Hirose IC11S-BUR-EJL Single slot smt connectors for card-bus based pc card Datasheet

Single Slot SMT Connectors For Card-Bus Based PC Cards
IC11S Series
PC Card Standard Compliant
Reduced height : 5.6mm high
■Features
Wide variety of options
1. PC Card Standard compliant:
(1)Board Mounting
➀Standard type
➁Reverse type
• Grounding is required to meet the high speed signal
requrements of the PC card standard. Grounding reliability is
achieved with a grounding plate and 8 grounding contacts.
• Type 1, type 2 and type 3 cards are covered.
• Terminals for ground clipping are provided.
2. Space saving
Smaller size reduces occupied area on PC boards as
compared to previous products.
3. Reduced Height:
Connector height is minimized to 5.6mm, making possible
thinner product designs.
4. Eject mechanism with high-level functionality
Hirose Electric's original ejection mechanism provides an
higher degree of card ejection over existing products. This
improves the operational qualities of card removal. (Patents
pending)
5. Wide Variety of Options Available
• Standard type mounts to the top of the PC board and reverse
type mounts on the underside of the board
• Three types of eject buttons; rigid, flexible and POP-UP.All
types can be installed on the right or left side of the ejector.
• Available with standoff to utilize space under the connector for
mounting other parts.
6. Light-weight
Weight of 12.7g for normal button type helps achieve the
reduced weight required in today’s products.
A2
(2)Types of eject button
➀Rigid button
➁Foldering button
➂Pop-up button
(3)Position of eject buttons
➀Right
➁Left
(4)Standoffs
➀None
➁2.2mm
■Product Specifications
Ratings
Operating temperature -55ç to +85ç(Note.1) Storage temperature -40ç to +70ç(Note.2)
Current rating
0.5A
Voltage rating
125V AC
Item
Operating humidity
Relativehumidity 95% max.
Storage humidity
(With no dew-fall)
Specification
40% to 70%(Note.2)
Conditions
1.Insulation resistance 1000M ohms min.
2.Withstanding voltage No flashover or insulation breakdown.
3.Contact resistance 60m ohms max. (initial value)
500V DC
500V AC
1mA
4.Vibration
Frequency: 10 to 2000 Hz, full amplitude of 1.52 mm or
acceleration of 147 m/s2(peak), 4 hours in each of the 3 directions.
No electrical discontinuity of 100ns or more
5.Humidity (Steady state) Insulation resistance: 100M ohms min.
96 hours at temperature of 40ç and humidity of 90% to 95%
6.Temperature cycle
(-55ç:30min./+5ç to 35ç:MAX 5min/85ç:30min/+5
-35ç:MAX 5min.) 5 cycles
Insulation resistance: 100M ohms min.
7.Durability
Variations from initial contact resistance: 20m
(Insertion/withdrawal) ohms max.
No deformation of components affecting
performance.
8.Resistance to
Soldering heat
10000 cycles at 400 to 600 cycles per hour
Reflow: At the recommended temperature profile
Manual soldering: 300ç for 3 seconds
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature
Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during
transportation.
■Material
SMT unit
Parts
Material
Insulator
PPS
Finish
Black
Remarks
UL94V-0
Card connected section
Brass
Contact section: gold plating
Lead section: solder plating
Ground plate
Phosphor bronze
Contact section: gold plating
Lead section: solder plating
----------
----------
----------
Contact
Eject metal fittings
Stainless steel
----------
Guide unit
Item
Material
Finish
Remarks
Guide plate
Stainless steel
----------
----------
Push rod
Stainless steel
----------
----------
Rigid button type resin section
PBT
Color : Black
UL94V-0
resin section
PBT
Color : Black
UL94V-0
spring
Stainless steel
----------
----------
spring pin
Stainless steel
resin section
PBT
frame metal
spring
pin
Foldering
button type
Eject Button
POP-UP type
Nut
----------
----------
Color : Black
UL94V-0
Stainless steel
----------
----------
Steel
----------
----------
Brass
Nickel plating
----------
Steel
----------
M2X0.4
A3
■Ordering Information
SMT Unit
IC11S A - 68 PLR - 1.27SF - EJ R
1
2
3
4
5
6
7
1
Series name : IC11S
5
1.27SF : 1.27mm pitch SMT connector
2
Standoff type
Blank : none
A
: 2.2mm
6
With ejector
EJ : with ejector
7
Eject button positions
R : right
L : left
3
Number of contacts : 68
4
Board Mounting Type:
PL : standard type
PLR : reverse type
Guide Unit
IC11S A - BUR - FEJ R
8
8
Series name : IC11S
9
Standoff type
Blank: none
A : 2.2mm
10
Board Mounting Type
BD : standard type
BUR : reverse type
9
10
11
12
11
Eject button type
EJ : rigid button
FEJ : Foldering button
PEJ : POP-UP button
12
Eject button positions
R : right
L : left
(Note.) IC11S Series will be used in combination of SMT unit with guide unit. When using, please select
the same type for the following items. Please note that other combinations cannot be used.
• Series name
• Standoff
• Board-installed type
• Eject button positions
A4
(1⇔8)
(2⇔9)
( 4 ⇔ 10 )
( 7 ⇔ 12 )
■Standard
Right rigid button type
34.4 MAX
3
59
42.545
P= 0.635
SMT unit ( 1 )
No.1
No.35
No.2
GND
No.34
eject metal fittings movable range
GND
C
20.5
7.4
10MAX 7MAX
No.36
No.68
72
85.6: in card insertion
51.5
PUSH
PUSH
A
6
guide unit ( 2 )
( 34.9)
none
2.2mm
No.36
No.68
(27.6)
4.8
No.34
A
B
No.35
Standoff
type
No.2
stroke:9
54.9
3
No.1
59.5
(18.6)
5.9
3
➀SMT unit
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
IC11S-68PL-1.27SF-EJR
640-1007-3
IC11SA-68PL-1.27SF-EJR
640-1009-9
IC11S-BD-EJR
IC11SA-BD-EJR
640-1071-2
640-1073-8
3
5.2
5.6
7.8
Part Number
C
Weight
(mm)
(g)
0.1
2.3
12.7
13.1
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A5
■Standard
Left rigid button type
34.4MAX
3
59
SMT unit ( 1 )
42.545
P= 0.635
No.1
C
GND
eject metal fittings movable range
No.35
No.68
No.2
No.34
GND
20.5
7.4
10MAX 7MAX
No.36
72
85.6: in card insertion
51.5
PUSH
PUSH
A
59.5
(18.6)
3
stroke:9
(27.6)
5.9
3
54.9
6
( 34.9 )
guide unit ( 2 )
No.35
No.36
No.34
A
➀SMT unit
➁Guide unit
Part Number
CL No.
none
IC11S-68PL-1.27SF-EJL
640-1008-6
IC11S-BD-EJL
640-1072-5
IC11SA-68PL-1.27SF-EJL
640-1010-8
IC11SA-BD-EJL
640-1074-0
2.2mm
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A6
No.68
Standoff
type
Part Number
B
No.2
4.8
No.1
CL No.
A
(mm)
B
(mm)
3
5.2
5.6
7.8
C
Weight
(mm)
(g)
0.1
2.3
12.7
13.1
■Standard
Right flexible button type
34.4 MAX
59
42.545
P=0.635
SMT unit ( 1 )
No.35
No.1
No.68
No.2
GND
eject metal fittings movable range
20.5
7.4
10MAX 7MAX
No.36
C
GND
No.34
54.9
guide unit ( 2 )
(27.6)
stroke:9
button thrust volume(10.5)
A
5
3
59.5
(18.6)
5.9
3
(93.6): in card ejection
72
85.6: in card insertion
51.5
PUSH
PUSH
A
(34.55)
(42.05)
4.8
No.35
Standoff
type
none
2.2mm
No.34
No.2
A
B
No.1
➀SMT unit
Part Number
No.68
No.36
➁Guide unit
A
(mm)
B
(mm)
640-1075-3
3
5.6
0.1
13.1
640-1077-9
5.2
7.8
2.3
13.5
CL No.
Part Number
CL No.
IC11S-68PL-1.27SF-EJR
640-1007-3
IC11S-BD-FEJR
IC11SA-68PL-1.27SF-EJR
640-1009-9
IC11SA-BD-FEJR
C
Weight
(mm)
(g)
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A7
■Standard
Left flexible. button type
34.4MAX
59
3
SMT unit ( 1 )
42.545
P=0.635
No.35
No.1
GND
eject metal fittings movable range
No.34
No.36
GND
72
85.6: in card insertion
59.5
5.9
3
(18.6)
(27.6)
(93.6): in card ejection
51.5
PUSH
PUSH
A
20.5
7.4
10 MAX 7 MAX
C
No.68
No.2
54.9
stroke:9
button thrust volume(10.5)
5
3
guide unit ( 2 )
(34.55)
(42.05)
No.35
No.36
No.34
Standoff
type
none
2.2mm
A
➀SMT unit
Part Number
Part Number
CL No.
A
(mm)
B
(mm)
C
Weight
(mm)
(g)
IC11S-68PL-1.27SF-EJL
640-1008-6
IC11S-BD-FEJL
640-1076-6
3
5.6
0.1
13.1
IC11SA-68PL-1.27SF-EJL
640-1010-8
IC11SA-BD-FEJL
640-1078-1
5.2
7.8
2.3
13.5
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A8
No.68
➁Guide unit
CL No.
B
No.2
4.8
No.1
■Standard
Right POP-UP button type
34.4 MAX
3
59
42.545
P= 0.635
SMT unit ( 1 )
No.1
No.2
No.68
No.36
No.34
eject metal fittings movable range
GND
C
20.5
7.4
10MAX 7MAX
GND
No.35
59.5
DR
3
54.9
9.1(Pop-up volume)
guide unit ( 2 )
5
none
2.2mm
No.2
No.34
No.35
No.36
No.68
5
No.1
A
B
(35.1)
Standoff
type
86.4(button stored position)
5.9
3
84.5(button thrust position)
72
51.5
A
PUSH
PUSH
A
➀SMT unit
Part Number
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
C
Weight
(mm)
(g)
IC11S-68PL-1.27SF-EJR
640-1007-3
IC11S-BD-PEJR
640-1081-6
3
5.7
0.1
14.7
IC11SA-68PL-1.27SF-EJR
640-1009-9
IC11SA-BD-PEJR
640-1083-1
5.2
7.9
2.3
15.1
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A9
■Standard
Left POP-UP button type
34.4 MAX
3
59
SMT unit ( 1 )
42.545
P= 0.635
No.1
eject metal fittings movable range
No.35
No.68
No.2
No.34
No.36
GND
20.5
7.4
10MAX 7MAX
C
GND
72
59.5
5.9
9.1(Pop-up volume)
3
54.9
5
guide unit ( 2 )
(35.1)
No.2
No.34
No.36
No.68
A
5
No.1
No.35
Standoff
type
none
2.2mm
➀SMT unit
Part Number
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
A
(mm)
C
Weight
(mm)
(g)
IC11S-68PL-1.27SF-EJL
640-1008-6
IC11S-BD-PEJL
640-1082-9
3
5.7
0.1
14.7
IC11SA-68PL-1.27SF-EJL
640-1010-8
IC11SA-BD-PEJL
640-1084-4
5.2
7.9
2.3
15.1
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A10
B
84.5(button thrust position)
3
DL
86.4(button stored position)
51.5
PUSH
PUSH
A
■Reverse
Right rigid button type
34.4 MAX
3
59
42.545
SMT unit ( 1 )
P= 0.635
No.68
No.35
No.34
No.2
GND
C
GND
20.5
6
10MAX 7MAX
No.36
eject metal fittings movable range
No.1
A
(18.6)
59.5
54.9
6
(34.9)
stroke:9
3
(27.6)
5.9
72
85.6: in card insertion
51.5
PUSH
PUSH
3
No.36
No.35
No.34
No.2
No.1
4.8
No.68
A
B
guide unit ( 2 )
➀SMT unit
➁Guide unit
Standoff
type
Part Number
CL No.
none
IC11S-68PLR-1.27SF-EJR
640-1003-2
IC11SA-68PLR-1.27SF-EJR
640-1005-8
2.2mm
CL No.
A
(mm)
B
(mm)
IC11S-BUR-EJR
640-1055-6
2.7
5.6
0.1
13.1
IC11SA-BUR-EJR
640-1057-1
4.9
7.8
2.3
13.6
Part Number
C
Weight
(mm)
(g)
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A11
■Reverse
Left rigid button type
34.4 MAX
3
59
42.545
P= 0.635
No.35
No.68
eject metal fittings movable range
C
No.2
No.34
No.36
GND
85.6: in card insertion
72
51.5
PUSH
PUSH
A
20.5
6
10MAX 7MAX
GND
SMT unit ( 1 )
No.1
59.5
(18.6)
(27.6)
5.9
3
3
54.9
6
guide unit ( 2 )
No.36
No.35
No.2
No.1
A
4.8
No.68
No.34
Standoff
type
none
2.2mm
➀SMT unit
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
IC11S-68PLR-1.27SF-EJL
640-1004-5
IC11S-BUR-EJL
640-1056-9
2.7
5.6
0.1
13.1
IC11SA-68PLR-1.27SF-EJL
640-1006-0
IC11SA-BUR-EJL
640-1058-4
4.9
7.8
2.3
13.6
Part Number
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A12
B
(34.9)
C
Weight
(mm)
(g)
■Reverse
Right flexible button type
34.4 MAX
3
59
42.545
P= 0.635
No.68
SMT unit ( 1 )
GND
No.34
No.35
No.1
No.2
GND
eject metal fittings movable range
C
20.5
6
10MAX 7MAX
No.36
59.5
54.9
guide unit ( 2 )
(27.6)
stroke:9
button thrust :(10.5)
A
5
3
(18.6)
5.9
3
93.6: in card ejection
72
85.6: in card insertion
51.5
PUSH
PUSH
A
( 34.55 )
No.36
No.35
No.34
No.2
No.1
4.8
No.68
A
B
( 42.05 )
➀SMT unit
➁Guide unit
Standoff
type
Part Number
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
none
IC11S-68PLR-1.27SF-EJR
640-1003-2
IC11S-BUR-FEJR
640-1059-7
2.7
5.6
0.1
13.5
IC11SA-68PLR-1.27SF-EJR
640-1005-8
IC11SA-BUR-FEJR
640-1061-9
4.9
7.8
2.3
14
2.2mm
C
Weight
(mm)
(g)
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A13
■Reverse
Left flexible button type
34.4 MAX
3
59
42.545
eject metal fittings movable range
P= 0.635
No.68
No.35
No.34
No.2
GND
C
SMT unit ( 1 )
No.1
GND
A
20.5
6
10MAX 7MAX
No.36
72
85.6: in card insertion
(18.6)
5.9
59.5
3
54.9
stroke:9
button thrust :(10.5)
5
( 27.6 )
93.6: in card ejection
51.5
PUSH
PUSH
3
guide unit ( 2 )
( 34.55 )
No.36
No.35
No.34
No.2
No.1
Standoff
type
none
2.2mm
A
4.8
No.68
➀SMT unit
Part Number
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
C
Weight
(mm)
(g)
IC11S-68PLR-1.27SF-EJL
640-1004-5
IC11S-BUR-FEJL
640-1060-6
2.7
5.6
0.1
13.5
IC11SA-68PLR-1.27SF-EJL
640-1006-0
IC11SA-BUR-FEJL
640-1062-1
4.9
7.8
2.3
14
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A14
B
( 42.05 )
■Reverse
Right POP-UP button type
34.4 MAX
3
59
42.545
SMT unit ( 1 )
P= 0.635
No.68
No.35
No.34
No.2
GND
C
GND
20.5
6
10 MAX 7MAX
No.36
eject metal fittings movable range
No.1
A
UR
54.9
9.1(Pop-up volume)
3
86.4(button stored position)
59.5
84.5(button thrust position)
5.9
72
51.5
A
PUSH
PUSH
3
5
guide unit ( 2 )
No.36
No.35
No.34
No.2
No.1
5
No.68
A
B
(35.1)
➀SMT unit
➁Guide unit
Standoff
type
Part Number
CL No.
none
IC11S-68PLR-1.27SF-EJR
640-1003-2
IC11SA-68PLR-1.27SF-EJR
640-1005-8
2.2mm
CL No.
A
(mm)
B
(mm)
IC11S-BUR-PEJR
640-1065-0
2.7
5.6
0.1
15.1
IC11SA-BUR-PEJR
640-1067-5
4.9
7.8
2.3
15.6
Part Number
C
Weight
(mm)
(g)
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A15
■Reverse
Left POP-UP button type
34.4MAX
3
59
42.545
P= 0.635
No.35
No.68
eject metal fittings movable range
C
No.2
No.34
No.36
GND
72
51.5
5.9
59.5
9.1(Pop-up volume)
guide unit ( 2 )
5
(35.1)
No.36
No.35
No.2
No.1
A
5
No.68
No.34
Standoff
type
none
2.2mm
➀SMT unit
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
IC11S-68PLR-1.27SF-EJL
640-1004-5
IC11S-BUR-PEJL
640-1066-2
2.7
5.6
0.1
15.1
IC11SA-68PLR-1.27SF-EJL
640-1006-0
IC11SA-BUR-PEJL
640-1068-8
4.9
7.8
2.3
15.6
Part Number
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A16
B
84.5(button thrust position)
3
UL
86.4(button stored position)
PUSH
PUSH
A
20.5
6
10MAX 7MAX
GND
SMT unit ( 1 )
No.1
C
Weight
(mm)
(g)
■PCB mounting pattern
●Standard Type
●Without standoff
●Without standoff
(left button)
2-Ø2.2 +0.1
+0
2
2
3.05MIN
27.95MAX
34.5MIN
55.9MIN
59.5±0.05
2MIN
(6.6)
17.9MIN
0.3MIN
installed section
1.6MAX
0.8MAX
54.75±0.05
4.75±0.05
1
card edge position
shielded board-pressed are
26.8MIN
21MIN
21MIN
26.8MIN
shielded board-pressed area
58.1±0.05
card edge position
28.5MIN
31.4MIN
54.75±0.05
7MIN
4.75±0.05
58.1±0.05
0.8MAX
1.6MAX
17.9MIN
2
34.5 MIN
30 MIN
30 MAX
52.8±0.05
2
48.5MAX
31.4MIN
28.5MIN
7MIN
(6.6)
0.8MAX
installed section
34.5 MIN
30 MIN
52.8±0.05
48.5MAX
0.3MIN
30 MIN
0.8MAX
(right button)
2-Ø2.2 +0.1
+0
2MIN
3.05MIN
27.95MAX
34.5MIN
2
2
55.9MIN
59.5±0.05
●Standoff 2.2mm
52.8±0.05
installed section
card edge position
58.1±0.05
47.5±0.05
54.75±0.05
50.6MAX
56.85MAX
shielded boardpressed area
22.6MAX
27.6MIN
(6.6)
(common to both right and left buttons)
2
7MIN
2
parts installation-prohibited area
2-Ø2.2 +0.1
+0
2MIN
3.05MIN
2
59.5MAX
Note.1)
area and
area show the pattern-inhibited area.
However
area will be the pattern-inhibited area only when guide unit is "IC11S-BD-PEJ✽".
Note.2) Indicated dimensions are symmetrical to the center of the card insertion slot.
A17
BPCB mounting pattern (Enlarged)
●Standard type
48±0.05
46.2725±0.05
3.7275±0.05
Ø1
.3
±
0.
05
No.35
68-0.37±0.03
1.9±0.1
GND
Ø1
.3
3±0.1
No.34
1.4±0.1
2±0.1
No.2
1.2±0.1
GND
P=0.635±0.03
A18
No.68
No.1
1.4±0.1
3±0.1
2±0.05
±0
.0
5
●Reverse Type
●Without standoff
●Without standoff
(left button)
2MIN
27.95MAX
34.5MIN
50.8MAX
54.6MIN
59.5±0.05
2
2
2
26.8MIN
3.05MIN
2
7MIN
26.8MIN
shielded board-pressed area
-Ø
25.8MIN
.1
+0 0
2+
2.
56.7±0.05
28.5MIN
54.75±0.05
12-2MIN
4.75±0.05
1
60MIN
52.8±0.05
15.2MIN
card edge position
30.25±0.05
18.45±0.05
20.25±0.05 14.75±0.05
4.75±0.05 3.925±0.05
56.7±0.05
2
installed section
installed section
card edge position
2-
Ø2
7MIN
60MIN
52.8±0.05
15.2MIN
(5.2)
2MAX
2
.2
+
+0 0.1
2MIN
1
shielded board-pressed area
3.05MIN
3.925±0.05
4.75±0.05
20.25±0.05 14.75±0.05
18.45±0.05
30.25±0.05
(right button)
27.95MAX
34.5MIN
2
50.8MAX
2
54.6MIN
2
59.5±0.05
●Standoff 2.2mm
56.7±0.05
4.75±0.05
54.75±0.05
2
7MIN
2
50.6MAX
56.85MIN
installed section
card edge position
26.2MIN
52.8±0.05
21.2MAX
(5.2)
(common to both right and left buttons)
parts installation-prohibited area
shielded board-pressed area
2-Ø2.2 +0.1
+0
2MIN
3.05MIN
2
59.5±0.05
Note.1)
area and
area show the pattern-inhibited area.
However
area will be the pattern-inhibited area only when guide unit is "IC11S-BUR-PEJ".
Note.2) Indicated dimensions are symmetrical to the center of the card insertion slot
A19
BPCB mounting pattern (Enlarged)
●Reverse type
A20
■How To Install In Board(Standard Type)
(1)Install SMT unit.
(2)Position the lock section of guide unit into the hole of SMT unit.
(3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.)
(Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation.
(4)Screw 2 spots to guide unit from the back side of board.
Screw designation
Pitch
Recommended tightening torque
M2
0.4
1.5 to 2.0 (kgf • cm)
A21
■How To Install In Board(Reverse Type)
(1)Install SMT unit.
(2)Position the lock section of guide unit into the hole of SMT unit.
(3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.)
(Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation.
(4)Screw 2 spots to guide unit from the back side of board.
A22
Screw designation
Pitch
Recommended tightening torque
M2
0.4
1.5 to 2.0 (kgf • cm)
■PreCautions In Installation To Boards
1. After installation of SMT unit to boards, verify that the stroke arm of SMT unit
and the push rod of guide unit are located on the positions shown in fig.➀.
Also note that guide unit cannot be solder reflowed.
Pict.➀
Guide unit
SMT unit
Push rod
Stroke arm
2. Note that the stroke arm of SMT unit and the push rod of guide unit cannot be combined when
located in the position as shown in fig.➁.
Pict.➁
Guide unit
SMT unit
If located in the position shown in fig.➁ move it to the position shown in fig. ➀ by fingers.
Guide unit
SMT unit
3. After SMT unit and guide unit are combined, state will be found as follows :
●When the push rod was pressed:
intervention
●When the push rod was extracted:
intervention
A23
■Pre Caution In Handling
Guide plate is metallic, having some sharp-edged portions. Handle carefully to prevent injury to fingers.
Do not wrench the card up and down severely in the midst of insertion. This may cause damage to the connectors or cards.
Up
Down
A24
■Temperature Profile
5sec.max
board surface temperature(ç)
250
240ç
200
200ç
Applicable Conditions
Reflow system : IR reflow
160ç
150
150ç
Solder
: Paste type 63 Sn/37 Pb
(Flux content 9 wt%)
100
Test board Glass epoxy 60mm x 60mm x 1.6 mm
Metal mask thickness: 0.15 mm
50
25ç
0
start
Recommended temperature profile.
(30s)
60-90s
preheating time
(60s)
60
120
(20-30s)
soldering time
The temperature may be slightly changed according to the
solder paste type and amount.
time(seconds)
A25
Single Slot SMT Connectors For Card-Bus Based PC Cards
IC11S Series (New POP-UP Button)
PC Card Standard Compliant
Reduced height : 5.6mm high
■Features
Wide variety of options
1. PC Card Standard compliant:
(1)Board Mounting
➀Standard type
➁Reverse type
• Grounding is required to meet the high speed signal requirements
of the PC card standard. Grounding reliability is achieved with a
grounding plate and 8 grounding contacts.
• Type1, type2and type3cards are covered.
• Terminals for ground clipping are provided.
2. Reduced pattern-inhibited area
Pattern-inhibited area is reduced,compared to our conventional
product.
3. Light-Weight
(2)Position of eject buttons
➀Right
➁Left
(3)Standoffs
➀0.0mm
➁2.2mm
Approx. 12% of weight reduced.
Compared to conventional type, it only weighs 13.1g for standard
type with 0mm standoff.
4. Reduced Height:
Connector height is minimized to 5.6mm, making possible thinner
product designs.
5. Eject mechanism with high-level functionality
Hirose Electric's original ejection mechanism provides an higher
degree of card ejection over existing products. This improves the
operational qualities of card removal. (Patents pending)
Standard type
6. Wide Variety of Options Available
• Standard type mounts to the top of the PC board and reverse type
mounts on the underside of the board
• Three types of eject buttons; rigid, flexible and POP-UP.All types
can be installed on the right or left side of the ejector.
• Available with standoff to utilize space under the connector for
mounting other parts.
Reverse type
A26
■Product Specifications
Ratings
Current rating
0.5A
Operating temperature
Voltage rating
125V AC
Operating humidity
Item
-55ç to +85ç(Note.1)
Storage temperature
Relativehumidity 95% or less
Storage humidity
(With no dew-fall)
Specification
-40ç to +70ç(Note.2)
40% to 70%(Note.2)
Conditions
1.Insulation resistance
1000M ohms min.
500V DC
2.Withstanding voltage
No flashover or insulation breakdown.
500V AC
3.Contact resistance
60m ohms max. (initial value)
1mA
4.Vibration
No electrical discontinuity of 100ns or more
Frequency: 10 to 2000 Hz, full amplitude of 1.52 mm or
acceleration of 147 m/s2(peak), 4 hours in each of the 3 directions.
5.Humidity (Steady state) Insulation resistance: 100M ohms min.
6.Temperature cycle
Insulation resistance: 100M ohms min.
7.Durability
(Insertion/withdrawal)
Variations from initial contact resistance: 20m ohms
max.
8.Resistance to
Soldering heat
No deformation of components affecting performance.
96 hours at temperature of 40ç and humidity of 90% to 95%
(-55ç:30min.➝+5ç to 35ç:MAX 5min➝85ç:30min➝
(+5-35ç:MAX 5min.) 5 cycles
10000 cycles at 400 to 600 cycles per hour
Reflow: At the recommended temperature profile
Manual soldering: 300ç for 3 seconds
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature
Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during
transportation.
■Materials
●SMT unit
Parts
Material
Insulator
PPS
Card connected section
Brass
Ground plate
Phosphor bronze
Terminal
Stainless steel
Eject metal fittings
Finish
Remarks
Color : Black
UL94V-0
Contact section: gold plating
Lead section: solder plating
Contact section: gold plating
Lead section: solder plating
–––––
–––––
–––––
–––––
●Guide unit
Description
Material
Finish
Remarks
Guide plate
Stainless steel
–––––
–––––
Push rod
Stainless steel
Eject Button
–––––
–––––
Resin section
PBT
Color : Black
UL94V-0
Spring
Steel
–––––
–––––
Zinc alloy
–––––
–––––
Cam
A27
■Ordering Information
●SMT Unit
IC11S A - 68 PLR - 1.27SF - EJ R
1
1
Series name : IC11S
2
Standoff type
2
3
4
5
Blank : none
A
6
7
5
1.27SF : 1.27mm pitch SMT connector
6
With ejector
7
Eject button positions
: 2.2mm
3
Number of contacts : 68
4
Board Mounting Method:
PL
R : right
: standard type
L : left
PLR : reverse type
●Guide Unit
IC11S A - BUR - PNEJ R
8
8
Series name : IC11S
9
Standoff type
9
10
11
11
12
Eject button type
PNEJ : POP-UP button
Blank: none
A : 2.2mm
10
Board Mounting Method
BD
12
: standard type
Eject button positions
R : right
BUR : reverse type
L : left
(Note.) IC11S Series will be used in combination of SMT unit with guide unit. When using, please select the
same type for the following items. Note that other combinations cannot be used.
• Series name
• Standoff type
• Board Mounting Method
• Eject button positions
A28
(1⇔8)
(2⇔9)
( 4 ⇔ 10 )
( 7 ⇔ 12 )
■Standard
Right POP-UP button type
34.4MAX
3
59
42.545
No.35
SMT Unit(1)
eject metal fittings movable range
No.2
No.36
C
No.68
GND
No.34
10 MAX
7.4
7 MAX
No.1
GND
P=0.635
20.5
AS
A
PUSH
PUSH
59.5
( 17.55)
5.9
3
86.3 (button stored position)
84.3 (button thrust position)
( 28.05)
72
51.5
PNL
2.35
11.8
NR
NDRA
27.45
No.2
No.34
5
B
5
No.1
A
Guide unit(2)
No.35
Standoff
type
0mm
2.2mm
➀SMT unit
Part Number
No.36
No.68
➁Guide unit
CL No.
10.1(Pop-up volume)
( 35.05 )
(66.25)
Part Number
CL No.
A
(mm)
B
(mm)
C
(mm)
mass
(g)
IC11S-68PL-1.27SF-EJR
640-1007-3
IC11S-BD-PNEJR
640-1251-4
3
5.6
0.1
13.1
IC11SA-68PL-1.27SF-EJR
640-1009-9
IC11SA-BD-PNEJR
640-1253-0
5.2
7.8
2.3
13.6
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A29
■Standard
Left POP-UP button type
34.4MAX
3
59
42.545
eject metal fittings movable range
P=0.635
No.35
C
SMT Unuit(1)
No.2
No.36
No.68
GND
No.34
10MAX
7.4
7MAX
No.1
GND
20.5
AS
PUSH
PUSH
72
59.5
10.1(Pop-up volume)
(17.55)
5.9
3
(28.05)
84.3(button stored position)
86.3(button thrust position)
51.5
PNR
11.8
2.35
NL
NDLA
27.45
(35.05)
(66.25)
No.1
No.2
No.34
Guide unit(2)
A
B
5
5
No.35
Standoff
type
0mm
2.2mm
No.36
➀SMT unit
Part Number
No.68
➁Guide unit
CL No.
Part Number
A
(mm)
B
(mm)
C
(mm)
mass
(g)
IC11S-68PL-1.27SF-EJL
640-1008-6
IC11S-BD-PNEJL
640-1252-7
3
5.6
0.1
13.1
IC11SA-68PL-1.27SF-EJL
640-1010-8
IC11SA-BD-PNEJL
640-1254-2
5.2
7.8
2.3
13.6
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A30
CL No.
■Reverse
Right POP-UP button type
34.4 MAX
3
59
42.545
SMT Unit(1)
P=0.635
No.2
No.36
eject metal fittings movable range
No.35
No.1
GND
C
20.5
10MAX
6
7 MAX
No.34
No.68
GND
A
10.1(Pop-up volume)
( 17.55 )
86.3(button stored position)
59.5
84.3(button thrust position)
3
5.9
72
( 28.05 )
51.5
PNR
2.35
11.8
NURA
27.45
( 35.05 )
( 66.25 )
5
Guide unit(2)
No.36
No.35
A
B
5
No.68
No.34
➀SMT unit
No.2
No.1
➁Guide unit
Standoff
type
Part Number
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
C
(mm)
mass
(g)
0mm
IC11S-68PLR-1.27SF-EJR
640-1003-2
IC11S-BUR-PNEJR
640-1255-5
2.7
5.6
0.1
13.3
IC11SA-68PLR-1.27SF-EJR
640-1005-8
IC11SA-BUR-PNEJR
640-1257-0
4.9
7.8
2.3
13.7
2.2mm
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A31
■Reverse
Left POP-UP button type
34.4 MAX
59
42.545
3
eject metal fittings movable range
P=0.635
No.34
No.68
GND
SMT Unit(1)
No.35
No.1
GND
20.5
10 MAX
6
7 MAX
C
No.2
No.36
A
PUSH
PUSH
72
(28.05 )
59.5
5.9
3
10.1 (Pop-up volume)
(17.55 )
84.3 (button stored position)
86.3 (button thrust position)
51.5
PNL
2.35
11.8
NULA
27.45
( 35.05 )
( 66.25 )
5
No.36
No.35
Guide unit(2)
A
B
5
No.68
No.34
Standoff
type
➀SMT unit
Part Number
No.2
No.1
➁Guide unit
CL No.
Part Number
CL No.
A
(mm)
B
(mm)
C
(mm)
mass
(g)
0mm
IC11S-68PLR-1.27SF-EJL
640-1004-5
IC11S-BUR-PNEJL
640-1256-8
2.7
5.6
0.1
13.3
2.2mm
IC11SA-68PLR-1.27SF-EJL
640-1006-0
IC11SA-BUR-PNEJL
640-1258-3
4.9
7.8
2.3
13.7
Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together.
Note.2) Dimensions for card fitting are in accordance with "PC Card Standard".
Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot.
A32
BPCB mounting pattern
●Standard Type
●Without standoff
●Without standoff
(left button)
2-Ø2.2 +0.1
0
3.05MIN
2
2
52.8±0.05
48.5MAX
17.9MIN
0.3MIN
2
Installed cection
1.6MAX
0.8MAX
21MIN
Shielded boardpressed area
30 MIN
54.75±0.05
4.75±0.05
2MIN
2-Ø2.2 +0.1
0
2MIN
55.9MIN
59.5±0.05
Card edge position
Shielded boardpressed area
21MIN
Card edge position
7MIN
31.4MIN
54.75±0.05
58.1±0.05
4.75±0.05
58.1±0.05
0.8MAX
1.6MAX
17.9MIN
2
34.5 MIN
30MAX
31.4MIN
7MIN
(6.6)
0.8MAX
Installed cection
34.5 MIN
30MAX
52.8±0.05
48.5MAX
0.3MIN
30 MIN
0.8MAX
(6.6)
(right button)
3.05MIN
2
2
55.9MIN
59.5±0.05
●Standoff 2.2mm
52.8±0.05
Installed cection
Card edge position
58.1±0.05
4.75±0.05
54.75±0.05
2
2
50.6MAX
56.85MIN
22.6MAX
27.6MIN
(6.6)
(common to both right and left buttons)
Parts installation prohibited area
7MIN
Shielded board-pressed area
2-Ø2.2 +0.1
0
2MIN
3.05MIN
2
59.5±0.05
Note.1)
area show the pattern-inhibited area.
Note.2) Indicated dimensions are symmetrical to the center
of the card insertion slot.
BPCB mounting pattern (Enlarged)
●Standard type
A33
BPCB mounting pattern
●Reverse Type
●Without standoff
(common to both right and left buttons)
2MAX
.1
+0 0
2
4.75±0.05
2Ø2
.2
2MIN
7MIN
2
7MIN
3.05MIN
2.
-Ø
Card edge position
54.75±0.05
+0
.
0 1
2MIN
Shielded board-pressed area
3.05MIN
1
4.75±0.05
3.925±0.05
20.25±0.05 14.75±0.05
18.45±0.05
30.25±0.05
56.7±0.05
12-2MIN
56.7±0.05
30.25±0.05
18.45±0.05
20.25±0.05 14.75±0.05
3.925±0.05
4.75±0.05
54.75±0.05
Shielded board-pressed area
Installed cection
15.2MIN
(5.2)
2MAX
15.2MIN
(5.2)
Card edge position
4.75±0.05
60MIN
52.8±0.05
2
Installed cection
12-2MIN
60MIN
52.8±0.05
2
1
50.8MAX
54.6MIN
59.5±0.05
2
2
2
2
2
2
50.8MAX
54.6MIN
59.5±0.05
●Standoff 2.2mm
54.75±0.05
2
7MIN
2
50.6MAX
56.85MIN
Card edge position
21.2MAX
4.75±0.05
Installed cection
26.2MIN
52.8±0.05
56.7±0.05
(5.2)
(common to both right and left buttons)
Parts installation prohibited area
Shielded board-pressed area
2-Ø2.2 +0.1
0
2MIN
3.05MIN
2
59.5±0.05
BPCB mounting pattern (Enlarged)
●Reverse type
A34
Note.1)
area show the pattern-inhibited area.
Note.2) Indicated dimensions are symmetrical to the center
of the card insertion slot.
BHow To Install In Board(Standard Type)
(1)Install SMT unit.
(2)Position the lock section of guide unit into the hole of SMT unit.
(3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.)
(Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation.
(4)Screw 2 spots to guide unit from the back side of board.
Screw designation
Pitch
Recommended tightening torque
M2
0.4
0.14 to 0.18 (N • m)
A35
BHow To Install In Board(Reverse Type)
(1)Install SMT unit.
(2)Position the lock section of guide unit into the hole of SMT unit.
(3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.)
(Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation.
(4)Screw 2 spots to guide unit from the back side of board.
A36
Screw designation
Pitch
Recommended tightening torque
M2
0.4
0.14 to 0.18 (N • m)
BCautions In Installation To Boards
1. After installation of SMT unit to boards, verify that the stroke arm of SMT unit
and the push rod of guide unit are located on the positions shown in fig.➀.
Also note that guide unit cannot be solder reflowed.
Pict.➀
Guide unit
SMT unit
Push rod
Stroke arm
2. Note that the stroke arm of SMT unit and the push rod of guide unit cannot be combined when
located in the position as shown in fig.➁.
Pict.➁
Guide unit
SMT unit
If located in the position shown in fig.➁ move it to the position shown in fig. ➀ by fingers.
Guide unit
SMT unit
3. After SMT unit and guide unit are combined, state will be found as follows :
●When the push rod was pressed:
●When the push rod was extracted:
intervention
intervention
A37
BCaution In Handling
Guide plate is metallic, having some sharp-edged portions. Handle carefully to prevent injury to fingers.
Do not wrench the card up and down severely in the midst of insertion. This may cause damage to the connectors or cards.
Up
Down
A38
BInstallation Temperature Profile
5sec.max
board surface temperature(ç)
250
240ç
200
200ç
Applicable Conditions
Reflow system : IR reflow
160ç
150
150ç
Solder
: Paste type 63 Sn/37 Pb
(Flux content 9 wt%)
100
Test board Glass epoxy 60mm x 60mm x 1.6 mm
Metal mask thickness: 0.15 mm
50
25ç
0
start
Recommended temperature profile.
(30s)
60-90s
preheating
(60s)
60
(20-30s)
soldering
120
The temperature may be slightly changed according to the
solder paste type and amount.
time(seconds)
A39
Similar pages