IDT IDTQS32390 Quickswitch products high-speed cmos quickswitch 16:8 multiplexer Datasheet

IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH® PRODUCTS
HIGH-SPEED CMOS QUICKSWITCH
16:8 MULTIPLEXER
FEATURES:
•
•
•
•
•
•
•
•
IDTQS32390
DESCRIPTION:
Enhanced N channel FET with no inherent diode to Vcc
16:8 multiplexer function with zero delay
Ω bidirectional switches connect inputs to outputs
5Ω
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
Direct bidirectional connection for mux, demux
Ω resistors for low noise
25Ω
Available in QSOP package
The QS32390 provides a 16:8 multiplexer logic switch. The QS32390 has
an internal 25Ω resistor to reduce reflection noise in high-speed applications. The enable inputs connect one of two inputs to the common I/O pin,
respectively. The multiplexer function can be used to select and route logic
signals for zero delay, isolate bus capacitance, form crossbar switches, etc.
Mux/Demux devices provide an order of magnitude faster speed than
equivalent logic devices.
The QS32390 is characterized for operation at -40°C to +85°C.
APPLICATIONS:
• Video, audio, graphics switching, muxing
• Hot-swapping, hot-docking
• Voltage translation (5V to 3.3V)
FUNCTIONAL BLOCK DIAGRAM
A0
AB0
A7
AB7
AEN
B0
B7
BEN
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
c
2011 Integrated Device Technology, Inc.
FEBRUARY 2011
1
DSC-5752/5
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS(1)
PIN CONFIGURATION
Symbol
Description
VTERM(2) Supply Voltage to Ground
Max
Unit
–0.5 to +7
V
A0
1
28
B0
2
27
AB0
3
26
AC Input Voltage (pulse width ≤ 20ns)
–3
V
4
25
B7
AB7
VAC
A1
IOUT
DC Output Current
120
mA
B1
5
24
A6
PMAX
Maximum Power Dissipation (TA = 85°C)
AB1
6
23
B6
TSTG
Storage Temperature
A2
VCC
A7
7
22
AB6
B2
8
21
A5
AB2
9
20
B5
A3
10
19
AB5
B3
11
18
A4
AB3
AEN
12
13
17
B4
16
AB4
GN
D
14
15
BEN
VTERM(3)
DC Switch Voltage Vs
VTERM(3) DC Input Voltage VIN
–0.5 to +7
V
–0.5 to +7
V
0.5
W
–65 to +150
°C
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. Vcc terminals.
3. All terminals except Vcc.
CAPACITANCE
(TA = +25°C, f = 1.0MHZ, VIN = 0V, VOUT = 0V)
QSOP
TOP VIEW
Pins
Typ.
Max. (1)
Unit
Control Pins
4
5
pF
pF
Quickswitch Channels
Demux
5
7
(Switch OFF)
Mux
9
10
NOTE:
1. This parameter is measured at characterization but not tested.
PIN DESCRIPTION
Pin Names
I/O
A0 - A9
I/O
Bus A
Description
B0 - B9
I/O
Bus B
AEN, BEN
I
Bus Switch Enable
FUNCTION TABLE(1)
AEN
BEN
B0 - B9
Function
H
H
Off
Off
Disconnect
L
H
On
Off
A to AB
H
L
Off
On
B to AB
L
L
On
On
A, B to AB
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
2
A0 - A9
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5.0V ±5%
Symbol
Parameter
Test Conditions
VIH
Input HIGH Level
Guaranteed Logic HIGH for Control Pins
VIL
Input LOW Level
Guaranteed Logic LOW for Control Pins
IIN
Input LeakageCurrent (Control Inputs)(2) 0V ≤ VIN ≤ VCC
IOZ
Off-State Output Current (Hi-Z)
Switch ON Resistance
RON(3)
VP
Pass Voltage(2)
Min.
Typ.(1)
Max.
Unit
2
—
—
V
—
—
0.8
V
—
—
±1
μA
0V ≤ VOUT ≤ VCC, Switches OFF
—
—
±1
μA
VCC = Min., VIN = 0V, ION = 30mA
VCC = Min., VIN = 2.4V, ION =15mA
VIN = VCC = 5V, IOUT = -5μA
15
15
3.7
20
19
4
35
40
4.2
Ω
NOTES:
1. Typical values are at VCC = 5.0V, TA = 25°C.
2. Pass Voltage is guaranteed but not production tested.
3. ROUT changed on March 8, 2002. See rear page for more information.
TYPICAL ON RESISTANCE vs VIN AT VCC = 5V
80
R ON
(ohms)
70
60
50
40
30
20
10
0
0.0
0.5
1.0
1.5
2.0
V IN
(Volts)
3
2.5
3.0
3.5
V
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
Test Conditions(1)
Parameter
Max.
Unit
ICCQ
Quiescent Power Supply Current
VCC = Max., VIN = GND or Vcc, f = 0
3
μA
ΔICC
Power Supply Current per Control Input HIGH (2)
VCC = Max., VIN = 3.4V, f = 0
1.5
mA
ICCD
Dynamic Power Supply Current per MHz(3)
VCC = Max., A, B, and AB pins open
0.25
mA/MHz
Control Inputs Toggling at 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TLL driven input (VIN = 3.4V, control inputs only). A, B, and AB pins do not contribute to ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A, B, and AB I/Os generate no
significant AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
TA = -40°C to +85°C, VCC = 5.0V ± 5%;
CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted.
Symbol
Parameter
tPLH
Data Propagation Delay (2,4)
tPHL
AxBx to CxDx, CxDx to AxBx
tPZH
Switch Turn-on Delay
tPZL
BE to Ax, Bx, Cx, Dx
tPHZ
Switch Turn-off Delay (2)
tPLZ
BE to Ax, Bx, Cx, Dx
Min. (1)
Typ.
Max.
Unit
—
—
1.25(3)
ns
1.5
—
7.5
ns
—
—
5.5
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The time constant for the switch alone is of the order of 1.25ns for CL = 50pF.
4. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. Since this time constant is much smaller
than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined
by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
4
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Blank
8
Tube or Tray
Tape and Reel
QG
Quarter Size Outline Package - Green
32390
High Speed CMOS QuickSwitch 16:8 Multiplexer
As per PCN L0201-02, the Output Resistance (RON) specifications have changed as of March 8, 2002. The original specifications were:
Parameter
RON
Description
Min.
Typ.
Max.
Unit
VCC = Min, VIN = 0V, ION = 30mA
20
28
40
Ω
VCC = Min, VIN = 2.4V, ION = 15mA
24
35
48
Datasheet Document History
02/09/2011
Pg. 5
Updated the ordering information by removing the "IDT" notation, non RoHS part and by adding
Tape and Reel information.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
5
for Tech Support:
[email protected]
Similar pages