INTERSIL ISL28414

Single, Dual, Quad General Purpose Micropower, RRIO
Operational Amplifiers
ISL28114, ISL28214, ISL28414
Features
The ISL28114, ISL28214, and ISL28414 are single, dual, and
quad channel general purpose micropower, rail-to-rail input
and output operational amplifiers with supply voltage range of
1.8V to 5.5V. Key features are a low supply current of 360µA
maximum per channel at room temperature, a low bias
current and a wide input voltage range, which enables the
ISL28x14 devices to be excellent general purpose op-amps for
a wide range of applications.
• Low Current Consumption . . . . . . . . . . . . . . . . . . . . . . . 360µA
• Wide Supply Range . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 5.5V
• Gain Bandwidth Product . . . . . . . . . . . . . . . . . . . . . . . . . . 5MHz
• Input Bias Current . . . . . . . . . . . . . . . . . . . . . . . . . . 20pA, Max.
• Operating Temperature Range. . . . . . . . . . .-40°C to +125°C
• Packages
- ISL28114 (Single) . . . . . . . . . . . . . . . . . . . SC70-5, SOT23-5
- ISL28214 (Dual). . . . . . . . . . . . . . . . . . . . . . . . .MSOP8, SO8
- ISL28414 (Quad) . . . . . . . . . . . . . . . . . . . SOIC14, TSSOP14
The ISL28114 is available in the SC70-5 and SOT23-5
packages, the ISL28214 is in the MSOP8, SO8 packages, and
the ISL28414 is in the TSSOP14, SOIC14 packages. All devices
operate over the extended temperature range of -40°C to
+125°C.
Applications
Related Literature
• Power Supply Control/Regulation
• See AN1519 for “ISL28213/14SOICEVAL2Z Evaluation
Board User’s Guide”
• Signal Ban/Buffers
• Process Control
• See AN1520 for “ISL28113/14SOT23EVAL1Z Evaluation
Board User’s Guide”
• Active Filters
• See AN1542 for “ISL28213/14MSOPEVAL2Z Evaluation
Board User’s Guide”
• Trans-impedance Amp
• Current Shunt Sensing
• See AN1547 for “ISL28414TSSOPEVAL1Z Evaluation Board
User’s Guide”
RF
100kΩ
LOAD
RINRSENSE
IN-
10kΩ
RIN+
IN+
+5V
-
VOUT
V+
ISL28x14
V-
+
10kΩ
GAIN = 10
RREF+
100kΩ
VREF
SINGLE-SUPPLY, LOW-SIDE CURRENT SENSE AMPLIFIER
FIGURE 1. TYPICAL APPLICATION
June 23, 2011
FN6800.5
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2009-2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL28114, ISL28214, ISL28414
Ordering Information
PART NUMBER
(Notes 2, 3)
PART
MARKING
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL28114FEZ-T7 (Note 1)
BKA (Note 4)
5 Ld SC-70
P5.049
ISL28114FEZ-T7A (Note 1)
BKA (Note 4)
5 Ld SC-70
P5.049
Coming Soon
ISL28114FEV1Z-T7 (Note 1)
BMA (Note 4)
5 Ld SC-70
P5.049
Coming Soon
ISL28114FEV1Z-T7A (Note 1)
BMA (Note 4)
5 Ld SC-70
P5.049
ISL28114FHZ-T7 (Note 1)
BDBA (Note 4)
5 Ld SOT-23
P5.064A
ISL28114FHZ-T7A (Note 1)
BDBA (Note 4)
5 Ld SOT-23
P5.064A
ISL28214FUZ
8214Z
8 Ld MSOP
M8.118A
ISL28214FUZ-T7 (Note 1)
8214Z
8 Ld MSOP
M8.118A
ISL28214FBZ
28214 FBZ
8 Ld SOIC
M8.15E
ISL28214FBZ-T7 (Note 1)
28214 FBZ
8 Ld SOIC
M8.15E
ISL28214FBZ-T13 (Note 1)
28214 FBZ
8 Ld SOIC
M8.15E
ISL28414FVZ
28414 FVZ
14 Ld TSSOP
MDP0044
ISL28414FVZ-T7 (Note 1)
28414 FVZ
14 Ld TSSOP
MDP0044
ISL28414FVZ-T13 (Note 1)
28414 FVZ
14 Ld TSSOP
MDP0044
ISL28414FBZ
28414 FBZ
14 Ld SOIC
MDP0027
ISL28414FBZ-T7 (Note 1)
28414 FBZ
14 Ld SOIC
MDP0027
ISL28414FBZ-T13 (Note 1)
28414 FBZ
14 Ld SOIC
MDP0027
ISL28114SOT23EVAL1Z
Evaluation Board
ISL28214MSOPEVAL2Z
Evaluation Board
ISL28214SOICEVAL2Z
Evaluation Board
ISL28414TSSOPEVAL1Z
Evaluation Board
NOTES:
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL28114, ISL28214, ISL28414. For more information on MSL please
see Tech Brief TB363.
4. The part marking is located on the bottom of the part.
Pin Configurations
ISL28114FEZ
(5 LD SC-70)
TOP VIEW
IN+
1
VS-
2
IN-
3
5
4
ISL28114FEV1Z
(5 LD SC-70)
TOP VIEW
VS+
OUT
1
VS-
2
IN+
3
OUT
2
5
4
ISL28114
(5 LD SOT-23)
TOP VIEW
VS+
IN-
OUT
1
VS-
2
IN+
3
5
4
ISL28214
(8 LD MSOP, 8 LD SOIC)
TOP VIEW
VS+
IN-
OUT_A
1
8
VS+
IN-_A
2
7
OUT_B
IN+_A
3
6
IN-_B
VS-
4
5
IN+_B
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Pin Configurations (Continued)
ISL28414
(14 LD TSSOP, 14 LD SOIC)
TOP VIEW
14 OUT_D
OUT_A 1
IN-_A 2
13 IN-_D
IN+_A 3
12 IN+_D
11 VS-
VS+ 4
IN+_B 5
10 IN+_C
IN-_B 6
9 IN-_C
8 OUT_C
OUT_B 7
Pin Descriptions
PIN NO.
PIN
NAME
ISL28114FEZ
SC70-5
ISL28114FEV1Z
SC70-5
SOT23-5
OUT
OUT_A
OUT_B
OUT_C
OUT_D
4
1
1
MSOP8
SO8
TSSOP14
14 LD SOIC
1
7
1
7
8
14
DESCRIPTION
Output
V+
OUT
VCIRCUIT 1
VS-
2
2
2
4
11
Negative supply
voltage
V+
CAPACITIVELY
TRIGGERED
ESD CLAMP
VCIRCUIT 2
IN+
IN+_A
IN+_B
IN+_C
IN+_D
1
ININ-_A
IN-_B
IN-_C
IN-_D
3
VS+
5
3
Positive Input
3
3
5
4
3
5
V+
IN-
IN+
Negative Input
4
2
6
5
3
5
10
12
8
2
6
9
13
4
VCIRCUIT 3
Positive supply
voltage
See “CIRCUIT 2”
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5V
Supply Turn-on Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . .V- - 0.5V to V+ + 0.5V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V- - 0.5V to V+ + 0.5V
ESD Rating
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V
Machine Model (ISL28114, ISL28214) . . . . . . . . . . . . . . . . . . . . . . . 350V
Machine Model (ISL28414). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400V
Charged Device Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000V
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
5 Ld SC-70 (Notes 5, 6) . . . . . . . . . . . . . . . .
250
N/A
5 Ld SOT-23 (Notes 5, 6) . . . . . . . . . . . . . . .
225
N/A
8 Ld MSOP (Notes 5, 6) . . . . . . . . . . . . . . . .
180
100
8 Ld SOIC Package (Notes 5, 6) . . . . . . . . .
126
90
14 Ld TSSOP Package (Notes 5, 6) . . . . . .
120
40
14 Ld SOIC Package (Notes 5, 6) . . . . . . . .
90
50
Ambient Operating Temperature Range . . . . . . . . . . . . . .-40°C to +125°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+125°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
6. For θJC, the “case temp” location is taken at the package top center.
Electrical Specifications
VS+ = 5V, VS- = 0V, RL = Open, VCM = VS/2, TA = +25°C, unless otherwise specified. Boldface limits apply over
the operating temperature range, -40°C to +125°C, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 7)
TYP
MAX
(Note 7)
UNIT
-5
0.5
5
mV
6
mV
2
10
µV/°C
1
30
pA
3
20
pA
100
pA
20
pA
-50
50
pA
- 0.1
5.1
V
DC SPECIFICATIONS
VOS
Input Offset Voltage
-40°C to +125°C
TCVOS
Input Offset Voltage Temperature
Coefficient
IOS
Input Offset Current
IB
Input Bias Current
-6
-40°C to +125°C
ISL28114
-20
-100
ISL28214, ISL28414
Common Mode Input
Voltage Range
CMRR
PSRR
VOH
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Output Voltage Swing, High
-20
3
VCM = -0.1V to 5.1V
72
dB
-40°C to +125°C
70
dB
VS = 1.8V to 5.5V
71
dB
-40°C to +125°C
70
dB
4.993
V
RL = 10kΩ
4.985
4.98
VOL
Output Voltage Swing, Low
V+
Supply Voltage
IS
Supply Current per Amplifier
RL = 10kΩ
V
13
1.8
RL = OPEN
300
15
mV
20
mV
5.5
V
360
µA
400
µA
ISC+
Output Source Short Circuit Current RL = 10Ω to V-
-31
mA
ISC-
Output Sink Short Circuit Current
26
mA
4
RL = 10Ω to V+
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Electrical Specifications
VS+ = 5V, VS- = 0V, RL = Open, VCM = VS/2, TA = +25°C, unless otherwise specified. Boldface limits apply over
the operating temperature range, -40°C to +125°C, unless otherwise specified. (Continued)
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 7)
TYP
MAX
(Note 7)
UNIT
AC SPECIFICATIONS
GBWP
Gain Bandwidth Product
VS = ±2.5V
AV = 100, RF = 100kΩ,
RG = 1kΩ, RL = 10kΩ to VCM
5
MHz
eN VP-P
Peak-to-Peak Input Noise Voltage
VS = ±2.5V
f = 0.1Hz to 10Hz
12
µVP-P
eN
Input Noise Voltage Density
VS = ±2.5V
f = 1kHz
40
nV/√(Hz)
iN
Input Noise Current Density
VS = ±2.5V
f = 1kHz
8
fA/√(Hz)
ZIN
Input Impedance
1012
Ω
Cin
Differential Input Capacitance
VS = ±2.5V
f = 1MHz
1.0
pF
1.3
pF
Common Mode Input Capacitance
TRANSIENT RESPONSE
SR
Slew Rate
VOUT = 0.5V to 4.5V
2.5
V/µs
tr, tf, Small Signal
Rise Time, tr 10% to 90%
VS = ±2.5V
AV = +1, VOUT = 0.05VP-P,
RF = 0Ω, RL = 10kΩ, CL = 15pF
37
ns
42
ns
5.6
µs
Fall Time, tf 10% to 90%
ts
Settling Time to 0.1%, 4VP-P Step
VS = ±2.5V
AV = +1, RF = 0Ω, RL = 10kΩ,
CL = 1.2pF
NOTE:
7. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
5
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Typical Performance Curves
VS = ±2.5V, VCM = 0V, RL = Open, unless otherwise specified.
50
INPUT NOISE VOLTAGE (nV/√Hz)
10,000
40
30
10
0
-10
-20
-30
-40
SIMULATION
-50
-40
-20
0
20
40
60
80
100
120
1000
100
10
140
1
10
TEMPERATURE (°C)
1k
10k
100k
FIGURE 3. INPUT NOISE VOLTAGE SPECTRAL DENSITY
FIGURE 2. INPUT BIAS CURRENT vs TEMPERATURE
20
120
20
100
0
100
0
-20
GAIN
60
-40
40
-60
20
-80
0
-100
-20 V+ = ±0.9V
RL = 100k
-40
CL = 10pF
-60 SIMULATION
-80
0.1
1
10
-120
PHASE
-140
-160
100
1k
10k 100k
FREQUENCY (Hz)
1M
-180
10M 100M
FIGURE 4. OPEN-LOOP GAIN, PHASE vs FREQUENCY,
RL = 100kΩ, CL = 10pF, VS = ±0.9V
PHASE (°)
80
OPEN LOOP GAIN (dB)
120
80
-60
20
-80
0
-100
-20 V+ = ±0.9V
RL = 100k
-40
CL = 10pF
-60 SIMULATION
-80
0.1
70
80
60
70
30
0
0.01
10
-140
-160
100
1k
10k 100k
FREQUENCY (Hz)
1M
-180
10M 100M
PSRR+ VS = ±0.9V
PSRR+ VS = ±2.5V
PSRR- VS = ±2.5V
60
50
40
PSRR- VS = ±0.9V
30
RL = INF
20 C = 4pF
L
10 AV = +1
20
10
1
-120
PHASE
FIGURE 5. OPEN-LOOP GAIN, PHASE vs FREQUENCY,
RL = 100kΩ, CL = 10pF, VS = ±2.5V
90
40
-40
40
80
50
-20
GAIN
60
PSRR (dB)
CMRR (dB)
OPEN LOOP GAIN (dB)
100
FREQUENCY (Hz)
PHASE (°)
IBIAS (pA)
20
V+ = ±2.5V
AV = 1
SIMULATION
0.1
1
10
100 1k 10k 100k
FREQUENCY (Hz)
1M
10M 100M
FIGURE 6. CMRR vs FREQUENCY (SIMULATED DATA)
6
VCM = 100mVP-P
0
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
FIGURE 7. PSRR vs FREQUENCY, VS = ±0.9V, ±2.5V
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Typical Performance Curves
70
GAIN (dB)
AV = 100
V+ = ±2.5V
CL = 4pF
RL = 10k
VOUT = 50mVP-P
30
20
AV = 10
Rg = 10k, Rf = 100k
10
0
0
Rg = 1k, Rf = 100k
50
40
1
Rg = 100, Rf = 100k
AV = 1000
AV = 1
-10
10
NORMALIZED GAIN (dB)
60
VS = ±2.5V, VCM = 0V, RL = Open, unless otherwise specified. (Continued)
Rg = OPEN, Rf = 0
100
10k
1k
100k
1M
10M
100M
-1
-2
-3
-4
VOUT = 10mVP-P
-5
VOUT = 50mVP-P
-6 VS = ±2.5V
VOUT = 100mVP-P
-7 CL = 4pF
A = +1
-8 V
RL = 10k
-9
100
1k
VOUT = 200mVP-P
VOUT = 500mVP-P
VOUT = 1VP-P
10k
0
-1
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
10M
100M
7
1
-2
-3
-4
RL = 4.99k
-5
-6 V+ = ±2.5V
-7 CL = 4pF
AV = +1
-8
VOUT = 50mVP-P
-9
100
1k
10k
RL = 1k
RL = 499
CL = 1004pF
CL = 474pF
3
2
CL = 224pF
1
CL = 104pF
0
-1
CL = 26pF
-2
RL = 100
100k
VS = ±2.5V
6 RL = 10k
5 AV = +1
VOUT = 50mVP-P
4
1M
10M
-3
1k
100M
CL = 4pF
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 11. GAIN vs FREQUENCY vs CL
FIGURE 10. GAIN vs FREQUENCY vs RL
140
1
0
120
-1 CL = 4pF
RL = 10k
-2
AV = +1
-3 VOUT = 50mVP-P
CROSSTALK (dB)
NORMALIZED GAIN (dB)
1M
FIGURE 9. FREQUENCY RESPONSE vs VOUT
FIGURE 8. FREQUENCY RESPONSE vs CLOSED LOOP GAIN
-4
-5
VS = ±2.5V
-6
VS = ±1.75V
-7
VS = ±1.25V
-8
-9
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
1M
10M
100M
FREQUENCY (Hz)
FIGURE 12. GAIN vs FREQUENCY vs SUPPLY VOLTAGE
7
80
60
40
20
VS = ±0.9V
100k
100
0
10
VS = ±2.5V
RL-DRIVER = INF
RL-RECEIVER = 10k
CL = 4pF
AV = +1
VSOURCE = 1VP-P
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FIGURE 13. CROSSTALK, VS = ±2.5V
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
VS = ±2.5V, VCM = 0V, RL = Open, unless otherwise specified. (Continued)
30
3
20
2
10
LARGE SIGNAL (V)
VS = ±2.5V
RL = 10k
CL = 15pF
AV = +1
VOUT = 50mVP-P
0
-10
-20
1
VS = ±0.9V
0
RL = 10k
CL = 15pF
AV = +1
VOUT = RAIL
-1
-2
-30
-40
VS = ±2.5V
0
80
160
240
320
400
480
560
640
720
-3
800
0
1
2
3
4
TIME (ns)
INPUT (V)
-0.2
-0.3
0
0.5
-0.5
0.4
-1.0
-1.5
OUTPUT @ VS = ±0.9V
-0.4
0.6
OUTPUT @ VS = ±2.5V
-0.5
INPUT (V)
RL = INF
CL = 15pF
AV =10
Rf = 9.09k, Rg = 1k
-0.1
0.5
OUTPUT (V)
0
INPUT
7
8
9
10
FIGURE 15. LARGE SIGNAL TRANSIENT RESPONSE vs
RL VS = ±0.9V, ±2.5V
FIGURE 14. SMALL SIGNAL TRANSIENT RESPONSE, VS = ±2.5V
0.1
5
6
TIME (µs)
3.0
OUTPUT @ VS = ±2.5V
-2.5
0
1.5
RL = INF
CL = 15pF
AV =10
Rf = 9.09k, Rg = 1k
0.2
0.1
2.0
OUTPUT @ VS=±0.9V
0.3
-2.0
2.5
1.0
OUTPUT (V)
SMALL SIGNAL (mV)
Typical Performance Curves
0.5
0
INPUT
-0.6
0
0.4
0.8
1.2
1.6 2.0 2.4
TIME (ms)
2.8
3.3
-0.1
-3.0
4.0
3.6
0
0.4
0.8
1.2
1.6 2.0 2.4
TIME (ms)
2.8
3.3
3.6
-0.5
4.0
FIGURE 17. POSITIVE OUTPUT OVERLOAD RESPONSE TIME,
VS = ±0.9V, ±2.5V
FIGURE 16. NEGATIVE OUTPUT OVERLOAD RESPONSE TIME,
VS = ±0.9V, ±2.5V
VS = ±2.5V
70 RL = 10k
AV = 1
60 VOUT = 50mVP-P
O
T
+
50
O
T
-
SH
R
O
SH
R
VE
O
20
VE
30
O
40
O
OVERSHOOT (%)
80
10
0
10
100
1k
CAPACITANCE (pF)
10k
FIGURE 18. % OVERSHOOT vs LOAD CAPACITANCE, VS = ±2.5V
8
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Applications Information
Power Dissipation
Functional Description
It is possible to exceed the +125°C maximum junction
temperatures under certain load, power supply conditions and
ambient temperature conditions. It is therefore important to
calculate the maximum junction temperature (TJMAX) for all
applications to determine if power supply voltages, load
conditions, or package type need to be modified to remain in the
safe operating area. These parameters are related using
Equation 1:
The ISL28114, ISL28214 and ISL28414 are single dual and
quad, CMOS rail-to-rail input, output (RRIO) micropower
operational amplifiers. They are designed to operate from single
supply (1.8V to 5.5V) or dual supply (±0.9V to ±2.75V). The parts
have an input common mode range that extends 100mV above
and below the power supply voltage rails. The output stage can
swing to within 15mV of the supply rails with a 10kΩ load.
Input ESD Diode Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. For applications where
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input currents
never exceed 20mA (see Figure 19).
(EQ. 1)
T JMAX = T MAX + θ JA xPD MAXTOTAL
where:
• PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
• PDMAX for each amplifier can be calculated using Equation 2:
V OUTMAX
PD MAX = V S × I qMAX + ( V S - V OUTMAX ) × -----------------------R
(EQ. 2)
L
where:
V+
VIN-
RIN-
-
RIN+
+
RF
• TMAX = Maximum ambient temperature
• θJA = Thermal resistance of the package
• PDMAX = Maximum power dissipation of 1 amplifier
RL
• VS = Total supply voltage
• IqMAX = Maximum quiescent supply current of 1 amplifier
RG
V-
• VOUTMAX = Maximum output voltage swing of the application
• RL = Load resistance
FIGURE 19. INPUT ESD DIODE CURRENT LIMITING
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28114, ISL28214 and ISL28414 are immune to
output phase reversal, even when the input voltage is 1V beyond
the supplies.
Unused Channels
If the application requires less than all amplifiers one channel,
the user must configure the unused channel(s) to prevent it from
oscillating. The unused channel(s) will oscillate if the input and
output pins are floating. This will result in higher than expected
supply currents and possible noise injection into the channel
being used. The proper way to prevent this oscillation is to short
the output to the inverting input and ground the positive input (as
shown in Figure 20).
ISL28114, ISL28214 and ISL28414 SPICE
Model
Figure 21 shows the SPICE model schematic and Figure 22 shows
the net list for the SPICE model. The model is a simplified version
of the actual device and simulates important AC and DC
parameters. AC parameters incorporated into the model are: 1/f
and flatband noise, Slew Rate, CMRR, Gain and Phase. The DC
parameters are IOS, total supply current and output voltage swing.
The model uses typical parameters given in the “Electrical
Specifications” Table beginning on page 4. The AVOL is adjusted
for 90dB with the dominate pole at 125Hz. The CMRR is set 72dB,
f = 80kHz). The input stage models the actual device to present an
accurate AC representation. The model is configured for ambient
temperature of +25°C.
Figures 23 through 30 show the characterization vs simulation
results for the Noise Voltage, Closed Loop Gain vs Frequency,
Large Signal 5V Step Response and CMRR and Open Loop Gain
Phase.
+
FIGURE 20. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
9
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
LICENSE STATEMENT
The information in this SPICE model is protected under the
United States copyright laws. Intersil Corporation hereby grants
users of this macro-model hereto referred to as “Licensee”, a
nonexclusive, nontransferable licence to use this model as long
as the Licensee abides by the terms of this agreement. Before
using this macro-model, the Licensee should read this license. If
the Licensee does not accept these terms, permission to use the
model is not granted.
The Licensee may not sell, loan, rent, or license the macromodel, in whole, in part, or in modified form, to anyone outside
the Licensee’s company. The Licensee may modify the macromodel to suit his/her specific applications, and the Licensee may
make copies of this macro-model for use within their company
only.
This macro-model is provided “AS IS, WHERE IS, AND WITH NO
WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED,
INCLUDING BUY NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.”
In no event will Intersil be liable for special, collateral, incidental,
or consequential damages in connection with or arising out of
the use of this macro-model. Intersil reserves the right to make
changes to the product and the macro-model without prior
notice.
10
FN6800.5
June 23, 2011
DX
.
V1
DX
1e-6
2
R1
1.0004
Vin+
3
En
GAIN = 1
1
R5
4
M15
NCHANNELMOSFET
9 10
IN-
+
-
10
V3
100
16
D2
10
5
6
11
12
IOS1
25e-12
.61
R24
0.425
7
10
Vin-
10
RA2
G2A
13
G2
1
GAIN = 1404
V2
I1
5e-3
Voltage Noise Stage
V4
R8
1
R7
1
R25
18
R12
1
GAIN = 334.753e-3
1e-6
D4
Cin2
1.26e-12
Cin1
1.26e-12
Input Stage
1st Gain Stage
V+
E2
+
-
+
-
GAIN = 1
V++
0
G11
19
GAIN = 24.89e-3
.604
+
-
R13
636.6588k
21
C4
V5
D10
50
D7
DX
V7
24
VOUT
.08
Vc
R19
GAIN = 0.02
10e-12
GAIN = 376.98e-6
R15
10e3
GAIN = 2.5118E-08
Vg
R17
2652.66
+
-
DX
+
-
D9
G7
15.9159E-3
G5
DX
C2
2E-9
+
-
DX
L1
D5
G3
23
26
Vmid
27
ISY
300e-6
D8
.604
E4
.08
+
-
R16
10e3
GAIN = 24.89e-3
C3
2E-9
GAIN = 2.5118E-08
G8
22
10e-12
D11
15.9159E-3
G9
G10
+
-
+
-
GAIN = 0.02
GAIN = 0.02
G12
D12
GAIN = 0.02
V--
V-
Correction Current
E3
FN6800.5
June 23, 2011
+
-
Mid Supply ref V
Gain Stage
C5
L2
Common Mode
2nd Gain Stage
R18
2652.66
GAIN = 376.98e-6
DY
+
-
D6
+
-
DX
G6
DY
R14
636.6588k
+
-
20
V8
25
+
-
Sources
Pole Stage
GAIN = 1
with Zero
0
FIGURE 21. SPICE SCHEMATIC
+
-
+
-
G4
DX
V6
Output Stage
R20
50
ISL28114, ISL28214, ISL28414
Vcm
DX
11
R23
5e11
29
14
R6
17
.61
+
-
CinDif
1.02E-12
0
V9
1
15
EOS
GAIN = 1
0
8
+
-
DN
R22
5e11
D13
R11
GAIN = 334.753e-3
R9
PMOSISIL
M16 PMOSISIL
M17
NCHANNELMOSFET
28
+
-
RA1
+
-
+
-
GAIN = 1404
G1
DX
+
-
R2
1.0004
M14
30
+
-
IN+
En
R21
D3
R10
1e9
D1
G1A
I2
5e-3
ISL28114, ISL28214, ISL28414
*ISL28114 Macromodel - covers following
*products
*ISL28114
*ISL28214
*ISL28414
*
*Revision History:
*Revision B, LaFontaine March 25th 2011
*Model for Noise, quiescent supply currents,
*CMRR 72dB
*fcm=100kHz ,AVOL 90dB f=125Hz SR =
*2.5V/us, GBWP 5MHz, 2nd pole 6Mhz
output *voltage clamp and short ckt current
limit.
*
*Copyright 2011 by Intersil Corporation
*Refer to data sheet "LICENSE
STATEMENT" *Use of this model indicates
your acceptance *with the terms and
provisions in the License *Statement.
*
*Intended use:
*This Pspice Macromodel is intended to give
*typical DC and AC performance
*characteristics under a wide range of
external *circuit configurations using
compatible *simulation platforms - such as
iSim PE.
*
*Device performance features supported by
this *model
*Typical, room temp., nominal power supply
*voltages used to produce the following
*characteristics:
*Open and closed loop I/O impedances
*Open loop gain and phase
*Closed loop bandwidth and frequency
*response
*Loading effects on closed loop frequency
*response
*Input noise terms including 1/f effects
*Slew rate
*Input and Output Headroom limits to I/O
*voltage swing
*Supply current at nominal specified supply
*voltages
*
*Device performance features NOT
supported *by this model
*Harmonic distortion effects
*Disable operation (if any)
*Thermal effects and/or over temperature
*parameter variation
*Limited performance variation vs. supply
*voltage is modeled
*Part to part performance variation due to
*normal process parameter spread
*Any performance difference arising from
*different packaging
* source
* Connections: +input
*
| -input
*
| | +Vsupply
*
| | | -Vsupply
*
| | | | output
*
| | | | |
.subckt ISL28114 Vin+ Vin-V+ V- VOUT
* source ISL28114_DS rev1
*
*Voltage Noise
E_En
VIN+ EN 28 0 1
D_D13
29 28 DN
V_V9
29 0 0.425
R_R21
28 0 30
*
*Input Stage
M_M14
3 1 5 5 NCHANNELMOSFET
M_M15
4 VIN- 6 6 NCHANNELMOSFET
M_M16
11 VIN- 9 9 PMOSISIL
M_M17
12 1 10 10 PMOSISIL
I_I1
7 V-- DC 5e-3
I_I2
V++ 8 DC 5e-3
I_IOS
VIN- 1 DC 25e-12
G_G1A
V++ 14 4 3 1404
G_G2A
V-- 14 11 12 1404
V_V1
V++ 2 1e-6
V_V2
13 V-- 1e-6
R_R1
3 2 1.0004
R_R2
4 2 1.0004
R_R3
5 7 10
R_R4
7 6 10
R_R5
9 8 10
R_R6
8 10 10
R_R7
13 11 1
R_R8
13 12 1
R_RA1
14 V++ 1
R_RA2
V-- 14 1
C_CinDif
VIN- EN 1.02E-12
C_Cin1
V-- EN 1.26e-12
C_Cin2
V-- VIN- 1.26e-12
*
*1st Gain Stage
G_G1
V++ 16 15 VMID 334.753e-3
G_G2
V-- 16 15 VMID 334.753e-3
V_V3
17 16 .61
V_V4
16 18 .61
D_D1
15 VMID DX
D_D2
VMID 15 DX
D_D3
17 V++ DX
D_D4
V-- 18 DX
R_R9
15 14 100
R_R10
15 VMID 1e9
R_R11
16 V++ 1
R_R12
V-- 16 1
*
*2nd Gain Stage
G_G3
V++ VG 16 VMID 24.893e-3
G_G4
V-- VG 16 VMID 24.893e-3
V_V5
19 VG .604
V_V6
VG 20 .604
D_D5
19 V++ DX
D_D6
V-- 20 DX
R_R13
VG V++ 636.658e3
R_R14
V-- VG 636.658e3
C_C2
VG V++ 2E-09
C_C3
V-- VG 2E-09
*
*Mid supply Ref
E_E4
VMID V-- V++ V-- 0.5
E_E2
V++ 0 V+ 0 1
E_E3
V-- 0 V- 0 1
I_ISY
V+ V- DC 300e-6
*
*Common Mode Gain Stage with Zero
G_G5
V++ VC VCM VMID 2.5118E-8
G_G6
V-- VC VCM VMID 2.5118E-8
E_EOS
1 EN VC VMID 1
R_R15
VC 21 10e3
R_R16
22 VC 10e3
R_R22
EN VCM 5e11
R_R23
VCM VIN- 5e11
L_L1
21 V++ 15.9159e-3
L_L2
22 V-- 15.9159e-3
*
*Pole Stage
G_G7
V++ 23 VG VMID 376.98e-6
G_G8
V-- 23 VG VMID 376.98e-6
R_R17
23 V++ 2652.66
R_R18
V-- 23 2652.66
C_C4
23 V++ 10e-12
C_C5
V-- 23 10e-12
*
*Output Stage with Correction Current
Sources
G_G9
26 V-- VOUT 23 0.02
G_G10
27 V-- 23 VOUT 0.02
G_G11
VOUT V++ V++ 23 0.02
G_G12
V-- VOUT 23 V-- 0.02
V_V7
24 VOUT .08
V_V8
VOUT 25 .08
D_D7
23 24 DX
D_D8
25 23 DX
D_D9
V++ 26 DX
D_D10
V++ 27 DX
D_D11
V-- 26 DY
D_D12
V-- 27 DY
R_R19
VOUT V++ 50
R_R20
V-- VOUT 50
.model pmosisil pmos (kp=16e-3 vto=-0.6)
.model NCHANNELMOSFET nmos (kp=3e-3
vto=0.6)
.model DN D(KF=6.69e-9 AF=1)
.MODEL DX D(IS=1E-12 Rs=0.1)
.MODEL DY D(IS=1E-15 BV=50 Rs=1)
.ends ISL28114
FIGURE 22. SPICE NET LIST
12
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Characterization vs Simulation Results
1000
100
10
1
V+ = ±2.5V
AV = 1
INPUT NOISE VOLTAGE (nV/√Hz)
INPUT NOISE VOLTAGE (nV/√Hz)
V+ = ±2.5V
AV = 1
10
100
1k
FREQUENCY (Hz)
10k
1000
100
10
100k
FIGURE 23. CHARACTERIZED INPUT NOISE VOLTAGE
70
GAIN (dB)
AV = 10
0
Rg = 1k, Rf = 100k
0
Rg = OPEN, Rf = 0
100
1k
Rg = 100k, Rf = 100k
-10
10k
100k
1M
FREQUENCY (Hz)
10M
100M
10
100
LARGE SIGNAL (V)
1
VS = ±0.9V
0
RL = 10k
CL = 15pF
AV = +1
VOUT = RAIL
-2
0
1
2
3
4
5
6
TIME (µs)
8
9
FIGURE 27. CHARACTERIZED LARGE SIGNAL TRANSIENT
RESPONSE vs RL, VS = ±0.9V, ±2.5V
13
10
100M
1
VIN
V(VIN+)/VOUT)
-0
-1
RL = 10k
CL = 15pF
AV = +10
VOUT = RAIL
-2
7
10M
VS = ±2.5V
VOUT
2
VS = ±2.5V
-1
10k
100k
1.0M
FREQUENCY (Hz)
(A) AC sims.dat (active)
3
2
1.0k
FIGURE 26. SIMULATED CLOSED LOOP GAIN vs FREQUENCY
3
LARGE SIGNAL (V)
AV = 10
20
Rg = 10k, Rf = 100k
FIGURE 25. CHARACTERIZED CLOSED LOOP GAIN vs FREQUENCY
-3
AV = 100
40
AV = 1
-10
10
100k
Rg = 100, Rf = 100k
AV = 1000
Rg = 10k, Rf = 100k
10
10k
(A) AC sims.dat (active)
60
V+ = ±2.5V
CL = 4pF
RL = 10k
VOUT = 50mVP-P
AV = 100
30
20
100
1k
FREQUENCY (Hz)
Rg = 1k, Rf = 100k
50
40
10
70
Rg = 100, Rf = 100k
AV = 1000
1
FIGURE 24. SIMULATED INPUT NOISE VOLTAGE
GAIN (dB)
60
(A) AC sims.dat (active)
10,000
10,000
-3
0
5
10
15
TIME (µs)
20
25
30
FIGURE 28. SIMULATED LARGE SIGNAL TRANSIENT RESPONSE vs
RL, VS = ±0.9V, ±2.5V
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
20
100
0
80
-20
GAIN
60
-40
40
-60
20
-80
0
-100
-20 V+ = ±0.9V
PHASE
RL = 100k
-40
CL = 10pF
-60 SIMULATION
-80
0.1
1
10 100 1k 10k 100k 1M
FREQUENCY (Hz)
-120
-140
-160
-180
10M 100M
120
80
GAIN
RL = 10k
40
CL = 10pF
MODEL VOS SET TO ZERO
0 FOR THIS TEST
80
70
70
60
60
50
50
1.0
10
100 1.0k 10k 100k 1M 10M 100M
FREQUENCY (Hz)
(A) AC sims.dat (active)
40
30
20
20
10
0.1
FIGURE 30. SIMULATED (SPICE) OPEN-LOOP GAIN, PHASE vs
FREQUENCY
80
30
PHASE
160
0.01
CMRR (dB)
CMRR (dB)
FIGURE 29. SIMULATED (DESIGN) OPEN-LOOP GAIN, PHASE vs
FREQUENCY
40
(A) AC2.dat (active)
200
OPEN LOOP GAIN (dB)/PHASE (°)
120
PHASE (°)
OPEN LOOP GAIN (dB)
Characterization vs Simulation Results (Continued)
10
SIMULATION
0
0.01 0.1
1
10
100 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz)
FIGURE 31. SIMULATED (DESIGN) CMRR
14
0
0.01 0.1
1
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz)
FIGURE 32. SIMULATED (SPICE) CMRR
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to Web to make sure you
have the latest Rev.
DATE
REVISION
CHANGE
5/18/11
FN6800.5
- On page 3, Pin Descriptions: Circuit 3 diagram, removed anti-parallel diodes from the IN+ to INterminals.
- On page 4, Absolute Maximum Ratings: changed Differential Input Voltage from "0.5V" to "V- 0.5V to V+ + 0.5V"
- On page 4, updated CMRR and PSRR parameters in Electrical Specifications table with test
condition specifying -40°C to 125°C typical parameter.
- On page 5, updated Note 7, referenced in MIN and MAX column headings of Electrical
Specifications table, from "Parameters with MIN and/or MAX limits are 100% tested at +25°C,
unless otherwise specified. Temperature limits established by characterization and are not
production tested." to new standard "Compliance to datasheet limits is assured by one or more
methods: production test, characterization and/or design."
- On page 9, under “Input ESD Diode Protection,” removed “They also contain back to-back
diodes across the input terminals.” Removed “Although the amplifier is fully protected, high
input slew rates that exceed the amplifier slew rate (±2.5V/µs) may cause output distortion.”
- On page 9, Figure 19: updated circuit schematic by removing back-to-back input protection
diodes.
- On page 11 replaced SPICE schematic (Figure 21)
- On page 12 replaced SPICE Netlist (Figure 22)
- On page 13 replaced Figure 24
- On page 14 replaced Figure 32
9/23/10
FN6800.4
Added new SC70 pinout package extension as follows:
Added to Related Literature on page 1 “See AN1547 for “ISL28414TSSOPEVAL1Z Evaluation
Board User’s Guide”.
Added to ordering information ISL28114FEV1Z-T7 and ISL28114FEV1Z-T7A and Evaluation
boards.
Added to Pin Configurations new pinout for ISL28114FEV1Z.
Added in Pin Descriptions ISL28114FEV1Z SC70 pin description column.
7/28/10
Changed Note 6 on page page 4 from “For θJC, the “case temp” location is the center of the
exposed metal pad on the package underside.” to
“For θJC, the “case temp” location is taken at the package top center.”
5/13/10
Added “Related Literature” on page 1.
Changed package outline drawing from MDP0038 to P5.064A on page 2 and page 18.
MDP0038 package contained 2 packages for both the 5 and 6 Ld SOT-23. MDP0038 was
obsoleted and the packages were separated and made into 2 separate package outline
drawings; P5.064A and P6.064A. Changes to the 5 Ld SOT-23 were to move dimensions from
table onto drawing, add land pattern and add JEDEC reference number.
Added Note 4 to “Ordering Information” on page 2.
12/16/09
FN6800.3
Removed “Coming Soon” from MSOP package options in the “Ordering Information” on page 2.
Updated the Theta JA for the MSOP package option from 170°C/W to 180°C/W on page 4.
11/17/09
FN6800.2
Removed “Coming Soon” from SC70 and SOT-23 package options in the “Ordering Information”
on page 2.
11/12/09
FN6800.1
Changed theta Ja to 250 from 300. Added license statement (page 10) and reference in spice
model (page 12).
10/23/09
FN6800.0
Initial Release
15
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
*For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page
on intersil.com: ISL28114, ISL28214, ISL28414
To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff
FITs are available from our website at http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Small Outline Transistor Plastic Packages (SC70-5)
P5.049
D
VIEW C
e1
5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
INCHES
5
SYMBOL
4
E
CL
1
2
CL
3
e
E1
b
CL
0.20 (0.008) M
C
C
CL
A
A2
SEATING
PLANE
A1
-C-
PLATING
b1
0.043
0.80
1.10
-
0.004
0.00
0.10
-
A2
0.031
0.039
0.80
1.00
-
b
0.006
0.012
0.15
0.30
-
b1
0.006
0.010
0.15
0.25
c
0.003
0.009
0.08
0.22
6
c1
0.003
0.009
0.08
0.20
6
D
0.073
0.085
1.85
2.15
3
E
0.071
0.094
1.80
2.40
-
E1
0.045
0.053
1.15
1.35
3
e
0.0256 Ref
0.65 Ref
-
e1
0.0512 Ref
1.30 Ref
-
L2
c1
NOTES
0.031
0.010
0.018
0.017 Ref.
0.26
0.46
4
0.420 Ref.
0.006 BSC
0o
N
c
MAX
0.000
α
WITH
MIN
A
L
b
MILLIMETERS
MAX
A1
L1
0.10 (0.004) C
MIN
-
0.15 BSC
8o
0o
5
8o
-
5
5
R
0.004
-
0.10
-
R1
0.004
0.010
0.15
0.25
Rev. 3 7/07
NOTES:
BASE METAL
1. Dimensioning and tolerances per ASME Y14.5M-1994.
2. Package conforms to EIAJ SC70 and JEDEC MO-203AA.
4X θ1
3. Dimensions D and E1 are exclusive of mold flash, protrusions,
or gate burrs.
R1
4. Footlength L measured at reference to gauge plane.
5. “N” is the number of terminal positions.
R
GAUGE PLANE
SEATING
PLANE
L
C
L1
α
L2
6. These Dimensions apply to the flat section of the lead between
0.08mm and 0.15mm from the lead tip.
7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only.
4X θ1
VIEW C
0.4mm
0.75mm
2.1mm
0.65mm
TYPICAL RECOMMENDED LAND PATTERN
17
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Package Outline Drawing
P5.064A
5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
Rev 0, 2/10
1.90
0-3°
D
A
0.08-0.20
5
4
PIN 1
INDEX AREA
2.80
3
1.60
3
0.15 C D
2x
2
5
(0.60)
0.20 C
2x
0.95
SEE DETAIL X
B
0.40 ±0.05
3
END VIEW
0.20 M C A-B D
TOP VIEW
10° TYP
(2 PLCS)
2.90
5
H
0.15 C A-B
2x
C
1.45 MAX
1.14 ±0.15
0.10 C
SIDE VIEW
SEATING PLANE
(0.25) GAUGE
PLANE
0.45±0.1
0.05-0.15
4
DETAIL "X"
(0.60)
(1.20)
NOTES:
(2.40)
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to ASME Y14.5M-1994.
3.
Dimension is exclusive of mold flash, protrusions or gate burrs.
4.
Foot length is measured at reference to guage plane.
5.
This dimension is measured at Datum “H”.
6.
Package conforms to JEDEC MO-178AA.
(0.95)
(1.90)
TYPICAL RECOMMENDED LAND PATTERN
18
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Package Outline Drawing
M8.118A
8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP)
Rev 0, 9/09
3.0±0.1
8
A
0.25
CAB
3.0±0.1
4.9±0.15
DETAIL "X"
1.10 Max
PIN# 1 ID
B
SIDE VIEW 2
1
0.18 ± 0.05
2
0.65 BSC
TOP VIEW
0.95 BSC
0.86±0.09
H
GAUGE
PLANE
C
0.25
SEATING PLANE
0.33 +0.07/ -0.08
0.08 C A B
0.10 ± 0.05
3°±3°
0.10 C
0.55 ± 0.15
DETAIL "X"
SIDE VIEW 1
5.80
NOTES:
4.40
3.00
1.
Dimensions are in millimeters.
2.
Dimensioning and tolerancing conform to JEDEC MO-187-AA
and AMSE Y14.5m-1994.
3.
Plastic or metal protrusions of 0.15mm max per side are not
included.
4.
Plastic interlead protrusions of 0.25mm max per side are not
included.
5.
Dimensions “D” and “E1” are measured at Datum Plane “H”.
6.
This replaces existing drawing # MDP0043 MSOP 8L.
0.65
0.40
1.40
TYPICAL RECOMMENDED LAND PATTERN
19
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Package Outline Drawing
M8.15E
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 0, 08/09
4
4.90 ± 0.10
A
DETAIL "A"
0.22 ± 0.03
B
6.0 ± 0.20
3.90 ± 0.10
4
PIN NO.1
ID MARK
5
(0.35) x 45°
4° ± 4°
0.43 ± 0.076
1.27
0.25 M C A B
SIDE VIEW “B”
TOP VIEW
1.75 MAX
1.45 ± 0.1
0.25
GAUGE PLANE
C
SEATING PLANE
0.10 C
0.175 ± 0.075
SIDE VIEW “A
0.63 ±0.23
DETAIL "A"
(0.60)
(1.27)
NOTES:
(1.50)
(5.40)
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
5.
The pin #1 identifier may be either a mold or mark feature.
6.
Reference to JEDEC MS-012.
TYPICAL RECOMMENDED LAND PATTERN
20
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SYMBOL
SO-14
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
±0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
±0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
±0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
±0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
±0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
±0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
±0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
±0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
-
N
SO-8
SO16
(0.150”)
8
14
16
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
21
FN6800.5
June 23, 2011
ISL28114, ISL28214, ISL28414
Thin Shrink Small Outline Package Family (TSSOP)
MDP0044
0.25 M C A B
D
THIN SHRINK SMALL OUTLINE PACKAGE FAMILY
A
MILLIMETERS
(N/2)+1
N
SYMBOL 14 LD 16 LD 20 LD 24 LD 28 LD TOLERANCE
PIN #1 I.D.
E
E1
1
(N/2)
B
0.20 C B A
2X
N/2 LEAD TIPS
TOP VIEW
0.05
e
C
SEATING
PLANE
H
A
1.20
1.20
1.20
1.20
1.20
Max
A1
0.10
0.10
0.10
0.10
0.10
±0.05
A2
0.90
0.90
0.90
0.90
0.90
±0.05
b
0.25
0.25
0.25
0.25
0.25
+0.05/-0.06
c
0.15
0.15
0.15
0.15
0.15
+0.05/-0.06
D
5.00
5.00
6.50
7.80
9.70
±0.10
E
6.40
6.40
6.40
6.40
6.40
Basic
E1
4.40
4.40
4.40
4.40
4.40
±0.10
e
0.65
0.65
0.65
0.65
0.65
Basic
L
0.60
0.60
0.60
0.60
0.60
±0.15
L1
1.00
1.00
1.00
1.00
1.00
Reference
Rev. F 2/07
0.10 M C A B
b
0.10 C
N LEADS
NOTES:
1. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusions or gate burrs shall not exceed
0.15mm per side.
SIDE VIEW
2. Dimension “E1” does not include interlead flash or protrusions.
Interlead flash and protrusions shall not exceed 0.25mm per
side.
SEE DETAIL “X”
3. Dimensions “D” and “E1” are measured at dAtum Plane H.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
c
END VIEW
L1
A
A2
GAUGE
PLANE
0.25
L
A1
0° - 8°
DETAIL X
22
FN6800.5
June 23, 2011