AVAGO HLMP-7019 Subminiature led lamp Datasheet

HLMP-Pxxx Series, HLMP-Qxxx Series
HLMP-6xxx Series, HLMP-70xx Series
Subminiature LED Lamps
Data Sheet
Description
Features
Flat Top Package
 Subminiature flat top package
The HLMP-Pxxx Series flat top lamps use an untinted, nondiffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications.
The flat top lamps are also ideal for use as emitters in light
pipe applications.
– ideal for backlighting and light piping applications
 Subminiature dome package
– diffused dome for wide viewing angle
– nondiffused dome for high brightness
Dome Packages
 TTL and LSTTL compatible 5 volt resistor lamps
The HLMP-6xxx Series dome lamps for use as indicators
use a tinted, diffused lens to provide a wide viewing angle
with a high on-off contrast ratio. High brightness lamps
use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern.
 Available in six colors
Resistor Lamps
The HLMP-6xxx Series 5 volt subminiature lamps with
built in current limiting resistors are for use in applications
where space is at a premium.
Lead Configurations
All of these devices are made by encapsulating LED chips
on axial lead frames to form molded epoxy subminiature
lamp packages. A variety of package configuration options is available. These include special surface mount
lead configurations, gull wing, yoke lead or Z-bend. Right
angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm
(0.200 inch) center spacing are available for through hole
mounting. For more information refer to Standard SMT
and Through Hole Lead Bend Options for Subminiature
LED Lamps data sheet.
 Ideal for space limited applications
 Axial leads
 Available with lead configurations for surface mount
and through hole PC board mounting
Device Selection Guide
Part Number: HLMP-xxxx
Standard
Red
DH AS
AlGaAs
Red
High
Efficiency
Red
Orange
P005
P105
P205
P102
6000
Yellow
High
Perf.
Green
Emerald
Green
P405
P305
P505
P605
P202
P402
P302
P502
Q100
6300
Q400
6400
6500
Q105
6305
Q405
6405
6505
Q150
7000
7019
7040
Q155
Untinted, Nondiffused,
Flat Top
A
Untinted, Diffused, Flat Top
A
Q600
Tinted, Diffused
B
Q605
Untinted, Nondiffused,
High Brightness
B
Tinted, Diffused, Low Current
B
Nondiffused, Low Current
B
6600
6700
6800
Tinted, Diffused, Resistor,
5 V, 10 mA
B
6620
6720
6820
Diffused, Resistor, 5 V, 4 mA
B
Ordering Information
HLMX-XXXX-X X X X X
Packaging
Option
Color Bin
Selection
Max. Iv Bin
Min. Iv Bin
4 x 4 Prod.
Part Number
2
Device Description[1]
Device
Outline
Drawing
Package Dimensions
(B) Diffused and Nondiffused
(A) Flat Top Lamps
0.50 (0.020) REF.
1.40 (0.055)
1.65 (0.065)
11.68 (0.460)
10.67 (0.420)
BOTH SIDES
11.68 (0.460)
10.67 (0.420)
BOTH SIDES
CATHODE
0.46 (0.018)
0.56 (0.022)
ANODE
1.65 (0.065)
DIA.
1.91 (0.075)
0.20 (0.008) MAX.
0.50 (0.020) REF.
0.46 (0.018)
0.56 (0.022)
ANODE
1.65 (0.065)
DIA.
1.91 (0.075)
0.25 (0.010) MAX.
NOTE 2
0.20 (0.008) MAX.
2.21 (0.087)
1.96 (0.077)
0.18 (0.007)
0.23 (0.009)
1.14 (0.045)
1.40 (0.055)
CATHODE
0.25 (0.010) MAX.
NOTE 2
2.21 (0.087)
1.96 (0.077)
0.76 (0.030) R.
0.89 (0.035)
0.94 (0.037)
1.24 (0.049)
2.03 (0.080)
1.78 (0.070)
0.63 (0.025)
0.38 (0.015)
2.44 (0.096)
1.88 (0.074)
2.92 (0.115)
MAX.
0.79 (0.031) MAX.
0.18 (0.007)
0.23 (0.009)
2.08 (0.082)
2.34 (0.092)
0.79 (0.031)
0.53 (0.021)
0.63 (0.025)
0.38 (0.015)
2.08 (0.082)
2.34 (0.092)
CATHODE
STRIPE
CATHODE
STRIPE
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD
POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.
CATHODE
TAB
NO. ANODE DOWN.
YES. CATHODE DOWN.
Figure 1. Proper right angle mounting to a PC board to prevent protruding cathode tab from shorting to anode connection.
3
Absolute Maximum Ratings at TA = 25°C
Parameter
Standard
Red
DH AS
AlGaAs
Red
High
Eff.
Red
Orange
Yellow
High Perf.
Green
Emerald
Green
Units
DC Forward Current[1]
50
30
30
30
20
30
30
mA
Peak Forward Current[2]
1000
300
90
90
60
90
90
mA
6
6
6
V
DC Forward Voltage
(Resistor Lamps Only)
6
Reverse Voltage (IR = 100 μA)
5
5
5
5
5
5
5
V
Transient Forward Current[3]
(10 μs Pulse)
2000
500
500
500
500
500
500
mA
-40 to +100
-20 to +100 °C
Operating Temperature Range:
Non-Resistor Lamps
-55 to +100
Resistor Lamps
Storage Temperature Range
-40 to +100
55 to +100
-40 to +85
-55 to +100
For Thru Hole Devices
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
260°C for 5 seconds
For Surface Mount Devices:
Reflow Soldering Temperature
260°C for 20 seconds
-20 to +85
°C
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at
this high current.
4
Electrical/Optical Characteristics, TA = 25°C
Standard Red
Device
HLMP-
Parameter
Symbol
6000-E00xx
6000-G00xx
Luminous Intensity[1]
IV
P005-F00xx
Min.
Typ.
0.63
1.2
1.60
3.2
1.0
2.5
Max.
Test Conditions
mcd
IF = 10 mA
V
IF = 10 mA
IR = 100 μA
Forward Voltage
VF
1.4
1.6
All
Reverse Breakdown
Voltage
VR
5.0
12.0
V
6000
Included Angle Between
21/2
90
Deg.
P005
Half Intensity Points[2]
All
5
2.0
Units
125
Peak Wavelength
PEAK
655
nm
Dominant Wavelength[3]
d
640
nm
Spectral Line Half Width
1/2
24
nm
Speed of Response
s
15
ns
Capacitance
C
100
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to-Cathode Lead
Luminous Efficacy[4]
v
65
lm/W
DH AS AlGaAs Red
Device
HLMP-
Min.
Typ.
P102-F00xx
1.0
20.0
P105-L00xx
10.0
30.0
P105-NP000
25
Q100-M00xx
16
45
25.0
45.0
Q100-N00xx
Parameter
Luminous Intensity
Symbol
IV
40
Q105-P00xx
40
Q105-ST000
160
Q150-F00xx
1.0
1.8
Q155-F00xx
1.0
4.0
Forward Voltage
VF
Q150/Q155
All
Reverse Breakdown Voltage
VR
Included Angle Between
Half Intensity Points[2]
21/
5.0
P105
Q100/Q150
6
Test Conditions
mcd
IF = 20 mA
125
200
500
IF = 1 mA
1.8
2.2
1.6
1.8
15.0
V
IF = 20 mA
IF = 1 mA
V
IR = 100 μA
125
2
90
Deg.
28
Q105/Q155
All
Units
80
Q100-PQ000
Q100
Max.
Peak Wavelength
PEAK
645
nm
Dominant Wavelength[3]
d
637
nm
Spectral Line Half Width
1/2
20
nm
Speed of Response
s
30
ns
Exponential Time
Constant; e-t/s
Capacitance
C
30
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to Cathode Lead
Luminous Efficacy[4]
v
80
lm/W
Measured at Peak
High Efficiency Red
Device
HLMP-
Min.
Typ.
P202-F00xx
1.0
5.0
P205-F00xx
1.0
8.0
P205-JK000
4.0
6300-F00xx
1.0
6300-KL000
Parameter
Luminous Intensity[1]
Symbol
IV
Max.
Units
Test Conditions
IF = 10 mA
12.5
10.0
6.3
20.0
mcd
6305-L00xx
10.0
40.0
7000-D00xx
0.4
1.0
IF = 2 mA
6600-G00xx
1.6
5.0
VF = 5.0 Volts
6620-F00xx
1.0
2.0
1.5
1.8
3.0
V
IF = 10 mA
9.6
13.0
mA
VF = 5.0 V
3.5
5.0
V
IR = 100 μA
All
Forward Voltage
(Nonresistor Lamps)
VF
6600
Forward Current
IF
6620
(Resistor Lamps)
All
Reverse Breakdown Voltage
VR
Included Angle Between
Half Intensity Points[2]
21/
5.0
P205
6305
125
2
7
28
Deg.
90
All Diffused
All
30.0
Peak Wavelength
PEAK
635
nm
Dominant Wavelength[3]
d
626
nm
Spectral Line Half Width
1/2
40
nm
Speed of Response
s
90
ns
Capacitance
C
11
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to-Cathode Lead
Luminous Efficacy[4]
v
145
lm/W
Measured at Peak
Orange
Device
HLMP-
Min.
Typ.
P402-F00xx
1.0
4.0
P405-F00xx
1.0
6
P405-JK000
Parameter
Luminous Intensity
Symbol
IV
4.0
Q400-F00xx
1.0
8
Q405-H00xx
2.5
14
Max.
Units
Test Conditions
12.5
mcd
IF = 10 mA
3.0
V
IF = 10 mA
IR = 100 μA
Forward Voltage
VF
1.5
1.9
Reverse Breakdown Voltage
VR
5.0
30.0
V
P40x
Included Angle Between
21/2
125
Deg.
Q40x
Half Intensity Points[2]
All
All
8
90
Peak Wavelength
PEAK
600
nm
Dominant Wavelength[3]
d
602
nm
Spectral Line Half Width
1/2
40
nm
Speed of Response
s
260
ns
Capacitance
C
4
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to-Cathode Lead
Luminous Efficacy[4]
v
380
lm/W
Measured at Peak
Yellow
Device
HLMP-
Min.
Typ.
P302-F00xx
1.0
3.0
P305-F00xx
1.0
4.0
6400-F00xx
1.0
9.0
6400-JK000
4.0
6405-J00xx
Parameter
Luminous Intensity[1]
Symbol
IV
3.6
Max.
Units
IF = 10 mA
12.5
20
Test Conditions
mcd
6405-MN0xx
16
50
7019-D00xx
0.4
0.6
IF = 2 mA
6700-G00xx
1.4
5.0
VF = 5.0 Volts
6720-F00xx
0.9
2.0
All
Forward Voltage
(Nonresistor Lamps)
VF
2.0
2.4
V
IF = 10 mA
6700
Forward Current
IF
9.6
13.0
mA
VF = 5.0 V
6720
(Resistor Lamps)
3.5
5.0
All
Reverse Breakdown
Voltage
P305
Included Angle Between
6405
Half Intensity Points[2]
5.0
VR
9
V
125
21/
2
All Diffused
All
50.0
28
Deg.
90
Peak Wavelength
PEAK
583
nm
Dominant Wavelength[3]
d
585
nm
Spectral Line Half Width
1/2
36
nm
Speed of Response
s
90
ns
Capacitance
C
15
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to-Cathode Lead
Luminous Efficacy[4]
v
500
lm/W
Measured at Peak
High Performance Green
Device
HLMP-
Min.
Typ.
P502-F00xx
1.0
3.0
P505-G00xx
1.6
6.3
6500-F00xx
1.0
7.0
10.0
40.0
7040-D00xx
0.4
0.6
IF = 2 mA
6800-G00xx
1.6
5.0
VF = 5.0 Volts
6820-F00xx
1.0
2.0
6505-L00xx
Parameter
Luminous Intensity[1]
Symbol
Iv
Max.
Units
Test Conditions
IF = 10 mA
mcd
All
Forward Voltage
(Nonresistor Lamps)
VF
2.1
2.7
V
IF = 10 mA
6800
Forward Current
IF
9.6
13.0
mA
VF = 5.0 V
6820
(Resistor Lamps)
3.5
5.0
All
Reverse Breakdown Voltage
V
IR = 100 μA
P505
Included Angle Between
6505
Half Intensity Points[2]
VR
50.0
125
21/2
All Diffused
All
5.0
28
Deg.
90
Peak Wavelength
PEAK
565
nm
Dominant Wavelength[3]
d
569
nm
Spectral Line Half Width
1/2
28
nm
Speed of Response
s
500
ns
Capacitance
C
18
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to-Cathode Lead
Luminous Efficacy[4]
v
595
lm/W
Notes:
1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous intensity for an array
determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching between arrays.
2. 1/2 is the off-axis angle where the luminous intensity is half the on-axis value.
3. Dominant wavelength, d, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines the color of the
device.
4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie = Iv/v, where Iv is the luminous intensity in
candelas and v is the luminous efficacy in lumens/watt.
10
Emerald Green[1]
Device
HLMP-
Parameter
Symbol
P605-F00xx
Q600-F00xx
Luminous Intensity
IV
Q605-F00xx
All
Forward Voltage
VF
Reverse Breakdown Voltage
VR
P605
Included Angle Between
21/2
Q60x
Half Intensity Points[2]
P605/Q600
Min.
Typ.
1.0
1.5
1.0
1.5
1.0
7.5
2.2
5.0
125
Max.
3.0
Units
Test Conditions
mcd
IF = 10 mA
V
IF = 10 mA
V
IR = 100 μA
Deg.
90
Peak Wavelength
PEAK
558
nm
Dominant Wavelength[3]
d
560
nm
Spectral Line Half Width
1/2
24
nm
Speed of Response
s
3100
ns
Capacitance
C
35
pF
VF = 0; f = 1 MHz
Thermal Resistance
RJ-PIN
170
°C/W
Junction-to-Cathode Lead
Luminous Efficacy[4]
V
656
lm/W
Measured at Peak
Note:
1. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation.
11
Figure 1. Relative intensity vs. wavelength.
Standard Red and DH AS
AlGaAs Red
High Efficiency Red, Orange, Yellow, High
Performance Green, and Emerald Green
100
FORWARD CURRENT – mA
90
HIGH EFFICIENCY
RED/ORANGE
80
70
60
YELLOW
50
40
30
HIGH
PERFORMANCE
GREEN,
EMERALD
GREEN
20
10
0
0
0.5
1
1.5
2
2.5
3
3.5
FORWARD VOLTAGE – V
Figure 2. Forward current vs. forward voltage (non-resistor lamp).
Standard Red, DH As AlGaAs Red
Figure 3. Relative luminous intensity vs. forward current (non-resistor lamp).
12
Low Current
HER, Orange, Yellow, and
High Performance Green,
and Emerald Green
Standard Red
DH As AlGaAs Red
HER, Orange, Yellow, and
High Performance Green,
and Emerald Green
Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current (non-resistor lamps).
Figure 5. Maximum forward dc current vs. ambient temperature. Derating based on TJ MAX = 110°C (non-resistor lamps).
Standard Red
HER, Orange, Yellow, and High Performance
Green
Figure 6. Maximum tolerable peak current vs. pulse duration (IDC MAX as per MAX ratings) (non-resistor lamps).
13
DH As AlGaAs Red
Figure 7. Resistor lamp forward current vs. forward voltage.
Figure 9. Relative intensity vs. angular displacement.
14
Figure 8. Resistor lamp luminous intensity vs. forward voltage.
Ordering Information
Color Bin Limits
HLMx-XXXX-X X X X X
Package
Bin
Min.
Emerald Green
0
Full Distribution
9
552
556
8
555
559
7
558
562
6
561
565
0
Full Distribution
6
561
565
5
564
568
4
567
571
3
570
574
2
573
577
0
Full Distribution
1
581.5
585.0
3
584.0
587.5
Packaging
Option
Color Bin
Selection
Green
Max. Iv Bin
Min. Iv Bin
4 x 4 Prod.
Part
Number
Yellow
Intensity Bin Limits
Max.
2
586.5
590.0
Bin
Min.
Max.
4
589.0
592.5
A
0.10
0.20
5
591.5
593.5
B
0.16
0.32
6
591.5
595.0
C
0.25
0.50
7
594.0
597.5
D
0.40
0.80
0
Full Distribution
E
0.63
1.25
1
596.5
600.0
F
1.00
2.00
2
599.0
602.5
Orange
G
1.60
3.20
3
601.5
604.0
H
2.50
5.00
4
603.8
608.2
J
4.00
8.00
5
606.8
611.2
K
6.30
12.50
6
609.8
614.2
L
10.00
20.00
7
612.8
617.2
M
16.00
32.00
8
615.8
620.2
N
25.00
50.00
P
40.00
80.00
Q
63.00
125.00
R
100.00
200.00
S
160.00
320.00
T
250.00
500.00
U
400.00
800.00
V
630.00
1250.00
W
1000.00
2000.00
X
1600.00
3200.00
Y
2500.00
5000.00
15
Mechanical Option
00
Straight Leads, Bulk Packaging, Quantity of 500 Parts
10
Right Angle Housing, Bulk Packaging, Quantity of 500 Parts
11
Gull Wing Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel
12
Gull Wing Lead, Bulk Packaging, Quantity of 500 Parts
14
Gull Wing Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel
21
Yoke Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel
22
Yoke Leads, Bulk Packaging, Quantity of 500 Parts
24
Yoke Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel
31
Z-Bend Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel
32
Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts
34
Z-Bend Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel
1L
2.54 mm (0.100 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)
1S
2.54 mm (0.100 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)
2L
5.08 mm (0.200 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)
2S
5.08 mm (0.200 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)
Note:
All Categories are established for classification of products. Products may not be available in all categories. Please contact your local Avago representative for further clarification/information.
For product information and a complete list of distributors, please go to our web site:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5989-1708EN
AV02-3609EN - June 12, 2012
Similar pages