AVAGO HDSP-315G 10 mm and 13 mm slim font seven segment display Datasheet

HDSP-315x/316x/515x/516x Series
10 mm and 13 mm Slim Font Seven Segment Displays
Data Sheet
Description
Features
The HDSP-31xx-51xx Series of displays incorporates a new
slim font character design. This slim font features narrow
width, specially mitered segments to give a fuller appearance to the illuminated character. Faces of these displays
are painted a neutral gray for enhanced on/off contrast.
• Excellent appearance
All devices are available in either common anode or
common cathode configuration with right hand decimal
point. Low current versions are available in either AlGaAs
red or HER.
• Choice of colors: DH AlGaAs red, High Efficiency Red
(HER), yellow, and green
• Slim font design
• Mitered corners, evenly illuminated segments
• Gray face for optimum on/off contrast
• Low current available, AlGaAs red and HER choice of
character size: 10 mm and 13 mm
• ±50° viewing angle
• Characterized for luminous intensity
Devices
AlGaAs
Red Low
Current
HDSP-
HER
Std.
Current
HDSP-
HER
Low
Current
HDSP-
Yellow
Std.
Current
HDSP-
Green
Std.
Current
HDSPDescription
Package
Drawing
315H
315E
315L
315Y
315G
Common Anode,
10 mm Display
A
316H
316E
316L
316Y
316G
Common Cathode,
10 mm Display
B
515H
515E
515L
515Y
515G
Common Anode,
13 mm Display
A
516H
516E
516L
516Y
516G
Common Cathode,
13 mm Display
B
Part Numbering System
5082 - X X X X - X X X X X
HDSP - X X X X - X X X X X
Mechanical Options[1]
00: No Mechanical Option
Color Bin Options[1,2]
0: No Color Bin Limitation
Maximum Intensity Bin[1,2]
0: No Maximum Intensity Bin Limitation
Minimum Intensity Bin[1,2]
0: No Minimum Intensity Bin Limitation
Device Configuration/Color[1]
H: AlGaAs Red
E: High Efficiency Red
G: Green
Y: Yellow
Device Specific Configuration[1]
Refer to Respective Datasheet
Package[1]
Refer to Respective Datasheet
Notes:
1. For codes not listed in the figure above, please refer to the respective datasheet or
contact your nearest Avago representative for details.
2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically
restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet
for specific bin limit information.
2
HDSP-315x/316x Series
6
COLOR BIN (NOTE 3)
0.9
2.54 ± 0.38
10
HDSP-XXXX
HP XYY ZW
10°
LUMINOUS
INTENSITY
CATEGORY
12.8
± 0.2
DIA. 1.2
4 x 2.54
0.53
± 0.05
6.4
± 0.1
7
± 0.1
9.7 ± 0.1
1
2 f
3
4
5 e
a
g
d
10
9
b 8
7
c 6
DP
PIN FUNCTION
1
g
2
f
3
Common A/C
4
e
5
d
6
DP
7
c
8
Common A/C
9
b
10 a
DATE
CODE
10.4 MIN.
0.3 ± 0.05
7.62
± 0.38
HDSP-515x/516x Series
HDSP-315X pkg dimen. (A)
LUMINOUS
INTENSITY
CATEGORY
7.40
10°
COLOR BIN (NOTE 3)
5.08
12.25 ± 0.15
17.50 + 0.3
– 0.1
DIA. 1.25
HDSP-XXXX
HP XYY ZW
13.0
DATE
CODE
6.40
± 0.1
7.00
± 0.1
1.04 ± 0.3 TYP.
2.54 ± 0.3 TYP.
Notes:
1. Package dimensions in millimeters.
2. Untoleranced dimensions are for reference only. HDSP-315X pkg dimen. (B)
3. For yellow and green devices only.
3
a
f
e
d
0.29 ± 0.08 TYP.
b
g
15.24 ± 0.3
3.60 ± 0.3
0.38 ± 0.08
10 9 8 7 6
2.54 ± 0.38
1.25
c
DP
1 2 3 4 5
PIN FUNCTION
1
e
2
d
3
Common A/C
4
c
5
DP
6
b
7
a
8
Common A/C
9
f
10
g
Absolute Maximum Ratings
AlGaAs
Red Low
Current
HER
HER
Low
Current
Yellow
Green
Units
Average Power per
Segment or DP
37
105
52
105
105
mW
Peak Forward Current
per Segment or DP
45
90[2]
45
90[5]
90[7]
mA
DC Forward Current
per Segment or DP
15[1]
30[3]
15[4]
30[6]
30[8]
mA
Operating Temperature Range
-20 to 100
Description
-40 to +100
°C
Storage Temperature Range
-40 to +100 °C
Reverse Voltage per
Segment or DP
3.0
V
Wavesoldering Temperature
for 3 seconds 1.59 mm below body
250 °C
Notes:
1. Derate above 91°C at 0.53 mA/°C.
2. See Figure 9 to establish pulsed conditions.
3. Derate above 53°C at 0.45 mA/°C.
4. Derate above 80°C at 0.38 mA/°C.
5. See Figure 10 to establish pulsed conditions.
6. Derate above 81°C at 0.52 mA/°C.
7. See Figure 11 to establish pulsed ocnditions.
8. Derate above 39°C at 0.37 mA/°C.
Electrical/Optical Characteristics at TA = 25°C
AlGaAs Red Low Current
Device Series
HDSPParameter
Symbol
Min.
Typ.
Max.
Units
315/316H
515/516H
Luminous Intensity/Segment[1,2]
(Digit Average)
IV
180
650
µcd
IF = 1 mA
V
IF = 1 mA
Forward Voltage/Segment or DP
VF
1.8
Peak Wavelength
λPEAK
645
nm
Dominant Wavelength[3]
λd
637
nm
Reverse Voltage/Segment or DP[4]
VR
15
V
Thermal Resistance LED
Junction-to-Pin
RθJ-PIN
255
°C/W/Seg
3
2.2
Test
Conditions
IR = 100 µA
HER
Device Series
HDSPParameter
Symbol
Min.
Typ.
Max.
Units
315/316E
515/516E
Luminous Intensity/Segment[1,2]
(Digit Average)
IV
Forward Voltage/Segment or DP
Test
Conditions
2600
µcd
IF = 10 mA
VF
1.9
V
IF = 10 mA
Peak Wavelength
λPEAK
635
Dominant Wavelength[3]
λd
626
nm
Reverse Voltage/Segment or DP[4]
VR
30
V
Thermal Resistance LED
Junction-to-Pin
RθJ-PIN
200
°C/W/Seg
4
450
3
2.5
nm
IR = 100 µA
HER Low Current
Device Series
HDSPParameter
Symbol
Min.
Typ.
Max.
Units
315/316L
515/516L
Luminous Intensity/Segment[1,2]
(Digit Average)
IV
Forward Voltage/Segment or DP
Peak Wavelength
Dominant Wavelength[3]
Reverse Voltage/Segment or DP[4]
Thermal Resistance LED
Junction-to-Pin
RθJ-PIN
Test
Conditions
370
µcd
IF = 2 mA
VF
2.1
V
IF = 2 mA
λPEAK
635
nm
λd
626
nm
VR
30
V
200
°C/W/Seg
180
3
2.5
IR = 100 µA
Yellow
Device Series
HDSPParameter
Symbol
Min.
Typ.
Max.
Units
315/316Y
515/516Y
Luminous Intensity/Segment[1,2]
(Digit Average)
IV
Forward Voltage/Segment or DP
Peak Wavelength
Test
Conditions
1800
µcd
IF = 10 mA
VF
2.0
V
IF = 10 mA
λPEAK
583
nm
Dominant Wavelength[3]
λd
586
nm
Reverse Voltage/Segment or DP[4]
VR
50
V
Thermal Resistance LED
Junction-to-Pin
RθJ-PIN
200
°C/W/Seg
450
3
2.5
IR = 100 µA
Green
Device Series
HDSPParameter
Symbol
Min.
Typ.
Max.
Units
315/316G
515/516G
Luminous Intensity/Segment[1,2]
(Digit Average)
IV
Forward Voltage/Segment or DP
VF
Peak Wavelength
λPEAK
566
nm
Dominant Wavelength[3]
λd
571
nm
Reverse Voltage/Segment or DP[4]
VR
50
V
Thermal Resistance LED
Junction-to-Pin
RθJ-PIN
200
°C/W/Seg
450
3
Test
Conditions
5000
µcd
IF = 10 mA
2.1
V
IF = 10 mA
2.5
IR = 100 µA
Notes:
1. Case temperature of device immediately prior to the intensity measurement is 25°C.
2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package.
3. The dominant wavelength, λ is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.
4. Typical specification for reference only. Do not exceed absolute maximum ratings.
5
50.0
20
18
16
14
12
10
8
6
4
2
0
20.0
RθJ-A = 770°C/W
IF – FORWARD CURRENT
PER SEGMENT – mA
IF AVE. MAX – MAXIMUM AVERAGE
FORWARD CURRENT PER SEGMENT – mA
AlGaAs Low Current
20
30
40
50 60 70 80 90 100 110 120
TA – AMBIENT TEMPERATURE – °C
20
RELATICE LUMINOUS INTENSITY
(NORMALIZED TO 1AT 1ma)
2.0
1.0
0.5
0.1
Figure 1. Maximum allowable average or DC current vs. ambient temperature.
10
5
2
1
0.5
0.2
0.1
0.1
0.2
1
2
5
10
0.5
IF – FORWARD CURRENT PER SEGMENT – mA
Figure 3. Relative luminous intensity vs DC forward current.
6
10.0
5.0
20
0
0.5
1.0
1.5
VF – FORWARD VOLTAGE - V
Figure 2. Forward current vs. forward voltage.
2.0
2.5
HER, Yellow, and Green
10
10000
OPERATION IN THIS
REGION REQUIRES
TEMPERATURE
DERATING OF IDC
MAXIMUM
10
1
10
z
0H
30
Hz
1K
Hz
3K
Z
KH
10
IFPEAK RATIO OF MAXIMUM OPERATING
IDC MAX PEAK CURRENT TO TEMPERATURE
DERATED DC CURRENT
100
0H
z
DC OPERATION
10
100
1000 10000
tp – PULSE DURATION – µs
Figure 6. Allowable peak current vs. pulse duration – Green.
100
80
60
YELLOW
40
HER
20
0
GREEN
2.0
3.0
4.0
VF – FORWARD VOLTAGE – V
Figure 8. Forward current vs. forward voltage characteristics.
7
0
1.0
1
z
10
100
1000
tp – PULSE DURATION – µs
50
45
40
35
30
25
20
15
10
10000
DC OPERATION
5.0
5
0
R¸ J-A = 770°C/W
GREEN
HER
YELLOW
50 60 70 80 90 100 110 120
TA – AMBIENT TEMPERATURE – °C
Figure 7. Maximum allowable DC current per segment as a function of
ambient temperature.
RELATIVE LUMINOUS INTENSITY
(NORMALIZED TO 1 AT 5 mA FOR HER AND
YELLOW AND TO 1 AT 10 mA FOR GREEN)
IF – FORWARD CURRENT PER SEGMENT – mA
1
1
0H
Figure 5. Maximum tolerable peak current vs. pulse duration – Yellow.
Figure 4. Maximum tolerable peak current vs. pulse duration – HER.
IDC MAX – MAXIMUM DC CURRENT
PER SEGMENT – mA
10
100
1000
tp – PULSE DURATION – µs
DC OPERATION
10
z
0H
30
Hz
1K
Hz
HZ
z
10
3K
0H
OPERATION IN THIS
REGION REQUIRES
TEMPERATURE
DERATING OF IDC
MAXIMUM
K
10
Z
1
z
0H
30
Hz
1K
Hz
3K
KH
1
10
100
IFPEAK RATIO OF MAXIMUM OPERATING
IDC MAX PEAK CURRENT TO TEMPERATURE
DERATED DC CURRENT
OPERATION IN THIS
REGION REQUIRES
TEMPERATURE
DERATING OF IDC
MAXIMUM
10
IFPEAK RATIO OF MAXIMUM OPERATING
IDC MAX PEAK CURRENT TO TEMPERATURE
DERATED DC CURRENT
100
20
30
40
12
10
HER
8
YELLOW
6
4
GREEN
2
0
0
15
5
10
20
25
IF – FORWARD CURRENT PER SEGMENT – mA
Figure 9. Relative luminous intensity vs. DC forward current.
30
20
18
16
14
12
10
8
6
4
2
0
20
RθJ-A = 770°C/W
HER
30
40
50 60 70 80 90 100 110 120
TA – AMBIENT TEMPERATURE – °C
RELATIVE LUMINOUS INTENSITY
(NORMALIZED TO 1 AT 2 mA FOR HER AND
TO 1 AT 4 mA FOR YELLOW AND GREEN
16
14
12
HER
8
6
4
2
0
0
2
4
6
8
10 12
14
VF – FORWARD CURRENT PER SEGMENT – mA
Figure 12. Relative luminous intensity vs. DC forward current.
8
50
40
30
20
HER
10
0
0
0.5
1.0
1.5
2.0
VF – FORWARD VOLTAGE - V
Figure 11. Forward current vs. forward voltage.
Figure 10. Maximum allowable average or DC current vs. ambient
temperature.
10
IF – FORWARD CURRENT PER SEGMENT – mA
IF AVE. MAX – MAXIMUM AVERAGE
FORWARD CURRENT PER SEGMENT – mA
HER Low Current
16
2.5
3.0
Intensity Bin Limits (mcd)
HER Low Current, AlGaAs Red Low Current
IV Bin Category
Color Categories
HDSP-31xL/H, HDSP-51xL/H
Min.
Max.
Dominant Wavelength (nm)
Color
Bin
Min.
Max.
Yellow
E
0.180
0.360
1
581.50
585.00
F
0.280
0.560
3
584.00
587.50
G
0.450
0.900
2
586.50
590.00
H
0.700
1.400
4
589.00
592.50
I
1.100
2.200
2
573.00
577.00
K
1.800
3.600
3
570.00
574.00
L
2.800
5.600
4
567.00
571.00
M
4.500
9.000
5
564.00
568.00
N
7.000
15.000
Green
Note:
All categories are established for classification of products. Products
may not be available in all categories. Please contact your local Avago
representatives for further clarification/information.
HER Std. Current, Green Std. Current, Yellow Std. Current
IV Bin Category
HDSP-31xE/G/Y, HDSP-51xE/G/Y
Min.
Max.
G
0.450
0.900
H
0.700
1.400
I
1.100
2.200
K
1.800
3.600
L
2.800
5.600
M
4.500
9.000
N
7.000
15.000
Electrical/Optical
Soldering/Cleaning
For more information on electrical/optical characteristics,
please see Application Note 1005.
Cleaning agents from the ketone family (acetone, methyl
ethyl ketone, etc.) and from the chlorinated hydrocarbon
family (methylene chloride, trichloro­ethylene, carbon
tetrachloride, etc.) are not recommended for cleaning LED
parts. All of these various solvents attack or dissolve the
encapsulating epoxies used to form the package of plastic
LED parts.
Contrast Enhancement
For information on contrast enhancement, please see
Application Note 1015.
For further information on soldering LEDs, please refer to
Application Note 1027.
For product information and a complete list of distributors, please go to our web site:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. Obsoletes 5989-2640EN
AV02-1769EN - March 28, 2011
Similar pages