IDT IDT72605L50J Cmos syncbififoo 256 x 18 x 2 and 512 x 18 x 2 Datasheet

CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
IDT72605
IDT72615
Integrated Device Technology, Inc.
FEATURES:
DESCRIPTION:
• Two independent FIFO memories for fully bidirectional
data transfers
• 256 x 18 x 2 organization (IDT 72605)
• 512 x 18 x 2 organization (IDT 72615)
• Synchronous interface for fast (20ns) read and write
cycle times
• Each data port has an independent clock and read/write
control
• Output enable is provided on each port as a three-state
control of the data bus
• Built-in bypass path for direct data transfer between two
ports
• Two fixed flags, Empty and Full, for both the A-to-B and
the B-to-A FIFO
• Programmable flag offset can be set to any depth in the
FIFO
• The synchronous BiFIFO is packaged in a 64-pin TQFP
(Thin Quad Flatpack), 68-pin PGA and 68-pin PLCC
• Industrial temperature range (-40oC to +85oC) is available, tested to military electrical specifications
The IDT72605 and IDT72615 are very high-speed, lowpower bidirectional First-In, First-Out (FIFO) memories, with
synchronous interface for fast read and write cycle times. The
SyncBiFIFO is a data buffer that can store or retrieve
information from two sources simultaneously. Two Dual-Port
FIFO memory arrays are contained in the SyncBiFIFO; one
data buffer for each direction.
The SyncBiFIFO has registers on all inputs and outputs.
Data is only transferred into the I/O registers on clock edges,
hence the interfaces are synchronous. Each Port has its own
independent clock. Data transfers to the I/O registers are
gated by the enable signals. The transfer direction for each
port is controlled independently by a read/write signal. Individual output enable signals control whether the SyncBiFIFO is
driving the data lines of a port or whether those data lines are
in a high-impedance state.
Bypass control allows data to be directly transferred from
input to output register in either direction.
The SyncBiFIFO has eight flags. The flag pins are full,
empty, almost-full, and almost-empty for both FIFO memories. The offset depths of the almost-full and almost-empty
flags can be programmed to any location.
The SyncBiFIFO is fabricated using IDT’s high-speed,
submicron CMOS technology.
FUNCTIONAL BLOCK DIAGRAM
DA0-DA17
ENA
R/ WA
OEA
HIGH
Z
CONTROL
INPUT REGISTER
CLKA
CSA
A2
A1
A0
EFAB
PAEAB
PAFAB
FFAB
OUTPUT REGISTER
µP
INTERFACE
MUX
MEMORY
ARRAY
512 x 18
256 x 18
FLAG
LOGIC
MEMORY
ARRAY
512 x 18
256 x 18
OEB
R/ WB
ENB
RS
FLAG
LOGIC
EFBA
PAEBA
PAFBA
FFBA
POWER
SUPPLY
MUX
OUTPUT REGISTER
CLKB
RESET
LOGIC
3
7
VCC
GND
INPUT REGISTER
HIGH
Z
CONTROL
BYPB
DB0-DB17
2704 drw 01
SyncBiFIFO is a trademark and the IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL TEMPERATURE RANGES
1996 Integrated Device Technology, Inc.
DECEMBER 1996
For latest information contact IDT's web site at www.idt.com or fax-on-demand at 408-492-8391.
5.18
DSC-2704/5
1
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
PIN CONFIGURATIONS
11
DB3
DB4
DB5
DB7
GND
DB6
DB8
10
DB1
DB2
09
RS
DB0
DB9
VCC
DB11 DB13 GND
GND DB10
DB12 DB14 DB15
DB16
OEA
DB17
08 R/WB CLKB
07
OEB ENB
06 GND
05
PAEAB PAFAB
EFAB FFAB
G68-1
BYPB
PAEBA PAFBA
A2
VCC
A0
A1
Pin 1 Designator
04
EFBA FFBA
ENA CSA
03
DA1
DA0
CLKA R/WA
02
DA2
DA3
GND
DA6
DA8
GND DA10
DA12 DA14 DA16
DA4
DA5
DA7
DA9
VCC
DA11
DA13 GND DA15
B
C
D
E
F
G
01
A
H
J
L
2704 drw 02
DA15
GND
DA14
DA13
DA12
DA11
DA10
VCC
GND
DA9
DA8
DA7
DA6
DA5
GND
DA4
DA3
PGA
Top View
K
DA17
9 8 7 6 5 4 3 2
68 67 66 65 64 63 62 61
1
10
60
11
59
12
58
57
13
56
14
55
15
54
16
53
17
J68-1
52
18
51
19
50
20
49
21
48
22
47
23
46
24
45
25
44
26
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
DB15
GND
DB14
DB13
DB12
DB11
DB10
VCC
GND
DB9
DB8
DB7
DB6
DB5
GND
DB4
DB3
DA16
DA17
CLK A
R/W A
EN A
CS A
A0
A1
A2
VCC
EFAB
FFAB
PAE AB
PAFAB
OE A
D B17
D B16
DA2
DA1
DA0
EFBA
FF BA
PAEBA
PAF BA
GND
BYPB
OEB
ENB
R/WB
CLKB
RS
DB0
DB1
DB2
2704 drw 03
PLCC
Top View
5.18
2
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
DB2
DB1
DB0
RS
CLKB
BYBB
OEB
ENB
R/WB
GND
EFBA
FFBA
PAEBA
PAFBA
DA0
DA1
PIN CONFIGURATIONS
PIN 1
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
DA2
1
48
DB3
DA3
2
47
DB4
DA4
3
46
GND
DA5
4
45
DB5
DA6
5
44
DB6
DA7
6
43
DB7
DA8
7
42
DB8
DA9
8
41
DB9
GND
9
40
DB10
VCC
10
39
DB11
DA10
11
38
DB12
DA11
12
37
DB13
DA12
13
36
DB14
DA13
14
35
GND
DA14
15
34
DB15
DA15
16
33
DB16
PN64-1
DB17
EFAB
FFAB
PAEAB
PAFAB
OEA
VCC
A2
A1
A0
ENA
CSA
R/W A
CLKA
DA17
DA16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
2704 drw 04
TQFP
Top View
5.18
3
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
PIN DESCRIPTION
Symbol
DA0-DA17
CSA
R/WA
Name
Data A
I/O
I/O
Chip Select A
I
Read/Write A
I
CLKA
Clock A
I
ENA
Enable A
I
OEA
Output Enable A
I
A0, A1, A2 Addresses
I
DB0-DB17
Data B
R/WB
Read/Write B
I
CLKB
Clock B
I
ENB
Enable B
I
OEB
Output Enable B
I
EFAB
A→B Empty Flag
O
A→B
Programmable
Almost-Empty Flag
O
A→B
Programmable
Almost-Full Flag
O
FFAB
A→B Full Flag
O
EFBA
B→A Empty Flag
O
B→A
Programmable
Almost-Empty Flag
O
B→A
Programmable
Almost-Full Flag
O
PAEAB
PAFAB
PAEBA
PAFBA
I/O
Description
Data inputs & outputs for the 18-bit Port A bus.
Port A is accessed when CSA is LOW. Port A is inactive if CSA is HIGH.
This pin controls the read or write direction of Port A. If R/WA is LOW, Data A input data is
written into Port A. If R/WA is HIGH, Data A output data is read from Port A. In bypass mode,
when R/WA is LOW, message is written into A→B output register. If R/WA is HIGH, message
is read from B→A output register.
CLKA is typically a free running clock. Data is read or written into Port A on the rising edge of
CLKA.
When ENA is LOW, data can be read or written to Port A. When ENA is HIGH, no data
transfers occur.
When R/WA is HIGH , Port A is an output bus and OEA controls the high-impedance state of
DA0-DA17. If OEA is HIGH, Port A is in a high-impedance state. If OEA is LOW while CSA is
LOW and R/WA is HIGH, Port A is in an active (low-impedance) state.
When CSA is asserted, A0, A1, A2 and R/WA are used to select one of six internal resources.
Data inputs & outputs for the 18-bit Port B bus.
This pin controls the read or write direction of Port B. If R/WB is LOW, Data B input data is
written into Port B. If R/WB is HIGH, Data B output data is read from Port B. In bypass mode,
when R/WB is LOW, message is written into B→A output register. If R/WB is HIGH, message
is read from A→B output register.
Clock B is typically a free running clock. Data is read or written into Port B on the rising edge
of CLKB.
When ENB is LOW, data can be read or written to Port B. When ENB is HIGH, no data
transfers occur.
When R/WB is HIGH , Port B is an output bus and OEB controls the high-impedance state of
DB0-DB17. If OEB is HIGH, Port B is in a high-impedance state. If OEB is LOW while R/WB
is HIGH, Port B is in an active (low-impedance) state.
When EFAB is LOW, the A→B FIFO is empty and further data reads from Port B are inhibited.
When EFAB is HIGH, the FIFO is not empty. EFAB is synchronized to CLKB. In the bypass
mode, EFAB HIGH indicates that data DA0-DA17 is available for passing through. After the
data DB0-DB17 has been read, EFAB goes LOW.
When PAEAB is LOW, the A→B FIFO is almost empty. An almost empty FIFO contains less
than or equal to the offset programmed into PAEAB Register. When PAEAB is HIGH, the
A→B FIFO contains more than offset in PAEAB Register. The default offset value for PAEAB
Register is 8. PAEAB is synchronized to CLKB.
When PAFAB is LOW, the A→B FIFO is almost full. An almost full FIFO contains greater than
the FIFO depth minus the offset programmed into PAFAB Register. When PAFAB is HIGH,
the A→B FIFO contains less than or equal to the depth minus the offset in PAFAB Register.
The default offset value for PAFAB Register is 8. PAFAB is synchronized to CLKA.
When FFAB is LOW, the A→B FIFO is full and further data writes into Port A are inhibited.
When FFAB is HIGH, the FIFO is not full. FFAB is synchronized to CLKA. In bypass mode,
FFAB tells Port A that a message is waiting in Port B’s output register. If FFAB is LOW, a
bypass message is in the register. If FFAB is HIGH, Port B has read the message and another
message can be written into Port A.
When EFBA is LOW, the B→A FIFO is empty and further data reads from Port A are inhibited.
When EFBA is HIGH, the FIFO is not empty. EFBA is synchronized to CLKA. In the bypass
mode, EFBA HIGH indicates that data DB0-DB17 is available for passing through. After the
data DA0-DA17 has been read, EFBA goes LOW on the following cycle.
When PAEBA is LOW, the B→A FIFO is almost empty. An almost empty FIFO contains less
than or equal to the offset programmed into PAEBA Register. When PAEBA is HIGH, the
B→A FIFO contains more than offset in PAEBA Register. The default offset value for PAEBA
Register is 8. PAEBA is synchronized to CLKA.
When PAFBA is LOW, the B→A FIFO is almost full. An almost full FIFO contains greater than
the FIFO depth minus the offset programmed into PAFBA Register. When PAFBA is HIGH,
the B→A FIFO contains less than or equal to the depth minus the offset in PAFBA Register.
The default offset value for PAFBA Register is 8. PAFBA is synchronized to CLKB.
2704 tbl 01
5.18
4
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
PIN DESCRIPTION (Continued)
Symbol
FFBA
Name
I/O
Description
When FFBA is LOW, the B→A FIFO is full and further data writes into Port B are inhibited.
When FFBA is HIGH, the FIFO is not full. FFBA is synchronized to CLKB. In bypass mode,
FFBA tells Port B that a message is waiting in Port A’s output register. If FFBA is LOW, a
bypass message is in the register. If FFBA is HIGH, Port A has read the message and another
message can be written into Port B.
B→A Full Flag
O
Port B Bypass
Flag
O
RS
This flag informs Port B that the Synchronous BiFIFO is in bypass mode. When BYPB is
LOW, Port A has placed the FIFO into bypass mode. If BYPB is HIGH, the Synchronous
BiFIFO passes data into memory. BYPB is synchronized to CLKB.
Reset
I
A LOW on this pin will perform a reset of all Synchronous BiFIFO functions.
VCC
Power
There are three +5V power pins for the PLCC and PGA packages and two for the TQFP.
GND
Ground
There are seven ground pins for the PLCC and PGA packages and four for the TQFP.
BYPB
2704 tbl 02
RECOMMENDED DC
OPERATING CONDITIONS
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Rating
Com’l.
Mil.
Unit
VTERM
Terminal Voltage
with Respect
to Ground
–0.5 to +7.0
–0.5 to +7.0
V
TA
Operating
Temperature
0 to +70
–55 to +125
Symbol
°C
TBIAS
Temperature
Under Bias
–55 to +125
–65 to +135
°C
TSTG
Storage
Temperature
–55 to +125
–65 to +150
°C
IOUT
DC Output Current
50
50
mA
Parameter
Min. Typ. Max. Unit
VCC
Supply Voltage
4.5
5.0
5.5
V
GND
Supply Voltage
0
0
0
V
VIH
Input High Voltage
2.0
—
—
V
VIL(1)
Input Low Voltage
—
—
0.8
NOTE:
1. 1.5V undershoots are allowed for 10ns once per cycle.
V
2704 tbl 04
CAPACITANCE (TA = +25°C, F = 1.0MHz)
NOTE:
2704 tbl 03
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
Symbol
Parameter
CIN(2)
Input Capacitance
VIN = 0V
Conditions
10
COUT(1,2)
Output Capacitance
VOUT = 0V
10
NOTES:
1. With output deselected.
2. Characterized values, not currently tested.
Max. Unit
pF
pF
2704 tbl 05
DC ELECTRICAL CHARACTERISTICS
(Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C)
Symbol
IIL(1)
IOL(2)
VOH
VOL
ICC(3)
Parameter
Input Leakage Current (Any Input)
Output Leakage Current
Output Logic "1" Voltage IOUT = –2mA
Output Logic "0" Voltage IOUT = 8mA
Average VCC Power Supply Current
Min.
–1
–10
2.4
—
—
NOTES:
1. Measurements with 0.4V ≤ VIN ≤ VCC.
2. OEA, OEB ≥ VIH; 0.4 ≤ VOUT ≤ VCC.
3. Tested with outputs open. Testing frequency f=20MHz
IDT72615L
IDT72605L
Commercial
tCLK = 20, 25, 35, 50ns
Typ.
—
—
—
—
—
Max.
Unit
1
10
—
0.4
230
µA
µA
V
V
mA
2704 tbl 06
5.18
5
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
+5V
AC TEST CONDITIONS
In Pulse Levels
GND to 3.0V
Input Rise/Fall Times
3ns
Input Timing Reference Levels
1.5V
Output Reference Levels
1.5V
Output Load
1.1KΩ
D.U.T.
See Figure 2
680Ω
2704 tbl 07
30pF*
2704 drw 05
or equivalent circuit
Figure 2. Output Load
* Includes jig and scope capacitances.
AC ELECTRICAL CHARACTERISTICS
(Commercial: VCC = 5V±10%, TA = 0°C to +70°C)
Symbol
fCLK
Parameter
Clock frequency
72615L20
72605L20
Min.
Max.
—
50
Commercial
72615L25
72615L35
72615L50
72605L25
72605L35
72605L50
Min. Max. Min. Max. Min.
Max. Unit
—
40
—
28
—
20 MHz
Timing Figures
—
tCLK
Clock cycle time
20
—
25
—
35
—
50
—
ns
4,5,6,7
tCLKH
Clock HIGH time
8
—
10
—
14
—
20
—
ns
4,5,6,7,12,13,14,15
tCLKL
Clock LOW time
8
—
10
—
14
—
20
—
ns
4,5,6,7,12,13,14,15
tRS
Reset pulse width
20
—
25
—
35
—
50
—
ns
3
tRSS
Reset set-up time
12
—
15
—
21
—
30
—
ns
3
tRSR
Reset recovery time
12
—
15
—
21
—
30
—
ns
3
tRSF
Reset to flags in intial state
—
27
—
28
—
35
—
50
ns
3
tA
Data access time
3
10
3
15
3
21
3
25
ns
5,7,8,9,10,11
tCS
Control signal set-up time(1)
6
—
6
—
8
—
10
—
ns
4,5,6,7,8,9,10,11,
12, 13,14,15
tCH
Control signal hold time(1)
1
—
1
—
1
—
1
—
ns
4,5,6,7,10,11,12,
13, 14,15
tDS
Data set-up time
6
—
6
—
8
—
10
—
ns
4,6,8,9,10,11
tDH
Data hold time
1
—
1
—
1
—
1
—
ns
4,6
tOE
Output Enable LOW to
output data valid(2)
3
10
3
13
3
20
3
28
ns
5,7,8,9,10,11
tOLZ
Output Enable LOW to data
bus at Low-Z(2)
0
—
0
—
0
—
0
—
ns
5,7,8,9,10,11
tOHZ
Output Enable HIGH to data
bus at High-Z(2)
3
10
3
13
3
20
3
28
ns
5,7,10,11
tFF
Clock to Full Flag time
—
10
—
15
—
21
—
30
ns
4,6,10,11
tEF
Clock to Empty Flag time
—
10
—
15
—
21
—
30
ns
5,7,8,9,10,11
tPAE
Clock to Programmable
Almost Empty Flag time
—
12
—
15
—
21
—
30
ns
12,14
tPAF
Clock to Programmable
Almost Full Flag time
—
12
—
15
—
21
—
30
ns
13,15
tSKEW1
Skew between CLKA & CLKB
for Empty/Full Flags(2)
10
—
12
—
17
—
20
—
ns
4,5,6,7,8,9,10,11
tSKEW2
Skew between CLKA & CLKB
for Programmable Flags(2)
17
—
19
—
25
—
34
—
ns
4, 7,12,13,14,15
NOTES:
1. Control signals refer to CSA, R/WA, ENA, A2, A1, A0, R/WB, ENB.
2. Minimum values are guaranteed by design.
2704 tbl 08
5.18
6
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
FUNCTIONAL DESCRIPTION
RESET
IDTs SyncBiFIFO is versatile for both multiprocessor and
peripheral applications. Data can be stored or retrieved from
two sources simultaneously.
The SyncBiFIFO has registers on all inputs and outputs.
Data is only transferred into the I/O registers on clock edges,
hence the interfaces are synchronous. Two Dual-Port FIFO
memory arrays are contained in the SyncBiFIFO; one data
buffer for each direction. Each port has its own independent
clock. Data transfers to the I/O registers are gated by the
enable signals. The transfer direction for each port is controlled independently by a read/write signal. Individual output
enable signals control whether the SyncBiFIFO is driving the
data lines of a port or whether those data lines are in a highimpedance state. The processor connected to Port A of the
BiFIFO can send or receive messages directly to the Port B
device using the 18-bit bypass path.
The SyncBiFIFO can be used in multiples of 18-bits. In a 36to 36-bit configuration, two SyncBiFIFOs operate in parallel.
Both devices are programmed simultaneously, 18 data bits to
each device. This configuration can be extended to wider bus
widths (54- to 54-bits, 72- to 72-bits, etc.) by adding more
SyncBiFIFOs to the configuration. Figure 1 shows multiple
SyncBiFIFOs configured for multiprocessor communication.
The microprocessor or microcontroller connected to Port A
controls all operations of the SyncBiFIFO. Thus, all Port A
interface pins are inputs driven by the controlling processor.
Port B interfaces with a second processor. The Port B control
pins are inputs driven by the second processor.
Reset is accomplished whenever the Reset (RS) input is
taken to a LOW state with CSA, ENA and ENB HIGH. During
reset, both internal read and write pointers are set to the first
location. A reset is required after power up before a write
operation can take place. The A→B and B→A FIFO Empty
Flags (EFAB, EFBA) and Programmable Almost Empty Flags
(PAEAB, PAEBA) will be set to LOW after tRSF. The A→B and
B→A FIFO Full Flags (FFAB, FFBA) and Programmable Almost
Full Flags (PAFAB, PAFBA) will be set to HIGH after tRSF. After
the reset, the offsets of the Almost-Empty Flags and AlmostFull Flags for the A→B and B→A FIFO offset default to 8.
PORT A INTERFACE
The SyncBiFIFO is straightforward to use in micro-processor-based systems because each port has a standard
microprocessor control set. Port A interfaces with microprocessor through the three address pins (A2-A0) and a Chip Select
CSA pins. When CSA is asserted, A2,A1,A0 and R/WA are used
to select one of six internal resources (Table 1).
With A2=0 and A1=0, A0 determines whether data can be
read out of output register or be written into the FIFO (A0=0),
or the data can pass through the FIFO through the bypass
path (A0=1).
With A2=1, four programmable flags (two A→B FIFO programmable flags and two B→A FIFO programmable flags)
can be selected: the A→B FIFO Almost-Empty Flag Offset
(A1=0, A0=0), A→B FIFO Almost-Full Flag Offset (A1=0, A0=1),
B→A FIFO Almost-Empty Flag Offset (A1=1, A0=0), B→A FIFO
Almost-Full Flag Offset (A1=1, A0=1).
Port A is disabled when CSA is deasserted and data A is in
high-impedance state.
IDT
SYNCBIFIFO
DATA A
DATA B
CLK A
CLK B
CONTROL A CONTROL B
CLK
CLK
MICROPROCESSOR
A
MICROPROCESSOR
B
DATA
ADDR, I/0
RAM A
CONTROL
LOGIC
DATA
IDT
SYNCBIFIFO
CONTROL
LOGIC
DATA A
DATA B
CLK A
CLK B
CONTROL A CONTROL B
RAM B
SYSTEM
CLOCK B
SYSTEM
CLOCK A
ADDR, I/0
2704 drw 06
NOTES:
1. Upper SyncBiFIFO only is used in 18- to 18-bit configuration.
2. Control A Consists of R/WA, ENA, OEA, CSA, A2, A1, A0. Control B consists of R/WB, ENB, OEB.
Figure 1. 36- to 36-bit Processor Interface Configuration.
5.18
7
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
CSA
R/WA
ENA
OEA
Data A
I/O
0
0
0
0
I
Data A is written on CLKA ≠. This write cycle immediately following
low-impedance cycle is prohibited. Note that even though OEA = 0, a
LOW logic level on R/WA, once qualified by a rising edge on CLKA, will
put Data A into a high-impedance state.
0
0
0
1
I
Data A is written on CLKA ≠
0
0
1
X
I
Data A is ignored
0
1
0
0
O
Data is read(1) from RAM array to output register on CLKA ≠,
Data A is low-impedance
0
1
0
1
O
Data is read(1) from RAM array to output register on CLKA ≠,
Data A is high-impedance
0
1
1
0
O
Output register does not change(2), Data A is low-impedance
0
1
1
1
O
Output register does not change(2), Data A is high-impedance
1
0
X
X
I
Data A is ignored(3)
1
1
X
X
O
Data A is high-impedance(3)
Port A Operation
2704 tbl 09
NOTES:
1. When A2A1A0 = 000, the next B→A FIFO value is read out of the output register and the read pointer advances. If A2A1A0 = 001, the bypass path is
selected and bypass data from the Port B input register is read from the Port A output register. If A2A1A00 = 1XX, a flag offset register is selected
and its offset is read out through Port A output register.
2. Regardless of the condition of A2A1A0, the data in the Port A output register does not change and the B→A read pointer does not advance.
3. If CSA# is HIGH, then BYPB is HIGH. No bypass occur under this condition.
Table 1. Port A Operation Control Signals
BYPASS PATH
The bypass paths provide direct communication between
Port A and Port B. There are two full 18-bit bypass paths, one
in each direction. During a bypass operation, data is passed
directly between the input and output registers, and the FIFO
memory is undisturbed.
Port A initiates and terminates all bypass operations. The
bypass flag, BYPB, is asserted to inform Port B that a bypass
operation is beginning. The bypass flag state is controlled by
the Port A controls, although the BYPB signal is synchronized
to CLKB. So, BYPB is asserted on the next rising edge of CLKB
when A2A1A0=001and CSA is LOW. When Port A returns to
normal FIFO mode (A2A1A0=000 or CSA is HIGH), BYPB is
deasserted on the next CLKB rising edge.
Once the SyncBiFIFO is in bypass mode, all data transfers
are controlled by the standard Port A (R/WA, CLKA, ENA, OEA)
and Port B (R/WB, CLKB, ENB, OEB) interface pins. Each
bypass path can be considered as a one word deep FIFO.
Data is held in each input register until it is read. Since the
controls of each port operate independently, Port A can be
reading bypass data at the same time Port B is reading bypass
data.
When R/WA and ENA is LOW, data on pins DA0-DA17 is
written into Port A input register. Following the rising edge of
CLKA for this write, the A→B Full Flag (FFAB) goes LOW.
Subsequent writes into Port A are blocked by internal logic
until FFAB goes HIGH again. On the next CLKB rising edge,
the A→B Empty Flag (EFAB) goes HIGH indicating to Port B
that data is available. Once R/WB is HIGH and ENB is LOW,
data is read into the Port B output register. OEB still controls
whether Port B is in a high-impedance state. When OEB is LOW,
the output register data appears at DB0-DB17. EFAB goes LOW
following the CLKB rising edge for this read. FFAB goes HIGH
on the next CLKA rising edge, letting Port A know that another
word can be written through the bypass path.
Bypass data transfers from Port B to Port A work in a similar
manner with EFBA and FFBA indicating the Port A output
register state.
When the Port A address changes from bypass mode
(A2A1A0=001) to FIFO mode (A2A1A0=000) on the rising edge
of CLKA, the data held in the Port B output register may be
overwritten. Unless Port A monitors the BYPB pin and waits
for Port B to clock out the last bypass word, data from the A→B
FIFO will overwrite data in the Port B output register. BYPB will
go HIGH on the rising edge of CLKB signifying that Port B has
finished its last bypass operation. Port B must read any
bypass data in the output register on this last CLKB clock or it
is lost and the SyncBiFIFO returns to FIFO operations. It is
especially important to monitor BYPB when CLKB is much
slower than CLKA to avoid this condition. BYPB will also go
HIGH after CSA is brought HIGH; in this manner the Port B
bypass data may also be lost.
Since the Port A processor controls CSA and the bypass
mode, this scenario can be handled for B→A bypass data. The
Port A processor must be set up to read the last bypass word
before leaving bypass mode.
5.18
8
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
CSA
0
0
0
A2
0
0
1
A1
0
0
0
A0
0
1
0
0
1
0
1
0
1
1
0
0
1
1
1
1
X
X
X
COMMERCIAL TEMPERATURE RANGE
PROGRAMMABLE FLAGS
Read
Write
B→A FIFO A→B FIFO
18-bit Bypass Path
A→B FIFO Almost-Empty
Flag Offset
A→B FIFO Almost-Full
Flag Offset
B→A FIFO Almost-Empty
Flag Offset
B→A FIFO Almost-Full
Flag Offset
Port A Disabled
2704 tbl 10
Table 2. Accessing Port A Resources Using CSA, A2, A1, and A0.
PORT A CONTROL SIGNALS
The Port A control signals pins dictate the various operations shown in Table 2. Port A is accessed when CSA is LOW,
and is inactive if CSA is HIGH. R/WA and ENA lines determine
when Data A can be written or read. If R/WA and ENA are LOW,
data is written into input register on the LOW-to-HIGH transition
of CLKA. If R/WA is HIGH and OEA is LOW, data comes out
of bus and is read from output register into three-state buffer.
Refer to pin descriptions for more information.
The IDT SyncBiFIFO has eight flags: four flags for A→B FIFO
(EFAB, PAEAB, PAFAB, FFAB), and four flags for B→A FIFO
(EFBA, PAEBA, PAFBA, FFBA). The Empty and Full flags are
fixed, while the Almost Empty and Almost Full offsets can be
set to any depth through the Flag Offset Registers (see Table
3). The flags are asserted at the depths shown in the Flag
Truth Table (Table 4). After reset, the programmable flag
offsets are set to 8. This means the Almost Empty flags are
asserted at Empty +8 words deep, and the Almost Full flags
are asserted at Full -8 words deep.
The PAEAB is synchronized to CLKB, while PAEAB is synchronized to CLKA; and PAEBA is synchronized to CLKA, while
PAEBA is synchronized to CLKB. If the minimum time (tSKEW2)
between a rising CLKB and a rising CLKA is met, the flag will
change state on the current clock; otherwise, the flag may not
change state until the next clock rising edge. For the specific
flag timings, refer to Figures 12-15.
PORT B CONTROL SIGNALS
The Port B control signal pins dictate the various operations
shown in Table 5. Port B is independent of CSA. R/WB and
ENB lines determine when Data can be written or read in Port
B. If R/WB and ENB are LOW, data is written into input register,
and on LOW-to-HIGH transition of CLKB data is written into
PAEAB
17
X
16
X
15
X
14
X
13
X
12
X
11
X
10
X
9
X
8
7
6
5
4
3
2
1
A→B FIFO Almost-Empty Flag Offset
0
Register
PAFAB
17
X
16
X
15
X
14
X
13
X
12
X
11
X
10
X
9
X
8
7
6
5
4
3
2
1
A→B FIFO Almost-Full Flag Offset
0
Register
PAEBA
17
X
16
X
15
X
14
X
13
X
12
X
11
X
10
X
9
X
8
7
6
5
4
3
2
1
B→A FIFO Almost-Empty Flag Offset
0
Register
16
X
15
X
14
X
13
X
12
X
11
X
10
X
9
X
8
7
0
Register
17
X
PAFBA
6
5
4
3
2
1
B→A FIFO Almost-Full Flag Offset
2704 tbl 11
NOTE:
1. Bit 8 must be set to 0 for the IDT72605 (256 x 18) Synchronous BiFIFO.
Table 3. Flag Offset Register Format.
Number of Words
in FIFO
From
To
0
0
1
n
n+1
D-(m+1)
D-m
D-1
D
D
EF
PAE
PAF
FF
LOW
HIGH
HIGH
HIGH
HIGH
LOW
LOW
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
LOW
LOW
HIGH
HIGH
HIGH
HIGH
LOW
NOTES:
n = Programmable Empty Offset (PAEAB Register or PAEBA Register)
m = Programmable Full Offset (PAFAB Register or PAFBA Register)
D = FIFO Depth (IDT72605 = 256 words, IDT72615= 512 words)
2704 tbl 12
Table 4. Internal Flag Truth Table.
5.18
9
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
input register and the FIFO memory. If R/WB is HIGH and OEB
is LOW, data comes out of bus and is read from output register
into three-state buffer. In bypass mode, if R/WB is LOW,
bypass messages are transferred into B→A output register. If
R/WA is HIGH, bypass messages are transferred into A→B
output register. Refer to pin descriptions for more information.
R/WB
ENB
OEB
Data B
I/O
0
0
0
I
Data B is written on CLKB ↑. This write cycle immediately following output lowimpedance cycle is prohibited. Note that even though OEB = 0, a LOW logic level on
R/WB, once qualified by a rising edge on CLKB, will put Data B into a high-impedance
state.
0
0
1
I
Data B is written on CLKB ↑.
0
1
X
I
Data B is ignored
1
0
0
O
Data is read(1) from RAM array to output register on CLKB ≠, Data B is LOW
impedance
1
0
1
O
Data is read(1) from RAM array to output register on CLKB ≠, Data B is HIGH
impedance
1
1
0
O
Output register does not change(2), Data B is low-impedance
1
1
1
O
Output register does not change(2), Data B is high-impedance
Port B Operation
NOTES:
2704 tbl 13
1. When A2A1A0 = 000 or 1XX, the next A→B FIFO value is read out of the output register and the read pointer advances. If A2A1A0 = 001, the bypass
path is selected and bypass data is read from the Port B output register.
2. Regardless of the condition of A2A1A0, the data in the Port B output register does not change and the A→B read pointer does not advance.
Table 5. Port B Operation Control Signals.
5.18
10
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
t RS
RS
tRSF
EF AB,
PAE AB,
EF BA,
PAE BA
tRSF
EF AB,
PAE AB,
EF BA,
PAE BA
tRSS
tRSR
CSA,
EN A,
EN B
2704 drw 07
Figure 3. Reset Timing
tCLK
tCLKH
tCLKL
CLKA
A0 , A1 , A2 ,
R/WA
CSA
tCS
tCH
NO OPERATION
ENA
tFF
tFF
FFAB
tDS
tDH
DA0 -DA17
tSKEW1
CLKB
READ
DATA IN VALID
NO READ
OPERATION
2704 drw 08
Figure 4. Port A (A→B) Write Timing
5.18
11
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
tCLK
tCLKH
tCLKL
CLKA
A0 , A1 , A2 ,
R/WA
CSA
tCS
tCH
NO OPERATION
ENA
tEF
tEF
EFBA
tA
DA0 -DA17
VALID DATA
tOLZ
tOE
tOHZ
OE A
tSKEW1
CLKB
NO WRITE
WRITE
2704 drw 09
Figure 5. Port A (B→A) Read Timing
tCLK
tCLKH
tCLKL
CLKB
R/WB
tCS
tCH
NO OPERATION
ENB
tFF
tFF
FFBA
tDS
tDH
DB0 -DB17
tSKEW1
CLKA
DATA IN VALID
READ
NO READ
OPERATION
2704 drw 10
Figure 6. Port B (B→A) Write Timing
5.18
12
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
tCLK
tCLKH
tCLKL
CLKB
R/WB
tCS
tCH
NO OPERATION
ENB
tEF
tEF
EFAB
tA
DB0 -DB17
VALID DATA
tOLZ
tOE
tOHZ
OE B
tSKEW1
CLKA
NO WRITE
OPERATION
WRITE
2704 drw 11
Figure 7. Port B (A→B) Read Timing
5.18
13
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
CLKA
A0 , A1 , A2 ,
R/WA
tCS
CS A , ENA
t DS
DA0 -D A17
D0 (First valid write)
D1
D2
D3
tFRL
tSKEW1
(1)
CLKB
R/WB
tCS
ENB
t EF
EFAB
tA
DB0 -D B17
tA
D0
D1
t OLZ
t OE
OE B
2704 drw 12
NOTE:
1. When tSKEW1 ≥ minimum specification, tFRL(Max.) = tCLK + tSKEW1
tSKEW1 < minimum specification, tFRL(Max.) = 2tCLK + tSKEW1 or tCLK + tSKEW1
The Latency Timing applies only at the Empty Boundary (EF = LOW).
Figure 8. A→B First Data Word Latency after Reset for Simultaneous Read and Write
5.18
14
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
CLKB
R/WB
tCS
ENB
t DS
DB0 -D B17
D0 (First valid write)
D1
D2
D3
tFRL
tSKEW1
(1)
CLKA
A0 , A1 , A2 ,
R/WA
tCS
CSA , ENA
t EF
EFBA
tA
DA0 -D A17
tA
D0
D1
t OLZ
t OE
OE A
2704 drw 13
NOTE:
1. When tSKEW1 ≥ minimum specification, tFRL(Max.) = tCLK + tSKEW1
tSKEW1 < minimum specification, tFRL(Max.) = 2tCLK + tSKEW1
The Latency Timing apply only at the Empty Boundary (EF = LOW).
Figure 9. B→A First Data Word Latency after Reset for Simultaneous Read and Write
5.18
15
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
CLKA
tCS
A0 , A1 , A2 ,
A2 , A1 , A0 , = 001
R/WA
tCH
CSA
t CS
t CH
ENA
tFF
tFF
tFF
BYPASS FLAG
FFAB
FIFO FLAG
t DS
DA0 -D A17
DATA INPUT
tSKEW1
tSKEW1
tSKEW1
CLKB
R/WB
tCS
ENB
t EF
EFAB
t EF
FIFO FLAG
t EF
BYPASS FLAG
FIFO FLAG
BYPB
tA
DB0 -D B17
DATA OUTPUT
t OLZ
t OE
t OHZ
OE B
2704 drw 14
NOTES:
1. When CSA is brought HIGH, A→B Bypass mode will switch to FIFO mode on the following CLKA LOW-to-HIGH transition.
2. After the bypass operation is completed, the BYPB goes from LOW-to-HIGH; this will reset all bypass flags. The bypass path becomes available for
the next bypass operation.
3. When A-side changed from bypass mode into FIFO mode, B-side only has one cycle to read the bypass data. On the next cycle, B-side will be
forced back to FIFO mode.
Figure 10. A→B Bypass Timing
5.18
16
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
CLKB
R/WB
tCS
tCH
ENB
t FF
t FF
FIFO FLAG
t FF
t FF
FFBA
BYPASS FLAG
BYPB
t DS
DATA INPUT
DB0 -DB17
tSKEW1
tSKEW1
tSKEW1
tSKEW1
CLKA
tCS
tCS
A2 , A1 , A0 , = 001
A0 , A1 , A2 ,
tCS
CSA
R/WA
tCS
ENA
t EF
EFBA
FIFO FLAG
tEF
tEF
BYPASS FLAG
tEF
FIFO FLAG
tA
DATA OUTPUT
DA0 -DA17
tOLZ
t OE
t OHZ
OE A
2704 drw 15
NOTES:
1. When CSA is brought HIGH, A→B Bypass mode will switch to FIFO mode on the following CLKA going LOW-to-HIGH.
2. After the bypass operation is completed, the BYPB goes from LOW-to-HIGH; this will reset all bypass flags. The bypass path becomes available for
the next bypass operation.
3. When A-side changed from bypass mode into FIFO mode, B-side only has one cycle to read the bypass data. On the next cycle, B-side will be
forced back to FIFO mode.
Figure 11. B→A Bypass Timing
5.18
17
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
t CLKH
COMMERCIAL TEMPERATURE RANGE
tCLKL
CLKA
t CS
ENA
(R/W A = 0)
PAE AB
tCH
n+1 words in FIFO
WRITE
n words in FIFO
tSKEW2
(1)
tPAE
t PAE
(2)
CLK B
tCS
ENA
(R/W B = 1)
tCH
2704 drw 16
READ
NOTES:
1. tSKEW2 the minimum time between a rising CLKA edge and a rising CLKB edge for PAEAB to change during that clock cycle. If the time between the
rising edge of CLKA and the rising edge of CLKB is less than tSKEW, then PAEAB may not go HIGH until the next CLKB rising edge.
2. If a read is performed on this rising edge of the read clock, there will be Empty + (n + 1) words in the FIFO when PAE goes LOW.
Figure 12. A→B Programmable Almost-Empty Flag Timing
t CLKH
tCLKL
(2)
CLKA
t CS
ENA
(R/W A = 0)
PAFAB
tCH
WRITE
Full - (m+1) words in FIFO
Full - m words in FIFO
tPAF
tPAF
CLK B
tCS
ENB
(R/W B = 1)
t CH
READ
2704 drw 17
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for PAFAB to change during that clock cycle. If the time between the
rising edge of CLKB and the rising edge of CLKA is less than tSKEW2, then PAFAB may not go HIGH until the next CLKA rising edge.
2. If a write is performed on this rising edge of the write clock, there will be Full - (m + 1) words in the FIFO when PAF goes LOW.
Figure 13. A→B Programmable Almost-Full Flag Timing
5.18
18
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
t CLKH
COMMERCIAL TEMPERATURE RANGE
tCLKL
CLKB
t CS
ENB
(R/W A = 0)
tCH
WRITE
n words in FIFO
PAEBA
tSKEW2
n+1 words in FIFO
(1)
tPAE
t PAE
(2)
CLK A
tCS
ENA
(R/W A = 1)
tCH
2704 drw 18
READ
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for PAEBA to change during that clock cycle. If the time between the
rising edge of CLKB and the rising edge of CLKA is less than tSKEW2, then PAEBA may not go HIGH until the next CLKA rising edge.
2. If a read is performed on this rising edge of the read clock, there will be Empty + (n - 1) words in the FIFO when PAE goes LOW.
Figure 14. B→A Programmable Almost-Empty Flag Timing
t CLKH
tCLKL
(2)
CLKB
t CS
ENB
(R/W A = 0)
PAFBA
tCH
WRITE
Full - (m+1) words in FIFO
Full - m words in FIFO
tSKEW2 (1)
tPAF
tPAF
CLK A
tCS
ENA
(R/W A = 1)
t CH
READ
2704 drw 19
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for PAFBA to change during that clock cycle. If the time between the
rising edge of CLKB and the rising edge of CLKA is less than tSKEW2, then PAFBA may not go HIGH until the next CLKA rising edge.
2. If a write is performed on this rising edge of the write clock, there will be Full - (m + 1) words in the FIFO when PAF goes LOW.
Figure 15. B→A Programmable Almost-Full Flag Timing
5.18
19
IDT72605/IDT72615 CMOS SyncBiFIFO
256 x 18 x 2 and 512 x 18 x 2
COMMERCIAL TEMPERATURE RANGE
ORDERING INFORMATION
IDT
XXXXX
X
Device Type Power
XX
Speed
X
Package
X
Process/
Temperature
Range
BLANK
Commercial (0°C to +70°C)
G
J
PF
68-pin PGA
68-pin PLCC
64-pin TQFP
20
25
35
50
Clock Cycle Time (t CLK ) in ns
L
Low Power
72605
72615
256 x 18 Parallel Synchronous Bidirectional FIFO
512 x 18 Parallel Synchronous Bidirectional FIFO
2704 drw 20
5.18
20
Similar pages