Intersil IH5012CPE Virtual ground analog switch Datasheet

IH5009-5012, 5014,
5016-5020, 5022, 5024
CT
T
ODU CEMEN 7
R
P
Virtual Ground Analog Switch
4
E
A
T
L
LE
2-77
EP
4
O
R
4
S
D
0
OB
NDE
1-80
m
MME ications arris.co
O
C
l
E
h
p
Features
Description
R
@
p
NO ntral A entapp
c
e
C
:
l
ai 20 Volts Peak-to-Peak
all r Up
• Switches Analog C
Signals
to
The IH5009 series of analog switches were designed to fill
o em
May 1999
the need for an easy-to-use, inexpensive switch for both
industrial and military applications. Although low cost is a
primary design objective, performance and versatility have
not been sacrificed.
• Each Channel Complete - Interfaces with Most
Integrated Logic
• Switching Speeds Less Than 0.5µs
• ID(OFF) Less Than 500pA Typical at 70oC
Each package contains up to four channels of analog gating
and is designed to eliminate the need for an external driver.
The odd numbered devices are designed to be driven
directly from TTL open collector logic (15 volts) while the
even numbered devices are driven directly from low level
TTL logic (5 volts). Each channel simulates a SPDT switch.
SPST switch action is obtained by leaving the diode cathode
unconnected; for SPDT action, the cathode should be
grounded (0V). The parts are intended for high performance
multiplexing and commutating usage. A logic “0” turns the
channel ON and a logic “1” turns the channel OFF.
• Effective rDS(ON) - 5Ω to 50Ω
• Commercial and Military Temperature Range
Operation
Part Number Information
PART
NUMBER
CHANNELS
LOGIC
LEVEL
IH5009
4
+15
DD, PD
IH5010
4
+5
DD, PD
IH5011
4
+15
DE, PE
IH5012
4
+5
DE, PE
IH5014
3
+5
DD, PD
IH5016
3
+5
DE, PE
IH5017
2
+15
PA
M = MILITARY (-55oC to 125oC)
IH5018
2
+5
DD, PA
C = COMMERCIAL (0oC to 70oC)
IH5019
2
+15
DE, PA
IH5020
2
+5
DE, PA
IH5022
1
+5
DD, PA
IH5024
1
+5
PA
PACKAGE
PKG
NO.
IH50XX
M
DE
PACKAGE
PA - 8 LEAD PDIP
PD - 14 LEAD PDIP
PE - 16 LEAD PDIP
DD - 14 LEAD CERDIP
DE - 16 LEAD CERDIP
TEMPERATURE RANGE
BASIC PART NUMBER
NOTE: Mil-Temperature range (-55oC to 125oC) available in ceramic
packages only.
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright
© Harris Corporation 1999
4-1
File Number
3129.1
IH5009 Series
Functional Diagrams (Numbers in brackets refer to CERDIP Packages)
IH5009, IH5010
(14 LEAD CERDIP, 14 LEAD PDIP)
IH5011, IH5012
(16 LEAD CERDIP, 16 LEAD PDIP)
IH5014
(14 LEAD CERDIP, 14 LEAD PDIP)
IH5016
(16 LEAD CERDIP, 16 LEAD PDIP)
IH5017 (8 LEAD PDIP)
IH5018 (8 LEAD PDIP, 14 LEAD CERDIP)
IH5019, IH5020
(8 LEAD PDIP, 16 LEAD CERDIP)
IH5022
(8 LEAD PDIP, 14 LEAD CERDIP)
IH5024
(8 LEAD PDIP)
4-2
IH5009 Series
Absolute Maximum Ratings
Thermal Information
Positive Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
Negative Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . .-15V
Diode Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
Power Dissipation (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
Operating Conditions
Temperature Range
5009C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
5009M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: Dissipation rating assumes device is mounted with all leads welded or soldered to printed circuit board in ambient temperature below
75oC. For higher temperature, derate at rate of 5m/WoC.
Electrical Specifications
PARAMETER
(Per Channel)
(NOTE 1)
SYMBOL
(NOTE 4)
TEST
CONDITIONS
(NOTE 2)
TYPE
-55oC (M)
0oC (C)
MIN/MAX
25oC
TYP
MIN/MAX
125oC(M)
70oC (C)
MIN/MAX
UNITS
Input Current-ON
IIN(ON)
ALL
VIN = 0V, ID = 2mA
-
0.01
±0.5
100
µA
Input Current-OFF
IIN(OFF)
5V Logic Ckts
VIN = +4.5V,
VA = ±10V
-
0.04
±0.5
20
nA
Input Current-OFF
IIN(OFF)
15V Logic Ckts
VIN = +11V,
VA = ±10V
-
0.04
±0.5
20
nA
Channel Control
Voltage-ON
VIN(ON)
5V Logic Ckts
Note 3
0.5
-
0.5
0.5
V
Channel Control
Voltage-ON
VIN(ON)
15V Logic Ckts
Note 3
1.5
-
1.5
1.5
V
Channel Control
Voltage-OFF
VIN(OFF)
5V Logic Ckts
Note 3
-
-
4.5
4.5
V
Channel Control
Voltage-OFF
VIN(OFF)
15V Logic Ckts
Note 3
-
-
11.0
11.0
V
Leakage Current-OFF
ID(OFF)
5V Logic Ckts
VIN = +4.5V,
VA = ±10V
-
0.02
±0.5
20
nA
Leakage Current-OFF
ID(OFF)
15V Logic Ckts
VIN = +11V,
VA = ±10V
-
0.02
±0.5
20
nA
Leakage Current-ON
ID(ON)
5V Logic Ckts
VIN = 0V, IS = 1mA
-
0.30
±1.0
1000 (M)
200 (C)
nA
Leakage Current-ON
ID(ON)
15V Logic Ckts
VIN = 0V, IS = 1mA
-
0.10
±0.5
500 (M)
100 (C)
nA
Leakage Current-ON
ID(ON)
5V Logic Ckts
VIN = 0V, IS = 2mA
-
-
1.0
10
µA
Leakage Current-ON
ID(ON)
15V Logic Ckts
VIN = 0V, IS = 2mA
-
-
2.0
100
µA
Drain-Source
ON-Resistance
rDS(ON)
5V Logic Ckts
ID = 2mA, VIN = 0.5V
150
90
150
385 (M)
240 (C)
Ω
Drain-Source
ON-Resistance
rDS(ON)
15V Logic Ckts
ID = 2mA, VIN = 1.5V
100
80
100
250 (M)
160 (C)
Ω
Turn-ON Time
t(ON)
All
-
150
500
-
ns
Turn-OFF Time
t(OFF)
All
-
300
500
-
ns
Cross Talk
CT
All
-
120
-
-
dB
f = 100Hz
NOTES:
1. (OFF) and (ON) subscript notation refers to the conduction state of the FET switch for the given test.
2. Refer to Figure 1 for definition of terms.
3. VIN(ON) and VIN(OFF) are test conditions guaranteed by the tests of rDS(ON) and ID(OFF) respectively.
4. “5V Logic CKTS” applies to even-numbered devices. “15V Logic CKTS” applies to odd-numbered devices.
4-3
Similar pages