Hynix HMP525F7FFP4C-Y5N3 240pin fully buffered ddr2 sdram dimms based on 512 mb f-ver. Datasheet

240pin Fully Buffered DDR2 SDRAM DIMMs based on 512 Mb F-ver.
This Hynix’s Fully Buffered DIMM is a high-bandwidth & large capacity channel solution that has a narrow
host interface. Hynix’s FB-DIMM features novel architecture including the Advanced Memory Buffer that
isolates the DDR2 SDRAMs from the channel. This single component located in the front side center of
each DIMM, acts as a repeater and buffer for all signals and commands which are exchanged between the
host controller and the DDR2 SDRAMs including data in and output. The AMB communicates with the host
controller and adjacent DIMMs on a system board using an industry standard Differential Point to Point
Link Interface at 1.5V power.
The AMB also allows buffering of memory traffic to support large memory capacities. All memory control
for the DDR2 SDRAM devices resides in the host, including memory request initiation, timing, refresh,
scrubbing, sparing, configuration access and power management. The AMB interface is responsible for
handling channel and memory requests to and from the local FBDIMM and for forwarding request to other
FBDIMMs on the memory channel.
FEATURES
•
240 pin Fully Buffered ECC dual In-Line DDR2 SDRAM Module
•
JEDEC standard Double Data Rate2 Synchronous DRAMs (DDR2 SDRAMs) with 1.8V +/- 0.1V Power Supply
•
All inputs and outputs are compatible with SSTL_1.8 interface
•
Built with 512Mb DDR2 SDRAMs in 60ball FBGA
•
Host interface and AMB component industry standard compliant
•
MBIST & IBIST test functions
•
4 Bank architecture
•
OCD (Off-Chip Driver Impedance Adjustment)
•
ODT (On-Die Termination)
•
Fully differential clock operations (CK & CK)
•
Programmable Burst Length 4 / 8 with both sequential and interleave mode
•
Auto refresh and self refresh supported
•
8192 refresh cycles / 64ms
•
Serial presence detect with EEPROM
•
133.35 x 30.35 mm form factor
•
RoHS compliant
•
Full Module Heat Spreader
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev 1.2 / Feb. 2009
1
1240pin Fully Buffered DDR2 SDRAM DIMMs
ORDERING INFORMATION
Part Name
Density
HMP564F7FFP8C-C4/Y5N3
HMP564F7FFP8C-C4/Y5/S5/S6D3
Org.
# of
# of
DRAMs ranks
512MB
64Mx72
9
1
1GB
128Mx72
18
2
2GB
256Mx72
36
2
HMP512F7FFP8C-C4/Y5N3
HMP512F7FFP8C-C4/Y5/S5/S6D3
HMP525F7FFP4C-C4/Y5N3
HMP525F7FFP4C-C4/Y5D3
AMB
H. S
type
Height
Full
Module
30.35mm
Vendor Version
Intel
D1
IDT
C1
Intel
D1
IDT
C1
Intel
D1
IDT
C1
Note:
*: The 16th and 17th digits stand for AMB vendor and revision.
SPEED GRADE & KEY PARAMETERS
Speed Grade
C4
Y5
S5/6
DDR2 533 4-4-4
DDR2 667 5-5-5
DDR2 800 5-5-5 / 6-6-6
PC2 4200
PC2 5300
PC2 6400
FB-DIMM Peak Channel Throughput
6.4
8.0
9.6
GByte/S
FB-DIMM Link Transfer Rate
3.2
4.0
4.8
GT/s
DDR2 DRAM Speed Grade
FB-DIMM Speed Grade
Unit
ADDRESS TABLE
Density
Org.
Ranks
SDRAMs
# of
DRAMs
512MB
64M x 72
1
64Mbx8
9
14(A0~A13)/2(BA0~BA1)/10(A0~A9)
8K / 64ms
1GB
128M x 72
2
64Mbx8
18
14(A0~A13)/2(BA0~BA1)/10(A0~A9)
8K / 64ms
2GB
256M x 72
2
128Mbx4
36
14(A0~A13)/2(BA0~BA1) 11(A0~A9,A11)
8K / 64ms
Rev 1.2 / Feb. 2009
# of row/bank/column Address
Refresh
Method
2
1240pin Fully Buffered DDR2 SDRAM DIMMs
Input/Output Functional Description
Pin Name
type
Polarity
SCK
Input
Positive
System clock input
1
SCK
Input
Negative
System clock input
1
PN[13:0]
Output
Positive
Primary Northbound Data
14
PN[13:0]
Output
Negative
Primary Northbound Data
14
PS[9:0]
Input
Positive
Primary Southbound Data
10
PS[9:0]
Input
Negative
Primary Southbound Data
10
SN[13:0]
Output
Positive
Secondary Northbound Data
14
SN[13:0]
Output
Negative
Secondary Northbound Data
14
SS[9:0]
Input
Positive
Secondary Southbound Data
10
SS[9:0]
Input
Negative
Secondary Southbound Data
10
SCL
Input
-
Serial Presence Detect (SPD) Clock Input
1
SDA
Input / Output
-
SPD Data Input / Output
1
SA[2:0]
Input
-
SPD Address inputs, also used to select the DIMM number in the AMB
3
VID[1:0]
Input
-
Voltage ID:
These pins must be unconnected for DDR2-based Fully buffered DIMMs
2
RESET
Input
Active Low
AMB reset signal
1
RFU
-
-
Reserved for Future Use
16
VCC
Supply
+1.5V
AMB Core Power and AMB channel Interface Power(1.5volt)
8
VDD
Supply
+1.8V
DRAM Power and AMB DRAM I/O Power
24
VTT
Supply
+0.9V
DRAM Address/Command/Clock Termination Power(VDD/2)
4
VDDSPD
Supply
+3.3V
SPD Power
1
VSS
Supply
Ground
80
The DNU/M_Test pin provides an external connection on R/Cs A-D for
testing the margin of Vref which is produced by a voltage divider on the
module. It is not intended to be used in normal system operation and
must not be connected(DNU) in a system. This test pin may have other
features on future card designs and if it does, will be included in this
specification at that time.
1
Total
240
DNU/
M_Test
- / Analog
Rev 1.2 / Feb. 2009
- / 0.9V
Function Description
Count
3
1240pin Fully Buffered DDR2 SDRAM DIMMs
PIN ASSIGNMENT
Pin
Name
Pin
Name
Pin
Name
Pin
Name
Pin
Name
Pin
Name
1
VDD
41
PN13
81
VSS
121
VDD
161
SN13
201
VSS
2
VDD
42
VSS
82
PS4
122
VDD
162
VSS
202
SS4
3
VDD
43
VSS
83
PS4
123
VDD
163
VSS
203
SS4
4
VSS
44
RFU*
84
VSS
124
VSS
164
RFU*
204
VSS
5
VDD
45
RFU*
85
VSS
125
VDD
165
RFU*
205
VSS
6
VDD
46
VSS
86
RFU*
126
VDD
166
VSS
206
RFU*
7
VDD
47
VSS
87
RFU*
127
VDD
167
VSS
207
RFU*
8
VSS
48
PN12
88
VSS
128
VSS
168
SN12
208
VSS
9
VCC
49
PN12
89
VSS
129
VCC
169
SN12
209
VSS
10
VCC
50
VSS
90
PS9
130
VCC
170
VSS
210
SS9
11
VSS
51
PN6
91
PS9
131
VSS
171
SN6
211
SS9
VSS
12
VTT
52
PN6
92
VSS
132
VCC
172
SN6
212
13
VCC
53
VSS
93
PS5
133
VCC
173
VSS
213
SS5
14
VSS
54
PN7
94
PS5
134
VSS
174
SN7
214
SS5
15
VTT
55
PN7
95
VSS
135
VTT
175
SN7
215
VSS
16
VID1
56
VSS
96
PS6
136
VID0
176
VSS
216
SS6
17
RESET
57
PN8
97
PS6
137
DNU/M_Test
177
SN8
217
SS6
18
VSS
58
PN8
98
VSS
138
VSS
178
SN8
218
VSS
19
RFU**
59
VSS
99
PS7
139
RFU**
179
VSS
219
SS7
20
RFU**
60
PN9
100
PS7
140
RFU**
180
SN9
220
SS7
21
VSS
61
PN9
101
VSS
141
VSS
181
SN9
221
VSS
22
PN0
62
VSS
102
PS8
142
SN0
182
VSS
222
SS8
23
PN0
63
PN10
103
PS8
143
SN0
183
SN10
223
SS8
24
VSS
64
PN10
104
VSS
144
VSS
184
SN10
224
VSS
25
PN1
65
VSS
105
RFU**
145
SN1
185
VSS
225
RFU*
26
PN1
66
PN11
106
RFU**
146
SN1
186
SN11
226
RFU*
27
VSS
67
PN11
107
VSS
147
VSS
187
SN11
227
VSS
28
PN2
68
VSS
108
VDD
148
SN2
188
VSS
228
SCK
29
PN2
109
VDD
149
SN2
229
SCK
30
VSS
69
VSS
110
VSS
150
VSS
189
VSS
230
VSS
31
PN3
70
PS0
111
VDD
151
SN3
190
SS0
231
VDD
Key
Key
32
PN3
71
PS0
112
VDD
152
SN3
191
SS0
232
VDD
33
VSS
72
VSS
113
VDD
153
VSS
192
VSS
233
VDD
34
PN4
73
PS1
114
VSS
154
SN4
193
SS1
234
VSS
35
PN4
74
PS1
115
VDD
155
SN4
194
SS1
235
VDD
VDD
36
VSS
75
VSS
116
VDD
156
VSS
195
VSS
236
37
PN5
76
PS2
117
VTT
157
SN5
196
SS2
237
VTT
38
PN5
77
PS2
118
SA2
158
SN5
197
SS2
238
VDDSPD
39
VSS
78
VSS
119
SDA
159
VSS
198
VSS
239
SA0
40
PN13
79
PS3
120
SCL
160
SN13
199
SS3
240
SA1
80
PS3
200
SS3
NC= No Connect, RFU= Reserved for Future Use.
Note:
*: These pin positions are reserved for forwarded clocks to be used in future module implementations
**: These pin positions are reserved for future architecture flexibility
1) The following signals are CRC bits and thus appear out of the normal sequence:
PN12/ PN12, SN12 / SN12, PN13 / PN13, SN13 / SN13,PS9 / PS9, SS9 / SS9
Rev 1.2 / Feb. 2009
4
1240pin Fully Buffered DDR2 SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
512MB(64Mbx72) ECC FB-DIMM
/S0
DQS4
/DQS4
DQS13
DQS0
/DQS0
DQS9
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
DQS
/DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
DQS
/DQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D1
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
DQS
/DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D2
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
DQS
/DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D3
All address/command/control/clock
V TT
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
WP
SDA
U0
A0
A1
SA0 SA1
DQS
/DQS
DQS
/DQS
DQS
/DQS
D5
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D6
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D7
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D8
Serial PD
SCL
/DQS
DQS8
/DQS8
DQS17
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
SCL
DQS
D4
DQS7
/DQS7
DQS16
DQS3
/DQS3
DQS12
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
3
4
5
6
7
/DQS
DQS6
/DQS6
DQS15
DQS2
/DQS2
DQS11
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
I/O
I/O
I/O
I/O
I/O
DQS
DQS5
/DQS5
DQS14
DQS1
/DQS1
DQS10
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DM
NU /CS
RDQS /RDQS
I/O 0
I/O 1
I/O 2
A2
SA2
SDA
VTT
Terminators
VCC
AMB
VDD SPD
Serial PD,AMB
VDD
DO-D8, AMB
VREF
DO-D8
VSS
DO-D8,SPD, AMB
PN0-PN13
/PN0-/PN13
PS0-PS9
/PS0-/PS9
DQ0-DQ63
CB0-CB7
DQS0-DQS17
/DQS0-/DQS8
SCL
SDA
SA0-SA2
/RESET
SCK/ /SCK
A
M
B
SN0-SN13
/SN0-/SN13
SS0-SS9
/SS0-/SS9
/S0-/CS(all SDRAMs)
CKE0 -> CKE
ODT -> ODT
BA0-BA2
A0-A15
/RAS
/CAS
/WE
CK/ /CK
Notes :
1. DQ-to-I/O wiring may be changed within a byte.
2. There are two physical copies of each address/command/control/clock.
Rev 1.2 / Feb. 2009
5
1240pin Fully Buffered DDR2 SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
1GB(128Mbx72) ECC FB-DIMM
/S 1
/S 0
DQS
/D Q S
DQS9
DQS5
/D Q S 5
D Q S14
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQS1
/D Q S 1
D Q S 10
I/O
I/ O
I/O
I/O
I/O
D Q S /D Q S
D0
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
I/ O
I/O
I/ O
I/ O
I/ O
3
4
5
6
7
D Q S /D Q S
D Q 40
D Q 41
D Q 42
D Q 43
D Q 44
D Q 45
D Q 46
DQ 47
D9
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D Q S /D Q S
D5
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D Q S /D Q S
D 14
DQ S6
/D Q S 6
DQ S15
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
DQ8
DQ 9
D Q 10
D Q 11
D Q 12
D Q 13
D Q 14
DQ 15
I/O
I/ O
I/O
I/O
I/O
D Q S /D Q S
D1
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
I/ O
I/O
I/ O
I/ O
I/ O
3
4
5
6
7
D Q S /D Q S
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
D Q 55
D1 0
z
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D Q S /D Q S
D6
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D Q S /D Q S
D 15
DQS7
/D Q S 7
DQ S16
DQS2
/D Q S 2
DQ S11
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
D Q16
D Q17
D Q18
D Q19
D Q20
D Q21
D Q22
D Q 23
I/ O
I/O
I/ O
I/ O
I/ O
D Q S /D Q S
D2
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
D Q S /D Q S
D Q 56
D Q 57
D Q 58
D Q 59
D Q 60
D Q 61
D Q 62
D Q 63
D1 1
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D Q S /D Q S
D7
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
I/ O
I/O
I/ O
I/ O
I/ O
3
4
5
6
7
D Q S /D Q S
D 16
DQS8
/D Q S 8
D Q S17
DQS3
/D Q S 3
D Q S12
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
D Q24
D Q25
D Q26
D Q27
D Q28
D Q29
D Q30
D Q 31
I/ O
I/O
I/ O
I/ O
I/ O
D Q S /D Q S
D3
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
D Q S /D Q S
C B0
C B1
C B2
C B3
C B4
C B5
C B6
C B7
D1 2
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
I/O
I/O
I/O
I/O
I/O
3
4
5
6
7
D Q S /D Q S
D8
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
I/ O
I/O
I/ O
I/ O
I/ O
3
4
5
6
7
D Q S /D Q S
D 17
DQS4
/D Q S 4
D Q S 13
DM
N U /C S
R D Q S /R D Q S
I/O 0
I/O 1
I/O 2
D Q32
D Q33
D Q34
D Q35
D Q36
D Q37
D Q38
DQ 39
I/O
I/ O
I/O
I/O
I/O
D Q S /D Q S
D4
3
4
5
6
7
DM
N U /C S
R D Q S /R D Q S
I/ O 0
I/ O 1
I/ O 2
I/ O
I/O
I/ O
I/ O
I/ O
3
4
5
6
7
A ll a d d re s s/ c o m m a n d /c o n tro l/c lo c k
S e ria l P D
SCL
SCL
WP
SDA
U0
A0
A1
A2
SA0
SA1
SA2
SDA
D Q S /D Q S
D 13
P N 0 -P N 1 3
/P N 0 -/P N 1 3
P S 0 -P S 9
/P S 0 -/P S 9
V TT
VTT
T e rm in a to rs
VCC
AMB
VDD SPD
S e ria l P D ,A M B
VDD
D O -D 1 7 , A M B
VREF
D O -D 1 7
VSS
D Q 0 -D Q 6 3
C B 0 -C B 7
D Q S 0 -D Q S 1 7
/D Q S 0 -/D Q S 8
D O -D 1 7 ,S P D , A M B
SCL
SDA
S A 0 -S A 2
/R ES ET
S C K , /S C K
A
M
B
S N 0 -S N 1 3
/S N 0 -/S N 1 3
S S 0 -S S 9
/S S 0 -/S S 9
/S 0 -/ C S (D 0 -D 8 )
C K E 0 -> C K E (D 0 -D 8 )
/S 1 -/ C S (D 9 -D 1 7 )
C K E 1 -> C K E (D 9 -D 1 7 )
O D T -> O D T (a ll S D R A M s )
B A 0 -B A 2 (a ll S D R A M s )
A 0 -A 1 5 (a ll S D R A M s )
/R A S (a ll S D R A M s )
/C A S (a ll S D R A M s )
/W E (a ll S D R A M s )
C K , /C K (a ll S D R A M s )
Notes :
1. DQ-to-I/O wiring may be changed within a byte.
2. There are two physical copies of each address/command/control/clock.
Rev 1.2 / Feb. 2009
6
1240pin Fully Buffered DDR2 SDRAM DIMMs
FUNCTIONAL BLOCK DIAGRAM
2GB(256Mbx72) ECC FB-DIMM
VSS
/S1
/S0
/DQS9
DQS9
/DQS0
DQS0
DQ0
DQ1
DQ2
DQ3
/DQS1
DQS1
DQ 8
DQ 9
DQ 10
DQ 11
/DQS2
DQS2
DQ 16
DQ 17
DQ 18
DQ 19
/DQS3
DQS3
DQ 24
DQ 25
DQ 26
DQ27
/DQS4
DQS4
DQ 32
DQ 33
DQ 34
DQ 35
/DQS5
DQS5
DQ 40
DQ 41
DQ 42
DQ43
/DQS6
DQS6
DQ 48
DQ 49
DQ 50
DQ51
/DQS7
DQS7
DQ 56
DQ 57
DQ 58
DQ59
/DQS8
DQS8
CB0
CB1
CB2
CB3
DQS /DQS /CS
I/O 0
I/O 1
D0
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
I/O 2 D18
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D1
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
I/O 2 D19
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D2
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D20
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D3
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D21
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D4
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D22
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D5
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D23
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D6
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
I/O 2 D24
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D7
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D25
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D8
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
I/O 2 D26
I/O 3
DM
All address/command/control/clock
Serial PD
SCL
SCL
WP
U0
A0 A1
SDA
A2
SA0 SA1 SA2
SDA
DQ4
DQ5
DQ6
DQ7
/DQS10
DQS10
DQ20
DQ21
DQ22
DQ23
/DQS11
DQS11
DQ36
DQ37
DQ38
DQ39
/DQS12
DQS12
DQ44
DQ45
DQ46
DQ47
/DQS13
DQS13
DQ52
DQ53
DQ54
DQ55
/DQS14
DQS14
DQ60
DQ61
DQ62
DQ63
/DQS15
DQS15
DQ64
DQ65
DQ66
DQ67
/DQS16
DQS16
DQ60
DQ61
DQ62
DQ63
/DQS17
DQS17
CB4
CB5
CB6
CB7
V TT
VTT
Terminators
VCC
AMB
DQS /DQS /CS
I/O 0
I/O 1
D9
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D27
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D10
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D28
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D11
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D29
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D12
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D30
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D13
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D31
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D14
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D32
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D15
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D33
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D16
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D34
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D17
I/O 2
I/O 3
DM
DQS /DQS /CS
I/O 0
I/O 1
D35
I/O 2
I/O 3
DM
PN0-PN13
/PN0-/PN13
PS0-PS9
/PS0-/PS9
VDD
DQ0-DQ63
Serial PD,AMB
CB0-CB7
DQS0-DQS17
DO-D35, AMB /DQS0-/DQS17
VREF
DO-D35
VDD SPD
VSS
DO-D35,SPD, AMB
SCL
SDA
SA0-SA2
/RESET
SCK, /SCK
A
M
B
SN0-SN13
/SN0-/SN13
SS0-SS9
/SS0-/SS9
/S0-/CS (all SDRAMs)
CKE0 -> CKE (all SDRAMs)
ODT -> ODT (all SDRAMs)
BA0-BA2 (all SDRAMs)
A0-A15 (all SDRAMs)
/RAS (all SDRAMs)
/CAS (all SDRAMs)
/W E (all SDRAMs)
CK, /CK (all SDRAMs)
Notes :
1. DQ-to-I/O wiring may be changed within a byte.
2. There are two physical copies of each address/command/control/clock.
Rev 1.2 / Feb. 2009
7
1240pin Fully Buffered DDR2 SDRAM DIMMs
Architecture
Advanced Memory Buffer Pin Description
Pin Name
Pin Description
FB-DIMM Channel Signals
Count
99
SCK
System Clock Input, positive line
1
SCK
System Clock Input, negative line
1
PN[13:0]
Primary Northbound Data, positive lines
14
PN[13:0]
Primary Northbound Data, negative lines
14
PS[9:0]
Primary Southbound Data, positive lines
10
PS[9:0]
Primary Southbound Data, negative lines
10
SN[13:0]
Secondary Northbound Data, positive lines
14
SN[13:0]
Secondary Northbound Data, negative lines
14
SS[9:0]
Secondary Southbound Data, positive lines
10
SS[9:0]
Secondary Southbound Data, negative lines
10
FBDRES
To an external precision calibration resistor connected to Vcc
1
DDR2 Interface Signals
DQS[8:0]
175
Data Strobes, positive lines
9
DQS[8:0]
Data Strobes, negative lines
9
DQS[17:9]/DM[8:0]
Data Strobes(x4 DRAM only), positive lines. These signals are driven low to x8
DRAM on writes.
9
DQS[17:9]
Data Strobes(x4 DRAM only), negative lines
9
DQ[63:0]
Data
64
CB[7:0]
Checkbits
8
A[15:0]A,A[15:0]B
Addresses. A10 is part of the pre-charge command
32
BA[2:0]A,BA[2:0]B
Bank Addresses
6
RASA,RASB
Part of command, with CAS, WE and CS[1:0]
2
CASA,CASB
Part of command, with RAS, WE and CS[1:0]
2
WEA,WEB
Part of command, with RAS, WE and CS[1:0]
2
ODTA,ODTB
On-die Termination Enable
2
CKE[1:0]A,CKE[1:0]B
Clock Enable(one per rank)
4
CS[1:0]A,CS[1:0]B
Chip Select(One per rank)
4
CLK[3:0]
CLK[1:0] used on 9 and 18 device DIMMs, CLK[3:0] used on 36 device DIMMs.
CLK[3:2] should be output disabled when not in use.
4
CLK[3:0]
Negative lines for CLK[3:0]
4
DDRC_C14
DDR Compensation: Common return pin for DDRC_B18 and DDRC_C18
1
DDRC_B18
DDR Compensation: Resistor connected to common return pin DDRC_C14
1
DDRC_C18
DDR Compensation: Resistor connected to common return pin DDRC_C14
1
DDRC_B12
DDR Compensation: Resistor connected to VSS
1
DDRC_C12
DDR Compensation: Resistor connected to VDD
1
Rev 1.2 / Feb. 2009
8
1240pin Fully Buffered DDR2 SDRAM DIMMs
Advanced Memory Buffer Pin Description
Pin Name
Pin Description
Count
SPD Bus Interface Signals
5
SCL
Serial Presence Detect (SPD) Clock Input
1
SDA
SPD Data Input / Output
1
SA{2:0]
SPD Address Inputs, also used to select the DIMM number in the AMB
3
Miscellaneous Signals
163
PLLTSTO
PLL Clock Observability Output
1
VCCAPLL
Analog VCC for the PLL. Tied with low pass filter to VCC.
1
VSSAPLL
Analog VSS for the PLL. Tied to
1
TEST_pin#
Leave floating on the DIMM
6
TESTLO_pin#
Tie to ground on the DIMM2
5
BFUNC
Tie to ground to set functionality as “buffer on DIMM.”
1
RESET
AMB reset signal
1
NC
No connect. Many NC are connected to VDD on the DIMM, to lower the impedance
of the VDD power islands.
129
RFU
Reserved for Future Use
18
Power/Ground Signals
213
VCC
AMB Core Power(1.5 Volt)
24
VCCFBD
AMB Channel I/O Power(1.5 Volt)
8
VDD
AMB DRAM I/O Power (1.8 Volt)
24
VDDSPD
SPD Power (3.3 Volt)
1
VSS
Ground
156
Total
655
Note:
1. System Clock Signals SCK and SCK switch at one half the DRAM CK/ CK frequency.
2. TESTLO_AB20 and TESTLO_AC20 should be configured for debug purposes on protype DIMMs:
each pin should have a zero ohm resistor pull-down to ground, and an unpopulated resistor pull-up to VCC.
These resistors can be replaced on production DIMMs with a direct connection to ground.
Rev 1.2 / Feb. 2009
9
1240pin Fully Buffered DDR2 SDRAM DIMMs
Pin Assignments for the Advanced Memory Buffer(AMB) (Top View)
655-Ball LFBGA 0.8 mm x 0.8 mm pitch
Left Side
1
2
3
VDD
A
B
4
5
6
7
VSS
DQ26
DQ12
DQS3
DQS3
VSS
DQ14 DQS10
VDD
8
DQS10 DQ13
9
10
11
12
13
14
15
VDD
DQS1
DQ10
VDD
TEST
VDD
VDD
VSS
DQ11
DQS1
VSS
DDRC
TESTLO
VDD
VSS
C
VSS
DQS2
DQ18
VSS
DQ4
DQS9
VSS
DQ15
DQ9
VSS
DQ8
DDRC
VSS
D
DQ19
DQS2
VSS
DQ16
DQ24
VSS
DQS9
DQ7
VSS
DQ3
DQS0
VSS
DQS8
E
DQ21
VSS
DQ17
DQ29
VSS
DQ25
DQ6
VSS
DQ5
DQ1
VSS
DQ0
CB1
VSS
CB2
F
VSS
DQ20
DQ23
VSS
DQ31
DQ27
VSS
TESTLO TEST
VSS
DQS0
DQ2
VDD
CB0
CB3
G
DQS11 DQS11
NC
NC
NC
VSS
H
DQ22
VSS
NC
NC
NC
DQ28
DDRC DQS17
DQS8
VDD
DQS12 DQS12
NC
NC
NC
BFUNC
RFU
RFU
RFU
DQ30
VSS
NC
NC
NC
VSS
VDD
VSS
VDD
J
VSS
CLK2
NC
NC
NC
BA1A
VSS
CKE1A
NC
NC
NC
VDD
VSS
VDD
VSS
K
CLK2
CLK0
NC
NC
NC
VSS
WEA
RASA
NC
NC
NC
VSS
VCC
VSS
VCC
L
CLK0
VSS
NC
NC
NC
A0A
CKE0A
VSS
NC
NC
NC
VCC
VSS
VCC
VSS
M
ODT0A
RFU
NC
NC
NC
CASA
VSS
BA2A
NC
NC
NC
VSS
VCC
VSS
VCC
N
CS1A
CS0A
NC
NC
NC
VSS
BA0A
A10A
NC
NC
NC
VCC
VSS
VCC
VSS
P
A6A
VSS
NC
NC
NC
A2A
A1A
A3A
NC
NC
NC
VSS
VCC
VSS
VCC
R
VSS
A8A
NC
NC
NC
A11A
VSS
A5A
NC
NC
NC
VCC
VSS
VCC
VSS
T
A4A
A13A
NC
NC
NC
VSS
A9A
A7A
NC
NC
NC
VSS
VCC
VSS
VCC
U
PN0
PN0
NC
NC
NC
A15A
A14A
A12A
NC
NC
NC
RFU
VCCFBD
VSS
VSS
VSS
RFUa
RFUa
VCCFBD
VSS
VSS
VSS
V
PN1
PN1
VSS
SN0
SN0
VCCFBD
VSS
VCCFBD
W
PN2
PN2
VSS
SN1
SN1
SN3
SN4
SN5
SN13
SN12
SN6
SN7
SN8
SN9
SN10
Y
PN3
PN3
VSS
SN2
SN0
SN3
SN4
SN6
SN13
SN12
SN6
SN7
SN8
SN9
SN10
AA
VSS
PN4
PN4
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
RESET
PN5
PN13
RFUa
PN12
PN6
PN7
PN8
PN9
VSSAPLL VCCAPLL PN10
PN11
a
FBDRES PLLTSTO PN10
PN11
AB
AC
1
2
VSS
PN5
PN13
RFU
PN12
PN6
PN7
PN8
PN9
3
4
5
6
7
8
9
10
11
12
13
14
15
NC= No Connect, RFU= Reserved for Future Use.
Note:
a. These pin positions are reserved for forwarded clocks to be used in future AMB implementations
Rev 1.2 / Feb. 2009
10
1240pin Fully Buffered DDR2 SDRAM DIMMs
Right Side
A
16
17
18
19
20
21
22
23
24
25
26
27
VDD
TEST
VDD
DQ52
DQS15
VDD
DQ49
DQS6
VDD
DQ48
DQ38
VDD
28
B
VDD
TEST
DDRC
VSS
DQS15
DQ53
VSS
DQS6
DQ50
VSS
DQS13
DQS13
VSS
C
DQS17
VSS
DDRC
DQ54
VSS
DQ55
DQ51
VSS
DQS7
DQ56
VSS
DQ46
DQS14
D
CB6
CB7
VSS
DQS16
DQ63
VSS
DQ59
DQS7
VSS
DQ36
DQ44
VSS
E
VSS
CB5
DQS16
VSS
DQ61
DQ57
VSS
DQ58
DQ39
VSS
DQ33
DQ45
29
VDD
DQS14 DQ47
VSS
DQ41
F
CB4
VDD
DQ62
DQ60
VSS
TEST
TEST
VSS
DQ37
DQ35
VSS
DQS5
DQ43
VSS
G
TESTLO
RFU
RFU
NC
NC
NC
DQS4
DQS4
VSS
NC
NC
NC
DQS5
DQ40
H
VSS
VDD
VSS
NC
NC
NC
VSS
DQ34
DQ32
NC
NC
NC
VSS
DQ42
J
VDD
VSS
VDD
NC
NC
NC
RASB
VSS
RFU
NC
NC
NC
CLK3
VSS
K
VSS
VCC
VSS
NC
NC
NC
ODT0B
CS1B
VSS
NC
NC
NC
CLK1
CLK3
L
VCC
VSS
VCC
NC
NC
NC
VSS
CASB
WEB
NC
NC
NC
VSS
CLK1
M
VSS
VCC
VSS
NC
NC
NC
CS0B
VSS
BA1B
NC
NC
NC
CKE0B
VSS
N
VCC
VSS
VCC
NC
NC
NC
A0B
A2B
VSS
NC
NC
NC
BA0B
BA2B
P
VSS
VCC
VSS
NC
NC
NC
VSS
A4B
A1B
NC
NC
NC
VSS
CKE1B
R
VCC
VSS
VCC
NC
NC
NC
A6B
VSS
A10B
NC
NC
NC
A3B
VSS
T
VSS
VCC
VSS
NC
NC
NC
A11B
A9B
VSS
NC
NC
NC
A7B
A5B
U
VSS
VCCFBD
RFU
NC
NC
NC
A8B
A15B
A14B
SA0
SCL
SDA
PS8
PS8
VSS
A13B
A12B
SA2
SA1
PS7
PS7
V
VCCFBD
VSS
VCCFBD
VSS
VCCFBD
RFU
RFUa
W
VSS
SS0
SS1
SS2
SS3
SS4
SS9
SS5
SS6
SS7
SS8
VSS
PS6
PS6
Y
VSS
SS0
SS1
SS2
SS3
SS4
SS9
SS5
SS6
SS7
SS8
VSS
PS5
PS5
AA
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
PS9
PS9
VSS
PS4
RFUa
VDDSPD
VSS
a
AB
AC
VSS
SN11
VSS
SCK
TESTLO
a
PS0
PS1
PS2
PS3
RFU
SN11
VSS
SCK
TESTLO
PS0
PS1
PS2
PS3
PS4
RFU
16
17
18
19
20
21
22
23
24
25
26
VSS
27
28
29
NC= No Connect, RFU= Reserved for Future Use.
Note:
a. These pin positions are reserved for forwarded clocks to be used in future AMB implementations
Rev 1.2 / Feb. 2009
11
1240pin Fully Buffered DDR2 SDRAM DIMMs
Advanced Memory Buffer(AMB) DRAM Interface Specifications
Please refer to the AMB Specification for all technical requirements
The following specifications for the AMB constitute the subset which is critical for proper operation of the
DDR2 SDRAM interface.
Note:
This list is not complete, more information will follow in later revisions of this specification.
Critical AMB Specifications
Symbol
Parameter
Type
VDDQ =1.8V +/-0.1V
Min
Max
Units Notes
tSU
DQ to DQS, DQS setup time (read)
Input
245
ps
1
tH
DQ to DQS, DQS hold time (read)
Input
245
ps
1
tDVBamb
AMB Data Valid Before DQS
Output
470
ps
1
tDVAamb
AMB Data Valid After DQS
Output
470
ps
1
tCVBamb
C/A/CNTL Valid Before Clock
Output
1030
ps
1
tCVAamb
C/A/CNTL Valid After Clock
Output
890
ps
1
tDQSCKamb
DQS/DQS-to-CK/CK output skew
Output
-240
240
ps
1
CIN
Input Capacitance(DQ/DQS/DQS)
2.0
2.5
pF
1
Note 1:
The timing numbers are for example only. Design should be based on the latest component specifications
Rev 1.2 / Feb. 2009
12
1240pin Fully Buffered DDR2 SDRAM DIMMs
Basic Functionality
1. Advanced Memory Buffer Overview
The Advanced Memory Buffer reference design complies with the JEDEC FB-DIMM Architecture and Protocol
Specification.
2. Advanced Memory Buffer Functionality
2.1 Advanced Memory Buffer
•
•
•
•
•
•
•
•
•
•
Supports channel initialization procedures as defined in the initialization chapter of the FB-DIMM Architecture and Protocol Specification to align the clocks and the frame boundaries verify channel connectivity and identify AMB DIMM position.
Supports the forwarding of southbound and northbound frames, servicing requests directed to DIMM,
as defined in the protocol chapter, and merging the return data into the northbound frames.
If the AMB resides on the last DIMM in the channel, the AMB initializes northbound frames.
Detects errors on the channel and reports them to the host memory controller.
Acts as DRAM memory buffer for all read, write and configuration accesses addressed to the DIMM.
Provides a read buffer FIFO and a write buffer FIFO.
Supports an SMBus protocol interface for access to the AMB configuration registers.
Provides logic to support MEMBIST and IBIST Design for Test functions.
Provides a register interface for the thermal sensor and status indicator.
Functions as a repeater to extend the maximum length of FBD Links.
2.2 Transparent Mode for DRAM Test Support
In this mode, the Advanced Memory Buffer will provide lower speed tester access to DRAM pins through
the FB-DIMM I/O pins. This allows the tester to send and arbitrary test pattern to the DRAMs. Transparent
mode only supports a maximum DRAM frequency equivalent to DDR2 400.
Transparent mode functionality:
•
•
•
Reconfigure FB-DIMM inputs from differential high speed link receivers to two single ended lower
speed receivers(~200 Mhz)
These inputs directly control DDR2 Command/Address and input data that is replicated to all DRAMs
Used low speed direct drive FB-DIMM outputs to bypass high speed Parallel/Serial circuitry and provide
test results back to tester
2.3 DDR2 SDRAM
•
•
•
Supports DDR2 at speeds of 533,667 and 800 MT/s
Supports 512Mb devices in x4 and x8 configurations
72 bit DDR2 SDRAM memory array
Rev 1.2 / Feb. 2009
13
1240pin Fully Buffered DDR2 SDRAM DIMMs
3. Advanced Memory Buffer Block Diagram
10x2
10x2
South bound
Data in
South bound
Data out
Data Merge
Re-Time
PLL
Re-synch
1x2
Demux
Ref Clock
PISO
I0*12
I0*12
MUX
Reset#
Link init SM &
Control & CSRs
Reset
Control
Init
patterns
IBIST - RX
Command
Decoder &
CRC Check
IBIST - RX
Failover
DRAM Cmd
MUX
LAI Logic
Thermal
Sensor
DDR State
Controller
& CSRs
Core Control
& CSRs
MUX
36 Deep
Write
Data
FIFO
External MEMBIST
DDR Calibration &
DDR IOBIST/DFX
LAI
Controller
Data CRC Gen
& Read FIFO
Data
Out
DRAMclock
4
DRAMclock#
29
DRAM Address
/CommandCopy1
29
DRAM Address
/CommandCopy2
DDR
IO’s
72+18X2
DRAM Address
Data/Strobe
Data In
NB LAI
Buffer
Sync & Idle
Pattern Generator
IBIST - TX
Cmd
Out
4
IBISt - RX
MUX
SMbus
SMbus
Controller
Link init SM &
Control & CSRs
Failover
14*6*2
14*12
PISO
Demux
Re-synch
Data Merge
Northbound
DataOut
14x2
Re-Time
14x2
Northbound
DataIn
Advanced Memory Buffer Block Diagram
Rev 1.2 / Feb. 2009
14
1240pin Fully Buffered DDR2 SDRAM DIMMs
4. Interfaces
Below Figure illustrates the AMB and all of its interfaces.They consists of two FB-DIMM links, one DDR2 channel and
an SMBus interface. Each FB-DIMM link connects the AMB to a host memory controller or an adjacent FB-DIMM.
The DDR2 channel supports direct connection to the DDR2 SDRAMs on a Fully Buffered DIMM.
M e m o ry In te rfa ce
SB FBD
In L in k
SB FBD
O u t L in k
AMB
NB FBD
O u t L in k
NB FBD
In L in k
Secondary or to
optional next FBD
Primary or Host
Direction
DDR2
Channel
SMBus
A d v a n c e d M e m o ry B u ffe r In te rfa c e s
4.1 FBD High-Speed Differential Point-to-Point Link (at 1.5V) Interfaces
The Advanced Memory Buffer supports one FBD channel consisting of two bidirectional link interfaces
using high speed differential point-to-point electrical signaling.
The southbound input link is 10 lanes wid and carries commands and write data from the host memory
controller or the adjacent DIMM in the host direction. The southbound output link forwards this same data
to the next FBD.
The northbound input link is 13 to 14 lanes wide and carries read return data or status information from
the next FB-DIMM in the chain back towards the host. The northbound output link forwards this information back towards the host and multiplexes in any read return data or status information that is generated
internally.
4.2 DDR2 Channel
The DDR2 channel on the Advanced Memory Buffer supports direct connection to DDR2 SDRAMs. The
DDR2 channel supports two ranks of eight banks with 16 row/column request, 64 data signals, and eight
check-bit signals.
There are two copies of address and command signals to support DIMM routing and electrical requirements.
Four transfer bursts are driven on the data and check-bit lines at 800 MHz. Propagation delays between
read data/check-bit strobe lanes on a given channel can differ. Each strobe can be calibrated by hardware
state machines using write/read trial and error. Hardware aligns the read data and check-bits to a single
core clock. The Advanced Memory Buffer provides four copies of the command clock phase references(CLK[3:0]) and write data/check-bit strobes(DQSs) for each DRAM nibble.
Rev 1.2 / Feb. 2009
15
1240pin Fully Buffered DDR2 SDRAM DIMMs
4.3 SMBus Slave Interface
The Advanced Memory Buffer supports an SMBus interface to allow system access to configuration registers independent of the FB-DIMM link. The Advanced Memory Buffer will never be a master on the SMBus,
only a slave. Serial SMBus data transfer is supported at 100 kHz. SMBus access to the Advanced Memory
Buffer may be a requirement to boot and to set link strength, frequency and other parameters needed to
insure robust configurations. It is also required for diagnostic support when the link is down. The SMBus
address straps located on the DIMM connector are used by the unique ID.
4.4 FBD Channel Latency
FB-DIMM channel latency is measured from the time a read request is driven on the FB-DIMM channel pins
to the time when the first 16 bytes (2nd chunk) of read completion data is sampled by the memory controller. When not using the Variable Read Latency capability, the latency for a specific DIMM on a channel
is always equal to the latency for any other DIMM on that channel. However, the latency for each DIMM in
a specific configuration with some number of DIMMs installed. As more DIMMs are added to the channel,
additional latency is required to read from each DIMM on the channel. Because the channel is based on
the point to point interconnection of buffer components between DIMMs, memory requests are required to
travel through N-1 buffers before reaching the Nth buffer. The result is that a 4 DIMM channel configuration will have greater idle read latency compared to a 1DIMM channel configuration.The Variable Read
Latency capability can be used to reduce latency for DIMMs closer to the host. The idle latencies listed in
this section are representative of what might be achieved in typical AMB designs. Actual implementations
with latencies less than the values listed will have higher application performance and vice versa.
4.5 Peak Theoretical Throughput
An FB-DIMM channel transfers read completion data on the FBD Northbound data connection. 144 bits of data are
transferred for every FBD Northbound data frame. This matches the 18-byte data transfer of an ECC DDR DRAM in a
single DRAM command clock. A DRAM burst of 8 from a single channel or a DRAM burst of four from two lock stepped
channels provides a total of 72 bytes of data(64 bytes plus 8 bytes ECC)
The FBD frame rate matches the DRAM command clock because of the fixed 6:1 ratio of the FBD channel clock to the
DRAM command clock. Therefore, the Northbound data connection will exhibit the same peak theoretical throughput
as a single DRAM channel. For example, when using DDR2 533 DRAMs, the peak theoretical throughput as a single
DRAM channel.For example, when using DDR2 533 DRAMs, the peak theoretical bandwidth of the Northbound data
connection is 4.276 GB/sec.
Write data is transferred on the FBD Southbound command and data connection, via Command+Wdata frames. 72
bits of data are transferred for every FBD Command+Wdata frame. Two Command+Wdata frames match the 18-byte
data transfer of and ECC DDR DRAM in a single DRAM command clock. A DRAM burst of 8 transfers from a single
channel, or a burst of 4 from two lock-step channels provides a total of 72 bytes of data(64 bytes plus & bytes ECC)
When the FBD frame rate matches the DRAM command clock, the Southbound command and data connection will
exhibit one half the peak theoretical throughput of a single DRAM channel. For example, when using DDR2 533
DRAMs, the peak theoretical bandwidth of the Southbound command and data connection is 2.133 GB/sec.
The total peak theoretical throughput for a single FBD channel is defined as the sum of the peak theoretical throughput of the Northbound data connection and the Southbound command and data connection. When the FBD frame rate
matches the DRAM command clock, this is equal to 1.5 times the peak theoretical throughput of a single DRAM channel. For example, when using DDR2 533 DRAMs, the peak theoretical throughput of a DDR2 533 channel would be
4.267 GB/sec, while the peak theoretical throughput of and FBD -/+533 channel would be 6.4 GB/sec.
Rev 1.2 / Feb. 2009
16
1240pin Fully Buffered DDR2 SDRAM DIMMs
5 Hot-add
The FB-DIMM channel does not provide a mechanism to automatically detect and report the addition of a
new DIMM south of the currently active last DIMM. It is assumed the system will be notified through some
means of the addition of one or more new DIMMs so that specific commands can be sent to the host controller to initialize the newly added DIMM(s) and perform a Hot-add Reset to bring them into the channel
timing domain. It should be noted that the power to the DIMM socket must be removed before a “hot-add”
DIMM is inserted or removed. Applying or removing the power to a DIMM socket is a system platform
function.
6 Hot-remove
In order to accomplish removal of DIMMs the host must perform a Fast Reset sequence targeted at the last
DIMM that will be retained on the channel. The Fast Reset re-establish the appropriate last DIMM so that
the Southbound
Tx outputs of the last DIMM and the Southbound and Northbound outputs of the DIMMs beyond the last
active DIMM are disabled. Once the appropriate outputs are disabled the system can coordinate the procedure to remove power in preparation for physical removal of the DIMM if needed.
It should be noted that the power to the DIMM socket must be removed before a “hot-add” DIMM is
inserted or removed. Applying or removing the power to a DIMM socket is a system platform function.
7 Hot-replace
Hot replace of DIMM is accomplished through combing th Hot-Remove and Hot-Add process.
Rev 1.2 / Feb. 2009
17
1240pin Fully Buffered DDR2 SDRAM DIMMs
Electrical Characteristics
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Value
Unit
Note
VIN, VOUT
- 0.3 V ~ 1.75 V
V
1
Voltage on VCC relative to Vss
VCC
- 0.3 V ~ 1.75 V
V
1
Voltage on VDD relative to Vss
VDD
- 0.5 V ~ 2.3 V
V
1
Voltage on VTT relative to Vss
VTT
- 0.5 V ~ 2.3 V
V
1
TSTG
- 55 oC ~ 100 oC
Voltage on any pins relative to Vss
Storage Temperature range
o
1
C
Note:
1. Stress greater than those listed may cause permanent damage to the device. This is a stress rating only, and device
functional operation at or above the conditions indicated is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
OPERATING TEMPERATURE RANGE
Parameter
AMB Component Case temperature Range
DRAM Component Case Temperature Range
Symbol
TCASE
Rating
0 ~ + 110
Units
oC
Notes
TCASE
0 ~ + 95
oC
1,2
Note:
1. Within the DRAM component Case Temperature range all DRAM specification will be supported.
2. If the DRAM case temperature is Above 85oC, the Auto-Refresh command interval has to be reduced from 7.8us of
tREFI to 3.9us.
Supply Voltage Levels and DC Operating Conditions.
Parameter
Symbol
Min
Nom
Max
Unit
AMB Supply Voltage
VCC
1.455
1.5
1.575
V
DRAM Supply Voltage
VDD
1.7
1.8
1.9
V
Termination Voltage
EEPROM Supply Voltage
VTT
0.50 x VDD
3.3
0.52 x VDD
3.6
V
VDDSPD
0.48 x VDD
3.0
V
Note
DC Input Logic High(SPD)
VIH(DC)
2.1
-
VDDSPD
V
1
DC Input Logic Low(SPD)
VIL(DC)
-
-
0.8
V
1
DC Input Logic High(RESET)
VIH(DC)
1.0
-
-
V
2
DC Input Logic Low(RESET)
VIL(DC)
-
-
+0.5
V
2
IL
IL
-90
-5
-
+90
+5
uA
uA
2
3
Leakage Current (RESET)
Leakage Current (Link)
Note:
1. Applies for SMB and SPD bus Signals.
2. Applies for AMB CMOS Signal RESET.
3. for all other AMB related DC parameters, please refer to the High Speed Differential Link Interface Specifications
Rev 1.2 / Feb. 2009
18
1240pin Fully Buffered DDR2 SDRAM DIMMs
Timing Parameters
Parameter
Symbol
EI Assertion Pass-Thru Timing
Min
tEI Propagad
EI Deassertion Pass-Thru Timing
Typ
Max
Unit
Note
-
4
clks
-
bit lock
clks
-
clks
1
tEID
EI Assertion Duration
tEI
Bit Lock Interval
Frame Lock Interval
100
tBitLock
119
frames
1
tFrameLock
154
frames
1
Note:
1. Defined in FB-DIMM Architecture and Protocol Spec.
Environmental Parameters
Symbol
Parameter
Rating
Units
Notes
TOPR
Operating temperature
See Note
HOPR
Operating humidity(relative)
10 to 90
%
2
TSTG
Storage temperature
-50 to +100
oC
2
HSTG
Storage humidity(without condensation)
5 to 95
%
2
PBAR
Barometric pressure(operating)
3050
m
2
PBAR
Barometric pressure (storage)
15240
m
2
1
Note:
1. The designer must meet the case temperature specifications for individual module components.
2. Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and
device functional operation at or above the conditions indicated is not implied. Exposure to absolute maximum rating
conditions for extended periods
Rev 1.2 / Feb. 2009
19
1240pin Fully Buffered DDR2 SDRAM DIMMs
IDD Specification and Conditions
IDD Measurement Conditions
Symbol
Conditions
Idle_0
Idle Current, single or last DIMML0 state, idle (0 BW)Primary channel enabled, Secondary Channel Disabled CKE high. Command and address lines stable. DRAM clock
active.
Idle_1
Idle Current, first DIMML0 state, idle (0 BW)Primary and Secondary channels
enabled CKE high. Command and address lines stable. DRAM clock active.
Idle_2
Idle Current, DRAM power downL0 state, idle (0 BW)Primary and Secondary channels enabledCKE low. Command and address lines floated. DRAM clock active, ODT
and CKE driven low.
Active_1
Active PowerL0 state. 50% DRAM BW, 67% read, 33% write.
Primary and Secondary channels enabled. DRAM clock active, CKE high.
Active_2
Active Power, data pass throughL0 state. 50% DRAM BW to downstream DIMM,
67% read, 33% write. Primary and Secondary channels enabled CKE high.
Command and address lines stable. DRAM clock active.
L0s
Channel Standby Average power over 42 frames where the channel enters and exits
L0sDRAMs Idle (0 BW). CKE low. Command and address lines floated.
Dram clocks active, ODE and CKE driven low.
Training
(for AMB spec, not in
SPD)
Training Primary and Secondary channels enabled.100% toggle on all channels
lanes.DRAMs idle (0 BW).CKE high. Command and address lines stable.DRAM clock
active.
Rev 1.2 / Feb. 2009
20
1240pin Fully Buffered DDR2 SDRAM DIMMs
IDD Power Supply Currents Specifications.
SAC Timing Parameters by Speed Grade
512MB(HMP564F7FFP8C)
Power Supply
Intel
IDT
Y5
Icc_Idle_0 @1.5V
2400
IDT
1GB(HMP512F7FFP8C)
Intel
S5
2400
3000
IDT
Y5
2400
IDT
2GB(HMP525F7FFP4C)
Intel
S5
2400
3000
IDT
Unit
2400
mA
Note1)
Y5
2400
Idd_Idle_0 @1.8V
315
315
315
630
630
630
1260
1260
mA
Idle_0 Total Power
4.167
4.167
5.067
4.734
4.734
5.634
5.868
5.868
W
Icc_Idle_1 @1.5V
3100
3100
3875
3100
3100
3875
3100
3100
mA
Idd_Idle_1 @1.8V
315
315
315
630
630
630
1260
1260
mA
Idle_1 Total Power
5.217
5.217
6.380
5.784
5.784
6.947
6.918
6.918
W
Icc_Active_1 @1.5V
3600
3600
4500
3600
3600
4500
3600
3600
mA
Idd_Active_1 @1.8V
900
900
1035
1800
1800
2070
3600
3600
mA
Active_1 Total Power
7.020
7.020
8.613
8.640
8.640
10.476
11.880
11.880
W
Icc_Active_2 @1.5V
3300
3300
4125
3300
3300
4125
3300
3300
mA
Idd_Active_2 @1.8V
900
900
1035
1800
1800
2070
3600
3600
mA
Active_2 Total Power
6.570
6.570
8.051
8.190
8.190
9.914
11.430
11.430
W
Icc_Training @1.5V
4000
4000
5000
4000
4000
5000
4000
4000
mA
Idd_Training @1.8V
900
900
1035
1800
1800
2070
3600
3600
mA
Training Total Power
7.620
7.620
9.363
9.240
9.240
11.226
11.480
11.480
W
Note:
1) Assure that Primary channel Drive strength at 100% with De-emphasis at -6.5dB Secondary channel drive strength
at 60% with De-emphasis at -3dB when enabled. Address and Data fields are pseudo-random, which provides a 50%
toggle rate on DRAM data lines and link lanes when data is being transferred.
Assuming 1 activate command and 1 read/write command per BL=4 transferBL=4.10 lanes southbound and 14 lanes
northbound are enabled and active (12 lanes NB if non-ECC DIMM).
SPD specific assumption:Number of devices on the specific DIMM assumed.Termination of command, address, and
control is actual value used on the DIMM. ECC or non-ECC as per the specific DIMM.
SPD specifies Delta TAMB power spec specific assumptions: Dual rank x8 ECC DIMM assumed (18 DRAM devices
present on DIMM)
Modeled with 27 ohm termination for command, address, and clocks, and 47 ohm termination for control.
ECC DIMM assumed (72 bit data, 14 lanes northbound). AMB specification specifies current for each rail.
Rev 1.2 / Feb. 2009
21
1240pin Fully Buffered DDR2 SDRAM DIMMs
Termination Current
Internal signals are terminated on the DIMM through resistors to an external power supply VTT = VDD / 2.
Modeled with 30 Ohm termination for clocks, 39 ohm for command / address and 47 ohm for control.
The VTT power supply must be able to source and sink these currents:
VTT Currents table
Description
Symbol
Typ
Max
Unit
Idle Current, DRAM Power Down (Conditions TBD)
ITT1
-
700
mA
Active Power, 50% DRAM BW (conditions TBD)
ITT2
-
700
mA
Rev 1.2 / Feb. 2009
22
1240pin Fully Buffered DDR2 SDRAM DIMMs
PACKAGE OUTLINE
64Mx72, 512MB Module (1 rank of x8 based DDR2 SDRAMs)
HMP564F7FFP8C
FRONT VIEW
4.0 ±0.1
133.35 ±0.15
30.35
AMB
67.00
51.00
5.00
BACK VIEW
Chekbit
FRONT VIEW WITH HEAT SPREADER
Side
8.20 max
5.20 max
BACK VIEW WITH HEAT SPREADER
3.0 max
1.27±0.10
Note 1: All dimensions are typical millimeter scale unless otherwise stated.
Rev 1.2 / Feb. 2009
23
1240pin Fully Buffered DDR2 SDRAM DIMMs
PACKAGE OUTLINE
128Mx72, 1GB Module (2 ranks of x8 based DDR2 SDRAMs)
HMP512F7FFP8C
FRONT VIEW
30.35
4.0 ±0.1
133.35 ±0.15
AMB
67.00
51.00
5.00
BACK VIEW
Chekbit
Chekbit
FRONT VIEW WITH HEAT SPREADER
Side
8.20 max
5.20 max
BACK VIEW WITH HEAT SPREADER
3.0 max
1.27±0.10
Note 1: All dimensions are typical millimeter scale unless otherwise stated.
Rev 1.2 / Feb. 2009
24
1240pin Fully Buffered DDR2 SDRAM DIMMs
PACKAGE OUTLINE
256Mx72, 2GB Module (2 ranks of x4 based DDR2 SDRAMs)
HMP525F7FFP4C
FRONT VIEW
30.35
4.0 ±0.1
133.35 ±0.15
67.00
51.00
5.00
BACK VIEW
FRONT VIEW WITH HEAT SPREADER
Side
8.20 max
5.20 max
BACK VIEW WITH HEAT SPREADER
3.0 max
1.27±0.10
Note 1: All dimensions are typical millimeter scale unless otherwise stated.
Rev 1.2 / Feb. 2009
25
1240pin Fully Buffered DDR2 SDRAM DIMMs
REVISION HISTORY
Revision
History
Date
1.0
First Version Release
July. 2008
1.1
Orddering Info. table revised
Sep. 2008
1.2
IDD Power spec added
Feb. 2009
Rev 1.2 / Feb. 2009
Remark
26
Similar pages