Seme LAB IP79M15AJ 0.5 amp negative voltage regulator Datasheet

IP120MA SERIES
IP120M
SERIES
IP79M00A SERIES
IP79M00 SERIES
0.5 AMP
NEGATIVE
VOLTAGE REGULATOR
!
2
1
3
FEATURES
Pin 1 – Ground
Pin 2 – VOUT
Case – VIN
Pin 1 – Ground
Pin 2 – VIN
Case – VOUT
H Package – TO–39
SMD Package - SMD1
CERAMIC SURFACE MOUNT
• OUTPUT CURRENT UP TO 0.5A
• OUTPUT VOLTAGES OF -5, -12, -15V
• 0.01% / V LINE REGULATION
• 0.3% / A LOAD REGULATION
GND
1
8
NC
• THERMAL OVERLOAD PROTECTION
NC
2
7
NC
• SHORT CIRCUIT PROTECTION
NC
3
6
VIN
• OUTPUT TRANSISTOR SOA PROTECTION
VOUT
4
5
NC
• 1% VOLTAGE TOLERANCE (–A VERSIONS)
8 Pin J Package
Order Information
Part
H–Pack
Number
(TO–39)
IP79MxxAzz
✔
IP79Mxxzz
✔
IP120MAzz–xx
✔
IP120Mzz–xx
✔
Note:
xx = Voltage Code
(05, 12, 15)
eg.
IP79M05J
DESCRIPTION
J–Pack SMD–Pack
Temp.
CERDIP
SMD1
Range
✔
✔
-55 to +150°C
✔
✔
”
✔
”
✔
”
zz = Package Code
(H, J)
IP120MAH–12
The IP120MA and IP79M00A series of voltage
regulators are fixed output regulators intended for
local, on-card voltage regulation. These devices are
available in -5, -12, and -15 volt options and are
capable of delivering in excess of 500mA over
temperature.
The A suffix devices are fully specified at 0.5A,
provide 0.01% / V line regulation, 0.3% / A load
regulation, and ±1% output voltage tolerance at room
temperature. Protection features include safe
operating area, current limiting and thermal
shutdown.
ABSOLUTE MAXIMUM RATINGS (TC = 25°C unless otherwise stated)
VI
DC Input Voltage
PD
Power Dissipation
RqJC
Thermal Resistance Junction to Case
RqJA
(for VO = -5, -12, -15V)
Thermal Resistance Junction to Ambient
-35V
Internally limited
– H Package
20°C / W
– SMD Package
TBA°C / W
– H Package
120°C / W
– J Package
119°C / W
TJ
Operating Junction Temperature Range
–55 to 150°C
Tstg
Storage Temperature
–65 to 150°C
Note 1. Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation
PMAX of 2W for the H–Package ,1.05W for the J–Package and 15W for the SG–Package.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Prelim. 9/00
IP120MA SERIES
IP120M
SERIES
IP79M00A SERIES
IP79M00 SERIES
ELECTRICAL CHARACTERISTICS
Parameter
Test Conditions
IO = 100mA
VO
Output Voltage
VIN = -10V
IP79M05A
IP120MA–05
Min.
Typ.
Max.
IP79M05
IP120M–05
Min.
Typ.
Max.
-4.95
-5.05
-4.8
-5.15
-4.75
PD £ PMAX
-4.85
IO = 350mA
VIN = -8V to -18V
TJ = -55 to 150°C
DVO
Load Regulation
IQ
Quiescent Current
IO = 5mA to 500mA
VIN = -10V
VIN = -10V
TJ = -55 to 150°C
IO = 350mA
TJ = -55 to 150°C
IO = 5mA to 500mA
DIQ
Quiescent Current VIN = -10V
IO = 200mA
Change
TJ = -55 to 150°C
Output Noise
Voltage
DVIN
DVO
Ripple Rejection
Dropout Voltage
Isc
Short Circuit
Current
Ipk
Peak Output
Current
Average Temperature
Coefficient of VO
f = 10Hz to 100kHz
f = 120Hz
VIN = -8V to -18V
IO = 300mA
IO = 100mA
TJ = -55 to 150°C
10
50
3
10
30
5
50
100
mV
1
2
2
mA
0.1
0.4
0.4
0.1
0.4
0.4
40
400
400
1
65
80
54
65
80
54
1.1
2.3
VIN = -35V
300
600
1.0
1.4
0.5
2.0
IO = 5mA
V
3
IO = 350mA
VIN = -10V
-5.25
mV
mA
VIN = -8V to -25V
TJ = -55 to 150°C
VN
-5.2
TJ = -55 to 150°C
VIN = -7V to -25V
Line Regulation
-5
IO = 5mA to 350mA
VIN = -7V to -25V
DVO
-5
Units
0.5
0.5
mV
dB
2.3
V
300
600
mA
1.0
1.6
A
0.5
mV
°C
1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF.
All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp
voltage changes due to changes in internal temperature must be taken into account separately.
£ 10ms, d £ 5%). Output
2) Test Conditions unless otherwise stated: TJ = 25°C
PMAX = 2W for H Package (TO–39)
PMAX = 1.05W for J Package (CERDIP)
PMAX = 15W for SMD1 Package (SMD1)
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Prelim. 9/00
IP120MA SERIES
IP120M
SERIES
IP79M00A SERIES
IP79M00 SERIES
ELECTRICAL CHARACTERISTICS
Parameter
Test Conditions
IO = 100mA
VO
IP79M12A
IP120MA–12
Min.
Typ.
Max.
Output Voltage
VIN = -19V
-11.88
VIN = -14.5V to -30V
-11.64
-12
IP79M12
IP120M–12
Min.
Typ.
Max.
-12.12
-11.5
-12.36
-11.4
-12
-12.5
IO = 5mA to 350mA
PD £ PMAX
Units
-12.6
V
TJ = -55 to 150°C
4
18
80
4
18
50
10
60
240
mV
1.5
3
3
mA
0.1
0.4
0.4
0.1
0.4
0.4
96
960
960
VIN = -14.5V to -30V
DVO
Line Regulation
IO = 350mA
VIN = -15V to -25V
TJ = -55 to 150°C
DVO
Load Regulation
IQ
Quiescent Current
IO = 5mA to 500mA
VIN = -19V
VIN = -19V
TJ = -55 to 150°C
IO = 350mA
TJ = -55 to 150°C
IO = 5mA to 500mA
DIQ
Quiescent Current VIN = -19V
IO = 200mA
Change
TJ = -55 to 150°C
mA
VIN = -14.5V to -30V
TJ = -55 to 150°C
VN
Output Noise
Voltage
DVIN
DVO
Ripple Rejection
Dropout Voltage
Isc
Short Circuit
Current
Ipk
Peak Output
Current
Average Temperature
Coefficient of VO
f = 10Hz to 100kHz
f = 120Hz
IO = 300mA
VIN = -15V to
IO = 100mA
-25V
TJ = -55 to 150°C
58
72
54
58
72
54
IO = 350mA
1.1
2.3
VIN = -35V
300
600
1.0
1.4
1.2
4.8
VIN = -19V
IO = 5mA
1.5
mV
0.5
0.5
mV
dB
2.3
V
300
600
mA
1.0
1.6
A
1.2
mV
°C
1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF.
All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp
voltage changes due to changes in internal temperature must be taken into account separately.
£ 10ms, d £ 5%). Output
2) Test Conditions unless otherwise stated: TJ = 25°C
PMAX = 2W for H Package (TO–39)
PMAX = 1.05W for J Package (CERDIP)
PMAX = 15W for SMD Package (SMD1)
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Prelim. 9/00
IP120MA SERIES
IP120M
SERIES
IP79M00A SERIES
IP79M00 SERIES
ELECTRICAL CHARACTERISTICS
Parameter
Test Conditions
IO = 100mA
VO
IP79M15A
IP120MA–15
Min.
Typ.
Max.
Output Voltage
VIN = -23V
-14.85
VIN = -17.5V to -30V
-14.55
-15
IP79M15
IP120M–15
Min.
Typ.
Max.
-15.15
-14.4
-15.45
-14.25
-15
-15.6
IO = 5mA to 350mA
PD £ PMAX
Units
-15.75
V
TJ = -55 to 150°C
4
22
80
4
22
50
12
75
240
mV
1.5
3
3
mA
0.1
0.4
0.4
0.1
0.4
0.4
120
1200
1200
VIN = -17.5V to -30V
DVO
Line Regulation
IO = 350mA
VIN = -18V to -28V
TJ = -55 to 150°C
DVO
Load Regulation
IQ
Quiescent Current
IO = 5mA to 500mA
VIN = -23V
VIN = -23V
TJ = -55 to 150°C
IO = 350mA
TJ = -55 to 150°C
IO = 5mA to 500mA
DIQ
Quiescent Current VIN = -23V
IO = 200mA
Change
TJ = -55 to 150°C
mA
VIN = -17.5V to -30V
TJ = -55 to 150°C
VN
Output Noise
Voltage
DVIN
DVO
Ripple Rejection
Dropout Voltage
Isc
Short Circuit
Current
Ipk
Peak Output
Current
Average Temperature
Coefficient of VO
f = 10Hz to 100kHz
f = 120Hz
IO = 300mA
VIN = -18.5V to
IO = 100mA
-28.5V
TJ = -55 to 150°C
57
70
54
57
70
54
IO = 350mA
1.1
2.3
VIN = -35V
300
600
1.0
1.4
1.5
6.0
VIN = -23V
IO = 5mA
1.5
mV
0.5
0.5
mV
dB
2.3
V
300
600
mA
1.0
1.6
A
1.5
mV
°C
1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF.
All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp
voltage changes due to changes in internal temperature must be taken into account separately.
£ 10ms, d £ 5%). Output
2) Test Conditions unless otherwise stated: TJ = 25°C
PMAX = 2W for H Package (TO–39)
PMAX = 1.05W for J Package (CERDIP)
PMAX = 15W for SMD Package (SMD1)
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Prelim. 9/00
Similar pages