BOARDCOM HSMS-285B Surface mount zero bias schottky detector diode Datasheet

HSMS-285x Series
Surface Mount Zero Bias Schottky Detector Diodes
Data Sheet
Description
Features
Avago’s HSMS-285x family of zero bias Schottky detector
­diodes has been designed and optim­ized for use in small
signal (Pin <-20 dBm) applications at ­frequencies below
1.5 GHz. They are ideal for RF/ID and RF Tag ­applications
where primary (DC bias) power is not available.
• Surface Mount SOT-23/SOT‑143 Packages
Important Note: For detector ­ applications with input
power ­levels greater than –20 dBm, use the HSMS-282x
series at frequencies ­below 4.0 GHz, and the HSMS-286x
series at frequencies above 4.0 GHz. The HSMS-285x
­series IS NOT ­ RECOMMENDED for these higher power
level ­applications.
Available in various package ­con­figurations, these detector ­ diodes provide low cost solutions to a wide variety
of design problems. Avago’s manufacturing techniques
­assure that when two diodes are mounted into a single
package, they are taken from ­adjacent sites on the wafer,
­assuring the highest possible ­degree of match.
• Miniature SOT-323 and SOT‑363 Packages
• High Detection Sensitivity:
up to 50 mV/µW at 915 MHz
• Low Flicker Noise:
-162 dBV/Hz at 100 Hz
• Low FIT (Failure in Time) Rate*
• Tape and Reel Options Available
• Matched Diodes for Consistent Performance
• Better Thermal Conductivity for Higher Power
Dissipation
• Lead-free
*
For more information see the Surface Mount Schottky Reliability
Data Sheet.
Attention: Observe precautions for
handling electrostatic ­sensitive devices.
ESD Machine Model (Class A)
ESD Human Body Model (Class 0)
Refer to Avago Application Note A004R:
Electrostatic Discharge Damage and Control.
Pin Connections and Package Marking
6
PLx
1
2
3
5
4
SOT-363 Package Lead Code Identification (top view)
Notes:
1. Package marking provides orientation and identification.
2. See “Electrical Specifications” for appropriate package marking.
SOT-23/SOT-143 Package Lead Code Identification (top view)
SINGLE
3
UNCONNECTED
TRIO
6
5
1
2
SERIES
3
L
4
6
3
1
BRIDGE
QUAD
5
2
4
P
3
SOT-323 Package Lead Code Identification (top view)
1
#0
2
1
#2
UNCONNECTED
PAIR
3
4
1
#5
2
2
SINGLE
3
SERIES
3
1
1
B
2
C
2
SOT-23/SOT-143 DC Electrical Specifications, TC = +25°C, Single Diode
Part
Number
HSMS-
Package
Marking
Lead
Code
Code
Configuration
Maximum
Forward
Voltage
VF (mV)
Maximum
Reverse
Leakage,
IR (µA)
2850
P0
0
Single
150
250
175
2852
P2
2
Series Pair [1,2]
2855
P5
5
Unconnected Pair[1,2]
Test
IF = 0.1 mA IF = 1.0 mA
VR=2V
Conditions
Typical
Capacitance
CT (pF)
0.30
VR = –0.5 V to –1.0V
f = 1 MHz
Notes:
1. ∆VF for diodes in pairs is 15.0 mV maximum at 1.0 mA.
2. ∆CT for diodes in pairs is 0.05 pF maximum at –0.5V.
SOT-323/SOT-363 DC Electrical Specifications, TC = +25°C, Single Diode
Part
Package
Number
Marking
Lead
HSMSCode
Code
Configuration
Maximum
Forward
Voltage
VF (mV)
Maximum Reverse
Typical
Leakage,
Capacitance
IR (µA)
CT (pF)
285B
P0
B
Single
150
250
175.
285C
P2
C
Series Pair
285L
PL
L
Unconnected Trio
285P
PP
P
Bridge Quad
Test
IF = 0.1 mA IF = 1.0 mA
VR=2V
Conditions
0.30
VR = 0.5 V to –1.0V
f = 1 MHz
Notes:
1. ∆VF for diodes in pairs is 15.0 mV maximum at 1.0 mA.
2. ∆CT for diodes in pairs is 0.05 pF maximum at –0.5V.
RF Electrical Specifications, TC = +25°C, Single Diode
Part Number
HSMS-
Typical Tangential Sensitivity
TSS (dBm) @ f = 915 MHz
2850
– 57
2852
2855
285B
285C
285L
285P
Test
Video Bandwidth = 2 MHz
Conditions
Zero Bias
Typical Voltage Sensitivity
g (mV/µW) @ f = 915 MHz
Typical Video
Resistance RV (KΩ)
40
8.0
Power in = –40 dBm
RL = 100 KΩ, Zero Bias
Zero Bias
Absolute Maximum Ratings, TC = +25°C, Single Diode
Symbol Parameter
Unit
PIV
Peak Inverse Voltage
V
TJ
Junction Temperature
°C
150
150
TSTG
Storage Temperature
°C
-65 to 150
-65 to 150
°C
-65 to 150
-65 to 150
°C/W
500
150
TOP
Operating Temperature
θ jc
Thermal Resistance[2]
ESD WARNING:
Handling Precautions Should Be Taken
To Avoid Static Discharge.
Absolute Maximum[1]
SOT-23/143
SOT-323/363
2.0
2.0
Notes:
1. Operation in excess of any one of these conditions may result in permanent damage to the
device.
2. TC = +25°C, where TC is defined to be the temperature at the package pins where contact is
made to the circuit board.
Equivalent Linear Circuit Model
Parameter
HSMS-285x chip
Rj
RS
Cj
RS = series resistance (see Table of SPICE parameters)
C j = junction capacitance (see Table of SPICE parameters)
Rj =
8.33 X 10-5 nT
Ib + Is
where
Ib = externally applied bias current in amps
Is = saturation current (see table of SPICE parameters)
T = temperature, °K
n = ideality factor (see table of SPICE parameters)
Note:
To effectively model the packaged HSMS-285x product,
please refer to Application Note AN1124.
SPICE Parameters
Units
BV
V
CJ0
pF
EG
eV
I BV
A
IS
A
N
RS
Ω
PB (VJ)
V
PT (XTI)
M
HSMS-285x
3.8
0.18
0.69
3 E -4
3 E-6
1.06
25
0.35
2
0.5
Typical Parameters, Single Diode
10000
1000
1
0.1
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
VF – FORWARD VOLTAGE (V)
Figure 1. Typical Forward Current
vs. Forward Voltage.
3.1
OUTPUT VOLTAGE (mV)
2.9
2.7
FREQUENCY = 2.45 GHz
PIN = -40 dBm
RL = 100 KΩ
2.5
2.3
2.1
1.9
1.7
1.5
1.3
MEASUREMENTS MADE USING A
1.1 FR4 MICROSTRIP CIRCUIT.
0.9
0 10 20 30 40 50 60 70 80 90 100
TEMPERATURE (°C)
Figure 4. Output Voltage vs.
Temperature.
915 MHz
VOLTAGE OUT (mV)
10
0.01
30
RL = 100 KΩ
VOLTAGE OUT (mV)
IF – FORWARD CURRENT (mA)
100
100
10
1
0.1
-50
DIODES TESTED IN FIXED-TUNED
FR4 MICROSTRIP CIRCUITS.
-40
-30
-20
-10
0
POWER IN (dBm)
Figure 2. +25°C Output Voltage vs.
Input Power at Zero Bias.
RL = 100 KΩ
10
915 MHz
1
0.3
-50
DIODES TESTED IN FIXED-TUNED
FR4 MICROSTRIP CIRCUITS.
-40
-30
POWER IN (dBm)
Figure 3. +25°C Expanded Output
Voltage vs. Input Power. See Figure 2.
-5
R j = 8.33 X 10 n T = RV– Rs
+the
I b Schottky Barrier
The HeightIof
S
Appli­cations Information
Introduction
Avago’s HSMS‑285x family of Schottky detector diodes
has been developed specifically for low cost, high
volume designs in small signal (Pin < -20 dBm) applications at frequencies below 1.5 GHz. At higher frequencies, the DC biased HSMS-286x family should be considered.
In large signal power or gain control applications
(Pin > ‑20 dBm), the HSMS-282x and HSMS-286x products should be used. The HSMS-285x zero bias diode is
not designed for large signal designs.
Schottky Barrier Diode ­Characteristics
Stripped of its package, a Schottky barrier diode chip
­consists of a metal-semiconductor barrier formed by deposition of a metal layer on a semiconductor. The most
common of several ­different types, the passivated ­diode,
is shown in Figure 5, along with its equivalent circuit.
RS
METAL
PASSIVATION
N-TYPE OR P-TYPE EPI
PASSIVATION
LAYER
SCHOTTKY JUNCTION
Cj
Rj
N-TYPE OR P-TYPE SILICON SUBSTRATE
CROSS-SECTION OF SCHOTTKY
BARRIER DIODE CHIP
EQUIVALENT
CIRCUIT
Figure 5. Schottky Diode Chip.
RS is the parasitic series ­resistance of the diode, the sum
of the bondwire and leadframe ­resistance, the resistance
HSMS-285A/6A fig 9
of the bulk layer of silicon, etc. RF ­ energy coupled into
RS is lost as heat — it does not contribute to the rectified
output of the diode. CJ is parasitic junction capaci­tance
of the diode, controlled by the thickness of the epitaxial
layer and the diameter of the Schottky contact. Rj is the
junction ­resistance of the diode, a function of the total
current flowing through it.
-5
R j = 8.33 X 10 n T = RV– Rs
IS + Ib
=
0.026
at 25°C
I S + Ib
where
V -(see
IRS table of SPICE parameters)
n = ideality factor
I = IS (exp
T = temperature
in °K - 1)
0.026
IS = saturation current (see table of SPICE parameters)
Ib = externally applied bias current in amps
RS = Rd – 0.026
IS is a function
of diode
If barrier height, and can range
from picoamps for high barrier diodes to as much as 5
µA for very low barrier diodes.
RV ≈ 26,000
IS + Ib
(
)
The current-voltage
character­istic of a Schottky barrier
0.026
= at room temperature
at 25°C
diode
is described by the following
I +I
equation: S b
I = IS (exp
V - IR
( 0.026
) - 1)
S
On a semi-log plot (as shown in the Avago catalog) the
RS = graph
Rd – 0.026
current
will be a straight line with inverse slope
If
2.3 X 0.026 = 0.060
volts per cycle (until the effect of RS is
seen in a curve that droops at high current). All Schottky
­diode curves
have the same slope, but not necessarRV ≈ 26,000
ily the same
value
IS + Ib of current for a given voltage. This is
deter­mined by
the saturation current, IS, and is related to
the barrier height of the diode.
Through the choice of p-type or n‑type silicon, and the
selection of metal, one can tailor the characteristics of a
Schottky diode. ­Barrier height will be altered, and at the
same time CJ and RS will be changed. In general, very
low ­ barrier height diodes (with high values of IS, suitable for zero bias applica­tions) are realized on ­­ p‑type
silicon. Such diodes suffer from higher values of RS than
do the n‑type. Thus, p-type diodes are generally reserved
for small signal detector applications (where very high
values of RV swamp out high RS) and n-type diodes are
used for mixer applications (where high L.O. drive levels
keep RV low).
Measuring Diode Parameters
The measurement of the five ­ elements which make up
the low frequency equivalent circuit for a pack­aged
Schottky diode (see ­Figure 6) is a complex task. ­Various
techniques are used for each element. The task begins
with the elements of the diode chip itself.
CP
LP
RV
RS
Cj
FOR THE HSMS-285x SERIES
CP = 0.08 pF
LP = 2 nH
Cj = 0.18 pF
RS = 25 Ω
RV = 9 KΩ
Figure 6. Equivalent Circuit of a Schottky Diode.
-5
R j = 8.33 X 10 n T = RV– Rs
IS + Ib
0.026
=
at 25°C
I S + Ib
RS is perhaps
the easiest to ­measure accurately. The V-I
curve is measured for the diode under forward bias, and
- IRScurve is taken at some relatively high
the slope ofVthe
I = IS (exp
- 1)as 5 mA). This slope is converted
value
of current (such
0.026
into a resistance Rd.
(
)
RS = Rd – 0.026
If
RV and CJ are very difficult to measure. Consider the
imped­ance26,000
of CJ = 0.16 pF when measured at 1 MHz — it
RV ≈
is approximately
IS + Ib 1 MΩ. For a well designed zero bias
Schottky, RV is in the range of 5 to 25 KΩ, and it shorts
out the junction capacitance. Moving up to a higher frequency enables the measurement of the capaci­tance,
but it then shorts out the video ­resistance. The best measurement technique is to mount the diode in series in a
50 Ω microstrip test ­circuit and measure its insertion loss
at low power levels (around -20 dBm) using an HP8753C
­network analyzer. The resulting display will appear as
shown in Figure 7.
Detector Circuits
When DC bias is available, Schottky diode detector circuits can be used to create low cost RF and microwave receivers with a sensitivity of -55 dBm to
-57 dBm.[1] These circuits can take a variety of forms,
but in the most simple case they appear as shown in
Figure 8. This is the basic ­detector circuit used with the
HSMS‑285x family of diodes.
In the design of such detector ­circuits, the starting point is
the equivalent circuit of the diode, as shown in Figure 6.
Of interest in the design of the video portion of the
circuit is the diode’s video impedance — the other
four elements of the equiv­alent circuit disappear at all
­reasonable video frequencies. In general, the lower the
diode’s video impedance, the better the design.
RF
IN
Z-MATCH
NETWORK
VIDEO
OUT
-10
50 Ω
INSERTION LOSS (dB)
-15
0.16 pF
50 Ω
-20
IS + Ib
-25
0.026
I S + Ib
at 25°C
Figure=8. Basic Detector ­
Circuits.
50 Ω 9 KΩ
-30
50 Ω
-35
-40
Z-MATCH
RF
8.33
X 10-5 n T = RVIDEO
R j = NETWORK
– Rs
OUT
IN
V
3
10
100
1000 3000
FREQUENCY (MHz)
Figure 7. Measuring C J and RV.
At frequencies
below 10 MHz, the video resistance domHSMS-285A/6A fig 10
inates the loss and can easily be calcu­lated from it. At
frequencies above 300 MHz, the junction capacitance
sets the loss, which plots out as a straight line when
frequency is plotted on a log scale. Again, ­calculation is
straightforward.
LP and CP are best measured on the HP8753C, with the
diode ­terminating a 50 Ω line on the ­input port. The resulting tabulation of S11 can be put into a ­ microwave
linear analysis ­ program having the five element equivalent circuit with RV, CJ and RS fixed. The optimizer can
then adjust the values of LP and CP ­until the ­calculated
S11 matches the measured values. Note that extreme
care must be taken to ­ de‑embed the parasitics of the
50 Ω test fixture.
The situation is somewhat more complicated in the
design of the
V -RF
IRS impedance matching net­work, which
I = IS (exp the pack­age ­
- 1) inductance and capacitance
includes
0.026
(which can be
tuned out), the ­series resistance, the junction ­capacitance and the video ­resistance. Of these five
elements of the
diode’s equiv­alent circuit, the four paraR = Rd – 0.026
sitics Sare constants
If and the video resistance is a ­function
of the current flowing through the diode.
(
)
RV ≈ 26,000
IS + Ib
where
IS = diode saturation current in µA
Ib = bias current in µA
Saturation current is a function of the diode’s design,[2] and
it is a constant at a given tempera­ture. For the HSMS-285x
series, it is typically 3 to 5 µA at 25°C.
Saturation current sets the detection sensitivity, video resistance and input RF impedance of the zero bias Schottky
detector diode. Since no external bias is used with the
HSMS-285x series, a single transfer curve at any given frequency is obtained, as shown in Figure 2.
[1] Avago Application Note 923, Schottky Barrier Diode Video Detectors.
The most difficult part of the ­design of a detector circuit
is the input impedance matching ­ network. For very
broadband ­detectors, a shunt 60 Ω resistor will give good
input match, but at the expense of detection ­sensitivity.
When maximum sensitivity is ­ required over a narrow
band of frequencies, a reactive matching network
is optimum. Such net­works can be realized in either
lumped or distributed elements, depending upon frequency, size constraints and cost limitations, but certain
general design ­ principals exist for all types.[3] ­ Design
work begins with the RF impedance of the HSMS-285x
­series, which is given in Figure 9.
FREQUENCY (GHz): 0.9-0.93
Figure 11. Input Impedance.
The input
match, expressed
in terms of return loss, is
HSMS-285A/6A
fig 15
given in Figure 12.
2
0.2
0.6
5
0
1
3
4
5
6
Figure 9. RF Impedance of the HSMS‑285x Series at-40 dBm.
915 MHz Detector Circuit
Figure 10 illustrates a simple ­ impedance matching
network for a 915 MHz detector.
65nH
VIDEO
OUT
WIDTH = 0.050"
LENGTH = 0.065"
-5
-10
-15
-20
0.9
HSMS-285A/6A fig 13
RF
INPUT
RETURN LOSS (dB)
1 GHz
2
100 pF
WIDTH = 0.015"
LENGTH = 0.600"
TRANSMISSION LINE
DIMENSIONS ARE FOR
MICROSTRIP ON
0.032" THICK FR-4.
Figure 10. 915 MHz Matching Network for the HSMS-285x Series at Zero Bias.
0.915
0.93
FREQUENCY (GHz)
Figure 12. Input Return Loss.
As can be seen,
the band
HSMS-285A/6A
fig 16over which a good match is
achieved is more than adequate for 915 MHz RFID applications.
Voltage Doublers
To this point, we have restricted our discus­sion to single
diode ­ detectors. A glance at Figure 8, however, will lead
to the suggestion that the two types of single diode detectors be combined into a two diode voltage doubler[4]
(known also as a full wave rectifier). Such a detector is
shown in Figure 13.
A 65 nH inductor rotates the ­impedance of the diode to
Z-MATCH
a point on the
Smith Chart
HSMS-285A/6A
fig 14 where a shunt inductor can
RF IN
NETWORK
pull it up to the ­center. The short length of 0.065" wide
microstrip line is used to mount the lead of the diode’s
SOT‑323 package. A shorted shunt stub of length <λ/4
provides the necessary shunt inductance and simul­
Figure 13. Voltage Doubler Circuit.
taneously provides the ­ return circuit for the current
generated in the diode. The impedance of this circuit is
given in Figure 11.
HSMS-285X fig 11 was 7
VIDEO OUT
[2] Avago Application Note 969, An Optimum Zero Bias Schottky Detector Diode.
[3] Avago Application Note 963, Impedance Matching Techniques for Mixers
and Detectors.
Such a circuit offers several ­advantages. First the voltage
­outputs of two diodes are added in series, increasing the
overall value of voltage sensitivity for the network (compared to a single ­diode detector). Second, the RF impedances of the two diodes are added in parallel, making
the job of reactive matching a bit easier. Such a circuit
can easily be ­realized using the two series diodes in the
HSMS-285C.
Flicker Noise
Reference to Figure 5 will show that there is a junction of metal, silicon, and passivation around the rim
of the Schottky contact. It is in this three-way junction
that flicker noise[5] is generated. This noise can severely
reduce the ­ sensitivity of a crystal video ­ receiver utilizing a Schottky ­detector circuit if the video ­frequency is
below the noise ­corner. Flicker noise can be ­substantially
reduced by the ­ elimination of passivation, but such
diodes cannot be mounted in non-hermetic packages.
p‑type silicon Schottky diodes have the least flicker noise
at a given value of external bias (compared to n‑type
silicon or GaAs). At zero bias, such diodes can have
­extremely low values of flicker noise. For the HSMS-285x
series, the noise temperature ratio is given in Figure 14.
Avago offers a com­plete line of surface mountable
PIN limiter ­ diodes. Most notably, our HSMP‑4820 (SOT23) can act as a very fast (nanosecond) power-sensitive switch when placed ­ between the antenna and the
Schottky diode, shorting out the RF circuit temporarily and ­ reflecting the excessive RF energy back out the
antenna.
Assembly Instructions
SOT-323 PCB Footprint
A recommended PCB pad layout for the miniature SOT323 (SC-70) package is shown in Figure 15 (dimensions
are in inches). This layout provides ample allowance for
package placement by automated assembly equipment
without adding parasitics that could impair the performance. Figure 16 shows the pad layout for the six-lead
SOT-363.
15
NOISE TEMPERATURE RATIO (dB)
Any Schottky junction, be it an RF diode or the gate of
a MESFET, is relatively delicate and can be burned out
with excessive RF power. Many crystal video receivers
used in RFID (tag) applications find themselves in poorly
controlled environments where high power sources may
be present. Examples are the areas around airport and
FAA radars, nearby ham radio operators, the vicinity of
a broadcast band transmitter, etc. In such environments,
the Schottky diodes of the ­ receiver can be protected
by a device known as a limiter diode.[6] Formerly available only in radar warning receivers and other high cost
electronic warfare applications, these diodes have been
adapted to commercial and ­consumer circuits.
10
5
0
0.026
-5
10
100
1000
10000
100000
0.026
FREQUENCY (Hz)
Diode Burnout
0.075
0.079
Figure 14. Typical Noise ­Temperature Ratio.
Noise temperature ratio is the quotient of the diode’s
noise power (expressed in dBV/Hz) divided by the noise
power of an ideal resistor of resistance R = RV.
For an ideal resistor R, at 300°K, the noise voltage can be
computed from
v = 1.287 X
10-10
√R volts/Hz
0.035
0.039
0.022
0.016
Dimensions in inches
Figure 15. Recommended PCB
Pad Layout for Avago’s SC70
3L/SOT‑323 Products.
Figure 16. Recommended PCB Pad
Layout for Avago's SC70 6L/SOT‑363
Products.
which can be expressed as
20 log10 v
dBV/Hz
Thus, for a diode with RV = 9 KΩ, the noise voltage is
12.2 nV/Hz or -158 dBV/Hz. On the graph of ­Figure 14, 158 dBV/Hz would ­replace the zero on the vertical scale
to convert the chart to one of absolute noise voltage vs.
­frequency.
[4] Avago Application Note 956-4, Schottky Diode Voltage Doubler.
[5] Avago Application Note 965-3, Flicker Noise in Schottky Diodes.
[6] Avago Application Note 1050, Low Cost, Surface Mount Power Limiters.
SMT Assembly
Reliable assembly of surface mount components is a
complex process that involves many material, process,
and equipment factors, including: method of heating
(e.g., IR or vapor phase reflow, wave soldering, etc.)
circuit board material, conductor thickness and pattern,
type of solder alloy, and the thermal conductivity and
thermal mass of components. Components with a low
mass, such as the SOT packages, will reach solder reflow
temperatures faster than those with a greater mass.
zones. The preheat zones increase the temperature of
the board and components to prevent thermal shock
and begin evaporating solvents from the solder paste.
The reflow zone briefly elevates the temperature sufficiently to produce a reflow of the solder.
The rates of change of temperature for the ramp-up and
cool-down zones are chosen to be low enough to not
cause deformation of the board or damage to components due to thermal shock. The maximum temperature
in the reflow zone (TMAX) should not exceed 260°C.
Avago’s diodes have been qualified to the time-temperature profile shown in Figure 17. This profile is representative of an IR reflow type of surface mount assembly
process.
These parameters are typical for a surface mount assembly process for Avago diodes. As a general guideline, the
circuit board and components should be exposed only to
the minimum temperatures and times necessary to achieve
a uniform reflow of solder.
After ramping up from room temperature, the circuit
board with components attached to it (held in place
with solder paste) passes through one or more preheat
tp
Tp
Critical Zone
T L to Tp
Ramp-up
Temperature
TL
Ts
Ts
tL
max
min
Ramp-down
ts
Preheat
25
t 25° C to Peak
Time
Figure 17. Surface Mount Assembly Profile.
Lead-Free Reflow Profile Recommendation (IPC/JEDEC J-STD-020C)
Reflow Parameter
Lead-Free Assembly
Average ramp-up rate (Liquidus Temperature (TS(max) to Peak)
3°C/ second max
Preheat
Temperature Min (TS(min))
150°C
Temperature Max (TS(max))
200°C
Time (min to max) (tS)
60-180 seconds
Ts(max) to TL Ramp-up Rate
Time maintained above:
3°C/second max
Temperature (TL)
217°C
Time (tL)
60-150 seconds
Peak Temperature (TP)
260 +0/-5°C
Time within 5 °C of actual
Peak temperature (tP)
20-40 seconds
Ramp-down Rate
6°C/second max
Time 25 °C to Peak Temperature
8 minutes max
Note 1: All temperatures refer to topside of the package, measured on the package body surface
Part Number Ordering Information
Part Number
No. of
Devices
Container
HSMS-285x-TR2G
10000
13" Reel
HSMS-285x-TR1G
3000
7" Reel
HSMS-285x-BLK G
100
antistatic bag
where x = 0, 2, 5, B, C, L and P for HSMS-285x.
Package Dimensions
Outline 23 (SOT-23)
Outline SOT-323 (SC-70 3 Lead)
e1
e2
e1
XXX
E
XXX
E
E1
e
e
DIMENSIONS (mm)
C
DIMENSIONS (mm)
D
A
10
C
D
B
Notes:
XXX-package marking
Drawings are not to scale
L
B
L
A1
E1
SYMBOL
A
A1
B
C
D
E1
e
e1
e2
E
L
MIN.
0.79
0.000
0.30
0.08
2.73
1.15
0.89
1.78
0.45
2.10
0.45
MAX.
1.20
0.100
0.54
0.20
3.13
1.50
1.02
2.04
0.60
2.70
0.69
A
A1
Notes:
XXX-package marking
Drawings are not to scale
SYMBOL
A
A1
B
C
D
E1
e
e1
E
L
MIN.
MAX.
0.80
1.00
0.00
0.10
0.15
0.40
0.08
0.25
1.80
2.25
1.10
1.40
0.65 typical
1.30 typical
1.80
2.40
0.26
0.46
Outline 143 (SOT-143)
Outline SOT-363 (SC-70 6 Lead)
e2
e1
HE
B1
XXX
E
E
E1
L
e
c
D
DIMENSIONS (mm)
L
B
e
SYMBOL
E
D
HE
A
A2
A1
e
b
c
L
C
A1
A2
DIMENSIONS (mm)
D
A
A1
Notes:
XXX-package marking
Drawings are not to scale
SYMBOL
A
A1
B
B1
C
D
E1
e
e1
e2
E
L
MIN.
0.79
0.013
0.36
0.76
0.086
2.80
1.20
0.89
1.78
0.45
2.10
0.45
Device Orientation
MAX.
1.097
0.10
0.54
0.92
0.152
3.06
1.40
1.02
2.04
0.60
2.65
0.69
A
b
MIN.
MAX.
1.15
1.35
1.80
2.25
1.80
2.40
0.80
1.10
0.80
1.00
0.00
0.10
0.650 BCS
0.15
0.30
0.08
0.25
0.10
0.46
For Outlines SOT-23, -323
REEL
TOP VIEW
END VIEW
4 mm
CARRIER
TAPE
8 mm
USER
FEED
DIRECTION
ABC
For Outline SOT-143
ABC
For Outline SOT-363
TOP VIEW
END VIEW
TOP VIEW
4 mm
END VIEW
4 mm
ABC
ABC
ABC
ABC
Note: "AB" represents package marking code.
"C" represents date code.
11
ABC
Note: "AB" represents package marking code.
"C" represents date code.
COVER TAPE
8 mm
ABC
8 mm
ABC
ABC
ABC
ABC
Note: "AB" represents package marking code.
"C" represents date code.
Tape Dimensions and Product Orientation
For Outline SOT-23
P
P2
D
E
P0
F
W
D1
t1
Ko
9° MAX
13.5° MAX
8° MAX
B0
A0
DESCRIPTION
SYMBOL
SIZE (mm)
SIZE (INCHES)
CAVITY
LENGTH
WIDTH
DEPTH
PITCH
BOTTOM HOLE DIAMETER
A0
B0
K0
P
D1
3.15 ± 0.10
2.77 ± 0.10
1.22 ± 0.10
4.00 ± 0.10
1.00 + 0.05
0.124 ± 0.004
0.109 ± 0.004
0.048 ± 0.004
0.157 ± 0.004
0.039 ± 0.002
PERFORATION
DIAMETER
PITCH
POSITION
D
P0
E
1.50 + 0.10
4.00 ± 0.10
1.75 ± 0.10
0.059 + 0.004
0.157 ± 0.004
0.069 ± 0.004
CARRIER TAPE
WIDTH
THICKNESS
W
t1
8.00 +0.30 –0.10
0.229 ± 0.013
0.315 +0.012 –0.004
0.009 ± 0.0005
DISTANCE
BETWEEN
CENTERLINE
CAVITY TO PERFORATION
(WIDTH DIRECTION)
F
3.50 ± 0.05
0.138 ± 0.002
CAVITY TO PERFORATION
(LENGTH DIRECTION)
P2
2.00 ± 0.05
0.079 ± 0.002
For Outline SOT-143
P
D
P2
P0
E
F
W
D1
t1
K0
9° MAX
9° MAX
A0
B0
DESCRIPTION
SYMBOL
SIZE (mm)
SIZE (INCHES)
CAVITY
LENGTH
WIDTH
DEPTH
PITCH
BOTTOM HOLE DIAMETER
A0
B0
K0
P
D1
3.19 ± 0.10
2.80 ± 0.10
1.31 ± 0.10
4.00 ± 0.10
1.00 + 0.25
0.126 ± 0.004
0.110 ± 0.004
0.052 ± 0.004
0.157 ± 0.004
0.039 + 0.010
PERFORATION
DIAMETER
PITCH
POSITION
D
P0
E
1.50 + 0.10
4.00 ± 0.10
1.75 ± 0.10
0.059 + 0.004
0.157 ± 0.004
0.069 ± 0.004
CARRIER TAPE
WIDTH
THICKNESS
W
t1
8.00 +0.30 –0.10
0.254 ± 0.013
0.315+0.012 –0.004
0.0100 ± 0.0005
DISTANCE
CAVITY TO PERFORATION
(WIDTH DIRECTION)
F
3.50 ± 0.05
0.138 ± 0.002
CAVITY TO PERFORATION
(LENGTH DIRECTION)
P2
2.00 ± 0.05
0.079 ± 0.002
12
Tape Dimensions and Product Orientation
For Outlines SOT-323, -363
P
P2
D
P0
E
F
W
C
D1
t1 (CARRIER TAPE THICKNESS)
K0
An
A0
DESCRIPTION
SYMBOL
SIZE (mm)
SIZE (INCHES)
LENGTH
WIDTH
DEPTH
PITCH
BOTTOM HOLE DIAMETER
A0
B0
K0
P
D1
2.40 ± 0.10
2.40 ± 0.10
1.20 ± 0.10
4.00 ± 0.10
1.00 + 0.25
0.094 ± 0.004
0.094 ± 0.004
0.047 ± 0.004
0.157 ± 0.004
0.039 + 0.010
PERFORATION
DIAMETER
PITCH
POSITION
D
P0
E
1.55 ± 0.05
4.00 ± 0.10
1.75 ± 0.10
0.061 ± 0.002
0.157 ± 0.004
0.069 ± 0.004
CARRIER TAPE
WIDTH
THICKNESS
W
t1
8.00 ± 0.30
0.254 ± 0.02
0.315 ± 0.012
0.0100 ± 0.0008
COVER TAPE
WIDTH
TAPE THICKNESS
C
Tt
5.4 ± 0.10
0.062 ± 0.001
0.205 ± 0.004
0.0025 ± 0.00004
DISTANCE
CAVITY TO PERFORATION
(WIDTH DIRECTION)
F
3.50 ± 0.05
0.138 ± 0.002
CAVITY TO PERFORATION
(LENGTH DIRECTION)
P2
2.00 ± 0.05
0.079 ± 0.002
FOR SOT-323 (SC70-3 LEAD)
An
8°C MAX
FOR SOT-363 (SC70-6 LEAD)
An
B0
CAVITY
ANGLE
Tt (COVER TAPE THICKNESS)
10°C MAX
For product information and a complete list of distributors, please go to our web site:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. Obsoletes 5989-4022EN
AV02-1377EN - May 29, 2009
Similar pages