Holtek HT49CV5 A/d with vfd type 8-bit mcu Datasheet

HT49RV5/HT49CV5
A/D With VFD Type 8-Bit MCU
Technical Document
· Tools Information
· FAQs
· Application Note
- HA0077E HT49CVX Remote Control Receiver SWIP Design Note
- HA0078E HT49CVX Display SWIP Design Note
Features
· Operating voltage:
· 8-bit prescaler for RTC
fSYS=4MHz: 2.2V~5.5V
fSYS=8MHz: 3.3V~5.5V
· Watchdog Timer
· Buzzer output
· 20 bidirectional I/O lines (PA, PB, PC, PD)
· On-chip crystal, RC and 32768Hz crystal oscillator
· Two external interrupt inputs
· HALT function and wake-up feature reduce power
· Two 16-bit programmable timer/event counters with
consumption
PFD (programmable frequency divider) function
· 8-level subroutine nesting
· One 8-bit Remote Control Timer (RMT), pin-shared
· 4-channel 8-bit resolution A/D converter
with PC7
· 2-channel 8-bit PWM output shared with 2 I/O lines
· Single channel serial interface
· Low voltage reset function
· VFD driver with 11´11 segments
· Bit manipulation instruction
(16-segment & 4-grid to 11-segment & 11-grid)
· 16-bit table read instruction
· 4K´16 program memory
· Up to 0.5ms instruction cycle with 8MHz system clock
· 192´8 data memory RAM
· 63 powerful instructions
· Supports PFD for sound generation
· All instructions in 1 or 2 machine cycles
· Real Time Clock (RTC)
· 56-pin SSOP package
General Description
driver they are suitable for use in products which require
a front panel for their operation such as DVDs, VCDs,
Mini-component audio systems, cassette decks, tuners,
CD players, other home appliances, etc.
The HT49RV5/HT49CV5 are 8-bit high performance
single chip MCUs. Their single cycle instruction and
2-stage pipeline architecture make them suitable for
high speed applications. As the devices include an VFD
Rev. 1.20
1
April 14, 2006
HT49RV5/HT49CV5
Block Diagram
In te rru p t
C ir c u it
M
T M R 1 C
T M R 1
P F D 1
IN T C
M
M P
U
U
fS
X
U
M
S T A T U S
A L U
fS
U
Y S
R T C
X
P D
P D
P D
P D
P D
P O R T D
P D
S h ifte r
/4
O S C 3
O S C
O S C 4
0 /
4 /
5 /
6 /
7 /
P W
IN
IN
T M
T M
M 0 ~ P D 1 /P W
T 0
T 1
R 0
R 1
M 1
4 -C h a n n e l
A /D C o n v e rte r
P B C
B P
S
/4
X
P W M
P D C
T im in g
G e n e r a tio n
Y S
3 2 7 6 8 H z
W D T O S C
M U X
In s tr u c tio n
D e c o d e r
Y S
P D 6 /T M R 0
D a ta
M e m o ry
X
fS
P D 7 /T M R 1
M
W D T
O S
O S
V D
V S
R E
X
R T C
In s tr u c tio n
R e g is te r
O S C 2
O S C 4
U
P F D 0
S ta c k
P ro g ra m
C o u n te r
P ro g ra m
R O M
P r e s c a le r
M
T M R 0 C
T M R 0
A C C
D
C 1
C 3
V F D
M e m o ry
P A C
E N /D IS
H A L T
S E G 1 1 /G r id 1 0 ~
S E G 1 5 /G r id 6
P A 0
P A 1
P A 2
P A 3
P A 4
P O R T A
P A
V F D D r iv e r
G r id 0 ~
G r id 5
P B 0 /A N 0 ~ P B 3 /A N 3
P B
S
V E E
P O R T B
/B Z
/B Z
/P F D
~ P A 7
L V R
S E G 0 ~
S E G 1 0
P C C
P O R T C
P C 6
P C 7 /R M T
P C
S D I
S D O
S C K
S e r ia l In te r fa c e
S C S
M U X
fS
fR
8 - b it R e m o te
C o n tr o l T im e r
Rev. 1.20
2
Y S /4
T C O S C
R M T
April 14, 2006
HT49RV5/HT49CV5
Pin Assignment
O S C 2
1
5 6
V D D
O S C 1
2
5 5
O S C 3
O S C 4
R E S
3
5 4
P A 0 /B Z
4
5 3
S D I
P A 1 /B Z
5
5 2
S D O
P A 2
6
5 1
S C K
P A 3 /P F D
7
5 0
S C S
P A 4
8
4 9
G R ID 0
P A 5
9
4 8
G R ID 1
P A 6
1 0
4 7
G R ID 2
P A 7
1 1
4 6
G R ID 3
P B 0 /A N 0
1 2
4 5
G R ID 4
P B 1 /A N 1
1 3
4 4
G R ID 5
P B 2 /A N 2
1 4
4 3
V D D
P B 3 /A N 3
1 5
4 2
V E E
V S S
1 6
4 1
S E G 1 5 /G R ID 6
P D 0 /P W M 0
1 7
4 0
S E G 1 4 /G R ID 7
P D 1 /P W M 1
1 8
3 9
S E G 1 3 /G R ID 8
P D 4 /IN T 0
1 9
3 8
S E G 1 2 /G R ID 9
P D 5 /IN T 1
2 0
3 7
S E G 1 1 /G R ID 1 0
P D 6 /T M R 0
2 1
3 6
S E G 1 0
P D 7 /T M R 1
2 2
3 5
S E G 9
V S S
2 3
3 4
S E G 8
P C 6
2 4
3 3
S E G 7
P C 7 /R M T
2 5
3 2
S E G 6
S E G 0
2 6
3 1
S E G 5
S E G 1
2 7
3 0
S E G 4
S E G 2
2 8
2 9
S E G 3
H T 4 9 R V 5 /H T 4 9 C V 5
5 6 S S O P -A
Note:
Each VDD (VSS) pins must be connected to the power (ground) of the system.
Pin Description
Pin Name
PA0/BZ
PA1/BZ
PA2
PA3/PFD
PA4~PA7
PB0/AN0~
PB3/AN3
PC6
PC7/RMT
Rev. 1.20
I/O
Options
Description
I/O
Wake-up
Pull-high
Buzzer
PFD
Bidirectional 8-bit input/output port. Each bit can be configured as a wake-up
input by configuration option. Software instructions determine if the pin is a
CMOS output or Schmitt trigger input with or without pull-high resistor (determined by pull-high options: bit option). Pins PA0, PA1 and PA3 are
pin-shared with BZ, BZ and PFD, respectively.
Pull-high
Bidirectional 4-bit input/output port. Software instructions determine if the pin
is a CMOS output or Schmitt trigger input with or without pull-high resistor
(determined by pull-high option: bit option) or A/D input. Once a PB line is selected as an A/D input (by using software control), the I/O function and
pull-high resistor are disabled automatically.
I/O
I/O
Pull-high
Bidirectional 2-bit input/output port. Software instructions determine if the pin
is a CMOS output or Schmitt trigger input with or without pull-high resistor
(determined by pull-high option: bit option). RMT with wake-up function (both
rising and falling edge) and Schmitt trigger input with or without a pull-high resistor (determined by pull-high option).
Note:The RMT is pin-shared with PC7. When PC7/RMT pin uses as the input
mode of RMT function , suggesting the user to set PC7 as input mode for
safety. And so that I/O function of PC7 will not influence the RMT input function.
3
April 14, 2006
HT49RV5/HT49CV5
Pin Name
PD0/PWM0
PD1/PWM1
I/O
I/O
Options
Description
Pull-high
PWM
Bidirectional 2-bit input/output port. Software instructions determine if the pin
is a CMOS output or Schmitt trigger input with or without a pull-high resistor
(determined by pull-high option: bit option). PD0~PD1 are pin-shared with
PWM0~PWM1 (dependent on Mask options).
Bidirectional 4-bit input/output port. Software instructions determine if the pin
is a CMOS output or Schmitt trigger input with or without a pull-high resistor
(determined by pull-high option: bit option). Pins PD4~PD7 are pin-shared
with INT0, INT1, TMR0 & TMR1, respectively (determined by software control).
PD4/INT0
PD5/INT1
PD6/TMR0
PD7/TMR1
I/O
Pull-high
VSS
¾
¾
Negative power supply, ground
VEE
¾
¾
VFD Negative power supply
SEG0~SEG10
O
¾
High voltage segment output for VFD panel.
SEG11/Grid10~
SEG15/Grid6
O
¾
High voltage output for VFD panel. These pins are selectable for segment or
grid output.
Grid0~Grid5
O
¾
High voltage grid output for VFD panel.
SDI
I
¾
Serial interface serial data input
SDO
O
¾
Serial interface serial data output
SCK
I/O
¾
Serial interface serial clock input/output (initial ²input²).
SCS
I/O
¾
Serial interface chip select pin, output for master mode, input for slave mode.
OSC4
OSC3
O
I
VDD
¾
¾
OSC2
OSC1
O
I
Crystal or RC
RES
I
¾
Real time clock oscillators. OSC3 and OSC4 are connected to a 32768Hz
RTC or
crystal oscillator for timing purposes or to a system clock source (depending
System Clock
on the options). No built-in capacitor.
Positive power supply
OSC1 and OSC2 are connected to an RC network or a crystal (by options) for
the internal system clock. For RC operation, OSC2 is an output pin for 1/4
system clock. The system clock may come from the RTC oscillator. If the system clock comes from RTCOSC, these two pins can be left floating.
Schmitt trigger reset input, active low
Absolute Maximum Ratings
Supply Voltage ...........................VSS-0.3V to VSS+6.0V
Storage Temperature ............................-50°C to 125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
Operating Temperature...........................-40°C to 85°C
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 1.20
4
April 14, 2006
HT49RV5/HT49CV5
D.C. Characteristics
Symbol
Parameter
VDD
Operating Voltage
VEE
VFD Supply Voltage
IDD1
Operating Current (Crystal OSC)
IDD2
Operating Current (RC OSC)
IDD3
Operating Current
(fSYS=32768Hz)
Ta=25°C
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
¾
fSYS=4MHz
2.2
¾
5.5
V
¾
fSYS=8MHz
3.3
¾
5.5
V
¾
0
¾
VDD-30
V
No load, ADC off, VFD off,
fSYS=4MHz
¾
2.0
3.0
mA
¾
5.0
8.0
mA
No load, ADC off, VFD off,
fSYS=4MHz
¾
1.8
2.7
mA
¾
4.6
7.5
mA
¾
1.2
2
mA
¾
3V
5V
3V
5V
3V
5V
3V
IDD4
Operating Current (Crystal OSC)
ISTB1
Standby Current (*fS=T1)
ISTB2
Standby Current
(*fS=32768Hz OSC)
3V
VIL1
Input Low Voltage for I/O Ports,
TMR and INT
3V
VIH1
Input High Voltage for I/O Ports,
TMR and INT
3V
VIL2
Input Low Voltage (RES)
VIH2
Input High Voltage (RES)
IOL
I/O Port Sink Current
5V
3V
5V
5V
No load, ADC off, VFD off
¾
4
7
mA
No load, ADC off, VFD on,
fSYS=4MHz
¾
3.5
4.5
mA
¾
7.5
12
mA
No load, system HALT
VFD off at HALT
¾
¾
1
mA
¾
¾
2
mA
No load, system HALT
VFD off at HALT
¾
4
10
mA
¾
14
20
mA
¾
0
¾
0.2VDD
V
¾
0.8VDD
¾
VDD
V
¾
0
¾
0.4VDD
V
¾
0.9VDD
¾
VDD
V
6
12
¾
mA
10
25
¾
mA
-2
-4
¾
mA
-5
-8
¾
mA
5V
5V
3V
5V
3V
5V
3V
5V
3V
VOL=0.1VDD
VOH=0.9VDD
IOH1
I/O Port Source Current
IOH2
Grid Source Current
5V
VOH=VDD-2V
-15
¾
¾
mA
IOH3
Segment Source Current
5V
VOH=VDD-2V
-3
¾
¾
mA
RPH
Pull-high Resistance of I/O Ports
and INT0, INT1
3V
¾
20
60
100
kW
5V
¾
10
30
50
kW
RPL
VFD Driver Output Pull-low
Resistor
5V
¾
50
100
150
kW
VLVR
Low Voltage Reset Voltage
¾
2.7
3.0
3.3
V
VAD
A/D Input Voltage
¾
0
¾
VDD
V
¾
¾
±0.5
±1
LSB
¾
1
2
mA
¾
2
4
mA
EAD
A/D Conversion Error
IADC
Additional Power Consumption
if A/D Converter is Used
Note:
5V
LVR enabled
¾
3V
5V
3V
5V
No load
²*fS² Refer to WDT clock option
Rev. 1.20
5
April 14, 2006
HT49RV5/HT49CV5
A.C. Characteristics
Ta=25°C
Test Conditions
Symbol
Parameter
fSYS1
System Clock
Typ.
Max.
Unit
¾
2.2V~5.5V
400
¾
4000
kHz
¾
3.3V~5.5V
400
¾
8000
kHz
2.2V~5.5V
¾
32768
¾
Hz
¾
32768
¾
Hz
fSYS2
System Clock
(32768Hz Crystal OSC)
¾
fRTCOSC
RTC Frequency
¾
fTIMER
Timer I/P Frequency
(TMR0/TMR1)
tWDTOSC Watchdog Oscillator Period
Min.
Conditions
VDD
¾
¾
2.2V~5.5V
0
¾
4000
kHz
¾
3.3V~5.5V
0
¾
8000
kHz
3V
¾
45
90
180
ms
5V
¾
32
65
130
ms
tRES
External Reset Low Pulse Width
¾
¾
1
¾
¾
ms
tSST
System Start-up Timer Period
¾
Power-up or wake-up from
HALT
¾
1024
¾
tSYS
tINT
Interrupt Pulse Width
¾
¾
1
¾
¾
ms
tAD
A/D Clock Period
¾
¾
1
¾
¾
ms
tADC
A/D Conversion Time
¾
¾
¾
76
¾
tAD
tADCS
A/D Sampling Time
¾
¾
¾
32
¾
tAD
Note:
tSYS= 1/fSYS
Rev. 1.20
6
April 14, 2006
HT49RV5/HT49CV5
Functional Description
Execution Flow
executed and its contents specify a maximum of 4096
addresses.
The system clock is derived from either a crystal or an
RC oscillator or a 32768Hz crystal oscillator. It is internally divided into four non-overlapping clocks. One instruction cycle consists of four system clock cycles.
After accessing a program memory word to fetch an instruction code, the contents of the program counter are
incremented by one. The program counter then points to
the memory word containing the next instruction code.
Instruction fetching and execution are pipelined in such
a way that a fetch takes one instruction cycle while decoding and execution takes the next instruction cycle.
The pipelining scheme ensures that instructions are effectively executed in one cycle. Exceptions to this are instructions that change the contents of the program
counter, such as subroutine calls or jumps, in which
case, two cycles are required to complete the instruction.
When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from
subroutine, etc., the microcontroller manages program
control by loading the address corresponding to each instruction.
For conditional skip instructions, once the condition has
been met, the next instruction, which has already been
fetched during the current instruction execution, is discarded and a dummy cycle replaces it while the proper
instruction is obtained. Otherwise proceed with the next
instruction.
Program Counter - PC
The 12-bit program counter (PC) controls the sequence
in which the instructions stored in the program ROM are
S y s te m
O S C 2 (R C
C lo c k
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
o n ly )
P C
P C
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution Flow
Program Counter
Mode
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial Reset
0
0
0
0
0
0
0
0
0
0
0
0
External Interrupt 0
0
0
0
0
0
0
0
0
0
1
0
0
External Interrupt 1
0
0
0
0
0
0
0
0
1
0
0
0
Timer/Event Counter 0 Overflow
0
0
0
0
0
0
0
0
1
1
0
0
Timer/Event Counter 1 Overflow
0
0
0
0
0
0
0
1
0
0
0
0
Serial Interface Interrupt
0
0
0
0
0
0
0
1
0
1
0
0
Multi-function Interrupt
0
0
0
0
0
0
0
1
1
0
0
0
Skip
Program Counter+2
Loading PCL
*11
*10
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, Call Branch
#11
#10
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return from Subroutine
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Program Counter
Note:
*11~*0: Program counter bits
#11~#0: Instruction code bits
Rev. 1.20
S11~S0: Stack register bits
@7~@0: PCL bits
7
April 14, 2006
HT49RV5/HT49CV5
The lower byte of the program counter (PCL) is available for program control and is a readable and writeable
register (06H). Moving data into the PCL performs a
short jump. The destination will be within 256 locations.
· Location 008H
When a control transfer takes place, an additional
dummy cycle is required.
· Location 00CH
This area is reserved for the external interrupt service
program. If the INT1 input pin is activated, and the interrupt is enabled, and the stack is not full, the program will jump to this location and begin execution.
This area is reserved for the Timer/Event Counter 0 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 0 overflow, and if the interrupt is enabled and the stack is not full, the program will jump to this location and begin execution.
Program Memory - EPROM
The program memory (EPROM) is used to store the program instructions which are to be executed. It also contains data, table, and interrupt entries, and is organized
into 4096´16 bits format. The program counter is composed of 12 bits, so it can directly access the whole program memory without changing banks.
· Location 010H
This area is reserved for the Timer/Event Counter 1 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 1 overflow, and if the interrupt is enabled and the stack is not full, the program
will jump to this location and begin execution.
Certain locations in the ROM are reserved for special
usage:
· Location 014H
· Location 000H
This area is reserved for the Serial Interface interrupt
service program. If 8 bits of data have been received
or transmitted successfully from the serial interface,
and the interrupt is enabled, and the stack is not full,
the program will jump to this location and begin execution.
This area is reserved for use by the chip reset for program initialization. After a chip reset is initiated, the
program will jump to this location and begin execution.
· Location 004H
This area is reserved for the external interrupt service
program. If the INT0 input pin is activated, and the interrupt is enabled, and the stack is not full, the program will jump to this location and begin execution.
0 0 0 H
E x te r n a l In te r r u p t 0 S u b r o u tin e
0 0 8 H
0 1 0 H
This area is reserved for the multi-function interrupt. If
a real time clock interrupt occurs, or if a rising edge is
detected from the RMT input pin, or if a falling edge is
detected from the RMT input pin, or if the RMT overflow and the related interrupts are enabled, and the
stack is not full, the program will jump to this location
and begin execution.
D e v ic e In itia liz a tio n P r o g r a m
0 0 4 H
0 0 C H
· Location 018H
E x te r n a l In te r r u p t 1 S u b r o u tin e
· Table location
T im e r /E v e n t C o u n te r 0 In te r r u p t S u b r o u tin e
T im e r /E v e n t C o u n te r 1 In te r r u p t S u b r o u tin e
0 1 4 H
S e r ia l In te r fa c e In te r r u p t
0 1 8 H
Any location within the program memory can be used
as a look-up table where programmers can store fixed
data. The instructions ²TABRDC [m]² (the current
page, 1 page=256 words) and ²TABRDL [m]² (the last
page) transfer the contents of the lower-order byte to
the specified data memory, and the contents of the
higher-order byte to TBLH (Table Higher-order byte
register) (08H). Only the destination of the lower-order
byte in the table is well-defined, the other bits of the table word are all transferred to the lower portion of
TBLH. The TBLH is a read only register and the table
pointer (TBLP) is a read/write register (07H), which indicates the table location. Before accessing the table,
the location must be placed in the TBLP. All table re-
P ro g ra m
R O M
M u lti- fu n c tio n In te r r u p t
n 0 0 H
L o o k - u p T a b le ( 2 5 6 W o r d s )
n F F H
L o o k - u p T a b le ( 2 5 6 W o r d s )
F F F H
1 6 b its
N o te : n ra n g e s fro m
0 to F
Program Memory
Table Location
Instruction(s)
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P11
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note:
*11~*0: Table location bits
@7~@0: Table pointer bits
Rev. 1.20
P11~P8: Current program counter bits
8
April 14, 2006
HT49RV5/HT49CV5
0 0 H
lated instructions require two cycles to complete the
operation. These areas may function as normal program memory depending upon user¢s requirements.
Stack Register - STACK
The stack register is a special part of the memory used
to save the contents of the Program Counter. The stack
is organized into 8 levels and is neither part of the data
nor part of the program, and is neither readable nor
writeable. Its activated level is indexed by a stack
pointer (SP) and is neither readable nor writeable. At the
start of a subroutine call or an interrupt acknowledgment, the contents of the Program Counter is pushed
onto the stack. At the end of the subroutine or interrupt
routine, signaled by a return instruction (RET or RETI),
the contents of the Program Counter is restored to its
previous value from the stack. After a chip reset, the SP
will point to the top of the stack.
If the stack is full and a non-masked interrupt takes
place, the interrupt request flag is recorded but the acknowledgment is still inhibited. Once the SP is decremented (by RET or RETI), the interrupt is serviced. This
feature prevents stack overflow, allowing the programmer to use the structure easily. Likewise, if the stack is
full, and a ²CALL² is subsequently executed, a stack
overflow occurs and the first entry is lost (only the most
recent 8 return addresses are stored).
In d ir e c t A d d r e s s in g R e g is te r 0
0 1 H
M P 0
0 2 H
In d ir e c t A d d r e s s in g R e g is te r 1
0 3 H
M P 1
0 4 H
B P
0 5 H
A C C
0 6 H
P C L
0 7 H
T B L P
0 8 H
T B L H
0 9 H
R T C C
0 A H
S T A T U S
0 B H
IN T C 0
0 C H
T M R 0 H
0 D H
T M R 0 L
0 E H
T M R 0 C
0 F H
T M R 1 H
1 0 H
T M R 1 L
1 1 H
T M R 1 C
1 2 H
P A
1 3 H
P A C
1 4 H
P B
1 5 H
P B C
1 6 H
P C
1 7 H
P C C
1 8 H
P D
1 9 H
P D C
1 A H
P W M 0
1 B H
P W M 1
S p e c ia l P u r p o s e
D a ta M e m o ry
1 C H
1 D H
Data Memory - RAM
1 E H
The data memory (RAM) has a capacity of 231´8 bits,
and is divided into two functional groups, namely; special function registers (39´8 bit) and general purpose
data memory (RAM bank contains 192´8 bits) most of
which are readable/writeable, but some are read only.
The special function registers are overlapped in any
banks.
S B C R
2 0 H
S B D R
2 1 H
R M T C
2 2 H
R M T 0
2 3 H
R M T 1
2 4 H
The special function registers consist of an Indirect addressing register 0 (00H), a Memory pointer register 0
(MP0;01H), an Indirect addressing register 1 (02H), a
Memory pointer register 1 (MP1;03H), a Bank pointer
(BP;04H), an Accumulator (ACC;05H), a Program counter lower-order byte register (PCL;06H), a Table pointer
(TBLP;07H), a Table higher-order byte register
(TBLH;08H), a Real time clock control register
(RTCC;09H), a Status register (STATUS;0AH), an Interrupt control register 0 (INTC0;0BH), a Timer/Event
Counter 0 (TMR0H:0CH; TMR0L:0DH), a Timer/Event
Counter 0 control register (TMR0C;0EH), a Timer/Event
Counter 1 (TMR1H:0FH;TMR1L:10H), a Timer/Event
Counter 1 control register (TMR1C; 11H), Interrupt control register 1 (INTC1;1EH), Serial Bus control register
(SBCR;1FH), Serial Bus data register (SBDR; 20H), Remote timer control register (RMTC;21H), Remote control capture register 0 (RMT0;22H), Remote control
Rev. 1.20
IN T C 1
1 F H
2 5 H
A D R
2 6 H
A D C R
2 7 H
A C S R
2 8 H
V F D C
2 9 H
M F IS
3 0 H
3 F H
4 0 H
F F H
G e n e ra l P u rp o s e
D a ta M e m o ry
(1 9 2 B y te s )
: U n u s e d
R e a d a s "0 0 "
RAM Mapping
capture register 1 (RMT1;23H), Multi-function interrupt
status register (MFIS;29H), PWM data register
(PWM0;1AH, PWM1;1BH), the A/D result register
(ADR;25H), the A/D control register (ADCR;26H), the
A/D clock setting register (ACSR;27H), VFD control register (VFDC; 28H), I/O registers (PA;12H, PB;14H,
PC;16H, PD;18H) and I/O control registers (PAC;13H,
PBC;15H, PCC;17H, PDC;19H).
9
April 14, 2006
HT49RV5/HT49CV5
Arithmetic and Logic Unit - ALU
The remaining space before 40H is reserved for future
expanded usage and reading these locations will return
the result ²00H². The space before 40H overlaps in
each bank. The general-purpose data memory, addressed from 40H to FFH (Bank0; BP=0), is used for
data and control information under instruction commands.
This circuit performs 8-bit arithmetic and logic operations and provides the following functions:
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
· Logic operations (AND, OR, XOR, CPL)
· Rotation (RL, RR, RLC, RRC)
· Increment and Decrement (INC, DEC)
All data memory areas can handle arithmetic, logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the data
memory can be set and reset by ²SET [m].i² and ²CLR
[m].i². They are also indirectly accessible through memory pointer registers (MP0;01H/MP1;03H).
· Branch decision (SZ, SNZ, SIZ, SDZ etc.)
The ALU not only saves the results of a data operation
but also changes the status register.
Status Register - STATUS
The status register (0AH) is 8 bits wide and contains a
carry flag (C), an auxiliary carry flag (AC), a zero flag (Z),
an overflow flag (OV), a power down flag (PDF), and a
watchdog time-out flag (TO). It also records the status
information and controls the operation sequence.
Indirect Addressing Register
Location 00H and 02H are indirect addressing registers
that are not physically implemented. Any read/write operation of [00H] and [02H] accesses the RAM pointed to
by MP0 (01H) and MP1(03H), respectively. Reading location 00H or 02H indirectly returns the result 00H. Writing indirectly leads to no operation.
Except for the TO and PDF flags, bits in the status register can be altered by instructions similar to other registers. Data written into the status register does not alter
the TO or PDF flags. Operations related to the status
register, however, may yield different results from those
intended. The TO and PDF flags can only be changed
by a Watchdog Timer overflow, chip power-up, or clearing the Watchdog Timer and executing a ²HALT² instruction. The Z, OV, AC, and C flags reflect the status of
the latest operations.
The function of data movement between two indirect addressing registers is not supported. The memory pointer
registers, MP0 and MP1, are both 8-bit registers used to
access the RAM by combining corresponding indirect
addressing registers. MP0 can only be applied to data
memory, while MP1 can be applied to data memory and
VFD display memory.
On entering an interrupt sequence or executing a subroutine call, the status register will not be automatically
pushed onto the stack. If the contents of the status is important, and if the subroutine is likely to corrupt the status register, the programmer should take precautions
and save it properly.
Accumulator - ACC
The accumulator (ACC) is closely related with operations carried out by the ALU. It is mapped to location
05H of the RAM and is capable of operating with immediate data. The data movement between two data memory locations must pass through the ACC.
Bit No.
Label
Function
0
C
C is set if an operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation, otherwise C is cleared. C is also affected by a rotate through carry instruction.
1
AC
AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from
the high nibble into the low nibble in subtraction, otherwise AC is cleared.
2
Z
3
OV
OV is set if an operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa, otherwise OV is cleared.
4
PDF
PDF is cleared by either a system power-up or executing the ²CLR WDT² instruction.
PDF is set by executing the ²HALT² instruction.
5
TO
TO is cleared by a system power-up or executing the ²CLR WDT² or ²HALT² instruction.
TO is set by a WDT time-out.
6~7
¾
Unused bit, read as ²0²
Z is set if the result of an arithmetic or logic operation is zero, otherwise Z is cleared.
Status (0AH) Register
Rev. 1.20
10
April 14, 2006
HT49RV5/HT49CV5
data from a serial interface. After the interrupt is enabled, and the stack is not full, and the TRF bit is set, a
subroutine call to location 14H occurs. The related interrupt request flag (TRF) is reset and the EMI bit is cleared
to disable further maskable interrupts.
Interrupts
The HT49RV5/HT49CV5 provides two external interrupts, two internal timer/event counter interrupts, three
remote control timer interrupts, an internal real time
clock interrupt and serial interface interrupt. The interrupt control register 0 (INTC0;0BH) and interrupt control
register 1 (INTC1;1EH) both contain the interrupt control
bits that are used to set the enable/disable status and interrupt request flags.
The multi-function interrupt is initialized by setting the interrupt request flag (MFF; bit 6 of INTC1), which is
caused by a regular real time clock signal, or caused by
a rising edge of RMT, or caused by a falling edge of
RMT, or caused by an RMT overflow. After the interrupt
is enabled, and the stack is not full, and the MFF bit is
set, a subroutine call to location 18H occurs. The related
interrupt request flag (MFF) is reset and the EMI bit is
cleared to disable further maskable interrupts.
Once an interrupt subroutine is serviced, all other interrupts are blocked (by clearing the EMI bit). This scheme
may prevent any further interrupt nesting. Other interrupt requests may take place during this interval, but
only the interrupt request flag will be recorded. If another
interrupt requires servicing while the program is in the
interrupt service routine, the programmer should set the
EMI bit and the corresponding bit of the INTC0 or INTC1
to allow interrupt nesting. Once the stack is full, the interrupt request will not be acknowledged, even if the related
interrupt is enabled, until the SP is decremented. If immediate service is desired, the stack should be prevented
from becoming full.
During the execution of an interrupt subroutine, other
maskable interrupt acknowledgments are all held until
the ²RETI² instruction is executed or the EMI bit and the
related interrupt control bit are both set to 1 (if the stack
is not full). To return from the interrupt subroutine, ²RET²
or ²RETI² may be invoked. RETI sets the EMI bit and enables an interrupt service, but RET does not.
Interrupts occurring in the interval between the rising
edges of two consecutive T2 pulses are serviced on the
latter of the two T2 pulses if the corresponding interrupts
are enabled. In the case of simultaneous requests, the
following table shows the priority that is applied. These
can be masked by resetting the EMI bit.
All these interrupts can support a wake-up function. As
an interrupt is serviced, a control transfer occurs by
pushing the contents of the Program Counter onto the
stack followed by a branch to a subroutine at the specified location in the ROM. Only the contents of the Program Counter is pushed onto the stack. If the contents of
the register or of the status register (STATUS) is altered
by the interrupt service program which corrupts the desired control sequence, the contents should be saved in
advance.
Interrupt Source
External interrupts are triggered by an edge transition of
INT0 or INT1 (configuration option: high to low, low to
high, low to high or high to low), and the related interrupt
request flag (EIF0; bit 4 of INTC0, EIF1; bit 5 of INTC0)
is set as well. After the interrupt is enabled, the stack is
not full, and the external interrupt is active, a subroutine
call to location 04H or 08H occurs. The interrupt request
flag (EIF0 or EIF1) and EMI bits are all cleared to disable
other maskable interrupts.
Vector
External interrupt 0
1
04H
External interrupt 1
2
08H
Timer/Event Counter 0 overflow
3
0CH
Timer/Event Counter 1 overflow
4
10H
Serial Interface interrupt
5
14H
Multi-function interrupt
6
18H
The RMT overflow interrupt flag (RMTVF; bit 0 of MFIS),
real time clock interrupt flag (RTF; bit 1 of MFIS), the
RMT rising edge interrupt flag (RMT0F; bit 2 of MFIS)
and the RMT falling edge interrupt flag (RMT1F; bit 3 of
MFIS) indicate that a related interrupt has occurred. After reading these flags, these flags will not be cleared
automatically, they should be cleared by the user.
The internal Timer/Event Counter 0 interrupt is initialized by setting the Timer/Event Counter 0 interrupt request flag (T0F; bit 6 of INTC0), which is normally
caused by a timer overflow. After the interrupt is enabled, and the stack is not full, and the T0F bit is set, a
subroutine call to location 0CH occurs. The related interrupt request flag (T0F) is reset, and the EMI bit is
cleared to disable other maskable interrupts.
Timer/Event Counter 1 is operated in the same manner
but its related interrupt request flag is T1F (bit 4 of
INTC1) and its subroutine call location is 10H.
The serial interface interrupt is indicated by the interrupt
flag (TRF; bit 5 of INTC1), that is caused by receiving or
transferring a complete 8-bit data transfer between the
HT49RV5/ HT49CV5 and an external device. After the
interrupt is enabled (by setting ESBI; bit 1 of INTC1),
and the stack is not full, a subroutine call to location 14H
occurs. TRF is set by SIO and should be cleared by users.
The Serial Interface interrupt is initialized by setting the
interrupt request flag (TRF; bit 5 of INTC1), which is
caused by completely receiving or transferring 8 bits of
Rev. 1.20
Priority
The Timer/Event Counter 0 interrupt request flag (T0F),
external interrupt 1 request flag (EIF1), external interrupt 0 request flag (EIF0), enable Timer/Event Counter0
11
April 14, 2006
HT49RV5/HT49CV5
Bit No.
Label
0
EMI
Control the master (global) interrupt (1=enabled; 0=disabled)
Function
1
EEI0
Control the external interrupt 0 (1=enabled; 0=disabled)
2
EEI1
Control the external interrupt 1 (1=enabled; 0=disabled)
3
ET0I
Control the Timer/Event Counter 0 interrupt (1=enabled; 0=disabled)
4
EIF0
External interrupt 0 request flag (1=active; 0=inactive)
5
EIF1
External interrupt 1 request flag (1=active; 0=inactive)
6
T0F
Internal Timer/Event Counter 0 request flag (1=active; 0=inactive)
7
¾
For test mode used only.
Must be written as ²0²; otherwise may result in unpredictable operation.
INTC0 (0BH) Register
Bit No.
Label
0
ET1I
Control the Timer/Event Counter 1 interrupt (1=enabled; 0=disabled)
Function
1
ESBI
Control the serial interface interrupt (1=enabled; 0=disabled)
2
EMFI
3, 7
¾
Control the real multi-function interrupt (1=enabled; 0=disabled)
Unused bit, read as ²0²
4
T1F
Internal Timer/Event Counter 1 request flag (1=active; 0=inactive)
5
TRF
Serial bus data transferred or data received interrupt request flag (1=active; 0=inactive)
6
MFF
Multi-function interrupt request flag (1=active; 0=inactive)
INTC1 (1EH) Register
Bit No.
Label
0
¾
1
ERMT0
2
ERMT1
Controls the remote control timer falling edge interrupt (1=enable; 0=disable)
3
ERMTV
Controls the remote control timer overflow interrupt (1=enable; 0=disable)
4
RME
5
RMCS
Selects the remote control timer clock source fX (1=fSYS; 0=fSYS/4)
RMS0
RMS1
Selects the remote control timer clock
00=fX/25
01= fX/26
10= fX/27
11= fX/28
6
7
Function
Unused bit, read as ²0²
Controls the remote control timer rising edge interrupt (1=enable; 0=disable)
Controls the remote control timer (1=enable; 0=disable)
1=enable & start counting; 0= disable & clear counter to 0
RMTC (21H) Register
Bit No.
Label
Function
Remote control timer overflow interrupt flag (1=indicates that an overflow has occurred;
0=indicates that an overflow has not occurred)
0
RMTVF
1
RTF
2
RMT0F
Remote control timer rising edge interrupt flag (1=indicates that a rising edge interrupt has
occurred; 0=indicates that a rising edge interrupt has not occurred)
3
RMT1F
Remote control timer falling edge interrupt flag (1=indicates that a falling edge interrupt has
occurred; 0=indicates that a falling edge interrupt has not occurred)
4
ERTI
5~7
¾
Real time clock interrupt flag (1=indicates that an RTC interrupt has occurred;
0=indicates that an RTC interrupt has not occurred)
Controls the real time clock interrupt (1=enable; 0=disable)
Unused bit, read as ²0²
MFIS (29H) Register
Rev. 1.20
12
April 14, 2006
HT49RV5/HT49CV5
interrupt bit (ET0I), enable external interrupt 1 bit (EEI1),
enable external interrupt 0 bit (EEI0), and enable master
interrupt bit (EMI) constitute the Interrupt Control register 0 (INTC0) which is located at 0BH in the RAM.
signal is used for the system clock. The HALT mode
stops the system oscillator (RC and crystal oscillator
only) and ignores external signals so as to conserve
power. The 32768Hz crystal oscillator still runs in the
HALT mode. If the 32768Hz crystal oscillator is selected
as the system oscillator, the system oscillator is not
stopped but the instruction execution is stopped. Since
the 32768Hz oscillator is also designed for timing purposes, the internal timing (RTC, WDT) operation still
runs even if the system enters the HALT mode.
The multi-function interrupt request flag (MFF), serial interface interrupt request flag (TRF), Timer/Event Counter 1 interrupt request flag (T1F), enable multi-function
interrupt (EMFI), enable serial interface interrupt bit
(ESBI), and enable Timer/Event Counter 1 interrupt bit
(ET1I), constitute the Interrupt Control register 1
(INTC1) which is located at 1EH in the RAM.
Of the three oscillators, if the RC oscillator is used, an
external resistor between OSC1 and VSS is required,
and the range of the resistance should be from 56kW to
1.5MW. The system clock, divided by 4, is available on
OSC2 with pull-high resistor, which can be used to synchronize external logic. The RC oscillator provides the
most cost effective solution. However, the frequency of
the oscillation may vary with VDD, temperature, and the
chip itself due to process variations. It is therefore not
suitable for timing sensitive operations where accurate
oscillator frequency is desired.
The enable Remote control timer rising edge interrupt
(ERMT0), enable Remote control timer falling edge interrupt (ERMT1), enable Remote control timer overflow
interrupt (ERMTV), enable Remote control timer start
counting (RME), select the Remote control timer clock
source (RMCS), and select the Remote control timer
clock (RMS0, RMS1) constitute the Remote Timer control Register (RMTC) which is located at 21H in the
RAM.
E M I , EE I 0, E E I 1, E T0I , E T1I , S B E N , E RT I ,
EMFI,ERMT0 and ERMT1 are all used to control the enable/disable status of interrupts. These bits prevent the
requested interrupt from being serviced. Once the interrupt request flags (MFF, TRF, T0F, T1F, EIF1, EIF0) are
all set, they remain in the INTC0~INTC1 respectively
until the interrupts are serviced or cleared by a software
instruction.
On the other hand, if the crystal oscillator is selected, a
crystal across OSC1 and OSC2 is needed to provide the
feedback and phase shift for the oscillator, and no other
external components are required. A resonator may be
connected between OSC1 and OSC2 to replace the
crystal and to get a frequency reference, but two external capacitors on OSC1 and OSC2 are required.
There is another oscillator circuit designed for the real
time clock. In this case, only a 32768Hz crystal oscillator
can be applied. The crystal should be connected between OSC3 and OSC4.
It is recommended that a program should not use the
²CALL subroutine² within the interrupt subroutine. This
is because interrupts often occur in an unpredictable
manner or require to be serviced immediately in some
applications. During that period, if only one stack is left,
and enabling the interrupt is not well controlled, operation of the ²CALL² in the interrupt subroutine may damage the original control sequence.
The RTC oscillator circuit can be controlled to start-up
quickly by setting the ²QOSC² bit (bit 4 of RTCC). It is
recommended to turn on the quick start-up function
during power-on, and then turn it off after 2 seconds.
The WDT oscillator is a free running on-chip RC oscillator and no external components are required. Although
the system enters the power down mode, the system
clock stops and the WDT oscillator still works with a period of approximately 65ms at 5V. The WDT oscillator
can be disabled by options so as to conserve power.
Oscillator Configuration
The HT49RV5/HT49CV5 provides three oscillator circuits for system clocks, i.e., RC oscillator, crystal oscillator and 32768Hz crystal oscillator, determined by
options. No matter what type of oscillator is selected, the
O S C 3
O S C 1
O S C 4
O S C 2
3 2 7 6 8 H z C r y s ta l/R T C O s c illa to r
O S C 1
fS
Y S
/4
C r y s ta l O s c illa to r
O S C 2
R C
O s c illa to r
System Oscillator
Note:
32768Hz crystal enable condition: For WDT clock source or for system clock source.
The external resistor and capacitor components connected to the 32768Hz crystal are not necessary to provide oscillation. For applications where precise RTC frequencies are essential, these components may be required to provide frequency compensation due to different crystal manufacturing tolerances.
Rev. 1.20
13
April 14, 2006
HT49RV5/HT49CV5
Watchdog Timer - WDT
Multi-function Timer
The WDT clock source is implemented by a dedicated
RC oscillator (WDT oscillator) or an instruction clock
(system clock/4) or a real time clock oscillator (RTC oscillator). The timer is designed to prevent a software
malfunction or sequence from jumping to an unknown
location with unpredictable results. The WDT can be
disabled by options. But if the WDT is disabled, all executions related to the WDT lead to no operation.
The HT49RV5/HT49CV5 provides a multi-function timer
for the and RTC but with different time-out periods. The
multi-function timer consists of an 8-stage divider and a
7-bit prescaler, with the clock source coming from the
RTC OSC or the instruction clock (i.e., system clock divided by 4). The multi-function timer also provides a
selectable frequency signal (ranging from fS/20 to fS/27)
for the VFD driver circuits, and a selectable frequency
signal (ranging from fS/21 to fS/28) for the buzzer output
by options. It is recommended to select a frequency as
close as possible to 32kHz for the VFD driver circuits to
obtain good display clarity.
Once an internal WDT oscillator (RC oscillator with a period of 65ms at 5V) is selected, it is divided by 212~215
(by configuration option to get the WDT time-out period).
The minimum WDT time-out period is 300ms~600ms.
This time-out period may vary with temperature, VDD
and process variations. By selecting the WDT configuration option, longer time-out periods can be realized. If
the WDT time-out is selected, 215, the maximum
time-out period is divided by 215~216 which is 2.3s~4.7s.
If the WDT oscillator is disabled, the WDT clock may still
come from the instruction clock and operates in the
same manner except that in the halt state the WDT may
stop counting and lose its protecting purposes. In this
situation the logic can only be restarted by external
logic. If the device operates in a noisy environment, using the on-chip RC oscillator (WDT OSC) is strongly recommended since the HALT will stop the system clock.
fS
R O M
C lo c k /4
R T C
O S C 3 2 7 6 8 H z
C o n fig u r a tio n
O p tio n
C o d e O p tio n
V F D D r iv e r ( fS /2 0 ~ fS /2 7 )
B u z z e r (fS /2 1~ fS /2 8)
Real Time Clock - RTC
The real time clock (RTC) is used to supply a regular internal interrupt. Its time-out period ranges from fS/28 to
fS/215 by software programming. Writing data to RT2,
RT1 and RT0 (bits 2, 1, 0 of RTCC; 09H) yields various
time-out periods. If the RTC time-out occurs and the interrupt is enabled, the related interrupt request flag
(RTF; bit 1 of MFIS) is set and the multi-function interrupt request flag (MFF; bit 6 of INTC1) is set. If the interrupt (EMFI) is enabled, and the stack is not full, a
subroutine call to location 18H occurs.
The WDT overflow under normal operation initializes a
²chip reset² and sets the status bit ²TO². In the HALT
mode, the overflow initializes a ²warm reset², and only
the Program Counter and SP are reset to zero. To clear
the contents of the WDT, there are three methods to be
adopted, i.e., external reset (a low level to RES), software instruction, and a ²HALT² instruction. There are
two types of software instructions; ²CLR WDT² and the
other set - ²CLR WDT1² and ²CLR WDT2². Of these
two types of instruction, only one type of instruction can
be active at a time depending on the options - ²CLR
WDT² times selection option. If the ²CLR WDT² is selected (i.e., CLR WDT times is equal to one), any execution of the ²CLR WDT² instruction clears the WDT. In the
case where the two ²CLR WDT1² and ²CLR WDT2² instructions are chosen (i.e., CLR WDT times is equal to
two), these two instructions have to be executed to clear
the WDT, otherwise, the WDT may reset the chip due to
time-out.
S y s te m
D iv id e r
RT2
RT1
RT0
RTC Clock Divided Factor
0
0
0
2 8*
0
0
1
2 9*
0
1
0
210*
0
1
1
211*
1
0
0
212
1
0
1
213
1
1
0
214
1
1
1
215
Note: * not recommended to be used
fS
C o n fig u r a tio n
O p tio n
fW
fW
D T
D T
/2
D iv id e r
W D T
1 2 k H z
O S C
8
W D T
P r e s c a le r
M a s k O p tio n
W D T C le a r
C K
T
R
C K
T
R
T im e - o u t
fW D T /2 15~
fW D T /2 14~
fW D T /2 13~
fW D T /2 12~
R e s e t
fW D T /2 1
fW D T /2 1
fW D T /2 1
fW D T /2 1
6
5
4
3
Watchdog Timer
Rev. 1.20
14
April 14, 2006
HT49RV5/HT49CV5
fS
D iv id e r
P r e s c a le r
R T 2
R T 1
R T 0
8 to 1
M u x .
fS /2 8~ fS /2 15
R T C In te rru p t
Real Time Clock
The RTCC register descriptions are listed below.
Bit No.
Label
Read/
Write
Reset
Function
0~2
RT0~RT2
R/W
1
8 to 1 multiplexer control inputs to select the real clock prescaler output
3, 5~7
¾
¾
¾
Unused bit, read as ²0²
4
QOSC
R/W
0
32768Hz OSC quick start-up oscillator
0/1: quick/slow start
RTCC (09H) Register
Power Down Operation - HALT
interrupt is enabled and the stack is not full, the regular
interrupt response takes place.
The HALT mode is initialized by the ²HALT² instruction
and results in the following.
If an interrupt request flag is set to ²1² before entering
the ²HALT² mode, the wake-up function of the related interrupt will be disabled.
· The system oscillator turns off but the WDT oscillator
keeps running (if the WDT oscillator or the real time
clock is selected).
If a wake-up event occurs, it takes 1024 tSYS (system
clock period) to resume normal operation. In other
words, a dummy period will be inserted after a wake-up.
If the wake-up results from an interrupt acknowledge
signal, the actual interrupt subroutine execution will be
delayed by one or more cycles. However, if the wake-up
results in the next instruction execution, this will be executed immediately after the dummy period is finished.
· The contents of the on-chip RAM and of the registers
remain unchanged.
· The WDT is cleared and starts recounting (if the WDT
clock source is from the WDT oscillator or the real time
clock oscillator).
· All I/O ports maintain their original status.
· The PDF flag is set but the TO flag is cleared.
· The VFD driver keeps running (if the RTC OSC is se-
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT mode.
lected).
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge signal on port A, an external rising/falling edge on the RMT
pin, or a WDT overflow. An external reset will initialize a
chip reset and a WDT overflow will initialize a ²warm reset². After examining the TO and PDF flags, the source
of the reset can be determined. The PDF flag is cleared
by a system power-up or by executing the ²CLR WDT²
instruction, and is set by executing the ²HALT² instruction. The TO flag is set if a WDT time-out occurs, and
causes a wake-up that only resets the Program Counter
and SP, the other flags remain in their original status.
Reset
There are three ways in which a microcontroller reset
can occur, through events occurring both internally and
externally:
· RES is reset during normal operation
· RES is reset during HALT
· WDT time-out is reset during normal operation
The WDT time-out reset during HALT is a little different
from other kinds of reset. Most of the conditions remain
unchanged except that the program counter and stack
pointer will be cleared to 0 and the TO flag will be set to
1. Most registers are reset to the ²initial condition² once
the reset conditions are met.
The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each bit
in port A can be independently selected to wake up the
device by options. Awakening from an I/O port stimulus,
the program will resume execution at the next instruction. If the system is woken up via an interrupt, two possibilities may occur. If the related interrupt is disabled or
the interrupt is enabled but the stack is full, the program
will resume execution at the next instruction. But if the
Rev. 1.20
The different types of resets described affect the reset
flags in different ways. These flags, the PDF and TO
flags, are located in the status register and are controlled by various microcontroller operations such as the
HALT function or Watchdog Timer.
15
April 14, 2006
HT49RV5/HT49CV5
V
The reset flags are shown in the table:
TO
PDF
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES Wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT Wake-up HALT
D D
0 .0 1 m F *
RESET Conditions
1 0 0 k W
R E S
1 0 k W
0 .1 m F *
Reset Circuit
Note: ²u² stands for unchanged
Note:
To ensure that the system oscillator is started and stabilized, the SST (System Start-up Timer) provides an extra delay of 1024 system clock pulses when the system
awakes from the HALT state or during power-on.
V D D
An extra SST delay is added during the power-on period, and any wake-up from HALT may enable only the
SST delay.
R E S
000H
Interrupt
Disabled
Prescaler, Divider
Cleared
WDT
Clear. After master reset,
WDT begins counting
tS
S T
S S T T im e - o u t
The functional unit chip reset status is shown below.
Program Counter
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to
avoid noise interference.
C h ip
R e s e t
Reset Timing Chart
H A L T
W D T
W a rm
W D T
T im e - o u t
R e s e t
E x te rn a l
R E S
Timer/Event Counter Off
Input/Output Ports
Input mode
Stack Pointer
Points to the top of the stack
R e s e t
C o ld
R e s e t
S S T
1 0 - b it R ip p le
C o u n te r
O S C 1
P o w e r - o n D e te c tio n
Reset Configuration
The register states are summarized below:
Register
Reset
(Power-on)
WDT Time-out
RES Reset
(Normal Operation) (Normal Operation)
RES Reset
(HALT)
WDT Time-out
(HALT)*
TMR0H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0L
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0C
00-0 1000
00-0 1000
00-0 1000
00-0 1000
uu-u uuuu
TMR1H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1L
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1C
0000 1---
0000 1---
0000 1---
0000 1---
uuuu u---
Program
Counter
0000H
0000H
0000H
0000H
0000H
MP0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
BP
--0- -000
--0- -000
--0- -000
--0- -000
--u- -uuu
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
STATUS
--00 xxxx
--1u uuuu
--uu uuuu
--01 uuuu
--11 uuuu
Rev. 1.20
16
April 14, 2006
HT49RV5/HT49CV5
Register
INTC0
Reset
(Power-on)
WDT Time-out
RES Reset
(Normal Operation) (Normal Operation)
-000 0000
-000 0000
-000 0000
RES Reset
(HALT)
WDT Time-out
(HALT)*
-000 0000
-uuu uuuu
INTC1
-000 -000
-000 -000
-000 -000
-000 -000
-uuu -uuu
RMTC
0000 000-
0000 000-
0000 000-
0000 000-
uuuu uuu-
MFIS
---0 0000
---0 0000
---0 0000
---0 0000
---u uuuu
RTCC
---0 -111
---0 -111
---0 -111
---0 -111
---u -uuu
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
---- 1111
---- 1111
---- 1111
---- 1111
---- uuuu
PBC
---- 1111
---- 1111
---- 1111
---- 1111
---- uuuu
PC
11-- ----
11-- ----
11-- ----
11-- ----
uu-- ----
PCC
11-- ----
11-- ----
11-- ----
11-- ----
uu-- ----
PD
1111 --11
1111 --11
1111 --11
1111 --11
uuuu --uu
PDC
1111 --11
1111 --11
1111 --11
1111 --11
uuuu --uu
PWM0
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
PWM1
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
SBCR
0110 0000
0110 0000
0110 0000
0110 0000
uuuu uuuu
SBDR
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
RMT0
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
RMT1
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
ADR
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
ADCR
01-0 0-00
01-0 0-00
01-0 0-00
01-0 0-00
uu-u u-uu
ACSR
1--- --00
1--- --00
1--- --00
---- --00
u--- --uu
VFDC
0000 -111
0000 -111
0000 -111
0000 -111
0000 -111
Note:
²*² stands for ²warm reset²
²u² stands for ²unchanged²
²x² stands for ²unknown²
Timer/Event Counter
and the contents of the lower-order byte buffer to
TMR0H (TMR1H) and TMR0L (TMR1L) registers, respectively. The Timer/Event Counter 1/0 preload register is changed by each writing TMR0H (TMR1H)
operations. Reading TMR0H (TMR1H) will latch the
contents of TMR0H (TMR1H) and TMR0L (TMR1L)
counters to the destination and the lower-order byte
buffer, respectively. Reading the TMR0L (TMR1L) will
read the contents of the lower-order byte buffer. The
TMR0C (TMR1C) is the Timer/Event Counter 0 (1) control register, which defines the operating mode, counting
enable or disable and an active edge.
Two timer/event counters (TMR0,TMR1) are implemented in the microcontroller. The Timer/Event Counter
0 contains a 16-bit programmable count-up counter and
the clock may come from an external source or an internal clock source. An internal clock source comes from
fSYS. The Timer/Event Counter 1 contains a 16-bit programmable count-up counter and the clock may come
from an external source or an internal clock source. An
internal clock source comes from fSYS/4 or 32768Hz selected by option. The external clock input allows the
user to count external events, measure time intervals or
pulse widths, or to generate an accurate time base.
The TM0 and TM1 bits define the operation mode. The
event count mode is used to count external events,
which means that the clock source is from an external
(TMR0, TMR1) pin. The timer mode functions as a normal timer with the clock source coming from the internal
selected clock source. Finally, the pulse width measurement mode can be used to count the high or low level
duration of the external signal (TMR0, TMR1), and the
counting is based on the internal selected clock source.
There are six registers related to the Timer/Event Counter 0 and Timer/Event Counter 1; TMR0H (0CH),
TMR0L (0DH), TMR0C (0EH) and the Timer/Event
Counter 1, TMR1H (0FH), TMR1L (10H), and TMR1C
(11H). Writing TMR0L (TMR1L) will only place the written data to an internal lower-order byte buffer (8-bit) and
writing TMR0H (TMR1H) will transfer the specified data
Rev. 1.20
17
April 14, 2006
HT49RV5/HT49CV5
The measured result remains in the timer/event counter
even if the activated transient occurs again. In other
words, only 1-cycle measurement can be made until the
TON bit is set. The cycle measurement will continue as
long as it receives further transient pulse. In this operation mode, the timer/event counter begins counting not
according to the logic level but to the transient edges. In
the case of counter overflows, the counter is reloaded
from the timer/event counter register and issues an interrupt request, as in the other two modes, i.e., the event
and timer modes.
In the event count or timer mode, the timer/event counter starts counting at the current contents in the
timer/event counter and ends at FFFFH. Once an overflow occurs, the counter is reloaded from the timer/event
counter preload register, and generates an interrupt request flag (T0F; bit 6 of INTC0, T1F; bit 4 of INTC1). In
the pulse width measurement mode with the values of
the TON and TE bits equal to 1, after the TMR0 (TMR1)
has received a transient from low to high (or high to low if
the TE bit is ²0²), it will start counting until the TMR0
(TMR1) returns to the original level and resets the TON.
Bit No.
0~2
Label
3
T0E
4
T0ON
5
¾
6
7
Function
Defines the prescaler stages.
T0PSC2, T0PSC1, T0PSC0=
000: fINT=fSYS
001: fINT=fSYS/2
T0PSC0~ 010: fINT=fSYS/4
T0PSC2 011: fINT=fSYS/8
100: fINT=fSYS/16
101: fINT=fSYS/32
110: fINT=fSYS/64
111: fINT=fSYS/128
T0M0
T0M1
Defines the TMR0 active edge of the timer/event counter:
In Event Counter Mode (T0M1,T0M0)=(0,1):
1:count on falling edge;
0:count on rising edge
In Pulse Width measurement mode (T0M1,T0M0)=(1,1):
1: start counting on the rising edge, stop on the falling edge;
0: start counting on the falling edge, stop on the rising edge
Enable/disable timer counting (0=disable; 1=enable)
Unused bit, read as ²0²
Defines the operating mode (T0M1, T0M0)
01= Event count mode (External clock)
10= Timer mode (Internal clock)
11= Pulse Width measurement mode (External clock)
00= Unused
TMR0C (0EH) Register
Bit No.
Label
0~2
¾
3
T1E
4
T1ON
5
T1S
6
7
T1M0
T1M1
Function
Unused bit, read as ²0²
Defines the TMR1 active edge of the timer/event counter:
In Event Counter Mode (T1M1,T1M0)=(0,1):
1:count on falling edge;
0:count on rising edge
In Pulse Width measurement mode (T1M1,T1M0)=(1,1):
1: start counting on the rising edge, stop on the falling edge;
0: start counting on the falling edge, stop on the rising edge
Enable/disable timer counting (0= disable; 1= enable)
Defines the TMR1 internal clock source (0=fSYS/4; 1=32768Hz)
Defines the operating mode (T1M1, T1M0)
01= Event count mode (External clock)
10= Timer mode (Internal clock)
11= Pulse Width measurement mode (External clock)
00= Unused
TMR1C (11H) Register
Rev. 1.20
18
April 14, 2006
HT49RV5/HT49CV5
When the timer/event counter (reading TMR0/TMR1) is
read, the clock is blocked to avoid errors, as this may results in a counting error. Blocking of the clock should be
taken into account by the programmer. It is strongly recommended to load a desired value into the TMR0/TMR1
register first, before turning on the related timer/event
counter, for proper operation since the initial value of the
TMR0/TMR1 is unknown. Due to the timer/event counter scheme, the programmer should pay special attention on the instruction to enable then disable the timer
for the first time, whenever there is a need to use the
timer/event counter function, to avoid unpredictable result. After this procedure, the timer/event function can
be operated normally.
To enable the counting operation, the Timer on bit (TON;
bit 4 of TMR0C or TMR1C) should be set to 1. In the
pulse width measurement mode, TON is automatically
cleared after the measurement cycle is completed. But
in the other two modes, TON can only be reset by instructions. The overflow of the Timer/Event Counter 0/1
is one of the wake-up sources and can also be applied
to a PFD (Programmable Frequency Divider) output at
PA3 by options. Only one PFD (PFD0 or PFD1) can be
applied to PA3 by options. No matter what the operation
mode is, writing a 0 to ET0I or ET1I disables the related
interrupt service. When the PFD function is selected, executing ²SET [PA].3² instruction will enable the PFD output and executing ²CLR [PA].3² instruction will disable
the PFD output.
Bits 2~0 of the TMR0C can be used to define the
pre-scaling stages of the internal clock sources of the
timer/event counter. The definitions are as shown. The
overflow signal of the timer/event counter can be used
to generate the PFD signal. The timer prescaler is also
used as the PWM counter.
In the case of timer/event counter OFF condition, writing
data to the timer/event counter preload register also reloads that data to the timer/event counter. But if the
timer/event counter is turned on, data written to the
timer/event counter is kept only in the timer/event counter preload register. The timer/event counter still continues its operation until an overflow occurs.
P W M
(6 + 2 ) o r (7 + 1 )
C o m p a re
fS
T o P D 0 /P D 1
8 - s ta g e P r e s c a le r
Y S
f IN
8 -1 M U X
T 0 P S C 2 ~ T 0 P S C 0
D a ta B u s
T
T 0 M 1
T 0 M 0
T M R 0
R e lo a d
1 6 - b it T im e r /E v e n t C o u n te r
P r e lo a d R e g is te r
T 0 E
T 0 M 1
T 0 M 0
T 0 O N
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
O v e r flo w
to In te rru p t
1 6 - b it T im e r /E v e n t C o u n te r
(T M R 0 H /T M R 0 L )
T
Q
P F D 0
P A 3 D a ta C T R L
Timer/Event Counter 0
fS
Y S
/4
3 2 7 6 8 H z
T 1 S
M
U
f IN
D a ta B u s
T
X
T 1 M 1
T 1 M 0
T M R 1
1 6 - b it T im e r /E v e n t C o u n te r R e lo a d
P r e lo a d R e g is te r
T 1 E
T 1 M 1
T 1 M 0
T 1 O N
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
O v e r flo w
to In te rru p t
1 6 - b it T im e r /E v e n t C o u n te r
(T M R 1 H /T M R 1 L )
T
Q
P F D 1
P A 3 D a ta C T R L
Timer/Event Counter 1
Rev. 1.20
19
April 14, 2006
HT49RV5/HT49CV5
Remote Control Timer - RMT
The RMT pin with rising/falling edge wake-up function,
8-bit timer counter will be cleared during a chip reset.
The HT49RV5/HT49CV5 provides an 8-bit remote control timer that has a pulse width measurement function.
Pulse width is measured from a difference in count value
when the valid edge (RMT pin) has been detected while
the timer operates in the running mode.
And the RMT clock starts to count after the rising/falling
edge trigger.
In te rru p t (R M T 0 F )
N o is e R e je c tio n
R is in g E d g e
D e te c tio n
R M T
fS
fS
Y S
Y S
/4
M
U
fX
X
R M C S
L a tc h
R e m o te C o n tr o l T im e r
C a p tu r e R e g is te r
R M T 0 (2 2 H )
fX /2 5~ fX /2 8
P r e - s c a le r
O v e r flo w
4 -1 M U X
R M S 1 R M S 0
(R M T V F )
8 - b it T im e r C o u n te r
C le a r
R M E
N o is e R e je c tio n
F a llin g E d g e
D e te c tio n
L a tc h
R e m o te C o n tr o l T im e r
C a p tu r e R e g is te r
R M T 1 (2 3 H )
In te rru p t (R M T 1 F )
Remote Control Timer
Bit No.
Label
0
¾
1
ERMT0
Function
Unused bit, read as ²0²
Controls the remote control timer rising edge interrupt (1=enable; 0=disable)
2
ERMT1
Controls the remote control timer falling edge interrupt (1=enable; 0=disable)
3
ERMTV
Controls the remote control timer overflow interrupt (1=enable; 0=disable)
4
RME
5
RMCS
Selects the remote control timer clock source fX (1=fSYS; 0=fSYS/4)
RMS0
RMS1
Selects the remote control timer clock
00=fX/25
01= fX/26
10= fX/27
11= fX/28
6~7
Controls the remote control timer (1=enable & start count; 0=disable & clear counter)
RMTC (21H) Register
Bit No.
Label
Function
0
RMTVF
1
RTF
2
RMT0F
Remote control timer rising edge interrupt flag (1=indicates that a rising edge interrupt has
occurred; 0=indicates that a rising edge interrupt has not occurred)
3
RMT1F
Remote control timer falling edge interrupt flag (1=indicates that a falling edge interrupt has
occurred; 0=indicates that a falling edge interrupt has not occurred)
4
ERTI
5~7
¾
Remote control timer overflow interrupt flag (1=indicates that an overflow has occurred;
0=indicates that an overflow has not occurred)
Real time clock interrupt flag (1=indicates that an RTC interrupt has occurred;
0=indicates that an RTC interrupt has not occurred)
Controls the real time clock interrupt (1=enable; 0=disable)
Unused bit, read as ²0²
MFIS (29H) Register
Rev. 1.20
20
April 14, 2006
HT49RV5/HT49CV5
Serial Interface
The Serial Interface function has four basic signals included. They are the SDI (serial data input), SDO (serial data output), SCK (serial clock) and SCS (slave select pin).
Two registers (SBCR & SBDR) unique to the serial interface provide control, status and data storage.
S B E N = 1 , C S E N = 0 ( if p u ll- h ig h e d )
S C S
S B E N = C S E N = 1
S C K
S D I
S D O
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
SIO Timing (SIOCLK Configuration is Falling Edge)
S B E N = 1 , C S E N = 0 ( if p u ll- h ig h e d )
S C S
S B E N = C S E N = 1
S C K
S D I
S D O
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
SIO Timing (SIOCLK Configuration is Rising Edge)
Bit No.
Label
0
¾
1
WCOL
2
CSEN
3
MLS
4
SBEN
5, 6
M0, M1
7
CKS
Function
Unused bit, read as ²0²
This bit shows the situation of the buffer SBDR
1: enable (set by SIO) writing to SBDR
0: disable (cleared by user) reading from SBDR
Serial bus selection signal
Shift first control bit (1: MSB; 0: LSB)
Serial bus selection (1: enable; 0: disable)
Master/slave mode selection: M1, M0=
00: master mode, baud rate=fSIO
01: master mode, baud rate=fSIO/4
10: master mode, baud rate=fSIO/16
11: slave mode
Clock source selection (0: fSYS/4; 1: fRTCOSC)
SBCR (1FH) Register
· SBCR: Serial bus control register
¨
¨
¨
Bit 7 (CKS): clock source selection:
fSIO=fSYS/4 or fRTCOSC
Master mode: write data to SBDR (TXRX buffer)
® start transmission/reception automatically
M1, M0:
Master mode: when data has been transferred ®
set TRF
00: master mode, baud rate=fSIO
01: master mode, baud rate=fSIO/4
Slave mode: when a SCK (and SCS dependent
on CSEN) is received, data in TXRX buffer is
shifted-out and data on SDI is shifted-in
10: master mode, baud rate=fSIO/16
11: slave mode
Rev. 1.20
Enable: (SCS dependent on CSEN bit)
Disable ® enable: SCK, SDI, SDO, SCS=0 and
waiting for writing data to SBDR (TXRX buffer)
Bit 6 (M1), Bit 5 (M0): master/slave mode & baud
rate selection
-
Bit 4 (SBEN): serial bus enable/disable (1/0)
-
21
April 14, 2006
HT49RV5/HT49CV5
-
Disable: SCK, SDI, SCS floating, SDO output
high
¨
Bit 3 (MLS): MSB or LSB (1/0) shift first control bit
¨
Bit 2 (CSEN): serial bus selection signal enable/disable (SCS), when CSEN=0, SCS is floating
¨
¨
Clock Polarity=Rising Edge or Falling Edge
(Configuration Option)
· Serial interface operation
¨
Master mode operation
Step1: Select CKS and select M1, M0 = 00, 01, 10
Bit 1 (WCOL): this bit is set to 1 if data is written to
SBDR (TXRX buffer) when data is transferred ®
writing will be ignored if data is written to SBDR
(TXRX buffer) when data is transferred
Step2: Select CSEN, MLS (the same as the slave)
Step3: Set SBEN
Step4: Writing data to SBDR
Bit 0 (TRF): data transferred or data received ®
used to generate interrupt
Note: data receiving is still working when the MCU
enters the HALT mode
-
data is stored in TXRX buffer
-
output SCK and SCS signals
-
go to step 5
Note: SIO internal operation:
* data stored in TXRX buffer, and SDI data
is shifted into TXRX buffer
* data transferred, data in TXRX buffer is
latched into SBDR
· SBDR: Serial bus data register
¨
Data written to SBDR ® write data to TXRX buffer
only
¨
Data read from SBDR ® read from SBDR only
¨
Step5: Check WCOL
Operating Mode description
-
Master transmitter: clock sending and data I/O
started by writing SBDR
-
WCOL= 1, clear WCOL and go to step 4
-
WCOL= 0, go to step 6
Step6: Check TRFor waiting for serial bus interrupt
-
Master clock sending started by writing SBDR
Step7: Read data from SBDR
-
Slave transmitter: data I/O started by clock received
Step8: Clear TRF
-
Slave receiver: data I/O started by clock received
Step9: Go to step 4
D a ta B u s
S B D R
( R e c e iv e d D a ta R e g is te r )
M
D 7 D 6 D 5 D 4 D 3 D 2 D 1 D 0
U
S D O
X
M L S
A N D , S ta rt
E N
S C K
A N D , S ta rt
C lo c k P o la r ity
S B E N
M
U
X
C 0
C 1
X
S D I
C 2
T D R F
W C O L F la g
In te r n a l B u s y F la g
W r ite S B D R
S B E N
A N D , S ta rt
E N
C S E N
U
A N D
M a s te r
o r
S la v e
S D O
S B E N
M
In te r n a l B a u d R a te C lo c k
B u ffe r
S B E N
W r ite S B D R E n a b le /D is a b le
W r ite S B D R
S C S
M a s te r o r S la v e
SIO Block Diagram
Rev. 1.20
22
April 14, 2006
HT49RV5/HT49CV5
¨
Slave mode operation
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²CLR
[m].i², ²CPL [m]², ²CPLA [m]² read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Step1: CKS don¢t care and select M1, M0 =11
Step2: Select CSEN, MLS (the same as the master)
Step3: Set SBEN
Step4: Writing data to SBDR
-
data is stored in the TXRX buffer
-
waiting for master clock signal (and SCS): SCK
-
go to step 5
Each line of port A has the capability of waking-up the
device.
Note: SIO internal operation:
* SCK (SCS) received
* output data in TXRX buffer and SDI data
is shifted into TXRX buffer
* data transferred, data in TXRX buffer is
latched into SBDR
Each I/O port has a pull-high option. Once the pull-high
option is selected, the I/O port has a pull-high resistor,
otherwise, there¢s none. Take note that a non-pull-high
I/O port operating in input mode will cause a floating
state.
The PA3 pin is pin-shared with the PFD signal. If the
PFD option is selected, the output signal in the output
mode of PA3 will be the PFD signal generated by the
timer/event counter overflow signal. The input mode always retains its original functions. Once the PFD option
is selected, the PFD output signal is controlled by the
PA3 data register only. Writing a ²1² to PA3 data register
will enable the PFD output function and writing a ²0² will
force the PA3 pin to remain at ²0². The I/O functions of
PA3 are shown below.
Step5: Check WCOL
-
WCOL=1, clear WCOL, go to step 4
-
WCOL=0, go to step 6
Step6: Check TRFor waiting for serial bus interrupt
Step7: Read data from SBDR
Step8: Clear TRF
Step9: Go to step 4
Input/Output Ports
There are 20 bidirectional input/output lines in the
microcontroller, labeled as PA, PB, PC and PD, which
are mapped to the data memory of [12H], [14H], [16H]
and [18H], respectively. All of these I/O ports can be
used for input and output operations. For input operation, these ports are non-latching, that is, the inputs
must be ready at the T2 rising edge of instruction ²MOV
A,[m]² (m=12H, 14H, 16H or 18H). For output operation,
all the data is latched and remains unchanged until the
output latch is rewritten.
I/O
I/P
Mode (Normal)
PA3
Note:
I/P
(PFD)
O/P
(PFD)
Logical
Output
Logical
Input
PFD
(Timer on)
The PFD frequency is the timer/event counter
overflow frequency divided by 2.
The descriptions of PFD control signal and PFD output
frequency are listed in the following table.
Timer
PA3 Data PA3 Pad
Timer Preload
Register
State
Value
Each I/O line has its own control register (PAC, PBC,
PCC, PDC) to control the input/output configuration.
With this control register, CMOS output or Schmitt Trigger input with or without pull-high resistor structures can
be reconfigured dynamically under software control. To
function as an input, the corresponding latch of the control register must write a ²1². The input source also depends on the control register. If the control register bit is
²1², the input will read the pad state. If the control register bit is ²0², the contents of the latches will move to the
in t e rn a l b u s . Th e l at t er i s p o s s i bl e i n t h e
²read-modify-write² instruction.
PFD
Frequency
OFF
X
0
0
X
OFF
X
1
U
X
ON
N
0
0
X
ON
N
1
PFD
fTMR/[2´(M-N)]
Note:
For an output function, CMOS is the only configuration.
These control registers are mapped to locations 13H,
15H, 17H and 19H.
²X² stands for unused
²U² stands for unknown
²M² is ²65536² for PFD0 or PFD1
²N² is preload value for timer/event counter
²fTMR² is input clock frequency for timer/event
counter
The PA0 and PA1 pins are pin-shared with the BZ and
BZ signal, respectively. If the BZ/BZ option is selected,
the output signal in the output mode of PA0/PA1 will be
the buzzer signal generated by the multi-function timer.
The input mode always remains in its original function.
Once the BZ/BZ option is selected, the buzzer output
signal are controlled by the PA0/PA1 data register only.
After a chip reset, these input/output lines remain at high
levels or floating state (depending on pull-high options).
Each bit of these input/output latches can be set or
cleared by ²SET [m].i² and ²CLR [m].i² (m=12H, 14H,
16H or 18H) instructions.
Rev. 1.20
Logical
Input
O/P
(Normal)
23
April 14, 2006
HT49RV5/HT49CV5
V
C o n tr o l B it
Q
D
D a ta B u s
W r ite C o n tr o l R e g is te r
P u ll- h ig h
P A
P A
P A
P A
P A
P B
P C
P C
P D
P D
P D
P D
P D
P D
Q
C K
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
D a ta B it
Q
D
W r ite D a ta R e g is te r
C K
S
Q
M
P A 0 /P A 1 /P A 3 /P D 0 /P D 1
B Z /B Z /P F D /P W M 0 /P W M 1
M
R e a d D a ta R e g is te r
U
0 fo
1 fo
0 fo
1 fo
r P
r P
r P
r P
D 4
D 5
D 6
D 7
o n
o n
o n
o n
U
0 /B Z
1 /B Z
2
3 /P
4 ~ P
0 /A
6
7 /R
0 /P
1 /P
4 /IN
5 /IN
6 /T
7 /T
F D
A 7
N 0 ~ P B 3 /A N 3
M T
W M
W M
T 0
T 1
M R
M R
1
1
0
0
X
P F D E N
(P A 3 )
X
S y s te m W a k e -u p
( P A o n ly )
IN T
IN T
T M R
T M R
D D
O P 0 ~ O P 7
ly
ly
ly
ly
Input/Output Ports
The I/O function of PA0/PA1 are shown below.
PA0 I/O
It is recommended that unused or not bonded out I/O
lines should be set as output pins by software instructions to avoid consuming power under input floating
state.
I
I
O O O O O O O O
PA1 I/O
I
O
I
PA0 Mode
X X C B B C B B B B
PA1 Mode
X C X X X C C C B B
PWM
PA0 Data
X X D 0
PA1 Data
X D X X X D1 D D X X
PA0 Pad Status
I
I
D 0
B D0 0
0
B
PA1 Pad Status
I
D
I
I D1 D D 0
B
The microcontroller provides a 2 channel and
(6+2)/(7+1) (dependent on options) bits PWM output
shared with PD0/PD1. The PWM channels have their
data registers denoted as PWM0 (1AH), PWM1 (1BH).
The frequency source of the PWM counter comes from
fSYS. The PWM registers are two 8-bit registers. The
waveforms of PWM outputs are as shown. Once the
PD0/PD1 are selected as the PWM outputs and the output function of PD0/PD1 are enabled (PDC.0/PDC.1
=²0²), writing ²1² to PD0/PD1 data register will enable
the PWM output function and writing ²0² will force the
PD0/PD1 to remain at ²0².
Note:
I
I
I
O O O O O
1 D0 0
1
B
0
1
²I² input; ²O² output
²D, D0, D1² Data
²B² buzzer option, BZ or BZ
²X² don¢t care
²C² CMOS output
The PB0~PB3 can also be used as A/D converter inputs. The A/D function will be described later. There is a
function shared with PD0/PD1. If the PWM function is
enabled, the PWM0/PWM1 signal will appear on
PD0/PD1 (if PD0/PD1 is operating in the output mode).
Writing a ²1² to PD0~PD1 data register will enable the
PWM output function and writing a ²0² will force the
PD0~PD1 to remain at ²0². The I/O functions of
PD0/PD1 are as shown.
I/O
I/P
Mode (Normal)
PD0
PD1
Rev. 1.20
Logical
Input
O/P
(Normal)
I/P
(PWM)
O/P
(PWM)
Logical
Output
Logical
Input
PWM0
PWM1
A (6+2) bits mode PWM cycle is divided into four modulation cycles (modulation cycle 0~modulation cycle 3).
Each modulation cycle has 64 PWM input clock period.
In a (6+2) bit PWM function, the contents of the PWM
register is divided into two groups. Group 1 of the PWM
register is denoted by DC which is the value of
PWM.7~PWM.2.
The group 2 is denoted by AC which is the value of
PWM.1~PWM.0.
24
April 14, 2006
HT49RV5/HT49CV5
In a (7+1) bits mode PWM cycle, the duty cycle of each
modulation cycle is shown in the table.
In a (6+2) bits mode PWM cycle, the duty cycle of each
modulation cycle is shown in the table.
Parameter
AC (0~3)
Duty Cycle
i<AC
DC + 1
64
Modulation cycle i
(i=0~3)
Parameter
Duty Cycle
i<AC
DC + 1
128
i³AC
DC
128
Modulation cycle i
(i=0~1)
DC
64
i³AC
AC (0~1)
A (7+1) bits mode PWM cycle is divided into two modulation cycles (modulation cycle0~modulation cycle 1).
Each modulation cycle has 128 PWM input clock period.
The modulation frequency, cycle frequency and cycle
duty of the PWM output signal are summarized in the
following table.
In a (7+1) bits PWM function, the contents of the PWM
register is divided into two groups. Group 1 of the PWM
register is denoted by DC which is the value of
PWM.7~PWM.1.
PWM
Modulation Frequency
PWM Cycle PWM Cycle
Frequency
Duty
fSYS/64 for (6+2) bits mode
fSYS/256
fSYS/128 for (7+1) bits mode
[PWM]/256
The group 2 is denoted by AC which is the value of
PWM.0.
fS
/2
Y S
[P W M ] = 1 0 0
P W M
2 5 /6 4
2 5 /6 4
2 5 /6 4
2 5 /6 4
2 5 /6 4
2 6 /6 4
2 5 /6 4
2 5 /6 4
2 5 /6 4
2 6 /6 4
2 6 /6 4
2 6 /6 4
2 5 /6 4
2 5 /6 4
2 6 /6 4
2 6 /6 4
2 6 /6 4
2 5 /6 4
2 6 /6 4
[P W M ] = 1 0 1
P W M
[P W M ] = 1 0 2
P W M
[P W M ] = 1 0 3
P W M
2 6 /6 4
P W M
m o d u la tio n p e r io d : 6 4 /fS
M o d u la tio n c y c le 0
Y S
M o d u la tio n c y c le 1
P W M
M o d u la tio n c y c le 2
c y c le : 2 5 6 /fS
M o d u la tio n c y c le 3
M o d u la tio n c y c le 0
Y S
(6+2) PWM Mode
fS
Y S
/2
[P W M ] = 1 0 0
P W M
5 0 /1 2 8
5 0 /1 2 8
5 0 /1 2 8
5 1 /1 2 8
5 0 /1 2 8
5 1 /1 2 8
5 1 /1 2 8
5 1 /1 2 8
5 1 /1 2 8
5 1 /1 2 8
5 2 /1 2 8
[P W M ] = 1 0 1
P W M
[P W M ] = 1 0 2
P W M
[P W M ] = 1 0 3
P W M
5 2 /1 2 8
P W M
m o d u la tio n p e r io d : 1 2 8 /fS
Y S
M o d u la tio n c y c le 0
M o d u la tio n c y c le 1
P W M
c y c le : 2 5 6 /fS
M o d u la tio n c y c le 0
Y S
(7+1) PWM Mode
Rev. 1.20
25
April 14, 2006
HT49RV5/HT49CV5
converter circuit is powered-on. The EOCB bit (bit6 of
the ADCR) is the end of A/D conversion flag. Check this
bit to know when the A/D conversion is completed.
A/D Converter
The 4 channels and 8 bit resolution A/D converter are
implemented in these microcontrollers. The reference
voltage is VDD. The A/D converter contains 3 special
registers which are; ADR (25H), ADCR (26H) and
ACSR (27H). The ADR contain the A/D result register is
read-only. After the A/D conversion is completed, the
ADR should be read to get the conversion result data.
The ADCR is an A/D converter control register, which
defines the A/D channel number, analog channel select,
start A/D conversion control bit and the end of A/D conversion flag. If the user wishes to start an A/D conversion, they should define the PB configuration, select the
converted analog channel, and give the START bit a rising edge and falling edge (0®1®0). At the end of the
A/D conversion, the EOCB bit is cleared. The ACSR is
the A/D clock setting register, which is used to select the
A/D clock source.
The START bit of the ADCR is used to begin the conversion of the A/D converter. Giving the START bit a rising
edge and falling edge means that the A/D conversion
has started. In order to ensure that the A/D conversion is
completed, the START should remain at ²0² until the
EOCB is cleared to ²0² (end of A/D conversion).
Bit 7 of the ACSR is used for testing purposes only. It
cannot be used by the user. The bit 1 and bit 0 of the
ACSR are used to select the A/D clock sources.
When the A/D conversion has completed, the A/D interrupt request flag will be set. The EOCB bit is set to ²1²
when the START bit is set from ²0² to ²1².
Important Note for A/D initialisation:
Special care must be taken to initialise the A/D converter each time the Port B A/D channel selection bits
are modified, otherwise the EOCB flag may be in an undefined condition. An A/D initialisation is implemented
by setting the START bit high and then clearing it to zero
within 10 instruction cycles of the Port B channel selection bits being modified. Note that if the Port B channel
selection bits are all cleared to zero then an A/D initialisation is not required.
The A/D converter control register is used to control the
A/D converter. Bits 1~0 of the ADCR are used to select
an analog input channel. There¢s a total of four channels
to select. The bit5~bit3 of the ADCR are used to set the
PB0~PB3 configurations. PB can be an analog input or
digital I/O line determined by these 3 bits. Once a PB
line is selected as an analog input, the I/O functions and
pull-high resistor of this I/O line are disabled and the A/D
Bit No.
Label
0
1
ADCS0
ADCS1
Function
Selects the A/D converter clock source
00= system clock/2
01= system clock/8
10= system clock/32
11= undefined
2~6
¾
Unused bit, read as ²0²
7
TEST
For test mode used only
ACSR (27H) Register
Bit No.
Label
0
1
ACS0
ACS1
Function
2, 5
¾
3
4
PCR0
PCR1
Defines the port B configuration select. If PCR0 and PCR1 are all zero, the ADC circuit is
powered off to reduce power consumption
6
EOCB
Indicates end of A/D conversion. (0= end of A/D conversion)
Each time bits 3~4 change state the A/D should be initialised by issuing a START signal,
otherwise the EOCB flag may have an undefined condition. See ²Important note for A/D initialisation².
7
START
Starts the A/D conversion.
0®1®0= Start
0®1= Reset A/D converter and set EOCB to ²1².
Defines the analog channel select.
Unused bit, read as ²0²
ADCR (26H) Register
Rev. 1.20
26
April 14, 2006
HT49RV5/HT49CV5
ACS1
ACS0
Analog Channel
0
0
AN0
0
1
AN1
1
0
AN2
1
1
AN3
Analog Input Channel Selection
Register
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
ADR
D7
D6
D5
D4
D3
D2
D1
D0
Note:
D0~D7 is the A/D conversion result data bit LSB~MSB.
PCR1
PCR0
3
2
1
0
0
0
PB3
PB2
PB1
PB0
0
1
PB3
PB2
PB1
AN0
1
0
PB3
PB2
AN1
AN0
1
1
AN3
AN2
AN1
AN0
Port B Configuration
The following programming example illustrates how to setup and implement an A/D conversion. The method of polling
the EOCB bit in the ADCR register is used to detect when the conversion cycle is complete.
Example: using EOCB Polling Method to detect end of conversion
clr
EADI
; disable ADC interrupt
mov
a,00000001B
mov
ACSR,a
; setup the ACSR register to select fSYS/8 as the A/D clock
mov
mov
a,00110000B
ADCR,a
:
; setup ADCR register to configure Port PB0~PB3 as A/D inputs
; and select AN0 to be connected to the A/D converter
; As the Port B channel bits have changed the following START
; signal (0-1-0) must be issued within 10 instruction cycles
:
Start_conversion:
clr
START
set
START
clr
START
Polling_EOC:
sz
EOCB
jmp
polling_EOC
mov
a,ADR
mov
adr_buffer,a
:
:
jmp
Start_conversion
Rev. 1.20
; reset A/D
; start A/D
; poll the ADCR register EOCB bit to detect end of A/D conversion
; continue polling
; read conversion result from the ADR register
; save result to user defined memory
; start next A/D conversion
27
April 14, 2006
HT49RV5/HT49CV5
M in im u m
o n e in s tr u c tio n c y c le n e e d e d , M a x im u m
te n in s tr u c tio n c y c le s a llo w e d
S T A R T
E O C B
A /D
tA
P C R 1 ~
P C R 0
s a m p lin g tim e
A /D
tA
D C S
0 0 B
s a m p lin g tim e
A /D
tA
D C S
1 1 B
1 1 B
s a m p lin g tim e
D C S
1 0 B
0 0 B
1 . P B p o rt s e tu p a s I/O s
2 . A /D c o n v e r te r is p o w e r e d o ff
to r e d u c e p o w e r c o n s u m p tio n
A C S 1 ~
A C S 0
0 0 B
P o w e r-o n
R e s e t
0 1 B
0 0 B
0 1 B
S ta rt o f A /D
c o n v e r s io n
S ta rt o f A /D
c o n v e r s io n
S ta rt o f A /D
c o n v e r s io n
R e s e t A /D
c o n v e rte r
R e s e t A /D
c o n v e rte r
E n d o f A /D
c o n v e r s io n
1 : D e fin e P B c o n fig u r a tio n
2 : S e le c t a n a lo g c h a n n e l
tA D C
A /D c o n v e r s io n tim e
N o te :
A /D
tA D
tA
C S
D C
c lo c k m u s t b e fS
= 3 2 tA D
= 7 6 tA D
Y S
/2 , fS
Y S
/8 o r fS
Y S
R e s e t A /D
c o n v e rte r
E n d o f A /D
c o n v e r s io n
A /D
tA D C
c o n v e r s io n tim e
d o n 't c a r e
E n d o f A /D
c o n v e r s io n
A /D
tA D C
c o n v e r s io n tim e
/3 2
A/D Conversion Timing
purpose data memory. The VFD display memory can be
read and written to only by an indirect addressing mode
using MP1. When data is written into the display data
area, it is automatically read by the VFD driver which
then generates the corresponding VFD driving signals.
To turn the display on or off, a ²1² or a ²0² is written to
the corresponding bit of the display memory, respectively. The figure illustrates the mapping between the
display memory and VFD pattern for the HT49RV5/
HT49CV5.
VFD Display Memory
The HT49RV5/HT49CV5 provides an area of embedded data memory for the VFD display. This area is located from 40H to 55H of the RAM at Bank 1. The Bank
Pointer (BP; located at 04H of the RAM) is the switch for
the RAM and the VFD display memory. When the BP is
set as ²1², any data written into 40H~55H will affect the
VFD display. When the BP is written as ²0² any data
written into 40H~55H is meant to access the general
SEG15~
SEG12
SEG11~
SEG8
SEG7~
SEG4
SEG3~
SEG0
Grid0
41HU
41HL
40HU
40HL
Grid1
43HU
43HL
42HU
42HL
Grid2
45HU
45HL
44HU
44HL
Grid3
47HU
47HL
46HU
46HL
Grid4
49HU
49HL
48HU
48HL
Grid5
4BHU
4BHL
4AHU
4AHL
Grid6
4DHU
4DHL
4CHU
4CHL
Grid7
4FHU
4FHL
4EHU
4EHL
Grid8
51HU
51HL
50HU
50HL
Grid9
53HU
53HL
52HU
52HL
Grid10
55HU
55HL
54HU
54HL
b7
b4 b3
b0
HU
HL
Higher 4 bits
Lower 4 bits
VFD Display Memory
Rev. 1.20
28
April 14, 2006
HT49RV5/HT49CV5
VFD Display Control Register - VFDC
Bit No.
2~0
Label
There is a low voltage reset circuit (LVR) implemented in
the microcontroller. This function can be enabled/disabled by options.
Function
Selects the VFD display mode
000= 4 grids, 16 segments
001= 5 grids, 16 segments
010= 6 grids, 16 segments
VGS2~
011= 7 grids, 15 segments
VGS0 100= 8 grids, 14 segments
101= 9 grids, 13 segments
110= 10 grids, 12 segments
111= 11 grids, 11 segments
3
¾
4
VFDE
7~5
Low Voltage Reset
If the supply voltage of the device is within the range
0.9V~VLVR, such as changing a battery, the LVR will automatically reset the device internally.
The LVR includes the following specifications:
· The low voltage (0.9V~VLVR) has to remain in its origi-
nal state for longer than 1ms. If the low voltage state
does not exceed 1ms, the LVR will ignore it and will
not perform a reset function.
Unused bit, read as ²0²
Controls the VFD display
(1=enable; 0=disable)
· The LVR uses an ²OR² function with the external RES
signal to perform a chip reset.
Sets the VFD dimming quantity
000= set pulse width to 1/16.
001= set pulse width to 2/16.
010= set pulse width to 4/16.
VDM2~V
011= set pulse width to 10/16.
DM0
100= set pulse width to 11/16.
101= set pulse width to 12/16.
110= set pulse width to 13/16.
111= set pulse width to 14/16.
The relationship between VDD and VLVR is shown below.
V D D
5 .5 V
V
VFD clock source may come from the RTC or the system clock/4 (fSYS/4).
0 .9 V
Note:
G r id 0
S e g m e n ts
O N
G r id 1
S e g m e n ts
O N
A ll
S e g m e n ts
O F F
L V R
2 .2 V
At power-on initial, the 11-grid, 11-segment & 1/16 pulse
width are set and the VFD display is disabled.
G r id 1
O P R
5 .5 V
3 .0 V
VFDC (28H) Register
G r id 0
V
V D D
0 V
VOPR is the voltage range for proper chip
operation at 4MHz system clock.
V E E
V D D
0 V
V E E
V D D
0 V
V E E
V D D
0 V
V E E
V D D
0 V
V E E
VFD Driver Output
Rev. 1.20
29
April 14, 2006
HT49RV5/HT49CV5
V
D D
5 .5 V
V
L V R
L V R
D e te c t V o lta g e
0 .9 V
0 V
R e s e t S ig n a l
N o r m a l O p e r a tio n
R e s e t
*1
R e s e t
*2
Low Voltage Reset
Note:
*1: To make sure that the system oscillator has stabilized, the SST provides an extra delay of 1024 system
clock pulses before starting normal operation.
*2: Since the low voltage has to maintain its original state for longer than 1ms, therefore a 1ms delay enters the
reset mode.
Options
The following shows the configuration options in the HT49RV5/HT49CV5. All these options should be defined in order
to ensure a properly functioning system.
Options
OSC type selection. This option is to decide if an RC or crystal or 32768Hz crystal oscillator is chosen as the system
clock.
fWDT: WDT clock source selection. There are three types of selections: system clock/4 or RTC OSC or WDT OSC
fS: VFD, RTC and Buzzer clock source selection. There are two types of selections: system clock/4 or RTC OSC
WDT enable/disable selection. WDT can be enabled or disabled by option.
WDT time-out period selection. There are four types of selection: WDT clock source divided by fWDT/212~fWDT/213,
fWDT/213~fWDT/214, fWDT/214~fWDT/215 or fWDT/215~fWDT/216
CLR WDT times selection. This option defines the method to clear the WDT by instruction. ²One time² means that
the ²CLR WDT² instructions can clear the WDT. ²Two times² means only if both of the ²CLR WDT1² and ²CLR
WDT2² instructions have been executed, the WDT can be cleared.
Buzzer output frequency selection. There are eight types of frequency signals for buzzer output: fS/2~fS/28,
²fS² means the clock source selected by options.
Wake-up selection. This option defines the wake-up capability. External I/O pins (PA only) all have the capability to
wake-up the chip from a HALT by a falling edge. (bit option)
Pull-high selection.
This option is to determine whether the pull-high resistance is viable or not in the input mode of the I/O ports. PA,
PB0~PB3, PC6~PC7, PD0~PD1 and PD4~PD7 can be independently selected. (bit option)
RMT Pull-high selection. This option is to determine whether a pull-high resistance is viable or not in the input pin.
I/O pins shared with other function selections. PA0/BZ, PA1/BZ, PA3/PFD: PA0, PA1 and PA3 can be set as I/O pins
or buzzer outputs.
VFD driver clock selection. There are 8 types of frequency signals for the VFD driver circuits: fS/20~fS/27.
²fS² stands for the clock source selection by options.
VFD ON/OFF at HALT selection, VFD ON at HALT works only when the VFD clock source selects RTC OSC
Rev. 1.20
30
April 14, 2006
HT49RV5/HT49CV5
Options
LVR selection
LVR has enable or disable options
PFD selection. If PA3 is set as a PFD output, there are two types of selections; One is PFD0 as the PFD output, the
other is PFD1 as the PFD output. PFD0, PFD1 are the timer overflow signals of the Timer/Event Counter 0,
Timer/Event Counter 1, respectively.
PWM selection: (7+1) or (6+2) mode
PD0: level output or PWM0 output
PD1: level output or PWM1 output
INT0 or INT1 triggering edge: Disable; high to low; low to high; low to high or high to low
SIOCLK: Serial interface clock. There are falling edge, rising edge or triggering edge
CSEN: Serial bus selection: enable or disable
WCOL: SBDR write conflict
Application Circuits
V
D D
0 .0 1 m F *
S E G
G
S E G
~ S E
V D D
1 0 0 k W
0 .1 m F
R E S
0
r id
1
G
~ S E
0 ~ G
1 /G r
1 5 /G
G 1
r id
id 1
r id
1 0 k W
0
5
0
V F D
6
V E E
V F D
P o w e r S u p p ly
0 .1 m F
0 .1 m F *
V S S
O S C
C ir c u it
S C S
C L K
S D I
S D O
O S C 1
O S C 2
S e e r ig h t s id e
O S C 1
R
O S C
/4
O S C 2
O S C 1
C ry s ta l S y s te m
O s c illa to r
O S C 3
O S C 4
P
P
P D 4 /IN T 0
P D 6 /T M R 0
P D
P D
P
~
P D 7 /T M R 1
P
P A 0 /B
P A 1 /B
P A
A 3 /P F
A 4 ~ P A
B 0 /A N
B 3 /A N
C 6 ~ P C
0 /P W M
1 /P W M
C 2
Z
Z
O S C 2
2
D
7
O S C 1
0
~
P
P D 5 /IN T 1
3
7
O S C 2
0
3 2 7 6 8 H z C ry s ta l S y s te m
O s c illa to r
O S C 1 a n d O S C 2 le ft
u n c o n n e c te d
1
O S C
H T 4 9 R V 5 /H T 4 9 C V 5
Note:
Y S
R M T
C 1
3 2 7 6 8 H z
fS
R C S y s te m O s c illa to r
5 6 k W < R O S C < 1 .5 M W
C ir c u it
The resistance and capacitance for reset circuit should be designed in such a way as to ensure that the VDD is
stable and remains within a valid operating voltage range before bringing RES to high.
Rev. 1.20
31
April 14, 2006
HT49RV5/HT49CV5
Instruction Set Summary
Description
Instruction
Cycle
Flag
Affected
Add data memory to ACC
Add ACC to data memory
Add immediate data to ACC
Add data memory to ACC with carry
Add ACC to data memory with carry
Subtract immediate data from ACC
Subtract data memory from ACC
Subtract data memory from ACC with result in data memory
Subtract data memory from ACC with carry
Subtract data memory from ACC with carry and result in data memory
Decimal adjust ACC for addition with result in data memory
1
1(1)
1
1
1(1)
1
1
1(1)
1
1(1)
1(1)
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
C
1
1
1
1(1)
1(1)
1(1)
1
1
1
1(1)
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Increment data memory with result in ACC
Increment data memory
Decrement data memory with result in ACC
Decrement data memory
1
1(1)
1
1(1)
Z
Z
Z
Z
Rotate data memory right with result in ACC
Rotate data memory right
Rotate data memory right through carry with result in ACC
Rotate data memory right through carry
Rotate data memory left with result in ACC
Rotate data memory left
Rotate data memory left through carry with result in ACC
Rotate data memory left through carry
1
1(1)
1
1(1)
1
1(1)
1
1(1)
None
None
C
C
None
None
C
C
Move data memory to ACC
Move ACC to data memory
Move immediate data to ACC
1
1(1)
1
None
None
None
Clear bit of data memory
Set bit of data memory
1(1)
1(1)
None
None
Mnemonic
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
AND data memory to ACC
OR data memory to ACC
Exclusive-OR data memory to ACC
AND ACC to data memory
OR ACC to data memory
Exclusive-OR ACC to data memory
AND immediate data to ACC
OR immediate data to ACC
Exclusive-OR immediate data to ACC
Complement data memory
Complement data memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Rev. 1.20
32
April 14, 2006
HT49RV5/HT49CV5
Instruction
Cycle
Flag
Affected
Jump unconditionally
Skip if data memory is zero
Skip if data memory is zero with data movement to ACC
Skip if bit i of data memory is zero
Skip if bit i of data memory is not zero
Skip if increment data memory is zero
Skip if decrement data memory is zero
Skip if increment data memory is zero with result in ACC
Skip if decrement data memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1(2)
1(2)
1(2)
1(2)
1(3)
1(3)
1(2)
1(2)
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read ROM code (current page) to data memory and TBLH
Read ROM code (last page) to data memory and TBLH
2(1)
2(1)
None
None
No operation
Clear data memory
Set data memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of data memory
Swap nibbles of data memory with result in ACC
Enter power down mode
1
1(1)
1(1)
1
1
1
1(1)
1
1
None
None
None
TO,PDF
TO(4),PDF(4)
TO(4),PDF(4)
None
None
TO,PDF
Mnemonic
Description
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
x: Immediate data
m: Data memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Ö: Flag is affected
-: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle
(four system clocks).
(2)
: If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more
cycle (four system clocks). Otherwise the original instruction cycle is unchanged.
(3) (1)
:
(4)
Rev. 1.20
and (2)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the
²CLR WDT1² or ²CLR WDT2² instruction, the TO and PDF are cleared.
Otherwise the TO and PDF flags remain unchanged.
33
April 14, 2006
HT49RV5/HT49CV5
Instruction Definition
ADC A,[m]
Add data memory and carry to the accumulator
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADCM A,[m]
Add the accumulator and carry to data memory
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,[m]
Add data memory to the accumulator
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the accumulator.
Operation
ACC ¬ ACC+[m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,x
Add immediate data to the accumulator
Description
The contents of the accumulator and the specified data are added, leaving the result in the
accumulator.
Operation
ACC ¬ ACC+x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADDM A,[m]
Add the accumulator to the data memory
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the data memory.
Operation
[m] ¬ ACC+[m]
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
34
April 14, 2006
HT49RV5/HT49CV5
AND A,[m]
Logical AND accumulator with data memory
Description
Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
AND A,x
Logical AND immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_AND operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ANDM A,[m]
Logical AND data memory with the accumulator
Description
Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
CALL addr
Subroutine call
Description
The instruction unconditionally calls a subroutine located at the indicated address. The
program counter increments once to obtain the address of the next instruction, and pushes
this onto the stack. The indicated address is then loaded. Program execution continues
with the instruction at this address.
Operation
Stack ¬ Program Counter+1
Program Counter ¬ addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR [m]
Clear data memory
Description
The contents of the specified data memory are cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
35
April 14, 2006
HT49RV5/HT49CV5
CLR [m].i
Clear bit of data memory
Description
The bit i of the specified data memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR WDT
Clear Watchdog Timer
Description
The WDT is cleared (clears the WDT). The power down bit (PDF) and time-out bit (TO) are
cleared.
Operation
WDT ¬ 00H
PDF and TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
0
¾
¾
¾
¾
CLR WDT1
Preclear Watchdog Timer
Description
Together with CLR WDT2, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CLR WDT2
Preclear Watchdog Timer
Description
Together with CLR WDT1, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CPL [m]
Complement data memory
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa.
Operation
[m] ¬ [m]
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
36
April 14, 2006
HT49RV5/HT49CV5
CPLA [m]
Complement data memory and place result in the accumulator
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa. The complemented result
is stored in the accumulator and the contents of the data memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DAA [m]
Decimal-Adjust accumulator for addition
Description
The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal
carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a
carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored
in the data memory and only the carry flag (C) may be affected.
Operation
If ACC.3~ACC.0 >9 or AC=1
then [m].3~[m].0 ¬ (ACC.3~ACC.0)+6, AC1=AC
else [m].3~[m].0 ¬ (ACC.3~ACC.0), AC1=0
and
If ACC.7~ACC.4+AC1 >9 or C=1
then [m].7~[m].4 ¬ ACC.7~ACC.4+6+AC1,C=1
else [m].7~[m].4 ¬ ACC.7~ACC.4+AC1,C=C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
DEC [m]
Decrement data memory
Description
Data in the specified data memory is decremented by 1.
Operation
[m] ¬ [m]-1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DECA [m]
Decrement data memory and place result in the accumulator
Description
Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]-1
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
37
April 14, 2006
HT49RV5/HT49CV5
HALT
Enter power down mode
Description
This instruction stops program execution and turns off the system clock. The contents of
the RAM and registers are retained. The WDT and prescaler are cleared. The power down
bit (PDF) is set and the WDT time-out bit (TO) is cleared.
Operation
Program Counter ¬ Program Counter+1
PDF ¬ 1
TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
1
¾
¾
¾
¾
INC [m]
Increment data memory
Description
Data in the specified data memory is incremented by 1
Operation
[m] ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
INCA [m]
Increment data memory and place result in the accumulator
Description
Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
JMP addr
Directly jump
Description
The program counter are replaced with the directly-specified address unconditionally, and
control is passed to this destination.
Operation
Program Counter ¬addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV A,[m]
Move data memory to the accumulator
Description
The contents of the specified data memory are copied to the accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
38
April 14, 2006
HT49RV5/HT49CV5
MOV A,x
Move immediate data to the accumulator
Description
The 8-bit data specified by the code is loaded into the accumulator.
Operation
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV [m],A
Move the accumulator to data memory
Description
The contents of the accumulator are copied to the specified data memory (one of the data
memories).
Operation
[m] ¬ACC
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
Program Counter ¬ Program Counter+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
OR A,[m]
Logical OR accumulator with data memory
Description
Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
OR A,x
Logical OR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_OR operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ORM A,[m]
Logical OR data memory with the accumulator
Description
Data in the data memory (one of the data memories) and the accumulator perform a
bitwise logical_OR operation. The result is stored in the data memory.
Operation
[m] ¬ACC ²OR² [m]
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
39
April 14, 2006
HT49RV5/HT49CV5
RET
Return from subroutine
Description
The program counter is restored from the stack. This is a 2-cycle instruction.
Operation
Program Counter ¬ Stack
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RET A,x
Return and place immediate data in the accumulator
Description
The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RETI
Return from interrupt
Description
The program counter is restored from the stack, and interrupts are enabled by setting the
EMI bit. EMI is the enable master (global) interrupt bit.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RL [m]
Rotate data memory left
Description
The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RLA [m]
Rotate data memory left and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the
rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ [m].7
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
40
April 14, 2006
HT49RV5/HT49CV5
RLC [m]
Rotate data memory left through carry
Description
The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RLCA [m]
Rotate left through carry and place result in the accumulator
Description
Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the
carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored
in the accumulator but the contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RR [m]
Rotate data memory right
Description
The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRA [m]
Rotate right and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving
the rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i) ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRC [m]
Rotate data memory right through carry
Description
The contents of the specified data memory and the carry flag are together rotated 1 bit
right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
41
April 14, 2006
HT49RV5/HT49CV5
RRCA [m]
Rotate right through carry and place result in the accumulator
Description
Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces
the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is
stored in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
SBC A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SBCM A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SDZ [m]
Skip if decrement data memory is 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. If the result is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, [m] ¬ ([m]-1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SDZA [m]
Decrement data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. The result is stored in the accumulator but the data memory remains
unchanged. If the result is 0, the following instruction, fetched during the current instruction
execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, ACC ¬ ([m]-1)
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
42
April 14, 2006
HT49RV5/HT49CV5
SET [m]
Set data memory
Description
Each bit of the specified data memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SET [m]. i
Set bit of data memory
Description
Bit i of the specified data memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZ [m]
Skip if increment data memory is 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a
dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with
the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, [m] ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZA [m]
Increment data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the next
instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper
instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, ACC ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SNZ [m].i
Skip if bit i of the data memory is not 0
Description
If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data
memory is not 0, the following instruction, fetched during the current instruction execution,
is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i¹0
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
43
April 14, 2006
HT49RV5/HT49CV5
SUB A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the accumulator.
Operation
ACC ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUBM A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the data memory.
Operation
[m] ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUB A,x
Subtract immediate data from the accumulator
Description
The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+x+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SWAP [m]
Swap nibbles within the data memory
Description
The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged.
Operation
[m].3~[m].0 « [m].7~[m].4
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SWAPA [m]
Swap data memory and place result in the accumulator
Description
The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.3~ACC.0 ¬ [m].7~[m].4
ACC.7~ACC.4 ¬ [m].3~[m].0
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
44
April 14, 2006
HT49RV5/HT49CV5
SZ [m]
Skip if data memory is 0
Description
If the contents of the specified data memory are 0, the following instruction, fetched during
the current instruction execution, is discarded and a dummy cycle is replaced to get the
proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZA [m]
Move data memory to ACC, skip if 0
Description
The contents of the specified data memory are copied to the accumulator. If the contents is
0, the following instruction, fetched during the current instruction execution, is discarded
and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed
with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZ [m].i
Skip if bit i of the data memory is 0
Description
If bit i of the specified data memory is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDC [m]
Move the ROM code (current page) to TBLH and data memory
Description
The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved
to the specified data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDL [m]
Move the ROM code (last page) to TBLH and data memory
Description
The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to
the data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
45
April 14, 2006
HT49RV5/HT49CV5
XOR A,[m]
Logical XOR accumulator with data memory
Description
Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XORM A,[m]
Logical XOR data memory with the accumulator
Description
Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XOR A,x
Logical XOR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Rev. 1.20
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
46
April 14, 2006
HT49RV5/HT49CV5
Package Information
56-pin SSOP (300mil) Outline Dimensions
2 9
5 6
B
A
2 8
1
C
C '
G
H
D
Symbol
Rev. 1.20
a
F
E
Dimensions in mil
Min.
Nom.
Max.
A
395
¾
420
B
291
¾
299
C
8
¾
12
C¢
720
¾
730
D
89
¾
99
E
¾
25
¾
F
4
¾
10
G
25
¾
35
H
4
¾
12
a
0°
¾
8°
47
April 14, 2006
HT49RV5/HT49CV5
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shanghai Sales Office)
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233
Tel: 021-6485-5560
Fax: 021-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor Inc. (Shenzhen Sales Office)
43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031
Tel: 0755-8346-5589
Fax: 0755-8346-5590
ISDN: 0755-8346-5591
Holtek Semiconductor Inc. (Beijing Sales Office)
Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031
Tel: 010-6641-0030, 6641-7751, 6641-7752
Fax: 010-6641-0125
Holmate Semiconductor, Inc. (North America Sales Office)
46712 Fremont Blvd., Fremont, CA 94538
Tel: 510-252-9880
Fax: 510-252-9885
http://www.holmate.com
Copyright Ó 2006 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.20
48
April 14, 2006
Similar pages