NEC HR1XXX On-chip resistor pnp silicon epitaxial transistor for mid-speed switching Datasheet

DATA SHEET
COMPOUND TRANSISTOR
HR1 SERIES
on-chip resistor PNP silicon epitaxial transistor
For mid-speed switching
FEATURES
PACKAGE DRAWING (UNIT: mm)
• Up to 2A high current drives such as IC outputs and actuators
available
• On-chip bias resistor
• Low power consumption during drive
HR1 SERIES LISTS
Products
Marking
R1 (KΩ)
R2 (KΩ)
HR1A3M
MP
1.0
1.0
HR1F3P
MQ
2.2
10
HR1L3N
MR
4.7
10
HR1A4,
MS
10
10
HR1L2Q
MT
0.47
4.7
HR1F2Q
MU
0.22
2.2
HR1A4A
MX
−
10
ABSOLUTE MAXIMUM RATINGS (Ta = 25°°C)
Parameter
Symbol
Ratings
Unit
Collector to base voltage
VCBO
−60
V
Collector to emitter voltage
VCEO
−60
V
Emitter to base voltage
VEBO
−10
V
Collector current (DC)
IC(DC)
−1.0
A
IC(pulse) *
−2.0
A
Base current (DC)
IB(DC)
−0.02
A
Total power dissipation
Collector current (Pulse)
PT **
2.0
W
Junction temperature
Tj
150
°C
Storage temperature
Tstg
−55 to +150
°C
* PW ≤ 10 ms, duty cycle ≤ 50 %
** When 0.7 mm × 16 cm ceramic board is used
2
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for
availability and additional information.
Document No. D16184EJ2V0DS00 (2nd edition)
Date Published April 2002 N CP(K)
Printed in Japan
©
2002
1998
HR1 SERIES
+5$0
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
MIN.
TYP.
VCB = −60 V, IE = 0
MAX.
Unit
−100
nA
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
50
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
DC current gain
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
Low level output voltage
VOL **
VIN = −5.0 V, IC = −0.4 A
−0.4
Low level input voltage
VIL **
VCE = −5.0 V, IC = −100 µA
−0.3
V
−
V
Input resistance
R1
0.7
1.0
1.3
kΩ
E-to-B resistance
R2
0.7
1.0
1.3
kΩ
MIN.
TYP.
MAX.
Unit
−100
nA
3:≤µVGXW\F\FOH≤
+5)3
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
VCB = −60 V, IE = 0
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
150
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
DC current gain
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
−
Low level output voltage
VOL **
VIN = −5.0 V, IC = −0.3 A
−0.3
VIL **
VCE = –5.0 V, IC = −100 µA
−0.3
V
Low level input voltage
V
Input resistance
R1
1.54
2.2
2.86
kΩ
E-to-B resistance
R2
7
10
13
kΩ
MIN.
TYP.
MAX.
Unit
−100
nA
3:≤µVGXW\F\FOH≤
+5/1
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
VCB = −60 V, IE = 0
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
150
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
DC current gain
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
Low level output voltage
VOL **
VIN = −5.0 V, IC = −0.2 A
−0.3
V
Low level input voltage
VIL **
VCE = −5.0 V, IC = −100 µA
−0.3
V
Input resistance
R1
3.29
4.7
6.11
kΩ
E-to-B resistance
R2
7
10
13
kΩ
3:≤µVGXW\F\FOH≤
−
'DWD6KHHW'(-9'6
HR1 SERIES
+5$0
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
MIN.
TYP.
VCB = −60 V, IE = 0
MAX.
Unit
−100
nA
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
150
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
DC current gain
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
Low level output voltage
VOL **
VIN = −5.0 V, IC = −0.1 A
−0.2
Low level input voltage
VIL **
VCE = −5.0 V, IC = −100 µA
−0.3
V
−
V
Input resistance
R1
7
10
13
kΩ
E-to-B resistance
R2
7
10
13
kΩ
MIN.
TYP.
MAX.
Unit
−100
nA
3:≤µVGXW\F\FOH≤
+5/4
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
VCB = −60 V, IE = 0
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
150
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
DC current gain
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
−
Low level output voltage
VOL **
VIN = −5.0 V, IC = −0.5 A
−0.55
VIL **
VCE = −5.0 V, IC = −100 µA
−0.3
V
Low level input voltage
V
Input resistance
R1
329
470
611
Ω
E-to-B resistance
R2
3.29
4.7
6.11
kΩ
MIN.
TYP.
MAX.
Unit
−100
nA
3:≤µVGXW\F\FOH≤
+5)4
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
VCB = −60 V, IE = 0
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
100
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
DC current gain
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
Low level output voltage
VOL **
VIN = −5.0 V, IC = −0.5 A
−0.55
V
Low level input voltage
VIL **
VCE = −5.0 V, IC = −100 µA
−0.3
V
−
Input resistance
R1
154
220
286
kΩ
E-to-B resistance
R2
1.54
2.2
2.86
kΩ
3:≤µVGXW\F\FOH≤
'DWD6KHHW'(-9'6
HR1 SERIES
+5$$
(/(&75,&$/&+$5$&7(5,67,&6 7D °°&
Parameter
Collector cutoff current
Symbol
ICBO
Conditions
TYP.
VCB = −60 V, IE = 0
MAX.
Unit
−100
nA
DC current gain
hFE1 **
VCE = −2.0 V, IC = −0.1 A
150
−
DC current gain
hFE2 **
VCE = −2.0 V, IC = −0.5 A
100
−
hFE3 **
VCE = −2.0 V, IC = −1.0 A
50
DC current gain
Collector saturation voltage
Low level input voltage
VCE(sat) **
IC = −500 mA, IB = −10 mA
VIL **
VCE = −5.0 V, IC = −100 µA
−0.3
Input resistance
R1
E-to-B resistance
R2
7
'DWD6KHHW'(-9'6
−
0.20
−
3:≤µVGXW\F\FOH≤
MIN.
0.35
V
−1.5
V
−
−
Ω
10
13
kΩ
HR1 SERIES
7<3,&$/&+$5$&7(5,67,&6 7a °°&
'DWD6KHHW'(-9'6
HR1 SERIES
• The information in this document is current as of July, 2001. The information is subject to change
without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data
books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products
and/or types are available in every country. Please check with an NEC sales representative for
availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without prior
written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document.
• NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of
third parties by or arising from the use of NEC semiconductor products listed in this document or any other
liability arising from the use of such products. No license, express, implied or otherwise, is granted under any
patents, copyrights or other intellectual property rights of NEC or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of customer's equipment shall be done under the full
responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third
parties arising from the use of these circuits, software and information.
• While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers
agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize
risks of damage to property or injury (including death) to persons arising from defects in NEC
semiconductor products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment, and anti-failure features.
• NEC semiconductor products are classified into the following three quality grades:
"Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products
developed based on a customer-designated "quality assurance program" for a specific application. The
recommended applications of a semiconductor product depend on its quality grade, as indicated below.
Customers must check the quality grade of each semiconductor product before using it in a particular
application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's
data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not
intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness
to support a given application.
(Note)
(1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries.
(2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for
NEC (as defined above).
M8E 00. 4
Similar pages