Hittite HMC576 Gaas mmic x2 active frequency multiplier, 18 - 29 ghz output Datasheet

HMC576
v00.0506
FREQUENCY MULTIPLIERS - ACTIVE - CHIP
2
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 18 - 29 GHz OUTPUT
Typical Applications
Features
The HMC576 is suitable for:
High Output Power: +17 dBm
• Clock Generation Applications:
SONET OC-192 & SDH STM-64
Low Input Power Drive: -2 to +6 dBm
• Point-to-Point & VSAT Radios
Fo Isolation: >20 dBc @ Fout= 24 GHz
100 KHz SSB Phase Noise: -132 dBc/Hz
• Test Instrumentation
Single Supply: +5V@ 82 mA
• Military EW / Radar
Die Size: 1.18 x 1.23 x 0.1 mm
• Space
Functional Diagram
General Description
The HMC576 die is a x2 active broadband frequency
multiplier utilizing GaAs PHEMT technology. When
driven by a +3 dBm signal, the multiplier provides
+17 dBm typical output power from 18 to 29
GHz. The Fo and 3Fo isolations are >20 dBc and
>30 dBc respectively at 24 GHz. The HMC576 is ideal
for use in LO multiplier chains for Pt to Pt & VSAT
Radios yielding reduced parts count vs. traditional
approaches. The low additive SSB Phase Noise of
-132 dBc/Hz at 100 kHz offset helps maintain good
system noise performance.
Electrical Specifi cations, TA = +25° C, Vdd1, Vdd2 = 5.0V, 3 dBm Drive Level
Parameter
Min.
Frequency Range, Input
Frequency Range, Output
Output Power
11
Max.
Units
GHz
18 - 29
GHz
17
dBm
Fo Isolation (with respect to output level)
20
dBc
3Fo Isolation (with respect to output level)
17
dBc
Input Return Loss
10
dB
Output Return Loss
SSB Phase Noise (100 kHz Offset)
Supply Current (Idd1 & Idd2)
2 - 44
Typ.
9.0 - 14.5
9
dB
-132
dBc/Hz
82
mA
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC576
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 18 - 29 GHz OUTPUT
Output Power vs. Drive Level
20
25
18
20
16
15
14
12
10
+25C
+85C
-55C
8
6
4
2
10
5
0
-5
-10
-15
-6dBm
-4dBm
-2dBm
0dBm
-20
2
-25
0
2dBm
4dBm
6dBm
-30
17
18 19 20
21 22 23
24
25 26 27
28 29
17
30
18 19 20
OUTPUT FREQUENCY (GHz)
21 22 23
24
25 26 27
28 29
30
28 29
30
OUTPUT FREQUENCY (GHz)
Output Power vs.
Supply Voltage @ 3 dBm Drive Level
Isolation @ 3 dBm Drive Level
20
20
OUTPUT POWER (dBm)
16
14
12
10
4.5V
5.0V
5.5V
8
6
4
10
0
-10
Fo
2Fo
3Fo
-20
2
0
-30
17
18 19 20
21 22 23
24
25 26 27
28 29
17
30
18 19 20
OUTPUT FREQUENCY (GHz)
21 22 23
24
25 26 27
OUTPUT FREQUENCY (GHz)
Output Power vs. Input Power
20
15
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
18
FREQUENCY MULTIPLIERS - ACTIVE - CHIP
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Output Power vs.
Temperature @ 3 dBm Drive Level
10
5
0
-5
18GHz
24GHz
29GHz
-10
-15
-20
-10
-8
-6
-4
-2
0
2
4
6
8
10
INPUT POWER (dBm)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 45
HMC576
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 18 - 29 GHz OUTPUT
Output Return Loss vs. Temperature
Input Return Loss vs. Temperature
2 - 46
0
0
+25C
+85C
-55C
-5
OUTPUT RETURN LOSS (dB)
INPUT RETURN LOSS (dB)
FREQUENCY MULTIPLIERS - ACTIVE - CHIP
2
-10
-15
-20
-25
-2
-4
-6
-8
-10
-12
-14
-16
+25C
+85C
-55C
-18
-30
-20
8
9
10
11
12
FREQUENCY (GHz)
13
14
15
17
18
19
20
21
22
23
24
25
26
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
27
28
29
HMC576
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 18 - 29 GHz OUTPUT
Typical Supply Current vs. Vdd
RF Input (Vdd = +5V)
+20 dBm
Vdd (V)
Idd (mA)
Supply Voltage (Vdd1, Vdd2)
+6.0 Vdc
4.5
82
Channel Temperature
175 °C
Continuous Pdiss (T= 85 °C)
(derate 7.9 mW/°C above 85 °C)
709 mW
Thermal Resistance
(channel to die bottom)
126 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
5.0
82
5.5
83
Note:
Multiplier will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
Standard
Alternate [2]
GP-2 (Gel Pack)
—
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] Reference this suffix only when ordering alternate die
packaging.
2
FREQUENCY MULTIPLIERS - ACTIVE - CHIP
Absolute Maximum Ratings
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MILLIMETERS].
2. DIE THICKNESS IS .004”
3. TYPICAL BOND PAD IS .004” SQUARE.
4. TYPICAL BOND SPACING IS .006” CENTER TO CENTER.
5. BOND PAD METALIZATION: GOLD
6. BACKSIDE METALIZATION: GOLD
7. BACKSIDE METAL IS GROUND.
8. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 47
HMC576
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 18 - 29 GHz OUTPUT
Pad Description
FREQUENCY MULTIPLIERS - ACTIVE - CHIP
2
2 - 48
Pad Number
Function
Description
1, 2
Vdd1, Vdd2
Supply voltage 5V ± 0.5V.
3
RFOUT
Pin is AC coupled and matched to
50 Ohms from 18 - 29 GHz.
4, 5
GND
Die bottom must be connected to RF ground.
6
RFIN
Pin is AC coupled and matched to
50 Ohms from 9 - 14.5 GHz.
Interface Schematic
Assembly Diagram
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC576
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 18 - 29 GHz OUTPUT
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should
be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the
surface of the substrate. One way to accomplish this is to attach the 0.102mm
(4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab)
which is then attached to the ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire 3 mil Ribbon Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order
to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3
mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12
mils) is recommended to minimize inductance on RF, LO & IF ports.
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer
capacitor (mounted eutectically or by conductive epoxy) placed no further than
0.762mm (30 Mils) from the chip is recommended.
Handling Precautions
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Static Sensitivity: Follow ESD precautions to protect against > ± 250V ESD
strikes.
2
Ribbon Bond
0.076mm
(0.003”)
RF Ground Plane
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip may have fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The
mounting surface should be clean and flat.
FREQUENCY MULTIPLIERS - ACTIVE - CHIP
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature
of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the
chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required
for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 49
Similar pages