Hittite HMC734LP5 Mmic vco w/ divide-by-4 8.6 - 10.2 ghz Datasheet

HMC734LP5 / 734LP5E
v03.0609
MMIC VCO w/ DIVIDE-BY-4
8.6 - 10.2 GHz
Typical Applications
Features
The HMC734LP5(E) is ideal for:
Dual Output: Fo = 8.6 - 10.2 GHz
Fo/4 = 2.15 - 2.55 GHz
• Point-to-Point/Multi-Point Radio
• Test Equipment & Industrial Controls
Pout: +18 dBm
Phase Noise: -100 dBc/Hz @ 100 kHz Typ.
• SATCOM
No External Resonator Needed
• Military End-Use
32 Lead 5x5mm SMT Package: 25mm2
Functional Diagram
The HMC734LP5(E) is a GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCO. The
HMC734LP5(E) integrates a resonator, negative resistance device, varactor diode and features a divide-by-4
frequency output. The VCO’s phase noise performance is excellent over temperature, shock, and process due to the oscillator’s monolithic structure. Power
output is +18 dBm typical from a +5V supply voltage.
The prescaler function can be disabled to conserve
current if not required. The voltage controlled oscillator is packaged in a leadless QFN 5x5 mm surface
mount package, and requires no external matching
components.
8
VCOS - SMT
General Description
Electrical Specifications, TA = +25° C, Vcc (Dig), Vcc (Amp), Vcc (RF) = +5V
Parameter
Frequency Range
Power Output
Min.
Fo
Fo/4
Supply Current
RFOUT
RFOUT/4
15
-8
Vtune
1
-100
Icc(Dig) + Icc(Amp) + Icc(RF)
180
218
Output Return Loss (RFOUT)
Units
GHz
GHz
22
-1
Tune Port Leakage Current (Vtune= 13V)
dBm
dBm
dBc/Hz
13
V
240
mA
10
µA
8
dB
66
15
30
dBc
dBc
Pulling (into a 2.0:1 VSWR)
38
MHz pp
Pushing @ Vtune= 5V
30
MHz/V
Frequency Drift Rate
1.1
MHz/°C
Harmonics/Subharmonics
8-1
Max.
8.6 - 10.2
2.15 - 2.55
SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT
Tune Voltage
Typ.
1/2
2nd
3rd
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC734LP5 / 734LP5E
v03.0609
MMIC VCO w/ DIVIDE-BY-4
8.6 - 10.2 GHz
Frequency vs. Tuning Voltage, Vcc = +5V
Frequency vs. Tuning Voltage, T= 25°C
10.6
OUTPUT FREQUENCY (GHz)
11
10.6
10.2
10.2
9.8
9.4
9
8.6
+25C
+85C
-40C
8.2
7.8
7.4
9.8
9.4
9
8.6
8.2
4.75V
5.00V
5.25V
7.8
7.4
7
7
0
1
2
3
4
5
6
7
8
9
10
11 12
13
0
1
2
3
TUNING VOLTAGE (V)
6
7
8
9
10
11 12
13
Output Power
vs. Tuning Voltage, Vcc = +5V
25
700
500
OUTPUT POWER (dBm)
600
SENSITIVITY(MHz/V)
5
TUNING VOLTAGE (V)
Sensitivity vs. Tuning Voltage, Vcc = +5V
+25C
+85C
-40C
400
300
200
100
8
20
15
+25C
+85C
-40C
10
5
0
0
0
1
2
3
4
5
6
7
8
9
10
11 12
0
13
1
2
3
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (V)
Tuning Voltage (Volts)
SSB Phase Noise vs. Tuning Voltage
SSB Phase Noise @ Vtune = +5V
0
-60
-70
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
4
VCOS - SMT
OUTPUT FREQUENCY (GHz)
11
-80
10khz
100khz
-90
-20
-40
+25C
+85C
-40C
-60
-80
-100
-120
-100
-140
-110
-160
-120
0
1
2
3
4
5
6
7
8
9
TUNING VOLTAGE (VOLTS)
10
11 12
13
-180
2
10
3
10
4
10
5
10
6
10
7
10
TUNING VOLTAGE (VOLTS)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-2
HMC734LP5 / 734LP5E
v03.0609
MMIC VCO w/ DIVIDE-BY-4
8.6 - 10.2 GHz
Divide-by-4 Frequency
vs. Tuning Voltage, Vcc = +5V
Divide-by-4 Output Power
vs. Tuning Voltage, Vcc = +5V
-1
+25C
+85C
-40C
3.5
OUTPUT POWER (dBm)
OUTPUT FREQUENCY (GHz)
4
3
2.5
2
1.5
-2
-3
-4
-5
+25C
+85C
-40C
-6
1
-7
0
1
2
3
4
5
6
7
8
9
10
11 12
13
0
1
2
3
TUNING VOLTAGE (V)
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (V)
Outline Drawing
VCOS - SMT
8
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC734LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL3
[1]
HMC734LP5E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL3
[2]
Package Marking [3]
H734
XXXX
H734
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
8-3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC734LP5 / 734LP5E
v03.0609
MMIC VCO w/ DIVIDE-BY-4
8.6 - 10.2 GHz
Typical Supply Current vs. Vcc
Absolute Maximum Ratings
Vcc(Dig), Vcc(Amp), Vcc(RF)
+5.5 Vdc
Vcc (V)
Icc (mA)
Vtune
0 to +15V
4.75
198
Junction Temperature
135 °C
Continuous Pdiss (T=85 °C)
(derate 25.3 mW/C above 85 °C
1.3 W
Thermal Resistance
(junction to ground paddle)
39.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
5.00
218
5.25
237
Note: VCO will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Pin Descriptions
Function
Description
N/C
No Connection. These pins may be connected to RF/
DC ground. Performance will not be affected.
4
RFOUT/4
Divide-by-4 output. DC block required.
6
Vcc (Dig)
Supply voltage for prescaler. If prescaler is not
required, this pin may be left open to conserve
approximately 100 mA of current.
19
RFOUT
RF output (AC coupled).
21
Vcc (RF)
Supply Voltage, +5V
29
VTUNE
Control voltage and modulation input. Modulation
bandwidth dependent on drive source impedance.
See “Determining the FM Bandwidth of a Wideband
Varactor Tuned VCO” application note.
5, 11, 18,
Paddle
GND
Package bottom has an exposed metal paddle that
must be connected to RF/DC ground.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8
VCOS - SMT
Pin Number
1 - 3, 7 - 10,
12 - 17, 20,
22 - 28, 30 - 32
8-4
HMC734LP5 / 734LP5E
v03.0609
MMIC VCO w/ DIVIDE-BY-4
8.6 - 10.2 GHz
Application Circuit
VCOS - SMT
8
8-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC734LP5 / 734LP5E
v03.0609
MMIC VCO w/ DIVIDE-BY-4
8.6 - 10.2 GHz
Evaluation PCB
VCOS - SMT
8
List of Materials for Evaluation PCB 110227 [1]
Item
Description
J1 - J4
PCB Mount SMA RF Connector
J5 - J6
2 mm DC Header
C1 - C3
100 pF Capacitor, 0402 Pkg.
C4
1,000 pF Capacitor, 0402 Pkg.
C5 - C7
2.2 µF Tantalum Capacitor
U1
HMC734LP5(E) VCO
PCB [2]
110225 Eval Board
[1] Reference this number when ordering complete evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and backside ground paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-6
Similar pages