PHILIPS I74F04D Hex inverter Datasheet

INTEGRATED CIRCUITS
74F04
Hex inverter
Product specification
IC15 Data Handbook
1990 Oct 04
Philips Semiconductors
Product specification
Hex inverter
74F04
FEATURE
PIN CONFIGURATION
• Industrial temperature range available (–40°C to +85°C)
TYPE
1A
1
14
VCC
1Y
2
13
6A
TYPICAL
PROPAGATION
DELAY
TYPICAL SUPPLY
CURRENT
( TOTAL)
2A
3
12
6Y
2Y
4
11
5A
3.5ns
6.9mA
3A
5
10
5Y
3Y
6
9
4A
GND
7
8
4Y
74F04
SF00011
ORDERING INFORMATION
ORDER CODE
DESCRIPTION
COMMERCIAL RANGE
VCC = 5V ±10%, Tamb = 0°C to +70°C
INDUSTRIAL RANGE
VCC = 5V ±10%, Tamb = –40°C to +85°C
PKG DWG #
14-pin plastic DIP
N74F04N
I74F04N
SOT27-1
14-pin plastic SO
N74F04D
I74F04D
SOT108-1
INPUT AND OUTPUT LOADING AND FAN OUT TABLE
PINS
DESCRIPTION
nA
74F (U.L.) HIGH/LOW
Data inputs
LOAD VALUE HIGH/LOW
1.0/1.0
20µA/0.6mA
nY
Data output
50/33
NOTE: One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.
LOGIC DIAGRAM
1A
2A
3A
4A
5A
VCC = Pin 14
GND = Pin 7
6A
1.0mA/20mA
FUNCTION TABLE
1
2
3
4
1Y
2Y
5
6
9
8
11
10
13
12
INPUTS
OUTPUT
A
Y
L
H
H
NOTES:
H = High voltage level
L = Low voltage level
3Y
4Y
5Y
L
6Y
SF00012
LOGIC SYMBOL
IEC/IEEE SYMBOL
1
3
5
9
11 13
1
VCC = Pin 14
GND = Pin 7
1A
2A 3A 4A 5A 6A
1A
2A 3A 4A 5A 6A
2
4
6
8
10
12
1
2
3
4
5
6
9
8
11
10
13
12
SF00013
SF00014
October 4, 1990
2
853-0327 00621
Philips Semiconductors
Product specification
Hex inverter
74F04
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free air temperature range.)
SYMBOL
PARAMETER
RATING
UNIT
VCC
Supply voltage
–0.5 to +7.0
V
VIN
Input voltage
–0.5 to +7.0
V
IIN
Input current
–30 to +5
mA
VOUT
Voltage applied to output in high output state
–0.5 to VCC
V
IOUT
Current applied to output in low output state
40
mA
Tamb
Operating free air temperature range
Commercial range
0 to +70
°C
Industrial range
–40 to +85
°C
–65 to +150
°C
Tstg
Storage temperature range
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
LIMITS
UNIT
MIN
NOM
MAX
5.0
5.5
VCC
Supply voltage
4.5
V
VIH
High-level input voltage
2.0
VIL
Low-level input voltage
0.8
V
IIk
Input clamp current
–18
mA
IOH
High-level output current
–1
mA
IOL
Low-level output current
Tamb
Operating free air temperature range
V
20
mA
Commercial range
0
+70
°C
Industrial range
–40
+85
°C
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
TEST CONDITIONS1
PARAMETER
LIMITS
MIN
VOH
VOL
High-level output voltage
Low-level output voltage
TYP2
UNIT
MAX
VCC = MIN, VIL = MAX
±10%VCC
2.5
VIH = MIN, IOH = MAX
±5%VCC
2.7
VCC = MIN, VIL = MAX
±10%VCC
0.30
0.50
V
VIH = MIN, IOl = MAX
±5%VCC
0.30
0.50
V
-0.73
V
3.4
V
VIK
Input clamp voltage
VCC = MIN, II = IIK
-1.2
V
II
Input current at maximum input
voltage
VCC = MAX, VI = 7.0V
100
µA
IIH
High-level input current
VCC = MAX, VI = 2.7V
20
µA
IIL
Low-level input current
VCC = MAX, VI = 0.5V
IOS
Short-circuit output current3
VCC = MAX
ICC
Supply current (total)
-60
-0.6
mA
-150
mA
mA
ICCH
VCC = MAX
VIN = GND
2.8
4.2
ICCL
VCC = MAX
VIN = 4.5V
10.2
15.3
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, IOS tests should be performed last.
October 4, 1990
3
Philips Semiconductors
Product specification
Hex inverter
74F04
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
tPLH
tPHL
PARAMETER
Propagation delay
A to Y
VCC = +5.0V ± 10%
Tamb = 0°C to +70°C
CL = 50pF, RL = 500Ω
VCC = +5.0V
Tamb = +25°C
CL = 50pF, RL = 500Ω
TEST
CONDITION
Waveform 1
VCC = +5.0V ± 10%
Tamb = –40°C to +85°C
CL = 50pF, RL = 500Ω
MIN
TYP
MAX
MIN
MAX
MIN
MAX
2.4
1.5
3.7
3.2
5.0
4.3
2.4
1.5
6.0
5.3
1.5
1.1
8.0
6.5
UNIT
ns
AC WAVEFORMS
VM
A
VM
tPHL
tPLH
VM
Y
VM
SF00015
Waveform 1. Propagation delay for inverting outputs
NOTE:
For all waveforms, VM = 1.5V.
TEST CIRCUIT AND WAVEFORMS
VCC
NEGATIVE
PULSE
VIN
tw
90%
VM
D.U.T.
RT
CL
RL
AMP (V)
VM
10%
VOUT
PULSE
GENERATOR
90%
10%
tTHL (tf )
tTLH (tr )
tTLH (tr )
tTHL (tf )
0V
AMP (V)
90%
90%
POSITIVE
PULSE
DEFINITIONS:
RL = Load resistor;
see AC ELECTRICAL CHARACTERISTICS for value.
CL = Load capacitance includes jig and probe capacitance;
see AC ELECTRICAL CHARACTERISTICS for value.
RT = Termination resistance should be equal to ZOUT of
pulse generators.
VM
VM
10%
Test Circuit for Totem-Pole Outputs
10%
tw
0V
Input Pulse Definition
INPUT PULSE REQUIREMENTS
family
amplitude VM
74F
3.0V
1.5V
rep. rate
tw
tTLH
tTHL
1MHz
500ns
2.5ns
2.5ns
SF00006
October 4, 1990
4
Philips Semiconductors
Product specification
Hex inverter
74F04
DIP14: plastic dual in-line package; 14 leads (300 mil)
1990 Oct 04
5
SOT27-1
Philips Semiconductors
Product specification
Hex inverter
74F04
SO14: plastic small outline package; 14 leads; body width 3.9 mm
1990 Oct 04
6
SOT108-1
Philips Semiconductors
Product specification
Hex inverter
74F04
NOTES
1990 Oct 04
7
Philips Semiconductors
Product specification
Hex inverter
74F04
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Document order number:
yyyy mmm dd
8
Date of release: 10-98
9397-750-05053
Similar pages