ETC1 HB16SKW01-6GJB Distinctive characteristic Datasheet

Subminiature Pushbuttons
Series HB
Distinctive Characteristics
Full face and spot illumination available. Front panel relamping.
Choice of super bright LEDs in white, green, and blue in
addition to bright red, amber, and green LEDs.
Compact front panel design with 9mm square or round
bezel options.
Rear panel threaded mounting. Behind panel depth
of less than one inch. 8mm body diameter
fits common size panel cutout.
Latchdown feature gives indication of circuit status.
Audible and tactile feedback with smooth and
responsive operation.
Dual, sliding contacts with self-cleaning action provide
contact stability, high reliability, and increased
operating life.
Solder lug terminals have spacing of .100” (2.54mm) for choice
of mounting.
Longer normally closed terminal facilitates wiring and soldering.
Molded-in terminals lock out flux, dust, and other contaminants.
Nonilluminated models available.
Matching indicators available.
Actual Size
NKK Switches • email: [email protected] • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
3-05
Subminiature Pushbuttons
Series HB
General Specifications
Electrical Capacity (Resistive Load)
Power Level (code W):
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel:
Materials & Finishes
Housing:
Base:
Movable Contact:
Stationary Contacts:
Common Terminal:
End Terminals:
Lamp Terminals:
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
Installation
Mounting Torque:
Cap Installation Force:
Soldering Time & Temperature:
Standards & Certifications
R
R
UL & C-UL
Recognized:
0.1A maximum @ 30V AC/DC
50 milliohms maximum
100 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum
50,000 operations minimum
3.43N
Nonshorting (break before make)
Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm)
Glass fiber reinforced polyamide
Glass fiber reinforced polyamide
Phosphor bronze with silver plating
Phosphor bronze with silver plating
Phosphor bronze with silver plating
Phosphor bronze with silver plating
Phosphor bronze with silver plating
–25°C through +50°C (–13°F through +122°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
0.49Nm (4.34 lb • in) maximum for round mounting nut
9.8N (2.2 lbf) maximum downward force on cap
4 seconds maximum @ 390°C maximum for manual soldering
Note: Find additional processing data in Supplement section.
All models recognized at 0.1A @ 30V AC/DC;
UL File No. WOYR2.E44145;
add “/U” to end of part number to order UL mark on switch.
C-UL File No. WOYR8.E44145;
add “/UC” to end of part number to order C-UL mark on switch.
NKK Switches • email: [email protected] • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
3-05
Subminiature Pushbuttons
Series HB
TYPICAL SWITCH ORDERING EXAMPLE
HB
1
5
S
K
W01
6G
JB
POLE
1
SPDT
HOUSING
K
Black only
CIRCUITS
5
ON
(ON)
CONTACTS & TERMINALS
( ) = Momentary
6
ON
Silver Contacts and
W01 Solder Lug Terminals
0.1A @ 30V AC/DC
ON
Alternate Action
with Latchdown
SHAPES
S
Square
C
Round
LEDS
CAP TYPES & COLORS
Bright
LED Cap: Lens/Diffuser Color
5C
Red
5D
Amber
5F
Green
IMPORTANT:
Switches are supplied without UL
& C-UL markings unless specified.
Specific models & ratings noted on
General Specifications page.
AB
Black Cap/White Window for
Spot Illuminaterd (Square only)
CB
Red/White
DB
Amber/White
FB
Green/White
JB
Clear/White
Super Bright
6B
White
6F
Green
6G
Blue
LED Cap: Lens/Diffuser Color
JB
Clear/White
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
HB15SKW01-6G-JB
Blue, Super Bright LED
White Cap
Square Shape
Black Housing
SPDT ON-(ON) Circuit
Silver Contacts and Solder Lug Terminals;
rated 0.1A @ 30V AC/DC
NKK Switches • email: [email protected] • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
3-05
Subminiature Pushbuttons
Series HB
POLES & CIRCUITS
Plunger Position
( ) = Momentary
Pole
Model
SP
HB15
*HB16
Connected Terminals
Throw & Switch/Lamp Schematics
Normal
Down
Normal
Down
Notes:
ON
ON
(ON)
ON
1-3
1-2
SPDT
Switch is marked with NO, NC, C, L.
LED circuit is isolated and requires
external power source.
1 (COM)
(+)
3
(-)
2
* When in latchdown position for the alternate circuit, cap position is .051” (1.3mm) above the built-in bezel.
SHAPES
S
C
.354” (9mm) Square
The bezel is an integral
part of the switch body.
.354” (9mm) Round
The bezel is an integral
part of the switch body.
Panel Cutout & Mounting
Recommended Panel Thickness:
.020 ~ .197” (0.5 ~ 5.0mm)
(8.0) Dia
.315
Overtightening the mounting nut AT073
may damage the switch housing.
HOUSING
K
Housing available in black only.
CONTACT MATERIALS, RATINGS, & TERMINALS
W01
Silver Contacts
Power Level
0.1A maximum @ 30V AC/DC
Solder Lug
The .039” x .079” (1.0mm x 2.0mm)
oblong hole accommodates one solid
or one stranded 20-gauge wire or two
22-gauge wires.
PCB Mounting
(5.0)
.197
(2.0)
.079
(1.0)
.039
(1.8)
.071
Thk = (0.3)
.012
Solder lug terminals are spaced
.100” x .200” (2.54mm x 5.08mm).
This enables PCB mounting which can be
accomplished by elongating PC board
holes to .080” (2.03mm).
NKK Switches • email: [email protected] • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
3-05
Series HB
Subminiature Pushbuttons
LED COLORS & SPECIFICATIONS
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Single element LED is colored in OFF state.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Bright
AT633
AT629B
White
AT630F
Green
T-1 Bi-pin
Electrostatic
Sensitive Devices
Super Bright
5C
5D
5F
6B
6F
6G
Color
Red
Amber
Green
White
Green
Blue
Unit
Forward Peak Current
IFM
30
30
25
30
30
30
mA
Continuous Forward Current
IF
20
20
20
20
20
20
mA
Forward Voltage
VF
1.85
2.0
2.2
3.6
3.5
3.6
V
Reverse Peak Voltage
VRM
5
5
5
5
5
5
V
Current Reduction Rate Above 25°C
∆IF
0.40
0.42
0.38
0.50
0.50
0.50
mA/°C
(+)
Super Bright
AT624G
Blue
Bright
Attention
Note for Super Bright:
(-)
Ambient Temperature Range
–25° ~ +50°C
–25° ~ +50°C
CAP TYPES & COLORS
Color Codes:
A Black
B White
C Red
D Amber
F Green
J Clear
Colored Cap for Bright LEDs
Cap Colors Available:
AB
(7.4) Sq
.291
AT4052
Spot Illuminated
Black Cap with Translucent
White Window for LED Display
(4.8)
.189
(4.6)
.181
(1.8)
.071
(1.2)
.047
(3.0)
.118
Square only
Material: Polycarbonate
Finish: Matte
Lens/Diffuser
Colors Available:
CB
AT4166
Square
Amber/White
FB
Green/White
(4.5)
.177
(4.8)
.189
Transparent Colored
Lens
(7.4) Dia
.291
(7.4) Sq
.291
Red/White
DB
AT4167
Round
(4.5)
.177
(4.8)
.189
Material: Polycarbonate
Translucent
White Diffuser
Colored LED
AT633
Finish: Glossy
White Cap for Bright & Super Bright LEDs
JB
Clear Lens/
White Diffuser
AT4031
Square
Material: Polycarbonate
Finish: Glossy
(7.4) Dia
.291
(7.4) Sq
.291
(4.5)
.177
(4.8)
.189
Transparent Clear
Lens
AT4032
Round
(4.5)
.177
(4.8)
.189
Translucent
White Diffuser
Colored LEDs
AT624, AT629,
AT630, or AT633
NKK Switches • email: [email protected] • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
3-05
Subminiature Pushbuttons
Series HB
TYPICAL SWITCH DIMENSIONS
Square
Single Pole
(1.0) x (2.0) Typ
.039 x .079
(0.3) Typ
.012
M8P0.75
L(+) L(-)
NO
NC
(7.4) Sq
.291
(9.0) Sq
.354
(1.3)
.051
(3.5)
.138
(0.5)
(5.0)
.020
.197
(10.0)
.394
(15.5)
(5.3)
.610
.209
COM
(1.8)
.071
(2.54) Typ
.100
2
3
1
(5.0)
.197
(7.0)
.276
(2.54) Typ
.100
Latchdown Position
HB15SKW01-5C-CB
Round
Single Pole
M8P0.75
(1.0) x (2.0) Typ
.039 x .079
(0.3) Typ
.012
L(+) L(-)
NO
NC
(7.4) Dia
.291
(9.0) Dia
.354
(1.3)
.051
(3.5)
.138
(5.0)
(0.5)
.197
.020
(10.0)
.394
(5.3)
(15.5)
.209
.610
COM
(1.8)
.071
(5.0)
.197
(7.0)
.276
2
(2.54) Typ
.100
3
1
(2.54) Typ
.100
Latchdown Position
HB16CKW01-5C-CB
ASSEMBLY INSTRUCTIONS
Cap Removal
LED Polarity & Orientation in Lamp Socket
Cap Replacement
1. Have cap in extended
position (not latchdown) for
alternate action models.
For AT624, AT629, AT630: Insert the LED with the
D flat opposite the black dot molded inside the
switch lamp socket. For AT633: Insert the LED with
the Black Dot on the terminal to the right.
1. Match the prongs on
the cap base with the
projections in the switch,
at the same time ligning
the spring clips on the
cap with the indentations
in the switch.
2. Use the grip slots on the
sides of the cap and pull it
out of the switch.
Black Dot
D Flat
AT624
AT629
AT630
(+)
(–)
(+)
(–)
AT633
2. Press firmly in place.
Top View
of Switch
Anode
(+)
Attention
Electrostatic
Sensitive Devices
Cathode
(–)
Super Bright LEDs AT624, AT629,
& AT630 are electrostatic sensitive.
AT111 Lamping Tool
AT110 Socket Wrench
Lamping Tool AT111 may be
used to remove and replace LED.
Socket Wrench AT110 may be
used to tighten the mounting nut.
NKK Switches • email: [email protected] • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
3-05
Similar pages