Vishay IL4218-X006 Optocoupler, phototriac output, high dv/dt, very low input current Datasheet

IL4216/IL4217/IL4218
Vishay Semiconductors
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
FEATURES
• High input sensitivity IFT = 1.3 mA
A 1
6 MT2
C 2
5 NC
• High static dV/dt 10000 V/µs, typical
4 MT1
• Inverse parallel SCRs provide commutating
dV/dt > 10 kV/ µs
NC 3
• 300 mA on-state current
• Very Low Leakage < 10 µA
• Isolation test voltage 5300 VRMS
i179041
• Lead (Pb)-free component
DESCRIPTION
The IL4216/IL4217/IL4218 consists of an AlGaAs IRLED
optically coupled to a pair of photosensitive non-zero
crossing SCR chips and are connected inversely parallel to
form a TRIAC. These three semiconductors are assembled
in a six pin 0.3 inch dual in-line package.
High input sensitivity is achieved by using an emitter follower
phototransistor and a cascaded SCR predriver resulting in
an LED trigger current of less than 1.3 mA (DC).
The IL4216/IL4217/IL4218 uses two discrete SCRs resulting
in a commutating dV/dt of greater than 10 kV/µs. The use of
a proprietary dV/dt clamp results in a static dV/dt of greater
than 10 kV/µs. This clamp circuit has a MOSFET that is
enhanced when high dV/dt spikes occur between MT1 and
MT2 of the TRIAC. The FET clamps the base of the
phototransistor when conducting, disabling the internal SCR
predriver.
The blocking voltage of up to 800 V permits control of off-line
voltages up to 240 VAC, with a safety factor more than two,
and is sufficient for as much as 380 VAC. Current handling
capability is up to 300 mA RMS, continuous at 25 °C.
The IL4216/IL4217/IL4218 isolates low-voltage logic from
120, 240, and 380 VAC lines to control resistive inductive, or
capacitive loads including motors solenoids, high current
thyristors or TRIAC and relays.
• Component in accordance to RoHS 2002/95/EC and
WEEE 2002/96/EC
APPLICATIONS
• Solid state relay
• Industrial controls
• Office equipment
• Consumer appliances
AGENCY APPROVALS
• UL1577, file no. E52744 system code J
• CSA 93751
• DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5 pending
available with option 1
• BSI IEC 60950; IEC 60065
• FIMKO
ORDER INFORMATION
PART
REMARKS
IL4216
600 V VDRM, DIP-6
IL4217
700 V VDRM, DIP-6
800 V VDRM, DIP-6
IL4218
IL4216-X006
600 V VDRM, DIP-6 400 mil (option 6)
IL4216-X009
600 V VDRM, SMD-6 (option 9)
IL4217-X007
700 V VDRM, SMD-6 (option 7)
IL4217-X009
700 V VDRM, SMD-6 (option 9)
IL4218-X006
800 V VDRM, DIP-6 400 mil (option 6)
IL4218-X007
800 V VDRM, SMD-6 (option 7)
IL4218-X009
800 V VDRM, SMD-6 (option 9)
Note
For additional information on the available options refer to option information.
Document Number: 83630
Rev. 1.4, 09-Jan-08
For technical questions, contact: [email protected]
www.vishay.com
1
IL4216/IL4217/IL4218
Vishay Semiconductors
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
ABSOLUTE MAXIMUM RATINGS
PARAMETER
(1)
TEST CONDITION
PART
SYMBOL
VALUE
UNIT
VR
IF
6.0
60
2.5
100
1.33
750
V
mA
A
mW
mW/°C
°C/W
600
700
800
300
3.0
300
6.6
150
V
V
V
mA
A
mW
mW/°C
°C/W
Creepage distance
≥ 7.0
mm
Clearance
≥ 7.0
mm
°C
INPUT
Reverse voltage
Forward current
Surge current
Power dissipation
Derate linearly from 25 °C
Thermal resistance
OUTPUT
IFSM
Pdiss
Rth
IL4216
IL4217
IL4218
Peak off-state voltage
RMS on-state current
Single cycle surge
Power dissipation
Derate linearly from 25 °C
Thermal resistance
COUPLER
VDRM
VDRM
VDRM
IDRM
ITSM
Pdiss
Rth
Storage temperature
Tstg
- 55 to + 150
Ambient temperature
Tamb
- 55 to + 100
°C
Isolation test voltage
VISO
5300
VRMS
VIO = 500 V, Tamb = 25 °C
RIO
≥ 1012
Ω
VIO = 500 V, Tamb = 100 °C
RIO
≥ 1011
Ω
5.0 s
Tsld
260
°C
Isolation resistance
Lead soldering temperature (2)
Notes
(1) T
amb = 25 °C, unless otherwise specified.
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum
ratings for extended periods of the time can adversely affect reliability.
(2) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
www.vishay.com
2
For technical questions, contact: [email protected]
Document Number: 83630
Rev. 1.4, 09-Jan-08
IL4216/IL4217/IL4218
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
Vishay Semiconductors
ELECTRICAL CHARACTERISTICS
PARAMETER
TEST CONDITION
PART
SYMBOL
MIN.
TYP.
MAX.
1.3
1.5
UNIT
INPUT
Forward voltage
IF = 20 mA
VF
Breakdown voltage
IR = 10 µA
VBR
Reverse current
Input capacitance
6.0
30
V
V
VR = 6.0 V
IR
0.1
VF = 0 V, f = 1.0 MHz
CIN
40
pF
RthjI
750
°C/W
Thermal resistance, junction to lead
10
µA
OUTPUT
Repetitive peak off-state voltage
IDRM = 100 µA
Off-state voltage
ID(RMS) = 70 µA
IL4216
VDRM
600
650
V
IL4217
VDRM
700
750
V
IL4218
VDRM
800
850
V
IL4216
VD(RMS)
424
460
V
IL4217
VD(RMS)
484
536
V
IL4218
VD(RMS)
565
613
Off-state current
VD = 600 V, Tamb = 100 °C
ID(RMS)
Reverse current
VR = 600 V, Tamb = 25 °C
On-state voltage
IT = 300 mA
On-state current
PF = 1.0, VT(RMS) = 1.7 V
ITM
Surge (non-repetitive, on-state current)
f = 50 Hz
ITSM
Holding current
VT = 3.0 V
IH
65
V
10
100
µA
IRMS
10
100
µA
VTM
1.7
3.0
V
300
mA
3.0
A
200
μA
Latching current
VT = 2.2 V
IL
5.0
LED trigger current
VAK = 5.0 V
IFT
0.7
VD = 0.67 VDRM, Tamb = 25 °C
dV/dtcr
10000
V/µs
VD = 0.67 VDRM, Tamb = 80 °C
dV/dtcr
5000
V/µs
VD = 0.67 VDRM,
dI/dtcrq ≤ 15 A/ms,
Tamb = 25 °C
dV/dtcrq
10000
V/µs
VD = 0.67 VDRM,
dI/dtcrq ≤ 15 A/ms,
Tamb = 80 °C
dV/dtcrq
5000
V/µs
IT = 300 mA
dI/dt
100
A/ms
RthjI
150
°C/W
0.8
pF
1.0
mA
Critical rate of rise of off-state voltage
Critical rate of rise of voltage at current
commutation
Off-state current
Thermal resistance, junction to lead
mA
1.3
mA
COUPLER
Capacitance (input to output)
f = 1.0 MHz, VIO = 0 V
CIO
Critical rate of rise of coupled
input to output voltage
IT = 0, VRM = VDM = 300 VAC
dV(IO)/dt
5000
Note
Tamb = 25 °C, unless otherwise specified.
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
Document Number: 83630
Rev. 1.4, 09-Jan-08
For technical questions, contact: [email protected]
www.vishay.com
3
IL4216/IL4217/IL4218
Vishay Semiconductors
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
POWER FACTOR CONSIDERATIONS
1
C S - Shunt Capacitance (µF)
C S (µF) = 0.0032 (µF) x 10 ^ (0.0066 I L (mA))
0.1
0.01
PF = 0.3
IF = 2.0 mA
0.001
0
50
100
150
200
250
300
350 400
I L - Load Current (mA)
iil4116_07
Fig. 3 - Shunt Capacitance vs. Load Current vs. Power Factor
2.0
1.8
NI Fth - Normalized LED
Trigger Current
A snubber is not needed to eliminate false operation of the
TRIAC driver because of the IL4216/IL4217/IL4218 high
static and commutating dV/dt with loads between 1 and 0.8
power factors. When inductive loads with power factors less
than 0.8 are being driven, include a RC snubber or a single
capacitor directly across the device to damp the peak
commutating dV/dt spike. Normally a commutating dV/dt
causes a turning-off device to stay on due to the stored
energy remaining in the turning-off device.
But in the case of a zero voltage crossing optotriac, the
commutating dV/dt spikes can inhibit one half of the TRIAC
from turning on. If the spike potential exceeds the inhibit
voltage of the zero cross detection circuit, half of the TRIAC
will be held-off and not turn-on. This hold-off condition can be
eliminated by using a snubber or capacitor placed directly
across the optotriac as shown in Figure 1. Note that the value
of the capacitor increases as a function of the load current.
The hold-off condition also can be eliminated by providing a
higher level of LED drive current. The higher LED drive
provides a larger photocurrent which causes. The
phototransistor to turn-on before the commutating spike has
activated the zero cross network. Figure 8 shows the
relationship of the LED drive for power factors of less than
1.0. The curve shows that if a device requires 1.5 mA for a
resistive load, then 1.8 times (2.7 mA) that amount would be
required to control an inductive load whose power factor is
less than 0.3.
1.6
1.4
1.2
I Fth Normalized to I Fth at PF = 1.0
1.0
0.8
0
0.2
0.4
0.6
0.8
1.0
1.2
PF - Power Factor
iil4116_08
Fig. 4 - Normalized LED Trigger Current
TYPICAL CHARACTERISTICS
Tamb = 25 °C, unless otherwise specified
35
1.4
1.3
VF - Forward Voltage (V)
IF - LED Current (mA)
30
25
20
15
10
5
0
1.0
iil4116_01
TA = 25 °C
1.1
1.0
0.9
TA = 100 °C
0.8
0.7
1.1
1.2
1.3
VF - LED Forward Voltage (V)
Fig. 5 - LED Forward Current vs. Forward Voltage
www.vishay.com
4
TA = - 55 °C
1.2
1.4
0.1
iil4116_02
1
10
I F - Forward Current (mA)
100
Fig. 6 - Forward Voltage vs. Forward Current
For technical questions, contact: [email protected]
Document Number: 83630
Rev. 1.4, 09-Jan-08
IL4216/IL4217/IL4218
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
300
τ
Duty Factor
0.005
0.01
0.02
1000
t
0.05
0.1
0.2
100
PLED - LED Power (mW)
I f(pk) - Peak LED Current (mA)
10000
Vishay Semiconductors
τ
DF = /t
0.5
10
10- 6
10
-5
10
-4
-3
10
10
-2
10
-1
0
1
10
10
200
150
100
50
0
- 60
iil4116_06
t - LED Pulse Duration (s)
iil4116_03
250
Fig. 7 - Peak LED Current vs. Duty Factor, τ
- 40
- 20
0
20
40
60
80
100
TA - Ambient Temperature (°C)
Fig. 10 - Maximum Output Power Dissipation
PLED - LED Power (mW)
150
100
50
0
- 60
- 40
iil4116_04
- 20
0
20
40
60
TA - Ambient Temperature (°C)
80
100
Fig. 8 - Maximum LED Power Dissipation
IT - On-Site Current - mA(RMS)
500
400
300
200
100
0
- 100
- 200
- 300
- 400
- 500
-3
iil4116_05
-2
-1
0
1
2
VT - On-State Voltage - V(RMS)
3
Fig. 9 - On-State Terminal Voltage vs. Terminal Current
Document Number: 83630
Rev. 1.4, 09-Jan-08
For technical questions, contact: [email protected]
www.vishay.com
5
IL4216/IL4217/IL4218
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
Vishay Semiconductors
PACKAGE DIMENSIONS in inches (millimeters)
3
2
1
4
5
6
Pin one ID
0.248 (6.30)
0.256 (6.50)
ISO method A
0.335 (8.50)
0.343 (8.70)
0.300 (7.62)
(0.45)
0.048
0.039
(1.00)
min.
typ.
0.022 (0.55)
0.130 (3.30)
0.150 (3.81)
18 °
4°
typ.
0.114 (2.90)
0.031 (0.80) min.
0.031 (0.80)
0.018 (0.45)
0.130 (3.0)
3° to 9°
0.035 (0.90)
0.022 (0.55)
0.100 (2.54) typ.
0.010 (0.25)
typ.
0.300 to 0.347
(7.62 to 8.81)
i178004
Option 6
Option 7
Option 9
0.407 (10.36)
0.391 (9.96)
0.307 (7.8)
0.291 (7.4)
0.300 (7.62)
typ.
0.375 (9.53)
0.395 (10.03 )
0.300 (7.62)
ref.
0.028 (0.7)
min.
0.315 (8.0)
min.
0.014 (0.35)
0.010 (0.25)
0.400 (10.16)
0.430 (10.92)
www.vishay.com
6
0.331 (8.4)
min.
0.406 (10.3)
max.
0.180 (4.6)
0.160 (4.1) 0.0040 (0.102)
0.0098 (0.249)
0.012 (0.30 ) typ.
0.020 (0.51 )
0.040 (1.02 )
15° max.
0.315 (8.00)
min.
For technical questions, contact: [email protected]
18450
Document Number: 83630
Rev. 1.4, 09-Jan-08
IL4216/IL4217/IL4218
Optocoupler, Phototriac Output,
High dV/dt, Very Low Input Current
Vishay Semiconductors
OZONE DEPLETING SUBSTANCES POLICY STATEMENT
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with
respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone
depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use
within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in
the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively.
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency
(EPA) in the USA.
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do
not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application by the
customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall
indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any
claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Document Number: 83630
Rev. 1.4, 09-Jan-08
For technical questions, contact: [email protected]
www.vishay.com
7
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
Similar pages