Dc HBL2G Technical specifications of single-phase silicon bridge rectifier Datasheet

HBL2A
DC COMPONENTS CO., LTD.
R
THRU
RECTIFIER SPECIALISTS
HBL2M
TECHNICAL SPECIFICATIONS OF SINGLE-PHASE SILICON BRIDGE RECTIFIER
VOLTAGE RANGE - 50 to 1000 Volts
CURRENT - 2.0 Amperes
FEATURES
* Ideal for printed circuit board
* Surge overload rating: 50 Amperes peak
HBL
Case: Molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: MIL-STD-202E, Method 208 guaranteed
Polarity: Symbols molded or marked on body
Mounting position: Any
.187(4.7)
.148(3.8)
.44(11.2)
.42(10.7)
AC
.080(2.0)
.065(1.7)
.060(1.5)
.045(1.1)
.095(2.4)
.065(1.6)
.68(17.3)
.62(15.7)
*
*
*
*
*
.81(20.6)
.77(19.6)
.125(3.2)
o
45
Chamfer
MECHANICAL DATA
.045(1.1)
.035(0.9)
.020(0.5)
.015(0.4)
.209(5.3)
SPACING
.189(4.8)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 o C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Dimensions in inches and (millimeters)
SYMBOL
HBL2A
HBL2B
HBL2D
HBL2G
HBL2J
HBL2K
HBL2M
UNITS
Maximum Recurrent Peak Reverse Voltage
VRRM
50
100
200
400
600
800
1000
Volts
Maximum RMS Bridge Input Voltage
VRMS
35
70
140
280
420
560
700
Volts
VDC
50
100
200
400
600
800
1000
Maximum DC Blocking Voltage
o
Maximum Average Forward Output Current at TA = 50 C
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC Method)
Maximum Forward Voltage Drop per element at 1.0A DC
Maximum DC Reverse Current at Rated
@T A = 25 oC
DC Blocking Voltage per element
@T A = 100 oC
2
I t Rating for Fusing (t*8.3ms)
Typical Junction Capacitance ( Note1)
Typical Thermal Resistance (Note 2)
Operating Temperature Range
Storage Temperature Range
Volts
IO
2.0
Amps
I FSM
50
Amps
VF
1.0
Volts
IR
10
500
2
I t
93
CJ
40
Rθ J A
19
µAmps
A 2 Sec
pF
0
C/W
TJ
-55 to +150
0
C
TSTG
-55 to +150
0
C
NOTES : 1.Measured at 1 MHZ and applied reverse voltage of 4.0 volts
2.Thermal Resistance from Junction to Case per element Unit mounted on 300x300x1.6mm Aluminum plate heat-sink.
RATING AND CHARACTERISTIC CURVES (HBL2A THRU HBL2M)
300
250
8.3ms Single Half Sine-Wave
(JEDEC Mathod)
200
150
100
50
0
1
2
5
10
20
50
100
FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE
AVERAGE FORWARD OUTPUT CURRENT, (A)
PEAK FORWARD SURGE CURRENT, (A)
FIG. 1 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT
5
4
3
2
Single Phase Half Wave
60Hz Inductive or
Resistive Load
1
0
50
TJ=25oC
10
Pulse Width=300ms
1% Duty Cycle
1
.6
.8
1.0
1.2
1.4
1.6
1.8
INSTANTANEOUS FORWARD VOLTAGE, (V)
2.0
10
TJ=100oC
1.0
.1
TJ=25oC
.01
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE, (%)
DC COMPONENTS CO., LTD.
R
150
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT, (µA)
INSTANTANEOUS FORWARD CURRENT, (A)
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS
100
.1
100
CASE TEMPERATURE, (oC)
NUMBER OF CYCLES AT 60Hz
Similar pages