Hittite HMC597LP4E Sige wideband direct demodulator rfic, 100 - 4000 mhz Datasheet

HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Typical Applications
Features
The HMC597LP4 / HMC597LP4E is suitable for
various modulation systems:
High Linearity: +25 dBm IIP3 & +60 dBm IIP2
• Cellular/PCS/3G
High Integration: On-Chip RF Balun
Low Noise Figure: 15 dB
• Base Stations & Repeaters
• GSM/GPRS, WCDMA & TD-SCDMA
• WiMAX, WiBro & Fixed Wireless
Functional Diagram
DEMODULATORS - SMT
9
General Description
The HMC597LP4(E) are highly integrated SiGe
wideband direct conversion I/Q Demodulator RFICs
which are ideal for high dynamic range receivers
operating from 100 - 4000 MHz in cellular and
broadband wireless infrastructure applications.
Providing a very high level of integration compared
with discrete solutions, the HMC597LP4(E) features an
on-chip RF balun which allows for singled ended RF
input. An off-chip capacitor allows the reconfiguration
of the RF port to operate over the whole 100 - 4000
MHz band without additional off-chip components.
Also ideal for software radio and other multi-band
receivers, the HMC597LP4(E) demodulator is housed
in a compact 4 x 4 mm SMT QFN package and delivers
exceptionally high dynamic range. The LO requires -6
to +6 dBm and can be driven in single-ended mode.
The I and Q output ports are differential with an output
impedance of 400 Ohms, allowing direct connection to
channel filters and ADCs. This device is optimized for
a supply voltage of +4.5V to +5.5V and consumes 200
mA @ +5V supply.
Electrical Specifi cations, See Test Conditions on following page herein.
Parameter
RF Input Frequency (Direct LO)
Typ.
Max.
Units
0.1 - 4.0
GHz
Input P1dB
12
dBm
SSB Noise Figure
15
dB
+25
dBm
Input IP2
+60
dBm
Conversion Gain
-3.5
dB
LO to RF Leakage @ +3 dBm LO
-66
dBm
IF Port Bandwidth
600
MHz
IF Output Impedance (Diff.)
400
Ohms
Input IP3
LO Input Power
9 - 42
Min.
-6 to +6
dBm
LO/RF Return Loss
12/12
dB
Total Supply Current
200
230
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
mA
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
DC Test Conditions [1]
AC Test Conditions [1]
Parameter
Condition
Parameter
Condition
Temperature
25 °C
RF Input Frequency
1970 MHz
Supply
200mA @ +5V
RF Input Frequency for IIP3
1970 & 1971 MHz
[1} Unless otherwise specified, the following test conditions were
used. Please refer to the HMC597LP4(E) application schematic.
RF Input Power for IIP3
0 dBm per Tone
LO Frequency
1960 MHz
LO Input Power
0 dBm single ended through LOP
P1dB, Noise Figure, Gain vs. Frequency [1]
Input IP3 vs. Frequency [1]
40
25
35
C26= 0pF
C26= 6.8pF
C26= 0.9pF
20
30
NF
INPUT IP3 (dBm)
NF (dB), P1dB (dBm) & GAIN (dB)
30
15
10
P1dB
5
25
20
15
0
10
-5
5
GAIN
-10
C26= 0pF
C26= 6.8pF
C26= 0.9pF
0
0
0.5
1
1.5
2
2.5
3
3.5
4
0
0.5
1
RF FREQUENCY (GHz)
RF Return Loss vs. Frequency
2
2.5
3
3.5
4
3.5
4
LO & Return Loss vs. Frequency
0
0
C26=0pF
RETURN LOSS (dB)
RF RETURN LOSS (dB)
1.5
RF FREQUENCY (GHz)
DEMODULATORS - SMT
9
-5
C26=6.8pF
-10
-5
-10
-15
C26=0.9pF
-15
-20
0
0.5
1
1.5
2
2.5
RF FREQUENCY (GHz)
3
3.5
4
0
0.5
1
1.5
2
2.5
3
RF FREQUENCY (GHz)
[1] IF Frequency= 10 MHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 43
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Noise Figure, P1dB,
Gain @ 900 MHz vs. LO Power [1]
LO - RF Isolation vs. Frequency
25
9
NF (dB), P1dB (dBm) & GAIN (dB)
LO-RF ISOLATION (dB)
0
-20
-40
-60
-80
NF
20
15
10
P1dB
5
0
-5
GAIN
-10
-100
0
0.5
1
1.5
2
2.5
3
3.5
-9
4
-6
Noise Figure, P1dB,
Gain @ 1970 MHz vs. LO Power [1]
0
3
9
20
NF (dB), P1dB (dBm) & GAIN (dB)
25
NF
15
10
P1dB
5
0
-5
GAIN
-10
NF
20
15
10
P1dB
5
0
-5
GAIN
-10
-9
-6
-3
0
LO POWER (dBm)
3
6
9
-9
-6
-3
0
3
LO POWER (dBm)
[1] IF Frequency= 10 MHz
9 - 44
6
Noise Figure, P1dB,
Gain @ 3500 MHz vs. LO Power [1]
25
NF (dB), P1dB (dBm) & GAIN (dB)
DEMODULATORS - SMT
-3
LO POWER (dBm)
RF FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6
9
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Absolute Maximum Ratings
+6V
LO Input Power
+12 dBm
Channel Temperature
150 °C
Continuous Pdiss (T = 85°C)
(Derate 30 mW/°C above 85°C)
2 Watts
Thermal Resistance (Rth)
(junction to lead)
36
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
9
DEMODULATORS - SMT
Vcc1, Vcc2
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC597LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC597LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H597
XXXX
[2]
H597
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 45
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Pin Descriptions
DEMODULATORS - SMT
9
9 - 46
Pin Number
Function
Description
1
VccLO
Supply for LO Amplifier.
Typically draws 109mA @ 2.8V.
2, 5, 8, 11,
12, 14, 17, 19,
20, 23
GND
These pins and the ground paddle should be
connected to a high quality RF/DC ground.
3
LOP
LO input. Need a DC decoupling capacitor.
Typically at 1.5 - 1.8 VDC.
4
LON
This pin should be AC grounded.
Also can be used to optimize the IP2
performances
6, 7, 24
N/C
Not Connected
9, 10
QN, QP
21, 22
IP, IN
Differential baseband outputs.
400 Ohms differential output impedance.
Each port should draw 38 mA @ 3.5V.
12, 19
VccQ, VccI
Decoupling for the Q and I mixer stages.
13, 18
CTRFQ, CTRFI
Center tap of the RF transformer. Should be
connected to a high quality RF/DC ground.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Pin Descriptions (Continued)
Pin Number
Function
Description
15
RFN
RF Input.
16
RFP
Can be DC or RF grounded. This pin is used to
match the RF port over the desired frequency
range. Also can be used to drive the RF port
differentially if needed.
Interface Schematic
DEMODULATORS - SMT
9
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 47
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Evaluation PCB
DEMODULATORS - SMT
9
Evaluation PCB 115775 [1][2]
Item
Description
J1 - J6
PCB Mount SMA Connector
J7, J8
2 mm DC Header
C11, C20 - C24
1000 pF Capacitor, 0402 Pkg.
C12
100 pF Capacitor, 0402 Pkg.
C25
0.3 pF Capacitor, 0402 Pkg.
C26
0.9 pF Capacitor, 0402 Pkg.
C30 - C32
0.1 μF Capacitor, 0805 Pkg.
R3, R4
39.2 Ohm Resistor, 0402 Pkg.
R5
18.2 Ohm Resistor, 0402 Pkg.
L1 - L4
5.6 nH Inductor, 0402 Pkg.
T1, T2
2 - 800 MHz Balun
U1
HMC597LP3 / HMC597LP3E
Direct Demodulator
PCB [2]
116265 Evaluation PCB
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[1] Reference this number when ordering complete evaluaiton PCB
[2] Circuit Board Material: Rogers 4350
9 - 48
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC597LP4 / 597LP4E
v03.0907
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Application & Evaluation PCB Schematic
DEMODULATORS - SMT
9
* Short to ground for single ended mode.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 49
Similar pages