Hittite HMC540LP3 1 db lsb gaas mmic 4-bit digital positive control attenuator, dc - 5.5 ghz Datasheet

HMC540LP3 / 540LP3E
v00.0605
1 dB LSB GaAs MMIC 4-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5.5 GHz
ATTENUATORS - SMT
5
Typical Applications
Features
The HMC540LP3 / HMC540LP3E is ideal for both RF
1 dB LSB Steps to 15 dB
and IF applications:
± 0.2 dB Typical Step Error
• Cellular Infrastructure
Low Insertion Loss: 1 dB
• ISM, MMDS, WLAN, WiMAX, WiBro
High IP3: +50 dBm
• Microwave Radio & VSAT
Single Control Line Per Bit
TTL/CMOS Compatible Control
• Test Equipment and Sensors
Single +5V Supply
Functional Diagram
3x3 mm SMT Package
General Discription
The HMC540LP3 & HMC540LP3E are broadband
4-bit GaAs IC digital attenuators in low cost leadless
surface mount packages. This single positive control
line per bit digital attenuator utilizes off chip AC
ground capacitors for near DC operation, making it
suitable for a wide variety of RF and IF applications.
Covering DC to 5.5 GHz, the insertion loss is less
than 1 dB typical. The attenuator bit values are
1 (LSB), 2, 4 and 8 dB for a total attenuation of 15 dB.
Attenuation accuracy is excellent at ± 0.2 dB typical
step error. The attenuator also features a IIP3 of +50
dBm. Four TTL/CMOS control inputs are used to
select each attenuation state. A single Vdd bias of
+5V is required.
Electrical Specifi cations,
TA = +25° C, With Vdd = +5V & Vctl = 0/+5V (Unless Otherwise Noted)
Parameter
Typ.
Max.
Units
Insertion Loss
DC - 2.0 GHz
2.0 - 3.0 GHz
3.0 - 4.0 GHz
4.0 -5.5 GHz
0.8
1.0
1.3
2.2
1.1
1.3
1.6
2.6
dB
dB
dB
dB
Attenuation Range
DC - 5.5 GHz
15
dB
Return Loss (RF1 & RF2, All Atten. States)
DC - 3.5 GHz
3.5 - 5.5 GHz
20
15
dB
dB
Attenuation Accuracy:
(Referenced to Insertion Loss)
Frequency (GHz)
All States
Input Power for 0.1 dB Compression
Input Third Order Intercept Point
(Two-Tone Input Power= 0 dBm Each Tone)
REF - 4 dB States
5 - 15 dB States
DC - 1.0 GHz
1.0 - 4.0 GHz
4.0 - 5.0 GHz
5.0 - 5.5 GHz
Min.
± (0.2 + 2% of Atten. Setting) Max.
± (0.2 + 3% of Atten. Setting) Max.
± (0.3 + 5% of Atten. Setting) Max.
± (0.4 + 8% of Atten. Setting) Max.
dB
dB
dB
dB
0.1 - 5.5 GHz
27
dBm
0.1 - 5.5 GHz
50
45
dBm
dBm
95
100
ns
ns
Switching Characteristics
DC -5.5 GHz
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
5 - 170
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC540LP3 / 540LP3E
v00.0605
1 dB LSB GaAs MMIC 4-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5.5 GHz
5
Return Loss RF1, RF2
(Only Major States are Shown)
Insertion Loss
RETURN LOSS (dB)
INSERTION LOSS (dB)
-0.5
-1
-1.5
+25 C
+85 C
-40 C
-2
-10
I.L.dB 1 dB 2 dB
4 dB 8 dB 15 dB
-20
-30
-2.5
-3
-40
0
1
2
3
4
5
0
6
1
2
FREQUENCY (GHz)
3
4
5
6
FREQUENCY (GHz)
Normalized Attenuation
(Only Major States are Shown)
Bit Error vs. Attenuation State
2
1.5
-4
BIT ERROR (dB)
NORMALIZED ATTENUATION (dB)
0
ATTENUATORS - SMT
0
0
-8
-12
-16
5.5 GHz
5 GHz
1
0.5
4 GHz
0
-0.5
1 GHz
-20
100 MHz
-1
0
1
2
3
4
5
6
0
4
FREQUENCY (GHz)
8
12
16
ATTENUATION STATE (dB)
Bit Error vs. Frequency
Relative Phase vs. Frequency
(Only Major States are Shown)
(Only Major States are Shown)
1.5
40
30
0.5
RELATIVE PHASE (deg)
BIT ERROR (dB)
1
1-4 dB
0
-0.5
15 dB
20
8 dB
10
0
-10
1-4 dB
-20
-30
15 dB
8 dB
-40
-1
0
1
2
3
4
FREQUENCY (GHz)
5
6
0
1
2
3
4
5
6
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 171
HMC540LP3 / 540LP3E
v00.0605
1 dB LSB GaAs MMIC 4-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5.5 GHz
5
Worst Case Step Error
Between Successive Attenuation States
0.3
0.2
STEP ERROR (dB)
ATTENUATORS - SMT
0.4
0.1
0
-0.1
-0.2
-0.3
-0.4
-0.5
0
1
2
3
4
5
6
FREQUENCY (GHz)
Bias Voltage & Current
Truth Table
Vdd = +5.0 Vdc ± 10%
Vdd
(VDC)
Control Voltage Input
Idd (Typ.)
(mA)
+4.5
3.0
+5.0
3.2
+5.5
3.4
Control Voltage
State
Bias Condition
Low
0 to +0.8V @ -5 uA Typ.
High
+2.0 to + 5.0 Vdc @ 40 uA Typ.
V2
4 dB
V3
2 dB
V4
1 dB
High
High
High
High
High
High
High
Low
1 dB
High
High
Low
High
2 dB
Reference
I.L.
High
Low
High
High
4 dB
Low
High
High
High
8 dB
Low
Low
Low
Low
15 dB
Any combination of the above states will provide an attenuation
approximately equal to the sum of the bits selected.
Note: Vdd = +5V
5 - 172
Attenuation
State
RF1 - RF2
V1
8 dB
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC540LP3 / 540LP3E
v00.0605
1 dB LSB GaAs MMIC 4-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5.5 GHz
RF Input Power (DC - 5.5 GHz)
+29 dBm (T = +85 °C)
Control Voltage Range (V1 to V4)
-1V to Vdd +1V
Bias Voltage (Vdd)
+7.0 Vdc
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 11.7 mW/°C above 85 °C)
0.769 W
Thermal Resistance
85 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
ATTENUATORS - SMT
5
Absolute Maximum Ratings
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC540LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC540LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
540
XXXX
[2]
540
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 173
HMC540LP3 / 540LP3E
v00.0605
1 dB LSB GaAs MMIC 4-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5.5 GHz
ATTENUATORS - SMT
5
Pin Descriptions
Pin Number
Function
Description
1
Vdd
Supply Voltage.
2, 11
RF1, RF2
This pin is DC coupled and matched to 50 Ohm.
Blocking capacitors are required.
Select value based on lowest frequency of operation.
3, 7, 9, 10, 12
N/C
These pins should be connected to PCB RF ground to
maximize performance.
4 - 6, 8
ACG1 - ACG4
External capacitor to ground is required. Select value for
lowest frequency of operation. Place capacitor as close
to pins as possible.
13 - 16
V1 - V4
See truth table and control voltage table.
GND
Package bottom has an exposed metal paddle that must be
connected to RF/DC Ground.
Interface Schematic
Application Circuit
Recommended Component Values
5 - 174
C1 - C3
1,000 pF ± 10%
C4, C5
330 pF ± 10%
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC540LP3 / 540LP3E
v00.0605
1 dB LSB GaAs MMIC 4-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5.5 GHz
5
ATTENUATORS - SMT
Evaluation PCB
List of Materials for Evaluation PCB 111315 [1]
Item
Description
J1 - J2
PCB Mount SMA Connector
J3 - J8
DC Pin
C1 - C3
1000 pF Capacitor, 0402 Pkg.
C4, C5
330 pF Capacitor, 0402 Pkg.
U1
HMC540LP3 / HMC540LP3E
Digital Attenuator
PCB [2]
111291 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 175
Similar pages