HITTITE HMC382LP3E

HMC382LP3 / 382LP3E
v01.0610
AMPLIFIERS - LOW NOISE - SMT
7
GaAs PHEMT MMIC
LOW NOISE AMPLIFIER, 1.7 - 2.2 GHz
Typical Applications
Features
The HMC382LP3 / HMC382LP3E is ideal for:
Noise Figure: 1 dB
• Cellular/3G Infrastructure
Output IP3: +30 dBm
• Base Stations & Repeaters
Gain: 17 dB
• CDMA, W-CDMA, & TD-SCDMA
Externally Adjustable Supply Current
• GSM/GPRS & EDGE
Single Positive Supply: +5V
50 Ohm Matched Input/Output
Functional Diagram
General Description
The HMC382LP3 & HMC382LP3E high dynamic
range GaAs PHEMT MMIC Low Noise Amplifiers are
ideal for GSM & CDMA cellular basestation front-end
receivers operating between 1.7 and 2.2 GHz. This LNA
has been optimized to provide 1.0 dB noise figure, 17
dB gain and +30 dBm output IP3 from a single supply
of +5V. The HMC382LP3 & HMC382LP3E feature an
externally adjustable supply current which allows the
designer to tailor the linearity performance of the LNA
for each application. For applications which require
improved noise figure, please see the HMC618LP3(E).
Electrical Specifi cations, TA = +25° C, Vdd1, Vdd2 = +5V, Rbias = 16 Ohms*
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
Min.
1.7 - 1.9
14
Typ.
Max.
Min.
1.9 - 2.0
17
12
Typ.
Max.
Min.
2.0 - 2.1
15
11
Typ.
Max.
2.1 - 2.2
14
9
GHz
12
dB
Gain Variation Over Temperature
0.01
0.015
0.01
0.015
0.01
0.015
0.01
0.015
Noise Figure
1.0
1.3
1.05
1.35
1.15
1.45
1.2
1.5
Input Return Loss
13
12
11
10
dB
Output Return Loss
10
13
12
9
dB
Reverse Isolation
37
36
35
35
dB
Output Power for
1dB Compression (P1dB)
16
16
15.5
14
dBm
29.5
30
30
29.5
dBm
67
67
67
67
mA
Output Third Order Intercept (IP3)
(-20 dBm Input Power per tone,
1 MHz tone spacing)
Supply Current (Idd1 + Idd2)
* Rbias resistor value sets current. See application circuit herein.
7-1
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
dB/°C
dB
HMC382LP3 / 382LP3E
v01.0610
GaAs PHEMT MMIC
LOW NOISE AMPLIFIER, 1.7 - 2.2 GHz
Broadband Gain & Return Loss
7
Gain vs. Temperature
20
+25 C
+85 C
-40 C
20
10
S21
S11
S22
5
GAIN (dB)
RESPONSE (dB)
15
0
16
-5
12
-10
-15
-20
0.5
8
0.75
1
1.25
1.5 1.75
2 2.25
FREQUENCY (GHz)
2.5
2.75
1.6
3
Input Return Loss vs. Temperature
1.9
2
2.1
FREQUENCY (GHz)
2.2
2.3
0
-3
+25 C
+85 C
-40 C
-5
RETURN LOSS (dB)
RETURN LOSS (dB)
1.8
Output Return Loss vs. Temperature
0
-10
-15
+25 C
+85 C
-40 C
-6
-9
-12
-15
-20
1.6
1.7
AMPLIFIERS - LOW NOISE - SMT
24
25
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
2.2
1.6
2.3
Reverse Isolation vs. Temperature
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
2.2
2.3
2.2
2.3
Noise Figure vs. Temperature
-15
2
-20
NOISE FIGURE (dB)
ISOLATION (dB)
1.6
-25
+25 C
+85 C
-40 C
-30
-35
-40
0.8
+25 C
+85 C
-40 C
0.4
-45
-50
1.6
1.2
0
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
2.2
2.3
1.6
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7-2
HMC382LP3 / 382LP3E
v01.0610
GaAs PHEMT MMIC
LOW NOISE AMPLIFIER, 1.7 - 2.2 GHz
Psat vs. Temperature @ Idd = 67 mA
20
20
18
18
Psat (dBm)
P1dB (dBm)
P1dB vs. Temperature @ Idd = 67 mA
16
14
+25 C
+85 C
-40 C
12
10
1.8
1.9
2
FREQUENCY (GHz)
2.1
2.2
Output IP3 vs. Temperature Idd = @ 67 mA
1.9
2
FREQUENCY (GHz)
2.1
1.4
Noise Figure
GAIN (dB) & P1dB (dBm)
22
30
28
26
+25 C
+85 C
-40 C
20
1.8
1.9
2
FREQUENCY (GHz)
2.1
2.2
Absolute Maximum Ratings
1.2
20
1
18
0.8
16
0.6
12
60
0.4
GAIN
P1dB
14
22
0.2
70
80
90
100
110
Typical Supply Current vs. Vdd1 & Vdd2
+8.0 Vdc
Vdd (Vdc)
Idd (mA)
RF Input Power (RFIN)(Vs = +5.0 Vdc)
+10 dBm
+4.5
67.2
Channel Temperature
150 °C
0.451 W
Thermal Resistance
(channel to ground paddle)
144 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
120
SUPPLY CURRENT (mA)
Drain Bias Voltage (Vdd1, Vdd2)
Continuous Pdiss (T = 85 °C)
(derate 6.94 mW/°C above 85 °C)
2.2
Gain, Noise Figure & P1dB vs.
Supply Current @ 1900 MHz
32
IP3 (dBm)
1.8
24
24
7-3
1.7
34
1.7
+25 C
+85 C
-40 C
14
12
10
1.7
16
NOISE FIGURE (dB)
AMPLIFIERS - LOW NOISE - SMT
7
+5.0
67.4
+5.5
67.6
Recommended Bias Resistor Values
for Various Idd1 & Idd2
Idd1 + Idd2 (mA)
Rbias (Ohms)
60
27
70
16
80
13
100
8.2
120
3.9
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC382LP3 / 382LP3E
v01.0610
GaAs PHEMT MMIC
LOW NOISE AMPLIFIER, 1.7 - 2.2 GHz
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
AMPLIFIERS - LOW NOISE - SMT
7
Outline Drawing
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC382LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC382LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
382
XXXX
[2]
382
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7-4
HMC382LP3 / 382LP3E
v01.0610
GaAs PHEMT MMIC
LOW NOISE AMPLIFIER, 1.7 - 2.2 GHz
AMPLIFIERS - LOW NOISE - SMT
7
Pin Descriptions
Pin Number
Function
Description
1, 4, 5, 7, 9,
12, 14, 16
N/C
No connection necessary. These pins may be connected to
RF/DC ground. Performance will not be affected.
2
RFIN
This pin is AC coupled and matched to 50 Ohms.
3, 6, 10
GND
These pins and package bottom must
be connected to RF/DC ground.
8
Res
This pin is used to set the DC current of the amplifier
by selection of external bias resistor.
See application circuit.
11
RFOUT
This pin is AC coupled and matched to 50 Ohms.
13,15
Vdd2, Vdd1
Power supply voltage. Choke inductor and bypass
capacitors are required. See application circuit.
Interface Schematic
Application Circuit
Note: L1, L2 and C1 should be located as close to pins as possible.
7-5
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC382LP3 / 382LP3E
v01.0610
GaAs PHEMT MMIC
LOW NOISE AMPLIFIER, 1.7 - 2.2 GHz
7
AMPLIFIERS - LOW NOISE - SMT
Evaluation PCB
List of Materials for Evaluation PCB 112582 [1]
Item
Description
J1 - J2
PCB Mount SMA RF Connector
J3 - J5
DC Pin
C1
10 pF Capacitor, 0402 Pkg.
C2, C3
1000 pF Capacitor, 0603 Pkg.
C4, C5
15000 pF Capacitor, 0603 Pkg.
L1
56nH Inductor, 0603 Pkg.
L2
18nH Inductor, 0603 Pkg.
R1
Resistor, 0402 Pkg.
U1
HMC382LP3 / HMC382LP3E Amplifier
PCB [2]
112580 Evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed ground paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7-6