ICST ICS843034A01 Femtoclocksâ ¢ multi-rate lvpecl frequency synthesizer Datasheet

PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
GENERAL DESCRIPTION
FEATURES
The ICS843034-01 is a general purpose, low
ICS
phase noise LVPECL synthesizer which can
HiPerClockS™ generate frequencies for a wide variety of
applications. The ICS843034-01 has a 4:1
input Multiplexer from which the following
inputs can be selected: 1 differential input, 1
single-ended input, or one of two crystal oscillators,
thus making the device ideal for frequency translation or
generation. Each differential LVPECL output pair has an
output divider which can be independently set so that two
different frequencies can be generated. Additionally, each
LVPECL output pair has a dedicated power supply pin so
the outputs can run at 3.3V or 2.5V. The ICS843034-01
also supplies a buffered copy of the reference clock or
crystal frequency on the single-ended REF_CLK pin which
can be enabled or disabled (disabled by default). The output
frequency can be programmed using either a serial or
parallel programming interface.
• Dual differential 3.3V LVPECL outputs which can be set
independently for either 3.3V or 2.5V
• 4:1 Input Mux:
1 differential input
1 single-ended input
2 crystal oscillator interfaces
• CLK, nCLK pair can accept the following differential
input levels: LVPECL, LVDS, LVHSTL, HCSL, SSTL
• TEST_CLK accepts LVCMOS or LVTTL input levels
• Output frequency range: 30.625MHz to 640MHz
• Crystal input frequency range: 12MHz to 40MHz
• VCO range: 490MHz to 640MHz
• Parallel or serial interface for programming feedback divider
and output dividers
• RMS phase jitter at 106.25MHz, using a 25.5MHz crystal
(637kHz to 5MHz): 0.61ps (typical)
The ICS843034-01 has excellent <1ps phase jitter
performance over the 637kHz - 5MHz integration range, thus
making it suitable for use in Fibre Channel, SONET, and
Ethernet/1Gb Ethernet applications.
• Supply voltage modes:
LVPECL outputs (core/outputs):
3.3V/3.3V
3.3V/2.5V
Example applications include systems which must support
both FEC and non FEC rates. In 10Gb Fibre Channel, for
example, you can use a 25.5MHz crystal to generate a
159.375MHz reference clock, and then switch to a
20.544MHz crystal to generate 164.355MHz for 66/64 FEC.
Other applications could include supporting both Ethernet
frequencies and SONET frequencies in an application. When
Ethernet frequencies are needed, a 25MHz crystal can be
used and when SONET frequencies are needed, the input
MUX can be switched to select a 38.88MHz Crystal.
REF_CLK output (core/outputs):
3.3V/3.3V
3.3V/2.5V
• 0°C to 70°C ambient operating temperature
• Available in both standard and lead-free RoHS-compliant
packages
CLK
nCLK
nP_LOAD
VCO_SEL
M0
M1
M2
M3
M4
M5
M6
M7
PIN ASSIGNMENT
M8
NB0
NB1
NB2
OE_REF
OE_A
OE_B
VCC
NA0
NA1
NA2
VEE
48 47 46 45 44 43 42 41 40 39 38 37
1
36
2
35
3
34
4
33
5
32
48-Pin LQFP
6
31
7mm x 7mm x 1.4mm
7
30
package body
8
29
Y Package
9
28
Top View
10
27
11
26
12
25
13 14 15 16 17 18 19 20 21 22 23 24
ICS843034-01
XTAL_OUT1
XTAL_IN1
XTAL_OUT0
XTAL_IN0
TEST_CLK
SEL1
SEL0
VCCA
S_LOAD
S_DATA
S_CLOCK
MR
VEE
P_DIV
VCCO_REF
REF_CLK
VCCO_B
nFOUTB0
FOUTB0
VCCO_A
nFOUTA0
FOUTA0
VCC
TEST
The Preliminary Information presented herein represents a product in prototyping or pre-production. The noted characteristics are based on initial
product characterization. Integrated Circuit Systems, Incorporated (ICS) reserves the right to change any circuitry or specifications without notice.
843034AY-01
www.icst.com/products/hiperclocks.html
1
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
BLOCK DIAGRAM
OE_A
VCO_SEL
XTAL_IN0
XTAL_OUT0
OSC
00
XTAL_IN1
OSC
0
01
XTAL_OUT1
CLK
nCLK
TEST_CLK
10
÷1
÷2
÷3
÷4
÷5
101 ÷6
÷8
111 ÷16
÷
VCCO_A
001
VCCO_B
000
001
010
011
1 ÷4
0 ÷8
PHASE
DETECTOR
FOUTA0
nFOUTA0
1
VCO
011
11
÷M
FOUTB0
nFOUTB0
101
SEL1
111 ÷16
÷
SEL0
P_DIV
OE_B
VCCO_REF
MR
REF_CLK
OE_REF
S_LOAD
S_DATA
S_CLOCK
C
nP_LOAD
M8:M0
TEST
I
L
NA2:NA0
NB2:NB0
843034AY-01
www.icst.com/products/hiperclocks.html
2
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
FUNCTIONAL DESCRIPTION
Nx bits can be hardwired to set the M divider and Nx output
divider to a specific default state that will automatically occur
during power-up. The TEST output is LOW when operating in
the parallel input mode. The relationship between the VCO frequency, the crystal frequency and the M divider is defined as
follows: fVCO = fxtal x M
P
The M value and the required values of M0 through M5 are shown
in Table 3B to program the VCO Frequency Function Table.
Valid M values for which the PLL will achieve lock for a 25MHz
reference are defined as 20 ≤ M ≤ 25. The frequency out is defined as follows: FOUT = fVCO = fxtal x M
N
NxP
Serial operation occurs when nP_LOAD is HIGH and S_LOAD
is LOW. The shift register is loaded by sampling the S_DATA
bits with the rising edge of S_CLOCK. The contents of the
shift register are loaded into the M divider and Nx output divider when S_LOAD transitions from LOW-to-HIGH. The M
divide and Nx output divide values are latched on the HIGHto-LOW transition of S_LOAD. If S_LOAD is held HIGH, data
at the S_DATA input is passed directly to the M divider and Nx
output divider on each rising edge of S_CLOCK. The serial
mode can be used to program the M and Nx bits and test bits
T1 and T0. The internal registers T0 and T1 determine the state
of the TEST output as follows:
NOTE: The functional description that follows describes operation using a 25MHz crystal. Valid PLL loop divider values
for different crystal or input frequencies are defined in the Input Frequency Characteristics, Table 5, NOTE 1.
The ICS843034-01 features a fully integrated PLL and therefore requires no external components for setting the loop bandwidth. A fundamental crystal is used as the input to the onchip oscillator. The output of the oscillator is fed into the phase
detector. A 25MHz crystal provides a 25MHz phase detector
reference frequency. The VCO of the PLL operates over a
range of 490MHz to 640MHz. The output of the M divider is
also applied to the phase detector.
The phase detector and the M divider force the VCO output frequency to be M times the reference frequency by adjusting the
VCO control voltage. Note that for some values of M (either too
high or too low), the PLL will not achieve lock. The output of the
VCO is scaled by a divider prior to being sent to each of the LVPECL
output buffers. The divider provides a 50% output duty cycle.
The ICS843034-01 supports either serial or parallel programming modes to program the M feedback divider and N output
divider. The input divider P can only be changed using the P_DIV
pin. It cannot be changed from the default ÷1 setting using the
serial interface. Figure 1 shows the timing diagram for each mode.
In parallel mode, the nP_LOAD input is initially LOW. The data
on the M, NA, and NB inputs are passed directly to the M divider and both N output dividers. On the LOW-to-HIGH transition of the nP_LOAD input, the data is latched and the M and N
dividers remain loaded until the next LOW transition on
nP_LOAD or until a serial event occurs. As a result, the M and
T1
T0
TEST Output
0
0
LOW
0
1
S_Data, Shift Register Output
1
0
Output of M divider
1
1
CMOS Fout A0
SERIAL LOADING
S_CLOCK
S_DATA
T1
t
S_LOAD
S
t
T0
NB2
NB1 NB0
NA2
NA1
NA0
M8
M7
M6
M5
M4
M3
M2
M1
M0
H
nP_LOAD
t
S
PARALLEL LOADING
M0:M8, P_DIV,
NA0:NA2, NB0:NB2
M, N, P
nP_LOAD
t
S
t
H
S_LOAD
Time
FIGURE 1. PARALLEL & SERIAL LOAD OPERATIONS
843034AY-01
www.icst.com/products/hiperclocks.html
3
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TABLE 1. PIN DESCRIPTIONS
Number
Name
1
M8
2, 3
NB0, NB1
Input
4
NB2
Input
Description
M divider input. Data latched on LOW-to-HIGH trnsition of nP_LOAD
Pulldown
input. LVCMOS/LVTTL interfac levels.
Pullup
Determines output divider value as defined in Table 3C,
Pulldown Function Table. LVCMOS/LVTTL interface levels.
5
OE_REF
Input
Pulldown
6
OE_A
Input
Pullup
7
OE_B
Input
Pullup
8, 14
VCC
Power
9, 10
NA0, NA1
Input
11
NA2
Input
12, 24
VEE
Power
13
TEST
Output
20
FOUTA0,
nFOUTA0
VCCO_A
FOUTB0,
nFOUTB0
VCCO_B
15, 16
17
18, 19
Type
Input
Output enable. Controls enabling and disabling of REF_CLK output.
LVCMOS/LVTTL interface levels.
Output enable. Controls enabling and disabling of FOUTA0,
nFOUTA0 outputs. LVCMOS/LVTTL interface levels.
Output enable. Controls enabling and disabling of FOUTB0,
nFOUTB0 outputs. LVCMOS/LVTTL interface levels.
Core supply pins.
Pullup
Determines output divider value as defined in Table 3C,
Pulldown Function Table. LVCMOS/LVTTL interface levels.
Negative supply pins.
Test output which is ACTIVE in the serial mode of operation.
Output driven LOW in parallel mode.
LVCMOS/LVTTL interface levels.
Output
Differential output for the synthesizer. LVPECL interface levels.
Power
Output supply pin for FOUTA0, nFOUTA0.
Output
Differential output for the synthesizer. LVPECL interface levels.
Power
Output supply pin for FOUTB0, nFOUTB0.
21
REF_CLK
Output
Reference clock output. LVCMOS/LVTTL interface levels.
22
VCCO_REF
Power
23
P_DIV
Input
Pullup/
Pulldown
25
MR
Input
Pulldown
26
S_CLOCK
Input
Pulldown
27
S_DATA
Input
Pulldown
28
S_LOAD
Input
Pulldown
29
VCCA
Power
Output supply pin for REF_CLK.
Input divide select. Float = ÷1 (default), 1 = ÷ 4, 0 = ÷8.
LVCMOS/LVTTL interface levels.
Active High Master Reset. When logic HIGH, forces the internal
dividers are reset causing the true outputs FOUTx to go low and the
inver ted outputs nFOUTx to go high. When logic LOW, the internal
dividers and the outputs are enabled. Asser tion of MR does not
affect loaded M, N, and T values. LVCMOS/LVTTL interface levels.
Clocks in serial data present at S_DATA input into the shift register
on the rising edge of S_CLOCK. LVCMOS/LVTTL interface levels.
Shift register serial input. Data sampled on the rising edge
of S_CLOCK. LVCMOS/LVTTL interface levels.
Controls transition of data from shift register into the dividers.
LVCMOS/LVTTL interface levels.
Analog supply pin.
30, 31
SEL0, SEL1
Input
Pulldown Clock select inputs. LVCMOS/LVTTL interface levels.
32
TEST_CLK
Input
Pulldown Test clock input. LVCMOS/LVTTL interface levels.
37
XTAL_IN0,
XTAL_OUT0
XTAL_IN1,
XTAL_OUT1
CLK
Input
38
nCLK
Input
33, 34
35, 36
Input
Cr ystal oscillator interface.
Input
Cr ystal oscillator interface.
Pulldown Non-inver ting differential clock input.
Pullup/
Inver ting differential clock input.VCC/2 default when left floating.
Pulldown
Continued on next page...
843034AY-01
www.icst.com/products/hiperclocks.html
4
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
Number
Name
Type
39
nP_LOAD
Input
40
VCO_SEL
Input
41, 42, 43,
44, 45, 47, 48
46
M0, M1, M2,
M3, M4, M6, M7
M5
Input
Input
Description
Parallel load input. Determines when data present at M5:M0 is
loaded into M divider, and when data present at NA2:NA0 and
Pulldown
NB2:NB0 is loaded into the N output dividers.
LVCMOS/LVTTL interface levels.
Determines whether synthesizer is in PLL or bypass mode.
Pullup
LVCMOS/LVTTL interface levels.
Pulldown M divider inputs. Data latched on LOW-to-HIGH transition
of nP_LOAD input. LVCMOS/LVTTL interface levels.
Pullup
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
TABLE 2. PIN CHARACTERISTICS
Symbol
Parameter
CIN
Input Capacitance
Test Conditions
Minimum
Typical
4
Maximum
Units
pF
RPULLUP
Input Pullup Resistor
51
kΩ
RPULLDOWN
Input Pulldown Resistor
51
kΩ
ROUT
Output Impedance
843034AY-01
5
www.icst.com/products/hiperclocks.html
5
7
12
Ω
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
TABLE 3A. PARALLEL
AND
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
SERIAL MODE FUNCTION TABLE
Inputs
Conditions
MR
nP_LOAD
M
N
S_LOAD
S_CLOCK
S_DATA
H
X
X
X
X
X
X
Reset. Forces outputs LOW.
L
L
Data
Data
X
X
X
Data on M and N inputs passed directly to the M
divider and N output divider. TEST output forced LOW.
L
↑
Data
Data
L
X
X
L
H
X
X
L
↑
Data
L
H
X
X
↑
L
Data
L
H
X
X
↓
L
Data
M divider and N output divider values are latched.
L
H
X
X
L
X
X
Parallel or serial input do not affect shift registers.
L
H
X
X
H
↑
Data
Data is latched into input registers and remains loaded
until next LOW transition or until a serial event occurs.
Serial input mode. Shift register is loaded with data on
S_DATA on each rising edge of S_CLOCK.
Contents of the shift register are passed to the
M divider and N output divider.
S_DATA passed directly to M divider as it is clocked.
NOTE: L = LOW
H = HIGH
X = Don't care
↑ = Rising edge transition
↓ = Falling edge transition
TABLE 3B. PROGRAMMABLE VCO FREQUENCY FUNCTION TABLE P = ÷1 (P_DIV = FLOAT)
32
16
8
4
2
1
M5
M4
M3
M2
M1
M0
0
1
0
1
0
0
•
•
•
•
•
•
•
550
22
0
1
0
1
1
0
•
•
•
•
•
•
•
•
VCO Frequency
(MHz)
M Divide
500
20
•
625
25
0
1
1
0
0
NOTE 1: These M divide values and the resulting frequencies correspond to crystal or
TEST_CLK input frequency of 25MHz.
1
TABLE 3C. PROGRAMMABLE OUTPUT DIVIDER FUNCTION TABLE
Inputs
N Divider Value
Output Frequency (MHz)
*NX2
*NX1
*NX0
Minimum
Maximum
0
0
0
1
490
640
0
0
1
2
245
320
0
1
0
3
163.33
213.33
0
1
1
4
122.5
160
1
0
0
5
98
128
1
0
1
6
81.67
106.67
1
1
0
8
61.25
80
1
1
1
16
30.625
40
*NOTE: X denotes Bank A or Bank B
843034AY-01
www.icst.com/products/hiperclocks.html
6
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC
4.6V
Inputs, VI
-0.5V to VCC + 0.5V
Outputs, VO (LVCMOS)
-0.5V to VCCO + 0.5V
Outputs, IO (LVPECL)
Continuous Current
Surge Current
50mA
100mA
Package Thermal Impedance, θJA
47.9°C/W (0 lfpm)
Storage Temperature, TSTG
-65°C to 150°C
NOTE: Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the
device. These ratings are stress specifications only. Functional
operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect product reliability.
TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, VCCO_A = VCCO_B = 3.3V±5% OR 2.5V±5%, TA = 0°C TO 70°C
Symbol
Parameter
VCC
VCCA
Test Conditions
Minimum
Typical
Maximum
Units
Core Supply Voltage
2.375
3.3
3.465
V
Analog Supply Voltage
2.375
3.3
3.465
V
VCCO_A,
VCCO_B
Output Supply
Voltage
3.135
3.3
3.465
V
2.375
2.5
2.625
V
IEE
Power Supply Current
185
mA
ICCA
Analog Supply Current
20
mA
VCCO_REF
REF_CLK Output Supply
843034AY-01
www.icst.com/products/hiperclocks.html
7
3.135
3.3
3.465
V
2.375
2.5
2.625
V
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TABLE 4B. LVCMOS/LVTTL DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, VCCO_A = VCCO_B = 3.3V±5% OR 2.5V±5%, TA = 0°C TO 70°C)
Symbol
VIH
VIL
IIH
Parameter
Input
High Voltage
Input
Low Voltage
Input
High Current
Test Conditions
VCO_SEL, SEL0, SEL1, MR,
OE_REF, OE_A, OE_B,
S_LOAD, nP_LOAD, S_DATA,
S_CLOCK, TEST_CLK,
M0:M5, NX0:NX2
P_DIV
VCO_SEL, SEL0, SEL1, MR,
OE_REF, OE_A, OE_B,
S_LOAD, nP_LOAD, S_DATA,
S_CLOCK, TEST_CLK,
M0:M5, NX0:NX2
P_DIV
TEST_CLK, P_DIV, MR,
SEL[1:0], S_CLOCK, S_DATA,
S_LOAD, nP_LOAD, OE_REF
NA2, NB2, M1:M4, M6:M8
NB0, NB1, NA0, NA1, M5,
OE_A, OE_B, VCO_SEL
IIL
VOH
VOL
Input
Low Current
Output
High Voltage
Output Low
Voltage
Minimum
Typical
2
Maximum
Units
VCC + 0.3
V
VCC - 0.4
V
-0.3
0.8
V
0.3
V
VCC = VIN = 3.465V
150
µA
VCC = VIN = 3.465V
5
µA
TEST_CLK, P_DIV, MR,
SEL[1:0], S_CLOCK, S_DATA,
S_LOAD, nP_LOAD, OE_REF
NA2, NB2, M1:M4, M6:M8
VCC = 3.465V,
VIN = 0V
-5
µA
NB0, NB1, NA0, NA1, M5,
OE_A, OE_B, VCO_SEL
VCC = 3.465V,
VIN = 0V
-150
µA
VCCO = 3.3V ± 5%
2.6
V
VCCO = 2.5V ± 5%
1.8
V
TEST; NOTE 1
VCCO = 3.3V ± 5%,
VCCO = 2.5V ± 5%
TEST; NOTE 1
0.5
V
NOTE 1: Output terminated with 50Ω to VCCO_REF/2.
TABLE 4C. DIFFERENTIAL DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, VCCO_A = VCCO_B = 3.3V±5% OR 2.5V±5%, TA = 0°C TO 70°C
Symbol
Parameter
Test Conditions
IIH
Input High Current
IIL
Input Low Current
VPP
Peak-to-Peak Input Voltage
Minimum
Typical
Units
nCLK
VIN = VCC = 3.465V
150
µA
CLK
VIN = VCC = 3.465V
150
µA
nCLK
VIN = 0V, VCC = 3.465V
CLK
VIN = 0V, VCC = 3.465V
-150
www.icst.com/products/hiperclocks.html
8
µA
-5
0.15
VCMR
Common Mode Input Voltage; NOTE 1, 2
VEE + 0.5
NOTE 1: For single ended applications, the maximum input voltage for CLK, nCLK is VCC + 0.3V.
NOTE 2: Common mode voltage is defined as VIH.
843034AY-01
Maximum
µA
1.3
V
VCC - 0.85
V
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TABLE 4D. LVPECL DC CHARACTERISTICS, VCCO_A = VCCO_B = 2.375V TO 3.465V, TA = 0°C TO 70°C
Symbol
Parameter
Maximum
Units
VOH
Output High Voltage; NOTE 1
Test Conditions
Minimum
VCCO - 1.4
Typical
VCCO - 0.9
V
V OL
Output Low Voltage; NOTE 1
VCCO - 2.0
VCCO - 1.7
V
VSWING
Peak-to-Peak Output Voltage Swing
0.6
1. 0
V
NOTE 1: Outputs terminated with 50 Ω to VCCO_x - 2V.
TABLE 5. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C
Symbol Parameter
fIN
Input
Frequency
Maximum
Units
XTAL_IN0, XTAL_OUT0
Test Conditions
Minimum
12
Typical
40
MHz
XTAL_IN1, XTAL_OUT1
12
40
MHz
50
MHz
S_CLOCK
Rise Time S_CLOCK, S_DATA, S_LOAD
6
ns
tR / tF
NOTE: For the input cr ystal, CLK/nCLK and TEST_CLK frequency range, the M value must be set for the VCO to operate
within the 490MHz to 640MHz range. Using the minimum input frequency of 12MHz, valid values of M are 41 ≤ M ≤ 53.
with input divider P = ÷1 (P_DIV = 00). Using the maximum frequency of 40MHz, valid values of M are 13 ≤ M ≤ 16.
TABLE 6. CRYSTAL CHARACTERISTICS
Parameter
Test Conditions
Minimum
Mode of Oscillation
Typical Maximum
Units
Fundamental
Frequency
12
40
MHz
Equivalent Series Resistance (ESR)
50
Ω
Shunt Capacitance
7
pF
Drive Level
1
mW
TABLE 7A. AC CHARACTERISTICS, VCC = VCCA = VCCO_A = VCCO_B = 3.3V±5%, TA = 0°C TO 70°C
Symbol Parameter
FOUT
t jit(Ø)
Test Conditions
Output Frequency
Phase Jitter, RMS (Random);
NOTE 1
t sk(o)
Output Skew; NOTE 2, 3
t R / tF
Output Rise/Fall Time
tS
Setup Time
tH
odc
Hold Time
Minimum
Typical
30.625
Integration Range:
637kHz - 5MHz
Measured @ the same
Output Frequency
20% to 80%
Units
640
MHz
0.61
ps
50
ps
200
700
ps
M, N to nP_LOAD
5
ns
S_DATA to S_CLOCK
5
ns
S_CLOCK to S_LOAD
5
ns
M, N to nP_LOAD
5
ns
S_DATA to S_CLOCK
5
ns
S_CLOCK to S_LOAD
5
ns
Output Duty Cycle
50
PLL Lock Time
tLOCK
See Parameter Measurement Information section.
NOTE 1: Please refer to the Phase Noise Plot.
NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions.
Measured at the output differential cross points.
NOTE 3: This parameter is defined in accordance with JEDEC Standard 65.
843034AY-01
Maximum
www.icst.com/products/hiperclocks.html
9
%
1
ms
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TABLE 7B. AC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, VCCO_A = VCCO_B = 2.5V±5%, TA = 0°C TO 70°C
Symbol Parameter
Test Conditions
tsk(o)
Output Frequency
Phase Jitter, RMS (Random);
NOTE 1
Output Skew; NOTE 2, 3
t R / tF
Output Rise/Fall Time
tS
Setup Time
FOUT
tjit(Ø)
tH
odc
Hold Time
Minimum
Typical
30.625
Integration Range:
637kHz - 5MHz
Maximum
Units
640
MHz
0.71
ps
50
20% to 80%
200
ps
700
ps
M, N to nP_LOAD
5
ns
S_DATA to S_CLOCK
5
ns
S_CLOCK to S_LOAD
5
ns
M, N to nP_LOAD
5
ns
S_DATA to S_CLOCK
5
ns
S_CLOCK to S_LOAD
5
ns
Output Duty Cycle
50
PLL Lock Time
tLOCK
See Parameter Measurement Information section.
NOTE 1: Please refer to the Phase Noise Plot.
NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions.
Measured at the output differential cross points.
NOTE 3: This parameter is defined in accordance with JEDEC Standard 65.
%
1
ms
TABLE 7C. AC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, VCCO_A = 3.3V±5%, VCCO_B = 2.5V±5%,TA = 0°C TO 70°C OR
VCC = VCCA = 3.3V±5%, VCCO_A = 2.5V±5%, VCCO_B = 3.3V±5%,TA = 0°C TO 70°C
Symbol Parameter
Test Conditions
t sk(o)
Output Frequency
Phase Jitter, RMS (Random);
NOTE 1
Output Skew; NOTE 2, 3
t R / tF
Output Rise/Fall Time
FOUT
t jit(Ø)
Minimum
Integration Range:
637kHz - 5MHz
20% to 80%
M, N to nP_LOAD
tS
tH
odc
Setup Time
Hold Time
Typical
35
Units
700
MHz
0.71
ps
50
ps
20 0
700
5
ps
ns
S_DATA to S_CLOCK
5
ns
S_CLOCK to S_LOAD
5
ns
M, N to nP_LOAD
5
ns
S_DATA to S_CLOCK
5
ns
S_CLOCK to S_LOAD
5
ns
Output Duty Cycle
50
PLL Lock Time
tLOCK
See Parameter Measurement Information section.
NOTE 1: Please refer to the Phase Noise Plot.
NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions.
Measured at the output differential cross points.
NOTE 3: This parameter is defined in accordance with JEDEC Standard 65.
843034AY-01
Maximum
www.icst.com/products/hiperclocks.html
10
%
1
ms
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TYPICAL PHASE NOISE AT 106.25MHZ
➤
0
-10
-20
Filter
106.25MHz
RMS Phase Jitter (Random)
637kHz to 5MHz = 0.61ps (typical)
-60
-70
-80
-90
-100
Raw Phase Noise Data
-110
-120
➤
NOISE POWER dBc
Hz
-30
-40
-50
-130
-140
➤
-150
-160
-170
-180
-190
100
1k
Phase Noise Result by adding
a Filter to raw data
10k
100k
1M
10M
100M
OFFSET FREQUENCY (HZ)
843034AY-01
www.icst.com/products/hiperclocks.html
11
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
PARAMETER MEASUREMENT INFORMATION
2V
2.8V±0.04V
2V
VCC ,
VCCA, VCCO_A,
VCCO_B
Qx
SCOPE
VCC ,
VCCA VCCO_A,
VCCO_B
LVPECL
Qx
SCOPE
LVPECL
VEE
nQx
nQx
VEE
-0.5V ± 0.125V
-1.3V ± 0.165V
3.3V CORE/2.5V OUTPUT LOAD AC TEST CIRCUIT
FOUTA0/nFOUTA0, FOUTB0/nFOUTB0
3.3V CORE/3.3V OUTPUT LOAD AC TEST CIRCUIT
FOUTA0/nFOUTA0, FOUTB0/nFOUTB0
2.05V±0.04V 1.25V±5%
1.65V±5%
SCOPE
VCC ,
VCCA,
VCCO_REF
VCC ,
VCCA
Qx
LVCMOS
SCOPE
VCCO_REF
Qx
LVCMOS
VEE
VEE
-1.65V ± 5%
-1.25V ± 5%
3.3V CORE/2.5V REF_CLK OUTPUT LOAD AC TEST CIRCUIT
3.3VCORE/3.3V REF_CLK OUTPUT LOAD AC TEST CIRCUIT
1σ contains 68.26% of all measurements
2σ contains 95.4% of all measurements
3σ contains 99.73% of all measurements
4σ contains 99.99366% of all measurements
6σ contains (100-1.973x10-7)% of all measurements
Reference Point
(Trigger Edge)
VOH
nFOUTx
VREF
FOUTx
VOL
nFOUTy
FOUTy
tsk(o)
Histogram
Mean Period
(First edge after trigger)
PERIOD JITTER
843034AY-01
OUTPUT SKEW
www.icst.com/products/hiperclocks.html
12
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
nFOUTA0
80%
FOUTA0
80%
VSW I N G
t PW
t
odc =
Clock
Outputs
PERIOD
t PW
20%
20%
tR
tF
x 100%
t PERIOD
OUTPUT RISE/FALL TIME
OUTPUT DUTY CYCLE/OUTPUT PULSE WIDTH/PERIOD
843034AY-01
www.icst.com/products/hiperclocks.html
13
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
APPLICATION INFORMATION
POWER SUPPLY FILTERING TECHNIQUES
As in any high speed analog circuitry, the power supply pins
are vulnerable to random noise. The ICS843034-01 provides
separate power supplies to isolate any high switching
noise from the outputs to the internal PLL. VCC, VCCA, and VCCO_x
should be individually connected to the power supply
plane through vias, and bypass capacitors should be
used for each pin. To achieve optimum jitter performance,
power supply isolation is required. Figure 2 illustrates how
a 24Ω resistor along with a 10μF and a .01μF bypass
capacitor should be connected to each VCCA pin.
3.3V
VCC
.01μF
24Ω
V CCA
.01μF
10 μF
FIGURE 2. POWER SUPPLY FILTERING
WIRING THE DIFFERENTIAL INPUT TO ACCEPT SINGLE ENDED LVCMOS/LVTTL LEVELS
Figure 3 shows how the differential input can be wired to accept
single ended levels. The reference voltage V_REF = VCC/2 is
generated by the bias resistors R1, R2 and C1. This bias circuit
should be located as close as possible to the input pin. The ratio
of R1 and R2 might need to be adjusted to position the V_REF in
the center of the input voltage swing. For example, if the input
clock swing is only 2.5V and VCC = 3.3V, V_REF should be 1.25V
and R2/R1 = 0.609.
VCC
R1
1K
Single Ended Clock Input
CLK
V_REF
nCLK
C1
0.1u
R2
1K
FIGURE 3. SINGLE ENDED SIGNAL DRIVING DIFFERENTIAL INPUT
843034AY-01
www.icst.com/products/hiperclocks.html
14
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
CRYSTAL INPUT INTERFACE
The ICS843034-01 has been characterized with 18pF parallel resonant crystals. The capacitor values, C1 and C2, shown
in Figure 4 below were determined using a 25MHz, 18pF
parallel resonant crystal and were chosen to minimize the
ppm error. The optimum C1 and C2 values can be slightly
adjusted for different board layouts.
XTAL_OUT
C1
22p
X1
18pF Parallel Crystal
XTAL_IN
C2
22p
ICS843034-01
ICS84332
Figure 4. CRYSTAL INPUt INTERFACE
DIFFERENTIAL CLOCK INPUT INTERFACE
The CLK /nCLK accepts LVDS, LVPECL, LVHSTL, SSTL, HCSL
and other differential signals. Both VSWING and VOH must meet the
VPP and VCMR input requirements. Figures 5A to 5D show interface examples for the HiPerClockS CLK/nCLK input driven by
the most common driver types. The input interfaces suggested
here are examples only. Please consult with the vendor of the
driver component to confirm the driver termination requirements.
For example in Figure 5A, the input termination applies for ICS
HiPerClockS LVHSTL drivers. If you are using an LVHSTL driver
from another vendor, use their termination recommendation.
3.3V
3.3V
3.3V
1.8V
Zo = 50 Ohm
CLK
Zo = 50 Ohm
CLK
Zo = 50 Ohm
nCLK
Zo = 50 Ohm
LVPECL
nCLK
HiPerClockS
Input
LVHSTL
ICS
HiPerClockS
LVHSTL Driver
R1
50
R1
50
HiPerClockS
Input
R2
50
R2
50
R3
50
FIGURE 5A. HIPERCLOCKS CLK/nCLK INPUT DRIVEN BY
ICS HIPERCLOCKS LVHSTL DRIVER
FIGURE 5B. HIPERCLOCKS CLK/nCLK INPUT DRIVEN BY
3.3V LVPECL DRIVER
3.3V
3.3V
3.3V
3.3V
3.3V
R3
125
R4
125
Zo = 50 Ohm
LVDS_Driv er
Zo = 50 Ohm
CLK
CLK
R1
100
Zo = 50 Ohm
nCLK
LVPECL
R1
84
HiPerClockS
Input
Receiv er
R2
84
FIGURE 5C. HIPERCLOCKS CLK/nCLK INPUT DRIVEN BY
3.3V LVPECL DRIVER
843034AY-01
nCLK
Zo = 50 Ohm
FIGURE 5D. HIPERCLOCKS CLK/nCLK INPUT DRIVEN BY
3.3V LVDS DRIVER
www.icst.com/products/hiperclocks.html
15
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TERMINATION FOR 3.3V LVPECL OUTPUT
drive 50Ω transmission lines. Matched impedance techniques
should be used to maximize operating frequency and minimize
signal distortion. Figures 6A and 6B show two different layouts
which are recommended only as guidelines. Other suitable clock
layouts may exist and it would be recommended that the board
designers simulate to guarantee compatibility across all printed
circuit and clock component process variations.
The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned
are recommended only as guidelines.
FOUTx and nFOUTx are low impedance follower outputs that
generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources
must be used for functionality. These outputs are designed to
3.3V
Zo = 50Ω
125Ω
FOUT
FIN
125Ω
Zo = 50Ω
Zo = 50Ω
FOUT
50Ω
1
RTT =
Z
((VOH + VOL) / (VCC – 2)) – 2 o
FIN
50Ω
Zo = 50Ω
VCC - 2V
RTT
84Ω
FIGURE 6A. LVPECL OUTPUT TERMINATION
84Ω
FIGURE 6B. LVPECL OUTPUT TERMINATION
RECOMMENDATIONS FOR UNUSED INPUT AND OUTPUT PINS
INPUTS:
OUTPUTS:
CRYSTAL INPUT:
For applications not requiring the use of the crystal oscillator
input, both XTAL_IN and XTAL_OUT can be left floating.
Though not required, but for additional protection, a 1kΩ
resistor can be tied from XTAL_IN to ground.
LVCMOS OUTPUT:
All unused LVCMOS output can be left floating. We
recommend that there is no trace attached.
LVPECL OUTPUT
All unused LVPECL outputs can be left floating. We
recommend that there is no trace attached. Both sides of the
differential output pair should either be left floating or
terminated.
CLK INPUT:
For applications not requiring the use of a clock input, it can
be left floating. Though not required, but for additional
protection, a 1kΩ resistor can be tied from the CLK input to
ground.
CLK/nCLK INPUT:
For applications not requiring the use of the differential input,
both CLK and nCLK can be left floating. Though not required,
but for additional protection, a 1kΩ resistor can be tied from
CLK to ground.
LVCMOS CONTROL PINS:
All control pins have internal pull-ups or pull-downs; additional
resistance is not required but can be added for additional
protection. A 1kΩ resistor can be used.
843034AY-01
www.icst.com/products/hiperclocks.html
16
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
TERMINATION
FOR
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
2.5V LVPECL OUTPUT
Figure 7A and Figure 7B show examples of termination for
2.5V LVPECL driver. These terminations are equivalent to terminating 50Ω to VCC - 2V. For VCC = 2.5V, the VCC - 2V is very
close to ground level. The R3 in Figure 7B can be eliminated
and the termination is shown in Figure 7C.
2.5V
2.5V
2.5V
VCCO=2.5V
VCCO=2.5V
R1
250
R3
250
Zo = 50 Ohm
Zo = 50 Ohm
+
+
Zo = 50 Ohm
Zo = 50 Ohm
-
-
2,5V LVPECL
Driv er
2,5V LVPECL
Driv er
R2
62.5
R1
50
R4
62.5
R2
50
R3
18
FIGURE 7B. 2.5V LVPECL DRIVER TERMINATION EXAMPLE
FIGURE 7A. 2.5V LVPECL DRIVER TERMINATION EXAMPLE
2.5V
VCCO=2.5V
Zo = 50 Ohm
+
Zo = 50 Ohm
2,5V LVPECL
Driv er
R1
50
R2
50
FIGURE 7C. 2.5V LVPECL TERMINATION EXAMPLE
843034AY-01
www.icst.com/products/hiperclocks.html
17
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
POWER CONSIDERATIONS
This section provides information on power dissipation and junction temperature for the ICS843034-01.
Equations and example calculations are also provided.
1. Power Dissipation.
The total power dissipation for the ICS843034-01 is the sum of the core power plus the power dissipated in the load(s).
The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results.
NOTE: Please refer to Section 3 for details on calculating power dissipated in the load.
•
•
Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 185mA = 641mW
Power (outputs)MAX = 30mW/Loaded Output pair
If all outputs are loaded, the total power is 2 * 30mW = 60mW
Total Power_MAX (3.465V, with all outputs switching) = 641mW + 60mW = 701mW
2. Junction Temperature.
Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the
device. The maximum recommended junction temperature for HiPerClockSTM devices is 125°C.
The equation for Tj is as follows: Tj = θJA * Pd_total + TA
Tj = Junction Temperature
θJA = Junction-to-Ambient Thermal Resistance
Pd_total = Total Device Power Dissipation (example calculation is in section 1 above)
TA = Ambient Temperature
In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a
moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 42.1°C/W per Table 8 below.
Therefore, Tj for an ambient temperature of 70°C with all outputs switching is:
70°C + 0.701W * 42.1°C/W = 99.5°C. This is well below the limit of 125°C.
This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow,
and the type of board (single layer or multi-layer).
TABLE 8. THERMAL RESISTANCE θJA
FOR
48-PIN LQFP, FORCED CONVECTION
θJA by Velocity (Linear Feet per Minute)
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
0
200
500
67.8°C/W
47.9°C/W
55.9°C/W
42.1°C/W
50.1°C/W
39.4°C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
843034AY-01
www.icst.com/products/hiperclocks.html
18
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
3. Calculations and Equations.
The purpose of this section is to derive the power dissipated into the load.
LVPECL output driver circuit and termination are shown in Figure 8.
VCCO
Q1
VOUT
RL
50
VCCO - 2V
FIGURE 8. LVPECL DRIVER CIRCUIT
TERMINATION
AND
To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination
voltage of V - 2V.
CCO
•
For logic high, VOUT = V
OH_MAX
(V
CCO_MAX
•
-V
OH_MAX
OL_MAX
CCO_MAX
-V
CCO_MAX
– 0.9V
) = 0.9V
For logic low, VOUT = V
(V
=V
=V
CCO_MAX
– 1.7V
) = 1.7V
OL_MAX
Pd_H is power dissipation when the output drives high.
Pd_L is the power dissipation when the output drives low.
Pd_H = [(V
OH_MAX
– (V
CCO_MAX
- 2V))/R ] * (V
CCO_MAX
L
-V
OH_MAX
) = [(2V - (V
CCO_MAX
-V
OH_MAX
))/R ] * (V
CCO_MAX
L
-V
)=
OH_MAX
[(2V - 0.9V)/50Ω] * 0.9V = 19.8mW
Pd_L = [(V
OL_MAX
– (V
CCO_MAX
- 2V))/R ] * (V
L
CCO_MAX
-V
OL_MAX
) = [(2V - (V
CCO_MAX
-V
OL_MAX
))/R ] * (V
L
CCO_MAX
-V
)=
OL_MAX
[(2V - 1.7V)/50Ω] * 1.7V = 10.2mW
Total Power Dissipation per output pair = Pd_H + Pd_L = 30mW
843034AY-01
www.icst.com/products/hiperclocks.html
19
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
RELIABILITY INFORMATION
TABLE 9. θJAVS. AIR FLOW TABLE
FOR
48 LEAD LQFP
θJA by Velocity (Linear Feet per Minute)
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
0
200
500
67.8°C/W
47.9°C/W
55.9°C/W
42.1°C/W
50.1°C/W
39.4°C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
TRANSISTOR COUNT
The transistor count for ICS843034-01 is: 5084
843034AY-01
www.icst.com/products/hiperclocks.html
20
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
PACKAGE OUTLINE - Y SUFFIX
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
FOR
48 LEAD LQFP
TABLE 10. PACKAGE DIMENSIONS
JEDEC VARIATION
ALL DIMENSIONS IN MILLIMETERS
SYMBOL
BBC
MINIMUM
NOMINAL
MAXIMUM
48
N
A
--
--
1.60
A1
0.05
--
0.15
A2
1.35
1.40
1.45
b
0.17
0.22
0.27
c
0.09
--
0.20
D
9.00 BASIC
D1
7.00 BASIC
D2
5.50 Ref.
E
9.00 BASIC
E1
7.00 BASIC
E2
5.50 Ref.
e
0.50 BASIC
L
0.45
0.60
0.75
θ
0°
--
7°
ccc
--
--
0.08
Reference Document: JEDEC Publication 95, MS-026
843034AY-01
www.icst.com/products/hiperclocks.html
21
REV. C NOVEMBER 28, 2005
PRELIMINARY
Integrated
Circuit
Systems, Inc.
ICS843034-01
FEMTOCLOCKS™
MULTI-RATE LVPECL FREQUENCY SYNTHESIZER
TABLE 11. ORDERING INFORMATION
Part/Order Number
Marking
Package
Shipping Packaging
Temperature
ICS843034AY-01
ICS843034A01
48 Lead LQFP
tray
0°C to 70°C
ICS843034AY-01T
ICS843034A01
48 Lead LQFP
1000 tape & reel
0°C to 70°C
ICS843034AY-01LF
ICS43034A01L
48 Lead "Lead-Free" LQFP
tray
0°C to 70°C
ICS843034AY-01LFT
ICS43034A01L
48 Lead "Lead-Free" LQFP
1000 tape & reel
0°C to 70°C
NOTE: Par ts that are ordred with an "LF" suffix to the par t number are the Pb-Free configuration and are RoHS compliant.
The aforementioned trademark, HiPerClockS™ and FEMTOCLOCKS™ is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use
or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use
in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are
not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS
product for use in life support devices or critical medical instruments.
843034AY-01
www.icst.com/products/hiperclocks.html
22
REV. C NOVEMBER 28, 2005
Similar pages