Intersil HS0-1825ARH-Q Radiation hardened high-speed, dual output pwm Datasheet

HS-1825ARH
®
Data Sheet
September 25, 2008
Radiation Hardened High-Speed, Dual
Output PWM
The Radiation Hardened HS-1825ARH Pulse Width
Modulator is designed to be used in high frequency
switched-mode power supplies and can be used in either
current-mode or voltage-mode. It is well suited for
single-ended boost converter applications.
Device features include a precision voltage reference, low
power start-up circuit, high frequency oscillator, wide-band
error amplifier, and fast current-limit comparator. The use of
proprietary process capabilities and unique design
techniques results in fast propagation delay times and high
output current over a wide range of output voltages.
FN4561.8
Features
• Electrically Screened to DESC SMD # 5962-99558
• QML Qualified per MIL-PRF-38535 Requirements
• Radiation Environment
- Maximum Total Dose . . . . . . . . . . . . . . . . 300 krad(SI)
- Vertical Architecture Provides Low Dose Rate Immunity
- DI RSG Process Provides Latch-Up Immunity
• Low Start-Up Current . . . . . . . . . . . . . . . . . . . 100µA (Typ)
• Fast Propagation Delay . . . . . . . . . . . . . . . . . . 80ns (Typ)
• 12V to 30V Operation
• 1A (Peak) Dual Output Drive Capability
Constructed with the Intersil Rad Hard Silicon Gate (RSG)
Dielectric Isolation BiCMOS process, the HS-1825ARH has
been specifically designed to provide highly reliable
performance when exposed to harsh radiation
environments.
• 5.1V Reference
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed below must be used when ordering.
• Latched Overcurrent Comparator with Full Cycle Restart
Detailed Electrical Specifications for the HS-1825ARH
are contained in SMD 5962-99558. That document may
be easily downloaded from our website.
www.intersil.com/
Applications
• Undervoltage Lockout
• Programmable Soft-Start
• Switching Frequencies to 500kHz
• Programmable Leading Edge Blanking Circuit
• Current or Voltage Mode Switching Power Supplies
• Motor Speed and Direction Control
Pinout
HS-1825ARH
SBDIP (CDIP2-T16) AND FLATPACK (CDFP4-F16)
TOP VIEW
INV 1
16 VREF 5.1V
NON-INV 2
15 VCC
E/A OUT 3
14 OUTPUT B
CLOCK 4
13 VC
RT 5
12 POWER GND
CT 6
11 OUTPUT A
RAMP 7
SOFT START 8
10 GND
9 ILIM/SD
NOTE: Grounding the Soft-Start pin does not inhibit the outputs. The
outputs may be inhibited by applying >1.26V to the ILIM/SD pin.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002, 2005, 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
HS-1825ARH
Ordering Information
INTERNAL
MKT. NUMBER
ORDERING NUMBER
TEMP. RANGE (°C)
PKG.
DWG. #
PACKAGE
5962F9955801V9A
HS0-1825ARH-Q
-50 to +125
HS0-1825ARH/Sample
HS0-1825ARH/Sample
-50 to +125
5962F9955801VEC
HS1-1825ARH-Q
-50 to +125
16 Ld SBDIP
D16.3
5962F9955801QEC
HS1-1825ARH-8
-50 to +125
16 Ld SBDIP
D16.3
5962F9955801VXC
HS9-1825ARH-Q
-50 to +125
16 Ld Flatpack
K16.A
5962F9955801QXC
HS9-1825ARH-8
-50 to +125
16 Ld Flatpack
K16.A
HS1-1825ARH/Proto
HS1-1825ARH/Proto
-50 to +125
16 Ld SBDIP
D16.3
HS9-1825ARH/Proto
HS9-1825ARH/Proto
-50 to +125
16 Ld Flatpack
K16.A
Typical Performance Curves
100
10k
C220pF
DMAX
90
C1000pF
1k
DMAX (%)
FREQUENCY (kHz)
C470pF
C2200pF
C4700pF
100
80
70
60
C22nF
10
C10nF
1
10
Rt TIMING RESISTANCE (kΩ)
100
FIGURE 1. OSCILLATOR FREQUENCY vs Rt AND Ct
2
50
1
10
Rt TIMING RESISTANCE (kΩ)
100
FIGURE 2. MAXIMUM DUTY CYCLE vs Rt
FN4561.8
September 25, 2008
HS-1825ARH
Die Characteristics
DIE DIMENSIONS
4710µm x 3570µm (185 mils x 140 mils)
Thickness: 483µm ±25.4µm (19 mils ±1 mil)
Backside Finish
Silicon
ASSEMBLY RELATED INFORMATION
INTERFACE MATERIALS
Substrate Potential
Glassivation
Type: PSG (Phosphorous Silicon Glass)
Thickness: 8.0kÅ ±1.0kÅ
Unbiased (DI)
ADDITIONAL INFORMATION
Top Metallization
Type: ALSiCu
Thickness: 16.0kÅ ±2kÅ
Worst Case Current Density
<2.0 x 105 A/cm2
Substrate
Radiation Hardened Silicon Gate,
Dielectric Isolation
Metallization Mask Layout
Transistor Count
225
HS-1825ARH
(4) CLK/LEB
RT (5)
(3) EAOUT
CT (6)
(2) IN+
RAMP (7)
(1) INSS (8)
(16) VREF
ILIM (9)
OSCGND
(NOTE 1)
(15) VCC
GND (10)
(14) OUTB
OUTA (11)
(12) PGND
(NOTE 2)
PGND (12)
(NOTE 2)
(13) VC
(NOTE 2)
VC (13)
(NOTE 2)
NOTES:
1. This is the oscillator ground (OSCGND) bond pad and must be
connected to GND.
2. PGND and VC each require two bond pad connections.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
3
FN4561.8
September 25, 2008
Similar pages