ISSI IS43R83200D-6TL 8mx32, 16mx16, 32mx8 256mb ddr sdram Datasheet

IS43R83200D
IS43/46R16160D, IS43/46R32800D
JUNE 2012
8Mx32, 16Mx16, 32Mx8
256Mb DDR SDRAM
FEATURES
DEVICE OVERVIEW
• VDD and VDDQ: 2.5V ± 0.2V
• SSTL_2 compatible I/O
• Double-data rate architecture; two data transfers
per clock cycle
• Bidirectional, data strobe (DQS) is transmitted/
received with data, to be used in capturing data
at the receiver
• DQS is edge-aligned with data for READs and
centre-aligned with data for WRITEs
• Differential clock inputs (CK and CK)
• DLL aligns DQ and DQS transitions with CK
transitions
• Commands entered on each positive CK edge; data
and data mask referenced to both edges of DQS
• Four internal banks for concurrent operation
• Data Mask for write data. DM masks write data
at both rising and falling edges of data strobe
• Burst Length: 2, 4 and 8
• Burst Type: Sequential and Interleave mode
• Programmable CAS latency: 2, 2.5 and 3
• Auto Refresh and Self Refresh Modes
• Auto Precharge
• TRAS Lockout supported (tRAP = tRCD)
ISSI’s 256-Mbit DDR SDRAM achieves high speed data
transfer using pipeline architecture and two data word
accesses per clock cycle. The 268,435,456-bit memory
array is internally organized as four banks of 64Mb to
allow concurrent operations. The pipeline allows Read
and Write burst accesses to be virtually continuous, with
the option to concatenate or truncate the bursts. The
programmable features of burst length, burst sequence
and CAS latency enable further advantages. The device
is available in 8-bit, 16-bit and 32-bit data word size
Input data is registered on the I/O pins on both edges
of Data Strobe signal(s), while output data is referenced
to both edges of Data Strobe and both edges of CLK.
Commands are registered on the positive edges of CLK.
OPTIONS
• Configuration(s): 8Mx32, 16Mx16, 32Mx8
• Package(s):
144 Ball BGA (x32)
66-pin TSOP-II (x8, x16) and 60 Ball BGA (x8, x16)
• Lead-free package available
• Temperature Range:
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
Automotive, A1 (-40°C to +85°C)
Automotive, A2 (-40°C to +105°C)
An Auto Refresh mode is provided, along with a Self
Refresh mode. All I/Os are SSTL_2 compatible.
ADDRESS TABLE
Parameter
8M x 32
16M x 16
32M x 8
Configuration
2M x 32 x 4
banks
4M x 16 x 4
banks
8M x 8 x 4
banks
Bank Address
Pins
BA0, BA1
BA0, BA1
BA0, BA1
Autoprecharge A8/AP
Pins
A10/AP
A10/AP
Row Address
4K(A0 – A11)
8K(A0 – A12) 8K(A0 – A12)
Column
Address
512(A0 – A7,
A9)
512(A0 – A8)
1K(A0 – A9)
8K / 64ms
8K / 16ms
8K / 64ms
Refresh Count
Com./Ind./A1 4K / 64ms
A2
4K / 16ms
KEY TIMING PARAMETERS
Speed Grade
-5
-6 Units
Fck Max CL = 3
Fck Max CL = 2.5
Fck Max CL = 2
200
200
133
167
167
133
MHz
MHz
MHz
Copyright © 2012 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without
notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications
unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
1
IS43R83200D
IS43/46R16160D, IS43/46R32800D
FUNCTIONAL BLOCK DIAGRAM (x32)
CK
CK
CKE
CS
RAS
CAS
WE
COMMAND
DECODER
&
CLOCK
GENERATOR
32
Mode Registers and
Ext. Mode Registers
CONTROLLER
32
12
12
MULTIPLEXER
12
ROW
ADDRESS
LATCH
12
12
ROW
ADDRESS
BUFFER
VDD/VDDQ
DATA OUT
BUFFER
4096
4096
4096
4096
Vss/VssQ
32
MEMORY CELL
ARRAY
BANK 0
SENSE AMP I/O GATE
2
COLUMN
ADDRESS LATCH
DQS0-DQS3
2
ROW DECODER
REFRESH
COUNTER
I/O 0-31
4
SELF
14
DM0-DM3
32
REFRESH
CONTROLLER
REFRESH
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
BA0
BA1
4
DATA IN
BUFFER
512
(x 32)
BANK CONTROL LOGIC
9
BURST COUNTER
COLUMN
ADDRESS BUFFER
2
COLUMN DECODER
9
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
FUNCTIONAL BLOCK DIAGRAM (x16)
CK
CK
CKE
CS
RAS
CAS
WE
COMMAND
DECODER
&
CLOCK
GENERATOR
16
Mode Registers and
Ext. Mode Registers
CONTROLLER
16
13
13
MULTIPLEXER
13
ROW
ADDRESS
LATCH
13
13
ROW
ADDRESS
BUFFER
VDD/VDDQ
DATA OUT
BUFFER
8192
8192
8192
8192
Vss/VssQ
16
MEMORY CELL
ARRAY
BANK 0
SENSE AMP I/O GATE
2
COLUMN
ADDRESS LATCH
LDQS, UDQS
2
ROW DECODER
REFRESH
COUNTER
I/O 0-15
2
REFRESH
15
LDM, UDM
16
REFRESH
CONTROLLER
SELF
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
BA0
BA1
2
DATA IN
BUFFER
512
(x 16)
BANK CONTROL LOGIC
9
BURST COUNTER
COLUMN
ADDRESS BUFFER
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
COLUMN DECODER
9
3
IS43R83200D
IS43/46R16160D, IS43/46R32800D
PIN CONFIGURATIONS
66 pin TSOP - Type II for x8
VDD
1
66
VSS
DQ0
2
65
DQ7
VDDQ
3
64
VSSQ
NC
4
63
NC
DQ1
5
62
DQ6
VSSQ
6
61
VDDQ
NC
7
60
NC
DQ2
8
59
DQ5
VDDQ
9
58
VSSQ
NC
10
57
NC
DQ3
11
56
DQ4
VSSQ
12
55
VDDQ
NC
13
54
NC
NC
14
53
NC
VDDQ
15
52
VSSQ
NC
16
51
DQS
NC
17
50
NC
VDD
18
49
VREF
NC
19
48
VSS
NC
20
47
DM
WE
21
46
CK
CAS
22
45
CK
RAS
23
44
CKE
CS
24
43
NC
NC
25
42
A12
BA0
26
41
A11
BA1
27
40
A9
A10/AP
28
39
A8
A0
29
38
A7
A1
30
37
A6
A2
31
36
A5
A3
32
35
A4
VDD
33
34
VSS
PIN DESCRIPTION: x8
A0-A12
Row Address Input
DM Data Write Mask
A0-A9
Column Address Input
DQS
Data Strobe
BA0, BA1
Bank Select Address
VDD
Power
DQ0 – DQ7
Data I/O
VDDQ
Power Supply for I/O Pins
CK, CK
System Clock Input
VSS
Ground
CKE
Clock Enable
VSSQ
Ground for I/O Pins
CS
Chip Select
VREF
SSTL_2 reference voltage
CAS
Column Address Strobe
Command
NC
No Connection
RAS
Row Address Strobe
Command
WE
Write Enable
4
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
PIN CONFIGURATION
Package Code B: 60-ball FBGA (top view) for x8
(8mm x 13mm Body, 0.8mm Ball Pitch)
Top View
(Balls seen through the Package)
: Ball Existing
: Depopulated Ball
Top View(See the balls through the Package)
1
2
3
7
8
9
DQ7
VSS
A
VDD
DQ0
VDDQ
NC
VDDQ
DQ6
B
DQ1
VSSQ
NC
NC
VSSQ
DQ5
C
DQ2
VDDQ
NC
NC
VDDQ
DQ4
D
DQ3
VSSQ
NC
D
NC
VSSQ
DQS
E
NC
VDDQ
NC
E
VREF
VSS
DM
F
NC
VDD
NC
CK
CK
G
WE
CAS
H
A12
CKE
H
RAS
CS
J
A11
A9
J
BA1
BA0
A8
A7
K
A0
A10/AP
A6
A5
L
A2
A1
A4
VSS
M
VDD
A3
1 2 3 4 5 6 7 8 9
A
B
C
VSSQ
F
G
K
L
M
BGA Package Ball Pattern
Top View
x 8 Device Ball Pattern
PIN DESCRIPTION: x8
A0-A12
Row Address Input
DQS
Data Strobe
A0-A9
Column Address Input
VDD
Power
BA0, BA1
Bank Select Address
VDDQ
Power Supply for I/O Pins
DQ0 – DQ7
Data I/O
VSS
Ground
CK, CK
System Clock Input
VSSQ
Ground for I/O Pins
CKE
Clock Enable
VREF
SSTL_2 reference voltage
CS
Chip Select
NC
No Connection
CAS
Column Address Strobe
Command
RAS
Row Address Strobe Command
WE
Write Enable
DM
Data Write Mask
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
5
IS43R83200D
IS43/46R16160D, IS43/46R32800D
PIN CONFIGURATIONS
66 pin TSOP - Type II for x16
VDD
1
66
VSS
DQ0
2
65
DQ15
VDDQ
3
64
VSSQ
DQ1
4
63
DQ14
DQ2
5
62
DQ13
VSSQ
6
61
VDDQ
DQ3
7
60
DQ12
DQ4
8
59
DQ11
VDDQ
9
58
VSSQ
DQ5
10
57
DQ10
DQ6
11
56
DQ9
VSSQ
12
55
VDDQ
DQ7
13
54
DQ8
NC
14
53
NC
VDDQ
15
52
VSSQ
LDQS
16
51
UDQS
NC
17
50
NC
VDD
18
49
VREF
NC
19
48
VSS
LDM
20
47
UDM
WE
21
46
CK
CAS
22
45
CK
RAS
23
44
CKE
CS
24
43
NC
NC
25
42
A12
BA0
26
41
A11
BA1
27
40
A9
A10/AP
28
39
A8
A0
29
38
A7
A1
30
37
A6
A2
31
36
A5
A3
32
35
A4
VDD
33
34
VSS
PIN DESCRIPTION: x16
A0-A12
Row Address Input
LDM, UDM Data Write Mask
A0-A8
Column Address Input
LDQS, UDQS
Data Strobe
BA0, BA1
Bank Select Address
VDD
Power
DQ0 – DQ15
Data I/O
VDDQ
Power Supply for I/O Pins
CK, CK
System Clock Input
VSS
Ground
CKE
Clock Enable
VSSQ
Ground for I/O Pins
CS
Chip Select
VREF
SSTL_2 reference voltage
CAS
Column Address Strobe
Command
NC
No Connection
RAS
Row Address Strobe
Command
WE
Write Enable
6
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
PIN CONFIGURATION
Package Code B: 60-ball FBGA (top view) for x16
(8mm x 13mm Body, 0.8mm Ball Pitch)
Top View
(Balls seen through the Package)
: Ball Existing
: Depopulated Ball
7
8
9
A
VDD
DQ0
VDDQ
DQ13
B
DQ2
VSSQ
DQ1
VSSQ
DQ11
C
DQ4
VDDQ
DQ3
DQ10
VDDQ
DQ9
D
DQ6
VSSQ
DQ5
D
DQ8
VSSQ
UDQS
E
LDQS VDDQ
DQ7
E
VREF
VSS
UDM
F
LDM
VDD
CK
CK
G
WE
CAS
H
A12
CKE
H
RAS
CS
J
A11
A9
J
BA1
BA0
A8
A7
K
A0
A10/AP
A6
A5
L
A2
A1
A4
VSS
M
VDD
A3
Top View(See the balls through the Package)
1 2 3 4 5 6 7 8 9
A
B
C
1
2
3
VSSQ
DQ15
VSS
DQ14
VDDQ
DQ12
F
G
K
L
M
BGA Package Ball Pattern
Top View
NC
x 16 Device Ball Pattern
PIN DESCRIPTION: x16
A0-A12
Row Address Input
LDQS, UDQS
Data Strobe
A0-A8
Column Address Input
VDD
Power
BA0, BA1
Bank Select Address
VDDQ
Power Supply for I/O Pins
DQ0 – DQ15
Data I/O
VSS
Ground
CK, CK
System Clock Input
VSSQ
Ground for I/O Pins
CKE
Clock Enable
VREF
SSTL_2 reference voltage
CS
Chip Select
NC
No Connection
CAS
Column Address Strobe
Command
RAS
Row Address Strobe Command
WE
Write Enable
LDM, UDM
Data Write Mask
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
7
IS43R83200D
IS43/46R16160D, IS43/46R32800D
PIN CONFIGURATION
Package Code B: 144-ball FBGA (top view)
(12mm x 12mm Body, 0.8mm Ball Pitch)
Top View (Balls seen through the package)
1 2 3 4 5 6 7 8 9 10 11 12
A
B
C
D
E
F
G
H
J
K
L
M
DQS0 DM0 VSSQ DQ3
DQ4 VDDQ
DQ6
NC
DQ2
DQ0 DQ31 DQ29 DQ28 VSSQ
VDDQ DQ1 VDDQ VDDQ DQ30 VDDQ
DQ5 VSSQ VSSQ VSSQ VDD
VSS VSSQ VSS
DQ7 VDDQ VDD
DM3 DQS3
VDDQ DQ27
NC
VDD VSSQ VSSQ VSSQ DQ26 DQ25
VSS VSSQ VSS
VDD VDDQ DQ24
DQ17 DQ16 VDDQ VSSQ VSS
VSS
VSS
VSS VSSQ VDDQ DQ15 DQ14
DQ19 DQ18 VDDQ VSSQ VSS
VSS
VSS
VSS VSSQ VDDQ DQ13 DQ12
VSSQ VSS
VSS
VSS
VSS VSSQ
DQ21 DQ20 VDDQ VSSQ VSS
VSS
VSS
VSS VSSQ VDDQ DQ11 DQ10
DQ22 DQ23 VDDQ VSSQ VSS
VSS
VSS
VSS VSSQ VDDQ
DQS2 DM2
NC
DM1 DQS1
NC
DQ9
DQ8
CAS
WE
VDD
VSS
A10
VDD
VDD
NC
VSS
VDD
NC
NC
RAS
NC
NC
BA1
A2
A11
A9
A5
NC
CK
CK
NC
CS
NC
BA0
A0
A1
A3
A4
A6
A7
A8
CKE VREF
Note: Vss balls inside the dotted box are optional for purposes of thermal dissipation.
PIN DESCRIPTION: for x32
A0-A11
Row Address Input
WE
Write Enable
A0-A7, A9
Column Address Input
DM0-DM3
Data Write Mask
BA0, BA1
Bank Select Address
DQS0-DQS3
Data Strobe
DQ0 – DQ31
Data I/O
VDD
Power
CK, CK
System Clock Input
VDDQ
Power Supply for I/O Pins
CKE
Clock Enable
VREF
SSTL_2 reference voltage
CS
Chip Select
VSS
Ground
CAS
Column Address Strobe
Command
VSSQ
Ground for I/O Pins
NC
No Connection
RAS
Row Address Strobe
Command
8
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
PIN FUNCTIONAL DESCRIPTIONS
Symbol
CK, CK
Type
Input
CKE
Input
CS
Input
RAS, CAS,
WE
DM: x8;
LDM, UDM:
x16;
DM0-DM3:
x32
Input
Input
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is
sampled HIGH along with that input data during a WRITE access. DM is sampled on both edges
of DQS. Although DM pins are input-only, the DM loading matches the DQ and DQS loading.
For x16 devices, LDM corresponds to the data on DQ0-DQ7, UDM corresponds to the data on
DQ8-DQ15.
BA0, BA1
Input
A [12:0]
Input
DQ:
DQ0-DQ7: x8;
DQ0-DQ15:
x16
DQ0-DQ31:
x32
DQS: x8:
I/O
I/O
LDQS, UDQS
x16:
DQS0-DQS3:
x32
NC
VREF
VDDQ
VSSQ
VDD
VSS
Description
Clock: CK and CK are differential clock inputs. All address and control input signals are sampled
on the crossing of the positive edge of CK and negative edge of CK. Input and output data is
referenced to the crossing of CK and CK (both directions of crossing). Internal clock signals are
derived from CK/ CK.
Clock Enable: CKE HIGH activates, and CKE LOW deactivates internal clock signals, and device
input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER-DOWN and
SELF REFRESH operation (all banks idle), or ACTIVE POWERDOWN (row ACTIVE in any
bank). CKE is synchronous for all functions except for SELF REFRESH EXIT, which is achieved
asynchronously. Input buffers, excluding CK, CK and CKE, are disabled during power-down and
self refresh mode which are contrived for low standby power consumption.
Chip Select: CS enables (registered LOW) and disables (registered HIGH) the command
decoder. All commands are masked when CS is registered HIGH. CS provides for external bank
selection on systems with multiple banks. CS is considered part of the command code.
Command Inputs: RAS, CAS and WE (along with CS) define the command being entered.
For x32 devices, DM0 corresponds to the data on DQ0-DQ7, DM1 corresponds to the data on
DQ8-DQ15, DM2 corresponds to the data on DQ16-DQ23, and DM3 corresponds to the data on
DQ24-DQ31.
Input Bank Address Inputs: BA0 and BA1 define to which bank an ACTIVE, READ, WRITE or
PRECHARGE command is being applied.
Address Inputs: provide the row address for ACTIVE commands, and the column address and
AUTO PRECHARGE bit for READ / WRITE commands, to select one location out of the memory
array in the respective bank. The address inputs also provide the opcode during a MODE
REGISTER SET command. A12 is not used for x32.
Data Bus: Input / Output
Data Strobe: Output with read data, input with write data. Edge-aligned with read data, centered
with write data. Used to capture write data.
For x16 device, LDQS corresponds to the data on DQ0-DQ7, UDQS corresponds to the data on
DQ8-DQ15.
-Supply
Supply
Supply
Supply
Supply
For x32 device, DQS0 corresponds to the data on DQ0-DQ7, DQS1 corresponds to the data on
DQ8-DQ15, DQS2 corresponds to the data on DQ16-DQ23, and DQS3 corresponds to the data
on DQ24-DQ31.
No Connect: Should be left unconnected.
SSTL_2 reference voltage.
I/O Power Supply.
I/O Ground.
Power Supply.
Ground.
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
9
IS43R83200D
IS43/46R16160D, IS43/46R32800D
COMMANDS TRUTH TABLES
All commands (address and control signals) are registered on the positive edge of clock (crossing of CK going high
and CK going low). Truth Table shows basic timing parameters for all commands.
TRUTH TABLE - COMMANDS
NAME (FUNCTION)
CS
RAS
CAS
WE
BA
AP
Address
Notes
DESELECT (NOP)
H
X
X
X
X
X
X
2
NO OPERATION (NOP)
L
H
H
H
X
X
X
2
ACTIVE (select bank and activate row)
L
L
H
H
Valid
X
Row
READ (select bank and column and start read
burst)
L
H
L
H
Valid
L
Column
READ with AP (read burst with Auto Precharge)
L
H
L
H
Valid
H
Column
WRITE (select bank and column and start write
burst)
L
H
L
L
Valid
L
Column
WRITE with AP (write burst with Auto
Precharge)
L
H
L
L
Valid
H
Column
3
BURST TERMINATE
L
H
H
L
X
X
X
4
PRECHARGE (deactivate row in selected
bank)
L
L
H
L
Valid
L
X
5
PRECHARGE ALL (deactivate rows in all
banks)
L
L
H
L
X
H
X
5
AUTO REFRESH or enter SELF REFRESH
L
L
L
H
X
X
X
6,7,8
MODE REGISTER SET
L
L
L
L
Valid
Op-code
3
9
Notes:
1. All states and sequences not shown are illegal or reserved.
2. DESELECT and NOP are functionally interchangeable.
3. Autoprecharge is non-persistent. AP High enables Auto Precharge, while AP Low disables Autoprecharge.
4. Burst Terminate applies to only Read bursts with Auto Precharge disabled. This command is undefined and should not be
used for Read with Auto Precharge enabled, and for Write bursts.
5. If AP is Low, bank address determines which bank is to be precharged. If AP is High, all banks are precharged and BA0BA1are don’t care.
6. This command is AUTO REFRESH if CKE is High, and SELF REFRESH if CKE is low.
7. All address inputs and I/O are ‘don't care’ except for CKE. Internal refresh counters control bank and row addressing.
8. All banks must be precharged before issuing an AUTO-REFRESH or SELF REFRESH command.
9. BA0 and BA1 value select between MRS and EMRS.
10. CKE is HIGH for all commands shown except SELF REFRESH.
ADDRESSING
TRUTH TABLE - DM Operations
FUNCTION
DM
DQ
Write Enable
L
Valid
Write Inhibit
H
X
Note: Used to mask write data, provided coincident with the
corresponding data.
10
x32
x16
x8
A8
A10
A10
Row Address (RA)
A0-A11
A0-A12
A0-A12
Column Address (CA)
A0-A7,
A9
A0-A8
A0-A9
Auto Precharge (AP)
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
TRUTH TABLE - CKE
CKE n-1
CKE n Current State
COMMAND n
ACTION n
NOTES
L
L
Power Down
X
Maintain Power Down
L
L
Self Refresh
X
Maintain Self Refresh
L
H
Power Down
NOP or DESELECT
Exit Power Down
6
L
H
Self Refresh
NOP or DESELECT
Exit Self Refresh
6, 7
H
L
All Banks Idle
NOP or DESELECT
Precharge Power Down Entry
6
H
L
Bank(s) Active
NOP or DESELECT
Active Power Down Entry
6
H
L
All Banks Idle
AUTO REFRESH
Self Refresh entry
H
H
See Truth Tables - Commands
Notes:
1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge.
2. Current state is the state of DDR immediately prior to clock edge n.
3. COMMANDn is the command registered at clock edge n, and ACTIONn is the result of COMMANDn.
4. All states and sequences not shown are illegal or reserved.
5. CKE must not go LOW during a Read or Write, and must stay HIGH until after trpst or twr, respectively.
6. DESELECT and NOP are functionally interchangeable.
7. NOPs or Deselects must be issued for at least tsnr after Self-Refresh exit before any other command. After DLL Reset, at
least txsrd must elapse before any Read commands occur.
Basic Timing Parameters for Commands
tCK
tCH
tCL
CK
CK
Input
tIS tIH
Valid
Valid
Valid
= Don't Care
NOTE: Input = A0 - An, BA0, BA1, CKE, CS, RAS, CAS, WE;
An = Address bus MSB
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
11
IS43R83200D
IS43/46R16160D, IS43/46R32800D
SIMPLIFIED STATE DIAGRAM
Power
Applied
Power
On
Precharge
PREALL
Self
Refresh
REFS
REFSX
MRS
EMRS
MRS
REFA
Idle
CKEH
Active
Power
Down
Auto
Refresh
CKEL
ACT
Precharge
Power
Down
CKEH
CKEL
Burst Stop
Row
Active
Write
Read
Write
Read
Write A
Write
Read A
Read
Read
Read A
Write A
PRE
Write
A
PRE
PRE
PRE
Read
A
Read
A
Precharge
PREALL
Automatic Sequence
Command Sequence
PREALL = Precharge All Banks
REFS = Enter Self Refresh
CKEL = Enter Power Down
Write A = Write with Autoprecharge
MRS = Mode Register Set
REFSX = Exit Self Refresh
CKEH = Exit Power Down
Read A = Read with Autoprecharge
EMRS = Extended Mode Register Set
REFA = Auto Refresh
ACT = Active
PRE = Precharge
12
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
FUNCTIONAL DESCRIPTION
The DDR SDRAM is a high speed CMOS, dynamic random-access memory internally configured as a quad-bank
DRAM. The 256Mb devices contains: 268,435,456 bits.
The DDR SDRAM uses double data rate architecture to achieve high speed operation. The double data rate
architecture is essentially a 2n prefetch architecture with an interface designed to transfer two data words per clock
cycle at the I/O pins. A single read or write access for the DDR SDRAM effectively consists of a single 2n-bit wide,
one clock cycle data transfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle
data transfers at the I/O pins. Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a
selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin
with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address
bits registered coincident with the ACTIVE command are used to select the bank and the row to be accessed. The
address bits registered coincident with the READ or WRITE command are used to select the bank and the starting
column location for the burst access.
Prior to normal operation, the DDR SDRAM must be initialized. The following section provides detailed information
covering device initialization, register definition, command description and device operation
INITIALIZATION
DDR SDRAMs must be powered up and initialized in a predefined manner. Operations procedures other than those
specified may result in undefined operation. If there is any interruption to the device power, the initialization routine
should be followed. The steps to be followed for device initialization are listed below. The Initialization Flow diagram
and the Initialization Flow sequence are shown in the following figures.
The Mode Register and Extended Mode Register do not have default values. If they are not programmed during the
initialization sequence, it may lead to unspecified operation. The clock stop feature is not available until the device has
been properly initialized from Step 1 through 13.
• Step 1: Apply VDD before or at the same time as VDDQ.
• Step 2: CKE must maintain LVCMOS Low until VREF is stable. Apply VDDQ before applying VTT and VREF.
• Step 3: There must be at least 200 μs of valid clocks before any command may be given to the DRAM. During this
time NOP or DESELECT commands must be issued on the command bus and CKE should be brought HIGH.
• Step 4: Issue a PRECHARGE ALL command.
• Step 5: Provide NOPs or DESELECT commands for at least tRP time.
• Step 6: Issue EMRS command
• Step 7: Issue MRS command, load the base mode register and to reset the DLL. Set the desired operating modes.
• Step 8: Provide NOPs or DESELECT commands for at least tMRD time.
• Step 9: Issue a PRECHARGE ALL command
• Step 10: Issue 2 or more AUTO REFRESH cycles
• Step 11: Issue MRS command with the reset DLL bit deactivated to program operating parameters without resetting
the DLL
• Step 12: Provide NOP or DESELECT commands for at least tMRD time.
• Step 13: The DRAM has been properly initialized and is ready for any valid command.
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
13
IS43R83200D
IS43/46R16160D, IS43/46R32800D
Initialization Waveform Sequence
VDD
VDDQ
tVDT≥ 0
VTT
(system1)
VREF
tCK
tCH
CK
CK
CKE
COMMAND
DM
tCL
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
tIS tIH
LVCMOS LOW LEVEL ( (
))
((
))
((
))
tIS tIH
NOP
PRE
((
))
AP4
BA0, BA1
ALL BANKS
((
))
tIS tIH
((
))
tIS tIH
MRS
PRE
((
))
((
))
AR
((
))
((
))
AR
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
CODE
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
CODE
BA0=L,
BA1=L
((
))
ALL BANKS
tIS tIH
MRS
ACT
CODE
RA
CODE
RA
BA0=L,
BA1=L
BA
((
))
((
))
((
))
tIS tIH
((
))
((
))
((
))
((
))
BA0=H,
BA1=L
((
))
((
))
((
))
((
))
CODE
((
))
((
))
((
))
((
))
CODE
((
))
((
))
((
))
((
))
tIS tIH
Address
((
))
((
))
((
))
EMRS
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
((
))
DQS
((
))
High--Z
((
))
((
))
((
))
((
))
((
))
DQ
((
))
High--Z
((
))
((
))
((
))
((
))
((
))
T = 200 µs
tMRD 2
Power--up:
VDD and
CLK stable
Extended
Mode
Register
Set
tMRD2
tRP
200 cycles of CK**
Load
Mode
Register,
Reset DLL
(with AP = H)
tRFC
tRFC
tMRD 2
Load
Mode
Register
(with AP= L)
DON’T CARE
Notes:
1. VTT is not applied directly to the device, however tVTD must be greater than or equal to zero to avoid device latch--up.
2. tMRD is required before any command can be applied, and 200 cycles of CK are required before any executable command
can be applied
3. The two Auto Refresh commands may be moved to follow the first MRS but precede the second PRECHARGE ALL command.
4. AP is A8 for x32, and A10 for x8/x16. Address is A0 to A12 except AP.
14
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
MODE REGISTER (MR) DEFINITION
The Mode Register is used to define the specific mode of operation of the DDR SDRAM. This definition includes
the definition of a burst length, a burst type, and a CAS latency. The Mode Register is programmed via the MODE
REGISTER SET command (with BA0=0 and BA1=0) and will retain the stored information until it is reprogrammed,
or the device loses power. Mode Register bits A0-A2 specify the burst length, A3 the type of burst (sequential or
interleave), A4-A6 the CAS latency, and A8 DLL reset. A logic 0 should be programmed to all the undefined addresses
bits to ensure future compatibility. The Mode Register must be loaded when all banks are idle and no bursts are in
progress, and the controller must wait the specified time tMRD before initiating any subsequent operation. Violating
either of these requirements will result in unspecified operation. Reserved states should not be used, as unknown
operation or incompatibility with future versions may result
Mode Register
BA1 BA0
A121
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Address Bus (Ax)
Mode Reg. (Ex)
A2 A1 A0 Burst Length
0 0 0 Reserved
0 0 1 2
0 1 0 4
0 1 1 8
1 0 0 Reserved
1 0 1 Reserved
1 1 0 Reserved
1 1 1 Reserved
A3 Burst Type
0 Sequential
1 Interleave
A12 A11 A10 A9 A8 A7 DLL
0
0
0
0 0 0 Normal operation
0
0
0
0 1 0 Reset DLL
BA1 BA0 Mode Register Definition
0
0 Program Mode Register
0
1 Program Extended Mode Register
1
0 Reserved
1
1 Reserved
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
A6 A5 A4 CAS Latency
0 0 0 Reserved
0 0 1 Reserved
0 1 0 2
0 1 1 3
1 0 0 Reserved
1 0 1 Reserved
1 1 0 2.5
1 1 1 Reserved
Notes:
1. A12 is not used in x32 and should be ignored for this option.
2. A logic 0 should be programmed to all unused / undefined
address bits to ensure future compatibility.
15
IS43R83200D
IS43/46R16160D, IS43/46R32800D
BURST LENGTH
Read and write accesses to the DDR SDRAM are burst oriented, with the burst length being set and the burst order
as in Burst Definition. The burst length determines the maximum number of column locations that can be accessed for
a given READ or WRITE command. Burst lengths of 2, 4, or 8 locations are available for both the sequential and the
interleaved burst types.
Burst Definition
Burst
Length
Starting Column Address
Order of Accesses Within a Burst
Type = Sequential
Type = Interleaved
0
0-1
0-1
1
1-0
1-0
A0
2
A1
A0
0
0
0-1-2-3
0-1-2-3
0
1
1-2-3-0
1-0-3-2
1
0
2-3-0-1
2-3-0-1
1
1
3-0-1-2
3-2-1-0
A2
A1
A0
0
0
0
0-1-2-3-4-5-6-7
0-1-2-3-4-5-6-7
0
0
1
1-2-3-4-5-6-7-0
1-0-3-2-5-4-7-6
0
1
0
2-3-4-5-6-7-0-1
2-3-0-1-6-7-4-5
0
1
1
3-4-5-6-7-0-1-2
3-2-1-0-7-6-5-4
1
0
0
4-5-6-7-0-1-2-3
4-5-6-7-0-1-2-3
1
0
1
5-6-7-0-1-2-3-4
5-4-7-6-1-0-3-2
1
1
0
6-7-0-1-2-3-4-5
6-7-4-5-2-3-0-1
1
1
1
7-0-1-2-3-4-5-6
7-6-5-4-3-2-1-0
4
8
Notes:
1. For a burst length of two, A1-An selects the two data element block; A0 selects the first access within the block.
2. For a burst length of four, A2-An selects the four data element block; A0-A1 selects the first access within the block.
3. For a burst length of eight, A3-An selects the eight data element block; A0-A2 selects the first access within the block.
4. Whenever a boundary of the block is reached within a given sequence, the following access wraps within the block.
16
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All
accesses for that burst take place within the block, meaning that the burst will wrap within the block if a boundary is
reached.
The block is uniquely selected by A1-An when the burst length is set to two, by A2-An when the burst length is set
to 4, by A3-An when the burst length is set to 8. An is the most significant column address bit, which depends if the
device is x8, x16 or x32. An = A9 for x8, An = A8 for x16 and An = A9 for x32. The programmed burst length applies to
both read and write bursts.
BURST TYPE
Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the
burst type and is selected via bit A3.
The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column
address.
READ LATENCY
The READ latency, or CAS latency, is the delay between the registration of a READ command and the availability of
the first piece of output data.
If a READ command is registered at a clock edge n and the latency is 3 clocks, the first data element will be valid at
n + 2tCK + tAC. If a READ command is registered at a clock edge n and the latency is 2 clocks, the first data element
will be valid at n + tCK + tAC.
OPERATING MODE
The normal operating mode is selected by issuing a Mode Register Set command with bits A7 to An each set to zero,
and bits A0 to A6 set to the desired values. A DLL reset is initiated by issuing a Mode Register Set command with
bits A7 and A9 to An each set to zero, bit A8 set to one, and bits A0 to A6 set to the desired values. A Mode Register
Set command issued to reset the DLL must always be followed by a Mode Register Set command to select normal
operating mode (A8=0).
All other combinations of values for A7 to An are reserved for future use and/or test modes. Test modes and reserved
states should not be used because unknown operation or incompatibility with future versions may result.
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
17
IS43R83200D
IS43/46R16160D, IS43/46R32800D
CAS LATENCIES
18
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
EXTENDED MODE REGISTER (EMR) DEFINITION
The Extended Mode Register controls functions beyond those controlled by the Mode Register; these additional
functions include DLL enable/disable, and output drive strength selection. The Extended Mode Register is
programmed via the MODE REGISTER SET command (with BA1=0 and BA0=1) and will retain the stored information
until it is reprogrammed, or the device loses power. The Extended Mode Register must be loaded when all banks
are idle and no bursts are in progress, and the controller must wait the specified time tMRD before initiating any
subsequent operation. Violating either of these requirements will result in unspecified operation. Reserved states
should not be used, as unknown operation or incompatibility with future versions may result.
DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during power-up initialization, and upon
returning to normal operation after having disabled the DLL for the purpose of debug or evaluation (upon exiting Self
Refresh Mode, the DLL is enabled automatically). Any time the DLL is enabled a DLL Reset must follow and 200 clock
cycles must occur before any executable command can be issued.
OUTPUT DRIVE STRENGTH (DS)
The normal drive strength for all outputs is specified to be SSTL_2, Class II. This DRAM also supports a reduced
driver strength option, intended for lighter load and/or point-to-point environments.
EXTENDED MODE REGISTER
BA1 BA0
A122
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Address Bus (Ax)
Ext. Mode Reg. (Ex)
Reserved(1)
A0 DLL
0 Enable
1 Disable
A1
0
1
BA1 BA0 Mode Register Definition
0
0 Program Mode Register
0
1 Program Extended Mode Register
1
0 Reserved
1
1 Reserved
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
Drive Strength
Normal
Reduced
NOTES:
1. A logic 0 should be programmed to all unused/undefined address bits to ensure future compatibility
2. A12 is not used for x32 and should be ignored for this option.
19
IS43R83200D
IS43/46R16160D, IS43/46R32800D
Absolute Maximum Rating
Parameter
Symbol
Value
Unit
Voltage on any pin relative to VSS
Vin, Vout
-1.0 ~ 3.6
V
Voltage on VDD & VDDQ supply relative to VSS
Vdd, Vddq
-1.0 ~ 3.6
Tstg
-55 ~ +150
Power dissipation
Pd
1.5
W
Short circuit current
Ios
50
mA
Storage temperature
V
o
C
Note:
Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommend operation condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability
AC/DC Electrical Characteristics and Operating Conditions
Recommended operating conditions (Voltage referenced to VSS=0V; TA=0 to 70oC for Commercial, TA = -40oC to +85oC for Industrial and A1,
TA = -40oC to +105oC for A2)
Parameter
Supply voltage (with a nominal VDD of 2.5V)
I/O Supply voltage (with a nominal VDD of 2.5V)
I/O Reference voltage
I/O Termination voltage (system)
Input logic high voltage
Input logic low voltage
Input Voltage Level, CLK and CLK inputs
Input Differential Voltage, CLK and CLK inputs
V-I Matching: Pullup to Pulldown Current Ratio
Input leakage current
Output leakage current
Output High Current (Normal strength driver) ; VOUT = VTT + 0.84V
Output Low Current (Normal strength driver) ; VOUT = VTT - 0.84V
Output High Current (Half strength driver); VOUT = VTT + 0.45V
Output Low Current (Half strength driver); VOUT = VTT - 0.45V
Ambient Operating Temperature
Commercial
Industrial
A1
A2
Symbol
Vdd
Vddq
Vref
Vtt
Vih(dc)
Vil(dc)
Vin(dc)
Vid(dc)
Vi(Ratio)
Il
Ioz
Ioh
Iol
Iohr
Iolr
Min
2.3
2.3
0.49*VDDQ
VREF-0.04
VREF+0.15
-0.3
-0.3
0.36
0.71
-2
-5
-16.8
16.8
-9
9
Max
2.7
2.7
0.51*VDDQ
VREF+0.04
VDDQ+0.3
VREF-0.15
VDDQ+0.3
VDDQ+0.6
1.4
2
5
–
–
–
–
Ta
Ta
Ta
Ta
0
-40
-40
-40
+70
+85
+85
+105
Unit
V
V
V
V
V
V
V
V
–
uA
uA
mA
mA
mA
mA
Note
1
2
3
4
C
C
o
C
o
C
o
o
Note :
1. VREF is expected to be equal to 0.5*VDDQ of the transmitting device, and to track variations in the dc level of same. Peak-to
peak noise on VREF may not exceed +/-2% of the dc value.
2. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to
VREF, and must track variations in the DC level of VREF
3. VID is the magnitude of the difference between the input level on CLK and the input level on CLK.
4. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire temperature and voltage range, for device drain to source voltages from 0.25V to 1.0V. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation. The full variation in the ratio of the maximum to
minimum pullup and pulldown current will not exceed 1.7 for device drain to source voltages from 0.1 to 1.0.
20
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
CAPACITANCE CHARACTERISTICS(1, 2)
(Vdd = Vddq = 2.5V + 0.2V, unless otherwise noted)
Symbol
Parameter
Test Condition
Limits
Units
Min
Max
CI(A)
Input Capacitance, address pin
VI=1.25v
1.3
3
pF
CI(C)
Input Capacitance, control pin
f=100MHz
1.3
3
pF
CI(K)
Input Capacitance, CLK pin
VI=25mVrms
1.3
3
pF
CI/O
I/O Capacitance, I/O, DQS, DM pin
3
5
pF
Notes:
1. This parameter is characterized.
2. Conditions: Frequency = 100MHz; Vout(DC) = Vdd/2; Vout(peak-to-peak) = 0.2V; Vref = Vss.
THERMAL RESISTANCE
Package
Substrate
Theta-ja
(Airflow = 0m/s)
Theta-ja
(Airflow = 1m/s)
Theta-ja
(Airflow = 2m/s)
Theta-jc
Units
TSOP2(66)
4-layer
69.7
61.2
57.5
12.7
C/W
BGA(60)
4-layer
40.1
36.5
34.2
7.9
C/W
BGA(144)
4-layer
29.4
29
27.1
4.5
C/W
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
21
IS43R83200D
IS43/46R16160D, IS43/46R32800D
IDD Specification Parameters and Test Conditions: x8, x16
(Vdd = Vddq = 2.5V ± 0.2V, Vss = VssQ = 0V, Output Open, unless otherwise noted)
Symbol
-5
-6
Units
IDD0
Operating current for one bank active-precharge; tRC = tRC(min);
tCK = tCK(min); DQ, DM and DQS inputs changing once per clock
cycle; address and control inputs changing once every two clock
cycles; CS = high between valid commands.
130
120
mA
IDD1
Operating current for one bank operation; one bank open, BL = 4,
tRC = tRC(min), tCK = tCK(min), Iout=0mA, Address and control
inputs changing once per clock cycle.
140
130
mA
IDD2P
Precharge power-down standby current; all banks idle; power-down
mode; CKE VIL(max); tCK = tCK(min); VIN = VREF for DQ, DQS and
DM
30
30
mA
IDD2F
Precharge floating standby current; CS VIH(min); all banks idle; CKE
VIH(min); tCK = tCK(min); address and other control inputs changing
once per clock cycle; VIN = VREF for DQ, DQS and DM
60
60
mA
IDD3P
Active power-down standby current; one bank active; power-down
mode; CKE VIL(max); tCK = tCK(min); VIN = VREF for DQ, DQS and
DM
35
35
mA
IDD3N
Active standby current; CS VIH(min); CKE VIH(min); one bank
active; tRC = tRAS(max); tCK = tCK(min); DQ, DQS and DM inputs
changing twice per clock cycle; address and other control inputs
changing once per clock cycle
75
75
mA
IDD4R
Operating current for burst read; burst length = 2; reads; continuous
burst; one bank active; address and control inputs changing once per
clock cycle; tCK = tCK(min); 50% of data changing on every transfer;
lOUT = 0mA
240
210
mA
IDD4W
Operating current for burst write; burst length = 2; writes; continuous
burst; one bank active address and control inputs changing once per
clock cycle; tCK = tCK(min); DQ, DM and DQS inputs changing twice
per clock cycle, 50% of input data changing at every transfer
260
220
mA
IDD5
Auto refresh current; tRC = tRFC(min);
140
140
mA
IDD6
Self refresh current; CKE 0.2V;
10
10
mA
IDD7
Operating current for four bank operation; four bank interleaving
330
READs (BL=4) with auto precharge; tRC = tRC(min), tCK = tCK(min);
Address and control inputs change only during ACTIVE, READ, or
WRITE commands
280
mA
22
Parameter/ Test Condition
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
IDD Specification Parameters and Test Conditions: x32
(Vdd = Vddq = 2.5V ± 0.2V, Vss = VssQ = 0V, Output Open, unless otherwise noted)
Symbol
Parameter/ Test Condition
-5
-6
Units
IDD0
Operating current for one bank active-precharge; tRC = tRC(min);
tCK = tCK(min); DQ, DM and DQS inputs changing once per clock
cycle; address and control inputs changing once every two clock
cycles; CS = high between valid commands.
180
160
mA
IDD1
Operating current for one bank operation; one bank open, BL = 4,
tRC = tRC(min), tCK = tCK(min), Iout=0mA, Address and control
inputs changing once per clock cycle.
190
170
mA
IDD2P
Precharge power-down standby current; all banks idle; power-down
mode; CKE VIL(max); tCK = tCK(min); VIN = VREF for DQ, DQS and
DM
35
35
mA
IDD2F
Precharge floating standby current; CS VIH(min); all banks idle; CKE
VIH(min); tCK = tCK(min); address and other control inputs changing
once per clock cycle; VIN = VREF for DQ, DQS and DM
65
65
mA
IDD3P
Active power-down standby current; one bank active; power-down
mode; CKE VIL(max); tCK = tCK(min); VIN = VREF for DQ, DQS and
DM
45
45
mA
IDD3N
Active standby current; CS VIH(min); CKE VIH(min); one bank
active; tRC = tRAS(max); tCK = tCK(min); DQ, DQS and DM inputs
changing twice per clock cycle; address and other control inputs
changing once per clock cycle
80
80
mA
IDD4R
Operating current for burst read; burst length = 2; reads; continuous
burst; one bank active; address and control inputs changing once per
clock cycle; tCK = tCK(min); 50% of data changing on every transfer;
lOUT = 0mA
330
300
mA
IDD4W
Operating current for burst write; burst length = 2; writes; continuous
burst; one bank active address and control inputs changing once per
clock cycle; tCK = tCK(min); DQ, DM and DQS inputs changing twice
per clock cycle, 50% of input data changing at every transfer
340
310
mA
IDD5
Auto refresh current; tRC = tRFC(min);
220
220
mA
IDD6
Self refresh current; CKE 0.2V;
10
10
mA
IDD7
Operating current for four bank operation; four bank interleaving
460
READs (BL=4) with auto precharge; tRC = tRC(min), tCK = tCK(min);
Address and control inputs change only during ACTIVE, READ, or
WRITE commands
430
mA
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
23
IS43R83200D
IS43/46R16160D, IS43/46R32800D
AC TIMING REQUIREMENTS
Absolute Specifications (VDD, VDDQ = +2.5 V ±0.2 V)
PARAMETER
SYMBOL
-5
-6
UNITS
MIN
MAX
MIN
MAX
DQ output access time for CLK,/CLK
tAC
-0.7
0.7
-0.7
0.7
ns
DQS output access time for CLK,/CLK
tDQSCK
-0.6
0.6
-0.6
0.6
ns
CLK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CLK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CLK half period
tHP
min
(tCL,tCH)
–
min
(tCL,tCH)
–
ns
CLK cycle time CL=3
tCK(3)
5
12
6
12
ns
CL=2.5
tCK(2.5)
5
12
6
12
ns
CL=2
tCK(2)
7.5
12
7.5
12
ns
DQ and DM input hold time
tDH
0.4
–
0.45
–
ns
DQ and DM input setup time
tDS
0.4
–
0.45
–
ns
Control & Address input pulse width (for each
input)
tIPW
2.2
–
2.2
–
ns
DQ and DM input pulse width (for each input)
tDIPW
1.75
–
1.75
–
ns
DQ & DQS high-impedance time from CLK,/CLK
tHZ
–
0.7
–
0.7
ns
DQ & DQS low--impedance time from CLK,/CLK
tLZ
-0.7
–
-0.7
–
ns
DQS--DQ Skew, DQS to last DQ valid, per group,
per access
tDQSQ
–
0.4
–
0.45
ns
DQ/DQS output hold time from DQS
tQH
tHP-tQHS
–
tHPtQHS
–
ns
Data Hold Skew Factor
tQHS
–
0.5
–
0.55
ns
Write command to first DQS latching transition
tDQSS
0.72
1.28
0.75
1.28
tCK
DQS input high pulse width
tDQSH
0.35
–
0.35
–
tCK
DQS input low pulse width
tDQSL
0.35
–
0.35
–
tCK
DQS falling edge to CLK setup time
tDSS
0.2
–
0.2
–
tCK
DQS falling edge hold time from CLK
tDSH
0.2
–
0.2
–
tCK
MODE REGISTER SET command cycle time
tMRD
2
–
2
–
tCK
Write preamble setup time
tWPRES
0
–
0
–
ns
Write postamble
tWPST
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.25
–
0.25
–
tCK
Address and Control input hold time (fast slew
rate)
tIHF
0.6
–
0.75
–
ns
Address and Control input setup time (fast slew
rate)
tISF
0.6
–
0.75
–
ns
Address and Control input hold time (slow slew
rate)
tIH
0.7
–
0.8
-–
ns
Address and Control input setup time (slow slew
rate)
tIS
0.7
–
0.8
–
ns
Read preamble
tRPRE
0.9
1.1
0.9
1.1
tCK
Read postamble
tRPST
0.4
0.6
0.4
0.6
tCK
ACTIVE to PRECHARGE command
tRAS
40
70,000
42
120,000
ns
24
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
AC TIMING REQUIREMENTS
Absolute Specifications (VDD, VDDQ = +2.5 V ±0.2 V@-5/-6)
PARAMETER
SYMBOL
-5
-6
UNITS
MIN
MAX
MIN
MAX
ACTIVE to ACTIVE/Auto Refresh command
period
tRC
55
–
60
–
ns
Auto Refresh to Active/Auto
tRFC
70
–
72
–
ns
ACTIVE to READ or WRITE delay
tRCD
15
–
15
–
ns
PRECHARGE command period
tRP
15
–
15
–
ns
Active to Autoprecharge Delay
tRAP
15
–
15
–
ns
ACTIVE bank A to ACTIVE bank B command
tRRD
10
–
12
–
ns
Write recovery time
tWR
15
–
15
–
ns
Auto Precharge write recovery + precharge time
tDAL
tWR+tRP
–
tWR+tRP
–
tCK
Internal Write to Read Command Delay
tWTR
2
–
1
–
tCK
Exit self refresh to non-READ
tXSNR
70
–
75
–
ns
Exit self refresh to READ command
tXSRD
200
–
200
–
tCK
Average Periodic Refresh Interval
(x8/x16)
Average Periodic Refresh Interval
(x32)
Ta ≤ 85 ºC
tREFI
–
7.8
–
7.8
ms
Ta > 85 ºC,
A2 only
tREFI
–
1.9
–
1.9
ms
Ta ≤ 85 ºC
tREFI
–
15.6
–
15.6
ms
Ta > 85 ºC,
A2 only
tREFI
–
3.9
–
3.9
ms
Output Load Condition
VREF
DQS
DQ
V TT =V REF
VREF
50 Ω
V OUT
Zo=50 Ω
30pF
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
V REF
Output Timing
Measurement
Reference Point
25
IS43R83200D
IS43/46R16160D, IS43/46R32800D
Notes:
1. All voltages referenced to Vss.
2. Tests for AC timing, IDD, and electrical, AC and DC characteristics, may be conducted at nominal reference/supply voltage
levels, but the related specifications and device operation are guaranteed for the full voltage range specified.
3. AC timing and IDD tests may use a VIL to VIH swing of up to 1.5V in the test environment, but input timing is still referenced to
VREF (or to the crossing point for CK//CK), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions. The minimum slew rate for the input signals is 1V/ns in the range between VIL(AC) and VIH(AC).
4. The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e. the receiver will effectively switch as a
result of the signal crossing the AC input level, and will remain in that state as long as the signal does not ring back above
(below) the DC input LOW (HIGH) level.
5. VREF is expected to be equal to 0.5*VddQ of the transmitting device, and to track variations in the DC level of the same.
Peak-to-peak noise on VREF may not exceed +2% of the DC value.
6. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to
VREF, and must track variations in the DC level of VREF.
7. VID is the magnitude of the difference between the input level on CLK and the input level on /CLK.
8. The value of VIX is expected to equal 0.5*VddQ of the transmitting device and must track variations in the DC level of the
same.
9. Enables on-chip refresh and address counters.
10. IDD specifications are tested after the device is properly initialized.
11. This parameter is sampled. VddQ = 2.5V+0.2V, Vdd = 2.5V + 0.2V , f = 100 MHz, Ta = 25°C, VOUT(DC) = VddQ/2,
VOUT(PEAK TO PEAK) = 25mV. DM inputs are grouped with I/O pins - reflecting the fact that they are matched in loading (to
facilitate trace matching at the board level).
12. The CLK//CLK input reference level (for timing referenced to CLK//CLK) is the point at which CLK and /CLK cross; the input
reference level for signals other than CLK//CLK, is VREF.
13. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period before VREF stabilizes, CKE< 0.3VddQ
is recognized as LOW.
14. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving (HZ), or begins driving (LZ).
15. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but
system performance (bus turnaround) will degrade accordingly.
16. The specific requirement is that DQS be valid (HIGH, LOW, or at some point on a valid transition) on or before this CLK
edge. A valid transition is defined as monotonic, and meeting the input slew rate specifications of the device. When no writes
were previously in progress on the bus, DQS will be transitioning from High-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS.
17. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM device.
18. tXPRD should be 200 tCLK in the condition of the unstable CLK operation during the power down mode.
19. For command/address and CK & /CK slew rate > 1.0V/ns.
20. Min (tCL,tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device.
21. For A2 temperature grade with TA > 85°C: IDD2F, IDD3N, and IDD7 are deregulated to 10% above these values; IDD2P and
IDD6 are deregulated to 20% above these values.
26
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
OUTPUT SLEW RATE CHARACTERISTICS
Slew Rate Characteristic
Typical Range
(V/ns)
Min
(V/ns)
Max
(V/ns)
Pullup Slew Rate
1.2-2.5
0.7
5.0
Pulldown Slew Rate
1.2-2.5
0.7
5.0
AC OVERSHOOT/UNDERSHOOT SPECIFICATION FOR ADDRESS AND CONTROL PINS
Parameter
Peak amplitude allowed for overshoot
Peak amplitude allowed for undershoot
Area between the overshoot signal and VDD must be less than or equal to (see figure below)
Area between the undershoot signal and GND must be less than or equal to (see figure below)
+5
+4
+3
Volts +2
(V) +1
0
-1
-2
-3
Max. amplitude = 1.5 V
Max
1.5
1.5
4.5
4.5
Units
V
V
V-ns
V-ns
Max
1.2
1.2
2.4
2.4
Units
V
V
V-ns
V-ns
Overshoot
VDD
Ground
Undershoot
Max. area = 4.5 V-ns
0
1
2
3
4
5
6
Time (ns)
Address and Control AC Overshoot and Undershoot Definition
Overshoot/Undershoot Specification for Data, Strobe, and Mask Pins
Parameter
Peak amplitude allowed for overshoot
Peak amplitude allowed for undershoot
Area between the overshoot signal and VDD must be less than or equal to (see figure below)
Area between the undershoot signal and GND must be less than or equal to (see figure below)
+5
+4
+3
Volts +2
(V) +1
0
-1
-2
-3
Max. amplitude = 1.2 V
Overshoot
VDD
Ground
Undershoot
Max. area = 2.4 V--ns
0
1
2
3
4
5
6
Time (ns)
DQ/DM/DQS AC Overshoot and Undershoot Definition
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
27
IS43R83200D
IS43/46R16160D, IS43/46R32800D
32Mx8 ORDERING INFORMATION - VDD = 2.5V
Commercial Range: 0°C to +70°C
Frequency
200 MHz
166 MHz
Speed (ns) 5
6
Order Part No.
IS43R83200D-5TL
IS43R83200D-6TL
Package
66-pin TSOP-II, Lead-free
66-pin TSOP-II, Lead-free
Industrial Range: -40°C to +85°C
Frequency
200 MHz
166 MHz
28
Speed (ns) 5
6
Order Part No.
IS43R83200D-5TLI
IS43R83200D-6TLI
Package
66-pin TSOP-II, Lead-free
66-pin TSOP-II, Lead-free
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
16Mx16 ORDERING INFORMATION - VDD = 2.5V
Commercial Range: 0°C to +70°C
Frequency
200 MHz
166 MHz
Speed (ns) 5
6
Order Part No.
IS43R16160D-5BL
IS43R16160D-5TL
IS43R16160D-6BL
IS43R16160D-6TL
Package
60-ball FBGA, Lead-free
66-pin TSOP-II, Lead-free
60-ball FBGA, Lead-free
66-pin TSOP-II, Lead-free
Industrial Range: -40°C to +85°C
Frequency
200 MHz
166 MHz
Speed (ns) 5
6
Order Part No.
IS43R16160D-5BLI
IS43R16160D-5BI
IS43R16160D-5TLI
IS43R16160D-6BLI
IS43R16160D-6BI
IS43R16160D-6TLI
Package
60-ball FBGA, Lead-free
60-ball FBGA
66-pin TSOP-II, Lead-free
60-ball FBGA, Lead-free
60-ball FBGA
66-pin TSOP-II, Lead-free
Automotive (A1) Range: -40°C to +85°C
Frequency
200 MHz
166 MHz
Speed (ns) 5
6
Order Part No.
IS46R16160D-5BLA1
IS46R16160D-5TLA1
IS46R16160D-6BLA1
IS46R16160D-6TLA1
Package
60-ball FBGA, Lead-free
66-pin TSOP-II, Lead-free
60-ball FBGA, Lead-free
66-pin TSOP-II, Lead-free
Automotive (A2) Range: -40°C to +105°C
Frequency
166 MHz
Speed (ns) 6
Order Part No.
IS46R16160D-6BLA2
IS46R16160D-6TLA2
Package
60-ball FBGA, Lead-free
66-pin TSOP-II, Lead-free
8Mx32 ORDERING INFORMATION - VDD = 2.5V
Commercial Range: 0°C to +70°C
Frequency
200 MHz
166 MHz
Speed (ns) 5
6
Order Part No.
IS43R32800D-5BL
IS43R32800D-6BL
Package
144-ball FBGA, Lead-free
144-ball FBGA, Lead-free
Industrial Range: -40°C to +85°C
Frequency
200 MHz
166 MHz
Speed (ns) 5
6
Order Part No.
IS43R32800D-5BLI
IS43R32800D-5BI
IS43R32800D-6BLI
Package
144-ball FBGA, Lead-free
144-ball FBGA
144-ball FBGA, Lead-free
Automotive (A1) Range: -40°C to +85°C
Frequency
166 MHz
Speed (ns) 6
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
Order Part No.
IS46R32800D-6BLA1
Package
144-ball FBGA, Lead-free
29
30
Θ
Package Outline
10/04/2006
4. Formed leads shall be planar with respect to one another within 0.1mm
at the seating plane after final test.
3. Dimension b does not include dambar protrusion/intrusion.
2. Dimension D and E1 do not include mold protrusion .
1. Controlling dimension : mm
NOTE :
IS43R83200D
IS43/46R16160D, IS43/46R32800D
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
IS43R83200D
IS43/46R16160D, IS43/46R32800D
Mini Ball Grid Array
Package Code: B (60-Ball) 8mm x 13mm
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
31
IS43R83200D
IS43/46R16160D, IS43/46R32800D
32
Integrated Silicon Solution, Inc.
Rev. B
06/19/2012
Similar pages