle
Figure 6.8 Access Sizes and Data Alignment Control (16-Bit Access Area)
6.4.3
Valid Strobes
Table 6.4 shows the data buses used, and the valid strobes, for the access spaces.
In a read, the RD signal is valid for both the upper and the lower half of the data bus.
In a write, the HWR signal is valid for the upper half of the data bus, and the LWR signal for the
lower half.
Rev. 3.00 Sep 14, 2005 page 147 of 910
REJ09B0258-0300
Section 6 Bus Controller
Table 6.4
Data Buses Used and Valid Strobes
Access
Size
Read/Write
Address
8-bit
access
area
Byte
Read
—
Write
—
RD
HWR
16-bit
access
Byte
Read
Even
RD
Area
Valid Strobe
Odd
area
Write
Word
Even
HWR
Odd
LWR
Read
—
Write
—
RD
HWR, LWR
Upper Data Bus Lower Data Bus
(D15 to D8)
(D7 to D0)
Valid
Invalid
Undetermined
data
Valid
Invalid
Invalid
Valid
Valid
Undetermined
data
Undetermined
data
Valid
Valid
Valid
Valid
Valid
Notes: 1. Undetermined data means that unpredictable data is output.
2. Invalid means that the bus is in the input state and the input is ignored.
6.4.4
Memory Areas
The initial state of each area is basic bus interface, three-state access space. The initial bus width
is selected according to the operating mode. The bus specifications described here cover basic
items only, and the following sections should be referred to for further details: 6.4, Basic Bus
Interface, 6.5, DRAM Interface, 6.8, Burst ROM Interface.
Area 0: Area 0 includes on-chip ROM, and in ROM-disabled expansion mode, all of area 0 is
external space. In ROM-enabled expansion mode, the space excluding on-chip ROM is external
space.
When area 0 external space is accessed, the CS0 signal can be output.
Either basic bus interface or burst ROM interface can be selected for area 0.
The size of area 0 is 128 kbytes in modes 1 and 2, and 2 Mbytes in modes 3, 4, and 5.
Areas 1 and 6: In external expansion mode, areas 1 and 6 are entirely external space.
When area 1 and 6 external space is accessed, the CS1 and CS6 pin signals respectively can be
output.
Only the basic bus interface can be used for areas 1 and 6.
The size of areas 1 and 6 is 128 kbytes in modes 1 and 2, and 2 Mbytes in modes 3, 4, and 5.
Rev. 3.00 Sep 14, 2005 page 148 of 910
REJ09B0258-0300
Section 6 Bus Controller
Areas 2 to 5: In external expansion mode, areas 2 to 5 are entirely external space.
When area 2 to 5 external space is accessed, signals CS2 to CS5 can be output.
Basic bus interface or DRAM interface can be selected for areas 2 to 5. With the DRAM
interface, signals CS2 to CS5 are used as RAS signals.
The size of areas 2 to 5 is 128 kbytes in modes 1 and 2, and 2 Mbytes in modes 3, 4, and 5.
Area 7: Area 7 includes the on-chip RAM and registers. In external expansion mode, the space
excluding the on-chip RAM and registers is external space. The on-chip RAM is enabled when
the RAME bit in the system control register (SYSCR) is set to 1; when the RAME bit is cleared to
0, the on-chip RAM is disabled and the corresponding space becomes external space .
When area 7 external space is accessed, the CS7 signal can be output.
Only the basic bus interface can be used for the area 7 memory interface.
The size of area 7 is 128 kbytes in modes 1 and 2, and 2 Mbytes in modes 3, 4, and 5.
Rev. 3.00 Sep 14, 2005 page 149 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.4.5
Basic Bus Control Signal Timing
8-Bit, Three-State-Access Areas
Figure 6.9 shows the timing of bus control signals for an 8-bit, three-state-access area. The upper
data bus (D15 to D8) is used in accesses to these areas. The LWR pin is always high. Wait states
can be inserted.
Bus cycle
T1
T2
T3
φ
Address bus
External address in area n
CSn
AS
RD
Read access
D15 to D8
Valid
D7 to D0
Invalid
HWR
LWR
High
Write access
D15 to D8
D7 to D0
Valid
Undetermined data
Note: n = 7 to 0
Figure 6.9 Bus Control Signal Timing for 8-Bit, Three-State-Access Area
Rev. 3.00 Sep 14, 2005 page 150 of 910
REJ09B0258-0300
Section 6 Bus Controller
8-Bit, Two-State-Access Areas
Figure 6.10 shows the timing of bus control signals for an 8-bit, two-state-access area. The upper
data bus (D15 to D8) is used in accesses to these areas. The LWR pin is always high. Wait states
cannot be inserted.
Bus cycle
T2
T1
φ
Address bus
External address in area n
CSn
AS
RD
Read access
D15 to D8
Valid
D7 to D0
Invalid
HWR
LWR
High
Write access
D15 to D8
Valid
D7 to D0
Undetermined data
Note: n = 7 to 0
Figure 6.10 Bus Control Signal Timing for 8-Bit, Two-State-Access Area
Rev. 3.00 Sep 14, 2005 page 151 of 910
REJ09B0258-0300
Section 6 Bus Controller
16-Bit, Three-State-Access Areas
Figures 6.11 to 6.13 show the timing of bus control signals for a 16-bit, three-state-access area.
In these areas, the upper data bus (D15 to D8) is used in accesses to even addresses and the lower
data bus (D7 to D0) in accesses to odd addresses. Wait states can be inserted.
Bus cycle
T1
T2
T3
φ
Address bus
Even external address in area n
CSn
AS
RD
Read access
D15 to D8
Valid
D7 to D0
Invalid
HWR
LWR
High
Write access
D15 to D8
Valid
D7 to D0
Undetermined data
Note: n = 7 to 0
Figure 6.11 Bus Control Signal Timing for 16-Bit, Three-State-Access Area (1)
(Byte Access to Even Address)
Rev. 3.00 Sep 14, 2005 page 152 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bus cycle
T1
T2
T3
φ
Address bus
Odd external address in area n
CSn
AS
RD
Read access
D15 to D8
Invalid
D7 to D0
Valid
HWR
High
LWR
Write access
D15 to D8
Undetermined data
D7 to D0
Valid
Note: n = 7 to 0
Figure 6.12 Bus Control Signal Timing for 16-Bit, Three-State-Access Area (2)
(Byte Access to Odd Address)
Rev. 3.00 Sep 14, 2005 page 153 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bus cycle
T1
T2
T3
φ
Address bus
External address in area n
CSn
AS
RD
Read access
D15 to D8
Valid
D7 to D0
Valid
HWR
LWR
Write access
D15 to D8
Valid
D7 to D0
Valid
Note: n = 7 to 0
Figure 6.13 Bus Control Signal Timing for 16-Bit, Three-State-Access Area (3)
(Word Access)
Rev. 3.00 Sep 14, 2005 page 154 of 910
REJ09B0258-0300
Section 6 Bus Controller
16-Bit, Two-State-Access Areas: Figures 6.14 to 6.16 show the timing of bus control signals for
a 16-bit, two-state-access area. In these areas, the upper data bus (D15 to D8) is used in accesses
to even addresses and the lower data bus (D7 to D0) in accesses to odd addresses. Wait states
cannot be inserted.
Bus cycle
T1
T2
φ
Address bus
Even external address in area n
CSn
AS
RD
Read access
D15 to D8
Valid
D7 to D0
Invalid
HWR
LWR
High
Write access
D15 to D8
Valid
D7 to D0
Undetermined data
Note: n = 7 to 0
Figure 6.14 Bus Control Signal Timing for 16-Bit, Two-State-Access Area (1)
(Byte Access to Even Address)
Rev. 3.00 Sep 14, 2005 page 155 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bus cycle
T1
T2
φ
Address bus
Odd external address in area n
CSn
AS
RD
Read access
D15 to D8
Invalid
D7 to D0
Valid
HWR
High
LWR
Write access
D15 to D8
Undetermined data
D7 to D0
Valid
Note: n = 7 to 0
Figure 6.15 Bus Control Signal Timing for 16-Bit, Two-State-Access Area (2)
(Byte Access to Odd Address)
Rev. 3.00 Sep 14, 2005 page 156 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bus cycle
T1
T2
φ
Address bus
External address in area n
CSn
AS
RD
Read access
D15 to D8
Valid
D7 to D0
Valid
HWR
LWR
Write access
D15 to D8
Valid
D7 to D0
Valid
Note: n = 7 to 0
Figure 6.16 Bus Control Signal Timing for 16-Bit, Two-State-Access Area (3)
(Word Access)
6.4.6
Wait Control
When accessing external space, the H8/3068F can extend the bus cycle by inserting one or more
wait states (Tw). There are two ways of inserting wait states: (1) program wait insertion and (2)
pin wait insertion using the WAIT pin.
Program Wait Insertion: From 0 to 3 wait states can be inserted automatically between the T2
state and T3 state on an individual area basis in three-state access space, according to the settings
of WCRH and WCRL.
Rev. 3.00 Sep 14, 2005 page 157 of 910
REJ09B0258-0300
Section 6 Bus Controller
Pin Wait Insertion: Setting the WAITE bit in BCR to 1 enables wait insertion by means of the
WAIT pin. When external space is accessed in this state, a program wait is first inserted. If the
WAIT pin is low at the falling edge of φ in the last T2 or TW state, another TW state is inserted. If
the WAIT pin is held low, TW states are inserted until it goes high.
This is useful when inserting four or more TW states, or when changing the number of TW states
for different external devices.
The WAITE bit setting applies to all areas. Pin waits cannot be inserted in DRAM space.
Figure 6.17 shows an example of the timing for insertion of one program wait state in 3-state
space.
T1
Inserted
by program wait Inserted by WAIT pin
T2
Tw
Tw
Tw
T3
φ
WAIT
Address bus
AS
RD
Read access
Data bus
Read data
HWR, LWR
Write access
Data bus
Note:
Write data
indicates the timing of WAIT pin sampling.
Figure 6.17 Example of Wait State Insertion Timing
Rev. 3.00 Sep 14, 2005 page 158 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.5
DRAM Interface
6.5.1
Overview
The H8/3068F is provided with a DRAM interface with functions for DRAM control signal
(RAS, UCAS, LCAS, WE) output, address multiplexing, and refreshing, that direct connection of
DRAM. In the expanded modes, external address space areas 2 to 5 can be designated as DRAM
space accessed via the DRAM interface. A data bus width of 8 or 16 bits can be selected for
DRAM space by means of a setting in ABWCR. When a 16-bit data bus width is selected, CAS is
used for byte access control. In the case of × 16-bit organization DRAM, therefore, the 2-CAS
type can be connected. A fast page mode is supported in addition to the normal read and write
access modes.
6.5.2
DRAM Space and RAS Output Pin Settings
Designation of areas 2 to 5 as DRAM space, and selection of the RAS output pin for each area
designated as DRAM space, is performed by setting bits in DRCRA. Table 6.5 shows the
correspondence between the settings of bits DRAS2 to DRAS0 and the selected DRAM space and
RAS output pin.
When an arbitrary value has been set in DRAS2 to DRAS0, a write of a different value other than
000 must not be performed.
Rev. 3.00 Sep 14, 2005 page 159 of 910
REJ09B0258-0300
Section 6 Bus Controller
Settings of Bits DRAS2 to DRAS0 and Corresponding DRAM Space (RAS
Output Pin)
Table 6.5
DRAS2 DRAS1 DRAS0 Area 5
Area 4
Area 3
Area 2
0
0
1
1
0
1
0
Normal space
Normal space
Normal space
Normal space
1
Normal space
Normal space
Normal space
DRAM space
(CS2)
0
Normal space
Normal space
DRAM space
(CS3)
DRAM space
(CS2)
1
Normal space
Normal space
DRAM space
(CS2)*
DRAM space
(CS2)*
0
Normal space
DRAM space
(CS4)
DRAM space
(CS3)
DRAM space
(CS2)
1
DRAM space
(CS5)
DRAM space
(CS4)
DRAM space
(CS3)
DRAM space
(CS2)
0
DRAM space
(CS4)*
DRAM space
(CS4)*
DRAM space
(CS2)*
DRAM space
(CS2)*
1
DRAM space
(CS2)*
DRAM space
(CS2)*
DRAM space
(CS2)*
DRAM space
(CS2)*
Note: * A single CSn pin serves as a common RAS output pin for a number of areas. Unused CSn
pins can be used as input/output ports.
6.5.3
Address Multiplexing
When DRAM space is accessed, the row address and column address are multiplexed. The
address multiplexing method is selected with bits MXC1 and MXC0 in DRCRB according to the
number of bits in the DRAM column address. Table 6.6 shows the correspondence between the
settings of MXC1 and MXC0 and the address multiplexing method.
Rev. 3.00 Sep 14, 2005 page 160 of 910
REJ09B0258-0300
Section 6 Bus Controller
Table 6.6
Settings of Bits MXC1 and MXC0 and Address Multiplexing Method
DRCRB
Row
address
Address Pins
MXC1 MXC0 Bits
A23 to A13 A12 A11 A10 A9
A1
A0
0
A8
1
Column
address
Column
Address
—
A8
A7
A6
A5
A4
A3
A2
0
8 bits
A23 to A13 A20* A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9
1
9 bits
A23 to A13 A12 A20* A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9
0
10 bits
A23 to A13 A12 A11 A20* A19 A18 A17 A16 A15 A14 A13 A12 A11 A10
1
Illegal
setting
—
—
—
—
—
—
—
—
—
—
—
—
—
A23 to A13 A12 A11 A10 A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
—
—
—
Note: * Row address bit A20 is not multiplexed in 1-Mbyte mode.
6.5.4
Data Bus
If the bit in ABWCR corresponding to an area designated as DRAM space is set to 1, that area is
designated as 8-bit DRAM space; if the bit is cleared to 0, the area is designated as 16-bit DRAM
space. In 16-bit DRAM space, × 16-bit organization DRAM can be connected directly.
In 8-bit DRAM space the upper half of the data bus, D15 to D8, is enabled, while in 16-bit DRAM
space both the upper and lower halves of the data bus, D15 to D0, are enabled.
Access sizes and data alignment are the same as for the basic bus interface: see section 6.4.2,
Data Size and Data Alignment.
Rev. 3.00 Sep 14, 2005 page 161 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.5.5
Pins Used for DRAM Interface
Table 6.7 shows the pins used for DRAM interfacing and their functions.
Table 6.7
DRAM Interface Pins
Pin
With DRAM
Designated Name
I/O
Function
PB4
UCAS
Upper column
address strobe
Output
Upper column address strobe for DRAM
space access (when CSEL = 0 in DRCRB)
PB5
LCAS
Lower column
address strobe
Output
Lower column address strobe for DRAM
space access (when CSEL = 0 in DRCRB)
HWR
UCAS
Upper column
address strobe
Output
Upper column address strobe for DRAM
space access (when CSEL = 1 in DRCRB)
LWR
LCAS
Lower column
address strobe
Output
Lower column address strobe for DRAM
space access (when CSEL = 1 in DRCRB)
CS2
RAS2
Row address
strobe 2
Output
Row address strobe for DRAM space
access
CS3
RAS3
Row address
strobe 3
Output
Row address strobe for DRAM space
access
CS4
RAS4
Row address
strobe 4
Output
Row address strobe for DRAM space
access
CS5
RAS5
Row address
strobe 5
Output
Row address strobe for DRAM space
access
RD
WE
Write enable
Output
Write enable for DRAM space write
access*
P80
RFSH
Refresh
Output
Goes low in refresh cycle
A12 to A0 A12 to A0
Address
Output
Row address/column address multiplexed
output
D15 to D0 D15 to D0
Data
I/O
Data input/output pins
Note: * Fixed high in a read access.
6.5.6
Basic Timing
Figure 6.18 shows the basic access timing for DRAM space. The basic DRAM access timing is
four states: one precharge cycle (Tp) state, one row address output cycle (Tr) state, and two
column address output cycle (Tc1, Tc2) states. Unlike the basic bus interface, the corresponding
bits in ASTCR control only enabling or disabling of wait insertion between Tc1 and Tc2, and do
not affect the number of access states. When the corresponding bit in ASTCR is cleared to 0,
wait states cannot be inserted between Tc1 and Tc2 in the DRAM access cycle.
Rev. 3.00 Sep 14, 2005 page 162 of 910
REJ09B0258-0300
Section 6 Bus Controller
If a DRAM read/write cycle is followed by an access cycle for an external area other than DRAM
space when HWR and LWR are selected as the UCAS and LCAS output pins, an idle cycle (Ti) is
inserted unconditionally immediately after the DRAM access cycle. See section 6.9, Idle Cycle,
for details.
Tp
Tr
Tc1
Tc2
φ
A23 to A0
AS
Row
Column
High level
CSn (RAS)
PB4 /PB5
(UCAS / LCAS)
Read access
RD(WE)
High level
D15 to D0
PB4 /PB5
(UCAS / LCAS)
Write access
RD(WE)
D15 to D0
Note: n = 2 to 5
Figure 6.18 Basic Access Timing (CSEL = 0 in DRCRB)
Rev. 3.00 Sep 14, 2005 page 163 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.5.7
Precharge State Control
In the H8/3068F, provision is made for the DRAM RAS precharge time by always inserting one
RAS precharge state (Tp) when DRAM space is accessed. This can be changed to two Tp states
by setting the TPC bit to 1 in DRCRB. The optimum number of Tp cycles should be set
according to the DRAM connected and the operating frequency of the H8/3068F chip. Figure
6.19 shows the timing when two Tp states are inserted.
When the TCP bit is set to 1, two Tp states are also used for CAS-before-RAS refresh cycles.
Tp1
Tp2
Tr
Tc1
Tc2
φ
A23 to A0
AS
Row
Column
High level
CSn (RAS)
PB4 /PB5
(UCAS /LCAS)
RD(WE)
Read access
High level
D15 to D0
PB4 /PB5
(UCAS /LCAS)
RD(WE)
Write access
D15 to D0
Note: n = 2 to 5
Figure 6.19 Timing with Two Precharge States (CSEL = 0 in DRCRB)
Rev. 3.00 Sep 14, 2005 page 164 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.5.8
Wait Control
In a DRAM access cycle, wait states can be inserted (1) between the Tr state and Tc1 state, and (2)
between the Tc1 state and Tc2 state.
Insertion of Trw Wait State between Tr and Tc1: One Trw state can be inserted between Tr and
Tc1 by setting the RCW bit to 1 in DRCRB.
Insertion of Tw Wait State(s) between Tc1 and Tc2: When the bit in ASTCR corresponding to an
area designated as DRAM space is set to 1, from 0 to 3 wait states can be inserted between the T c1
state and Tc2 state by means of settings in WCRH and WCRL.
Figure 6.20 shows an example of the timing for wait state insertion.
The settings of the RCW bit in DRCRB and of ASTCR, WCRH, and WCRL do not affect refresh
cycles. Wait states cannot be inserted in a DRAM space access cycle by means of the WAIT pin.
Rev. 3.00 Sep 14, 2005 page 165 of 910
REJ09B0258-0300
Section 6 Bus Controller
Tp
Tr
Trw
Tc1
Tw
Tw
Tc2
φ
A23 to A0
AS
Row
Column
High level
CSn(RAS)
Read access
PB4/PB5
(UCAS /LCAS)
RD(WE)
D15 to D0
High level
Read data
PB4/PB5
(UCAS /LCAS)
Write access
RD(WE)
D15 to D0
Write data
Note: n = 2 to 5
Figure 6.20 Example of Wait State Insertion Timing (CSEL = 0)
6.5.9
Byte Access Control and CAS Output Pin
When an access is made to DRAM space designated as a 16-bit-access area in ABWCR, column
address strobes (UCAS and LCAS) corresponding to the upper and lower halves of the external
data bus are output. In the case of × 16-bit organization DRAM, the 2-CAS type can be
connected.
Either PB4 and PB5, or HWR and LWR, can be used as the UCAS and LCAS output pins, the
selection being made with the CSEL bit in DRCRB. Table 6.8 shows the CSEL bit settings and
corresponding output pin selections.
Rev. 3.00 Sep 14, 2005 page 166 of 910
REJ09B0258-0300
Section 6 Bus Controller
When an access is made to DRAM space designated as an 8-bit-access area in ABWCR, only
UCAS is output. When the entire DRAM space is designated as 8-bit-access space and CSEL =
0, PB5 can be used as an input/output port.
Note that RAS down mode cannot be used when a device other than DRAM is connected to
external space and HWR and LWR are used as write strobes. In this case, also, an idle cycle (Ti)
is always inserted when an external access to other than DRAM space occurs after a DRAM
space access. For details, see section 6.9, Idle Cycle.
CSEL Settings and UCAS and LCAS Output Pins
Table 6.8
CSEL
UCAS
LCAS
0
PB4
PB5
1
HWR
LWR
Figure 6.21 shows the control timing.
Tp
Tr
Tc1
Row
Column
Tc2
φ
A23 to A0
CSn (RAS)
PB4(UCAS)
Byte control
PB5(LCAS)
RD(WE)
Note: n = 2 to 5
Figure 6.21 Control Timing (Upper-Byte Write Access When CSEL = 0)
Rev. 3.00 Sep 14, 2005 page 167 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.5.10
Burst Operation
With DRAM, in addition to full access (normal access) in which data is accessed by outputting a
row address for each access, a fast page mode is also provided which can be used when making a
number of consecutive accesses to the same row address. This mode enables fast (burst) access
of data by simply changing the column address after the row address has been output. Burst
access can be selected by setting the BE bit to 1 in DRCRA.
Burst Access (Fast Page Mode) Operation Timing: Figure 6.22 shows the operation timing for
burst access. When there are consecutive access cycles for DRAM space, the column address and
CAS signal output cycles (two states) continue as long as the row address is the same for
consecutive access cycles. In burst access, too, the bus cycle can be extended by inserting wait
states between Tc1 and Tc2. The wait state insertion method and timing are the same as for full
access: see section 6.5.8, Wait Control, for details.
The row address used for the comparison is determined by the bus width of the relevant area set
in bits MXC1 and MXC0 in BRCRB, and in ABWCR. Table 6.9 shows the compared row
addresses corresponding to the various settings of bits MXC1 and MXC0, and ABWCR.
Rev. 3.00 Sep 14, 2005 page 168 of 910
REJ09B0258-0300
Section 6 Bus Controller
Tp
Tr
Tc1
Tc2
Tc1
Tc2
φ
A23 to A0
AS
Row
Column 1
Column 2
High level
CSn(RAS)
PB4/PB5
(UCAS /LCAS)
Read access
RD(WE)
D15 to D0
PB4/PB5
(UCAS/LCAS)
Write access
RD(WE)
D15 to D0
Note: n = 2 to 5
Figure 6.22 Operation Timing in Fast Page Mode
Rev. 3.00 Sep 14, 2005 page 169 of 910
REJ09B0258-0300
Section 6 Bus Controller
Table 6.9
Correspondence between Settings of MXC1 and MXC0 Bits and ABWCR, and
Row Address Compared in Burst Access
DRCRB
ABWCR
Operating Mode
MXC1
MXC0
ABWn
Bus Width
Compared Row Address
Modes 1 and 2
(1-Mbyte)
0
0
0
16 bits
A19 to A9
1
8 bits
A19 to A8
0
16 bits
A19 to A10
1
8 bits
A19 to A9
1
1
Modes 3, 4, and 5
(16-Mbyte)
0
0
0
16 bits
A19 to A11
1
8 bits
A19 to A10
1
—
—
Illegal setting
0
0
16 bits
A23 to A9
1
8 bits
A23 to A8
1
1
0
1
0
16 bits
A23 to A10
1
8 bits
A23 to A9
0
16 bits
A23 to A11
1
8 bits
A23 to A10
—
—
Illegal setting
Note: n = 2 to 5
RAS Down Mode and RAS Up Mode: With DRAM provided with fast page mode, as long as
accesses are to the same row address, burst operation can be continued without interruption even
if accesses are not consecutive by holding the RAS signal low.
• RAS Down Mode
To select RAS down mode, set the BE and RDM bits to 1 in DRCRA. If access to DRAM
space is interrupted and another space is accessed, the RAS signal is held low during the
access to the other space, and burst access is performed if the row address of the next DRAM
space access is the same as the row address of the previous DRAM space access. Figure 6.23
shows an example of the timing in RAS down mode.
Rev. 3.00 Sep 14, 2005 page 170 of 910
REJ09B0258-0300
Section 6 Bus Controller
External space
access
DRAM access
Tp
Tr
Tc1
Tc2
T1
T2
DRAM access
Tc1
Tc2
φ
A23 to A0
AS
CSn (RAS)
PB4/PB5
(UCAS/LCAS)
D15 to D0
Note: n = 2 to 5
Figure 6.23 Example of Operation Timing in RAS Down Mode (CSEL = 0)
When RAS down mode is selected, the conditions for an asserted RASn signal to return to the
high level are as shown below. The timing in these cases is shown in figure 6.24.
 When DRAM space with a different row address is accessed
 Immediately before a CAS-before-RAS refresh cycle
 When the BE bit or RDM bit is cleared to 0 in DRCRA
 Immediately before release of the external bus
Rev. 3.00 Sep 14, 2005 page 171 of 910
REJ09B0258-0300
Section 6 Bus Controller
DRAM access cycle
φ
RASn
(a) Access to DRAM space with a different row address
CBR refresh cycle
φ
RASn
(b) CAS-before-RAS refresh cycle
DRCRA write cycle
φ
RASn
(c) BE bit or RDM bit cleared to 0 in DRCRA
External bus released
φ
High-impedance
RASn
(d) External bus released
Note: n = 2 to 5
Figure 6.24
RASn Negation Timing when RAS Down Mode is Selected
Rev. 3.00 Sep 14, 2005 page 172 of 910
REJ09B0258-0300
Section 6 Bus Controller
When RAS down mode is selected, the CAS-before-RAS refresh function provided with this
DRAM interface must always be used as the DRAM refreshing method. When a refresh
operation is performed, the RAS signal goes high immediately beforehand. The refresh
interval setting must be made so that the maximum DRAM RAS pulse width specification is
observed.
When the self-refresh function is used, the RDM bit must be cleared to 0, and RAS up mode
selected, before executing a SLEEP instruction in order to enter software standby mode.
Select RAS down mode again after exiting software standby mode.
Note that RAS down mode cannot be used when HWR and LWR are selected for UCAS and
LCAS, a device other than DRAM is connected to external space, and HWR and LWR are
used as write strobes.
• RAS Up Mode
To select RAS up mode, clear the RDM bit to 0 in DRCRA. Each time access to DRAM
space is interrupted and another space is accessed, the RAS signal returns to the high level.
Burst operation is only performed if DRAM space is continuous. Figure 6.25 shows an
example of the timing in RAS up mode.
DRAM access
Tp
Tr
Tc1
DRAM access
Tc2
Tc1
Tc2
External space
access
T1
T2
φ
A23 to A0
AS
CSn(RAS)
PB4/PB5
(UCAS/LCAS)
D15 to D0
Note: n = 2 to 5
Figure 6.25 Example of Operation Timing in RAS Up Mode
Rev. 3.00 Sep 14, 2005 page 173 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.5.11
Refresh Control
The H8/3068F is provided with a CAS-before-RAS (CBR) function and self-refresh function as
DRAM refresh control functions.
CAS-Before-RAS (CBR) Refreshing: To select CBR refreshing, set the RCYCE bit to 1 in
DRCRB.
With CBR refreshing, RTCNT counts up using the input clock selected by bits CKS2 to CKS0 in
RTMCSR, and a refresh request is generated when the count matches the value set in RTCOR
(compare match). At the same time, RTCNT is reset and starts counting up again from H'00.
Refreshing is thus repeated at fixed intervals determined by RTCOR and bits CKS2 to CKS0. A
refresh cycle is executed after this refresh request has been accepted and the DRAM interface has
acquired the bus. Set a value in bits CKS2 to CKS0 in RTCOR that will meet the refresh interval
specification for the DRAM used. When RAS down mode is used, set the refresh interval so that
the maximum RAS pulse width specification is met.
RTCNT starts counting up when bits CKS2 to CKS0 are set. RTCNT and RTCOR settings
should therefore be completed before setting bits CKS2 to CKS0.
Also note that a repeat refresh request generated during a bus request, or a refresh request during
refresh cycle execution, will be ignored.
RTCNT operation is shown in figure 6.26, compare match timing in figure 6.27, and CBR refresh
timing in figures 6.28 and 6.29.
RTCNT
RTCOR
H'00
Refresh request
Figure 6.26 RTCNT Operation
Rev. 3.00 Sep 14, 2005 page 174 of 910
REJ09B0258-0300
Section 6 Bus Controller
φ
RTCNT
N
H'00
RTCOR
N
Refresh request signal
and CMF bit setting signal
Figure 6.27 Compare Match Timing
TRp
TR1
TR2
φ
Address bus*
Area 2 start address
CSn(RAS)
PB4/PB5
(UCAS/LCAS)
RD(WE)
High
RFSH
AS
High level
Note: * In address update mode 1, the area 2 start address is output.
In address update mode 2, the address in the preceding bus cycle is retained.
Figure 6.28 CBR Refresh Timing (CSEL = 0, TPC = 0, RLW = 0)
The basic CBS refresh cycle timing comprises three states: one RAS precharge cycle (TRP) state,
and two RAS output cycle (TR1, TR2) states. Either one or two states can be selected for the RAS
Rev. 3.00 Sep 14, 2005 page 175 of 910
REJ09B0258-0300
Section 6 Bus Controller
precharge cycle. When the TPC bit is set to 1 in DRCRB, RAS signal output is delayed by one
cycle. This does not affect the timing of UCAS and LCAS output.
Use the RLW bit in DRCRB to adjust the RAS signal width. A single refresh wait state (TRW) can
be inserted between the TR1 state and TR2 state by setting the RLW bit to 1.
The RLW bit setting is valid only for CBR refresh cycles, and does not affect DRAM read/write
cycles. The number of states in the CBR refresh cycle is not affected by the settings in ASTCR,
WCRH, or WCRL, or by the state of the WAIT pin.
Figure 6.29 shows the timing when the TPC bit and RLW bit are both set to 1.
TRp1
TRP2
TR1
TRW
TR2
φ
Address bus*
Area 2 start address
CSn(RAS)
PB4/PB5
(UCAS/LCAS)
RD(WE)
High
RFSH
AS
High level
Note: * In address update mode 1, the area 2 start address is output.
In address update mode 2, the address in the preceding bus cycle is retained.
Figure 6.29 CBR Refresh Timing (CSEL = 0, TPC = 1, RLW = 1)
DRAM must be refreshed immediately after powering on in order to stabilize its internal state.
When using the H8/3068F CAS-before-RAS refresh function, therefore, a DRAM stabilization
period should be provided by means of interrupts by another timer module, or by counting the
Rev. 3.00 Sep 14, 2005 page 176 of 910
REJ09B0258-0300
Section 6 Bus Controller
number of times bit 7 (CMF) of RTMCSR is set, for instance, immediately after bits DRAS2 to
DRAS0 have been set in DRCRA.
Self-Refreshing: A self-refresh mode (battery backup mode) is provided for DRAM as a kind of
standby mode. In this mode, refresh timing and refresh addresses are generated within the
DRAM. The H8/3068F has a function that places the DRAM in self-refresh mode when the chip
enters software standby mode.
To use the self-refresh function, set the SRFMD bit to 1 in DRCRA. When a SLEEP instruction
is subsequently executed in order to enter software standby mode, the CAS and RAS signals are
output and the DRAM enters self-refresh mode, as shown in figure 6.30.
When the chip exits software standby mode, CAS and RAS outputs go high.
The following conditions must be observed when the self-refresh function is used:
• When burst access is selected, RAS up mode must be selected before executing a SLEEP
instruction in order to enter software standby mode. Therefore, if RAS down mode has been
selected, the RDM bit in DRCRA must be cleared to 0 and RAS up mode selected before
executing the SLEEP instruction. Select RAS down mode again after exiting software standby
mode.
• The instruction immediately following a SLEEP instruction must not be located in an area
designated as DRAM space.
The self-refresh function will not work properly unless the above conditions are observed.
Rev. 3.00 Sep 14, 2005 page 177 of 910
REJ09B0258-0300
Section 6 Bus Controller
Software standby
mode
Oscillation stabilization
time
φ
High-impedance
Address bus
CSn(RAS)
PB4(UCAS)
PB5(LCAS)
RD(WE)
RFSH
Figure 6.30 Self-Refresh Timing (CSEL = 0)
Refresh Signal (RFSH): A refresh signal (RFSH) that transmits a refresh cycle off-chip can be
output by setting the RFSHE bit to 1 in DRCRA. RFSH output timing is shown in figures 6.28,
6.29, and 6.30.
6.5.12
Examples of Use
Examples of DRAM connection and program setup procedures are shown below. When the
DRAM interface is used, check the DRAM device characteristics and choose the most
appropriate method of use for that device.
Connection Examples
• Figure 6.31 shows typical interconnections when using two 2-CAS type 16-Mbit DRAMs
using a × 16-bit organization, and the corresponding address map. The DRAMs used in this
example are of the 10-bit row address × 10-bit column address type. Up to four DRAMs can
be connected by designating areas 2 to 5 as DRAM space.
Rev. 3.00 Sep 14, 2005 page 178 of 910
REJ09B0258-0300
Section 6 Bus Controller
2-CAS 16-Mbit DRAM
10-bit row address x 10-bit column address
x16-bit organization
H8/3067 Group chip
CS2 (RAS2)
CS3 (RAS3)
PB4(UCAS)
PB5(LCAS)
RD (WE)
RAS
UCAS
LCAS
WE
A10-A1
A9-A0
D15-D0
D15-D0
No.1
OE
RAS
UCAS
LCAS
WE
No.2
A9-A0
D15-D0
OE
(a) Interconnections (example)
PB5
(LCAS)
PB4
(UCAS)
15
87
0
H'400000
Area 2
DRAM (No.1)
CS2(RAS2)
DRAM (No.2)
CS3(RAS3)
H'5FFFFE
H'600000
Area 3
H'7FFFFE
H'800000
Area 4
Normal
CS4
Normal
CS5
H'9FFFFE
H'A00000
Area 5
H'BFFFFE
(b) Address map
Figure 6.31 Interconnections and Address Map for 2-CAS 16-Mbit DRAMs with ×
16-Bit Organization
• Figure 6.32 shows typical interconnections when using two 16-Mbit DRAMs using a × 8-bit
organization, and the corresponding address map. The DRAMs used in this example are of the
11-bit row address × 10-bit column address type. The CS2 pin is used as the common RAS
output pin for areas 2 and 3. When the DRAM address space spans a number of contiguous
Rev. 3.00 Sep 14, 2005 page 179 of 910
REJ09B0258-0300
Section 6 Bus Controller
areas, as in this example, the appropriate setting of bits DRAS2 to DRAS0 enables a single CS
pin to be used as the common RAS output pin for a number of areas, and makes it possible to
directly connect large-capacity DRAM with address space that spans a maximum of four
areas. Any unused CS pins (in this example, the CS3 pin) can be used as input/output ports.
2-CAS 16-Mbit DRAM
11-bit row address x 10-bit column address
x8-bit organization
H8/3067 Group chip
RAS
CS2 (RAS2)
PB4 (UCAS)
PB5 (LCAS)
RD (WE)
CAS
WE
A21, A10-A1
No.1
A10-A0
D7-D0
D15-D8
D7-D0
OE
RAS
CAS
WE
No.2
A10-A0
D7-D0
OE
(a) Interconnections (example)
PB4
PB5
(UCAS)
(LCAS)
15
87
0
H'400000
Area 2
H'5FFFFE
H'600000
DRAM
(No.1)
DRAM
(No.2)
CS2(RAS2)
Area 3
H'7FFFFE
H'800000
Area 4
Normal
CS4
Normal
CS5
H'9FFFFE
H'A00000
Area 5
H'BFFFFE
16-Mbyte mode
(b) Address map
Figure 6.32 Interconnections and Address Map for 16-Mbit DRAMs with × 8-Bit
Organization
Rev. 3.00 Sep 14, 2005 page 180 of 910
REJ09B0258-0300
Section 6 Bus Controller
• Figure 6.33 shows typical interconnections when using two 4-Mbit DRAMs, and the
corresponding address map. The DRAMs used in this example are of the 9-bit row address ×
10-bit column address type. In this example, upper address decoding allows multiple DRAMs
to be connected to a single area. The RFSH pin is used in this case, since both DRAMs must
be refreshed simultaneously. However, note that RAS down mode cannot be used in this
interconnection example.
Rev. 3.00 Sep 14, 2005 page 181 of 910
REJ09B0258-0300
Section 6 Bus Controller
2-CAS 4-Mbit DRAM
9-bit row address x 9-bit column address
x16-bit organization
H8/3067 Group chip
CS2 (RAS2)
PB4 (UCAS)
RAS
UCAS
PB5 (LCAS)
RD (WE)
LCAS
WE
No.1
RFSH
A19
A9-A1
A8-A0
D15-D0
D15-D0
RAS
UCAS
LCAS
WE
OE
No.2
A8-A0
D15-D0
OE
(a) Interconnections (example)
PB4
(UCAS)
15
PB5
(LCAS)
87
0
H'400000
DRAM (No.1)
H'47FFFE
H'480000
DRAM (No.2)
Area 2
H'4FFFFE
H'500000
CS2 (RAS2)
Not used
H'5FFFFE
16-Mbyte mode
(b) Address map
Figure 6.33 Interconnections and Address Map for 2-CAS 4-Mbit DRAMs with × 16-Bit
Organization
Rev. 3.00 Sep 14, 2005 page 182 of 910
REJ09B0258-0300
Section 6 Bus Controller
Example of Program Setup Procedure: Figure 6.34 shows an example of the program setup
procedure.
Set ABWCR
Set RTCOR
Set bits CKS2 to CKS0 in RTMCSR
Set DRCRB
Set DRCRA
Wait for DRAM stabilization time
DRAM can be accessed
Figure 6.34 Example of Setup Procedure when Using DRAM Interface
6.5.13
Usage Notes
Note the following points when using the DRAM refresh function.
• Refresh cycles will not be executed when the external bus released state, software standby
mode, or a bus cycle is extended by means of wait state insertion. Refreshing must therefore
be performed by other means in these cases.
• If a refresh request is generated internally while the external bus is released, the first request is
retained and a single refresh cycle will be executed after the bus-released state is cleared.
Figure 6.35 shows the bus cycle in this case.
• When a bus cycle is extended by means of wait state insertion, the first request is retained in
the same way as when the external bus has been released.
Rev. 3.00 Sep 14, 2005 page 183 of 910
REJ09B0258-0300
Section 6 Bus Controller
• In the event of contention with a bus request from an external bus master when a transition is
made to software standby mode, the BACK and strobe states may be indeterminate after the
transition to software standby mode (see figure 6.36).
When software standby mode is used, the BRLE bit should be cleared to 0 in BRCR before
executing the SLEEP instruction.
Similar contention in a transition to self-refresh mode may prevent dependable strobe
waveform output. This can also be avoided by clearing the BRLW bit to 0 in BRCR.
• Immediately after self-refreshing is cleared, external bus release is possible during a given
period until the start of a CPU cycle. Attention must be paid to the RAS state to ensure that
the specification for the RAS precharge time immediately after self-refreshing is met.
External bus released
Refresh cycle
CPU cycle
φ
RFSH
Refresh
request
BACK
Figure 6.35
Bus-Released State and Refresh Cycles
Rev. 3.00 Sep 14, 2005 page 184 of 910
REJ09B0258-0300
Refresh cycle
Section 6 Bus Controller
Software standby mode
φ
BREQ
BACK
Address bus
Strobe
Figure 6.36 Bus-Released State and Software Standby Mode
Oscillation stabilization
CPU internal cycle
time on exit from software (period in which external
standby mode
bus can be released)
CPU cycle
φ
Address
@SP
RAS
CAS
Figure 6.37 Self-Refresh Clearing
Rev. 3.00 Sep 14, 2005 page 185 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.6
Interval Timer
6.6.1
Operation
When DRAM is not connected to the H8/3068F chip, the refresh timer can be used as an interval
timer by clearing bits DRAS2 to DRAS0 in DRCRA to 0. After setting RTCOR, selection a clock
source with bits CKS2 to CKS0 in RTMCSR, and set the CMIE bit to 1.
Timing of Setting of Compare Match Flag and Clearing by Compare Match: The CMF flag
in RTMCSR is set to 1 by a compare match output when the RTCOR and RTCNT values match.
The compare match signal is generated in the last state in which the values match (when RTCNT
is updated from the matching value to a new value). Accordingly, when RTCNT and RTCOR
match, the compare match signal is not generated until the next counter clock pulse. Figure 6.38
shows the timing.
φ
RTCNT
N
H'00
N
RTCOR
Compare match
signal
CMF flag
Figure 6.38 Timing of CMF Flag Setting
Rev. 3.00 Sep 14, 2005 page 186 of 910
REJ09B0258-0300
Section 6 Bus Controller
Operation in Power-Down State: The interval timer operates in sleep mode. It does not operate
in hardware standby mode. In software standby mode, RTCNT and RTMCSR bits 7 and 6 are
initialized, but RTMCSR bits 5 to 3 and RTCOR retain their settings prior to the transition to
software standby mode.
Contention between RTCNT Write and Counter Clear: If a counter clear signal occurs in the
T3 state of an RTCNT write cycle, clearing of the counter takes priority and the write is not
performed. See Figure 6.39.
T1
T2
T3
φ
Address bus
RTCNT address
Internal write signal
Counter clear signal
RTCNT
N
H'00
Figure 6.39 Contention between RTCNT Write and Clear
Rev. 3.00 Sep 14, 2005 page 187 of 910
REJ09B0258-0300
Section 6 Bus Controller
Contention between RTCNT Write and Increment: If an increment pulse occurs in the T3
state of an RTCNT write cycle, writing takes priority and RTCNT is not incremented. See Figure
6.40.
T1
T2
T3
φ
Address bus
RTCNT address
Internal write signal
RTCNT input clock
RTCNT
N
M
Counter write data
Figure 6.40 Contention between RTCNT Write and Increment
Rev. 3.00 Sep 14, 2005 page 188 of 910
REJ09B0258-0300
Section 6 Bus Controller
Contention between RTCOR Write and Compare Match: If a compare match occurs in the T3
state of an RTCOR write cycle, writing takes priority and the compare match signal is inhibited.
See Figure 6.41.
T1
T2
T3
φ
Address bus
RTCOR address
Internal write signal
RTCNT
N
N+1
RTCOR
N
M
RTCOR write data
Compare match signal
Inhibited
Figure 6.41 Contention between RTCOR Write and Compare Match
RTCNT Operation at Internal Clock Source Switchover: Switching internal clock sources
may cause RTCNT to increment, depending on the switchover timing. Table 6.10 shows the
relation between the time of the switchover (by writing to bits CKS2 to CKS0) and the operation
of RTCNT.
The RTCNT input clock is generated from the internal clock source by detecting the falling edge
of the internal clock. If a switchover is made from a high clock source to a low clock source, as
in case No. 3 in table 6.10, the switchover will be regarded as a falling edge, an RTCNT clock
pulse will be generated, and RTCNT will be incremented.
Rev. 3.00 Sep 14, 2005 page 189 of 910
REJ09B0258-0300
Section 6 Bus Controller
Table 6.10 Internal Clock Switchover and RTCNT Operation
No.
1
CKS2 to CKS0
Write Timing
Low
Low
switchover*1
RTCNT Operation
Old clock source
New clock source
RTCNT clock
RTCNT
N
N+1
CKS bits rewritten
2
Low
High
switchover*2
Old clock source
New clock source
RTCNT clock
RTCNT
N
N+1
N+2
CKS bits rewritten
Rev. 3.00 Sep 14, 2005 page 190 of 910
REJ09B0258-0300
Section 6 Bus Controller
No.
3
CKS2 to CKS0
Write Timing
High
Low
switchover*3
RTCNT Operation
Old clock source
New clock source
*4
RTCNT clock
RTCNT
N
N+1
N+2
CKS bits rewritten
4
High
High
switchover*4
Old clock source
New clock source
RTCNT clock
RTCNT
N
N+1
N+2
CKS bits rewritten
Notes: 1.
2.
3.
4.
Including switchovers from a low clock source to the halted state, and from the halted state to a low clock source.
Including switchover from the halted state to a high clock source.
Including switchover from a high clock source to the halted state.
The switchover is regarded as a falling edge, causing RTCNT to increment.
Rev. 3.00 Sep 14, 2005 page 191 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.7
Interrupt Sources
Compare match interrupts (CMI) can be generated when the refresh timer is used as an interval
timer. Compare match interrupt requests are masked/unmasked with the CMIE bit in RTMCSR.
6.8
Burst ROM Interface
6.8.1
Overview
With the H8/3068F, external space area 0 can be designated as burst ROM space, and burst ROM
space interfacing can be performed. The burst ROM space interface enables 16-bit organization
ROM with burst access capability to be accessed at high speed. Area 0 is designated as burst
ROM space by means of the BROME bit in BCR.
Continuous burst access of a maximum or four or eight words can be performed on external space
area 0. Two or three states can be selected for burst access.
6.8.2
Basic Timing
The number of states in the initial cycle (full access) and a burst cycle of the burst ROM interface
is determined by the setting of the AST0 bit in ASTCR. When the AST0 bit is set to 1, wait states
can also be inserted in the initial cycle. Wait states cannot be inserted in a burst cycle.
Burst access of up to four words is performed when the BRSTS0 bit is cleared to 0 in BCR, and
burst access of up to eight words when the BRSTS0 bit is set to 1. The number of burst access
states is two when the BRSTS1 bit is cleared to 0, and three when the BRSTS1 bit is set to 1.
The basic access timing for burst ROM space is shown in figure 6.42.
Rev. 3.00 Sep 14, 2005 page 192 of 910
REJ09B0258-0300
Section 6 Bus Controller
Full access
T1
T2
Burst access
T3
T1
T2
T1
T2
φ
Address bus
Only lower address changes
CS0
AS
RD
Data bus
Read data
Read data
Read data
Figure 6.42 Example of Burst ROM Access Timing
6.8.3
Wait Control
As with the basic bus interface, either program wait insertion or pin wait insertion using the
WAIT pin can be used in the initial cycle (full access) of the burst ROM interface.
Wait states cannot be inserted in a burst cycle.
Rev. 3.00 Sep 14, 2005 page 193 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.9
Idle Cycle
6.9.1
Operation
When the H8/3068F chip accesses external space, it can insert a 1-state idle cycle (TI) between
bus cycles in the following cases: (1) when read accesses between different areas occur
consecutively, (2) when a write cycle occurs immediately after a read cycle, and (3) immediately
after a DRAM space access. By inserting an idle cycle it is possible, for example, to avoid data
collisions between ROM, which has a long output floating time, and high-speed memory, I/O
interfaces, and so on.
The ICIS1 and ICIS0 bits in BCR both have an initial value of 1, so that an idle cycle is inserted
in the initial state. If there are no data collisions, the ICIS bits can be cleared.
Consecutive Reads between Different Areas: If consecutive reads between different areas
occur while the ICIS1 bit is set to 1 in BCR, an idle cycle is inserted at the start of the second
read cycle.
Figure 6.43 shows an example of the operation in this case. In this example, bus cycle A is a read
cycle from ROM with a long output floating time, and bus cycle B is a read cycle from SRAM,
each being located in a different area. In (a), an idle cycle is not inserted, and a collision occurs
in cycle B between the read data from ROM and that from SRAM. In (b), an idle cycle is
inserted, and a data collision is prevented.
Bus cycle A Bus cycle B
φ
T1
T2
T3
T1
T2
Bus cycle A Bus cycle B
φ
Address bus
Address bus
RD
RD
Data bus
Data bus
Long buffer-off
time
(a) Idle cycle not inserted
T1
T2
T3
Ti T1
Data
collision
(b) Idle cycle inserted
Figure 6.43 Example of Idle Cycle Operation (1) (ICIS1 = 1)
Rev. 3.00 Sep 14, 2005 page 194 of 910
REJ09B0258-0300
T2
Section 6 Bus Controller
Write after Read: If an external write occurs after an external read while the ICIS0 bit is set to
1 in BCR, an idle cycle is inserted at the start of the write cycle.
Figure 6.44 shows an example of the operation in this case. In this example, bus cycle A is a read
cycle from ROM with a long output floating time, and bus cycle B is a CPU write cycle.
In (a), an idle cycle is not inserted, and a collision occurs in cycle B between the read data from
ROM and the CPU write data. In (b), an idle cycle is inserted, and a data collision is prevented.
Bus cycle A Bus cycle B
φ
T1
T2
T3
T1
T2
Bus cycle A Bus cycle B
φ
Address bus
T1
T2
T3
Ti T1
T2
Address bus
RD
RD
HWR
HWR
Data bus
Data bus
Long buffer-off
time
(a) Idle cycle not inserted
Data
collision
(b) Idle cycle inserted
Figure 6.44 Example of Idle Cycle Operation (2) (ICIS0 = 1)
External Address Space Access Immediately after DRAM Space Access: If a DRAM space
access is followed by a non-DRAM external access when HWR and LWR have been selected as
the UCAS and LCAS output pins by means of the CSEL bit in DRCRB, a Ti cycle is inserted
regardless of the settings of bits ICIS0 and ICIS1 in BCR. Figure 6.45 shows an example of the
operation.
This is done to prevent simultaneous changing of the HWR and LWR signals used as UCAS and
LCAS in DRAM space and CSn for the space in the next cycle, and so avoid an erroneous write
to the external device in the next cycle.
A Ti cycle is not inserted when PB4 and PB5 have been selected as the UCAS and LCAS output
pins.
In the case of consecutive DRAM space access precharge cycles (Tp), the ICIS0 and ICIS1 bit
settings are invalid. In the case of consecutive reads between different areas, for example, if the
second access is a DRAM access, only a Tp cycle is inserted, and a Ti cycle is not. The timing in
this case is shown in figure 6.46.
Rev. 3.00 Sep 14, 2005 page 195 of 910
REJ09B0258-0300
Section 6 Bus Controller
Bus cycle A
(DRAM access cycle) Bus cycle B
φ
Tp
Tr Tc1 Tc2 T1
Bus cycle A
(DRAM access cycle) Bus cycle B
T2
φ
Address bus
Address bus
HWR/LWR
(UCAS/LCAS)
HWR/LWR
(UCAS/LCAS)
CSn
CSn
Tp
Tr Tc1 Tc2 Ti
T1
T2
Simultaneous change of
HWR/LWR and CSn
(a) Idle cycle not inserted
(b) Idle cycle inserted
Figure 6.45 Example of Idle Cycle Operation (3) (HWR/LWR Used as UCAS/LCAS)
External read
T1
T2
T3
DRAM space read
Tp
Tr
Tc1
Tc2
φ
Address bus
RD
UCAS/LCAS
Address bus
Figure 6.46 Example of Idle Cycle Operation (4) (Consecutive Precharge Cycles)
Usage Notes: When non-insertion of idle cycles is set, the rise (negation) of RD and the fall
(assertion) of CSn may occur simultaneously. An example of the operation is shown in figure
6.47.
If consecutive reads between different external areas occur while the ICIS1 bit is cleared to 0 in
BCR, or if a write cycle to a different external area occurs after an external read while the ICIS0
bit is cleared to 0, the RD negation in the first read cycle and the CSn assertion in the following
bus cycle will occur simultaneously. Therefore, depending on the output delay time of each
signal, it is possible that the low-level output of RD in the preceding read cycle and the low-level
output of CSn in the following bus cycle will overlap.
Rev. 3.00 Sep 14, 2005 page 196 of 910
REJ09B0258-0300
Section 6 Bus Controller
A setting whereby idle cycle insertion is not performed can be made only when RD and CSn do
not change simultaneously, or when it does not matter if they do.
Bus cycle A
φ
T1
T2
T3
Bus cycle B
T1
Bus cycle A
T2
φ
Address bus
Address bus
RD
RD
CSn
CSn
T1
T2
T3
Bus cycle B
Ti
T1
T2
Simultaneous change of RD and CSn
Possibility of mutual overlap
(a) Idle cycle not inserted
(b) Idle cycle inserted
Figure 6.47 Example of Idle Cycle Operation (5)
6.9.2
Pin States in Idle Cycle
Table 6.11 shows the pin states in an idle cycle.
Table 6.11 Pin States in Idle Cycle
Pins
Pin State
A23 to A0
Next cycle address value
D15 to D0
High impedance
CSn
UCAS, LCAS
AS
RD
HWR
LWR
High*
High
High
High
High
High
Note: * Remains low in DRAM space RAS down mode.
Rev. 3.00 Sep 14, 2005 page 197 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.10
Bus Arbiter
The bus controller has a built-in bus arbiter that arbitrates between different bus masters. There
are four bus masters: the CPU, DMA controller (DMAC), DRAM interface, and an external bus
master. When a bus master has the bus right it can carry out read, write, or refresh access. Each
bus master uses a bus request signal to request the bus right. At fixed times the bus arbiter
determines priority and uses a bus acknowledge signal to grant the bus to a bus master, which can
the operate using the bus.
The bus arbiter checks whether the bus request signal from a bus master is active or inactive, and
returns an acknowledge signal to the bus master. When two or more bus masters request the bus,
the highest-priority bus master receives an acknowledge signal. The bus master that receives an
acknowledge signal can continue to use the bus until the acknowledge signal is deactivated.
The bus master priority order is:
(High) External bus master > DRAM interface > DMAC > CPU
(Low)
The bus arbiter samples the bus request signals and determines priority at all times, but it does not
always grant the bus immediately, even when it receives a bus request from a bus master with
higher priority than the current bus master. Each bus master has certain times at which it can
release the bus to a higher-priority bus master.
6.10.1
Operation
CPU: The CPU is the lowest-priority bus master. If the DMAC, DRAM interface, or an external
bus master requests the bus while the CPU has the bus right, the bus arbiter transfers the bus right
to the bus master that requested it. The bus right is transferred at the following times:
• The bus right is transferred at the boundary of a bus cycle. If word data is accessed by two
consecutive byte accesses, however, the bus right is not transferred between the two byte
accesses.
• If another bus master requests the bus while the CPU is performing internal operations, such
as executing a multiply or divide instruction, the bus right is transferred immediately. The
CPU continues its internal operations.
• If another bus master requests the bus while the CPU is in sleep mode, the bus right is
transferred immediately.
Rev. 3.00 Sep 14, 2005 page 198 of 910
REJ09B0258-0300
Section 6 Bus Controller
DMAC: When the DMAC receives an activation request, it requests the bus right from the bus
arbiter. If the DMAC is bus master and the DRAM interface or an external bus master requests
the bus, the bus arbiter transfers the bus right from the DMAC to the bus master that requested
the bus. The bus right is transferred at the following times.
The bus right is transferred when the DMAC finishes transferring one byte or one word. A
DMAC transfer cycle consists of a read cycle and a write cycle. The bus right is not transferred
between the read cycle and the write cycle.
There is a priority order among the DMAC channels. For details see section 7.4.9, MultipleChannel Operation.
DRAM Interface: The DRAM interface requests the bus right from the bus arbiter when a
refresh cycle request is issued, and releases the bus at the end of the refresh cycle. For details see
section 6.5, DRAM Interface.
External Bus Master: When the BRLE bit is set to 1 in BRCR, the bus can be released to an
external bus master. The external bus master has highest priority, and requests the bus right from
the bus arbiter y driving the BREQ signal low. Once the external bus master acquires the bus, it
keeps the bus until the BREQ signal goes high. While the bus is released to an external bus
master, the H8/3068F chip holds the address bus, data bus, bus control signals (AS, RD, HWR,
and LWR), and chip select signals (CSn: n = 7 to 0) in the high-impedance state, and holds the
BACK pin in the low output state.
The bus arbiter samples the BREQ pin at the rise of the system clock (φ). If BREQ is low, the
bus is released to the external bus master at the appropriate opportunity. The BREQ signal
should be held low until the BACK signal goes low.
When the BREQ pin is high in two consecutive samples, the BACK pin is driven high to end the
bus-release cycle.
Figure 6.48 shows the timing when the bus right is requested by an external bus master during a
read cycle in a two-state access area. There is a minimum interval of three states from when the
BREQ signal goes low until the bus is released.
Rev. 3.00 Sep 14, 2005 page 199 of 910
REJ09B0258-0300
Section 6 Bus Controller
CPU cycles
T0
φ
T1
External bus released
High-impedance
Address
Address bus
CPU cycles
T2
High-impedance
Data bus
High-impedance
AS
RD
High-impedance
High
High-impedance
HWR, LWR
BREQ
BACK
Minimum 3 cycles
(1)
(2)
(3)
(4)
(5)
(6)
Figure 6.48 Example of External Bus Master Operation
In the event of contention with a bus request from an external bus master when a transition is
made to software standby mode, the BACK and strobe states may be indeterminate after the
transition to software standby mode (see figure 6.36).
When software standby mode is used, the BRLE bit should be cleared to 0 in BRCR before
executing the SLEEP instruction.
Rev. 3.00 Sep 14, 2005 page 200 of 910
REJ09B0258-0300
Section 6 Bus Controller
6.11
Register and Pin Input Timing
6.11.1
Register Write Timing
ABWCR, ASTCR, WCRH, and WCRL Write Timing: Data written to ABWCR, ASTCR,
WCRH, and WCRL takes effect starting from the next bus cycle. Figure 6.49 shows the timing
when an instruction fetched from area 0 changes area 0 from three-state access to two-state
access.
T1
T2
T3
T1
T2
T3
T1
T2
φ
Address bus
ASTCR address
3-state access to area 0
2-state access to area 0
Figure 6.49 ASTCR Write Timing
DDR and CSCR Write Timing: Data written to DDR or CSCR for the port corresponding to the
CSn pin to switch between CSn output and generic input takes effect starting from the T3 state of
the DDR write cycle. Figure 6.50 shows the timing when the CS1 pin is changed from generic
input to CS1 output.
T1
T2
T3
φ
Address bus
P8DDR address
CS1
High-impedance
Figure 6.50 DDR Write Timing
Rev. 3.00 Sep 14, 2005 page 201 of 910
REJ09B0258-0300
Section 6 Bus Controller
BRCR Write Timing: Data written to BRCR to switch between A23, A22, A21, or A20 output and
generic input or output takes effect starting from the T3 state of the BRCR write cycle. Figure
6.51 shows the timing when a pin is changed from generic input to A23, A22, A21, or A20 output.
T1
T2
T3
φ
Address bus
BRCR address
PA7 to PA4
(A23 to A20)
High-impedance
Figure 6.51 BRCR Write Timing
6.11.2
BREQ Pin Input Timing
After driving the BREQ pin low, hold it low until BACK goes low. If BREQ returns to the high
level before BACK goes lows, the bus arbiter may operate incorrectly.
To terminate the external-bus-released state, hold the BREQ signal high for at least three states.
If BREQ is high for too short an interval, the bus arbiter may operate incorrectly.
Rev. 3.00 Sep 14, 2005 page 202 of 910
REJ09B0258-0300
Section 7 DMA Controller
Section 7 DMA Controller
7.1
Overview
The H8/3068F has an on-chip DMA controller (DMAC) that can transfer data on up to four
channels.
When the DMA controller is not used, it can be independently halted to conserve power. For
details see section 20.6, Module Standby Function.
7.1.1
Features
DMAC features are listed below.
• Selection of short address mode or full address mode
Short address mode
 8-bit source address and 24-bit destination address, or vice versa
 Maximum four channels available
 Selection of I/O mode, idle mode, or repeat mode
Full address mode
 24-bit source and destination addresses
 Maximum two channels available
 Selection of normal mode or block transfer mode
• Directly addressable 16-Mbyte address space
• Selection of byte or word transfer
• Activation by internal interrupts, external requests, or auto-request (depending on transfer
mode)
 16-bit timer compare match/input capture interrupts (×3)
 Serial communication interface (SCI channel 0) transmit-data-empty/receive-data-full
interrupts
 External requests
 Auto-request
 A/D converter conversion-end interrupt
Rev. 3.00 Sep 14, 2005 page 203 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.1.2
Block Diagram
Figure 7.1 shows a DMAC block diagram.
Internal address bus
Address buffer
IMIA0
IMIA1
IMIA2
ADI
TXI0
RXI0
DREQ0
DREQ1
TEND0
TEND1
Arithmetic-logic unit
MAR0A
Channel
0A
Control logic
ETCR0A
Channel
0
MAR0B
Channel
0B
DTCR0A
Interrupt DEND0A
signals
DEND0B
DEND1A
DEND1B
MAR1A
Channel
1A
DTCR1A
MAR1B
Internal data bus
Legend
DTCR: Data transfer control register
MAR: Memory address register
IOAR: I/O address register
ETCR: Execute transfer count register
Figure 7.1 Block Diagram of DMAC
Rev. 3.00 Sep 14, 2005 page 204 of 910
REJ09B0258-0300
IOAR1A
ETCR1A
Channel
1
Channel
1B
Data buffer
IOAR0B
ETCR0B
DTCR0B
DTCR1B
IOAR0A
IOAR1B
ETCR1B
Module data bus
Internal
interrupts
Section 7 DMA Controller
7.1.3
Functional Overview
Table 7.1 gives an overview of the DMAC functions.
Table 7.1
DMAC Functional Overview
Transfer Mode
Short
I/O mode
address
• Transfers one byte or one word
mode
per request
• Increments or decrements the memory
address by 1 or 2
• Executes 1 to 65,536 transfers
Idle mode
• Transfers one byte or one word per
request
• Holds the memory address fixed
Full
address
mode
• Executes 1 to 65,536 transfers
Repeat mode
• Transfers one byte or one word per
request
• Increments or decrements the memory
address by 1 or 2
• Executes a specified number (1 to 255)
of transfers, then returns to the initial
state and continues
Normal mode
• Auto-request
 Retains the transfer request
internally
 Executes a specified number(1 to
65,536) of transfers continuously
 Selection of burst mode or cyclesteal mode
• External request
 Transfers one byte or one word per
request
 Executes 1 to 65,536 transfers
Block transfer
• Transfers one block of a specified size
per request
• Executes 1 to 65,536 transfers
• Allows either the source or destination
to be a fixed block area
• Block size can be 1 to 255 bytes or
words
Activation
• Compare match/input
capture A interrupts from 16bit timer channels
0 to 2
• Transmit-data-empty
interrupt from SCI channel 0
•
Address
Reg. Length
DestinaSource
tion
24
8
8
24
•
Conversion-end interrupt
from A/D converter
Receive-data-full interrupt
from SCI channel 0
External request
24
8
•
•
Auto-request
External request
24
24
•
Compare match/ input
24
capture A interrupts from 16bit timer channels 0 to 2
External request
Conversion-end interrupt
from A/D converter
24
•
•
•
Rev. 3.00 Sep 14, 2005 page 205 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.1.4
Input/Output Pins
Table 7.2 lists the DMAC pins.
Table 7.2
DMAC Pins
Channel
Name
0
DMA request 0
Transfer end 0
1
DMA request 1
Transfer end 1
Abbreviation
DREQ0
TEND0
DREQ1
TEND1
Input/
Output
Function
Input
External request for DMAC channel 0
Output
Transfer end on DMAC channel 0
Input
External request for DMAC channel 1
Output
Transfer end on DMAC channel 1
Note: External requests cannot be made to channel A in short address mode.
Rev. 3.00 Sep 14, 2005 page 206 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.1.5
Register Configuration
Table 7.3 lists the DMAC registers.
Table 7.3
DMAC Registers
Channel
Address*
Name
Abbreviation R/W
Initial Value
0
H'FFF20
Memory address register 0AR
MAR0AR
R/W
Undetermined
H'FFF21
Memory address register 0AE
MAR0AE
R/W
Undetermined
H'FFF22
Memory address register 0AH
MAR0AH
R/W
Undetermined
H'FFF23
Memory address register 0AL
MAR0AL
R/W
Undetermined
H'FFF26
I/O address register 0A
IOAR0A
R/W
Undetermined
H'FFF24
Execute transfer count register 0AH ETCR0AH
R/W
Undetermined
H'FFF25
Execute transfer count register 0AL ETCR0AL
R/W
Undetermined
H'FFF27
Data transfer control register 0A
DTCR0A
R/W
H'00
H'FFF28
Memory address register 0BR
MAR0BR
R/W
Undetermined
H'FFF29
Memory address register 0BE
MAR0BE
R/W
Undetermined
H'FFF2A
Memory address register 0BH
MAR0BH
R/W
Undetermined
H'FFF2B
Memory address register 0BL
MAR0BL
R/W
Undetermined
H'FFF2E
I/O address register 0B
IOAR0B
R/W
Undetermined
H'FFF2C
Execute transfer count register 0BH ETCR0BH
R/W
Undetermined
H'FFF2D
Execute transfer count register 0BL ETCR0BL
R/W
Undetermined
H'FFF2F
Data transfer control register 0B
DTCR0B
R/W
H'00
H'FFF30
Memory address register 1AR
MAR1AR
R/W
Undetermined
H'FFF31
Memory address register 1AE
MAR1AE
R/W
Undetermined
H'FFF32
Memory address register 1AH
MAR1AH
R/W
Undetermined
H'FFF33
Memory address register 1AL
MAR1AL
R/W
Undetermined
H'FFF36
I/O address register 1A
IOAR1A
R/W
Undetermined
H'FFF34
Execute transfer count register 1AH ETCR1AH
R/W
Undetermined
H'FFF35
Execute transfer count register 1AL ETCR1AL
R/W
Undetermined
H'FFF37
Data transfer control register 1A
DTCR1A
R/W
H'00
H'FFF38
Memory address register 1BR
MAR1BR
R/W
Undetermined
H'FFF39
Memory address register 1BE
MAR1BE
R/W
Undetermined
H'FFF3A
Memory address register 1BH
MAR1BH
R/W
Undetermined
H'FFF3B
Memory address register 1BL
MAR1BL
R/W
Undetermined
1
Rev. 3.00 Sep 14, 2005 page 207 of 910
REJ09B0258-0300
Section 7 DMA Controller
Channel
Address*
Name
Abbreviation R/W
Initial Value
1
H'FFF3E
I/O address register 1B
IOAR1B
R/W
Undetermined
H'FFF3C
Execute transfer count register 1BH ETCR1BH
R/W
Undetermined
H'FFF3D
Execute transfer count register 1BL ETCR1BL
R/W
Undetermined
H'FFF3F
Data transfer control register 1B
R/W
H'00
DTCR1B
Note: * The lower 20 bits of the address are indicated.
7.2
Register Descriptions (1) (Short Address Mode)
In short address mode, transfers can be carried out independently on channels A and B. Short
address mode is selected by bits DTS2A and DTS1A in data transfer control register A (DTCRA)
as indicated in table 7.4.
Table 7.4
Selection of Short and Full Address Modes
Bit 2
Channel DTS2A
Bit 1
DTS1A
Description
0
1
DMAC channel 0 operates as one channel in full address mode
1
1
Other than above
DMAC channels 0A and 0B operate as two independent channels
in short address mode
1
DMAC channel 1 operates as one channel in full address mode
1
Other than above
7.2.1
DMAC channels 1A and 1B operate as two independent channels
in short address mode
Memory Address Registers (MAR)
A memory address register (MAR) is a 32-bit readable/writable register that specifies a source or
destination address. The transfer direction is determined automatically from the activation source.
An MAR consists of four 8-bit registers designated MARR, MARE, MARH, and MARL. All bits
of MARR are reserved; they cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 208 of 910
REJ09B0258-0300
Section 7 DMA Controller
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
Initial value
Read/Write
8
7
6
5
4
3
2
1
0
Undetermined
— — — — — — — — R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
MARR
MARE
MARH
MARL
Source or destination address
An MAR functions as a source or destination address register depending on how the DMAC is
activated: as a destination address register if activation is by a receive-data-full interrupt from
serial communication interface (SCI) channel 0 or by an A/D converter conversion-end interrupt,
and as a source address register otherwise.
The MAR value is incremented or decremented each time one byte or word is transferred,
automatically updating the source or destination memory address. For details, see section 7.3.4,
Data Transfer Control Registers (DTCR).
The MARs are not initialized by a reset or in standby mode.
7.2.2
I/O Address Registers (IOAR)
An I/O address register (IOAR) is an 8-bit readable/writable register that specifies a source or
destination address. The IOAR value is the lower 8 bits of the address. The upper 16 address bits
are all 1 (H'FFFF).
Bit
7
6
5
Initial value
Read/Write
4
3
2
1
0
R/W
R/W
R/W
Undetermined
R/W
R/W
R/W
R/W
R/W
Source or destination address
An IOAR functions as a source or destination address register depending on how the DMAC is
activated: as a destination address register if activation is by a receive-data-full interrupt from
serial communication interface (SCI) channel 0 or by an A/D converter conversion-end interrupt,
and as a source address register otherwise.
The IOAR value is held fixed. It is not incremented or decremented when a transfer is executed.
The IOARs are not initialized by a reset or in standby mode.
Rev. 3.00 Sep 14, 2005 page 209 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.2.3
Execute Transfer Count Registers (ETCR)
An execute transfer count register (ETCR) is a 16-bit readable/writable register that specifies the
number of transfers to be executed. These registers function in one way in I/O mode and idle
mode, and another way in repeat mode.
• I/O mode and idle mode
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
Undetermined
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Transfer counter
In I/O mode and idle mode, ETCR functions as a 16-bit counter. The count is decremented by
1 each time one transfer is executed. The transfer ends when the count reaches H'0000.
• Repeat mode
Bit
7
6
5
Initial value
Read/Write
4
3
2
1
0
R/W
R/W
R/W
2
1
0
R/W
R/W
R/W
Undetermined
R/W
R/W
R/W
R/W
R/W
ETCRH
Transfer counter
Bit
7
6
5
Initial value
Read/Write
4
3
Undetermined
R/W
R/W
R/W
R/W
R/W
ETCRL
Initial count
In repeat mode, ETCRH functions as an 8-bit transfer counter and ETCRL holds the initial
transfer count. ETCRH is decremented by 1 each time one transfer is executed. When ETCRH
reaches H'00, the value in ETCRL is reloaded into ETCRH and the same operation is repeated.
The ETCRs are not initialized by a reset or in standby mode.
Rev. 3.00 Sep 14, 2005 page 210 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.2.4
Data Transfer Control Registers (DTCR)
A data transfer control register (DTCR) is an 8-bit readable/writable register that controls the
operation of one DMAC channel.
Bit
7
6
5
4
3
2
1
0
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Data transfer enable
Enables or disables
data transfer
Data transfer select
These bits select the data
transfer activation source
Data transfer size
Selects byte or
word size
Data transfer interrupt enable
Enables or disables the CPU interrupt
at the end of the transfer
Data transfer
increment/decrement
Selects whether to
increment or decrement
the memory address
register
Repeat enable
Selects repeat
mode
The DTCRs are initialized to H'00 by a reset and in standby mode.
Bit 7—Data Transfer Enable (DTE): Enables or disables data transfer on a channel. When the
DTE bit is set to 1, the channel waits for a transfer to be requested, and executes the transfer
when activated as specified by bits DTS2 to DTS0. When DTE is 0, the channel is disabled and
does not accept transfer requests. DTE is set to 1 by reading the register when DTE is 0, then
writing 1.
Bit 7
DTE
Description
0
Data transfer is disabled. In I/O mode or idle mode, DTE is cleared to 0 (Initial value)
when the specified number of transfers have been completed
1
Data transfer is enabled
If DTIE is set to 1, a CPU interrupt is requested when DTIE is cleared to 0.
Rev. 3.00 Sep 14, 2005 page 211 of 910
REJ09B0258-0300
Section 7 DMA Controller
Bit 6—Data Transfer Size (DTSZ): Selects the data size of each transfer.
Bit 6
DTSZ
Description
0
Byte-size transfer
1
Word-size transfer
(Initial value)
Bit 5—Data Transfer Increment/Decrement (DTID): Selects whether to increment or
decrement the memory address register (MAR) after a data transfer in I/O mode or repeat mode.
Bit 5
DTID
Description
0
MAR is incremented after each data transfer
1
•
If DTSZ = 0, MAR is incremented by 1 after each transfer
•
If DTSZ = 1, MAR is incremented by 2 after each transfer
(Initial value)
MAR is decremented after each data transfer
•
If DTSZ = 0, MAR is decremented by 1 after each transfer
•
If DTSZ = 1, MAR is decremented by 2 after each transfer
MAR is not incremented or decremented in idle mode.
Bit 4—Repeat Enable (RPE): Selects whether to transfer data in I/O mode, idle mode, or repeat
mode.
Bit 4
RPE
Bit 3
DTIE
Description
0
0
I/O mode
(Initial value)
1
1
0
Repeat mode
1
Idle mode
Operations in these modes are described in sections 7.4.2, I/O Mode, 7.4.3, Idle Mode, and 7.4.4,
Repeat Mode.
Rev. 3.00 Sep 14, 2005 page 212 of 910
REJ09B0258-0300
Section 7 DMA Controller
Bit 3—Data Transfer Interrupt Enable (DTIE): Enables or disables the CPU interrupt
(DEND) requested when the DTE bit is cleared to 0.
Bit 3
DTIE
Description
0
The DEND interrupt requested by DTE is disabled
1
The DEND interrupt requested by DTE is enabled
(Initial value)
Bits 2 to 0—Data Transfer Select (DTS2, DTS1, DTS0): These bits select the data transfer
activation source. Some of the selectable sources differ between channels A and B.
Bit 2
DTS2
Bit 1
DTS1
Bit 0
DTS0
0
0
0
Compare match/input capture A interrupt from 16-bit timer channel 0
(Initial value)
1
Compare match/input capture A interrupt from 16-bit timer channel 1
0
Compare match/input capture A interrupt from 16-bit timer channel 2
1
Conversion-end interrupt from A/D converter
0
Transmit-data-empty interrupt from SCI channel 0
1
Receive-data-full interrupt from SCI channel 0
0
Falling edge of DREQ input (channel B)
Transfer in full address mode (channel A)
1
Low level of DREQ input (channel B)
Transfer in full address mode (channel A)
1
1
0
1
Description
Note: See section 7.3.4, Data Transfer Control Registers (DTCR).
The same internal interrupt can be selected as an activation source for two or more channels at
once. In that case the channels are activated in a priority order, highest-priority channel first. For
the priority order, see section 7.4.9, Multiple-Channel Operation.
When a channel is enabled (DTE = 1), its selected DMAC activation source cannot generate a
CPU interrupt.
Rev. 3.00 Sep 14, 2005 page 213 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.3
Register Descriptions (2) (Full Address Mode)
In full address mode the A and B channels operate together. Full address mode is selected as
indicated in table 7.4.
7.3.1
Memory Address Registers (MAR)
A memory address register (MAR) is a 32-bit readable/writable register. MARA functions as the
source address register of the transfer, and MARB as the destination address register.
An MAR consists of four 8-bit registers designated MARR, MARE, MARH, and MARL. All bits
of MARR are reserved; they cannot be modified and are always read as 1. (Write is invalid.)
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
Initial value
Undetermined
Read/Write
— — — — — — — — R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
MARR
MARE
MARH
MARL
Source or destination address
The MAR value is incremented or decremented each time one byte or word is transferred,
automatically updating the source or destination memory address. For details, see section 7.3.4,
Data Transfer Control Registers (DTCR).
The MARs are not initialized by a reset or in standby mode.
7.3.2
I/O Address Registers (IOAR)
The I/O address registers (IOARs) are not used in full address mode.
Rev. 3.00 Sep 14, 2005 page 214 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.3.3
Execute Transfer Count Registers (ETCR)
An execute transfer count register (ETCR) is a 16-bit readable/writable register that specifies the
number of transfers to be executed. The functions of these registers differ between normal mode
and block transfer mode.
• Normal mode
ETCRA
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
Undetermined
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Transfer counter
ETCRB: Is not used in normal mode.
In normal mode ETCRA functions as a 16-bit transfer counter. The count is decremented by 1
each time one transfer is executed. The transfer ends when the count reaches H'0000. ETCRB is
not used.
Rev. 3.00 Sep 14, 2005 page 215 of 910
REJ09B0258-0300
Section 7 DMA Controller
• Block transfer mode
ETCRA
Bit
7
6
5
4
Initial value
Read/Write
3
2
1
0
R/W
R/W
R/W
2
1
0
R/W
R/W
R/W
Undetermined
R/W
R/W
R/W
R/W
R/W
ETCRAH
Block size counter
Bit
7
6
5
4
Initial value
Read/Write
3
Undetermined
R/W
R/W
R/W
R/W
R/W
ETCRAL
Initial block size
ETCRB
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
Undetermined
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Block transfer counter
In block transfer mode, ETCRAH functions as an 8-bit block size counter. ETCRAL holds the
initial block size. ETCRAH is decremented by 1 each time one byte or word is transferred. When
the count reaches H'00, ETCRAH is reloaded from ETCRAL. Blocks consisting of an arbitrary
number of bytes or words can be transferred repeatedly by setting the same initial block size value
in ETCRAH and ETCRAL.
In block transfer mode ETCRB functions as a 16-bit block transfer counter. ETCRB is
decremented by 1 each time one block is transferred. The transfer ends when the count reaches
H'0000.
The ETCRs are not initialized by a reset or in standby mode.
Rev. 3.00 Sep 14, 2005 page 216 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.3.4
Data Transfer Control Registers (DTCR)
The data transfer control registers (DTCRs) are 8-bit readable/writable registers that control the
operation of the DMAC channels. A channel operates in full address mode when bits DTS2A and
DTS1A are both set to 1 in DTCRA. DTCRA and DTCRB have different functions in full address
mode.
DTCRA
Bit
7
6
5
4
3
2
1
0
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A
DTS1A
DTS0A
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Data transfer enable
Enables or disables
data transfer
Data transfer size
Selects byte or
word size
Data transfer
interrupt enable
Enables or disables the
CPU interrupt at the end
of the transfer
Source address
increment/decrement
Source address increment/
decrement enable
These bits select whether
the source address register
(MARA) is incremented,
decremented, or held fixed
during the data transfer
Data transfer
select 0A
Selects block
transfer mode
Data transfer select
2A and 1A
These bits must both be
set to 1
DTCRA is initialized to H'00 by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 217 of 910
REJ09B0258-0300
Section 7 DMA Controller
Bit 7—Data Transfer Enable (DTE): Together with the DTME bit in DTCRB, this bit enables
or disables data transfer on the channel. When the DTME and DTE bits are both set to 1, the
channel is enabled. If auto-request is specified, data transfer begins immediately. Otherwise, the
channel waits for transfers to be requested. When the specified number of transfers have been
completed, the DTE bit is automatically cleared to 0. When DTE is 0, the channel is disabled and
does not accept transfer requests. DTE is set to 1 by reading the register when DTE is 0, then
writing 1.
Bit 7
DTE
Description
0
Data transfer is disabled (DTE is cleared to 0 when the specified number (Initial value)
of transfers have been completed)
1
Data transfer is enabled
If DTIE is set to 1, a CPU interrupt is requested when DTE is cleared to 0.
Bit 6—Data Transfer Size (DTSZ): Selects the data size of each transfer.
Bit 6
DTSZ
Description
0
Byte-size transfer
1
Word-size transfer
(Initial value)
Bit 5—Source Address Increment/Decrement (SAID) and,
Bit 4—Source Address Increment/Decrement Enable (SAIDE): These bits select whether the
source address register (MARA) is incremented, decremented, or held fixed during the data
transfer.
Bit 5
SAID
Bit 4
SAIDE
Description
0
0
MARA is held fixed
1
MARA is incremented after each data transfer
1
•
If DTSZ = 0, MARA is incremented by 1 after each transfer
•
If DTSZ = 1, MARA is incremented by 2 after each transfer
0
MARA is held fixed
1
MARA is decremented after each data transfer
(Initial value)
•
If DTSZ = 0, MARA is decremented by 1 after each transfer
•
If DTSZ = 1, MARA is decremented by 2 after each transfer
Rev. 3.00 Sep 14, 2005 page 218 of 910
REJ09B0258-0300
Section 7 DMA Controller
Bit 3—Data Transfer Interrupt Enable (DTIE): Enables or disables the CPU interrupt
(DEND) requested when the DTE bit is cleared to 0.
Bit 3
DTIE
Description
0
The DEND interrupt requested by DTE is disabled
1
The DEND interrupt requested by DTE is enabled
(Initial value)
Bits 2 and 1—Data Transfer Select 2A and 1A (DTS2A, DTS1A): A channel operates in full
address mode when DTS2A and DTS1A are both set to 1.
Bit 0—Data Transfer Select 0A (DTS0A): Selects normal mode or block transfer mode.
Bit 0
DTS0A
Description
0
Normal mode
1
Block transfer mode
(Initial value)
Operations in these modes are described in sections 7.4.5, Normal Mode, and 7.4.6, Block
Transfer Mode.
Rev. 3.00 Sep 14, 2005 page 219 of 910
REJ09B0258-0300
Section 7 DMA Controller
DTCRB
Bit
7
6
5
4
3
2
1
0
DTME

DAID
DAIDE
TMS
DTS2B
DTS1B
DTS0B
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Data transfer master enable
Enables or disables data
transfer, together with
the DTE bit, and is cleared
to 0 by an interrupt
Reserved bit
Transfer mode select
Selects whether the
block area is the source
or destination in block
transfer mode
Destination address
increment/decrement
Destination address
increment/decrement enable
These bits select whether
the destination address
register (MARB) is incremented,
decremented, or held fixed
during the data transfer
Data transfer select
2B to 0B
These bits select the data
transfer activation source
DTCRB is initialized to H'00 by a reset and in standby mode.
Bit 7—Data Transfer Master Enable (DTME): Together with the DTE bit in DTCRA, this bit
enables or disables data transfer. When the DTME and DTE bits are both set to 1, the channel is
enabled. When an NMI interrupt occurs DTME is cleared to 0, suspending the transfer so that the
CPU can use the bus. The suspended transfer resumes when DTME is set to 1 again. For further
information on operation in block transfer mode, see section 7.6.6, NMI Interrupts and Block
Transfer Mode.
DTME is set to 1 by reading the register while DTME = 0, then writing 1.
Bit 7
DTME
Description
0
Data transfer is disabled (DTME is cleared to 0 when an NMI interrupt
occurs)
1
Data transfer is enabled
Rev. 3.00 Sep 14, 2005 page 220 of 910
REJ09B0258-0300
(Initial value)
Section 7 DMA Controller
Bit 6—Reserved: Although reserved, this bit can be written and read.
Bit 5—Destination Address Increment/Decrement (DAID) and,
Bit 4—Destination Address Increment/Decrement Enable (DAIDE): These bits select
whether the destination address register (MARB) is incremented, decremented, or held fixed
during the data transfer.
Bit 5
DAID
Bit 4
DAIDE
Description
0
0
MARB is held fixed
1
MARB is incremented after each data transfer
1
(Initial value)
•
If DTSZ = 0, MARB is incremented by 1 after each data transfer
•
If DTSZ = 1, MARB is incremented by 2 after each data transfer
0
MARB is held fixed
1
MARB is decremented after each data transfer
•
If DTSZ = 0, MARB is decremented by 1 after each data transfer
•
If DTSZ = 1, MARB is decremented by 2 after each data transfer
Bit 3—Transfer Mode Select (TMS): Selects whether the source or destination is the block area
in block transfer mode.
Bit 3
TMS
Description
0
Destination is the block area in block transfer mode
1
Source is the block area in block transfer mode
(Initial value)
Rev. 3.00 Sep 14, 2005 page 221 of 910
REJ09B0258-0300
Section 7 DMA Controller
Bits 2 to 0—Data Transfer Select 2B to 0B (DTS2B, DTS1B, DTS0B): These bits select the
data transfer activation source. The selectable activation sources differ between normal mode and
block transfer mode.
Normal mode
Bit 2
DTS2B
Bit 1
DTS1B
Bit 0
DTS0B
Description
0
0
0
Auto-request (burst mode)
1
Cannot be used
0
Auto-request (cycle-steal mode)
1
Cannot be used
0
Cannot be used
1
Cannot be used
0
Falling edge of DREQ
1
1
0
1
1
(Initial value)
Low level input at DREQ
Block transfer mode
Bit 2
Bit 1
Bit 0
DTS2B DTS1B DTS0B Description
0
0
0
Compare match/input capture A interrupt from 16-bit timer channel 0
(Initial value)
1
Compare match/input capture A interrupt from 16-bit timer channel 1
0
Compare match/input capture A interrupt from 16-bit timer channel 2
1
Conversion-end interrupt from A/D converter
0
0
Cannot be used
1
Cannot be used
1
0
Falling edge of DREQ
1
Cannot be used
1
1
The same internal interrupt can be selected to activate two or more channels. The channels are
activated in a priority order, highest priority first. For the priority order, see section 7.4.9,
Multiple-Channel Operation.
Rev. 3.00 Sep 14, 2005 page 222 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4
Operation
7.4.1
Overview
Table 7.5 summarizes the DMAC modes.
Table 7.5
DMAC Modes
Transfer Mode
Short address
mode
Activation
I/O mode
Idle mode
Repeat mode
Notes
Compare match/input
•
capture A interrupt from
16-bit timer channels 0 to 2
Transmit-data-empty
and receive-data-full
interrupts from SCI
channel 0
Up to four channels
can operate
independently
•
Only the B channels
support external requests
•
A and B channels are
paired; up to two
channels are available
Conversion-end interrupt
from A/D converter
External request
Full address
mode
Normal mode
Auto-request
External request
Block transfer mode
Compare match/input
•
capture A interrupt from
16-bit timer channels 0 to 2
Conversion-end interrupt
from A/D converter
Burst mode transfer or
cycle-steal mode transfer
can be selected for autorequests
External request
A summary of operations in these modes follows.
I/O Mode: One byte or word is transferred per request. A designated number of these transfers
are executed. A CPU interrupt can be requested at completion of the designated number of
transfers. One 24-bit address and one 8-bit address are specified. The transfer direction is
determined automatically from the activation source.
Idle Mode: One byte or word is transferred per request. A designated number of these transfers
are executed. A CPU interrupt can be requested at completion of the designated number of
transfers. One 24-bit address and one 8-bit address are specified. The addresses are held fixed.
The transfer direction is determined automatically from the activation source.
Rev. 3.00 Sep 14, 2005 page 223 of 910
REJ09B0258-0300
Section 7 DMA Controller
Repeat Mode: One byte or word is transferred per request. A designated number of these
transfers are executed. When the designated number of transfers are completed, the initial address
and counter value are restored and operation continues. No CPU interrupt is requested. One 24bit address and one 8-bit address are specified. The transfer direction is determined automatically
from the activation source.
Normal Mode
• Auto-request
The DMAC is activated by register setup alone, and continues executing transfers until the
designated number of transfers have been completed. A CPU interrupt can be requested at
completion of the transfers. Both addresses are 24-bit addresses.
 Cycle-steal mode
The bus is released to another bus master after each byte or word is transferred.
 Burst mode
Unless requested by a higher-priority bus master, the bus is not released until the
designated number of transfers have been completed.
• External request
One byte or word is transferred per request. A designated number of these transfers are
executed. A CPU interrupt can be requested at completion of the designated number of
transfers. Both addresses are 24-bit addresses.
Block Transfer Mode: One block of a specified size is transferred per request. A designated
number of block transfers are executed. At the end of each block transfer, one address is restored
to its initial value. When the designated number of blocks have been transferred, a CPU interrupt
can be requested. Both addresses are 24-bit addresses.
Rev. 3.00 Sep 14, 2005 page 224 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.2
I/O Mode
I/O mode can be selected independently for each channel.
One byte or word is transferred at each transfer request in I/O mode. A designated number of
these transfers are executed. One address is specified in the memory address register (MAR), the
other in the I/O address register (IOAR). The direction of transfer is determined automatically
from the activation source. The transfer is from the address specified in IOAR to the address
specified in MAR if activated by an SCI channel 0 receive-data-full interrupt, and from the
address specified in MAR to the address specified in IOAR otherwise.
Table 7.6 indicates the register functions in I/O mode.
Table 7.6
Register Functions in I/O Mode
Function
Activated by
SCI 0 ReceiveData-Full
Other
Interrupt
Activation
Initial Setting
Operation
0
Destination
address
register
Source
address
register
Destination or
source start
address
Incremented or
decremented
once per
transfer
0
Source
address
register
Destination
address
register
Source or
destination
address
Held fixed
0
Transfer counter
Number of
transfers
Decremented
once per
transfer until
H'0000 is
reached and
transfer ends
Register
23
MAR
23
7
All 1s
IOAR
15
ETCR
Legend
MAR: Memory address register
IOAR: I/O address register
ETCR: Execute transfer count register
MAR and IOAR specify the source and destination addresses. MAR specifies a 24-bit source or
destination address, which is incremented or decremented as each byte or word is transferred.
IOAR specifies the lower 8 bits of a fixed address. The upper 16 bits are all 1s. IOAR is not
incremented or decremented.
Rev. 3.00 Sep 14, 2005 page 225 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.2 illustrates how I/O mode operates.
Transfer
Address T
IOAR
1 byte or word is
transferred per request
Address B
Legend
L = initial setting of MAR
N = initial setting of ETCR
Address T = L
Address B = L + (–1) DTID • (2 DTSZ • N – 1)
Figure 7.2 Operation in I/O Mode
The transfer count is specified as a 16-bit value in ETCR. The ETCR value is decremented by 1
at each transfer. When the ETCR value reaches H'0000, the DTE bit is cleared and the transfer
ends. If the DTIE bit is set to 1, a CPU interrupt is requested at this time. The maximum transfer
count is 65,536, obtained by setting ETCR to H'0000.
Transfers can be requested (activated) by compare match/input capture A interrupts from 16-bit
timer channels 0 to 2, transmit-data-empty and receive-data-full interrupts from SCI channel 0,
conversion-end interrupts from the A/D converter, and external request signals.
Rev. 3.00 Sep 14, 2005 page 226 of 910
REJ09B0258-0300
Section 7 DMA Controller
For the detailed settings see section 7.2.4, Data Transfer Control Registers (DTCR).
Figure 7.3 shows a sample setup procedure for I/O mode.
I/O mode setup
Set source and
destination addresses
1
Set transfer count
2
Read DTCR
3
Set DTCR
4
1. Set the source and destination addresses
in MAR and IOAR. The transfer direction is
determined automatically from the activation
source.
2. Set the transfer count in ETCR.
3. Read DTCR while the DTE bit is cleared to 0.
4. Set the DTCR bits as follows.
• Select the DMAC activation source with bits
DTS2 to DTS0.
• Set or clear the DTIE bit to enable or disable
the CPU interrupt at the end of the transfer.
• Clear the RPE bit to 0 to select I/O mode.
• Select MAR increment or decrement with the
DTID bit.
• Select byte size or word size with the DTSZ bit.
• Set the DTE bit to 1 to enable the transfer.
I/O mode
Figure 7.3 I/O Mode Setup Procedure (Example)
7.4.3
Idle Mode
Idle mode can be selected independently for each channel.
One byte or word is transferred at each transfer request in idle mode. A designated number of
these transfers are executed. One address is specified in the memory address register (MAR), the
other in the I/O address register (IOAR). The direction of transfer is determined automatically
from the activation source. The transfer is from the address specified in IOAR to the address
specified in MAR if activated by an SCI channel 0 receive-data-full interrupt, and from the
address specified in MAR to the address specified in IOAR otherwise.
Table 7.7 indicates the register functions in idle mode.
Rev. 3.00 Sep 14, 2005 page 227 of 910
REJ09B0258-0300
Section 7 DMA Controller
Table 7.7
Register Functions in Idle Mode
Function
Activated by
SCI 0 ReceiveData-Full
Other
Interrupt
Activation
Register
23
7
All 1s
Destination
address
register
Source
address
register
Destination or Held fixed
source address
0
Source
address
register
Destination
address
register
Source or
destination
address
Held fixed
0
Transfer counter
Number of
transfers
Decremented
once per
transfer until
H'0000 is
reached and
transfer ends
IOAR
15
Operation
0
MAR
23
Initial Setting
ETCR
Legend
MAR: Memory address register
IOAR: I/O address register
ETCR: Execute transfer count register
MAR and IOAR specify the source and destination addresses. MAR specifies a 24-bit source or
destination address. IOAR specifies the lower 8 bits of a fixed address. The upper 16 bits are all
1s. MAR and IOAR are not incremented or decremented.
Figure 7.4 illustrates how idle mode operates.
Transfer
MAR
1 byte or word is
transferred per request
Figure 7.4 Operation in Idle Mode
Rev. 3.00 Sep 14, 2005 page 228 of 910
REJ09B0258-0300
IOAR
Section 7 DMA Controller
The transfer count is specified as a 16-bit value in ETCR. The ETCR value is decremented by 1
at each transfer. When the ETCR value reaches H'0000, the DTE bit is cleared, the transfer ends,
and a CPU interrupt is requested. The maximum transfer count is 65,536, obtained by setting
ETCR to H'0000.
Transfers can be requested (activated) by compare match/input capture A interrupts from 16-bit
timer channels 0 to 2, transmit-data-empty and receive-data-full interrupts from SCI channel 0,
conversion-end interrupts from the A/D converter, and external request signals.
For the detailed settings see section 7.3.4, Data Transfer Control Registers (DTCR).
Figure 7.5 shows a sample setup procedure for idle mode.
Idle mode setup
Set source and
destination addresses
1
Set transfer count
2
Read DTCR
3
Set DTCR
4
1. Set the source and destination addresses
in MAR and IOAR. The transfer direction is determined automatically from the activation source.
2. Set the transfer count in ETCR.
3. Read DTCR while the DTE bit is cleared to 0.
4. Set the DTCR bits as follows.
• Select the DMAC activation source with bits
DTS2 to DTS0.
• Set the DTIE and RPE bits to 1 to select idle mode.
• Select byte size or word size with the DTSZ bit.
• Set the DTE bit to 1 to enable the transfer.
Idle mode
Figure 7.5 Idle Mode Setup Procedure (Example)
Rev. 3.00 Sep 14, 2005 page 229 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.4
Repeat Mode
Repeat mode is useful for cyclically transferring a bit pattern from a table to the programmable
timing pattern controller (TPC) in synchronization, for example, with 16-bit timer compare
match. Repeat mode can be selected for each channel independently.
One byte or word is transferred per request in repeat mode, as in I/O mode. A designated number
of these transfers are executed. One address is specified in the memory address register (MAR),
the other in the I/O address register (IOAR). At the end of the designated number of transfers,
MAR and ETCRH are restored to their original values and operation continues. The direction of
transfer is determined automatically from the activation source. The transfer is from the address
specified in IOAR to the address specified in MAR if activated by an SCI channel 0 receive-datafull interrupt, and from the address specified in MAR to the address specified in IOAR otherwise.
Table 7.8 indicates the register functions in repeat mode.
Rev. 3.00 Sep 14, 2005 page 230 of 910
REJ09B0258-0300
Section 7 DMA Controller
Table 7.8
Register Functions in Repeat Mode
Function
Register
Activated by
SCI 0 ReceiveData-Full
Other
Interrupt
Activation Initial Setting
23
Destination
address
register
Source
address
register
Source
address
register
Destination Source or
address
destination
register
address
0
Destination or
source start
address
MAR
7
23
All 1s
0
IOAR
7
0
Incremented or
decremented at
each transfer until
ETCRH reaches
H'0000, then restored
to initial value
Held fixed
Transfer counter
Number of
transfers
Decremented once
per transfer until
H'0000 is reached,
then reloaded from
ETCRL
Initial transfer count
Number of
transfers
Held fixed
0
ETCRH
7
Operation
ETCRL
Legend
MAR: Memory address register
IOAR: I/O address register
ETCR: Execute transfer count register
In repeat mode ETCRH is used as the transfer counter while ETCRL holds the initial transfer
count. ETCRH is decremented by 1 at each transfer until it reaches H'00, then is reloaded from
ETCRL. MAR is also restored to its initial value, which is calculated from the DTSZ and DTID
bits in DTCR. Specifically, MAR is restored as follows:
MAR ← MAR – (–1)DTID · 2DTSZ · ETCRL
ETCRH and ETCRL should be initially set to the same value.
In repeat mode transfers continue until the CPU clears the DTE bit to 0. After DTE is cleared to
0, if the CPU sets DTE to 1 again, transfers resume from the state at which DTE was cleared. No
CPU interrupt is requested.
Rev. 3.00 Sep 14, 2005 page 231 of 910
REJ09B0258-0300
Section 7 DMA Controller
As in I/O mode, MAR and IOAR specify the source and destination addresses. MAR specifies a
24-bit source or destination address. IOAR specifies the lower 8 bits of a fixed address. The
upper 16 bits are all 1s. IOAR is not incremented or decremented.
Figure 7.6 illustrates how repeat mode operates.
Transfer
Address T
IOAR
1 byte or word is
transferred per request
Legend
L = initial setting of MAR
N = initial setting of ETCRH and ETCRL
Address T = L
Address B = L + (–1) DTID • (2DTSZ • N – 1)
Address B
Figure 7.6 Operation in Repeat Mode
The transfer count is specified as an 8-bit value in ETCRH and ETCRL. The maximum transfer
count is 255, obtained by setting both ETCRH and ETCRL to H'FF.
Transfers can be requested (activated) by compare match/input capture A interrupts from 16-bit
timer channels 0 to 2, transmit-data-empty and receive-data-full interrupts from SCI channel 0,
conversion-end interrupts from the A/D converter, and external request signals.
For the detailed settings see section 7.2.4, Data Transfer Control Registers (DTCR).
Figure 7.7 shows a sample setup procedure for repeat mode.
Rev. 3.00 Sep 14, 2005 page 232 of 910
REJ09B0258-0300
Section 7 DMA Controller
Repeat mode
Set source and
destination addresses
1
Set transfer count
2
Read DTCR
3
Set DTCR
4
1. Set the source and destination addresses in MAR
and IOAR. The transfer direction is determined
automatically from the activation source.
2. Set the transfer count in both ETCRH and ETCRL.
3. Read DTCR while the DTE bit is cleared to 0.
4. Set the DTCR bits as follows.
• Select the DMAC activation source with bits
DTS2 to DTS0.
• Clear the DTIE bit to 0 and set the RPE bit to 1
to select repeat mode.
• Select MAR increment or decrement with the DTID bit.
• Select byte size or word size with the DTSZ bit.
• Set the DTE bit to 1 to enable the transfer.
Repeat mode
Figure 7.7 Repeat Mode Setup Procedure (Example)
Rev. 3.00 Sep 14, 2005 page 233 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.5
Normal Mode
In normal mode the A and B channels are combined. One byte or word is transferred per request.
A designated number of these transfers are executed. Addresses are specified in MARA and
MARB. Table 7.9 indicates the register functions in I/O mode.
Table 7.9
Register Functions in Normal Mode
Register
Function
Initial Setting
Operation
MARA
0 Source address
register
Source start
address
Incremented or
decremented once per
transfer, or held fixed
MARB
0 Destination
address register
Destination start
address
Incremented or
decremented once per
transfer, or held fixed
0 Transfer counter
Number of
transfers
Decremented once per
transfer
23
23
15
ETCRA
Legend
MARA: Memory address register A
MARB: Memory address register B
ETCRA: Execute transfer count register A
The source and destination addresses are both 24-bit addresses. MARA specifies the source
address. MARB specifies the destination address. MARA and MARB can be independently
incremented, decremented, or held fixed as data is transferred.
The transfer count is specified as a 16-bit value in ETCRA. The ETCRA value is decremented by
1 at each transfer. When the ETCRA value reaches H'0000, the DTE bit is cleared and the
transfer ends. If the DTIE bit is set to 1, a CPU interrupt is requested at this time. The maximum
transfer count is 65,536, obtained by setting ETCRA to H'0000.
Rev. 3.00 Sep 14, 2005 page 234 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.8 illustrates how normal mode operates.
Transfer
Address TA
Address T B
Address BA
Address B B
Legend
L A = initial setting of MARA
L B = initial setting of MARB
N = initial setting of ETCRA
TA = LA
BA = L A + SAIDE • (–1)SAID • (2 DTSZ • N – 1)
TB = LB
BB = L B + DAIDE • (–1)DAID • (2DTSZ • N – 1)
Figure 7.8 Operation in Normal Mode
Transfers can be requested (activated) by an external request or auto-request. An auto-requested
transfer is activated by the register settings alone. The designated number of transfers are
executed automatically. Either cycle-steal or burst mode can be selected. In cycle-steal mode the
DMAC releases the bus temporarily after each transfer. In burst mode the DMAC keeps the bus
until the transfers are completed, unless there is a bus request from a higher-priority bus master.
For the detailed settings see section 7.3.4, Data Transfer Control Registers (DTCR).
Rev. 3.00 Sep 14, 2005 page 235 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.9 shows a sample setup procedure for normal mode.
Normal mode
Set initial source address
1
Set initial destination address
2
1.
2.
3.
4.
5.
Set transfer count
3
Set DTCRB (1)
4
Set DTCRA (1)
5
Read DTCRB
6
Set DTCRB (2)
7
Read DTCRA
8
Set DTCRA (2)
9
6.
7.
8.
9.
Set the initial source address in MARA.
Set the initial destination address in MARB.
Set the transfer count in ETCRA.
Set the DTCRB bits as follows.
• Clear the DTME bit to 0.
• Set the DAID and DAIDE bits to select whether
MARB is incremented, decremented, or held fixed.
• Select the DMAC activation source with bits
DTS2B to DTS0B.
Set the DTCRA bits as follows.
• Clear the DTE bit to 0.
• Select byte or word size with the DTSZ bit.
• Set the SAID and SAIDE bits to select whether
MARA is incremented, decremented, or held fixed.
• Set or clear the DTIE bit to enable or disable the
CPU interrupt at the end of the transfer.
• Clear the DTS0A bit to 0 and set the DTS2A
and DTS1A bits to 1 to select normal mode.
Read DTCRB with DTME cleared to 0.
Set the DTME bit to 1 in DTCRB.
Read DTCRA with DTE cleared to 0.
Set the DTE bit to 1 in DTCRA to enable the transfer.
Normal mode
Note: Carry out settings 1 to 9 with the DEND interrupt masked in the CPU.
If an NMI interrupt occurs during the setup procedure, it may clear the DTME bit to 0, in
which case the transfer will not start.
Figure 7.9 Normal Mode Setup Procedure (Example)
Rev. 3.00 Sep 14, 2005 page 236 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.6
Block Transfer Mode
In block transfer mode the A and B channels are combined. One block of a specified size is
transferred per request. A designated number of block transfers are executed. Addresses are
specified in MARA and MARB. The block area address can be either held fixed or cycled.
Table 7.10 indicates the register functions in block transfer mode.
Table 7.10 Register Functions in Block Transfer Mode
Register
Function
Initial Setting
Operation
23
0
Source address
register
Source start
address
Incremented or
decremented once per
transfer, or held fixed
0
Destination
address register
Destination start
address
Incremented or
decremented once per
transfer, or held fixed
0
Block size counter
Block size
Decremented once per
transfer until H'00 is
reached, then reloaded
from ETCRL
Initial block size
Block size
Held fixed
Block transfer
counter
Number of block
transfers
Decremented once per
block transfer until H'0000
is reached and the
transfer ends
MARA
23
MARB
7
ETCRAH
7
0
ETCRAL
15
0
ETCRB
Legend
MARA: Memory address register A
MARB: Memory address register B
ETCRA: Execute transfer count register A
ETCRB: Execute transfer count register B
The source and destination addresses are both 24-bit addresses. MARA specifies the source
address. MARB specifies the destination address. MARA and MARB can be independently
incremented, decremented, or held fixed as data is transferred. One of these registers operates as
a block area register: even if it is incremented or decremented, it is restored to its initial value at
the end of each block transfer. The TMS bit in DTCRB selects whether the block area is the
source or destination.
Rev. 3.00 Sep 14, 2005 page 237 of 910
REJ09B0258-0300
Section 7 DMA Controller
If M (1 to 255) is the size of the block transferred at each request and N (1 to 65,536) is the
number of blocks to be transferred, then ETCRAH and ETCRAL should initially be set to M and
ETCRB should initially be set to N.
Figure 7.10 illustrates how block transfer mode operates. In this figure, bit TMS is cleared to 0,
meaning the block area is the destination.
TA
Address T B
Transfer
Block 1
Block area
BA
Address B B
Block 2
M bytes or words are
transferred per request
Block N
Legend
L A = initial setting of MARA
L B = initial setting of MARB
M = initial setting of ETCRAH and ETCRAL
N = initial setting of ETCRB
T A = LA
B A = L A + SAIDE • (–1)SAID • (2 DTSZ • M – 1)
T B = LB
B B = L B + DAIDE • (–1)DAID • (2DTSZ • M – 1)
Figure 7.10 Operation in Block Transfer Mode
Rev. 3.00 Sep 14, 2005 page 238 of 910
REJ09B0258-0300
Section 7 DMA Controller
When activated by a transfer request, the DMAC executes a burst transfer. During the transfer
MARA and MARB are updated according to the DTCR settings, and ETCRAH is decremented.
When ETCRAH reaches H'00, it is reloaded from ETCRAL to restore the initial value. The
memory address register of the block area is also restored to its initial value, and ETCRB is
decremented. If ETCRB is not H'0000, the DMAC then waits for the next transfer request.
ETCRAH and ETCRAL should be initially set to the same value.
The above operation is repeated until ETCRB reaches H'0000, at which point the DTE bit is
cleared to 0 and the transfer ends. If the DTIE bit is set to 1, a CPU interrupt is requested at this
time.
Figure 7.11 shows examples of a block transfer with byte data size when the block area is the
destination. In (a) the block area address is cycled. In (b) the block area address is held fixed.
Transfers can be requested (activated) by compare match/input capture A interrupts from ITU
channels 0 to 2, by an A/D converter conversion-end interrupt, and by external request signals.
For the detailed settings see section 7.3.4, Data Transfer Control Registers (DTCR).
Rev. 3.00 Sep 14, 2005 page 239 of 910
REJ09B0258-0300
Section 7 DMA Controller
Start
(DTE = DTME = 1)
Transfer requested?
Start
(DTE = DTME = 1)
No
Transfer requested?
Yes
No
Yes
Get bus
Get bus
Read from MARA address
Read from MARA address
MARA = MARA + 1
MARA = MARA + 1
Write to MARB address
Write to MARB address
MARB = MARB + 1
ETCRAH = ETCRAH – 1
ETCRAH = ETCRAH – 1
No
ETCRAH = H'00
No
ETCRAH = H'00
Yes
Yes
Release bus
Release bus
ETCRAH = ETCRAL
MARB = MARB – ETCRAL
ETCRAH = ETCRAL
ETCRB = ETCRB – 1
ETCRB = ETCRB – 1
ETCRB = H'0000
No
ETCRB = H'0000
Yes
Yes
Clear DTE to 0 and end transfer
Clear DTE to 0 and end transfer
a. DTSZ = TMS = 0
SAID = DAID = 0
SAIDE = DAIDE = 1
b. DTSZ = TMS = 0
SAID = 0
SAIDE = 1
DAIDE = 0
Figure 7.11 Block Transfer Mode Flowcharts (Examples)
Rev. 3.00 Sep 14, 2005 page 240 of 910
REJ09B0258-0300
No
Section 7 DMA Controller
Figure 7.12 shows a sample setup procedure for block transfer mode.
Block transfer mode
Set source address
1
Set destination address
2
Set block transfer count
3
Set block size
4
Set DTCRB (1)
5
Set DTCRA (1)
6
Read DTCRB
7
Set DTCRB (2)
8
Read DTCRA
9
Set DTCRA (2)
10
Set the source address in MARA.
Set the destination address in MARB.
Set the block transfer count in ETCRB.
Set the block size (number of bytes or words)
in both ETCRAH and ETCRAL.
5. Set the DTCRB bits as follows.
• Clear the DTME bit to 0.
• Set the DAID and DAIDE bits to select whether
MARB is incremented, decremented, or held fixed.
• Set or clear the TMS bit to make the block area
the source or destination.
• Select the DMAC activation source with bits
DTS2B to DTS0B.
6. Set the DTCRA bits as follows.
• Clear the DTE to 0.
• Select byte size or word size with the DTSZ bit.
• Set the SAID and SAIDE bits to select whether
MARA is incremented, decremented, or held fixed.
• Set or clear the DTIE bit to enable or disable the
CPU interrupt at the end of the transfer.
• Set bits DTS2A to DTS0A all to 1 to select
block transfer mode.
7. Read DTCRB with DTME cleared to 0.
8. Set the DTME bit to 1 in DTCRB.
9. Read DTCRA with DTE cleared to 0.
10. Set the DTE bit to 1 in DTCRA to enable
the transfer.
1.
2.
3.
4.
Block transfer mode
Note: Carry out settings 1 to 10 with the DEND interrupt masked in the CPU.
If an NMI interrupt occurs during the setup procedure, it may clear the DTME bit to 0, in
which case the transfer will not start.
Figure 7.12 Block Transfer Mode Setup Procedure (Example)
Rev. 3.00 Sep 14, 2005 page 241 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.7
DMAC Activation
The DMAC can be activated by an internal interrupt, external request, or auto-request. The
available activation sources differ depending on the transfer mode and channel as indicated in
table 7.11.
Table 7.11 DMAC Activation Sources
Short Address Mode
Activation Source
Internal
interrupts
External
requests
Channels
0A and 1A
0B and 1B
Full Address Mode
Normal
Block
IMIA0
×
IMIA1
×
IMIA2
×
ADI
×
TXI0
×
×
RXI0
×
×
Falling edge
of DREQ
×
Low input at
×
DREQ
Auto-request
Channels
×
×
×
×
Activation by Internal Interrupts: When an interrupt request is selected as a DMAC activation
source and the DTE bit is set to 1, that interrupt request is not sent to the CPU. It is not possible
for an interrupt request to activate the DMAC and simultaneously generate a CPU interrupt.
When the DMAC is activated by an interrupt request, the interrupt request flag is cleared
automatically. If the same interrupt is selected to activate two or more channels, the interrupt
request flag is cleared when the highest-priority channel is activated, but the transfer request is
held pending on the other channels in the DMAC, which are activated in their priority order.
Rev. 3.00 Sep 14, 2005 page 242 of 910
REJ09B0258-0300
Section 7 DMA Controller
Activation by External Request: If an external request (DREQ pin) is selected as an activation
source, the DREQ pin becomes an input pin and the corresponding TEND pin becomes an output
pin, regardless of the port data direction register (DDR) settings. The DREQ input can be levelsensitive or edge-sensitive.
In short address mode and normal mode, an external request operates as follows. If edge sensing
is selected, one byte or word is transferred each time a high-to-low transition of the DREQ input
is detected. If the next edge is input before the transfer is completed, the next transfer may not be
executed. If level sensing is selected, the transfer continues while DREQ is low, until the transfer
is completed. The bus is released temporarily after each byte or word has been transferred,
however. If the DREQ input goes high during a transfer, the transfer is suspended after the
current byte or word has been transferred. When DREQ goes low, the request is held internally
until one byte or word has been transferred. The TEND signal goes low during the last write
cycle.
In block transfer mode, an external request operates as follows. Only edge-sensitive transfer
requests are possible in block transfer mode. Each time a high-to-low transition of the DREQ
input is detected, a block of the specified size is transferred. The TEND signal goes low during
the last write cycle in each block.
Activation by Auto-Request: The transfer starts as soon as enabled by register setup, and
continues until completed. Cycle-steal mode or burst mode can be selected.
In cycle-steal mode the DMAC releases the bus temporarily after transferring each byte or word.
Normally, DMAC cycles alternate with CPU cycles.
In burst mode the DMAC keeps the bus until the transfer is completed, unless there is a higherpriority bus request. If there is a higher-priority bus request, the bus is released after the current
byte or word has been transferred.
Rev. 3.00 Sep 14, 2005 page 243 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.8
DMAC Bus Cycle
Figure 7.13 shows an example of the timing of the basic DMAC bus cycle. This example shows a
word-size transfer from a 16-bit two-state access area to an 8-bit three-state access area. When
the DMAC gets the bus from the CPU, after one dead cycle (Td), it reads from the source address
and writes to the destination address. During these read and write operations the bus is not
released even if there is another bus request. DMAC cycles comply with bus controller settings in
the same way as CPU cycles.
CPU cycle
T1
T2
T1
DMAC cycle (1 word transfer)
T2
Td
T1
T2
T1
T2
T3
T1
T2
CPU cycle
T3
φ
Source
address
Destination address
Address
bus
RD
HWR
LWR
Figure 7.13 DMA Transfer Bus Timing (Example)
Rev. 3.00 Sep 14, 2005 page 244 of 910
REJ09B0258-0300
T1
T2
T1
T2
Section 7 DMA Controller
Figure 7.14 shows the timing when the DMAC is activated by low input at a DREQ pin. This
example shows a word-size transfer from a 16-bit two-state access area to another 16-bit twostate access area. The DMAC continues the transfer while the DREQ pin is held low.
CPU cycle
T1
T2
T3
DMAC cycle
Td
T1
T2
T1
DMAC cycle
(last transfer cycle)
CPU cycle
T2
T1
T2
Td
T1
T2
T1
T2
CPU cycle
T1
T2
φ
DREQ
Source Destination
address address
Source Destination
address address
Address
bus
RD
HWR , LWR
TEND
Figure 7.14 Bus Timing of DMA Transfer Requested by Low DREQ Input
Rev. 3.00 Sep 14, 2005 page 245 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.15 shows an auto-requested burst-mode transfer. This example shows a transfer of three
words from a 16-bit two-state access area to another 16-bit two-state access area.
CPU cycle
T1
T2
CPU cycle
DMAC cycle
Td
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
φ
Source
address
Destination
address
Address
bus
RD
HWR ,
LWR
Figure 7.15 Burst DMA Bus Timing
When the DMAC is activated from a DREQ pin there is a minimum interval of four states from
when the transfer is requested until the DMAC starts operating. The DREQ pin is not sampled
during the time between the transfer request and the start of the transfer. In short address mode
and normal mode, the pin is next sampled at the end of the read cycle. In block transfer mode, the
pin is next sampled at the end of one block transfer.
Rev. 3.00 Sep 14, 2005 page 246 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.16 shows the timing when the DMAC is activated by the falling edge of DREQ in normal
mode.
CPU cycle
T2
T1
T2
T1
CPU
cycle
DMAC cycle
T2
Td
T1
T2
T1
T2
T1
T2
DMAC cycle
Td
T1
T2
φ
DREQ
Address
bus
RD
HWR , LWR
Minimum 4 states
Next sampling point
Figure 7.16 Timing of DMAC Activation by Falling Edge of DREQ in Normal Mode
Rev. 3.00 Sep 14, 2005 page 247 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.17 shows the timing when the DMAC is activated by level-sensitive low DREQ input in
normal mode.
CPU cycle
T2
T1
T2
T1
DMAC cycle
T2
Td
T1
T2
T1
CPU cycle
T2
T1
T2
T1
T2
T1
φ
DREQ
Address
bus
RD
HWR , LWR
Minimum 4 states
Next sampling point
Figure 7.17 Timing of DMAC Activation by Low DREQ Level in Normal Mode
Rev. 3.00 Sep 14, 2005 page 248 of 910
REJ09B0258-0300
Section 7 DMA Controller
Figure 7.18 shows the timing when the DMAC is activated by the falling edge of DREQ in block
transfer mode.
End of 1 block transfer
DMAC cycle
T1
T2
T1
T2
T1
CPU cycle
T2
T1
T2
T1
T2
T1
T2
DMAC cycle
Td
T1
T2
φ
DREQ
Address
bus
RD
HWR , LWR
TEND
Next sampling
Minimum 4 states
Figure 7.18 Timing of DMAC Activation by Falling Edge of DREQ in Block Transfer
Mode
Rev. 3.00 Sep 14, 2005 page 249 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.9
Multiple-Channel Operation
The DMAC channel priority order is: channel 0 > channel 1 and channel A > channel B.
Table 7.12 shows the complete priority order.
Table 7.12 Channel Priority Order
Short Address Mode
Full Address Mode
Priority
Channel 0A
Channel 0
High
Channel 0B
Channel 1A
Channel 1
Channel 1B
Low
If transfers are requested on two or more channels simultaneously, or if a transfer on one channel
is requested during a transfer on another channel, the DMAC operates as follows.
• When a transfer is requested, the DMAC requests the bus right. When it gets the bus right, it
starts a transfer on the highest-priority channel at that time.
• Once a transfer starts on one channel, requests to other channels are held pending until that
channel releases the bus.
• After each transfer in short address mode, and each externally-requested or cycle-steal
transfer in normal mode, the DMAC releases the bus and returns to step 1. After releasing the
bus, if there is a transfer request for another channel, the DMAC requests the bus again.
• After completion of a burst-mode transfer, or after transfer of one block in block transfer
mode, the DMAC releases the bus and returns to step 1. If there is a transfer request for a
higher-priority channel or a bus request from a higher-priority bus master, however, the
DMAC releases the bus after completing the transfer of the current byte or word. After
releasing the bus, if there is a transfer request for another channel, the DMAC requests the
bus again.
Figure 7.19 shows the timing when channel 0A is set up for I/O mode and channel 1 for burst
mode, and a transfer request for channel 0A is received while channel 1 is active.
Rev. 3.00 Sep 14, 2005 page 250 of 910
REJ09B0258-0300
Section 7 DMA Controller
DMAC cycle
(channel 1)
T1
CPU
cycle
T2
T1
T2
DMAC cycle
(channel 0A)
Td
T1
T2
T1
CPU
cycle
T2
T1
T2
DMAC cycle
(channel 1)
Td
T1
T2
T1
T2
φ
Address
bus
RD
HWR ,
LWR
Figure 7.19 Timing of Multiple-Channel Operations
7.4.10
External Bus Requests, DRAM Interface, and DMAC
During a DMAC transfer, if the bus right is requested by an external bus request signal (BREQ)
or by the DRAM interface (refresh cycle), the DMAC releases the bus after completing the
transfer of the current byte or word. If there is a transfer request at this point, the DMAC requests
the bus right again. Figure 7.20 shows an example of the timing of insertion of a refresh cycle
during a burst transfer on channel 0.
Refresh
cycle
DMAC cycle (channel 0)
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
DMAC cycle (channel 0)
Td
T1
T2
T1
T2
T1
T2
φ
Address
bus
RD
HWR , LWR
Figure 7.20 Bus Timing of DRAM Interface, and DMAC
Rev. 3.00 Sep 14, 2005 page 251 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.11
NMI Interrupts and DMAC
NMI interrupts do not affect DMAC operations in short address mode.
If an NMI interrupt occurs during a transfer in full address mode, the DMAC suspends
operations. In full address mode, a channel is enabled when its DTE and DTME bits are both set
to 1. NMI input clears the DTME bit to 0. After transferring the current byte or word, the DMAC
releases the bus to the CPU. In normal mode, the suspended transfer resumes when the CPU sets
the DTME bit to 1 again. Check that the DTE bit is set to 1 and the DTME bit is cleared to 0
before setting the DTME bit to 1.
Figure 7.21 shows the procedure for resuming a DMAC transfer in normal mode on channel 0
after the transfer was halted by NMI input.
Resuming DMAC transfer
in normal mode
1. Check that DTE = 1 and DTME = 0.
2. Read DTCRB while DTME = 0,
then write 1 in the DTME bit.
1
DTE = 1
DTME = 0
No
Yes
Set DTME to 1
2
DMA transfer continues
End
Figure 7.21 Procedure for Resuming a DMAC Transfer Halted by NMI (Example)
For information about NMI interrupts in block transfer mode, see section 7.6.6, NMI Interrupts
and Block Transfer Mode.
Rev. 3.00 Sep 14, 2005 page 252 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.12
Aborting a DMAC Transfer
When the DTE bit in an active channel is cleared to 0, the DMAC halts after transferring the
current byte or word. The DMAC starts again when the DTE bit is set to 1. In full address mode,
the DTME bit can be used for the same purpose. Figure 7.22 shows the procedure for aborting a
DMAC transfer by software.
DMAC transfer abort
Set DTCR
1. Clear the DTE bit to 0 in DTCR.
To avoid generating an interrupt when
aborting a DMA transfer, clear the DTIE
bit to 0 simultaneously.
1
DMAC transfer aborted
Figure 7.22 Procedure for Aborting a DMAC Transfer
Rev. 3.00 Sep 14, 2005 page 253 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.13
Exiting Full Address Mode
Figure 7.23 shows the procedure for exiting full address mode and initializing the pair of
channels. To set the channels up in another mode after exiting full address mode, follow the setup
procedure for the relevant mode.
Exiting full address mode
Halt the channel
1
Initialize DTCRB
2
Initialize DTCRA
3
1. Clear the DTE bit to 0 in DTCRA, or wait
for the transfer to end and the DTE bit
to be cleared to 0.
2. Clear all DTCRB bits to 0.
3. Clear all DTCRA bits to 0.
Initialized and halted
Figure 7.23 Procedure for Exiting Full Address Mode (Example)
Rev. 3.00 Sep 14, 2005 page 254 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.4.14
DMAC States in Reset State, Standby Modes, and Sleep Mode
When the chip is reset or enters software standby mode, the DMAC is initialized and halts.
DMAC operations continue in sleep mode. Figure 7.24 shows the timing of a cycle-steal transfer
in sleep mode.
Sleep mode
CPU cycle
T2
DMAC cycle
Td
T1
T2
T1
DMAC cycle
T2
Td
T1
T2
T1
T2
Td
φ
Address bus
RD
HWR , LWR
Figure 7.24 Timing of Cycle-Steal Transfer in Sleep Mode
Rev. 3.00 Sep 14, 2005 page 255 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.5
Interrupts
The DMAC generates only DMA-end interrupts. Table 7.13 lists the interrupts and their priority.
Table 7.13 DMAC Interrupts
Description
Interrupt
Short Address Mode
Full Address Mode
Interrupt Priority
DEND0A
End of transfer on channel 0A
End of transfer on channel 0
High
DEND0B
End of transfer on channel 0B
—
DEND1A
End of transfer on channel 1A
End of transfer on channel 1
DEND1B
End of transfer on channel 1B
—
Low
Each interrupt is enabled or disabled by the DTIE bit in the corresponding data transfer control
register (DTCR). Separate interrupt signals are sent to the interrupt controller.
The interrupt priority order among channels is channel 0 > channel 1 and channel A > channel B.
Figure 7.25 shows the DMA-end interrupt logic. An interrupt is requested whenever DTE = 0 and
DTIE = 1.
DTE
DMA-end interrupt
DTIE
Figure 7.25 DMA-End Interrupt Logic
The DMA-end interrupt for the B channels (DENDB) is unavailable in full address mode. The
DTME bit does not affect interrupt operations.
Rev. 3.00 Sep 14, 2005 page 256 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.6
Usage Notes
7.6.1
Note on Word Data Transfer
Word data cannot be accessed starting at an odd address. When word-size transfer is selected, set
even values in the memory and I/O address registers (MAR and IOAR).
7.6.2
DMAC Self-Access
The DMAC itself cannot be accessed during a DMAC cycle. DMAC registers cannot be specified
as source or destination addresses.
7.6.3
Longword Access to Memory Address Registers
A memory address register can be accessed as longword data at the MARR address.
Example
MOV.L
#LBL, ER0
MOV.L
ER0, @MARR
Four byte accesses are performed. Note that the CPU may release the bus between the second
byte (MARE) and third byte (MARH).
Memory address registers should be written and read only when the DMAC is halted.
7.6.4
Note on Full Address Mode Setup
Full address mode is controlled by two registers: DTCRA and DTCRB. Care must be taken to
prevent the B channel from operating in short address mode during the register setup. The enable
bits (DTE and DTME) should not be set to 1 until the end of the setup procedure.
Rev. 3.00 Sep 14, 2005 page 257 of 910
REJ09B0258-0300
Section 7 DMA Controller
7.6.5
Note on Activating DMAC by Internal Interrupts
When using an internal interrupt to activate the DMAC, make sure that the interrupt selected as
the activating source does not occur during the interval after it has been selected but before the
DMAC has been enabled. The on-chip supporting module that will generate the interrupt should
not be activated until the DMAC has been enabled. If the DMAC must be enabled while the onchip supporting module is active, follow the procedure in figure 7.26.
Enabling of DMAC
Yes
Interrupt handling by CPU
Selected interrupt
requested?
1
No
Clear selected interrupt's
enable bit to 0
2
Enable DMAC
3
Set selected interrupt's
enable bit to 1
4
1. While the DTE bit is cleared to 0,
interrupt requests are sent to the
CPU.
2. Clear the interrupt enable bit to 0
in the interrupt-generating on-chip
supporting module.
3. Enable the DMAC.
4. Enable the DMAC-activating
interrupt.
DMAC operates
Figure 7.26 Procedure for Enabling DMAC while On-Chip Supporting
Module is Operating (Example)
If the DTE bit is set to 1 but the DTME bit is cleared to 0, the DMAC is halted and the selected
activating source cannot generate a CPU interrupt. If the DMAC is halted by an NMI interrupt,
for example, the selected activating source cannot generate CPU interrupts. To terminate DMAC
operations in this state, clear the DTE bit to 0 to allow CPU interrupts to be requested. To
continue DMAC operations, carry out steps 2 and 4 in figure 7.26 before and after setting the
DTME bit to 1.
Rev. 3.00 Sep 14, 2005 page 258 of 910
REJ09B0258-0300
Section 7 DMA Controller
When 16-bit timer interrupt activates the DMAC, make sure the next interrupt does not occur
before the DMA transfer ends. If one 16-bit timer interrupt activates two or more channels, make
sure the next interrupt does not occur before the DMA transfers end on all the activated channels.
If the next interrupt occurs before a transfer ends, the channel or channels for which that interrupt
was selected may fail to accept further activation requests.
7.6.6
NMI Interrupts and Block Transfer Mode
If an NMI interrupt occurs in block transfer mode, the DMAC operates as follows.
• When the NMI interrupt occurs, the DMAC finishes transferring the current byte or word,
then clears the DTME bit to 0 and halts. The halt may occur in the middle of a block.
It is possible to find whether a transfer was halted in the middle of a block by checking the
block size counter. If the block size counter does not have its initial value, the transfer was
halted in the middle of a block.
• If the transfer is halted in the middle of a block, the activating interrupt flag is cleared to 0.
The activation request is not held pending.
• While the DTE bit is set to 1 and the DTME bit is cleared to 0, the DMAC is halted and does
not accept activating interrupt requests. If an activating interrupt occurs in this state, the
DMAC does not operate and does not hold the transfer request pending internally. Neither is a
CPU interrupt requested.
For this reason, before setting the DTME bit to 1, first clear the enable bit of the activating
interrupt to 0. Then, after setting the DTME bit to 1, set the interrupt enable bit to 1 again. See
section 7.6.5, Note on Activating DMAC by Internal Interrupts.
• When the DTME bit is set to 1, the DMAC waits for the next transfer request. If it was halted
in the middle of a block transfer, the rest of the block is transferred when the next transfer
request occurs. Otherwise, the next block is transferred when the next transfer request occurs.
7.6.7
Memory and I/O Address Register Values
Table 7.14 indicates the address ranges that can be specified in the memory and I/O address
registers (MAR and IOAR).
Rev. 3.00 Sep 14, 2005 page 259 of 910
REJ09B0258-0300
Section 7 DMA Controller
Table 7.14 Address Ranges Specifiable in MAR and IOAR
1-Mbyte Mode
16-Mbyte Mode
MAR
H'00000 to H'FFFFF
(0 to 1048575)
H'000000 to H'FFFFFF
(0 to 16777215)
IOAR
H'FFF00 to H'FFFFF
(1048320 to 1048575)
H'FFFF00 to H'FFFFFF
(16776960 to 16777215)
MAR bits 23 to 20 are ignored in 1-Mbyte mode.
7.6.8
Bus Cycle when Transfer is Aborted
When a transfer is aborted by clearing the DTE bit or suspended by an NMI that clears the
DTME bit, if this halts a channel for which the DMAC has a transfer request pending internally, a
dead cycle may occur. This dead cycle does not update the halted channel’s address register or
counter value. Figure 7.27 shows an example in which an auto-requested transfer in cycle-steal
mode on channel 0 is aborted by clearing the DTE bit in channel 0.
CPU cycle
T1
T2
DMAC cycle
Td
T1
T2
T1
DMAC
cycle
CPU cycle
T2
T1
T2
T3
Td
Td
CPU cycle
T1
φ
Address bus
RD
HWR, LWR
DTE bit is
cleared
Figure 7.27 Bus Timing at Abort of DMA Transfer in Cycle-Steal Mode
Rev. 3.00 Sep 14, 2005 page 260 of 910
REJ09B0258-0300
T2
Section 7 DMA Controller
7.6.9
Transfer Requests by A/D Converter
When the A/D converter is set to scan mode and conversion is performed on more than one
channel, the A/D converter generates a transfer request when all conversions are completed. The
converted data is stored in the appropriate ADDR registers. Block transfer mode and full address
mode should therefore be used to transfer all the conversion results at one time.
Rev. 3.00 Sep 14, 2005 page 261 of 910
REJ09B0258-0300
Section 7 DMA Controller
Rev. 3.00 Sep 14, 2005 page 262 of 910
REJ09B0258-0300
Section 8 I/O Ports
Section 8 I/O Ports
8.1
Overview
The H8/3068F has 11 input/output ports (ports 1, 2, 3, 4, 5, 6, 7, 8, 9, A, and B). Table 8.1
summarizes the port functions. The pins in each port are multiplexed as shown in table 8.1.
Each port has a data direction register (DDR) for selecting input or output, and a data register
(DR) for storing output data. In addition to these registers, ports 2, 4, and 5 have an input pull-up
control register (PCR) for switching input pull-up transistors on and off.
Ports 1 to 6 and port 8 can drive one TTL load and a 90-pF capacitive load. Ports 9, A, and B can
drive one TTL load and a 30-pF capacitive load. Ports 1 to 6 and 8 to B can drive a darlington
pair. Ports 1, 2, and 5 can drive LEDs (with 10-mA current sink). Pins P82 to P80, PA7 to PA0
have Schmitt-trigger input circuits.
For block diagrams of the ports see appendix C, I/O Port Block Diagrams.
Rev. 3.00 Sep 14, 2005 page 263 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.1
Port Functions
Expanded Modes
Port
Description
Mode 1
P17 to P10/
A7 to A0
Address output pins (A7 to A0)
Address output (A7 to
A0) and generic input
DDR = 0:
generic input
DDR = 1:
address output
Generic input/output
P27 to P20/
A15 to A8
Address output pins (A15 to A8)
Address output (A15 to
A8) and generic input
DDR = 0:
generic input
DDR = 1:
address output
Generic input/output
Port 3 • 8-bit I/O port
P37 to P30/
D15 to D8
Data input/output (D15 to D8)
Generic input/output
Port 4 • 8-bit I/O port
P47 to P40/
D7 to D0
Data input/output (D7 to D0) and 8-bit generic input/output
8-bit bus mode: generic input/output
16-bit bus mode: data input/output
Generic input/output
P53 to P50/
A19 to A16
Address output (A19 to A16)
Generic input/output
Port 1 • 8-bit I/O port
• Can drive LEDs
Port 2 • 8-bit I/O port
• Built-in input pullup transistors
Mode 2
Mode 3
Single-Chip Modes
Pins
Mode 4 Mode 5
• Can drive LEDs
• Built-in input pullup transistors
Port 5 • 4-bit I/O port
• Built-in input pullup transistors
• Can drive LEDs
Port 6 • 8-bit I/O port
Port 7 • 8-bit I/O port
Address output (A19 to
A16) and 4-bit
generic input
DDR = 0: generic input
DDR = 1: address output
P67/φ
Clock output (φ) and generic input
P66/LWR
P65/HWR
P64/RD
P63/AS
Bus control signal output (LWR, HWR, RD, AS)
P62/BACK
P61/BREQ
P60/WAIT
Bus control signal input/output (BACK, BREQ, WAIT) and
3-bit generic input/output
P77/AN7/DA1
P76/AN6/DA0
Analog input (AN7, AN6) to A/D converter, analog output (DA1, DA0)
from D/A converter, and generic input
P75 to P70/
AN5 to AN0
Analog input (AN5 to AN0) to A/D converter, and generic input
Rev. 3.00 Sep 14, 2005 page 264 of 910
REJ09B0258-0300
Mode 6
Mode 7
Generic input/output
Section 8 I/O Ports
Expanded Modes
Port
Description
Port 8 • 5-bit I/O port
Pins
Mode 1
P84/CS0
DDR = 0: generic input
DDR = 1 (reset value): CS0 output
P83/IRQ3/
CS1/ADTRG
IRQ3 input, CS1 output, external trigger input (ADTRG) to A/D converter, and
• P82 to P80 have
Schmitt inputs
Port 9 • 6-bit I/O port
Port A • 8-bit I/O port
• Schmitt inputs
Port B • 8-bit I/O port
Mode 2
Mode 3
Mode 4
Single-Chip Modes
Mode 5
Mode 6
DDR = 0 (reset value):
generic input
DDR = 1: CS0 output
Generic input/output
generic input
DDR = 0 (after reset): generic input
DDR = 1: CS1 output
Mode 7
IRQ3 input, external
trigger input (ADTRG) to
A/D converter, and
generic input/output
P82/IRQ2/CS2 IRQ2 and IRQ1 input, CS2 and CS3 output, and generic input*
P81/IRQ1/CS3 DDR = 0 (reset value): generic input
DDR = 1: CS2 and CS3 output
IRQ2 and IRQ1 input and
P80/IRQ0
/RFSH
IRQ0 input, RFSH output, and generic input/output
IRQ0 input and generic
P95/IRQ5
/SCK1
P94/IRQ4
/SCK0
P93/RxD1
P92/RxD0
P91/TxD1
P90/TxD0
Input and output (SCK1, SCK0, RxD1, RxD0, TxD1, TxD0) for serial communication interfaces 1 and 0
(SCI1/0), IRQ5 and IRQ4 input, and 6-bit generic input/output
PA7/TP7/
Address output
Output (TP7) from programmable timing pattern (A20)
controller (TPC),
input or output (TIOCB2)
for 16-bit timer and
generic input/output
TIOCB2/A20
generic input/output
input/output
Address output (A20),
TPC output (TP7), input
or output (TIOCB2) for
16-bit timer, and generic
input/output
TPC output (TP7), 16-bit
timer input or output
(TIOCB2), and generic
input/output
PA6/TP6/
TIOCA2/A21
PA5/TP5/
TIOCB1/A22
PA4/TP4/
TIOCA1/A23
TPC output (TP6 to TP4), TPC output (TP6 to TP4),16-bit timer input and
16-bit timer input and
output (TIOCA2, TIOCB1, TIOCA1), address output
output (TIOCA2, TIOCB1, (A23 to A21), and generic input/output
TIOCA1) , and generic
input/output
PA3/TP3/
TIOCB0/
TCLKD
PA2/TP2/
TIOCA0/
TCLKC
PA1/TP1/
TCLKB
/TEND1
PA0/TP0/
TCLKA
/TEND0
TPC output (TP3 to TP0), 16-bit timer input and output (TIOCB0, TIOCA0, TCLKD, TCLKC, TCLKB,
TCLKA), 8-bit timer input (TCLKD, TCLKC, TCLKB, TCLKA), output (TEND1, TEND0) from DMA
controller (DMAC), and generic input/output
PB7/TP15/
RXD2
PB6/TP14/
TXD2
PB5/TP13/
SCK2/LCAS
PB4/TP12/
TPC output (TP15 to TP12), SCI2 input and output (SCK2 , RxD2, TxD2), DRAM TPC output (TP15 to
interface output (LCAS, UCAS), and generic input/output
TP12), SCI2 input and
output (SCK2, RxD2,
TxD2), and generic
input/output
PB3/TP11/
TMIO3/
DREQ1/CS4
PB2/TP10/
TMO2/CS5
PB1/TP9/
TMIO1/
DREQ0/CS6
PB0/TP8/
TMO0/CS7
TPC output (TP11 to TP8), 8-bit timer input and output (TMIO3, TMO2, TMIO1,
TMO0), DMAC input (DREQ1, DREQ0), CS7 to CS4 output, and generic
input/output
TPC output (TP6 to
TP4), 16-bit timer input
and output (TIOCA2,
TIOCB1, TIOCA1) and
generic input/output
UCAS
TPC output (TP11 to TP8),
8-bit timer input and
output (TMIO3, TMO2,
TMIO1, TMO0), DMAC
input (DREQ1, DREQ0),
and generic input/output
Note: * P81 can be used as an output port by making a setting in DRCRA.
Rev. 3.00 Sep 14, 2005 page 265 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.2
Port 1
8.2.1
Overview
Port 1 is an 8-bit input/output port also used for address output, with the pin configuration shown
in figure 8.1. The pin functions differ between the expanded modes with on-chip ROM disabled,
expanded modes with on-chip ROM enabled, and single-chip mode. In modes 1 to 4 (expanded
modes with on-chip ROM disabled), they are address bus output pins (A7 to A0).
In modes 5 (expanded modes with on-chip ROM enabled), settings in the port 1 data direction
register (P1DDR) can designate pins for address bus output (A7 to A0) or generic input. In mode 6
and 7 (single-chip mode), port 1 is a generic input/output port.
When DRAM is connected to area 2, 3, 4, 5, A7 to A0 output row and column addresses in read
and write cycles. For details see section 6.5, DRAM Interface.
Pins in port 1 can drive one TTL load and a 90-pF capacitive load. They can also drive an LED or
a darlington transistor pair.
Port 1 pins
Port 1
Modes 1 to 4
Modes 5
Mode 6 and 7
P17 /A 7
A 7 (output)
P17 (input)/A 7 (output)
P17 (input/output)
P16 /A 6
A 6 (output)
P16 (input)/A 6 (output)
P16 (input/output)
P15 /A 5
A 5 (output)
P15 (input)/A 5 (output)
P15 (input/output)
P14 /A 4
A 4 (output)
P14 (input)/A 4 (output)
P14 (input/output)
P13 /A 3
A 3 (output)
P13 (input)/A 3 (output)
P13 (input/output)
P12 /A 2
A 2 (output)
P12 (input)/A 2 (output)
P12 (input/output)
P11 /A 1
A 1 (output)
P11 (input)/A 1 (output)
P11 (input/output)
P10 /A 0
A 0 (output)
P10 (input)/A 0 (output)
P10 (input/output)
Figure 8.1 Port 1 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 266 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.2.2
Register Descriptions
Table 8.2 summarizes the registers of port 1.
Table 8.2
Port 1 Registers
Initial Value
Address*
Name
Abbreviation R/W
Modes 1 to 4
Modes 5 to 7
H'EE000
Port 1 data direction register P1DDR
W
H'FF
H'00
H'FFFD0
Port 1 data register
R/W
H'00
H'00
P1DR
Note: * Lower 20 bits of the address in advanced mode.
Port 1 Data Direction Register (P1DDR): P1DDR is an 8-bit write-only register that can select
input or output for each pin in port 1.
Bit
7
6
5
4
3
2
1
0
P1 7 DDR P1 6 DDR P1 5 DDR P1 4 DDR P1 3 DDR P1 2 DDR P1 1 DDR P1 0 DDR
Modes Initial value
1 to 4 Read/Write
Modes Initial value
5 to 7 Read/Write
1
1
1
1
1
1
1
1








0
0
0
0
0
0
0
0
W
W
W
W
W
W
W
W
Port 1 data direction 7 to 0
These bits select input or
output for port 1 pins
Modes 1 to 4 (Expanded Modes with On-Chip ROM Disabled): P1DDR values are fixed at 1.
Port 1 functions as an address bus.
Modes 5 (Expanded Modes with On-Chip ROM Enabled): After a reset, port 1 functions as
an input port.A pin in port 1 becomes an address output pin if the corresponding P1DDR bit is set
to 1, and a generic input pin if this bit is cleared to 0.
Mode 6 and 7 (Single-Chip Mode): Port 1 functions as an input/output port. A pin in port 1
becomes an output port if the corresponding P1DDR bit is set to 1, and an input port if this bit is
cleared to 0.
Rev. 3.00 Sep 14, 2005 page 267 of 910
REJ09B0258-0300
Section 8 I/O Ports
In modes 1 to 4, P1DDR bits are always read as 1, and cannot be modified.
In modes 5 to 7, P1DDR is a write-only register. Its value cannot be read. All bits return 1 when
read.
P1DDR is initialized to H'FF in modes 1 to 4, and to H'00 in modes 5 to 7, by a reset and in
hardware standby mode. In software standby mode it retains its previous setting. Therefore, if a
transition is made to software standby mode while port 1 is functioning as an input/output port
and a P1DDR bit is set to 1, the corresponding pin maintains its output state.
Port 1 Data Register (P1DR): P1DR is an 8-bit readable/writable register that stores port 1
output data. When port 1 functions as an output port, the value of this register is output. When
this register is read, the pin logic level is read for bits for which the P1DDR setting is 0, and the
P1DR value is read for bits for which the P1DDR setting is 1.
Bit
7
6
5
4
3
2
1
0
P1 7
P1 6
P1 5
P1 4
P1 3
P1 2
P1 1
P1 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 1 data 7 to 0
These bits store data for port 1 pins
P1DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 268 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.3
Port 2
8.3.1
Overview
Port 2 is an 8-bit input/output port with the pin configuration shown in figure 8.2. The pin
functions differ according to the operating mode.
In modes 1 to 4 (expanded modes with on-chip ROM disabled), port 2 consists of address bus
output pins (A15 to A8). In modes 5 (expanded modes with on-chip ROM enabled), settings in the
port 2 data direction register (P2DDR) can designate pins for address bus output (A15 to A8) or
generic input. In mode 6 and 7 (single-chip mode), port 2 is a generic input/output port.
When DRAM is connected to areas 2 to 5, A12 to A8 output row and column addresses in read and
write cycles. For details see section 6.5, DRAM Interface.
Port 2 has software-programmable built-in pull-up transistors.
Pins in port 2 can drive one TTL load and a 90-pF capacitive load. They can also drive an LED
or a darlington transistor pair.
Port 2
Port 2 pins
Modes 1 to 4
Modes 5
Mode 6 and 7
P27 /A 15
A15 (output)
P27 (input)/A15 (output)
P27 (input/output)
P26 /A 14
A14 (output)
P26 (input)/A14 (output)
P26 (input/output)
P25 /A 13
A13 (output)
P25 (input)/A13 (output)
P25 (input/output)
P24 /A 12
A12 (output)
P24 (input)/A12 (output)
P24 (input/output)
P23 /A 11
A11 (output)
P23 (input)/A11 (output)
P23 (input/output)
P22 /A 10
A10 (output)
P22 (input)/A10 (output)
P22 (input/output)
P21 /A 9
A9 (output)
P21 (input)/A9 (output)
P21 (input/output)
P20 /A 8
A8 (output)
P20 (input)/A8 (output)
P20 (input/output)
Figure 8.2 Port 2 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 269 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.3.2
Register Descriptions
Table 8.3 summarizes the registers of port 2.
Table 8.3
Port 2 Registers
Initial Value
Address*
Name
Abbreviation R/W Modes 1 to 4 Modes 5 to 7
H'EE001
Port 2 data direction register
P2DDR
W
H'FF
H'00
H'FFFD1
Port 2 data register
P2DR
R/W H'00
H'00
H'EE03C
Port 2 input pull-up MOS control
register
P2PCR
R/W H'00
H'00
Note: * Lower 20 bits of the address in advanced mode.
Port 2 Data Direction Register (P2DDR): P2DDR is an 8-bit write-only register that can select
input or output for each pin in port 2.
Bit
7
6
5
4
3
2
1
0
P2 7 DDR P2 6 DDR P2 5 DDR P2 4 DDR P2 3 DDR P2 2 DDR P2 1 DDR P2 0 DDR
Modes Initial value
1 to 4 Read/Write
Modes Initial value
5 to 7 Read/Write
1
1
1
1
1
1
1
1








0
0
0
0
0
0
0
0
W
W
W
W
W
W
W
W
Port 2 data direction 7 to 0
These bits select input or
output for port 2 pins
Modes 1 to 4 (Expanded Modes with On-Chip ROM Disabled): P2DDR values are fixed at 1.
Port 2 functions as an address bus.
Modes 5 (Expanded Modes with On-Chip ROM Enabled): Following a reset, port 2 is an
input port. A pin in port 2 becomes an address output pin if the corresponding P2DDR bit is set to
1, and a generic input port if this bit is cleared to 0.
Mode 6 and 7 (Single-Chip Mode): Port 2 functions as an input/output port. A pin in port 2
becomes an output port if the corresponding P2DDR bit is set to 1, and an input port if this bit is
cleared to 0.
Rev. 3.00 Sep 14, 2005 page 270 of 910
REJ09B0258-0300
Section 8 I/O Ports
In modes 1 to 4, P2DDR bits are always read as 1, and cannot be modified.
In modes 5 to 7, P2DDR is a write-only register. Its value cannot be read. All bits return 1 when
read.
P2DDR is initialized to H'FF in modes 1 to 4, and to H'00 in modes 5 to 7, by a reset and in
hardware standby mode. In software standby mode it retains its previous setting. Therefore, if a
transition is made to software standby mode while port 2 is functioning as an input/output port
and a P2DDR bit is set to 1, the corresponding pin maintains its output state.
Port 2 Data Register (P2DR): P2DR is an 8-bit readable/writable register that stores output data
for Port 2. When port 2 functions as an output port, the value of this register is output. When a bit
in P2DDR is set to 1, if port 2 is read the value of the corresponding P2DR bit is returned. When
a bit in P2DDR is cleared to 0, if port 2 is read the corresponding pin logic level is read.
Bit
7
6
5
4
3
2
1
0
P2 7
P2 6
P2 5
P2 4
P2 3
P2 2
P2 1
P2 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 2 data 7 to 0
These bits store data for port 2 pins
P2DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Port 2 Input Pull-Up MOS Control Register (P2PCR): P2PCR is an 8-bit readable/writable
register that controls the MOS input pull-up transistors in port 2.
Bit
7
6
5
4
3
2
1
0
P2 7 PCR P2 6 PCR P2 5 PCR P2 4 PCR P2 3 PCR P2 2 PCR P2 1 PCR P2 0 PCR
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 2 input pull-up MOS control 7 to 0
These bits control input pull-up
transistors built into port 2
In modes 5 to 7, when a P2DDR bit is cleared to 0 (selecting generic input), if the corresponding
bit in P2PCR is set to 1, the input pull-up transistor is turned on.
Rev. 3.00 Sep 14, 2005 page 271 of 910
REJ09B0258-0300
Section 8 I/O Ports
P2PCR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting.
Table 8.4
Input Pull-Up Transistor States (Port 2)
Mode
Reset
Hardware
Standby Mode
Software
Standby Mode
Other Modes
1
2
3
4
Off
Off
Off
Off
5
6
7
Off
Off
On/off
On/off
Legend
Off:
The input pull-up transistor is always off.
On/off: The input pull-up transistor is on if P2PCR = 1 and P2DDR = 0. Otherwise, it is off.
Rev. 3.00 Sep 14, 2005 page 272 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.4
Port 3
8.4.1
Overview
Port 3 is an 8-bit input/output port with the pin configuration shown in figure 8.3. Port 3 is a data
bus in modes 1 to 5 (expanded modes) and a generic input/output port in mode 6, 7 (single-chip
mode).
Pins in port 3 can drive one TTL load and a 90-pF capacitive load. They can also drive a
darlington transistor pair.
Port 3
Port 3 pins
Modes 1 to 5
Mode 6 and 7
P37 /D15
D15 (input/output)
P37 (input/output)
P36 /D14
D14 (input/output)
P36 (input/output)
P35 /D13
D13 (input/output)
P35 (input/output)
P34 /D12
D12 (input/output)
P34 (input/output)
P33 /D11
D11 (input/output)
P33 (input/output)
P32 /D10
D10 (input/output)
P32 (input/output)
P31 /D9
D9 (input/output)
P31 (input/output)
P30 /D8
D8 (input/output)
P30 (input/output)
Figure 8.3 Port 3 Pin Configuration
8.4.2
Register Descriptions
Table 8.5 summarizes the registers of port 3.
Table 8.5
Port 3 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'EE002
Port 3 data direction register
P3DDR
W
H'00
H'FFFD2
Port 3 data register
P3DR
R/W
H'00
Note: * Lower 20 bits of the address in advanced mode.
Rev. 3.00 Sep 14, 2005 page 273 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port 3 Data Direction Register (P3DDR): P3DDR is an 8-bit write-only register that can select
input or output for each pin in port 3.
Bit
7
6
5
4
3
2
1
0
P3 7 DDR P3 6 DDR P3 5 DDR P3 4 DDR P3 3 DDR P3 2 DDR P3 1 DDR P3 0 DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port 3 data direction 7 to 0
These bits select input or output for port 3 pins
Modes 1 to 5 (Expanded Modes): Port 3 functions as a data bus, regardless of the P3DDR
settings.
Mode 6 and 7 (Single-Chip Mode): Port 3 functions as an input/output port. A pin in port 3
becomes an output port if the corresponding P3DDR bit is set to 1, and an input port if this bit is
cleared to 0.
P3DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P3DDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting. Therefore, if a transition is made to software standby mode while
port 3 is functioning as an input/output port and a P3DDR bit is set to 1, the corresponding pin
maintains its output state.
Port 3 Data Register (P3DR): P3DR is an 8-bit readable/writable register that stores output data
for port 3. When port 3 functions as an output port, the value of this register is output. When a bit
in P3DDR is set to 1, if port 3 is read the value of the corresponding P3DR bit is returned. When
a bit in P3DDR is cleared to 0, if port 3 is read the corresponding pin logic level is read.
Bit
7
6
5
4
3
2
1
0
P3 7
P3 6
P3 5
P3 4
P3 3
P3 2
P3 1
P3 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 3 data 7 to 0
These bits store data for port 3 pins
P3DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 274 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.5
Port 4
8.5.1
Overview
Port 4 is an 8-bit input/output port with the pin configuration shown in figure 8.4. The pin
functions differ depending on the operating mode.
In modes 1 to 5 (expanded modes), when the bus width control register (ABWCR) designates
areas 0 to 7 all as 8-bit-access areas, the chip operates in 8-bit bus mode and port 4 is a generic
input/output port. When at least one of areas 0 to 7 is designated as a 16-bit-access area, the chip
operates in 16-bit bus mode and port 4 becomes part of the data bus. In mode 6, 7 (single-chip
mode), port 4 is a generic input/output port.
Port 4 has software-programmable built-in pull-up transistors.
Pins in port 4 can drive one TTL load and a 90-pF capacitive load. They can also drive a
darlington transistor pair.
Port 4
Port 4 pins
Modes 1 to 5
Mode 6 and 7
P47 /D7
P47 (input/output)/D7 (input/output)
P47 (input/output)
P46 /D6
P46 (input/output)/D6 (input/output)
P46 (input/output)
P45 /D5
P45 (input/output)/D5 (input/output)
P45 (input/output)
P44 /D4
P44 (input/output)/D4 (input/output)
P44 (input/output)
P43 /D3
P43 (input/output)/D3 (input/output)
P43 (input/output)
P42 /D2
P42 (input/output)/D2 (input/output)
P42 (input/output)
P41 /D1
P41 (input/output)/D1 (input/output)
P41 (input/output)
P40 /D0
P40 (input/output)/D0 (input/output)
P40 (input/output)
Figure 8.4 Port 4 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 275 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.5.2
Register Descriptions
Table 8.6 summarizes the registers of port 4.
Table 8.6
Port 4 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'EE003
Port 4 data direction register
P4DDR
W
H'00
H'FFFD3
Port 4 data register
P4DR
R/W
H'00
H'EE03E
Port 4 input pull-up control register
P4PCR
R/W
H'00
Note: * Lower 20 bits of the address in advanced mode.
Port 4 Data Direction Register (P4DDR): P4DDR is an 8-bit write-only register that can select
input or output for each pin in port 4.
Bit
7
6
5
4
3
2
1
0
P4 7 DDR P4 6 DDR P4 5 DDR P4 4 DDR P4 3 DDR P4 2 DDR P4 1 DDR P4 0 DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port 4 data direction 7 to 0
These bits select input or output for port 4 pins
Modes 1 to 5 (Expanded Modes): When all areas are designated as 8-bit-access areas by the bus
controller’s bus width control register (ABWCR), selecting 8-bit bus mode, port 4 functions as an
input/output port. In this case, a pin in port 4 becomes an output port if the corresponding P4DDR
bit is set to 1, and an input port if this bit is cleared to 0.
When at least one area is designated as a 16-bit-access area, selecting 16-bit bus mode, port 4
functions as part of the data bus, regardless of the P4DDR settings.
Mode 6 and 7 (Single-Chip Mode): Port 4 functions as an input/output port. A pin in port 4
becomes an output port if the corresponding P4DDR bit is set to 1, and an input port if this bit is
cleared to 0.
P4DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P4DDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 276 of 910
REJ09B0258-0300
Section 8 I/O Ports
ABWCR and P4DDR are not initialized in software standby mode. Therefore, if a transition is
made to software standby mode while port 4 is functioning as an input/output port and a P4DDR
bit is set to 1, the corresponding pin maintains its output state.
Port 4 Data Register (P4DR): P4DR is an 8-bit readable/writable register that stores output data
for port 4. When port 4 functions as an output port, the value of this register is output. When a bit
in P4DDR is set to 1, if port 4 is read the value of the corresponding P4DR bit is returned. When
a bit in P4DDR is cleared to 0, if port 4 is read the corresponding pin logic level is read.
Bit
7
6
5
4
3
2
1
0
P47
P46
P45
P44
P43
P42
P41
P40
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 4 data 7 to 0
These bits store data for port 4 pins
P4DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Port 4 Input Pull-Up MOS Control Register (P4PCR): P4PCR is an 8-bit readable/writable
register that controls the MOS input pull-up transistors in port 4.
Bit
7
6
5
4
3
2
1
0
P4 7 PCR P4 6 PCR P4 5 PCR P4 4 PCR P4 3 PCR P4 2 PCR P4 1 PCR P4 0 PCR
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 4 input pull-up control 7 to 0
These bits control input pull-up transistors built into port 4
In mode 6 and 7 (single-chip mode), and in 8-bit bus mode in modes 1 to 5 (expanded modes),
when a P4DDR bit is cleared to 0 (selecting generic input), if the corresponding P4PCR bit is set
to 1, the input pull-up transistor is turned on.
P4PCR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 277 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.7 summarizes the states of the input pull-ups in each operating mode.
Table 8.7
Input Pull-Up Transistor States (Port 4)
Mode
1 to 5
8-bit bus mode
Reset
Hardware
Standby Mode
Software
Standby Mode
Other Modes
Off
Off
On/off
On/off
Off
Off
On/off
On/off
16-bit bus mode
6 and 7
Legend
Off:
The input pull-up transistor is always off.
On/off: The input pull-up transistor is on if P4PCR = 1 and P4DDR = 0. Otherwise, it is off.
Rev. 3.00 Sep 14, 2005 page 278 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.6
Port 5
8.6.1
Overview
Port 5 is a 4-bit input/output port with the pin configuration shown in figure 8.5. The pin
functions differ depending on the operating mode.
In modes 1 to 4 (expanded modes with on-chip ROM disabled), port 5 consists of address output
pins (A19 to A16). In modes 5 (expanded modes with on-chip ROM enabled), settings in the port 5
data direction register (P5DDR) designate pins for address bus output (A19 to A16) or generic
input. In mode 6, 7 (single-chip mode), port 5 is a generic input/output port.
Port 5 has software-programmable built-in pull-up transistors.
Pins in port 5 can drive one TTL load and a 90-pF capacitive load. They can also drive an LED or
a darlington transistor pair.
Port 5
Port 5
pins
Modes 1 to 4
Mode 5
Mode 6 and 7
P53 /A 19
A19 (output)
P5 3 (input)/A19 (output)
P5 3 (input/output)
P52 /A 18
A18 (output)
P5 2 (input)/A18 (output)
P5 2 (input/output)
P51 /A 17
A17 (output)
P5 1 (input)/A17 (output)
P5 1 (input/output)
P50 /A 16
A16 (output)
P5 0 (input)/A16 (output)
P5 0 (input/output)
Figure 8.5 Port 5 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 279 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.6.2
Register Descriptions
Table 8.8 summarizes the registers of port 5.
Table 8.8
Port 5 Registers
Initial Value
Address* Name
Abbreviation
R/W Modes 1 to 4 Modes 5 to 7
H'EE004
P5DDR
W
H'FF
H'F0
P5DR
R/W H'F0
H'F0
R/W H'F0
H'F0
Port 5 data direction register
H'FFFD4 Port 5 data register
H'EE03F Port 5 input pull-up control register P5PCR
Note: * Lower 20 bits of the address in advanced mode.
Port 5 Data Direction Register (P5DDR): P5DDR is an 8-bit write-only register that can select
input or output for each pin in port 5.
Bits 7 to 4 are reserved. They are fixed at 1, and cannot be modified.
Bit
Modes Initial value
1 to 4 Read/Write
Modes Initial value
5 to 7 Read/Write
7
6
5
4
—
—
—
—
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
1
1
1
1
0
0
0
0
—
—
—
—
W
W
W
W
Reserved bits
3
2
1
0
P5 3 DDR P5 2 DDR P5 1 DDR P5 0 DDR
Port 5 data direction 3 to 0
These bits select input or
output for port 5 pins
Modes 1 to 4 (Expanded Modes with On-Chip ROM Disabled): P5DDR values are fixed at 1.
Port 5 functions as an address bus.
Modes 5 (Expanded Modes with On-Chip ROM Enabled): Following a reset, port 5 is an
input port. A pin in port 5 becomes an address output pin if the corresponding P5DDR bit is set to
1, and an input port if this bit is cleared to 0.
Mode 6 and 7 (Single-Chip Mode): Port 5 functions as an input/output port. A pin in port 5
becomes an output port if the corresponding P5DDR bit is set to 1, and an input port if this bit is
cleared to 0.
Rev. 3.00 Sep 14, 2005 page 280 of 910
REJ09B0258-0300
Section 8 I/O Ports
In modes 1 to 4, P5DDR bits are always read as 1, and cannot be modified.
In modes 5 to 7, P5DDR is a write-only register. Its value cannot be read. All bits return 1 when
read.
P5DDR is initialized to H'FF in modes 1 to 4, and to H'F0 in modes 5 to 7, by a reset and in
hardware standby mode. In software standby mode it retains its previous setting. Therefore, if a
transition is made to software standby mode while port 5 is functioning as an input/output port
and a P5DDR bit is set to 1, the corresponding pin maintains its output state.
Port 5 Data Register (P5DR): P5DR is an 8-bit readable/writable register that stores output data
for port 5. When port 5 functions as an output port, the value of this register is output. When a bit
in P5DDR is set to 1, if port 5 is read the value of the corresponding P5DR bit is returned. When
a bit in P5DDR is cleared to 0, if port 5 is read the corresponding pin logic level is read.
Bits 7 to 4 are reserved. They are fixed at 1, and cannot be modified.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
P5 3
P5 2
P5 1
P5 0
Initial value
1
1
1
1
0
0
0
0
Read/Write
—
—
—
—
R/W
R/W
R/W
R/W
Reserved bits
Port 5 data 3 to 0
These bits store data
for port 5 pins
P5DR is initialized to H'F0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 281 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port 5 Input Pull-Up MOS Control Register (P5PCR): P5PCR is an 8-bit readable/writable
register that controls the MOS input pull-up transistors in port 5.
Bits 7 to 4 are reserved. They are fixed at 1, and cannot be modified.
Bit
7
6
5
4




2
Initial value
1
1
1
1
0
0
0
0
Read/Write




R/W
R/W
R/W
R/W
3
1
0
P5 3 PCR P5 2 PCR P5 1 PCR P5 0 PCR
Reserved bits
Port 5 input pull-up control 3 to 0
These bits control input pull-up
transistors built into port 5
In modes 5 to 7, when a P5DDR bit is cleared to 0 (selecting generic input), if the corresponding
bit in P5PCR is set to 1, the input pull-up transistor is turned on.
P5PCR is initialized to H'F0 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting.
Table 8.9 summarizes the states of the input pull-ups in each mode.
Table 8.9
Input Pull-Up Transistor States (Port 5)
Mode
Reset
Hardware Standby Mode
Software Standby Mode
Other Modes
1
2
3
4
Off
Off
Off
Off
5
6
7
Off
Off
On/off
On/off
Legend
Off:
The input pull-up transistor is always off.
On/off: The input pull-up transistor is on if P5PCR = 1 and P5DDR = 0. Otherwise, it is off.
Rev. 3.00 Sep 14, 2005 page 282 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.7
Port 6
8.7.1
Overview
Port 6 is an 8-bit input/output port that is also used for input and output of bus control signals
(LWR, HWR, RD, AS, BACK, BREQ, WAIT) and for clock (φ) output.
In modes 1 to 5 (expanded modes), the pin functions are P67 (generic input)/φ, LWR, HWR, RD,
AS, P62/BACK, P61/BREQ, and P60/WAIT). See table 8.11 for the selection of the pin functions.
In modes 6 and 7 (single-chip modes), P67 functions as a generic input port or ø output, and P66
to P60 function as generic input/output ports.
When DRAM is connected to areas 2 to 5, LWR, HWR, and RD also function as LCAS, UCAS,
and WE, respectively. For details see section 6.5, DRAM Interface.
Pins in port 6 can drive one TTL load and a 90-pF capacitive load. They can also drive a
darlington transistor pair.
Port 6 pins
P6 7 / φ
Port 6
Mode 6 and 7
(single-chip mode)
Modes 1 to 5
(expanded modes)
P67 (input)/ φ
(output)
P6 7 (input) / φ(output)
P6 6 / LWR
LWR (output)
P6 6 (input/output)
P6 5 / HWR
HWR (output)
P6 5 (input/output)
P6 4 / RD
RD
(output)
P6 4 (input/output)
P6 3 / AS
AS
(output)
P6 3 (input/output)
P6 2 / BACK
P62 (input/output)/ BACK (output)
P6 2 (input/output)
P6 1 / BREQ
P61 (input/output)/ BREQ (input)
P6 1 (input/output)
P6 0 / WAIT
P60 (input/output)/ WAIT (input)
P6 0 (input/output)
Figure 8.6 Port 6 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 283 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.7.2
Register Descriptions
Table 8.10 summarizes the registers of port 6.
Table 8.10 Port 6 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'EE005
Port 6 data direction register
P6DDR
W
H'80
H'FFFD5
Port 6 data register
P6DR
R/W
H'80
Note: * Lower 20 bits of the address in advanced mode.
Port 6 Data Direction Register (P6DDR): P6DDR is an 8-bit write-only register that can select
input or output for each pin in port 6.
Bit 7 is reserved. It is fixed at 1, and cannot be modified.
Bit
7
—
6
5
4
3
2
1
0
P6 6 DDR P6 5 DDR P6 4 DDR P6 3 DDR P6 2 DDR P6 1 DDR P6 0 DDR
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
W
W
W
W
W
W
W
Reserved bit
Port 6 data direction 6 to 0
These bits select input or output for port 6 pins
Modes 1 to 5 (Expanded Modes): P67 functions as the clock output pin (φ) or an input port. P67
is the clock output pin (ø) if the PSTOP bit in MSTRCH is cleared to 0 (initial value), and an
input port if this bit is set to 1.
P66 to P63 function as bus control output pins (LWR, HWR, RD, and AS), regardless of the
settings of bits P66DDR to P63DDR.
P62 to P60 function as bus control input/output pins (BACK, BREQ, and WAIT) or input/output
ports. For the method of selecting the pin functions, see table 8.11.
When P62 to P60 function as input/output ports, the pin becomes an output port if the
corresponding P6DDR bit is set to 1, and an input port if this bit is cleared to 0.
Mode 6 and 7 (Single-Chip Mode): P67 functions as the clock output pin (φ) or an input port.
P66 to P60 function as generic input/output ports. P67 is the clock output pin (φ) if the PSTOP bit
in MSTCRH is cleared to 0 (initial value), and an input port if this bit is set to 1. A pin in port 6
Rev. 3.00 Sep 14, 2005 page 284 of 910
REJ09B0258-0300
Section 8 I/O Ports
becomes an output port if the corresponding bit of P66DDR to P60DDR is set to 1, and an input
port if this pin is cleared to 0.
P6DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P6DDR is initialized to H'80 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting. Therefore, if a transition is made to software standby mode while
port 6 is functioning as an input/output port and a P6DDR bit is set to 1, the corresponding pin
maintains its output state.
Port 6 Data Register (P6DR): P6DR is an 8-bit readable/writable register that stores output data
for port 6. When port 6 functions as an output port, the value of this register is output. For bit 7, a
value of 1 is returned if the bit is read while the PSTOP bit in MSTCRH is cleared to 0, and the
P67 pin logic level is returned if the bit is read while the PSTOP bit is set to 1. Bit 7 cannot be
modified. For bits 6 to 0, the pin logic level is returned if the bit is read while the corresponding
bit in P6DDR is cleared to 0, and the P6DR value is returned if the bit is read while the
corresponding bit in P6DDR is set to 1.
Bit
7
6
5
4
3
2
1
0
P67
P6 6
P6 5
P6 4
P6 3
P6 2
P6 1
P6 0
Initial value
1
0
0
0
0
0
0
0
Read/Write
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port 6 data 7 to 0
These bits store data for port 6 pins
P6DR is initialized to H'80 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 285 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.11 Port 6 Pin Functions in Modes 1 to 5
Pin
Pin Functions and Selection Method
P67/φ
Bit PSTOP in MSTCRH selects the pin function.
PSTOP
Pin function
LWR
0
1
φ output
P67 input
Functions as LWR regardless of the setting of bit P66DDR
P66DDR
0
1
LWR output*
Pin function
Note: * If any of bits DRAS2 to DRAS0 in DRCRA is 1 and bit CSEL in DRCRB is 1, LWR
output functions as LCAS.
HWR
Functions as HWR regardless of the setting of bit P65DDR
P65DDR
0
1
HWR output*
Pin function
Note: * If any of bits DRAS2 to DRAS0 in DRCRA is 1 and bit CSEL in DRCRB is 1, HWR
output functions as UCAS.
RD
Functions as RD regardless of the setting of bit P64DDR
P64DDR
0
1
RD output*
Pin function
Note: * If any of bits DRAS2 to DRAS0 in DRCRA is 1, RD output functions as WE.
AS
Functions as AS regardless of the setting of bit P63DDR
P63DDR
0
1
AS output
Pin function
P62/BACK
Bit BRLE in BRCR and bit P62DDR select the pin function as follows
BRLE
P62DDR
Pin function
P61/BREQ
0
1
—
P62 input
P62 output
BACK output
Bit BRLE in BRCR and bit P61DDR select the pin function as follows
BRLE
P61DDR
Pin function
P60/WAIT
1
0
0
1
0
1
—
P61 input
P61 output
BREQ input
Bit WAITE in BCR and bit P60DDR select the pin function as follows.
WAITE
P60DDR
Pin function
0
1
0*
P60 input
P60 output
WAIT input
Note: * Do not set bit P60DDR to 1.
Rev. 3.00 Sep 14, 2005 page 286 of 910
REJ09B0258-0300
1
0
Section 8 I/O Ports
8.8
Port 7
8.8.1
Overview
Port 7 is an 8-bit input port that is also used for analog input to the A/D converter and analog
output from the D/A converter. The pin functions are the same in all operating modes. Figure 8.7
shows the pin configuration of port 7.
See section 15, A/D Converter, for details of the A/D converter analog input pins, and section 16,
D/A Converter, for details of the D/A converter analog output pins.
Port 7 pins
P77 (input)/AN 7 (input)/DA 1 (output)
P76 (input)/AN 6 (input)/DA 0 (output)
P75 (input)/AN 5 (input)
Port 7
P74 (input)/AN 4 (input)
P73 (input)/AN 3 (input)
P72 (input)/AN 2 (input)
P71 (input)/AN 1 (input)
P70 (input)/AN 0 (input)
Figure 8.7 Port 7 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 287 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.8.2
Register Description
Table 8.12 summarizes the port 7 register. Port 7 is an input port, and port 7 has no data direction
register.
Table 8.12 Port 7 Data Register
Address*
Name
Abbreviation
R/W
Initial Value
H'FFFD6
Port 7 data register
P7DR
R
Undetermined
Note: * Lower 20 bits of the address in advanced mode.
Port 7 Data Register (P7DR)
Bit
7
6
5
4
3
2
1
0
P77
P76
P75
P74
P73
P72
P71
P70
Initial value
—*
—*
—*
—*
—*
—*
—*
—*
Read/Write
R
R
R
R
R
R
R
R
Note: * Determined by pins P77 to P70.
When port 7 is read, the pin logic levels are always read. P7DR cannot be modified.
Rev. 3.00 Sep 14, 2005 page 288 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.9
Port 8
8.9.1
Overview
Port 8 is a 5-bit input/output port that is also used for CS3 to CS0 output, RFSH output, IRQ3 to
IRQ0 input, and A/D converter ADTRG input. Figure 8.8 shows the pin configuration of port 8.
In modes 1 to 5 (expanded modes), port 8 can provide CS3 to CS0 output, RFSH output, IRQ3 to
IRQ0 input, and ADTRG input. See table 8.14 for the selection of pin functions in expanded
modes.
In modes 6 and 7 (single-chip modes), port 8 can provide IRQ3 to IRQ0 input and ADTRG input.
See table 8.15 for the selection of pin functions in single-chip mode.
See section 15, A/D Converter, for a description of the A/D converter's ADTRG input pin.
The IRQ3 to IRQ0 functions are selected by IER settings, regardless of whether the pin is used for
input or output. Caution is therefore required. For details see section 5.3.1, External Interrupts.
When DRAM is connected to areas 2 to 5, the CS3 and CS2 output pins function as RAS output
pins for each area. For details see section 6.5, DRAM Interface.
Pins in port 8 can drive one TTL load and a 90-pF capacitive load. They can also drive a
darlington transistor pair.
Pins P82 to P80 have Schmitt-trigger inputs.
Rev. 3.00 Sep 14, 2005 page 289 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port 8
Port 8 pins
Pin functions in modes 1 to 5
(expanded modes)
P84 / CS 0
P84 (input)/ CS 0 (output)
P83 / CS 1 / IRQ 3 / ADTRG
P83 (input)/ CS 1 (output)/ IRQ 3 (input) / ADTRG (input)
P82 / CS 2 / IRQ 2
P82 (input)/ CS 2 (output)/ IRQ 2 (input)
P81 / CS 3 / IRQ 1
P81 (input/output)/ CS3 (output)/IRQ1(input)
P80 / RFSH /IRQ 0
P80 (input/output)/ RFSH (output)/ IRQ 0 (input)
Pin functions in mode 6 and 7
(single-chip mode)
P84 /(input/output)
P83 /(input/output)/ IRQ 3 (input) / ADTRG (input)
P82 /(input/output)/ IRQ 2 (input)
P81 /(input/output)/ IRQ 1 (input)
P80 /(input/output)/ IRQ 0 (input)
Figure 8.8 Port 8 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 290 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.9.2
Register Descriptions
Table 8.13 summarizes the registers of port 8.
Table 8.13 Port 8 Registers
Initial Value
Address*
Name
Abbreviation
R/W
Mode 1 to 4
Mode 5 to 7
H'EE007
Port 8 data direction
register
P8DDR
W
H'F0
H'E0
H'FFFD7
Port 8 data register
P8DR
R/W
H'E0
H'E0
Note: * Lower 20 bits of the address in advanced mode.
Port 8 Data Direction Register (P8DDR): P8DDR is an 8-bit write-only register that can select
input or output for each pin in port 8.
Bits 7 to 5 are reserved. They are fixed at 1, and cannot be modified.
Bit
7
6
5

4
3
2
1
0


Modes Initial value
1 to 4 Read/Write
1
1
1
1
0
0
0
0



W
W
W
W
W
Modes Initial value
5 to 7 Read/Write
1
1
1
0
0
0
0
0



W
W
W
W
W
Reserved bits
P8 4 DDR P8 3 DDR P8 2 DDR P8 1 DDR P8 0 DDR
Port 8 data direction 4 to 0
These bits select input or
output for port 8 pins
Modes 1 to 5 (Expanded Modes): When bits in P8DDR bit are set to 1, P84 to P81 become CS0
to CS3 output pins. When bits in P8DDR are cleared to 0, the corresponding pins become input
ports. However, P81 can also be used as an output port, depending on the setting of bits DRAS2 to
DRAS0 in DRAM control register A (DRCRA). For details see section 6.5.2, DRAM Space and
RAS Output Pin Settings.
In modes 1 to 4 (expanded modes with on-chip ROM disabled), following a reset P84 functions as
the CS0 output, while CS1 to CS3 are input ports. In mode 5 (expanded mode with on-chip ROM
enabled), following a reset CS0 to CS3 are all input ports.
Rev. 3.00 Sep 14, 2005 page 291 of 910
REJ09B0258-0300
Section 8 I/O Ports
When the refresh enable bit (RFSHE) in DRCRA is set to 1, P80 is used for RFSH output. When
RFSHE is cleared to 0, P80 becomes an input/output port according to the P8DDR setting. For
details see table 8.14.
Mode 6 and 7 (Single-Chip Mode): Port 8 is a generic input/output port. A pin in port 8
becomes an output port if the corresponding P8DDR bit is set to 1, and an input port if this bit is
cleared to 0.
P8DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P8DDR is initialized to H'F0 in modes 1 to 4, and to H'E0 in modes 5 to 7, by a reset and in
hardware standby mode. In software standby mode P8DDR retains its previous setting.
Therefore, if a transition is made to software standby mode while port 8 is functioning as an
input/output port and a P8DDR bit is set to 1, the corresponding pin maintains its output state.
Port 8 Data Register (P8DR): P8DR is an 8-bit readable/writable register that stores output data
for port 8. When port 8 functions as an output port, the value of this register is output. When a bit
in P8DDR is set to 1, if port 8 is read the value of the corresponding P8DR bit is returned. When
a bit in P8DDR is cleared to 0, if port 8 is read the corresponding pin logic level is read.
Bits 7 to 5 are reserved. They are fixed at 1, and cannot be modified.
Bit
7
6
5
4
3
2
1
0



P8 4
P8 3
P8 2
P8 1
P8 0
Initial value
1
1
1
0
0
0
0
0
Read/Write



R/W
R/W
R/W
R/W
R/W
Reserved bits
Port 8 data 4 to 0
These bits store data
for port 8 pins
P8DR is initialized to H'E0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 292 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.14 Port 8 Pin Functions in Modes 1 to 5
Pin
Pin Functions and Selection Method
P84/CS0
Bit P84DDR selects the pin function as follows
P84DDR
Pin function
P83/CS1/IRQ3/ADTRG
0
1
P84 input
CS0 output
Bit P83DDR selects the pin function as follows
P83DDR
Pin function
0
1
P83 input
CS1 output
IRQ3 input
ADTRG input
P82/CS2/IRQ2
The DRAM interface settings by bits DRAS2 to DRAS0 in DRCRA, and bit P82DDR, select
the pin function as follows.
DRAM interface
settings
(1) in table below
P82DDR
Pin function
0
|(2) in table below
1
—
CS2 output
IRQ3 input
P82 input
CS2 output*
Note: * CS2 is output as RAS2.
DRAM interface
setting
(1)
(2)
DRAS2
0
DRAS1
DRAS0
P81/CS3/IRQ1
1
0
0
1
1
0
0
1
0
1
1
0
1
The DRAM interface settings by bits DRAS2 to DRAS0 in DRCRA, and bit P81DDR, select
the pin function as follows.
DRAM interface
settings
(1) in table below
P81DDR
Pin function
0
1
P81 input
pin
CS3
(2) in table below
0
output pin
(3) in table below
1
—
CS3 output pin*
P81 input P81 output
pin
pin
IRQ1 input pin
Note: * CS3 is output as RAS3.
DRAM interface
setting
(1)
(3)
DRAS2
DRAS1
DRAS0
P80/RFSH/IRQ0
(2)
(3)
(2)
0
1
0
0
1
1
0
0
1
0
1
1
0
1
Bit RFSHE in DRCRA and bit P80DDR select the pin function as follows.
RFSHE
P80DDR
Pin function
0
1*
0
1
—
P80 input
P80 output
RFSH output
IRQ0 input
Note: * If areas 2 to 5 are not designated as DRAM space, this bit should not be set to 1.
Rev. 3.00 Sep 14, 2005 page 293 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.15 Port 8 Pin Functions in Mode 6 and 7
Pin
Pin Functions and Selection Method
P84
Bit P84DDR selects the pin function as follows
P84DDR
Pin function
P83/IRQ3/ADTRG
0
1
P84 input
P84 output
Bit P83DDR selects the pin function as follows
P83DDR
Pin function
0
1
P83 input
P83 output
IRQ3 input
ADTRG input
P82/IRQ2
Bit P82DDR selects the pin function as follows
P82DDR
Pin function
0
1
P82 input
P82 output
IRQ2 input
P81/IRQ1
Bit P81DDR selects the pin function as follows
P81DDR
Pin function
0
1
P81 input
P81 output
IRQ1 input
P80/IRQ0
Bit P80DDR select the pin function as follows
P80DDR
Pin function
0
1
P80 input
P80 output
IRQ0 input
Rev. 3.00 Sep 14, 2005 page 294 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.10
Port 9
8.10.1
Overview
Port 9 is a 6-bit input/output port that is also used for input and output (TxD0, TxD1, RxD0, RxD1,
SCK0, SCK1) by serial communication interface channels 0 and 1 (SCI0 and SCI1), and for IRQ5
and IRQ4 input. See table 8.17 for the selection of pin functions.
The IRQ5 and IRQ4 functions are selected by IER settings, regardless of whether the pin is used
for input or output. Caution is therefore required. For details see section 5.3.1, External
Interrupts.
Port 9 has the same set of pin functions in all operating modes. Figure 8.9 shows the pin
configuration of port 9.
Pins in port 9 can drive one TTL load and a 30-pF capacitive load. They can also drive a
darlington transistor pair.
Port 9 pins
P95 (input/output)/SCK 1 (input/output)/IRQ 5 (input)
P94 (input/output)/SCK 0 (input/output)/IRQ 4 (input)
Port 9
P93 (input/output)/RxD1 (input)
P92 (input/output)/RxD0 (input)
P91 (input/output)/TxD1 (output)
P90 (input/output)/TxD0 (output)
Figure 8.9 Port 9 Pin Configuration
Rev. 3.00 Sep 14, 2005 page 295 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.10.2
Register Descriptions
Table 8.16 summarizes the registers of port 9.
Table 8.16 Port 9 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'EE008
Port 9 data direction register
P9DDR
W
H'C0
H'FFFD8
Port 9 data register
P9DR
R/W
H'C0
Note: * Lower 20 bits of the address in advanced mode.
Port 9 Data Direction Register (P9DDR): P9DDR is an 8-bit write-only register that can select
input or output for each pin in port 9.
Bits 7 and 6 are reserved. They are fixed at 1, and cannot be modified.
Bit
7
6


5
4
3
2
1
0
P9 5 DDR P9 4 DDR P9 3 DDR P9 2 DDR P9 1 DDR P9 0 DDR
Initial value
1
1
0
0
0
0
0
0
Read/Write


W
W
W
W
W
W
Reserved bits
Port 9 data direction 5 to 0
These bits select input or
output for port 9 pins
When port 9 functions as an input/output port, a pin in port 9 becomes an output port if the
corresponding P9DDR bit is set to 1, and an input port if this bit is cleared to 0. For the method of
selecting the pin functions, see table 8.17.
P9DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P9DDR is initialized to H'C0 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting. Therefore, if a transition is made to software standby mode while
port 9 is functioning as an input/output port and a P9DDR bit is set to 1, the corresponding pin
maintains its output state.
Rev. 3.00 Sep 14, 2005 page 296 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port 9 Data Register (P9DR): P9DR is an 8-bit readable/writable register that stores output data
for port 9. When port 9 functions as an output port, the value of this register is output. When a bit
in P9DDR is set to 1, if port 9 is read the value of the corresponding P9DR bit is returned. When
a bit in P9DDR is cleared to 0, if port 9 is read the corresponding pin logic level is read.
Bits 7 and 6 are reserved. They are fixed at 1, and cannot be modified.
Bit
7
6
5
4
3
2
1
0


P95
P94
P9 3
P9 2
P9 1
P9 0
Initial value
1
1
0
0
0
0
0
0
Read/Write


R/W
R/W
R/W
R/W
R/W
R/W
Reserved bits
Port 9 data 5 to 0
These bits store data
for port 9 pins
P9DR is initialized to H'C0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 297 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.17 Port 9 Pin Functions
Pin
Pin Functions and Selection Method
P95/SCK1/IRQ5
Bit C/A in SMR of SCI1, bits CKE0 and CKE1 in SCR, and bit P95DDR select the pin function
as follows
CKE1
0
C/A
0
CKE0
P95DDR
Pin function
1
0
1
—
1
—
—
0
1
—
—
—
P95
input
P95
output
SCK1 output
SCK1 output
SCK1 input
IRQ5 input
P94/SCK0/IRQ4
Bit C/A in SMR of SCI0, bits CKE0 and CKE1 in SCR, and bit P94DDR select the pin function
as follows
CKE1
0
C/A
CKE0
P94DDR
Pin function
1
0
0
1
1
—
—
—
0
1
—
—
—
P94
input
P94
output
SCK0 output
SCK0 output
SCK0 input
IRQ4 input
P93/RxD1
Bit RE in SCR of SCI1, bit SMIF in SCMR, and bit P93DDR select the pin function as follows.
SMIF
0
RE
P93DDR
Pin function
P92/RxD0
0
0
P93 input
1
1
P93 output
—
—
—
RxD1 input
RxD1 input
Bit RE in SCR of SCI0, bit SMIF in SCMR, and bit P92DDR select the pin function as follows
SMIF
0
RE
P92DDR
Pin function
Rev. 3.00 Sep 14, 2005 page 298 of 910
REJ09B0258-0300
0
1
1
—
0
1
—
—
P92 input
P92 output
RxD0 input
RxD0 input
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
P91/TxD1
Bit TE in SCR of SCI1, bit SMIF in SCMR, and bit P91DDR select the pin function as follows.
SMIF
0
TE
P91 DDR
Pin function
0
1
1
—
0
1
—
—
P91 input
P91 output
TxD1 output
TxD1 output*
Note: * Functions as the TxD1 output pin, but there are two states: one in which the pin is
driven, and another in which the pin is at high-impedance.
P90/TxD0
Bit TE in SCR of SCI0, bit SMIF in SCMR, and bit P90DDR select the pin function as follows.
SMIF
0
TE
P90DDR
Pin function
0
1
1
—
0
1
—
—
P90 input
P90 output
TxD0 output
TxD0 output*
Note: * Functions as the TxD0 output pin, but there are two states: one in which the pin is
driven, and another in which the pin is at highimpedance.
Rev. 3.00 Sep 14, 2005 page 299 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.11
Port A
8.11.1
Overview
Port A is an 8-bit input/output port that is also used for output (TP7 to TP0) from the
programmable timing pattern controller (TPC), input and output, (TIOCB2, TIOCA2, TIOCB1,
TIOCA1, TIOCB0, TIOCA0, TCLKD, TCLKC, TCLKB, TCLKA) by the 16-bit timer, input
(TCLKD, TCLKC, TCLKB, TCLKA) to the 8-bit timer, output (TEND1, TEND0) from the DMA
controller (DMAC), and address output (A23 to A20). A reset or hardware standby transition
leaves port A as an input port, except that in modes 3 and 4, one pin is always used for A20 output.
See table 8.19 to 8.21 for the selection of pin functions.
Usage of pins for TPC, 16-bit timer, 8-bit timer, and DMAC input and output is described in the
sections on those modules. For output of address bits A23 to A20 in modes 3, 4, and 5, see section
6.2.4, Bus Release Control Register (BRCR). Pins not assigned to any of these functions are
available for generic input/output. Figure 8.10 shows the pin configuration of port A.
Pins in port A can drive one TTL load and a 30-pF capacitive load. They can also drive a
darlington transistor pair. Port A has Schmitt-trigger inputs.
Rev. 3.00 Sep 14, 2005 page 300 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port A pins
PA7 /TP7 /TIOCB2 /A 20
PA6 /TP6 /TIOCA2 /A21
PA5 /TP5 /TIOCB1 /A 22
PA4 /TP4 /TIOCA1 /A23
Port A
PA3 /TP3 /TIOCB0 /TCLKD
PA2 /TP2 /TIOCA0 /TCLKC
PA1 /TP1 /TEND1 /TCLKB
PA0 /TP0 /TEND0 /TCLKA
Pin functions in modes 1, 2, 6, and 7
PA 7 (input/output)/TP7 (output)/TIOCB 2 (input/output)
PA 6 (input/output)/TP6 (output)/TIOCA 2 (input/output)
PA 5 (input/output)/TP5 (output)/TIOCB 1 (input/output)
PA 4 (input/output)/TP4 (output)/TIOCA 1 (input/output)
PA 3 (input/output)/TP3 (output)/TIOCB 0 (input/output)/TCLKD (input)
PA 2 (input/output)/TP2 (output)/TIOCA 0 (input/output)/TCLKC (input)
PA 1 (input/output)/TP1 (output)/TEND 1 (output)/TCLKB (input)
PA 0 (input/output)/TP0 (output)/TEND 0 (output)/TCLKA (input)
Pin functions in modes 3, 4
A 20 (output)
PA 6 (input/output)/TP6 (output)/TIOCA 2 (input/output)/A 21 (output)
PA 5 (input/output)/TP5 (output)/TIOCB 1 (input/output)/A 22 (output)
PA 4 (input/output)/TP4 (output)/TIOCA 1 (input/output)/A 23 (output)
PA 3 (input/output)/TP3 (output)/TIOCB 0 (input/output)/TCLKD (input)
PA 2 (input/output)/TP2 (output)/TIOCA 0 (input/output)/TCLKC (input)
PA 1 (input/output)/TP1 (output)/TEND 1 (output)/TCLKB (input)
PA 0 (input/output)/TP0 (output)/TEND 0 (output)/TCLKA (input)
Pin functions in mode 5
PA7 (input/output)/TP7 (output)/TIOCB2 (input/output)/A 20 (output)
PA6 (input/output)/TP6 (output)/TIOCA2 (input/output)/A 21 (output)
PA5 (input/output)/TP5 (output)/TIOCB1 (input/output)/A 22 (output)
PA4 (input/output)/TP4 (output)/TIOCA1 (input/output)/A 23 (output)
PA3 (input/output)/TP3 (output)/TIOCB0 (input/output)/TCLKD (input)
PA2 (input/output)/TP2 (output)/TIOCA0 (input/output)/TCLKC (input)
PA1 (input/output)/TP1 (output)/TEND1 (output)/TCLKB (input)
PA0 (input/output)/TP0 (output)/TEND0 (output)/TCLKA (input)
Figure 8.10 Port A Pin Configuration
Rev. 3.00 Sep 14, 2005 page 301 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.11.2
Register Descriptions
Table 8.18 summarizes the registers of port A.
Table 8.18 Port A Registers
Initial Value
Address*
Name
H'EE009
Port A data direction
register
H'FFFD9
Port A data register
R/W
Modes 1, 2, 5, 6, and 7
Modes 3, 4
PADDR
W
H'00
H'80
PADR
R/W
H'00
H'00
Note: * Lower 20 bits of the address in advanced mode.
Port A Data Direction Register (PADDR): PADDR is an 8-bit write-only register that can
select input or output for each pin in port A. When pins are used for TPC output, the
corresponding PADDR bits must also be set.
Bit
7
6
5
4
3
2
1
0
PA7 DDR PA6 DDR PA5 DDR PA4 DDR PA3 DDR PA2 DDR PA1 DDR PA0 DDR
Modes Initial value 1
3, 4
Read/Write —
Modes Initial value 0
1, 2, 5,
6 and 7 Read/Write W
0
0
0
0
0
0
0
W
W
W
W
W
W
W
0
0
0
0
0
0
0
W
W
W
W
W
W
W
Port A data direction 7 to 0
These bits select input or output for port A pins
The pin functions that can be selected for pins PA7 to PA4 differ between modes 1, 2, 6, and 7,
and modes 3 to 5. For the method of selecting the pin functions, see tables 8.19 and 8.20.
The pin functions that can be selected for pins PA3 to PA0 are the same in modes 1 to 7. For the
method of selecting the pin functions, see table 8.21.
When port A functions as an input/output port, a pin in port A becomes an output port if the
corresponding PADDR bit is set to 1, and an input port if this bit is cleared to 0. In modes 3 and
4, PA7DDR is fixed at 1 and PA7 functions as the A20 address output pin.
PADDR is a write-only register. Its value cannot be read. All bits return 1 when read.
Rev. 3.00 Sep 14, 2005 page 302 of 910
REJ09B0258-0300
Section 8 I/O Ports
PADDR is initialized to H'00 by a reset and in hardware standby mode in modes 1, 2, 5, 6, and 7.
It is initialized to H'80 by a reset and in hardware standby mode in modes 3 and 4. In software
standby mode it retains its previous setting. Therefore, if a transition is made to software standby
mode while port A is functioning as an input/output port and a PADDR bit is set to 1, the
corresponding pin maintains its output state.
Port A Data Register (PADR): PADR is an 8-bit readable/writable register that stores output
data for port A. When port A functions as an output port, the value of this register is output.
When a bit in PADDR is set to 1, if port A is read the value of the corresponding PADR bit is
returned. When a bit in PADDR is cleared to 0, if port A is read the corresponding pin logic level
is read.
Bit
7
6
5
4
3
2
1
0
PA 7
PA 6
PA 5
PA 4
PA 3
PA 2
PA 1
PA 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port A data 7 to 0
These bits store data for port A pins
PADR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 303 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.19 Port A Pin Functions (Modes 1, 2, 6, 7)
Pin
Pin Functions and Selection Method
PA7/TP7/
TIOCB2
Bit PWM2 in TMDR, bits IOB2 to IOB0 in TIOR2, bit NDER7 in NDERA, and bit PA7DDR select the pin
function as follows.
16-bit timer channel 2
settings
(1) in table below
PA7DDR
(2) in table below
—
NDER7
Pin function
0
1
—
—
0
1
TIOCB2 output
PA7 input
PA7 output
TP7 output
TIOCB2 input*
Note: * TIOCB2 input when IOB2 = 1 and PWM2 = 0.
16-bit timer channel 2
settings
1
(2)
IOB2
(1)
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
Rev. 3.00 Sep 14, 2005 page 304 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
PA6/TP6/
TIOCA2
Bit PWM2 in TMDR, bits IOA2 to IOA0 in TIOR2, bit NDER6 in NDERA, and bit PA6DDR select the pin
function as follows.
16-bit timer channel 2
settings
(1) in table below
(2) in table below
PA6DDR
—
0
1
1
NDER6
—
—
0
1
TIOCA2 output
PA6 input
PA6 output
TP6 output
Pin function
TIOCA2 input*
Note: * TIOCA2 input when IOA2 = 1.
16-bit timer channel 2
settings
(2)
(1)
PWM2
(1)
0
IOA2
PA5/TP5/
TIOCB1
(2)
1
1
—
IOA1
0
0
0
1
—
—
IOA0
0
1
—
—
—
Bit PWM1 in TMDR, bits IOB2 to IOB0 in TIOR1, bit NDER5 in NDERA, and bit PA5DDR select the pin
function as follows.
16-bit timer channel 1
settings
(1) in table below
PA5DDR
—
NDER5
Pin function
(2) in table below
0
1
1
—
—
0
1
TIOCB1 output
PA5 input
PA5 output
TP5 output
TIOCB1 input*
Note: * TIOCB1 input when IOB2 = 1 and PWM1 = 0.
16-bit timer channel 1
settings
(2)
IOB2
(1)
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
Rev. 3.00 Sep 14, 2005 page 305 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
PA4/TP4/
TIOCA1
Bit PWM1 in TMDR, bits IOA2 to IOA0 in TIOR1, bit NDER4 in NDERA, and bit PA4DDR select the pin
function as follows.
16-bit timer channel 1
settings
(1) in table below
(2) in table below
PA4DDR
—
0
1
1
NDER4
—
—
0
1
TIOCA1 output
PA4 input
PA4 output
TP4 output
Pin function
TIOCA1 input*
Note: * TIOCA1 input when IOA2 = 1.
16-bit timer channel 1
settings
(2)
(1)
PWM1
(2)
0
IOA2
(1)
1
1
—
IOA1
0
0
0
1
—
—
IOA0
0
1
—
—
—
Rev. 3.00 Sep 14, 2005 page 306 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.20 Port A Pin Functions (Modes 3, 4, 5)
Pin
Pin Functions and Selection Method
PA7/TP7/
Modes 3 and 4: Always used as A20 output.
TIOCB2/ A20
Pin function
A20 output
Mode 5:
Bit PWM2 in TMDR, bits IOB2 to IOB0 in TIOR2, bit NDER7 in NDERA, bit A20E in BRCR, and bit PA 7DDR
select the pin function as follows.
A20E
16-bit timer channel 2
settings
1
(1) in table below
0
(2) in table below
—
PA7DDR
—
0
1
1
—
NDER7
—
—
0
1
—
TIOCB2 output
PA7 input
PA7 output
TP7 output
A20 output
Pin function
TIOCB2 input*
Note: * TIOCB2 input when IOB2 = 1 and PWM2 = 0.
16-bit timer channel 2 settings
(2)
(1)
IOB2
PA6/TP6/
TIOCA2/A21
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
Bit PWM2 in TMDR, bits IOA2 to IOA0 in TIOR2, bit NDER6 in NDERA, bit A21E in BRCR, and bit PA 6DDR
select the pin function as follows.
A21E
16-bit timer channel 2
settings
1
(1) in table below
0
(2) in table below
—
PA6DDR
—
0
1
1
—
NDER6
—
—
0
1
—
TIOCA2 output
PA6 input
PA6 output
TP6 output
A21 output
Pin function
TIOCA2 input*
Note: * TIOCA2 input when IOA2 = 1.
16-bit timer channel 2 settings
(2)
(1)
PWM2
(2)
0
IOA2
(1)
1
1
—
IOA1
0
0
0
1
—
—
IOA0
0
1
—
—
—
Rev. 3.00 Sep 14, 2005 page 307 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
PA5/TP5/
TIOCB1/A22
Bit PWM1 in TMDR, bits IOB2 to IOB0 in TIOR1, bit NDER5 in NDERA, bit A22E in BRCR, and bit PA5DDR
select the pin function as follows.
A22E
16-bit timer channel 1
settings
1
(1) in table below
0
(2) in table below
—
PA5DDR
—
0
1
1
—
NDER5
—
—
0
1
—
TIOCB1 output
PA5 input
PA5 output
TP5 output
A22 output
Pin function
TIOCB1 input*
Note: * TIOCB1 input when IOB2 = 1 and PWM1 = 0.
16-bit timer channel 1
settings
(2)
(1)
IOB2
PA4/TP4/
TIOCA1/A23
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
Bit PWM1 in TMDR, bits IOA2 to IOA0 in TIOR1, bit NDER4 in NDERA, bit A23E in BRCR, and bit PA4DDR
select the pin function as follows.
A23E
16-bit timer channel 1
settings
1
(1) in table below
0
(2) in table below
—
PA4DDR
—
0
1
1
—
NDER4
—
—
0
1
—
TIOCA1 output
PA4 input
PA4 output
TP4 output
A23 output
Pin function
TIOCA1 input*
Note: * TIOCA1 input when IOA2 = 1.
16-bit timer channel 1
settings
(2)
(1)
PWM1
(2)
(1)
1
—
0
IOA2
1
0
IOA1
0
0
1
—
—
IOA0
0
1
—
—
—
Rev. 3.00 Sep 14, 2005 page 308 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.21 Port A Pin Functions (Modes 1 to 7)
Pin
Pin Functions and Selection Method
PA3/TP3/
TIOCB0/
TCLKD
Bit PWM0 in TMDR, bits IOB2 to IOB0 in TIOR0, bits TPSC2 to TPSC0 in 16TCR2 to 16TCR0 of the 16-bit
timer, bits CKS2 to CKS0 in 8TCR2 of the 8-bit timer, bit NDER3 in NDERA, and bit PA3DDR select the pin
function as follows.
16-bit timer channel 0
settings
(1) in table below
(2) in table below
PA3DDR
—
0
1
1
NDER3
—
—
0
1
TIOCB0
output
PA3
input
PA3
output
TP3
output
Pin function
TIOCB0 input*1
TCLKD input*2
Notes:
1.
TIOCB0 input when IOB2 = 1 and PWM0 = 0.
2.
TCLKD input when TPSC2 = TPSC1 = TPSC0 = 1 in any of 16TCR2 to 16TCR0, or bits CKS2
to CKS0 in 8TCR2 are as shown in (3) in the table below.
16-bit timer channel 0
settings
(2)
(1)
IOB2
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
8-bit timer channel 2
settings
(4)
CKS2
0
CKS1
—
CKS0
—
(3)
1
0
0
1
1
—
Rev. 3.00 Sep 14, 2005 page 309 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
PA2/TP2/
TIOCA0/
TCLKC
Bit PWM0 in TMDR, bits IOA2 to IOA0 in TIOR0, bits TPSC2 to TPSC0 in 16TCR2 to 16TCR0 of the 16-bit
timer, bits CKS2 to CKS0 in 8TCR0 of the 8-bit timer, bit NDER2 in NDERA, and bit PA2DDR select the pin
function as follows.
16-bit timer channel 0
settings
(1) in table below
PA2DDR
(2) in table below
—
NDER2
Pin function
0
1
1
—
—
0
1
TIOCA0 output
PA2
input
PA2 output
TP2 output
TIOCA0 input*1
TCLKC input*2
Notes:
1.
TIOCA0 input when IOA2 = 1.
2.
TCLKC input when TPSC2 = TPSC1 = 1 and TPSC0 = 0 in any of 16TCR2 to 16TCR0, or bits
CKS2 to CKS0 in 8TCR0 are as shown in (3) in the table below.
16-bit timer channel 0
settings
(2)
(1)
PWM0
(2)
(1)
1
—
0
IOA2
1
0
IOA1
0
0
1
—
—
IOA0
0
1
—
—
—
8-bit timer channel 0
settings
(4)
CKS2
0
CKS1
—
CKS0
—
Rev. 3.00 Sep 14, 2005 page 310 of 910
REJ09B0258-0300
(3)
1
0
0
1
1
—
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
PA1/TP1/
TCLKB/
Bit MDF in TMDR, bits TPSC2 to TPSC0 in 16TCR2 to 16TCR0 of the 16-bit timer, bits CKS2 to CKS0 in
8TCR3 of the 8-bit timer, bit NDER1 in NDERA, and bit PA1DDR select the pin function as follows.
TEND1
PA1DDR
0
1
NDER1
—
0
1
PA1 input
PA1 output
TP1 output
Pin function
1
TCLKB output*1
TEND1 output*2
Notes:
1.
TCLKB input when MDF = 1 in TMDR, or TPSC2 = 1, TPSC1 = 0, and TPSC0 = 1 in any of
16TCR2 to 16TCR0, or bits CKS2 to CKS0 in 8TCR3 are as shown in (1) in the table below.
2.
When an external request is specified as a DMAC activation source, TEND1 output regardless
of bits PA1DDR and NDER1.
8-bit timer channel 3
settings
PA0/TP0/
TCLKA/
(2)
CKS2
0
CKS1
—
CKS0
—
(1)
1
0
0
1
1
—
Bit MDF in TMDR, bits TPSC2 to TPSC0 in 16TCR2 to 16TCR0 of the 16-bit timer, bits CKS2 to CKS0 in
8TCR1 of the 8-bit timer, bit NDER0 in NDERA, and bit PA0DDR select the pin function as follows.
TEND0
PA0DDR
0
NDER0
—
Pin function
1
PA0 input
0
1
PA0 output
TP0 output
TCLKA output*1
TEND0 output*2
Notes:
1.
TCLKA input when MDF = 1 in TMDR, or TPSC2 = 1, TPSC1 = 0 and TPSC0 = 0 in any of
16TCR2 to 16TCR0, or bits CKS2 to CKS0 in 8TCR0 are as shown in (1) in the table below.
2.
When an external request is specified as a DMAC activation source, TEND0 output regardless
of bits PA0DDR and NDER0.
8-bit timer channel 1
settings
(2)
CKS2
0
CKS1
—
CKS0
—
(1)
1
0
0
1
1
—
Rev. 3.00 Sep 14, 2005 page 311 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.12
Port B
8.12.1
Overview
Port B is an 8-bit input/output port that is also used for output (TP15 to TP8) from the
programmable timing pattern controller (TPC), input/output (TMIO3, TMO2, TMIO1, TMO0) by
the 8-bit timer, CS7 to CS4 output, input (DREQ1, DREQ0) to the DMA controller (DMAC), input
and output (TxD2, RxD2, SCK2) by serial communication interface channel 2 (SCI2), and output
(UCAS, LCAS) by the DRAM interface. See table 8.23 to 8.24 for the selection of pin functions.
A reset or hardware standby transition leaves port B as an input port.
For output of CS7 to CS4 in modes 1 to 5, see section 6.3.4, Chip Select Signals. When DRAM is
connected to areas 2, 3, 4, and 5, the CS4 and CS5 output pins become RAS output pins for these
areas. For details see section 6.5, DRAM Interface. Pins not assigned to any of these functions
are available for generic input/output. Figure 8.11 shows the pin configuration of port B.
When DRAM is connected to areas 2, 3, 4, and 5, the CS4 and CS5 output pins become RAS
output pins for these areas. For details see 6.5, DRAM Interface.
Pins in port B can drive one TTL load and a 30-pF capacitive load. They can also drive darlington
transistor pair.
Rev. 3.00 Sep 14, 2005 page 312 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port B pins
PB7/TP15 /RxD2
PB6/TP14 /TxD2
PB5/TP13 /SCK2/LCAS
PB4/TP12 /UCAS
Port B
PB3/TP11 /TMIO3/DREQ1/CS4
PB2/TP10 /TMO2/CS5
PB1/TP9 /TMIO1/DREQ0/CS6
PB0/TP8 /TMO0/CS7
Pin functions in modes 1 to 5
PB7 (input/output)/TP15 (output) /RxD2 (input)
PB6 (input/output)/TP14 (output) /TxD2 (output)
PB5 (input/output)/TP13 (output) /SCK2 (input/output) /LCAS (output)
PB4 (input/output)/TP12 (output) /UCAS (output)
PB3 (input/output)/TP11 (output) /TMIO3 (input/output) /DREQ1 (input) CS4 (output)
PB2 (input/output)/TP10 (output) /TMO2 (output) /CS5 (output)
PB1 (input/output)/TP9 (output) /TMIO1 (input/output) /DREQ0 (input) /CS6 (output)
PB0 (input/output)/TP8 (output) /TMO0 (output) /CS7 (output)
Pin functions in mode 6 and 7
PB7 (input/output)/TP15 (output) /RxD2 (input)
PB6 (input/output)/TP14 (output) /TxD2 (output)
PB5 (input/output)/TP13 (output) /SCK2 (input/output)
PB4 (input/output)/TP12 (output)
PB3 (input/output)/TP11 (output) /TMIO3 (input/output) /DREQ1 (input)
PB2 (input/output)/TP10 (output) /TMO2 (output)
PB1 (input/output)/TP9 (output) /TMIO1 (input/output) /DREQ0 (input)
PB0 (input/output)/TP8 (output) /TMO0 (output)
Figure 8.11 Port B Pin Configuration
Rev. 3.00 Sep 14, 2005 page 313 of 910
REJ09B0258-0300
Section 8 I/O Ports
8.12.2
Register Descriptions
Table 8.22 summarizes the registers of port B.
Table 8.22 Port B Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'EE00A
Port B data direction register
PBDDR
W
H'00
H'FFFDA
Port B data register
PBDR
R/W
H'00
Note: * Lower 20 bits of the address in advanced mode.
Port B Data Direction Register (PBDDR): PBDDR is an 8-bit write-only register that can
select input or output for each pin in port B. When pins are used for TPC output, the
corresponding PBDDR bits must also be set.
Bit
7
6
5
4
3
2
1
0
PB7 DDR PB6 DDR PB5 DDR PB4 DDR PB3 DDR PB2 DDR PB1 DDR PB0 DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port B data direction 7 to 0
These bits select input or output for port B pins
The pin functions that can be selected for port B differ between modes 1 to 5, and modes 6 and 7.
For the method of selecting the pin functions, see tables 8.23 and 8.24.
When port B functions as an input/output port, a pin in port B becomes an output port if the
corresponding PBDDR bit is set to 1, and an input port if this bit is cleared to 0.
PBDDR is a write-only register. Its value cannot be read. All bits return 1 when read.
PBDDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode
it retains its previous setting. Therefore, if a transition is made to software standby mode while
port B is functioning as an input/output port and a PBDDR bit is set to 1, the corresponding pin
maintains its output state.
Rev. 3.00 Sep 14, 2005 page 314 of 910
REJ09B0258-0300
Section 8 I/O Ports
Port B Data Register (PBDR): PBDR is an 8-bit readable/writable register that stores output
data for pins port B. When port B functions as an output port, the value of this register is output.
When a bit in PBDDR is set to 1, if port B is read the value of the corresponding PBDR bit is
returned. When a bit in PBDDR is cleared to 0, if port B is read the corresponding pin logic level
is read.
Bit
7
6
5
4
3
2
1
0
PB 7
PB 6
PB 5
PB 4
PB 3
PB 2
PB 1
PB 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port B data 7 to 0
These bits store data for port B pins
PBDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
Rev. 3.00 Sep 14, 2005 page 315 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.23 Port B Pin Functions (Modes 1 to 5)
Pin
Pin Functions and Selection Method
PB7/TP15/
RxD2
Bit RE in SCR of SCI2, bit SMIF in SCMR, bit NDER15 in NDERB, and bit PB7DDR select the pin function as
follows.
SMIF
0
RE
0
1
—
PB7DDR
0
1
1
—
—
NDER15
—
0
1
—
—
PB7 input
PB7 output
TP15 output
RxD2 input
RxD2 input
Pin function
PB6/TP14/
TxD2
1
Bit TE in SCR of SCI2, bit SMIF in SCMR, bit NDER14 in NDERB, and bit PB6DDR select the pin function as
follows.
SMIF
0
TE
1
0
PB6DDR
NDER14
Pin function
0
1
1
1
—
—
—
—
0
1
—
—
PB6 input
PB6 output
TP14 output
TxD2 output
TxD2 output*
Note: * Functions as the TxD2 output pin, but there are two states: one in which the pin is driven, and
another in which the pin is at high-impedance.
PB5/TP13/
Bit C/A in SMR of SCI2, bits CKE0 and CKE1 in SCR, bit NDER13 in NDERB, and bit PB5DDR select the pin
SCK2/LCAS function as follows.
CKE1
0
C/A
0
CKE0
PB5DDR
NDER13
Pin function
1
0
0
1
1
—
0
1
PB5 input
PB5 output
TP13 output
1
—
1
—
—
—
—
—
—
—
—
SCK2 output SCK2 output
SCK2 input
LCAS output*
Note: * LCAS output depending on bits DRAS2 to DRAS0 in DRCRA and bit CSEL in DRCRB, and
regardless of bits C/A, CKE0, and CKE1, NDER13, and PB5DDR. For details, see section 6, Bus
Controller.
PB4/TP12/
UCAS
Bit NDER12 in NDERB and bit PB4DDR select the pin function as follows.
PB4DDR
0
1
1
NDER12
—
0
1
PB4 output
TP12 output
Pin function
PB4 input
UCAS output*
Note: * UCAS output depending on bits DRAS2 to DRAS0 in DRCRA and bit CSEL in DRCRB, and
regardless of bits NDER12 and PB4DDR. For details, see section 6, Bus Controller.
Rev. 3.00 Sep 14, 2005 page 316 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
The DRAM interface settings by bits DRAS2 to DRAS0 in DRCRA, bits OIS3/2 and OS1/0 in 8TCSR3, bits
PB3/TP11/
TMIO3/
CCLR1 and CCLR0 in 8TCR3, bit CS4E in CSCR, bit NDER11 in NDERB, and bit PB3DDR select the pin
DREQ1/CS4 function as follows.
DRAM interface
settings
(1) in table below
OIS3/2 and OS1/0
(2) in table
below
All 0
CS4E
0
Not all 0
—
—
1
—
PB3DDR
0
1
1
—
—
—
NDER11
—
0
1
—
—
—
PB3
input
PB3
output
TP11
output
CS4
output
TMIO3
output
output*3
Pin function
CS4
TMIO3 input*1
DREQ1 input*2
Notes:
1.
TMIO3 input when CCLR1 = CCLR0 = 1.
2.
When an external request is specified as a DMAC activation source, DREQ1 input regardless
3.
CS4 is output as RAS4.
of bits OIS3 and OIS2, OS1 and OS0, CCLR1 and CCLR0, CS4E, NDER11, and PB3DDR.
DRAM interface
settings
(1)
DRAS2
0
DRAS1
DRAS0
PB2/TP10/
TMO2/CS5
(2)
1
0
0
1
1
(1)
0
0
1
0
1
1
0
1
The DRAM interface settings by bits DRAS2 to DRAS0 in DRCRA, bits OIS3/2 and OS1/0 in 8TCSR2, bit
CS5E in CSCR, bit NDER10 in NDERB, and bit PB2DDR select the pin function as follows.
DRAM interface
settings
(1) in table below
OIS3/2 and OS1/0
All 0
CS5E
0
PB2DDR
0
NDER10
Pin function
(2) in table
below
1
1
Not all 0
—
1
—
—
—
—
—
—
0
1
—
—
—
PB2
input
PB2
output
TP10
output
CS5
TMIO2
output
CS5
output
output*
Note: * CS5 is output as RAS5.
DRAM interface
settings
(1)
DRAS2
0
DRAS1
DRAS0
(2)
1
0
0
1
1
(1)
0
0
1
0
1
1
0
1
Rev. 3.00 Sep 14, 2005 page 317 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
Bits OIS3/2 and OS1/0 in 8TCSR1, bits CCLR1 and CCLR0 in TCR1, bit CS6E in CSCR, bit NDER9 in
PB1/TP9/
TMIO1/
NDERB, and bit PB1DDR select the pin function as follows.
DREQ0/CS6
OIS3/2 and OS1/0
All 0
CS6E
Not all 0
0
PB1DDR
0
1
1
1
—
—
—
NDER9
—
0
1
—
—
Pin function
PB1
input
PB1
output
TP9
output
CS6
TMIO1 output
output
TMIO1 input*1
DREQ0 input*2
Notes:
1.
TMIO1 input when CCLR1 = CCLR0 = 1.
2.
When an external request is specified as a DMAC activation source, DREQ0 input regardless
of bits OIS3/2 and OS1/0, bits CCLR1/0, bit CS6E, bit NDER9, and bit PB1DDR.
PB0/TP8/
TMO0/CS7
Bits OIS3/2 and OS1/0 in 8TCSR0, bit CS7E in CSCR, bit NDER8 in NDERB, and bit PB0DDR select the pin
function as follows.
OIS3/2 and OS1/0
All 0
CS7E
Not all 0
1
—
PB0DDR
0
1
1
—
—
NDER8
—
0
1
—
—
PB0 input
PB0 output
TP8 output
CS7 output
TMO0 output
Pin function
0
Rev. 3.00 Sep 14, 2005 page 318 of 910
REJ09B0258-0300
Section 8 I/O Ports
Table 8.24 Port B Pin Functions (Modes 6 and 7)
Pin
Pin Functions and Selection Method
PB7/TP15/
RxD2
Bit RE in SCR of SCI2, bit SMIF in SCMR, bit NDER15 in NDERB, and bit PB7DDR select the pin function as
follows.
SMIF
0
RE
1
—
PB7DDR
0
1
0
1
—
—
NDER15
—
0
1
—
—
PB7 input
PB7 output
TP15 output
RxD2 input
RxD2 input
Pin function
PB6/TP14/
TxD2
1
Bit TE in SCR of SCI2, bit SMIF in SCMR, bit NDER14 in NDERB, and bit PB6DDR select the pin function as
follows.
SMIF
0
TE
1
0
PB6DDR
0
NDER14
Pin function
1
1
1
—
—
—
—
0
1
—
—
PB6 input
PB6 output
TP14 output
TxD2 output
TxD2 output*
Note: * Functions as the TxD2 output pin, but there are two states: one in which the pin is driven, and
another in which the pin is at high-impedance.
PB5/TP13/
SCK2
Bit C/A in SMR of SCI2, bits CKE0 and CKE1 in SCR, bit NDER13 in NDERB, and bit PB5DDR select the pin
function as follows.
CKE1
0
C/A
0
CKE0
0
1
—
—
1
—
PB5DDR
0
1
1
—
—
—
NDER13
—
0
1
—
—
—
PB5 input
PB5 output
TP13 output
Pin function
PB4/TP12
1
SCK2 output SCK2 output
SCK2 input
Bit NDER12 in NDERB and bit PB4DDR select the pin function as follows.
PB4DDR
0
1
NDER12
—
0
1
PB4 input
PB4 output
TP12 output
Pin function
1
Rev. 3.00 Sep 14, 2005 page 319 of 910
REJ09B0258-0300
Section 8 I/O Ports
Pin
Pin Functions and Selection Method
PB3/TP11/
TMIO3/
Bits OIS3/2 and OS1/0 in TCSR3, bits CCLR1 and CCLR0 in TCR3, bit NDER11 in NDERB, and bit PB3DDR
select the pin function as follows.
DREQ1
OIS3/2 and OS1/0
All 0
Not all 0
PB3DDR
0
1
1
—
NDER11
—
0
1
—
PB3 input
PB3 output
TP11 output
TMIO3 output
Pin function
1
TMIO3 input*
DREQ1 input*2
Notes:
1.
TMIO3 input when CCLR1 = CCLR0 = 1.
2.
When an external request is specified as a DMAC activation source, DREQ1 input regardless
of bits OIS3/2 and OS1/0, bit NDER11, and bit PB3DDR.
PB2/TP10/
TMO2
Bits OIS3/2 and OS1/0 in TCSR2, bit NDER10 in NDERB, and bit PB2DDR select the pin function as follows.
OIS3/2 and OS1/0
All 0
Not all 0
PB2DDR
0
1
1
—
NDER10
—
0
1
—
PB2 input
PB2 output
TP10 output
TMO2 output
Pin function
PB1/TP9/
TMIO1/
Bits OIS3/2 and OS1/0 in TCSR1, bits CCLR1 and CCLR0 in TCR1, bit NDER9 in NDERB, and bit PB1DDR
select the pin function as follows.
DREQ0
OIS3/2 and OS1/0
All 0
Not all 0
PB1DDR
0
1
1
—
NDER9
—
0
1
—
PB1
input
PB1
output
TP9
output
TMIO1
output
Pin function
TMIO1 input*1
DREQ0 input*2
Notes:
1.
TMIO1 input when CCLR1 = CCLR0 = 1.
2.
When an external request is specified as a DMAC activation source, DREQ0 input regardless
of bits OIS3/2 and OS1/0, bit NDER9, and bit PB1DDR.
PB0/TP8/
TMO0
Bits OIS3/2 and OS1/0 in TCSR0, bit NDER8 in NDERB, and bit PB0DDR select the pin function as follows.
OIS3/2 and OS1/0
All 0
Not all 0
PB0DDR
0
1
1
—
NDER8
—
0
1
—
PB0
input
PB0
output
TP8
output
TMO0
output
Pin function
Rev. 3.00 Sep 14, 2005 page 320 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Section 9 16-Bit Timer
9.1
Overview
The H8/3068F has built-in 16-bit timer module with three 16-bit counter channels.
9.1.1
Features
16-bit timer features are listed below.
• Capability to process up to 6 pulse outputs or 6 pulse inputs
• Six general registers (GRs, two per channel) with independently-assignable output compare or
input capture functions
• Selection of eight counter clock sources for each channel:
Internal clocks: φ, φ/2, φ/4, φ/8
External clocks: TCLKA, TCLKB, TCLKC, TCLKD
• Five operating modes selectable in all channels:
 Waveform output by compare match
Selection of 0 output, 1 output, or toggle output (only 0 or 1 output in channel 2)
 Input capture function
Rising edge, falling edge, or both edges (selectable)
 Counter clearing function
Counters can be cleared by compare match or input capture
 Synchronization
Two or more timer counters (16TCNTs) can be preset simultaneously, or cleared
simultaneously by compare match or input capture. Counter synchronization enables
synchronous register input and output.
 PWM mode
PWM output can be provided with an arbitrary duty cycle. With synchronization, up to
three-phase PWM output is possible
• Phase counting mode selectable in channel 2
Two-phase encoder output can be counted automatically.
• High-speed access via internal 16-bit bus
The 16TCNTs and GRs can be accessed at high speed via a 16-bit bus.
• Any initial timer output value can be set
Rev. 3.00 Sep 14, 2005 page 321 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
• Nine interrupt sources
Each channel has two compare match/input capture interrupts and an overflow interrupt. All
interrupts can be requested independently.
• Output triggering of programmable timing pattern controller (TPC)
Compare match/input capture signals from channels 0 to 2 can be used as TPC output
triggers.
Table 9.1 summarizes the 16-bit timer functions.
Table 9.1
16-bit timer Functions
Item
Channel 0
Channel 1
Clock sources
Internal clocks: φ, φ/2, φ/4, φ/8
Channel 2
External clocks: TCLKA, TCLKB, TCLKC, TCLKD, selectable independently
General registers (output
compare/input
capture registers)
GRA0, GRB0
GRA1, GRB1
GRA2, GRB2
Input/output pins
Counter clearing function
TIOCA0, TIOCB0
TIOCA1, TIOCB1
TIOCA2, TIOCB2
GRA0/GRB0 compare
match or input capture
GRA1/GRB1 compare
match or input capture
GRA2/GRB2 compare
match or input capture
Initial output value setting function
Available
Available
Available
Compare match
output
0
Available
Available
Available
1
Available
Available
Available
Toggle
Available
Available
Not available
Input capture function
Available
Available
Available
Synchronization
Available
Available
Available
PWM mode
Available
Available
Available
Phase counting mode
Not available
Not available
Available
Interrupt sources
Three sources
Three sources
Three sources
• Compare match/input
capture A0
• Compare match/input
capture A1
• Compare match/input
capture A2
• Compare match/input
capture B0
• Compare match/input
capture B1
• Compare match/input
capture B2
• Overflow
• Overflow
• Overflow
Rev. 3.00 Sep 14, 2005 page 322 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.1.2
Block Diagrams
16-bit timer Block Diagram (Overall): Figure 9.1 is a block diagram of the 16-bit timer.
TCLKA to TCLKD
IMIA0 to IMIA2
IMIB0 to IMIB2
OVI0 to OVI2
Clock selector
φ, φ/2, φ/4, φ/8
Control logic
TIOCA0 to TIOCA2
TIOCB0 to TIOCB2
TOLR
TISRA
TISRB
Internal data bus
TMDR
Bus interface
TSNR
16-bit timer channel 0
16-bit timer channel 1
16-bit timer channel 2
TSTR
TISRC
Module data bus
Legend:
TSTR: Timer start register (8 bits)
TSNR: Timer synchro register (8 bits)
TMDR: Timer mode register (8 bits)
TOLR: Timer output level setting register (8 bits)
TISRA: Timer interrupt status register A (8 bits)
TISRB: Timer interrupt status register B (8 bits)
TISRC: Timer interrupt status register C (8 bits)
Figure 9.1 16-bit timer Block Diagram (Overall)
Rev. 3.00 Sep 14, 2005 page 323 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Block Diagram of Channels 0 and 1: 16-bit timer channels 0 and 1 are functionally identical.
Both have the structure shown in figure 9.2.
TCLKA to TCLKD
φ, φ/2, φ/4, φ/8
TIOCA0
TIOCB0
Clock selector
Control logic
IMIA0
IMIB0
OVI0
TIOR
16TCR
GRB
GRA
16TCNT
Comparator
Module data bus
Legend:
16TCNT:
GRA, GRB:
TCR:
TIOR:
Timer counter (16 bits)
General registers A and B (input capture/output compare registers) (16 bits × 2)
Timer control register (8 bits)
Timer I/O control register (8 bits)
Figure 9.2 Block Diagram of Channels 0 and 1
Rev. 3.00 Sep 14, 2005 page 324 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Block Diagram of Channel 2: Figure 9.3 is a block diagram of channel 2
TCLKA to TCLKD
φ, φ/2, φ/4, φ/8
TIOCA2
TIOCB2
Clock selector
Control logic
IMIA2
IMIB2
OVI2
TIOR2
16TCR2
GRB2
GRA2
16TCNT2
Comparator
Module data bus
Legend:
Timer counter 2 (16 bits)
16TCNT2:
GRA2, GRB2: General registers A2 and B2 (input capture/output compare registers)
(16 bits × 2)
Timer control register 2 (8 bits)
TCR2:
Timer I/O control register 2 (8 bits)
TIOR2:
Figure 9.3 Block Diagram of Channel 2
Rev. 3.00 Sep 14, 2005 page 325 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.1.3
Pin Configuration
Table 9.2 summarizes the 16-bit timer pins.
Table 9.2
16-bit timer Pins
Abbreviation
Input/
Output
Common Clock input A
TCLKA
Input
External clock A input pin
(phase-A input pin in phase counting
mode)
Clock input B
TCLKB
Input
External clock B input pin
(phase-B input pin in phase counting
mode)
Clock input C
TCLKC
Input
External clock C input pin
Clock input D
TCLKD
Input
External clock D input pin
Input capture/output TIOCA0
compare A0
Input/
output
GRA0 output compare or input capture pin
PWM output pin in PWM mode
Input capture/output TIOCB0
compare B0
Input/
output
GRB0 output compare or input capture pin
Input capture/output TIOCA1
compare A1
Input/
output
GRA1 output compare or input capture pin
PWM output pin in PWM mode
Input capture/output TIOCB1
compare B1
Input/
output
GRB1 output compare or input capture pin
Input capture/output TIOCA2
compare A2
Input/
output
GRA2 output compare or input capture pin
PWM output pin in PWM mode
Input capture/output TIOCB2
compare B2
Input/
output
GRB2 output compare or input capture pin
Channel
0
1
2
Name
Rev. 3.00 Sep 14, 2005 page 326 of 910
REJ09B0258-0300
Function
Section 9 16-Bit Timer
9.1.4
Register Configuration
Table 9.3 summarizes the 16-bit timer registers.
Table 9.3
16-bit timer Registers
Channel
Address*1
Name
Abbreviation
R/W
Initial
Value
Common
H'FFF60
Timer start register
TSTR
R/W
H'F8
H'FFF61
Timer synchro register
TSNC
R/W
H'F8
H'FFF62
Timer mode register
TMDR
R/W
H'98
H'FFF63
Timer output level setting register
TOLR
W
H'FFF64
H'FFF65
0
1
Timer interrupt status register A
Timer interrupt status register B
TISRA
TISRB
H'C0
2
H'88
2
H'88
2
R/(W)*
R/(W)*
H'FFF66
Timer interrupt status register C
TISRC
R/(W)*
H'88
H'FFF68
Timer control register 0
16TCR0
R/W
H'80
H'FFF69
Timer I/O control register 0
TIOR0
R/W
H'88
H'FFF6A
Timer counter 0H
16TCNT0H R/W
H'00
H'FFF6B
Timer counter 0L
16TCNT0L R/W
H'00
H'FFF6C
General register A0H
GRA0H
R/W
H'FF
H'FFF6D
General register A0L
GRA0L
R/W
H'FF
H'FFF6E
General register B0H
GRB0H
R/W
H'FF
H'FFF6F
General register B0L
GRB0L
R/W
H'FF
H'FFF70
Timer control register 1
16TCR1
R/W
H'80
H'FFF71
Timer I/O control register 1
TIOR1
R/W
H'88
H'FFF72
Timer counter 1H
16TCNT1H R/W
H'00
H'FFF73
Timer counter 1L
16TCNT1L R/W
H'00
H'FFF74
General register A1H
GRA1H
R/W
H'FF
H'FFF75
General register A1L
GRA1L
R/W
H'FF
H'FFF76
General register B1H
GRB1H
R/W
H'FF
H'FFF77
General register B1L
GRB1L
R/W
H'FF
Rev. 3.00 Sep 14, 2005 page 327 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Channel
Address*1
Name
Abbreviation
R/W
Initial
Value
2
H'FFF78
Timer control register 2
16TCR2
R/W
H'80
H'FFF79
Timer I/O control register 2
TIOR2
R/W
H'88
H'FFF7A
Timer counter 2H
16TCNT2H R/W
H'00
H'FFF7B
Timer counter 2L
16TCNT2L R/W
H'00
H'FFF7C
General register A2H
GRA2H
R/W
H'FF
H'FFF7D
General register A2L
GRA2L
R/W
H'FF
H'FFF7E
General register B2H
GRB2H
R/W
H'FF
H'FFF7F
General register B2L
GRB2L
R/W
H'FF
Notes: 1. The lower 20 bits of the address in advanced mode are indicated.
2. Only 0 can be written in bits 3 to 0, to clear the flags.
9.2
Register Descriptions
9.2.1
Timer Start Register (TSTR)
TSTR is an 8-bit readable/writable register that starts and stops the timer counter (16TCNT) in
channels 0 to 2.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
STR2
STR1
STR0
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Reserved bits
Counter start 2 to 0
These bits start and
stop 16TCNT2 to 16TCNT0
TSTR is initialized to H'F8 by a reset and in standby mode.
Bits 7 to 3—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 328 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bit 2—Counter Start 2 (STR2): Starts and stops timer counter 2 (16TCNT2).
Bit 2
STR2
Description
0
16TCNT2 is halted
1
16TCNT2 is counting
(Initial value)
Bit 1—Counter Start 1 (STR1): Starts and stops timer counter 1 (16TCNT1).
Bit 1
STR1
Description
0
16TCNT1 is halted
1
16TCNT1 is counting
(Initial value)
Bit 0—Counter Start 0 (STR0): Starts and stops timer counter 0 (16TCNT0).
Bit 0
STR0
Description
0
16TCNT0 is halted
1
16TCNT0 is counting
9.2.2
(Initial value)
Timer Synchro Register (TSNC)
TSNC is an 8-bit readable/writable register that selects whether channels 0 to 2 operate
independently or synchronously. Channels are synchronized by setting the corresponding bits to
1.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
SYNC2
SYNC1
SYNC0
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Reserved bits
Timer sync 2 to 0
These bits synchronize
channels 2 to 0
TSNC is initialized to H'F8 by a reset and in standby mode.
Bits 7 to 3—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 329 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bit 2—Timer Sync 2 (SYNC2): Selects whether channel 2 operates independently or
synchronously.
Bit 2
SYNC2
Description
0
Channel 2’s timer counter (16TCNT2) operates independently
16TCNT2 is preset and cleared independently of other channels
1
Channel 2 operates synchronously
16TCNT2 can be synchronously preset and cleared
(Initial value)
Bit 1—Timer Sync 1 (SYNC1): Selects whether channel 1 operates independently or
synchronously.
Bit 1
SYNC1
Description
0
Channel 1’s timer counter (16TCNT1) operates independently
16TCNT1 is preset and cleared independently of other channels
1
Channel 1 operates synchronously
16TCNT1 can be synchronously preset and cleared
(Initial value)
Bit 0—Timer Sync 0 (SYNC0): Selects whether channel 0 operates independently or
synchronously.
Bit 0
SYNC0
Description
0
Channel 0’s timer counter (16TCNT0) operates independently
16TCNT0 is preset and cleared independently of other channels
1
Channel 0 operates synchronously
16TCNT0 can be synchronously preset and cleared
Rev. 3.00 Sep 14, 2005 page 330 of 910
REJ09B0258-0300
(Initial value)
Section 9 16-Bit Timer
9.2.3
Timer Mode Register (TMDR)
TMDR is an 8-bit readable/writable register that selects PWM mode for channels 0 to 2. It also
selects phase counting mode and the overflow flag (OVF) setting conditions for channel 2.
Bit
7
6
5
4
3
2
1
0
—
MDF
FDIR
—
—
PWM2
PWM1
PWM0
Initial value
1
0
0
1
1
0
0
0
Read/Write
—
R/W
R/W
—
—
R/W
R/W
R/W
Reserved bit
PWM mode 2 to 0
These bits select PWM
mode for channels 2 to 0
Flag direction
Selects the setting condition for the overflow
flag (OVF) in TISRC
Phase counting mode flag
Selects phase counting mode for channel 2
Reserved bit
TMDR is initialized to H'98 by a reset and in standby mode.
Bit 7—Reserved: This bit cannot be modified and is always read as 1.
Bit 6—Phase Counting Mode Flag (MDF): Selects whether channel 2 operates normally or in
phase counting mode.
Bit 6
MDF
Description
0
Channel 2 operates normally
1
Channel 2 operates in phase counting mode
(Initial value)
When MDF is set to 1 to select phase counting mode, 16TCNT2 operates as an up/down-counter
and pins TCLKA and TCLKB become counter clock input pins. 16TCNT2 counts both rising and
falling edges of TCLKA and TCLKB, and counts up or down as follows.
Rev. 3.00 Sep 14, 2005 page 331 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Counting
Direction
Down-Counting
TCLKA pin
↑
High
↓
Low
Low
↑
High
↓
TCLKB pin
Low
↑
High
↓
↑
High
↓
Low
Up-Counting
In phase counting mode, external clock edge selection by bits CKEG1 and CKEG0 in 16TCR2
and counter clock selection by bits TPSC2 to TPSC0 are invalid, and the above phase counting
mode operations take precedence.
The counter clearing condition selected by the CCLR1 and CCLR0 bits in 16TCR2 and the
compare match/input capture settings and interrupt functions of TIOR2, TISRA, TISRB, TISRC
remain effective in phase counting mode.
Bit 5—Flag Direction (FDIR): Designates the setting condition for the OVF flag in TISRC. The
FDIR designation is valid in all modes in channel 2.
Bit 5
FDIR
Description
0
OVF is set to 1 in TISRC when 16TCNT2 overflows or underflows
1
OVF is set to 1 in TISRC when 16TCNT2 overflows
(Initial value)
Bits 4 and 3—Reserved: These bits cannot be modified and are always read as 1.
Bit 2—PWM Mode 2 (PWM2): Selects whether channel 2 operates normally or in PWM mode.
Bit 2
PWM2
Description
0
Channel 2 operates normally
1
Channel 2 operates in PWM mode
(Initial value)
When bit PWM2 is set to 1 to select PWM mode, pin TIOCA2 becomes a PWM output pin. The
output goes to 1 at compare match with GRA2, and to 0 at compare match with GRB2.
Bit 1—PWM Mode 1 (PWM1): Selects whether channel 1 operates normally or in PWM mode.
Bit 1
PWM1
Description
0
Channel 1 operates normally
1
Channel 1 operates in PWM mode
Rev. 3.00 Sep 14, 2005 page 332 of 910
REJ09B0258-0300
(Initial value)
Section 9 16-Bit Timer
When bit PWM1 is set to 1 to select PWM mode, pin TIOCA1 becomes a PWM output pin. The
output goes to 1 at compare match with GRA1, and to 0 at compare match with GRB1.
Bit 0—PWM Mode 0 (PWM0): Selects whether channel 0 operates normally or in PWM mode.
Bit 0
PWM0
Description
0
Channel 0 operates normally
1
Channel 0 operates in PWM mode
(Initial value)
When bit PWM0 is set to 1 to select PWM mode, pin TIOCA0 becomes a PWM output pin. The
output goes to 1 at compare match with GRA0, and to 0 at compare match with GRB0.
9.2.4
Timer Interrupt Status Register A (TISRA)
TISRA is an 8-bit readable/writable register that indicates GRA compare match or input capture
and enables or disables GRA compare match and input capture interrupt requests.
Bit
7
—
3
2
1
0
IMIEA2 IMIEA1 IMIEA0
—
IMFA2
IMFA1
IMFA0
6
5
4
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/(W)*
R/(W)*
R/(W)*
Input capture/compare match
flags A2 to A0
Status flags indicating GRA
compare match or input capture
Reserved bit
Input capture/compare match interrupt enable A2 to A0
These bits enable or disable interrupts by the IMFA flags
Reserved bit
Note: * Only 0 can be written, to clear the flag.
TISRA is initialized to H'88 by a reset and in standby mode.
Bit 7—Reserved: This bit cannot be modified and is always read as 1.
Rev. 3.00 Sep 14, 2005 page 333 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bit 6—Input Capture/Compare Match Interrupt Enable A2 (IMIEA2): Enables or disables
the interrupt requested by the IMFA2 when IMFA2 flag is set to 1.
Bit 6
IMIEA2
Description
0
IMIA2 interrupt requested by IMFA2 flag is disabled
1
IMIA2 interrupt requested by IMFA2 flag is enabled
(Initial value)
Bit 5—Input Capture/Compare Match Interrupt Enable A1 (IMIEA1): Enables or disables
the interrupt requested by the IMFA1 flag when IMFA1 is set to 1.
Bit 5
IMIEA1
Description
0
IMIA1 interrupt requested by IMFA1 flag is disabled
1
IMIA1 interrupt requested by IMFA1 flag is enabled
(Initial value)
Bit 4—Input Capture/Compare Match Interrupt Enable A0 (IMIEA0): Enables or disables
the interrupt requested by the IMFA0 flag when IMFA0 is set to 1.
Bit 4
IMIEA0
Description
0
IMIA0 interrupt requested by IMFA0 flag is disabled
1
IMIA0 interrupt requested by IMFA0 flag is enabled
(Initial value)
Bit 3—Reserved: This bit cannot be modified and is always read as 1.
Bit 2—Input Capture/Compare Match Flag A2 (IMFA2): This status flag indicates GRA2
compare match or input capture events.
Bit 2
IMFA2
Description
0
[Clearing condition]
(Initial value)
Read IMFA2 flag when IMFA2 =1, then write 0 in IMFA2 flag
1
[Setting conditions]
•
16TCNT2 = GRA2 when GRA2 functions as an output compare register
•
16TCNT2 value is transferred to GRA2 by an input capture signal when GRA2
functions as an input capture register
Rev. 3.00 Sep 14, 2005 page 334 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bit 1—Input Capture/Compare Match Flag A1 (IMFA1): This status flag indicates GRA1
compare match or input capture events.
Bit 1
IMFA1
Description
0
[Clearing condition]
(Initial value)
Read IMFA1 flag when IMFA1 =1, then write 0 in IMFA1 flag
1
[Setting conditions]
•
16TCNT1 = GRA1 when GRA1 functions as an output compare register
•
16TCNT1 value is transferred to GRA1 by an input capture signal when GRA1
functions as an input capture register
Bit 0—Input Capture/Compare Match Flag A0 (IMFA0): This status flag indicates GRA0
compare match or input capture events.
Bit 0
IMFA0
Description
0
[Clearing condition]
(Initial value)
Read IMFA0 flag when IMFA0 =1, then write 0 in IMFA0 flag
1
[Setting conditions]
•
16TCNT0 = GRA0 when GRA0 functions as an output compare register
•
16TCNT0 value is transferred to GRA0 by an input capture signal when GRA0
functions as an input capture register
Rev. 3.00 Sep 14, 2005 page 335 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.2.5
Timer Interrupt Status Register B (TISRB)
TISRB is an 8-bit readable/writable register that indicates GRB compare match or input capture
and enables or disables GRB compare match and input capture interrupt requests.
Bit
7
—
Initial value
Read/Write
1
—
6
5
4
IMIEB2 IMIEB1 IMIEB0
0
R/W
0
R/W
0
R/W
3
2
1
0
—
IMFB2
IMFB1
IMFB0
1
0
0
0
—
R/(W)*
R/(W)*
R/(W)*
Input capture/compare match
flags B2 to B0
Status flags indicating GRB
compare match or input capture
Reserved bit
Input capture/compare match interrupt enable B2 to B0
These bits enable or disable interrupts by the IMFB flags
Reserved bit
Note: * Only 0 can be written, to clear the flag.
TISRB is initialized to H'88 by a reset and in standby mode.
Bit 7—Reserved: This bit cannot be modified and is always read as 1.
Bit 6—Input Capture/Compare Match Interrupt Enable B2 (IMIEB2): Enables or disables
the interrupt requested by the IMFB2 when IMFB2 flag is set to 1.
Bit 6
IMIEB2
Description
0
IMIB2 interrupt requested by IMFB2 flag is disabled
1
IMIB2 interrupt requested by IMFB2 flag is enabled
Rev. 3.00 Sep 14, 2005 page 336 of 910
REJ09B0258-0300
(Initial value)
Section 9 16-Bit Timer
Bit 5—Input Capture/Compare Match Interrupt Enable B1 (IMIEB1): Enables or disables
the interrupt requested by the IMFB1 when IMFB1 flag is set to 1.
Bit 5
IMIEB1
Description
0
IMIB1 interrupt requested by IMFB1 flag is disabled
1
IMIB1 interrupt requested by IMFB1 flag is enabled
(Initial value)
Bit 4—Input Capture/Compare Match Interrupt Enable B0 (IMIEB0): Enables or disables
the interrupt requested by the IMFB0 when IMFB0 flag is set to 1.
Bit 4
IMIEB0
Description
0
IMIB0 interrupt requested by IMFB0 flag is disabled
1
IMIB0 interrupt requested by IMFB0 flag is enabled
(Initial value)
Bit 3—Reserved: This bit cannot be modified and is always read as 1.
Bit 2—Input Capture/Compare Match Flag B2 (IMFB2): This status flag indicates GRB2
compare match or input capture events.
Bit 2
IMFB2
Description
0
[Clearing condition]
(Initial value)
Read IMFB2 flag when IMFB2 =1, then write 0 in IMFB2 flag
1
[Setting conditions]
•
16TCNT2 = GRB2 when GRB2 functions as an output compare register
•
16TCNT2 value is transferred to GRB2 by an input capture signal when GRB2
functions as an input capture register
Rev. 3.00 Sep 14, 2005 page 337 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bit 1—Input Capture/Compare Match Flag B1 (IMFB1): This status flag indicates GRB1
compare match or input capture events.
Bit 1
IMFB1
Description
0
[Clearing condition]
(Initial value)
Read IMFB1 flag when IMFB1 =1, then write 0 in IMFB1 flag
1
[Setting conditions]
•
16TCNT1 = GRB1 when GRB1 functions as an output compare register
•
16TCNT1 value is transferred to GRB1 by an input capture signal when GRB1
functions as an input capture register
Bit 0—Input Capture/Compare Match Flag B0 (IMFB0): This status flag indicates GRB0
compare match or input capture events.
Bit 0
IMFB0
Description
0
[Clearing condition]
(Initial value)
Read IMFB0 flag when IMFB0 =1, then write 0 in IMFB0 flag
1
[Setting conditions]
•
16TCNT0 = GRB0 when GRB0 functions as an output compare register
•
16TCNT0 value is transferred to GRB0 by an input capture signal when GRB0
functions as an input capture register
Rev. 3.00 Sep 14, 2005 page 338 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.2.6
Timer Interrupt Status Register C (TISRC)
TISRC is an 8-bit readable/writable register that indicates 16TCNT overflow or underflow and
enables or disables overflow interrupt requests.
Bit
7
6
5
4
3
2
1
0
—
OVIE2
OVIE1
OVIE0
—
OVF2
OVF1
OVF0
0
0
Initial value
1
0
0
0
1
Read/Write
—
R/W
R/W
R/W
—
R/(W)* R/(W)*
0
R/(W)*
Overflow flags 2 to 0
Status flags indicating
interrupts by OVF flags
Reserved bit
Overflow interrupt enable 2 to 0
These bits enable or disable interrupts by the OVF flags
Reserved bit
Note: * Only 0 can be written, to clear the flag.
TISRC is initialized to H'88 by a reset and in standby mode.
Bit 7—Reserved: This bit cannot be modified and is always read as 1.
Bit 6—Overflow Interrupt Enable 2 (OVIE2): Enables or disables the interrupt requested by
the OVF2 when OVF2 flag is set to 1.
Bit 6
OVIE2
Description
0
OVI2 interrupt requested by OVF2 flag is disabled
1
OVI2 interrupt requested by OVF2 flag is enabled
(Initial value)
Bit 5—Overflow Interrupt Enable 1 (OVIE1): Enables or disables the interrupt requested by
the OVF1 when OVF1 flag is set to 1.
Bit 5
OVIE1
Description
0
OVI1 interrupt requested by OVF1 flag is disabled
1
OVI1 interrupt requested by OVF1 flag is enabled
(Initial value)
Rev. 3.00 Sep 14, 2005 page 339 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bit 4—Overflow Interrupt Enable 0 (OVIE0): Enables or disables the interrupt requested by
the OVF0 when OVF0 flag is set to 1.
Bit 4
OVIE0
Description
0
OVI0 interrupt requested by OVF0 flag is disabled
1
OVI0 interrupt requested by OVF0 flag is enabled
(Initial value)
Bit 3—Reserved: This bit cannot be modified and is always read as 1.
Bit 2—Overflow Flag 2 (OVF2): This status flag indicates 16TCNT2 overflow.
Bit 2
OVF2
Description
0
[Clearing condition]
(Initial value)
Read OVF2 flag when OVF2 =1, then write 0 in OVF2 flag
1
[Setting condition]
16TCNT2 overflowed from H'FFFF to H'0000, or underflowed from H'0000 to H'FFFF
Note: 16TCNT underflow occurs when 16TCNT operates as an up/down-counter. Underflow
occurs only when channel 2 operates in phase counting mode (MDF = 1 in TMDR).
Bit 1—Overflow Flag 1 (OVF1): This status flag indicates 16TCNT1 overflow.
Bit 1
OVF1
Description
0
[Clearing condition]
(Initial value)
Read OVF1 flag when OVF1 =1, then write 0 in OVF1 flag
1
[Setting condition]
16TCNT1 overflowed from H'FFFF to H'0000
Bit 0—Overflow Flag 0 (OVF0): This status flag indicates 16TCNT0 overflow.
Bit 0
OVF0
Description
0
[Clearing condition]
Read OVF0 flag when OVF0 =1, then write 0 in OVF0 flag
1
[Setting condition]
16TCNT0 overflowed from H'FFFF to H'0000
Rev. 3.00 Sep 14, 2005 page 340 of 910
REJ09B0258-0300
(Initial value)
Section 9 16-Bit Timer
9.2.7
Timer Counters (16TCNT)
16TCNT is a 16-bit counter. The 16-bit timer has three 16TCNTs, one for each channel.
Channel
Abbreviation
Function
0
16TCNT0
Up-counter
1
16TCNT1
2
16TCNT2
Bit
Initial value
Read/Write
Phase counting mode: up/down-counter
Other modes: up-counter
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Each 16TCNT is a 16-bit readable/writable register that counts pulse inputs from a clock source.
The clock source is selected by bits TPSC2 to TPSC0 in 16TCR.
16TCNT0 and 16TCNT1 are up-counters. 16TCNT2 is an up/down-counter in phase counting
mode and an up-counter in other modes.
16TCNT can be cleared to H'0000 by compare match with GRA or GRB or by input capture to
GRA or GRB (counter clearing function).
When 16TCNT overflows (changes from H'FFFF to H'0000), the OVF flag is set to 1 in TISRC of
the corresponding channel.
When 16TCNT underflows (changes from H'0000 to H'FFFF), the OVF flag is set to 1 in TISRC
of the corresponding channel.
The 16TCNTs are linked to the CPU by an internal 16-bit bus and can be written or read by either
word access or byte access.
Each 16TCNT is initialized to H'0000 by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 341 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.2.8
General Registers (GRA, GRB)
The general registers are 16-bit registers. The 16-bit timer has 6 general registers, two in each
channel.
Channel
Abbreviation
Function
0
GRA0, GRB0
Output compare/input capture register
1
GRA1, GRB1
2
GRA2, GRB2
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
A general register is a 16-bit readable/writable register that can function as either an output
compare register or an input capture register. The function is selected by settings in TIOR.
When a general register is used as an output compare register, its value is constantly compared
with the 16TCNT value. When the two values match (compare match), the IMFA or IMFB flag is
set to 1 in TISRA/TISRB. Compare match output can be selected in TIOR.
When a general register is used as an input capture register, an external input capture signal are
detected and the current 16TCNT value is stored in the general register. The corresponding IMFA
or IMFB flag in TISRA/TISRB is set to 1 at the same time. The edges of the input capture signal
are selected in TIOR.
TIOR settings are ignored in PWM mode.
General registers are linked to the CPU by an internal 16-bit bus and can be written or read by
either word access or byte access.
General registers are set as output compare registers (with no pin output) and initialized to
H'FFFF by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 342 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.2.9
Timer Control Registers (16TCR)
16TCR is an 8-bit register. The 16-bit timer has three 16TCRs, one in each channel.
Channel
Abbreviation
Function
0
16TCR0
1
16TCR1
2
16TCR2
16TCR controls the timer counter. The 16TCRs in all
channels are functionally identical. When phase counting
mode is selected in channel 2, the settings of bits CKEG1
and CKEG0 and TPSC2 to TPSC0 in 16TCR2 are ignored.
Bit
7
6
5
—
CCLR1
CCLR0
4
3
CKEG1 CKEG0
2
1
0
TPSC2
TPSC1
TPSC0
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Timer prescaler 2 to 0
These bits select the timer
counter clock
Clock edge 1/0
These bits select external clock edges
Counter clear 1/0
These bits select the counter clear source
Reserved bit
Each 16TCR is an 8-bit readable/writable register that selects the timer counter clock source,
selects the edge or edges of external clock sources, and selects how the counter is cleared.
16TCR is initialized to H'80 by a reset and in standby mode.
Bit 7—Reserved: This bit cannot be modified and is always read as 1.
Rev. 3.00 Sep 14, 2005 page 343 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bits 6 and 5—Counter Clear 1 and 0 (CCLR1, CCLR0): These bits select how 16TCNT is
cleared.
Bit 6
CCLR1
Bit 5
CCLR0
Description
0
0
16TCNT is not cleared
1
(Initial value)
1
1
16TCNT is cleared by GRA compare match or input capture*
0
16TCNT is cleared by GRB compare match or input capture*1
1
Synchronous clear: 16TCNT is cleared in synchronization with other
2
synchronized timers*
Notes: 1. 16TCNT is cleared by compare match when the general register functions as an output
compare register, and by input capture when the general register functions as an input
capture register.
2. Selected in TSNC.
Bits 4 and 3—Clock Edge 1 and 0 (CKEG1, CKEG0): These bits select external clock input
edges when an external clock source is used.
Bit 4
CKEG1
Bit 3
CKEG0
Description
0
0
Count rising edges
1
Count falling edges
—
Count both edges
1
(Initial value)
When channel 2 is set to phase counting mode, bits CKEG1 and CKEG0 in 16TCR2 are ignored.
Phase counting takes precedence.
Rev. 3.00 Sep 14, 2005 page 344 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bits 2 to 0—Timer Prescaler 2 to 0 (TPSC2 to TPSC0): These bits select the counter clock
source.
Bit 2
TPSC2
Bit 1
TPSC1
Bit 0
TPSC0
Function
0
0
0
Internal clock: φ
1
Internal clock: φ/2
0
Internal clock: φ/4
1
Internal clock: φ/8
0
External clock A: TCLKA input
1
External clock B: TCLKB input
0
External clock C: TCLKC input
1
External clock D: TCLKD input
1
1
0
1
(Initial value)
When bit TPSC2 is cleared to 0 an internal clock source is selected, and the timer counts only
falling edges. When bit TPSC2 is set to 1 an external clock source is selected, and the timer
counts the edges selected by bits CKEG1 and CKEG0.
When channel 2 is set to phase counting mode (MDF = 1 in TMDR), the settings of bits TPSC2
to TPSC0 in 16TCR2 are ignored. Phase counting takes precedence.
Rev. 3.00 Sep 14, 2005 page 345 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.2.10
Timer I/O Control Register (TIOR)
TIOR is an 8-bit register. The 16-bit timer has three TIORs, one in each channel.
Channel
Abbreviation Function
0
TIOR0
1
TIOR1
2
TIOR2
Bit
TIOR controls the general registers. Some functions differ in PWM
mode.
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
I/O control A2 to A0
These bits select GRA
functions
Reserved bit
I/O control B2 to B0
These bits select GRB functions
Reserved bit
Each TIOR is an 8-bit readable/writable register that selects the output compare or input capture
function for GRA and GRB, and specifies the functions of the TIORA and TIORB pins. If the
output compare function is selected, TIOR also selects the type of output. If input capture is
selected, TIOR also selects the edges of the input capture signal.
TIOR is initialized to H'88 by a reset and in standby mode.
Bit 7—Reserved: This bit cannot be modified and is always read as 1.
Rev. 3.00 Sep 14, 2005 page 346 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Bits 6 to 4—I/O Control B2 to B0 (IOB2 to IOB0): These bits select the GRB function.
Bit 6
IOB2
Bit 5
IOB1
Bit 4
IOB0
0
0
0
1
1
1
0
GRB is an output
compare register
No output at compare match
(Initial value)
0 output at GRB compare match*1
0
1 output at GRB compare match*1
1
Output toggles at GRB compare match
(1 output in channel 2)*1 *2
0
1
1
Function
GRB is an input
compare register
0
GRB captures rising edge of input
GRB captures falling edge of input
GRB captures both edges of input
1
Notes: 1. After a reset, the output conforms to the TOLR setting until the first compare match.
2. Channel 2 output cannot be toggled by compare match. When this setting is made, 1
output is selected automatically.
Bit 3—Reserved: This bit cannot be modified and is always read as 1.
Bits 2 to 0—I/O Control A2 to A0 (IOA2 to IOA0): These bits select the GRA function.
Bit 2
IOA2
Bit 1
IOA1
Bit 0
IOA0
0
0
0
1
1
1
0
GRA is an output
compare register
No output at compare match
(Initial value)
0 output at GRA compare match*1
0
1 output at GRA compare match*1
1
Output toggles at GRA compare match
1 2
(1 output in channel 2)* *
0
1
1
Function
0
GRA is an input
compare register
GRA captures rising edge of input
GRA captures falling edge of input
GRA captures both edges of input
1
Notes: 1. After a reset, the output conforms to the TOLR setting until the first compare match.
2. Channel 2 output cannot be toggled by compare match. When this setting is made, 1
output is selected automatically.
Rev. 3.00 Sep 14, 2005 page 347 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.2.11
Timer Output Level Setting Register C (TOLR)
TOLR is an 8-bit write-only register that selects the timer output level for channels 0 to 2.
Bit
7
6
5
4
3
2
1
0
—
—
TOB2
TOA2
TOB1
TOA1
TOB0
TOA0
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
W
W
W
W
W
W
Output level setting A2 to A0, B2 to B0
These bits set the levels of the timer outputs
(TIOCA2 to TIOCA0, and TIOCB2 to TIOCB0)
Reserved bits
A TOLR setting can only be made when the corresponding bit in TSTR is 0.
TOLR is a write-only register, and cannot be read. If it is read, all bits will return a value of 1.
TOLR is initialized to H'C0 by a reset and in standby mode.
Bits 7 and 6—Reserved: These bits cannot be modified.
Bit 5—Output Level Setting B2 (TOB2): Sets the value of timer output TIOCB2.
Bit 5
TOB2
Description
0
TIOCB2 is 0
1
TIOCB2 is 1
(Initial value)
Bit 4—Output Level Setting A2 (TOA2): Sets the value of timer output TIOCA2.
Bit 4
TOA2
Description
0
TIOCA2 is 0
1
TIOCA2 is 1
Rev. 3.00 Sep 14, 2005 page 348 of 910
REJ09B0258-0300
(Initial value)
Section 9 16-Bit Timer
Bit 3—Output Level Setting B1 (TOB1): Sets the value of timer output TIOCB1.
Bit 3
TOB1
Description
0
TIOCB1 is 0
1
TIOCB1 is 1
(Initial value)
Bit 2—Output Level Setting A1 (TOA1): Sets the value of timer output TIOCA1.
Bit 2
TOA1
Description
0
TIOCA1 is 0
1
TIOCA1 is 1
(Initial value)
Bit 1—Output Level Setting B0 (TOB0): Sets the value of timer output TIOCB0.
Bit 0
TOB0
Description
0
TIOCB0 is 0
1
TIOCB0 is 1
(Initial value)
Bit 0—Output Level Setting A0 (TOA0): Sets the value of timer output TIOCA0.
Bit 0
TOA0
Description
0
TIOCA0 is 0
1
TIOCA0 is 1
(Initial value)
Rev. 3.00 Sep 14, 2005 page 349 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.3
CPU Interface
9.3.1
16-Bit Accessible Registers
The timer counters (16TCNTs), general registers A and B (GRAs and GRBs) are 16-bit registers,
and are linked to the CPU by an internal 16-bit data bus. These registers can be written or read a
word at a time, or a byte at a time.
Figures 9.4 and 9.5 show examples of word read/write access to a timer counter (16TCNT).
Figures 9.6 to 9.9 show examples of byte read/write access to 16TCNTH and 16TCNTL.
On-chip data bus
H
CPU
L
H
Bus interface
L
16TCNTH
Module
data bus
16TCNTL
Figure 9.4 16TCNT Access Operation [CPU → 16TCNT (Word)]
On-chip data bus
H
CPU
L
H
Bus interface
L
16TCNTH
16TCNTL
Figure 9.5 Access to Timer Counter (CPU Reads 16TCNT, Word)
Rev. 3.00 Sep 14, 2005 page 350 of 910
REJ09B0258-0300
Module
data bus
Section 9 16-Bit Timer
On-chip data bus
H
CPU
L
H
Bus interface
L
16TCNTH
Module
data bus
16TCNTL
Figure 9.6 Access to Timer Counter H (CPU Writes to 16TCNTH, Upper Byte)
On-chip data bus
H
CPU
L
H
Bus interface
L
16TCNTH
Module
data bus
16TCNTL
Figure 9.7 Access to Timer Counter L (CPU Writes to 16TCNTL, Lower Byte)
On-chip data bus
H
CPU
L
H
Bus interface
L
16TCNTH
Module
data bus
16TCNTL
Figure 9.8 Access to Timer Counter H (CPU Reads 16TCNTH, Upper Byte)
Rev. 3.00 Sep 14, 2005 page 351 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
On-chip data bus
H
CPU
H
L
Bus interface
L
16TCNTH
Module
data bus
16TCNTL
Figure 9.9 Access to Timer Counter L (CPU Reads 16TCNTL, Lower Byte)
9.3.2
8-Bit Accessible Registers
The registers other than the timer counters and general registers are 8-bit registers. These
registers are linked to the CPU by an internal 8-bit data bus.
Figures 9.10 and 9.11 show examples of byte read and write access to a 16TCR.
If a word-size data transfer instruction is executed, two byte transfers are performed.
On-chip data bus
H
CPU
L
H
Bus interface
L
16TCR
Figure 9.10 16TCR Access (CPU Writes to 16TCR)
Rev. 3.00 Sep 14, 2005 page 352 of 910
REJ09B0258-0300
Module
data bus
Section 9 16-Bit Timer
On-chip data bus
H
CPU
H
L
Bus interface
L
Module
data bus
16TCR
Figure 9.11 16TCR Access (CPU Reads 16TCR)
9.4
Operation
9.4.1
Overview
A summary of operations in the various modes is given below.
Normal Operation: Each channel has a timer counter and general registers. The timer counter
counts up, and can operate as a free-running counter, periodic counter, or external event counter.
GRA and GRB can be used for input capture or output compare.
Synchronous Operation: The timer counters in designated channels are preset synchronously.
Data written to the timer counter in any one of these channels is simultaneously written to the
timer counters in the other channels as well. The timer counters can also be cleared
synchronously if so designated by the CCLR1 and CCLR0 bits in the TCRs.
PWM Mode: A PWM waveform is output from the TIOCA pin. The output goes to 1 at compare
match A and to 0 at compare match B. The duty cycle can be varied from 0% to 100% depending
on the settings of GRA and GRB. When a channel is set to PWM mode, its GRA and GRB
automatically become output compare registers.
Phase Counting Mode: The phase relationship between two clock signals input at TCLKA and
TCLKB is detected and 16TCNT2 counts up or down accordingly. When phase counting mode is
selected TCLKA and TCLKB become clock input pins and 16TCNT2 operates as an up/downcounter.
Rev. 3.00 Sep 14, 2005 page 353 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.4.2
Basic Functions
Counter Operation: When one of bits STR0 to STR2 is set to 1 in the timer start register
(TSTR), the timer counter (16TCNT) in the corresponding channel starts counting. The counting
can be free-running or periodic.
• Sample setup procedure for counter
Figure 9.12 shows a sample procedure for setting up a counter.
Counter setup
1
Select counter clock
Count operation
No
Yes
Free-running counting
Periodic counting
Select counter clear source
2
Select output compare
register function
3
Set period
4
Start counter
5
Periodic counter
Start counter
Free-running counter
Figure 9.12 Counter Setup Procedure (Example)
Rev. 3.00 Sep 14, 2005 page 354 of 910
REJ09B0258-0300
5
Section 9 16-Bit Timer
1. Set bits TPSC2 to TPSC0 in 16TCR to select the counter clock source. If an external clock
source is selected, set bits CKEG1 and CKEG0 in 16TCR to select the desired edge(s) of the
external clock signal.
2. For periodic counting, set CCLR1 and CCLR0 in 16TCR to have 16TCNT cleared at GRA
compare match or GRB compare match.
3. Set TIOR to select the output compare function of GRA or GRB, whichever was selected in
step 2.
4. Write the count period in GRA or GRB, whichever was selected in step 2.
5. Set the STR bit to 1 in TSTR to start the timer counter.
• Free-running and periodic counter operation
A reset leaves the counters (16TCNTs) in 16-bit timer channels 0 to 2 all set as free-running
counters. A free-running counter starts counting up when the corresponding bit in TSTR is set
to 1. When the count overflows from H'FFFF to H'0000, the OVF flag is set to 1 in TISRC.
After the overflow, the counter continues counting up from H'0000. Figure 9.13 illustrates
free-running counting.
16TCNT value
H'FFFF
H'0000
Time
STR0 to
STR2 bit
OVF
Figure 9.13 Free-Running Counter Operation
When a channel is set to have its counter cleared by compare match, in that channel 16TCNT
operates as a periodic counter. Select the output compare function of GRA or GRB, set bit
CCLR1 or CCLR0 in 16TCR to have the counter cleared by compare match, and set the count
period in GRA or GRB. After these settings, the counter starts counting up as a periodic
counter when the corresponding bit is set to 1 in TSTR. When the count matches GRA or
GRB, the IMFA or IMFB flag is set to 1 in TISRA/TISRB and the counter is cleared to
H'0000. If the corresponding IMIEA or IMIEB bit is set to 1 in TISRA/TISRB, a CPU
interrupt is requested at this time. After the compare match, 16TCNT continues counting up
from H'0000. Figure 9.14 illustrates periodic counting.
Rev. 3.00 Sep 14, 2005 page 355 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
16TCNT value
Counter cleared by general
register compare match
GR
Time
H'0000
STR bit
IMF
Figure 9.14 Periodic Counter Operation
• 16TCNT count timing
 Internal clock source
Bits TPSC2 to TPSC0 in 16TCR select the system clock (φ) or one of three internal clock
sources obtained by prescaling the system clock (φ/2, φ/4, φ/8).
Figure 9.15 shows the timing.
φ
Internal
clock
16TCNT input
clock
16TCNT
N–1
N
N+1
Figure 9.15 Count Timing for Internal Clock Sources
 External clock source
The external clock pin (TCLKA to TCLKD) can be selected by bits TPSC2 to TPSC0 in
16TCR, and the detected edge by bits CKEG1 and CKEG0. The rising edge, falling edge,
or both edges can be selected.
The pulse width of the external clock signal must be at least 1.5 system clocks when a
single edge is selected, and at least 2.5 system clocks when both edges are selected.
Shorter pulses will not be counted correctly.
Figure 9.16 shows the timing when both edges are detected.
Rev. 3.00 Sep 14, 2005 page 356 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
φ
External
clock input
16TCNT input
clock
16TCNT
N–1
N
N+1
Figure 9.16 Count Timing for External Clock Sources (when Both Edges are Detected)
Waveform Output by Compare Match: In 16-bit timer channels 0, 1 compare match A or B
can cause the output at the TIOCA or TIOCB pin to go to 0, go to 1, or toggle. In channel 2 the
output can only go to 0 or go to 1.
• Sample setup procedure for waveform output by compare match
Figure 9.17 shows an example of the setup procedure for waveform output by compare match.
Output setup
1. Select the compare match output mode (0, 1, or
toggle) in TIOR. When a waveform output mode
is selected, the pin switches from its generic input/
output function to the output compare function
(TIOCA or TIOCB). An output compare pin outputs
the value set in TOLR until the first compare match
occurs.
Select waveform
output mode
1
Set output timing
2
2. Set a value in GRA or GRB to designate the
compare match timing.
Start counter
3
3. Set the STR bit to 1 in TSTR to start the timer
counter.
Waveform output
Figure 9.17 Setup Procedure for Waveform Output by Compare Match (Example)
Rev. 3.00 Sep 14, 2005 page 357 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
• Examples of waveform output
Figure 9.18 shows examples of 0 and 1 output. 16TCNT operates as a free-running counter, 0
output is selected for compare match A, and 1 output is selected for compare match B. When
the pin is already at the selected output level, the pin level does not change.
16TCNT value
H'FFFF
GRB
GRA
H'0000
Time
TIOCB
No change
No change
TIOCA
No change
No change
1 output
0 output
Figure 9.18 0 and 1 Output (TOA = 1, TOB = 0)
Figure 9.19 shows examples of toggle output. 16TCNT operates as a periodic counter, cleared
by compare match B. Toggle output is selected for both compare match A and B.
16TCNT value
Counter cleared by compare match with GRB
GRB
GRA
H'0000
Time
TIOCB
Toggle
output
TIOCA
Toggle
output
Figure 9.19 Toggle Output (TOA = 1, TOB = 0)
Rev. 3.00 Sep 14, 2005 page 358 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
• Output compare output timing
The compare match signal is generated in the last state in which 16TCNT and the general
register match (when 16TCNT changes from the matching value to the next value). When the
compare match signal is generated, the output value selected in TIOR is output at the output
compare pin (TIOCA or TIOCB). When 16TCNT matches a general register, the compare
match signal is not generated until the next counter clock pulse.
Figure 9.20 shows the output compare timing.
φ
16TCNT input
clock
16TCNT
N
GR
N
N+1
Compare
match signal
TIOCA,
TIOCB
Figure 9.20 Output Compare Output Timing
Input Capture Function: The 16TCNT value can be transferred to a general register when an
input edge is detected at an input capture input/output compare pin (TIOCA or TIOCB). Risingedge, falling-edge, or both-edge detection can be selected. The input capture function can be used
to measure pulse width or period.
Rev. 3.00 Sep 14, 2005 page 359 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
• Sample setup procedure for input capture
Figure 9.21 shows a sample procedure for setting up input capture.
Input selection
1. Set TIOR to select the input capture function of a
general register and the rising edge, falling edge,
or both edges of the input capture signal. Clear the
DDR bit to 0 before making these TIOR settings.
Select input-capture input
1
Start counter
2
2. Set the STR bit to 1 in TSTR to start the timer
counter.
Input capture
Figure 9.21 Setup Procedure for Input Capture (Example)
• Examples of input capture
Figure 9.22 illustrates input capture when the falling edge of TIOCB and both edges of
TIOCA are selected as capture edges. 16TCNT is cleared by input capture into GRB.
16TCNT value
H'0180
H'0160
H'0005
H'0000
TIOCB
TIOCA
GRA
H'0005
H'0160
GRB
H'0180
Figure 9.22 Input Capture (Example)
Rev. 3.00 Sep 14, 2005 page 360 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
• Input capture signal timing
Input capture on the rising edge, falling edge, or both edges can be selected by settings in
TIOR. Figure 9.23 shows the timing when the rising edge is selected. The pulse width of the
input capture signal must be at least 1.5 system clocks for single-edge capture, and 2.5 system
clocks for capture of both edges.
φ
Input-capture input
Input capture signal
N
16TCNT
N
GRA, GRB
Figure 9.23 Input Capture Signal Timing
9.4.3
Synchronization
The synchronization function enables two or more timer counters to be synchronized by writing
the same data to them simultaneously (synchronous preset). With appropriate 16TCR settings,
two or more timer counters can also be cleared simultaneously (synchronous clear).
Synchronization enables additional general registers to be associated with a single time base.
Synchronization can be selected for all channels (0 to 2).
Sample Setup Procedure for Synchronization: Figure 9.24 shows a sample procedure for
setting up synchronization.
Rev. 3.00 Sep 14, 2005 page 361 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Setup for synchronization
Select synchronization
1
Synchronous preset
Write to 16TCNT
Synchronous clear
2
Clearing
synchronized to this
channel?
No
Yes
Synchronous preset
Select counter clear source
3
Select counter clear source
4
Start counter
5
Start counter
5
Counter clear
Synchronous clear
1. Set the SYNC bits to 1 in TSNC for the channels to be synchronized.
2. When a value is written in 16TCNT in one of the synchronized channels, the same value is
simultaneously written in 16TCNT in the other channels.
3. Set the CCLR1 or CCLR0 bit in 16TCR to have the counter cleared by compare match or input capture.
4. Set the CCLR1 and CCLR0 bits in 16TCR to have the counter cleared synchronously.
5. Set the STR bits in TSTR to 1 to start the synchronized counters.
Figure 9.24 Setup Procedure for Synchronization (Example)
Example of Synchronization: Figure 9.25 shows an example of synchronization. Channels 0, 1,
and 2 are synchronized, and are set to operate in PWM mode. Channel 0 is set for counter
clearing by compare match with GRB0. Channels 1 and 2 are set for synchronous counter
clearing. The timer counters in channels 0, 1, and 2 are synchronously preset, and are
synchronously cleared by compare match with GRB0. A three-phase PWM waveform is output
from pins TIOCA0, TIOCA1, and TIOCA2. For further information on PWM mode, see section
9.4.4, PWM Mode.
Rev. 3.00 Sep 14, 2005 page 362 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Value of 16TCNT0
to 16TCNT2
Cleared by compare match with GRB0
GRB0
GRB1
GRA0
GRB2
GRA1
GRA2
H'0000
TIOCA0
TIOCA1
TIOCA2
Figure 9.25 Synchronization (Example)
9.4.4
PWM Mode
In PWM mode GRA and GRB are paired and a PWM waveform is output from the TIOCA pin.
GRA specifies the time at which the PWM output changes to 1. GRB specifies the time at which
the PWM output changes to 0. If either GRA or GRB compare match is selected as the counter
clear source, a PWM waveform with a duty cycle from 0% to 100% is output at the TIOCA pin.
PWM mode can be selected in all channels (0 to 2).
Table 9.4 summarizes the PWM output pins and corresponding registers. If the same value is set
in GRA and GRB, the output does not change when compare match occurs.
Rev. 3.00 Sep 14, 2005 page 363 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Table 9.4
PWM Output Pins and Registers
Channel
Output Pin
1 Output
0 Output
0
TIOCA0
GRA0
GRB0
1
TIOCA1
GRA1
GRB1
2
TIOCA2
GRA2
GRB2
Sample Setup Procedure for PWM Mode: Figure 9.26 shows a sample procedure for setting up
PWM mode.
PWM mode
Select counter clock
1
Select counter clear source
2
1. Set bits TPSC2 to TPSC0 in 16TCR to
select the counter clock source. If an
external clock source is selected, set
bits CKEG1 and CKEG0 in 16TCR to
select the desired edge(s) of the
external clock signal.
2. Set bits CCLR1 and CCLR0 in 16TCR
to select the counter clear source.
3. Set the time at which the PWM
waveform should go to 1 in GRA.
Set GRA
3
Set GRB
4
Select PWM mode
5
Start counter
6
PWM mode
4. Set the time at which the PWM
waveform should go to 0 in GRB.
5. Set the PWM bit in TMDR to select
PWM mode. When PWM mode is
selected, regardless of the TIOR
contents, GRA and GRB become
output compare registers specifying
the times at which the PWM output
goes to 1 and 0. The TIOCA pin
automatically becomes the PWM
output pin. The TIOCB pin conforms
to the settings of bits IOB1 and IOB0
in TIOR. If TIOCB output is not
desired, clear both IOB1 and IOB0 to 0.
6. Set the STR bit to 1 in TSTR to start
the timer counter.
Figure 9.26 Setup Procedure for PWM Mode (Example)
Rev. 3.00 Sep 14, 2005 page 364 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Examples of PWM Mode: Figure 9.27 shows examples of operation in PWM mode. In PWM
mode TIOCA becomes an output pin. The output goes to 1 at compare match with GRA, and to 0
at compare match with GRB.
In the examples shown, 16TCNT is cleared by compare match with GRA or GRB. Synchronized
operation and free-running counting are also possible.
16TCNT value
Counter cleared by compare match A
GRA
GRB
Time
H'0000
TIOCA
a. Counter cleared by GRA (TOA = 1)
16TCNT value
Counter cleared by compare match B
GRB
GRA
Time
H'0000
TIOCA
b. Counter cleared by GRB (TOA = 0)
Figure 9.27 PWM Mode (Example 1)
Rev. 3.00 Sep 14, 2005 page 365 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Figure 9.28 shows examples of the output of PWM waveforms with duty cycles of 0% and 100%.
If the counter is cleared by compare match with GRB, and GRA is set to a higher value than
GRB, the duty cycle is 0%. If the counter is cleared by compare match with GRA, and GRB is set
to a higher value than GRA, the duty cycle is 100%.
16TCNT value
Counter cleared by compare match B
GRB
GRA
Time
H'0000
TIOCA
Write to GRA
Write to GRA
a. 0% duty cycle (TOA=0)
16TCNT value
Counter cleared by compare match A
GRA
GRB
Time
H'0000
TIOCA
Write to GRB
Write to GRB
b. 100% duty cycle (TOA=1)
Figure 9.28 PWM Mode (Example 2)
Rev. 3.00 Sep 14, 2005 page 366 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.4.5
Phase Counting Mode
In phase counting mode the phase difference between two external clock inputs (at the TCLKA
and TCLKB pins) is detected, and 16TCNT2 counts up or down accordingly.
In phase counting mode, the TCLKA and TCLKB pins automatically function as external clock
input pins and 16TCNT2 becomes an up/down-counter, regardless of the settings of bits TPSC2
to TPSC0, CKEG1, and CKEG0 in 16TCR2. Settings of bits CCLR1, CCLR0 in 16TCR2, and
settings in TIOR2, TISRA, TISRB, TISRC, setting of STR2 bit in TSTR, GRA2, and GRB2 are
valid. The input capture and output compare functions can be used, and interrupts can be
generated.
Phase counting is available only in channel 2.
Sample Setup Procedure for Phase Counting Mode: Figure 9.29 shows a sample procedure for
setting up phase counting mode.
Phase counting mode
Select phase counting mode
1
1. Set the MDF bit in TMDR to 1 to select
phase counting mode.
2. Select the flag setting condition with
the FDIR bit in TMDR.
Select flag setting condition
2
Start counter
3
3. Set the STR2 bit to 1 in TSTR to start
the timer counter.
Phase counting mode
Figure 9.29 Setup Procedure for Phase Counting Mode (Example)
Rev. 3.00 Sep 14, 2005 page 367 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Example of Phase Counting Mode: Figure 9.30 shows an example of operations in phase
counting mode. Table 9.5 lists the up-counting and down-counting conditions for 16TCNT2.
In phase counting mode both the rising and falling edges of TCLKA and TCLKB are counted.
The phase difference between TCLKA and TCLKB must be at least 1.5 states, the phase overlap
must also be at least 1.5 states, and the pulse width must be at least 2.5 states.
16TCNT2 value
Counting up
Counting down
TCLKB
TCLKA
Figure 9.30 Operation in Phase Counting Mode (Example)
Table 9.5
Up/Down Counting Conditions
Counting
Direction
Up-Counting
TCLKB pin
↑
High
↓
Low
HIgh
↓
Low
↑
TCLKA pin
Low
↑
High
↓
↓
Low
↑
HIgh
Phase
difference
Down-Counting
Phase
difference
Pulse width
Pulse width
TCLKA
TCLKB
Overlap
Overlap
Phase difference and overlap: at least 1.5 states
at least 2.5 states
Pulse width:
Figure 9.31 Phase Difference, Overlap, and Pulse Width in Phase Counting Mode
Rev. 3.00 Sep 14, 2005 page 368 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.4.6
16-Bit Timer Output Timing
The initial value of 16-bit timer output when a timer count operation begins can be specified
arbitrarily by making a setting in TOLR.
Figure 9.32 shows the timing for setting the initial value with TOLR.
Only write to TOLR when the corresponding bit in TSTR is cleared to 0.
T1
T3
T2
φ
Address bus
TOLR
16-bit timer output pin
TOLR address
N
N
Figure 9.32 Timing for Setting 16-Bit Timer Output Level by Writing to TOLR
Rev. 3.00 Sep 14, 2005 page 369 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.5
Interrupts
The 16-bit timer has two types of interrupts: input capture/compare match interrupts, and
overflow interrupts.
9.5.1
Setting of Status Flags
Timing of Setting of IMFA and IMFB at Compare Match: IMFA and IMFB are set to 1 by a
compare match signal generated when 16TCNT matches a general register (GR). The compare
match signal is generated in the last state in which the values match (when 16TCNT is updated
from the matching count to the next count). Therefore, when 16TCNT matches a general register,
the compare match signal is not generated until the next 16TCNT clock input. Figure 9.33 shows
the timing of the setting of IMFA and IMFB.
φ
16TCNT input
clock
16TCNT
N
GR
N+1
N
Compare
match signal
IMF
IMI
Figure 9.33 Timing of Setting of IMFA and IMFB by Compare Match
Rev. 3.00 Sep 14, 2005 page 370 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Timing of Setting of IMFA and IMFB by Input Capture: IMFA and IMFB are set to 1 by an
input capture signal. The 16TCNT contents are simultaneously transferred to the corresponding
general register. Figure 9.34 shows the timing.
φ
Input capture
signal
IMF
16TCNT
GR
N
N
IMI
Figure 9.34 Timing of Setting of IMFA and IMFB by Input Capture
Rev. 3.00 Sep 14, 2005 page 371 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Timing of Setting of Overflow Flag (OVF): OVF is set to 1 when 16TCNT overflows from
H'FFFF to H'0000 or underflows from H'0000 to H'FFFF. Figure 9.35 shows the timing.
φ
16TCNT
Overflow
signal
OVF
OVI
Figure 9.35 Timing of Setting of OVF
9.5.2
Timing of Clearing of Status Flags
If the CPU reads a status flag while it is set to 1, then writes 0 in the status flag, the status flag is
cleared. Figure 9.36 shows the timing.
TISR write cycle
T1
T2
T3
φ
Address
TISR address
IMF, OVF
Figure 9.36 Timing of Clearing of Status Flags
Rev. 3.00 Sep 14, 2005 page 372 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.5.3
Interrupt Sources
Each 16-bit timer channel can generate a compare match/input capture A interrupt, a compare
match/input capture B interrupt, and an overflow interrupt. In total there are nine interrupt
sources of three kinds, all independently vectored. An interrupt is requested when the interrupt
request flag are set to 1.
The priority order of the channels can be modified in interrupt priority registers A (IPRA). For
details see section 5, Interrupt Controller.
Table 9.6 lists the interrupt sources.
Table 9.6
16-bit timer Interrupt Sources
Interrupt
Source
Description
Priority*
0
IMIA0
IMIB0
OVI0
Compare match/input capture A0
Compare match/input capture B0
Overflow 0
High
1
IMIA1
IMIB1
OVI1
Compare match/input capture A1
Compare match/input capture B1
Overflow 1
2
IMIA2
IMIB2
OVI2
Compare match/input capture A2
Compare match/input capture B2
Overflow 2
Channel
Low
Note: * The priority immediately after a reset is indicated. Inter-channel priorities can be changed
by settings in IPRA.
Rev. 3.00 Sep 14, 2005 page 373 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
9.6
Usage Notes
This section describes contention and other matters requiring special attention during 16-bit timer
operations.
Contention between 16TCNT Write and Clear: If a counter clear signal occurs in the T3 state
of a 16TCNT write cycle, clearing of the counter takes priority and the write is not performed.
See
figure 9.37.
16TCNT write cycle
T2
T1
T3
φ
Address bus
16TCNT address
Internal write signal
Counter clear signal
16TCNT
N
H'0000
Figure 9.37 Contention between 16TCNT Write and Clear
Rev. 3.00 Sep 14, 2005 page 374 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between 16TCNT Word Write and Increment: If an increment pulse occurs in the
T3 state of a 16TCNT word write cycle, writing takes priority and 16TCNT is not incremented.
Figure 9.38 shows the timing in this case.
16TCNT word write cycle
T2
T1
T3
φ
Address bus
16TCNT address
Internal write signal
16TCNT input clock
16TCNT
N
M
16TCNT write data
Figure 9.38 Contention between 16TCNT Word Write and Increment
Rev. 3.00 Sep 14, 2005 page 375 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between 16TCNT Byte Write and Increment: If an increment pulse occurs in the
T2 or T3 state of a 16TCNT byte write cycle, writing takes priority and 16TCNT is not
incremented. The byte data for which a write was not performed is not incremented, and retains
its pre-write value. See figure 9.39, which shows an increment pulse occurring in the T2 state of a
byte write to 16TCNTH.
16TCNTH byte write cycle
T1
T2
T3
φ
16TCNTH address
Address bus
Internal write signal
16TCNT input clock
16TCNTH
N
M
16TCNT write data
16TCNTL
X
X+1
X
Figure 9.39 Contention between 16TCNT Byte Write and Increment
Rev. 3.00 Sep 14, 2005 page 376 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between General Register Write and Compare Match: If a compare match occurs
in the T3 state of a general register write cycle, writing takes priority and the compare match
signal is inhibited. See figure 9.40.
General register write cycle
T1
T2
T3
φ
GR address
Address bus
Internal write signal
16TCNT
N
GR
N
N+1
M
General register write data
Compare match signal
Inhibited
Figure 9.40 Contention between General Register Write and Compare Match
Rev. 3.00 Sep 14, 2005 page 377 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between 16TCNT Write and Overflow or Underflow: If an overflow occurs in the
T3 state of a 16TCNT write cycle, writing takes priority and the counter is not incremented. OVF
is set to 1.The same holds for underflow. See figure 9.41.
16TCNT write cycle
T1
T2
T3
φ
Address bus
16TCNT address
Internal write signal
16TCNT input clock
Overflow signal
16TCNT
H'FFFF
M
16TCNT write data
OVF
Figure 9.41 Contention between 16TCNT Write and Overflow
Rev. 3.00 Sep 14, 2005 page 378 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between General Register Read and Input Capture: If an input capture signal
occurs during the T3 state of a general register read cycle, the value before input capture is read.
See figure 9.42.
General register read cycle
T2
T1
T3
φ
GR address
Address bus
Internal read signal
Input capture signal
GR
Internal data bus
X
M
X
Figure 9.42 Contention between General Register Read and Input Capture
Rev. 3.00 Sep 14, 2005 page 379 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between Counter Clearing by Input Capture and Counter Increment: If an input
capture signal and counter increment signal occur simultaneously, the counter is cleared
according to the input capture signal. The counter is not incremented by the increment signal.
The value before the counter is cleared is transferred to the general register. See figure 9.43.
φ
Input capture signal
Counter clear signal
16TCNT input clock
16TCNT
GR
N
H'0000
N
Figure 9.43 Contention between Counter Clearing by Input Capture and Counter
Increment
Rev. 3.00 Sep 14, 2005 page 380 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Contention between General Register Write and Input Capture: If an input capture signal
occurs in the T3 state of a general register write cycle, input capture takes priority and the write to
the general register is not performed. See figure 9.44.
General register write cycle
T1
T2
T3
φ
Address bus
GR address
Internal write signal
Input capture signal
16TCNT
GR
M
M
Figure 9.44 Contention between General Register Write and Input Capture
Rev. 3.00 Sep 14, 2005 page 381 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Note on Waveform Period Setting: When a counter is cleared by compare match, the counter is
cleared in the last state at which the 16TCNT value matches the general register value, at the time
when this value would normally be updated to the next count. The actual counter frequency is
therefore given by the following formula:
f=
φ
(N+1)
(f: counter frequency. φ: system clock frequency. N: value set in general register.)
Note on Writes in Synchronized Operation: When channels are synchronized, if a 16TCNT
value is modified by byte write access, all 16 bits of all synchronized counters assume the same
value as the counter that was addressed.
(Example) When channels 1 and 2 are synchronized
• Byte write to channel 1 or byte write to channel 2
16TCNT1
W
X
16TCNT2
Y
Z
Upper byte Lower byte
Write A to upper byte
of channel 1
16TCNT1
A
X
16TCNT2
A
X
Upper byte Lower byte
Write A to lower byte
of channel 2
16TCNT1
Y
A
16TCNT2
Y
A
Upper byte Lower byte
• Word write to channel 1 or word write to channel 2
16TCNT1
W
X
16TCNT2
Y
Z
Write AB word to
channel 1 or 2
Upper byte Lower byte
Rev. 3.00 Sep 14, 2005 page 382 of 910
REJ09B0258-0300
16TCNT1
A
B
16TCNT2
A
B
Upper byte Lower byte
Section 9 16-Bit Timer
16-bit timer Operating Modes
Table 9.7 (a) 16-bit timer Operating Modes (Channel 0)
Register Settings
TSNC
TMDR
TIOR0
16TCR0
Operating Mode
Synchronization
Synchronous preset
SYNC0 = 1 —
—
PWM mode
—
—
PWM0 = 1
—
Output compare A
—
—
PWM0 = 0
IOA2 = 0
Other bits
unrestricted
Output compare B
—
—
Input capture A
—
—
PWM0 = 0
Input capture B
—
—
PWM0 = 0
Counter By compare
clearing match/input
capture A
—
—
CCLR1 = 0
CCLR0 = 1
By compare
match/input
capture B
—
—
CCLR1 = 1
CCLR0 = 0
SYNC0 = 1 —
—
CCLR1 = 1
CCLR0 = 1
Synchronous
clear
Legend:
MDF
FDIR PWM
IOA
IOB
Clear
Select
Clock
Select
*
IOB2 = 0
Other bits
unrestricted
IOA2 = 1
Other bits
unrestricted
IOB2 = 1
Other bits
unrestricted
Setting available (valid). — Setting does not affect this mode.
Note: * The input capture function cannot be used in PWM mode. If compare match A and compare match B occur
simultaneously, the compare match signal is inhibited.
Rev. 3.00 Sep 14, 2005 page 383 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Table 9.7 (b) 16-bit timer Operating Modes (Channel 1)
Register Settings
TSNC
TMDR
TIOR1
16TCR1
Operating Mode
Synchronization
Synchronous preset
SYNC1 = 1 —
—
PWM mode
—
—
PWM1 = 1
—
Output compare A
—
—
PWM1 = 0
IOA2 = 0
Other bits
unrestricted
Output compare B
—
—
Input capture A
—
—
PWM1 = 0
Input capture B
—
—
PWM1 = 0
Counter By compare
clearing match/input
capture A
—
—
CCLR1 = 0
CCLR0 = 1
By compare
match/input
capture B
—
—
CCLR1 = 1
CCLR0 = 0
SYNC1 = 1 —
—
CCLR1 = 1
CCLR0 = 1
Synchronous
clear
MDF
FDIR PWM
IOA
IOB
Clear
Select
Clock
Select
*
IOB2 = 0
Other bits
unrestricted
IOA2 = 1
Other bits
unrestricted
IOB2 = 1
Other bits
unrestricted
Legend:
Setting available (valid). — Setting does not affect this mode.
Note: * The input capture function cannot be used in PWM mode. If compare match A and compare match B
occur simultaneously, the compare match signal is inhibited.
Rev. 3.00 Sep 14, 2005 page 384 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Table 9.7 (c)
16-bit timer Operating Modes (Channel 2)
Register Settings
TSNC
Operating Mode
Synchronization
Synchronous preset
SYNC2 = 1
TMDR
MDF
FDIR PWM
TIOR2
IOA
IOB
16TCR2
Clear
Select
—
*
PWM mode
—
PWM2 = 1
—
Output compare A
—
PWM2 = 0
IOA2 = 0
Other bits
unrestricted
Output compare B
—
Input capture A
—
PWM2 = 0
Input capture B
—
PWM2 = 0
Counter By compare
clearing match/input
capture A
—
CCLR1 = 0
CCLR0 = 1
By compare
match/input
capture B
—
CCLR1 = 1
CCLR0 = 0
—
CCLR1 = 1
CCLR0 = 1
Synchronous
clear
Phase counting
mode
Clock
Select
SYNC2 = 1
MDF = 1
IOB2 = 0
Other bits
unrestricted
IOA2 = 1
Other bits
unrestricted
IOB2 = 1
Other bits
unrestricted
—
Legend:
Setting available (valid). — Setting does not affect this mode.
Note: * The input capture function cannot be used in PWM mode. If compare match A and compare match B occur
simultaneously, the compare match signal is inhibited.
Rev. 3.00 Sep 14, 2005 page 385 of 910
REJ09B0258-0300
Section 9 16-Bit Timer
Rev. 3.00 Sep 14, 2005 page 386 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Section 10 8-Bit Timers
10.1
Overview
The H8/3068F has a built-in 8-bit timer module with four channels (TMR0, TMR1, TMR2, and
TMR3), based on 8-bit counters. Each channel has an 8-bit timer counter (8TCNT) and two 8-bit
time constant registers (TCORA and TCORB) that are constantly compared with the 8TCNT
value to detect compare match events. The timers can be used as multifunctional timers in a
variety of applications, including the generation of a rectangular-wave output with an arbitrary
duty cycle.
10.1.1
Features
The features of the 8-bit timer module are listed below.
• Selection of four clock sources
The counters can be driven by one of three internal clock signals (φ/8, φ/64, or φ/8192) or an
external clock input (enabling use as an external event counter).
• Selection of three ways to clear the counters
The counters can be cleared on compare match A or B, or input capture B.
• Timer output controlled by two compare match signals
The timer output signal in each channel is controlled by two independent compare match
signals, enabling the timer to generate output waveforms with an arbitrary duty cycle or PWM
output.
• A/D converter can be activated by a compare match
• Two channels can be cascaded
 Channels 0 and 1 can be operated as the upper and lower halves of a 16-bit timer (16-bit
count mode).
 Channels 2 and 3 can be operated as the upper and lower halves of a 16-bit timer (16-bit
count mode).
 Channel 1 can count channel 0 compare match events (compare match count mode).
 Channel 3 can count channel 2 compare match events (compare match count mode).
• Input capture function can be set
8-bit or 16-bit input capture operation is available.
Rev. 3.00 Sep 14, 2005 page 387 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
• Twelve interrupt sources
There are twelve interrupt sources: four compare match sources, four compare match/input
capture sources, four overflow sources.
Two of the compare match sources and two of the combined compare match/input capture
sources each have an independent interrupt vector. The remaining compare match interrupts,
combined compare match/input capture interrupts, and overflow interrupts have one interrupt
vector for two sources.
Rev. 3.00 Sep 14, 2005 page 388 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.1.2
Block Diagram
The 8-bit timers are divided into two groups of two channels each: group 0 comprising channels 0
and 1, and group 1 comprising channels 2 and 3. Figure 10.1 shows a block diagram of 8-bit
timer group 0.
External clock
sources
TCLKA
TCLKC
Internal clock
sources
φ/8
φ/64
φ/8192
Clock 1
Clock 0
Clock select
TCORA0
TCORA1
Compare match A1
Compare match A0 Comparator A0
Comparator A1
Overflow 1
TMO0
TMIO1
8TCNT0
8TCNT1
Internal bus
Overflow 0
Compare match B1
Control logic
Compare match B0 Comparator B0
Input capture B1
Legend:
TCORA:
TCORB:
8TCNT:
8TCSR:
8TCR:
Comparator B1
TCORB0
TCORB1
8TCSR0
8TCSR1
8TCR0
8TCR1
CMIA0
CMIB0
CMIA1/CMIB1
OVI0/OVI1
Interrupt signals
Time constant register A
Time constant register B
Timer counter
Timer control/status register
Timer control register
Figure 10.1 Block Diagram of 8-Bit Timer Unit (Two Channels: Group 0)
Rev. 3.00 Sep 14, 2005 page 389 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.1.3
Pin Configuration
Table 10.1 summarizes the input/output pins of the 8-bit timer module.
Table 10.1 8-Bit Timer Pins
Group
Channel Name
Abbreviation I/O
0
0
Timer output
TMO0
Output Compare match output
Timer clock input
TCLKC
Input
Counter external clock input
Timer input/output TMIO1
I/O
Compare match output/input
capture input
Timer clock input
TCLKA
Input
Counter external clock input
Timer output
TMO2
Output Compare match output
Timer clock input
TCLKD
Input
Counter external clock input
Timer input/output TMIO3
I/O
Compare match output/input
capture input
Timer clock input
Input
Counter external clock input
1
1
2
3
TCLKB
Rev. 3.00 Sep 14, 2005 page 390 of 910
REJ09B0258-0300
Function
Section 10 8-Bit Timers
10.1.4
Register Configuration
Table 10.2 summarizes the registers of the 8-bit timer module.
Table 10.2 8-Bit Timer Registers
Channel
Address*1
Name
Abbreviation R/W
0
H'FFF80
Timer control register 0
8TCR0
1
2
3
Initial value
R/W
H'00
2
H'FFF82
Timer control/status register 0
8TCSR0
R/(W)* H'00
H'FFF84
Time constant register A0
TCORA0
R/W
H'FF
H'FFF86
Time constant register B0
TCORB0
R/W
H'FF
H'FFF88
Timer counter 0
8TCNT0
R/W
H'00
H'FFF81
Timer control register 1
8TCR1
R/W
H'00
2
H'FFF83
Timer control/status register 1
8TCSR1
R/(W)* H'00
H'FFF85
Time constant register A1
TCORA1
R/W
H'FF
H'FFF87
Time constant register B1
TCORB1
R/W
H'FF
H'FFF89
Timer counter 1
8TCNT1
R/W
H'00
H'FFF90
Timer control register 2
8TCR2
R/W
H'00
2
H'FFF92
Timer control/status register 2
8TCSR2
R/(W)* H'10
H'FFF94
Time constant register A2
TCORA2
R/W
H'FF
H'FFF96
Time constant register B2
TCORB2
R/W
H'FF
H'FFF98
Timer counter 2
8TCNT2
R/W
H'00
H'FFF91
Timer control register 3
8TCR3
R/W
H'00
H'FFF93
Timer control/status register 3
8TCSR3
R/(W)*2 H'00
H'FFF95
Time constant register A3
TCORA3
R/W
H'FF
H'FFF97
Time constant register B3
TCORB3
R/W
H'FF
H'FFF99
Timer counter 3
8TCNT3
R/W
H'00
Notes: 1. Indicates the lower 20 bits of the address in advanced mode.
2. Only 0 can be written to bits 7 to 5, to clear these flags.
Each pair of registers for channel 0 and channel 1 comprises a 16-bit register with the channel 0
register as the upper 8 bits and the channel 1 register as the lower 8 bits, so they can be accessed
together by word access.
Similarly, each pair of registers for channel 2 and channel 3 comprises a 16-bit register with the
channel 2 register as the upper 8 bits and the channel 3 register as the lower 8 bits, so they can be
accessed together by word access.
Rev. 3.00 Sep 14, 2005 page 391 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.2
Register Descriptions
10.2.1
Timer Counters (8TCNT)
8TCNT0
8TCNT1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
8TCNT2
Bit
Initial value
Read/Write
8TCNT3
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
The timer counters (8TCNT) are 8-bit readable/writable up-counters that increment on pulses
generated from an internal or external clock source. The clock source is selected by clock select
bits 2 to 0 (CKS2 to CKS0) in the timer control register (8TCR). The CPU can always read or
write to the timer counters.
The 8TCNT0 and 8TCNT1 pair, and the 8TCNT2 and 8TCNT3 pair, can each be accessed as a
16-bit register by word access.
8TCNT can be cleared by an input capture signal or compare match signal. Counter clear bits 1
and 0 (CCLR1 and CCLR0) in 8TCR select the method of clearing.
When 8TCNT overflows from H'FF to H'00, the overflow flag (OVF) in the timer control/status
register (8TCSR) is set to 1.
Each 8TCNT is initialized to H'00 by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 392 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.2.2
Time Constant Registers A (TCORA)
TCORA0 to TCORA3 are 8-bit readable/writable registers.
TCORA0
Bit
Initial value
Read/Write
TCORA1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
TCORA2
TCORA3
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
The TCORA0 and TCORA1 pair, and the TCORA2 and TCORA3 pair, can each be accessed as a
16-bit register by word access.
The TCORA value is constantly compared with the 8TCNT value. When a match is detected, the
corresponding compare match flag A (CMFA) is set to 1 in 8TCSR.
The timer output can be freely controlled by these compare match signals and the settings of
output select bits 1 and 0 (OS1, OS0) in 8TCSR.
Each TCORA register is initialized to H'FF by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 393 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.2.3
Time Constant Registers B (TCORB)
TCORB0
TCORB1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
TCORB2
TCORB3
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
TCORB0 to TCORB3 are 8-bit readable/writable registers. The TCORB0 and TCORB1 pair, and
the TCORB2 and TCORB3 pair, can each be accessed as a 16-bit register by word access.
The TCORB value is constantly compared with the 8TCNT value. When a match is detected, the
corresponding compare match flag B (CMFB) is set to 1 in 8TCSR*.
The timer output can be freely controlled by these compare match signals and the settings of
output/input capture edge select bits 3 and 2 (OIS3, OIS2) in 8TCSR.
When TCORB is used for input capture, it stores the 8TCNT value on detection of an external
input capture signal. At this time, the CMFB flag is set to 1 in the corresponding 8TCSR register.
The detected edge of the input capture signal is set in 8TCSR.
Each TCORB register is initialized to H'FF by a reset and in standby mode.
Note: * When channel 1 and channel 3 are designated for TCORB input capture, the CMFB flag
is not set by a channel 0 or channel 2 compare match B.
Rev. 3.00 Sep 14, 2005 page 394 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.2.4
Timer Control Register (8TCR)
Bit
7
6
5
4
3
2
1
0
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
8TCR is an 8-bit readable/writable register that selects the 8TCNT input clock, gives the 8TCNT
clearing specification, and enables interrupt requests.
8TCR is initialized to H'00 by a reset and in standby mode.
For the timing, see section 10.4, Operation.
Bit 7—Compare Match Interrupt Enable B (CMIEB): Enables or disables the CMIB interrupt
request when the CMFB flag is set to 1 in 8TCSR.
Bit 7
CMIEB
Description
0
CMIB interrupt requested by CMFB is disabled
1
CMIB interrupt requested by CMFB is enabled
(Initial value)
Bit 6—Compare Match Interrupt Enable A (CMIEA): Enables or disables the CMIA
interrupt request when the CMFA flag is set to 1 in 8TCSR.
Bit 6
CMIEA
Description
0
CMIA interrupt requested by CMFA is disabled
1
CMIA interrupt requested by CMFA is enabled
(Initial value)
Bit 5—Timer Overflow Interrupt Enable (OVIE): Enables or disables the OVI interrupt
request when the OVF flag is set to 1 in 8TCSR.
Bit 5
OVIE
Description
0
OVI interrupt requested by OVF is disabled
1
OVI interrupt requested by OVF is enabled
(Initial value)
Rev. 3.00 Sep 14, 2005 page 395 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Bits 4 and 3—Counter Clear 1 and 0 (CCLR1, CCLR0): These bits specify the 8TCNT
clearing source. Compare match A or B, or input capture B, can be selected as the clearing
source.
Bit 4
CCLR1
Bit 3
CCLR0
Description
0
0
Clearing is disabled
1
Cleared by compare match A
1
0
Cleared by compare match B/input capture B
1
Cleared by input capture B
(Initial value)
Note: When input capture B is set as the 8TCNT1 and 8TCNT3 counter clear source, 8TCNT0
and 8TCNT2 are not cleared by compare match B.
Bits 2 to 0—Clock Select 2 to 0 (CSK2 to CSK0): These bits select whether the clock input to
8TCNT is an internal or external clock.
Three internal clocks can be selected, all divided from the system clock (φ): φ/8, φ/64, and
φ/8192. The rising edge of the selected internal clock triggers the count.
When use of an external clock is selected, three types of count can be selected: at the rising edge,
the falling edge, and both rising and falling edges.
When CKS2, CKS1, CKS0 = 1, 0, 0, channels 0 and 1 and channels 2 and 3 are cascaded.
The incrementing clock source is different when 8TCR0 and 8TCR2 are set, and when 8TCR1
and 8TCR3 are set.
Rev. 3.00 Sep 14, 2005 page 396 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Bit 2
CSK2
Bit 1
CSK1
Bit 0
CSK0
Description
0
0
0
Clock input disabled
1
Internal clock, counted on falling edge of φ/8
0
Internal clock, counted on falling edge of φ/64
1
Internal clock, counted on falling edge of φ/8192
0
Channel 0 (16-bit count mode): Count on 8TCNT1 overflow
1
signal*
1
1
0
(Initial value)
Channel 1 (compare match count mode): Count on 8TCNT0
1
compare match A*
Channel 2 (16-bit count mode): Count on 8TCNT3 overflow
2
signal*
Channel 3 (compare match count mode): Count on 8TCNT2
2
compare match A*
1
1
External clock, counted on rising edge
0
External clock, counted on falling edge
1
External clock, counted on both rising and falling edges
Notes: 1. If the clock input of channel 0 is the 8TCNT1 overflow signal and that of channel 1 is
the 8TCNT0 compare match signal, no incrementing clock is generated. Do not use
this setting.
2. If the clock input of channel 2 is the 8TCNT3 overflow signal and that of channel 3 is
the 8TCNT2 compare match signal, no incrementing clock is generated. Do not use
this setting.
Rev. 3.00 Sep 14, 2005 page 397 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.2.5
Timer Control/Status Registers (8TCSR)
8TCSR0
Bit
7
6
5
4
3
2
1
0
CMFB
CMFA
OVF
ADTE
OIS3
OIS2
OS1
OS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
CMFB
CMFA
OVF
—
OIS3
OIS2
OS1
OS0
8TCSR2
Bit
Initial value
0
0
0
1
0
0
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
—
R/W
R/W
R/W
R/W
6
5
4
3
2
1
0
8TCSR1, 8TCSR3
7
Bit
CMFB
CMFA
OVF
ICE
OIS3
OIS2
OS1
OS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/W
R/W
R/W
R/W
R/W
Note: * Only 0 can be written to bits 7 to 5, to clear these flags.
The timer control/status registers 8TCSR are 8-bit registers that indicate compare match/input
capture and overflow statuses, and control compare match output/input capture edge selection.
8TCSR2 is initialized to H'10, and 8TCSR0, 8TCSR1, and 8TCSR3 to H'00, by a reset and in
standby mode.
Rev. 3.00 Sep 14, 2005 page 398 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Bit 7—Compare Match/Input Capture Flag B (CMFB): Status flag that indicates the
occurrence of a TCORB compare match or input capture.
Bit 7
CMFB
0
1
Description
[Clearing condition]
Read CMFB when CMFB = 1, then write 0 in CMFB
(Initial value)
[Setting conditions]
• 8TCNT = TCORB*
• The 8TCNT value is transferred to TCORB by an input capture signal
when TCORB functions as an input capture register
Note: * When bit ICE is set to 1 in 8TCSR1 and 8TCSR3, the CMFB flag is not set when 8TCNT0
= TCORB0 or 8TCNT2 = TCORB2.
Bit 6—Compare Match Flag A (CMFA): Status flag that indicates the occurrence of a TCORA
compare match.
Bit 6
CMFA
Description
0
[Clearing condition]
Read CMFA when CMFA = 1, then write 0 in CMFA
1
[Setting condition]
8TCNT = TCORA
(Initial value)
Bit 5—Timer Overflow Flag (OVF): Status flag that indicates that the 8TCNT has overflowed
from H'FF to H'00.
Bit 5
OVF
Description
0
[Clearing condition]
Read OVF when OVF = 1, then write 0 in OVF
1
[Setting condition]
8TCNT overflows from H'FF to H'00
(Initial value)
Rev. 3.00 Sep 14, 2005 page 399 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Bit 4—A/D Trigger Enable (ADTE) (In 8TCSR0): In combination with TRGE in the A/D
control register (ADCR), enables or disables A/D converter start requests by compare match A or
an external trigger.
TRGE*
Bit 4
ADTE
0
0
A/D converter start requests by compare match A or external trigger pin
(ADTRG) input are disabled
(Initial value)
1
A/D converter start requests by compare match A or external trigger pin
(ADTRG) input are disabled
1
0
1
Description
A/D converter start requests by external trigger pin (ADTRG) input are
enabled, and A/D converter start requests by compare match A are disabled
A/D converter start requests by compare match A are enabled, and A/D
converter start requests by external trigger pin (ADTRG) input are disabled
Note: * TRGE is bit 7 of the A/D control register (ADCR).
Bit 4—Reserved (In 8TCSR1): This bit is a reserved bit, but can be read and written.
Bit 4—Input Capture Enable (ICE) (In 8TCSR1 and 8TCSR3): Selects the function of
TCORB1 and TCORB3.
Bit 4
ICE
Description
0
TCORB1 and TCORB3 are compare match registers
1
TCORB1 and TCORB3 are input capture registers
(Initial value)
When bit ICE is set to 1 in 8TCSR1 or 8TCSR3, the operation of the TCORA and TCORB
registers in channels 0 to 3 is as shown in the tables below.
Rev. 3.00 Sep 14, 2005 page 400 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Table 10.3 Operation of Channels 0 and 1 when Bit ICE is Set to 1 in 8TCSR1 Register
Register
Register Function
Status Flag Change
Timer Output
Capture Input
Interrupt Request
TCORA0 Compare match CMFA changed from 0 TMO0 output
controllable
operation
to 1 in 8TCSR0 by
compare match
CMIA0 interrupt request
generated by compare
match
TCORB0 Compare match CMFB not changed
No output from
operation
from 0 to 1 in 8TCSR0 TMO0
by compare match
CMIB0 interrupt request
not generated by compare
match
TCORA1 Compare match CMFA changed from 0 TMIO1 is
operation
to 1 in 8TCSR1 by
dedicated input
compare match
capture pin
CMIA1 interrupt request
generated by compare
match
TCORB1 Input capture
operation
CMIB1 interrupt request
generated by input
capture
CMFB changed from 0 TMIO1 is
to 1 in 8TCSR1 by
dedicated input
input capture
capture pin
Table 10.4 Operation of Channels 2 and 3 when Bit ICE is Set to 1 in 8TCSR3 Register
Register
Register Function
Status Flag Change
Timer Output
Capture Input
Interrupt Request
TCORA2 Compare match CMFA changed from 0 TMO2 output
operation
to 1 in 8TCSR2 by
controllable
compare match
CMIA2 interrupt request
generated by compare
match
TCORB2 Compare match CMFB not changed
No output from
operation
from 0 to 1 in 8TCSR2 TMO2
by compare match
CMIB2 interrupt request
not generated by compare
match
TCORA3 Compare match CMFA changed from 0 TMIO3 is
operation
to 1 in 8TCSR3 by
dedicated input
compare match
capture pin
CMIA3 interrupt request
generated by compare
match
TCORB3 Input capture
operation
CMIB3 interrupt request
generated by input
capture
CMFB changed from 0 TMIO3 is
to 1 in 8TCSR3 by
dedicated input
input capture
capture pin
Rev. 3.00 Sep 14, 2005 page 401 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Bits 3 and 2—Output/Input Capture Edge Select B3 and B2 (OIS3, OIS2): In combination
with the ICE bit in 8TCSR1 (8TCSR3), these bits select the compare match B output level or the
input capture input detected edge.
The function of TCORB1 (TCORB3) depends on the setting of bit 4 of 8TCSR1 (8TCSR3).
ICE Bit in
8TCSR1
(8TCSR3)
Bit 3
OIS3
Bit 2
OIS2
Description
0
0
0
No change when compare match B occurs
1
0 is output when compare match B occurs
0
1 is output when compare match B occurs
1
Output is inverted when compare match B occurs (toggle output)
0
TCORB input capture on rising edge
1
TCORB input capture on falling edge
0
TCORB input capture on both rising and falling edges
1
1
0
1
(Initial value)
1
• When the compare match register function is used, the timer output priority order is: toggle
output > 1 output > 0 output.
• If compare match A and B occur simultaneously, the output changes in accordance with the
higher-priority compare match.
• When bits OIS3, OIS2, OS1, and OS0 are all cleared to 0, timer output is disabled.
Bits 1 and 0—Output Select A1 and A0 (OS1, OS0): These bits select the compare match A
output level.
Bit 1
OS1
Bit 0
OS0
Description
0
0
No change when compare match A occurs
1
0 is output when compare match A occurs
0
1 is output when compare match A occurs
1
Output is inverted when compare match A occurs (toggle output)
1
(Initial value)
• When the compare match register function is used, the timer output priority order is: toggle
output > 1 output > 0 output.
• If compare match A and B occur simultaneously, the output changes in accordance with the
higher-priority compare match.
• When bits OIS3, OIS2, OS1, and OS0 are all cleared to 0, timer output is disabled.
Rev. 3.00 Sep 14, 2005 page 402 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.3
CPU Interface
10.3.1
8-Bit Registers
8TCNT, TCORA, TCORB, 8TCR, and 8TCSR are 8-bit registers. These registers are connected
to the CPU by an internal 16-bit data bus and can be read and written a word at a time or a byte at
a time.
Figures 10.2 and 10.3 show the operation in word read and write accesses to 8TCNT.
Figures 10.4 to 10.7 show the operation in byte read and write accesses to 8TCNT0 and 8TCNT1.
Internal data bus
H
C
P
U
H
Bus
interface
L
L
Module data bus
8TCNT0 8TCNT1
Figure 10.2 8TCNT Access Operation (CPU Writes to 8TCNT, Word)
Internal data bus
H
C
P
U
L
H
Bus
interface
L
Module data bus
8TCNT0 8TCNT1
Figure 10.3 8TCNT Access Operation (CPU Reads 8TCNT, Word)
Rev. 3.00 Sep 14, 2005 page 403 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Internal data bus
H
C
P
U
L
H
Bus
interface
L
Module data bus
8TCNTH0 8TCNTL1
Figure 10.4 8TCNT0 Access Operation (CPU Writes to 8TCNT0, Upper Byte)
Internal data bus
H
C
P
U
L
H
Bus
interface
L
Module data bus
8TCNTH0 8TCNTL1
Figure 10.5 8TCNT1 Access Operation (CPU Writes to 8TCNT1, Lower Byte)
Internal data bus
H
C
P
U
L
H
Bus
interface
L
Module data bus
8TCNT0 8TCNT1
Figure 10.6 8TCNT0 Access Operation (CPU Reads 8TCNT0, Upper Byte)
Internal data bus
H
C
P
U
L
H
Bus
interface
L
Module data bus
8TCNT0 8TCNT1
Figure 10.7 8TCNT1 Access Operation (CPU Reads 8TCNT1, Lower Byte)
Rev. 3.00 Sep 14, 2005 page 404 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.4
Operation
10.4.1
8TCNT Count Timing
8TCNT is incremented by input clock pulses (either internal or external).
Internal Clock: Three different internal clock signals (φ/8, φ/64, or φ/8192) divided from the
system clock (φ) can be selected, by setting bits CKS2 to CKS0 in 8TCR. Figure 10.8 shows the
count timing.
φ
Internal clock
8TCNT input clock
8TCNT
N–1
N
N+1
Note: Even if the same internal clock is selected for the 16-bit timer and the 8-bit timer, the same operation
will not be performed since the incrementing edge is different in each case.
Figure 10.8 Count Timing for Internal Clock Input
External Clock: Three incrementation methods can be selected by setting bits CKS2 to CKS0 in
8TCR: on the rising edge, the falling edge, and both rising and falling edges.
The pulse width of the external clock signal must be at least 1.5 system clocks when a single
edge is selected, and at least 2.5 system clocks when both edges are selected. Shorter pulses will
not be counted correctly.
Figure 10.9 shows the timing for incrementation on both edges of the external clock signal.
Rev. 3.00 Sep 14, 2005 page 405 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
φ
External clock input
8TCNT input clock
8TCNT
N–1
N
N+1
Figure 10.9 Count Timing for External Clock Input (Both-Edge Detection)
10.4.2
Compare Match Timing
Timer Output Timing: When compare match A or B occurs, the timer output is as specified by
the OIS3, OIS2, OS1, and OS0 bits in 8TCSR (unchanged, 0 output, 1 output, or toggle output).
Figure 10.10 shows the timing when the output is set to toggle on compare match A.
φ
Compare match A
signal
Timer output
Figure 10.10 Timing of Timer Output
Rev. 3.00 Sep 14, 2005 page 406 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Clear by Compare Match: Depending on the setting of the CCLR1 and CCLR0 bits in 8TCR,
8TCNT can be cleared when compare match A or B occurs, Figure 10.11 shows the timing of
this operation.
φ
Compare match signal
8TCNT
N
H'00
Figure 10.11 Timing of Clear by Compare Match
Clear by Input Capture: Depending on the setting of the CCLR1 and CCLR0 bits in 8TCR,
8TCNT can be cleared when input capture B occurs. Figure 10.12 shows the timing of this
operation.
φ
Input capture input
Input capture signal
8TCNT
N
H '00
Figure 10.12 Timing of Clear by Input Capture
10.4.3
Input Capture Signal Timing
Input capture on the rising edge, falling edge, or both edges can be selected by settings in 8TCSR.
Figure 10.13 shows the timing when the rising edge is selected.
The pulse width of the input capture input signal must be at least 1.5 system clocks when a single
edge is selected, and at least 2.5 system clocks when both edges are selected.
Rev. 3.00 Sep 14, 2005 page 407 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
φ
Input capture input
Input capture signal
8TCNT
N
TCORB
N
Figure 10.13 Timing of Input Capture Input Signal
10.4.4
Timing of Status Flag Setting
Timing of CMFA/CMFB Flag Setting when Compare Match Occurs: The CMFA and CMFB
flags in 8TCSR are set to 1 by the compare match signal output when the TCORA or TCORB and
8TCNT values match. The compare match signal is generated in the last state of the match (when
the matched 8TCNT count value is updated). Therefore, after the 8TCNT and TCORA or
TCORB values match, the compare match signal is not generated until an incrementing clock
pulse signal is generated. Figure 10.14 shows the timing in this case.
φ
8TCNT
N
TCOR
N
N+1
Compare match signal
CMF
Figure 10.14 CMF Flag Setting Timing when Compare Match Occurs
Rev. 3.00 Sep 14, 2005 page 408 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Timing of CMFB Flag Setting when Input Capture Occurs: On generation of an input capture
signal, the CMFB flag is set to 1 and at the same time the 8TCNT value is transferred to TCORB.
Figure 10.15 shows the timing in this case.
φ
8TCNT
N
TCORB
N
Input capture signal
CMFB
Figure 10.15 CMFB Flag Setting Timing when Input Capture Occurs
Timing of Overflow Flag (OVF) Setting: The OVF flag in 8TCSR is set to 1 by the overflow
signal generated when 8TCNT overflows (from H'FF to H'00). Figure 10.16 shows the timing in
this case.
φ
8TCNT
H'FF
H'00
Overflow signal
OVF
Figure 10.16 Timing of OVF Setting
10.4.5
Operation with Cascaded Connection
If bits CKS2 to CKS0 are set to (100) in either 8TCR0 or 8TCR1, the 8-bit timers of channels 0
and 1 are cascaded. With this configuration, the two timers can be used as a single 16-bit timer
(16-bit timer mode), or channel 0 8-bit timer compare matches can be counted in channel 1
(compare match count mode). Similarly, if bits CKS2 to CKS0 are set to (100) in either 8TCR2
Rev. 3.00 Sep 14, 2005 page 409 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
or 8TCR3, the 8-bit timers of channels 2 and 3 are cascaded. With this configuration, the two
timers can be used as a single 16-bit timer (16-bit timer mode),or channel 2 8-bit timer compare
matches can be counted in channel 3 (compare match count mode). In this case, the timer
operates as below.
16-Bit Count Mode
• Channels 0 and 1:
When bits CKS2 to CKS0 are set to (100) in 8TCR0, the timer functions as a single 16-bit
timer with channel 0 occupying the upper 8 bits and channel 1 occupying the lower 8 bits.
 Setting when Compare Match Occurs
• The CMFA or CMFB flag is set to 1 in 8TCSR0 when a 16-bit compare match occurs.
• The CMFA or CMFB flag is set to 1 in 8TCSR1 when a lower 8-bit compare match
occurs.
• TMO0 pin output control by bits OIS3, OIS2, OS1, and OS0 in 8TCSR0 is in accordance
with the 16-bit compare match conditions.
• TMIO1 pin output control by bits OIS3, OIS2, OS1, and OS0 in 8TCSR1 is in
accordance with the lower 8-bit compare match conditions.
 Setting when Input Capture Occurs
• The CMFB flag is set to 1 in 8TCSR0 and 8TCSR1 when the ICE bit is 1 in TCSR1 and
input capture occurs.
• TMIO1 pin input capture input signal edge detection is selected by bits OIS3 and OIS2 in
8TCSR0.
 Counter Clear Specification
• If counter clear on compare match or input capture has been selected by the CCLR1 and
CCLR0 bits in 8TCR0, the 16-bit counter (both 8TCNT0 and 8TCNT1) is cleared.
• The settings of the CCLR1 and CCLR0 bits in 8TCR1 are ignored. The lower 8 bits
cannot be cleared independently.
 OVF Flag Operation
• The OVF flag is set to 1 in 8TCSR0 when the 16-bit counter (8TCNT0 and 8TCNT1)
overflows (from H'FFFF to H'0000).
• The OVF flag is set to 1 in 8TCSR1 when the 8-bit counter (8TCNT1) overflows (from
H'FF to H'00).
Rev. 3.00 Sep 14, 2005 page 410 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
• Channels 2 and 3:
When bits CKS2 to CKS0 are set to (100) in 8TCR2, the timer functions as a single 16-bit
timer with channel 2 occupying the upper 8 bits and channel 3 occupying the lower 8 bits.
 Setting when Compare Match Occurs
• The CMFA or CMFB flag is set to 1 in 8TCSR2 when a 16-bit compare match occurs.
• The CMFA or CMFB flag is set to 1 in 8TCSR3 when a lower 8-bit compare match
occurs.
• TMO2 pin output control by bits OIS3, OIS2, OS1, and OS0 in 8TCSR2 is in accordance
with the 16-bit compare match conditions.
• TMIO3 pin output control by bits OIS3, OIS2, OS1, and OS0 in 8TCSR3 is in
accordance with the lower 8-bit compare match conditions.
 Setting when Input Capture Occurs
• The CMFB flag is set to 1 in 8TCSR2 and 8TCSR3 when the ICE bit is 1 in TCSR3 and
input capture occurs.
• TMIO3 pin input capture input signal edge detection is selected by bits OIS3 and OIS2 in
8TCSR2.
 Counter Clear Specification
• If counter clear on compare match has been selected by the CCLR1 and CCLR0 bits in
8TCR2, the 16-bit counter (both 8TCNT2 and 8TCNT3) is cleared.
• The settings of the CCLR1 and CCLR0 bits in 8TCR3 are ignored. The lower 8 bits
cannot be cleared independently.
 OVF Flag Operation
• The OVF flag is set to 1 in 8TCSR2 when the 16-bit counter (8TCNT2 and 8TCNT3)
overflows (from H'FFFF to H'0000).
• The OVF flag is set to 1 in 8TCSR3 when the 8-bit counter (8TCNT3) overflows (from
H'FF to H'00).
Compare Match Count Mode
• Channels 0 and 1:
When bits CKS2 to CKS0 are set to (100) in 8TCR1, 8TCNT1 counts channel 0 compare
match A events.
CMF flag setting, interrupt generation, TMO pin output, counter clearing, and so on, is in
accordance with the settings for each channel.
Note: When bit ICE = 1 in 8TCSR1, the compare match register function of TCORB0 in
channel 0 cannot be used.
Rev. 3.00 Sep 14, 2005 page 411 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
• Channels 2 and 3:
When bits CKS2 to CKS0 are set to (100) in 8TCR3, 8TCNT3 counts channel 2 compare
match A events.
CMF flag setting, interrupt generation, TMO pin output, counter clearing, and so on, is in
accordance with the settings for each channel.
Note: When bit ICE = 1 in 8TCSR3, the compare match register function of TCORB2 in
channel 2 cannot be used.
Caution
Do not set 16-bit counter mode and compare match count mode simultaneously within the same
group, as the 8TCNT input clock will not be generated and the counters will not operate.
10.4.6
Input Capture Setting
The 8TCNT value can be transferred to TCORB on detection of an input edge on the input
capture/output compare pin (TMIO1 or TMIO3). Rising edge, falling edge, or both edge detection
can be selected. In 16-bit count mode, 16-bit input capture can be used.
Setting Input Capture Operation in 8-Bit Timer Mode (Normal Operation)
• Channel 1:
 Set TCORB1 as an 8-bit input capture register with the ICE bit in 8TCSR1.
 Select rising edge, falling edge, or both edges as the input edge(s) for the input capture
signal (TMIO1) with bits OIS3 and OIS2 in 8TCSR1.
 Select the input clock with bits CKS2 to CKS0 in 8TCR1, and start the 8TCNT count.
• Channel 3:
 Set TCORB3 as an 8-bit input capture register with the ICE bit in 8TCSR3.
 Select rising edge, falling edge, or both edges as the input edge(s) for the input capture
signal (TMIO3) with bits OIS3 and OIS2 in 8TCSR3.
 Select the input clock with bits CKS2 to CKS0 in 8TCR3, and start the 8TCNT count.
Note: When TCORB1 in channel 1 is used for input capture, TCORB0 in channel 0 cannot be
used as a compare match register.
Similarly, when TCORB3 in channel 3 is used for input capture, TCORB2 in channel 2
cannot be used as a compare match register.
Rev. 3.00 Sep 14, 2005 page 412 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Setting Input Capture Operation in 16-Bit Count Mode
• Channels 0 and 1:
 In 16-bit count mode, TCORB0 and TCORB1 function as a 16-bit input capture register
when the ICE bit is set to 1 in 8TCSR1.
 Select rising edge, falling edge, or both edges as the input edge(s) for the input capture
signal (TMIO1) with bits OIS3 and OIS2 in 8TCSR0. (In 16-bit count mode, the settings
of bits OIS3 and OIS2 in 8TCSR1 are ignored.)
 Select the input clock with bits CKS2 to CKS0 in 8TCR1, and start the 8TCNT count.
• Channels 2 and 3:
 In 16-bit count mode, TCORB2 and TCORB3 function as a 16-bit input capture register
when the ICE bit is set to 1 in 8TCSR3.
 Select rising edge, falling edge, or both edges as the input edge(s) for the input capture
signal (TMIO3) with bits OIS3 and OIS2 in 8TCSR2. (In 16-bit count mode, the settings
of bits OIS3 and OIS2 in 8TCSR3 are ignored.)
 Select the input clock with bits CKS2 to CKS0 in 8TCR3, and start the 8TCNT count.
Rev. 3.00 Sep 14, 2005 page 413 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.5
Interrupt
10.5.1
Interrupt Sources
The 8-bit timer unit can generate three types of interrupt: compare match A and B (CMIA and
CMIB) and overflow (TOVI). Table 10.5 shows the interrupt sources and their priority order.
Each interrupt source is enabled or disabled by the corresponding interrupt enable bit in 8TCR. A
separate interrupt request signal is sent to the interrupt controller by each interrupt source.
Table 10.5 Types of 8-Bit Timer Interrupt Sources and Priority Order
Interrupt Source
Description
Priority
CMIA
Interrupt by CMFA
High
CMIB
Interrupt by CMFB
TOVI
Interrupt by OVF
Low
For compare match interrupts CMIA1/CMIB1 and CMIA3/CMIB3 and the overflow interrupts
(TOVI0/TOVI1 and TOVI2/TOVI3), one vector is shared by two interrupts.
Table 10.6 lists the interrupt sources.
Table 10.6 8-Bit Timer Interrupt Sources
Channel
Interrupt Source
Description
0
CMIA0
TCORA0 compare match
CMIB0
TCORB0 compare match/input capture
1
CMIA1/CMIB1
TCORA1 compare match, or TCORB1 compare match/input
capture
0, 1
TOVI0/TOVI1
Counter 0 or counter 1 overflow
2
CMIA2
TCORA2 compare match
CMIB2
TCORB2 compare match/input capture
3
CMIA3/CMIB3
TCORA3 compare match, or TCORB3 compare match/input
capture
2, 3
TOVI2/TOVI3
Counter 2 or counter 3 overflow
Rev. 3.00 Sep 14, 2005 page 414 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.5.2
A/D Converter Activation
The A/D converter can only be activated by channel 0 compare match A.
If the ADTE bit setting is 1 when the CMFA flag in 8TCSR0 is set to 1 by generation of channel
0 compare match A, an A/D conversion start request will be issued to the A/D converter. If the
TRGE bit in ADCR is 1 at this time, the A/D converter will be started. If the ADTE bit in
8TCSR0 is 1, A/D converter external trigger pin (ADTRG) input is disabled.
10.6
8-Bit Timer Application Example
Figure 10.17 shows how the 8-bit timer module can be used to output pulses with any desired
duty cycle. The settings for this example are as follows:
• Clear the CCLR1 bit to 0 and set the CCLR0 bit to 1 in 8TCR so that 8TCNT is cleared by a
TCORA compare match.
• Set bits OIS3, OIS2, OS1, and OS0 to (0110) in 8TCSR so that 1 is output on a TCORA
compare match and 0 is output on a TCORB compare match.
The above settings enable a waveform with the cycle determined by TCORA and the pulse width
detected by TCORB to be output without software intervention.
8TCNT
H'FF
Counter clear
TCORA
TCORB
H'00
TMO
Figure 10.17 Example of Pulse Output
Rev. 3.00 Sep 14, 2005 page 415 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7
Usage Notes
Note that the following kinds of contention can occur in 8-bit timer operation.
10.7.1
Contention between 8TCNT Write and Clear
If a timer counter clear signal occurs in the T3 state of a 8TCNT write cycle, clearing of the
counter takes priority and the write is not performed. Figure 10.18 shows the timing in this case.
8TCNT write cycle
T1
T2
T3
φ
Address bus
8TCNT address
Internal write signal
Counter clear signal
8TCNT
N
H'00
Figure 10.18 Contention between 8TCNT Write and Clear
Rev. 3.00 Sep 14, 2005 page 416 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7.2
Contention between 8TCNT Write and Increment
If an increment pulse occurs in the T3 state of a 8TCNT write cycle, writing takes priority and
8TCNT is not incremented. Figure 10.19 shows the timing in this case.
8TCNT write cycle
T1
T2
T3
φ
Address bus
8 TCNT address
Internal write signal
8TCNT input clock
8TCNT
N
M
8TCNT write data
Figure 10.19 Contention between 8TCNT Write and Increment
Rev. 3.00 Sep 14, 2005 page 417 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7.3
Contention between TCOR Write and Compare Match
If a compare match occurs in the T3 state of a TCOR write cycle, writing takes priority and the
compare match signal is inhibited. Figure 10.20 shows the timing in this case.
TCOR write cycle
T1
T2
T3
φ
TCOR address
Address bus
Internal write signal
8TCNT
N
TCOR
N
N+1
M
TCOR write data
Compare match signal
Figure 10.20 Contention between TCOR Write and Compare Match
Rev. 3.00 Sep 14, 2005 page 418 of 910
REJ09B0258-0300
Inhibited
Section 10 8-Bit Timers
10.7.4
Contention between TCOR Read and Input Capture
If an input capture signal occurs in the T3 state of a TCOR read cycle, the value before input
capture is read. Figure 10.21 shows the timing in this case.
TCORB read cycle
T1
T2
T3
φ
Address bus
TCORB address
Internal read signal
Input capture signal
TCORB
Internal data bus
N
M
N
Figure 10.21 Contention between TCOR Read and Input Capture
Rev. 3.00 Sep 14, 2005 page 419 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7.5
Contention between Counter Clearing by Input Capture and Counter Increment
If an input capture signal and counter increment signal occur simultaneously, counter clearing by
the input capture signal takes priority and the counter is not incremented. The value before the
counter is cleared is transferred to TCORB. Figure 10.22 shows the timing in this case.
T1
T2
T3
φ
Input capture signal
Counter clear signal
8TCNT internal clock
8TCNT
N
TCORB
X
H'00
N
Figure 10.22 Contention between Counter Clearing by Input Capture and Counter
Increment
Rev. 3.00 Sep 14, 2005 page 420 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7.6
Contention between TCOR Write and Input Capture
If an input capture signal occurs in the T3 state of a TCOR write cycle, input capture takes
priority and the write to TCOR is not performed. Figure 10.23 shows the timing in this case.
TCOR write cycle
T1
T2
T3
φ
Address bus
TCOR address
Internal write signal
Input capture signal
M
8TCNT
TCOR
X
M
Figure 10.23 Contention between TCOR Write and Input Capture
Rev. 3.00 Sep 14, 2005 page 421 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7.7
Contention between 8TCNT Byte Write and Increment in 16-Bit Count Mode
(Cascaded Connection)
If an increment pulse occurs in the T3 state of an 8TCNT byte write cycle in 16-bit count mode,
the counter write takes priority and the byte data for which the write was performed is not
incremented. The byte data for which a write was not performed is incremented. Figure 10.24
shows the timing when an increment pulse occurs in the T2 state of a byte write to 8TCNT (upper
byte). If an increment pulse occurs in the T2 state, on the other hand, the increment takes priority.
8TCNT (upper byte) byte write cycle
T1
T2
T3
φ
8TCNTH address
Address bus
Internal write signal
8TCNT input clock
8TCNT (upper byte)
N
8TCNT (lower byte)
X
N+1
8TCNT write data
X+1
Figure 10.24 Contention between 8TCNT Byte Write and Increment in 16-Bit Count Mode
Rev. 3.00 Sep 14, 2005 page 422 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
10.7.8
Contention between Compare Matches A and B
If compare matches A and B occur at the same time, the 8-bit timer operates according to the
relative priority of the output states set for compare match A and compare match B, as shown in
Table 10.7.
Table 10.7 Timer Output Priority Order
Output Setting
Priority
Toggle output
High
1 output
0 output
No change
10.7.9
Low
8TCNT Operation and Internal Clock Source Switchover
Switching internal clock sources may cause 8TCNT to increment, depending on the switchover
timing. Table 10.8 shows the relation between the time of the switchover (by writing to bits
CKS1 and CKS0) and the operation of 8TCNT.
The 8TCNT input clock is generated from the internal clock source by detecting the rising edge of
the internal clock. If a switchover is made from a low clock source to a high clock source, as in
case No. 3 in Table 10.8, the switchover will be regarded as a falling edge, a 8TCNT clock pulse
will be generated, and 8TCNT will be incremented.
8TCNT may also be incremented when switching between internal and external clocks.
Rev. 3.00 Sep 14, 2005 page 423 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Table 10.8 Internal Clock Switchover and 8TCNT Operation
No.
CKS1 and CKS0 Write
Timing
1
High → high switchover*
8TCNT Operation
1
Old clock
source
New clock
source
8TCNT clock
8TCNT
N
N+1
CKS bits rewritten
2
High → low switchover*
2
Old clock
source
New clock
source
8TCNT clock
8TCNT
N
N+1
N+2
CKS bits rewritten
3
Low → high switchover*
3
Old clock
source
New clock
source
*4
8TCNT clock
8TCNT
N
N+1
CKS bits rewritten
Rev. 3.00 Sep 14, 2005 page 424 of 910
REJ09B0258-0300
N+2
Section 10 8-Bit Timers
No.
CKS1 and CKS0 Write
Timing
4
Low → low switchover*
8TCNT Operation
4
Old clock
source
New clock
source
8TCNT clock
8TCNT
N
N+1
N+2
CKS bits rewritten
Notes: 1. Including switchovers from the high level to the halted state, and from the halted state
to the high level.
2. Including switchover from the halted state to the low level.
3. Including switchover from the low level to the halted state.
4. The switchover is regarded as a rising edge, causing 8TCNT to increment.
Rev. 3.00 Sep 14, 2005 page 425 of 910
REJ09B0258-0300
Section 10 8-Bit Timers
Rev. 3.00 Sep 14, 2005 page 426 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Section 11 Programmable Timing Pattern Controller (TPC)
11.1
Overview
The H8/3068F has a built-in programmable timing pattern controller (TPC) that provides pulse
outputs by using the 16-bit timer as a time base. The TPC pulse outputs are divided into 4-bit
groups (group 3 to group 0) that can operate simultaneously and independently.
11.1.1
Features
TPC features are listed below.
• 16-bit output data
Maximum 16-bit data can be output. TPC output can be enabled on a bit-by-bit basis.
• Four output groups
Output trigger signals can be selected in 4-bit groups to provide up to four different 4-bit
outputs.
• Selectable output trigger signals
Output trigger signals can be selected for each group from the compare match signals of three
16-bit timer channels.
• Non-overlap mode
A non-overlap margin can be provided between pulse outputs.
• Can operate together with the DMA controller (DMAC)
The compare-match signals selected as trigger signals can activate the DMAC for sequential
output of data without CPU intervention.
Rev. 3.00 Sep 14, 2005 page 427 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.1.2
Block Diagram
Figure 11.1 shows a block diagram of the TPC.
16-bit timer compare match signals
Control logic
TP 15
TP 14
TP 13
TP 12
TP 11
TP 10
TP 9
TP 8
TP 7
TP 6
TP 5
TP 4
TP 3
TP 2
TP 1
TP 0
Legend
TPMR:
TPCR:
NDERB:
NDERA:
PBDDR:
PADDR:
NDRB:
NDRA:
PBDR:
PADR:
PADDR
PBDDR
NDERA
NDERB
TPMR
TPCR
Internal
data bus
Pulse output
pins, group 3
PBDR
NDRB
PADR
NDRA
Pulse output
pins, group 2
Pulse output
pins, group 1
Pulse output
pins, group 0
TPC output mode register
TPC output control register
Next data enable register B
Next data enable register A
Port B data direction register
Port A data direction register
Next data register B
Next data register A
Port B data register
Port A data register
Figure 11.1 TPC Block Diagram
Rev. 3.00 Sep 14, 2005 page 428 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.1.3
TPC Pins
Table 11.1 summarizes the TPC output pins.
Table 11.1 TPC Pins
Name
Symbol
I/O
Function
TPC output 0
TP0
Output
Group 0 pulse output
TPC output 1
TP1
Output
TPC output 2
TP2
Output
TPC output 3
TP3
Output
TPC output 4
TP4
Output
TPC output 5
TP5
Output
TPC output 6
TP6
Output
TPC output 7
TP7
Output
TPC output 8
TP8
Output
TPC output 9
TP9
Output
TPC output 10
TP10
Output
TPC output 11
TP11
Output
TPC output 12
TP12
Output
TPC output 13
TP13
Output
TPC output 14
TP14
Output
TPC output 15
TP15
Output
Group 1 pulse output
Group 2 pulse output
Group 3 pulse output
Rev. 3.00 Sep 14, 2005 page 429 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.1.4
Registers
Table 11.2 summarizes the TPC registers.
Table 11.2 TPC Registers
Address*1
Name
Abbreviation
R/W
H'EE009
Port A data direction register
PADDR
W
Function
H'00
2
H'FFFD9
Port A data register
PADR
R/(W)*
H'00
H'EE00A
Port B data direction register
PBDDR
W
H'00
2
H'FFFDA
Port B data register
PBDR
R/(W)*
H'00
H'FFFA0
TPC output mode register
TPMR
R/W
H'F0
H'FFFA1
TPC output control register
TPCR
R/W
H'FF
H'FFFA2
Next data enable register B
NDERB
R/W
H'00
H'FFFA3
Next data enable register A
NDERA
R/W
H'00
H'FFFA5/
H'FFFA7*3
Next data register A
NDRA
R/W
H'00
H'FFFA4/
3
H'FFFA6*
Next data register B
NDRB
R/W
H'00
Notes: 1. Lower 20 bits of the address in advanced mode.
2. Bits used for TPC output cannot be written.
3. The NDRA address is H'FFFA5 when the same output trigger is selected for TPC
output groups 0 and 1 by settings in TPCR. When the output triggers are different, the
NDRA address is H'FFFA7 for group 0 and H'FFFA5 for group 1. Similarly, the address
of NDRB is H'FFFA4 when the same output trigger is selected for TPC output groups 2
and 3 by settings in TPCR. When the output triggers are different, the NDRB address
is H'FFFA6 for group 2 and H'FFFA4 for group 3.
Rev. 3.00 Sep 14, 2005 page 430 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.2
Register Descriptions
11.2.1
Port A Data Direction Register (PADDR)
PADDR is an 8-bit write-only register that selects input or output for each pin in port A.
Bit
7
6
5
4
3
2
1
0
PA7 DDR PA6 DDR PA5 DDR PA4 DDR PA3 DDR PA2 DDR PA1 DDR PA0 DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port A data direction 7 to 0
These bits select input or
output for port A pins
Port A is multiplexed with pins TP7 to TP0. Bits corresponding to pins used for TPC output must
be set to 1. For further information about PADDR, see section 8.11, Port A.
11.2.2
Port A Data Register (PADR)
PADR is an 8-bit readable/writable register that stores TPC output data for groups 0 and 1, when
these TPC output groups are used.
Bit
7
6
5
4
3
2
1
0
PA 7
PA 6
PA 5
PA 4
PA 3
PA 2
PA 1
PA 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
Port A data 7 to 0
These bits store output data
for TPC output groups 0 and 1
Note: * Bits selected for TPC output by NDERA settings become read-only bits.
For further information about PADR, see section 8.11, Port A.
Rev. 3.00 Sep 14, 2005 page 431 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.3
Port B Data Direction Register (PBDDR)
PBDDR is an 8-bit write-only register that selects input or output for each pin in port B.
Bit
7
6
5
4
3
2
1
0
PB7DDR PB6DDR PB5DDR PB4DDR PB3DDR PB2DDR PB1DDR PB0DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port B direction 7 to 0
These bits select input or
output for port B pins
Port B is multiplexed with pins TP15 to TP8. Bits corresponding to pins used for TPC output must
be set to 1. For further information about PBDDR, see section 8.12, Port B.
11.2.4
Port B Data Register (PBDR)
PBDR is an 8-bit readable/writable register that stores TPC output data for groups 2 and 3, when
these TPC output groups are used.
Bit
7
PB7
6
5
4
3
2
1
0
PB6
PB5
PB4
PB3
PB2
PB1
PB0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
Port B data 7 to 0
These bits store output data
for TPC output groups 2 and 3
Note: * Bits selected for TPC output by NDERB settings become read-only bits.
For further information about PBDR, see section 8.12, Port B.
Rev. 3.00 Sep 14, 2005 page 432 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.5
Next Data Register A (NDRA)
NDRA is an 8-bit readable/writable register that stores the next output data for TPC output
groups 1 and 0 (pins TP7 to TP0). During TPC output, when an 16-bit timer compare match event
specified in TPCR occurs, NDRA contents are transferred to the corresponding bits in PADR.
The address of NDRA differs depending on whether TPC output groups 0 and 1 have the same
output trigger or different output triggers.
NDRA is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Same Trigger for TPC Output Groups 0 and 1: If TPC output groups 0 and 1 are triggered by
the same compare match event, the NDRA address is H'FFFA5. The upper 4 bits belong to group
1 and the lower 4 bits to group 0. Address H'FFFA7 consists entirely of reserved bits that cannot
be modified and always read 1.
Address H'FFFA5
Bit
6
7
NDR7
NDR6
5
NDR5
4
NDR4
2
3
NDR3
NDR2
1
NDR1
0
NDR0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Next data 7 to 4
These bits store the next output
data for TPC output group 1
Next data 3 to 0
These bits store the next output
data for TPC output group 0
Address H'FFFA7
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
Initial value
1
1
1
1
1
1
1
1
Read/Write
—
—
—
—
—
—
—
—
Reserved bits
Rev. 3.00 Sep 14, 2005 page 433 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Different Triggers for TPC Output Groups 0 and 1: If TPC output groups 0 and 1 are
triggered by different compare match events, the address of the upper 4 bits of NDRA (group 1)
is H'FFFA5 and the address of the lower 4 bits (group 0) is H'FFFA7. Bits 3 to 0 of address
H'FFFA5 and bits 7 to 4 of address H'FFFA7 are reserved bits that cannot be modified and always
read 1.
Address H'FFFA5
Bit
7
6
5
4
3
2
1
0
NDR7
NDR6
NDR5
NDR4
—
—
—
—
Initial value
0
0
0
0
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
—
—
—
—
Next data 7 to 4
These bits store the next output
data for TPC output group 1
Reserved bits
Address H'FFFA7
Bit
7
6
5
4
3
2
1
0
—
—
—
—
NDR3
NDR2
NDR1
NDR0
Initial value
1
1
1
1
0
0
0
0
Read/Write
—
—
—
—
R/W
R/W
R/W
R/W
Reserved bits
Rev. 3.00 Sep 14, 2005 page 434 of 910
REJ09B0258-0300
Next data 3 to 0
These bits store the next output
data for TPC output group 0
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.6
Next Data Register B (NDRB)
NDRB is an 8-bit readable/writable register that stores the next output data for TPC output
groups 3 and 2 (pins TP15 to TP8). During TPC output, when an 16-bit timer compare match event
specified in TPCR occurs, NDRB contents are transferred to the corresponding bits in PBDR.
The address of NDRB differs depending on whether TPC output groups 2 and 3 have the same
output trigger or different output triggers.
NDRB is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Same Trigger for TPC Output Groups 2 and 3: If TPC output groups 2 and 3 are triggered by
the same compare match event, the NDRB address is H'FFFA4. The upper 4 bits belong to group
3 and the lower 4 bits to group 2. Address H'FFFA6 consists entirely of reserved bits that cannot
be modified and always read 1.
Address H'FFFA4
Bit
7
6
5
4
3
2
1
0
NDR15
NDR14
NDR13
NDR12
NDR11
NDR10
NDR9
NDR8
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Next data 15 to 12
These bits store the next output
data for TPC output group 3
Next data 11 to 8
These bits store the next output
data for TPC output group 2
Address H'FFFA6
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
Initial value
1
1
1
1
1
1
1
1
Read/Write
—
—
—
—
—
—
—
—
Reserved bits
Rev. 3.00 Sep 14, 2005 page 435 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Different Triggers for TPC Output Groups 2 and 3: If TPC output groups 2 and 3 are
triggered by different compare match events, the address of the upper 4 bits of NDRB (group 3) is
H'FFFA4 and the address of the lower 4 bits (group 2) is H'FFFA6. Bits 3 to 0 of address
H'FFFA4 and bits 7 to 4 of address H'FFFA6 are reserved bits that cannot be modified and always
read 1.
Address H'FFFA4
Bit
7
6
5
4
3
2
1
0
NDR15
NDR14
NDR13
NDR12
—
—
—
—
Initial value
0
0
0
0
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
—
—
—
—
Next data 15 to 12
These bits store the next output
data for TPC output group 3
Reserved bits
Address H'FFFA6
Bit
7
6
5
4
3
2
1
0
—
—
—
—
NDR11
NDR10
NDR9
NDR8
Initial value
1
1
1
1
0
0
0
0
Read/Write
—
—
—
—
R/W
R/W
R/W
R/W
Reserved bits
Rev. 3.00 Sep 14, 2005 page 436 of 910
REJ09B0258-0300
Next data 11 to 8
These bits store the next output
data for TPC output group 2
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.7
Next Data Enable Register A (NDERA)
NDERA is an 8-bit readable/writable register that enables or disables TPC output groups 1 and 0
(TP7 to TP0) on a bit-by-bit basis.
Bit
6
7
NDER7
4
5
NDER6 NDER5
3
NDER4 NDER3
2
NDER2
1
0
NDER1 NDER0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Next data enable 7 to 0
These bits enable or disable
TPC output groups 1 and 0
If a bit is enabled for TPC output by NDERA, then when the 16-bit timer compare match event
selected in the TPC output control register (TPCR) occurs, the NDRA value is automatically
transferred to the corresponding PADR bit, updating the output value. If TPC output is disabled,
the bit value is not transferred from NDRA to PADR and the output value does not change.
NDERA is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 0—Next Data Enable 7 to 0 (NDER7 to NDER0): These bits enable or disable TPC
output groups 1 and 0 (TP7 to TP0) on a bit-by-bit basis.
Bits 7 to 0
NDER7 to NDER0
Description
0
TPC outputs TP7 to TP0 are disabled
(NDR7 to NDR0 are not transferred to PA7 to PA0)
1
TPC outputs TP7 to TP0 are enabled
(NDR7 to NDR0 are transferred to PA7 to PA0)
(Initial value)
Rev. 3.00 Sep 14, 2005 page 437 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.8 Next Data Enable Register B (NDERB)
NDERB is an 8-bit readable/writable register that enables or disables TPC output groups 3 and 2
(TP15 to TP8) on a bit-by-bit basis.
Bit
7
6
4
5
3
2
1
0
NDER15 NDER14 NDER13 NDER12 NDER11 NDER10 NDER9 NDER8
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Next data enable 15 to 8
These bits enable or disable
TPC output groups 3 and 2
If a bit is enabled for TPC output by NDERB, then when the 16-bit timer compare match event
selected in the TPC output control register (TPCR) occurs, the NDRB value is automatically
transferred to the corresponding PBDR bit, updating the output value. If TPC output is disabled,
the bit value is not transferred from NDRB to PBDR and the output value does not change.
NDERB is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 0—Next Data Enable 15 to 8 (NDER15 to NDER8): These bits enable or disable TPC
output groups 3 and 2 (TP15 to TP8) on a bit-by-bit basis.
Bits 7 to 0
NDER15 to NDER8
Description
0
TPC outputs TP15 to TP8 are disabled
(NDR15 to NDR8 are not transferred to PB7 to PB0)
1
TPC outputs TP15 to TP8 are enabled
(NDR15 to NDR8 are transferred to PB7 to PB0)
Rev. 3.00 Sep 14, 2005 page 438 of 910
REJ09B0258-0300
(Initial value)
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.9
TPC Output Control Register (TPCR)
TPCR is an 8-bit readable/writable register that selects output trigger signals for TPC outputs on a
group-by-group basis.
Bit
7
6
5
4
3
2
1
0
G3CMS1 G3CMS0 G2CMS1 G2CMS0 G1CMS1 G1CMS0 G0CMS1 G0CMS0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Group 3 compare
match select 1 and 0
These bits select
the compare match
Group 2 compare
event that triggers
match select 1 and 0
TPC output group 3
These bits select
(TP15 to TP12)
the compare match
Group 1 compare
event that triggers
TPC output group 2 match select 1 and 0
These bits select
(TP11 to TP8)
the compare match
Group 0 compare
event that triggers
match select 1 and 0
TPC output group 1
These bits select
(TP7 to TP4)
the compare match
event that triggers
TPC output group 0
(TP3 to TP0)
TPCR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Rev. 3.00 Sep 14, 2005 page 439 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Bits 7 and 6—Group 3 Compare Match Select 1 and 0 (G3CMS1, G3CMS0): These bits
select the compare match event that triggers TPC output group 3 (TP15 to TP12).
Bit 7
G3CMS1
Bit 6
G3CMS0
0
0
TPC output group 3 (TP15 to TP12) is triggered by compare match in 16bit timer channel 0
1
TPC output group 3 (TP15 to TP12) is triggered by compare match in 16bit timer channel 1
0
TPC output group 3 (TP15 to TP12) is triggered by compare match in 16bit timer channel 2
1
TPC output group 3 (TP15 to TP12) is triggered by
compare match in 16-bit timer channel 2
1
Description
(Initial value)
Bits 5 and 4—Group 2 Compare Match Select 1 and 0 (G2CMS1, G2CMS0): These bits
select the compare match event that triggers TPC output group 2 (TP11 to TP8).
Bit 5
G2CMS1
Bit 4
G2CMS0
0
0
TPC output group 2 (TP11 to TP8) is triggered by compare match in 16-bit
timer channel 0
1
TPC output group 2 (TP11 to TP8) is triggered by compare match in 16-bit
timer channel 1
0
TPC output group 2 (TP11 to TP8) is triggered by compare match in 16-bit
timer channel 2
1
TPC output group 2 (TP11 to TP8) is triggered by
compare match in 16-bit timer channel 2
1
Description
Rev. 3.00 Sep 14, 2005 page 440 of 910
REJ09B0258-0300
(Initial value)
Section 11 Programmable Timing Pattern Controller (TPC)
Bits 3 and 2—Group 1 Compare Match Select 1 and 0 (G1CMS1, G1CMS0): These bits
select the compare match event that triggers TPC output group 1 (TP7 to TP4).
Bit 3
G1CMS1
Bit 2
G1CMS0
0
0
TPC output group 1 (TP7 to TP4) is triggered by compare match in 16-bit
timer channel 0
1
TPC output group 1 (TP7 to TP4) is triggered by compare match in 16-bit
timer channel 1
0
TPC output group 1 (TP7 to TP4) is triggered by compare match in 16-bit
timer channel 2
1
TPC output group 1 (TP7 to TP4) is triggered by
compare match in 16-bit timer channel 2
1
Description
(Initial value)
Bits 1 and 0—Group 0 Compare Match Select 1 and 0 (G0CMS1, G0CMS0): These bits
select the compare match event that triggers TPC output group 0 (TP3 to TP0).
Bit 1
G0CMS1
Bit 0
G0CMS0
0
0
TPC output group 0 (TP3 to TP0) is triggered by compare match in 16-bit
timer channel 0
1
TPC output group 0 (TP3 to TP0) is triggered by compare match in 16-bit
timer channel 1
0
TPC output group 0 (TP3 to TP0) is triggered by compare match in 16-bit
timer channel 2
1
TPC output group 0 (TP3 to TP0) is triggered by
compare match in 16-bit timer channel 2
1
Description
(Initial value)
Rev. 3.00 Sep 14, 2005 page 441 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.2.10 TPC Output Mode Register (TPMR)
TPMR is an 8-bit readable/writable register that selects normal or non-overlapping TPC output
for each group.
Bit
7
6
5
4
—
—
—
—
Initial value
1
1
1
1
0
0
0
0
Read/Write
—
—
—
—
R/W
R/W
R/W
R/W
3
2
G3NOV G2NOV
1
0
G1NOV G0NOV
Reserved bits
Group 3 non-overlap
Selects non-overlapping TPC
output for group 3 (TP15 to TP12 )
Group 2 non-overlap
Selects non-overlapping TPC
output for group 2 (TP11 to TP8 )
Group 1 non-overlap
Selects non-overlapping TPC
output for group 1 (TP7 to TP4 )
Group 0 non-overlap
Selects non-overlapping TPC
output for group 0 (TP3 to TP0 )
The output trigger period of a non-overlapping TPC output waveform is set in general register B
(GRB) in the 16-bit timer channel selected for output triggering. The non-overlap margin is set in
general register A (GRA). The output values change at compare match A and B. For details see
section 11.3.4, Non-Overlapping TPC Output.
TPMR is initialized to H'F0 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 4—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 442 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Bit 3—Group 3 Non-Overlap (G3NOV): Selects normal or non-overlapping TPC output for
group 3 (TP15 to TP12).
Bit 3
G3NOV
Description
0
Normal TPC output in group 3 (output values change at
compare match A in the selected 16-bit timer channel)
1
Non-overlapping TPC output in group 3 (independent 1 and 0 output at
compare match A and B in the selected 16-bit timer channel)
(Initial value)
Bit 2—Group 2 Non-Overlap (G2NOV): Selects normal or non-overlapping TPC output for
group 2 (TP11 to TP8).
Bit 2
G2NOV
Description
0
Normal TPC output in group 2 (output values change at
compare match A in the selected 16-bit timer channel)
1
Non-overlapping TPC output in group 2 (independent 1 and 0 output at
compare match A and B in the selected 16-bit timer channel)
(Initial value)
Bit 1—Group 1 Non-Overlap (G1NOV): Selects normal or non-overlapping TPC output for
group 1 (TP7 to TP4).
Bit 1
G1NOV
Description
0
Normal TPC output in group 1 (output values change at
compare match A in the selected 16-bit timer channel)
1
Non-overlapping TPC output in group 1 (independent 1 and 0 output at
compare match A and B in the selected 16-bit timer channel)
(Initial value)
Bit 0—Group 0 Non-Overlap (G0NOV): Selects normal or non-overlapping TPC output for
group 0 (TP3 to TP0).
Bit 0
G0NOV
Description
0
Normal TPC output in group 0 (output values change at
compare match A in the selected 16-bit timer channel)
1
Non-overlapping TPC output in group 0 (independent 1 and 0 output at
compare match A and B in the selected 16-bit timer channel)
(Initial value)
Rev. 3.00 Sep 14, 2005 page 443 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.3
Operation
11.3.1
Overview
When corresponding bits in PADDR or PBDDR and NDERA or NDERB are set to 1, TPC output
is enabled. The TPC output initially consists of the corresponding PADR or PBDR contents.
When a compare-match event selected in TPCR occurs, the corresponding NDRA or NDRB bit
contents are transferred to PADR or PBDR to update the output values.
Figure 11.2 illustrates the TPC output operation. Table 11.3 summarizes the TPC operating
conditions.
DDR
NDER
Q
Q
Output trigger signal
C
Q
DR
D
Q NDR
D
Internal
data bus
TPC output pin
Figure 11.2 TPC Output Operation
Table 11.3 TPC Operating Conditions
NDER
DDR
Pin Function
0
0
Generic input port
1
Generic output port
0
Generic input port (but the DR bit is a read-only bit, and when compare
match occurs, the NDR bit value is transferred to the DR bit)
1
TPC pulse output
1
Sequential output of up to 16-bit patterns is possible by writing new output data to NDRA and
NDRB before the next compare match. For information on non-overlapping operation, see
section 11.3.4, Non-Overlapping TPC Output.
Rev. 3.00 Sep 14, 2005 page 444 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.3.2
Output Timing
If TPC output is enabled, NDRA/NDRB contents are transferred to PADR/PBDR and output
when the selected compare match event occurs. Figure 11.3 shows the timing of these operations
for the case of normal output in groups 2 and 3, triggered by compare match A.
φ
N
TCNT
N+1
N
GRA
Compare
match A signal
n
NDRB
PBDR
m
n
TP8 to TP15
m
n
Figure 11.3 Timing of Transfer of Next Data Register Contents and Output (Example)
Rev. 3.00 Sep 14, 2005 page 445 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.3.3
Normal TPC Output
Sample Setup Procedure for Normal TPC Output: Figure 11.4 shows a sample procedure for
setting up normal TPC output.
Normal TPC output
16-bit timer
setup
Port and
TPC setup
16-bit timer
setup
Select GR functions
1
Set GRA value
2
Select counting operation
3
Select interrupt request
4
Set initial output data
5
Select port output
6
Enable TPC output
7
Select TPC output trigger
8
Set next TPC output data
9
Start counter
10
Compare match?
1.
Set TIOR to make GRA an output compare
register (with output inhibited).
2. Set the TPC output trigger period.
3. Select the counter clock source with bits
TPSC2 to TPSC0 in TCR. Select the counter
clear source with bits CCLR1 and CCLR0.
4. Enable the IMFA interrupt in TIER.
The DMAC can also be set up to transfer
data to the next data register.
5. Set the initial output values in the DR bits
of the input/output port pins to be used for
TPC output.
6. Set the DDR bits of the input/output port
pins to be used for TPC output to 1.
7. Set the NDER bits of the pins to be used for
TPC output to 1.
8. Select the 16-bit timer compare match event
to be used as the TPC output trigger in TPCR.
9. Set the next TPC output values in the NDR bits.
10. Set the STR bit to 1 in TSTR to start the
timer counter.
11. At each IMFA interrupt, set the next output
values in the NDR bits.
No
Yes
Set next TPC output data
11
Figure 11.4 Setup Procedure for Normal TPC Output (Example)
Rev. 3.00 Sep 14, 2005 page 446 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Example of Normal TPC Output (Example of Five-Phase Pulse Output): Figure 11.5 shows
an example in which the TPC is used for cyclic five-phase pulse output.
TCNT value
Compare match
TCNT
GRA
H'0000
Time
NDRB
80
PBDR
00
C0
80
40
C0
60
40
20
60
30
20
10
30
18
10
08
18
88
08
80
88
C0
80
40
C0
TP15
TP14
TP13
TP12
TP11
•
•
•
•
The 16-bit timer channel to be used as the output trigger channel is set up so that GRA is an output
compare register and the counter will be cleared by compare match A. The trigger period is set in GRA.
The IMIEA bit is set to 1 in TIER to enable the compare match A interrupt.
H'F8 is written in PBDDR and NDERB, and bits G3CMS1, G3CMS0, G2CMS1, and G2CMS0 are set in
TPCR to select compare match in the 16-bit timer channel set up in step 1 as the output trigger.
Output data H'80 is written in NDRB.
The timer counter in this 16-bit timer channel is started. When compare match A occurs, the NDRB
contents are transferred to PBDR and output. The compare match/input capture A (IMFA) interrupt
service routine writes the next output data (H'C0) in NDRB.
Five-phase overlapping pulse output (one or two phases active at a time) can be obtained by writing
H'40, H'60, H'20, H'30, H'10, H'18, H'08, H'88… at successive IMFA interrupts. If the DMAC is set for
activation by this interrupt, pulse output can be obtained without loading the CPU.
Figure 11.5 Normal TPC Output Example (Five-Phase Pulse Output)
Rev. 3.00 Sep 14, 2005 page 447 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.3.4
Non-Overlapping TPC Output
Sample Setup Procedure for Non-Overlapping TPC Output: Figure 11.6 shows a sample
procedure for setting up non-overlapping TPC output.
Non-overlapping
TPC output
16-bit timer
setup
Port and
TPC setup
16-bit timer
setup
Select GR functions
1
Set GR values
2
Select counting operation
3
Select interrupt requests
4
Set initial output data
5
Set up TPC output
6
Enable TPC transfer
7
Select TPC transfer trigger
8
Select non-overlapping groups
9
Set next TPC output data
10
Start counter
11
Compare match A?
1. Set TIOR to make GRA and GRB output
compare registers (with output inhibited).
2. Set the TPC output trigger period in GRB
and the non-overlap margin in GRA.
3. Select the counter clock source with bits
TPSC2 to TPSC0 in TCR. Select the counter
clear source with bits CCLR1 and CCLR0.
4. Enable the IMFA interrupt in TISRA.
The DMAC can also be set up to transfer
data to the next data register.
5. Set the initial output values in the DR bits
of the input/output port pins to be used for
TPC output.
6. Set the DDR bits of the input/output port pins
to be used for TPC output to 1.
7. Set the NDER bits of the pins to be used for
TPC output to 1.
8. In TPCR, select the 16-bit timer compare match
event to be used as the TPC output trigger.
9. In TPMR, select the groups that will operate
in non-overlap mode.
10. Set the next TPC output values in the NDR
bits.
11. Set the STR bit to 1 in TSTR to start the timer
counter.
12. At each IMFA interrupt, write the next output
value in the NDR bits.
No
Yes
Set next TPC output data
12
Figure 11.6 Setup Procedure for Non-Overlapping TPC Output (Example)
Rev. 3.00 Sep 14, 2005 page 448 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Example of Non-Overlapping TPC Output (Example of Four-Phase Complementary NonOverlapping Output): Figure 11.7 shows an example of the use of TPC output for four-phase
complementary non-overlapping pulse output.
TCNT value
GRB
TCNT
GRA
H'0000
Time
NDRB
95
PBDR
00
65
95
59
05
65
56
41
59
95
50
56
65
14
95
05
65
Non-overlap margin
TP15
TP14
TP13
TP12
TP11
TP10
TP9
TP8
• The 16-bit timer channel to be used as the output trigger channel is set up so that GRA and GRB are
output compare registers and the counter will be cleared by compare match B. The TPC output trigger
period is set in GRB. The non-overlap margin is set in GRA. The IMIEA bit is set to 1 in TISRA to enable
IMFA interrupts.
• H'FF is written in PBDDR and NDERB, and bits G3CMS1, G3CMS0, G2CMS1, and G2CMS0 are set in
TPCR to select compare match in the 16-bit timer channel set up in step 1 as the output trigger. Bits
G3NOV and G2NOV are set to 1 in TPMR to select non-overlapping output. Output data H'95 is written in
NDRB.
• The timer counter in this 16-bit timer channel is started. When compare match B occurs, outputs change
from 1 to 0. When compare match A occurs, outputs change from 0 to 1 (the change from 0 to 1 is delayed
by the value of GRA). The IMFA interrupt service routine writes the next output data (H'65) in NDRB.
• Four-phase complementary non-overlapping pulse output can be obtained by writing H'59, H'56, H'95…
at successive IMFA interrupts. If the DMAC is set for activation by this interrupt, pulse output can be
obtained without loading the CPU.
Figure 11.7 Non-Overlapping TPC Output Example (Four-Phase Complementary
Non-Overlapping Pulse Output)
Rev. 3.00 Sep 14, 2005 page 449 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.3.5
TPC Output Triggering by Input Capture
TPC output can be triggered by 16-bit timer input capture as well as by compare match. If GRA
functions as an input capture register in the 16-bit timer channel selected in TPCR, TPC output
will be triggered by the input capture signal. Figure 11.8 shows the timing.
φ
TIOC pin
Input capture
signal
N
NDR
M
DR
N
Figure 11.8 TPC Output Triggering by Input Capture (Example)
Rev. 3.00 Sep 14, 2005 page 450 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
11.4
Usage Notes
11.4.1
Operation of TPC Output Pins
TP0 to TP15 are multiplexed with 16-bit timer, DMAC, address bus, and other pin functions.
When 16-bit timer, DMAC, or address output is enabled, the corresponding pins cannot be used
for TPC output. The data transfer from NDR bits to DR bits takes place, however, regardless of
the usage of the pin.
Pin functions should be changed only under conditions in which the output trigger event will not
occur.
11.4.2
Note on Non-Overlapping Output
During non-overlapping operation, the transfer of NDR bit values to DR bits takes place as
follows.
1. NDR bits are always transferred to DR bits at compare match A.
2. At compare match B, NDR bits are transferred only if their value is 0. Bits are not transferred
if their value is 1.
Figure 11.9 illustrates the non-overlapping TPC output operation.
DDR
NDER
Q
Q
Compare match A
Compare match B
C
Q
DR
D
Q NDR
D
TPC output pin
Figure 11.9 Non-Overlapping TPC Output
Rev. 3.00 Sep 14, 2005 page 451 of 910
REJ09B0258-0300
Section 11 Programmable Timing Pattern Controller (TPC)
Therefore, 0 data can be transferred ahead of 1 data by making compare match B occur before
compare match A. NDR contents should not be altered during the interval from compare match B
to compare match A (the non-overlap margin).
This can be accomplished by having the IMFA interrupt service routine write the next data in
NDR, or by having the IMFA interrupt activate the DMAC. The next data must be written before
the next compare match B occurs.
Figure 11.10 shows the timing relationships.
Compare
match A
Compare
match B
NDR write
NDR write
NDR
DR
0 output
0/1 output
0 output
Write to NDR
in this interval
Do not write
to NDR in this
interval
0/1 output
Write to NDR
in this interval
Do not write
to NDR in this
interval
Figure 11.10 Non-Overlapping Operation and NDR Write Timing
Rev. 3.00 Sep 14, 2005 page 452 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
Section 12 Watchdog Timer
12.1
Overview
The H8/3068F has an on-chip watchdog timer (WDT). The WDT has two selectable functions: it
can operate as a watchdog timer to supervise system operation, or it can operate as an interval
timer. As a watchdog timer, it generates a reset signal for the H8/3068F chip if a system crash
allows the timer counter (TCNT) to overflow before being rewritten. In interval timer operation,
an interval timer interrupt is requested at each TCNT overflow.
12.1.1
Features
WDT features are listed below.
• Selection of eight counter clock sources
φ/2, φ /32, φ /64, φ /128, φ /256, φ /512, φ /2048, or φ /4096
• Interval timer option
• Timer counter overflow generates a reset signal or interrupt.
The reset signal is generated in watchdog timer operation. An interval timer interrupt is
generated in interval timer operation.
• Watchdog timer reset signal resets the entire H8/3068F internally.
The reset signal generated by timer counter overflow during watchdog timer operation resets
the entire H8/3068F internally.
Rev. 3.00 Sep 14, 2005 page 453 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.1.2
Block Diagram
Figure 12.1 shows a block diagram of the WDT.
Overflow
TCNT
Interrupt signal
(interval timer)
Interrupt
control
TCSR
Reset control
Internal
data bus
Internal clock sources
φ/2
RSTCSR
Reset
(internal, external)
Read/
write
control
φ/32
φ/64
Clock
Clock
selector
φ/128
φ/256
φ/512
Legend
TCNT:
Timer counter
TCSR:
Timer control/status register
RSTCSR: Reset control/status register
φ/2048
φ/4096
Figure 12.1 WDT Block Diagram
12.1.3
Register Configuration
Table 12.1 summarizes the WDT registers.
Table 12.1 WDT Registers
Address*1
Write*2
Read
Name
H'FFF8C H'FFF8C Timer control/status register
H'FFF8D Timer counter
H'FFF8E H'FFF8F Reset control/status register
Abbreviation
R/W
TCSR
R/(W)*3 H'18
TCNT
R/W
RSTCSR
Notes: 1. Lower 20 bits of the address in advanced mode.
2. Write word data starting at this address.
3. Only 0 can be written in bit 7, to clear the flag.
Rev. 3.00 Sep 14, 2005 page 454 of 910
REJ09B0258-0300
Initial Value
H'00
R/(W)*
3
H'3F
Section 12 Watchdog Timer
12.2
Register Descriptions
12.2.1
Timer Counter (TCNT)
TCNT is an 8-bit readable and writable up-counter.
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Note: TCNT is write-protected by a password. For details see section 12.2.4, Notes on Register
Access.
When the TME bit is set to 1 in TCSR, TCNT starts counting pulses generated from an internal
clock source selected by bits CKS2 to CKS0 in TCSR. When the count overflows (changes from
H'FF to H'00), the OVF bit is set to 1 in TCSR. TCNT is initialized to H'00 by a reset and when
the TME bit is cleared to 0.
Rev. 3.00 Sep 14, 2005 page 455 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.2.2
Timer Control/Status Register (TCSR)
TCSR is an 8-bit readable and writable register. Its functions include selecting the timer mode
and clock source.
Bit
7
6
5
4
3
2
1
0
OVF
WT/IT
TME
—
—
CKS2
CKS1
CKS0
Initial value
0
0
0
1
1
0
0
0
Read/Write
R/(W)*
R/W
R/W
—
—
R/W
R/W
R/W
Clock select
These bits select the
TCNT clock source
Reserved bits
Timer enable
Selects whether TCNT runs or halts
Timer mode select
Selects the mode
Overflow flag
Status flag indicating overflow
Notes: TCSR is write-protected by a password. For details see section 12.2.4, Notes on Register
Access.
* Only 0 can be written, to clear the flag.
Bits 7 to 5 are initialized to 0 by a reset and in standby mode. Bits 2 to 0 are initialized to 0 by a
reset. In software standby mode bits 2 to 0 are not initialized, but retain their previous values.
Rev. 3.00 Sep 14, 2005 page 456 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
Bit 7—Overflow Flag (OVF): This status flag indicates that the timer counter has overflowed
from H'FF to H'00.
Bit 7
OVF
0
1
Description
[Clearing condition]
Cleared by reading OVF when OVF = 1, then writing 0 in OVF
(Initial value)
[Setting condition]
Set when TCNT changes from H'FF to H'00
Bit 6—Timer Mode Select (WT/IT): Selects whether to use the WDT as a watchdog timer or
interval timer. If used as an interval timer, the WDT generates an interval timer interrupt request
when TCNT overflows. If used as a watchdog timer, the WDT generates a reset signal when
TCNT overflows.
Bit 6
WT/IT
Description
0
Interval timer: requests interval timer interrupts
1
Watchdog timer: generates a reset signal
(Initial value)
Bit 5—Timer Enable (TME): Selects whether TCNT runs or is halted. When WT/IT = 1, clear
the software standby bit (SSBY) to 0 in SYSCR before setting TME. When setting SSBY to 1,
TME should be cleared to 0.
Bit 5
TME
Description
0
TCNT is initialized to H'00 and halted
1
TCNT is counting
(Initial value)
Bits 4 and 3—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 457 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
Bits 2 to 0—Clock Select 2 to 0 (CKS2/1/0): These bits select one of eight internal clock
sources, obtained by prescaling the system clock (φ), for input to TCNT.
Bit 2
CKS2
Bit 1
CKS1
Bit 0
CKS0
Description
0
0
0
φ/2
1
φ /32
0
φ /64
1
φ /128
0
φ /256
1
φ /512
0
φ /2048
1
φ /4096
1
1
0
1
12.2.3
(Initial value)
Reset Control/Status Register (RSTCSR)
RSTCSR is an 8-bit readable and writable register that indicates when a reset signal has been
generated by watchdog timer overflow, and controls external output of the reset signal.
Bit
7
6
5
4
3
2
1
0
WRST
—
—
—
—
—
—
—
Initial value
0
0
1
1
1
1
1
1
Read/Write
R/(W)*
R/W
—
—
—
—
—
—
Reserved bits
Watchdog timer reset
Indicates that a reset signal has been generated
Notes: RSTCSR is write-protected by a password. For details see section 12.2.4, Notes on
Register Access.
* Only 0 can be written in bit 7, to clear the flag.
Bits 7 and 6 are initialized by input of a reset signal at the RES pin. They are not initialized by
reset signals generated by watchdog timer overflow.
Rev. 3.00 Sep 14, 2005 page 458 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
Bit 7—Watchdog Timer Reset (WRST): During watchdog timer operation, this bit indicates
that TCNT has overflowed and generated a reset signal. This reset signal resets the entire
H8/3068F chip internally.
Bit 7
WRST
0
1
Description
[Clearing condition]
Reset signal at RES pin.
Read WRST when WRST =1, then write 0 in WRST.
(Initial value)
[Setting condition]
Set when TCNT overflow generates a reset signal during watchdog timer operation
Bit 6—Reserved
Bits 5 to 0—Reserved: These bits cannot be modified and are always read as 1.
12.2.4
Notes on Register Access
The watchdog timer’s TCNT, TCSR, and RSTCSR registers differ from other registers in being
more difficult to write. The procedures for writing and reading these registers are given below.
Writing to TCNT and TCSR: These registers must be written by a word transfer instruction.
They cannot be written by byte instructions. Figure 12.2 shows the format of data written to
TCNT and TCSR. TCNT and TCSR both have the same write address. The write data must be
contained in the lower byte of the written word. The upper byte must contain H'5A (password for
TCNT) or H'A5 (password for TCSR). This transfers the write data from the lower byte to TCNT
or TCSR.
15
TCNT write
Address
H'FFF8C*
H'5A
H'FFF8C*
0
Write data
15
TCSR write
Address
8 7
8 7
H'A5
0
Write data
Note: * Lower 20 bits of the address in advanced mode.
Figure 12.2 Format of Data Written to TCNT and TCSR
Rev. 3.00 Sep 14, 2005 page 459 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
Writing to RSTCSR: RSTCSR must be written by a word transfer instruction. It cannot be
written by byte transfer instructions. Figure 12.3 shows the format of data written to RSTCSR. To
write 0 in the WRST bit, the write data must have H'A5 in the upper byte and H'00 in the lower
byte. The data (H'00) in the lower byte is written to RSTCSR, clearing the WRST bit to 0. To
write to the RSTOE bit, the upper byte must contain H'5A and the lower byte must contain the
write data. Writing this word transfers a write data value into the RSTOE bit.
Writing 0 in WRST bit
Address
H'FFF8E*
Writing to RSTOE bit
Address
15
8 7
H'A5
15
H'FFF8E*
0
H'00
8 7
H'5A
0
Write data
Note: * Lower 20 bits of the address in advanced mode.
Figure 12.3 Format of Data Written to RSTCSR
Reading TCNT, TCSR, and RSTCSR: These registers are read like other registers. Reading
TCNT, TCSR, and RSTCSR: These registers are read like other registers. Byte transfer
instructions can be used. The read addresses are H'FFF8C for TCSR, H'FFF8D for TCNT, and
H'FFF8F for RSTCSR, as listed in table 12.2.
Table 12.2 Read Addresses of TCNT, TCSR, and RSTCSR
Address*
Register
H'FFF8C
TCSR
H'FFF8D
TCNT
H'FFF8F
RSTCSR
Note: * Lower 20 bits of the address in advanced mode.
Rev. 3.00 Sep 14, 2005 page 460 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.3
Operation
Operations when the WDT is used as a watchdog timer and as an interval timer are described
below.
12.3.1
Watchdog Timer Operation
Figure 12.4 illustrates watchdog timer operation. To use the WDT as a watchdog timer, set the
WT/IT and TME bits to 1 in TCSR. Software must prevent TCNT overflow by rewriting the
TCNT value (normally by writing H'00) before overflow occurs. If TCNT fails to be rewritten and
overflows due to a system crash etc., the H8/3068F is internally reset for a duration of 518 states.
A watchdog reset has the same vector as a reset generated by input at the RES pin. Software can
distinguish a RES reset from a watchdog reset by checking the WRST bit in RSTCSR.
If a RES reset and a watchdog reset occur simultaneously, the RES reset takes priority.
WDT overflow
H'FF
TME set to 1
TCNT count
value
H'00
OVF = 1
Start
Internal
reset signal
H'00 written
in TCNT
Reset
H'00 written
in TCNT
518 states
Figure 12.4 Operation in Watchdog Timer Mode
Rev. 3.00 Sep 14, 2005 page 461 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.3.2
Interval Timer Operation
Figure 12.5 illustrates interval timer operation. To use the WDT as an interval timer, clear bit
WT/IT to 0 and set bit TME to 1 in TCSR. An interval timer interrupt request is generated at each
TCNT overflow. This function can be used to generate interval timer interrupts at regular
intervals.
H'FF
TCNT
count value
Time t
H'00
WT/ IT = 0
TME = 1
Interval
timer
interrupt
Interval
timer
interrupt
Interval
timer
interrupt
Interval
timer
interrupt
Figure 12.5 Interval Timer Operation
Rev. 3.00 Sep 14, 2005 page 462 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.3.3
Timing of Setting of Overflow Flag (OVF)
Figure 12.6 shows the timing of setting of the OVF flag. The OVF flag is set to 1 when TCNT
overflows. At the same time, a reset signal is generated in watchdog timer operation, or an
interval timer interrupt is generated in interval timer operation.
φ
TCNT
H'FF
H'00
Overflow signal
OVF
Figure 12.6 Timing of Setting of OVF
Rev. 3.00 Sep 14, 2005 page 463 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.3.4
Timing of Setting of Watchdog Timer Reset Bit (WRST)
The WRST bit in RSTCSR is valid when bits WT/IT and TME are both set to 1 in TCSR.
Figure 12.7 shows the timing of setting of WRST and the internal reset timing. The WRST bit is
set to 1 when TCNT overflows and OVF is set to 1. At the same time an internal reset signal is
generated for the entire H8/3068F chip. This internal reset signal clears OVF to 0, but the WRST
bit remains set to 1. The reset routine must therefore clear the WRST bit.
φ
H'FF
TCNT
H'00
Overflow signal
OVF
WDT internal
reset
WRST
Figure 12.7 Timing of Setting of WRST Bit and Internal Reset
Rev. 3.00 Sep 14, 2005 page 464 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
12.4
Interrupts
During interval timer operation, an overflow generates an interval timer interrupt (WOVI). The
interval timer interrupt is requested whenever the OVF bit is set to 1 in TCSR.
12.5
Usage Notes
Contention between TCNT Write and Increment: If a timer counter clock pulse is generated
during the T3 state of a write cycle to TCNT, the write takes priority and the timer count is not
incremented. See figure 12.8.
CPU: TCNT write cycle
T1
T2
T3
φ
TCNT
Internal write
signal
TCNT input
clock
TCNT
N
M
Counter write data
Figure 12.8 Contention between TCNT Write and Count up
Changing CKS2 to CKS0 Bit: Halt TCNT by clearing the TME bit to 0 in TCSR before
changing the values of bits CKS2 to CKS0.
Rev. 3.00 Sep 14, 2005 page 465 of 910
REJ09B0258-0300
Section 12 Watchdog Timer
Rev. 3.00 Sep 14, 2005 page 466 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Section 13 Serial Communication Interface
13.1
Overview
The H8/3068F has a serial communication interface (SCI) with three independent channels. All
three channels have identical functions. The SCI can communicate in both asynchronous and
synchronous mode. It also has a multiprocessor communication function for serial
communication among two or more processors.
When the SCI is not used, it can be halted to conserve power. Each SCI channel can be halted
independently. For details, see section 20.6, Module Standby Function.
The SCI also has a smart card interface function conforming to the ISO/IEC 7816-3
(Identification Card) standard. This function supports serial communication with a smart card.
Switching between the normal serial communication interface and the smart card interface is
carried out by means of a register setting.
13.1.1
Features
SCI features are listed below.
• Selection of synchronous or asynchronous mode for serial communication
Asynchronous mode
Serial data communication is synchronized one channel at a time. The SCI can communicate
with a universal asynchronous receiver/transmitter (UART), asynchronous communication
interface adapter (ACIA), or other chip that employs standard asynchronous communication.
It can also communicate with two or more other processors using the multiprocessor
communication function. There are twelve selectable serial data transfer formats.
 Data length:
7 or 8 bits
 Stop bit length:
1 or 2 bits
 Parity:
even/odd/none
 Multiprocessor bit:
1 or 0
 Receive error detection: parity, overrun, and framing errors
 Break detection:
by reading the RxD level directly when a framing error occurs
Rev. 3.00 Sep 14, 2005 page 467 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Synchronous mode
Serial data communication is synchronized with a clock signal. The SCI can communicate
with other chips having a synchronous communication function.
There is a single serial data communication format.
 Data length:
8 bits
 Receive error detection:
overrun errors
• Full-duplex communication
The transmitting and receiving sections are independent, so the SCI can transmit and receive
simultaneously. The transmitting and receiving sections are both double-buffered, so serial
data can be transmitted and received continuously.
• The following settings can be made for the serial data to be transferred:
 LSB-first or MSB-first transfer
 Inversion of data logic level
• Built-in baud rate generator with selectable bit rates
• Selectable transmit/receive clock sources: internal clock from baud rate generator, or external
clock from the SCK pin
• Four types of interrupts
Transmit-data-empty, transmit-end, receive-data-full, and receive-error interrupts are
requested independently. The transmit-data-empty and receive-data-full interrupts from SCI0
can activate the DMA controller (DMAC) to transfer data.
Features of the smart card interface are listed below.
• Asynchronous communication
 Data length: 8 bits
 Parity bits generated and checked
 Error signal output in receive mode (parity error)
 Error signal detect and automatic data retransmit in transmit mode
 Supports both direct convention and inverse convention
• Built-in baud rate generator with selectable bit rates
• Three types of interrupts
Transmit-data-empty, receive-data-full, and transmit/receive-error interrupts are requested
independently. The transmit-data-empty and receive-data-full interrupts can activate the
DMA controller (DMAC) to transfer data.
Rev. 3.00 Sep 14, 2005 page 468 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.1.2
Block Diagram
Bus interface
Figure 13.1 shows a block diagram of the SCI.
Module data bus
RDR
TDR
SSR
BRR
SCR
RxD
TxD
RSR
TSR
φ
SMR
Baud rate
generator
SCMR
Transmit/receive
control
Parity generate
Parity check
SCK
Internal data bus
φ/ 4
φ/16
φ/64
Clock
External clock
TEI
TXI
RXI
ERI
Legend
RSR : Receive shift register
RDR : Receive data register
TSR : Transmit shift register
TDR : Transmit data register
SMR : Serial mode register
SCR : Serial control register
SSR : Serial status register
BRR : Bit rate register
SCMR : Smart card mode register
Figure 13.1 SCI Block Diagram
Rev. 3.00 Sep 14, 2005 page 469 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.1.3
Input/Output Pins
The SCI has serial pins for each channel as listed in table 13.1.
Table 13.1 SCI Pins
Channel Name
Abbreviation
I/O
Function
0
SCK0
Input/output
SCI0 clock input/output
Receive data pin
RxD0
Input
SCI0 receive data input
Transmit data pin
TxD0
Output
SCI0 transmit data output
Serial clock pin
SCK1
Input/output
SCI1 clock input/output
Receive data pin
RxD1
Input
SCI1 receive data input
Transmit data pin
TxD1
Output
SCI1 transmit data output
Serial clock pin
SCK2
Input/output
SCI2 clock input/output
Receive data pin
RxD2
Input
SCI2 receive data input
Transmit data pin
TxD2
Output
SCI2 transmit data output
1
2
Serial clock pin
Rev. 3.00 Sep 14, 2005 page 470 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.1.4
Register Configuration
The SCI has internal registers as listed in table 13.2. These registers select asynchronous or
synchronous mode, specify the data format and bit rate, control the transmitter and receiver
sections, and specify switching between the serial communication interface and smart card
interface.
Table 13.2 SCI Registers
Channel
Address*1
Name
Abbreviation
R/W
Initial Value
0
H’FFFB0
Serial mode register
SMR
R/W
H'00
H’FFFB1
Bit rate register
BRR
R/W
H'FF
H’FFFB2
Serial control register
SCR
R/W
H'00
H’FFFB3
Transmit data register
TDR
R/W
1
2
H'FF
2
H’FFFB4
Serial status register
SSR
R/(W)* H'84
H’FFFB5
Receive data register
RDR
R
H'00
H’FFFB6
Smart card mode register
SCMR
R/W
H'F2
H’FFFB8
Serial mode register
SMR
R/W
H'00
H’FFFB9
Bit rate register
BRR
R/W
H'FF
H’FFFBA
Serial control register
SCR
R/W
H'00
H’FFFBB
Transmit data register
TDR
R/W
H'FF
2
H’FFFBC
Serial status register
SSR
R/(W)* H'84
H’FFFBD
Receive data register
RDR
R
H'00
H’FFFBE
Smart card mode register
SCMR
R/W
H'F2
H’FFFC0
Serial mode register
SMR
R/W
H'00
H’FFFC1
Bit rate register
BRR
R/W
H'FF
H’FFFC2
Serial control register
SCR
R/W
H'00
H’FFFC3
Transmit data register
TDR
R/W
H'FF
2
H’FFFC4
Serial status register
SSR
R/(W)* H'84
H’FFFC5
Receive data register
RDR
R
H'00
H’FFFC6
Smart card mode register
SCMR
R/W
H'F2
Notes: 1. Indicates the lower 20 bits of the address in advanced mode.
2. Only 0 can be written, to clear flags.
Rev. 3.00 Sep 14, 2005 page 471 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.2
Register Descriptions
13.2.1
Receive Shift Register (RSR)
RSR is the register that receives serial data.
7
Bit
5
6
4
3
2
1
0
Read/Write
The SCI loads serial data input at the RxD pin into RSR in the order received, LSB (bit 0) first,
thereby converting the data to parallel data. When one byte of data has been received, it is
automatically transferred to RDR. The CPU cannot read or write RSR directly.
13.2.2
Receive Data Register (RDR)
RDR is the register that stores received serial data.
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
When the SCI has received one byte of serial data, it transfers the received data from RSR into
RDR for storage, completing the receive operation. RSR is then ready to receive the next data.
This double-buffering allows data to be received continuously.
RDR is a read-only register. Its contents cannot be modified by the CPU. RDR is initialized to
H'00 by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 472 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.2.3
Transmit Shift Register (TSR)
TSR is the register that transmits serial data.
Bit
7
6
5
4
3
2
1
0
Read/Write
The SCI loads transmit data from TDR to TSR, then transmits the data serially from the TxD pin,
LSB (bit 0) first. After transmitting one data byte, the SCI automatically loads the next transmit
data from TDR into TSR and starts transmitting it. If the TDRE flag is set to 1 in SSR, however,
the SCI does not load the TDR contents into TSR. The CPU cannot read or write RSR directly.
13.2.4
Transmit Data Register (TDR)
TDR is an 8-bit register that stores data for serial transmission.
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
When the SCI detects that TSR is empty, it moves transmit data written in TDR from TDR into
TSR and starts serial transmission. Continuous serial transmission is possible by writing the next
transmit data in TDR during serial transmission from TSR.
The CPU can always read and write TDR. TDR is initialized to H'FF by a reset and in standby
mode.
Rev. 3.00 Sep 14, 2005 page 473 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.2.5
Serial Mode Register (SMR)
SMR is an 8-bit register that specifies the SCI's serial communication format and selects the
clock source for the baud rate generator.
7
6
5
4
3
2
1
0
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Clock select 1/0
These bits select the
baud rate generator's
clock source
Multiprocessor mode
Selects the multiprocessor
function
Stop bit length
Selects the stop bit length
Parity mode
Selects even or odd parity
Parity enable
Enables or disables the addition of a parity bit
Character length
Selects character length in asynchronous mode
Communication mode
Selects asynchronous or synchronous mode
The CPU can always read and write SMR. SMR is initialized to H'00 by a reset and in standby
mode.
Rev. 3.00 Sep 14, 2005 page 474 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 7—Communication Mode (C/A)/GSM Mode (GM): The function of this bit differs for the
normal serial communication interface and for the smart card interface. Its function is switched
with the SMIF bit in SCMR.
For serial communication interface (SMIF bit in SCMR cleared to 0): Selects whether the
SCI operates in asynchronous or synchronous mode.
Bit 7
C/A
Description
0
Asynchronous mode
1
Synchronous mode
(Initial value)
For smart card interface (SMIF bit in SCMR set to 1): Selects GSM mode for the smart card
interface.
Bit 7
GM
Description
0
The TEND flag is set 12.5 etu after the start bit
1
The TEND flag is set 11.0 etu after the start bit
(Initial value)
Note: etu (Elementary time unit: the time for transfer of one bit)
Bit 6—Character Length (CHR): Selects 7-bit or 8-bits data length in asynchronous mode. In
synchronous mode, the data length is 8 bits regardless of the CHR setting,
Bit 6
CHR
Description
0
8-bit data
1
7-bit data*
(Initial value)
Note: * When 7-bit data is selected, the MSB (bit 7) of TDR is not transmitted.
Rev. 3.00 Sep 14, 2005 page 475 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 5—Parity Enable (PE): In asynchronous mode, this bit enables or disables the addition of a
parity bit to transmit data, and the checking of the parity bit in receive data. In synchronous
mode, the parity bit is neither added nor checked, regardless of the PE bit setting.
Bit 5
PE
Description
0
Parity bit not added or checked
1
Parity bit added and checked*
(Initial value)
Note: * When PE bit is set to 1, an even or odd parity bit is added to transmit data according to the
even or odd parity mode selection by the O/E bit, and the parity bit in receive data is
checked to see that it matches the even or odd mode selected by the O/E bit.
Bit 4—Parity Mode (O/E): Selects even or odd parity. The O/E bit setting is only valid when
the PE bit is set to 1, enabling parity bit addition and checking, in asynchronous mode. The O/E
bit setting is ignored in synchronous mode, or when parity addition and checking is disabled in
asynchronous mode.
Bit 4
O/E
Description
0
Even parity*1
1
(Initial value)
2
Odd parity*
Notes: 1. When even parity is selected, the parity bit added to transmit data makes an even
number of 1s in the transmitted character and parity bit combined. Receive data must
have an even number of 1s in the received character and parity bit combined.
2. When odd parity is selected, the parity bit added to transmit data makes an odd
number of 1s in the transmitted character and parity bit combined. Receive data must
have an odd number of 1s in the received character and parity bit combined.
Bit 3—Stop Bit Length (STOP): Selects one or two stop bits in asynchronous mode. This
setting is used only in asynchronous mode. In synchronous mod no stop bit is added, so the
STOP bit setting is ignored.
Bit 3
STOP
Description
0
1 stop bit*1
1
(Initial value)
2
2 stop bits*
Notes: 1. One stop bit (with value 1) is added to the end of each transmitted character.
2. Two stop bits (with value 1) are added to the end of each transmitted character.
Rev. 3.00 Sep 14, 2005 page 476 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
In receiving, only the first stop bit is checked, regardless of the STOP bit setting. If the second
stop bit is 1, it is treated as a stop bit. If the second stop bit is 0, it is treated as the start bit of the
next incoming character.
Bit 2—Multiprocessor Mode (MP): Selects a multiprocessor format. When a multiprocessor
format is selected, parity settings made by the PE and O/E bits are ignored. The MP bit setting is
valid only in asynchronous mode. It is ignored in synchronous mode.
For further information on the multiprocessor communication function, see section 13.3.3,
Multiprocessor Communication.
Bit 2
MP
Description
0
Multiprocessor function disabled
1
Multiprocessor format selected
(Initial value)
Bits 1 and 0—Clock Select 1 and 0 (CKS1/0): These bits select the clock source for the on-chip
baud rate generator. Four clock sources are available: φ, φ/4, φ/16, and φ/64.
For the relationship between the clock source, bit rate register setting, and baud rate, see section
13.2.8, Bit Rate Register (BRR).
Bit 1
CKS1
Bit 0
CKS0
Description
0
0
φ
0
1
φ/4
1
0
φ/16
1
1
φ/64
(Initial value)
Rev. 3.00 Sep 14, 2005 page 477 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.2.6
Serial Control Register (SCR)
SCR register enables or disables the SCI transmitter and receiver, enables or disables serial clock
output in asynchronous mode, enables or disables interrupts, and selects the transmit/receive
clock source.
Bit
7
6
5
4
3
2
1
0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
0
0
0
0
R/W
R/W
R/W
R/W
Initial value
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
Clock enable 1/0
hese bits select the
SCI clock source
Transmit-end interrupt enable
Enables or disables transmit-end
interrupts (TEI)
Multiprocessor interrupt enable
Enables or disables multiprocessor
interrupts
Receive enable
Enables or disables the receiver
Transmit enable
Enables or disables the transmitter
Receive interrupt enable
Enables or disables receive-data-full interrupts (RXI) and
receive-error interrupts (ERI)
Transmit interrupt enable
Enables or disables transmit-data-empty interrupts (TXI)
The CPU can always read and write SCR. SCR is initialized to H'00 by a reset and in standby
mode.
Rev. 3.00 Sep 14, 2005 page 478 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 7—Transmit Interrupt Enable (TIE): Enables or disables the transmit-data-empty interrupt
(TXI) requested when the TDRE flag in SSR is set to 1 due to transfer of serial transmit data from
TDR to TSR.
Bit 7
TIE
Description
0
Transmit-data-empty interrupt request (TXI) is disabled*
1
Transmit-data-empty interrupt request (TXI) is enabled
(Initial value)
Note: * TXI interrupt requests can be cleared by reading the value 1 from the TDRE flag, then
clearing it to 0; or by clearing the TIE bit to 0.
Bit 6—Receive Interrupt Enable (RIE): Enables or disables the receive-data-full interrupt
(RXI) requested when the RDRF flag in SSR is set to 1 due to transfer of serial receive data from
RSR to RDR; also enables or disables the receive-error interrupt (ERI).
Bit 6
RIE
Description
0
Receive-data-full (RXI) and receive-error (ERI) interrupt requests are
disabled*
(Initial value)
1
Receive-data-full (RXI) and receive-error (ERI) interrupt requests are enabled
Note: * RXI and ERI interrupt requests can be cleared by reading the value 1 from the RDRF, FER,
PER, or ORER flag, then clearing the flag to 0; or by clearing the RIE bit to 0.
Bit 5—Transmit Enable (TE): Enables or disables the start of SCI serial transmitting
operations.
Bit 5
TE
Description
0
Transmitting disabled*1
1
2
(Initial value)
Transmitting enabled*
Notes: 1. The TDRE flag is fixed at 1 in SSR.
2. In the enabled state, serial transmission starts when the TDRE flag in SSR is cleared
to 0 after writing of transmit data into TDR. Select the transmit format in SMR before
setting the TE bit to 1.
Rev. 3.00 Sep 14, 2005 page 479 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 4—Receive Enable (RE): Enables or disables the start of SCI serial receiving operations.
Bit 4
RE
Description
0
Receiving disabled*
1
2
1
(Initial value)
Receiving enabled*
Notes: 1. Clearing the RE bit to 0 does not affect the RDRF, FER, PER, and ORER flags. These
flags retain their previous values.
2. In the enabled state, serial receiving starts when a start bit is detected in asynchronous
mode, or serial clock input is detected in synchronous mode. Select the receive format
in SMR before setting the RE bit to 1.
Bit 3—Multiprocessor Interrupt Enable (MPIE): Enables or disables multiprocessor
interrupts. The MPIE bit setting is valid only in asynchronous mode, and only if the MP bit is set
to 1 in SMR. The MPIE bit setting is ignored in synchronous mode or when the MP bit is cleared
to 0.
Bit 3
MPIE
Description
0
Multiprocessor interrupts are disabled (normal receive operation)(Initial value)
Clearing conditions
(1) The MPIE bit is cleared to 0
(2) MPB = 1 in received data
1
Multiprocessor interrupts are enabled*
Receive-data-full interrupts (RXI), receive-error interrupts (ERI), and setting of
the RDRF, FER, and ORER status flags in SSR are disabled until data with the
multiprocessor bit set to 1 is received.
Note: * The SCI does not transfer receive data from RSR to RDR, does not detect receive errors,
and does not set the RDRF, FER, and ORER flags in SSR. When it receives data in which
MPB = 1, the SCI sets the MPB bit to 1 in SSR, automatically clears the MPIE bit to 0,
enables RXI and ERI interrupts (if the TIE and RIE bits in SCR are set to 1), and allows the
FER and ORER flags to be set.
Rev. 3.00 Sep 14, 2005 page 480 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 2—Transmit-End interrupt Enable (TEIE): Enables or disables the transmit-end interrupt
(TEI) requested if TDR does not contain valid transmit data when the MSB is transmitted.
Bit 2
TEIE
Description
0
Transmit-end interrupt requests (TEI) are disabled*
1
Transmit-end interrupt requests (TEI) are enabled*
(Initial value)
Note: * TEI interrupt requests can be cleared by reading the value 1 from the TDRE flag in SSR,
then clearing the TDRE flag to 0, thereby also clearing the TEND flag to 0; or by clearing
the TEIE bit to 0.
Bits 1 and 0—Clock Enable 1 and 0 (CKE1/0): The function of these bits differs for the normal
serial communication interface and for the smart card interface. Their function is switched with
the SMIF bit in SCMR.
For serial communication interface (SMIF bit in SCMR cleared to 0): These bits select the
SCI clock source and enable or disable clock output from the SCK pin. Depending on the settings
of CKE1 and CKE0, the SCK pin can be used for generic input/output, serial clock output, or
serial clock input.
The CKE0 setting is valid only in asynchronous mode, and only when the SCI is internally
clocked (CKE1 = 0). The CKE0 setting is ignored in synchronous mode, or when an external
clock source is selected (CKE1 = 1). Select the SCI operating mode in SMR before setting the
CKE1 and CKE0 bits . For further details on selection of the SCI clock source, see table 13.9 in
section 13.3, Operation.
Bit 1 Bit 0
CKE1 CKE0 Description
0
0
0
1
1
0
1
1
Asynchronous mode
Internal clock, SCK pin available for generic input/output*1
Synchronous mode
Internal clock, SCK pin used for serial clock output*1
Asynchronous mode
Internal clock, SCK pin used for clock output*2
Synchronous mode
Internal clock, SCK pin used for serial clock output
Asynchronous mode
External clock, SCK pin used for clock input*3
Synchronous mode
External clock, SCK pin used for serial clock input
Asynchronous mode
External clock, SCK pin used for clock input*3
Synchronous mode
External clock, SCK pin used for serial clock input
Notes: 1. Initial value
2. The output clock frequency is the same as the bit rate.
3. The input clock frequency is 16 times the bit rate.
Rev. 3.00 Sep 14, 2005 page 481 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
For smart card interface (SMIF bit in SCMR set to 1): These bits, together with the GM bit in
SMR, determine whether the SCK pin is used for generic input/output or as the serial clock output
pin.
SMR
GM
Bit 1 Bit 0
CKE1 CKE0 Description
0
0
0
SCK pin available for generic input/output
0
0
1
SCK pin used for clock output
1
0
0
SCK pin output fixed low
1
0
1
SCK pin used for clock output
1
1
0
SCK pin output fixed high
1
1
1
SCK pin used for clock output
Rev. 3.00 Sep 14, 2005 page 482 of 910
REJ09B0258-0300
(Initial value)
Section 13 Serial Communication Interface
13.2.7
Serial Status Register (SSR)
SSR is an 8-bit register containing multiprocessor bit values, and status flags that indicate the
operating status of the SCI.
Bit
Initial value
Read/Write
5
7
6
TDRE
RDRF
1
0
R/(W)*1
4
ORER FER/ERS
0
R/(W)*1
0
R/(W)*1
3
2
1
0
PER
TEND
MPB
MPBT
1
0
0
R
R
R/W
0
R/(W)*1
R/(W)
*1
Multiprocessor bit
transfer
Value of multiprocessor
bit to be transmitted
Multiprocessor bit
Stores the received
multiprocessor bit value
Transmit end*2
Status flag indicating end of
transmission
Parity error
Status flag indicating detection
of a receive parity error
Framing error (FER)/Error signal status (ERS)*2
Status flag indicating detection of a receive framing
error, or flag indicating detection of an error signal
Overrun error
Status flag indicating detection
of a receive overrun error
Receive data register full
Status flag indicating that data has been received
and stored in RDR
Transmit data register empty
Status flag indicating that transmit data has been transferred from
TDR into TSR and new data can be written in TDR
Notes: 1. Only 0 can be written, to clear the flag.
2. Function differs between the normal serial communication interface and the smart card interface.
Rev. 3.00 Sep 14, 2005 page 483 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
The CPU can always read and write SSR, but cannot write 1 in the TDRE, RDRF, ORER, PER,
and FER flags. These flags can be cleared to 0 only if they have first been read while set to 1.
The TEND and MPB flags are read-only bits that cannot be written.
SSR is initialized to H'84 by a reset and in standby mode.
Bit 7—Transmit Data Register Empty (TDRE): Indicates that the SCI has loaded transmit data
from TDR into TSR and the next serial data can be written in TDR.
Bit 7
TDRE
Description
0
TDR contains valid transmit data
Clearing conditions
Read TDRE when TDRE = 1, then write 0 in TDRE
The DMAC writes data in TDR
1
TDR does not contain valid transmit data
(Initial value)
Setting conditions
The chip is reset or enters standby mode
The TE bit in SCR is cleared to 0
TDR contents are loaded into TSR, so new data can be written in TDR
Bit 6—Receive Data Register Full (RDRF): Indicates that RDR contains new receive data.
Bit 6
RDRF
Description
0
RDR does not contain new receive data
Clearing conditions
The chip is reset or enters standby mode
Read RDRF when RDRF = 1, then write 0 in RDRF
The DMAC reads data from RDR
(Initial value)
1
RDR contains new receive data
Setting condition
Serial data is received normally and transferred from RSR to RDR
Note: The RDR contents and the RDRF flag are not affected by detection of receive errors or by
clearing of the RE bit to 0 in SCR. They retain their previous values. If the RDRF flag is
still set to 1 when reception of the next data ends, an overrun error will occur and the
receive data will be lost.
Rev. 3.00 Sep 14, 2005 page 484 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 5—Overrun Error (ORER): Indicates that data reception ended abnormally due to an
overrun error.
Bit 5
ORER
Description
0
Receiving is in progress or has ended normally*1
Clearing conditions
The chip is reset or enters standby mode
Read ORER when ORER = 1, then write 0 in ORER
1
A receive overrun error occurred*2
Setting condition
Reception of the next serial data ends when RDRF = 1
(Initial value)
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the ORER flag, which retains its
previous value.
2. RDR continues to hold the receive data prior to the overrun error, so subsequent
receive data is lost. Serial receiving cannot continue while the ORER flag is set to 1.
In synchronous mode, serial transmitting is also disabled.
Bit 4—Framing Error (FER)/Error Signal Status (ERS): The function of this bit differs for
the normal serial communication interface and for the smart card interface. Its function is
switched with the SMIF bit in SCMR.
For serial communication interface (SMIF bit in SCMR cleared to 0): Indicates that data
reception ended abnormally due to a framing error in asynchronous mode.
Bit 4
FER
Description
0
Receiving is in progress or has ended normally*1
Clearing conditions
The chip is reset or enters standby mode
Read FER when FER = 1, then write 0 in FER
1
A receive framing error occurred*2
Setting condition
The stop bit at the end of the receive data is checked and found to be 0
(Initial value)
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the FER flag, which retains its previous
value.
2. When the stop bit length is 2 bits, only the first bit is checked. The second stop bit is
not checked. When a framing error occurs the SCI transfers the receive data into RDR
but does not set the RDRF flag. Serial receiving cannot continue while the FER flag is
set to 1. In synchronous mode, serial transmitting is also disabled.
Rev. 3.00 Sep 14, 2005 page 485 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
For smart card interface (SMIF bit in SCMR set to 1): Indicates the status of the error signal
sent back from the receiving side during transmission. Framing errors are not detected in smart
card interface mode.
Bit 4
ERS
Description
0
Normal reception, no error signal*
Clearing conditions
The chip is reset or enters standby mode
Read ERS when ERS = 1, then write 0 in ERS
(Initial value)
1
An error signal has been sent from the receiving side indicating detection of a
parity error
Setting condition
The error signal is low when sampled
Note: * Clearing the TE bit to 0 in SCR does not affect the ERS flag, which retains its previous
value.
Bit 3—Parity Error (PER): Indicates that data reception ended abnormally due to a parity error
in asynchronous mode.
Bit 3
PER
Description
0
Receiving is in progress or has ended normally*1
Clearing conditions
The chip is reset or enters standby mode
Read PER when PER = 1, then write 0 in PER
1
A receive parity error occurred*2
Setting condition
The number of 1s in receive data, including the parity bit, does not match the
even or odd parity setting of O/E in SMR
(Initial value)
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the PER flag, which retains its previous
value.
2. When a parity error occurs the SCI transfers the receive data into RDR but does not
set the RDRF flag. Serial receiving cannot continue while the PER flag is set to 1. In
synchronous mode, serial transmitting is also disabled.
Rev. 3.00 Sep 14, 2005 page 486 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 2—Transmit End (TEND): The function of this bit differs for the normal serial
communication interface and for the smart card interface. Its function is switched with the SMIF
bit in SCMR.
For serial communication interface (SMIF bit in SCMR cleared to 0): Indicates that when
the last bit of a serial character was transmitted TDR did not contain valid transmit data, so
transmission has ended. The TEND flag is a read-only bit and cannot be written.
Bit 2
TEND
Description
0
Transmission is in progress
Clearing conditions
Read TDRE when TDRE = 1, then write 0 in TDRE
The DMAC writes data in TDR
1
End of transmission
(Initial value)
Setting conditions
The chip is reset or enters standby mode
The TE bit in SCR is cleared to 0
TDRE is 1 when the last bit of a 1-byte serial transmit character is transmitted
For smart card interface (SMIF bit in SCMR set to 1): Indicates that when the last bit of a
serial character was transmitted TDR did not contain valid transmit data, so transmission has
ended. The TEND flag is a read-only bit and cannot be written.
Bit 2
TEND
Description
0
Transmission is in progress
Clearing conditions
Read TDRE when TDRE = 1, then write 0 in TDRE
The DMAC writes data in TDR
1
End of transmission
(Initial value)
Setting conditions
The chip is reset or enters standby mode
The TE bit is cleared to 0 in SCR and the FER/ERS bit is also cleared to 0
TDRE is 1 and FER/ERS is 0 (normal transmission) 2.5 etu (when GM = 0) or
1.0 etu (when GM = 1) after a 1-byte serial character is transmitted
Note: etu (Elementary time unit: the time for transfer of one bit)
Rev. 3.00 Sep 14, 2005 page 487 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Bit 1—Multiprocessor bit (MPB): Stores the value of the multiprocessor bit in the receive data
when a multiprocessor format is used in asynchronous mode. MPB is a read-only bit, and cannot
be written.
Bit 1
MPB
Description
0
Multiprocessor bit value in receive data is 0*
1
Multiprocessor bit value in receive data is 1
(Initial value)
Note: * If the RE bit in SCR is cleared to 0 when a multiprocessor format is selected, MPB retains
its previous value.
Bit 0—Multiprocessor Bit Transfer (MPBT): Stores the value of the multiprocessor bit added
to transmit data when a multiprocessor format in selected for transmitting in asynchronous mode.
The MPBT bit setting is ignored in synchronous mode, when a multiprocessor format is not
selected, or when the SCI cannot transmit.
Bit 1
MPBT
Description
0
Multiprocessor bit value in transmit data is 0
1
Multiprocessor bit value in transmit data is 1
13.2.8
(Initial value)
Bit Rate Register (BRR)
BRR is an 8-bit register that., together with the CKS1 and CKS0 bits in SMR that select the baud
rate generator clock source, determines the serial communication bit rate.
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The CPU can always read and write BRR. BRR is initialized to H'FF by a reset and in standby
mode. Each SCI channel has independent baud rate generator control, so different values can be
set in the three channels.
Table 13.3 shows examples of BRR settings in asynchronous mode. Table 13.4 shows examples
of BRR settings in synchronous mode.
Rev. 3.00 Sep 14, 2005 page 488 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Table 13.3 Examples of Bit Rates and BRR Settings in Asynchronous Mode
φ (MHz)
Bit Rate
(bit/s)
n
2
2.097152
N
110
1
141 0.03
1
148 –0.04
1
174 –0.26
1
212 0.03
150
1
103 0.16
1
108 0.21
1
127 0.00
1
155 0.16
300
0
207 0.16
0
217 0.21
0
255 0.00
1
77
600
0
103 0.16
0
108 0.21
0
127 0.00
0
155 0.16
1200
0
51
0.16
0
54
–0.70
0
63
0.00
0
77
0.16
2400
0
25
0.16
0
26
1.14
0
31
0.00
0
38
0.16
4800
0
12
0.16
0
13
–2.48
0
15
0.00
0
19
–2.34
9600
0
6
–6.99
0
6
–2.48
0
7
0.00
0
9
–2.34
19200
0
2
8.51
0
2
13.78
0
3
0.00
0
4
–2.34
31250
0
1
0.00
0
1
4.86
0
1
22.88
0
2
0.00
38400
0
1
–18.62
0
1
–14.67
0
1
0.00
—
—
—
Error (%) n
N
2.4576
Error (%) n
N
3
Error (%) n
N
Error (%)
0.16
φ (MHz)
Bit Rate
(bit/s)
n
3.6864
4
4.9152
5
N
Error (%) n
N
Error (%) n
N
Error (%) n
N
Error (%)
110
2
64
0.70
2
70
0.03
2
86
0.31
2
88
–0.25
150
1
191 0.00
1
207 0.16
1
255 0.00
2
64
0.16
300
1
95
0.00
1
103 0.16
1
127 0.00
1
129 0.16
600
0
191 0.00
0
207 0.16
0
255 0.00
1
64
1200
0
95
0.00
0
103 0.16
0
127 0.00
0
129 0.16
2400
0
47
0.00
0
51
0.16
0
63
0.00
0
64
0.16
4800
0
23
0.00
0
25
0.16
0
31
0.00
0
32
–1.36
9600
0
11
0.00
0
12
0.16
0
15
0.00
0
15
1.73
19200
0
5
0.00
0
6
–6.99
0
7
0.00
0
7
1.73
31250
—
—
—
0
3
0.00
0
4
–1.70
0
4
0.00
38400
0
2
0.00
0
2
8.51
0
3
0.00
0
3
1.73
0.16
Rev. 3.00 Sep 14, 2005 page 489 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
φ (MHz)
Bit Rate
(bit/s)
n
6
6.144
N
110
2
106 –0.44
2
108 0.08
2
130 –0.07
2
141 0.03
150
2
77
0.16
2
79
0.00
2
95
0.00
2
103 0.16
Error (%) n
N
7.3728
Error (%) n
N
8
Error (%) n
N
Error (%)
300
1
155 0.16
1
159 0.00
1
191 0.00
1
207 0.16
600
1
77
0.16
1
79
0.00
1
95
0.00
1
103 0.16
1200
0
155 0.16
0
159 0.00
0
191 0.00
0
207 0.16
2400
0
77
0.16
0
79
0.00
0
95
0.00
0
103 0.16
4800
0
38
0.16
0
39
0.00
0
47
0.00
0
51
0.16
9600
0
19
–2.34
0
19
0.00
0
23
0.00
0
25
0.16
19200
0
9
–2.34
0
9
0.00
0
11
0.00
0
12
0.16
31250
0
5
0.00
0
5
2.40
0
6
5.33
0
7
0.00
38400
0
4
–2.34
0
4
0.00
0
5
0.00
0
6
–6.99
φ (MHz)
Bit Rate
(bit/s)
9.8304
n
N
110
2
174 –0.26
10
Error (%) n
2
N
12
Error (%) n
N
12.288
Error (%) n
177 –0.25
2
212 0.03
2
N
Error (%)
217 0.08
150
2
127 0.00
2
129 0.16
2
155 0.16
2
159 0.00
300
1
255 0.00
2
64
0.16
2
77
0.16
2
79
600
1
127 0.00
1
129 0.16
1
155 0.16
1
159 0.00
1200
0
255 0.00
1
64
0.16
1
77
0.16
1
79
2400
0
127 0.00
0
129 0.16
0
155 0.16
0
159 0.00
4800
0
63
0
64
0.16
0
77
0
79
0.00
0.16
0.00
0.00
0.00
9600
0
31
0.00
0
32
–1.36
0
38
0.16
0
39
0.00
19200
0
15
0.00
0
15
1.73
0
19
–2.34
0
19
0.00
31250
0
9
–1.70
0
9
0.00
0
11
0.00
0
11
2.40
38400
0
7
0.00
0
7
1.73
0
9
–2.34
0
9
0.00
Rev. 3.00 Sep 14, 2005 page 490 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
φ (MHz)
Bit
Rate
(bit/s)
13
n N
14
Error n N
(%)
14.7456
Error n N
(%)
110
2 230 –0.08 2 248 –0.17 3 64
150
2 168 0.16
300
2 84
600
1 168 0.16
1200
1 84
2400
0 168 0.16
2 181 0.16
–0.43 2 90
0.16
1 181 0.16
–0.43 1 90
0.16
0 181 0.16
16
18
20
Error n N
(%)
Error n N
(%)
Error n N
(%)
Error
(%)
0.70
0.03
–0.12 3 88
–0.25
3 70
3 79
2 191 0.00
2 207 0.16
2 233 0.16
3 64
0.16
2 95
0.00
2 103 0.16
2 116 0.16
2 129 0.16
1 191 0.00
1 207 0.16
1 233 0.16
2 64
1 95
0.00
1 103 0.16
1 116 0.16
1 129 0.16
0 191 0.00
0 207 0.16
0 233 0.16
1 64
0 129 0.16
0.16
0.16
4800
0 84
–0.43 0 90
0.16
0 95
0.00
0 103 0.16
0 116 0.16
9600
0 41
0.76
0 45
–0.93 0 47
0.00
0 51
0.16
0 58
–0.69 0 64
0.16
19200
0 20
0.76
0 22
–0.93 0 23
0.00
0 25
0.16
0 28
1.02
0 32
–1.36
31250
0 12
0.00
0 13
0.00
0 14
–1.70 0 15
0.00
0 17
0.00
0 19
0.00
38400
0 10
–3.82 0 10
3.57
0 11
0.00
0.16
0 14
–2.34 0 15
1.73
0 12
Rev. 3.00 Sep 14, 2005 page 491 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Table 13.4 Examples of Bit Rates and BRR Settings in Synchronous Mode
φ (MHz)
Bit
Rate
2
4
8
10
13
16
18
20
(bit/s) n
N
n
N
n
N
n
N
n
N
n
N
n
N
n
N
110
3
70
—
—
—
—
—
—
—
—
—
—
—
—
—
—
250
2
124
2
249
3
124
—
—
3
202
3
249
—
—
—
—
500
1
249
2
124
2
249
—
—
3
101
3
124
3
140
3
155
1k
1
124
1
249
2
124
—
—
2
202
2
249
3
69
3
77
2.5k
0
199
1
99
1
199
1
249
2
80
2
99
2
112
2
124
5k
0
99
0
199
1
99
1
124
1
162
1
199
1
224
1
249
10k
0
49
0
99
0
199
0
249
1
80
1
99
1
112
1
124
25k
0
19
0
39
0
79
0
99
0
129
0
159
0
179
0
199
50k
0
9
0
19
0
39
0
49
0
64
0
79
0
89
0
99
100k
0
4
0
9
0
19
0
24
—
—
0
39
0
44
0
49
250k
0
1
0
3
0
7
0
9
0
12
0
15
0
17
0
19
500k
0
0*
0
1
0
3
0
4
—
—
0
7
0
8
0
9
0
0*
0
1
—
—
—
—
0
3
0
4
0
4
2M
0
0*
—
—
—
—
0
1
—
—
—
—
2.5M
—
—
0
0*
—
—
—
—
—
—
—
—
0
0*
—
—
—
—
1M
4M
Note: Settings with an error of 1% or less are recommended.
Legend
Blank : No setting available
—:
Setting possible, but error occurs
*:
Continuous transmission/reception not possible
Rev. 3.00 Sep 14, 2005 page 492 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
The BRR setting is calculated as follows:
Asynchronous mode:
N=
φ
64 × 22n–1 × B
× 106 – 1
Synchronous mode:
N=
B:
N:
φ:
n:
φ
8 × 22n–1 × B
× 106 – 1
Bit rate (bit/s)
BRR setting for baud rate generator (0 ≤ N ≤ 255)
System clock frequency (MHz)
Baud rate generator clock source (n = 0, 1, 2, 3)
(For the clock sources and values of n, see the following table.)
SMR Settings
n
Clock Source
CKS1
CKS0
0
φ
0
0
1
φ/4
0
1
2
φ/16
1
0
3
φ/64
1
1
The bit rate error in asynchronous mode is calculated as follows:
Error (%) =
φ × 106
(N + 1) × B × 64 × 22n–1
–1
× 100
Rev. 3.00 Sep 14, 2005 page 493 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Table 13.5 shows the maximum bit rates in asynchronous mode for various system clock
frequencies. Table 13.6 and 13.7 shows the maximum bit rates with external clock input.
Table 13.5 Maximum Bit Rates for Various Frequencies (Asynchronous Mode)
Settings
φ (MHz)
Maximum Bit Rate (bit/s)
n
N
2
62500
0
0
2.097152
65536
0
0
2.4576
76800
0
0
3
93750
0
0
3.6864
115200
0
0
4
125000
0
0
4.9152
153600
0
0
5
156250
0
0
6
187500
0
0
6.144
192000
0
0
7.3728
230400
0
0
8
250000
0
0
9.8304
307200
0
0
10
312500
0
0
12
375000
0
0
12.288
384000
0
0
14
437500
0
0
14.7456
460800
0
0
16
500000
0
0
17.2032
537600
0
0
18
562500
0
0
20
625000
0
0
Rev. 3.00 Sep 14, 2005 page 494 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Table 13.6 Maximum Bit Rates with External Clock Input (Asynchronous Mode)
φ (MHz)
External Input Clock (MHz)
Maximum Bit Rate (bit/s)
2
0.5000
31250
2.097152
0.5243
32768
2.4576
0.6144
38400
3
0.7500
46875
3.6864
0.9216
57600
4
1.0000
62500
4.9152
1.2288
76800
5
1.2500
78125
6
1.5000
93750
6.144
1.5360
96000
7.3728
1.8432
115200
8
2.0000
125000
9.8304
2.4576
153600
10
2.5000
156250
12
3.0000
187500
12.288
3.0720
192000
14
3.5000
218750
14.7456
3.6864
230400
16
4.0000
250000
17.2032
4.3008
268800
18
4.5000
281250
20
5.0000
312500
Rev. 3.00 Sep 14, 2005 page 495 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Table 13.7 Maximum Bit Rates with External Clock Input (Synchronous Mode)
φ (MHz)
External Input Clock (MHz)
Maximum Bit Rate (bit/s)
2
0.3333
333333.3
4
0.6667
666666.7
6
1.0000
1000000.0
8
1.3333
1333333.3
10
1.6667
1666666.7
12
2.0000
2000000.0
14
2.3333
2333333.3
16
2.6667
2666666.7
18
3.0000
3000000.0
20
3.3333
3333333.3
Rev. 3.00 Sep 14, 2005 page 496 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.3
Operation
13.3.1
Overview
The SCI can carry out serial communication in two modes: asynchronous mode in which
synchronization is achieved character by character, and synchronous mode in which
synchronization is achieved with clock pulses. A smart card interface is also supported as a serial
communication function for an IC card interface.
Selection of asynchronous or synchronous mode and the transmission format for the normal serial
communication interface is made in SMR, as shown in table 13.8. The SCI clock source is
selected by the C/A bit in SMR and the CKE1 and CKE0 bits in SCR, as shown in table 13.9.
For details of the procedures for switching between LSB-first and MSB-first mode and inverting
the data logic level, see section 14.2.1, Smart Card Mode Register (SCMR).
For selection of the smart card interface format, see section 14.3.3, Data Format.
Asynchronous Mode
• Data length is selectable: 7 or 8 bits
• Parity and multiprocessor bits are selectable, and so is the stop bit length (1 or 2 bits). These
selections determine the communication format and character length.
• In receiving, it is possible to detect framing errors, parity errors, overrun errors, and the break
state.
• An internal or external clock can be selected as the SCI clock source.
 When an internal clock is selected, the SCI operates using the on-chip baud rate generator,
and can output a serial clock signal with a frequency matching the bit rate.
 When an external clock is selected, the external clock input must have a frequency 16
times the bit rate. (The on-chip baud rate generator is not used.)
Synchronous Mode
• The communication format has a fixed 8-bit data length.
• In receiving, it is possible to detect overrun errors.
• An internal or external clock can be selected as the SCI clock source.
 When an internal clock is selected, the SCI operates using the on-chip baud rate generator,
and can output a serial clock signal to external devices.
 When an external clock is selected, the SCI operates on the input serial clock. The on-chip
baud rate generator is not used.
Rev. 3.00 Sep 14, 2005 page 497 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Smart Card Interface
• One frame consists of 8-bit data and a parity bit.
• In transmitting, a guard time of at least two elementary time units (2 etu) is provided between
the end of the parity bit and the start of he next frame. (An elementary time unit is the time
required to transmit one bit.)
• In receiving, if a parity error is detected, a low error signal level is output for 1 etu, beginning
10.5 etu after the start bit..
• In transmitting, if an error signal is received, the same data is automatically transmitted again
after at least 2 etu.
• Only asynchronous communication is supported. There is no synchronous communication
function.
For details of smart card interface operation, see section 14, Smart Card Interface.
Table 13.8 SMR Settings and Serial Communication Formats
SMR Settings
SCI Communication Format
Bit 7
C/A
Bit 6
CHR
Bit 2
MP
Bit 5
PE
Bit 3
STOP
0
0
0
0
0
1
0
1
Mode
AsynChronous
mode
Data
Length
Multiprocessor
Bit
Parity
Bit
Stop Bit
Length
8-bit data
Absent
Absent
1 bit
2 bits
Present
1
1
0
2 bits
0
7-bit data
Absent
1
1
0
1
—
0
—
1
1
—
0
—
1
1
—
—
—
—
1 bit
2 bits
Present
1
0
1 bit
1 bit
2 bits
Asyn8-bit data
chronous
mode (multi7-bit data
processor
format)
Present
Synchronous
mode
Absent
Rev. 3.00 Sep 14, 2005 page 498 of 910
REJ09B0258-0300
8-bit data
Absent
1 bit
2 bits
1 bit
2 bits
None
Section 13 Serial Communication Interface
Table 13.9 SMR and SCR Settings and SCI Clock Source Selection
SMR
SCR Setting
SCI Transmit/Receive clock
Bit 7
C/A
Bit 1 Bit 0
CKE1 CKE0 Mode
Clock Source SCK Pin Function
0
0
0
1
1
Asynchronous
mode
0
Internal
Outputs clock with frequency matching the
bit rate
External
Inputs clock with frequency 16 times the bit
rate
Internal
Outputs the serial clock
External
Inputs the serial clock
1
1
0
0
1
1
0
Synchronous
mode
SCI does not use the SCK pin
1
13.3.2
Operation in Asynchronous Mode
In asynchronous mode, each transmitted or received character begins with a start bit and ends
with one or two stop bits. Serial communication is synchronized one character at a time.
The transmitting and receiving sections of the SCI are independent, so full-duplex communication
is possible. The transmitter and the receiver are both double-buffered, so data can be written and
read while transmitting and receiving are in progress, enabling continuous transmitting and
receiving.
Figure 13.2 shows the general format of asynchronous serial communication. In asynchronous
serial communication the communication line is normally held in the mark (high) state. The SCI
monitors the line and starts serial communication when the line goes to the space (low) state,
indicating a start bit. One serial character consists of a start bit (low), data (LSB first), parity bit
(high or low), and one or two stop bits (high), in that order.
When receiving in asynchronous mode, the SCI synchronizes at the falling edge of the start bit.
The SCI samples each data bit on the eighth pulse of a clock with a frequency 16 times the bit
rate. Receive data is latched at the center of each bit.
Rev. 3.00 Sep 14, 2005 page 499 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Idle (mark) state
(LSB)
1
Serial
data
0
Start
bit
1 bit
D0
1
(MSB)
D1
D2
D3
D4
D5
D6
Transmit or receive data
7 or 8 bits
One unit of data (character or frame)
D7
0/1
Parity
bit
1 bit,
or
none
1
1
Stop bit(s)
1 or 2 bits
Figure 13.2 Data Format in Asynchronous Communication
(Example: 8-Bit Data with Parity and 2 Stop Bits)
Communication Formats: Table 13.10 shows the 12 communication formats that can be
selected in asynchronous mode. The format is selected by settings in SMR.
Rev. 3.00 Sep 14, 2005 page 500 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Table 13.10 Serial Communication Formats (Asynchronous Mode)
SMR Settings
Serial Communication Format and Frame Length
CHR
PE
MP
STOP
1
2
3
4
5
6
7
8
9
10
11
12
0
0
0
0
S
8-bit data
STOP
0
0
0
1
S
8-bit data
STOP STOP
0
1
0
0
S
8-bit data
P STOP
0
1
0
1
S
8-bit data
P STOP STOP
1
0
0
0
S
7-bit data
1
0
0
1
S
7-bit data
STOP STOP
1
1
0
0
S
7-bit data
P STOP
1
1
0
1
S
7-bit data
P STOP STOP
0
—
1
0
S
8-bit data
MPB STOP
0
—
1
1
S
8-bit data
MPB STOP STOP
1
—
1
0
S
7-bit data
MPB STOP
1
—
1
1
S
7-bit data
MPB STOP STOP
STOP
Legend
S:
Start bit
STOP: Stop bit
P:
Parity bit
MPB: Multiprocessor bit
Rev. 3.00 Sep 14, 2005 page 501 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Clock: An internal clock generated by the on-chip baud rate generator or an external clock input
from the SCK pin can be selected as the SCI transmit/receive clock. The clock source is selected
by the C/A bit in SMR and bits CKE1 and CKE0 in SCR. For details of SCI clock source
selection, see table 13.9.
When an external clock is input at the SCK pin, it must have a frequency 16 times the desired bit
rate.
When the SCI is operated on an internal clock, it can output a clock signal at the SCK pin. The
frequency of this output clock is equal to the bit rate. The phase is aligned as shown in figure
13.3 so that the rising edge of the clock occurs at the center of each transmit data bit.
0
D0
D1
D2
D3
D4
D5
D6
D7
0/1
1
1
1frame
Figure 13.3 Phase Relationship between Output Clock and Serial Data
(Asynchronous Mode)
Transmitting and Receiving Data:
• SCI Initialization (Asynchronous Mode): Before transmitting or receiving data, clear the TE
and RE bits to 0 in SCR, then initialize the SCI as follows.
When changing the communication mode or format, always clear the TE and RE bits to 0
before following the procedure given below. Clearing TE to 0 sets the TDRE flag to 1 and
initializes TSR. Clearing RE to 0, however, does not initialize the RDRF, PER, FER, and
ORER flags, or RDR, which retain their previous contents.
When an external clock is used the clock should not be stopped during initialization or
subsequent operation, since operation will be unreliable in this case.
Rev. 3.00 Sep 14, 2005 page 502 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Figure 13.4 shows a sample flowchart for initializing the SCI.
Start of initialization
Clear TE and RE bits
to 0 in SCR
Set CKE1 and CKE0 bits in SCR
(leaving TE and RE bits
cleared to 0)
(1)
Select communication format
in SMR
(2)
Set value in BRR
(3)
Wait
(1)
Set the clock source in SCR. Clear the
RIE, TIE, TEIE, MPIE, TE, and RE bits to
0. If clock output is selected in
asynchronous mode, clock output starts
immediately after the setting is made in
SCR.
(2)
Select the communication format in SMR.
(3)
Write the value corresponding to the bit
rate in BRR.
This step is not necessary when an
external clock is used.
(4)
Wait for at least the interval required to
transmit or receive one bit, then set the
TE or RE bit to 1 in SCR. Set the RIE,
TIE, TEIE, and MPIE bits as necessary.
Setting the TE or RE bit enables the SCI
to use the TxD or RxD pin.
No
1-bit interval elapsed?
Yes
Set TE or RE bit to 1 in SCR
Set the RIE, TIE, TEIE, and
MPIE bits
(4)
<End of initialization>
Note: In simultaneous transmitting and receiving, the TE and RE bits should be cleared to
0 or set to 1 simultaneously.
Figure 13.4 Sample Flowchart for SCI Initialization
Rev. 3.00 Sep 14, 2005 page 503 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
• Transmitting Serial Data (Asynchronous Mode): Figure 13.5 shows a sample flowchart for
transmitting serial data and indicates the procedure to follow.
(1)
Initialize
Start transmitting
(2)
Read TDRE flag in SSR
No
TDRE = 1
Write transmit data in TDR
and clear TDRE flag to 0 in SSR
No
Yes
(2) SCI status check and transmit data write:
read SSR and check that the TDRE flag is set to 1,
then write transmit data in TDR and clear the TDRE
flag to 0.
(3) To continue transmitting serial data:
after checking that the TDRE flag is 1, indicating that
data can be written, write data in TDR, then clear the
TDRE flag to 0. When the DMAC is activated by a
transmit-data-empty interrupt request (TXI) to write
data in TDR, the TDRE flag is checked and cleared
automatically.
Yes
All data transmitted?
(1) SCI initialization:
the transmit data output function of the TxD pin is
selected automatically.
(3)
(4) To output a break signal at the end of serial
transmission:
set the DDR bit to 1 and clear the DR bit to 0, then
clear the TE bit to 0 in SCR.
Read TEND flag in SSR
TEND = 1
No
Yes
Output break signal?
No
(4)
Yes
Clear DR bit to 0 and set
DDR bit to 1
Clear TE bit to 0 in SCR
<End>
Figure 13.5 Sample Flowchart for Transmitting Serial Data
Rev. 3.00 Sep 14, 2005 page 504 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
In transmitting serial data, the SCI operates as follows:
• The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0, the SCI
recognizes that TDR contains new data, and loads this data from TDR into TSR.
• After loading the data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts
transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty
interrupt (TXI) at this time.
Serial transmit data is transmitted in the following order from the TxD pin:
 Start bit: One 0 bit is output.
 Transmit data: 7 or 8 bits are output, LSB first.
 Parity bit or multiprocessor bit: One parity bit (even or odd parity),or one multiprocessor
bit is output. Formats in which neither a parity bit nor a multiprocessor bit is output can
also be selected.
 Stop bit(s): One or two 1 bits (stop bits) are output.
 Mark state: Output of 1 bits continues until the start bit of the next transmit data.
• The SCI checks the TDRE flag when it outputs the stop bit. If the TDRE flag is 0, the SCI
loads new data from TDR into TSR, outputs the stop bit, then begins serial transmission of the
next frame. If the TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, outputs the stop
bit, then continues output of 1 bits in the mark state. If the TEIE bit is set to 1 in SCR, a
transmit-end interrupt (TEI) is requested at this time
Figure 13.6 shows an example of SCI transmit operation in asynchronous mode.
1
0
Parity Stop Start
bit
bit
bit
Data
Start bit
D0
D1
D7
0/1
1
0
Parity Stop
bit
bit
Data
D0
D1
D7
0/1
1
1
Idle state
(mark state)
TDRE
TEND
1 frame
TXI interrupt
request
TXI interrupt handler
writes data in TDR and
clears TDRE flag to 0
TXI interrupt
request
TEI interrupt
request
Figure 13.6 Example of SCI Transmit Operation in Asynchronous Mode
(8-Bit Data with Parity and One Stop Bit)
Rev. 3.00 Sep 14, 2005 page 505 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
• Receiving Serial Data (Asynchronous Mode): Figure 13.7 shows a sample flowchart for
receiving serial data and indicates the procedure to follow.
(1)
Initialize
(1)
SCI initialization:
the receive data input function of the RxD
pin is selected automatically.
(2)(3)
Receive error handling and break detection:
if a receive error occurs, read the ORER,
PER, and FER flags in SSR to identify the
error. After executing the necessary error
handling, clear the ORER, PER, and FER
flags all to 0. Receiving cannot resume if
any of these flags remains set to 1. When a
framing error occurs, the RxD pin can be
read to detect the break state.
Start receiving
Read ORER, PER, and FER
flags in SSR
(2)
Yes
PER⁄FER⁄OPER = 1
(3)
Error handling
No
(continued on next page)
Read RDRF flag in SSR
No
(4)
(4)
SCI status check and receive data read:
read SSR, check that the RDRF flag is set
to 1, then read receive data from RDR and
clear the RDRF flag to 0. Notification that
the RDRF flag has changed from 0 to 1 can
also be given by the RXI interrupt.
(5)
To continue receiving serial data:
check the RDRF flag, read RDR, and clear
the RDRF flag to 0 before the stop bit of the
current frame is received. When the DMAC
is activated by a receive-data-full interrupt
request (RXI) to read RDR, the RDRF flag
is cleared automatically.
RDRF = 1
Yes
Read receive data from RDR, and
clear RDRF flag to 0 in SSR
No
All data received?
(5)
Yes
Clear RE bit to 0 in SCR
<End>
Figure 13.7 Sample Flowchart for Receiving Serial Data (1)
Rev. 3.00 Sep 14, 2005 page 506 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
(3)
Error handling
No
ORER = 1
Yes
Overrun error handling
No
FER = 1
Yes
Break?
Yes
No
Framing error handling
No
Clear RE bit to 0 in SCR
PER = 1
Yes
Parity error handling
Clear ORER, PER, and FER flags
to 0 in SSR
<End>
Figure 13.7 Sample Flowchart for Receiving Serial Data (2)
Rev. 3.00 Sep 14, 2005 page 507 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
In receiving, the SCI operates as follows:
• The SCI monitors the communication line. When it detects a start bit (0 bit), the SCI
synchronizes internally and starts receiving.
• Receive data is stored in RSR in order from LSB to MSB.
• The parity bit and stop bit are received.
After receiving these bits, the SCI carries out the following checks:
 Parity check: The number of 1s in the receive data must match the even or odd parity
setting of in the O/E bit in SMR.
 Stop bit check: The stop bit value must be 1. If there are two stop bits, only the first is
checked.
 Status check: The RDRF flag must be 0, indicating that the receive data can be transferred
from RSR into RDR.
If these all checks pass, the RDRF flag is set to 1 and the received data is stored in RDR. If
one of the checks fails (receive error*), the SCI operates as shown in table 13.11.
Note: * When a receive error occurs, further receiving is disabled. In receiving, the RDRF flag is
not set to 1. Be sure to clear the error flags to 0.
• When the RDRF flag is set to 1, if the RIE bit is set to 1 in SCR, a receive-data-full interrupt
(RXI) is requested. If the ORER, PER, or FER flag is set to 1 and the RIE bit in SCR is also
set to 1, a receive-error interrupt (ERI) is requested.
Table 13.11 Receive Error Conditions
Receive Error Abbreviation Condition
Data Transfer
Overrun error ORER
Receiving of next data ends while Receive data is not transferred
RDRF flag is still set to 1 in SSR from RSR to RDR
Framing error FER
Stop bit is 0
Parity error
Parity of received data differs from Receive data is transferred from
even/odd parity setting in SMR
RSR to RDR
PER
Rev. 3.00 Sep 14, 2005 page 508 of 910
REJ09B0258-0300
Receive data is transferred from
RSR to RDR
Section 13 Serial Communication Interface
Figure 13.8 shows an example of SCI receive operation in asynchronous mode.
1
Start
bit
0
Parity Stop
bit
bit
Data
D0
D1
D7
0/1
1
Start
bit
0
Data
D0
D1
Stop Parity Stop
bit
bit
bit
D7
0/1
1
1
Idle (mark) state
RDRF
FER
RXI request
1 frame
RXI interrupt handler
reads data in RDR and
clears RDRF flag to 0
Framing error,
ERI request
Figure 13.8 Example of SCI Receive Operation
(8-Bit Data with Parity and One Stop Bit)
13.3.3
Multiprocessor Communication
The multiprocessor communication function enables several processors to share a single serial
communication line. The processors communicate in asynchronous mode using a format with an
additional multiprocessor bit (multiprocessor format).
In multiprocessor communication, each receiving processor is addressed by an ID. A serial
communication cycle consists of an ID-sending cycle that identifies the receiving processor, and a
data-sending cycle. The multiprocessor bit distinguishes ID-sending cycles from data-sending
cycles.
The transmitting processor stars by sending the ID of the receiving processor with which it wants
to communicate as data with the multiprocessor bit set to 1. Next the transmitting processor
sends transmit data with the multiprocessor bit cleared to 0.
Receiving processors skip incoming data until they receive data with the multiprocessor bit set to
1. When they receive data with the multiprocessor bit set to 1, receiving processors compare the
data with their IDs. Processors with IDs not matching the received data skip further incoming
data until they again receive data with the multiprocessor bit set to 1. Multiple processors can
send and receive data in this way.
Figure 13.9 shows an example of communication among different processors using a
multiprocessor format.
Rev. 3.00 Sep 14, 2005 page 509 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Communication Formats: Four formats are available. Parity bit settings are ignored when a
multiprocessor format is selected. For details see table 13.10.
Clock: See the description of asynchronous mode.
Transmitting
processor
Serial communication line
Serial data
Receiving
processor A
Receiving
processor B
Receiving
processor C
Receiving
processor D
(ID=01)
(ID=02)
(ID=03)
(ID=04)
H'AA
H'01
(MPB=1)
ID-sending cycle:
receiving processor address
(MPB=0)
Data-sending cycle:
data sent to receiving processor
specified by ID
Legend
MPB : Multiprocessor bit
Figure 13.9 Example of Communication among Processors using Multiprocessor Format
(Sending Data H'AA to Receiving Processor A)
Transmitting and Receiving Data:
• Transmitting Multiprocessor Serial Data: Figure 13.10 shows a sample flowchart for
transmitting multiprocessor serial data and indicates the procedure to follow.
Rev. 3.00 Sep 14, 2005 page 510 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
(1)
Initialize
(1)
SCI initialization:
the transmit data output function of the TxD pin
is selected automatically.
(2)
SCI status check and transmit data write:
read SSR, check that the TDRE flag is 1, then
write transmit data in TDR. Also set the MPBT
flag to 0 or 1 in SSR. Finally, clear the TDRE
flag to 0.
(3)
To continue transmitting serial data:
after checking that the TDRE flag is 1,
indicating that data can be written, write data
in TDR, then clear the TDRE flag to 0. When
the DMAC is activated by a transmit-dataempty interrupt request (TXI) to write data in
TDR, the TDRE flag is checked and cleared
automatically.
(4)
To output a break signal at the end of serial
transmission:
set the DDR bit to 1 and clear the DR bit to 0,
then clear the TE bit to 0 in SCR.
Start transmitting
Read TDRE flag in SSR
TDRE = 1
(2)
No
Yes
Write transmit data in TDR
and set MPBT bit in SSR
Clear TDRE flag to 0
All data transmitted?
No
(3)
Yes
Read TEND flag in SSR
TEND = 1
No
Yes
Output break signal?
No
(4)
Yes
Clear DR bit to 0 and set DDR to 1
Clear TE bit to 0 in SCR
<End>
Figure 13.10 Sample Flowchart for Transmitting Multiprocessor Serial Data
Rev. 3.00 Sep 14, 2005 page 511 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
In transmitting serial data, the SCI operates as follows:
• The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0, the SCI
recognizes that TDR contains new data, and loads this data from TDR into TSR.
• After loading the data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts
transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty
interrupt (TXI) at this time.
Serial transmit data is transmitted in the following order from the TxD pin:
 Start bit: One 0 bit is output.
 Transmit data: 7 or 8 bits are output, LSB first.
 Multiprocessor bit: One multiprocessor bit (MPBT value) is output.
 Stop bit(s): One or two 1 bits (stop bits) are output.
 Mark state: Output of 1 bits continues until the start bit of the next transmit data.
• The SCI checks the TDRE flag when it outputs the stop bit. If the TDRE flag is 0, the SCI
loads new data from TDR into TSR, outputs the stop bit, then begins serial transmission of the
next frame. If the TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, outputs the stop
bit, then continues output of 1 bits in the mark state. If the TEIE bit is set to 1 in SCR, a
transmit-end interrupt (TEI) is requested at this time
Figure 13.11 shows an example of SCI transmit operation using a multiprocessor format.
1
Start
bit
0
Data
D0
D1
Multiprocessor Stop Start
bit
bit
bit
D7
0/1
1
0
Data
D0
D1
Multiprocessor Stop
bit
bit
D7
0/1
1
Idle (mark)
state
TDRE
TEND
TXI interrupt TXI interrupt handler
writes data in TDR and
request
clears TDRE flag to 0
TXI interrupt
request
TEI interrupt
request
1 frame
Figure 13.11 Example of SCI Transmit Operation
(8-Bit Data with Multiprocessor Bit and One Stop Bit)
• Receiving Multiprocessor Serial Data: Figure 13.12 shows a sample flowchart for receiving
multiprocessor serial data and indicates the procedure to follow.
Rev. 3.00 Sep 14, 2005 page 512 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
(1)
Initialize
(1)
SCI initialization:
the receive data input function of the
RxD pin is selected automatically.
(2)
ID receive cycle:
set the MPIE bit to 1 in SCR.
(3)
SCI status check and ID check:
read SSR, check that the RDRF flag
is set to 1, then read data from RDR
and compare it with the processor's
own ID. If the ID does not match, set
the MPIE bit to 1 again and clear the
RDRF flag to 0. If the ID matches,
clear the RDRF flag to 0.
(4)
SCI status check and data receiving:
read SSR, check that the RDRF flag
is set to 1, then read data from RDR.
(5)
Receive error handling and break
detection:
if a receive error occurs, read the
ORER and FER flags in SSR to
identify the error. After executing the
necessary error handling, clear the
ORER and FER flags both to 0.
Receiving cannot resume while either
the ORER or FER flag remains set to
1. When a framing error occurs, the
RxD pin can be read to detect the
break state.
Start receiving
(2)
Set MPIE bit to 1 in SCR
Read ORER and FER flags
in SSR
FER⁄ORER = 1
Yes
No
Read RDRF flag in SSR
No
(3)
RDRF = 1
Yes
Read RDRF flag in SSR
No
Own ID?
Yes
Read ORER and FER flags
in SSR
FER⁄ORER = 1
Yes
No
(4)
Read RDRF flag in SSR
RDRF = 1
No
Yes
Read receive data from RDR
No
Finished receiving?
Yes
Clear RE bit to 0 in SCR
(5)
Error handling
(continued on next page)
<End>
Figure 13.12 Sample Flowchart for Receiving Multiprocessor Serial Data (1)
Rev. 3.00 Sep 14, 2005 page 513 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
(5)
Error handling
No
ORER = 1
Yes
Overrun error handling
No
FER = 1
Yes
Break?
Yes
No
Clear RE bit to 0 in SCR
Framing error handling
Clear ORER, PER, and FER
flags to 0 in SSR
<End>
Figure 13.12 Sample Flowchart for Receiving Multiprocessor Serial Data (2)
Rev. 3.00 Sep 14, 2005 page 514 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Figure 13.13 shows an example of SCI receive operation using a multiprocessor format.
1
Start
bit
0
Stop
MPB bit
Data (ID1)
D0
D7
D1
1
Start
bit
0
1
Stop
MPB bit
Data (data1)
D0
D1
D7
1
0
1
Idle (mark)
state
MPIE
RDRF
RDR value
ID1
MPB detection
MPIE = 0
RXI interrupt
request
(multiprocessor
interrupt)
RXI interrupt handler reads
RDR data and clears
RDRF flag to 0
Not own ID, so MPIE
bit is set to 1 again
No RXI interrupt
request, RDR not
updated
a. Own ID does not match data
1
Start
bit
0
Data (ID2)
D0
D1
MPB
D7
1
Stop
bit
1
Start
bit
Data (data1)
0
D0
D1
MPB
D7
0
Stop
bit
1
1
Idle (mark)
state
MPIE
RDRF
RDR value
ID1
MPB detection
MPIE = 0
ID2
RXI interrupt
request
(multiprocessor
interrupt)
RXI interrupt handler
reads RDR data and
clears RDRF flag to 0
Data2
Own ID, so receiving MPIE bit is set to
continues, with data 1 again
received by RXI
interrupt handler
b. Own ID matches data
Figure 13.13 Example of SCI Receive Operation
(8-Bit Data with Multiprocessor Bit and One Stop Bit)
Rev. 3.00 Sep 14, 2005 page 515 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.3.4
Synchronous Operation
In synchronous mode, the SCI transmits and receives data in synchronization with clock pulses.
This mode is suitable for high-speed serial communication.
The SCI transmitter and receiver share the same clock but are otherwise independent, so fullduplex communication is possible. The transmitter and the receiver are also double-buffered, so
continuous transmitting or receiving is possible by reading or writing data while transmitting or
receiving is in progress.
Figure 13.14 shows the general format in synchronous serial communication.
One unit (character or frame) of transfer data
*
*
Serial clock
LSB
Bit 0
Serial data
MSB
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Don't care
Don't care
Note: * High except in continuous transmitting or receiving
Figure 13.14 Data Format in Synchronous Communication
In synchronous serial communication, each data bit is placed on the communication line from one
falling edge of the serial clock to the next. Data is guaranteed valid at the rise of the serial clock.
In each character, the serial data bits are transferred in order from LSB (first) to MSB (last).
After output of the MSB, the communication line remains in the state of the MSB. In
synchronous mode the SCI receives data by synchronizing with the rise of the serial clock.
Communication Format: The data length is fixed at 8 bits. No parity bit or multiprocessor bit
can be added.
Clock: An internal clock generated by the on-chip baud rate generator or an external clock input
from the SCK pin can be selected by means of the C/A bit in SMR and the CKE1 and CKE0 bits
in SCR. See table 13.6 for details of SCI clock source selection.
When the SCI operates on an internal clock, it outputs the clock source at the SCK pin. Eight
clock pulses are output per transmitted or received character. When the SCI is not transmitting or
receiving, the clock signal remains in the high state. If receiving in single-character units is
required, an external clock should be selected.
Rev. 3.00 Sep 14, 2005 page 516 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Transmitting and Receiving Data:
• SCI Initialization (Synchronous Mode): Before transmitting or receiving data, clear the TE
and RE bits to 0 in SCR, then initialize the SCI as follows.
When changing the communication mode or format, always clear the TE and RE bits to 0
before following the procedure given below. Clearing TE to 0 sets the TDRE flag to 1 and
initializes TSR. Note that clearing RE to 0, however, does not initialize the RDRF, PER, and
ORE flags, or RDR, which retain their previous contents.
Rev. 3.00 Sep 14, 2005 page 517 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Figure 13.15 shows a sample flowchart for initializing the SCI.
Start of initialization
Clear TE and RE bits to 0 in SCR
Set RIE, TIE, TEIE, MPIE, CKE1,
(1)
and CKE0 bits in SCR (leaving
TE and RE bits cleared to 0)
Select communication format
in SMR
Set value in BRR
Wait
1-bit interval elapsed?
(2)
(3)
(1)
Set the clock source in SCR. Clear the RIE,
TIE, TEIE, MPIE, TE, and RE bits to 0.*
(2)
Select the communication format in SMR.
(3)
Write the value corresponding to the bit rate in
BRR.
This step is not necessary when an external
clock is used.
(4)
Wait for at least the interval required to transmit
or receive one bit, then set the TE or RE bit to
1 in SCR.* Set the RIE, TIE, TEIE, and MPIE
bits as necessary. Setting the TE or RE bit
enables the SCI to use the TxD or RxD pin.
Note: * In simultaneous transmitting and receiving,
the TE and RE bits should be cleared to 0 or
set to 1 simultaneously.
No
Yes
Set TE or RE bit to 1 in SCR
Set RIE, TIE, TEIE, and MPIE
bits as necessary
(4)
<Start transmitting or receiving>
Figure 13.15 Sample Flowchart for SCI Initialization
Rev. 3.00 Sep 14, 2005 page 518 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
• Transmitting Serial Data (Synchronous Mode): Figure 13.16 shows a sample flowchart for
transmitting serial data and indicates the procedure to follow.
(1)
Initialize
(1)
SCI initialization: the transmit data output
function of the TxD pin is selected
automatically.
(2)
SCI status check and transmit data write:
read SSR, check that the TDRE flag is 1, then
write transmit data in TDR and clear the
TDRE flag to 0.
(3)
To continue transmitting serial data: after
checking that the TDRE flag is 1, indicating
that data can be written, write data in TDR,
then clear the TDRE flag to 0. When the
DMAC is activated by a transmit-data-empty
interrupt request (TXI) to write data in TDR,
the TDRE flag is checked and cleared
automatically.
Start transmitting
Read TDRE flag in SSR
TDRE = 1
(2)
No
Yes
Write transmit data in TDR
and clear TDRE flag to 0 in SSR
All data transmitted?
No
(3)
Yes
Read TEND flag in SSR
TEND = 1
No
Yes
Clear TE bit to 0 in SCR
<End>
Figure 13.16 Sample Flowchart for Serial Transmitting
Rev. 3.00 Sep 14, 2005 page 519 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
In transmitting serial data, the SCI operates as follows.
• The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0, the SCI
recognizes that TDR contains new data, and loads this data from TDR into TSR.
• After loading the data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts
transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty
interrupt (TXI) at this time.
If clock output is selected, the SCI outputs eight serial clock pulses. If an external clock
source is selected, the SCI outputs data in synchronization with the input clock. Data is
output from the TxD pin n order from LSB (bit 0) to MSB (bit 7).
• The SCI checks the TDRE flag when it outputs the MSB (bit 7). If the TDRE flag is 0, the
SCI loads data from TDR into TSR and begins serial transmission of the next frame. If the
TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, and after transmitting the MSB (bit
7), holds the TxD pin in the MSB state. If the TEIE bit is set to 1 in SCR, a transmit-end
interrupt (TEI) is requested at this time
• After the end of serial transmission, the SCK pin is held in a constant state.
Figure 13.17 shows an example of SCI transmit operation.
Transmit direction
Serial clock
Serial data
Bit 0
Bit 1
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
TDRE
TEND
TXI interrupt
request
TXI interrupt handler TXI interrupt
writes data in TDR
request
and clears TDRE
flag to 0
1 frame
Figure 13.17 Example of SCI Transmit Operation
Rev. 3.00 Sep 14, 2005 page 520 of 910
REJ09B0258-0300
TEI interrupt
request
Section 13 Serial Communication Interface
• Receiving Serial Data (Synchronous Mode): Figure 13.18 shows a sample flowchart for
receiving serial data and indicates the procedure to follow. When switching from
asynchronous to synchronous mode. make sure that the ORER, PER, and FER flags are
cleared to 0. If the FER or PER flag is set to 1 the RDRF flag will not be set and both
transmitting and receiving will be disabled.
(1)
Initialize
(1)
Start receiving
Read ORER flag in SSR
(2)
Yes
ORER = 1
(3)
No
Error handling
(2)(3) Receive error handling: if a receive
error occurs, read the ORER flag in
SSR, then after executing the
necessary error handling, clear the
ORER flag to 0. Neither transmitting
nor receiving can resume while the
ORER flag remains set to 1.
(4)
SCI status check and receive data
read: read SSR, check that the RDRF
flag is set to 1, then read receive data
from RDR and clear the RDRF flag to
0. Notification that the RDRF flag
has changed from 0 to 1 can also be
given by the RXI interrupt.
(5)
To continue receiving serial data:
check the RDRF flag, read RDR, and
clear the RDRF flag to 0 before the
MSB (bit 7) of the current frame is
received. When the DMAC is
activated by a receive-data-full
interrupt request (RXI) to read RDR,
the RDRF flag is cleared
automatically.
(continued on next page)
Read RDRF flag in SSR
No
(4)
RDRF = 1
Yes
Read receive data from
RDR, and clear RDRF
flag to 0 in SSR
No
Finished receiving?
(5)
SCI initialization: the receive data
input function of the RxD pin is
selected automatically.
Yes
Clear RE bit to 0 in SCR
<End>
Figure 13.18 Sample Flowchart for Serial Receiving (1)
Rev. 3.00 Sep 14, 2005 page 521 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
(3)
Error handling
Overrun error handling
Clear ORER flag to 0 in SSR
<End>
Figure 13.18 Sample Flowchart for Serial Receiving (2)
In receiving, the SCI operates as follows:
• The SCI synchronizes with serial clock input or output and synchronizes internally.
• Receive data is stored in RSR in order from LSB to MSB.
After receiving the data, the SCI checks that the RDRF flag is 0, so that receive data can be
transferred from RSR to RDR. If this check passes, the RDRF flag is set to 1 and the received
data is stored in RDR. If the checks fails (receive error), the SCI operates as shown in table
13.11.
When a receive error has been identified in the error check, subsequent transmit and receive
operations are disabled.
• When the RDRF flag is set to 1, if the RIE bit is set to 1 in SCR, a receive-data-full interrupt
(RXI) is requested. If the ORER flag is set to 1 and the RIE bit in SCR is also set to 1, a
receive-error interrupt (ERI) is requested.
Rev. 3.00 Sep 14, 2005 page 522 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Figure 13.19 shows an example of SCI receive operation.
Serial clock
Serial data
Bit 7
Bit 0
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
RDRF
ORER
RXI interrupt
request
RXI interrupt handler
reads data in RDR and
clears RDRF flag to 0
RXI interrupt
request
Overrun error,
ERI interrupt
request
1 frame
Figure 13.19 Example of SCI Receive Operation
Rev. 3.00 Sep 14, 2005 page 523 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
• Transmitting and Receiving Data Simultaneously (Synchronous Mode): Figure 13.20 shows a
sample flowchart for transmitting and receiving serial data simultaneously and indicates the
procedure to follow.
Initialize
(1)
(1)
SCI initialization: the transmit data output function of the
TxD pin and the read data input function of the RxD pin
are selected, enabling simultaneous transmitting and
receiving.
(2)
SCI status check and transmit data write: read SSR, check
that the TDRE flag is 1, then write transmit data in TDR
and clear the TDRE flag to 0.
Notification that the TDRE flag has changed from 0 to 1
can also be given by the TXI interrupt.
(3)
Receive error handling: if a receive error occurs, read the
ORER flag in SSR, then after executing the necessary
error handling, clear the ORER flag to 0.
Neither transmitting nor receiving can resume while the
ORER flag remains set to 1.
(4)
SCI status check and receive data read: read SSR, check
that the RDRF flag is 1, then read receive data from RDR
and clear the RDRF flag to 0. Notification that the RDRF
flag has changed from 0 to 1 can also be given by the RXI
interrupt.
(5)
To continue transmitting and receiving serial data: check
the RDRF flag, read RDR, and clear the RDRF flag to 0
before the MSB (bit 7) of the current frame is received.
Also check that the TDRE flag is set to 1, indicating that
data can be written, write data in TDR, then clear the
TDRE flag to 0 before the MSB (bit 7) of the current frame
is transmitted. When the DMAC is activated by a transmitdata-empty interrupt request (TXI) to write data in TDR,
the TDRE flag is checked and cleared automatically.
When the DMAC is activated by a receive-data-full
interrupt request (RXI) to read RDR, the RDRF flag is
cleared automatically.
Start of transmitting and receiving
Read TDRE flag in SSR
No
(2)
TDRE = 1
Yes
Write transmit data in TDR and
clear TDRE flag to 0 in SSR
Read ORER flag in SSR
ORER = 1
Yes
(3)
No
Error handling
Read RDRF flag in SSR
No
(4)
RDRF = 1
Yes
Read receive data from RDR, and
clear RDRF flag to 0 in SSR
No
End of transmitting
and receiving?
(5)
Yes
Clear TE and RE bits to 0 in SCR
<End>
Note: When switching from transmitting or receiving to simultaneous transmitting and receiving, clear both the TE bit
and the RE bit to 0, then set both bits to 1 simultaneously.
Figure 13.20 Sample Flowchart for Simultaneous Serial Transmitting and Receiving
Rev. 3.00 Sep 14, 2005 page 524 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.4
SCI Interrupts
The SCI has four interrupt request sources: the transmit-end interrupt (TEI), receive-error
interrupt (ERI), receive-data-full interrupt (RXI), and transmit-data-empty interrupt (TXI). Table
13.12 lists the interrupt sources and indicates their priority. These interrupts can be enabled or
disabled by the TIE, RIE, and TEIE bits in SCR. Each interrupt request is sent separately to the
interrupt controller.
A TXI interrupt is requested when the TDRE flag is set to 1 in SSR. A TEI interrupt is requested
when the TEND flag is set to 1 in SSR. A TXI interrupt request can activate the DMAC to
transfer data. Data transfer by the DMAC automatically clears the TDRE flag to 0. A TEI
interrupt request cannot activate the DMAC.
An RXI interrupt is requested when the RDRF flag is set to 1 in SSR. An ERI interrupt is
requested when the ORER, PER, or FER flag is set to 1 in SSR. An RXI interrupt can activate the
DMAC to transfer data. Data transfer by the DMAC automatically clears the RDRF flag to 0. An
ERI interrupt request cannot activate the DMAC.
The DMAC can be activated by interrupts from SCI channel 0.
Table 13.12 SCI Interrupt Sources
Interrupt Source
Description
Priority
ERI
Receive error (ORER, FER, or PER)
High
RXI
Receive data register full (RDRF)
TXI
Transmit data register empty (TDRE)
TEI
Transmit end (TEND)
Low
Rev. 3.00 Sep 14, 2005 page 525 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
13.5
Usage Notes
13.5.1
Notes on Use of SCI
Note the following points when using the SCI.
TDR Write and TDRE Flag: The TDRE flag in SSR is a status flag indicating the loading of
transmit data from TDR to TSR. The SCI sets the TDRE flag to 1 when it transfers data from
TDR to TSR.
Data can be written into TDR regardless of the state of the TDRE flag. If new data is written in
TDR when the TDRE flag is 0, the old data stored in TDR will be lost because this data has not
yet been transferred to TSR. Before writing transmit data in TDR, be sure to check that the
TDRE flag is set to 1.
Simultaneous Multiple Receive Errors: Table 13.13 shows the state of the SSR status flags
when multiple receive errors occur simultaneously. When an overrun error occurs the RSR
contents are not transferred to RDR, so receive data is lost.
Table 13.13 SSR Status Flags and Transfer of Receive Data
Receive Data
Transfer
SSR Status Flags
RDRF
ORER
FER
PER
RSR → RDR
Receive Errors
1
1
0
0
×
Overrun error
0
0
1
0
Framing error
0
0
0
1
Parity error
1
1
1
0
×
Overrun error +
framing error
1
1
0
1
×
Overrun error +
parity error
0
0
1
1
1
1
1
1
Notes:
: Receive data is transferred from RSR to RDR.
× : Receive data is not transferred from RSR to RDR.
Rev. 3.00 Sep 14, 2005 page 526 of 910
REJ09B0258-0300
Framing error +
parity error
×
Overrun error +
framing error +
parity error
Section 13 Serial Communication Interface
Break Detection and Processing: Break signals can be detected by reading the RxD pin directly
when a framing error (FER) is detected. In the break state the input from the RxD pin consists of
all 0s, so the FER flag is set and the parity error flag (PER) may also be set. In the break state the
SCI receiver continues to operate, so if the FER flag is cleared to 0 it will be set to 1 again.
Sending a Break Signal: The input/output condition and level of the TxD pin are determined by
DR and DDR bits. This feature can be used to send a break signal.
After the serial transmitter is initialized, the DR value substitutes for the mark state until the TE
bit is set to 1 (the TxD pin function is not selected until the TE bit is set to 1). The DDR and DR
bits should therefore be set to 1 beforehand.
To send a break signal during serial transmission, clear the DR bit to 0 , then clear the TE bit to 0.
When the TE bit is cleared to 0 the transmitter is initialized, regardless of its current state, so the
TxD pin becomes an input/output outputting the value 0.
Receive Error Flags and Transmitter Operation (Synchronous Mode Only): When a receive
error flag (ORER, PER, or FER) is set to 1 the SCI will not start transmitting, even if the TDRE
flag is cleared to 0. Be sure to clear the receive error flags to 0 when starting to transmit. Note
that clearing the RE bit to 0 does not clear the receive error flags to 0.
Receive Data Sampling Timing in Asynchronous Mode and Receive Margin: In
asynchronous mode the SCI operates on a base clock with 16 times the bit rate frequency. In
receiving, the SCI synchronizes internally with the fall of the start bit, which it samples on the
base clock. Receive data is latched at the rising edge of the eighth base clock pulse. See figure
13.21.
Rev. 3.00 Sep 14, 2005 page 527 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
16 clocks
8 clocks
0
7
15 0
7
15 0
Internal base clock
Receive data
(RxD)
D0
Start bit
D1
Synchronization
sampling timing
Data sampling
timing
Figure 13.21 Receive Data Sampling Timing in Asynchronous Mode
The receive margin in asynchronous mode can therefore be expressed as shown in equation (1).
M=
1
2N
(0.5 –
) – (L – 0.5) F –
D – 0.5
N
(1 + F)
× 100%
. . . . . . . . (1)
M:
N:
D:
L:
F:
Receive margin (%)
Ratio of clock frequency to bit rate (N = 16)
Clock duty cycle (L = 0 to 1.0)
Frame length (L = 9 to 12)
Absolute deviation of clock frequency
From equation (1), if F = 0 and D = 0.5, the receive margin is 46.875%, as given by equation (2).
D = 0.5, F = 0
M = (0.5 –
1
2 × 16
) × 100%
= 46.875%
. . . . . . . . (2)
This is a theoretical value. A reasonable margin to allow in system designs is 20% to 30%.
Rev. 3.00 Sep 14, 2005 page 528 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Restrictions on Use of DMAC:
• When an external clock source is used for the serial clock, after the DMAC updates TDR,
allow an inversion of at least five system clock (φ) cycles before input of the serial clock to
start transmitting. If the serial clock is input within four states of the TDR update, a
malfunction may occur. (See figure 13.22)
• To have the DMAC read RDR, be sure to select the corresponding SCI receive-data-full
interrupt (RXI) as the activation source with bits DTS2 to DTS0 in DTCR.
SCK
t
TDRE
D0
D1
D2
D3
D4
D5
D6
D7
Note: In operation with an external clock source, be sure that t >4 states.
Figure 13.22 Example of Synchronous Transmission Using DMAC
Rev. 3.00 Sep 14, 2005 page 529 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Switching from SCK Pin Function to Port Pin Function:
• Problem in Operation: When switching the SCK pin function to the output port function (highlevel output) by making the following settings while DDR = 1, DR = 1, C/A = 1, CKE1 = 0,
CKE0 = 0, and TE = 1 (synchronous mode), low-level output occurs for one half-cycle.
1. End of serial data transmission
2. TE bit = 0
3. C/A bit = 0 ... switchover to port output
4. Occurrence of low-level output (see figure 13.23)
Half-cycle low-level output
SCK/port
1. End of transmission
Data
TE
Bit 6
4. Low-level output
Bit 7
2. TE= 0
C/A
3. C/A = 0
CKE1
CKE0
Figure 13.23 Operation when Switching from SCK Pin Function to Port Pin Function
Rev. 3.00 Sep 14, 2005 page 530 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
• Sample Procedure for Avoiding Low-Level Output: As this sample procedure temporarily
places the SCK pin in the input state, the SCK/port pin should be pulled up beforehand with
an external circuit.
With DDR = 1, DR = 1, C/A = 1, CKE1 = 0, CKE0 = 0, and TE = 1, make the following
settings in the order shown.
1. End of serial data transmission
2. TE bit = 0
3. CKE1 bit = 1
4. C/A bit = 0 ... switchover to port output
5. CKE1 bit = 0
High-level output TE
SCK/port
1. End of transmission
Data
TE
Bit 6
Bit 7
2. TE= 0
4. C/A = 0
C/A
3. CKE1= 1
CKE1
5. CKE1= 0
CKE0
Figure 13.24 Operation when Switching from SCK Pin Function to Port Pin Function
(Example of Preventing Low-Level Output)
Rev. 3.00 Sep 14, 2005 page 531 of 910
REJ09B0258-0300
Section 13 Serial Communication Interface
Rev. 3.00 Sep 14, 2005 page 532 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Section 14 Smart Card Interface
14.1
Overview
An IC card (smart card) interface conforming to the ISO/IEC 7816-3 (Identification Card)
standard is supported as an extension of the serial communication interface (SCI) functions.
Switchover between the normal serial communication interface and the smart card interface is
controlled by a register setting.
14.1.1
Features
Features of the smart card interface supported by the H8/3068F are listed below.
• Asynchronous communication
 Data length: 8 bits
 Parity bit generation and checking
 Transmission of error signal (parity error) in receive mode
 Error signal detection and automatic data retransmission in transmit mode
 Direct convention and inverse convention both supported
• Built-in baud rate generator allows any bit rate to be selected
• Three interrupt sources
 There are three interrupt sources—transmit-data-empty, receive-data-full, and
transmit/receive error—that can issue requests independently.
 The transmit-data-empty interrupt and receive-data-full interrupt can activate the DMA
controller (DMAC) to execute data transfer.
Rev. 3.00 Sep 14, 2005 page 533 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
14.1.2
Block Diagram
Bus interface
Figure 14.1 shows a block diagram of the smart card interface.
Module data bus
RxD
RDR
TDR
RSR
TSR
TxD
SCMR
SSR
SCR
SMR
Transmission/
reception
control
Parity generation
BRR
φ
Baud rate
generator
φ/4
φ/16
φ/64
Clock
Parity check
External clock
SCK
Legend
SCMR:
RSR:
RDR:
TSR:
TDR:
SMR:
SCR:
SSR:
BRR:
Smart card mode register
Receive shift register
Receive data register
Transmit shift register
Transmit data register
Serial mode register
Serial control register
Serial status register
Bit rate register
TXI
RXI
ERI
Figure 14.1 Block Diagram of Smart Card Interface
Rev. 3.00 Sep 14, 2005 page 534 of 910
REJ09B0258-0300
Internal
data bus
Section 14 Smart Card Interface
14.1.3
Pin Configuration
Table 14.1 shows the smart card interface pins.
Table 14.1 Smart Card Interface Pins
Pin Name
Abbreviation
I/O
Function
Serial clock pin
SCK
I/O
Clock input/output
Receive data pin
RxD
Input
Receive data input
Transmit data pin
TxD
Output
Transmit data output
Rev. 3.00 Sep 14, 2005 page 535 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
14.1.4
Register Configuration
The smart card interface has the internal registers listed in table 14.2. The BRR, TDR, and RDR
registers have their normal serial communication interface functions, as described in section 13,
Serial Communication Interface.
Table 14.2 Smart Card Interface Registers
Channel
Address*1 Name
Abbreviation
R/W
Initial Value
0
H'FFFB0
Serial mode register
SMR
R/W
H'00
H'FFFB1
Bit rate register
BRR
R/W
H'FF
H'FFFB2
Serial control register
SCR
R/W
H'00
H'FF
1
2
H'FFFB3
Transmit data register
TDR
R/W
H'FFFB4
Serial status register
SSR
R/(W)*2 H'84
H'FFFB5
Receive data register
RDR
R
H'00
H'FFFB6
Smart card mode register
SCMR
R/W
H'F2
H'FFFB8
Serial mode register
SMR
R/W
H'00
H'FFFB9
Bit rate register
BRR
R/W
H'FF
H'FFFBA
Serial control register
SCR
R/W
H'00
H'FFFBB
Transmit data register
TDR
R/W
H'FF
2
H'FFFBC
Serial status register
SSR
R/(W)*
H'84
H'FFFBD
Receive data register
RDR
R
H'00
H'FFFBE
Smart card mode register
SCMR
R/W
H'F2
H'FFFC0
Serial mode register
SMR
R/W
H'00
H'FFFC1
Bit rate register
BRR
R/W
H'FF
H'FFFC2
Serial control register
SCR
R/W
H'00
H'FFFC3
Transmit data register
TDR
R/W
H'FF
2
H'FFFC4
Serial status register
SSR
R/(W)*
H'FFFC5
Receive data register
RDR
R
H'00
H'FFFC6
Smart card mode register
SCMR
R/W
H'F2
Notes: 1. Lower 20 bits of the address in advanced mode.
2. Only 0 can be written in bits 7 to 3, to clear the flags.
Rev. 3.00 Sep 14, 2005 page 536 of 910
REJ09B0258-0300
H'84
Section 14 Smart Card Interface
14.2
Register Descriptions
This section describes the new or modified registers and bit functions in the smart card interface.
14.2.1
Smart Card Mode Register (SCMR)
SCMR is an 8-bit readable/writable register that selects smart card interface functions.
7
6
5
4
3
2
1
0
—
—
—
—
SDIR
SINV
—
SMIF
Initial value
1
1
1
1
0
0
1
0
Read/Write
—
—
—
—
R/W
R/W
—
R/W
Bit
Reserved bits
Reserved bit
Smart card interface
mode select
Enables or disables
the smart card interface
function
Smart card data invert
Inverts data logic levels
Smart card data transfer direction
Selects the serial/parallel conversion format
SCMR is initialized to H'F2 by a reset and in standby mode.
Bits 7 to 4—Reserved: Read-only bits, always read as 1.
Bit 3—Smart Card Data Transfer Direction (SDIR): Selects the serial/parallel conversion
format.*1
Bit 3
SDIR
Description
0
TDR contents are transmitted LSB-first
(Initial value)
Receive data is stored LSB-first in RDR
1
TDR contents are transmitted MSB-first
Receive data is stored MSB-first in RDR
Rev. 3.00 Sep 14, 2005 page 537 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Bit 2—Smart Card Data Invert (SINV): Specifies inversion of the data logic level. This
function is used in combination with the SDIR bit to communicate with inverse-convention
cards.*2 The SINV bit does not affect the logic level of the parity bit. For parity settings, see
section 14.3.4, Register Settings.
Bit 2
SINV
Description
0
Unmodified TDR contents are transmitted
(Initial value)
Receive data is stored unmodified in RDR
1
Inverted TDR contents are transmitted
Receive data is inverted before storage in RDR
Bit 1—Reserved: Read-only bit, always read as 1.
Bit 0—Smart Card Interface Mode Select (SMIF): Enables the smart card interface function.
Bit 0
SMIF
Description
0
Smart card interface function is disabled
1
Smart card interface function is enabled
(Initial value)
Notes: 1. The function for switching between LSB-first and MSB-first mode can also be used
with the normal serial communication interface. Note that when the communication
format data length is set to 7 bits and MSB-first mode is selected for the serial data to
be transferred, bit 0 of TDR is not transmitted, and only bits 7 to 1 of the received data
are valid.
2. The data logic level inversion function can also be used with the normal serial
communication interface. Note that, when inverting the serial data to be transferred,
parity transmission and parity checking is based on the number of high-level periods at
the serial data I/O pin, and not on the register value.
Rev. 3.00 Sep 14, 2005 page 538 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
14.2.2
Serial Status Register (SSR)
The function of SSR bit 4 is modified in smart card interface mode. This change also causes a
modification to the setting conditions for bit 2 (TEND).
Bit
7
6
5
4
3
2
1
0
TDRE
RDRF
ORER
ERS
PER
TEND
MPB
MPBT
Initial value
1
0
0
0
0
1
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R
R
R/W
Transmit end
Status flag indicating end
of transmission
Error signal status (ERS)
Status flag indicating that an error
signal has been received
Note: * Only 0 can be written, to clear the flag.
Bits 7 to 5: These bits operate as in normal serial communication. For details see section 13.2.7,
Serial Status Register (SSR).
Bit 4—Error Signal Status (ERS): In smart card interface mode, this flag indicates the status of
the error signal sent from the receiving device to the transmitting device. The smart card interface
does not detection framing errors.
Bit 4
ERS
Description
0
Indicates normal transmission, with no error signal returned
(Initial value)
[Clearing conditions]
The chip is reset, or enters standby mode or module stop mode
Software reads ERS while it is set to 1, then writes 0.
1
Indicates that the receiving device sent an error signal reporting a parity error
[Setting condition]
A low error signal was sampled.
Note: Clearing the TE bit to 0 in SCR does not affect the ERS flag, which retains its previous
value.
Rev. 3.00 Sep 14, 2005 page 539 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Bits 3 to 0: These bits operate as in normal serial communication. For details see section 13.2.7,
Serial Status Register (SSR). The setting conditions for transmit end (TEND), however, are
modified as follows.
Bit 2
TEND
Description
0
Transmission is in progress
[Clearing conditions]
Software reads TDRE while it is set to 1, then writes 0 in the TDRE flag.
The DMAC or DTC writes data in TDR.
1
End of transmission
[Setting conditions]
(Initial value)
The chip is reset or enters standby mode.
The TE bit and FER/ERS bit are both cleared to 0 in SCR.
TDRE is 1 and FER/ERS is 0 at a time 2.5 etu after the last bit of a 1-byte serial
character is transmitted (normal transmission).
Note: etu (Elementary time unit: the time for transfer of one bit)
14.2.3
Serial Mode Register (SMR)
The function of SMR bit 7 is modified in smart card interface mode. This change also causes a
modification to the function of bits 1 and 0 in the serial control register (SCR).
7
6
5
4
3
2
1
0
GM
CHR
PE
O/E
STOP
MP
CKS1
CKS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Rev. 3.00 Sep 14, 2005 page 540 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Bit 7—GSM Mode (GM): With the normal smart card interface, this bit is cleared to 0. Setting
this bit to 1 selects GSM mode, an additional mode for controlling the timing for setting the
TEND flag that indicates completion of transmission, and the type of clock output used. The
details of the additional clock output control mode are specified by the CKE1 and CKE0 bits in
the serial control register (SCR).
Bit 7
GM
Description
0
Normal smart card interface mode operation
The TEND flag is set 12.5 etu after the beginning of the start bit.
Clock output on/off control only.
1
(Initial value)
GSM mode smart card interface mode operation
The TEND flag is set 11.0 etu after the beginning of the start bit.
Clock output on/off and fixed-high/fixed-low control.
Note: etu (Elementary time unit: the time for transfer of one bit)
Bits 6 to 0: These bits operate as in normal serial communication. For details see section 13.2.5,
Serial Mode Register (SMR).
14.2.4
Serial Control Register (SCR)
The function of SCR bits 1 and 0 is modified in smart card interface mode
7
6
5
4
3
2
1
0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Bits 7 to 2: These bits operate as in normal serial communication. For details see section 13.2.6,
Serial Control Register (SCR).
Bits 1 and 0—Clock Enable 1 and 0 (CKE1, CKE0): These bits select the SCI clock source
and enable or disable clock output from the SCK pin. In smart card interface mode, it is possible
to specify a fixed high level or fixed low level for the clock output, in addition to the usual
switching between enabling and disabling of the clock output.
Rev. 3.00 Sep 14, 2005 page 541 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Bit 7
GM
Bit 1
CKE1
Bit 0
CKE0
Description
0
0
0
Internal clock/SCK pin is I/O port
1
Internal clock/SCK pin is clock output
0
Internal clock/SCK pin is fixed at low output
1
Internal clock/SCK pin is clock output
0
Internal clock/SCK pin is fixed at high output
1
Internal clock/SCK pin is clock output
1
1
14.3
Operation
14.3.1
Overview
(Initial value)
The main features of the smart card interface are as follows.
• One frame consists of 8-bit data plus a parity bit.
• In transmission, a guard time of at least 2 etu (elementary time units: the time for transfer of
one bit) is provided between the end of the parity bit and the start of the next frame.
• If a parity error is detected during reception, a low error signal level is output for a1 etu period
10.5 etu after the start bit.
• If an error signal is detected during transmission, the same data is transmitted automatically
after the elapse of 2 etu or longer.
• Only asynchronous communication is supported; there is no synchronous communication
function.
14.3.2
Pin Connections
Figure 14.2 shows a pin connection diagram for the smart card interface.
In communication with a smart card, since both transmission and reception are carried out on a
single data transmission line, the TxD pin and RxD pin should both be connected to this line. The
data transmission line should be pulled up to VCC with a resistor.
When the smart card uses the clock generated on the smart card interface, the SCK pin output is
input to the CLK pin of the smart card. If the smart card uses an internal clock, this connection is
unnecessary.
The reset signal should be output from one of the H8/3068F’s generic ports.
Rev. 3.00 Sep 14, 2005 page 542 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
In addition to these pin connections, power and ground connections will normally also be
necessary.
VCC
TxD
RxD
I/O
Data line
SCK
H8/3068F
chip
Clock line
Px (port)
Reset line
CLK
RST
Smart card
Card-processing device
Figure 14.2 Smart Card Interface Connection Diagram
Note: A loop-back test can be performed by setting both RE and TE to 1 without connecting a
smart card.
Rev. 3.00 Sep 14, 2005 page 543 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
14.3.3
Data Format
Figure 14.3 shows the smart card interface data format. In reception in this mode, a parity check
is carried out on each frame, and if an error is detected an error signal is sent back to the
transmitting device to request retransmission of the data. In transmission, the error signal is
sampled and the same data is retransmitted if the error signal is low.
No parity error
Ds
D0
D1
D2
D3
D4
D5
D6
D7
Dp
D7
Dp
Output from transmitting device
Parity error
Ds
D0
D1
D2
D3
D4
D5
D6
DE
Output from transmitting device
Legend
Ds:
D0 to D7:
Dp:
DE:
Start bit
Data bits
Parity bit
Error signal
Output from
receiving
device
Figure 14.3 Smart Card Interface Data Format
The operating sequence is as follows.
1. When the data line is not in use it is in the high-impedance state, and is fixed high with a pullup resistor.
2. The transmitting device starts transfer of one frame of data. The data frame starts with a start
bit (Ds, low-level), followed by 8 data bits (D0 to D7) and a parity bit (Dp).
3. With the smart card interface, the data line then returns to the high-impedance state. The data
line is pulled high with a pull-up resistor.
4. The receiving device carries out a parity check. If there is no parity error and the data is
received normally, the receiving device waits for reception of the next data. If a parity error
occurs, however, the receiving device outputs an error signal (DE, low-level) to request
Rev. 3.00 Sep 14, 2005 page 544 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
retransmission of the data. After outputting the error signal for the prescribed length of time,
the receiving device places the signal line in the high-impedance state again. The signal line is
pulled high again by a pull-up resistor.
5. If the transmitting device does not receive an error signal, it proceeds to transmit the next data
frame. If it receives an error signal, however, it returns to step 2 and transmits the same data
again.
14.3.4
Register Settings
Table 14.3 shows a bit map of the registers used in the smart card interface. Bits indicated as 0 or
1 must be set to the value shown. The setting of other bits is described in this section.
Table 14.3 Smart Card Interface Register Settings
Bit
1
Register Address*
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SMR
H'FFFB0
GM
0
1
O/E
1
0
CKS1
CKS0
BRR
H'FFFB1
BRR7
BRR6
BRR5
BRR4
BRR3
BRR2
BRR1
BRR0
2
SCR
H'FFFB2
TIE
RIE
TE
RE
0
0
CKE1*
CKE0
TDR
H'FFFB3
TDR7
TDR6
TDR5
TDR4
TDR3
TDR2
TDR1
TDR0
SSR
H'FFFB4
TDRE
RDRF
ORER
ERS
PER
TEND
0
0
RDR
H'FFFB5
RDR7
RDR6
RDR5
RDR4
RDR3
RDR2
RDR1
RDR0
SCMR
H'FFFB6
—
—
—
—
SDIR
SINV
—
SMIF
Notes: — Unused bit.
1. Lower 20 bits of the address in advanced mode.
2. When GM is cleared to 0 in SMR, the CKE1 bit must also be cleared to 0.
Serial Mode Register (SMR) Settings: Clear the GM bit to 0 when using the normal smart card
interface mode, or set to 1 when using GSM mode. Clear the O/E bit to 0 if the smart card is of
the direct convention type, or set to 1 if of the inverse convention type.
Bits CKS1 and CKS0 select the clock source of the built-in baud rate generator. See section
14.3.5, Clock.
Bit Rate Register (BRR) Settings: BRR is used to set the bit rate. See section 14.3.5, Clock, for
the method of calculating the value to be set.
Serial Control Register (SCR) Settings: The TIE, RIE, TE, and RE bits have their normal serial
communication functions. See section 13, Serial Communication Interface, for details. The CKE1
and CKE0 bits specify clock output. To disable clock output, clear these bits to 00; to enable
Rev. 3.00 Sep 14, 2005 page 545 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
clock output, set these bits to 01. Clock output is not performed when the GM bit is set to 1 in
SMR. Clock output can also be fixed low or high.
Smart Card Mode Register (SCMR) Settings: Clear both the SDIR bit and SINV bit cleared to
0 if the smart card is of the direct convention type, and set both to 1 if of the inverse convention
type. To use the smart card interface, set the SMIF bit to 1.
The register settings and examples of starting character waveforms are shown below for two
smart cards, one following the direct convention and one the inverse convention.
1. Direct Convention (SDIR = SINV = O/E = 0)
(Z)
A
Z
Z
A
Z
Z
Z
A
A
Z
Ds
D0
D1
D2
D3
D4
D5
D6
D7
Dp
(Z)
State
With the direct convention type, the logic 0 level corresponds to state Z and the logic 1 level
to state A, and transfer is performed in LSB-first order. In the example above, the first
character data is H'3B. The parity bit is 1, following the even parity rule designated for smart
cards.
2. Indirect Convention (SDIR = SINV = O/E = 1)
(Z)
A
Z
Z
A
A
A
A
A
A
Z
Ds
D7
D6
D5
D4
D3
D2
D1
D0
Dp
(Z)
State
With the indirect convention type, the logic 1 level corresponds to state Z and the logic 0 level
to state A, and transfer is performed in MSB-first order. In the example above, the first
character data is H'3F. The parity bit is 0, corresponding to state Z, following the even parity
rule designated for smart cards.
In the H8/3068F, inversion specified by the SINV bit applies only to the data bits, D7 to D0.
For parity bit inversion, the O/E bit in SMR must be set to odd parity mode. This applies to
both transmission and reception.
Rev. 3.00 Sep 14, 2005 page 546 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
14.3.5
Clock
Only an internal clock generated by the on-chip baud rate generator can be used as the
transmit/receive clock for the smart card interface. The bit rate is set with the bit rate register
(BRR) and the CKS1 and CKS0 bits in the serial mode register (SMR). The equation for
calculating the bit rate is shown below. Table 14.5 shows some sample bit rates.
If clock output is selected with CKE0 set to 1, a clock with a frequency of 372 times the bit rate is
output from the SCK pin.
B=
φ
× 106
1488 × 22n–1 × (N + 1)
where, N: BRR setting (0 ≤ N ≤ 255)
B: Bit rate (bit/s)
φ: Operating frequency (MHz)
n: See table 14.4
Table 14.4 n-Values of CKS1 and CKS0 Settings
n
CKS1
CKS0
0
0
0
1
2
1
1
0
3
1
Note: * If the gear function is used to divide the clock frequency, use the divided frequency to
calculate the bit rate. The equation above applies directly to 1/1 frequency division.
Table 14.5 Bit Rates (bits/s) for Various BRR Settings (When n = 0)
φ (MHz)
N
7.1424
10.00
10.7136
13.00
14.2848
16.00
18.00
0
9600.0
13440.9
14400.0
17473.1
19200.0
21505.4
24193.5
1
4800.0
6720.4
7200.0
8736.6
9600.0
10752.7
12096.8
2
3200.0
4480.3
4800.0
5824.4
6400.0
7168.5
8064.5
Note: Bit rates are rounded off to one decimal place.
Rev. 3.00 Sep 14, 2005 page 547 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
The following equation calculates the bit rate register (BRR) setting from the operating frequency
and bit rate. N is an integer from 0 to 255, specifying the value with the smaller error.
N=
φ
1488 × 22n–1 × B
× 106 – 1
Table 14.6 BRR Settings for Typical Bit Rates (bits/s) (When n = 0)
φ (MHz)
7.1424
10.00
10.7136
13.00
14.2848
16.00
18.00
bit/s
N
Error
N
Error
N
Error
N
Error
N
Error
N
Error
N
Error
9600
0
0.00
1
30
1
25
1
8.99
1
0.00
1
12.01
2
15.99
Table 14.7 Maximum Bit Rates for Various Frequencies (Smart Card Interface Mode)
φ (MHz)
Maximum Bit Rate (bits/s)
N
n
7.1424
9600
0
0
10.00
13441
0
0
10.7136
14400
0
0
13.00
17473
0
0
14.2848
19200
0
0
16.00
21505
0
0
18.00
24194
0
0
The bit rate error is given by the following equation:
Error (%) =
φ
1488 ×
22n-1
× B × (N + 1)
Rev. 3.00 Sep 14, 2005 page 548 of 910
REJ09B0258-0300
× 106 – 1
× 100
Section 14 Smart Card Interface
14.3.6
Transmitting and Receiving Data
Initialization: Before transmitting or receiving data, the smart card interface must be initialized
as described below. Initialization is also necessary when switching from transmit mode to receive
mode, or vice versa.
1. Clear the TE and RE bits to 0 in the serial control register (SCR).
2. Clear error flags FER/ERS, PER, and ORER to 0 in the serial status register (SSR).
3. Set the parity bit (O/E) and baud rate generator select bits (CKS1 and CKS0) in the serial
mode register (SMR). Clear the C/A, CHR, and MP bits to 0, and set the STOP and PE bits to
1.
4. Set the SMIF, SDIR, and SINV bits in the smart card mode register (SCMR).
When the SMIF bit is set to 1, the TxD pin and RxD pin are both switched from port to SCI pin
functions and go to the high-impedance state.
5. Set a value corresponding to the desired bit rate in the bit rate register (BRR).
6. Set the CKE0 bit in SCR. Clear the TIE, RIE, TE, RE, MPIE, TEIE, and CKE1 bits to 0. If
the CKE0 bit is set to 1, the clock is output from the SCK pin.
7. Wait at least one bit interval, then set the TIE, RIE, TE, and RE bits in SCR. Do not set the
TE bit and RE bit at the same time, except for self-diagnosis.
Transmitting Serial Data: As data transmission in smart card mode involves error signal
sampling and retransmission processing, the processing procedure is different from that for the
normal SCI. Figure 14.5 shows a sample transmission processing flowchart.
1.
2.
3.
4.
Perform smart card interface mode initialization as described in Initialization above.
Check that the FER/ERS error flag is cleared to 0 in SSR.
Repeat steps 2 and 3 until it can be confirmed that the TEND flag is set to 1 in SSR.
Write the transmit data in TDR, clear the TDRE flag to 0, and perform the transmit operation.
The TEND flag is cleared to 0.
5. To continue transmitting data, go back to step 2.
6. To end transmission, clear the TE bit to 0.
The above processing may include interrupt handling DMA transfer.
If transmission ends and the TEND flag is set to 1 while the TIE bit is set to 1 and interrupt
requests are enabled, a transmit-data-empty interrupt (TXI) will be requested. If an error occurs in
transmission and the ERS flag is set to 1 while the RIE bit is set to 1 and interrupt requests are
enabled, a transmit/receive-error interrupt (ERI) will be requested.
The timing of TEND flag setting depends on the GM bit in SMR (see figure 14.4).
Rev. 3.00 Sep 14, 2005 page 549 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
If the TXI interrupt activates the DMAC, the number of bytes designated in the DMAC can be
transmitted automatically, including automatic retransmission.
For details, see Interrupt Operations and Data Transfer by DMAC in this section.
Serial data
Dp
Ds
DE
Guard time
(1) GM = 0
TEND
12.5 etu
(2) GM = 1
TEND
11.0 etu
Note: etu (Elementary time unit: the time for transfer of one bit)
Figure 14.4 Timing of TEND Flag Setting
Rev. 3.00 Sep 14, 2005 page 550 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Start
Initialization
Start transmitting
No
FER/ERS = 0?
Yes
Error handling
No
TEND = 1?
Yes
Write transmit data in TDR,
and clear TDRE flag
to 0 in SSR
No
All data transmitted?
Yes
No
FER/ERS = 0?
Yes
Error handling
No
TEND = 1?
Yes
Clear TE bit to 0
End
Figure 14.5 Sample Transmission Processing Flowchart
Rev. 3.00 Sep 14, 2005 page 551 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
TSR
(shift register)
TDR
1. Data write
Data 1
2. Transfer from TDR to TSR
Data 1
3. Serial data output
Data 1
Data 1
Data remains in TDR
Data 1
I/O signal
output
In case of normal transmission: TEND flag is set
In case of transmit error:
ERS flag is set
Steps 2 and 3 above are repeated until the
TEND flag is set.
Note: When the ERS flag is set, it should be cleared until transfer of the last bit (D7 in LSB-first
transmission, D0 in MSB-first transmission) of the retransmit data to be transmitted next has
been completed.
Figure 14.6 Relation Between Transmit Operation and Internal Registers
I/O data
Ds
Da
Db
Dc
Dd
De
Df
Dg
Dh
Dp
DE
Guard time
TXI (TEND
interrupt)
12.5 etu
11.0 etu
When GM = 0
When GM = 1
Note: etu (Elementary time unit: the time for transfer of one bit)
Figure 14.7 Timing of TEND Flag Setting
Receiving Serial Data: Data reception in smart card mode uses the same processing procedure
as for the normal SCI. Figure 14.8 shows a sample reception processing flowchart.
1. Perform smart card interface mode initialization as described in Initialization above.
2. Check that the ORER flag and PER flag are cleared to 0 in SSR. If either is set, perform the
appropriate receive error handling, then clear both the ORER and the PER flag to 0.
3. Repeat steps 2 and 3 until it can be confirmed that the RDRF flag is set to 1.
4. Read the receive data from RDR.
Rev. 3.00 Sep 14, 2005 page 552 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
5. To continue receiving data, clear the RDRF flag to 0 and go back to step 2.
6. To end reception, clear the RE bit to 0.
Start
Initialization
Start receiving
ORER = 0
and PER = 0?
No
Yes
Error handling
No
RDRF = 1?
Yes
Read RDR and clear
RDRF flag to 0 in SSR
No
All data received?
Yes
Clear RE bit to 0
Figure 14.8 Sample Reception Processing Flowchart
The above procedure may include interrupt handling and DMA transfer.
If reception ends and the RDRF flag is set to 1 while the RIE bit is set to 1 and interrupt requests
are enabled, a receive-data-full interrupt (RXI) will be requested. If an error occurs in reception
and either the ORER flag or the PER flag is set to 1, a transmit/receive-error interrupt (ERI) will
be requested.
If the RXI interrupt activates the DMAC, the number of bytes designated in the DMAC will be
transferred, skipping receive data in which an error occurred.
Rev. 3.00 Sep 14, 2005 page 553 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
For details, see Interrupt Operations and Data Transfer by DMAC in this section.
If a parity error occurs during reception and the PER flag is set to 1, the received data is
transferred to RDR, so the erroneous data can be read.
Switching Modes: When switching from receive mode to transmit mode, first confirm that the
receive operation has been completed, then start from initialization, clearing RE to 0 and setting
TE to 1. The RDRF, PER, or ORER flag can be used to check that the receive operation has been
completed.
When switching from transmit mode to receive mode, first confirm that the transmit operation has
been completed, then start from initialization, clearing TE to 0 and setting RE to 1. The TEND
flag can be used to check that the transmit operation has been completed.
Fixing Clock Output: When the GM bit is set to 1 in SMR, clock output can be fixed by means
of the CKE1 and CKE0 bits in SCR. The minimum clock pulse width can be set to the specified
width in this case.
Figure 14.9 shows the timing for fixing clock output. In this example, GM = 1, CKE1 = 0, and the
CKE0 bit is controlled.
Specified pulse
width
Specified pulse
width
CKE1 value
SCK
SCR write
(CKE0 = 0)
SCR write
(CKE0 = 1)
Figure 14.9 Timing for Fixing Cock Output
Interrupt Operations: The smart card interface has three interrupt sources: transmit-data-empty
(TXI), transmit/receive-error (ERI), and receive-data-full (RXI). The transmit-end interrupt
request (TEI) is not available in smart card mode.
A TXI interrupt is requested when the TEND flag is set to 1 in SSR. An RXI interrupt is
requested when the RDRF flag is set to 1 in SSR. An ERI interrupt is requested when the ORER,
PER, or ERS flag is set to 1 in SSR. These relationships are shown in table 14.8.
Rev. 3.00 Sep 14, 2005 page 554 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Table 14.8 Smart Card Interface Mode Operating States and Interrupt Sources
Operating State
Transmit Mode
Receive Mode
Normal
operation
Flag
Enable Bit
Interrupt
Source
DMAC
Activation
TEND
TIE
TXI
Available
Error
ERS
RIE
ERI
Not available
Normal
operation
RDRF
RIE
RXI
Available
Error
PER, ORER
RIE
ERI
Not available
Data Transfer by DMAC: The DMAC can be used to transmit and receive data in smart card
mode, as in normal SCI operations. In transmit mode, when the TEND flag is set to 1 in SSR, the
TDRE flag is set simultaneously, generating a TXI interrupt. If the TXI request is designated
beforehand as a DMAC activation source, the DMAC will be activated by the TXI request and
will transfer the next transmit data. This data transfer by the DMAC automatically clears the
TDRE and TEND flags to 0. In the event of an error, the SCI automatically retransmits the same
data, keeping the TEND flag cleared to 0 so that the DMAC is not activated. The SCI and DMAC
will therefore automatically transmit the designated number of bytes, including retransmission
when an error occurs. When an error occurs, the ERS flag is not cleared automatically, so the RIE
bit should be set to 1 to enable the error to generate an ERI request, and the ERI interrupt handler
should clear ERS.
When using the DMAC to transmit or receive, first set up and enable the DMAC, then make SCI
settings. DMAC settings are described in section 7, DMA controller.
In receive operations, an RXI interrupt is requested when the RDRF flag is set to 1 in SSR. If the
RXI request is designated beforehand as a DMAC activation source, the DMAC will be activated
by the RXI request and will transfer the received data. This data transfer by the DMAC
automatically clears the RDRF flag to 0. When an error occurs, the RDRF flag is not set and an
error flag is set instead. The DMAC is not activated. The ERI interrupt request is directed to the
CPU. The ERI interrupt handler should clear the error flags.
Rev. 3.00 Sep 14, 2005 page 555 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Examples of Operation in GSM Mode: When switching between smart card interface mode
and software standby mode, use the following procedures to maintain the clock duty cycle.
• Switching from smart card interface mode to software standby mode
1. Set the P94 data register (DR) and data direction register (DDR) to the values for the fixed
output state in software standby mode.
2. Write 0 in the TE and RE bits in the serial control register (SCR) to stop transmit/receive
operations. At the same time, set the CKE1 bit to the value for the fixed output state in
software standby mode.
3. Write 0 in the CKE0 bit in SCR to stop the clock.
4. Wait for one serial clock cycle. During this period, the duty cycle is preserved and clock
output is fixed at the specified level.
5. Write H'00 in the serial mode register (SMR) and smart card mode register (SCMR).
6. Make the transition to the software standby state.
• Returning from software standby mode to smart card interface mode
1. Clear the software standby state.
2. Set the CKE1 bit in SCR to the value for the fixed output state at the start of software standby
(the current P94 pin state).
3. Set smart card interface mode and output the clock. Clock signal generation is started with the
normal duty cycle.
Software
standby
Normal operation
(1) (2) (3)
(4) (5) (6)
Normal operation
(1) (2) (3)
Figure 14.10 Procedure for Stopping and Restarting the Clock
Use the following procedure to secure the clock duty cycle after powering on.
1. The initial state is port input and high impedance. Use pull-up or pull-down resistors to fix the
potential.
2. Fix at the output specified by the CKE1 bit in SCR.
3. Set SMR and SCMR, and switch to smart card interface mode operation.
4. Set the CKE0 bit to 1 in SCR to start clock output.
Rev. 3.00 Sep 14, 2005 page 556 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
14.4
Usage Notes
The following points should be noted when using the SCI as a smart card interface.
Receive Data Sampling Timing and Receive Margin in Smart Card Interface Mode: In
smart card interface mode, the SCI operates on a base clock with a frequency of 372 times the
transfer rate. In reception, the SCI synchronizes internally with the fall of the start bit, which it
samples on the base clock. Receive data is latched at the rising edge of the 186th base clock pulse.
The timing is shown in figure 14.11.
372 clocks
186 clocks
0
185
185
371 0
371 0
Internal base
clock
Receive data
(RxD)
Start bit
D0
D1
Synchronization
sampling timing
Data sampling
timing
Figure 14.11 Receive Data Sampling Timing in Smart Card Interface Mode
Rev. 3.00 Sep 14, 2005 page 557 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
The receive margin can therefore be expressed as follows.
Receive margin in smart card interface mode:
M = (0.5 –
1
) – (L – 0.5) F –
2N
M:
N:
D:
L:
F:
D – 0.5
(1 + F) × 100%
N
Receive margin (%)
Ratio of clock frequency to bit rate (N = 372)
Clock duty cycle (L = 0 to 1.0)
Frame length (L =10)
Absolute deviation of clock frequency
From the above equation, if F = 0 and D = 0.5, the receive margin is as follows.
When D = 0.5 and F = 0:
M = (0.5 – 1/2 × 372) × 100%
= 49.866%
Retransmission: Retransmission is performed by the SCI in receive mode and transmit mode as
described below.
• Retransmission when SCI is in Receive Mode
Figure 14.12 illustrates retransmission when the SCI is in receive mode.
1. If an error is found when the received parity bit is checked, the PER bit is automatically set to
1. If the RIE bit in SCR is set to the enable state, an ERI interrupt is requested. The PER bit
should be cleared to 0 in SSR before the next parity bit sampling timing.
2. The RDRF bit in SSR is not set for the frame in which the error has occurred.
3. If no error is found when the received parity bit is checked, the PER bit is not set to 1 in SSR.
4. If no error is found when the received parity bit is checked, the receive operation is assumed
to have been completed normally, and the RDRF bit is automatically set to 1 in SSR. If the
RIE bit in SCR is set to the enable state, an RXI interrupt is requested. If RXI is enabled as a
DMA transfer activation source, the RDR contents can be read automatically. When the
DMAC reads the RDR data, the RDRF flag is automatically cleared to 0.
5. When a normal frame is received, the data pin is held in the high-impedance state at the error
signal transmission timing.
Rev. 3.00 Sep 14, 2005 page 558 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Frame n
Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp
Frame n+1
Retransmitted frame
DE
Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp
(DE)
Ds D0 D1 D2 D3 D4
RDRF
[2]
[4]
[1]
[3]
PER
Figure 14.12 Retransmission in SCI Receive Mode
• Retransmission when SCI is in Transmit Mode
Figure 14.13 illustrates retransmission when the SCI is in transmit mode.
6. If an error signal is sent back from the receiving device after transmission of one frame is
completed, the FER/ERS bit is set to 1 in SSR. If the RIE bit in SCR is set to the enable state,
an ERI interrupt is requested. The ERS bit should be cleared to 0 in SSR before the next parity
bit sampling timing.
7. The TEND bit in SSR is not set for the frame for which the error signal was received.
8. If an error signal is not sent back from the receiving device, the ERS flag is not set in SSR.
9. If an error signal is not sent back from the receiving device, transmission of one frame,
including retransmission, is assumed to have been completed, and the TEND bit is set to 1 in
SSR. If the TIE bit in SCR is set to the enable state, a TXI interrupt is requested. If TXI is
enabled as a DMA transfer activation source, the next data can be written in TDR
automatically. When the DMAC writes data in TDR, the TDRE bit is automatically cleared to
0.
Frame n
Frame n+1
Retransmitted frame
Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp DE
Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp
(DE)
Ds D0 D1 D2 D3 D4
TDRE
Transfer from TDR to TSR
Transfer from TDR to TSR
Transfer from TDR to TSR
TEND
[7]
[9]
ERS
[6]
[8]
Figure 14.13 Retransmission in SCI Transmit Mode
Rev. 3.00 Sep 14, 2005 page 559 of 910
REJ09B0258-0300
Section 14 Smart Card Interface
Rev. 3.00 Sep 14, 2005 page 560 of 910
REJ09B0258-0300
Section 15 A/D Converter
Section 15 A/D Converter
15.1
Overview
The H8/3068F includes a 10-bit successive-approximations A/D converter with a selection of up
to eight analog input channels.
When the A/D converter is not used, it can be halted independently to conserve power. For details
see section 20.6, Module Standby Function.
15.1.1
Features
A/D converter features are listed below.
• 10-bit resolution
• Eight input channels
• Selectable analog conversion voltage range
The analog voltage conversion range can be programmed by input of an analog reference
voltage at the VREF pin.
• High-speed conversion
Conversion time: maximum 3.5 µs per channel (with 20 MHz system clock)
• Two conversion modes
Single mode: A/D conversion of one channel
Scan mode: continuous conversion on one to four channels
• Four 16-bit data registers
A/D conversion results are transferred for storage into data registers corresponding to the
channels.
• Sample-and-hold function
• Three conversion start sources
The A/D converter can be activated by software, an external trigger, or an 8-bit timer compare
match.
• A/D interrupt requested at end of conversion
At the end of A/D conversion, an A/D end interrupt (ADI) can be requested.
• DMA controller (DMAC) activation
The DMAC can be activated at the end of A/D conversion.
Rev. 3.00 Sep 14, 2005 page 561 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.1.2
Block Diagram
Figure 15.1 shows a block diagram of the A/D converter.
Internal
data bus
AVSS
AN 0
ADCR
ADCSR
ADDRD
–
AN 2
AN 4
ADDRC
+
AN 1
AN 3
ADDRB
10-bit D/A
ADDRA
VREF
Successiveapproximations register
AVCC
Bus interface
Module data bus
Analog
multiplexer
AN 5
ø/4
Comparator
Control circuit
Sample-andhold circuit
ø/8
AN 6
AN 7
ADI
interrupt signal
ADTRG
Compare match A0
ADTE
8-bit timer TCSR0
Legend
ADCR:
ADCSR:
ADDRA:
ADDRB:
ADDRC:
ADDRD:
A/D control register
A/D control/status register
A/D data register A
A/D data register B
A/D data register C
A/D data register D
Figure 15.1 A/D Converter Block Diagram
Rev. 3.00 Sep 14, 2005 page 562 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.1.3
Input Pins
Table 15.1 summarizes the A/D converter’s input pins. The eight analog input pins are divided
into two groups: group 0 (AN0 to AN3), and group 1 (AN4 to AN7). AVCC and AVSS are the power
supply for the analog circuits in the A/D converter. VREF is the A/D conversion reference voltage.
Table 15.1 A/D Converter Pins
Pin Name
Abbreviation
I/O
Function
Analog power supply pin
AVCC
Input
Analog power supply
Analog ground pin
AVSS
Input
Analog ground and reference voltage
Reference voltage pin
VREF
Input
Analog reference voltage
Analog input pin 0
AN0
Input
Group 0 analog inputs
Analog input pin 1
AN1
Input
Analog input pin 2
AN2
Input
Analog input pin 3
AN3
Input
Analog input pin 4
AN4
Input
Analog input pin 5
AN5
Input
Analog input pin 6
AN6
Input
Analog input pin 7
AN7
Input
A/D external trigger input pin
ADTRG
Input
Group 1 analog inputs
External trigger input for starting A/D conversion
Rev. 3.00 Sep 14, 2005 page 563 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.1.4
Register Configuration
Table 15.2 summarizes the A/D converter’s registers.
Table 15.2 A/D Converter Registers
Address*1
Name
Abbreviation
R/W
Initial Value
H'FFFE0
A/D data register A H
ADDRAH
R
H'00
H'FFFE1
A/D data register A L
ADDRAL
R
H'00
H'FFFE2
A/D data register B H
ADDRBH
R
H'00
H'FFFE3
A/D data register B L
ADDRBL
R
H'00
H'FFFE4
A/D data register C H
ADDRCH
R
H'00
H'FFFE5
A/D data register C L
ADDRCL
R
H'00
H'FFFE6
A/D data register D H
ADDRDH
R
H'00
H'FFFE7
A/D data register D L
ADDRDL
R
H'00
2
H'FFFE8
A/D control/status register
ADCSR
R/(W)*
H'00
H'FFFE9
A/D control register
ADCR
R/W
H'7E
Notes: 1. Lower 20 bits of the address in advanced mode.
2. Only 0 can be written in bit 7, to clear the flag.
Rev. 3.00 Sep 14, 2005 page 564 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.2
Register Descriptions
15.2.1
A/D Data Registers A to D (ADDRA to ADDRD)
ADDRn
14
12
10
8
6
5
4
3
2
1
0
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 —
—
—
—
—
—
15
Bit
13
11
9
7
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
(n = A to D)
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A/D conversion data
10-bit data giving an
A/D conversion result
Reserved bits
The four A/D data registers (ADDRA to ADDRD) are 16-bit read-only registers that store the
results of A/D conversion.
An A/D conversion produces 10-bit data, which is transferred for storage into the A/D data
register corresponding to the selected channel. The upper 8 bits of the result are stored in the
upper byte of the A/D data register. The lower 2 bits are stored in the lower byte. Bits 5 to 0 of an
A/D data register are reserved bits that are always read as 0. Table 15.3 indicates the pairings of
analog input channels and A/D data registers.
The CPU can always read and write the A/D data registers. The upper byte can be read directly,
but the lower byte is read through a temporary register (TEMP). For details see section 15.3, CPU
Interface.
The A/D data registers are initialized to H'0000 by a reset and in standby mode.
Table 15.3 Analog Input Channels and A/D Data Registers
Analog Input Channel
Group 0
Group 1
A/D Data Register
AN0
AN4
ADDRA
AN1
AN5
ADDRB
AN2
AN6
ADDRC
AN3
AN7
ADDRD
Rev. 3.00 Sep 14, 2005 page 565 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.2.2
A/D Control/Status Register (ADCSR)
Bit
7
6
5
4
3
2
1
0
ADF
ADIE
ADST
SCAN
CKS
CH2
CH1
CH0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Channel select 2 to 0
These bits select analog
input channels
Clock select
Selects the A/D conversion time
Scan mode
Selects single mode or scan mode
A/D start
Starts or stops A/D conversion
A/D interrupt enable
Enables and disables A/D end interrupts
A/D end flag
Indicates end of A/D conversion
Note: * Only 0 can be written, to clear the flag.
ADCSR is an 8-bit readable/writable register that selects the mode and controls the A/D
converter. ADCSR is initialized to H'00 by a reset and in standby mode.
Rev. 3.00 Sep 14, 2005 page 566 of 910
REJ09B0258-0300
Section 15 A/D Converter
Bit 7—A/D End Flag (ADF): Indicates the end of A/D conversion.
Bit 7
ADF
Description
0
[Clearing condition]
Read ADF when ADF =1, then write 0 in ADF.
DMAC activated by ADI interrupt.
1
[Setting conditions]
Single mode: A/D conversion ends
Scan mode: A/D conversion ends in all selected channels
(Initial value)
Bit 6—A/D Interrupt Enable (ADIE): Enables or disables the interrupt (ADI) requested at the
end of A/D conversion.
Bit 6
ADIE
Description
0
A/D end interrupt request (ADI) is disabled
1
A/D end interrupt request (ADI) is enabled
(Initial value)
Bit 5—A/D Start (ADST): Starts or stops A/D conversion. The ADST bit remains set to 1 during
A/D conversion. It can also be set to 1 by external trigger input at the ADTRG pin, or by an 8-bit
timer compare match.
Bit 5
ADST
Description
0
A/D conversion is stopped
1
Single mode: A/D conversion starts; ADST is automatically cleared to 0 when
conversion ends.
Scan mode: A/D conversion starts and continues, cycling among the selected
channels, until ADST is cleared to 0 by software, by a reset, or by a transition to
standby mode.
(Initial value)
Rev. 3.00 Sep 14, 2005 page 567 of 910
REJ09B0258-0300
Section 15 A/D Converter
Bit 4—Scan Mode (SCAN): Selects single mode or scan mode. For further information on
operation in these modes, see section 15.4, Operation. Clear the ADST bit to 0 before switching
the conversion mode.
Bit 4
SCAN
Description
0
Single mode
1
Scan mode
(Initial value)
Bit 3—Clock Select (CKS): Selects the A/D conversion time. Clear the ADST bit to 0 before
switching the conversion time.
Bit 3
CKS
Description
0
Conversion time = 134 states (maximum)
1
Conversion time = 70 states (maximum)
(Initial value)
Bits 2 to 0—Channel Select 2 to 0 (CH2 to CH0): These bits and the SCAN bit select the
analog input channels. Clear the ADST bit to 0 before changing the channel selection.
Group
Selection
Channel Selection
Description
CH2
CH1
CH0
Single Mode
Scan Mode
0
0
0
AN0 (Initial value)
AN0
1
AN1
AN0, AN1
0
AN2
AN0 to AN2
1
AN3
AN0 to AN3
0
AN4
AN4
1
AN5
AN4, AN5
0
AN6
AN4 to AN6
1
AN7
AN4 to AN7
1
1
0
1
Rev. 3.00 Sep 14, 2005 page 568 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.2.3
A/D Control Register (ADCR)
Bit
7
6
5
4
3
2
1
0
TRGE
—
—
—
—
—
—
—
Initial value
0
1
1
1
1
1
1
0
Read/Write
R/W
—
—
—
—
—
—
R/W
Reserved bits
Trigger enable
Enables or disables starting of A/D conversion
by an external trigger or 8-bit timer compare match
ADCR is an 8-bit readable/writable register that enables or disables starting of A/D conversion by
external trigger input or an 8-bit timer compare match signal. ADCR is initialized to H'7F by a
reset and in standby mode.
Bit 7—Trigger Enable (TRGE): Enables or disables starting of A/D conversion by an external
trigger or 8-bit timer compare match.
Bit 7
TRGE
Description
0
Starting of A/D conversion by an external trigger or 8-bit timer
compare match is disabled
1
A/D conversion is started at the falling edge of the external trigger
signal (ADTRG) or by an 8-bit timer compare match
(Initial value)
External trigger pin and 8-bit timer selection are performed by the 8-bit timer. For details, see
section 10, 8-Bit Timers.
Bits 6 to 1—Reserved: These bits cannot be modified and are always read as 1.
Bit 0—Reserved: This bit can be read or written, but must not be set to 1.
Rev. 3.00 Sep 14, 2005 page 569 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.3
CPU Interface
ADDRA to ADDRD are 16-bit registers, but they are connected to the CPU by an 8-bit data bus.
Therefore, although the upper byte can be be accessed directly by the CPU, the lower byte is read
through an 8-bit temporary register (TEMP).
An A/D data register is read as follows. When the upper byte is read, the upper-byte value is
transferred directly to the CPU and the lower-byte value is transferred into TEMP. Next, when
the lower byte is read, the TEMP contents are transferred to the CPU.
When reading an A/D data register, always read the upper byte before the lower byte. It is
possible to read only the upper byte, but if only the lower byte is read, incorrect data may be
obtained.
Figure 15.2 shows the data flow for access to an A/D data register.
Rev. 3.00 Sep 14, 2005 page 570 of 910
REJ09B0258-0300
Section 15 A/D Converter
Upper-byte read
CPU
(H'AA)
Module data bus
Bus interface
TEMP
(H'40)
ADDRnH
(H'AA)
ADDRnL
(H'40)
(n = A to D)
Lower-byte read
CPU
(H'40)
Module data bus
Bus interface
TEMP
(H'40)
ADDRnH
(H'AA)
ADDRnL
(H'40)
(n = A to D)
Figure 15.2 A/D Data Register Access Operation (Reading H'AA40)
Rev. 3.00 Sep 14, 2005 page 571 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.4
Operation
The A/D converter operates by successive approximations with 10-bit resolution. It has two
operating modes: single mode and scan mode.
15.4.1
Single Mode (SCAN = 0)
Single mode should be selected when only one A/D conversion on one channel is required. A/D
conversion starts when the ADST bit is set to 1 by software, or by external trigger input. The
ADST bit remains set to 1 during A/D conversion and is automatically cleared to 0 when
conversion ends.
When conversion ends the ADF bit is set to 1. If the ADIE bit is also set to 1, an ADI interrupt is
requested at this time. To clear the ADF flag to 0, first read ADCSR, then write 0 in ADF.
When the mode or analog input channel must be switched during analog conversion, to prevent
incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making
the necessary changes, set the ADST bit to 1 to start A/D conversion again. The ADST bit can be
set at the same time as the mode or channel is changed.
Typical operations when channel 1 (AN1) is selected in single mode are described next.
Figure 15.3 shows a timing diagram for this example.
1. Single mode is selected (SCAN = 0), input channel AN1 is selected (CH2 = CH1 = 0,
CH0 = 1), the A/D interrupt is enabled (ADIE = 1), and A/D conversion is started
(ADST = 1).
2. When A/D conversion is completed, the result is transferred into ADDRB. At the same time
the ADF flag is set to 1, the ADST bit is cleared to 0, and the A/D converter becomes idle.
3. Since ADF = 1 and ADIE = 1, an ADI interrupt is requested.
4. The A/D interrupt handling routine starts.
5. The routine reads ADCSR, then writes 0 in the ADF flag.
6. The routine reads and processes the conversion result (ADDRB).
7. Execution of the A/D interrupt handling routine ends. After that, if the ADST bit is set to 1,
A/D conversion starts again and steps 2 to 7 are repeated.
Rev. 3.00 Sep 14, 2005 page 572 of 910
REJ09B0258-0300
Note: * Vertical arrows ( ) indicate instructions executed by software.
ADDRD
ADDRC
ADDRB
Read conversion result
A/D conversion result (2)
Idle
Clear*
A/D conversion result (1)
A/D conversion (2)
Set*
Read conversion result
Idle
State of channel 3
(AN 3)
ADDRA
Idle
State of channel 2
(AN 2)
Idle
Clear*
State of channel 1
(AN 1)
A/D conversion (1)
Set*
Idle
Idle
A/D conversion
starts
State of channel 0
(AN 0)
ADF
ADST
ADIE
Set*
Section 15 A/D Converter
Figure 15.3 Example of A/D Converter Operation (Single Mode, Channel 1 Selected)
Rev. 3.00 Sep 14, 2005 page 573 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.4.2
Scan Mode (SCAN = 1)
Scan mode is useful for monitoring analog inputs in a group of one or more channels. When the
ADST bit is set to 1 by software or external trigger input, A/D conversion starts on the first
channel in the group (AN0 when CH2 = 0, AN4 when CH2 = 1). When two or more channels are
selected, after conversion of the first channel ends, conversion of the second channel (AN1 or
AN5) starts immediately. A/D conversion continues cyclically on the selected channels until the
ADST bit is cleared to 0. The conversion results are transferred for storage into the A/D data
registers corresponding to the channels.
When the mode or analog input channel selection must be changed during analog conversion, to
prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After
making the necessary changes, set the ADST bit to 1. A/D conversion will start again from the
first channel in the group. The ADST bit can be set at the same time as the mode or channel
selection is changed.
Typical operations when three channels in group 0 (AN0 to AN2) are selected in scan mode are
described next. Figure 15.4 shows a timing diagram for this example.
1. Scan mode is selected (SCAN = 1), scan group 0 is selected (CH2 = 0), analog input channels
AN0 to AN2 are selected (CH1 = 1, CH0 = 0), and A/D conversion is started (ADST = 1).
2. When A/D conversion of the first channel (AN0) is completed, the result is transferred into
ADDRA. Next, conversion of the second channel (AN1) starts automatically.
3. Conversion proceeds in the same way through the third channel (AN2).
4. When conversion of all selected channels (AN0 to AN2) is completed, the ADF flag is set to 1
and conversion of the first channel (AN0) starts again. If the ADIE bit is set to 1, an ADI
interrupt is requested at this time.
5. Steps 2 to 4 are repeated as long as the ADST bit remains set to 1. When the ADST bit is
cleared to 0, A/D conversion stops. After that, if the ADST bit is set to 1, A/D conversion
starts again from the first channel (AN0).
Rev. 3.00 Sep 14, 2005 page 574 of 910
REJ09B0258-0300
Idle
Idle
Idle
A/D conversion (1)
Transfer
Idle
A/D conversion (3)
Idle
Idle
Clear*1
Idle
A/D conversion result (4)
Idle
A/D conversion (5)*2
A/D conversion result (3)
A/D conversion result (2)
A/D conversion (4)
A/D conversion result (1)
A/D conversion (2)
Idle
A/D conversion time
Continuous A/D conversion
Notes: 1. Vertical arrows ( ) indicate instructions executed by software.
2. Data currently being converted is ignored.
ADDRD
ADDRC
ADDRB
ADDRA
State of channel 3
(AN 3)
State of channel 2
(AN 2)
State of channel 1
(AN 1)
State of channel 0
(AN 0)
ADF
ADST
Set*1
Clear*1
Section 15 A/D Converter
Figure 15.4 Example of A/D Converter Operation (Scan Mode,
Channels AN0 to AN2 Selected)
Rev. 3.00 Sep 14, 2005 page 575 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.4.3
Input Sampling and A/D Conversion Time
The A/D converter has a built-in sample-and-hold circuit. The A/D converter samples the analog
input at a time tD after the ADST bit is set to 1, then starts conversion. Figure 15.5 shows the A/D
conversion timing. Table 15.4 indicates the A/D conversion time.
As indicated in figure 15.5, the A/D conversion time includes tD and the input sampling time. The
length of tD varies depending on the timing of the write access to ADCSR. The total conversion
time therefore varies within the ranges indicated in table 15.4.
In scan mode, the values given in table 15.4 apply to the first conversion. In the second and
subsequent conversions the conversion time is fixed at 128 states when CKS = 0 or 66 states
when CKS = 1.
Rev. 3.00 Sep 14, 2005 page 576 of 910
REJ09B0258-0300
Section 15 A/D Converter
(1)
φ
Address bus
(2)
Write signal
Input sampling
timing
ADF
tD
t SPL
t CONV
Legend
(1):
ADCSR write cycle
(2):
ADCSR address
tD :
Synchronization delay
t SPL : Input sampling time
t CONV: A/D conversion time
Figure 15.5 A/D Conversion Timing
Table 15.4 A/D Conversion Time (Single Mode)
CKS = 0
CKS = 1
Symbol
Min
Typ
Max
Min
Typ
Max
Synchronization delay
tD
6
—
9
4
—
5
Input sampling time
tSPL
—
31
—
—
15
—
A/D conversion time
tCONV
131
—
134
69
—
70
Note: Values in the table are numbers of states.
Rev. 3.00 Sep 14, 2005 page 577 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.4.4
External Trigger Input Timing
A/D conversion can be externally triggered. When the TRGE bit is set to 1 in ADCR and the 8-bit
timer's ADTE bit is cleared to 0, external trigger input is enabled at the ADTRG pin. A high-tolow transition at the ADTRG pin sets the ADST bit to 1 in ADCSR, starting A/D conversion.
Other operations, in both single and scan modes, are the same as if the ADST bit had been set to 1
by software. Figure 15.6 shows the timing.
φ
ADTRG
Internal trigger
signal
ADST
A/D conversion
Figure 15.6 External Trigger Input Timing
Rev. 3.00 Sep 14, 2005 page 578 of 910
REJ09B0258-0300
Section 15 A/D Converter
15.5
Interrupts
The A/D converter generates an interrupt (ADI) at the end of A/D conversion. The ADI interrupt
request can be enabled or disabled by the ADIE bit in ADCSR. The ADI interrupt request can be
designated as a DMAC activation source. In this case, an interrupt request is not sent to the CPU.
15.6
Usage Notes
When using the A/D converter, note the following points:
1. Analog Input Voltage Range: During A/D conversion, the voltages input to the analog input
pins should be in the range AVSS ≤ ANn ≤ VREF.
2. Relationships of AVCC and AVSS to VCC and VSS: AVCC, AVSS, VCC, and VSS should be related
as follows: AVSS = VSS. AVCC and AVSS must not be left open, even if the A/D converter is
not used.
3. VREF Programming Range: The reference voltage input at the VREF pin should be in the range
VREF ≤ AVCC.
4. Note on Board Design: In board layout, separate the digital circuits from the analog circuits as
much as possible. Particularly avoid layouts in which the signal lines of digital circuits cross
or closely approach the signal lines of analog circuits. Induction and other effects may cause
the analog circuits to operate incorrectly, or may adversely affect the accuracy of A/D
conversion.
The analog input signals (AN0 to AN7), analog reference voltage (VREF), and analog supply
voltage (AVCC) must be separated from digital circuits by the analog ground (AVSS). The
analog ground (AVSS) should be connected to a stable digital ground (VSS) at one point on the
board.
5. Note on Noise: To prevent damage from surges and other abnormal voltages at the analog
input pins (AN0 to AN7) and analog reference voltage pin (VREF), connect a protection circuit
like the one in figure 15.7 between AVCC and AVSS. The bypass capacitors connected to AVCC
and VREF and the filter capacitors connected to AN0 to AN7 must be connected to AVSS. If
filter capacitors like the ones in figure 15.7 are connected, the voltage values input to the
analog input pins (AN0 to AN7) will be smoothed, which may give rise to error. Error can also
occur if A/D conversion is frequently performed in scan mode so that the current that charges
and discharges the capacitor in the sample-and-hold circuit of the A/D converter becomes
greater than that input to the analog input pins via input impedance Rin. The circuit constants
should therefore be selected carefully.
Rev. 3.00 Sep 14, 2005 page 579 of 910
REJ09B0258-0300
Section 15 A/D Converter
AVCC
VREF
100 Ω
Rin*2
*1
AN0 to AN7
*1
0.1 µF
AVSS
Notes: 1.
10 µF
2.
0.01 µF
Rin: input impedance
Figure 15.7 Example of Analog Input Protection Circuit
Table 15.5 Analog Input Pin Ratings
Item
min
max
Unit
Analog input capacitance
—
20
pF
Allowable signal-source impedance
—
10*
kΩ
Note: * When conversion time = 134 states, VCC = 4.0 V to 5.5 V, and ø ≤ 13 Mhz. For details see
section 21, Electrical Characteristics.
10 kΩ
AN0 to AN7
To A/D converter
20 pF
Figure 15.8 Analog Input Pin Equivalent Circuit
Note: Numeric values are approximate, except in table 15.5
Rev. 3.00 Sep 14, 2005 page 580 of 910
REJ09B0258-0300
Section 15 A/D Converter
6. A/D Conversion Accuracy Definitions: A/D conversion accuracy in the H8/3068F is defined
as follows:
• Resolution:
Digital output code length of A/D converter
• Offset error:
Deviation from ideal A/D conversion characteristic of analog input
voltage required to raise digital output from minimum voltage value
0000000000 to 0000000001 (figure 15.10)
• Full-scale error:
Deviation from ideal A/D conversion characteristic of analog input
voltage required to raise digital output from 1111111110 to 1111111111
(figure 15.10)
• Quantization error: Intrinsic error of the A/D converter; 1/2 LSB (figure 15.9)
• Nonlinearity error: Deviation from ideal A/D conversion characteristic in range from zero
volts to full scale, exclusive of offset error, full-scale error, and
quantization error.
• Absolute accuracy: Deviation of digital value from analog input value, including offset error,
full-scale error, quantization error, and nonlinearity error.
Digital
output
111
Ideal A/D conversion
characteristic
110
101
100
011
010
Quantization error
001
000
1/8 2/8 3/8 4/8 5/8 6/8 7/8 FS
Analog input
voltage
Figure 15.9 A/D Converter Accuracy Definitions (1)
Rev. 3.00 Sep 14, 2005 page 581 of 910
REJ09B0258-0300
Section 15 A/D Converter
Full-scale
error
Digital
output
Ideal A/D
conversion
characteristic
Nonlinearity
error
Actual A/D conversion
characteristic
FS
Offset error
Analog input
voltage
Figure 15.10 A/D Converter Accuracy Definitions (2)
7. Allowable Signal-Source Impedance: The analog inputs of the H8/3068F are designed to
assure accurate conversion of input signals with a signal-source impedance not exceeding 10
kΩ. The reason for this rating is that it enables the input capacitor in the sample-and-hold
circuit in the A/D converter to charge within the sampling time. If the sensor output
impedance exceeds 10 kΩ, charging may be inadequate and the accuracy of A/D conversion
cannot be guaranteed.
If a large external capacitor is provided in single mode, then the internal 10-kΩ input
resistance becomes the only significant load on the input. In this case the impedance of the
signal source is not a problem.
A large external capacitor, however, acts as a low-pass filter. This may make it impossible to
track analog signals with high dv/dt (e.g. a variation of 5 mV/µs) (figure 15.11). To convert
high-speed analog signals or to use scan mode, insert a low-impedance buffer.
8. Effect on Absolute Accuracy: Attaching an external capacitor creates a coupling with ground,
so if there is noise on the ground line, it may degrade absolute accuracy. The capacitor must
be connected to an electrically stable ground, such as AVSS.
Rev. 3.00 Sep 14, 2005 page 582 of 910
REJ09B0258-0300
Section 15 A/D Converter
If a filter circuit is used, be careful of interference with digital signals on the same board, and
make sure the circuit does not act as an antenna.
H8/3067 Group
Sensor output impedance
Sensor
input
10 kΩ
Up to 10 kΩ
Low-pass
filter
C Up to 0.1µF
Equivalent circuit of
A/D converter
Cin =
15 pF
20 pF
Figure 15.11 Analog Input Circuit (Example)
Rev. 3.00 Sep 14, 2005 page 583 of 910
REJ09B0258-0300
Section 15 A/D Converter
Rev. 3.00 Sep 14, 2005 page 584 of 910
REJ09B0258-0300
Section 16 D/A Converter
Section 16 D/A Converter
16.1
Overview
The H8/3068F includes a D/A converter with two channels.
16.1.1
Features
D/A converter features are listed below.
•
•
•
•
•
Eight-bit resolution
Two output channels
Conversion time: maximum 10 µs (with 20-pF capacitive load)
Output voltage: 0 V to VREF
D/A outputs can be sustained in software standby mode
Rev. 3.00 Sep 14, 2005 page 585 of 910
REJ09B0258-0300
Section 16 D/A Converter
16.1.2
Block Diagram
Bus interface
Figure 16.1 shows a block diagram of the D/A converter.
Module data bus
Internal
data bus
DACR
8-bit D/A
DADR1
DA 0
DADR0
AVCC
DASTCR
VREF
DA 1
AVSS
Legend
DACR: D/A control register
DADR0: D/A data register 0
DADR1: D/A data register 1
DASTCR: D/A standby control register
Control circuit
Figure 16.1 D/A Converter Block Diagram
16.1.3
Input/Output Pins
Table 16.1 summarizes the D/A converter's input and output pins.
Table 16.1 D/A Converter Pins
Pin Name
Abbreviation I/O
Function
Analog power supply pin
AVCC
Input
Analog power supply and reference voltage
Analog ground pin
AVSS
Input
Analog ground and reference voltage
Analog output pin 0
DA0
Output
Analog output, channel 0
Analog output pin 1
DA1
Output
Analog output, channel 1
Input
Analog reference voltage
Reference voltage input pin VREF
Rev. 3.00 Sep 14, 2005 page 586 of 910
REJ09B0258-0300
Section 16 D/A Converter
16.1.4
Register Configuration
Table 16.2 summarizes the D/A converter's registers.
Table 16.2 D/A Converter Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFF9C
D/A data register 0
DADR0
R/W
H'00
H'FFF9D
D/A data register 1
DADR1
R/W
H'00
H'FFF9E
D/A control register
DACR
R/W
H'1F
H'EE01A
D/A standby control register
DASTCR
R/W
H'FE
Note: * Lower 20 bits of the address in advanced mode.
Rev. 3.00 Sep 14, 2005 page 587 of 910
REJ09B0258-0300
Section 16 D/A Converter
16.2
Register Descriptions
16.2.1
D/A Data Registers 0 and 1 (DADR0/1)
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The D/A data registers (DADR0 and DADR1) are 8-bit readable/writable registers that store the
data to be converted. When analog output is enabled, the D/A data register values are constantly
converted and output at the analog output pins.
The D/A data registers are initialized to H'00 by a reset and in standby mode.
When the DASTE bit is set to 1 in the D/A standby control register (DASTCR), the D/A registers
are not initialized in software standby mode.
16.2.2
D/A Control Register (DACR)
Bit
7
6
5
4
3
2
1
0
DAOE1
DAOE0
DAE
—
—
—
—
—
Initial value
0
0
0
1
1
1
1
1
Read/Write
R/W
R/W
R/W
—
—
—
—
—
D/A enable
Controls D/A conversion
D/A output enable 0
Controls D/A conversion and analog output
D/A output enable 1
Controls D/A conversion and analog output
DACR is an 8-bit readable/writable register that controls the operation of the D/A converter.
DACR is initialized to H'1F by a reset and in standby mode.
When the DASTE bit is set to 1 in DASTCR, the DACR is not initialized in software standby
mode.
Rev. 3.00 Sep 14, 2005 page 588 of 910
REJ09B0258-0300
Section 16 D/A Converter
Bit 7—D/A Output Enable 1 (DAOE1): Controls D/A conversion and analog output.
Bit 7
DAOE1
Description
0
DA1 analog output is disabled
1
Channel-1 D/A conversion and DA1 analog output are enabled
Bit 6—D/A Output Enable 0 (DAOE0): Controls D/A conversion and analog output.
Bit 6
DAOE0
Description
0
DA0 analog output is disabled
1
Channel-0 D/A conversion and DA0 analog output are enabled
Bit 5—D/A Enable (DAE): Controls D/A conversion, together with bits DAOE0 and DAOE1.
When the DAE bit is cleared to 0, analog conversion is controlled independently in channels 0
and 1. When the DAE bit is set to 1, analog conversion is controlled together in channels 0 and 1.
Output of the conversion results is always controlled independently by DAOE0 and DAOE1.
Bit 7
DAOE1
Bit 6
Bit 5
DAOE0 DAE
Description
0
0
—
D/A conversion is disabled in channels 0 and 1
1
0
D/A conversion is enabled in channel 0
D/A conversion is disabled in channel 1
1
1
0
0
D/A conversion is enabled in channels 0 and 1
D/A conversion is disabled in channel 0
D/A conversion is enabled in channel 1
1
1
D/A conversion is enabled in channels 0 and 1
—
D/A conversion is enabled in channels 0 and 1
When the DAE bit is set to 1, even if bits DAOE0 and DAOE1 in DACR and the ADST bit in
ADCSR are cleared to 0, the same current is drawn from the analog power supply as during A/D
and D/A conversion.
Bits 4 to 0—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 589 of 910
REJ09B0258-0300
Section 16 D/A Converter
16.2.3
D/A Standby Control Register (DASTCR)
DASTCR is an 8-bit readable/writable register that enables or disables D/A output in software
standby mode.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
DASTE
Initial value
1
1
1
1
1
1
1
0
Read/Write
—
—
—
—
—
—
—
R/W
Reserved bits
D/A standby enable
Enables or disables D/A output
in software standby mode
DASTCR is initialized to H'FE by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 1—Reserved: These bits cannot be modified and are always read as 1.
Bit 0—D/A Standby Enable (DASTE): Enables or disables D/A output in software standby
mode.
Bit 0
DASTE
Description
0
D/A output is disabled in software standby mode
1
D/A output is enabled in software standby mode
Rev. 3.00 Sep 14, 2005 page 590 of 910
REJ09B0258-0300
(Initial value)
Section 16 D/A Converter
16.3
Operation
The D/A converter has two built-in D/A conversion circuits that can perform conversion
independently.
D/A conversion is performed constantly while enabled in DACR. If the DADR0 or DADR1 value
is modified, conversion of the new data begins immediately. The conversion results are output
when bits DAOE0 and DAOE1 are set to 1.
An example of D/A conversion on channel 0 is given next. Timing is indicated in figure 16.2.
1. Data to be converted is written in DADR0.
2. Bit DAOE0 is set to 1 in DACR. D/A conversion starts and DA0 becomes an output pin. The
converted result is output after the conversion time.
The output value is
DADR contents
× VREF
256
Output of this conversion result continues until the value in DADR0 is modified or the
DAOE0 bit is cleared to 0.
3. If the DADR0 value is modified, conversion starts immediately, and the result is output after
the conversion time.
4. When the DAOE0 bit is cleared to 0, DA0 becomes an input pin.
Rev. 3.00 Sep 14, 2005 page 591 of 910
REJ09B0258-0300
Section 16 D/A Converter
DADR0
write cycle
DACR
write cycle
DADR0
write cycle
DACR
write cycle
φ
Address
Conversion data 1
DADR0
Conversion data 2
DAOE0
DA 0
Conversion
result 2
Conversion
result 1
High-impedance state
t DCONV
t DCONV
Legend
t DCONV : D/A conversion time
Figure 16.2 Example of D/A Converter Operation
16.4
D/A Output Control
In the H8/3068F, D/A converter output can be enabled or disabled in software standby mode.
When the DASTE bit is set to 1 in DASTCR, D/A converter output is enabled in software standby
mode. The D/A converter registers retain the values they held prior to the transition to software
standby mode.
When D/A output is enabled in software standby mode, the reference supply current is the same
as during normal operation.
Rev. 3.00 Sep 14, 2005 page 592 of 910
REJ09B0258-0300
Section 17 RAM
Section 17 RAM
17.1
Overview
The H8/3068F has 16 kbytes RAM. The RAM is connected to the CPU by a 16-bit data bus. The
CPU accesses both byte data and word data in two states, making the RAM useful for rapid data
transfer.
The on-chip RAM of the H8/3068F is assigned to addresses H'FBF20 to H'FFF1F in modes 1, 2,
and 7, and to addresses H'FFBF20 to H'FFFF1F in modes 3, 4, and 5,and to addresses H'E720 to
H'FF1F in mode 6. The RAM enable bit (RAME) in the system control register (SYSCR) can
enable or disable the on-chip RAM.
Rev. 3.00 Sep 14, 2005 page 593 of 910
REJ09B0258-0300
Section 17 RAM
17.1.1
Block Diagram
Figure 17.1 shows a block diagram of the on-chip RAM.
On-chip data bus (upper 8 bits)
On-chip data bus (lower 8 bits)
Bus interface
H'FBF20*
H'FBF21*
H'FBF22*
H'FBF23*
SYSCR
On-chip RAM
H'FFF1E*
H'FFF1F*
Even addresses
Odd addresses
Legend
SYSCR: System control register
Note: * Lower 20 bits of the address in mode 7.
Figure 17.1 RAM Block Diagram
17.1.2
Register Configuration
The on-chip RAM is controlled by SYSCR. Table 17.1 gives the address and initial value of
SYSCR.
Table 17.1 System Control Register
Address*
Name
Abbreviation
R/W
Initial Value
H'EE012
System control register
SYSCR
R/W
H'09
Note: * Lower 20 bits of the address in advanced mode.
Rev. 3.00 Sep 14, 2005 page 594 of 910
REJ09B0258-0300
Section 17 RAM
17.2
System Control Register (SYSCR)
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
Initial value
0
0
0
0
1
0
0
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RAM enable bit
Enables or disables
on-chip RAM
Software standby
output port enable
NMI edge select
User bit enable
Standby timer select 2 to 0
Software standby
One function of SYSCR is to enable or disable access to the on-chip RAM. The on-chip RAM is
enabled or disabled by the RAME bit in SYSCR. For details about the other bits, see section 3.3,
System Control Register (SYSCR).
Bit 0—RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is
initialized at the rising edge of the input at the RES pin. It is not initialized in software standby
mode.
Bit 0
RAME
Description
0
On-chip RAM is disabled
1
On-chip RAM is enabled
(Initial value)
Rev. 3.00 Sep 14, 2005 page 595 of 910
REJ09B0258-0300
Section 17 RAM
17.3
Operation
When the RAME bit is set to 1, the on-chip RAM is enabled. Accesses to addresses H'FBF20 to
H'FFF1F in modes 1, 2, and 7, and to addresses H'FFBF20 to H'FFFF1F in the H8/3068F in
modes 3, 4, and 5, and to addresses H'7F20 to H'FF1F in mode 6, are directed to the on-chip
RAM. In modes 1 to 5 (expanded modes), when the RAME bit is cleared to 0, the off-chip
address space is accessed. In mode 6, 7 (single-chip mode), when the RAME bit is cleared to 0,
the on-chip RAM is not accessed: read access always results in H'FF data, and write access is
ignored.
Since the on-chip RAM is connected to the CPU by an internal 16-bit data bus, it can be written
and read by word access. It can also be written and read by byte access. Byte data is accessed in
two states using the upper 8 bits of the data bus. Word data starting at an even address is accessed
in two states using all 16 bits of the data bus.
Rev. 3.00 Sep 14, 2005 page 596 of 910
REJ09B0258-0300
Section 18 Flash Memory
Section 18 Flash Memory
18.1
Overview
The H8/3068F-ZTAT has 384 kbytes of on-chip flash memory. The flash memory is connected to
the CPU by a 16-bit data bus. The CPU accesses both byte data and word data in two states,
enabling rapid data transfer.
The on-chip ROM is enabled and disabled by setting the mode pins (MD2 to MD0) as shown in
table 18.1.
The on-chip flash memory product (H8/3068F-ZTAT) can be erased and programmed on-board,
as well as with a special-purpose PROM programmer.
Table 18.1 Operating Modes and ROM
Mode Pins
Mode
MD2
MD1
MD0
On-Chip ROM
Mode 1 (expanded 1-Mbyte mode with on-chip ROM
disabled)
0
0
1
Disabled (external
address area)
Mode 2 (expanded 1-Mbyte mode with on-chip ROM
disabled)
0
1
0
Mode 3 (expanded 16-Mbyte mode with on-chip ROM
disabled)
0
1
1
Mode 4 (expanded 16-Mbyte mode with on-chip ROM
disabled)
1
0
0
Mode 5 (expanded 16-Mbyte mode with on-chip ROM
enabled)
1
0
1
Mode 6 (single-chip normal mode)
1
1
0
Mode 7 (single-chip advanced mode)
1
1
1
Enabled
Rev. 3.00 Sep 14, 2005 page 597 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.2
Features
The H8/3068F-ZTAT has 384 kbytes of on-chip flash memory.
The features of the flash memory are summarized below.
• Four flash memory operating modes
 Program mode
 Erase mode
 Program-verify mode
 Erase-verify mode
• Programming/erase methods
The flash memory is programmed 128 bytes at a time. Erasing is performed in block units. To
erase the entire flash memory, each block must be erased in turn. In block erasing, 4-kbyte,
32-kbyte, and 64-kbyte blocks can be set arbitrarily.
• Programming/erase times
The flash memory programming time is 10 ms (typ.) for simultaneous 128-byte programming,
equivalent approximately to 80 µs (typ.) per byte, and the erase time is 100 ms (typ.) per
block.
• Reprogramming capability
The flash memory can be reprogrammed up to 100 times.
• On-board programming modes
There are two modes in which flash memory can be programmed/erased/verified on-board:
 Boot mode
 User program mode
• Automatic bit rate adjustment
For data transfer in boot mode, the H8/3068F-ZTAT chip’s bit rate can be automatically
adjusted to match the transfer bit rate of the host.
• Flash memory emulation in RAM
Flash memory programming can be emulated in real time by overlapping a part of RAM onto
flash memory.
• Protect modes
There are three protect modes—hardware, software, and error—which allow protected status
to be designated for flash memory program/erase/verify operations
• PROM mode
Flash memory can be programmed/erased in PROM mode, using a PROM programmer, as
well as in on-board programming mode.
Rev. 3.00 Sep 14, 2005 page 598 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.2.1
Block Diagram
Internal address bus
Module bus
Internal data bus (16 bits)
FLMCR1
FLMCR2
EBR1
Bus interface/controller
Operating
mode
FWE pin
Mode pins
EBR2
RAMCR
Flash memory
(384 kbytes)
Legend
FLMCR1:
FLMCR2:
EBR1:
EBR2:
RAMCR:
Flash memory control register 1
Flash memory control register 2
Erase block register 1
Erase block register 2
RAM control register
Figure 18.1 Block Diagram of Flash Memory
Rev. 3.00 Sep 14, 2005 page 599 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.2.2
Pin Configuration
The flash memory is controlled by means of the pins shown in table 18.2.
Table 18.2 Flash Memory Pins
Pin Name
Abbreviation
I/O
Function
Reset
RES
Input
Reset
Flash write enable
FWE
Input
Flash program/erase protection by hardware
Mode 2
MD2
Input
Sets H8/3068F-ZTAT operating mode
Mode 1
MD1
Input
Sets H8/3068F-ZTAT operating mode
Mode 0
MD0
Input
Sets H8/3068F-ZTAT operating mode
Transmit data
TxD1
Output
Serial transmit data output
Receive data
RxD1
Input
Serial receive data input
18.2.3
Register Configuration
The registers used to control the on-chip flash memory when enabled are shown in table 18.3.
Table 18.3 Flash Memory Registers
Register Name
Abbreviation
R/W
Initial Value
2
Address*1
Flash memory control register 1
FLMCR1
R/W
H'00*
H'EE030
Flash memory control register 2
FLMCR2
R
H'00
H'EE031
Erase block register 1
EBR1
R/W
H'00
H'EE032
Erase block register 2
EBR2
R/W
H'00
H'EE033
RAM control register
RAMCR
R/W
H'F0
H'EE077
Notes: FLMCR1, FLMCR2, EBR1, EBR2, and RAMCR are 8-bit registers, and should be
accessed by byte access.
1. Lower 20 bits of address in advanced mode.
2. When a high level is input to the FWE pin, the initial value is H'80.
Rev. 3.00 Sep 14, 2005 page 600 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.3
Register Descriptions
18.3.1
Flash Memory Control Register 1 (FLMCR1)
Bit
7
6
5
4
3
2
1
0
FWE
SWE
ESU
PSU
EV
PV
E
P
Initial value
—*
0
0
0
0
0
0
0
Read/Write
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Note: * Determined by the state of the FWE pin.
FLMCR1 is an 8-bit register used for flash memory operating mode control.
Program-verify mode or erase-verify mode for addresses H'00000 to H'5FFFF is entered by
setting the SWE bit when FWE = 1, then setting the PV or EV bit. Program mode for addresses
H'00000 to H'5FFFF is entered by setting the SWE bit when FWE = 1, then setting the PSU bit,
and finally setting the P bit. Erase mode for addresses H'00000 to H'5FFFF is entered by setting
the SWE bit when FWE = 1, then setting the ESU bit, and finally setting the E bit. FLMCR1 is
initialized by a reset, and in hardware standby mode and software standby mode. Its initial value
is H'80 when a high level is input to the FWE pin, and H'00 when a low level is input. In mode 6
the FWE pin must be fixed low since flash memory on-board programming modes are not
supported. When the on-chip flash memory is disabled, a read access to this register will return
H'00, and writes are invalid.
When setting bits 6 to 0 in this register, one bit must be set one at a time. Writes to the SWE bit in
FLMCR1 are enabled only when FWE = 1; writes to bits ESU, PSU, EV, and PV only when FWE
= 1 and SWE = 1; writes to the E bit only when FWE = 1, SWE = 1, and ESU = 1; and writes to
the P bit only when FWE = 1, SWE = 1, and PSU = 1.
Notes: 1. The programming and erase flowcharts must be followed when setting the bits in this
register to prevent erroneous programming or erasing.
2. Transitions are made to program mode, erase mode, program-verify mode, and eraseverify mode according to the settings in this register. When reading flash memory as
normal on-chip ROM, bits 6 to 0 in this register must be cleared.
Rev. 3.00 Sep 14, 2005 page 601 of 910
REJ09B0258-0300
Section 18 Flash Memory
Bit 7—Flash Write Enable (FWE): Sets hardware protection against flash memory
programming/erasing.
Bit 7
FWE
Description
0
When a low level is input to the FWE pin (hardware-protected state)
1
When a high level is input to the FWE pin
Bit 6—Software Write Enable (SWE): Enables or disables flash memory programming and
erasing. (This bit should be set when setting bits 5 to 0, EBR1 bits 7 to 0, and EBR2 bits 3 to 0.)
Bit 6
SWE
Description
0
Programming/erasing disabled
1
Programming/erasing enabled
(Initial value)
[Setting condition]
When FWE = 1
Note: Do not execute a SLEEP instruction while the SWE bit is set to 1.
Bit 5—Erase Setup (ESU): Prepares for a transition to erase mode. Set this bit to 1 before
setting the E bit to 1 in FLMCR1 (do not set the SWE, PSU, EV, PV, E, or P bit at the same
time).
Bit 5
ESU
Description
0
Erase setup cleared
1
Erase setup
[Setting condition]
When FWE = 1 and SWE = 1
Rev. 3.00 Sep 14, 2005 page 602 of 910
REJ09B0258-0300
(Initial value)
Section 18 Flash Memory
Bit 4—Program Setup (PSU): Prepares for a transition to program mode. Set this bit to 1 before
setting the P bit to 1 in FLMCR1 (do not set the SWE, ESU, EV, PV, E, or P bit at the same
time).
Bit 4
PSU
Description
0
Program setup cleared
1
Program setup
(Initial value)
[Setting condition]
When FWE = 1 and SWE = 1
Bit 3—Erase-Verify Mode (EV): Selects erase-verify mode transition or clearing. (Do not set
the SWE, ESU, PSU, PV, E, or P bit at the same time.)
Bit 3
EV
Description
0
Erase-verify mode cleared
1
Transition to erase-verify mode
(Initial value)
[Setting condition]
When FWE = 1 and SWE = 1
Bit 2—Program-Verify Mode (PV): Selects program-verify mode transition or clearing. (Do
not set the SWE, ESU, PSU, EV, E, or P bit at the same time.)
Bit 2
PV
Description
0
Program-verify mode cleared
1
Transition to program-verify mode
(Initial value)
[Setting condition]
When FWE = 1 and SWE = 1
Rev. 3.00 Sep 14, 2005 page 603 of 910
REJ09B0258-0300
Section 18 Flash Memory
Bit 1—Erase Mode (E): Selects erase mode transition or clearing. (Do not set the SWE, ESU,
PSU, EV, PV, or P bit at the same time.)
Bit 1
E
Description
0
Erase mode cleared
1
Transition to erase mode
(Initial value)
[Setting condition]
When FWE = 1, SWE = 1, and ESU = 1
Note: Do not access the flash memory while the E bit is set.
Bit 0—Program (P): Selects program mode transition or clearing. (Do not set the SWE, ESU,
PSU, EV, PV, or E bit at the same time.)
Bit 0
P
Description
0
Program mode cleared
1
Transition to program mode
(Initial value)
[Setting condition]
When FWE = 1, SWE = 1, and PSU = 1
Note: Do not access the flash memory while the P bit is set.
18.3.2
Flash Memory Control Register 2 (FLMCR2)
Bit
7
6
5
4
3
2
1
0
FLER
—
—
—
—
—
—
—
Initial value
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
FLMCR2 is an 8-bit register used for flash memory operating mode control. FLMCR2 is
initialized to H'00 by a reset, and in hardware standby mode and software standby mode. When
the on-chip flash memory is disabled, a read will return H'00.
Note: FLMCR2 is a read-only register, and should not be written to.
Rev. 3.00 Sep 14, 2005 page 604 of 910
REJ09B0258-0300
Section 18 Flash Memory
Bit 7—Flash Memory Error (FLER): Indicates that an error has occurred during an operation
on flash memory (programming or erasing). When FLER is set to 1, flash memory goes to the
error-protection state.
Bit 7
FLER
Description
0
Flash memory is operating normally
Flash memory program/erase protection (error protection) is disabled
[Clearing condition]
Reset (RES pin or WDT reset) or hardware standby mode
1
(Initial value)
An error occurred during flash memory programming/erasing
Flash memory program/erase protection (error protection) is enabled
[Setting conditions]
•
When flash memory is read during programming/erasing (including a vector read
or instruction fetch, but excluding a read of the RAM area overlapping flash
memory space)
•
Immediately after the start of exception handling during programming/erasing
(excluding reset, illegal instruction, trap instruction, and division-by-zero
exception handling)
•
When a SLEEP instruction (including software standby) is executed during
programming/erasing
•
When the bus is released during programming/erasing
Bits 6 to 0—Reserved: These bits are always read as 0.
18.3.3
Erase Block Register 1 (EBR1)
Bit
7
6
5
4
3
2
1
0
EB7
EB6
EB5
EB4
EB3
EB2
EB1
EB0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
EBR1 is an 8-bit register that specifies the flash memory erase area block by block. EBR1 is
initialized to H'00 by a reset, in hardware standby mode and software standby mode, when a low
level is input to the FWE pin, and when a high level is input to the FWE pin and the SWE bit in
FLMCR1 is not set. When a bit in EBR1 is set to 1, the corresponding block can be erased. Other
blocks are erase-protected. Only one bit can be set in EBR1 and EBR2 together; do not set two or
Rev. 3.00 Sep 14, 2005 page 605 of 910
REJ09B0258-0300
Section 18 Flash Memory
more bits at the same time. When the on-chip flash memory is disabled, a read access to this
register will return H'00, and erasing is disabled.
The flash memory block configuration is shown in table 18.4. To erase the entire flash memory,
each block must be erased in turn.
As the H8/3068F-ZTAT does not support on-board programming modes in mode 6, EBR1
register bits cannot be set to 1 in this mode.
18.3.4
Erase Block Register 2 (EBR2)
Bit
7
6
5
4
3
2
1
0
—
—
EB13
EB12
EB11
EB10
EB9
EB8
Initial value
0
0
0
0
0
0
0
0
Read/Write
R
R
R/W
R/W
R/W
R/W
R/W
R/W
EBR2 is an 8-bit register that specifies the flash memory erase area block by block. EBR2 is
initialized to H'00 by a reset, in hardware standby mode and software standby mode, and when a
low level is input to the FWE pin. When a high level is input to the FWE pin and the SWE bit in
FLMCR1 is not set, it is initialized to bit 0. When a bit in EBR2 is set to 1, the corresponding
block can be erased. Other blocks are erase-protected. Only one bit can be set in EBR1 and EBR2
together; do not set two or more bits at the same time. When the on-chip flash memory is
disabled, a read will return H'00, and erasing is disabled.
The flash memory block configuration is shown in table 18.4. To erase the entire flash memory,
each block must be erased in turn.
As the H8/3068F-ZTAT does not support on-board programming modes in mode 6, EBR2
register bits cannot be set to 1 in this mode.
Note: Bits 7 and 4 in this register are read-only. These bits must not be set to 1. If bits 7 and 4
are set when an EBR1/EBR2 bit is set, EBR1/EBR2 will be initialized to H'00.
Rev. 3.00 Sep 14, 2005 page 606 of 910
REJ09B0258-0300
Section 18 Flash Memory
Table 18.4 Flash Memory Erase Blocks
Block (Size)
Addresses
EB0 (4 kbytes)
H'000000 to H'000FFF
EB1 (4 kbytes)
H'001000 to H'001FFF
EB2 (4 kbytes)
H'002000 to H'002FFF
EB3 (4 kbytes)
H'003000 to H'003FFF
EB4 (4 kbytes)
H'004000 to H'004FFF
EB5 (4 kbytes)
H'005000 to H'005FFF
EB6 (4 kbytes)
H'006000 to H'006FFF
EB7 (4 kbytes)
H'007000 to H'007FFF
EB8 (32 kbytes)
H'008000 to H'00FFFF
EB9 (64 kbytes)
H'010000 to H'01FFFF
EB10 (64 kbytes)
H'020000 to H'02FFFF
EB11 (64 kbytes)
H'030000 to H'03FFFF
EB12 (64 kbytes)
H'040000 to H'04FFFF
EB13 (64 kbytes)
H'050000 to H'05FFFF
18.3.5
RAM Control Register (RAMCR)
Bit
7
6
5
4
3
2
1
0
—
—
—
—
RAMS
RAM2
RAM1
RAM0
Initial value
1
1
1
1
0
0
0
0
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
RAMCR specifies the area of flash memory to be overlapped with part of RAM when emulating
realtime flash memory programming. RAMCR is initialized to H'00 by a reset and in hardware
standby mode. RAMCR settings should be made in user mode or user program mode.
Flash memory area divisions are shown in table 18.5. To ensure correct operation of the
emulation function, the ROM for which RAM emulation is performed should not be accessed
immediately after this register has been modified. Normal execution of an access immediately
after register modification is not guaranteed.
Bits 7 to 4—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 607 of 910
REJ09B0258-0300
Section 18 Flash Memory
Bit 3—RAM Select (RAMS): Specifies selection or non-selection of flash memory emulation in
RAM. When RAMS = 1, all flash memory blocks are program/erase-protected.
Bit 3
RAMS
Description
0
Emulation not selected
Program/erase-protection of all flash memory blocks is disabled
1
(Initial value)
Emulation selected
Program/erase-protection of all flash memory blocks is enabled
Bits 2 to 0—Flash Memory Area Selection (RAM2 to RAM0): These bits are used together
with bit 3 to select the flash memory area to be overlapped with RAM. (See table 18.5.)
Table 18.5 Flash Memory Area Divisions
RAM Area
Block Name
RAMS
RAM2
RAM1
RAM0
H'FFE000 to H'FFEFFF
4-kbyte RAM area
0
*
*
*
H'000000 to H'000FFF
EB0 (4 kbytes)
1
0
0
0
H'001000 to H'001FFF
EB1 (4 kbytes)
1
0
0
1
H'002000 to H'002FFF
EB2 (4 kbytes)
1
0
1
0
H'003000 to H'003FFF
EB3 (4 kbytes)
1
0
1
1
H'004000 to H'004FFF
EB4 (4 kbytes)
1
1
0
0
H'005000 to H'005FFF
EB5 (4 kbytes)
1
1
0
1
H'006000 to H'006FFF
EB6 (4 kbytes)
1
1
1
0
H'007000 to H'007FFF
EB7 (4 kbytes)
1
1
1
1
*: Don’t care
Note: Flash memory emulation by RAM is not supported in mode 6 (single-chip normal mode);
therefore, although these bits can be written, they should not be set to 1.
When performing flash memory emulation by RAM, the RAME bit in SYSCR must be set to
1.
Rev. 3.00 Sep 14, 2005 page 608 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.4
Overview of Operation
18.4.1
Mode Transitions
When the mode pins and the FWE pin are set in the reset state and a reset-start is executed, the
H8/3068F-ZTAT enters one of the operating modes shown in figure 18.2. In user mode, flash
memory can be read but not programmed or erased.
Flash memory can be programmed and erased in boot mode, user program mode, and PROM
mode.
Boot mode and user program mode cannot be used in the H8/3068F-ZTAT’s mode 6 (normal
mode with on-chip ROM enabled).
Rev. 3.00 Sep 14, 2005 page 609 of 910
REJ09B0258-0300
Section 18 Flash Memory
Reset state
*3
*1
User mode
with on-chip ROM
enabled
RES = 0
RES = 0
*2
*4
RES = 0
FWE = 0
*5
RES = 0
*4
PROM mode
User program
mode
*1
Boot mode
On-board programming mode
Notes: Only make a transition between user mode and user program mode when the CPU is not
accessing the flash memory.
1. RAM emulation possible
2. The H8/3068F-ZTAT is placed in PROM mode by means of a dedicated PROM writer.
3. MD2, MD1, MD0 = (1, 0, 1) (1, 1, 0) (1, 1, 1)
FWE = 0
4. MD2, MD1, MD0 = (1, 0, 1) (1, 1, 1)
FWE = 1
5. MD2, MD1, MD0 (0, 0, 1) (0, 1, 1)
FWE = 1
Figure 18.2 Flash Memory Related State Transitions
State transitions between the normal and user modes and on-board programming mode are
performed by changing the FWE pin level from high to low or from low to high. To prevent
misoperation (erroneous programming or erasing) in these cases, the bits in the flash memory
control register (FLMCR1) should be cleared to 0 before making such a transition. After the bits
are cleared, a wait time is necessary. Normal operation is not guaranteed if this wait time is
insufficient.
Rev. 3.00 Sep 14, 2005 page 610 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.4.2
On-Board Programming Modes
Example of Boot Mode Operation
1. Initial state
The old program version or data remains
written in the flash memory. The user should
prepare the programming control program and
new application program beforehand in the
host.
Host
2. Programming control program transfer
When boot mode is entered, the boot program
in the H8/3068F-ZTAT (originally incorporated
in the chip) is started and the programming
control program in the host is transferred to
RAM via SCI communication. The boot
program required for flash memory erasing is
automatically transferred to the RAM boot
program area.
Host
Programming control
program
New application
program
New application
program
H8/3068F-ZTAT
H8/3068F-ZTAT
SCI
Boot program
Flash memory
SCI
Boot program
Flash memory
RAM
RAM
Boot program area
Application
program
(old version)
Application
program
(old version)
3. Flash memory initialization
The erase program in the boot program area
(in RAM) is executed, and the flash memory is
initialized (to H'FF). In boot mode, total flash
memory erasure is performed, without regard
to blocks.
Host
Programming control
program
4. Writing new application program
The programming control program transferred
from the host to RAM is executed, and the new
application program in the host is written into
the flash memory.
Host
New application
program
H8/3068F-ZTAT
H8/3068F-ZTAT
SCI
Boot program
Flash memory
RAM
Flash memory
Boot program area
Flash memory
prewrite-erase
Programming control
program
SCI
Boot program
RAM
Boot program area
New application
program
Programming control
program
Program execution state
Rev. 3.00 Sep 14, 2005 page 611 of 910
REJ09B0258-0300
Section 18 Flash Memory
Example of User Program Mode Operation
1. Initial state
The FWE assessment program that confirms
that user program mode has been entered, and
the program that will transfer the programming/
erase control program from flash memory to
on-chip RAM should be written into the flash
memory by the user beforehand. The
programming/erase control program should be
prepared in the host or in the flash memory.
2. Programming/erase control program transfer
When user program mode is entered, user
software recognizes this fact, executes the
transfer program in the flash memory, and
transfers the programming/erase control
program to RAM.
Host
Host
Programming/erase
control program
New application
program
New application
program
H8/3068F-ZTAT
H8/3068F-ZTAT
SCI
Boot program
Flash memory
Flash memory
RAM
SCI
Boot program
FWE assessment program
FWE assessment program
Transfer program
Transfer program
RAM
Programming/erase
control program
Application program
(old version)
Application program
(old version)
3. Flash memory initialization
The programming/erase program in RAM is
executed, and the flash memory is initialized (to
H'FF). Erasing can be performed in block units,
but not in byte units.
4. Writing new application program
Next, the new application program in the host is
written into the erased flash memory blocks.
Do not write to unerased blocks.
Host
Host
New application
program
H8/3068F-ZTAT
H8/3068F-ZTAT
SCI
Boot program
Flash memory
RAM
Flash memory
FWE assessment program
FWE assessment program
Transfer program
Transfer program
Programming/erase
control program
Flash memory
erase
SCI
Boot program
RAM
Programming/erase
control program
New application
program
Program execution state
Rev. 3.00 Sep 14, 2005 page 612 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.4.3
Flash Memory Emulation in RAM
In the H8/3068F-ZTAT, flash memory programming can be emulated in real time by overlapping
the flash memory with part of RAM (“overlap RAM”). When the emulation block set in RAMCR
is accessed while the emulation function is being executed, data written in the overlap RAM is
read.
Emulation should be performed in user mode or user program mode.
SCI
Flash memory
RAM
Emulation block
Overlap RAM
Application program
(Emulation is performed on data written
in RAM)
Execution state
Figure 18.3 Reading Overlap RAM Data in User Mode/User Program Mode
When overlap RAM data is confirmed, clear the RAMS bit to cancel RAM overlap, and actually
perform writes to the flash memory in user program mode.
When the programming control program is transferred to RAM in on-board programming mode,
ensure that the transfer destination and the overlap RAM do not overlap, as this will cause data in
the overlap RAM to be rewritten.
Rev. 3.00 Sep 14, 2005 page 613 of 910
REJ09B0258-0300
Section 18 Flash Memory
SCI
Flash memory
RAM
Program data
Application program
Overlap RAM
(program data)
Programming control program
Execution state
Figure 18.4 Writing Overlap RAM Data in User Program Mode
Rev. 3.00 Sep 14, 2005 page 614 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.4.4
Block Configuration
The flash memory in the H8/3068F-ZTAT is divided into three 64-kbyte blocks, one 32-kbyte
block, and eight 4-kbyte blocks. Erasing can be carried out in block units.
Address H'00000
4 kbytes × 8
32 kbytes
64 kbytes
64 kbytes
384 kbytes
64 kbytes
64 kbytes
64 kbytes
Address H'5FFFF
Rev. 3.00 Sep 14, 2005 page 615 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.5
On-Board Programming Mode
When pins are set to on-board programming mode and a reset-start is executed, the chip enters
the on-board programming state in which on-chip flash memory programming, erasing, and
verifying can be carried out. There are two operating modes in this mode—boot mode and user
program mode. The pin settings for entering each mode are shown in table 18.6. For a diagram of
the transitions to the various flash memory modes, see figure 18.2.
Boot mode and user program mode cannot be used in the H8/3068F-ZTAT’s mode 6 (on-chip
ROM enabled).
Table 18.6 On-Board Programming Mode Settings
Mode
Boot mode
User program mode
FWE
Mode 5
1
1*
MD2
MD1
MD0
2
0
1
2
0*
Mode 7
0*
1
1
Mode 5
1
0
1
Mode 7
1
1
1
Notes: 1. For the High level input timing, see items 6 and 7 of Notes on Using the Boot Mode.
2. In boot mode, the MD2 setting should be the inverse of the input.
In the boot mode in the H8/3068F-ZTAT, the levels of the mode pins (MD2 to MD0) are
reflected in mode select bits 2 to 0 (MDS2 to MDS0) in the mode control register
(MDCR).
Rev. 3.00 Sep 14, 2005 page 616 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.5.1
Boot Mode
When boot mode is used, a flash memory programming control program must be prepared
beforehand in the host, and SCI channel 1, which is to be used, must be set to asynchronous
mode.
When a reset-start is executed after setting the H8/3068F-ZTAT’ pins to boot mode, the boot
program already incorporated in the MCU is activated, and the programming control program
prepared beforehand in the host is transmitted sequentially to the H8/3068F-ZTAT, using the SCI.
In the H8/3068F-ZTAT, the programming control program received via the SCI is written into the
programming control program area in on-chip RAM. After the transfer is completed, control
branches to the start address (H'FFC720) of the programming control program area and the
programming control program execution state is entered (flash memory programming/erasing can
be performed).
Figure 18.5 shows a system configuration diagram when using boot mode, and figure 18.6 shows
the boot program mode execution procedure.
H8/3068F-ZTAT
Flash memory
Host
Reception of programming data
Transmission of verify data
RxD1
SCI1
TxD1
On-chip RAM
Figure 18.5 System Configuration When Using Boot Mode
Rev. 3.00 Sep 14, 2005 page 617 of 910
REJ09B0258-0300
Section 18 Flash Memory
Start
Set pins to boot program mode and execute reset-start
Host transfers data (H'00) continuously at prescribed
bit rate
H8/3068F-ZTAT measures low period of H'00 data
transmitted by host
H8/3068F-ZTAT calculates bit rate and sets value in bit
rate register
After bit rate adjustment, H8/3068F-ZTAT transmits one
H'00 data byte to host to indicate end of adjustment
Host confirms normal reception of bit rate adjustment
end indication (H'00), and transmits one H'55 data byte
After receiving H'55, H8/3068F-ZTAT transmits one
H'AA byte to host
Host transmits number of programming control program
bytes (N), upper byte followed by lower byte
H8/3068F-ZTAT transmits received number of bytes to
host as verify data (echo-back)
n=1
Host transmits programming control program
sequentially in byte units
H8/3068F-ZTAT transmits received programming
control program to host as verify data (echo-back)
n+1→n
Transfer received programming control program to
on-chip RAM
n = N?
No
Yes
End of transmission
Check flash memory data, and if data has already been
written, erase all blocks
After confirming that all flash memory data has been
erased, H8/3068F-ZTAT transmits one H'AA byte to
host
Execute programming control program transferred to
on-chip RAM
Note: If a memory cell does not operate normally and cannot be erased, one H'FF byte is transmitted as an erase error
indication, and the erase operation and subsequent operations are halted.
Figure 18.6 Boot Mode Execution Procedure
Rev. 3.00 Sep 14, 2005 page 618 of 910
REJ09B0258-0300
Section 18 Flash Memory
Automatic SCI Bit Rate Adjustment:
Start
bit
D0
D1
D2
D3
D4
D5
D6
Low period (9 bits) measured (H'00 data)
D7
Stop
bit
High period
(1 or more bits)
When boot mode is initiated, the H8/3068F-ZTAT measures the low period of the asynchronous
SCI communication data (H'00) transmitted continuously from the host. The SCI transmit/receive
format should be set as 8-bit data, 1 stop bit, no parity. The H8/3068F-ZTAT calculates the bit
rate of the transmission from the host from the measured low period, and transmits one H'00 byte
to the host to indicate the end of bit rate adjustment. The host should confirm that this adjustment
end indication (H'00) has been received normally, and transmit one H'55 byte to the H8/3068FZTAT. If reception cannot be performed normally, initiate boot mode again (reset), and repeat the
above operations. Depending on the host’s transmission bit rate and the H8/3068F-ZTAT’s
system clock frequency, there will be a discrepancy between the bit rates of the host and the
H8/3068F-ZTAT. To ensure correct SCI operation, the host’s transfer bit rate should be set to
4800, 9600, or 19,200 bps*.
Table 18.7 shows typical host transfer bit rates and system clock frequencies for which automatic
adjustment of the H8/3068F-ZTAT bit rate is possible. The boot program should be executed
within this system clock range.
Table 18.7 System Clock Frequencies for which Automatic Adjustment of H8/3068FZTAT Bit Rate is Possible
Host Bit Rate (bps)
System Clock Frequency for which Automatic
Adjustment of H8/3068F-ZTAT Bit Rate is Possible (MHz)
19,200
16 to 25
9,600
8 to 25
4,800
4 to 25
Note: * Only use a setting of 4800, 9600, or 19200 bps for the host’s bit rate. No other settings
can be used.
Although the H8/3068F-ZTAT may also perform automatic bit rate adjustment with bit
rate and system clock combinations other than those shown in table 18.7, a degree of
error will arise between the bit rates of the host and the H8/3068F-ZTAT, and subsequent
transfer will not be performed normally. Therefore, only a combination of bit rate and
Rev. 3.00 Sep 14, 2005 page 619 of 910
REJ09B0258-0300
Section 18 Flash Memory
system clock frequency within one of the ranges shown in table 18.7 can be used for boot
mode execution.
On-Chip RAM Area Divisions in Boot Mode: In boot mode, the RAM area is divided into an
area used by the boot program and an area to which the user program is transferred via the SCI, as
shown in figure 18.7. The boot program area becomes available when a transition is made to the
execution state for the user program transferred to RAM.
H'FFBF20
Boot program
area
H'FFC71F
H'FFC720
User program
transfer area
H'FFFF1F
Note: The boot program area cannot be used until a transition is made to the execution state
for the user program transferred to RAM. Note also that the boot program remains in
this area in RAM even after control branches to the user program.
Figure 18.7 RAM Areas in Boot Mode
Notes on Use of Boot Mode:
1. When the H8/3068F-ZTAT chip comes out of reset in boot mode, it measures the low period
of the input at the SCI’s RxD1 pin. The reset should end with RxD1 high. After the reset ends,
it takes about 100 states for the chip to get ready to measure the low period of the RxD1 input.
2. In boot mode, if any data has been programmed into the flash memory (if all data is not 1), all
flash memory blocks are erased. Boot mode is for use when user program mode is
unavailable, such as the first time on-board programming is performed, or if the program
activated in user program mode is accidentally erased.
3. Interrupts cannot be used while the flash memory is being programmed or erased.
4. The RxD1 and TxD1 lines should be pulled up on the board.
5. Before branching to the user program the H8/3068F-ZTAT terminates transmit and receive
operations by the on-chip SCI (channel 1) (by clearing the RE and TE bits to 0 in the serial
Rev. 3.00 Sep 14, 2005 page 620 of 910
REJ09B0258-0300
Section 18 Flash Memory
control register (SCR)), but the adjusted bit rate value remains set in the bit rate register
(BRR). The transmit data output pin, TxD1, goes to the high-level output state (P91DDR = 1 in
P9DDR, P91DR = 1 in P9DR).
The contents of the CPU’s internal general registers are undefined at this time, so these
registers must be initialized immediately after branching to the user program. In particular,
since the stack pointer (SP) is used implicitly in subroutine calls, etc., a stack area must be
specified for use by the user program.
The initial values of other on-chip registers are not changed.
6. Boot mode can be entered by setting pins MD0 to MD2 and FWE in accordance with the mode
setting conditions shown in table 18.6, and then executing a reset-start.
a. When switching from boot mode to normal mode, the boot mode state within the chip
must first be cleared by reset input via the RES pin*1. The RES pin must be held low for at
least 20 system clock cycles.*3
b. Do not change the input levels of the mode pins (MD2 to MD0) or the FWE pin in boot
mode. To change the mode, the RES pin must first be driven low to set the reset state.
Also, if a watchdog timer reset occurs in the boot mode state, the MCU’s internal state will
not be cleared, and the on-chip boot program will be restarted regardless of the mode pin
states.
c. The FWE pin must not be driven low while the boot program is running or flash memory is
being programmed or erased*2.
7. If the mode pin input levels are changed (for example, from low to high) during a reset, the
state of ports with multiplexed address functions and bus control output signals (CSn, AS,
RD, LWR, HWR) may also change according to the change in the MCU’s operating mode.
Therefore, care must be taken to make pin settings to prevent these pins from being used
directly as output signal pins during a reset, or to prevent collision with signals outside the
MCU.
Rev. 3.00 Sep 14, 2005 page 621 of 910
REJ09B0258-0300
Section 18 Flash Memory
H8/3068F-ZTAT
CSn
MD2
MD1
MD0
FWE
External
memory,
etc.
System
control
unit
RES
Notes: 1. Mode pin and FWE pin input must satisfy the mode programming setup time (tMDS)
with respect to the reset release timing.
2. For further information on FWE application and disconnection, see section 18.11,
Flash Memory Programming and Erasing Precautions.
3. See section 4.2.2, Reset Sequence, and section 18.11, Flash Memory Programming
and Erasing Precautions. The H8/3068F-ZTAT requires a minimum of 20 system
clock cycles for a reset during operation.
18.5.2
User Program Mode
When set to user program mode, the H8/3068F-ZTAT can program and erase its flash memory by
executing a user program/erase control program. Therefore, on-board reprogramming of the onchip flash memory can be carried out by providing on-board means of FWE control and supply of
programming data, and storing a program/erase control program in part of the program area as
necessary.
To select user program mode, select a mode that enables the on-chip ROM (mode 5 or 7), and
apply a high level to the FWE pin. In this mode, on-chip supporting modules other than flash
memory operate as they normally would in modes 5 and 7.
Flash memory programming/erasing should not be carried out in mode 6. When mode 6 is set, the
FWE pin must be driven low.
The flash memory itself cannot be read while being programmed or erased, so the program that
performs programming should be placed in external memory or transferred to RAM and executed
there.
Rev. 3.00 Sep 14, 2005 page 622 of 910
REJ09B0258-0300
Section 18 Flash Memory
Figure 18.8 shows the execution procedure when user program mode is entered during program
execution in RAM. It is also possible to start from user program mode in a reset-start.
Write FWE assessment program and transfer
program (and programming/erase control
program if necessary) beforehand
MD2–MD0 = 101 or 111
Reset-start
Transfer programming/erase control
program to RAM
Branch to programming/erase control
program in RAM area
FWE = high
(user program mode)
Execute programming/erase control
program in RAM
(flash memory rewriting)
Clear SWE bit, then release FWE
(user program mode clearing)
Branch to application program
in flash memory
Notes: 1. Do not apply a constant high level to the FWE pin. A high level should be applied to the
FWE pin only when programming or erasing flash memory (including execution of flash
memory emulation by RAM). Also, while a high level is applied to the FWE pin, the
watchdog timer should be activated to prevent overprogramming or overerasing due to
program runaway, etc.
2. For further information on FWE application and disconnection, see section 18.11, Flash
Memory Programming and Erasing Precautions.
3. In order to execute a normal read of flash memory in user program mode, the
programming/erase program must not be executing. It is thus necessary to ensure that
bits 6 to 0 in FLMCR1 are cleared to 0.
Figure 18.8 Example of User Program Mode Execution Procedure
Rev. 3.00 Sep 14, 2005 page 623 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.6
Flash Memory Programming/Erasing
A software method, using the CPU, is employed to program and erase flash memory in the onboard programming modes. There are four flash memory operating modes: program mode, erase
mode, program-verify mode, and erase-verify mode. Transitions to these modes for addresses
H'000000 to H'03FFFF are made by setting the PSU, ESU, P, E, PV, and EV bits in FLMCR1.
The flash memory cannot be read while being programmed or erased. Therefore, the program
(user program) that controls flash memory programming/erasing should be located and executed
in on-chip RAM or external memory.
See section 18.11, Flash Memory Programming and Erasing Precautions, for points to be noted
when programming or erasing the flash memory. In the following operation descriptions, wait
times after setting or clearing individual bits in FLMCR1 are given as parameters; for details of
the wait times, see section 21.1.6, Flash Memory Characteristics.
Notes: 1. Operation is not guaranteed if setting/resetting of the SWE, ESU, PSU, EV, PV, E, and
P bits in FLMCR1 is executed by a program in flash memory.
2. When programming or erasing, set FWE to 1 (programming/erasing will not be
executed if FWE = 0).
3. Programming must be executed in the erased state. Do not perform additional
programming on addresses that have already been programmed.
Rev. 3.00 Sep 14, 2005 page 624 of 910
REJ09B0258-0300
Section 18 Flash Memory
*3
E=1
Erase setup
state
Erase mode
E=0
Normal mode
FWE = 1
ESU = 1
ESU = 0
*1
FWE = 0
EV = 1
*2
On-board
SWE = 1
Software
programming mode
programming
Software programming
enable
disable state
SWE = 0
state
Erase-verify
mode
EV = 0
PSU = 1
*4
P=1
PSU = 0
Program
setup state
Program mode
P=0
PV = 1
PV = 0
Program-verify
mode
Notes: In order to perform a normal read of flash memory, SWE must be cleared to 0. Also note that verify-reads
can be performed during the programming/erasing process.
1.
: Normal mode
: On-board programming mode
2. Do not make a state transition by setting or clearing multiple bits simultaneously.
3. After a transition from erase mode to the erase setup state, do not enter erase mode without passing
through the software programming enable state.
4. After a transition from program mode to the program setup state, do not enter program mode without
passing through the software programming enable state.
Figure 18.9 FLMCR1 Bit Settings and State Transitions
Rev. 3.00 Sep 14, 2005 page 625 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.6.1
Program Mode
When writing data or programs to flash memory, the program/program-verify flowchart shown in
figure 18.10 should be followed. Performing programming operations according to this flowchart
will enable data or programs to be written to flash memory without subjecting the device to
voltage stress or sacrificing program data reliability. Programming should be carried out 128
bytes at a time.
The wait times after bits are set or cleared in the flash memory control register 1 (FLMCR1) and
the maximum number of programming operations (N) are shown in table 21.10 in section 21.1.6,
Flash Memory Characteristics.
Following the elapse of (tsswe) µs or more after the SWE bit is set to 1 in FLMCR1, 128-byte data
is written consecutively to the write addresses. The lower 8 bits of the first address written to
must be H'00 and H'80, 128 consecutive byte data transfers are performed. The program address
and program data are latched in the flash memory. A 128-byte data transfer must be performed
even if writing fewer than 128 bytes; in this case, H'FF data must be written to the extra
addresses.
Next, the watchdog timer (WDT) is set to prevent overprogramming due to program runaway, etc.
Set a value greater than (tspsu + tsp + tcp + tcpsu) µs as the WDT overflow period. Preparation for
entering program mode (program setup) is performed next by setting the PSU bit in FLMCR1.
The operating mode is then switched to program mode by setting the P bit in FLMCR1 after the
elapse of at least (tspsu) µs. The time during which the P bit is set is the flash memory
programming time. Make a program setting so that the time for one programming operation is
within the range of (tsp) µs.
The wait time after P bit setting must be changed according to the degree of progress through the
programming operation. For details see “Notes on Program/Program-Verify Mode.”
Rev. 3.00 Sep 14, 2005 page 626 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.6.2
Program-Verify Mode
In program-verify mode, the data written in program mode is read to check whether it has been
correctly written in the flash memory.
After the elapse of the given programming time, clear the P bit in FLMCR1, then wait for at least
(tcp) µs before clearing the PSU bit to exit program mode. After exiting program mode, the
watchdog timer setting is also cleared. The operating mode is then switched to program-verify
mode by setting the PV bit in FLMCR1. Before reading in program-verify mode, a dummy write
of H'FF data should be made to the addresses to be read. The dummy write should be executed
after the elapse of (tspv) µs or more. When the flash memory is read in this state (verify data is
read in 16-bit units), the data at the latched address is read. Wait at least (tspvr) µs after the dummy
write before performing this read operation. Next, the originally written data is compared with the
verify data, and reprogram data is computed (see figure 18.10) and transferred to RAM. After
verification of 128 bytes of data has been completed, exit program-verify mode, wait for at least
(tcpv) µs, then clear the SWE bit in FLMCR1. If reprogramming is necessary, set program mode
again, and repeat the program/program-verify sequence as before. The maximum number of
repetitions of the program/program-verify sequence is indicated by the maximum programming
count (N). Leave a wait time of at least (tcswe) µs after clearing SWE.
Notes on Program/Program-Verify Procedure
1. The program/program-verify procedure for the H8/3068F-ZTAT uses a 128-byte-unit
programming algorithm.
In order to perform 128-byte-unit programming, the lower 8 bits of the write start address
must be H'00 or H'80.
2. When performing continuous writing of 128-byte data to flash memory, byte-unit transfer
should be used.
128-byte data transfer is necessary even when writing fewer than 128 bytes of data. Write
H'FF data to the extra addresses.
3. Verify data is read in word units.
4. The write pulse is applied and a flash memory write executed while the P bit in FLMCR1 is
set. In the H8/3068F-ZTAT, write pulses should be applied as follows in the
program/program-verify procedure to prevent voltage stress on the device and loss of write
data reliability.
a. After write pulse application, perform a verify-read in program-verify mode and apply a
write pulse again for any bits read as 1 (reprogramming processing). When all the 0-write
bits in the 128-byte write data are read as 0 in the verify-read operation, the
program/program-verify procedure is completed. In the H8/3068F-ZTAT, the number of
Rev. 3.00 Sep 14, 2005 page 627 of 910
REJ09B0258-0300
Section 18 Flash Memory
loops in reprogramming processing is guaranteed not to exceed the maximum value of the
maximum programming count (N).
b. After write pulse application, a verify-read is performed in program-verify mode, and
programming is judged to have been completed for bits read as 0. The following
processing is necessary for programmed bits.
When programming is completed at an early stage in the program/program-verify
procedure:
If programming is completed in the 1st to 6th reprogramming processing loop, additional
programming should be performed on the relevant bits. Additional programming should
only be performed on bits which first return 0 in a verify-read in certain reprogramming
processing.
When programming is completed at a late stage in the program/program-verify procedure:
If programming is completed in the 7th or later reprogramming processing loop, additional
programming is not necessary for the relevant bits.
c. If programming of other bits is incomplete in the 128 bytes, reprogramming processing
should be executed. If a bit for which programming has been judged to be completed is
read as 1 in a subsequent verify-read, a write pulse should again be applied to that bit.
5. The period for which the P bit in FLMCR1 is set (the write pulse width) should be changed
according to the degree of progress through the program/program-verify procedure. For
detailed wait time specifications, see section 21.1.6, Flash Memory Characteristics.
Item
Symbol
Item
Symbol
Wait time after P
bit setting
tsp
When reprogramming loop count (n) is 1 to 6
tsp30
When reprogramming loop count (n) is 7 or more
tsp200
In case of additional programming processing*
tsp10
Note: * Additional programming processing is necessary only when the reprogramming loop count
(n) is 1 to 6.
6. The program/program-verify flowchart for the H8/3068F-ZTAT is shown in figure 18.10.
To cover the points noted above, bits on which reprogramming processing is to be executed,
and bits on which additional programming is to be executed, must be determined as shown
below.
Since reprogram data and additional-programming data vary according to the progress of the
programming procedure, it is recommended that the following data storage areas (128 bytes
each) be provided in RAM.
Rev. 3.00 Sep 14, 2005 page 628 of 910
REJ09B0258-0300
Section 18 Flash Memory
Reprogram Data Computation Table
(D)
Result of Verify-Read
after Write Pulse
(X)
Application (V)
Result of Operation
0
0
1
Programming completed: reprogramming
processing not to be executed
0
1
0
Programming incomplete: reprogramming
processing to be executed
1
0
1

1
1
1
Still in erased state: no action
Comments
Legend
(D): Source data of bits on which programming is executed
(X): Source data of bits on which reprogramming is executed
Additional-Programming Data Computation Table
Result of Verify-Read
after Write Pulse
(Y)
(X') Application (V)
Result of Operation
Comments
0
0
0
Programming by write pulse application
judged to be completed: additional
programming processing to be executed
0
1
1
Programming by write pulse application
incomplete: additional programming
processing not to be executed
1
0
1
Programming already completed: additional
programming processing not to be executed
1
1
1
Still in erased state: no action
Legend
(Y): Data of bits on which additional programming is executed
(X'): Data of bits on which reprogramming is executed in a certain reprogramming loop
7. It is necessary to execute additional programming processing during the course of the
H8/3068F-ZTAT program/program-verify procedure. However, once 128-byte-unit
programming is finished, additional programming should not be carried out on the same
address area. When executing reprogramming, an erase must be executed first. Note that
normal operation of reads, etc., is not guaranteed if additional programming is performed on
addresses for which a program/program-verify operation has finished.
Rev. 3.00 Sep 14, 2005 page 629 of 910
REJ09B0258-0300
Section 18 Flash Memory
Start of programming
Write pulse application subroutine
Perform programming in the erased state.
Do not perform additional programming
on previously programmed addresses.
START
Sub-Routine Write Pulse
Set SWE bit in FLMCR1
WDT enable
Wait (tsswe) µs
Set PSU bit in FLMCR1
Wait (tspsu) µs
*7
*4
n= 1
Start of programming
Set P bit in FLMCR1
*7
Store 128-byte program data in program
data area and reprogram data area
m= 0
Wait (tsp) µs
*5*7
Clear P bit in FLMCR1
Programming halted
Consecutively write 128-byte data in reprogram
data area in RAM to flash memory
*1
Sub-Routine-Call
Wait (tcp) µs
Set PV bit in FLMCR1
Clear PSU bit in FLMCR1
Wait (tcpsu) µs
See Note *6 for pulse width
Write pulse
*7
Wait (tspv) µs
*7
*7
H'FF dummy write to verify address
Disable WDT
Wait (tspvr) µs
End Sub
n←n+1
*7
Read verify data
*2
Write data =
verify data?
NG
Increment address
Note: 6. Write Pulse Width
Number of Writes (n)
Write Time (tsp) µsec
1
2
3
4
5
6
7
8
9
10
11
12
13
30
30
30
30
30
30
200
200
200
200
200
200
200
998
999
1000
200
200
200
m=1
OK
NG
6≥n?
OK
Additional-programming data computation
Transfer additional-programming data to
additional-programming data area
*4
*3
Reprogram data computation
Transfer reprogram data to reprogram data area
NG
*4
128-byte
data verification completed?
OK
Clear PV bit in FLMCR1
Reprogram
Wait (tcpv) µs
Note: Use a 10 µs write pulse for additional programming.
*7
NG
6 ≥ n?
OK
Consecutively write 128-byte data in additionalprogramming data area in RAM to flash memory
RAM
Program data storage
area (128 bytes)
*1
Sub-Routine-Call
Write Pulse (Additional programming)
Reprogram data storage
area (128 bytes)
*7
NG
m= 0 ?
OK
Clear SWE bit in FLMCR1
Additional-programming
data storage area
(128 bytes)
NG
n ≥ N?
OK
Clear SWE bit in FLMCR1
Wait (tcswe) µs
Wait (tcswe) µs
End of programming
Programming failure
*7
Notes: 1. Data transfer is performed by byte transfer. The lower 8 bits of the first address written to must be H'00 or H'80.
A 128-byte data transfer must be performed even if writing fewer than 128 bytes; in this case, H'FF data must be written to the extra addresses.
2. Verify data is read in 16-bit (word) units.
3. Reprogram data is determined by the operation shown in the table below (comparison between the data stored in the program data area and the verify data). Bits for
which the reprogram data is 0 are programmed in the next reprogramming loop. Therefore, even bits for which programming has been completed will be subjected to
programming once again if the result of the subsequent verify operation is NG.
4. A 128-byte area for storing program data, a 128-byte area for storing reprogram data, and a 128-byte area for storing additional-programming data must be provided in
RAM. The contents of the reprogram data area and additional-programming data area are modified as programming proceeds.
5. A write pulse of 30 µs or 200 µs is applied according to the progress of the programming operation. See Note 6 for details of the pulse widths. When writing of
additional-programming data is executed, a 10 µs write pulse should be applied. Reprogram data X' means reprogram data when the write pulse is applied.
7. The wait times and value of N are shown in section 21.1.6, Flash Memory Characteristics.
Reprogram Data Computation Table
Additional-Programming Data Computation Table
Original Data
Verify Data
Reprogram Data
(D)
0
(V)
0
(X)
1
0
1
0
1
0
1
1
1
1
Comments
Reprogram Data
(X')
Verify Data
Additional(V)
Programming Data (Y)
Programming completed
0
0
0
Programming incomplete;
reprogram
0
1
1
1
0
1
1
1
1
Still in erased state; no action
Comments
Additional programming
to be executed
Additional programming
not to be executed
Additional programming
not to be executed
Additional programming
not to be executed
Figure 18.10 Program/Program-Verify Flowchart (128-Byte Programming)
Rev. 3.00 Sep 14, 2005 page 630 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.6.3
Erase Mode
When erasing flash memory, the single-block erase flowchart shown in figure 18.11 should be
followed.
The wait times after bits are set or cleared in the flash memory control register 1 (FLMCR1) and
the maximum number of erase operations (N) are shown in table 21.10 in section 21.1.6, Flash
Memory Characteristics.
To erase flash memory contents, make a 1-bit setting for the flash memory area to be erased in
erase block register 1 and 2 (EBR1, EBR2) at least (tsswe) µs after setting the SWE bit to 1 in
FLMCR1. Next, the watchdog timer (WDT) is set to prevent overerasing due to program
runaway, etc. Set a value greater than (tse) ms + (tsesu + tce + tcesu) µs as the WDT overflow period.
Preparation for entering erase mode (erase setup) is performed next by setting the ESU bit in
FLMCR1. The operating mode is then switched to erase mode by setting the E bit in FLMCR1
after the elapse of at least (tsesu) µs. The time during which the E bit is set is the flash memory
erase time. Ensure that the erase time does not exceed (tse) ms.
Note: With flash memory erasing, preprogramming (setting all memory data in the memory to
be erased to all 0) is not necessary before starting the erase procedure.
18.6.4
Erase-Verify Mode
In erase-verify mode, data is read after memory has been erased to check whether it has been
correctly erased.
After the elapse of the fixed erase time, clear the E bit in FLMCR1, then wait for at least (tce) µs
before clearing the ESU bit to exit erase mode. After exiting erase mode, the watchdog timer
setting is also cleared. The operating mode is then switched to erase-verify mode by setting the
EV bit in FLMCR1. Before reading in erase-verify mode, a dummy write of H'FF data should be
made to the addresses to be read. The dummy write should be executed after the elapse of (tsev) µs
or more. When the flash memory is read in this state (verify data is read in 16-bit units), the data
at the latched address is read. Wait at least (tsevr) µs after the dummy write before performing this
read operation. If the read data has been erased (all 1), a dummy write is performed to the next
address, and erase-verify is performed. If the read data is unerased, set erase mode again, and
repeat the erase/erase-verify sequence as before. The maximum number of repetitions of the
erase/erase-verify sequence is indicated by the maximum erase count (N). When verification is
completed, exit erase-verify mode, and wait for at least (tcev) µs. If erasure has been completed on
all the erase blocks, clear the SWE bit in FLMCR1, and leave a wait time of at least (tcswe) µs.
If erasing multiple blocks, set a single bit in EBR1/EBR2 for the next block to be erased, and
repeat the erase/erase-verify sequence as before.
Rev. 3.00 Sep 14, 2005 page 631 of 910
REJ09B0258-0300
Section 18 Flash Memory
Start
*1
Perform erasing in block units.
Set SWE bit in FLMCR1
Wait (tsswe) µs
*5
n=1
*3 *4
Set EBR1 or EBR2
Enable WDT
Set ESU bit in FLMCR1
Wait (tsesu) µs
*5
Start of erase
Set E bit in FLMCR1
Wait (tse) ms
*5
Clear E bit in FLMCR1
End of erase
Wait (tce) µs
*5
Clear ESU bit in FLMCR1
Wait (tcesu) µs
*5
Disable WDT
Set EV bit in FLMCR1
Wait (tsev) µs
n←n+1
*5
Set block start address as verify address
H'FF dummy write to verify address
Increment
address
Wait (tsevr) µs
*5
Read verify data
*2
Verify data = all 1s?
No
Yes
No
Last address of block?
Re-erase
Yes
Clear EV bit in FLMCR1
Wait (tcev) µs
Clear EV bit in FLMCR1
*5
Wait (tcev) µs
*5
*5
n ≥ N?
Yes
Clear SWE bit in FLMCR1
Clear SWE bit in FLMCR1
Wait (tcswe) µs
End of erasing
Notes: 1.
2.
3.
4.
5.
No
*5
Wait (tcswe) µs
*5
Erase failure
Prewriting (setting erase block data to all 0s) is not necessary.
Verify data is read in 16-bit (word) units.
Make only a single-bit specification in the erase block registers (EBR1 and EBR2). Two or more bits must not be set simultaneously.
Erasing is performed in block units. To erase multiple blocks, each block must be erased in turn.
The wait times and the value of N are shown in section 21.1.6, Flash Memory Characteristics.
Figure 18.11 Erase/Erase-Verify Flowchart (Single-Block Erasing)
Rev. 3.00 Sep 14, 2005 page 632 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.7
Flash Memory Protection
There are three kinds of flash memory program/erase protection: hardware, software, and error
protection.
18.7.1
Hardware Protection
Hardware protection refers to a state in which programming/erasing of flash memory is forcibly
disabled or aborted. In this state, the settings in flash memory control register 1 (FLMCR1) and
erase block registers 1 and 2 (EBR1, EBR2) are reset. In the error protection state, the FLMCR1,
EBR1, and EBR2 settings are retained; the P bit and E bit can be set, but a transition is not made
to program mode or erase mode. (See table 18.8.)
Table 18.8 Hardware Protection
Function
Item
Description
FWE pin
protection
•
Not
Not
Not
When a low level is input to the FWE pin,
1
3
FLMCR1, EBR1, and EBR2 are initialized, and possible* possible* possible
the program/erase-protected state is entered.
Reset/
standby
protection
•
In a reset (including a WDT overflow reset)
and in standby mode, FLMCR1, FLMCR2,
EBR1, and EBR2 are initialized, and the
program/erase-protected state is entered.
•
In a reset via the RES pin, the reset state is
not entered unless the RES pin is held low
until oscillation stabilizes after powering on. In
the case of a reset during operation, hold the
RES pin low for the RES pulse width specified
in the AC Characteristics section.*4
•
When a microcomputer operation error (error Not
possible
generation (FLER = 1)) was detected while
flash memory was being programmed/erased,
error protection is enabled. At this time, the
FLMCR1, EBR1, and EBR2 settings are held,
but programming/erasing is aborted at the time
the error was generated. Error protection is
released only by a reset via the RES pin or a
WDT reset, or in the hardware standby mode.
Error
protection
Program
Not
possible
Erase
Verify
Not
Not
3
possible* possible
Not
Possible*2
3
possible*
Notes: 1. The RAM area that overlapped flash memory is deleted.
Rev. 3.00 Sep 14, 2005 page 633 of 910
REJ09B0258-0300
Section 18 Flash Memory
2. It is possible to perform a program-verify operation on the 128 bytes being
programmed, or an erase-verify operation on the block being erased.
3. All blocks are unerasable and block-by-block specification is not possible.
4. See section 4.2.2, Reset Sequence, and section 18.11, Flash Memory Programming
and Erasing Precautions. The H8/3068F-ZTAT requires a minimum of 20 system clock
cycles for a reset during operation.
18.7.2
Software Protection
Software protection can be implemented by setting the erase block register 1 (EBR1), erase block
register 2 (EBR2), and the RAMS bit in the RAM control register (RAMCR). With software
protection, setting the P or E bit in the flash memory control register 1 (FLMCR1) does not cause
a transition to program mode or erase mode. (See table 18.9.)
Table 18.9 Software Protection
Functions
Item
Description
Block
protection
•
—
Erase protection can be set for individual
blocks by settings in erase block register 1
(EBR1) and erase block register 2
(EBR2)*2. However, programming
protection is disabled.
•
Setting EBR1 and EBR2 to H'00 places all
blocks in the erase-protected state.
•
Setting the RAMS bit 1 in RAMCR places
all blocks in the program/erase-protected
state.
Emulation
protection
Program
Erase
Verify
Not
possible
Possible
Not
Not
Possible
possible*1 possible*3
Notes: 1. The RAM area overlapping flash memory can be written to.
2. When not erasing, set EBR1 and EBR2 to H'00.
3. All blocks are unerasable and block-by-block specification is not possible.
Rev. 3.00 Sep 14, 2005 page 634 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.7.3
Error Protection
In error protection, an error is detected when MCU runaway occurs during flash memory
programming/erasing*1, or operation is not performed in accordance with the program/erase
algorithm, and the program/erase operation is aborted. Aborting the program/erase operation
prevents damage to the flash memory due to overprogramming or overerasing.
If the MCU malfunctions during flash memory programming/erasing, the FLER bit is set to 1 in
the flash memory status register (FLMSR2) and the error protection state is entered. FLMCR1,
FLMCR2, EBR1, and EBR2 settings*3 are retained, but program mode or erase mode is aborted
at the point at which the error occurred. Program mode or erase mode cannot be re-entered by resetting the P or E bit in FLMCR. However, PV and EV bit setting is enabled, and a transition can
be made to verify mode*2.
FLER bit setting conditions are as follows:
1. When flash memory is read during programming/erasing (including a vector read or
instruction fetch)
2. Immediately after the start of exception handling during programming/erasing (excluding
reset, illegal instruction, trap instruction, and division-by-zero exception handling)
3. When a SLEEP instruction (including software standby) is executed during
programming/erasing
4. When the bus is released during programming/erasing
Error protection is released only by a RES pin or WDT reset, or in hardware standby mode.
Notes: 1. State in which the P bit or E bit in FLMCR1 is set to 1. Note that NMI input is
disabled in this state.
2. It is possible to perform a program-verify operation on the 128 bytes being
programmed, or an erase-verify on the block being erased.
3. FLMCR1, EBR1, and EBR2 can be written to. However, the registers are initialized if
a transition is made to software standby mode while in the error protection state.
Figure 18.12 shows the flash memory state transition diagram.
Rev. 3.00 Sep 14, 2005 page 635 of 910
REJ09B0258-0300
Section 18 Flash Memory
Program mode
Erase mode
Reset or standby
(hardware protection)
RES = 0 or STBY = 0
RD VF PR ER INIT FLER = 0
RD VF PR ER FLER = 0
Error occurrence
(software standby)
RES = 0 or
STBY = 0
Error
occurrence
RES = 0 or
STBY = 0
Software
standby mode
Error protection mode
RD VF PR ER FLER = 1
Software standby
mode release
FLMCR1, FLMCR2,
EBR1, EBR2
initialization state
Error protection mode
(software standby)
RD VF PR ER INIT FLER = 1
FLMCR1, EBR1, EBR2
initialization state
RD:
VF:
PR:
ER:
Memory read possible
Verify-read possible
Programming possible
Erasing possible
RD:
VF:
PR:
ER:
INIT:
Memory read not possible
Verify-read not possible
Programming not possible
Erasing not possible
Register initialization state
Figure 18.12 Flash Memory State Transitions
(When High Level is Applied to FWE Pin in Mode 5 or 7 (On-Chip ROM Enabled))
The error protection function is invalid for abnormal operations other than the FLER bit setting
conditions. Also, if a certain time has elapsed before this protection state is entered, damage may
already have been caused to the flash memory. Consequently, this function cannot provide
complete protection against damage to flash memory.
To prevent such abnormal operations, therefore, it is necessary to ensure correct operation in
accordance with the program/erase algorithm, with the flash write enable (FWE) voltage applied,
and to conduct constant monitoring for MCU errors, internally and externally, using the watchdog
timer or other means. There may also be cases where the flash memory is in an erroneous
programming or erroneous erasing state at the point of transition to this protection mode, or
where programming or erasing is not properly carried out because of an abort. In cases such as
these, a forced recovery (program rewrite) must be executed using boot mode. However, it may
also happen that boot mode cannot be normally initiated because of overprogramming or
overerasing.
Rev. 3.00 Sep 14, 2005 page 636 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.8
Flash Memory Emulation in RAM
Making a setting in the RAM control register (RAMCR) enables part of RAM to be overlapped
onto the flash memory area so that data to be written to flash memory can be emulated in RAM in
real time. After the RAMCR setting has been made, accesses can be made from the flash memory
area or the RAM area overlapping flash memory. Emulation can be performed in user mode and
user program mode. Figure 18.13 shows an example of emulation of realtime flash memory
programming.
Start of emulation program
Set RAMCR
Write tuning data to overlap RAM
Execute application program
No
Tuning OK?
Yes
Clear RAMCR
Write to flash memory emulation block
End of emulation program
Figure 18.13 Flowchart of Flash Memory Emulation in RAM
Rev. 3.00 Sep 14, 2005 page 637 of 910
REJ09B0258-0300
Section 18 Flash Memory
This area can be accessed
from both the RAM area
and flash memory area
H'00000
EB0
H'01000
EB1
H'02000
EB2
H'03000
EB3
H'04000
EB4
H'05000
EB5
H'06000
EB6
H'07000
EB7
H'08000
H'FFE000
H'FFEFFF
Flash memory
EB8 to EB13
On-chip RAM
H'FFFF1F
H'5FFFF
Figure 18.14 Example of RAM Overlap Operation
Example of Flash Memory Block Area EB0 Overlapping
1. Set bits RAMS and RAM2 to RAM0 in RAMCR to 1,0, 0, 0, to overlap part of RAM onto the
area (EB0) for which realtime programming is required.
2. Realtime programming is performed using the overlapping RAM.
3. After the program data has been confirmed, the RAMS bit is cleared, releasing RAM overlap.
4. The data written in the overlapping RAM is written into the flash memory space (EB0).
Notes: 1. When the RAMS bit is set to 1, program/erase protection is enabled for all blocks
regardless of the value of RAM2 to RAM0 (emulation protection). In this state, setting
the P or E bit in FLMCR1 will not cause a transition to program mode or erase mode.
When actually programming or erasing a flash memory area, the RAMS bit should be
cleared to 0.
2. A RAM area cannot be erased by execution of software in accordance with the erase
algorithm while flash memory emulation in RAM is being used.
Rev. 3.00 Sep 14, 2005 page 638 of 910
REJ09B0258-0300
Section 18 Flash Memory
3. Block area EB0 contains the vector table. When performing RAM emulation, the
vector table is needed in the overlap RAM.
4. As in on-board programming mode, care is required when applying and releasing FWE
to prevent erroneous programming or erasing. To prevent erroneous programming and
erasing due to program runaway during FWE application, in particular, the watchdog
timer should be set when the PSU, P, ESU, or E bit is set to 1 in FLMCR1, even while
the emulation function is being used.
5. When the emulation function is used, NMI input is prohibited when the P bit or E bit
is set to 1 in FLMCR1, in the same way as with normal programming and erasing.
The P and E bits are cleared by a reset (including a watchdog timer reset), in standby
mode, when a high level is not being input to the FWE pin, or when the SWE bit in
FLMCR1 is 0 while a high level is being input to the FWE pin.
Rev. 3.00 Sep 14, 2005 page 639 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.9
NMI Input Disabling Conditions
All interrupts, including NMI input, should be disabled while flash memory is being programmed
or erased (while the P bit or E bit is set in FLMCR1), and while the boot program is executing in
boot mode*1, to give priority to the program or erase operation. There are three reasons for this:
1. NMI input during programming or erasing might cause a violation of the programming or
erasing algorithm, with the result that normal operation could not be assured.
2. In the NMI exception handling sequence during programming or erasing, the vector would not
be read correctly*2, possibly resulting in MCU runaway.
3. If NMI input occurred during boot program execution, it would not be possible to execute the
normal boot mode sequence.
For these reasons, in on-board programming mode alone there are conditions for disabling NMI
input, as an exception to the general rule. However, this provision does not guarantee normal
erasing and programming or MCU operation. All interrupt requests (exception handling and bus
release), including NMI, must therefore be restricted inside and outside the MCU during FWE
application. NMI input is also disabled in the error protection state and while the P or E bit
remains set in FLMCR1 during flash memory emulation in RAM.
Notes: 1. This is the interval until a branch is made to the boot program area in the on-chip
RAM (This branch takes place immediately after transfer of the user program is
completed). Consequently, after the branch to the RAM area, NMI input is enabled
except during programming and erasing. Interrupt requests must therefore be disabled
inside and outside the MCU until the user program has completed initial programming
(including the vector table and the NMI interrupt handling routine).
2. The vector may not be read correctly in this case for the following two reasons:
• If flash memory is read while being programmed or erased (while the P bit or E bit
is set in FLMCR1), correct read data will not be obtained (undetermined values will
be returned).
• If the entry in the interrupt vector table has not been programmed yet, interrupt
exception handling will not be executed correctly.
Rev. 3.00 Sep 14, 2005 page 640 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.10
Flash Memory PROM Mode
The H8/3068F-ZTAT has a PROM mode as well as the on-board programming modes for
programming and erasing flash memory. In PROM mode, the on-chip ROM can be freely
programmed using a general-purpose PROM writer that supports the Renesas Technology
microcomputer device type with 256-kbyte on-chip flash memory.
18.10.1 Socket Adapters and Memory Map
In PROM mode using a PROM writer, memory reading (verification) and writing and flash
memory initialization (total erasure) can be performed. For these operations, a special socket
adapter is mounted in the PROM writer. The socket adapter product codes are given in table
18.10. In the H8/3068F-ZTAT PROM mode, only the socket adapters shown in this table should
be used.
Table 18.10 H8/3068F-ZTAT Socket Adapter Product Codes
Socket Adapter
Product Code
Product Code
Package
Manufacturer
HD64F3068F
100-pin QFP (FP-100B)
ME3064ESHF1H
HD64F3068TE
100-pin TQFP (TFP-100B)
ME3064ESNF1H
MINATO
ELECTRONICS INC.
HD64F3068F
100-pin QFP (FP-100B)
HF306BQ100D4001
DATA I/O JAPAN CO.
HD64F3068TE
100-pin TQFP (TFP-100B)
HF306BT100D4001
Figure 18.15 shows the memory map in PROM mode.
MCU mode
H'000000
H8/3068F-ZTAT
PROM mode
H'00000
On-chip ROM
H'05FFFF
H'5FFFF
Figure 18.15 Memory Map in PROM Mode
Rev. 3.00 Sep 14, 2005 page 641 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.10.2 Notes on Use of PROM Mode
1. A write to a 128-byte programming unit in PROM mode should be performed once only.
Erasing must be carried out before reprogramming an address that has already been
programmed.
2. When using a PROM writer to reprogram a device on which on-board programming/erasing
has been performed, it is recommended that erasing be carried out before executing
programming.
3. The memory is initially in the erased state when the device is shipped by Renesas Technology.
For samples for which the erasure history is unknown, it is recommended that erasing be
executed to check and correct the initialization (erase) level.
4. The H8/3068F-ZTAT does not support a product identification mode as used with generalpurpose EPROMs, and therefore the device name cannot be set automatically in the PROM
writer.
5. Refer to the instruction manual provided with the socket adapter, or other relevant
documentation, for information on PROM writers and associated program versions that are
compatible with the PROM mode of the H8/3068F-ZTAT.
Rev. 3.00 Sep 14, 2005 page 642 of 910
REJ09B0258-0300
Section 18 Flash Memory
18.11
Flash Memory Programming and Erasing Precautions
Precautions concerning the use of on-board programming mode, the RAM emulation function,
and PROM mode are summarized below.
1. Use the specified voltages and timing for programming and erasing.
Applied voltages in excess of the rating can permanently damage the device. Use a PROM
programmer that supports the Renesas Technology microcomputer device type “F-ZTAT512”
with 512-kbyte on-chip flash memory.
2. Powering on and off (see figures 18.16 to 18.18)
Do not apply a high level to the FWE pin until VCC has stabilized. Also, drive the FWE pin
low before turning off VCC.
When applying or disconnecting VCC power, fix the FWE pin low and place the flash memory
in the hardware protection state.
The power-on and power-off timing requirements should also be satisfied in the event of a
power failure and subsequent recovery. Failure to do so may result in overprogramming or
overerasing due to MCU runaway, and loss of normal memory cell operation.
3. FWE application/disconnection
FWE application should be carried out when MCU operation is in a stable condition. If MCU
operation is not stable, fix the FWE pin low and set the protection state.
The following points must be observed concerning FWE application and disconnection to
prevent unintentional programming or erasing of flash memory:
• Apply FWE when the VCC voltage has stabilized within its rated voltage range.
If FWE is applied when the MCU’s VCC power supply is not within its rated voltage range,
MCU operation will be unstable and flash memory may be erroneously programmed or
erased.
• Apply FWE when oscillation has stabilized (after the elapse of the oscillation settling
time).
When VCC power is turned on, hold the RES pin low for the duration of the oscillation
settling time before applying FWE. Do not apply FWE when oscillation has stopped or is
unstable.
• In boot mode, apply and disconnect FWE during a reset.
In a transition to boot mode, FWE = 1 input and MD2–MD0 setting should be performed
while the RES input is low. FWE and MD2–MD0 pin input must satisfy the mode
programming setup time (tMDS) with respect to the reset release timing. When making a
transition from boot mode to another mode, also, a mode programming setup time is
necessary with respect to the reset release timing.
Rev. 3.00 Sep 14, 2005 page 643 of 910
REJ09B0258-0300
Section 18 Flash Memory
•
•
•
In a reset during operation, the RES pin must be held low for a minimum of 20 system
clock cycles.
In user program mode, FWE can be switched between high and low level regardless of
RES input.
FWE input can also be switched during execution of a program in flash memory.
Do not apply FWE if program runaway has occurred.
During FWE application, the program execution state must be monitored using the
watchdog timer or some other means.
Disconnect FWE only when the SWE, ESU, PSU, EV, PV, E, and P bits in FLMCR1 are
cleared.
Make sure that the SWE, ESU, PSU, EV, PV, E, and P bits are not set by mistake when
applying or disconnecting FWE.
4. Do not apply a constant high level to the FWE pin.
T prevent erroneous programming or erasing due to program runaway, etc., apply a high level
to the FWE pin only when programming or erasing flash memory (including execution of flash
memory emulation using RAM). A system configuration in which a high level is constantly
applied to the FWE pin should be avoided. Also, while a high level is applied to the FWE pin,
the watchdog timer should be activated to prevent overprogramming or overerasing due to
program runaway, etc.
5. Use the recommended algorithm when programming and erasing flash memory.
The recommended algorithm enables programming and erasing to be carried out without
subjecting the device to voltage stress or sacrificing program data reliability. When setting the
PSU or ESU bit in FLMCR1, the watchdog timer should be set beforehand as a precaution
against program runaway, etc.
Also note that access to the flash memory space by means of a MOV instruction, etc., is not
permitted while the P bit or E bit is set.
6. Do not set or clear the SWE bit during execution of a program in flash memory.
Clear the SWE bit before executing a program or reading data in flash memory. When the
SWE bit is set, data in flash memory can be rewritten, but flash memory should only be
accessed for verify operations (verification during programming/erasing).
Similarly, when using the RAM emulation function while a high level is being input to the
FWE pin, the SWE bit must be cleared before executing a program or reading data in flash
memory. However, the RAM area overlapping flash memory space can be read and written to
regardless of whether the SWE bit is set or cleared.
A wait time is necessary after the SWE bit is cleared. For details see table 21.10 in section
21.1.6, Flash Memory Characteristics.
Rev. 3.00 Sep 14, 2005 page 644 of 910
REJ09B0258-0300
Section 18 Flash Memory
7. Do not use interrupts while flash memory is being programmed or erased.
All interrupt requests, including NMI, should be disabled during FWE application to give
priority to program/erase operations (including emulation in RAM).
Bus release must also be disabled.
8. Do not perform additional programming. Erase the memory before reprogramming.
In on-board programming, perform only one programming operation on a 128-byte
programming unit block. Programming should be carried out with the entire programming unit
block erased.
9. Before programming, check that the chip is correctly mounted in the PROM writer.
Overcurrent damage to the device can result if the index marks on the PROM writer socket,
socket adapter, and chip are not correctly aligned.
10. Do not touch the socket adapter or chip during programming.
Touching either of these can cause contact faults and write errors.
11. A wait time of 100 µs or more is necessary when performing a read after a transition to
normal mode from program, erase, or verify mode.
12. Use byte access on the registers that control the flash memory (FLMCR1, FLMCR2,
EBR1, EBR2, and RAMCR).
Rev. 3.00 Sep 14, 2005 page 645 of 910
REJ09B0258-0300
Section 18 Flash Memory
Wait time:
x
Programming/
erasing
possible
Wait time:
y
φ
Min 0 µs
tOSC1
VCC
tMDS
FWE
Min 0 µs
MD2 to MD0*1
tMDS
RES
SWE set
SWE cleared
SWE bit
Period during which flash memory access is prohibited
(x: Wait time after setting SWE bit, y: Wait time after clearing SWE bit)*2
Period during which flash memory can be programmed
(Execution of program in flash memory prohibited, and data reads other than verify operations
prohibited)
Notes: 1. Except when switching modes, the level of the mode pins (MD2–MD0) must be fixed until power-off
by pulling the pins up or down.
2. See section 21.1.6, Flash Memory Characteristics.
Figure 18.16 Power-On/Off Timing (Boot Mode)
Rev. 3.00 Sep 14, 2005 page 646 of 910
REJ09B0258-0300
Section 18 Flash Memory
Wait time:
x
Programming/
erasing
possible
Wait time:
y
φ
Min 0 µs
tOSC1
VCC
FWE
MD2 to MD0*1
tMDS
RES
SWE set
SWE cleared
SWE bit
Period during which flash memory access is prohibited
(x: Wait time after setting SWE bit, y: Wait time after clearing SWE bit)*2
Period during which flash memory can be programmed
(Execution of program in flash memory prohibited, and data reads other than verify operations
prohibited)
Notes: 1. Except when switching modes, the level of the mode pins (MD2–MD0) must be fixed until power-off
by pulling the pins up or down.
2. See section 21.1.6, Flash Memory Characteristics.
Figure 18.17 Power-On/Off Timing (User Program Mode)
Rev. 3.00 Sep 14, 2005 page 647 of 910
REJ09B0258-0300
Programming/
erasing possible
Wait time: x
Wait time: x
Programming/
erasing possible
Wait time: y
Wait time: x
Programming/
erasing possible
Wait time: y
Wait time: y
Wait time: x
Programming/
erasing possible
Section 18 Flash Memory
φ
tOSC1
VCC
Min 0µs
FWE
tMDS
tMDS*2
MD2 to MD0
tMDS
tRESW
RES
SWE
cleared
SWE set
SWE bit
Mode
change*1
Boot
mode
Mode
User
change*1 mode
User program mode
User
mode
User program
mode
Period during which flash memory access is prohibited
(x: Wait time after setting SWE bit, y: Wait time after clearing SWE bit)*3
Period during which flash memory can be programmed
(Execution of program in flash memory prohibited, and data reads other than verify operations prohibited)
Notes: 1. When entering boot mode or making a transition from boot mode to another mode, mode switching must be carried
out by means of RES input. The state of ports with multiplexed address functions and bus control output pins
(CSn, AS, RD, WR) will change during this switchover interval (the interval during which the RES pin input is low),
and therefore these pins should not be used as output signals during this time.
2. When making a transition from boot mode to another mode, the mode programming setup time tMDS must be
satisfied with respect to RES clearance timing.
3. See section 21.1.6, Flash Memory Characteristics.
Figure 18.18 Mode Transition Timing
(Example: Boot Mode → User Mode ↔ User Program Mode)
Rev. 3.00 Sep 14, 2005 page 648 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
Section 19 Clock Pulse Generator
19.1
Overview
The H8/3068F has a built-in clock pulse generator (CPG) that generates the system clock (φ) and
other internal clock signals (φ/2 to φ/4096). After duty adjustment, a frequency divider divides the
clock frequency to generate the system clock (φ). The system clock is output at the φ pin*1 and
furnished as a master clock to prescalers that supply clock signals to the on-chip supporting
modules. Frequency division ratios of 1/1, 1/2, 1/4, and 1/8 can be selected for the frequency
divider by settings in a division control register (DIVCR)*2. Power consumption in the chip is
reduced in almost direct proportion to the frequency division ratio.
Notes: 1. Usage of the φ pin differs depending on the chip operating mode and the PSTOP bit
setting in the module standby control register (MSTCR). For details, see section 20.7,
System Clock Output Disabling Function.
2. The division ratio of the frequency divider can be changed dynamically during
operation. The clock output at the φ pin also changes when the division ratio is
changed. The frequency output at the φ pin is shown below.
φ = EXTAL × n
where, EXTAL: Frequency of crystal resonator or external clock signal
n:
Frequency division ratio (n = 1/1, 1/2, 1/4, or 1/8)
Rev. 3.00 Sep 14, 2005 page 649 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
19.1.1
Block Diagram
Figure 19.1 shows a block diagram of the clock pulse generator.
CPG
XTAL
Oscillator
EXTAL
Duty
adjustment
circuit
Frequency
divider
φ
Prescalers
Division
control
register
Data bus
φ pin
φ/2 to φ/4096
Figure 19.1 Block Diagram of Clock Pulse Generator
Rev. 3.00 Sep 14, 2005 page 650 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
19.2
Oscillator Circuit
Clock pulses can be supplied by connecting a crystal resonator, or by input of an external clock
signal.
19.2.1
Connecting a Crystal Resonator
Circuit Configuration: A crystal resonator can be connected as in the example in figure 19.2.
Damping resistance Rd should be selected according to table 19.1 (1), and external capacitances
CL1 and CL2 according to table 19.1 (2). An AT-cut parallel-resonance crystal should be used.
CL1
EXTAL
XTAL
Rd
CL2
Figure 19.2 Connection of Crystal Resonator (Example)
If a crystal resonator with a frequency higher than 20 MHz is connected, the external load
capacitance values in table 19.1 (2) should not exceed 10 [pF]. Also, in order to improve the
accuracy of the oscillation frequency, a thorough study of oscillation matching evaluation, etc.,
should be carried out when deciding the circuit constants.
Table 19.1 (1)
Damping Resistance Value
Damping
Resistance
Value
2
2 < f ≤ 4 4 < f ≤8 8 < f ≤ 10 10 < f ≤ 13 13 < f ≤ 16 16 < f ≤ 18 18 < f ≤ 25
Rd (Ω)
500
1k
Frequency f (MHz)
200
0
0
0
0
0
Note: A crystal resonator between 2 MHz and 25 MHz can be used. If the chip is to be operated
at less than 2 MHz, the on-chip frequency divider should be used. (A crystal resonator of
less than 2 MHz cannot be used.)
Rev. 3.00 Sep 14, 2005 page 651 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
Table 19.1 (2)
External Capacitance Values
External Capacitance Value
5 V Version
Frequency f (MHz)
20 < f ≤ 25
2 ≤ f ≤ 20
CL1 = CL2 (pF)
10
10 to 22
Crystal Resonator: Figure 19.3 shows an equivalent circuit of the crystal resonator. The crystal
resonator should have the characteristics listed in table 19.2.
CL
L
Rs
XTAL
EXTAL
AT-cut parallel-resonance type
C0
Figure 19.3 Crystal Resonator Equivalent Circuit
Table 19.2 Crystal Resonator Parameters
Frequency (MHz)
2
4
8
10
12
16
18
20
25
Rs max (Ω)
500
120
80
70
60
50
40
40
40
Co (pF)
7 pF
max
7 pF
max
7 pF
max
7 pF
max
7 pF
max
7 pF
max
7 pF
max
7 pF
max
7 pF
max
Use a crystal resonator with a frequency equal to the system clock frequency (φ).
Notes on Board Design: When a crystal resonator is connected, the following points should be
noted:
Other signal lines should be routed away from the oscillator circuit to prevent induction from
interfering with correct oscillation. See figure 19.4.
When the board is designed, the crystal resonator and its load capacitors should be placed as close
as possible to the XTAL and EXTAL pins.
Rev. 3.00 Sep 14, 2005 page 652 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
Avoid
C
Signal A
Signal B
H8/3068F chip
L2
XTAL
EXTAL
C
L1
Figure 19.4 Oscillator Circuit Block Board Design Precautions
19.2.2
External Clock Input
Circuit Configuration: An external clock signal can be input as shown in the examples in figure
19.5. If the XTAL pin is left open, the stray capacitance should not exceed 10 pF. If the stray
capacitance at the XTAL pin exceeds 10 pF in configuration a, use the connection shown in
configuration b instead, and hold the external clock high in standby mode.
External clock input
EXTAL
XTAL
Open
a. XTAL pin left open
External clock input
EXTAL
XTAL
b. Complementary clock input at XTAL pin
Figure 19.5 External Clock Input (Examples)
Rev. 3.00 Sep 14, 2005 page 653 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
External Clock: The external clock frequency should be equal to the system clock frequency
when not divided by the on-chip frequency divider. Table 19.3 shows the clock timing, figure 19.6
shows the external clock input timing, and figure 19.7 shows the external clock output settling
delay timing. When the appropriate external clock is input via the EXTAL pin, its waveform is
corrected by the on-chip oscillator and duty adjustment circuit.
When the appropriate external clock is input via the EXTAL pin, its waveform is corrected by the
on-chip oscillator and duty adjustment circuit. The resulting stable clock is output to external
devices after the external clock settling time (tDEXT) has passed after the clock input. The system
must remain reset with the reset signal low during tDEXT, while the clock output is unstable.
Table 19.3 Clock Timing
VCC = 5.0 V ± 10%
Item
Symbol
Min
Max
Unit
Test Conditions
External clock input low
pulse width
tEXL
15
—
ns
Figure 19.6
External clock input high
pulse width
tEXH
15
—
ns
External clock rise time
tEXr
—
5
ns
External clock fall time
tEXf
—
5
ns
Clock low pulse width
tCL
0.4
0.6
tcyc
φ ≥ 5 MHz
80
—
ns
φ < 5 MHz
0.4
0.6
tcyc
φ ≥ 5 MHz
80
—
ns
φ < 5 MHz
500
—
µs
Figure 19.7
Clock high pulse width
tCH
External clock output
settling delay time
tDEXT*
Figure 19.17
Note: * tDEXT includes a RES pulse width (tRESW ). tRESW = 20 tcyc
tEXH
tEXL
VCC × 0.7
EXTAL
VCC × 0.5
0.3 V
tEXr
tEXf
Figure 19.6 External Clock Input Timing
Rev. 3.00 Sep 14, 2005 page 654 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
VCC
STBY
VIH
EXTAL
φ (internal or
external)
RES
tDEXT
Figure 19.7 External Clock Output Settling Delay Timing
19.3
Duty Adjustment Circuit
When the oscillator frequency is 5 MHz or higher, the duty adjustment circuit adjusts the duty
cycle of the clock signal from the oscillator to generate φ.
19.4
Prescalers
The prescalers divide the system clock (φ) to generate internal clocks (φ/2 to φ/4096).
Rev. 3.00 Sep 14, 2005 page 655 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
19.5
Frequency Divider
The frequency divider divides the duty-adjusted clock signal to generate the system clock (φ). The
frequency division ratio can be changed dynamically by modifying the value in DIVCR, as
described below. Power consumption in the chip is reduced in almost direct proportion to the
frequency division ratio. The system clock generated by the frequency divider can be output at the
φ pin.
19.5.1
Register Configuration
Table 19.4 summarizes the frequency division register.
Table 19.4 Frequency Division Register
Address*
Name
Abbreviation
R/W
Initial Value
H'EE01B
Division control register
DIVCR
R/W
H'FC
Note: * Lower 20 bits of the address in advanced mode.
19.5.2
Division Control Register (DIVCR)
DIVCR is an 8-bit readable/writable register that selects the division ratio of the frequency
divider.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
DIV1
DIV0
Initial value
1
1
1
1
1
1
0
0
Read/Write
—
—
—
—
—
—
R/W
R/W
Reserved bits
Divide bits 1 and 0
These bits select the
frequency division ratio
DIVCR is initialized to H'FC by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 2—Reserved: These bits cannot be modified and are always read as 1.
Rev. 3.00 Sep 14, 2005 page 656 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
Bits 1 and 0—Divide (DIV1, DIV0): These bits select the frequency division ratio, as follows.
Bit 1
DIV1
Bit 0
DIV0
Frequency Division Ratio
0
0
1/1
0
1
1/2
1
0
1/4
1
1
1/8
19.5.3
Usage Notes
(Initial value)
The DIVCR setting changes the φ frequency, so note the following points.
• Select a frequency division ratio that stays within the assured operation range specified for the
clock cycle time tcyc in the AC electrical characteristics. Note that ømin = lower limit of the
operating frequency range. Ensure that ø is not below this lower limit.
• All on-chip module operations are based on φ. Note that the timing of timer operations, serial
communication, and other time-dependent processing differs before and after any change in
the division ratio. The waiting time for exit from software standby mode also changes when
the division ratio is changed. For details, see section 20.4.3, Selection of Waiting Time for
Exit from Software Standby Mode.
Rev. 3.00 Sep 14, 2005 page 657 of 910
REJ09B0258-0300
Section 19 Clock Pulse Generator
Rev. 3.00 Sep 14, 2005 page 658 of 910
REJ09B0258-0300
Section 20 Power-Down State
Section 20 Power-Down State
20.1
Overview
The H8/3068F has a power-down state that greatly reduces power consumption by halting the
CPU, and a module standby function that reduces power consumption by selectively halting onchip modules.
The power-down state includes the following three modes:
• Sleep mode
• Software standby mode
• Hardware standby mode
The module standby function can halt on-chip supporting modules independently of the powerdown state. The modules that can be halted are the 16-bit timer, 8-bit timer, SCI0, SCI1, SCI2,
DMAC, DRAM interface, and A/D converter.
Table 20.1 indicates the methods of entering and exiting the power-down modes and module
standby mode, and gives the status of the CPU and on-chip supporting modules in each mode.
Rev. 3.00 Sep 14, 2005 page 659 of 910
REJ09B0258-0300
tion executed
mode
Rev. 3.00 Sep 14, 2005 page 660 of 910
REJ09B0258-0300
bit set to 1 in
Halted
—
mined
reset
and
Halted
reset
Undeter- and
*2
*2
*2
reset
held*1
reset
reset
and
reset
held*1
reset
and
Halted
and
and
Halted
Halted
Halted
and
Halted
reset
and
Halted
and
and
reset
Halted
Halted
Active
and
Halted
Active
Timer
Active
8-Bit
16-Bit
Interface Timer
DRAM
*2
reset
and
Halted
reset
and
Halted
reset
and
Halted
Active
SCI0
*2
reset
and
Halted
reset
and
Halted
reset
and
Halted
Active
SCI1
*2
reset
and
Halted
reset
and
Halted
reset
and
Halted
Active
SCI2
*2
reset
and
Halted
reset
and
Halted
reset
and
Halted
Active
A/D
*2
—
Held
Held
Held
*3
impedance*2
High
impedance
High
output
High
φ output
Module Standby Control Register L (MSTCRL).
• STBY
• STBY
• RES
• IRQ0 to IRQ2
• NMI
• STBY
• RES
• Interrupt
Conditions
Exiting
—
bit to 0*5
• Clear MSTCR
• RES
• STBY
impedance • RES
High
Held
Held
Ports
I/O
Software standby bit
MSTCRL: Module standby control register L
MSTCRH: Module standby control register H
System control register
SSBY:
0, then set up the module registers again.
5. When a MSTCR bit is set to 1, the registers of the corresponding on-chip supporting module are initialized. To restart the module, first clear the MSTCR bit to
4. When P67 is used as the φ output pin.
3. The RAME bit must be cleared to 0 in SYSCR before the transition from the program execution state to hardware standby mode.
SYSCR:
Legend
Active
reset
and
Halted
reset
and
Halted
Active
*4
φ clock
Modules RAM output
Other
2. State in which the corresponding MSTCR bit was set to 1. For details see section 20.2.2, Module Standby Control Register H (MSTCRH) and section 20.2.3,
Notes: 1. RTCNT and bits 7 and 6 of RTMCSR are initialized. Other bits and registers hold their previous states.
MSTCR
Corresponding Active Active
standby
STBY pin
Module
mode
standby
Hardware Low input at
Halted Halted
while SSBY = 1
mode
in SYSCR
and
reset
Halted
tion executed
Active
standby
Held
Held
s
Register DMAC
CPU
Software SLEEP instruc- Halted Halted
in SYSCR
while SSBY = 0
SLEEP instruc- Active Halted
Sleep
Clock CPU
Conditions
Entering
Mode
State
Section 20 Power-Down State
Table 20.1 Power-Down State and Module Standby Function
Section 20 Power-Down State
20.2
Register Configuration
The H8/3068F has a system control register (SYSCR) that controls the power-down state, and
module standby control registers H (MSTCRH) and L (MSTCRL) that control the module
standby function. Table 20.2 summarizes these registers.
Table 20.2 Control Register
Address*
Name
Abbreviation
R/W
Initial Value
H'EE012
System control register
SYSCR
R/W
H'09
H'EE01C
Module standby control register H
MSTCRH
R/W
H'78
H'EE01D
Module standby control register L
MSTCRL
R/W
H'00
Note: * Lower 20 bits of the address in advanced mode.
20.2.1
System Control Register (SYSCR)
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
Initial value
0
0
0
0
1
0
0
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RAM enable
Software standby
output port enable
NMI edge select
User bit enable
Standby timer select 2 to 0
These bits select the
waiting time of the CPU
and peripheral functions
Software standby
Enables transition to
software standby mode
SYSCR is an 8-bit readable/writable register. Bit 7 (SSBY), bits 6 to 4 (STS2 to STS0), and bit 1
(SSOE) control the power-down state. For information on the other SYSCR bits, see section 3.3,
System Control Register (SYSCR).
Rev. 3.00 Sep 14, 2005 page 661 of 910
REJ09B0258-0300
Section 20 Power-Down State
Bit 7—Software Standby (SSBY): Enables transition to software standby mode. When software
standby mode is exited by an external interrupt, this bit remains set to 1 after the return to normal
operation. To clear this bit, write 0.
Bit 7
SSBY
Description
0
SLEEP instruction causes transition to sleep mode
1
SLEEP instruction causes transition to software standby mode
(Initial value)
Bits 6 to 4—Standby Timer Select (STS2 to STS0): These bits select the length of time the
CPU and on-chip supporting modules wait for the clock to settle when software standby mode is
exited by an external interrupt. If the clock is generated by a crystal resonator, set these bits
according to the clock frequency so that the waiting time will be at least 7 ms (oscillation settling
time). See table 20.3. If an external clock is used, set these bits so that the waiting time will be at
least 100 µs.
Bit 6
STS2
Bit 5
STS1
Bit 4
STS0
Description
0
0
0
Waiting time = 8,192 states
1
Waiting time = 16,384 states
0
Waiting time = 32,768 states
1
Waiting time = 65,536 states
1
1
0
1
0
Waiting time = 131,072 states
1
Waiting time = 262,144 states
0
Waiting time = 1,024 states
1
Illegal setting
(Initial value)
Bit 1—Software Standby Output Port Enable (SSOE): Specifies whether the address bus and
bus control signals (CS0 to CS7, AS, RD, HWR, LWR, UCAS, LCAS, and RFSH) are kept as
outputs or fixed high, or placed in the high-impedance state in software standby mode.
Bit 1
SSOE
Description
0
In software standby mode, the address bus and bus control signals
are all high-impedance
1
In software standby mode, the address bus retains its output state
and bus control signals are fixed high
Rev. 3.00 Sep 14, 2005 page 662 of 910
REJ09B0258-0300
(Initial value)
Section 20 Power-Down State
20.2.2
Module Standby Control Register H (MSTCRH)
MSTCRH is an 8-bit readable/writable register that controls output of the system clock (φ). It also
controls the module standby function, which places individual on-chip supporting modules in the
standby state. Module standby can be designated for the SCI0, SCI1, SCI2.
Bit
7
6
5
4
3
2
1
0
MSTPH2 MSTPH1 MSTPH0
PSTOP
—
—
—
—
Initial value
0
1
1
1
1
0
0
0
Read/Write
R/W
—
—
—
—
R/W
R/W
R/W
Reserved bit
Module standby H2 to 0
These bits select modules
to be placed in standby
φ clock stop
Enables or disables
output of the system clock
MSTCRH is initialized to H'78 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bit 7—φ
φ Clock Stop (PSTOP): Enables or disables output of the system clock (φ).
Bit 1
PSTOP
Description
0
System clock output is enabled
1
System clock output is disabled
(Initial value)
Bits 6 to 3—Reserved: These bits cannot be modified and are always read as 1.
Bit 2—Module Standby H2 (MSTPH2): Selects whether to place the SCI2 in standby.
Bit 2
MSTPH2
Description
0
SCI2 operates normally
1
SCI2 is in standby state
(Initial value)
Rev. 3.00 Sep 14, 2005 page 663 of 910
REJ09B0258-0300
Section 20 Power-Down State
Bit 1—Module Standby H1 (MSTPH1): Selects whether to place the SCI1 in standby.
Bit 1
MSTPH1
Description
0
SCI1 operates normally
1
SCI1 is in standby state
(Initial
value)
Bit 0—Module Standby H0 (MSTPH0): Selects whether to place the SCI0 in standby.
Bit 0
MSTPH0
Description
0
SCI0 operates normally
1
SCI0 is in standby state
20.2.3
(Initial
value)
Module Standby Control Register L (MSTCRL)
MSTCRL is an 8-bit readable/writable register that controls the module standby function, which
places individual on-chip supporting modules in the standby state. Module standby can be
designated for the DMAC, 16-bit timer, DRAM interface, 8-bit timer, and A/D converter
modules.
Bit
7
6
MSTPL7
—
Initial value
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
5
4
3
2
1
0
—
MSTPL0
0
0
0
R/W
R/W
R/W
MSTPL5 MSTPL4 MSTPL3 MSTPL2
Module standby L7, L5 to L2, L0
These bits select modules to be
placed in standby
Reserved bits
MSTCRL is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Rev. 3.00 Sep 14, 2005 page 664 of 910
REJ09B0258-0300
Section 20 Power-Down State
Bit 7—Module Standby L7 (MSTPL7): Selects whether to place the DMAC in standby.
Bit 7
MSTPL7
Description
0
DMAC operates normally
1
DMAC is in standby state
(Initial value)
Bit 6—Reserved: This bit can be written and read.
Bit 5—Module Standby L5 (MSTPL5): Selects whether to place the DRAM interface in
standby.
Bit 5
MSTPL5
Description
0
DRAM interface operates normally
1
DRAM interface is in standby state
(Initial value)
Bit 4—Module Standby L4 (MSTPL4): Selects whether to place the 16-bit timer in standby.
Bit 4
MSTPL4
Description
0
16-bit timer operates normally
1
16-bit timer is in standby state
(Initial value)
Bit 3—Module Standby L3 (MSTPL3): Selects whether to place 8-bit timer channels 0 and 1 in
standby.
Bit 3
MSTPL3
Description
0
8-bit timer channels 0 and 1 operate normally
1
8-bit timer channels 0 and 1 are in standby state
(Initial value)
Rev. 3.00 Sep 14, 2005 page 665 of 910
REJ09B0258-0300
Section 20 Power-Down State
Bit 2—Module Standby L2 (MSTPL2): Selects whether to place 8-bit timer channels 2 and 3 in
standby.
Bit 2
MSTPL2
Description
0
8-bit timer channels 2 and 3 operate normally
1
8-bit timer channels 2 and 3 are in standby state
(Initial value)
Bit 1—Reserved: This bit can be written and read.
Bit 0—Module Standby L0 (MSTPL0): Selects whether to place the A/D converter in standby.
Bit 0
MSTPL0
Description
0
A/D converter operates normally
1
A/D converter is in standby state
Rev. 3.00 Sep 14, 2005 page 666 of 910
REJ09B0258-0300
(Initial value)
Section 20 Power-Down State
20.3
Sleep Mode
20.3.1
Transition to Sleep Mode
When the SSBY bit is cleared to 0 in SYSCR, execution of the SLEEP instruction causes a
transition from the program execution state to sleep mode. Immediately after executing the
SLEEP instruction the CPU halts, but the contents of its internal registers are retained. The DMA
controller (DMAC), DRAM interface, and on-chip supporting modules do not halt in sleep mode.
Modules which have been placed in standby by the module standby function, however, remain
halted.
20.3.2
Exit from Sleep Mode
Sleep mode is exited by an interrupt, or by input at the RES or STBY pin.
Exit by Interrupt: An interrupt terminates sleep mode and causes a transition to the interrupt
exception handling state. Sleep mode is not exited by an interrupt source in an on-chip supporting
module if the interrupt is disabled in the on-chip supporting module. Sleep mode is not exited by
an interrupt other than NMI if the interrupt is masked by interrupt priority settings and the
settings of the I and UI bits in CCR, IPR.
Exit by RES Input: Low input at the RES pin exits from sleep mode to the reset state.
Exit by STBY Input: Low input at the STBY pin exits from sleep mode to hardware standby
mode.
Rev. 3.00 Sep 14, 2005 page 667 of 910
REJ09B0258-0300
Section 20 Power-Down State
20.4
Software Standby Mode
20.4.1
Transition to Software Standby Mode
To enter software standby mode, execute the SLEEP instruction while the SSBY bit is set to 1 in
SYSCR.
In software standby mode, current dissipation is reduced to an extremely low level because the
CPU, clock, and on-chip supporting modules all halt. The DMAC and on-chip supporting
modules are reset and halted. As long as the specified voltage is supplied, however, CPU register
contents and on-chip RAM data are retained. The settings of the I/O ports and DRAM interface*
are also held. When the WDT is used as a watchdog timer (WT/IT = 1), the TME bit must be
cleared to 0 before setting SSBY. Also, when setting TME to 1, SSBY should be cleared to 0.
Clear the BRLE bit in BRCR (inhibiting bus release) before making a transition to software
standby mode.
Note: * RTCNT and bits 7 and 6 of RTMCSR are initialized. Other bits and registers hold their
previous states.
20.4.2
Exit from Software Standby Mode
Software standby mode can be exited by input of an external interrupt at the NMI, IRQ0, IRQ1, or
IRQ2 pin, or by input at the RES or STBY pin.
Exit by Interrupt: When an NMI, IRQ0, IRQ1, or IRQ2 interrupt request signal is received, the
clock oscillator begins operating. After the oscillator settling time selected by bits STS2 to STS0
in SYSCR, stable clock signals are supplied to the entire chip, software standby mode ends, and
interrupt exception handling begins. Software standby mode is not exited if the interrupt enable
bits of interrupts IRQ0, IRQ1, and IRQ2 are cleared to 0, or if these interrupts are masked in the
CPU.
Exit by RES Input: When the RES input goes low, the clock oscillator starts and clock pulses are
supplied immediately to the entire chip. The RES signal must be held low long enough for the
clock oscillator to stabilize. When RES goes high, the CPU starts reset exception handling.
Exit by STBY Input: Low input at the STBY pin causes a transition to hardware standby mode.
Rev. 3.00 Sep 14, 2005 page 668 of 910
REJ09B0258-0300
Section 20 Power-Down State
20.4.3
Selection of Waiting Time for Exit from Software Standby Mode
Bits STS2 to STS0 in SYSCR and bits DIV1 and DIV0 in DIVCR should be set as follows.
Crystal Resonator: Set STS2 to STS0, DIV1, and DIV0 so that the waiting time (for the clock to
stabilize) is at least 7 ms. Table 20.3 indicates the waiting times that are selected by STS2 to
STS0, DIV1, and DIV0 settings at various system clock frequencies.
External Clock: Set STS2 to STS0, DIV1, and DIV0 so that the waiting time is at least 100 µs.
Table 20.3 Clock Frequency and Waiting Time for Clock to Settle
DIV1 DIV0 STS2 STS1 STS0 Waiting Time 25 MHz 20 MHz 18 MHz 16 MHz 12 MHz 10 MHz 8 MHz
6 MHz
4 MHz
2 MHz
1 MHz
Unit
0
1.0
1.3
2.0
4.1
8.2*
ms
0
1
1
0
1
0
1
0
0
0
8192 states
0.3
0.4
0.46
0
0
1
16384 states
0.7
0.8
0.91
1.0
1.3
1.6
2.0
2.7
4.1
8.2*
16.4
0
1
0
32768 states
1.3
1.6
1.8
2.0
2.7
3.3
4.1
5.5
8.2*
16.4
32.8
0
1
1
65536 states
2.6
3.3
3.6
4.1
5.5
6.6
8.2*
10.9*
16.4
32.8
65.5
1
0
0
131072 states 5.2
6.6
7.3*
8.2*
10.9*
13.1*
16.4
21.8
32.8
65.5
131.1
1
0
1
262144 states 10.5*
13.1*
14.6
16.4
21.8
26.2
32.8
43.7
65.5
131.1
262.1
1
1
0
1024 states
0.05
0.057
0.064
0.085
0.10
0.13
0.17
0.26
0.51
1.0
1
1
1
0.04
0.51
0.65
0.8
Illegal setting
0
0
0
8192 states
0.7
0.8
0.91
1.02
1.4
1.6
2.0
2.7
4.1
8.2*
16.4*
0
0
1
16384 states
1.3
1.6
1.8
2.0
2.7
3.3
4.1
5.5
8.2*
16.4
32.8
0
1
0
32768 states
2.6
3.3
3.6
4.1
5.5
6.6
8.2*
10.9*
16.4
32.8
65.5
0
1
1
65536 states
5.2
6.6
7.3*
8.2*
10.9*
13.1*
16.4
21.8
32.8
65.5
131.1
1
0
0
131072 states 10.5*
13.1*
14.6
16.4
21.8
26.2
32.8
43.7
65.5
131.1
262.1
1
0
1
262144 states 21.0
26.2
29.1
32.8
43.7
52.4
65.5
87.4
131.1
262.1
524.3
1
1
0
1024 states
0.10
0.11
0.13
0.17
0.20
0.26
0.34
0.51
1.0
2.0
1
1
1
0.08
Illegal setting
0
0
0
8192 states
1.3
1.6
1.8
2.0
2.7
3.3
4.1
5.5
8.2*
16.4*
32.8*
0
0
1
16384 states
2.6
3.3
3.6
4.1
5.5
6.6
8.2*
10.9*
16.4
32.8
65.5
0
1
0
32768 states
5.2
6.6
7.3*
8.2*
10.9*
13.1*
16.4
21.8
32.8
65.5
131.1
0
1
1
65536 states
10.5*
13.1*
14.6
16.4
21.8
26.2
32.8
43.7
65.5
131.1
262.1
1
0
0
131072 states 21.0
26.2
29.1
32.8
43.7
52.4
65.5
87.4
131.1
262.1
524.3
1
0
1
262144 states 41.9
52.4
58.3
65.5
87.4
104.9
131.1
174.8
262.1
524.3
1048.6
1
1
0
1024 states
0.20
0.23
0.26
0.34
0.41
0.51
0.68
1.02
2.0
4.1
1
1
1
0.16
0
0
0
8192 states
2.6
3.3
3.6
4.1
5.5
6.6
8.2*
10.9*
16.4*
32.8*
65.5
0
1
16384 states
5.2
6.6
7.3*
8.2*
10.9*
13.1*
16.4
21.8
32.8
65.5
131.1
0
1
0
32768 states
10.5
13.1*
14.6
16.4
21.8
26.2
32.8
43.7
65.5
131.1
262.1
0
1
1
65536 states
21.0*
26.2
29.1
32.8
43.7
52.4
65.5
87.4
131.1
262.1
524.3
1
0
0
131072 states 41.9
52.4
58.3
65.5
87.4
104.9
131.1
174.8
262.1
524.3
1048.6
1
0
1
262144 states 83.9
104.9
116.5
131.1
174.8
209.7
262.1
349.5
524.3
1048.6 2097.1
1024 states
0.41
0.46
0.51
0.68
0.82
1.0
1.4
2.0
4.1
1
0
1
1
1
ms
Illegal setting
0
1
ms
0.33
ms
8.2*
Illegal setting
* : Recommended setting
Rev. 3.00 Sep 14, 2005 page 669 of 910
REJ09B0258-0300
Section 20 Power-Down State
20.4.4
Sample Application of Software Standby Mode
Figure 20.1 shows an example in which software standby mode is entered at the fall of NMI and
exited at the rise of NMI.
With the NMI edge select bit (NMIEG) cleared to 0 in SYSCR (selecting the falling edge), an
NMI interrupt occurs. Next the NMIEG bit is set to 1 (selecting the rising edge) and the SSBY bit
is set to 1; then the SLEEP instruction is executed to enter software standby mode.
Software standby mode is exited at the next rising edge of the NMI signal.
Clock
oscillator
φ
NMI
NMIEG
SSBY
NMI interrupt
handler
NMIEG = 1
SSBY = 1
Software standby
mode (powerdown state)
Oscillator
settling time
(tosc2)
NMI exception
handling
SLEEP
instruction
Figure 20.1 NMI Timing for Software Standby Mode (Example)
20.4.5
Note
The I/O ports retain their existing states in software standby mode. If a port is in the high output
state, its output current is not reduced.
Rev. 3.00 Sep 14, 2005 page 670 of 910
REJ09B0258-0300
Section 20 Power-Down State
20.5
Hardware Standby Mode
20.5.1
Transition to Hardware Standby Mode
Regardless of its current state, the chip enters hardware standby mode whenever the STBY pin
goes low. Hardware standby mode reduces power consumption drastically by halting all functions
of the CPU, DMAC, DRAM interface, and on-chip supporting modules. All modules are reset
except the on-chip RAM. As long as the specified voltage is supplied, on-chip RAM data is
retained. I/O ports are placed in the high-impedance state.
Clear the RAME bit to 0 in SYSCR before STBY goes low to retain on-chip RAM data.
The inputs at the mode pins (MD2 to MD0) should not be changed during hardware standby
mode.
20.5.2
Exit from Hardware Standby Mode
Hardware standby mode is exited by inputs at the STBY and RES pins. While RES is low, when
STBY goes high, the clock oscillator starts running. RES should be held low long enough for the
clock oscillator to settle. When RES goes high, reset exception handling begins, followed by a
transition to the program execution state.
20.5.3
Timing for Hardware Standby Mode
Figure 20.2 shows the timing relationships for hardware standby mode. To enter hardware
standby mode, first drive RES low, then drive STBY low. To exit hardware standby mode, first
drive STBY high, wait for the clock to settle, then bring RES from low to high.
Rev. 3.00 Sep 14, 2005 page 671 of 910
REJ09B0258-0300
Section 20 Power-Down State
Clock
oscillator
RES
STBY
Oscillator
settling time
Reset
exception
handling
Figure 20.2 Hardware Standby Mode Timing
Rev. 3.00 Sep 14, 2005 page 672 of 910
REJ09B0258-0300
Section 20 Power-Down State
20.6
Module Standby Function
20.6.1
Module Standby Timing
The module standby function can halt several of the on-chip supporting modules (SCI2, SCI1,
SCI0, the DMAC, 16-bit timer, 8-bit timer, DRAM interface, and A/D converter) independently
in the power-down state. This standby function is controlled by bits MSTPH2 to MSTPH0 in
MSTCRH and bits MSTPL7 to MSTPL0 in MSTCRL. When one of these bits is set to 1, the
corresponding on-chip supporting module is placed in standby and halts at the beginning of the
next bus cycle after the MSTCR write cycle.
20.6.2
Read/Write in Module Standby
When an on-chip supporting module is in module standby, read/write access to its registers is
disabled. Read access always results in H'FF data. Write access is ignored.
20.6.3
Usage Notes
When using the module standby function, note the following points.
DMAC: When setting a bit in MSTCR to 1 to place the DMAC in module standby, make sure
that the DMAC is not currently requesting the bus right. If the corresponding bit in MSTCR is set
to 1 when a bus request is present, operation of the bus arbiter becomes ambiguous and a
malfunction may occur.
DRAM Interface: When the module standby function is used on the DRAM interface, set the
MSTCR bit to 1 while DRAM space is deselected.
On-Chip Supporting Module Interrupts: Before setting a module standby bit, first disable
interrupts by that module. When an on-chip supporting module is placed in standby by the module
standby function, its registers are initialized, including registers with interrupt request flags.
Pin States: Pins used by an on-chip supporting module lose their module functions when the
module is placed in module standby. What happens after that depends on the particular pin. For
details, see section 8, I/O Ports. Pins that change from the input to the output state require special
care. For example, if SCI1 is placed in module standby, the receive data pin loses its receive data
function and becomes a port pin. If its port DDR bit is set to 1, the pin becomes a data output pin,
and its output may collide with external SCI transmit data. Data collision should be prevented by
clearing the port DDR bit to 0 or taking other appropriate action.
Register Resetting: When an on-chip supporting module is halted by the module standby
function, all its registers are initialized. To restart the module, after its MSTCR bit is cleared to 0,
Rev. 3.00 Sep 14, 2005 page 673 of 910
REJ09B0258-0300
Section 20 Power-Down State
its registers must be set up again. It is not possible to write to the registers while the MSTCR bit
is set to 1.
MSTCR Access from DMAC Disabled: To prevent malfunctions, MSTCR can only be
accessed from the CPU. It can be read by the DMAC, but it cannot be written by the DMAC.
20.7
System Clock Output Disabling Function
Output of the system clock (φ) can be controlled by the PSTOP bit in MSTCRH. When the
PSTOP bit is set to 1, output of the system clock halts and the φ pin is placed in the highimpedance state. Figure 20.3 shows the timing of the stopping and starting of system clock
output. When the PSTOP bit is cleared to 0, output of the system clock is enabled. Table 20.4
indicates the state of the φ pin in various operating states.
MSTCRH write cycle
MSTCRH write cycle
(PSTOP = 1)
(PSTOP = 0)
T1
T2
T3
T1
T2
T3
φ pin
High impedance
Figure 20.3 Starting and Stopping of System Clock Output
Table 20.4 φ Pin State in Various Operating States
Operating State
PSTOP = 0
PSTOP = 1
Hardware standby
High impedance
High impedance
Software standby
Always high
High impedance
Sleep mode
System clock output
High impedance
Normal operation
System clock output
High impedance
Rev. 3.00 Sep 14, 2005 page 674 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Section 21 Electrical Characteristics
21.1
Electrical Characteristics of H8/3068F-ZTAT
21.1.1
Absolute Maximum Ratings
Table 21.1 lists the absolute maximum ratings.
Table 21.1 Absolute Maximum Ratings
Item
Symbol
Value
Unit
VCC*
–0.3 to +7.0
V
Vin
–0.3 to VCC +0.3
V
Input voltage (except for port 7)*
Vin
–0.3 to VCC +0.3
V
Input voltage (port 7)
Vin
–0.3 to AVCC +0.3
V
Reference voltage
VREF
–0.3 to AVCC +0.3
V
Analog power supply voltage
AVCC
–0.3 to +7.0
V
Analog input voltage
VAN
–0.3 to AVCC +0.3
V
1
Power supply voltage
Input voltage (FWE)*
2
2
3
Operating temperature
Topr
–20 to +75*
°C
Storage temperature
Tstg
–55 to +125
°C
Caution: Permanent damage to the chip may result if absolute maximum ratings are exceeded.
Notes: 1. Do not apply the power supply voltage to the VCL pin. Connect an external capacitor
between this pin and GND.
2. 12 V must not be applied to any pin, as this may cause permanent damage to the
device.
3. The operating temperature range for flash memory programming/erasing is 0°C to
+75°C.
Rev. 3.00 Sep 14, 2005 page 675 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.1.2
DC Characteristics
Table 21.2 lists the DC characteristics. Table 21.3 lists the permissible output currents.
Table 21.2 DC Characteristics (1)
Conditions: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC*1,
VSS = AVSS = 0 V*1, Ta = –20°C to +75°C
[Programming/erasing conditions: Ta = 0°C to +75°C]
Item
Schmitt
trigger input
voltages
Input high
voltage
Input low
voltage
Symbol
Port A,
P80 to P82
VT
–
VT
+
+
VT – VT
–
Min
Typ
Max
Unit
1.0
—
—
V
—
—
VCC × 0.7
V
0.4
—
—
V
VCC – 0.7
—
VCC + 0.3
V
EXTAL
VCC × 0.7
—
VCC + 0.3
V
Port 7
2.0
—
AVCC + 0.3 V
Ports 1 to 6,
P83, P84, P90
to P95, port B
2.0
—
VCC + 0.3
V
–0.3
—
0.5
V
–0.3
—
0.8
V
—
—
V
STBY, RES,
VIH
Test
Conditions
NMI, MD2 to
MD0, FWE
STBY, RES,
VIL
FWE, MD2 to
MD0
NMI, EXTAL,
ports 1 to 7,
P83, P84, P90
to P95, port B
IOH = –200 µA
Output high
voltage
All output pins
VOH
VCC – 0.5
3.5
—
—
V
IOH = –1 mA
Output low
voltage
All output pins
VOL
—
—
0.4
V
IOL = 1.6 mA
—
—
1.0
V
IOL = 10 mA
Ports 1, 2,
and 5
Rev. 3.00 Sep 14, 2005 page 676 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Item
Test
Conditions
Symbol
Min
Typ
Max
Unit
|Iin|
—
—
1.0
µA
Vin = 0.5 V to
VCC – 0.5 V
—
—
1.0
µA
Vin = 0.5 V to
AVCC – 0.5 V
|ITSI|
—
—
1.0
µA
Vin = 0.5 V to
VCC – 0.5 V
Input pull-up Ports 2, 4,
MOS current and 5
–Ip
50
—
300
µA
Vin = 0 V
Input
capacitance
Cin
—
—
80
pF
NMI
—
—
50
pF
Vin = 0 V
f = fmin
Ta = 25°C
All input pins
except NMI
—
—
15
pF
—
32
47
(5.0 V)
mA
Input
leakage
current
STBY, RES,
NMI, FWE,
MD2 to MD0
Port 7
Three-state
leakage
current
Ports 1 to 6
Ports 8 to B
FWE
Current
Normal
2
dissipation* operation
ICC*4
37
58
(5.0 V)
Sleep mode
—
24
38
(5.0 V)
f = 25 MHz
mA
29
47
(5.0 V)
Module
standby mode
—
19
31
(5.0 V)
f = 20 MHz
f = 20 MHz
f = 25 MHz
mA
21
37
(5.0 V)
f = 20 MHz
f = 25 MHz
Standby
mode*3
—
1.0
10
µA
Ta ≤ 50°C
—
—
80
µA
50°C < Ta
Flash memory
programming/
erasing*5
—
37
57
mA
f = 20 MHz
42
68
f = 25 MHz
Rev. 3.00 Sep 14, 2005 page 677 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Item
Symbol
Min
Typ
Max
Unit
Analog
During A/D
power supply conversion
current
AICC
—
0.6
1.5
mA
During A/D
and D/A
conversion
—
0.6
1.5
mA
Idle
—
0.01
5
µA
—
0.45
0.8
mA
During A/D
and D/A
conversion
—
2.0
3.0
mA
Idle
—
0.01
5
µA
2.0
—
—
V
Reference
current
During A/D
conversion
RAM standby voltage
AICC
VRAM
Test
Conditions
DASTE = 0
DASTE = 0
Notes: 1. If the A/D converter is not used, do not leave the AVCC, VREF, and AVSS pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
2. Current dissipation values are for VIH min = VCC – 0.5 V and VIL max = 0.5 V with all
output pins unloaded and the on-chip MOS pull-up transistors in the off state.
3. The values are for VRAM ≤ VCC < 4.5 V, VIH min = VCC × 0.9, and VIL max = 0.3 V.
4. ICC max. (normal operation) = 3.0 (mA) + 0.40 (mA/(MHz × V)) × VCC × f
ICC max. (sleep mode)
= 3.0 (mA) + 0.32 (mA/(MHz × V)) × VCC × f
ICC max. (sleep mode + module standby mode)
= 3.0 (mA) + 0.25 (mA/(MHz × V)) × VCC × f
The Typ values for power consumption are reference values.
5. Sum of current dissipation in normal operation and current dissipation in
program/erase operations.
Rev. 3.00 Sep 14, 2005 page 678 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Table 21.3 Permissible Output Currents
Conditions: VCC = 4.5 V to 5.5 V, AVCC = 4.5 V to 5.5 V, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, Ta = –40°C to +75°C
Item
Permissible output
low current (per pin)
Ports 1, 2, and 5
Permissible output
low current (total)
Total of 20 pins in
Ports 1, 2, and 5
Symbol
Min
Typ
Max
Unit
IOL
—
—
10
mA
—
—
2.0
mA
—
—
80
mA
—
—
120
mA
Other output pins
ΣIOL
Total of all output pins,
including the above
Permissible output
high current (per pin)
All output pins
| –IOH |
—
—
2.0
mA
Permissible output
high current (total)
Total of all output pins
| ΣIOH |
—
—
40
mA
Notes: 1. To protect chip reliability, do not exceed the output current values in table 21.3.
2. When directly driving a darlington pair or LED, always insert a current-limiting resistor
in the output line, as shown in figures 21.1 and 21.2.
H8/3068F-ZTAT
2 kΩ
Port
Darlington pair
Figure 21.1 Darlington Pair Drive Circuit (Example)
Rev. 3.00 Sep 14, 2005 page 679 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
H8/3068F-ZTAT
600 Ω
Ports 1, 2, 5
LED
Figure 21.2 Sample LED Circuit
Rev. 3.00 Sep 14, 2005 page 680 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.1.3
AC Characteristics
Clock timing parameters are listed in table 21.4, control signal timing parameters in table 21.5,
and bus timing parameters in table 21.6. Timing parameters of the on-chip supporting modules
are listed in table 21.7.
Table 21.4 Clock Timing
Condition:
Ta = –20°C to +75°C
Condition A: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 20 MHz
Condition B: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 25 MHz
Condition
A
Item
Symbol
Min
Clock cycle time
tcyc
Clock pulse low width
tCL
Clock pulse high width
B
Max
Min
Max
Unit
Test Conditions
50
500
40
500
ns
15
—
10
—
ns
Figure 21.4 to figure
21.6
tCH
15
—
10
—
ns
Clock rise time
tCr
—
10
—
10
ns
Clock fall time
tCf
—
10
—
10
ns
Clock oscillator settling
time at reset
tOSC1
20
—
20
—
ms
Clock oscillator settling
time in software standby
tOSC2
7
—
7
—
ms
Figure 21.4
Rev. 3.00 Sep 14, 2005 page 681 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Table 21.5 Control Signal Timing
Condition:
Ta = –20°C to +75°C
Condition A: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 20 MHz
Condition B: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 25 MHz
Condition
A and B
Item
Symbol
Min
Max
Unit
Test Conditions
Figure 21.5
RES setup time
RES pulse width
tRESS
150
—
ns
tRESW
20
—
tcyc
Mode programming setup time
tMDS
200
—
ns
NMI, IRQ setup time
tNMIS
150
—
ns
NMI, IRQ hold time
tNMIH
10
—
ns
NMI, IRQ pulse width
tNMIW
200
—
ns
Rev. 3.00 Sep 14, 2005 page 682 of 910
REJ09B0258-0300
Figure 21.7
Section 21 Electrical Characteristics
Table 21.6 Bus Timing
Condition:
Ta = –20°C to +75°C
Condition A: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 20 MHz
Condition B: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 25 MHz
Condition
A and B
Item
Symbol
Min
Max
Unit
Test
Conditions
Address delay time
tAD
—
Address hold time
tAH
0.5 tcyc – 20
25
ns
—
ns
Figure 21.8,
figure 21.9
Read strobe delay time
tRSD
—
25
ns
Address strobe delay time
tASD
—
25
ns
Write strobe delay time
tWSD
—
25
ns
Strobe delay time
tSD
—
25
ns
Write strobe pulse width 1
tWSW1
1.0 tcyc – 25
—
ns
Write strobe pulse width 2
tWSW2
1.5 tcyc – 25
—
ns
Address setup time 1
tAS1
0.5 tcyc – 20
—
ns
Address setup time 2
tAS2
1.0 tcyc – 20
—
ns
Read data setup time
tRDS
25
—
ns
Read data hold time
tRDH
0
—
ns
Write data delay time
tWDD
—
35
ns
Write data setup time 1
tWDS1
1.0 tcyc – 30
—
ns
Write data setup time 2
tWDS2
2.0 tcyc – 30
—
ns
Write data hold time
tWDH
0.5 tcyc – 15
—
ns
Read data access time 1
tACC1
—
2.0 tcyc – 45
ns
Read data access time 2
tACC2
—
3.0 tcyc – 45
ns
Read data access time 3
tACC3
—
1.5 tcyc – 45
ns
Read data access time 4
tACC4
—
2.5 tcyc – 45
ns
Precharge time 1
tPCH1
1.0 tcyc – 20
—
ns
Precharge time 2
tPCH2
0.5 tcyc – 20
—
ns
Figure 21.17,
figure 21.18
Rev. 3.00 Sep 14, 2005 page 683 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Condition
A and B
Item
Symbol Min
Max
Unit
Test
Conditions
Wait setup time
tWTS
25
—
ns
Figure 21.19
Wait hold time
tWTH
5
—
ns
Bus request setup time
tBRQS
25
—
ns
Bus acknowledge delay time 1 tBACD1
—
30
ns
Bus acknowledge delay time 2 tBACD2
—
30
ns
Bus-floating time
RAS precharge time
CAS precharge time
Low address hold time
RAS delay time 1
RAS delay time 2
CAS delay time 1
CAS delay time 2
WE delay time
CAS pulse width 1
CAS pulse width 2
CAS pulse width 3
RAS access time
Address access time
CAS access time
WE setup time
WE hold time
Write data setup time
WE write data hold time
CAS setup time 1
CAS setup time 2
CAS hold time
RAS pulse width
tBZD
—
30
ns
tRP
1.5 tcyc – 25
—
ns
tCP
0.5 tcyc – 15
—
ns
tRAH
0.5 tcyc – 15
—
ns
tRAD1
—
25
ns
tRAD2
—
30
ns
tCASD1
—
25
ns
tCASD2
—
25
ns
tWCD
—
25
ns
tCAS1
1.5 tcyc – 20
—
ns
tCAS2
1.0 tcyc – 20
—
ns
tCAS3
1.0 tcyc – 20
—
ns
tRAC
—
2.5 tcyc – 40
ns
tAA
—
2.0 tcyc – 50
ns
tCAC
—
1.5 tcyc – 50
ns
tWCS
0.5 tcyc – 20
—
ns
tWCH
0.5 tcyc – 15
—
ns
tWDS
0.5 tcyc – 20
—
ns
tWDH
0.5 tcyc – 15
—
ns
tCSR1
0.5 tcyc – 20
—
ns
tCSR2
0.5 tcyc – 15
—
ns
tCHR
0.5 tcyc – 15
—
ns
tRAS
1.5 tcyc – 15
—
ns
Figure 21.20
Figure 21.17 to
figure 21.19
Note: In order to secure the address hold time relative to the rise of the RD strobe, address
update mode 2 should be used. For details see section 6.3.5, Address Output Method.
Rev. 3.00 Sep 14, 2005 page 684 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Table 21.7 Timing of On-Chip Supporting Modules
Condition:
Ta = –20°C to +75°C
Condition A: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 20 MHz
Condition B: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 25 MHz
Condition
A and B
Module
Item
Symbol
Min
Max
Unit
Test Conditions
Ports and
TPC
Output data delay time
tPWD
—
50
ns
Figure 21.21
Input data setup time
tPRS
50
—
ns
Input data hold time
tPRH
50
—
ns
16-bit timer
Timer output delay time
tTOCD
—
50
ns
Timer input setup time
tTICS
50
—
ns
Timer clock input setup time
tTCKS
50
—
ns
Timer clock Single edge
pulse width Both edges
tTCKWH
1.5
—
tcyc
tTCKWL
2.5
—
tcyc
Timer output delay time
tTOCD
—
50
ns
Timer input setup time
tTICS
50
—
ns
Timer clock input setup time
tTCKS
50
—
ns
Timer clock Single edge
pulse width Both edges
tTCKWH
1.5
—
tcyc
tTCKWL
2.5
—
tcyc
8-bit timer
Figure 21.22
Figure 21.23
Figure 21.22
Figure 21.23
Rev. 3.00 Sep 14, 2005 page 685 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Condition
A and B
Module
Item
SCI
Input clock
cycle
DMAC
Symbol
Min
Max
Unit
Test Conditions
tScyc
4
—
tcyc
Figure 21.24
6
—
tcyc
Input clock rise time
tSCKr
—
1.5
tcyc
Input clock fall time
tSCKf
—
1.5
tcyc
Input clock
pulse width
tSCKW
0.4
0.6
tScyc
Transmit data delay time
tTXD
—
100
ns
Receive data setup time
(synchronous)
tRXS
100
—
ns
Receive
data hold
time (synchronous)
tRXH
100
—
ns
0
—
ns
tTED1
—
50
ns
tTED2
—
50
ns
Figure 21.25,
figure 21.26
tDRQS
25
—
ns
Figure 21.27
tDRQH
10
—
ns
Asynchronous
Synchronous
Clock input
Clock output
TEND delay time 1
TEND delay time 2
DREQ setup time
DREQ hold time
RL
H8/3068F-ZTAT
output pin
Figure 21.25
C = 90 pF: ports 1 to 6, 8
C = 30 pF: ports 9, A, B
R L = 2.4 k Ω
R H = 12 k Ω
C
RH
Input/output timing measurement
levels
• Low: 0.8 V
• High: 2.0 V
Figure 21.3 Output Load Circuit
Rev. 3.00 Sep 14, 2005 page 686 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.1.4
A/D Conversion Characteristics
Table 21.8 lists the A/D conversion characteristics.
Table 21.8 A/D Conversion Characteristics
Condition:
Ta = –20°C to +75°C
Condition A: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 20 MHz
Condition B: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 25 MHz
Condition
A and B
Item
Min
Typ
Max
Unit
Conversion time: Resolution
134 states
Conversion time (single mode)
10
10
10
bits
—
—
134
tcyc
Analog input capacitance
—
—
20
pF
φ ≤ 13 MHz
—
—
10
kΩ
φ > 13 MHz
—
—
5
kΩ
4.0 V ≤ AVCC ≤ 5.5 V —
—
—
kΩ
3.0 V ≤ AVCC < 4.0 V —
—
—
kΩ
Nonlinearity error
—
—
±3.5
LSB
Offset error
—
—
±3.5
LSB
Full-scale error
—
—
±3.5
LSB
Quantization error
—
—
±0.5
LSB
Absolute accuracy
—
—
±4.0
LSB
Permissible signalsource impedance
Rev. 3.00 Sep 14, 2005 page 687 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Condition
A and B
Item
Min
Typ
Max
Unit
Conversion time: Resolution
70 states
Conversion time (single mode)
10
10
10
bits
—
—
70
tcyc
Analog input capacitance
—
—
20
pF
φ ≤ 13 MHz
—
—
5
kΩ
φ > 13 MHz
—
—
3
kΩ
4.0 V ≤ AVCC ≤ 5.5 V —
—
—
kΩ
3.0 V ≤ AVCC < 4.0 V —
—
—
kΩ
Nonlinearity error
—
—
±7.5
LSB
Offset error
—
—
±7.5
LSB
Full-scale error
—
—
±7.5
LSB
Quantization error
—
—
±0.5
LSB
Absolute accuracy
—
—
±8.0
LSB
Permissible signalsource impedance
Rev. 3.00 Sep 14, 2005 page 688 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.1.5
D/A Conversion Characteristics
Table 21.9 lists the D/A conversion characteristics.
Table 21.9 D/A Conversion Characteristics
Condition:
Ta = –20°C to +75°C
Condition A: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 20 MHz
Condition B: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 to AVCC, VSS = AVSS = 0 V,
fmax = 25 MHz
Condition
A and B
Item
Min
Typ
Max
Unit
Test Conditions
Resolution
8
8
8
bits
Conversion time (centering time)
—
—
10
µs
20 pF capacitive load
Absolute accuracy
—
±1.5
±2.0
LSB
2 MΩ resistive load
—
—
±1.5
LSB
4 MΩ resistive load
Rev. 3.00 Sep 14, 2005 page 689 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.1.6
Flash Memory Characteristics
Table 21.10 shows the flash memory characteristics.
Table 21.10 Flash Memory Characteristics
Conditions: VCC = 4.5 to 5.5 V, AVCC = 4.5 to 5.5 V, VSS = AVSS = 0 V,
Ta = 0°C to +75°C (operating temperature range for programming/erasing)
Item
Symbol Min
Typ
Max
Unit
Programming time* * *
tP
—
10
200
ms/
128 bytes
1
tE
—
1200
ms/block
1
3
2
4
5
Erase time* * *
100
6
7
Notes
Reprogramming count
NWEC
100*
10,000*
—
Times
Data retention period
tDRP
10*8
—
—
Years
Programming Wait time after SWE bit setting*
tsswe
1
1
—
µs
1
tspsu
50
50
—
µs
tsp30
28
30
32
µs
Programming
time wait
tsp200
198
200
202
µs
Programming
time wait
tsp10
8
10
12
µs
Additionalprogramming
time wait
1
Wait time after PSU bit setting*
1
4
Wait time after P bit setting* *
1
Wait time after P bit clear*
tcp
5
5
—
µs
1
tcpsu
5
5
—
µs
1
Wait time after PV bit setting*
tspv
4
4
—
µs
Wait time after H'FF dummy
1
write*
tspvr
2
2
—
µs
tcpv
2
2
—
µs
Wait time after SWE bit clear*
tcswe
100
100
—
µs
Maximum programming
1 4
count* *
N
—
—
1000
Times
tsswe
1
1
—
µs
Wait time after ESU bit setting*
tsesu
100
100
—
µs
Wait time after E bit setting*1 *5
tse
10
10
100
ms
Wait time after E bit clear*1
tce
10
10
—
µs
tcesu
10
10
—
µs
Wait time after PSU bit clear*
Wait time after PV bit clear*1
1
Erase
Wait time after SWE bit setting*1
1
1
Wait time after ESU bit clear*
Rev. 3.00 Sep 14, 2005 page 690 of 910
REJ09B0258-0300
Erase time
wait
Section 21 Electrical Characteristics
Item
Erase
Symbol Min
Typ
Max
Unit
Wait time after EV bit setting*
tsev
20
20
—
µs
Wait time after H'FF dummy
1
write*
tsevr
2
2
—
µs
tcev
4
4
—
µs
tcswe
100
100
—
µs
N
12
—
120
Times
1
1
Wait time after EV bit clear*
1
Wait time after SWE bit clear*
1
4
Maximum erase count* *
Notes
Notes: 1. Make each time setting in accordance with the program/program-verify flowchart or
erase/erase-verify flowchart.
2. Programming time per 128 bytes (Shows the total period for which the P-bit in the flash
memory control register (FLMCR1) is set. It does not include the programming
verification time.)
3. Block erase time (Shows the total period for which the E-bit in FLMCR1 is set. It does
not include the erase verification time.)
4. To specify the maximum programming time (tP(max)) in the 128-byte programming
flowchart, set the maximum value (1000) for the maximum programming count (N).
The wait time after P bit setting should be changed as follows according to the value of
the programming counter (n).
Programming counter (n) = 1 to 6:
tsp30 = 30 µs
Programming counter (n) = 7 to 1000:
tsp200 = 200 µs
Programming counter (n) [in additional programming] = 1 to 6: tsp10 = 10 µs
5. For the maximum erase time (tE(max)), the following relationship applies between the
wait time after E bit setting (tse) and the maximum erase count (N):
tE(max) = Wait time after E bit setting (tse) × maximum erase count (N)
To set the maximum erase time, the values of tse and N should be set so as to satisfy
the above formula.
Examples: When tse = 100 [ms], N = 12 times
When tse = 10 [ms], N = 120 times
6. Minimum number of times at which all characteristics are guaranteed after
reprogramming. (Reprogramming count from 1 to minimum value is guaranteed.)
7. Reference characteristics at 25°C. (This is an indication that reprogramming operations
can normally be performed up to this figure.)
8. Data retention characteristics when reprogramming is performed correctly within the
specification values, including the minimum data retention period.
Rev. 3.00 Sep 14, 2005 page 691 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.2
Operational Timing
This section shows timing diagrams.
21.2.1
Clock Timing
Clock timing is shown as follows:
• Oscillator settling timing
Figure 21.4 shows the oscillator settling timing.
φ
VCC
STBY
tOSC1
tOSC1
RES
Figure 21.4 Oscillator Settling Timing
Rev. 3.00 Sep 14, 2005 page 692 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.2.2
Control Signal Timing
Control signal timing is shown as follows:
• Reset input timing
Figure 21.5 shows the reset input timing.
• Reset output timing*
Figure 21.6 shows the reset output timing.
• Interrupt input timing
Figure 21.7 shows the interrupt input timing for NMI and IRQ5 to IRQ0.
φ
tRESS
tRESS
RES
tMDS
tRESW
FWE
MD2 to MD0
Figure 21.5 Reset Input Timing
φ
tRESD
tRESD
RESO
tRESOW
Figure 21.6 Reset Output Timing*
Note: * This function is used only in mask ROM models, and is not provided in flash memory
models.
Rev. 3.00 Sep 14, 2005 page 693 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
φ
tNMIS
tNMIH
tNMIS
tNMIH
NMI
IRQ E
tNMIS
IRQ L
IRQ E : Edge-sensitive IRQ i
IRQ L : Level-sensitive IRQ i (i = 0 to 5)
tNMIW
NMI
IRQ j
(j = 0 to 5)
Figure 21.7 Interrupt Input Timing
21.2.3
Bus Timing
Bus timing is shown as follows:
• Basic bus cycle: two-state access
Figure 21.8 shows the timing of the external two-state access cycle.
• Basic bus cycle: three-state access
Figure 21.9 shows the timing of the external three-state access cycle.
• Basic bus cycle: three-state access with one wait state
Figure 21.10 shows the timing of the external three-state access cycle with one wait state
inserted.
• Bus-release mode timing
Figure 21.11 shows the bus-release mode timing.
Rev. 3.00 Sep 14, 2005 page 694 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
T1
tcyc
T2
tCH
tCL
φ
tCf
tAD
tcyc
tCr
A23 to A0,
CSn
tPCH1
AS
RD
(read)
tASD
tACC3
tASD
tACC3
tSD
tAH
tAS1
tRSD
tPCH2
tAS1
tACC1
tRDH*
tRDS
D15 to D0
(read)
tPCH1
tASD
HWR, LWR
(write)
tSD
tAH
tAS1
tWDD
tWSW1
tWDS1
tWDH
D15 to D0
(write)
Note: * Specification from the earliest negation timing of A23 to A0, CSn, and RD.
Figure 21.8 Basic Bus Cycle: Two-State Access
Rev. 3.00 Sep 14, 2005 page 695 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
T1
T2
T3
φ
A23 to A0,
CSn
tACC4
AS
tACC4
RD
(read)
tACC2
tRDS
D15 to D0
(read)
tWSD
HWR, LWR
(write)
tWSW2
tAS2
tWDD
tWDS2
D15 to D0
(write)
Figure 21.9 Basic Bus Cycle: Three-State Access
Rev. 3.00 Sep 14, 2005 page 696 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
T1
T2
TW
T3
φ
A23 to A0,
CSn
AS
RD (read)
D15 to D0
(read)
HWR, LWR
(write)
D15 to D0
(write)
tWTS
tWTH
tWTS
tWTH
WAIT
Figure 21.10 Basic Bus Cycle: Three-State Access with One Wait State
Rev. 3.00 Sep 14, 2005 page 697 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
T1
T2
T3
T1
T2
φ
tAD
tAD
A23 to A3
CSn
A2 to A0
tASD
AS
tACC4
tAH
tAS1
tASD
tSD
tAH
tAS1
tASD
RD
tSD
tRSD
tACC4
tAS1
tACC2
tRDS
tACC1
tRDH*
tRDS
D15 to D0
Note: * Specification from the earliest negation timing of A23 to A0, CSn, and RD.
Figure 21.11 Burst ROM Access Timing: Two-State Access
Rev. 3.00 Sep 14, 2005 page 698 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
T1
T2
T3
T1
T2
T3
φ
tAD
tAD
A23 to A3
CSn
A2 to A0
tASD
AS
tACC4
tAH
tAS1
tASD
tSD
tAH
tAS1
tASD
RD
tSD
tRSD
tACC4
tRDH*
tAS1
tACC2
tACC2
tRDS
tRDS
D15 to D0
Note: * Specification from the earliest negation timing of A23 to A0, CSn, and RD.
Figure 21.12 Burst ROM Access Timing: Three-State Access
φ
tBRQS
tBRQS
BREQ
tBACD2
tBACD1
BACK
A23 to A0,
AS, RD,
HWR, LWR
tBZD
tBZD
Figure 21.13 Bus-Release Mode Timing
Rev. 3.00 Sep 14, 2005 page 699 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.2.4
DRAM Interface Bus Timing
DRAM interface bus timing is shown as follows:
• DRAM bus timing: read and write access
Figure 21.14 shows the timing of the read and write access.
• DRAM bus timing: CAS before RAS refresh
Figure 21.15 shows the timing of the CAS before RAS refresh.
• DRAM bus timing: self-refresh
Figure 21.16 shows the timing of the self-refresh.
Rev. 3.00 Sep 14, 2005 page 700 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
Tp
Tr
TC1
TC2
φ
tAD
tAD
tAD
A23 to A0
tAS1
tRAH
tRAD2
tRP
CS5 to CS2
(RAS5 to RAS2)
tRAD1
tCASD2
tASD
tCAS1
UCAS, LCAS
(read)
tCP
RD (WE)
(read)
High
tRAC
tRDS
tRDH*
tAA
D15 to D0
(read)
tCAC
tCASD2
tCASD1
tCAS2
UCAS, LCAS
(write)
tCP
tASD
tWCD
RD (WE)
(write)
tWCS
tWDD
tWCH
tWDS
tWDH
D15 to D0
(write)
RFSH
High
Note: * Specification from the earliest negation timing of RAS and CAS.
Figure 21.14 DRAM Bus Timing (Read/Write)
Rev. 3.00 Sep 14, 2005 page 701 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
TRp
TR1
TR2
φ
tRAD1
tRAD2
tRP
CS5 to CS2
(RAS5 to
RAS2)
tRAS
tCASD1
tCASD2
tCSR1
tCHR
tCAS3
UCAS,
LCAS
RD (WE)
(high)
tRAD2
tRAD1
tCSR1
tCHR
tRAS
RFSH
Figure 21.15 DRAM Bus Timing (CAS Before RAS Refresh)
Rev. 3.00 Sep 14, 2005 page 702 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
φ
tCSR2
CS5 to CS2
(RAS5 to
RAS2)
UCAS,
LCAS
RD (WE)
(high)
tCSR2
RFSH
Figure 21.16 DRAM Bus Timing (Self-Refresh)
21.2.5
TPC and I/O Port Timing
Figure 21.17 shows the TPC and I/O port input/output timing.
T1
T2
T3
φ
tPRS
tPRH
Port 1 to
B (read)
tPWD
Port 1 to
6, 8 to B
(write)
Figure 21.17 TPC and I/O Port Input/Output Timing
Rev. 3.00 Sep 14, 2005 page 703 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.2.6
Timer Input/Output Timing
16-bit timer and 8-bit timer timing is shown below.
• Timer input/output timing
Figure 21.18 shows the timer input/output timing.
• Timer external clock input timing
Figure 21.19 shows the timer external clock input timing.
φ
tTOCD
Output
compare*1
tTICS
Input
capture*2
Notes: 1. TIOCA0 to TIOCA2, TIOCB0 to TIOCB2, TMO0, TMO2, TMIO1, TMIO3
2. TIOCA0 to TIOCA2, TIOCB0 to TIOCB2, TMIO1, TMIO3
Figure 21.18 Timer Input/Output Timing
tTCKS
φ
tTCKS
TCLKA to
TCLKD
tTCKWL
tTCKWH
Figure 21.19 Timer External Clock Input Timing
Rev. 3.00 Sep 14, 2005 page 704 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.2.7
SCI Input/Output Timing
SCI timing is shown as follows:
• SCI input clock timing
Figure 21.20 shows the SCI input clock timing.
• SCI input/output timing (synchronous mode)
Figure 21.21 shows the SCI input/output timing in synchronous mode.
tSCKW
tSCKr
tSCKf
SCK0, SCK1
tScyc
Figure 21.20 SCI Input Clock Timing
tScyc
SCK0,
SCK1
tTXD
TxD0, TxD1
(transmit
data)
tRXS
tRXH
RxD0, RxD1
(receive
data)
Figure 21.21 SCI Input/Output Timing in Synchronous Mode
Rev. 3.00 Sep 14, 2005 page 705 of 910
REJ09B0258-0300
Section 21 Electrical Characteristics
21.2.8
DMAC Timing
DMAC timing is shown as follows.
• DMAC TEND output timing for 2 state access
Figure 21.22 shows the DMAC TEND output timing for 2 state access.
• DMAC TEND output timing for 3 state access
Figure 21.23 shows the DMAC TEND output timing for 3 state access.
• DMAC DREQ input timing
Figure 21.24 shows DMAC DREQ input timing.
T1
T2
φ
tTED1
tTED2
TEND
Figure 21.22 DMAC TEND Output Timing for 2 State Access
T1
T2
T3
φ
tTED2
tTED1
TEND
Figure 21.23 DMAC TEND Output Timing for 3 State Access
φ
tDRQS
tDRQH
DREQ
Figure 21.24 DMAC DREQ Input Timing
Rev. 3.00 Sep 14, 2005 page 706 of 910
REJ09B0258-0300
Appendix A Instruction Set
Appendix A Instruction Set
A.1
Instruction List
Operand Notation
Symbol
Description
Rd
General destination register
Rs
General source register
Rn
General register
ERd
General destination register (address register or 32-bit register)
ERs
General source register (address register or 32-bit register)
ERn
General register (32-bit register)
(EAd)
Destination operand
(EAs)
Source operand
PC
Program counter
SP
Stack pointer
CCR
Condition code register
N
N (negative) flag in CCR
Z
Z (zero) flag in CCR
V
V (overflow) flag in CCR
C
C (carry) flag in CCR
disp
Displacement
→
Transfer from the operand on the left to the operand on the right, or transition from
the state on the left to the state on the right
+
Addition of the operands on both sides
–
Subtraction of the operand on the right from the operand on the left
×
Multiplication of the operands on both sides
÷
Division of the operand on the left by the operand on the right
∧
Logical AND of the operands on both sides
∨
Logical OR of the operands on both sides
⊕
Exclusive logical OR of the operands on both sides
¬
NOT (logical complement)
( ), < >
Contents of operand
Note: General registers include 8-bit registers (R0H to R7H and R0L to R7L) and 16-bit registers
(R0 to R7 and E0 to E7).
Rev. 3.00 Sep 14, 2005 page 707 of 910
REJ09B0258-0300
Appendix A Instruction Set
Condition Code Notation
Symbol
Description
Changed according to execution result
*
Undetermined (no guaranteed value)
0
Cleared to 0
1
Set to 1
—
Not affected by execution of the instruction
∆
Varies depending on conditions, described in notes
Rev. 3.00 Sep 14, 2005 page 708 of 910
REJ09B0258-0300
Appendix A Instruction Set
Table A.1
Instruction Set
1. Data transfer instructions
4
Rs8 → @(d:16, ERd)
— —
8
Rs8 → @(d:24, ERd)
— —
ERd32–1 → ERd32
Rs8 → @ERd
— —
2
Rs8 → @aa:8
— —
4
Rs8 → @aa:16
— —
6
Rs8 → @aa:24
— —
#xx:16 → Rd16
— —
Rs16 → Rd16
— —
@ERs → Rd16
— —
↔ ↔ ↔ ↔
— —
↔ ↔ ↔ ↔
— —
Rs8 → @ERd
↔
@aa:24 → Rd8
↔
6
↔
— —
↔
— —
@aa:16 → Rd8
↔
@aa:8 → Rd8
4
↔
0 —
0 —
0 —
0 —
0 —
0 —
0 —
MOV.W @(d:16,
ERs), Rd
W
4
@(d:16, ERs) → Rd16
— —
MOV.W @(d:24,
ERs), Rd
W
8
@(d:24, ERs) → Rd16
— —
0 —
MOV.W @ERs+, Rd
W
@ERs → Rd16
ERs32+2 → @ERd32
— —
0 —
@aa:16 → Rd16
— —
0 —
MOV.B Rs, @aa:24
B
MOV.W #xx:16, Rd
W 4
MOV.W Rs, Rd
W
MOV.W @ERs, Rd
W
MOV.W @aa:16, Rd W
2
2
2
2
2
2
2
2
4
Advanced
Normal
B
2
0 —
↔ ↔ ↔ ↔
B
MOV.B Rs, @aa:16
— —
↔ ↔ ↔ ↔
MOV.B Rs, @aa:8
@ERs → Rd8
ERs32+1 → ERs32
0 —
↔
B
— —
↔
MOV.B Rs, @–ERd
@(d:24, ERs) → Rd8
↔
B
8
↔
MOV.B Rs, @(d:24,
ERd)
— —
↔
B
@(d:16, ERs) → Rd8
↔
MOV.B Rs, @(d:16,
ERd)
4
↔ ↔ ↔ ↔
B
— —
↔ ↔ ↔ ↔
B
MOV.B Rs, @ERd
@ERs → Rd8
0 —
↔ ↔
MOV.B @aa:24, Rd
— —
↔ ↔
B
— —
Rs8 → Rd8
C
↔
B
MOV.B @aa:16, Rd
#xx:8 → Rd8
V
↔
MOV.B @aa:8, Rd
Z
↔
B
H N
↔
MOV.B @ERs+, Rd
I
↔
B
Condition Code
Operation
↔
MOV.B @(d:24,
ERs), Rd
No. of
States*1
—
B
@@aa
MOV.B @(d:16,
ERs), Rd
@(d, PC)
B
@aa
MOV.B @ERs, Rd
@–ERn/@ERn+
2
B
@(d, ERn)
B
MOV.B Rs, Rd
@ERn
#xx
MOV.B #xx:8, Rd
Rn
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
2
0 —
2
0 —
4
0 —
6
10
6
4
6
0 —
8
0 —
4
0 —
6
10
6
4
6
0 —
8
0 —
4
0 —
2
4
0 —
6
10
6
6
Rev. 3.00 Sep 14, 2005 page 709 of 910
REJ09B0258-0300
Appendix A Instruction Set
Operation
↔
↔
↔ ↔
↔ ↔
↔
↔
0 —
↔
↔
0 —
↔
↔
0 —
↔ ↔
0 —
0 —
↔
0 —
↔ ↔
↔ ↔
0 —
0 —
↔
↔
0 —
↔
↔
0 —
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
0 —
0 —
↔
↔
0 —
↔
↔
0 —
0 —
0 —
POP.W Rn
W
2 @SP → Rn16
SP+2 → SP
— —
0 —
POP.L ERn
L
4 @SP → ERn32
SP+4 → SP
— —
0 —
Rs16 → @ERd
— —
MOV.W Rs, @(d:16, W
ERd)
4
Rs16 → @(d:16, ERd)
— —
MOV.W Rs, @(d:24, W
ERd)
8
Rs16 → @(d:24, ERd)
— —
ERd32–2 → ERd32
Rs16 → @ERd
— —
MOV.W Rs, @ERd
W
MOV.W Rs, @–ERd
W
MOV.W Rs, @aa:16
W
MOV.W Rs, @aa:24
W
MOV.L #xx:32, Rd
L
MOV.L ERs, ERd
L
MOV.L @ERs, ERd
L
2
2
4
Rs16 → @aa:16
— —
6
Rs16 → @aa:24
— —
#xx:32 → Rd32
— —
ERs32 → ERd32
— —
@ERs → ERd32
— —
6
2
4
MOV.L @(d:16, ERs), L
ERd
6
@(d:16, ERs) → ERd32 — —
MOV.L @(d:24, ERs), L
ERd
10
@(d:24, ERs) → ERd32 — —
MOV.L @ERs+, ERd L
4
@ERs → ERd32
ERs32+4 → ERs32
— —
MOV.L @aa:16, ERd L
6
@aa:16 → ERd32
— —
MOV.L @aa:24, ERd L
8
@aa:24 → ERd32
— —
ERs32 → @ERd
— —
MOV.L ERs, @ERd
L
4
MOV.L ERs, @(d:16, L
ERd)
6
ERs32 → @(d:16, ERd) — —
MOV.L ERs, @(d:24, L
ERd)
10
ERs32 → @(d:24, ERd) — —
MOV.L ERs, @–ERd L
MOV.L ERs, @aa:16 L
MOV.L ERs, @aa:24 L
ERd32–4 → ERd32
ERs32 → @ERd
4
— —
6
ERs32 → @aa:16
— —
8
ERs32 → @aa:24
— —
Rev. 3.00 Sep 14, 2005 page 710 of 910
REJ09B0258-0300
↔
6
↔ ↔
0 —
↔
C
↔
V
↔ ↔
Z
↔ ↔
I
↔
H N
— —
↔
@aa:24 → Rd16
0 —
MOV.W @aa:24, Rd W
Normal
Condition Code
Advanced
No. of
States*1
—
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
8
0 —
4
6
10
6
6
8
6
2
8
10
14
10
10
0 —
12
0 —
8
10
14
10
10
12
6
10
Appendix A Instruction Set
— —
MOVFPE @aa:16,
Rd
B
4
Cannot be used in the
H8/3068F
Cannot be used in the
H8/3068F
MOVTPE Rs,
@aa:16
B
4
Cannot be used in the
H8/3068F
Cannot be used in the
H8/3068F
Z
↔
V
C
↔
H N
0 —
6
↔
I
↔
—
Operation
Normal
4 SP–4 → SP
ERn32 → @SP
@@aa
L
@(d, PC)
PUSH.L ERn
@aa
— —
@(d, ERn)
2 SP–2 → SP
Rn16 → @SP
@ERn
W
Rn
PUSH.W Rn
#xx
Mnemonic
Condition Code
Advanced
No. of
States*1
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
0 —
10
Rev. 3.00 Sep 14, 2005 page 711 of 910
REJ09B0258-0300
Appendix A Instruction Set
2. Arithmetic instructions
H N
↔
↔
↔
↔ ↔ ↔
↔ ↔ ↔
↔
↔
↔
↔
2
(3)
↔
↔
2
(3)
↔
↔
2
— — — — — —
2
B
ADD.W #xx:16, Rd
W 4
ADD.W Rs, Rd
W
ADD.L #xx:32, ERd
L
ADD.L ERs, ERd
L
ADDX.B #xx:8, Rd
B
ADDX.B Rs, Rd
B
2
Rd8+Rs8 +C → Rd8
—
ADDS.L #1, ERd
L
2
ERd32+1 → ERd32
ADDS.L #2, ERd
L
2
ERd32+2 → ERd32
— — — — — —
2
ADDS.L #4, ERd
L
2
ERd32+4 → ERd32
INC.B Rd
B
2
Rd8+1 → Rd8
— —
INC.W #1, Rd
W
2
Rd16+1 → Rd16
— —
↔ ↔
6
ADD.B Rs, Rd
INC.W #2, Rd
W
2
Rd16+2 → Rd16
— —
↔
↔
—
↔ ↔ ↔
Rd8+#xx:8 +C → Rd8
↔
— (2)
2
↔
ERd32+ERs32 →
ERd32
↔
— (2)
↔
— (1)
ERd32+#xx:32 →
ERd32
↔ ↔ ↔
Rd16+Rs16 → Rd16
2
↔
— (1)
C
↔
—
Rd16+#xx:16 → Rd16
V
↔
Rd8+Rs8 → Rd8
Z
↔
—
↔
I
Rd8+#xx:8 → Rd8
↔
Operation
Normal
Condition Code
Advanced
No. of
States*1
—
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
2
@(d, ERn)
B
@ERn
#xx
ADD.B #xx:8, Rd
Rn
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Rev. 3.00 Sep 14, 2005 page 712 of 910
REJ09B0258-0300
—
— — — — —
2
—
2
—
↔ ↔
2
↔
2
2
↔ ↔
2
6
4
↔
2
—
2
2
Appendix A Instruction Set
↔
B
2
Rd8 decimal adjust
→ Rd8
— *
↔ ↔
↔ ↔
SUB.B Rs, Rd
B
2
Rd8–Rs8 → Rd8
—
↔
↔
↔
↔
2
SUB.W #xx:16, Rd
W 4
Rd16–#xx:16 → Rd16
— (1)
SUB.W Rs, Rd
W
Rd16–Rs16 → Rd16
— (1)
↔ ↔
↔ ↔
↔ ↔
↔ ↔
4
SUB.L #xx:32, ERd
L
ERd32–#xx:32
→ ERd32
— (2)
↔
↔
↔
↔
6
SUB.L ERs, ERd
L
ERd32–ERs32
→ ERd32
— (2)
↔
↔
↔
↔
2
SUBX.B #xx:8, Rd
B
Rd8–#xx:8–C → Rd8
—
2
Rd8–Rs8–C → Rd8
—
↔ ↔
↔ ↔
↔ ↔
2
B
↔ ↔
(3)
SUBX.B Rs, Rd
SUBS.L #1, ERd
L
2
ERd32–1 → ERd32
— — — — — —
2
SUBS.L #2, ERd
L
2
ERd32–2 → ERd32
— — — — — —
2
SUBS.L #4, ERd
L
2
ERd32–4 → ERd32
— — — — — —
2
DEC.B Rd
B
2
Rd8–1 → Rd8
— —
↔
↔
↔
DEC.W #1, Rd
W
2
Rd16–1 → Rd16
— —
DEC.W #2, Rd
W
2
Rd16–2 → Rd16
— —
DEC.L #1, ERd
L
2
ERd32–1 → ERd32
— —
DEC.L #2, ERd
L
2
ERd32–2 → ERd32
— —
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
DAS.Rd
B
2
Rd8 decimal adjust
→ Rd8
— *
↔
MULXU. B Rs, Rd
B
MULXU. W Rs, ERd
2
6
2
Normal
↔
C
—
2
—
2
* —
2
2
2
—
2
—
2
—
2
—
2
—
2
* —
2
2
Rd8 × Rs8 → Rd16
— — — — — —
(unsigned multiplication)
14
W
2
Rd16 × Rs16 → ERd32 — — — — — —
(unsigned multiplication)
22
MULXS. B Rs, Rd
B
4
Rd8 × Rs8 → Rd16
(signed multiplication)
— —
↔
(3)
V
↔
Z
— —
16
MULXS. W Rs, ERd
W
4
Rd16 × Rs16 → ERd32
(signed multiplication)
— —
↔
H N
↔
—
I
↔
2
Condition Code
Operation
Advanced
↔
DAA Rd
@@aa
— —
@(d, PC)
— —
ERd32+2 → ERd32
@aa
ERd32+1 → ERd32
2
@(d, ERn)
2
L
@ERn
L
INC.L #2, ERd
Rn
INC.L #1, ERd
#xx
Mnemonic
↔
No. of
States*1
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
— —
24
DIVXU. B Rs, Rd
B
2
Rd16 ÷ Rs8 → Rd16
(RdH: remainder, RdL:
quotient)
(unsigned division)
— — (6) (7) — —
14
Rev. 3.00 Sep 14, 2005 page 713 of 910
REJ09B0258-0300
Appendix A Instruction Set
No. of
States*1
4
Rd16 ÷ Rs8 → Rd16
(RdH: remainder,
RdL: quotient)
(signed division)
— — (8) (7) — —
16
DIVXS. W Rs, ERd
W
4
ERd32 ÷ Rs16 → ERd32 — — (8) (7) — —
(Ed: remainder,
Rd: quotient)
(signed division)
24
CMP.B #xx:8, Rd
B
2
0–Rd8 → Rd8
—
↔ ↔ ↔
W
2
0–Rd16 → Rd16
—
NEG.L ERd
L
2
0–ERd32 → ERd32
—
EXTU.W Rd
W
2
0 → (<bits 15 to 8>
of Rd16)
— — 0
EXTU.L ERd
L
2
0 → (<bits 31 to 16>
of ERd32)
— — 0
EXTS.W Rd
W
2
(<bit 7> of Rd16) →
— —
(<bits 15 to 8> of Rd16)
EXTS.L ERd
L
2
(<bit 15> of ERd32) →
(<bits 31 to 16> of
ERd32)
Normal
↔
B
NEG.W Rd
↔ ↔
↔
NEG.B Rd
↔ ↔ ↔
↔ ↔
— (2)
↔ ↔ ↔
↔
ERd32–ERs32
— —
2
↔ ↔ ↔
↔
2
↔ ↔
— (2)
6
↔ ↔
↔
↔ ↔
↔
L
↔ ↔
— (1)
ERd32–#xx:32
↔ ↔
↔
↔ ↔
↔
CMP.L ERs, ERd
↔
Rd16–Rs16
2
2
↔
L
↔
— (1)
0 —
2
↔
W
CMP.L #xx:32, ERd
Rev. 3.00 Sep 14, 2005 page 714 of 910
REJ09B0258-0300
—
Rd16–#xx:16
2
0 —
2
↔
CMP.W Rs, Rd
2
Rd8–Rs8
C
0 —
2
↔
B
W 4
6
—
V
CMP.W #xx:16, Rd
2
Rd8–#xx:8
Z
CMP.B Rs, Rd
2
↔
H N
↔
I
↔
Operation
↔ ↔
—
Condition Code
Advanced
B
@@aa
DIVXS. B Rs, Rd
@(d, PC)
22
@aa
ERd32 ÷ Rs16 → ERd32 — — (6) (7) — —
(Ed: remainder,
Rd: quotient)
(unsigned division)
@(d, ERn)
2
@ERn
W
Rn
DIVXU. W Rs, ERd
#xx
Mnemonic
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
0 —
2
4
2
2
2
Appendix A Instruction Set
3. Logic instructions
2
W
XOR.L #xx:32, ERd
L
2
ERd32∨ERs32 → ERd32 — —
Rd8⊕#xx:8 → Rd8
— —
Rd8⊕Rs8 → Rd8
— —
Rd16⊕#xx:16 → Rd16
— —
Rd16⊕Rs16 → Rd16
— —
XOR.L ERs, ERd
L
4
ERd32⊕ERs32 → ERd32 — —
NOT.B Rd
B
2
¬Rd8 → Rd8
NOT.W Rd
W
2
¬Rd16 → Rd16
— —
NOT.L ERd
L
2
¬Rd32 → Rd32
— —
— —
0 —
0 —
0 —
0 —
0 —
Advanced
Normal
—
@@aa
@(d, PC)
@aa
ERd32⊕#xx:32 → ERd32 — —
6
↔
XOR.W Rs, Rd
— —
↔
B
W 4
Rd16∨Rs16 → Rd16
↔ ↔ ↔
4
2
XOR.W #xx:16, Rd
— —
ERd32∨#xx:32 → ERd32 — —
6
XOR.B Rs, Rd
— —
Rd16∨#xx:16 → Rd16
↔ ↔ ↔
B
2
Rd8∨Rs8 → Rd8
↔ ↔ ↔
L
XOR.B #xx:8, Rd
2
— —
↔ ↔ ↔
L
OR.L ERs, ERd
Rd8∨#xx:8 → Rd8
↔ ↔ ↔
W
OR.L #xx:32, ERd
ERd32∧ERs32 → ERd32 — —
↔ ↔ ↔
OR.W Rs, Rd
— —
0 —
↔ ↔
B
W 4
Rd16∧Rs16 → Rd16
C
0 —
↔ ↔
4
2
OR.W #xx:16, Rd
— —
— —
ERd32∧#xx:32 → ERd32 — —
6
OR.B Rs, Rd
Rd8∧Rs8 → Rd8
Rd16∧#xx:16 → Rd16
V
↔
B
Z
↔
L
OR.B #xx:8, Rd
2
I
↔ ↔ ↔
L
AND.L ERs, ERd
2
H N
— —
↔ ↔ ↔
W
AND.L #xx:32, ERd
Rd8∧#xx:8 → Rd8
↔ ↔ ↔
AND.W Rs, Rd
Operation
↔ ↔ ↔
W 4
Condition Code
↔ ↔
B
AND.W #xx:16, Rd
No. of
States*1
↔ ↔
AND.B Rs, Rd
@–ERn/@ERn+
2
@(d, ERn)
B
@ERn
#xx
AND.B #xx:8, Rd
Rn
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
2
0 —
2
4
0 —
2
0 —
6
0 —
4
0 —
2
0 —
2
0 —
4
0 —
2
0 —
6
4
2
0 —
2
4
0 —
2
0 —
6
0 —
4
2
0 —
2
2
Rev. 3.00 Sep 14, 2005 page 715 of 910
REJ09B0258-0300
Appendix A Instruction Set
4. Shift instructions
B
2
ROTL.W Rd
W
2
ROTL.L ERd
L
2
ROTR.B Rd
B
2
ROTR.W Rd
W
2
ROTR.L ERd
L
2
Rev. 3.00 Sep 14, 2005 page 716 of 910
REJ09B0258-0300
LSB
— —
— —
— —
C
— —
MSB
LSB
— —
— —
C
MSB
LSB
— —
— —
↔
ROTL.B Rd
MSB
↔
2
↔ ↔ ↔
2
L
↔ ↔
W
ROTXR.L ERd
— —
↔
ROTXR.W Rd
C
— —
↔ ↔
2
LSB
↔
2
B
MSB
↔ ↔ ↔
L
ROTXR.B Rd
— —
2
2
↔ ↔
ROTXL.L ERd
C
2
2
↔
2
2
2
↔ ↔ ↔
W
— —
2
2
↔ ↔ ↔
ROTXL.W Rd
— —
2
2
↔ ↔
2
LSB
— —
↔
2
B
MSB
— —
2
↔ ↔
L
ROTXL.B Rd
C
↔
SHLR.L ERd
0
↔ ↔ ↔
2
— —
↔ ↔ ↔
2
W
— —
↔ ↔
B
SHLR.W Rd
LSB
↔ ↔
SHLR.B Rd
MSB
↔
2
↔
2
L
0
↔ ↔
W
SHLL.L ERd
0
— —
↔ ↔
SHLL.W Rd
C
— —
0
↔
2
↔
2
B
LSB
0
0
↔ ↔ ↔
L
SHLL.B Rd
MSB
— —
↔ ↔ ↔
SHAR.L ERd
— —
C
0
↔ ↔
2
— —
↔ ↔
2
W
— —
0
↔
B
SHAR.W Rd
LSB
↔
SHAR.B Rd
MSB
0
↔ ↔ ↔
2
C
↔ ↔ ↔
2
L
V
0
↔ ↔ ↔
W
SHAL.L ERd
0
Z
↔ ↔ ↔
SHAL.W Rd
C
H N
0
↔ ↔
I
— —
↔ ↔
Operation
2
0
Normal
Condition Code
Advanced
No. of
States*1
—
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
B
Rn
SHAL.B Rd
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
2
0
0
0
0
0
0
0
0
0
0
0
2
2
2
2
2
2
2
2
2
2
2
2
Appendix A Instruction Set
5. Bit manipulation instructions
B
BCLR Rn, Rd
B
BCLR Rn, @ERd
B
BCLR Rn, @aa:8
B
BNOT #xx:3, Rd
B
BNOT #xx:3, @ERd
B
BNOT #xx:3, @aa:8
B
BNOT Rn, Rd
B
BNOT Rn, @ERd
B
BNOT Rn, @aa:8
B
BTST #xx:3, Rd
B
BTST #xx:3, @ERd
B
BTST #xx:3, @aa:8
B
BTST Rn, Rd
B
BTST Rn, @ERd
B
BTST Rn, @aa:8
B
BLD #xx:3, Rd
B
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
V
C
Advanced
BCLR #xx:3, @aa:8
2
Z
Normal
B
H N
2
(#xx:3 of @ERd) ← 1
— — — — — —
8
(#xx:3 of @aa:8) ← 1
— — — — — —
8
(Rn8 of Rd8) ← 1
— — — — — —
2
(Rn8 of @ERd) ← 1
— — — — — —
8
(Rn8 of @aa:8) ← 1
— — — — — —
8
(#xx:3 of Rd8) ← 0
— — — — — —
2
(#xx:3 of @ERd) ← 0
— — — — — —
8
(#xx:3 of @aa:8) ← 0
— — — — — —
8
(Rn8 of Rd8) ← 0
— — — — — —
2
(Rn8 of @ERd) ← 0
— — — — — —
8
(Rn8 of @aa:8) ← 0
— — — — — —
8
(#xx:3 of Rd8) ←
¬ (#xx:3 of Rd8)
— — — — — —
2
(#xx:3 of @ERd) ←
¬ (#xx:3 of @ERd)
— — — — — —
8
(#xx:3 of @aa:8) ←
¬ (#xx:3 of @aa:8)
— — — — — —
8
(Rn8 of Rd8) ←
¬ (Rn8 of Rd8)
— — — — — —
2
(Rn8 of @ERd) ←
¬ (Rn8 of @ERd)
— — — — — —
8
(Rn8 of @aa:8) ←
¬ (Rn8 of @aa:8)
— — — — — —
8
¬ (#xx:3 of Rd8) → Z
— — —
¬ (#xx:3 of @ERd) → Z
— — —
¬ (#xx:3 of @aa:8) → Z
— — —
¬ (Rn8 of @Rd8) → Z
— — —
¬ (Rn8 of @ERd) → Z
— — —
¬ (Rn8 of @aa:8) → Z
— — —
(#xx:3 of Rd8) → C
— — — — —
— —
2
— —
6
— —
6
— —
2
— —
6
— —
6
↔
B
BCLR #xx:3, @ERd
4
I
— — — — — —
↔
BCLR #xx:3, Rd
4
Operation
(#xx:3 of Rd8) ← 1
↔ ↔ ↔
B
Condition Code
↔ ↔
B
BSET Rn, @aa:8
4
2
No. of
States*1
—
BSET Rn, @ERd
4
@@aa
B
2
@(d, PC)
B
BSET Rn, Rd
@aa
BSET #xx:3, @aa:8
@–ERn/@ERn+
B
@(d, ERn)
BSET #xx:3, @ERd
@ERn
B
Rn
BSET #xx:3, Rd
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
2
Rev. 3.00 Sep 14, 2005 page 717 of 910
REJ09B0258-0300
Appendix A Instruction Set
B
BIAND #xx:3, @ERd
B
4
2
BIAND #xx:3, @aa:8 B
BOR #xx:3, Rd
B
BOR #xx:3, @ERd
B
BOR #xx:3, @aa:8
B
BIOR #xx:3, Rd
B
BIOR #xx:3, @ERd
B
BIOR #xx:3, @aa:8
B
BXOR #xx:3, Rd
B
BXOR #xx:3, @ERd
B
BXOR #xx:3, @aa:8
B
BIXOR #xx:3, Rd
B
BIXOR #xx:3, @ERd B
BIXOR #xx:3, @aa:8 B
¬ (#xx:3 of @ERd) → C
— — — — —
6
¬ (#xx:3 of @aa:8) → C
— — — — —
6
C → (#xx:3 of Rd8)
— — — — — —
2
C → (#xx:3 of @ERd24)
— — — — — —
8
C → (#xx:3 of @aa:8)
— — — — — —
8
¬ C → (#xx:3 of Rd8)
— — — — — —
2
¬ C → (#xx:3 of @ERd24)
— — — — — —
8
¬ C → (#xx:3 of @aa:8)
— — — — — —
8
C∧(#xx:3 of Rd8) → C
— — — — —
C∧(#xx:3 of @ERd24) → C
— — — — —
C∧(#xx:3 of @aa:8) → C
— — — — —
C∧ ¬ (#xx:3 of Rd8) → C
— — — — —
4
2
4
4
2
4
4
2
4
4
2
4
4
Rev. 3.00 Sep 14, 2005 page 718 of 910
REJ09B0258-0300
2
2
6
6
6
2
6
C∨ ¬ (#xx:3 of @aa:8) → C
— — — — —
C⊕(#xx:3 of Rd8) → C
— — — — —
C⊕(#xx:3 of @ERd24) → C
— — — — —
6
C⊕(#xx:3 of @aa:8) → C
— — — — —
C⊕ ¬ (#xx:3 of Rd8) → C
— — — — —
2
C⊕ ¬ (#xx:3 of @ERd24) → C
— — — — —
6
C⊕ ¬ (#xx:3 of @aa:8) → C
— — — — —
C∧ ¬ (#xx:3 of @ERd24) → C — — — — —
4
Advanced
BIAND #xx:3, Rd
4
Normal
B
↔
B
BAND #xx:3, @aa:8
↔ ↔
BAND #xx:3, @ERd
4
2
6
— — — — —
↔
B
— — — — —
¬ (#xx:3 of Rd8) → C
↔
B
BAND #xx:3, Rd
(#xx:3 of @aa:8) → C
↔
BIST #xx:3, @aa:8
4
6
↔ ↔ ↔
B
Z
↔ ↔ ↔
BIST #xx:3, @ERd
4
2
H N
↔ ↔
B
I
↔
B
BIST #xx:3, Rd
4
C
— — — — —
↔ ↔ ↔
BST #xx:3, @aa:8
2
V
(#xx:3 of @ERd) → C
↔ ↔
B
Operation
↔
B
BST #xx:3, @ERd
4
Condition Code
↔ ↔
BST #xx:3, Rd
4
No. of
States*1
—
B
4
2
@@aa
B
BILD #xx:3, @aa:8
4
@(d, PC)
BILD #xx:3, @ERd
@aa
B
@–ERn/@ERn+
B
BILD #xx:3, Rd
@(d, ERn)
BLD #xx:3, @aa:8
@ERn
B
Rn
BLD #xx:3, @ERd
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
C∧ ¬ (#xx:3 of @aa:8) → C
— — — — —
C∨(#xx:3 of Rd8) → C
— — — — —
C∨(#xx:3 of @ERd24) → C
— — — — —
C∨(#xx:3 of @aa:8) → C
— — — — —
C∨ ¬ (#xx:3 of Rd8) → C
— — — — —
C∨ ¬ (#xx:3 of @ERd24) → C — — — — —
6
2
6
2
6
6
2
6
6
Appendix A Instruction Set
6. Branching instructions
—
2
BHI d:16
—
4
BLS d:8
—
2
BLS d:16
—
4
BCC d:8 (BHS d:8)
—
2
BCC d:16 (BHS d:16) —
4
BCS d:8 (BLO d:8)
—
2
BCS d:16 (BLO d:16) —
4
BNE d:8
—
2
BNE d:16
—
4
BEQ d:8
—
2
BEQ d:16
—
4
BVC d:8
—
2
BVC d:16
—
4
BVS d:8
—
2
BVS d:16
—
4
BPL d:8
—
2
BPL d:16
—
4
BMI d:8
—
2
BMI d:16
—
4
BGE d:8
—
2
BGE d:16
—
4
BLT d:8
—
2
BLT d:16
—
4
BGT d:8
—
2
BGT d:16
—
4
If condition Always
is true then
PC ←
PC+d else Never
next;
C∨Z=0
C∨Z=1
C=0
C=1
Z=0
Z=1
V=0
V=1
N=0
N=1
N⊕V = 0
N⊕V = 1
Z ∨ (N⊕V)
=0
Condition Code
I
H N
Z
V
C
Advanced
BHI d:8
Branch
Operation Condition
Normal
4
No. of
States*1
—
2
—
@@aa
—
BRN d:16 (BF d:16)
@(d, PC)
BRN d:8 (BF d:8)
@aa
4
@(d, ERn)
2
—
@ERn
—
BRA d:16 (BT d:16)
Rn
BRA d:8 (BT d:8)
#xx
Mnemonic
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
— — — — — —
4
— — — — — —
6
Rev. 3.00 Sep 14, 2005 page 719 of 910
REJ09B0258-0300
Appendix A Instruction Set
—
JMP @@aa:8
—
BSR d:8
—
BSR d:16
—
JSR @ERn
—
JSR @aa:24
—
JSR @@aa:8
—
RTS
—
Condition Code
I
H N
Z
V
C
Advanced
JMP @aa:24
Branch
Operation Condition
Normal
—
No. of
States*1
—
JMP @ERn
@@aa
4
@(d, PC)
—
@aa
BLE d:16
@(d, ERn)
2
@ERn
—
Rn
BLE d:8
#xx
Mnemonic
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
If condition Z ∨ (N⊕V) = 1 — — — — — —
is true then
— — — — — —
PC ← PC+d
else next;
4
6
— — — — — —
2
4
— — — — — —
PC ← aa:24
— — — — — —
PC ← @aa:8
2
PC → @–SP
PC ← PC+d:8
4
2
2
4
Rev. 3.00 Sep 14, 2005 page 720 of 910
REJ09B0258-0300
PC ← ERn
2
4
6
— — — — — —
8
10
— — — — — —
6
8
PC → @–SP
PC ← PC+d:16
— — — — — —
8
10
PC → @–SP
PC ← @ERn
— — — — — —
6
8
PC → @–SP
PC ← @aa:24
— — — — — —
8
10
PC → @–SP
PC ← @aa:8
— — — — — —
8
12
8
10
2 PC ← @SP+
Appendix A Instruction Set
7. System control instructions
↔
—
Transition to
powerdown state
— — — — — —
2
LDC #xx:8, CCR
B
#xx:8 → CCR
B
LDC @ERs, CCR
W
LDC @(d:16, ERs),
CCR
W
6
@(d:16, ERs) → CCR
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
↔ ↔ ↔ ↔
2
LDC Rs, CCR
LDC @(d:24, ERs),
CCR
W
10
@(d:24, ERs) → CCR
↔
↔
↔
↔
↔
↔
12
LDC @ERs+, CCR
W
@ERs → CCR
ERs32+2 → ERs32
↔
↔
↔
↔
↔
↔
8
LDC @aa:16, CCR
W
6
@aa:16 → CCR
LDC @aa:24, CCR
W
8
@aa:24 → CCR
↔ ↔
↔ ↔
↔ ↔
↔ ↔
↔ ↔
8
10
STC CCR, Rd
B
CCR → Rd8
— — — — — —
2
6
2
Rs8 → CCR
2
@ERs → CCR
4
4
Z
V
C
Normal
H N
2
6
8
↔
↔
STC CCR, @ERd
W
CCR → @ERd
— — — — — —
STC CCR, @(d:16,
ERd)
W
6
CCR → @(d:16, ERd)
— — — — — —
8
STC CCR, @(d:24,
ERd)
W
10
CCR → @(d:24, ERd)
— — — — — —
12
STC CCR, @–ERd
W
ERd32–2 → ERd32
CCR → @ERd
— — — — — —
8
STC CCR, @aa:16
W
6
CCR → @aa:16
— — — — — —
8
8
10
↔ ↔ ↔
2
I
1 — — — — — 14 16
↔
Operation
↔
—
Condition Code
Advanced
↔
SLEEP
@@aa
10
@(d, PC)
CCR ← @SP+
PC ← @SP+
@aa
—
@(d, ERn)
RTE
@ERn
2 PC → @–SP
CCR → @–SP
<vector> → PC
Rn
—
#xx
Mnemonic
TRAPA #x:2
↔ ↔
No. of
States*1
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
2
— — — — — —
2
4
CCR∧#xx:8 → CCR
ORC #xx:8, CCR
B
2
CCR∨#xx:8 → CCR
XORC #xx:8, CCR
B
2
CCR⊕#xx:8 → CCR
NOP
—
2 PC ← PC+2
↔ ↔ ↔
2
↔ ↔ ↔
CCR → @aa:24
B
↔ ↔ ↔
W
ANDC #xx:8, CCR
↔ ↔ ↔
STC CCR, @aa:24
— — — — — —
↔ ↔ ↔
4
2
2
Rev. 3.00 Sep 14, 2005 page 721 of 910
REJ09B0258-0300
Appendix A Instruction Set
8. Block transfer instructions
Operation
I
H N
Z
V
C
— — — — — —
Normal
—
@@aa
4 if R4 ≠ 0
repeat @R5 → @R6
R5+1 → R5
R6+1 → R6
R4–1 → R4
until
R4=0
else next;
@(d, PC)
—
@aa
EEPMOV. W
@(d, ERn)
— — — — — — 8+
4 if R4L ≠ 0
repeat @R5 → @R6
4n*2
R5+1 → R5
R6+1 → R6
R4L–1 → R4L
until
R4L=0
else next;
@ERn
—
Rn
EEPMOV. B
#xx
Mnemonic
Condition Code
Advanced
No. of
States*1
Operand Size
@–ERn/@ERn+
Addressing Mode and
Instruction Length (bytes)
8+
4n*2
Notes: 1. The number of states is the number of states required for execution when the
instruction and its operands are located in on-chip memory. For other cases see
section A.3, Number of States Required for Execution.
2. n is the value set in register R4L or R4.
(1) Set to 1 when a carry or borrow occurs at bit 11; otherwise cleared to 0.
(2) Set to 1 when a carry or borrow occurs at bit 27; otherwise cleared to 0.
(3) Retains its previous value when the result is zero; otherwise cleared to 0.
(4) Set to 1 when the adjustment produces a carry; otherwise retains its previous value.
(5) The number of states required for execution of an instruction that transfers data in
synchronization with the E clock is variable.
(6) Set to 1 when the divisor is negative; otherwise cleared to 0.
(7) Set to 1 when the divisor is zero; otherwise cleared to 0.
(8) Set to 1 when the quotient is negative; otherwise cleared to 0.
Rev. 3.00 Sep 14, 2005 page 722 of 910
REJ09B0258-0300
MULXU
5
STC
Table A.2
(2)
LDC
3
SUBX
OR
XOR
AND
MOV
C
D
E
F
BILD
BIST
BLD
BST
TRAPA
BNQ
B
BIAND
BAND
AND
RTE
BNE
CMP
BIXOR
BXOR
XOR
BSR
BCS
A
BIOR
BOR
OR
RTS
BCC
MOV.B
Table A.2
(2)
LDC
7
ADDX
BTST
DIVXU
BLS
AND.B
ANDC
6
9
BCLR
MULXU
BHI
XOR.B
XORC
5
ADD
BNOT
DIVXU
BRN
OR.B
ORC
4
8
7
BSET
BRA
6
2
1
Table A.2 Table A.2 Table A.2 Table A.2
(2)
(2)
(2)
(2)
NOP
4
3
2
1
0
0
MOV
BVS
9
B
JMP
BPL
BMI
MOV
Table A.2 Table A.2
(2)
(2)
Table A.2 Table A.2
(2)
(2)
A
Table A.2 Table A.2
EEPMOV
(2)
(2)
SUB
ADD
Table A.2
(2)
BVC
8
BSR
BGE
C
CMP
MOV
Instruction when most significant bit of BH is 1.
Instruction when most significant bit of BH is 0.
E
JSR
BGT
SUBX
ADDX
Table A.2
(3)
BLT
D
BLE
Table A.2
(2)
Table A.2
(2)
F
Table A.2
AL
1st byte 2nd byte
AH AL BH BL
A.2
AH
Instruction code:
Appendix A Instruction Set
Operation Code Maps
Operation Code Map (1)
Rev. 3.00 Sep 14, 2005 page 723 of 910
REJ09B0258-0300
Rev. 3.00 Sep 14, 2005 page 724 of 910
REJ09B0258-0300
SUBS
DAS
BRA
MOV
MOV
1B
1F
58
79
7A
1
ADD
ADD
BRN
NOT
17
DEC
ROTXR
13
1A
ROTXL
12
DAA
0F
SHLR
ADDS
0B
11
INC
0A
SHLL
MOV
01
10
0
CMP
CMP
BHI
2
SUB
SUB
BLS
NOT
ROTXR
ROTXL
SHLR
SHLL
3
4
OR
OR
BCC
LDC/STC
1st byte 2nd byte
AH AL BH BL
XOR
XOR
BCS
DEC
EXTU
INC
5
AND
AND
BNE
6
BEQ
DEC
EXTU
INC
7
BVC
SUBS
NEG
9
BVS
ROTR
ROTL
SHAR
SHAL
ADDS
SLEEP
8
BPL
A
MOV
BMI
NEG
CMP
SUB
ROTR
ROTL
SHAR
C
D
BGE
BLT
DEC
EXTS
INC
Table A.2 Table A.2
(3)
(3)
ADD
SHAL
B
BGT
E
BLE
DEC
EXTS
INC
Table A.2
(3)
F
Table A.2
BH
AH AL
Instruction code:
Appendix A Instruction Set
Operation Code Map (2)
DIVXS
3
BSET
7Faa7 *2
BNOT
BNOT
BCLR
BCLR
Notes: 1. r is the register designation field.
2. aa is the absolute address field.
BSET
7Faa6 *2
BTST
BCLR
7Eaa7 *2
BNOT
BTST
BSET
7Eaa6 *2
7Dr07 *1
7Dr06 *1
BTST
BCLR
MULXS
2
7Cr07 *1
BNOT
DIVIXS
1
BTST
BSET
MULXS
0
7Cr06 *1
01F06
01D05
01C05
01406
CL
BIOR
BOR
BIOR
BOR
OR
4
BIXOR
BXOR
BIXOR
BXOR
XOR
5
BIAND
BAND
BIAND
BAND
AND
6
7
BIST
BILD
BST
BLD
BIST
BILD
BST
BLD
1st byte 2nd byte 3rd byte 4th byte
AH AL BH BL CH CL DH DL
8
LDC
STC
9
A
LDC
STC
B
C
LDC
STC
D
E
LDC
STC
F
Instruction when most significant bit of DH is 1.
Instruction when most significant bit of DH is 0.
Table A.2
AH
ALBH
BLCH
Instruction code:
Appendix A Instruction Set
Operation Code Map (3)
Rev. 3.00 Sep 14, 2005 page 725 of 910
REJ09B0258-0300
Appendix A Instruction Set
A.3
Number of States Required for Execution
The tables in this section can be used to calculate the number of states required for instruction
execution by the H8/300H CPU. Table A.4 indicates the number of instruction fetch, data
read/write, and other cycles occurring in each instruction. Table A.3 indicates the number of
states required per cycle according to the bus size. The number of states required for execution of
an instruction can be calculated from these two tables as follows:
Number of states = I × SI + J × SJ + K × SK + L × SL + M × SM + N × SN
Examples of Calculation of Number of States Required for Execution
Examples: Advanced mode, stack located in external address space, on-chip supporting modules
accessed with 8-bit bus width, external devices accessed in three states with one wait state and
16-bit bus width.
BSET #0, @FFFFC7:8
From table A.4, I = L = 2 and J = K = M = N = 0
From table A.3, SI = 4 and SL = 3
Number of states = 2 × 4 + 2 × 3 = 14
JSR @@30
From table A.4, I = J = K = 2 and L = M = N = 0
From table A.3, SI = SJ = SK = 4
Number of states = 2 × 4 + 2 × 4 + 2 × 4 = 24
Rev. 3.00 Sep 14, 2005 page 726 of 910
REJ09B0258-0300
Appendix A Instruction Set
Table A.3
Number of States per Cycle
Access Conditions
External Device
On-Chip Supporting Module
Execution State
(Cycle)
Instruction fetch
On-Chip 8-Bit
Memory Bus
SI 2
6
8-Bit Bus
16-Bit Bus
16-Bit
Bus
2-State
Access
3-State
Access
2-State
Access
3-State
Access
3
4
6 + 2m
2
3+m
Branch address read SJ
Stack operation
SK
Byte data access
SL
3
2
3+m
Word data access
SM
6
4
6 + 2m
Internal operation
SN 1
Legend
m: Number of wait states inserted into external device access
Rev. 3.00 Sep 14, 2005 page 727 of 910
REJ09B0258-0300
Appendix A Instruction Set
Table A.4
Number of Cycles per Instruction
Instruction Mnemonic
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
ADD
ADD.B #xx:8, Rd
ADD.B Rs, Rd
ADD.W #xx:16, Rd
ADD.W Rs, Rd
ADD.L #xx:32, ERd
ADD.L ERs, ERd
1
1
2
1
3
1
ADDS
ADDS #1/2/4, ERd
1
ADDX
ADDX #xx:8, Rd
ADDX Rs, Rd
1
1
AND
AND.B #xx:8, Rd
AND.B Rs, Rd
AND.W #xx:16, Rd
AND.W Rs, Rd
AND.L #xx:32, ERd
AND.L ERs, ERd
1
1
2
1
3
2
ANDC
ANDC #xx:8, CCR
1
BAND
BAND #xx:3, Rd
BAND #xx:3, @ERd
BAND #xx:3, @aa:8
1
2
2
BRA d:8 (BT d:8)
BRN d:8 (BF d:8)
BHI d:8
BLS d:8
BCC d:8 (BHS d:8)
BCS d:8 (BLO d:8)
BNE d:8
BEQ d:8
BVC d:8
BVS d:8
BPL d:8
BMI d:8
BGE d:8
BLT d:8
BGT d:8
BLE d:8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Bcc
Rev. 3.00 Sep 14, 2005 page 728 of 910
REJ09B0258-0300
1
1
Appendix A Instruction Set
Instruction Mnemonic
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Bcc
BRA d:16 (BT d:16)
BRN d:16 (BF d:16)
BHI d:16
BLS d:16
BCC d:16 (BHS d:16)
BCS d:16 (BLO d:16)
BNE d:16
BEQ d:16
BVC d:16
BVS d:16
BPL d:16
BMI d:16
BGE d:16
BLT d:16
BGT d:16
BLE d:16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
BCLR
BCLR #xx:3, Rd
BCLR #xx:3, @ERd
BCLR #xx:3, @aa:8
BCLR Rn, Rd
BCLR Rn, @ERd
BCLR Rn, @aa:8
1
2
2
1
2
2
BIAND #xx:3, Rd
BIAND #xx:3, @ERd
BIAND #xx:3, @aa:8
1
2
2
1
1
BILD #xx:3, Rd
BILD #xx:3, @ERd
BILD #xx:3, @aa:8
1
2
2
1
1
BIOR #xx:8, Rd
BIOR #xx:8, @ERd
BIOR #xx:8, @aa:8
1
2
2
1
1
BIST #xx:3, Rd
BIST #xx:3, @ERd
BIST #xx:3, @aa:8
1
2
2
2
2
BIXOR #xx:3, Rd
BIXOR #xx:3, @ERd
BIXOR #xx:3, @aa:8
1
2
2
1
1
BLD #xx:3, Rd
BLD #xx:3, @ERd
BLD #xx:3, @aa:8
1
2
2
1
1
BIAND
BILD
BIOR
BIST
BIXOR
BLD
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Rev. 3.00 Sep 14, 2005 page 729 of 910
REJ09B0258-0300
Appendix A Instruction Set
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
BNOT
BOR
BSET
BSR
BNOT #xx:3, Rd
BNOT #xx:3, @ERd
BNOT #xx:3, @aa:8
BNOT Rn, Rd
BNOT Rn, @ERd
BNOT Rn, @aa:8
1
2
2
1
2
2
BOR #xx:3, Rd
BOR #xx:3, @ERd
BOR #xx:3, @aa:8
1
2
2
BSET #xx:3, Rd
BSET #xx:3, @ERd
BSET #xx:3, @aa:8
BSET Rn, Rd
BSET Rn, @ERd
BSET Rn, @aa:8
1
2
2
1
2
2
BSR d:8
2
1
Advanced 2
2
Normal
2
1
2
Advanced 2
2
2
BSR d:16
BST
Normal
BST #xx:3, Rd
BST #xx:3, @ERd
BST #xx:3, @aa:8
1
2
2
BTST #xx:3, Rd
BTST #xx:3, @ERd
BTST #xx:3, @aa:8
BTST Rn, Rd
BTST Rn, @ERd
BTST Rn, @aa:8
1
2
2
1
2
2
BXOR #xx:3, Rd
BXOR #xx:3, @ERd
BXOR #xx:3, @aa:8
1
2
2
CMP
CMP.B #xx:8, Rd
CMP.B Rs, Rd
CMP.W #xx:16, Rd
CMP.W Rs, Rd
CMP.L #xx:32, ERd
CMP.L ERs, ERd
1
1
2
1
3
1
DAA
DAA Rd
1
DAS
DAS Rd
1
BTST
BXOR
Rev. 3.00 Sep 14, 2005 page 730 of 910
REJ09B0258-0300
2
2
2
2
1
1
2
2
2
2
2
2
1
1
1
1
1
1
Appendix A Instruction Set
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
DEC
DEC.B Rd
DEC.W #1/2, Rd
DEC.L #1/2, ERd
1
1
1
DIVXS
DIVXS.B Rs, Rd
DIVXS.W Rs, ERd
2
2
12
20
DIVXU
DIVXU.B Rs, Rd
DIVXU.W Rs, ERd
1
1
12
20
EEPMOV
EEPMOV.B
EEPMOV.W
2
2
EXTS
EXTS.W Rd
EXTS.L ERd
1
1
EXTU
EXTU.W Rd
EXTU.L ERd
1
1
INC
INC.B Rd
INC.W #1/2, Rd
INC.L #1/2, ERd
1
1
1
JMP
JMP @ERn
2
JMP @aa:24
2
JMP @@aa:8 Normal
JSR
JSR @ERn
2
2
1
2
Advanced 2
2
2
Normal
2
1
Advanced 2
2
JSR @aa:24 Normal
2
1
2
Advanced 2
2
2
JSR @@aa:8 Normal
LDC
2n + 2*1
2n + 2*1
2
1
1
Advanced 2
2
2
LDC #xx:8, CCR
LDC Rs, CCR
LDC @ERs, CCR
LDC @(d:16, ERs), CCR
LDC @(d:24, ERs), CCR
LDC @ERs+, CCR
LDC @aa:16, CCR
LDC @aa:24, CCR
1
1
2
3
5
2
3
4
1
1
1
1
1
1
2
Rev. 3.00 Sep 14, 2005 page 731 of 910
REJ09B0258-0300
Appendix A Instruction Set
Instruction Mnemonic
MOV
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
MOV.B #xx:8, Rd
MOV.B Rs, Rd
MOV.B @ERs, Rd
MOV.B @(d:16, ERs), Rd
MOV.B @(d:24, ERs), Rd
MOV.B @ERs+, Rd
MOV.B @aa:8, Rd
MOV.B @aa:16, Rd
MOV.B @aa:24, Rd
MOV.B Rs, @ERd
MOV.B Rs, @(d:16, ERd)
MOV.B Rs, @(d:24, ERd)
MOV.B Rs, @–ERd
MOV.B Rs, @aa:8
MOV.B Rs, @aa:16
MOV.B Rs, @aa:24
MOV.W #xx:16, Rd
MOV.W Rs, Rd
MOV.W @ERs, Rd
MOV.W @(d:16, ERs), Rd
MOV.W @(d:24, ERs), Rd
MOV.W @ERs+, Rd
MOV.W @aa:16, Rd
MOV.W @aa:24, Rd
MOV.W Rs, @ERd
MOV.W Rs, @(d:16, ERd)
MOV.W Rs, @(d:24, ERd)
MOV.W Rs, @–ERd
MOV.W Rs, @aa:16
MOV.W Rs, @aa:24
1
1
1
2
4
1
1
2
3
1
2
4
1
1
2
3
2
1
1
2
4
1
2
3
1
2
4
1
2
3
MOV.L #xx:32, ERd
MOV.L ERs, ERd
MOV.L @ERs, ERd
MOV.L @(d:16, ERs), ERd
MOV.L @(d:24, ERs), ERd
MOV.L @ERs+, ERd
MOV.L @aa:16, ERd
MOV.L @aa:24, ERd
MOV.L ERs, @ERd
MOV.L ERs, @(d:16, ERd)
MOV.L ERs, @(d:24, ERd)
MOV.L ERs, @–ERd
MOV.L ERs, @aa:16
MOV.L ERs, @aa:24
3
1
2
3
5
2
3
4
2
3
5
2
3
4
Rev. 3.00 Sep 14, 2005 page 732 of 910
REJ09B0258-0300
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Appendix A Instruction Set
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
MOVFPE
2
MOVFPE @aa:16, Rd* 2
1
2
MOVTPE
MOVTPE Rs, @aa:16* 2
MULXS
MULXS.B Rs, Rd
MULXS.W Rs, ERd
2
2
1
12
20
MULXU
MULXU.B Rs, Rd
MULXU.W Rs, ERd
1
1
12
20
NEG
NEG.B Rd
NEG.W Rd
NEG.L ERd
1
1
1
NOP
NOP
1
NOT
NOT.B Rd
NOT.W Rd
NOT.L ERd
1
1
1
OR
OR.B #xx:8, Rd
OR.B Rs, Rd
OR.W #xx:16, Rd
OR.W Rs, Rd
OR.L #xx:32, ERd
OR.L ERs, ERd
1
1
2
1
3
2
ORC
ORC #xx:8, CCR
1
POP
POP.W Rn
POP.L ERn
1
2
1
2
2
2
PUSH
PUSH.W Rn
PUSH.L ERn
1
2
1
2
2
2
ROTL
ROTL.B Rd
ROTL.W Rd
ROTL.L ERd
1
1
1
ROTR
ROTR.B Rd
ROTR.W Rd
ROTR.L ERd
1
1
1
ROTXL
ROTXL.B Rd
ROTXL.W Rd
ROTXL.L ERd
1
1
1
ROTXR
ROTXR.B Rd
ROTXR.W Rd
ROTXR.L ERd
1
1
1
RTE
RTE
2
2
2
Rev. 3.00 Sep 14, 2005 page 733 of 910
REJ09B0258-0300
Appendix A Instruction Set
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
RTS
RTS
2
1
2
Advanced 2
Normal
2
2
SHAL
SHAL.B Rd
SHAL.W Rd
SHAL.L ERd
1
1
1
SHAR
SHAR.B Rd
SHAR.W Rd
SHAR.L ERd
1
1
1
SHLL
SHLL.B Rd
SHLL.W Rd
SHLL.L ERd
1
1
1
SHLR
SHLR.B Rd
SHLR.W Rd
SHLR.L ERd
1
1
1
SLEEP
SLEEP
1
STC
STC CCR, Rd
STC CCR, @ERd
STC CCR, @(d:16, ERd)
STC CCR, @(d:24, ERd)
STC CCR, @–ERd
STC CCR, @aa:16
STC CCR, @aa:24
1
2
3
5
2
3
4
SUB
SUB.B Rs, Rd
SUB.W #xx:16, Rd
SUB.W Rs, Rd
SUB.L #xx:32, ERd
SUB.L ERs, ERd
1
2
1
3
1
SUBS
SUBS #1/2/4, ERd
1
SUBX
SUBX #xx:8, Rd
SUBX Rs, Rd
1
1
TRAPA
TRAPA #x:2
2
1
2
4
Advanced 2
2
2
4
Normal
XOR
XOR.B #xx:8, Rd
XOR.B Rs, Rd
XOR.W #xx:16, Rd
XOR.W Rs, Rd
XOR.L #xx:32, ERd
XOR.L ERs, ERd
1
1
2
1
3
2
XORC
XORC #xx:8, CCR
1
1
1
1
1
1
1
2
Notes: 1. n is the value set in register R4L or R4. The source and destination are accessed n + 1
times each.
2. Not available in the H8/3067 Group.
Rev. 3.00 Sep 14, 2005 page 734 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Appendix B Internal I/O Registers
B.1 Addresses (EMC = 1)
Address
(Low)
Data
Register Bus
Width Bit 7
Name
H'EE000
P1DDR
8
H'EE001
P2DDR
8
H'EE002
P3DDR
H'EE003
P4DDR
H'EE004
Bit Names
Bit 1
Bit 0
Module
Name
P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR
P11DDR
P10DDR
Port 1
P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR
P21DDR
P20DDR
Port 2
8
P37DDR P36DDR P35DDR P34DDR P33DDR P32DDR
P31DDR
P30DDR
Port 3
8
P47DDR P46DDR P45DDR P44DDR P43DDR P42DDR
P41DDR
P40DDR
Port 4
P5DDR
8
—
—
P53DDR P52DDR
P51DDR
P50DDR
Port 5
H'EE005
P6DDR
8
—
P66DDR P65DDR P64DDR P63DDR P62DDR
P61DDR
P60DDR
Port 6
H'EE006
—
—
—
—
—
—
—
H'EE007
P8DDR
8
—
—
—
P84DDR P83DDR P82DDR
P81DDR
P80DDR
Port 8
H'EE008
P9DDR
8
—
—
P95DDR P94DDR P93DDR P92DDR
P91DDR
P90DDR
Port 9
H'EE009
PADDR
8
PA7DDR PA6DDR PA5DDR PA4DDR PA3DDR PA2DDR PA1DDR PA0DDR Port A
H'EE00A
PBDDR
8
PB7DDR PB6DDR PB5DDR PB4DDR PB3DDR PB2DDR PB1DDR PB0DDR Port B
H'EE00B
—
—
—
—
—
—
—
—
—
H'EE00C
—
—
—
—
—
—
—
—
—
H'EE00D
—
—
—
—
—
—
—
—
—
H'EE00E
—
—
—
—
—
—
—
—
—
H'EE00F
—
—
—
—
—
—
—
—
—
H'EE010
—
—
—
—
—
—
—
—
—
H'EE011
MDCR
8
—
—
—
—
—
MDS2
MDS1
MDS0
H'EE012
SYSCR
8
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
H'EE013
BRCR
8
A23E
A22E
A21E
A20E
—
—
—
BRLE
Bus controller
H'EE014
ISCR
8
—
—
IRQ5SC IRQ4SC IRQ3SC IRQ2SC
IRQ1SC
IRQ0SC
H'EE015
IER
8
—
—
IRQ5E
IRQ2E
IRQ1E
IRQ0E
Interrupt
controller
H'EE016
ISR
8
—
—
H'EE017
—
—
—
Bit 6
Bit 5
—
Bit 4
—
Bit 3
—
Bit 2
—
IRQ4E
IRQ3E
IRQ5F
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
—
—
—
—
—
—
H'EE018
IPRA
8
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
H'EE019
IPRB
8
IPRB7
IPRB6
IPRB5
—
IPRB3
IPRB2
IPRB1
—
H'EE01A
DASTCR 8
—
—
—
—
—
—
—
DASTE
H'EE01B
DIVCR
—
—
—
—
—
—
DIV1
DIV0
H'EE01C
MSTCRH 8
PSTOP
—
—
—
—
8
System
control
D/A converter
System
MSTPH2 MSTPH1 MSTPH0 control
H'EE01D
MSTCRL 8
MSTPL7 —
MSTPL5 MSTPL4 MSTPL3 MSTPL2 —
MSTPL0
H'EE01E
ADRCR
8
—
—
—
—
—
—
—
ADRCTL Bus controller
H'EE01F
CSCR
8
CS7E
CS6E
CS5E
CS4E
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 735 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
H'EE020
ABWCR
8
ABW7
ABW6
ABW5
ABW4
ABW3
ABW2
H'EE021
ASTCR
8
AST7
AST6
AST5
AST4
AST3
AST2
H'EE022
WCRH
8
W71
W70
W61
W60
W51
W50
W41
W40
H'EE023
WCRL
8
W31
W30
W21
W20
W11
W10
W01
W00
H'EE024
BCR
8
ICIS1
ICIS0
BROME BRSTS1 BRSTS0 —
RDEA
WAITE
—
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 0
Module
Name
ABW1
ABW0
Bus controller
AST1
AST0
Bit 1
H'EE025
—
—
—
—
—
—
—
—
H'EE026
DRCRA
8
DRAS2
DRAS1
DRAS0
—
BE
RDM
SRFMD
RFSHE
H'EE027
DRCRB
8
MXC1
MXC0
CSEL
RCYCE —
TPC
RCW
RLW
CMF
CMIE
CKS2
CKS1
CKS0
—
—
—
H'EE028
RTMCSR 8
H'EE029
RTCNT
8
H'EE02A
RTCOR
8
H'EE02B
Reserved area (access prohibited)
DRAM
Interface
H'EE02C
H'EE02D
H'EE02E
H'EE02F
H'EE030
FLMCR1 8
FWE
SWE
ESU
PSU
EV
PV
E
P
H'EE031
FLMCR2 8
FLER
—
—
—
—
—
—
—
H'EE032
EBR1
8
EB7
EB6
EB5
EB4
EB3
EB2
EB1
EB0
H'EE033
EBR2
8
—
—
EB13
EB12
EB11
EB10
EB9
EB8
H'EE034
Reserved area (access prohibited)
P27PCR P26PCR P25PCR P24PCR P23PCR P22PCR
P27PCR
P20PCR
—
Flash
memory
H'EE035
H'EE036
H'EE037
H'EE038
H'EE039
H'EE03A
H'EE03B
H'EE03C
P2PCR
8
H'EE03D
—
—
—
H'EE03E
P4PCR
8
P47PCR P46PCR P45PCR P44PCR P43PCR P42PCR
P41PCR
P40PCR
Port 4
H'EE03F
P5PCR
8
—
P51PCR
P50PCR
Port 5
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 736 of 910
REJ09B0258-0300
—
—
—
—
P53PCR P52PCR
Port 2
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'EE040
—
—
—
—
—
—
—
—
—
H'EE041
—
—
—
—
—
—
—
—
—
H'EE042
—
—
—
—
—
—
—
—
—
H'EE043
—
—
—
—
—
—
—
—
—
H'EE044
—
—
—
—
—
—
—
—
—
H'EE045
—
—
—
—
—
—
—
—
—
H'EE046
—
—
—
—
—
—
—
—
—
H'EE047
—
—
—
—
—
—
—
—
—
H'EE048
—
—
—
—
—
—
—
—
—
H'EE049
—
—
—
—
—
—
—
—
—
H'EE04A
—
—
—
—
—
—
—
—
—
H'EE04B
—
—
—
—
—
—
—
—
—
H'EE04C
—
—
—
—
—
—
—
—
—
H'EE04D
—
—
—
—
—
—
—
—
—
Bit Names
H'EE04E
—
—
—
—
—
—
—
—
—
H'EE04F
—
—
—
—
—
—
—
—
—
H'EE050
—
—
—
—
—
—
—
—
—
H'EE051
—
—
—
—
—
—
—
—
—
H'EE052
—
—
—
—
—
—
—
—
—
H'EE053
—
—
—
—
—
—
—
—
—
H'EE054
—
—
—
—
—
—
—
—
—
H'EE055
—
—
—
—
—
—
—
—
—
H'EE056
—
—
—
—
—
—
—
—
—
H'EE057
—
—
—
—
—
—
—
—
—
H'EE058
—
—
—
—
—
—
—
—
—
H'EE059
—
—
—
—
—
—
—
—
—
H'EE05A
—
—
—
—
—
—
—
—
—
H'EE05B
—
—
—
—
—
—
—
—
—
H'EE05C
—
—
—
—
—
—
—
—
—
H'EE05D
—
—
—
—
—
—
—
—
—
H'EE05E
—
—
—
—
—
—
—
—
—
H'EE05F
—
—
—
—
—
—
—
—
—
Module
Name
Rev. 3.00 Sep 14, 2005 page 737 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'EE060
—
—
—
—
—
—
—
—
—
H'EE061
—
—
—
—
—
—
—
—
—
H'EE062
—
—
—
—
—
—
—
—
—
H'EE063
—
—
—
—
—
—
—
—
—
H'EE064
—
—
—
—
—
—
—
—
—
H'EE065
—
—
—
—
—
—
—
—
—
H'EE066
—
—
—
—
—
—
—
—
—
H'EE067
—
—
—
—
—
—
—
—
—
H'EE068
—
—
—
—
—
—
—
—
—
H'EE069
—
—
—
—
—
—
—
—
—
H'EE06A
—
—
—
—
—
—
—
—
—
H'EE06B
—
—
—
—
—
—
—
—
—
H'EE06C
—
—
—
—
—
—
—
—
—
H'EE06D
—
—
—
—
—
—
—
—
—
Bit Names
H'EE06E
—
—
—
—
—
—
—
—
—
H'EE06F
—
—
—
—
—
—
—
—
—
H'EE070
—
—
—
—
—
—
—
—
—
H'EE071
—
—
—
—
—
—
—
—
—
H'EE072
—
—
—
—
—
—
—
—
—
H'EE073
—
—
—
—
—
—
—
—
—
H'EE074
Reserved area (access prohibited)
—
—
RAMS
RAM2
RAM1
RAM0
Module
Name
H'EE075
H'EE076
H'EE077
RAMCR
*1
8
—
—
H'EE078
Reserved area (access prohibited)
H'EE079
H'EE07A
H'EE07B
H'EE07C
H'EE07D
H'EE07E
H'EE07F
Rev. 3.00 Sep 14, 2005 page 738 of 910
REJ09B0258-0300
Flash
memory*1
Appendix B Internal I/O Registers
Data
Bus
Width Bit 7
Bit Names
Address
(Low)
Register
Name
H'EE080
Reserved area (access prohibited)
Flash memory*1
H'FFF20
MAR0AR
8
DMAC channel 0A
H'FFF21
MAR0AE
8
H'FFF22
MAR0AH
8
H'FFF23
MAR0AL
8
H'FFF24
ETCR0AH 8
H'FFF25
ETCR0AL 8
H'FFF26
IOAR0A
8
H'FFF27
DTCR0A
8
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
H'EE081
H'FFF28
MAR0BR
8
H'FFF29
MAR0BE
8
H'FFF2A
MAR0BH
8
H'FFF2B
MAR0BL
8
H'FFF2C
ETCR0BH 8
H'FFF2D
ETCR0BL 8
H'FFF2E
IOAR0B
8
H'FFF2F
DTCR0B
8
H'FFF30
MAR1AR
8
H'FFF31
MAR1AE
8
H'FFF32
MAR1AH
8
H'FFF33
MAR1AL
8
H'FFF34
ETCR1AH 8
H'FFF35
ETCR1AL 8
H'FFF36
IOAR1A
8
H'FFF37
DTCR1A
8
H'FFF38
MAR1BR
8
H'FFF39
MAR1BE
8
H'FFF3A
MAR1BH
8
H'FFF3B
MAR1BL
8
H'FFF3C
ETCR1BH 8
H'FFF3D
ETCR1BL 8
H'FFF3E
IOAR1B
8
H'FFF3F
DTCR1B
8
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A DTS1A DTS0A Full address mode
DTS1
DTS0
Short address mode
DMAC channel 0B
DTE
DTSZ
DTID
RPE
DTME
—
DAID
DAIDE TMS
DTIE
DTS2
DTS1
DTS0
Short address mode
DTS2B DTS1B DTS0B Full address mode
DMAC channel 1A
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A DTS1A DTS0A Full address mode
DTS1
DTS0
Short address mode
DMAC channel 1B
DTE
DTSZ
DTID
RPE
DTME
—
DAID
DAIDE TMS
DTIE
DTS2
DTS1
DTS0
Short address mode
DTS2B DTS1B DTS0B Full address mode
Rev. 3.00 Sep 14, 2005 page 739 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFF40
—
—
—
—
—
—
—
—
—
H'FFF41
—
—
—
—
—
—
—
—
—
H'FFF42
—
—
—
—
—
—
—
—
—
H'FFF43
—
—
—
—
—
—
—
—
—
H'FFF44
—
—
—
—
—
—
—
—
—
H'FFF45
—
—
—
—
—
—
—
—
—
H'FFF46
—
—
—
—
—
—
—
—
—
H'FFF47
—
—
—
—
—
—
—
—
—
H'FFF48
—
—
—
—
—
—
—
—
—
H'FFF49
—
—
—
—
—
—
—
—
—
H'FFF4A
—
—
—
—
—
—
—
—
—
H'FFF4B
—
—
—
—
—
—
—
—
—
H'FFF4C
—
—
—
—
—
—
—
—
—
H'FFF4D
—
—
—
—
—
—
—
—
—
H'FFF4E
—
—
—
—
—
—
—
—
—
H'FFF4F
—
—
—
—
—
—
—
—
—
H'FFF50
—
—
—
—
—
—
—
—
—
H'FFF51
—
—
—
—
—
—
—
—
—
H'FFF52
—
—
—
—
—
—
—
—
—
H'FFF53
—
—
—
—
—
—
—
—
—
H'FFF54
—
—
—
—
—
—
—
—
—
H'FFF55
—
—
—
—
—
—
—
—
—
H'FFF56
—
—
—
—
—
—
—
—
—
H'FFF57
—
—
—
—
—
—
—
—
—
H'FFF58
—
—
—
—
—
—
—
—
—
H'FFF59
—
—
—
—
—
—
—
—
—
H'FFF5A
—
—
—
—
—
—
—
—
—
H'FFF5B
—
—
—
—
—
—
—
—
—
H'FFF5C
—
—
—
—
—
—
—
—
—
H'FFF5D
—
—
—
—
—
—
—
—
—
H'FFF5E
—
—
—
—
—
—
—
—
—
H'FFF5F
—
—
—
—
—
—
—
—
—
Bit Names
Rev. 3.00 Sep 14, 2005 page 740 of 910
REJ09B0258-0300
Module
Name
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFF60
TSTR
8
—
—
—
—
—
STR2
STR1
STR0
H'FFF61
TSNC
8
—
—
—
—
—
SYNC2
SYNC1
SYNC0
H'FFF62
TMDR
8
—
MDF
FDIR
—
—
PWM2
PWM1
PWM0
H'FFF63
TOLR
8
—
—
TOB2
TOA2
TOB1
TOA1
TOB0
TOA0
H'FFF64
TISRA
8
—
IMIEA2
IMIEA1
IMIEA0
—
IMFA2
IMFA1
IMFA0
H'FFF65
TISRB
8
—
IMIEB2
IMIEB1
IMIEB0
—
IMFB2
IMFB1
IMFB0
H'FFF66
TISRC
8
—
OVIE2
OVIE1
OVIE0
—
OVF2
OVF1
OVF0
H'FFF68
TCR0
8
—
CCLR1
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
H'FFF69
TIOR0
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'FFF6A
TCNT0H 16
H'FFF6B
TCNT0L
Module
Name
16-bit timer,
(all channels)
H'FFF67
H'FFF6C
GRA0H
H'FFF6D
GRA0L
16
H'FFF6E
GRB0H
H'FFF6F
GRB0L
H'FFF70
TCR1
8
—
CCLR1
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
H'FFF71
TIOR1
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'FFF72
TCNT1H 16
H'FFF73
TCNT1L
H'FFF74
GRA1H
H'FFF75
GRA1L
16
GRB1H
H'FFF77
GRB1L
H'FFF78
TCR2
8
—
CCLR1
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
H'FFF79
TIOR2
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'FFF7A
TCNT2H 16
H'FFF7B
TCNT2L
H'FFF7C
GRA2H
H'FFF7D
GRA2L
GRB2H
H'FFF7F
GRB2L
16-bit timer
channel 1
16
H'FFF76
H'FFF7E
16-bit timer
channel 0
16
16-bit timer
channel 2
16
16
Rev. 3.00 Sep 14, 2005 page 741 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFF80 TCR0
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFF81 TCR1
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFF82 TCSR0
8
CMFB
CMFA
OVF
ADTE
OIS3
OIS2
OS1
OS0
H'FFF83 TCSR1
8
CMFB
CMFA
OVF
ICE
OIS3
OIS2
OS1
OS0
H'FFF84 TCORA0
8
H'FFF85 TCORA1
8
H'FFF86 TCORB0
8
H'FFF8A —
—
—
—
—
—
—
—
—
H'FFF8B —
—
—
—
—
—
—
—
—
OVF
WT/IT
TME
—
—
CKS2
CKS1
CKS0
—
—
—
—
—
—
—
—
H'FFF87 TCORB1
8
H'FFF88 TCNT0
8
H'FFF89 TCNT1
8
H'FFF8C TCSR*2
8
H'FFF8D TCNT*2
8
H'FFF8E —
H'FFF8F RSTCSR
*2
8
WRST
RSTOE
—
—
—
—
—
—
H'FFF90 TCR2
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFF91 TCR3
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFF92 TCSR2
8
CMFB
CMFA
OVF
—
OIS3
OIS2
OS1
OS0
H'FFF93 TCSR3
8
CMFB
CMFA
OVF
ICE
OIS3
OIS2
OS1
OS0
H'FFF94 TCORA2
8
H'FFF95 TCORA3
8
H'FFF96 TCORB2
8
H'FFF9A —
—
—
—
—
—
—
—
—
H'FFF9B —
—
—
—
—
—
—
—
—
H'FFF97 TCORB3
8
H'FFF98 TCNT2
8
H'FFF99 TCNT3
8
H'FFF9C DADR0
8
H'FFF9D DADR1
8
H'FFF9E DACR
8
DAOE1
DAOE0
DAE
—
—
—
—
—
H'FFF9F —
8
—
—
—
—
—
—
—
—
Module
Name
8-bit timer
channels 0
and 1
WDT
8-bit timer
channels 2
and 3
D/A converter
Rev. 3.00 Sep 14, 2005 page 742 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Data
Address Register Bus
Width Bit 7
(Low)
Name
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
H'FFFA0 TPMR
8
—
—
—
—
G3NOV
G2NOV
G1NOV
G0NOV
TPC
H'FFFA1 TPCR
8
G3CMS1 G3CMS0 G2CMS1 G2CMS0 G1CMS1 G1CMS0 G0CMS1 G0CMS0
Bit Names
H'FFFA2 NDERB
8
NDER15 NDER14 NDER13 NDER12 NDER11 NDER10 NDER9
NDER8
H'FFFA3 NDERA
8
NDER7
NDER1
NDER0
NDER15 NDER14 NDER13 NDER12 NDER11 NDER10 NDER9
NDER8
H'FFFA4 NDRB*3 8
H'FFFA5 NDRA*3 8
H'FFFA6 NDRB*3 8
H'FFFA7 NDRA*3 8
NDER6
NDER5
NDER4
NDER3
NDER2
NDER15 NDER14 NDER13 NDER12 —
—
—
—
NDER7
NDER6
NDER5
NDER4
NDER3
NDER2
NDER1
NDER0
NDER7
NDER6
NDER5
NDER4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NDER11 NDER10 NDER9
—
NDER8
—
—
—
—
—
—
—
—
—
—
—
—
NDER3
NDER2
NDER1
NDER0
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
TDRE
RDRF
ORER
FER/ERS PER
TEND
MPB
MPBT
—
—
—
—
SDIR
SINV
—
SMIF
H'FFFA8
H'FFFA9
H'FFFAA
H'FFFAB
H'FFFAC
H'FFFAD
H'FFFAE
H'FFFAF
H'FFFB0 SMR
8
H'FFFB1 BRR
8
H'FFFB2 SCR
8
H'FFFB3 TDR
8
H'FFFB4 SSR
8
H'FFFB5 RDR
8
H'FFFB6 SCMR
8
SCI
channel 0
H'FFFB7 Reserved area (access prohibited)
H'FFFB8 SMR
8
H'FFFB9 BRR
8
H'FFFBA SCR
8
H'FFFBB TDR
8
H'FFFBC SSR
8
H'FFFBD RDR
8
H'FFFBE SCMR
8
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
TDRE
RDRF
ORER
FER/ERS PER
TEND
MPB
MPBT
—
—
—
—
SINV
—
SMIF
SDIR
SCI
channel 1
H'FFFBF Reserved area (access prohibited)
Rev. 3.00 Sep 14, 2005 page 743 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFFC0
SMR
8
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
H'FFFC1
BRR
8
H'FFFC2
SCR
8
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
H'FFFC3
TDR
8
H'FFFC4
SSR
8
TDRE
RDRF
ORER
FER/ERS PER
TEND
MPB
MPBT
—
—
—
—
SDIR
SINV
—
SMIF
—
Bit Names
Module
Name
SCI
channel 2
H'FFFC5
RDR
8
H'FFFC6
SCMR
8
H'FFFC7
Reserved area (access prohibited)
H'FFFC8
—
—
—
—
—
—
—
—
H'FFFC9
—
—
—
—
—
—
—
—
—
H'FFFCA
—
—
—
—
—
—
—
—
—
H'FFFCB
—
—
—
—
—
—
—
—
—
H'FFFCC
—
—
—
—
—
—
—
—
—
H'FFFCD
—
—
—
—
—
—
—
—
—
H'FFFCE
—
—
—
—
—
—
—
—
—
H'FFFCF
—
—
—
—
—
—
—
—
—
H'FFFD0
P1DR
8
P17
P16
P15
P14
P13
P12
P11
P10
Port1
H'FFFD1
P2DR
8
P27
P26
P25
P24
P23
P22
P21
P20
Port2
H'FFFD2
P3DR
8
P37
P36
P35
P34
P33
P32
P31
P30
Port3
H'FFFD3
P4DR
8
P47
P46
P45
P44
P43
P42
P41
P40
Port4
H'FFFD4
P5DR
8
—
—
—
—
P53
P52
P51
P50
Port5
H'FFFD5
P6DR
8
P67
P66
P65
P64
P63
P62
P61
P60
Port6
H'FFFD6
P7DR
8
P77
P76
P75
P74
P73
P72
P71
P70
Port7
H'FFFD7
P8DR
8
—
—
—
P84
P83
P82
P81
P80
Port8
H'FFFD8
P9DR
8
—
—
P95
P94
P93
P92
P91
P90
Port9
H'FFFD9
PADR
8
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
PortA
H'FFFDA
PBDR
8
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
PortB
H'FFFDB
—
—
—
—
—
—
—
—
—
H'FFFDC
—
—
—
—
—
—
—
—
—
H'FFFDD
—
—
—
—
—
—
—
—
—
H'FFFDE
—
—
—
—
—
—
—
—
—
H'FFFDF
—
—
—
—
—
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 744 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address
(Low)
Data
Register Bus
Width Bit 7
Name
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
H'FFFE0
ADDRAH 8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
A/D converter
H'FFFE1
ADDRAL 8
AD1
AD0
—
—
—
—
—
—
H'FFFE2
ADDRBH 8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'FFFE3
ADDRBL 8
AD1
AD0
—
—
—
—
—
—
H'FFFE4
ADDRCH 8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
Bit Names
H'FFFE5
ADDRCL 8
AD1
AD0
—
—
—
—
—
—
H'FFFE6
ADDRDH 8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'FFFE7
ADDRDL 8
AD1
AD0
—
—
—
—
—
—
H'FFFE8
ADCSR
8
ADF
ADIE
ADST
SCAN
CKS
CH2
CH1
CH0
H'FFFE9
ADCR
8
TRGE
—
—
—
—
—
—
—
Notes: 1. The RAMCR and FLMCR registers are used only in the flash memory and flash
memory R versions, and are not provided in the mask ROM versions.
2. For write access to TCSR, TCNT, and RSTCSR, see section 12.2.4, Notes on Register
Access.
3. The address depends on the output trigger setting.
Legend
WDT: Watchdog timer
TPC: Programmable timing pattern controller
SCI: Serial communication interface
Rev. 3.00 Sep 14, 2005 page 745 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
B.2 Addresses (EMC = 0)
Address Register
(Low)
Name
Data
Bus
Width Bit 7
H'EE000
P1DDR
8
H'EE001
P2DDR
8
H'EE002
P3DDR
H'EE003
Bit Names
Bit 1
Bit 0
Module
Name
P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR
P11DDR
P10DDR
Port 1
P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR
P21DDR
P20DDR
Port 2
8
P37DDR P36DDR P35DDR P34DDR P33DDR P32DDR
P31DDR
P30DDR
Port 3
P4DDR
8
P47DDR P46DDR P45DDR P44DDR P43DDR P42DDR
P41DDR
P40DDR
Port 4
H'EE004
P5DDR
8
—
—
P53DDR P52DDR
P51DDR
P50DDR
Port 5
H'EE005
P6DDR
8
—
P66DDR P65DDR P64DDR P63DDR P62DDR
P61DDR
P60DDR
Port 6
H'EE006
—
—
—
—
—
—
—
—
H'EE007
P8DDR
8
—
—
—
P84DDR P83DDR P82DDR
P81DDR
P80DDR
Port 8
H'EE008
P9DDR
8
—
—
P95DDR P94DDR P93DDR P92DDR
P91DDR
P90DDR
Port 9
H'EE009
PADDR
8
PA7DDR PA6DDR PA5DDR PA4DDR PA3DDR PA2DDR PA1DDR PA0DDR Port A
H'EE00A PBDDR
8
PB7DDR PB6DDR PB5DDR PB4DDR PB3DDR PB2DDR PB1DDR PB0DDR Port B
Bit 6
Bit 5
—
Bit 4
—
Bit 3
—
Bit 2
—
H'EE00B —
—
—
—
—
—
—
—
—
H'EE00C —
—
—
—
—
—
—
—
—
H'EE00D —
—
—
—
—
—
—
—
—
H'EE00E —
—
—
—
—
—
—
—
—
H'EE00F
—
—
—
—
—
—
—
—
—
H'EE010
—
—
—
—
—
—
—
—
—
H'EE011
MDCR
8
—
—
—
—
—
MDS2
MDS1
MDS0
H'EE012
SYSCR
8
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
H'EE013
BRCR
8
A23E
A22E
A21E
A20E
—
—
—
BRLE
Bus
controller
Interrupt
controller
H'EE014
ISCR
8
—
—
IRQ5SC IRQ4SC IRQ3SC IRQ2SC
IRQ1SC
IRQ0SC
H'EE015
IER
8
—
—
IRQ5E
IRQ2E
IRQ1E
IRQ0E
H'EE016
ISR
8
—
—
H'EE017
—
8
—
—
IRQ4E
IRQ3E
IRQ5F
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
—
—
—
—
—
—
H'EE018
IPRA
8
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
H'EE019
IPRB
8
IPRB7
IPRB6
IPRB5
—
IPRB3
IPRB2
IPRB1
—
H'EE01A DASTCR
8
—
—
—
—
—
—
—
DASTE
H'EE01B DIVCR
8
—
—
—
—
—
—
H'EE01C MSTCRH
8
PSTOP
—
—
—
—
System
control
D/A
converter
DIV1
DIV0
System
MSTPH2 MSTPH1 MSTPH0 control
H'EE01D MSTCRL
8
MSTPL7 —
MSTPL5 MSTPL4 MSTPL3 MSTPL2 —
MSTPL0
H'EE01E ADRCR
8
—
—
—
—
—
—
—
ADRCTL Bus
controller
H'EE01F
8
CS7E
CS6E
CS5E
CS4E
—
—
—
—
CSCR
Rev. 3.00 Sep 14, 2005 page 746 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'EE020
ABWCR
8
ABW7
ABW6
ABW5
ABW4
ABW3
ABW2
ABW1
ABW0
H'EE021
ASTCR
8
AST7
AST6
AST5
AST4
AST3
AST2
AST1
AST0
H'EE022
WCRH
8
W71
W70
W61
W60
W51
W50
W41
W40
H'EE023
WCRL
8
W31
W30
W21
W20
W11
W10
W01
W00
H'EE024
BCR
8
ICIS1
ICIS0
BROME BRSTS1 BRSTS0 EMC
RDEA
WAITE
H'EE025
(FLWCR)
—
—
—
—
—
—
—
BE
—
H'EE026
DRCRA
8
DRAS2
DRAS1
DRAS0
—
RDM
SRFMD
RFSHE
H'EE027
DRCRB
8
MXC1
MXC0
CSEL
RCYCE —
TPC
RCW
RLW
CMF
CMIE
CKS2
CKS1
—
—
—
H'EE028
RTMCSR
8
H'EE029
RTCNT
8
H'EE02A RTCOR
8
H'EE02B —
8
H'EE02C DCR0
8
H'EE02D DCR1
8
H'EE02E DCR2
8
H'EE02F
DCR3
8
H'EE030
FLMCR1
8
FWE
H'EE031
FLMCR2
8
FLER
H'EE032
EBR1
8
H'EE033
EBR2
8
H'EE034
Reserved area (access prohibited)
CKS0
Module
Name
Bus
controller
DRAM
interface
Bus
controller
SWE
ESU
PSU
EV
PV
E
P
EB7
EB6
EB5
EB4
EB3
EB2
EB1
EB0
—
—
EB13
EB12
EB11
EB10
EB9
EB8
P27PCR
P20PCR
Flash
memory
H'EE035
H'EE036
H'EE037
H'EE03C P2PCR
8
P27PCR P26PCR P25PCR P24PCR P23PCR P22PCR
H'EE03D —
8
—
—
—
H'EE03E P4PCR
8
P47PCR P46PCR P45PCR P44PCR P43PCR P42PCR
P41PCR
P40PCR
Port 4
H'EE03F
8
—
P51PCR
P50PCR
Port 5
P5PCR
—
—
—
—
—
—
—
—
P53PCR P52PCR
Port 2
Rev. 3.00 Sep 14, 2005 page 747 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'EE040
—
—
—
—
—
—
—
—
—
H'EE041
—
—
—
—
—
—
—
—
—
H'EE042
—
—
—
—
—
—
—
—
—
H'EE043
—
—
—
—
—
—
—
—
—
H'EE044
—
—
—
—
—
—
—
—
—
H'EE045
—
—
—
—
—
—
—
—
—
H'EE046
—
—
—
—
—
—
—
—
—
H'EE047
—
—
—
—
—
—
—
—
—
H'EE048
—
—
—
—
—
—
—
—
—
H'EE049
—
—
—
—
—
—
—
—
—
H'EE04A —
—
—
—
—
—
—
—
—
H'EE04B —
—
—
—
—
—
—
—
—
H'EE04C —
—
—
—
—
—
—
—
—
H'EE04D —
—
—
—
—
—
—
—
—
H'EE04E —
—
—
—
—
—
—
—
—
H'EE04F
—
—
—
—
—
—
—
—
—
H'EE050
—
—
—
—
—
—
—
—
—
H'EE051
—
—
—
—
—
—
—
—
—
H'EE052
—
—
—
—
—
—
—
—
—
H'EE053
—
—
—
—
—
—
—
—
—
H'EE054
—
—
—
—
—
—
—
—
—
H'EE055
—
—
—
—
—
—
—
—
—
H'EE056
—
—
—
—
—
—
—
—
—
H'EE057
—
—
—
—
—
—
—
—
—
H'EE058
—
—
—
—
—
—
—
—
—
H'EE059
—
—
—
—
—
—
—
—
—
H'EE05A —
—
—
—
—
—
—
—
—
H'EE05B —
—
—
—
—
—
—
—
—
H'EE05C —
—
—
—
—
—
—
—
—
H'EE05D —
—
—
—
—
—
—
—
—
H'EE05E —
—
—
—
—
—
—
—
—
H'EE05F
—
—
—
—
—
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 748 of 910
REJ09B0258-0300
Module
Name
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'EE060
—
—
—
—
—
—
—
—
—
H'EE061
—
—
—
—
—
—
—
—
—
H'EE062
—
—
—
—
—
—
—
—
—
H'EE063
—
—
—
—
—
—
—
—
—
H'EE064
—
—
—
—
—
—
—
—
—
H'EE065
—
—
—
—
—
—
—
—
—
H'EE066
—
—
—
—
—
—
—
—
—
H'EE067
—
—
—
—
—
—
—
—
—
H'EE068
—
—
—
—
—
—
—
—
—
H'EE069
—
—
—
—
—
—
—
—
—
H'EE06A —
—
—
—
—
—
—
—
—
H'EE06B —
—
—
—
—
—
—
—
—
H'EE06C —
—
—
—
—
—
—
—
—
H'EE06D —
—
—
—
—
—
—
—
—
H'EE06E —
—
—
—
—
—
—
—
—
H'EE06F
—
—
—
—
—
—
—
—
—
H'EE070
Reserved area (access prohibited)
—
—
RAMS
RAM2
RAM1
RAM0
Module
Name
H'EE071
H'EE072
H'EE073
H'EE074
H'EE075
H'EE076
H'EE077
RAMCR
*1
8
—
—
H'EE078
Reserved area (access prohibited)
Flash
memory*1
H'EE079
H'EE07A
H'EE07B
H'EE07C
H'EE07D
H'EE07E
H'EE07F
Rev. 3.00 Sep 14, 2005 page 749 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
OVF
WT/IT
TME
—
—
CKS2
CKS1
CKS0
WDT
H'EE090
TCSR*2
8
H'EE091
TCNT*2
8
Bit Names
H'EE092
—
—
—
—
—
—
—
—
—
H'EE093
RSTCSR*2 8
WRST
—
—
—
—
—
—
—
H'EE094
Reserved area (access prohibited)
H'EE095
H'EE096
H'EE097
H'EE098
H'EE099
H'EE09A
H'EE09B
H'EE09C
H'EE09D
H'EE09E
H'EE09F
H'EE0A0
H'EE0A1
H'EE0A2
H'EE0A3
H'EE0A4
H'EE0A5
H'EE0A6
H'EE0A7
H'EE0A8
H'EE0A9
H'EE0AA
H'EE0AB
H'EE0AC
H'EE0AD
H'EE0AE
H'EE0AF
Rev. 3.00 Sep 14, 2005 page 750 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
H'EE0B0 Reserved area (access prohibited)
H'EE0B1
H'EE0B2
H'EE0B3
H'EE0B4
H'EE0B5
H'EE0B6
H'EE0B7
H'EE0B8
H'EE0B9
H'EE0BA
H'EE0BB
H'EE0BC
H'EE0BD
H'EE0BE
H'EE0BF
H'EE0C0
H'EE0C1
H'EE0C2
H'EE0C3
H'EE0C4
H'EE0C5
H'EE0C6
H'EE0C7
H'EE0C8
H'EE0C9
H'EE0CA
H'EE0CB
H'EE0CC
H'EE0CD
H'EE0CE
H'EE0CF
Rev. 3.00 Sep 14, 2005 page 751 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
H'EE0D0 Reserved area (access prohibited)
H'EE0D1
H'EE0D2
H'EE0D3
H'EE0D4
H'EE0D5
H'EE0D6
H'EE0D7
H'EE0D8
H'EE0D9
H'EE0DA
H'EE0DB
H'EE0DC
H'EE0DD
H'EE0DE
H'EE0DF
H'EE0E0
H'EE0E1
H'EE0E2
H'EE0E3
H'EE0E4
H'EE0E5
H'EE0E6
H'EE0E7
H'EE0E8
H'EE0E9
H'EE0EA
H'EE0EB
H'EE0EC
H'EE0ED
H'EE0EE
H'EE0EF
Rev. 3.00 Sep 14, 2005 page 752 of 910
REJ09B0258-0300
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
Appendix B Internal I/O Registers
Address Register
(Low)
Name
H'EE0F0
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
Reserved area (access prohibited)
H'EE0F1
H'EE0F2
H'EE0F3
H'EE0F4
H'EE0F5
H'EE0F6
H'EE0F7
H'EE0F8
H'EE0F9
H'EE0FA
H'EE0FB
H'EE0FC
H'EE0FD
H'EE0FE
H'EE0FF
H'FFE00
—
—
—
—
—
—
—
—
—
H'FFE01
—
—
—
—
—
—
—
—
—
H'FFE02
—
—
—
—
—
—
—
—
—
H'FFE03
—
—
—
—
—
—
—
—
—
H'FFE04
—
—
—
—
—
—
—
—
—
H'FFE05
—
—
—
—
—
—
—
—
—
H'FFE06
—
—
—
—
—
—
—
—
—
H'FFE07
—
—
—
—
—
—
—
—
—
H'FFE08
—
—
—
—
—
—
—
—
—
H'FFE09
—
—
—
—
—
—
—
—
—
H'FFE0A —
—
—
—
—
—
—
—
—
H'FFE0B —
—
—
—
—
—
—
—
—
H'FFE0C —
—
—
—
—
—
—
—
—
H'FFE0D —
—
—
—
—
—
—
—
—
H'FFE0E —
—
—
—
—
—
—
—
—
H'FFE0F
—
—
—
—
—
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 753 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFE10
—
—
—
—
—
—
—
—
—
H'FFE11
—
—
—
—
—
—
—
—
—
H'FFE12
—
—
—
—
—
—
—
—
—
H'FFE13
—
—
—
—
—
—
—
—
—
H'FFE14
—
—
—
—
—
—
—
—
—
H'FFE15
—
—
—
—
—
—
—
—
—
H'FFE16
—
—
—
—
—
—
—
—
—
H'FFE17
—
—
—
—
—
—
—
—
—
H'FFE18
—
—
—
—
—
—
—
—
—
H'FFE19
—
—
—
—
—
—
—
—
—
H'FFE1A —
—
—
—
—
—
—
—
—
H'FFE1B —
—
—
—
—
—
—
—
—
H'FFE1C —
—
—
—
—
—
—
—
—
H'FFE1D —
—
—
—
—
—
—
—
—
H'FFE1E —
—
—
—
—
—
—
—
—
H'FFE1F
—
—
—
—
—
—
—
—
—
H'FFE20
—
—
—
—
—
—
—
—
—
H'FFE21
—
—
—
—
—
—
—
—
—
H'FFE22
—
—
—
—
—
—
—
—
—
H'FFE23
—
—
—
—
—
—
—
—
—
H'FFE24
—
—
—
—
—
—
—
—
—
H'FFE25
—
—
—
—
—
—
—
—
—
H'FFE26
—
—
—
—
—
—
—
—
—
H'FFE27
—
—
—
—
—
—
—
—
—
H'FFE28
—
—
—
—
—
—
—
—
—
H'FFE29
—
—
—
—
—
—
—
—
—
H'FFE2A —
—
—
—
—
—
—
—
—
H'FFE2B —
—
—
—
—
—
—
—
—
H'FFE2C —
—
—
—
—
—
—
—
—
H'FFE2D —
—
—
—
—
—
—
—
—
H'FFE2E —
—
—
—
—
—
—
—
—
H'FFE2F
—
—
—
—
—
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 754 of 910
REJ09B0258-0300
Module
Name
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFE30
—
—
—
—
—
—
—
—
—
H'FFE31
—
—
—
—
—
—
—
—
—
H'FFE32
—
—
—
—
—
—
—
—
—
H'FFE33
—
—
—
—
—
—
—
—
—
H'FFE34
—
—
—
—
—
—
—
—
—
H'FFE35
—
—
—
—
—
—
—
—
—
H'FFE36
—
—
—
—
—
—
—
—
—
H'FFE37
—
—
—
—
—
—
—
—
—
H'FFE38
—
—
—
—
—
—
—
—
—
H'FFE39
—
—
—
—
—
—
—
—
—
H'FFE3A —
—
—
—
—
—
—
—
—
H'FFE3B —
—
—
—
—
—
—
—
—
H'FFE3C —
—
—
—
—
—
—
—
—
H'FFE3D —
—
—
—
—
—
—
—
—
H'FFE3E —
—
—
—
—
—
—
—
—
H'FFE3F
—
—
—
—
—
—
—
—
—
H'FFE40
—
—
—
—
—
—
—
—
—
H'FFE41
—
—
—
—
—
—
—
—
—
H'FFE42
—
—
—
—
—
—
—
—
—
H'FFE43
—
—
—
—
—
—
—
—
—
H'FFE44
—
—
—
—
—
—
—
—
—
H'FFE45
—
—
—
—
—
—
—
—
—
H'FFE46
—
—
—
—
—
—
—
—
—
H'FFE47
—
—
—
—
—
—
—
—
—
H'FFE48
—
—
—
—
—
—
—
—
—
H'FFE49
—
—
—
—
—
—
—
—
—
H'FFE4A —
—
—
—
—
—
—
—
—
H'FFE4B —
—
—
—
—
—
—
—
—
H'FFE4C —
—
—
—
—
—
—
—
—
H'FFE4D —
—
—
—
—
—
—
—
—
H'FFE4E —
—
—
—
—
—
—
—
—
H'FFE4F
—
—
—
—
—
—
—
—
—
Module
Name
Rev. 3.00 Sep 14, 2005 page 755 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFE50
—
—
—
—
—
—
—
—
—
H'FFE51
—
—
—
—
—
—
—
—
—
H'FFE52
—
—
—
—
—
—
—
—
—
H'FFE53
—
—
—
—
—
—
—
—
—
H'FFE54
—
—
—
—
—
—
—
—
—
H'FFE55
—
—
—
—
—
—
—
—
—
H'FFE56
—
—
—
—
—
—
—
—
—
H'FFE57
—
—
—
—
—
—
—
—
—
H'FFE58
—
—
—
—
—
—
—
—
—
H'FFE59
—
—
—
—
—
—
—
—
—
H'FFE5A —
—
—
—
—
—
—
—
—
H'FFE5B —
—
—
—
—
—
—
—
—
H'FFE5C —
—
—
—
—
—
—
—
—
H'FFE5D —
—
—
—
—
—
—
—
—
H'FFE5E —
—
—
—
—
—
—
—
—
H'FFE5F
—
—
—
—
—
—
—
—
—
H'FFE60
—
—
—
—
—
—
—
—
—
H'FFE61
—
—
—
—
—
—
—
—
—
H'FFE62
—
—
—
—
—
—
—
—
—
H'FFE63
—
—
—
—
—
—
—
—
—
H'FFE64
—
—
—
—
—
—
—
—
—
H'FFE65
—
—
—
—
—
—
—
—
—
H'FFE66
—
—
—
—
—
—
—
—
—
H'FFE67
—
—
—
—
—
—
—
—
—
H'FFE68
—
—
—
—
—
—
—
—
—
H'FFE69
—
—
—
—
—
—
—
—
—
H'FFE6A —
—
—
—
—
—
—
—
—
H'FFE6B —
—
—
—
—
—
—
—
—
H'FFE6C —
—
—
—
—
—
—
—
—
H'FFE6D —
—
—
—
—
—
—
—
—
H'FFE6E —
—
—
—
—
—
—
—
—
H'FFE6F
—
—
—
—
—
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 756 of 910
REJ09B0258-0300
Module
Name
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFE70
—
—
—
—
—
—
—
—
—
H'FFE71
—
—
—
—
—
—
—
—
—
H'FFE72
—
—
—
—
—
—
—
—
—
H'FFE73
—
—
—
—
—
—
—
—
—
H'FFE74
—
—
—
—
—
—
—
—
—
H'FFE75
—
—
—
—
—
—
—
—
—
H'FFE76
—
—
—
—
—
—
—
—
—
H'FFE77
—
—
—
—
—
—
—
—
—
H'FFE78
—
—
—
—
—
—
—
—
—
H'FFE79
—
—
—
—
—
—
—
—
—
H'FFE7A —
—
—
—
—
—
—
—
—
H'FFE7B —
—
—
—
—
—
—
—
—
H'FFE7C —
—
—
—
—
—
—
—
—
H'FFE7D —
—
—
—
—
—
—
—
—
H'FFE7E —
—
—
—
—
—
—
—
—
H'FFE7F
—
—
—
—
—
—
—
—
—
H'FFE80
MAR0AR
8
H'FFE81
MAR0AE
8
H'FFE82
MAR0AH
8
H'FFE83
MAR0AL
8
H'FFE84
ETCR0AH 8
H'FFE85
ETCR0AL 8
H'FFE86
IOAR0A
8
H'FFE87
DTCR0A
8
H'FFE88
MAR0BR
8
H'FFE89
MAR0BE
8
H'FFE8A MAR0BH
8
H'FFE8B MAR0BL
8
Module
Name
DMAC
channel 0A
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
Short
address
mode
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A
DTS1A
DTS0A
Full address
mode
DMAC
channel 0B
H'FFE8C ETCR0BH 8
H'FFE8D ETCR0BL 8
H'FFE8E IOAR0B
8
H'FFE8F
8
DTCR0B
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
Short
address
mode
DTME
—
DAID
DAIDE
TMS
DTS2B
DTS1B
DTS0B
Full address
mode
Rev. 3.00 Sep 14, 2005 page 757 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
H'FFE90
MAR1AR
8
H'FFE91
MAR1AE
8
H'FFE92
MAR1AH
8
H'FFE93
MAR1AL
8
H'FFE94
ETCR1AH 8
H'FFE95
ETCR1AL 8
H'FFE96
IOAR1A
8
H'FFE97
DTCR1A
8
H'FFE98
MAR1BR
8
H'FFE99
MAR1BE
8
H'FFE9A MAR1BH
8
H'FFE9B MAR1BL
8
Bit Names
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
DMAC
channel 1A
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
Short
address
mode
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A
DTS1A
DTS0A
Full address
mode
DMAC
channel 1B
H'FFE9C ETCR1BH 8
H'FFE9D ETCR1BL 8
H'FFE9E IOAR1B
8
H'FFE9F
8
DTCR1B
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
Short
address
mode
DTME
—
DAID
DAIDE
TMS
DTS2B
DTS1B
DTS0B
Full address
mode
16-bit timer,
(all channels)
H'FFEA0 TSTR
8
—
—
—
—
—
STR2
STR1
STR0
H'FFEA1 TSNC
8
—
—
—
—
—
SYNC2
SYNC1
SYNC0
H'FFEA2 TMDR
8
—
MDF
FDIR
—
—
PWM2
PWM1
PWM0
H'FFEA3 TOLR
8
—
—
TOB2
TOA2
TOB1
TOA1
TOB0
TOA0
H'FFEA4 TISRA
8
—
IMIEA2
IMIEA1
IMIEA0
—
IMFA2
IMFA1
IMFA0
H'FFEA5 TISRB
8
—
IMIEB2
IMIEB1
IMIEB0
—
IMFB2
IMFB1
IMFB0
H'FFEA6 TISRC
8
—
OVIE2
OVIE1
OVIE0
—
OVF2
OVF1
OVF0
H'FFEA8 16TCR0
8
—
CCLR1
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
H'FFEA9 TIOR0
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'FFEA7 —
H'FFEAA 16TCNT0H 16
H'FFEAB 16TCNT0L
H'FFEAC GRA0H
16
H'FFEAD GRA0L
H'FFEAE GRB0H
16
H'FFEAF GRB0L
Rev. 3.00 Sep 14, 2005 page 758 of 910
REJ09B0258-0300
16-bit timer
channel 0
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit 6
Bit 5
H'FFEB0 16TCR1
8
—
CCLR1
H'FFEB1 TIOR1
8
—
IOB2
Bit Names
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
IOB1
IOB0
—
IOA2
IOA1
IOA0
Module
Name
16-bit timer
channel 1
H'FFEB2 16TCNT1H 16
H'FFEB3 16TCNT1L
H'FFEB4 GRA1H
16
H'FFEB5 GRA1L
H'FFEB6 GRB1H
16
H'FFEB7 GRB1L
H'FFEB8 16TCR2
8
—
CCLR1
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
H'FFEB9 TIOR2
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
16-bit timer
channel 2
H'FFEBA 16TCNT2H 16
H'FFEBB 16TCNT2L
H'FFEBC GRA2H
16
H'FFEBD GRA2L
H'FFEBE GRB2H
16
H'FFEBF GRB2L
H'FFEC0 8TCR0
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFEC1 8TCR1
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFEC2 8TCSR0
8
CMFB
CMFA
OVF
ADTE
OIS3
OIS2
OS1
OS0
H'FFEC3 8TCSR1
8
CMFB
CMFA
OVF
ICE
OIS3
OIS2
OS1
OS0
H'FFEC4 TCORA0
8
H'FFEC5 TCORA1
8
H'FFEC6 TCORB0
8
H'FFEC7 TCORB1
8
H'FFEC8 8TCNT0
8
H'FFEC9 8TCNT1
8
8-bit timer
channels 0
and 1
H'FFECA Reserved area (access prohibited)
H'FFECB
H'FFECC
H'FFECD
H'FFECE
H'FFECF
Rev. 3.00 Sep 14, 2005 page 759 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'FFED0 8TCR2
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
H'FFED1 8TCR3
8
CMIEB
CMIEA
OVIE
CCLR1
CCLR0
CKS2
CKS1
CKS0
Bit Names
H'FFED2 8TCSR2
8
CMFB
CMFA
OVF
—
OIS3
OIS2
OS1
OS0
H'FFED3 8TCSR3
8
CMFB
CMFA
OVF
ICE
OIS3
OIS2
OS1
OS0
H'FFED4 TCORA2
8
H'FFED5 TCORA3
8
H'FFED6 TCORB2
8
H'FFED7 TCORB3
8
H'FFED8 8TCNT2
8
H'FFED9 8TCNT3
8
Module
Name
8-bit timer
channels 2
and 3
H'FFEDA Reserved area (access prohibited)
H'FFEDB
H'FFEDC
H'FFEDD
H'FFEDE
H'FFEDF
H'FFEE0 SMR
8
H'FFEE1 BRR
8
H'FFEE2 SCR
8
H'FFEE3 TDR
8
H'FFEE4 SSR
8
H'FFEE5 RDR
8
H'FFEE6 SCMR
8
H'FFEE7 —
H'FFEE8 SMR
8
H'FFEE9 BRR
8
H'FFEEA SCR
8
H'FFEEB TDR
8
H'FFEEC SSR
8
H'FFEED RDR
8
H'FFEEE SCMR
8
H'FFEEF —
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
TDRE
RDRF
ORER
FER/
ERS
PER
TEND
MPB
MPBT
—
—
—
—
SDIR
SINV
—
SMIF
—
—
—
—
—
—
—
—
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
TDRE
RDRF
ORER
FER/
ERS
PER
TEND
MPB
MPBT
—
—
—
—
SDIR
SINV
—
SMIF
—
—
—
—
—
—
—
—
Rev. 3.00 Sep 14, 2005 page 760 of 910
REJ09B0258-0300
SCI
channel 0
SCI
channel 1
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
TDRE
RDRF
ORER
FER/
ERS
PER
TEND
MPB
MPBT
—
—
—
—
SDIR
SINV
—
SMIF
—
—
—
—
—
—
—
—
—
—
—
—
G3NOV G2NOV
G1NOV
G0NOV
H'FFEF0
SMR
8
H'FFEF1
BRR
8
H'FFEF2
SCR
8
H'FFEF3
TDR
8
H'FFEF4
SSR
8
H'FFEF5
RDR
8
H'FFEF6
SCMR
8
H'FFEF7
—
H'FFEF8
TPMR
H'FFEF9
TPCR
8
Bit Names
8
G3CMS1 G3CMS0 G2CMS1 G2CMS0 G1CMS1 G1CMS0 G0CMS1 G0CMS0
H'FFEFA NDERB
8
NDER15 NDER14 NDER13 NDER12 NDER11 NDER10 NDER9
NDER8
H'FFEFB NDERA
8
NDER7
3
8
H'FFEFC NDRB*
H'FFEFD NDRA*3
8
H'FFEFE NDRB*3
8
H'FFEFF NDRA*3
8
NDER6
NDER5
NDER4
NDER3
NDER2
NDER1
NDER0
NDR8
NDR15
NDR14
NDR13
NDR12
NDR11
NDR10
NDR9
NDR15
NDR14
NDR13
NDR12
—
—
—
—
NDR7
NDR6
NDR5
NDR4
NDR3
NDR2
NDR1
NDR0
NDR7
NDR6
NDR5
NDR4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NDR11
NDR10
NDR9
NDR8
—
—
—
—
—
—
—
—
—
—
—
—
NDR3
NDR2
NDR1
NDR0
H'FFFE0
ADDRAH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'FFFE1
ADDRAL
8
AD1
AD0
—
—
—
—
—
—
H'FFFE2
ADDRBH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'FFFE3
ADDRBL
8
AD1
AD0
—
—
—
—
—
—
H'FFFE4
ADDRCH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'FFFE5
ADDRCL
8
AD1
AD0
—
—
—
—
—
—
H'FFFE6
ADDRDH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'FFFE7
ADDRDL
8
AD1
AD0
—
—
—
—
—
—
H'FFFE8
ADCSR
8
ADF
ADIE
ADST
SCAN
CKS
CH2
CH1
CH0
H'FFFE9
ADCR
8
TRGE
—
—
—
—
—
—
—
Module
Name
SCI
channel 2
A/D
converter
H'FFFEA Reserved area (access prohibited)
H'FFFEB
H'FFFEC DADR0
8
H'FFFED DADR1
8
H'FFFEE DACR
8
—
—
—
—
—
—
—
—
H'FFFEF —
8
—
—
—
—
—
—
—
—
D/A
converter
Rev. 3.00 Sep 14, 2005 page 761 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
Address Register
(Low)
Name
Data
Bus
Width Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module
Name
H'FFFF0
P1DR
8
P17
P16
P15
P14
P13
P12
P11
P10
Port1
H'FFFF1
P2DR
8
P27
P26
P25
P24
P23
P22
P21
P20
Port2
H'FFFF2
P3DR
8
P37
P36
P35
P34
P33
P32
P31
P30
Port3
H'FFFF3
P4DR
8
P47
P46
P45
P44
P43
P42
P41
P40
Port4
H'FFFF4
P5DR
8
—
—
—
—
P53
P52
P51
P50
Port5
H'FFFF5
P6DR
8
P67
P66
P65
P64
P63
P62
P61
P60
Port6
H'FFFF6
P7DR
8
P77
P76
P75
P74
P73
P72
P71
P70
Port7
H'FFFF7
P8DR
8
—
—
—
P84
P83
P82
P81
P80
Port8
H'FFFF8
P9DR
8
—
—
P95
P94
P93
P92
P91
P90
Port9
H'FFFF9
PADR
8
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
PortA
H'FFFFA PBDR
8
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
PortB
H'FFFFB —
—
—
—
—
—
—
—
—
H'FFFFC —
—
—
—
—
—
—
—
—
H'FFFFD —
—
—
—
—
—
—
—
—
H'FFFFE —
—
—
—
—
—
—
—
—
H'FFFFF
—
—
—
—
—
—
—
—
—
Bit Names
Notes: 1. The RAMCR and FLMCR registers are used only in the flash memory and flash
memory R versions, and are not provided in the mask ROM versions.
2. For write access to TCSR, TCNT, and RSTCSR, see section 12.2.4, Notes on Register
Access.
3. The address depends on the output trigger setting.
Legend
WDT: Watchdog timer
TPC: Programmable timing pattern controller
SCI: Serial communication interface
Rev. 3.00 Sep 14, 2005 page 762 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
B.3
Functions
Register abbreviation
Address to which register
is mapped*
Register name
TIER—Timer Interrupt Enable Register
H' 90
Name of on-chip
supporting module
FRT
Bit numbers
Bit
Initial bit values
Initial value
R/W:
6
5
ICIAE
ICIBE
ICICE
0
R/W
0
R/W
0
R/W
OCIDE OCIAE OCIBE
Read only
W
Write only
0
OVIE
1
R/W
1
R/W
0
R/W
0
R/W
1
Names of the bits.
Dashes (—) indicate
reserved bits.
Timer overflow interrupt enable
Possible types of
access
R
1
2
3
4
7
R/W Read and write
0
Interrupt requested by OVF flag is disabled
1
Interrupt requested by OVF flag is enabled
Output compare interrupt B enable
0
Interrupt requested by OCFB flag is disabled
1
Interrupt requested by OCFB flag is enabled
Full name of bit
Output compare interrupt A enable
0
Interrupt requested by OCFA flag is disabled
1
Interrupt requested by OCFA flag is enabled
Descriptions of
bit settings
Input capture interrupt D enable
0
Interrupt requested by ICFD flag is disabled
1
Interrupt requested by ICFD flag is enabled
Note: * When the EMC bit in BCR is cleared to 0, addresses of some registers are changed.
Rev. 3.00 Sep 14, 2005 page 763 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
P1DDR—Port 1 Data Direction Register
Bit
7
6
H'EE000
5
4
3
Port 1
2
1
0
P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR P11DDR P10DDR
Modes 1 to 4
Initial value
Read/Write
1
1
1
1
1
1
1
1
Modes 5 to 7
Initial value
Read/Write
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
Port 1 input/output select
0
Generic input
1
Generic output
P2DDR—Port 2 Data Direction Register
Bit
7
6
H'EE001
5
4
3
Port 2
2
1
0
P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR P21DDR P20DDR
Modes 1 to 4
Initial value
Read/Write
1
1
1
1
1
1
1
1
Modes 5 to 7
Initial value
Read/Write
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
Port 2 input/output select
Rev. 3.00 Sep 14, 2005 page 764 of 910
REJ09B0258-0300
0
Generic input
1
Generic output
Appendix B Internal I/O Registers
P3DDR—Port 3 Data Direction Register
Bit
7
6
H'EE002
5
4
3
2
Port 3
1
0
P37DDR P36DDR P35DDR P34DDR P33DDR P32DDR P31DDR P30DDR
Initial value
Read/Write
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
Port 3 input/output select
0
Generic input
1
Generic output
P4DDR—Port 4 Data Direction Register
Bit
7
6
H'EE003
5
4
3
2
Port 4
1
0
P47DDR P46DDR P45DDR P44DDR P43DDR P42DDR P41DDR P40DDR
Initial value
Read/Write
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
Port 4 input/output select
0
Generic input
1
Generic output
Rev. 3.00 Sep 14, 2005 page 765 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
P5DDR—Port 5 Data Direction Register
Bit
7
6
H'EE004
5
4
Port 5
2
3
1
0
P53DDR P52DDR P51DDR P50DDR
Modes 1 to 4
Initial value
Read/Write
1
1
1
1
1
1
1
1
Modes 5 to 7
Initial value
Read/Write
1
1
1
1
0
W
0
W
0
W
0
W
Port 5 input/output select
P6DDR—Port 6 Data Direction Register
Bit
7
6
0
Generic input pin
1
Generic output pin
H'EE005
5
4
3
2
Port 6
1
0
P66DDR P65DDR P64DDR P63DDR P62DDR P61DDR P60DDR
Initial value
Read/Write
1
0
W
0
W
0
W
0
W
0
W
Port 6 input/output select
Rev. 3.00 Sep 14, 2005 page 766 of 910
REJ09B0258-0300
0
Generic input
1
Generic output
0
W
0
W
Appendix B Internal I/O Registers
P8DDR—Port 8 Data Direction Register
Bit
7
6
H'EE007
5
4
3
Port 8
2
1
0
P84DDR P83DDR P82DDR P81DDR P80DDR
Modes 1 to 4
Initial value
Read/Write
1
1
1
1
W
0
W
0
W
0
W
0
W
Modes 5 to 7
Initial value
Read/Write
1
1
1
0
W
0
W
0
W
0
W
0
W
Port 8 input/output select
0
Generic input
1
Generic output
Rev. 3.00 Sep 14, 2005 page 767 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
P9DDR—Port 9 Data Direction Register
Bit
7
6
H'EE008
5
4
3
2
Port 9
1
0
P95DDR P94DDR P93DDR P92DDR P91DDR P90DDR
Initial value
Read/Write
1
1
0
W
0
W
0
W
0
W
0
W
0
W
Port 9 input/output select
0
Generic input
1
Generic output
PADDR—Port A Data Direction Register
Bit
7
6
H'EE009
5
4
3
Port A
2
1
0
PA7DDR PA6DDR PA5DDR PA4DDR PA3DDR PA2DDR PA1DDR PA0DDR
Modes 3, 4
Initial value
Read/Write
1
0
W
0
W
0
W
0
W
0
W
0
W
0
W
Modes
1, 2, 5, 6, 7
Initial value
Read/Write
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
Port A input/output select
0
Generic input
1
Generic output
PBDDR—Port B Data Direction Register
Bit
7
6
H'EE00A
5
4
3
2
Port B
1
0
PB7DDR PB6DDR PB5DDR PB4DDR PB3DDR PB2DDR PB1DDR PB0DDR
Initial value
Read/Write
0
W
0
W
0
W
0
W
0
W
0
W
Port B input/output select
Rev. 3.00 Sep 14, 2005 page 768 of 910
REJ09B0258-0300
0
Generic input
1
Generic output
0
W
0
W
Appendix B Internal I/O Registers
MDCR—Mode Control Register
Bit
Initial value
Read/Write
7
1
6
1
H'EE011
5
0
4
0
3
System control
2
1
0
MDS2
MDS1
MDS0
*
0
R
*
R
*
R
Mode select 2 to 0
Bit 2
Bit 1
Bit 0
MD2
MD1
MD0
0
0
1
0
1
1
Operating Mode
0
1
Mode 1
0
Mode 2
1
Mode 3
0
Mode 4
1
Mode 5
0
Mode 6
1
Mode 7
Note: * Determined by the state of the mode pins (MD2 to MD0).
Rev. 3.00 Sep 14, 2005 page 769 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
SYSCR—System Control Register
Bit
Initial value
Read/Write
H'EE012
System control
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
SSOE
RAME
0
R/W
0
R/W
0
R/W
0
R/W
1
R/W
0
R/W
0
R/W
1
R/W
RAM enable
0
1
On-chip RAM is disabled
On-chip RAM is enabled
Software standby output port enable
0
1
In software standby mode,
all address bus and bus
control signals are highimpedance
In software standby mode,
address bus retains output
state and bus control
signals are fixed high
NMI edge select
An interrupt is requested at the falling edge of NMI
0
An interrupt is requested at the rising edge of NMI
1
User bit enable
CCR bit 6 (UI) is used as an interrupt mask bit
0
CCR bit 6 (UI) is used as a user bit
1
Standby timer select 2 to 0
Bit 6
STS2
Bit 5
STS1
0
0
1
0
1
1
Bit 4
STS0
0
1
0
1
0
1
0
1
Standby Timer
Waiting Time = 8,192 states
Waiting Time = 16,384 states
Waiting Time = 32,768 states
Waiting Time = 65,536 states
Waiting Time = 131,072 states
Waiting Time = 26,2144 states
Waiting Time = 1,024 states
Illegal setting
Software standby
0
1
SLEEP instruction causes transition to sleep mode
SLEEP instruction causes transition to software standby mode
Rev. 3.00 Sep 14, 2005 page 770 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
BRCR—Bus Release Control Register
Bit
H'EE013
7
6
5
4
3
A23E
A22E
A21E
A20E
Bus controller
2
1
0
BRLE
Modes
1, 2, 6, 7
Initial value
Read/Write
1
1
1
1
1
1
1
0
R/W
Modes
3, 4
Initial value
Read/Write
1
R/W
1
R/W
1
R/W
0
1
1
1
0
R/W
Mode 5
Initial value
Read/Write
1
R/W
1
R/W
1
R/W
1
R/W
1
1
1
0
R/W
Bus release enable
Address 23 to 20 enable
0
Address output
1
Other input/output
0
1
ISCR—IRQ Sense Control Register
Bit
7
6
5
H'EE014
4
3
2
The bus cannot be
released to an
external device
The bus can be
released to an
external device
Interrupt Controller
1
0
IRQ5SC IRQ4SC IRQ3SC IRQ2SC IRQ1SC IRQ0SC
Initial value
Read/Write
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
IRQ5 to IRQ0 sense control
0
Interrupts are requested when IRQ5 to IRQ0 are low
1
Interrupts are requested by falling-edge input at IRQ5 to IRQ0
Rev. 3.00 Sep 14, 2005 page 771 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
IER—IRQ Enable Register
Bit
Initial value
Read/Write
H'EE015
7
6
0
R/W
0
R/W
Interrupt Controller
5
4
3
2
1
0
IRQ5E
IRQ4E
IRQ3E
IRQ2E
IRQ1E
IRQ0E
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
IRQ5 to IRQ0 enable
0
IRQ5 to IRQ0 interrupts are disabled
1
IRQ5 to IRQ0 interrupts are enabled
ISR—IRQ Status Register
Bit
Initial value
Read/Write
H'EE016
6
7
0
0
Interrupt Controller
5
4
3
2
1
0
IRQ5F
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
0
R/(W)*
0
R/(W)*
0
R/(W)*
0
R/(W)*
0
R/(W)*
0
R/(W)*
IRQ5 to IRQ0 flags
Bits 5 to 0
Setting and Clearing Conditions
IRQ5F to IRQ0F
[Clearing conditions]
• Read IRQnF when IRQnF = 1, then write 0 in IRQnF.
0
• IRQnSC = 0, IRQn input is high, and interrupt exception
handling is being carried out.
• IRQnSC = 1 and IRQn interrupt exception handling is being
carried out.
[Setting conditions]
1
• IRQnSC = 0 and IRQn input is low.
• IRQnSC = 1 and IRQn input changes from high to low.
(n = 5 to 0)
Note: * Only 0 can be written, to clear the flag.
Rev. 3.00 Sep 14, 2005 page 772 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
IPRA—Interrupt Priority Register A
Interrupt Controller
7
6
5
4
3
2
1
0
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Bit
Initial value
Read/Write
H'EE018
Priority level A7 to A0
0
Priority level 0 (low priority)
1
Priority level 1 (high priority)
• Interrupt sources controlled by each bit
Bit
IPRA
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
IRQ0
IRQ1
IRQ2,
IRQ4,
WDT,
16-bit
16-bit
16-bit
IRQ3
IRQ5
DRAM
timer
timer
timer
Interrupt
source
interface, channel 0 channel 1 channel 2
A/D converter
IPRB—Interrupt Priority Register B
Bit
Initial value
Read/Write
H'EE019
7
6
5
IPRB7
IPRB6
IPRB5
0
R/W
0
R/W
0
R/W
4
0
R/W
Interrupt Controller
3
2
1
IPRB3
IPRB2
IPRB1
0
R/W
0
R/W
0
R/W
0
0
R/W
Priority level B7 to B5, B3 to B1
0
Priority level 0 (low priority)
1
Priority level 1 (high priority)
• Interrupt sources controlled by each bit
Bit
IPRB
Bit 7
Bit 6
Bit 5
IPRB7
IPRB6
IPRB5
8-bit timer 8-bit timer
Interrupt
channels channels
source
0 and 1 2 and 3
DMAC
Bit 4
Bit 3
Bit 2
Bit 1
IPRB3
IPRB2
IPRB1
SCI
SCI
SCI
Bit 0
channel 0 channel 1 channel 2
Rev. 3.00 Sep 14, 2005 page 773 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
DASTCR—D/A Standby Control Register
Bit
7
6
5
H'EE01A
4
3
2
D/A
1
0
DASTE
Initial value
Read/Write
1
1
1
1
1
1
1
0
R/W
D/A standby enable
0
D/A output is disabled in software standby mode
1
D/A output is enabled in software standby mode
Rev. 3.00 Sep 14, 2005 page 774 of 910
REJ09B0258-0300
(Initial value)
Appendix B Internal I/O Registers
DIVCR—Division Control Register
Bit
Initial value
Read/Write
7
1
6
1
5
1
H'EE01B
4
1
3
2
1
1
System control
1
0
DIV1
DIV0
0
R/W
0
R/W
Divide 1 and 0
Bit 1
Bit 0
DIV1
DIV0
0
1
Frequency Division Ratio
0
1/1
1
1/2
0
1/4
1
1/8
(Initial value)
Rev. 3.00 Sep 14, 2005 page 775 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
MSTCRH—Module Standby Control Register H
7
Bit
6
4
5
H'EE01C
3
PSTOP
Initial value
0
Read/Write
R/W
2
System control
1
0
MSTPH2 MSTPH1 MSTPH0
1
1
1
1
0
0
R/W
R/W
0
R/W
Module standby H2 to H0
Selection bits for placing modules
in standby state.
Reserved bits
φ clock stop
Enables or disables ø clock output.
MSTCRL—Module Standby Control Register L
Bit
7
6
MSTPL7
5
4
H'EE01D
System control
3
1
2
MSTPL5 MSTPL4 MSTPL3 MSTPL2
Initial value
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
MSTPL0
0
R/W
Module standby L7, L5 to L2, L0
Selection bits for placing modules
in standby state.
Reserved bits
Rev. 3.00 Sep 14, 2005 page 776 of 910
REJ09B0258-0300
0
0
R/W
Appendix B Internal I/O Registers
ADRCR—Address Control Register
Bit
H'EE01E
Bus controller
7
6
5
4
3
2
1
0







ADRCTL
Initial value
1
1
1
1
1
1
1
1
Read/Write







R/W
Reserved bits
Address control
Selects address update
mode 1 or address
update mode 2.
Description
ADRCTL
0
Address update mode 2 is selected
1
Address update mode 1 is selected (Initial value)
Note: * This register is used only in the flash memory R version and mask ROM version.
CSCR—Chip Select Control Register
Bit
Initial value
Read/Write
H'EE01F
7
6
5
4
CS7E
CS6E
CS5E
CS4E
0
R/W
0
R/W
0
R/W
0
R/W
Bus controller
3
2
1
0
1
1
1
1
Chip select 7 to 4 enable
Bit n
Description
CSnE
0
Output of chip select signal CSn is disabled (Initial value)
1
Output of chip select signal CSn is enabled
(n = 7 to 4)
Rev. 3.00 Sep 14, 2005 page 777 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
ABWCR—Bus Width Control Register
Bit
Modes 1, 3, 5, 6, 7 Initial value
Initial value
Modes 2, 4
Read/Write
H'EE020
Bus controller
7
6
5
4
3
2
1
0
ABW7
ABW6
ABW5
ABW4
ABW3
ABW2
ABW1
ABW0
1
0
R/W
1
0
R/W
1
0
R/W
1
0
R/W
1
0
R/W
1
0
R/W
1
0
R/W
1
0
R/W
Area 7 to 0 bus width control
Bits 7 to 0
Bus Width of Access Area
ABW7
to ABW0
0
Areas 7 to 0 are 16-bit access areas
1
Areas 7 to 0 are 8-bit access areas
ASTCR—Access State Control Register
Bit
Initial value
Read/Write
H'EE021
Bus controller
7
6
5
4
3
2
1
0
AST7
AST6
AST5
AST4
AST3
AST2
AST1
AST0
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
Area 7 to 0 access state control
Bits 7 to 0
AST7
Number of States in Access Area
to AST0
0
Areas 7 to 0 are two-state access areas
1
Areas 7 to 0 are three-state access areas
Rev. 3.00 Sep 14, 2005 page 778 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
WCRH—Wait Control Register H
Bit
Initial value
Read/Write
H'EE022
7
6
5
4
3
2
1
0
W71
W70
W61
W60
W51
W50
W41
W40
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
Bus controller
Area 4 wait control 1 and 0
0 No program wait is inserted
0
1 1 program wait state is inserted
1
0
2 program wait states are inserted
1
3 program wait states are inserted
Area 5 wait control 1 and 0
0 No program wait is inserted
0
1 1 program wait state is inserted
1
0
2 program wait states are inserted
1
3 program wait states are inserted
Area 6 wait control 1 and 0
0 No program wait is inserted
0
1 1 program wait state is inserted
1
0
2 program wait states are inserted
1
3 program wait states are inserted
Area 7 wait control 1 and 0
0 No program wait is inserted
0
1 1 program wait state is inserted
1
0
2 program wait states are inserted
1
3 program wait states are inserted
Rev. 3.00 Sep 14, 2005 page 779 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
WCRL—Wait Control Register L
Bit
Initial value
Read/Write
H'EE023
Bus controller
7
6
5
4
3
2
1
0
W31
W30
W21
W20
W11
W10
W01
W00
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
Area 0 wait control 1 and 0
0
1
0
No program wait is inserted
1
1 program wait state is inserted
0
2 program wait states are inserted
1
3 program wait states are inserted
Area 1 wait control 1 and 0
0
1
0
No program wait is inserted
1
1 program wait state is inserted
0
2 program wait states are inserted
1
3 program wait states are inserted
Area 2 wait control 1 and 0
0
1
0
No program wait is inserted
1
1 program wait state is inserted
0
2 program wait states are inserted
1
3 program wait states are inserted
Area 3 wait control 1 and 0
0
1
0
No program wait is inserted
1
1 program wait state is inserted
0
2 program wait states are inserted
1
3 program wait states are inserted
Rev. 3.00 Sep 14, 2005 page 780 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
BCR—Bus Control Register
Bit
Initial value
Read/Write
7
6
ICIS1
ICIS0
1
R/W
1
R/W
H'EE024
5
4
3
BROME BRSTS1 BRSTS0
0
R/W
0
R/W
0
R/W
Bus controller
2
1
0
—
RDEA
WAITE
1
—
1
R/W
0
R/W
Wait pin enable
0
WAIT pin wait input is disabled
1
WAIT pin wait input is enabled
Area division unit select
0
1
Area divisions are as follows:
Area 0: 2 MB
Area 1: 2 MB
Area 4: 1.93 MB
Area 5: 4 kB
Area 2: 8 MB
Area 3: 2 MB
Area 6: 23.75 kB
Area 7: 22 B
Areas 0 to 7 are the same size
(2 MB)
Burst cycle select 0
0
Max. 4 words in burst access
1
Max. 8 words in burst access
Burst cycle select 1
0
Burst access cycle comprises 2 states
1
Burst access cycle comprises 3 states
Burst ROM enable
0
Area 0 is a basic bus interface area
1
Area 0 is a burst ROM interface area
Idle cycle insertion 0
0
No idle cycle is inserted in case of consecutive external read and write cycles
1
Idle cycle is inserted in case of consecutive external read and write cycles
Idle cycle insertion 1
0
No idle cycle is inserted in case of consecutive external read cycles for different areas
1
Idle cycle is inserted in case of consecutive external read cycles for different areas
Rev. 3.00 Sep 14, 2005 page 781 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
DRCRA—DRAM Control Register A
Bit
7
6
H'EE026
5
4
3
DRAS2 DRAS1 DRAS0
Initial value
0
0
0
Read/Write
R/W
R/W
R/W
2
BE
1
DRAM interface
1
0
RDM SRFMD RFSHE
0
0
0
0
R/W
R/W
R/W
R/W
Refresh pin enable
0
RFSH pin refresh signal output is disabled
1
RFSH pin refresh signal output is enabled
Self-refresh mode
DRAM self-refreshing is disabled in
0
software standby mode
DRAM self-refreshing is enabled
1
in software standby mode
RAS down mode
0
DRAM interface: RAS up mode selected
1
DRAM interface: RAS down mode selected
Burst access enable
0
Burst disabled (always full access)
1
DRAM space access performed in fast page mode
DRAM area select
DRAS2 DRAS1 DRAS0
0
0
Area 5
Area 4
Area 3
0
Normal
Normal
Normal
Normal
1
Normal
Normal
Normal
DRAM space
Area 2
(CS2)
1
0
Normal
Normal
1
Normal
Normal
0
Normal
DRAM space DRAM space
(CS3)
1
0
DRAM space DRAM space DRAM space
(CS4)
1
0
1
(CS3)
(CS2)
DRAM space DRAM space DRAM space DRAM space
(CS5)
1
(CS2)
DRAM space(CS2)*
(CS4)
DRAM space(CS4)*
(CS3)
(CS2)
DRAM space(CS2)*
DRAM space(CS2)*
Note: * A single CSn pin serves as a common RAS output pin for a number of
areas. Unused CSn pins can be used as input/output ports.
Rev. 3.00 Sep 14, 2005 page 782 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
DRCRB—DRAM Control Register B
Bit
7
6
MXC1
MXC0
H'EE027
5
4
3
CSEL RCYCE
Initial value
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
1
2
1
0
TPC
RCW
RLW
0
0
0
R/W
R/W
R/W
DRAM interface
Refresh cycle wait control
0
Wait state (TRW) insertion is disabled
1
1 wait state (TRW) is inserted
RAS-CAS wait
0
Wait state (Trw) insertion is disabled
1
1 wait state (Trw) is inserted
TP cycle control
0
1-state precharge cycle is inserted
1
2-state precharge cycle is inserted
Refresh cycle enable
0
Refresh cycles are disabled
1
DRAM refresh cycles are enabled
CAS output pin select
0
PB4 and PB5 selected as UCAS and LCAS output pins
1
HWR and LWR selected as UCAS and LCAS output pins
Multiplex control 1 and 0
MXC1
MXC0
0
0
Description
Column address: 8 bits
Compared address:
Modes 1, 2
Modes 3, 4, 5
1
8-bit access space
16-bit access space
8-bit access space
16-bit access space
Column address: 9 bits
Compared address:
Modes 1, 2
8-bit access space
16-bit access space
0
1
A19 to A9
A19 to A10
8-bit access space
16-bit access space
A23 to A9
A23 to A10
Column address: 10 bits
Compared address:
Modes 1, 2
8-bit access space
16-bit access space
Modes 3, 4, 5
8-bit access space
16-bit access space
A19 to A10
A19 to A11
A23 to A10
A23 to A11
Modes 3, 4, 5
1
A19 to A8
A19 to A9
A23 to A8
A23 to A9
Illegal setting
Rev. 3.00 Sep 14, 2005 page 783 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
RTMCSR—Refresh Timer Control/Status Register
Bit
H'EE028
7
6
5
4
3
CMF
CMIE
CKS2
CKS1
CKS0
Initial value
0
0
0
0
0
Read/Write
R/(W)*
R/W
R/W
R/W
R/W
DRAM interface
2
1
0
1
1
1
Refresh counter clock select
CKS2
CKS1
0
0
1
1
0
1
Description
CKS0
0
Count operation halted
1
φ/2 used as counter clock
0
φ/8 used as counter clock
1
φ/32 used as counter clock
0
φ/128 used as counter clock
1
φ/512 used as counter clock
0
φ/2048 used as counter clock
1
φ/4096 used as counter clock
Compare match interrupt enable
0
The CMI interrupt requested by the CMF flag is disabled
1
The CMI interrupt requested by the CMF flag is enabled
Compare match flag
0
[Clearing conditions]
• Cleared by a reset and in standby mode
• Cleared by reading CMF when CMF = 1, then writing 0 in CMF
1
[Setting condition]
When RTCNT = RTCOR
Note: * Only 0 can be written to clear the flag.
Rev. 3.00 Sep 14, 2005 page 784 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
RTCNT—Refresh Timer Counter
H'EE029
DRAM interface
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Incremented by internal clock selected
by bits CKS2 to CKS0 in RTMCSR
RTCOR—Refresh Time Constant Register
H'EE02A
DRAM interface
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RTCNT compare match period
Note: Only byte access can be used on this register.
Rev. 3.00 Sep 14, 2005 page 785 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
FLMCR1—Flash Memory Control Register 1
H'EE030
Flash Memory
7
6
5
4
3
2
1
0
FWE
SWE
ESU
PSU
EV
PV
E
P
Bit
Modes 1 to
4, and 6
Initial value
Read/Write
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
Modes 5
and 7
Initial value
Read/Write
1/0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Program mode
0
Program mode cleared (Initial value)
1
Transition to program mode
[Setting condition]
When FWE = 1, SWE = 1, and PSU = 1
Erase mode
0
Erase mode cleared (Initial value)
1
Transition to erase mode
[Setting condition]
When FWE = 1, SWE = 1, and ESU = 1
Program-verify mode
0
Program-verify mode cleared (Initial value)
1
Transition to program-verify mode
[Setting condition]
When FWE = 1 and SWE = 1
Erase-verify mode
0
Erase-verify mode cleared (Initial value)
1
Transition to erase-verify mode
[Setting condition]
When FWE = 1 and SWE = 1
Program setup
0
Program setup cleared (Initial value)
1
Program setup
[Setting condition]
When FWE = 1 and SWE = 1
Erase setup bit
0
Erase setup cleared (Initial value)
1
Erase setup
[Setting condition]
When FWE = 1 and SWE = 1
Software write enable bit
0
Write/erase disabled (Initial value)
1
Write/erase enabled
[Setting condition]
When FWE = 1
Flash write enable bit
0
When a low level is input to the FWE pin (hardware protection state)
1
When a high level is input to the FWE pin
Note: This register is used only in the flash memory and flash memory R versions.
Reading the corresponding address in a mask ROM version will always return
1s, and writes to this address are disabled.
Fix the FWE pin low in mode 6.
Rev. 3.00 Sep 14, 2005 page 786 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
FLMCR (FLMCR2)—Flash Memory Control Register 2
Bit
H'EE031
Flash Memory
7
6
5
4
3
2
1
0
FLER
—
—
—
—
—
—
—
Initial value
0
0
0
0
0
0
0
0
Read/Write
R
—
—
—
—
—
—
—
Flash memory error
Reserved bits
Note: Writes to FLMCR2 are prohibited.
Rev. 3.00 Sep 14, 2005 page 787 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
EBR (EBR1)—Erase Block Register
Bit
H'EE032
Flash Memory
7
6
5
4
3
2
1
0
EB7
EB6
EB5
EB4
EB3
EB2
EB1
EB0
Modes 1 to
4, and 6
Initial value
Read/Write
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
Modes 5
and 7
Initial value
Read/Write
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Block 7 to 0
0
Block EB7 to EB0 is not selected (Initial value)
1
Block EB7 to EB0 is selected
Note: When not erasing, clear EBR to H'00.
Writes are invalid.
A value of 1 cannot be set in this register in mode 6.
Rev. 3.00 Sep 14, 2005 page 788 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
EBR (EBR2)—Erase Block Register 2
Bit
H'EE033
Flash Memory
7
6
5
4
3
2
1
0
—
—
EB13
EB12
EB11
EB10
EB9
EB8
Modes 1 to
4, and 6
Initial value
Read/Write
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
Modes 5
and 7
Initial value
Read/Write
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Block 13 to 8
0
Block EB13 to EB8 is not selected (Initial value)
1
Block EB13 to EB8 is selected
Note: When not erasing, clear EBR to H'00.
A value of 1 cannot be set in this register in mode 6.
Rev. 3.00 Sep 14, 2005 page 789 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
P2PCR—Port 2 Input Pull-Up Control Register
Bit
7
6
5
H'EE03C
4
3
2
Port 2
1
0
P27PCR P26PCR P25PCR P24PCR P23PCR P22PCR P21PCR P20PCR
Initial value
Read/Write
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Port 2 input pull-up control 7 to 0
0
Input pull-up transistor is off
1
Input pull-up transistor is on
Note: Valid when the corresponding P2DDR bit is cleared to 0
(designating generic input).
Rev. 3.00 Sep 14, 2005 page 790 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
P4PCR—Port 4 Input Pull-Up Control Register
Bit
7
6
5
H'EE03E
4
3
Port 4
2
1
0
P47PCR P46PCR P45PCR P44PCR P43PCR P42PCR P41PCR P40PCR
Initial value
Read/Write
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Port 4 input pull-up control 7 to 0
0
Input pull-up transistor is off
1
Input pull-up transistor is on
Note: Valid when the corresponding P4DDR bit is cleared to 0
(designating generic input).
P5PCR—Port 5 Input Pull-Up Control Register
Bit
7
6
5
4
H'EE03F
3
2
Port 5
1
0
P53PCR P52PCR P51PCR P50PCR
Initial value
Read/Write
1
1
1
1
0
R/W
0
R/W
0
R/W
0
R/W
Port 5 input pull-up control 3 to 0
0
Input pull-up transistor is off
1
Input pull-up transistor is on
Note: Valid when the corresponding P5DDR bit is
cleared to 0 (designating generic input).
Rev. 3.00 Sep 14, 2005 page 791 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
RAM Control Register
RAMCR
Bit
H'EE077
Flash Memory
7
6
5
4
3
2
1
0
—
—
—
—
RAMS
RAM2
RAM1
RAM0
Modes
1 to 4
Initial value
R/W
1
—
1
—
1
—
1
—
0
R
0
R
0
R
0
—
Modes
5 to 7
Initial value
R/W
1
—
1
—
1
—
1
—
0
R/W*
0
R/W*
0
R/W*
0
R/W*
Reserved bits
RAM select, RAM2 to RAM0
Bit 3
Bit 2
Bit 1
Bit 0
RAMS RAM2 RAM1 RAM0
RAM Area
RAM Emulation Status
0
0/1
0/1
0/1
H'FFE000 to H'FFEFFF
Emulation
1
0
0
0
H'000000 to H'000FFF
Mapping RAM
1
H'001000 to H'001FFF
0
H'002000 to H'002FFF
1
H'003000 to H'003FFF
0
H'004000 to H'004FFF
1
H'005000 to H'005FFF
0
H'006000 to H'006FFF
1
H'007000 to H'007FFF
1
1
0
1
Note: * In mode 6 (single-chip normal mode), flash memory emulation by RAM is not
supported; these bits can be modified, but must not be set to 1.
Note: This register is used only in the flash memory and flash memory R versions.
Reading the corresponding address in a mask ROM version will always return 1s,
and writes to this address are disabled.
Rev. 3.00 Sep 14, 2005 page 792 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
MAR0A R/E/H/L—Memory Address Register 0A R/E/H/L
Bit
31
30
29
28
27
26
25
24
Initial value
Read/Write
1
1
1
1
1
1
1
1
23
H'FFF20 H'FFF21
H'FFF22 H'FFF23
22
21
Initial value
Read/Write
19
18
17
16
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
MAR0AR
Bit
20
DMAC0
15
14
13
12
11
MAR0AE
10
9
8
7
6
5
Undetermined
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
MAR0AH
MAR0AL
Source or destination address
Rev. 3.00 Sep 14, 2005 page 793 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
ETCR0A H/L—Execute Transfer Count Register 0A H/L
•
H'FFF24 H'FFF25
DMAC0
Short address mode
 I/O mode and idle mode
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Transfer counter
 Repeat mode
Bit
Initial value
Read/Write
•
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Undetermined
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
ETCR0AH
ETCR0AL
Transfer counter
Initial count
Full address mode
 Normal mode
15
Bit
Initial value
Read/Write
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
Transfer counter
 Block transfer mode
Bit
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Initial value
Undetermined
Undetermined
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
ETCR0AH
ETCR0AL
Block size counter
Initial block size
Rev. 3.00 Sep 14, 2005 page 794 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
IOAR0A—I/O Address Register 0A
Bit
Initial value
Read/Write
H'FFF26
7
6
5
R/W
R/W
R/W
4
3
Undetermined
R/W
R/W
DMAC0
2
1
0
R/W
R/W
R/W
Short address mode : source or destination address
Full address mode : not used
Rev. 3.00 Sep 14, 2005 page 795 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
DTCR0A—Data Transfer Control Register 0A
•
H'FFF27
DMAC0
Short address mode
Bit
Initial value
Read/Write
7
6
5
4
3
2
1
0
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Data transfer select
Bit 2 Bit 1 Bit 0
DTS2 DTS1 DTS0
0
0
1
0
1
0
1
1
0
1
0
1
0
1
Data Transfer Activation Source
Compare match/input capture A
interrupt from 16-bit timer channel 0
Compare match/input capture A
interrupt from 16-bit timer channel 1
Compare match/input capture A
interrupt from 16-bit timer channel 2
A/D converter conversion end interrupt
SCI0 transmit-data-empty interrupt
SCI0 receive-data-full interrupt
Transfer in full address mode
Transfer in full address mode
Data transfer interrupt enable
Interrupt requested by
0
DTE bit is disabled
Interrupt requested by
1
DTE bit is enabled
Repeat enable
RPE DTIE
Description
0
0
I/O mode
1
0 Repeat mode
1
1 Idle mode
Data transfer increment/decrement
0
1
Incremented: If DTSZ = 0, MAR is incremented by 1 after each transfer
If DTSZ = 1, MAR is incremented by 2 after each transfer
Decremented: If DTSZ = 0, MAR is decremented by 1 after each transfer
If DTSZ = 1, MAR is decremented by 2 after each transfer
Data transfer size
0
1
Byte-size transfer
Word-size transfer
Data transfer enable
0
1
Data transfer is disabled
Data transfer is enabled
Rev. 3.00 Sep 14, 2005 page 796 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
DTCR0A—Data Transfer Control Register 0A (cont)
•
H'FFF27
DMAC0
Full address mode
Bit
Initial value
Read/Write
7
6
5
4
3
2
1
0
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A
DTS1A
DTS0A
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Data transfer select 0A
0
1
Normal mode
Block transfer mode
Data transfer select 2A and 1A
Set both bits to 1
Data transfer interrupt enable
0
1
Interrupt requested by DTE bit is disabled
Interrupt requested by DTE bit is enabled
Source address increment/decrement (bit 5)
Source address increment/decrement enable (bit 4)
Bit 4
Bit 5
Increment/Decrement Enable
SAID SAIDE
0
MARA is held fixed
0
Incremented: If DTSZ = 0, MARA is incremented by 1 after each transfer
1
If DTSZ = 1, MARA is incremented by 2 after each transfer
0
MARA is held fixed
1
Decremented: If DTSZ = 0, MARA is decremented by 1 after each transfer
1
If DTSZ = 1, MARA is decremented by 2 after each transfer
Data transfer size
0
1
Byte-size transfer
Word-size transfer
Data transfer enable
0
1
Data transfer is disabled
Data transfer is enabled
Rev. 3.00 Sep 14, 2005 page 797 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
MAR0B R/E/H/L—Memory Address Register 0B R/E/H/L
Bit
31
30
29
28
27
26
25
24
Initial value
Read/Write
1
1
1
1
1
1
1
1
23
H'FFF28 H'FFF29
H'FFF2A H'FFF2B
22
21
Initial value
Read/Write
19
18
17
16
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
MAR0BR
Bit
20
DMAC0
15
14
13
12
11
MAR0BE
10
9
8
7
6
5
Undetermined
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
MAR0BH
MAR0BL
Source or destination address
Rev. 3.00 Sep 14, 2005 page 798 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
ETCR0B H/L—Execute Transfer Count Register 0B H/L
•
H'FFF2C, H'FFF2D
DMAC0
Short address mode
 I/O mode and idle mode
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Transfer counter
 Repeat mode
Bit
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Initial value
Undetermined
Undetermined
Read/Write
:
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
ETCR0BH
ETCR0BL
Transfer counter
Initial count
•
Full address mode
 Normal mode
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
Not used
 Block transfer mode
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
Block transfer counter
Rev. 3.00 Sep 14, 2005 page 799 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
IOAR0B—I/O Address Register 0B
Bit
Initial value
Read/Write
H'FFF2E
7
6
5
R/W
R/W
R/W
4
3
Undetermined
R/W
R/W
2
1
0
R/W
R/W
R/W
Short address mode : source or destination address
Full address mode
Rev. 3.00 Sep 14, 2005 page 800 of 910
REJ09B0258-0300
: not used
DMAC0
Appendix B Internal I/O Registers
DTCR0B—Data Transfer Control Register 0B
•
H'FFF2F
DMAC0
Short address mode
Bit
Initial value
Read/Write
7
6
5
4
3
2
1
0
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Data transfer select
Bit 2 Bit 1 Bit 0
DTS2 DTS1 DTS0
0
0
1
0
1
0
1
1
0
1
0
1
0
1
Data Transfer Activation Source
Compare match/input capture A interrupt
from 16-bit timer channel 0
Compare match/input capture A interrupt
from 16-bit timer channel 1
Compare match/input capture A interrupt
from 16-bit timer channel 2
A/D converter conversion end interrupt
SCI0 transmit-data-empty interrupt
SCI0 receive-data-full interrupt
Falling edge of DREQ input
Low level of DREQ input
Data transfer interrupt enable
0
1
Interrupt requested by
DTE bit is disabled
Interrupt requested by
DTE bit is enabled
Repeat enable
Description
RPE DTIE
0
0
I/O mode
1
0 Repeat mode
1
1 Idle mode
Data transfer increment/decrement
0
1
Incremented: If DTSZ = 0, MAR is incremented by 1 after each transfer
If DTSZ = 1, MAR is incremented by 2 after each transfer
Decremented: If DTSZ = 0, MAR is decremented by 1 after each transfer
If DTSZ = 1, MAR is decremented by 2 after each transfer
Data transfer size
0
1
Byte-size transfer
Word-size transfer
Data transfer enable
0
1
Data transfer is disabled
Data transfer is enabled
Rev. 3.00 Sep 14, 2005 page 801 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
DTCR0B—Data Transfer Control Register 0B (cont)
•
H'FFF2F
DMAC0
Full address mode
7
Bit
6
DTME
Initial value
Read/Write
0
R/W
0
R/W
5
4
3
2
1
0
DAID
DAIDE
TMS
DTS2B
DTS1B
DTS0B
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Data transfer select 2B to 0B
Data transfer master enable
0
1
Bit 2 Bit 1 Bit 0
DTS2B DTS1B DTS0B
Data transfer is disabled
Data transfer is enabled
Data Transfer Activation Source
Normal Mode
Block Transfer Mode
Auto-request
(burst mode)
Compare match/input
capture A interrupt from
16-bit timer channel 0
Not available
Compare match/input
capture A interrupt from
16-bit timer channel 1
0
Auto-request
(cycle-steal mode)
Compare match/input
capture A interrupt from
16-bit timer channel 2
1
Not available
0
1
Not available
Not available
Falling edge input of
DREQ
Low level input at DREQ
0
0
1
0
1
0
1
1
0
1
A/D converter conversion
end interrupt
Not available
Not available
Falling edge input of
DREQ
Not available
Transfer mode select
0
1
Destination is the block area in block transfer mode
Source is the block area in block transfer mode
Destination address increment/decrement (bit 5)
Destination address increment/decrement enable (bit 4)
Bit 5
Bit 4
Increment/Decrement Enable
DAID DAIDE
0
MARB is held fixed
0
Incremented: If DTSZ = 0, MARB is incremented by 1 after each transfer
1
If DTSZ = 1, MARB is incremented by 2 after each transfer
0
MARB is held fixed
1
Decremented: If DTSZ = 0, MARB is decremented by 1 after each transfer
1
If DTSZ = 1, MARB is decremented by 2 after each transfer
Rev. 3.00 Sep 14, 2005 page 802 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
MAR1A R/E/H/L—Memory Address Register 1A R/E/H/L
Bit
31
30
29
28
27
26
25
24
Initial value
Read/Write
1
1
1
1
1
1
1
1
23
H'FFF30 H'FFF31
H'FFF32 H'FFF33
22
21
Initial value
Read/Write
19
18
17
16
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
MAR1AR
Bit
20
DMAC1
15
14
13
12
11
MAR1AE
10
9
8
7
6
5
4
Undetermined
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
MAR1AH
MAR1AL
Note: Bit functions are the same as for DMAC0.
ETCR1A H/L—Execute Transfer Count Register 1A H/L
Bit
Initial value
Read/Write
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
H'FFF34 H'FFF35
6
5
4
3
DMAC1
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Undetermined
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
ETCR1AH
ETCR1AL
Note: Bit functions are the same as for DMAC0.
Rev. 3.00 Sep 14, 2005 page 803 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
IOAR1A—I/O Address Register 1A
Bit
Initial value
Read/Write
H'FFF36
7
6
5
R/W
R/W
R/W
4
3
Undetermined
R/W
R/W
DMAC1
2
1
0
R/W
R/W
R/W
Note: Bit functions are the same as for DMAC0.
DTCR1A—Data Transfer Control Register 1A
•
DMAC1
Short address mode
Bit
Initial value
Read/Write
•
H'FFF37
7
6
5
4
3
2
1
0
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
7
6
5
4
3
2
1
0
DTE
DTSZ
SAID
SAIDE
DTIE
DTS2A
DTS1A
DTS0A
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Full address mode
Bit
Initial value
Read/Write
Note: Bit functions are the same as for DMAC0.
Rev. 3.00 Sep 14, 2005 page 804 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
MAR1B R/E/H/L—Memory Address Register 1B R/E/H/L
Bit
31
30
29
28
27
26
25
24
Initial value
Read/Write
1
1
1
1
1
1
1
1
23
H'FFF38 H'FFF39
H'FFF3A H'FFF3B
22
21
Initial value
Read/Write
19
18
17
16
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
MAR1BR
Bit
20
DMAC1
15
14
13
12
11
MAR1BE
10
9
8
7
6
5
4
Undetermined
3
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
MAR1BH
MAR1BL
Note: Bit functions are the same as for DMAC0.
ETCR1B H/L—Execute Transfer Count Register 1B H/L
Bit
Initial value
Read/Write
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
H'FFF3C H'FFF3D
6
5
4
3
DMAC1
2
1
0
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Undetermined
Undetermined
R/W R/W R/W R/W R/W R/W R/W R/W
R/W R/W R/W R/W R/W R/W R/W R/W
ETCR1BH
ETCR1BL
Note: Bit functions are the same as for DMAC0.
Rev. 3.00 Sep 14, 2005 page 805 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
IOAR1B—I/O Address Register 1B
Bit
Initial value
Read/Write
H'FFF3E
7
6
5
R/W
R/W
R/W
4
3
Undetermined
R/W
R/W
DMAC1
2
1
0
R/W
R/W
R/W
Note: Bit functions are the same as for DMAC0.
DTCR1B—Data Transfer Control Register 1B
•
DMAC1
Short address mode
Bit
Initial value
Read/Write
•
H'FFF3F
7
6
5
4
3
2
1
0
DTE
DTSZ
DTID
RPE
DTIE
DTS2
DTS1
DTS0
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
6
5
4
3
2
1
0
DAID
DAIDE
TMS
DTS2B
DTS1B
DTS0B
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Full address mode
Bit
7
DTME
Initial value
Read/Write
0
R/W
0
R/W
Note: Bit functions are the same as for DMAC0.
Rev. 3.00 Sep 14, 2005 page 806 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TSTR—Timer Start Register
Bit
H'FFF60
16-bit timer (all channels)
7
6
5
4
3
2
1
0
—
—
—
—
—
STR2
STR1
STR0
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Reserved bits
Counter start 0
0
TCNT0 is halted
1
TCNT0 is counting
(Initial value)
Counter start 1
0
TCNT1 is halted
1
TCNT1 is counting
(Initial value)
Counter start 2
0
TCNT2 is halted
1
TCNT2 is counting
(Initial value)
Rev. 3.00 Sep 14, 2005 page 807 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TSNC—Timer Synchro Register
Bit
H'FFF61
16-bit timer (all channels)
2
1
0
7
6
5
4
3
—
—
—
—
—
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
SYNC2 SYNC1 SYNC0
Reserved bits
Timer synchronization 0
0
Channel 0 timer counter (TCNT0) operates
independently (TCNT0 presetting/clearing is
unrelated to other channels)
(Initial value)
1
Channel 0 operates synchronously
TCNT0 synchronous presetting/synchronous
clearing is possible
Timer synchronization 1
0
Channel 1 timer counter (TCNT1) operates
independently (TCNT1 presetting/clearing is
unrelated to other channels)
(Initial value)
1
Channel 1 operates synchronously
TCNT1 synchronous presetting/synchronous
clearing is possible
Timer synchronization 2
0
Channel 2 timer counter (TCNT2) operates
independently (TCNT2 presetting/clearing is
unrelated to other channels)
(Initial value)
1
Channel 2 operates synchronously
TCNT2 synchronous presetting/synchronous
clearing is possible
Rev. 3.00 Sep 14, 2005 page 808 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TMDR—Timer Mode Register
H'FFF62
16-bit timer (all channels)
7
6
5
4
3
2
1
0
—
MDF
FDIR
—
—
PWM2
PWM1
PWM0
Initial value
1
0
0
1
1
0
0
0
Read/Write
—
R/W
R/W
—
—
R/W
R/W
R/W
Bit
PWM mode 0
0
Channel 0 operates normally (Initial value)
1
Channel 0 operates in PWM mode
PWM mode 1
0
Channel 1 operates normally (Initial value)
1
Channel 1 operates in PWM mode
PWM mode 2
0
Channel 2 operates normally (Initial value)
1
Channel 2 operates in PWM mode
Flag direction
0
1
OVF is set to 1 in TISRC when TCNT2
overflows or underflows (Initial value)
OVF is set to 1 in TISRC when TCNT2
overflows
Phase counting mode flag
0
Channel 2 operates normally
(Initial value)
1
Channel 2 operates in phase counting mode
Rev. 3.00 Sep 14, 2005 page 809 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TOLR—Timer Output Level Setting Register
H'FFF63
16-bit timer (all channels)
7
6
5
4
3
2
1
0
—
—
TOB2
TOA2
TOB1
TOA1
TOB0
TOA0
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
W
W
W
W
W
W
Bit
Output level setting A0
0
TIOCA0 is 0
1
TIOCA0 is 1
(Initial value)
Output level setting B0
0
TIOCB0 is 0
1
TIOCB0 is 1
(Initial value)
Output level setting A1
0
TIOCA1 is 0
1
TIOCA1 is 1
(Initial value)
Output level setting B1
0
TIOCB1 is 0
1
TIOCB1 is 1
(Initial value)
Output level setting A2
0
TIOCA2 is 0
1
TIOCA2 is 1
(Initial value)
Output level setting B2
0
TIOCB2 is 0
1
TIOCB2 is 1
Rev. 3.00 Sep 14, 2005 page 810 of 910
REJ09B0258-0300
(Initial value)
Appendix B Internal I/O Registers
TISRA—Timer Interrupt Status Register A
Bit:
7
—
6
H'FFF64
5
4
IMIEA2 IMIEA1 IMIEA0
3
16-bit timer (all channels)
2
1
0
—
IMFA2 IMFA1 IMFA0
0
0
0
R/(W)* R/(W)* R/(W)*
Initial value:
1
0
0
0
1
Read/Write:
—
R/W
R/W
R/W
—
Input capture/compare match flag A0
[Clearing conditions]
0
(Initial value)
Read IMFA0 when IMFA0=1, then write 0 in IMFA0
DMAC activated by IMIA0 interrupt.
[Setting conditions]
TCNT0=GRA0 when GRA0 functions as an output compare register.
1
TCNT0 value is transferred to GRA0 by an input capture signal when GRA0
functions as an input capture register.
Input capture/compare match flag A1
[Clearing conditions]
0
(Initial value)
Read IMFA1 when IMFA1=1, then write 0 in IMFA1
DMAC activated by IMIA1 interrupt.
[Setting conditions]
TCNT1=GRA1 when GRA1 functions as an output compare register.
1
TCNT1 value is transferred to GRA1 by an input capture signal when GRA1
functions as an input capture register.
Input capture/compare match flag A2
[Clearing conditions]
0
(Initial value)
Read IMFA2 when IMFA2=1, then write 0 in IMFA2
DMAC activated by IMIA2 interrupt.
[Setting conditions]
TCNT2=GRA2 when GRA2 functions as an output compare register.
1
TCNT2 value is transferred to GRA2 by an input capture signal when GRA2
functions as an input capture register.
Input capture/compare match interrupt enable A0
0
IMIA0 interrupt requested by IMFA0 flag is disabled
1
Input capture/compare match interrupt enable A1
0
IMIA1 interrupt requested by IMFA1 flag is disabled
1
(Initial value)
IMIA1 interrupt requested by IMFA1 is enabled
Input capture/compare match interrupt enable A2
0
IMIA2 interrupt requested by IMFA2 flag is disabled
1
(Initial value)
IMIA0 interrupt requested by IMFA0 is enabled
(Initial value)
IMIA2 interrupt requested by IMFA2 is enabled
Note: * Only 0 can be written, to clear the flag.
Rev. 3.00 Sep 14, 2005 page 811 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TISRB—Timer Interrupt Status Register B
Bit:
7
—
6
H'FFF65
5
4
IMIEB2 IMIEB1 IMIEB0
3
16-bit timer (all channels)
2
1
0
—
IMFB2 IMFB1 IMFB0
0
0
0
R/(W)* R/(W)* R/(W)*
Initial value:
1
0
0
0
1
Read/Write:
—
R/W
R/W
R/W
—
Input capture/compare match flag B0
0
[Clearing condition]
(Initial value)
Read IMFB0 when IMFB0=1, then write 0 in IMFB0.
[Setting conditions]
TCNT0=GRB0 when GRB0 functions as an output compare register.
1
TCNT0 value is transferred to GRB0 by an input capture signal when GRB0
functions as an input capture register.
Input capture/compare match flag B1
0
[Clearing condition]
(Initial value)
Read IMFB1 when IMFB1=1, then write 0 in IMFB1.
[Setting conditions]
TCNT1=GRB1 when GRB1 functions as an output compare register.
1
TCNT1 value is transferred to GRB1 by an input capture signal when GRB1
functions as an input capture register.
Input capture/compare match flag B2
0
[Clearing condition]
(Initial value)
Read IMFB2 when IMFB2=1, then write 0 in IMFB2.
[Setting conditions]
TCNT2=GRB2 when GRB2 functions as an output compare register.
1
TCNT2 value is transferred to GRB2 by an input capture signal when GRB2
functions as an input capture register.
Input capture/compare match interrupt enable B0
0
IMIB0 interrupt requested by IMFB0 flag is disabled
1
Input capture/compare match interrupt enable B1
0
IMIB1 interrupt requested by IMFB1 flag is disabled
1
(Initial value)
IMIB1 interrupt requested by IMFB1 is enabled
Input capture/compare match interrupt enable B2
0
IMIB2 interrupt requested by IMFB2 flag is disabled
1
(Initial value)
IMIB0 interrupt requested by IMFB0 is enabled
IMIB2 interrupt requested by IMFB2 is enabled
Note: * Only 0 can be written, to clear the flag.
Rev. 3.00 Sep 14, 2005 page 812 of 910
REJ09B0258-0300
(Initial value)
Appendix B Internal I/O Registers
TISRC—Timer Interrupt Status Register C
7
Bit:
—
6
5
H'FFF66
4
OVIE2 OVIE1 OVIE0
3
16-bit timer (all channels)
2
1
0
—
OVF2 OVF1 OVF0
0
0
0
R/(W)* R/(W)* R/(W)*
Initial value:
1
0
0
0
1
Read/Write:
—
R/W
R/W
R/W
—
Overflow flag 0
0
1
[Clearing condition]
(Initial value)
Read OVF0 when OVF0 = 1, then write 0 in OVF0.
[Setting condition]
TCNT0 overflowed from H'FFFF to H'0000.
Overflow flag 1
0
[Clearing condition]
Read OVF1 when OVF1 = 1, then write 0 in OVF1.
1
[Setting condition]
TCNT1 overflowed from H'FFFF to H'0000.
(Initial value)
Overflow flag 2
0
[Clearing condition]
Read OVF2 when OVF2 = 1, then write 0 in OVF2.
1
[Setting condition]
TCNT2 overflowed from H'FFFF to H'0000, or underflowed from H'0000
to H'FFFF.
Overflow interrupt enable 0
OVI0 interrupt requested by OVF0 flag is disabled
0
1
(Initial value)
OVI1 interrupt requested by OVF1 flag is enabled
Overflow interrupt enable 2
OVI2 interrupt requested by OVF2 flag is disabled
0
1
(Initial value)
OVI0 interrupt requested by OVF0 flag is enabled
Overflow interrupt enable 1
OVI1 interrupt requested by OVF1 flag is disabled
0
1
(Initial value)
(Initial value)
OVI2 interrupt requested by OVF2 flag is enabled
Note: * Only 0 can be written, to clear the flag.
Rev. 3.00 Sep 14, 2005 page 813 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TCR0—Timer Control Register
Bit
Initial value
Read/Write
H'FFF68
7
—
6
5
4
3
2
1
0
CCLR1
CCLR0
CKEG1
CKEG0
TPSC2
TPSC1
TPSC0
1
—
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
Timer prescaler 2 to 0
Bit 1
Bit 0
Bit 2
TPSC2
TPSC1
0
1
0
1
1
Clock edge 1 and 0
Bit 4
Bit 3
CKEG1
CKEG0
0
0
1
0
1
—
Rising edges counted
Falling edges counted
Both edges counted
1
1
(Initial value)
TCNT clear Sources
CCLR0
0
1
0
Internal clock : φ
Internal clock : φ / 2
Internal clock : φ / 4
Internal clock : φ / 8
External clock A : TCLKA input
External clock B : TCLKB input
External clock C : TCLKC input
External clock D : TCLKD input
0
1
0
1
0
1
0
1
Counted Edges of External Clock
Counter clear 1 and 0
Bit 6
Bit 5
0
TCNT Clock Source
TPSC0
0
CCLR1
16-bit timer channel 0
(Initial value)
TCNT is not cleared
TCNT is cleared by GRA compare match or input capture
TCNT is cleared by GRB compare match or input capture
Synchronous clear : TCNT is cleared in synchronization with other
synchronized timers
Rev. 3.00 Sep 14, 2005 page 814 of 910
REJ09B0258-0300
(Initial value)
Appendix B Internal I/O Registers
TIOR0—Timer I/O Control Register 0
Bit:
H'FFF69
16-bit timer channel 0
7
6
5
4
3
2
1
0
IOA0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
Initial value:
1
0
0
0
1
0
0
0
Read/Write:
—
R/W
R/W
R/W
—
R/W
R/W
R/W
I/O control A2 to A0
Bit 2
Bit 1
IOA2
IOA1
0
0
1
0
1
0
1
1
1
0
0
1
0
1
1
GRA Functions
GRA is an output
compare register
1
0
I/O control B2 to B0
Bit 6
Bit 5
IOB2
IOB1
Bit 0
IOA0
0
1
0
Bit 4
IOB0
0
1
0
GRA is an input
capture register
(Initial value)
0 output at GRA compare match
1 output at GRA compare match
Output toggles at GRA compare match
(channel 2 only: 1 output)
GRA captures rising edges of input
GRA captures falling edges of input
GRA captures both edges of input
GRB Functions
GRB is an output
compare register
1
0
1
0
1
No output at compare match
GRB is an input
capture register
No output at compare match
(Initial value)
0 output at GRB compare match
1 output at GRB compare match
Output toggles at GRB compare match
(channel 2 only: 1 output)
GRB captures rising edges of input
GRB captures falling edges of input
GRB captures both edges of input
Rev. 3.00 Sep 14, 2005 page 815 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TCNT0 H/L—Timer Counter 0 H/L
Bit
Initial value
Read/Write
15
14
13
12
11
H'FFF6A, H'FFF6B
10
9
8
7
6
5
16-bit timer channel 0
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Up - counter
GRA0 H/L—General Register A0 H/L
Bit
Initial value
Read/Write
15
14
13
12
11
H'FFF6C, H'FFF6D
10
9
8
7
6
5
16-bit timer channel 0
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Output compare or input capture register
GRB0 H/L—General Register B0 H/L
Bit
Initial value
Read/Write
15
14
13
12
11
H'FFF6E, H'FFF6F
10
9
8
7
6
5
16-bit timer channel 0
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Output compare or input capture register
Rev. 3.00 Sep 14, 2005 page 816 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
TCR1 Timer Control Register 1
7
Bit
H'FFF70
6
—
5
4
16-bit timer channel 1
3
2
1
0
CCLR1 CCLR0 CKEG1 CKEG0 TPSC2 TPSC1 TPSC0
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Note: Bit functions are the same as for 16-bit timer channel 0.
TIOR1—Timer I/O Control Register 1
H'FFF71
16-bit timer channel 1
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
Bit
Note: Bit functions are the same as for 16-bit timer channel 0.
TCNT1 H/L—Timer Counter 1 H/L
Bit
Initial value
Read/Write
15
14
13
12
11
H'FFF72, H'FFF73
10
9
8
7
6
5
16-bit timer channel 1
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for 16-bit timer channel 0.
Rev. 3.00 Sep 14, 2005 page 817 of 910
REJ09B0258-0300
Appendix B Internal I/O Registers
GRA1 H/L—General Register A1 H/L
Bit
Initial value
Read/Write
15
Similar pages