HITTITE HMC689LP4_10

HMC689LP4 / 689LP4E
v01.1010
MIXERS - SINGLE & DOUBLE BALANCED - SMT
10
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Typical Applications
Features
The HMC689LP4(E) is Ideal for:
High Input IP3: +32 dBm
• Cellular/3G & LTE/WiMAX/4G
Low Conversion Loss: 7.5 dB
• Basestations & Repeaters
Low LO Drive: 0 dBm
• GSM, CDMA & OFDM
Optimized for High Side LO Input
• Transmitters and Receivers
Upconversion & Downconversion Applications
24 Lead 4x4mm SMT Package: 16mm2
Functional Diagram
General Description
The HMC689LP4(E) is a high dynamic range passive
MMIC mixer with integrated LO amplifier in a 4x4 SMT
QFN package covering 2.0 - 2.7 GHz. Excellent input
IP3 performance of +32 dBm for down conversion is
provided for 3G & 4G GSM/CDMA applications at an
LO drive of 0 dBm. With an input 1 dB compression
of +23 dBm, the RF port will accept a wide range of
input signal levels. Conversion loss is 7.5 dB typical.
The DC to 800 MHz IF frequency response will satisfy GSM/CDMA transmit or receive frequency plans.
The HMC689LP4(E) is pin for pin compatible with the
HMC688LP4(E) which is a 2.0 - 2.7 MHz mixer with
LO amplifier, amplifier is optimized for low side LO
applications.
Electrical Specifications,
TA = +25° C, IF = 300 MHz, LO = 0 dBm, Vcc = Vcc1, 2, 3 = +5V, G_Bias = +2.8V*
Parameter
Min.
Frequency Range, RF
Typ.
Max.
2.0 - 2.7
Units
GHz
Frequency Range, LO
2-3
GHz
Frequency Range, IF
DC - 800
MHz
Conversion Loss
7.5
Noise Figure (SSB)
7.5
11
dB
dB
LO to RF Isolation
26
34
dB
LO to IF Isolation
20
26
dB
RF to IF Isolation
24
30
dB
IP3 (Input)
32
dBm
1 dB Compression (Input)
23
dBm
LO Drive Input Level (Typical)
Supply Current (Icc total)
-3 to +3
152
dBm
185
mA
* Unless otherwise noted all measurements performed as downconverter with high side LO & IF = 300 MHz.
10 - 1
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Isolation
Conversion Gain vs. Temperature
0
RF/IF
LO/RF
LO/IF
-10
-10
+25 C
+85 C
-40 C
-15
-20
1.8
2
2.2
2.4
2.6
-30
-40
2.8
-50
1.8
3
2
2.2
2.4
2.6
2.8
3
2.8
3
2.8
3
FREQUENCY (GHz)
FREQUENCY (GHz)
Return Loss
Conversion Gain vs. LO Drive
0
0
RF
LO
-5
-5
RETURN LOSS (dB)
CONVERSION GAIN (dB)
10
-20
-10
-3 dBm
0 dBm
+3 dBm
-15
-20
1.8
2
2.2
2.4
2.6
-10
-15
-20
2.8
-25
1.8
3
2
2.2
2.4
2.6
FREQUENCY (GHz)
FREQUENCY (GHz)
Input P1dB vs. Temperature
IF Bandwidth (LO = 2.8 GHz)
0
30
-5
P1dB (dBm)
RESPONSE (dB)
25
-10
-15
20
-20
+25 C
+85 C
-40 C
15
IF Return Loss
Conversion Gain
-25
-30
0.1
0.2
0.3
0.4
0.5
0.6
FREQUENCY (GHz)
0.7
0.8
0.9
10
1.8
MIXERS - SINGLE & DOUBLE BALANCED - SMT
-5
ISOLATION (dB)
CONVERSION GAIN (dB)
0
2
2.2
2.4
2.6
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10 - 2
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Input IP3 vs. Temperature [1]
40
35
35
IP3 (dBm)
40
30
-3 dBm
0 dBm
+3 dBm
25
20
1.8
2
2.2
+25 C
+85 C
-40 C
25
2.4
2.6
2.8
20
1.8
3
2
2.2
2.6
2.8
3
-2RF +2LO Response vs. LO Drive [2]
90
-2RF+2LO RESPONSE (dBc)
90
-2RF+2LO RESPONSE (dBc)
2.4
FREQUENCY (GHz)
-2RF +2LO Response vs. Temperature [2]
80
70
60
+25 C
+85 C
-40 C
50
40
1.8
2
2.2
2.4
2.6
80
70
60
-3 dBm
0 dBm
+3 dBm
50
40
1.8
2.8
2
FREQUENCY (GHz)
2.2
2.4
2.6
2.8
FREQUENCY (GHz)
-3RF +3LO Response vs. Temperature [2]
-3RF +3LO Response vs. LO Drive [2]
90
-3RF+3LO RESPONSE (dBc)
90
+25 C
+85 C
-40 C
85
80
75
70
65
1.8
2
2.2
2.4
2.6
2.8
3
FREQUENCY (GHz)
[1] Two-tone input power = +9 dBm each tone, 1 MHz spacing.
10 - 3
30
FREQUENCY (GHz)
-3RF+3LO RESPONSE (dBc)
MIXERS - SINGLE & DOUBLE BALANCED - SMT
10
IP3 (dBm)
Input IP3 vs. LO Drive [1]
-3 dBm
0 dBm
+3 dBm
85
80
75
70
65
1.8
2
2.2
2.4
2.6
2.8
3
FREQUENCY (GHz)
[2] Referenced to RF Input power at 0 dBm
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Upconverter Performance
Conversion Gain vs. LO Drive
Upconverter Performance
Input IP3 vs. LO Drive [1]
32
30
-10
-6 dBm
-3 dBm
0 dBm
+3 dBm
-15
-20
1.8
2
2.2
2.4
10
28
26
-3 dBm
0 dBm
+3 dBm
24
2.6
2.8
3
22
1.8
2
Absolute Maximum Ratings
2.4
2.6
2.8
3
MxN Spurious @ IF Port
RF / IF Input (Vcc1, 2, 3 = +5V)
+23 dBm
LO Drive (Vcc1, 2, 3 = +5V)
+10 dBm
Vcc1, 2, 3
Channel Temperature
Continuous Pdiss (T = 85°C)
(derate 36.23 mW/°C above 85°C)
2.2
FREQUENCY (GHz)
FREQUENCY (GHz)
nLO
mRF
0
1
2
3
4
+5.5V
0
xx
23
34
34
38
125 °C
1
28
0
46
42
55
2
73
73
52
66
85
3
109
81
94
67
96
4
120
117
120
111
110
1.45 W
Thermal Resistance
(channel to ground paddle)
27.6 °C/W
Storage Temperature
-65 to 150 °C
Operating Temperature
-40 to +85 °C
Typical Supply Current vs. Vcc
Vcc1, 2, 3 (V)
Icc total (mA)
RF Freq. = 2.5 GHz @ 0 dBm
LO Freq. = 2.8 GHz @ 0 dBm
All values in dBc below IF power level (-1RF + 1LO).
Harmonics of LO
nLO Spur @ RF Port
4.75
140
LO Freq. (GHz)
1
2
3
4
5.00
152
2.1
32
26
55
29
5.25
164
2.2
30
26
51
30
2.3
29
27
42
29
Downconverter will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
2.4
28
26
44
29
2.5
26
25
41
26
2.6
25
24
42
26
2.7
24
23
42
22
2.8
25
24
40
26
2.9
26
22
38
34
MIXERS - SINGLE & DOUBLE BALANCED - SMT
-5
IP3 (dBm)
CONVERSION GAIN (dB)
0
LO = 0 dBm
All values in dBc below input LO level measured at RF port.
[1] Two-tone input power = +9 dBm each tone, 1 MHz spacing.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10 - 4
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Outline Drawing
MIXERS - SINGLE & DOUBLE BALANCED - SMT
10
10 - 5
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY.
3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN.
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
6. PAD BURR LENGTH SHALL BE 0.15mm MAX.
PAD BURR HEIGHT SHALL BE 0.25mm MAX.
7. PACKAGE WARP SHALL NOT EXCEED 0.05mm
8. ALL GROUND LEADS AND GROUND PADDLE
MUST BE SOLDERED TO PCB RF GROUND.
9. REFER TO HITTITE APPLICATION NOTE
FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC689LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC689LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H689
XXXX
H689
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Pin Descriptions
Pin Number
Description
N/C
No connection. These pins may be connected to RF
ground. Performance will not be affected.
2, 5, 15, 17
GND
Package bottom must be
connected to RF/DC ground.
3
RF
This pin is matched single-ended to 50 Ohms and DC
shorted to ground through a balun.
4
TAP
Center tap of secondary side of the internal RF balun.
Short to ground with zero ohms close to the IC.
8, 10, 24
Vcc1, Vcc2,
Vcc3
Power supply voltage. See application circuit
for required external components.
9
LO_BIAS
Adjust the LO buffer current through an external
resistor. See application circuit for required external
components.
16
LO
This pin is matched single-ended to 50 Ohms and DC
shorted to ground through a balun.
19
G_BIAS
External optional bias. See application circuit
for required external components. Apply +2.8V for
nominal performance
21, 22
IFN, IFP
Differential IF input / output pins matched to differential
50 Ohms. For applications not requiring operation to
DC, an off chip DC blocking capacitor should be used.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10
MIXERS - SINGLE & DOUBLE BALANCED - SMT
Function
1, 6, 7, 11 - 14,
18, 20, 23
10 - 6
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Evaluation PCB
MIXERS - SINGLE & DOUBLE BALANCED - SMT
10
List of Materials for Evaluation PCB 120974 [1]
Item
Description
J1 - J3
SMA Connector
J4 - J7
DC Pin
C1, C4
1.5 pF Capacitor, 0402 Pkg.
C7, C8, C13
10 nF Capacitor, 0402 Pkg.
C10, C12, C16, C18
1 nF Capacitor, 0402 Pkg.
C11, C15, C17, C21
0.1 µF Capacitor, 0402 Pkg.
C14, C19
22 pF Capacitor, 0402 Pkg.
L1
7.5 nH Inductor, 0402 Pkg
L2
8.2 nH Inductor, 0402 Pkg.
C20
4.7 µF Case A, Tantalum
R3, R4
0 Ohm Resistor, 0402 Pkg.
R9
215 Ohm Resistor, 0603 Pkg.
T1
1:1 Transformer - Tyco MABACT0039
U1
HMC689LP4(E) Downconverter
PCB [2]
118162 Evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. The
evaluation circuit board shown is available from Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25R, FR4
10 - 7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC689LP4 / 689LP4E
v01.1010
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 2.0 - 2.7 GHz
Application Circuit
MIXERS - SINGLE & DOUBLE BALANCED - SMT
10
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10 - 8