IDT IDT70V5378S166BGI 3.3v 64/32k x 18 synchronous fourport static ram Datasheet

3.3V 64/32K X 18
SYNCHRONOUS
FOURPORT™ STATIC RAM
Features
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
True four-ported memory cells which allow simultaneous
access of the same memory location
Synchronous Pipelined device
– 64/32K x 18 organization
Pipelined output mode allows fast 200MHz operation
High Bandwidth up to 14 Gbps (200MHz x 18 bits wide x
4 ports)
LVTTL I/O interface
High-speed clock to data access 3.0ns (max.)
3.3V Low operating power
Interrupt flags for message passing
Width and depth expansion capabilities
◆
◆
◆
◆
◆
◆
◆
◆
◆
IDT70V5388/78
Counter wrap-around control
– Internal mask register controls counter wrap-around
– Counter-Interrupt flags to indicate wrap-around
Counter readback on address lines
Mask register readback on address lines
Global Master reset for all ports
Dual Chip Enables on all ports for easy depth expansion
Separate upper-word and lower-word controls on all ports
272-BGA package (27mm x 27mm 1.27mm ball pitch) and
256-BGA package (17mm x 17mm 1.0mm ball pitch)
Commercial and Industrial temperature ranges
JTAG boundary scan
MBIST (Memory Built-In Self Test) controller
Port - 1 Logic Block Diagram(2)
R/WP1
0
1
1 /0
UBP1
CE0P1
CE1P1
LBP1
OEP1
I/O9P1 - I/O17P1
Port 1
I/O
Control
I/O0P1 - I/O8P1
TRST
TMS
TCK
TDI
CLKMBIST
Addr.
Read
Back
JTAG
Controller
TDO
MBIST
Port 1
Readback
Register
MRST
A0P1 - A15P1(1)
CNTRDP1
MKRDP1
MKLDP1
CNTINCP1
CNTLDP1
CNTRSTP1
CLKP1
MRST
CNTINT P1
Port 1
Mask
Register
,
Port 1
Address
Decode
Priority
Decision
Logic
64KX18
Memory
Array
Port 1
Counter/
Address
Register
R/WP1
CE0P1
CE1P1
CLK P1
MRST
NOTE:
1. A15x is a NC for IDT70V5378.
2. Port 2, Port 3, and Port 4 Logic Blocks are similar to Port 1 Logic Blocks.
Port 1
Interrupt
Logic
INTP1
5649 drw 01
AUGUST 2003
1
©2003 Integrated Device Technology, Inc.
DSC-5649/3
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Description
tions specially designed to facilitate system operations.
These include full-boundary, maskable address counters
with associated interrupts for each port, mailbox interrupt
flags on each port to facilitate inter-port communications,
Memory Built-In Self-Test (MBIST), JTAG support and an
asynchronous Master Reset to simplify device initialization. In addition, the address lines have been set up as I/O
pins, to permit the support of CNTRD (the ability to output the
current value of the internal address counter on the address
lines) and MKRD (the ability to output the current value of the
counter mask register). For specific details on the device
operation, please refer to the Functional Description and
subsequent explanatory sections, beginning on page 21.
The IDT70V5388/78 is a high-speed 64/32Kx18 bit
synchronous FourPort RAM. The memory array utilizes
FourPort memory cells to allow simultaneous access of
any address from all four ports. Registers on control, data,
and address inputs provide minimal setup and hold times.
The timing latitude provided by this approach allows systems to be designed with very short cycle times.
With an input data register and integrated burst
counters, the 70V5388/78 has been optimized for applications having unidirectional or bi-directional data flow in
bursts. An automatic power down feature, controlled by CE0
and CE1, permits the on-chip circuitry of each port to enter
a very low standby power mode.
The IDT70V5388/78 provides a wide range of func-
2
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Pin Configuration(4)
70V5388/78BG
BG-272(2)
272-Pin BGA
Top View(3)
09/25/02
1
2
3
4
5
6
7
8
9
10 11 12
13 14 15 16 17 18 19 20
A
LB
P1
I/O17
P2
I/O15
P2
I/O13
P2
I/O11
P2
I/O9
P2
I/O16
P1
I/O14
P1
I/O12
P1
I/O10
P1
I/O10
P4
I/O12
P4
I/O14
P4
I/O16
P4
I/O9
P3
I/O11
P3
I/O13
P3
I/O15
P3
I/O17
P3
LB
P4
A
B
VDD
UB
P1
I/O16
P2
I/O14
P2
I/O12
P2
I/O10
P2
I/O17
P1
I/O13
P1
I/O11
P1
TMS
TDI
I/O11
P4
I/O13
P4
I/O17
P4
I/O10
P3
I/O12
P3
I/O14
P3
I/O16
P3
UB
P4
VDD
B
C
A14
P1
A15(1)
P1
CE1
P1
CE0
P1
R/W
P1
I/O15
P1
VSS
VSS
I/O9
P1
TCK
TDO
I/O9
P4
V SS
VSS
I/O15
P4
R/W
P4
CE0
P4
CE1
P4
A15(1)
P4
A14
P4
C
D
VSS
A12
P1
A13
P1
OE
P1
VDD
VSS
VSS
VDD
VDD
VSS
VSS
VDD
VDD
VSS
VSS
VDD
OE
P4
A13
P4
A12
P4
VSS
D
E
A10
P1
A11
P1
A11
P4
A10
P4
E
F
A7
P1
A8
P1
A9
P1
CNTINT
P1
CNTINT
P4
A9
P4
A8
P4
A7
P4
F
G
VSS
A5
P1
A6
P1
CNTINC
P1
CNTINC
P4
A6
P4
A5
P4
VSS
G
H
A3
P1
A4
P1
A4
P4
A3
P4
H
J
VDD
A1
P1
A2
P1
VDD
GND
A1
P4
VDD
J
K
A0
P1
INT
P1
CNTRST
P1
CLK
P1
GND
CLK CNTRST INT
P4
P4
P4
A0
P4
K
L
A0
P2
INT
P2
CNTRST
VSS
P2
GND
CNTRST INT
P3
P3
A0
P3
L
M
VDD
A1
P2
CLK
P2
GND
A1
P3
VDD
M
N
A3
P2
A4
P2
CNTLD MKLD
P3
P3
A4
P3
A3
P3
N
P
VSS
A5
P2
A6
P2
CNTINC
P2
CNTINC
P3
A6
P3
A5
P3
VSS
P
R
A7
P2
A8
P2
A9
P2
CNTINT
P2
CNTINT
P3
A9
P3
A8
P3
A7
P3
R
T
A10
P2
A11
P2
A11
P3
A10
P3
T
U
VSS
A12
P2
A13
P2
OE
P2
VDD
VSS
VSS
VDD
VDD
VSS
VSS
VDD
VDD
VSS
VSS
VDD
OE
P3
A13
P3
A12
P3
VSS
U
V
A14
P2
A15(1)
P2
CE1
P2
CE 0
P2
R/W
P2
I/O6
P2
VSS
VSS
I/O0
P2
TRST
NC
I/O0
P3
VSS
VSS
I/O6
P3
R/W
P3
CE0
P3
CE1
P3
A15(1)
P3
A14
P3
V
W
VDD
UB
P2
I/O7
P1
I/O5
P1
I/O3
P1
I/O1
P1
I/O8
P2
I/O4
P2
I/O2
P2
MRST
CLKMBIST
I/O2
P3
I/O4
P3
I/O8
P3
I/O1
P4
I/O3
P4
I/O5
P4
I/O7
P4
UB
P3
VDD
W
LB
P2
I/O8
P1
I/O6
P1
I/O4
P1
I/O2
P1
I/O0
P1
I/O7
P2
I/O5
P2
I/O3
P2
I/O1
P2
I/O3
P3
I/O5
P3
I/O7
P3
I/O0
P4
I/O2
P4
I/O4
P4
I/O6
P4
I/O8
P4
LB
P3
Y
1
2
3
4
5
6
7
8
9
.
Y
MKRD CNTRD
P1
P1
CNTRD MKRD
P4
P4
MKLD CNTLD
P1
P1
A2
P2
CNTLD MKLD
P4
P4
(5)
GND
(5)
GND(5) GND(5) GND(5)
(5)
(5)
(5)
(5)
GND
(5)
GND
(5)
GND
(5)
GND
(5)
GND
GND(5)
VDD
(5)
GND
VSS
CLK
P3
(5)
GND
MKLD CNTLD
P2
P2
A2
P4
A2
P3
CNTRD MKRD
P3
P3
MKRD CNTRD
P2
P2
I/O1
P3
10 11 12
13 14 15 16 17 18 19 20
5649 drw 03
NOTES:
1. A15 x is a NC for IDT70V5378.
2. This package code is used to reference the package diagram.
3. This text does not indicate orientation of the actual part marking.
4. Package body is approximately 27mm x 27mm x 2.33mm, with 1.27mm ball-pitch.
5. Central balls are for thermal dissipation only. They are connected to device V SS.
3
6.42
,
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Pin Configuration(2)
70V5388/78BC
BC-256(3)
256-Pin BGA(4)
Top View
09/25/02
1
2
3
4
5
6
7
8
A
R/W
OE
LB
I/O16
I/O13
I/O9
I/O14
I/O10
P1
P1
P1
P2
P2
P2
P1
P1
B
A15(1)
CE1
UB
I/O17
I/O15
I/O11
P1
P1
P2
P2
P1
P1
C
A14
A13
CE0
I/O15
I/O12
P1
P1
P1
P2
P2
D
A10
A12
A11
A9
I/O11
P1
P1
P1
P1
P2
E
A7
A8
A6
A5
P1
P1
P1
P1
F
A3
A4
A2
A1
P1
P1
P1
P1
G
CLK
A0
P1
P1
H
VSS
CNTLD CNTRST CNTINT
INT
MKLD
P1
P1
J
CLK
CNTRST INT
K
P1
P2
P1
P2
CNTRD CNTINC
P1
P2
P1
P1
I/O14 I/O10
I/O17 I/O12
P1
P1
I/O16 I/O13
P1
P1
I/O9
P1
TMS
10
11
12 13 14
I/O9
I/O12
I/O16
I/O11
I/O15
I/O17
UB
CE1
P4
P4
P4
P3
P3
P3
P4
P4
I/O13 I/O17 I/O12
I/O16
LB
R/W
CE0
P4
P3
P4
P4
P4
TDO
I/O11
I/O14
OE
A15(1)
A14
P4
P4
P3
P3
P4
P4
P4
TCK
I/O10
I/O14
I/O9
I/O13
A11
A12
A13
P4
P4
P3
P3
P4
P4
P4
A6
A7
A8
A10
A9
P4
P4
P4
P4
P4
A1
A2
A3
A5
A4
P4
P4
P4
P4
P4
CNTLD CNTINC CNTRD
A0
CLK
P4
P4
P4
P4
VDD VDD
VSS
VSS
VSS
VDD
VDD
VDD VSS
VSS
VSS
VSS
VSS
VSS
P1
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS VSS
VSS
VSS
VSS VSS
VDD
VDD VSS
P1
CNTRD MKRD CNTINC CNTLD MKLD
VSS
P3
I/O15 I/O10
VDD VDD
VDD
15 16
TDI
VDD VDD VDD
VDD
CNTINT MKRD
P2
P2
9
P4
CNTRST MKRD
P4
VSS
P4
CNTRST
P3
P4
INT CNTINT MKLD
P4
P4
P3
P3
CNTLD CNTINC MKRD
A0
CNTRD
P3
P3
P3
P3
A1
A3
A4
A2
P3
P3
P3
P3
A5
A7
A8
A6
P3
P3
P3
P3
P2
P2
P2
P2
L
A3
A4
A2
A1
A0
P2
P2
P2
P2
P2
M
A8
A9
A7
A6
A5
P2
P2
P2
P2
P2
VDD
VDD
VDD VDD VDD
VDD
VDD
N
A11
A12
A10
I/O5
I/O1
I/O6
I/O2
I/O7
I/O2
A9
A11
A12
A10
P2
P2
P1
P1
P2
P2
TRST
I/O3
P2
P3
P3
P4
P3
P3
P3
P3
P
A13
A14
R/W
I/O7
I/O2
I/O7
I/O3
P2
P2
P2
P1
P1
P2
P2
R
A15(1)
CE1
UB
I/O8
I/O4
I/O0
P2
P2
P1
P1
P1
T
CE0
OE
LB
I/O6
I/O3
I/O8
P2
P2
P2
P1
P1
P2
3
4
P2
1
2
5
6
CLKMBIST
VSS VDD
VDD
MRST
I/O0
I/O4
I/O8
I/O3
I/O6
CE0
A14
A13
P3
P3
P3
P4
P4
P3
P3
P3
I/O5
I/O1
I/O2
I/O6
I/O1
I/O5
I/O7
UB
CE1
A15(1)
P2
P2
P3
P3
P4
P4
P4
P3
P3
P3
I/O4
I/O0
I/O1
I/O5
I/O0
I/O4
I/O8
LB
OE
R/W
P2
P2
P3
P3
P4
P4
P4
P3
P3
P3
7
8
9
10 11
D
E
F
G
H
CLK
P2
VSS
C
VSS
P3
P3
B
P4
INT CNTINT MKLD
P3
A
J
K
L
M
N
12 13 14 15 16
5649 drw 04
NOTES:
1. A15x is a NC for IDT70V5378.
2. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch.
3. This package code is used to reference the package diagram.
4. This text does not indicate orientation of the actual part-marking.
4
P
R
T
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Pin Definitions
Port 1
Port 2
Port 3
Port 4
Description
A0P1 - A15P1(1)
A0P2 - A15P2(1)
A0P3 - A15P3(1)
A0P4 - A15P4(1)
Address Inputs. In the CNTRD and MKRD operations, these pins serve
as outputs for the internal address counter and the internal counter mask
register respectively.
I/O0P1 - I/O17P1
I/O0P2 - I/O17P2
I/O0P3 - I/017P3
I/O0P4 - I/O17P4
Data Bus Input/Output.
CLKP1
CLKP2
CLKP3
CLKP4
Clock Input. The maximum clock input rate is fMAX. The clock signal can
be free running or strobed depending on system requirements.
Master Reset Input. MRST is an asycnchronous input, and affects all
ports. It must be asserted LOW (MRST = VIL) at initial power-up. Master
Reset sets the internal value of all address counters to zero, and sets
the counter mask registers for each port to 'unmasked'. It also resets the
output flags for the mailboxes and the counter interrupts (INT = CNTINT
= VIH) and deselects all registered control signals.
MRST
Chip Enable Inputs. To activate any port, both signals must be asserted
to their active states (CE0 = VIL, CE1 = VIH). A given port is disabled if
either chip enable is deasserted (CE0 = VIH and/or CE1 = VIL).
CE0P1, CE1P1
CE0P2, CE1P2
CE0P3, CE1P3
CE0P4, CE1P4
R/WPI
R/WP2
R/WP3
R/WP4
Read/Write Enable Input. This signal is asserted LOW (R/ W = VIL) in
order to write to the FourPort memory array, and it is asserted HIGH
(R/W = VIH) in order to read from the array.
LBP1
LBP2
LBP3
LBP4
Lower Byte Select Input (I/O0 - I/O8). Asserting this signal LOW (LB = VIL)
enables read/write operations to the lower byte. For read operations, this
signal is used in conjunction with OE in order to drive output data on the
lower byte of the data bus.
UBP1
UBP2
UBP3
UBP4
Upper Byte Select Input (I/O9 - I/O17). Asserting this signal LOW (LB =
VIL) enables read/write operations to the upper byte. For read
operations, this signal is used in conjunction with OE in order to drive
output data on the upper byte of the data bus.
OEP1
OEP2
OEP3
OEP4
Output Enable Input. Asserting this signal LOW (OE = VIL) enables the
device to drive data on the I/O pins during read operation. OE is an
asychronous input.
CNTLDP1
CNTLDP2
CNTLDP3
CNTLDP4
Counter Load Input. Asserting this signal LOW (CNTLD = VIL) loads the
address on the address lines (A 0 - A15(1)) into the internal address
counter for that port.
Counter Increment Input. Asserting this signal LOW (CNTINC = VIL)
increments the internal address counter for that port on each rising edge
of the clock signal. The counter will increment as defined by the counter
mask register for that port (default mode is to advance one address on
each clock cycle).
CNTINCP1
CNTINCP2
CNTINCP3
CNTINCP4
CNTRDP1
CNTRDP2
CNTRDP3
CNTRDP4
CNTRSTP1
CNTRSTP2
CNTRSTP3
CNTRSTP4
Counter Reset Input. Asserting this signal LOW (CNTRST = VIL) resets
the address counter for that port to zero.
CNTINTP1
CNTINTP2
CNTINTP3
CNTINTP4
Counter Interrupt Flag Output. This signal is asserted LOW (CNTINT =
VIL) when the internal address counter for that port 'wraps around' from
max address [(the counter will increment as defined by the counter mask
register for that port (default mode is to advance one address on each
clock cycle)] to address min. as the result of counter increment (CNTINT
= V IL). The signal goes LOW for one clock cycle, then automatically
resets.
Counter Readback Input. When asserted LOW (CNTRD = VIL) causes that
port to output the value of its internal address counter on the address
lines for that port. Counter readback is independent of the chip enables
for that port. If the port is activated (CE0 = VIL and CE1 = VIH), during the
counter readback operation, then the data bus will output the data
associated with that readback address in the FourPort memory array
(assuming that the byte enables and output enables are also asserted).
Truth Table III indicates the required states for all other counter controls
during this operation. The specific operation and timing of this funcion is
described in detail in the text.
5649 tbl 01
5
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Pin Definitions (con't.)
Port 1
Port 2
Port 3
Port 4
Description
Counter Mask Register Load Input. Asserting this signal LOW (MKLD =
VIL) loads the address on the address lines (A0 - A15(1)) into the counter
mask register for that port. Counter mask register operations are
described in detail in the text.
MKLDP1
MKLDP2
MKLDP3
MKLDP4
MKRDP1
MKRDP2
MKRDP3
MKRDP4
Counter Mask Register Readback Input. Asserting this signal LOW
(MKRD = VIL) causes that port to output the value of its internal counter
mask register on the address lines (A0 - A15(1)) for that port. Address
Counter and Counter-Mask Operational Table indicates the required
states for all other counter controls during this operation. Counter mask
register readback is independent of the chip enables for that port. If the
port is activated (CE0 = VIL and CE1 = VIH) during the counter mask
register readback operation, then the data bus will output the data
associated with that address in the FourPort memory array ( assuming
that the byte enables and output enables are also asserted). The specific
operation and timing of this function is described in detail in the text.
INTP1
INTP2
INTP3
INTP4
Interrupt Flag Output. The FourPort is equipped with mailbox functions:
each port has a specific address wthin the memory array which, when
written by any of the other ports, will generate an interrupt flag to that
port. The port clears its interrupt by reading that address. The memory
location is a valid address for data storage: a full 18-bit word can be
stored for recall by the target port or any other port. The mailbox
functions and associated interrupts are described in detail in the text.
TMS
JTAG Input: Test Mode Select
TRST
JTAG Input: Test Mode Reset (Intialize TAP Controller and reset the
MBIST Controller)
TCK
JTAG Input: Test Clock
TDI
JTAG Input: Test Data Input (serial)
TDO
JTAG Output: Test Data Output (serial)
CLKMBIST
MBIST Input: MBIST Clock
GND
Thermal Grounds (should be treated like V SS)
VDD
Core Power Supply (3.3V)
VSS
Electrical Grounds (0V)
5649 tbl 02
NOTE:
1. A15x is a NC for IDT70V5378.
6
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Truth Table I—Read/Write and Enable Control(1,2,3)
OE
CLK
CE0
CE 1
UB
LB
R/W
Upper Byte
I/O9-17
Lower Byte
I/O0-8
X
↑
H
X
X
X
X
High-Z
High-Z
Deselected–Power Down
X
↑
X
L
X
X
X
High-Z
High-Z
Deselected–Power Down
X
↑
L
H
H
H
X
High-Z
High-Z
All Bytes Deselected
X
↑
L
H
H
L
L
High-Z
DIN
Write to Lower Byte Only
X
↑
L
H
L
H
L
DIN
High-Z
Write to Upper Byte Only
X
↑
L
H
L
L
L
DIN
DIN
L
↑
L
H
H
L
H
High-Z
DOUT
Read Lower Byte Only
L
↑
L
H
L
H
H
DOUT
High-Z
Read Upper Byte Only
L
↑
L
H
L
L
H
DOUT
DOUT
Read Both Bytes
H
↑
X
X
X
X
X
High-Z
High-Z
Outputs Disabled
MODE
Write to Both Bytes
5649 tbl 03
NOTES:
1. "H" = V IH, "L" = VIL, "X" = Don't Care.
2. CNTLD, CNTINC, CNTRST = VIH.
3. OE is an asynchronous input signal.
Truth Table II—Address Counter & Mask Control(1,2)
External
Address
Previous
Internal
Address
Internal
Address
Used
CLK
X
X
0
↑
X
An
Ap
Ap
↑
X
An
X
An
↑
(3)
L
MODE
CNTRST
MKLD
I/O
X
L(3)
X
DI/O(0)
Counter Reset to Address 0
X
H
L
DI/O(p)
Counter disabled (Ap reused)
X
H
H
DI/O (n)
External Address Used
DI/O(p)
External Address Blocked—Counter disabled (Ap reused)
CNTLD CNTINC
An
Ap
Ap
↑
H
H
H
H
X
Ap
Ap + 1(5)
↑
H
L(4)
H
H
DI/O(p+1)(5) Counter Enabled—Internal Address generation
5649 tbl 04
NOTES:
1. "H" = VIH, "L" = VIL, "X" = Don't Care.
2. Read and write operations are controlled by the appropriate setting of R/W, CE0, CE 1, LB, UB and OE.
3. CNTLD and CNTRST are independent of all other memory control signals including CE 0, CE1 and LB, UB.
4. The address counter advances if CNTINC = VIL on the rising edge of CLK, regardless of all other memory control signals including CE0, CE1, LB, UB.
5. The counter will increment as defined by the counter mask register for that port (default mode is to advance one address on each clock cycle).
7
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Address Counter and Counter-Mask Control Operational Table
(Any Port)(1,2)
CLK
MRST
CNTRST
MKLD
CNTLD
CNTINC
CNTRD
MKRD
Mode
Operation
X
L
X
X
X
X
X
X
MasterReset
Counter/Address Register Reset and Mask Register
Set (resets chip as per reset state definition)
↑
H
L
X
X
X
X
X
Reset
Counter/Address Register Reset
↑
H
H
L
X
X
X
X
Load
Load of Address Lines into Mask Register
↑
H
H
H
L
X
X
X
Load
Load of Address Lines into Counter/Address
Register
↑
H
H
H
H
L
X
X
↑
H
X
X
X
X
L
X
Readback
↑
H
X
X
X
X
H
L
Readback
Readback Mask Register on Address Lines
↑
H
H
H(3)
H
H
X
X
Hold
Counter Hold
Increment Counter Increment
Readback Counter on Address Lines
5649 tbl 05
NOTES:
1. "X" = "don't care", "H" = VIH, "L" = VIL.
2. Counter operation and mask register operation is independent of Chip Enable.
3. MKLD = VIL will also hold the counter. Please refer to Truth Table II.
Recommended DC Operating
Conditions
Recommended Operating
Temperature and Supply Voltage(1)
Grade
Commercial
Industrial
Ambient
Temperature
GND
VDD
0OC to +70OC
0V
3.3V + 150mV
-40OC to +85OC
0V
3.3V + 150mV
Symbol
VDD
VSS
5649 tbl 06
NOTES:
1. This is the parameter TA. This is the "instant on" case temperature.
Parameter
Supply Voltage
Ground
V IH
Input High Voltage
(Address, Control & I/O Inputs)
VIL
Input Low Voltage
Min.
Typ.
Max.
Unit
3.15
3.3
3.45
V
0
0
0
2.0
____
-0.3(1)
____
VDD + 150mV
V
(2)
0.8
V
V
5649 tbl 07
NOTES:
1. Undershoot of VIL > -1.5V for pulse width less than 10ns is allowed.
2. VTERM must not exceed VDD + 150mV.
8
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Capacitance(1)
Absolute Maximum Ratings(1)
Symbol
Rating
Commercial
& Industrial
Unit
Symbol
VTERM(2)
Terminal Voltage
with Respect to GND
-0.5 to +4.6
V
TBIAS(3)
Temperature Under Bias
-55 to +125
o
TSTG
Storage Temperature
-65 to +150
o
C
TJN
Junction Temperature
+150
o
C
IOUT
DC Output Current
50
(TA = +25°C, F = 1.0MHZ)
CIN
COUT(3)
C
Parameter
Input Capacitance
Output Capacitance
Conditions(2)
Max.
Unit
VIN = 3dV
8
pF
VOUT = 3dV
10.5
pF
5649 tbl 09
NOTES:
1. These parameters are determined by device characterization, but are not
production tested.
2. 3dV references the interpolated capacitance when the input and output switch
from 0V to 3V or from 3V to 0V.
3. COUT also references CI/O.
mA
5623 tbl 06
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. VTERM must not exceed VDD + 150mV for more than 25% of the cycle time or
4ns maximum, and is limited to < 20mA for the period of VTERM > VDD + 150mV.
3. Ambient Temperature under DC Bias. No AC conditions. Chip Deselected.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 3.3V ± 150mV)
70V5388/78S
Symbol
|ILI|
|ILI|
Parameter
Input Leakage Current
Test Conditions
(1)
(1,2)
JTAG Input Leakage Current
(1)
Min.
Max.
Unit
VDD = Max., VIN = 0V to VDD
___
10
µA
VDD = Max., VIN = 0V to VDD
___
30
µA
|ILO |
Output Leakage Current
VOUT = 0V to V DD, Outputs in tri-state mode
___
10
µA
VOL
Output Low Voltage
IOL = +4mA, VDD = Min.
___
0.4
V
VOH
Output High Voltage
IOH = -4mA, VDD = Min.
2.4
___
V
5649 tbl 10
NOTE:
1. At VDD < 2.0V leakages are undefined.
2. Applicable only for TMS, TDI and TRST inputs.
9
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(3) (VDD = 3.3V ± 150mV)
70V5388/78S200 70V5388/78S166 70V5388/78S133 70V5388/78S100
Com'l Only
Com'l
Com'l
Com'l
& Ind
& Ind
& Ind
Symbol
IDD
ISB1
ISB2
ISB3
ISB4
Parameter
Test Condition
Version
Typ.(4)
Max.
Typ.(4)
Max.
Typ.(4)
Max.
Typ.(4)
Max.
Dynamic Operating
Current (All
Ports Active)
CE1 = CE2 = CE3 = CE4(5) = VIL,
Outputs Disabled,
f = fMAX(1)
COM'L
S
405
470
340
395
275
320
205
240
IND
S
___
___
340
400
275
325
205
245
Standby Current
(All Ports - TTL
Level Inputs)
CE1 = CE2 = CE3 = CE4(5) = VIH,
Outputs Disabled,
f = fMAX(1)
COM'L
S
195
225
160
190
130
155
100
120
IND
S
___
___
160
195
130
160
100
125
Standby Current
(One Port - TTL
Level Inputs)
CEA = VIL and CEB = CEC = CED = VIH(5)
Active Port, Outputs Disabled,
f=fMAX(1)
COM'L
S
250
290
210
240
170
195
130
150
IND
S
___
___
210
245
170
200
130
155
COM'L
S
1.5
15
1.5
15
1.5
15
1.5
15
IND
S
___
___
1.5
15
1.5
15
1.5
15
COM'L
S
250
290
210
240
170
195
130
150
IND
S
___
___
210
245
170
200
130
155
Full Standby Current (All All Ports Outputs Disabled,
Ports - CMOS
CE(5) > VDD - 0.2V, VIN > VDD - 0.2V
Level Inputs)
or VIN < 0.2V, f = 0(2)
Full Standby Current
(One Port - CMOS
Level Inputs)
CEA < 0.2V and CEB = CEC = CED > VDD - 0.2V(5)
VIN > VDD - 0.2V or VIN < 0.2V
Active Port, Outputs Disabled, f = fMAX(1)
Unit
mA
mA
mA
mA
mA
5649 tbl 11
NOTES:
1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency clock cycle of 1/tCYC, using "AC TEST CONDITIONS" at input
levels of GND to 3V.
2. f = 0 means no address, clock, or control lines change. Applies only to input at CMOS level standby.
3. Parameters are identical for all ports.
4. VDD = 3.3V, TA = 25°C for Typ, and are not production tested. IDD DC(f=0) = 120mA (Typ).
5. CEX = VIL means CE0X = VIL and CE1X = VIH
CEX = VIH means CE0X = VIH or CE1X = V IL
CEX < 0.2V means CE0X < 0.2V and CE1X > VDD - 0.2V
CEX > VDD - 0.2V means CE0X > VDD - 0.2V or CE1X - 0.2V
"X" represents indicator for appropriate port.
10
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
AC Test Conditions (VDDQ - 3.3V)
Input Pulse Levels (Address & Controls)
GND to 3.0V
Input Pulse Levels (I/Os)
GND to 3.0V
Input Rise/Fall Times
2ns
Input Timing Reference Levels
1.5V
Output Reference Levels
1.5V
Output Load
Figure 1
5649 tbl 12
50Ω
50Ω
DATAOUT
1.5V
10pF
(Tester)
5649 drw 05
Figure 1. AC Output Test Load
*(For tLZ , tHZ, tWZ, tOW)
7
6
∆ tCD
5
(Typical, ns)
4
3
2
1
0
0
20
40
60
80
100
120
∆ Capacitance (pF) from AC Test Load
140
5649 drw 07
Figure 2. Typical Output Derating (Lumped Capacitive Load).
11
6.42
160
,
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the Operating Temperature Range
(Read and Write Cycle Timing) (VDD = 3.3V ± 150mV, TA = 0°C to +70°C)
Symbol
Parameter
70V5388/78S200
Com'l Only
70V5388/78S166
Com'l
& Ind
70V5388/78S133
Com'l
& Ind
70V5388/78S100
Com'l
& Ind
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
____
200
____
166
____
133
____
100
MHz
fMAX2
Maximum Frequency
tCYC2
Clock Cycle Time
5
____
6
____
7.5
____
10
____
ns
tCH2
Clock HIGH Time
2.0
____
2.1
____
2.6
____
4
____
ns
tCL2
Clock LOW Time
2.0
____
2.1
____
2.6
____
4
____
ns
tSA
Address Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHA
Address Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSC
Chip Enable Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHC
Chip Enable Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSW
R/W Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHW
R/W Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSD
Input Data Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHD
Input Data Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSB
Byte Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHB
Byte Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSCLD
CNTLD Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHCLD
CNTLD Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSCINC
CNTINC Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHCINC
CNTINC Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSCRST
CNTRST Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHCRST
CNTRST Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
ns
CNTRD Setup Time
1.5
____
1.7
____
1.8
____
2
____
tHCRD
CNTRD Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSMLD
MKLD Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHMLD
MKLD Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tSMRD
MKRD Setup Time
1.5
____
1.7
____
1.8
____
2
____
ns
tHMRD
MKRD Hold Time
0.5
____
0.5
____
0.5
____
0.7
____
ns
tOE
Output Enable to Data Valid
____
4.0
____
4.0
____
4.2
____
5
ns
tOLZ (1,5)
OE to LOW-Z
1
____
1
____
1
____
1
____
ns
tOHZ (1,5)
OE to HIGH-Z
tCD2
tSCRD
1
3.4
1
3.6
1
4.2
1
4.5
ns
Clock to Data Valid
____
3.0
____
3.2
____
3.4
____
3.6
ns
tCA2
Clock to Counter Address Readback Valid
____
3.4
____
3.6
____
4.2
____
5
ns
tCM2
Clock to Mask Register Readback Valid
____
3.4
____
3.6
____
4.2
____
5
ns
tDC
____
1
____
1
____
1
____
ns
ns
Data Output Hold After Clock HIGH
1
tCKHZ
(1,2,5)
Clock HIGH to Output HIGH-Z
1
3
1
3
1
3
1
3
tCKLZ
(1,2,5)
Clock HIGH to Output LOW-Z
1
____
1
____
1
____
1
____
ns
5649 tbl 13a
12
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the Operating Temperature Range
(Read and Write Cycle Timing) (VDD = 3.3V ± 150mV, TA = 0°C to +70°C)
Symbol
Parameter
70V5388/78S133
Com'l
& Ind
70V5388/78S100
Com'l
& Ind
70V5388/78S200
Com'l Only
70V5388/78S166
Com'l
& Ind
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
Interrupt Timing
tSINT
Clock to INT Set Time
____
5
____
6
____
7.5
____
10
ns
tRINT
Clock to INT Reset Time
____
5
____
6
____
7.5
____
10
ns
tSCINT
Clock to CNTINT Set Time
____
5
____
6
____
7.5
____
10
ns
tRCINT
Clock to CNTINT Reset Time
____
5
____
6
____
7.5
____
10
ns
Master Reset Timing
tRS
Master Reset Pulse Width
7.5
____
7.5
____
7.5
____
10
____
ns
tRSR
Master Reset Recovery Time
7.5
____
7.5
____
7.5
____
10
____
ns
tROF
Master Reset to Output Flags Reset Time
____
6.5
____
6.5
____
6.5
____
8
ns
Clock-to-Clock Setup Time
4.5
____
5
____
6.5
____
9
____
ns
fJTAG
Maximum JTAG TAP Controller Frequency
____
10
____
10
____
10
____
10
MHz
tTCYC
TCK Clock Cycle Time
100
____
100
____
100
____
100
____
ns
tTH
TCK Clock High Time
40
____
40
____
40
____
40
____
ns
tTL
TCK Clock Low Time
40
____
40
____
40
____
40
____
ns
tJS
JTAG Setup
20
____
20
____
20
____
20
____
ns
tJH
JTAG Hold
20
____
20
____
20
____
20
____
ns
tJCD
TCK Clock Low to TDO Valid (JTAG Data Output)
____
20
____
20
____
20
____
20
ns
tJDC
TCK Clock Low to TDO Invalid (JTAG Data Output Hold)
0
____
0
____
0
____
0
____
ns
fBIST
Maximum CLKMBIST Frequency
____
200
____
166
____
133
____
100
MHz
____
2.5
____
3
____
4
____
ns
Port to Port Delays
tCCS (3)
JTAG Timing(4)
CLKMBIST High Time
2
tBL
CLKMBIST Low Time
2
____
2.5
____
3
____
4
____
ns
tJRST
JTAG Reset
50
____
50
____
50
____
50
____
ns
tJRSR
JTAG Reset Recovery
50
____
50
____
50
____
50
____
ns
tBH
5649 tbl 13b
NOTES:
1. Guaranteed by design (not production tested).
2. Valid for both data and address outputs.
3. This parameter defines the time necessary for one port to complete a write and have valid data available at that address for access from the other port(s).
Attempting to read data before t CCS has elapsed will result in the output of indeterminate data.
4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet.
5. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 1).
13
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Switching Waveforms
Timing Waveform of Read Cycle(2)
tCYC2
tCH2
tCL2
CLK
CE0
tSC
tSC
tHC
tHC
(3)
CE1
tSB
tSB
tHB
LB, UB
R/W
ADDRESS
tSW
tHW
tSA
tHA
(4)
An
An + 1
(1 Latency)
An + 2
An + 3
tDC
tCD2
DATAOUT
Qn
tCKLZ
OE
tHB
(5)
Qn + 1
Qn + 2
(5)
(1)
tOHZ
tOLZ
(1)
tOE
NOTES:
1. OE is asynchronously controlled; all other inputs are synchronous to the rising clock edge.
5649 drw 08
2. CNTLD = VIL, CNTINC and CNTRST = VIH.
3. The output is disabled (High-Impedance state) by CE 0 = VIH, CE1 = V IL, LB, UB = VIH following the next rising edge of the clock. Refer to Truth Table I.
4. Addresses do not have to be accessed sequentially since CNTLD = VIL constantly loads the address on the rising edge of the CLK; numbers
are for reference use only.
5. If LB, UB was HIGH, then the appropriate Byte of DATAOUT for Qn + 2 would be disabled (High-Impedance state).
,
Timing Waveform of a Multi-Device Read(1,2)
tCH2
tCYC2
tCL2
CLK
tSA
tHA
A0
ADDRESS(B1)
tSC
tHC
CE0(B1)
tSC
tHC
tCD2
tCD2
Q0
DATAOUT(B1)
tCKHZ
A1
tSC
tCKHZ
A6
A5
A4
A3
A2
tSC
CE0(B2)
Q3
tCKLZ
tDC
tHA
A0
ADDRESS(B2)
tCD2
Q1
tDC
tSA
A6
A5
A4
A3
A2
A1
tHC
tHC
tCD2
tCKHZ
tCD2
,
DATAOUT(B2)
Q4
Q2
tCKLZ
NOTES:
1. B1 Represents Device #1; B2 Represents Device #2. Each Device consists of one IDT70V5388/78 for this waveform,
and are setup for depth expansion in this example. ADDRESS(B1) = ADDRESS(B2) in this situation.
2. LB, UB, OE, and CNTLD = VIL; CE 1(B1), CE1(B2) , R/W, CNTINC, and CNTRST = VIH.
14
tCKLZ
5649 drw 09
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Port A Write to Port B Read(1,2,4)
CLK"A"
tSW
tHW
tSA
tHA
R/W"A"
ADDRESS"A"
NO
MATCH
MATCH
tSD
DATAIN"A"
tHD
VALID
tCCS(3)
CLK"B"
tCD2
R/W"B"
ADDRESS"B"
tSW
tHW
tSA
tHA
NO
MATCH
MATCH
DATAOUT"B"
VALID
tDC
5649 drw 10
NOTES:
1. CE 0, LB, UB, and CNTLD = VIL; CE1, CNTINC, CNTRST, MRST, MKLD, MKRD and CNTRD = VIH.
2. OE = VIL for Port "B", which is being read from. OE = VIH for Port "A", which is being written to.
3. If t CCS < minimum specified, then data from Port "B" read is not valid until following Port "B" clock cycle (ie, time from write to valid read on opposite
port will be tCCS + 2 tCYC2 + tCD2). If tCCS > minimum, then data from Port "B" read is available on first Port "B" clock cycle (ie, time from write to
valid read on opposite port will be tCCS + tCYC2 + tCD2).
4. All timing is the same for all ports. Port "A" may be any port. Port "B" is any other port on the device.
Timing Waveform of Read-to-Write-to-Read (OE = VIL)(2)
tCYC2
tCH2
tCL2
CLK
CE0
tSC
tHC
tSB
tHB
CE1
LB, UB
tSW tHW
R/W
(3)
ADDRESS
tSW tHW
An
tSA tHA
An +1
An + 2
An + 3
An + 2
An + 4
tSD tHD
DATAIN
Dn + 2
(1)
tCD2
tCD2
tCKHZ
Qn
DATAOUT
READ
Qn + 3
tCKLZ
(4)
NOP
WRITE
READ
5649 drw 11
NOTES:
1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals.
2. CNTLD = VIL; CNTINC, and CNTRST, MRST, MKLD, MKRD and CNTRD = VIH. "NOP" is "No Operation".
3. Addresses do not have to be accessed sequentially since CNTLD = VIL constantly loads the address on the rising edge of the CLK; numbers
are for reference use only.
4. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity.
15
6.42
,
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Read-to-Write-to-Read ( OE Controlled)(2)
tCH2
tCYC2
tCL2
CLK
CE0
tSC
tHC
tSB
tHB
CE1
LB, UB
tSW tHW
R/W
(3)
ADDRESS
tSW tHW
An
tSA tHA
An +1
An + 2
tSD
DATAIN
Dn + 2
tCD2
(1)
Qn
DATAOUT
An + 4
An + 3
An + 5
tHD
Dn + 3
tCD2
(4)
Qn + 4
tCKLZ
tOHZ
OE
READ
WRITE
READ
5649 drw 12
,
NOTES:
1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals.
2. CNTLD = VIL; CNTINC, CNTRST, MRST, MKLD, MKRD and CNTRD = VIH.
3. Addresses do not have to be accessed sequentially since CNTLD = VIL constantly loads the address on the rising edge of the CLK;
numbers are for reference use only.
4. This timing does not meet requirements for fastest speed grade. This waveform indicates how logically it could be done if timing so allows.
Timing Waveform of Read with Address Counter Advance(1)
tCH2
tCYC2
tCL2
CLK
tSA
ADDRESS
tHA
An
tSCLD tHCLD
CNTLD
tSCLD tHCLD
CNTINC
tSCLD tHCLD
tCD2
DATAOUT
Qx - 1(2)
,
Qn + 2(2)
Qn + 1
Qn
Qx
Qn + 3
tDC
READ
EXTERNAL
ADDRESS
READ WITH COUNTER
COUNTER
HOLD
READ
WITH
COUNTER
5649 drw 13
NOTES:
1. CE0, LB and UB = VIL; CE1, CNTRST, MRST, MKLD, MKRD and CNTRD = VIH.
2. If there is no address change via CNTLD = V IL (loading a new address) or CNTINC = VIL (advancing the address), i.e. CNTLD = VIH and CNTINC = V IH, then
the data output remains constant for subsequent clocks.
16
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Write with Address Counter Advance(1)
tCH2
tCYC2
tCL2
CLK
tSA
tHA
An
ADDRESS
INTERNAL(3)
ADDRESS
An(7)
An + 2
An + 1
An + 4
An + 3
tSCLD tHCLD
CNTLD
tSCINC tHCINC
CNTINC
tSD tHD
Dn + 1
Dn
DATAIN
WRITE
EXTERNAL
ADDRESS
Dn + 1
Dn + 4
Dn + 3
Dn + 2
WRITE
WRITE
WITH COUNTER COUNTER HOLD
WRITE WITH COUNTER
5649 drw 14
Timing Waveform of Counter Reset(2)
tCH2
tCYC2
tCL2
CLK
tSA tHA
(4)
An
ADDRESS
INTERNAL(3)
ADDRESS
Ax
A1
A0
An + 2
An + 1
An
An + 1
tSW tHW
R/W
CNTLD
tSCLD tHCLD
CNTINC
tSCRST tHCRST
CNTRST
tSCINC tHCINC
tSD
tHD
D0
DATAIN
(5)
Q1
Q0
DATAOUT
EXECUTE
CNTRST
(6)
WRITE
A0
READ
A0
READ
A1
READ
ADDRESS n
Qn
READ
ADDRESS n+1
5649 drw 15
NOTES:
1. CE 0, LB, UB, and R/W = VIL; CE1 and CNTRST, MRST, MKLD, MKRD, and CNTRD = vIH.
2. CE 0, LB, UB = VIL; CE1 = VIH.
3. The "Internal Address" is equal to the "External Address" when CNTLD = VIL and equals the counter value when CNTLD = VIH.
4. Addresses do not have to be accessed sequentially since CNTLD = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference
use only.
5. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals.
6. No dead cycle exists during CNTRST operation. A READ or WRITE cycle may be coincidental with the counter CNTRST cycle: Address 0000h will be
accessed. Extra cycles are shown here simply for clarification. For more information on CNTRST function refer to Truth Table II.
7. CNTINC = V IL advances Internal Address from ‘An’ to ‘An +1’. The transition shown indicates the time required for the counter to advance. The ‘An +1’Address
is written to during this cycle.
17
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Master Reset(1)
tCYC2
tCH2
tCL2
CLK
tRS
MRST
tROF
ALL ADDRESS/
DATA LINES
tRSR
tS(2)
ALL OTHER
INPUTS
INACTIVE
ACTIVE
CNTINT
INT
5649 drw 16
NOTES:
1. Master Reset will reset the device. For JTAG and MBIST reset please refer to the JTAG Timing specification.
2. tS is the set-up time required for all input control signals.
18
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Load and Read Address Counter(1,2,3)
tCYC2
tCH2
tCL2
(2)
(3)
CLK
tSA
tCA2
tCKLZ
tHA
tCKHZ
An+2(4)
An
A0 - A15
tSCLD
tHCLD
CNTLD
CNTINC
tSCINC
tHCINC
tHCRD
tSCRD
CNTRD
INTERNAL
ADDRESS
An+1
An
tCD2
DATAOUT
Qx
Qx-1
LOAD
EXTERNAL
ADDRESS
An+2
An+2
An+2
,
tDC
Qn+1
Qn
Qn+2
Qn+2
Qn+2
READ
INTERNAL
ADDRESS
READ DATA WITH COUNTER
5649 drw 17
NOTES:
1. CE0, OE, LB and UB = VIL; CE1, R/W, CNTRST, MRST, MKLD and MKRD = VIH.
2. Address in output mode. Host must not be driving address bus after time tCKLZ in next clock cycle.
3. Address in input mode. Host can drive address bus after tCKHZ.
4. This is the value of the address counter being read out on the address lines.
Timing Waveform of Load and Read Mask Register(1,2,3,4)
tCYC2
tCH2
tCL2
(2)
(1)
CLK
tSA
A0 - A15
tHA
tCKLZ
tCA2
tCKHZ
An(4)
An
tSMLD
tHMLD
MKLD
tSMRD
tHMLD
MKRD
MASK
INTERNAL
VALUE
An
An
An
An
An
An
READ
MASK-REGISTER
VALUE
LOAD
MASK REGISTER
VALUE
5649 drw 18
NOTES:
1. Address in output mode. Host must not be driving address bus after time tCKLZ in next clock cycle.
2. Address in input mode. Host can drive address bus after tCKHZ.
3. CE0, OE, LB and UB = VIL; CE1, R/W, CNTRST, MRST, CNTLD, CNTRD and CNTINC = V IH.
4. This is the value of the mask register being read out on the address lines.
19
6.42
,
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Counter Interrupt(1,3)
tCYC2
tCH2
tCL2
CLK
EXTERNAL
ADDRESS
007Fh
tSMLD
xx7Dh
tHMLD
MKLD
tSCLD
tHCLD
CNTLD
tSCINC
tHCINC
CNTINC
COUNTER
INTERNAL
ADDRESS
An
xx7Eh
xx7Dh
xx7Fh
xx00h
xx00h
,
tRCINT
tSCINT
(2)
CNTINT
5649 drw 19
Timing Waveform of Mailbox Interrupt Timing(4,6)
tCYC2
tCH2 tCL2
CLKP1
tSA tHA
PORT-1
ADDRESS
INTP2
FFFE
An
(5)
An+1
An+2
An+3
tSINT
(7)
tRINT
tCYC2
tCH2 tCL2
CLKP2
tSA tHA
PORT-2
ADDRESS
Am
Am+1
FFFE
(5)
Am+3
Am+4
5649 drw 20
,
NOTES:
1. CE0, OE, LB and UB = VIL; CE1, R/W, CNTRST, MRST, CNTRD and MKRD = VIH.
2. CNTINT is always driven.
3. CNTINT goes LOW as the counter address increments (via CNTINC = VIL) past the maximum value programmed into the mask register and 'wraps around' to xx00h
CNTINT stays LOW for one cycle, then resets. In this example, the mask register was programmed at xx7Fh ('x' indicates "Don't Care"). The Counter Mask Register
operations are detailed on page 24.
4. CNTRST, MRST, CNTRD CNTINC , MKRD and MKLD = V IH. The mailbox interrupt circuitry relies on the state of the chip enables, the read/write signal, and the
address location to generate or clear interrupts as appropriate - other control signals such as OE, LB and UB are "Don't Care". Please refer to Truth Table III (page
22) for further explanation.
5. Address FFFEh is the mailbox location for Port 2 of IDT70V5388. Refer to Truth Table III for mailbox location of other Ports (page 22).
6. Port 1 is configured for a write operation (setting the interrupt) in this example, and Port 2 is configured for a read operation (clearing the interrupt). Ports 1 and 2 are
used for an example: any port can set an interrupt to any other port per the operations in Truth Table III (page 22).
7. The interrupt flag is always set with respect to the rising edge of the writing port's clock, and cleared with respect to the rising edge of the reading port's clock.
20
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Functional Description
The IDT70V5388/78 provides a true synchronous
FourPort Static RAM interface. Registered inputs provide
minimal set-up and hold times on address, data, and all
critical control inputs. All internal registers are clocked on
the rising edge of the clock signal, however, the self-timed
internal write pulse is independent of the LOW to HIGH
transition of the clock signal and the duration of the R/W
input signal. This is done in order to offer the fastest
possible cycle times and highest data throughput. At 200
MHz, the device supports a cycle time of 5 ns, and provides
a pipelined data output of 3.0 ns from clock edge to data
valid. Four ports operating at 200 MHz, each with a bus
width of 18 bits, results in a data throughput rate of nearly
14 Gbps.
As a true synchronous device, the IDT70V5388/78
provides the flexibility to clock each port independently: the
ports may run at different frequencies and/or out of synchronization with each other. As a true FourPort device, the
IDT70V5388/78 is capable of performing simultaneous
reads from all ports on the same address location. Care
should be taken when attempting to write and read address
locations simultaneously: the timing diagrams depict the
critical parameter tCCS, which determines the amount of
time needed to ensure that the write has successfully been
completed and so valid data is available for output. Violation
of tCCS may produce indeterminate data for the read. Two or
more ports attempting to write the same address location
simultaneously will result in indeterminate data recorded at
that address.
Each port is equipped with dual chip enables, CE0
and CE1. A HIGH on CE0 or a LOW on CE1 for one clock
cycle on any port will power down the internal circuitry on
that port in order to reduce static power consumption. The
multiple chip enables also allow easier banking of multiple
IDT70V5388/78s for depth expansion configurations. One
cycle is required with chip enables reasserted to reactivate
the outputs.
Depth and Width Expansion
The IDT70V5388/78 features dual chip enables
(refer to Truth Table I) in order to facilitate rapid and simple
depth expansion with no requirements for external logic.
Figure 4 illustrates how to control the various chip enables
in order to expand two devices in depth.
The IDT70V5388/78 can also be used in applications requiring expanded width, as indicated in Figure 3.
Through combining the control signals, the devices can be
grouped as necessary to accommodate applications requiring 36-bits or wider.
A16/A15(1)
IDT70V5388/78
CE0
CE1
IDT70V5388/78
CE1
VDD
VDD
Control Inputs
Control Inputs
IDT70V5388/78
CE0
IDT70V5388/78
CE1
CE1
CE0
CE0
Control Inputs
Control Inputs
UB, LB
R/W,
OE,
CLK,
CNTLD,
CNTRST,
CNTINC
5649 drw 21
Figure 3. Depth and Width Expansion with IDT70V5388/78
NOTE:
1. A16 is for IDT70V5388, A15 is for IDT70V5378.
21
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Mailbox Interrupts
The IDT70V5388/78 supports mailbox interrupts,
facilitating communication among the devices attached to
each port. If the user chooses the interrupt function, then
each of the upper four address locations in the memory
array are assigned as a mailbox for one of the ports: FFFFh
(7FFFh for IDT70V5378) is the mailbox for Port 1, FFFEh
(7FFEh for IDT70V5378) is the mailbox for Port 2, FFFDh
(7FFDh for IDT70V5378) is the mailbox for Port 3, and
FFFCh (7FFCh for IDT70V5378) is the mailbox for Port 4.
Truth Table III details the operation of the mailbox interrupt
functions.
A given port’s interrupt is set (i.e., INT goes LOW)
whenever any other port on the device writes to the given
port’s address. For example, Port 1’s INT will go LOW if Port
2, Port 3, or Port 4 write to FFFFh (7FFFh for IDT70V5378).
The INT will go LOW in relation to the clock on the writing
port (see also the Mailbox Interrupt Timing waveform on
page 20). If a port writes to its own mailbox, no interrupt is
generated.
The mailbox location is a valid memory address:
the user can store an 18-bit data word at that location for
retrieval by the target port. In the event that two or more ports
attempt to set an interrupt to the same port at the same
time, the interrupt signal will go LOW, but the data actually
stored at that location will be indeterminate. The actual
interrupt is generated as a result of evaluating the state of
the address pins, the chip enables, and the R/W pin: if the
user wishes to set an interrupt to a specific port without
changing the data stored in that port’s mailbox, it is
possible to do so by disabling the byte enables during that
write cycle.
Once INT has gone LOW for a specific port, that
port can reset the INT by reading its assigned mailbox. In
the case of Port 1, it would clear its INT signal by reading
FFFFh (7FFFh for IDT70V5378). As stated previously, the
interrupt operation executes based on the state of the
address pins, the chip enables, and the R/W pin: it is
possible to clear the interrupt by asserting a read to the
appropriate location while keeping the output enable (OE) or
the byte enables deasserted, and so avoid having to drive
data on the I/O bus. The INT is reset, or goes HIGH again,
in relation to the reading port’s clock signal.
Master Reset
The IDT70V5388/78 is equipped with an asynchronous Master Reset input, which can be asserted independently of all clock inputs and will take effect per the Master
Reset timing waveform on page 18. The Master Reset sets
the internal value of all address counters to zero, and sets
the counter mask register on each port to all ones (i.e.,
completely unmasked). It also resets all mailbox interrupts
and counter interrupts to HIGH (i.e., non-asserted) and
sets all registered control signals to a deselected state. A
Master Reset operation must be performed after power-up,
in order to initialize the various registers on the device to a
known state. Master Reset will reset the device. For JTAG
and MBIST reset please refer to the JTAG Section on page
25.
—Mailbox Interrupt Flag Operations
Truth Table III—
Port 1(1,2)
Port 2(1,2)
Port 3(1,2)
Port 4(1,2)
R/W
CE
A15-A 0(4)
INT
R/W
CE
A15-A 0(4)
INT
R/W
CE
A15-A 0(4)
INT
R/W
CE
A15-A 0(4)
INT
X
X
X
L
L
L
FFFF
X
L
L
FFFF
X
L
L
FFFF
X
Set Port 1 INT Flag(3)
H
L
FFFF
H
X
X
X
X
X
X
X
X
X
X
X
X
Reset Port 1 INT Flag
L
L
FFFE
X
X
X
X
L
L
L
FFFE
X
L
L
FFFE
X
Set Port 2 INT Flag(3)
X
X
X
X
H
L
FFFE
H
X
X
X
X
X
X
X
X
Reset Port 2 INT Flag
L
L
FFFD
X
L
L
FFFD
X
X
X
X
L
L
L
FFFD
X
Set Port 3 INT Flag(3)
X
X
X
X
X
X
X
X
H
L
FFFD
H
X
X
X
X
Reset Port 3 INT Flag
L
L
FFFC
X
L
L
FFFC
X
L
L
FFFC
X
X
X
X
L
Set Port 4 INT Flag(3)
X
X
X
X
X
X
X
X
X
X
X
X
H
L
FFFC
H
Reset Port 4 INT Flag
Function
5649 tbl 14
NOTES:
1. The status of OE is a "Don't Care" for the interrupt logic circuitry. If it is desirable to reset the interrupt flag on a given port while keeping the I/O bus in a tri-state
condition, then this can be accomplished by setting OE = VIH while the read access is asserted to the appropriate address location.
2. The status of the LB and UB controls are "Don't Care" for the interrupt circuitry. If it is desirable to set the interrupt flag to a specific port without overwriting the
data value already stored at the mailbox location, then this can be accomplished by setting LB = UB = VIH during the write access for that specific mailbox.
Similarly, if it desirable to reset the interrupt flag on a given port while keeping the I/O bus in a tri-state condition, then this can be accomplished by setting LB
= UB = V IH while the read access is asserted to the appropriate address location.
3. The interrupt to a specific port can be set by any one of the other three ports. The appropriate control states for the other three ports are depicted above. In the
event that two or more ports attempt to set the same interrupt flag simultaneously via a valid data write, the data stored at the mailbox location will be
indeterminate.
4. A15 is a NC for IDT70V5378, therefore Mailbox Interrupt Addresses are 7FFF, 7FFE, 7FFD and 7FFC. Address comparison will be for A0 - A14 .
22
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Address Counter Control Operations
Each port on the IDT70V5388/78 is equipped with
an internal address counter, to ease the process of
bursting data into or out of the device. Truth Table II depicts
the specific operation of the counter functions, to include
the order of priority among the signals. All counter controls
are independent of chip enables. The device supports the
ability to load a new address value on each access, or to
load an address value on a given clock cycle via the CNTLD
control and then allow the counter to increase that value by
preset increments on each successive clock via the
CNTINC control (see also the Counter Mask Operations
section that follows). The counter can be suspended on
any clock cycle by disabling the CNTINC, and it can be
reset to zero on any clock cycle by asserting the CNTRST
control. CNTRST only affects the address value stored in the
counter: it has no effect on the counter mask register.
When the counter reaches the maximum value in
CNTRD
MKRD
the array (i.e., address FFFFh for IDT70V5388 and address
7FFFh for IDT70V5378) or it reaches the highest value
permitted by the Counter Mask Register, it then ‘wraps
around’ to the beginning of the array. When Address Min is
reached via counter increment (i.e., not as a result of an
external address load), then the CNTINT signal for that port
is driven low for one clock cycle, automatically resetting on
the next cycle.
When the CNTRD control is asserted, the
IDT70V5388/78 will output the current address stored in the
internal counter for that port as noted in the Load and Read
Address Counter timing waveform on page 19. The address
will be output on the address lines. During this output, the
data I/Os will be driven in accordance with the settings of
the chip enables, byte enables, and the output enable on
that port: the device does not automatically tri-state these
pins during the address readback operation.
Read Back
Register
Addr.
Read
Back
MKLD
Address
(I/O)
CNTLD
CNTINC
CNTRST
CLK
Mask
Register
Memory
Array
Counter/
Address
Register
,
5649 drw 22
Figure 4. Logic Block Diagram for Read Back Operations
23
6.42
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Counter-Mask Register
CNTINT
STEP 1
Load
Counter-Mask
Register = FF
H
0 0
0's
A15(2)A14
0 1 1 1 1 1 1 1 1
A8 A7 A6 A5 A4 A3 A2 A1 A0
Masked Address
STEP 2
Load
Address
Counter = FD
H
0 0
0's
A15(2) A14
STEP 3
Max
Address
Register
H
X X
Max + 1
Address
Register
L
X X
0 1 1 1 1 1 1 0 1
A8 A7 A6 A5 A4 A3 A2 A1 A0
X's
A15(2)A14
STEP 4
Counter Address
,
X 1 1 1 1 1 1 1 1
A8 A7 A6 A5 A4 A3 A2 A1 A0
X's
A15(2)A14
X 0 0 0 0 0 0 0 0
A8 A7 A6 A5 A4 A3 A2 A1 A0
Figure 5. Programmable Counter-Mask Register Operation (1)
5649 drw 23
NOTE:
1. The "X's" in this diagram represent the upper bits of the counter.
2. A15 is a NC for IDT70V5378.
The internal address counter on each port has an
associated Counter Mask Register that allows for configuration of the internal address counter on that port. Truth
Table III groups the operations of the address counter with
those of the counter mask register, to include Master Reset
and applicable readback operations.
Each bit in the mask register controls the corresponding bit in the internal address counter: writing a “1” to
a bit in the mask register allows that bit to increment in
response to CNTINC, while writing a “0” to a bit masks it (i.e.,
locks it at whatever value is loaded via CNTLD). The mask
register is extremely flexible: every bit can be controlled
independently of every other bit. The counter simply concatenates those bits that have not been masked, giving the
user great selectivity in determining which portions of the
memory array are available to a particular port for burst
operations.
Figure 5 illustrates the operation of the Counter
Mask Register in simply constraining a port to a selected
portion of the array, specifically addresses 0000h to 00FFh.
In step one, the mask register is loaded with 00FFh via MKLD
(see also the Load and Read Mask Register timing waveform on page 19). In step two, a starting address of 00FD is
asserted for the start point of a burst, and the CNTINC control
is enabled. Step three indicates the address counter
incrementing to 00FFh. In step four, the internal counter
determines that all address values greater than 00FFh have
been masked, and so it increments past this ‘max’ value to
0000h. As a result of reaching 0000h via the CNTINC
operation, the CNTINT output for this port is automatically
triggered – it will go low for one clock cycle and then reset.
The example depicted in Figure 5 is a very simple
one: it is also possible to mask non-contiguous bits, such
as loading 5555h in the mask register. As stated previously,
the address counter simply concatenates all bits that have
not been masked and continues to increment those bits in
accordance with the CNTINC control: in this fashion, if the
mask register is set at 5555h and a start address of 0007h
is asserted via CNTLD, the next value the counter will
increment to in response to the CNTINC control is 0012h,
then 0013h, then 0016h, etc.
Besides supporting precise control of which portions of the array are available to a particular port in burst
operations, the independent control on the mask register
bits also provides excellent flexibility in determining the
value by which the counter will increment. For example,
setting bit 0 of the mask register to “0” masks it from counter
operation, effectively configuring that port to count by
increments of two. This can be very useful in configuring two
ports to work in combination, effectively creating a single
36-bit port. Thus, Port 1 can be configured to count by two
starting on even addresses (the start point is asserted via
CNTLD), and Port 2 can be configured to count by two
starting on odd addresses (again via CNTLD). The two ports
together will operate on 36-bit data words, storing half of
each word in an even-numbered address, the other half in
an odd-numbered address. Setting bits 1 and 0 of the mask
register on a given port to “0” configures that port to count
24
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
in increments of four: masking bits 2, 1, and 0 configures
that port to count in increments of eight, and so on. The
ability to set the increments by which the counters will
advance gives the user the ability to interleave memory
operations among the ports, minimizing the concerns that
a given address might be written by more than one port at
any given point in time (an operation that would have
indeterminate results).
JTAG Support
The IDT70V5388/78 provides a serial boundary
scan test access port . The JTAG tables starting on page
29 provide the specific details for the JTAG implementation
on this device.
The IDT70V5388/78 executes a JTAG test logic
reset upon power-up. This power-up reset will initialize the
TAP controller and MBIST controller. In most power
environments no further action is required. However, if the
user has any concern about the system’s voltage states
during power-up, then the user can use the optional TRST
input as part of a board’s power on reset sequence. The
TRST pin also provides an alternate means of resetting the
JTAG test logic when required, and is available for use by
external JTAG controllers as an asynchronous reset signal.
If the user does not plan to rely on the optional TRST pin, but
wants to use JTAG functionality, the TRST pin should either
be tied HIGH (preferred implementation) or left floating.
If JTAG operations are not desired, the user has a
number of options for disabling the JTAG functions. One
would be to simply tie TCK LOW, leaving all other JTAG pins
floating (alternatively, TDI and TMS could be tied HIGH).
Since the device executes a JTAG reset upon power-up:
with TCK tied LOW, no further clocking of the TAP will occur
and no JTAG operations will take place. Alternatively, the
user can opt to tie TRST LOW (either in lieu of or in addition
to tying TCK LOW) and the TAP will be locked in a reset
condition, blocking all JTAG operations.
Memory Built-In-Test Operations
Go-NoGo Testing
The IDT70V5388/78 is equipped with a self-test
function that can be run by the user as the result of a single
instruction, implemented via the JTAG TAP interface. If
multiple FourPort devices are used on the same board, all
can execute MBIST simultaneously, facilitating board
checkout.
The MBIST function executes a Go-NoGo test
within the device, which then captures pass-fail information
and failure count in a special register called the MBIST
Result Register (MRR). Upon completion of the test, the
MRR can be scanned out via the JTAG interface, using the
internal scan operation. Bit zero of the MRR (MRR[0]) is a
don't care. Bit one of the MRR (MRR[1])indicates the pass/
fail status: a "0" indicates some sort of failure was noted,
25
6.42
while a "1" indicates that the memory array passed. The rest
of the MRR contains the total number of failed read cycles
in the entire MBIST sequence.
The IDT70V5388/78 MBIST function has been
supplemented with the ability for the user to force a failure
report from the device. This allows the user the flexibility of
validating the MBIST function itself, by verifying that the
device is able to report faults as well as passing results. The
two modes of operation, normal MBIST testing and forced
error reporting, are controlled via the JTAG TAP interface
using the instruction PROGRAM_MBIST_MODE_SELECT.
For further detail, please refer to the System Interface
Parameters table on page 28.
The MBIST function executes once the RUNBIST
instruction is input via the JTAG interface. The entire MBIST
test will be performed with a deterministic number of TCK
cycles depending on the TCK and CLKMBIST frequency.
This can be calculated by using the following formula:
tCYC =
tCYC[CLKMBIST]
tCYC[TCK]
x m + SPC, where:
tCYC is the total number of TCK cycles required to run
MBIST.
SPC is the synchronization padding cycles (typically 4-6
cycles, to accommodate state machine overhead, turnaround cycles, etc.)
m is a constant that represents the number of read and write
operations required to run the internal MBIST algorithms
(14,811,136) for both IDT70V5388 and IDT70V5378.
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
JTAG/BIST TAP Controller Block Diagram
0
Bypass Register (BYR)
1
0
MBIST Mode Select Register (MSR)
3 2
1 0
Instruction Register (IR)
25 24
TDI
1 X
MBIST Result Register (MRR)
31 30 29
0
Identification Register (IDR)
391
Selection
Circuitry
TDO
(MUX)
0
Boundary Scan Register (BSR)
CLKMBIST
MBIST
CONTROLLER
TAP
CONTROLLER
TCK
TMS
TRST
MEMORY
CELL
5649 drw 25
26
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
JTAG Timing Specifications
tTCYC
tTL
tTH
TCK
Device Inputs(1)/
TDI/TMS
tJS
Device Outputs(2)/
TDO
tJDC
tJH
tJRSR
tJCD
TRST
5649 drw 26
tJRST
NOTES:
1. Device inputs = All device inputs except TDI, TMS, and TRST.
2. Device outputs = All device outputs except TDO.
3. To reset the test (JTAG) port without resetting the device, TMS must be held LOW for 5 cycles, or TRST must be held LOW for one cycle.
27
6.42
,
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Identification Register Definitions
Instruction Field
Value
Revision Number (31:28)
IDT Device ID (27:12)
Description
0x0
Reserved for version number
(1)
Defines IDT part number
0x31D
IDT JEDEC ID (11:1)
0x33
ID Register Indicator Bit (Bit 0)
Allows unique identification of device vendor as IDT
1
Indicates the presence of an ID register
5649 tbl 15
NOTE:
1. Device ID for IDT70V5378 is 0x31E.
Scan Register Sizes
Register Name
Bit Size
Instruction (IR)
4
MBIST Mode Select Register (MSR)
2
Bypass (BYR)
1
Identification (IDR)
Boundary Scan (BSR)
MBIST Result (MRR)
32
392 Note (3)
26
System Interface Parameters
Instruction
EXTEST
5649 tbl 16
Code
Description
Forces contents of the boundary scan cells onto the device outputs(1).
Places the boundary scan register (BSR) between TDI and TDO.
0000
BYPASS
1111
Places the b ypass register (BYR) between TDI and TDO.
IDCODE
0111
Loads the ID register (IDR) with the vendor ID code and places the
register between TDI and TDO.
0110
Places the bypass register (BYR) b etween TDI and TDO. Forces all
device output drivers to a High-Z state.
0001
Places the boundary scan register (BSR) between TDI and TDO.
SAMPLE allows data from device inputs(2) to be captured in the
boundary scan cells and shifted serially through TDO. PRELOAD allows
data to be input serially into the boundary scan cells via the TDI.
HIGHZ
SAMPLE/PRELOAD
1010
Places the MBIST Mode Register between TDI and TDO. A value of '00'
written into this register will allow MBIST to run in standard memory test
mode, outputting valid results as appropriate via the MBIST Result
Register. A value of '11' written into the MBIST Mode Register will force
the MBIST Result Register (MRR) to report a result of 'FAIL'., with 8E0000
failed read cycles noted (i.e., the MRR content = (8E0000h, 0, x). The
value of the MBIST Mode Register is no t guaranteed at power-up and is
not affected b y Master reset and JTAG reset.
RUNBIST
1000
Invokes MBIST. Internally updates MBIST result register with Go-NoGo
information and number of issues. PROGRAM_MBIST_MODE_REGISTER
must be run prior to executing RUNBIST in order to ensure valid results.
There is no need to repeat this instructio n unless the mode of operation
is changed: the MMR will re tain its programmed value until overwritten or
the device is powered down.
INT_SCAN
0100
Scans out partial information. Places MBIST result register (MRR)
between TDI & TDO.
CLAMP
0101
Uses BYR. Forces contents of the boundary scan cells onto the device
outputs. Places the Bypass reg ister (BYR) between TDI & TDO.
0010, 0011
Several combinations are reserved. Do not use codes other than those
identified above.
MBIST_MODE_SELECT
RESERVED
PRIVATE
1001, 1011, 1100, 1101, 1110
Several combinations arePRIVATE (for IDT internal use). Do not use
codes other than those identified above.
NOTES:
1. Device outputs = All device outputs except TDO.
2. Device inputs = All device inputs except TDI, TMS, and TRST.
3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local
IDT sales representative.
28
5649 tbl 17
IDT70V5388/78
3.3V 64/32K x 18 Synchronous FourPort™ Static RAM
Industrial and Commercial Temperature Ranges
Ordering Information
IDT XXXXX
Device
Type
A
999
A
A
Power
Speed
Package
Process/
Temperature
Range
Blank
I
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
BG
BC
272-ball BGA (BG272-1)
256-ball BGA (BG256-1)
200
166
133
100
Commercial Only
Commercial & Industrial
Commercial & Industrial
Commercial & Industrial
S
Speed in MHZ
Standard Power
70V5388 1152K (64K x 18) 3.3V FourPort™ RAM
70V5378 576K (32K x 18) 3.3V FourPort™ RAM
5649 drw 27
Datasheet Document History
08/20/02:
09/25/02:
08/20/03:
Initial Public Datasheet
Added 0.5M Density to Datasheet
Page 10 Changed power numbers in DC Electrical Characteristics table
Removed Preliminary status
CORPORATE HEADQUARTERS
2975 Stender Way
Santa Clara, CA 95054
for SALES:
800-345-7015 or 408-727-6116
fax: 408-492-8674
www.idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
29
6.42
for Tech Support:
831-754-4613
[email protected]
Similar pages