Hirose HIF3BC-34PA-2.54DSA Ribbon cable connector compliant with mil standard Datasheet

Ribbon Cable connector Compliant with MIL Standard
HIF3B Series
■Features
1. Product Compliant with MIL Standard
HIF3B series has been developed as a product compliant with MIL
standard, and used for wide applications.
2. UL Approval Product
HIF3B series connectors are UL approved.
3. Mechanism to Prevent Mis-insertion
This connector is equipped with the mechanism to prevent Misinsertion as follows.
1 The system provides the convex area to insert the guide-key on the
pin header side, and to guide it in combination with the socket
convex area (MIL standard).
2 The system embeds and guides the polarizing key in the socket holes.
4. Applicable Cable AWG#28
The applicable cable is UL2651 AWG#28 flat cable (7 cores./
0.127mm, jacket dia. 0.9±0.1mm).
■Product Specifications
Current rating : 1A
Rating
Operating Temperature Range : –55 to +85ç (Note 1) Storage Temperature Range : –10 to +60ç (Note 2)
Storage Humidity Range : 40 to 70% (Note 2)
Voltage rating : 200V AC Operating Moisture Range : 40 to 80%
Item
Specification
Condition
1. Insulation Resistance
1000M ohms min.
500V DC
2. Withstanding voltage
No flashover or insulation breakdown.
650V AC/1 minute
3. Contact Resistance
15m ohms max.
0.1A
4. Vibration
No electrical discontinuity of 1µs or more
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.
5. Humidity (Steady state) Insulation resistance: 1000M ohms min.
6. Temperature Cycle
96 hours at temperature of 40ç and humidity of 90% to 95%
(-65ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.
No damage, cracks, or parts looseness.
125ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.) 5 cycles
7. Durability (Mating/un-mating) Contact resistance: 15m ohms max.
500 cycles
Flow: 260ç for 10 seconds
8. Resistance to Soldering heat No deformation of components affecting performance.
Manual soldering: 300ç for 3 seconds
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
■Material
Part
Material
Finish
Remarks
Insulator
PBT
Black
UL94V-0
D
Beryllium copper
Socket Contact
DA
Pin header contact
Copper alloy
Brass
Connection area
Gold plated
Connection area
Gold plated
Connection area
Gold plated
Connection area
Tin lead plated
Selective Gold plated
–––––––
–––––––
B15
■Ordering Information
●Socket
HIF 3B - * D A - 2.54 R
q
w
e
r
t
y
u
q Series Name
: HIF
w Series No.
: 3B, 3BA, 3BB (50, 60, 64 contacts only)
e Number of contacts : 16, 20, 26, 30, 34, 40, 50, 60, 64
r Contact alignment : D : Double
t
A
: VA type
y Contact pitch
: 2.54mm
u Connection type
R : ID type
●Pin Header
HIF 3B - * P A - 2.54 DS
q
w
e
q Series Name
: HIF
w Series No.
:
r
t
y
: (14 contacts not included)
3BC: (10 contacts only)
3BA, 3BB: (50, 60, 64 contacts only)
3BD: (10 contacts only)
3B
e Number of contacts : 16, 20, 26, 30, 34, 40, 50, 60, 64
r
P
t
A
y Contact pitch
: Pin header
: Selective gold plated
: 2.54mm
u Contact style
B16
u
DS
: Right angle type
DSA
: Straight type
■Socket (With guide to prevent mis-insertion)
Body
Protector
Clamp
Note1, Note2: The number of polarizing keys and polarizing keyways changes according to products. Refer to the list as shown below.
Note3: The 50, 60 and 64 contact connector contain two types of polarizing guides. Use the products, referring to Notes 1 and 2.
Note4: The 6 contact has no polarizing mark.
Unit:mm
Part Number
CL No.
HIF3BA- 6D-2.54R 610-0032-3
Part Number
CL No.
–––––––
Number of Contacts
A
B
C
D
6
12.19 5.08 6.35 7.72
Polarizing Guide
(Note 1)
Polarizing Keyway
(Note 2)
None
HIF3BA-10D-2.54R 610-0021-7 HIF3BA-10DA-2.54R 610-0651-5
10
17.27 10.16 11.43 12.8
★ HIF3BA-14D-2.54R 610-0022-0 HIF3BA-14DA-2.54R 610-0652-8
14
22.35 15.24 16.51 17.88
★ HIF3BA-16D-2.54R 610-0023-2 HIF3BA-16DA-2.54R 610-0653-0
16
24.89 17.78 19.05 20.42
★ HIF3BA-20D-2.54R 610-0024-5 HIF3BA-20DA-2.54R 610-0654-3
20
29.97 22.86 24.13 25.5
★ HIF3BA-26D-2.54R 610-0025-8 HIF3BA-26DA-2.54R 610-0655-6
26
37.59 30.48 31.75 33.12
★ HIF3BA-30D-2.54R 610-0026-0 HIF3BA-30DA-2.54R 610-0656-9
30
42.67 35.56 36.83 38.2
★ HIF3BA-34D-2.54R 610-0027-3 HIF3BA-34DA-2.54R 610-0657-1
34
47.75 40.64 41.91 43.28
★ HIF3BA-40D-2.54R 610-0028-6 HIF3BA-40DA-2.54R 610-0658-4
40
55.37 48.26 49.53 50.9
★ HIF3BA-50D-2.54R 610-0029-9 HIF3BA-50DA-2.54R 610-0659-7
50
One on right and
68.07 60.96 62.23 63.6 One on right and left sides, resp. left sides, resp.
★ HIF3BB-50D-2.54R 610-0041-4 HIF3BB-50DA-2.54R 610-0671-2
50
68.07 60.96 62.23 63.6
★ HIF3BA-60D-2.54R 610-0030-8 HIF3BA-60DA-2.54R 610-0660-6
60
80.77 73.66 74.93 76.3 One on right and left sides, resp.
★ HIF3BB-60D-2.54R 610-0042-7 HIF3BB-60DA-2.54R 610-0672-5
60
80.77 73.66 74.93 76.3
★ HIF3BA-64D-2.54R 610-0031-0 HIF3BA-64DA-2.54R 610-0661-9
64
85.85 78.74 80.01 81.38 One on right and left sides, resp.
★ HIF3BB-64D-2.54R 610-0043-0 HIF3BB-64DA-2.54R 610-0673-8
64
85.85 78.74 80.01 81.38
One on left side
One at center
One at center
One at center
One at center
The products marked with ★ comply with MIL standard.
B17
■Socket with Withdrawal Tab
Unit : mm
B18
Part Number
CL No.
Number of Contacts
A
B
HIF3BA-10D-2.54R-CL
610-0190-4
10
17.27
5.3
HIF3BA-16D-2.54R-CL
610-0192-0
16
24.89
12.9
HIF3BA-20D-2.54R-CL
610-0193-2
20
29.97
18.0
HIF3BA-26D-2.54R-CL
610-0194-5
26
37.59
25.5
HIF3BA-30D-2.54R-CL
610-0195-8
30
42.67
30.5
HIF3BA-34D-2.54R-CL
610-0196-0
34
47.75
35.8
HIF3BA-40D-2.54R-CL
610-0197-3
40
55.37
43.4
HIF3BA-50D-2.54R-CL
610-0198-6
HIF3BB-50D-2.54R-CL
610-0201-9
50
68.07
56.0
HIF3BA-60D-2.54R-CL
610-0199-9
HIF3BB-60D-2.54R-CL
610-0202-1
60
80.77
68.5
HIF3BA-64D-2.54R-CL
610-0200-6
HIF3BB-64D-2.54R-CL
610-0203-4
64
85.85
73.8
■Socket
Body
Protector
Clamp
Note1: The number of polarizing keys and polarizing keyways changes according to products. For details, refer to the list as shown below.
Note2: The 6 contact has no polarizing mark.
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
D
HIF3B- 6D-2.54R 610-0012-6
6
12.19 5.08 6.35 7.72
★ HIF3B-10D-2.54R 610-0001-0
10
17.27 10.16 11.43 12.80
★ HIF3B-14D-2.54R 610-0002-2
14
22.35 15.24 16.51 17.88
★ HIF3B-16D-2.54R 610-0003-5
16
24.89 17.78 19.05 20.42
★ HIF3B-20D-2.54R 610-0004-8
20
29.97 22.86 24.13 25.50
★ HIF3B-26D-2.54R 610-0005-0
26
37.59 30.48 31.75 33.12
★ HIF3B-30D-2.54R 610-0006-3
30
42.67 35.56 36.83 38.2
★ HIF3B-34D-2.54R 610-0007-6
34
47.75 40.64 41.91 43.28
★ HIF3B-40D-2.54R 610-0008-9
40
55.37 48.26 49.53 50.90
★ HIF3B-50D-2.54R 610-0009-1
50
68.07 60.96 62.23 63.6
★ HIF3B-60D-2.54R 610-0010-0
60
80.77 73.66 74.93 76.3
64
85.85 78.74 80.01 81.38
★ HIF3B-64D-2.54R 610-0011-3
Polarizing Guide
(Note 1)
None
One on left side
One on right and
left sides, resp.
The products marked with ★ comply with MIL standard.
B19
■Four Wall Angle Through hole
BPCB mounting pattern
Note 1, Note 2: The number of polarizing slot and key installed positions
changes according to products. Refer to the list as shown below.
Note 3: The spacer moves to the right according to the number of
contacts.
Note 4: The 10, 50, 60 and 64 contact connectors contain two types of
polarizing slots.
Use products, referring to (Note 1) (Note 2).
■n=number of contacts
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
★ HIF3BA-10PA-2.54DS 610-0091-2
10
32.0 17.5 10.16
HIF3BD-10PA-2.54DS 610-0171-0
10
32.0 17.5 10.16
★ HIF3BA-14PA-2.54DS 610-0092-5
14
37.1 22.6 15.24
★ HIF3BA-16PA-2.54DS 610-0093-8
16
39.6 25.1 17.78
★ HIF3BA-20PA-2.54DS 610-0094-0
20
44.7 30.2 22.86
★ HIF3BA-26PA-2.54DS 610-0095-3
26
52.3 37.8 30.48
★ HIF3BA-30PA-2.54DS 610-0096-6
30
57.4 42.9 35.56
★ HIF3BA-34PA-2.54DS 610-0097-9
34
62.5 48.0 40.64
★ HIF3BA-40PA-2.54DS 610-0098-1
40
70.1 55.6 48.26
★ HIF3BA-50PA-2.54DS 610-0099-4
50
82.8 68.3 60.96
★ HIF3BB-50PA-2.54DS 610-0131-5
50
82.8 68.3 60.96
★ HIF3BA-60PA-2.54DS 610-0100-1
60
95.5 81.0 73.66
★ HIF3BB-60PA-2.54DS 610-0132-8
60
95.5 81.0 73.66
★ HIF3BA-64PA-2.54DS 610-0101-4
64
100.6 86.1 78.74
★ HIF3BB-64PA-2.54DS 610-0133-0
64
100.6 86.1 78.74
D
28.14
MAX51.1
28.14
MAX51.1
33.24
MAX56.2
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
78.94
MAX101.9
91.64
MAX114.6
91.64
MAX114.6
96.74
MAX119.7
96.74
MAX119.7
E
F
21.8 27.9
Polarizing Slot
(Note 1)
Polarizing Key Install
(Note 2)
None
One on right side
21.8 27.9
None
26.9 33.0
One on right side
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
59.9 66.0
72.6 78.7 One on right and left sides, resp.
72.6 78.7
One on right and
left sides, resp.
One at center
85.3 91.4 One on right and left sides, resp.
85.3 91.4
One at center
90.4 96.5 One on right and left sides, resp.
90.4 96.5
One at center
The products marked with ★ comply with MIL standard.
B20
■Four-Wall Straight Through hole
BPCB mounting pattern
Note 1, Note 2: The number of polarizing slot and key installed positions
changes according to products. Refer to the list as shown below.
Note 3: The spacer moves to the right according to the number of
contacts.
Note 4: The 10, 50, 60 and 64 contact connectors contain two types of
polarizing slots.
Use products, confirming (Note 1) (Note 2).
Note 5: The 6 contact has no polarity mark.
■n=number of contacts
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
★ HIF3-6PA-2.54DSA
562-0503-9
6
26.92 12.42 05.08
HIF3BA-10PA-2.54DSA
★ HIF3BD-10PA-2.54DSA
610-0111-8
10
32.0 17.5 10.16
610-0181-3
10
32.0 17.5 10.16
★ HIF3BA-14PA-2.54DSA
610-0112-0
14
37.1 22.6 15.24
★ HIF3BA-16PA-2.54DSA
610-0113-3
16
39.6 25.1 17.78
★ HIF3BA-20PA-2.54DSA
610-0114-6
20
44.7 30.2 22.86
★ HIF3BA-26PA-2.54DSA
610-0115-9
26
52.3 37.8 30.48
★ HIF3BA-30PA-2.54DSA
610-0116-1
30
57.4 42.9 35.56
★ HIF3BA-34PA-2.54DSA
610-0117-4
34
62.5 48.0 40.64
★ HIF3BA-40PA-2.54DSA
610-0118-7
40
70.1 55.6 48.26
★ HIF3BA-50PA-2.54DSA
610-0119-0
50
82.8 68.3 60.96
★ HIF3BB-50PA-2.54DSA
610-0141-9
50
82.8 68.3 60.96
★ HIF3BA-60PA-2.54DSA
610-0120-9
60
95.5 81.0 73.66
★ HIF3BB-60PA-2.54DSA
610-0142-1
60
95.5 81.0 73.66
★ HIF3BA-64PA-2.54DSA
610-0121-1
64
100.6 86.1 78.74
64
100.6 86.1 78.74
★ HIF3BB-64PA-2.54DSA
610-0143-4
D
23.06
MAX46.02
28.14
MAX51.1
28.14
MAX51.1
33.24
MAX56.2
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
78.94
MAX101.9
91.64
MAX114.6
91.64
MAX114.6
96.74
MAX119.7
96.74
MAX119.7
Polarizing Slot
(Note 1)
Polarizing Key Install
(Note 2)
16.7 22.82
One at center
None
21.8 27.9
None
One on right side
E
F
21.8 27.9
None
26.9 33.0
One on right side
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
59.9 66.0
72.6 78.7 One on right and left sides, resp.
72.6 78.7
One on right and
left sides, resp.
One at center
85.3 91.4 One on right and left sides, resp.
85.3 91.4
One at center
90.4 96.5 One on right and left sides, resp.
90.4 96.5
One at center
The products marked with ★ comply with MIL standard.
B21
■Three Wall Angle Type
BPCB mounting pattern
Note 1, Note 2: The number of polarizing slot and key installed positions
changes according to products. Refer to the list as shown below.
Note 3: The spacer moves according to the number of contacts.
Note 4: The 10 contact connector consists of two types.
Use products, confirming (Note 1) (Note 2).
Note 5: The 6 contact has no polarity mark.
Note 6: The nut built-in specification product is also provided.
The product can be fixed by M2 screws from the rear side.
Use the screw of (board thickness) +4 mm under the neck.
■n=number of contacts
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
★ HIF3BD-10PA-2.54DS 610-0051-8
10
32.0 17.5 10.16
HIF3BC-10PA-2.54DS 610-0151-2
10
32.0 17.5 10.16
★ HIF3BD-16PA-2.54DS 610-0052-0
16
39.6 25.1 17.78
★ HIF3BD-20PA-2.54DS 610-0053-3
20
44.7 30.2 22.86
★ HIF3BD-26PA-2.54DS 610-0054-6
26
52.3 37.8 30.48
★ HIF3BD-30PA-2.54DS 610-0055-9
30
57.4 42.9 35.56
★ HIF3BD-34PA-2.54DS 610-0056-1
34
62.5 48.0 40.64
★ HIF3BD-40PA-2.54DS 610-0057-4
40
70.1 55.6 48.26
★ HIF3BD-50PA-2.54DS 610-0058-7
50
82.8 68.3 60.96
★ HIF3BD-60PA-2.54DS 610-0059-0
60
95.5 81.0 73.66
★ HIF3BD-64PA-2.54DS 610-0060-9
64
100.6 86.1 78.74
D
28.14
MAX51.1
28.14
MAX51.1
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
91.64
MAX114.6
96.74
MAX119.7
E
F
21.8 27.9
Polarizing Slot
(Note 1)
Polarizing Key Install
(Note 2)
None
One on right side
21.8 27.9
None
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
One on right and
left sides, resp.
59.9 66.0
72.6 78.7
85.3 91.4 One on right and left sides, resp.
90.4 96.5
The products marked with ★ comply with MIL standard.
B22
■Three Wall Straight Through hole
BPCB mounting pattern
Note1,Note2: The number of polarizing slot and key installed positions
changes according to products. Refer to the list as shown
below.
Note3: The spacer moves to the right according to the number of
contacts.
Note4: The 10 contact connector consists of two types.
Use products, referring to (Note 1) and (Note 2).
Note5: The 6 contact has no polarity mark.
■n=number of contacts
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
★ HIF3BD-10PA-2.54DSA 610-0071-5
10
32.0 17.5 10.16
HIF3BC-10PA-2.54DSA 610-0161-6
10
32.0 17.5 10.16
★ HIF3BD-16PA-2.54DSA 610-0072-8
16
39.6 25.1 17.78
★ HIF3BD-20PA-2.54DSA 610-0073-0
20
44.7 30.2 22.86
★ HIF3BD-26PA-2.54DSA 610-0074-3
26
52.3 37.8 30.48
★ HIF3BD-30PA-2.54DSA 610-0075-6
30
57.4 42.9 35.56
★ HIF3BD-34PA-2.54DSA 610-0076-9
34
62.5 48.0 40.64
★ HIF3BD-40PA-2.54DSA 610-0077-1
40
70.1 55.6 48.26
★ HIF3BD-50PA-2.54DSA 610-0078-4
50
82.8 68.3 60.96
★ HIF3BD-60PA-2.54DSA 610-0079-7
60
95.5 81.0 73.66
★ HIF3BD-64PA-2.54DSA 610-0080-6
64
100.6 86.1 78.74
D
28.14
MAX51.1
28.14
MAX51.1
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
91.64
MAX114.6
96.74
MAX119.7
E
F
21.8 27.9
Polarizing Slot
(Note 1)
Polarizing Key Install
(Note 2)
None
One on right side
21.8 27.9
None
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
One on right and
left sides, resp.
59.9 66.0
72.6 78.7
85.3 91.4 One on right and left sides, resp.
90.4 96.5
The products marked with ★ comply with MIL standard.
B23
■Four Wall Wrapping Type
BPCB mounting pattern
Note 1, Note 2. The number of polarizing slot and key installed positions
changes according to products. Refer to the list as shown below.
Note 3. The spacer moves to the right according to the number of
contacts.
Note 4. The 10, 50, 60 and 64 contact connectors consists of two types.
Use products, confirming (Note 1) (Note 2).
Note 5. The mark * indicates the number of contacts.
Note 6. The nut built-in specification product is also provided.
The product can be fixed by M2 screws from the rear side.
Use the screw of (board thickness) +4 mm under the neck.
■n=number of contacts
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
★ HIF3BA-10P-2.54W 610-0503-8
10
32.0 17.5 10.16
HIF3BD-10P-2.54W 610-0492-3
10
32.0 17.5 10.16
★ HIF3BA-14P-2.54W 610-0493-6
14
37.1 22.6 15.24
★ HIF3BA-16P-2.54W 610-0494-9
16
39.6 25.1 17.78
★ HIF3BA-20P-2.54W 610-0495-1
20
44.7 30.2 22.86
★ HIF3BA-26P-2.54W 610-0496-4
26
52.3 37.8 30.48
★ HIF3BA-30P-2.54W 610-0497-7
30
57.4 42.9 35.56
★ HIF3BA-34P-2.54W 610-0498-0
34
62.5 48.0 40.64
★ HIF3BA-40P-2.54W 610-0499-2
40
70.1 55.6 48.26
★ HIF3BA-50P-2.54W 610-0504-0
50
82.8 68.3 60.96
★ HIF3BB-50P-2.54W 610-0500-0
50
82.8 68.3 60.96
★ HIF3BA-60P-2.54W 610-0505-3
60
95.5 81.0 73.66
★ HIF3BB-60P-2.54W 610-0501-2
60
95.5 81.0 73.66
★ HIF3BA-64P-2.54W 610-0506-6
64
100.6 86.1 78.74
★ HIF3BB-64P-2.54W 610-0502-5
64
100.6 86.1 78.74
D
28.14
MAX51.1
28.14
MAX51.1
33.24
MAX56.2
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
78.94
MAX101.9
91.64
MAX114.6
91.64
MAX114.6
96.74
MAX119.7
96.74
MAX119.7
E
F
21.8 27.9
Polarizing Slot
(Note 1)
Polarizing Key Install
(Note 2)
None
One on right side
21.8 27.9
None
26.9 33.0
One on right side
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
59.9 66.0
72.6 78.7 One on right and left sides, resp.
72.6 78.7
One on right and
left sides, resp.
One at center
85.3 91.4 One on right and left sides, resp.
85.3 91.4
One at center
90.4 96.5 One on right and left sides, resp.
90.4 96.5
One at center
The products marked with ★ comply with MIL standard.
B24
■Four Wall Straight Through hole
[Flux Blister Prevention Type]
BPCB mounting pattern
Note1: The number of polarizing slot and key installed positions changes
according to products. Refer to the list as shown below.
■n=number of contacts
Unit:mm
Part Number
CL No.
Number of Contacts
A
B
C
★ HIF3CA-10PA-2.54DSA 610-0701-1
10
32.0 17.5 10.16
HIF3CD-10PA-2.54DSA 610-0722-1
10
32.0 17.5 10.16
★ HIF3CA-16PA-2.54DSA 610-0703-7
16
39.6 25.1 17.78
★ HIF3CA-20PA-2.54DSA 610-0704-0
20
44.7 30.2 22.86
★ HIF3CA-26PA-2.54DSA 610-0705-2
26
52.3 37.8 30.48
★ HIF3CA-30PA-2.54DSA 610-0706-5
30
57.4 42.9 35.56
★ HIF3CA-34PA-2.54DSA 610-0707-8
34
62.5 48.0 40.64
★ HIF3CA-40PA-2.54DSA 610-0708-0
40
70.1 55.6 48.26
★ HIF3CA-50PA-2.54DSA 610-0709-3
50
82.8 68.3 60.96
★ HIF3CB-50PA-2.54DSA 610-0721-9
50
82.8 68.3 60.96
★ HIF3CB-60PA-2.54DSA 610-0723-4
60
95.5 81.0 73.66
★ HIF3CB-64PA-2.54DSA 610-0724-7
64
100.6 86.1 78.74
D
28.14
MAX51.1
28.14
MAX51.1
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
78.94
MAX101.9
91.64
MAX114.6
96.74
MAX119.7
E
F
21.8 27.9
Polarizing Slot
Polarizing Key Install
None
One on right side
21.8 27.9
None
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
One on right and
left sides, resp.
59.9 66.0
72.6 78.7 One on right and left sides, resp.
72.6 78.7
85.3 91.4
One at center
90.4 96.5
The products marked with ★ comply with MIL standard.
B25
■Two Stage Staking Right Angle Through hole
Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer
to the list as shown below.
Note 3: The spacer moves to the right according to the number of contacts.
Note 4: The 10, 50, 60 and 64 contact connectors consists of two types.
Use products, confirming (Note 1) (Note 2).
Note 5: The mark * ndicates the number of contacts.
Note 6: The locator is located optionally.
Unit:mm
Part Number
CL No.
Number of Contacts
610-1502-0
10
32.0 17.5 10.16
HIF3BD-10PA-2.54WB 610-1503-3
★ HIF3BA-10PA-2.54WB
A
B
C
10
32.0 17.5 10.16
★ HIF3BA-16PA-2.54WB
610-1505-9
16
39.6 25.1 17.78
★ HIF3BA-20PA-2.54WB
610-1506-1
20
44.7 30.2 22.86
★ HIF3BA-26PA-2.54WB
610-1507-4
26
52.3 37.8 30.48
★ HIF3BA-30PA-2.54WB
610-1508-7
30
57.4 42.9 35.56
★ HIF3BA-34PA-2.54WB
610-1509-0
34
62.5 48.0 40.64
★ HIF3BA-40PA-2.54WB
610-1510-9
40
70.1 55.6 48.26
★ HIF3BA-50PA-2.54WB
610-1511-1
50
82.8 68.3 60.96
★ HIF3BB-50PA-2.54WB
610-1512-4
50
82.8 68.3 60.96
★ HIF3BA-60PA-2.54WB
610-1513-7
60
95.5 81.0 73.66
★ HIF3BB-60PA-2.54WB
610-1514-0
60
95.5 81.0 73.66
★ HIF3BA-64PA-2.54WB
610-1515-2
64
100.6 86.1 78.74
★ HIF3BB-64PA-2.54WB
610-1516-5
64
100.6 86.1 78.74
D
28.14
MAX51.1
28.14
MAX51.1
35.74
MAX58.7
40.84
MAX63.8
48.44
MAX71.4
53.54
MAX76.5
58.64
MAX81.6
66.24
MAX89.2
78.94
MAX101.9
78.94
MAX101.9
91.64
MAX114.6
91.64
MAX114.6
96.74
MAX119.7
96.74
MAX119.7
E
F
21.8 27.9
Polarizing Slot
(Note 1)
Polarizing Key Install
(Note 2)
None
One on right side
21.8 27.9
None
29.5 35.5
34.5 40.6
42.2 48.3
One at center
47.2 53.3
52.3 58.4
59.9 66.0
72.6 78.7 One on right and left sides, resp.
72.6 78.7
One on right and
left sides, resp.
One at center
85.3 91.4 One on right and left sides, resp.
85.3 91.4
One at center
90.4 96.5 One on right and left sides, resp.
90.4 96.5
One at center
The products marked with ★ comply with MIL standard.
B26
BCombination Pattern
Note : Fix the HIF3-mounting hole spacer by screws between upper stage and lower stage connectors.
BPCB mounting pattern
■Mounting Hole Spacer
Part Number
CL No.
HIF-3 mounting hole spacer
562-0714-4
Finish
PBT
Black
Note : 2 pieces are contained in a bag.
B27
BPolarizing Key
HIF3B-GK
CL562-0601-8
HIF3-GPIN(A)
HIF3BA-GPIN
Note1: One unit of this
product is a set of five
pieces in conjunction
with a runner. The unit
for sale is defined one
pack containing 20
pieces.
Note2: This product is
applicable to HIF3A*D2.54R, HIF3C*D2.54C and
HIF3BA-*D2.54C
products.
Part Number
CL No.
HIF3-GPIN(A) 562-0126-6
B28
Material
Remarks
Poly acetal (white)
A set of 5 pieces
Note1: One unit of this
product is a set of five
pieces in conjunction
with a runner. The unit
for sale is defined one
pack containing 20
pieces.
Note2: This product is
applicable to the
HIF3BA-*D2.54R
product.
Part Number
CL No.
HIF3BA-GPIN 612-0500-2
Material
Remarks
Poly acetal (white)
A set of 5 pieces
BHIF3-Multi Clamp
BHIF3-*CL Pull Tab
This clamp is used for intermediate connection in the
This pull tab is used for the HIF3 series equipped with cable clamp
bus-line system, etc. Remove compulsory force from the
function. Remove all compulsory force, which is loaded on the
insulation displacement area of the connector in
insulation displacement area of the connector for extraction.
intermediate connection.
Note: This HIF3-* Pull Tab can not be used for HIF3BA-*PD.
Note: The pin header corresponds to the HIF3BAE
Note: The pin header corresponds to the HIF3BAE series (lock E).
series (lock E).
BLock
Lock G
Lock F
Part Number : HIF3BAG-**PA-2.54DSA
Part Number : HIF3BAG-**PA-2.54DSA
●Low profile type, and used for lock ejection.
Connector height is reduced.
Since no connector clamp is needed on the cable side,
this is used without turning back on the cable side. Take
care about this point.
27.3
●F Type Lock Pin Header
21.5
●Low Profile Lock Pin Header
●Locking range more reduced than conventional lock type.
Even if connectors are aligned laterally, the mounting
space is reduced.
Note : The clamp must be replaced for HIF3A socket type
50 contacts only. Take care about this point.
B29
■Socket for Crimping
Unit: mm
B30
Part Number
CL No.
Number of Contacts
A
B
HIF3BA-10D-2.54C
610-1041-0
10
17.25
10.16
HIF3BA-14D-2.54C
610-1051-3
14
22.35
15.24
HIF3BA-16D-2.54C
610-1042-2
16
24.8
17.78
HIF3BA-20D-2.54C
610-1043-5
20
29.95
22.86
HIF3BA-26D-2.54C
610-1044-8
26
37.55
30.48
HIF3BA-30D-2.54C
610-1045-0
30
42.63
35.56
HIF3BA-34D-2.54C
610-1046-3
34
47.75
40.64
HIF3BA-40D-2.54C
610-1047-6
40
55.35
48.26
HIF3BA-50D-2.54C
610-1048-9
HIF3BB-50D-2.54C
610-1061-7
50
68.04
60.96
HIF3BA-60D-2.54C
610-1049-1
HIF3BB-60D-2.54C
610-1062-0
60
80.77
73.66
HIF3BA-64D-2.54C
610-1064-5
HIF3BB-64D-2.54C
610-1063-2
64
85.85
78.74
Polarizing Guide
One at center
One right and left side, resp.
One at center
One right and left side, resp.
One at center
One right and left side, resp.
One at center
■Cover Case for Crimping socket
Unit: mm
Part Number
CL No.
Number of Contacts
A
B
C
D
E
HIF3-20CV
562-0201-0
20
24.5
18.0
12.0
30.5
29.95
HIF3-26CV
562-0202-2
26
30.2
20.0
14.0
32.0
37.55
HIF3-30CV
562-0203-5
30
32.2
22.0
16.0
33.0
42.63
HIF3-34CV
562-0204-8
34
34.2
24.0
18.0
33.5
47.75
HIF3-40CV
562-0205-0
40
36.2
26.0
20.0
35.5
55.35
HIF3-50CV
562-0206-3
50
39.2
29.0
23.0
38.0
68.04
HIF3-60CV
562-0207-6
60
42.2
32.0
26.0
40.5
80.77
Note: The type F lock pin header cannot be used for a mating member.
B31
■Contact for Crimping Socket
HIF3-2226SC
HIF3-2226SCA
Applicable cable
Manual crimping tool
562-0079-8 gold plated contact in bag
562-0244-2 Selective gold plated contact in bag
AWG#22 to #26 UL 1007 Stranded wire
HIF3-T2226HC
HIF3-2226SCF 562-0080-7 gold plated contact in reel
* HIF3-2226SCFA 562-0245-5 Selective gold plated contact in reel
Applicable cable AWG#22 to #26 UL 1007 Stranded wire
Note:* products have both side careers.
562-0124-0 gold plated contact in bag
562-0246-8 Selective gold plated contact in bag
AWG#24 to #28 UL 1007 Stranded wire
HIF3-TA2428HC
HIF3-2022SC 562-0492-4 gold plated contact in bag
Applicable cable AWG#20 to #22 UL 1007 Stranded wire
Manual crimping tool HIF3-TA2022HC
HIF3-2428SCF 562-0125-3 gold plated contact in reel
* HIF3-2428SCFA 562-0247-0 Selective gold plated contact in reel
Applicable cable AWG#24 to #28 UL 1007 Stranded wire
HIF3-2022SCF 562-0493-7 gold plated contact in reel
Applicable cable AWG#20 to #22 UL 1007 Stranded wire
HIF3-2428SC
HIF3-2428SCA
Applicable cable
Manual crimping tool
Type VA (Selective gold plated in reel)
Applicable Cable
Part Number CL No.
HIF3-2226SCFC 613-0002-1 AWG#22 to #26 UL 1007 Stranded wire
HIF3-2630SCFC 613-0001-9 AWG#26 to #30 UL 1007 Stranded wire
HIF3A-3236SCFC 613-0005-0 AWG#32 to #36 UL 1007 Stranded wire
Type VA (Selective gold plated contact in bag)
Applicable Cable
Manual Crimp Tool A B C D E F
Part Number CL No.
HIF3-2226SCC 613-0004-7 AWG#22 to #26 UL 1007 Stranded wire HIF3-TB2226HC 11.5 0.8 1.8 1.8 2.3 2.6
HIF3-2630SCC 613-0003-4 AWG#26 to #30 UL 1007 Stranded wire HIF3-TB2630HC 11.5 0.8 1.4 1.35 2.0 2.1
B32
A
11.5
11.5
12.4
B
0.8
0.8
1.7
C
1.8
1.4
1.1
D
1.8
1.35
1.1
E
2.3
2.0
1.4
F
2.6
2.1
1.5
BTools
●Crimping Tool
Manual Crimping Tool
Part Number
CL No.
HIF3-T2226HC
550-0063-8
HIF3-T2226HC
●Automatic Crimping Tool (Type: CM-105)
●Contact Extraction Tools
Part Number
CL No.
HIF1-PO
550-0049-7
Part Number
CL No.
CM-105
901-0005-4
How to use the extraction tool
(1) How to extract contacts
(2) How to adjust the lance (raise)
As shown in Figure 1, where the
extraction tool is inserted in the lance
fixed slot on the insulated case, slightly
pull the cable, and the contact can be
removed.
In order to re-insert the contact
removed from the insulated case,
raise the contact lance area using the
tool A, and re-insert the contact, as
shown in Figure 2.
Figure 1
B33
Type
Item
Manual
Manual crimping tool
Automatic
Part Number
CL No.
550-0063-8
HIF3-TA2428HC
550-0100-2
HIF3-TA2022HC
550-0124-0
HIF3-2022SC
AWG#20 to #22
HIF3-TB2226HC
550-0154-1
HIF3-2226SCC
AWG#22 to #26
HIF3-TB2630HC
550-0155-4
HIF3-2630SCC
AWG#26 to #30
901-0005-4
–––––––
HIF3-2226SCF
HIF3-2428SCF
HIF3-2226SCFA
HIF3-2428SCFA
–––––––
AWG#22 to #26
AWG#24 to #28
AWG#22 to #26
AWG#24 to #28
AP105-HIF3-22-28SCF
901-4031-6
(Note1)
AP105-HIF3-22-28SCFA
901-4030-3
(Note1)
Extraction tool
HIF3-2226SC
HIF3-2226SCA
HIF3-2428SC
HIF3-2428SCA
AWG#22 to #26
AWG#24 to #28
AP105-HIF3-2022S
901-4027-9
HIF3-2022SCF
AWG#20 to #22
AP105-HIF3-2226SCFC
901-4005-6
HIF3-2226SCFC
AWG#22 to #26
AP105-HIF3-2630SCFC
901-4006-9
HIF3-2630SCFC
AWG#26 to #30
AP105-HIF3-3236SCFC
901-4007-1
HIF3-3236SCFC
AWG#32 to #36
HIF1-PO
550-0049-7
–––––––
–––––––
Note1: AP106-HIF3-22-28SCF and AP105-HIF3-22-28CFA can be modified by changing a few parts.
B34
Applicable Cable
HIF3-T2226HC
Automatic crimping tool unit CM-105
Applicator
Applicable Contact
BSocket Side (Crimping) Assembling Procedures
(1) As shown in Figure 1, peel the applicable cable (AWG#20 to #26) jacket, and connect it using crimping jig HIF3-TA2022HC,
HIF3-TA2226HC, or HIF3-TA2426HC. In this case, insert the cable so as to hit the contact cable stripper position as shown
Figure 2.
(2) After connection as shown Figure 2, check the contact direction, and insert the contact as shown Figures 3 and 4. Slightly pull
the cable, and check whether the contact lance position is firmly fixed to the insulation case, as shown in the area (A).
Note : For handling procedures for special crimping tools, refer to the "Handling Instruction Manual".
Figure 1
Figure 2
Figure 3
Figure 4
B35
HIF3B Connection Circuit Diagram
Type AB
Type AB
Type AD
Type AD
Type CD
Type CD
B36
Type AC
Type AC
Type CC
Type CC
Type AA
Type AA
B37
HIF2E R(S) A to HIF3B Connection Circuit Diagram
Type AA
Type AC
B38
Type BA
Type BC
B39
HIF2E R(S)B to HIF3 Connection Circuit Diagram
Type AA
Type AC
B40
Type BA
Type BC
B41
Similar pages