Intersil HS1B-0509RH-Q Radiation hardened single 8/differential 4-channel cmos analog multiplexer Datasheet

HS-0508RH, HS-0509RH
Data Sheet
Radiation Hardened Single 8/Differential
4-Channel CMOS Analog Multiplexers
These radiation hardened monolithic CMOS multiplexers
each include an array of eight analog switches, a digital
decode circuit for channel selection, a voltage reference for
logic thresholds, and an ENABLE input for device selection
when several multiplexers are present.
The Dielectric Isolation (DI) process used in fabrication of
these devices eliminates the problem of latch-up. Also, DI
offers much lower substrate leakage and parasitic
capacitance than conventional junction-isolated CMOS.
Switches are guaranteed to break-before-make, so that two
channels are never shorted together. The switching
threshold for each digital input is established by an internal
+5V reference, providing a guaranteed minimum 2.4V for
logic “1” and maximum 0.8 for logic “0”. This allows direct
interface without pull-up resistors to signals from most logic
families: CMOS, TTL, DTL and some PMOS. For protection
against transient overvoltage, the digital inputs include a
series 200Ω resistor and a diode clamp to each supply. The
HS-0508RH is an eight channel single-ended multiplexer,
and the HS-0509RH is a four channel differential version. If
input overvoltage protection is needed, the HS-0548RH and
HS-0549RH multiplexers are recommended.
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-95692. A “hot-link” is provided
on our homepage for downloading.
http://www.intersil.com/spacedefense/space.htm
August 1999
File Number
3977.2
Features
• Electrically Screened to SMD # 5962-95692
• QML Qualified per MIL-PRF-38535 Requirements
• Gamma Dose . . . . . . . . . . . . . . . . . . . . . . 1 x 104RAD(Si)
• No Latch-Up
• No Channel Interaction During Overvoltage
• Low On Resistance . . . . . . . . . . . . . . . . . . . . <200Ω (Typ)
• 44V Maximum Power Supply
• Break-Before-Make Switch
• Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . ±15V
• Access Time. . . . . . . . . . . . . . . . . . . . . . . . . <300ns (Typ)
Applications
• Data Acquisition Systems
• Control Systems
• Telemetry
Ordering Information
ORDERING NUMBER
INTERNAL
MKT. NUMBER
TEMP. RANGE
(oC)
5962D9569201VEA
HS1-0508RH-Q
-55 to 125
5962D9569201VEC
HS1B-0508RH-Q
-55 to 125
5962D9569202VEA
HS1-0509RH-Q
-55 to 125
5962D9569202VEC
HS1B-0509RH-Q
-55 to 125
Pinouts
HS-0508RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
A0 1
16 A1
ENABLE 2
15 A2
HS-0509RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
A0 1
ENABLE 2
14 GND
-VSUPPLY 3
-VSUPPLY 3
16 A1
15 GND
14 +VSUPPLY
IN 1 4
13 +VSUPPLY
IN 1A 4
13 IN 1B
IN 2 5
12 IN 5
IN 2A 5
12 IN 2B
IN 3 6
11 IN 6
IN 3A 6
11 IN 3B
IN 4 7
10 IN 7
IN 4A 7
10 IN 4B
OUT 8
9 IN 8
OUTA 8
1
9 OUT B
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
HS-0508RH, HS-0509RH
Functional Diagrams
HS-0508RH
HS-0509RH
OUT
IN1
IN2
OUT A
IN1A
IN4A
DECODER/
DRIVER
IN1B
IN8
OUT B
DECODER/
DRIVER
IN4B
LEVEL
SHIFT
5V
REF
†
†DIGITAL INPUT
PROTECTION
†
LEVEL
SHIFT
5V
REF
†
†
†DIGITAL INPUT
PROTECTION
†
†
A0 A1
A0 A1 A2 EN
HS-0508RH TRUTH TABLE
†
EN
HS-0509RH TRUTH TABLE
A2
A1
A0
EN
“ON” CHANNEL
A1
A0
EN
“ON” CHANNEL PAIR
X
X
X
L
NONE
X
X
L
NONE
L
L
L
H
1
L
L
H
1
L
L
H
H
2
L
H
H
2
L
H
L
H
3
H
L
H
3
L
H
H
H
4
H
H
H
4
H
L
L
H
5
H
L
H
H
6
H
H
L
H
7
H
H
H
H
8
2
HS-0508RH, HS-0509RH
Schematic Diagrams
TTL REFERENCE CIRCUIT
V+
R10
R9
Q1
Q4
D3
LEVEL SHIFTER
V+
P
P
P
P
OVERVOLTAGE
PROTECTION
R3
V+
D2
R1
ADD
IN.
N
P
P
P
LEVEL
SHIFTED
ADDRESS
TO
DECODE
R2
N
P
P
P
R5
R7
R6
R8
LEVEL
SHIFTED
ADDRESS
TO
DECODE
R4
N
N
N
N
N
N
N
N
200Ω
D1
V-
V-
FIGURE 1. ADDRESS INPUT BUFFER AND LEVEL SHIFTER
P
P
P
N
A0 OR A0
P
N
N
P
N
N18
FROM DECODE
V+
N17
N19
IN
A1 OR A1
TO N-CHANNED DEVICE
OF THE SWITCH
P
P
TO P-CHANNED DEVICE
OF THE SWITCH
+V
N
A2 OR A2
N
A3 OR A3
N
ENABLE
DELETE A3 OR A3 INPUT FOR HI-507
DELETE A3 OR A3 INPUT FOR HI-508
DELETE A2 OR A2 INPUT FOR HI-509
V-
FIGURE 2. ADDRESS DECODER
3
OUT
P17
V-
P18
FROM DECODE
FIGURE 3. MULTIPLEX SWITCH
HS-0508RH, HS-0509RH
Burn-In/Life Test Circuits
V1
F0
1
16
F1
1
16
F3
2
15
F2
2
15
3
14
3
14
4
13
4
13
5
12
6
11
7
10
8
9
V1
D1
V2
V2
C1
D1
5
12
6
11
7
10
8
9
D2
R1
C2
D2
R1
HS-0508RH
DYNAMIC BURN-IN AND LIFE TEST CIRCUIT
V1 =
V2 =
R1 =
C1 =
D1 =
F0 =
F1 =
F2 =
F3 =
1
16
F2
2
15
3
14
4
13
5
12
6
7
8
9
V3
D1
C1
R1
V1 =
V2 =
V3 =
R1 =
C1 =
D1 =
1
16
2
15
3
14
4
13
5
12
11
6
11
10
7
10
8
9
V2
C1
V3
D1
R1
+15.5V, ±.0.5V
-15.5V, ±0.5V
10kΩ, ±5%
0.1µF minimum (per socket)
1N4002 or equivalent (per board)
100kHz, ±10%; F1 = F0/2; F2 = F1/2, 50% duty cycle,
VIL = 0.8V max.; VIH = 4.0V min.
4
C1
V2
R1
HS-0509RH
STATIC BURN-IN TEST CIRCUIT
V1 =
V2 =
V3 =
R1 =
C1 =
D1 =
V1
D1
R1
HS-0509RH
DYNAMIC BURN-IN AND LIFE TEST CIRCUIT
V2 =
V3 =
R1 =
C1 =
D1 =
F0 =
5V minimum, 6V maximum
-15V maximum, -16V minimum
+15V minimum, +16V maximum
10kΩ ±5% 1/4W
C2 = 0.01µF minimum (per socket) or 0.1µF minimum (per row)
D2 = 1N4002 (or equivalent)
F1
D1
C2
HS-0508RH
STATIC BURN-IN TEST CIRCUIT
-15V maximum, -16V minimum
+15V minimum, +16V maximum
10kΩ ±5% 1/4W
C2 = 0.01µF minimum (per socket) or 0.1µF minimum (per row)
D2 = 1N4002 (or equivalent)
100kHz 50% duty cycle; VIL = 0.8V max; VIH = 4.0V min.
F0/2
F1/2
F2/2
F0
V3
C1
+5.5V, ±0.5V
+15.5V, ±0.5V
-15.5V, ±0.5V
10kΩ, ±10%
0.1µF minimum (per socket)
1N4002 or equivalent (per board)
C1
HS-0508RH, HS-0509RH
Irradiation Circuits
HS-0509RH
+5V
-15V
+1V
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
R1
+15V
+1V
R2
R1 = R2 = 10kΩ ±5%
HS-0508RH
+5V
-15V
+1V
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
R1
R1 = 10kΩ ±5%
5
+15V
+1V
HS-0508RH, HS-0509RH
Die Characteristics
DIE DIMENSIONS:
Backside Finish:
81.9mils x 90.2mils x 19mils
Silicon
INTERFACE MATERIALS:
ASSEMBLY RELATED INFORMATION:
Glassivation:
Substrate Potential:
Type: Nitride
Thickness: 7kÅ ±0.7kÅ
Unbiased (DI)
ADDITIONAL INFORMATION:
Top Metallization:
Worst Case Current Density:
Type: Al
Thickness: 16kÅ ±2kÅ
< 2.0 x 105 A/cm2
Transistor Count:
Substrate:
HS-0508RH
HS-0509RH
CMOS
Dielectric Isolation
243
243
Metallization Mask Layout
HS-0508RH
HS-0509RH
EN A0 A1 A2
GND
EN A0 A1
GND
-VSUP
+VSUP
-VSUP
+VSUP
IN 1
IN 5
IN 1A
IN 1B
IN 2
IN 6
IN 2A
IN 2B
IN 3
IN 3A
IN 7
IN 4 OUT
IN 8
NOTE:
IN 3B
IN 4A OUT A
OUT B IN 4B
Pad numbers correspond to DIP pin numbers only.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
6
ASIA
Intersil (Taiwan) Ltd.
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
Similar pages