Chenmko HPL46CTPT High efficiency silicon rectifier Datasheet

HPL41CTPT
CHENMKO ENTERPRISE CO.,LTD
THRU
SURFACE MOUNT GLASS PASSIVATED
HIGH EFFICIENCY SILICON RECTIFIER
VOLTAGE RANGE 50 - 1000 Volts CURRENT 4.0 Amperes
HPL48CTPT
PROVISIONAL SPEC.
FEATURE
*Sm al l S u r f ac e M o u n t i n g T y p e. (SMP)
* Low forward voltage, high current capability
* Low leakage current
* Glass passivated junction
* High temperature soldering guaranteed :
260oC/10 seconds at terminals
SMP
0.081 (2.05)
0.077 (1.95)
0.170 (4.31)
0.163 (4.15)
(3)
(1)
(2)
0.019 (0.50 Min.)
0.077 (1.95)
0.073 (1.85)
0.045 (1.16)
0.042 (1.07)
0.005 (0.15 Min.)
0.019 (0.50 Min.)
0.264 (6.70)
0.254 (6.46)
(2)
CIRCUIT
0.212 (5.38)
0.208 (5.29)
(1)
0.055 (1.40)
0.051 (1.30)
(3)
SMP
Dimensions in inches and (millimeters)
MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted )
RATINGS
SYMBOL
HPL41CTPT HPL42CTPT HPL43CTPT HPL44CTPT HPL45CTPT HPL46CTPT HPL47CTPT HPL48CTPT
UNITS
Maximum Recurrent Peak Reverse Voltage
VRRM
50
100
200
300
400
600
800
1000
Volts
Maximum RMS Voltage
VRMS
35
70
140
210
280
420
560
700
Volts
Maximum DC Blocking Voltage
VDC
50
100
200
300
400
600
800
1000
Volts
o
Maximum Average Forward Rectified Current TL = 100 C
IO
4.0
Amps
IFSM
60
Amps
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
Typical Junction Capacitance (Note 1)
Operating and Storage Temperature Range
CJ
30
TJ, TSTG
20
pF
o
-65 to +150
C
ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted )
CHARACTERISTICS
SYMBOL
Maximum Instantaneous Forward Voltage at 2.0 A DC
Maximum DC Reverse Current
at Rated DC Blocking Voltage at TA = 25oC
Maximum Full Load Reverse Current Average,
Full Cycle at TA = 55oC
Maximum Reverse Recovery Time (Note 2)
NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts
2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A
VF
HPL41CTPT HPL42CTPT HPL43CTPT HPL44CTPT HPL45CTPT HPL46CTPT HPL47CTPT HPL48CTPT
1.0
1.3
1.5
1.7
UNITS
Volts
5.0
uAmps
100
uAmps
IR
trr
50
70
nSec
2004-7
RATING CHARACTERISTIC CURVES ( HPL41CTPT THRU HPL48CTPT )
10
NONINDUCTIVE
trr
+0.5A
(-)
D.U.T
(+)
0
PULSE
GENERATOR
(NOTE 2)
25 Vdc
(approx)
(-)
1
NONINDUCTIVE
OSCILLOSCOPE
(NOTE 1)
-0.25A
(+)
-1.0A
1cm
NOTES: 1. Rise Time = 7 ns max. Input Impedance =
1 megohm. 22 pF.
2. Rise Time = 10 ns max. Source Impedlance=
50 ohms.
SET TIME BASE FOR
10/20 nS/cm
FIG. 3 - TYPICAL REVERSE CHARACTERISTICS
2.0
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0
0
25 50 75 100 125 150 175
LEAD TEMPERATURE ( OC )
TJ =100oC
1.0
TJ =25oC
.1
TP
TP
HP
6C
L4
TP
8C
T
5C
T~
L4
HP
TP
HP
L4
L44
7C
~H
PT
CT
HP
PL4
~H
PT
CT
L41
T
TP
T
3C
PL4
Pulse Width = 300uS
1% Duty Cycle
1.0
HP
TJ =125oC
10
T
10
INSTANTANEOUS FORWARD CURRENT, ( A )
INSTANTANEOUS REVERSE CURRENT, (uA)
4.0
FIG. 4 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
100
0.1
TJ =25oC
.01
.001
.01
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % )
0
.2
.4
.6
.8
1.0
1.2 1.4
1.6
INSTANTANEOUS FORWARD VOLTAGE, ( V )
1.8
FIG. 6 - TYPICAL JUNCTION CAPACITANCE
FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT
200
70
60
JUNCTION CAPACITANCE, ( pF )
PEAK FORWARD SURGE CURRENT, ( A )
FIG. 2 - TYPICAL FORWARD
CURRENT DERATING CURVE
AVERAGE FORWARD CURRENT, ( A )
FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC
50
NONINDUCTIVE
8.3ms Single Half Sine-Wave
(JEDEC Method)
50
40
30
20
10
0
100
60
HPL4
1
40
20
HPL4
CTPT
~
6CTP
10
HPL4
5
T~HP
CTPT
L48C
TPT
6
4
TJ =25oC
2
1
1
2
5
10
20
NUMBER OF CYCLES AT 60 Hz
50
100
.1
.2
.4
1.0
2
4
10
20
REVERSE VOLTAGE, ( V )
40
100
Similar pages