Intersil ISL6131IRZA-T Multiple voltage supervisory ic Datasheet

ISL6131, ISL6132
®
Data Sheet
August 17, 2010
Multiple Voltage Supervisory ICs
Features
The ISL6131 and ISL6132 are a family of high accuracy
multi voltage supervisory ICs designed to monitor voltages
greater than 0.7V in applications ranging from
microprocessors to industrial power systems. The ISL6131
is an undervoltage four supply supervisor whereas the
ISL6132 is a two voltage supervisor monitoring both for
undervoltage (UV) and overvoltage (OV) conditions.
• Operates from 1.5V to 5.5V Supply Voltage
Both ICs feature four external resistor programmable voltage
monitoring (VMON) inputs each with a related STATUS
output that individually reports the related monitor input
condition. In addition there is a PGOOD (power good) signal
that asserts high when the STATUS outputs are in their
correct state. There is a stability delay of approximately
160ms to ensure that the monitored supply is stable before
STATUS and PGOOD are released to go high. The PGOOD
and STATUS outputs are open-drain to allow ORing of the
signals and interfacing to a wide range of logic levels.
STATUS and PGOOD outputs are guaranteed to be valid
with IC bias lower than 1V eliminating concern about
STATUS and PGOOD outputs during IC bias up and down.
VMON inputs are designed to ignore momentary transients
on the monitored supplies.
• Four Adjustable Voltage Monitoring Thresholds
• 150ms STATUS/PGOOD Stability Time Delay
• Four Individual Open Drain STATUS Outputs
• Guaranteed STATUS/PGOOD Valid to VDD <1V
• VDD and VMON Glitch Immunity
• VDD Lock Out
• 4mm X 4mm QFN Package
• QFN Package:
- Compliant to JEDEC PUB95 MO-220
QFN - Quad Flat No Leads - Package Outline
- Near Chip Scale Package footprint, which improves
PCB efficiency and has a thinner profile
• Pb-Free (RoHS Compliant)
Applications
• Multivoltage DSPs and Processors
• µP Voltage Monitoring
• Embedded Control Systems
• Graphics Cards
Ordering Information
PART
NUMBER
FN9119.4
• Intelligent Instruments
TEMP.
RANGE
PART
(°C)
MARKING
PACKAGE
PKG.
DWG. #
• Medical Equipment
• Network Routers
ISL6131IRZA*
(Note)
61 31IRZ
-40 to +85 24 Ld 4x4 QFN L24.4x4
(Pb-free)
• Portable Battery-Powered Equipment
ISL6132IRZA*
(Note)
61 32IRZ
-40 to +85 24 Ld 4x4 QFN L24.4x4
(Pb-free)
• Telecommunications Systems
• Set-Top Boxes
ISL613XSUPEREVAL2 Evaluation Platform
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel
specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special
Pb-free material sets, molding compounds/die attach materials, and
100% matte tin plate plus anneal (e3 termination finish, which is RoHS
compliant and compatible with both SnPb and Pb-free soldering
operations). Intersil Pb-free products are MSL classified at Pb-free peak
reflow temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003, 2004, 2005, 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
VDD
VMON_A
GROUND
VMON_B
VDD
VMON_D
UVMON_2
GROUND
FIGURE 1. ISL6131 TYPICAL APPLICATION USAGE
2
V1 IN
V2 IN
Rm
OVMON_1
OVMON_2
PGOOD1
PGOOD2
EN
Ru
UVMON_1
VMON_C
PGOOD
OVSTATUS_2
UVSTATUS_2
OVSTATUS_1
UVSTATUS_1
A IN
B IN
C IN
D IN
STATUS A
STATUS B
STATUS C
STATUS D
ISL6131, ISL6132
Rl
EN1 EN2
FIGURE 2. ISL6132 TYPICAL APPLICATION USAGE
FN9119.4
August 17, 2010
ISL6131, ISL6132
Pinout
ISL6131, ISL6132 (24 LD QFN)
TOP VIEW
24
23
22
21
20
19
1
18
2
17
3
16
PD
4
15
5
14
6
13
7
8
9
10
11
12
Pin Descriptions
PIN
6131
6132
PIN NAME
23
23
VDD
Bias IC from nominal 1.5V to 5V
10
10
GND
IC ground
20
NA
VMON_A
12
NA
VMON_B
17
NA
VMON_C
14
NA
VMON_D
NA
12
OVMON_1
NA
20
UVMON_1
FUNCTION DESCRIPTION
On the ISL6131 these inputs provide for a programmable UV threshold referenced to an internal 0.633V. The
related STATUS output will assert once the related input > internal reference voltage.
On the ISL6132, these inputs provide for a programmable UV and OV threshold referenced to an internal 0.633V
reference. In the ‘AB’ pair VMON_A is the UV input and VMON_B is the OV input. In the ‘CD’ pair VMON_C is
the UV input and VMON_D is the OV input.
These inputs have a 30μs glitch filter to prevent PGOOD reset due to a transient.
NA
17
UVMON_2
NA
14
OVMON_2
24
24
PGOOD
On the ISL6131, PGOOD is the boolean AND function of all four STATUS outputs.
On the ISL6132, PGOOD is for the AB pair and signals high when the monitored voltage is within the specified
window and the A and B STATUS output states are correct.
This is an open drain output and is to be pulled high to the appropriate level with an external resistor to a VDD
maximum level.
NA
9
PGOOD2
PGOOD2 is for the CD pair and signals high when the monitored voltage is within the specified window and when
the C and D STATUS output states are correct.
This is an open drain output and is to be pulled high to the appropriate level with an external resistor to a VDD
maximum level.
2
NA
STATUS_A
5
NA
STATUS_B
6
NA
STATUS_C
On the ISL6131 each STATUS provides a high signal through pull-up resistors about 160ms after its related
VMON has continuously been > Vuv_vth. This delay is for stabilization of monitored voltages. STATUS will deassert and pull low upon VMON not being satisfied for about 30μs.
7
NA
STATUS_D
NA
5
OVSTATUS_1
NA
2
UVSTATUS_1
NA
6
UVSTATUS_2
NA
7
OVSTATUS_2
1
1
EN1
On ISL6131 provides 4 voltage UV function enabling/disabling input. Internally pulled up to VDD.
Controls monitor 1 (AB pair) on ISL6132.
NA
11
EN2
On ISL6132, controls monitor 2 (CD pair) voltage, voltage monitoring function enabling input, pulled up to VDD.
-
PD
Thermal Pad. Should be electrically connected to GND.
NC
3, 4, 8, 13, 15, 16, 18,
19, 21, 22
On the ISL6132 the STATUS outputs indicate compliance with a high output state for each pair of monitors.
No Connect
3
FN9119.4
August 17, 2010
ISL6131, ISL6132
Absolute Maximum Ratings
Thermal Information
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6.0V
VMON, ENABLE, STATUS, PGOOD . . . . . . . . . . -0.3V to VDD+0.3V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2kV (HBM)
Thermal Resistance (Typical, Notes 1, 2)
θJA (°C/W)
θJC (°C/W)
4x4 QFN Package . . . . . . . . . . . . . . . .
48
9
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
VDD Supply Voltage Range . . . . . . . . . . . . . . . . . . . . +1.5V to +5.5V
Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
3. All voltages are relative to GND, unless otherwise specified.
Electrical Specifications
Nominal VDD = 1.5V to +5V, TA = TJ = -40°C - 85°C, Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 4)
TYP
MAX
(Note 4)
UNIT
619
633
647
mV
-
40
-
nV/°C
VMON/ENABLE INPUTS
VMON Threshold
VVMONvth
TJ = +25°C
TJ from -40°C to +85°C
VMON Threshold Temp. Coeff.
TCVMONvth
VMON Hysteresis
VVMONhys
-
10
-
mV
VMON Glitch Filter
Tfil
-
30
-
μs
VMON Minimum Input Impedance
Zin_min
Tj = +40°C, VMON within 63mV of
VVMONvth
8
MΩ
ENABLE L2H, Delay to STATUS & PGOOD
VMON valid, EN high to STATUS & PG high
-
160
-
ms
EN H2L, Delay to PGOOD
EN low to PGOOD low
-
-
0.1
μs
EN H2L, Delay to STATUS
EN low to STATUS low
-
13
-
μs
ENABLE Pull-up Voltage
EN open
-
VDD
-
V
-
VDD/2
-
V
ENABLE Threshold Voltage
VENVTH
STATUS/PGOOD OUTPUTS
STATUS Pull-Down Current
IRSTpd
RST = 0.1V
-
88
-
mA
STATUS/PGOOD Delay after VMON Valid
TdelST
VMON > VUVvth to STATUS = 0.2V
-
160
-
ms
Measured at VDD = 1.0V
-
0.04
0.1
V
STATUS/PGOOD Output Low
Vol
BIAS
IC Supply Current
IVDD_5.5V
VDD = 5V
-
170
-
μA
IC Supply Current
IVDD_3.3V
VDD = 3.3V
-
145
-
μA
IC Supply Current
IVDD_1.5V
VDD = 1.5V
-
100
-
μA
VDD Power On
VDD_POR
VDD high to low
-
0.89
1
V
VDD_LO
VDD low to high
-
0.91
-
V
VDD Power On Lock Out
NOTE:
4. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
4
FN9119.4
August 17, 2010
ISL6131, ISL6132
Description and Operation
The ISL6131 is a four voltage high accuracy supervisory IC
designed to monitor multiple voltages greater than 0.7V
relative to PIN 10 of the IC.
Upon VDD bias power up, the STATUS and PGOOD outputs
are held correctly low once VDD is as low as 1V. Once
biased to 1.5V the IC continuously monitors from one to four
voltages independently through external resistor dividers
comparing each voltage monitoring (VMON) pin voltage to
an internal 0.633V (VVMONvth) reference.
With the EN input driven high or open as each VMON input
rises above VVMONvth a timer is set to ensure ~160ms of
continuous compliance then the related STATUS output is
released to be pulled high. The STATUS outputs are opendrain to allow ORing of these signals and interfacing to a
logic high level up to VDD. The STATUS are designed to
reject short transients (~30μs) on the VMON inputs. Once all
STATUS outputs are high a power good (PGOOD) output
signal is generated high to indicate all the monitored
voltages are greater than minimum compliance level.
Once any VMON input falls below VVMONvth for longer than
the glitch filter time both the PGOOD and the related STATUS
output are pulled low. The other STATUS outputs will remain
high as long as their corresponding VMON voltage remains
valid and the PGOOD validation process is reset.
Figure 1 illustrates ISL6131 typical application schematic and
Figure 3 is an operational timing diagram. See Figures 10 to
17 for ISL6131 function and performance. Figures 10 and 11
show the VDD rising along with STATUS and PGOOD
response. Figures 12 and 13 illustrate VMON falling below
VVMONvth and Figure 14 illustrates VMON rising above
VVMONvth with STATUS and PGOOD response. Figure 15
shows the VDD failing with STATUS and PGOOD response.
Figures 16 and 17 illustrate ENABLE to STATUS and PGOOD
timing.
If less than four voltages are being monitored, connect the
unused VMON pins to VDD for proper operation. All unused
STATUS outputs can be left open.
The ISL6132 is a dual voltage monitor for under and
overvoltage compliance. Figure 2 illustrates the typical
ISL6132 implementation schematic and Figure 4 is the
operational timing diagram.
There are 2 pairs of monitors each with an undervoltage
(UVMON) input and overvoltage (OVMON) input along with
with associated STATUS and PGOOD outputs.
Upon VDD bias power up, the STATUS and PGOOD outputs
are held correctly low once VDD is as low as 1V. Once
biased to 1.5V the IC continuously monitors the voltage
through external resistor dividers comparing each VMON pin
voltage to an internal 0.633V reference. At proper bias the
OVSTATUS are pulled high and the UVSTATUS and
5
PGOOD are pulled low. Once the UVMON input > the
VMON Vth continuously for ~160ms, its associated STATUS
output will release high indicating that the minimum voltage
condition has been met. As both UVMON and OVMON
inputs are satisfied the PGOOD output is released to go high
indicating that the monitored voltage is within the specified
window. Figure 18 illustrates this performance for a 4V to 5V
window.
When VMON does not satisfy its voltage high or low criteria
for more than the glitch filter time, the associated STATUS
and PGOOD are pulled low. Figures 19 and 20 illustrate this
performance for a 4V to 5V compliant window.
Figures 21-23 illustrate the VMON glitch filter timing to
STATUS and PGOOD notification and transient immunity.
The ENABLE input when pulled low allows for monitoring
and reporting function to be disabled. Figure 24 shows
ENABLE high to PGOOD timing for compliant voltage.
When choosing resistors for the divider remember to keep
the current through the string bounded by power loss
tolerance at the top end and noise immunity at the bottom
end. For most applications total divider resistance in the
10kΩ -100kΩ range is advisable with 1% tolerance resistors
being used to reduce monitoring error.
Referencing Figures 1 and 2, choosing the two resistor
values is straightforward for the ISL6131 as the ratio of
resistance should equal the ratio of the desired trip voltage
to the internal reference, 0.633V).
For the ISL6131, two dividers of two resistors each can be
employed to monitor the OV and UV levels for each voltage.
Otherwise, use a single three resistor string for each voltage.
In the three resistor divider string the ratio of the desired
over voltage trip point to the internal reference is equal to the
ratio of the two upper resistors to the lowest (GND
connected) resistor. The desired under voltage trip point
ratio to the internal reference voltage is equal to the ratio of
the uppermost (voltage connected) resistor to the lower two
resistors. An example follows;
1. Establish lower and upper trip level: 3.3V ±20% or 2.64V
(UV) and 3.96V (OV)
2. Establish total resistor string value: 10kΩ, Ir = divider current
3. (Rm+Rl)*Ir = 0.623V @ UV and Rl * Ir = 0.633V @ OV
4. Rm+Rl = 0.623V / Ir @ UV => Rm+Rl = 0.623V / (2.64V
/10kΩ) = 2.359kΩ
5. Rl = 0.633V / Ir @ OV => Rl = 0.633V /(3.96V/10kΩ) =
1.598kΩ
6. Rm = 2.359kΩ - 1.598kΩ = 0.761kΩ
7. Ru = 10kΩ - 2.397kΩ = 7.641kΩ
8. Choose standard value resistors that most closely
approximate these ideal values. Choosing a different total
divider resistance value may yield a more ideal ratio with
available resistors values.
FN9119.4
August 17, 2010
ISL6131, ISL6132
VMONVth
A
B
VMON
INPUT
VOLTAGE
C
D
C
D
STSDLY
STSDLY
<Tfil
>Tfil
STSDLY
STSDLY
STSDLY
A
STATUS OUTPUTS
B
C
C
D
PGOOD OUTPUT
EN INPUT
FIGURE 3. ISL6131 OPERATIONAL DIAGRAM
OVERVOLTAGE
LIMIT
OV
TdelST
Tfil
UNDERVOLTAGE
LIMIT
<Tfil
TdelST
Tfil
MONITORED VOLTAGE
RAMPING UP & DOWN
OVSTATUS
UVSTATUS
PGOOD OUTPUT
FIGURE 4. ISL6132 OPERATIONAL DIAGRAM
Typical Performance Curves
634
0.30
0.25
VDD = 5V
632
VB BIAS CURRENT (mA)
UV THRESHOLD (mV)
633
631
630
VDD = 1.5V
629
628
0.15
0.1
0.05
627
626
-40
0.20
-20
0
20
40
60
TEMPERATURE (°C)
FIGURE 5. UV THRESHOLD
6
80
100
-40
-20
0
20
40
60
80
100
TEMPERATURE (°C)
FIGURE 6. VDD CURRENT
FN9119.4
August 17, 2010
ISL6131, ISL6132
Applications Usage
Using the ISL613XSUPEREVAL2 Platform
on. Additional ISL6131s can be employed in parallel to
sequence any number of DC-DC convertors is in this
fashion.
The ISL613XSUPEREVAL2 platform is the primary
evaluation board for this family of supervisors and is
designed to support the ISL6131, ISL6132. In addition, it
also supports the ISL6125 sequencer as it has open drain
RESET# outputs similar to the STATUS outputs of the
ISL6131 and ISL6132.
VIN
EN
VIN
The ISL613XSUPEREVAL2 is shipped with a ISL6125
soldered into the SMD channel 2 position and with 2 each of
the ISL6131 (1 socketed) and ISL6132 loose packed. The
four resistor divider strings are set so that VMON = VMON
Vth (0.633V) once supplies are 2.10V on the IN_D, 1.27V on
IN_C, 4.27V on IN_B and 2.78V on IN_A. On the ISL6131
these are the 4 UV levels at ~85% of 2.5V, 1.5V, 5V and
3.3V respectively.
LEDs turned off are the PGOOD high indicators with D4
being the ISL6131 indicator.
With VDD ranging from 1.5V to 5V or shorted to IN_A
through JP1 and with an ISL6131 in the socket, PGOOD will
release to be pulled high once those minimum conditions are
met. See Figures 10 to 17 for performance and function
examples.
With the ISL6132 in the socket and IN_C and IN_D tied to a
common supply and IN_A and IN_B tied to a second supply
the ISL6132 will look for a voltage between 1.27V to 2.10V
on the CD pair and between 2.78V and 4.27V for the AB
pair. Once either supply meets its requirement the related
PGOOD will release to pull high and turn off the related LED.
See Figures 18 to 24 for performance and function
examples. Figures 25 and 26 illustrate the
ISL613XSUPEREVAL2 platform in image and schematic.
Using the ISL6131, ISL6132 for Negative Voltage
Monitoring Applications
The ISL6131, ISL6132 can be used for -V monitoring as it
monitors any voltage more positive relative to its GND pin.
With correct bias differential these parts can monitor any
voltage regardless of polarity or amplitude.
Using the ISL6131 for ‘Loss Less’ Sequencing
Applications
The ISL6131 can be used in a ‘loss less’ sequencing
application where a monitored output voltage determines the
start of the next sequenced turn-on. As shown in Figure 7,
VMON_A input looks at the common VIn of several DC-DC
converters and enables DC-DC_A with STATUS _A, once
both VIn and ENABLE are satisfied. VMON_B monitors the
output of DC-DC_A and when the acceptable output voltage
is reached, DC-DC_B is enabled with STATUS_B output.
This sequencing pattern is continued until all DC-DC outputs
are on, at which time PGOOD signal will be released to
indicate. 160ms delay from VMON > VVMONVth to STATUS
high ensures stability at each step prior to subsequent turn7
EN
VIN
EN
ABC
STATUS
PGOOD
VOUT
DC-DC_A
VOUT
DC-DC_B
VOUT
DC-DC_C
VMON_A
VMON_D
ISL6131 VMON_C
VDD
ENABLE
VMON_B
GND
FIGURE 7. ISL6131 ‘LOSSLESS’ SEQUENCING
CONFIGURATION
Using the ISL6131 for System Voltage and Over
Temperature Monitoring
Being a multivoltage monitoring IC the ISL6131 can also be
used to monitor over temperature as well as voltage for a
more complete coverage of system health. Using a Negative
Temperature Coefficient (NTC) passive device in place of
one of the resistors in a VMON divider provides over
temperature monitoring either locally or remotely.
Evaluations of this application configuration have involved
the QT0805T-202J, QT0805Y-502J and QT0805Y-103J
NTCs from Quality Thermistor.
ISL6131 over temperature monitoring is not as accurate as
specific temperature monitor ICs but this implementation
provides a cost efficient solution with 5% tolerances
achievable.
See Figures 8 - 9 for over temp sensing configuration and
operation results. In this example, the desired maximum
temp is 100°C. The QT0805Y-103J NTC was placed at the
end of 3 feet of twisted pair wire to emulate a remote sensing
application. From the Quality Thermistor data sheet, this
NTC device has a +25°C value of 10K and at +100°C a
value of 0.923K. An accompanying standard value resistor
of 3.83K was chosen for divider so that at 100°C, VMON
~0.633V with the bias voltage at 3.3V.
FN9119.4
August 17, 2010
ISL6131, ISL6132
The resulting falling VMON trip point with configuration
shown is ~0.634V, with ~0.642V for rising which equates to
~95°C for under temperature and ~97°C for over
temperature respectively. Choosing the standard resistor
value above and below R1 allows for small adjustments in
the temperature trip point.
The low ISL6131 VMON temperature coefficient makes this
a viable and low cost addition to complete system
monitoring.
TEMP INDICATOR
TEMP (°C)
VMON (V)
TEMP STATUS
25
2.36
H = Under Temp
50
1.61
H = Under Temp
75
1.01
H = Under Temp
95
0.67
H = Under Temp
100
0.61
L = Over Temp
105
0.54
L = Over Temp
STATUS
3.3V
VMON 0.1V/DIV
VDD
3.83k
R1
VMON
T
ISL6131
QT0805Y-103J
(REMOTE HEAT
SOURCE LOCATION)
Low = OVER TEMP
GND
TEMP STATUS 5V/DIV
FIGURE 8. ISL6131 OVER TEMP SENSING CONFIGURATION
10s/DIV
FIGURE 9. ISL6132 OVER TEMP SENSING RESULT
Functional and Performance Waveforms
STATUS OUTPUTS PULLED-UP TO 1.5V
VDD RISING
STATUS OUTPUTS TO VDD
VDD RISING
PGOOD
PGOOD
1V/DIV
100μs/DIV
FIGURE 10. ISL6131 VDD RISING
8
1V/DIV
200μs/DIV
FIGURE 11. ISL6131 VDD RISING WITH PULL-UP
FN9119.4
August 17, 2010
ISL6131, ISL6132
Functional and Performance Waveforms (Continued)
VMON FALLING BELOW UV Vth (0.1V/DIV)
UV Vth 0.63V
VMON FALLING BELOW UV Vth (0.1V/DIV)
UV Vth 0.63V
UNRELATED STATUS OUTPUTS
UNRELATED STATUS OUTPUTS
RELATED STATUS OUTPUT
RELATED STATUS OUTPUT
PGOOD
PGOOD
1V/DIV
40ms/DIV
FIGURE 12. ISL6131 VMON FALLING TO PGOOD
1V/DIV
10ms/DIV
FIGURE 13. ISL6131 VMON FALLING TO PGOOD
VMON RISING ABOVE UV Vth (0.1V/DIV)
UV Vth 0.63V
VDD FALLING
UNRELATED STATUS OUTPUTS
STATUS OUTPUTS
RELATED STATUS OUTPUT
PGOOD
PGOOD
1V/DIV
20ms/DIV
1V/DIV
FIGURE 14. ISL6131 UV RISING TO PGOOD
40ms/DIV
FIGURE 15. ISL6131 VDD FALLING
ENABLE
STATUS
ENABLE
STATUS
PGOOD
PGOOD
2V/DIV
20ms/DIV
FIGURE 16. ISL6131 ENABLE L2H TO PGOOD
9
2V/DIV
2µs/DIV
FIGURE 17. ISL6131 EN H2L TO PGOOD
FN9119.4
August 17, 2010
ISL6131, ISL6132
Functional and Performance Waveforms (Continued)
MONITORING 4V TO 5V
MONITORING 4V TO 5V
OV STATUS
VDD RISING
MONITORED VOLTAGE FALLING
OV STATUS RISING
UV/PGOOD
STATUS RISING
1V/DIV
40ms/DIV
PGOOD AND UV
STATUS PULLED LOW
1V/DIV
FIGURE 18. ISL6132 TURN-ON
10ms/DIV
FIGURE 19. ISL6132 IN UV CONDITION
MONITORING 4V TO 5V
MONITORING 4V TO 5V
UV STATUS
VMON FALLING (1V/DIV)
MONITORED VOLTAGE RISING
4V MIN LIMIT
UV STATUS
PGOOD AND OV
STATUS PULLED LOW
OV STATUS
PGOOD
1V/DIV
10ms/DIV
FIGURE 20. ISL6132 IN OV CONDITION
5V/DIV
10µs/DIV
FIGURE 21. ISL6132 UV GLITCH FILTER TIMING
MONITORING 4V TO 5V
VMON RISING (1V/DIV)
5V MAX LIMIT
VMON 5.5V TO 3.5V
UV STATUS
UV, OV STATUS & PGOOD
OV STATUS
5VOUT
PGOOD
5V/DIV
10µs/DIV
FIGURE 22. ISL6132 OV GLITCH FILTER TIMING
10
8µs/DIV
FIGURE 23. ISL6132 GLITCH FILTER TRANSIENT IMMUNITY
FN9119.4
August 17, 2010
ISL6131, ISL6132
Functional and Performance Waveforms (Continued)
ENABLE
PGOOD
OV, UV STATUS
1V/DIV
20ms/DIV
FIGURE 24. ISL6132 ENABLE TO PGOOD
FIGURE 25. ISL613XSUPEREVAL2 PHOTOGRAPH
11
FN9119.4
August 17, 2010
ISL6131, ISL6132
VDD
IN2
JP1
R16
R15
IN4
IN3
R17
R18
IN1
1
R1
R3
R5
R7
2
3
STATUS
4
VDD
C1
VMON2 (OV1)
R9
VMON4 (OV2)
R2
VMON3 (UV2)
R4
VMON1 (UV1)
R6
ISL6131,
ISL6132
R8
D4
R10
D3
PGOOD1
PGOOD2
GND
EN1
EN2
FIGURE 26. ISL613XSUPEREVAL2 CHANNEL 1 SCHEMATIC
TABLE 1. ISL6131SUPEREVAL2 BOARD CHANNEL 1 COMPONENT LISTING
COMPONENT
DESIGNATOR
COMPONENT FUNCTION
COMPONENT DESCRIPTION
DUT1
ISL6131, Quad Under Voltage Supervisor in socket
Intersil, ISL6131IR Quad Under Voltage Supervisor
DUT2
ISL6132, Dual Over & Under Voltage Supervisor in bag
Intersil, ISL6132IR Dual Over & Under Voltage Supervisor
R1A
IN2 to VMONB (OV1) Resistor for Divider String
8.45kΩ 1%, 0402
R2A
VMONB (OV1) to GND Resistor for Divider String
1.47kΩ 1%, 0402
R7A
IN1 to VMONA (UV1) Resistor for Divider String
7.68kΩ 1%, 0402
R8A
VMONA (UV1) to GND Resistor for Divider String
2.26kΩ 1%, 0402
R3A
IN4 to VMOND (OV2) Resistor for Divider String
6.98kΩ 1%, 0402
R4A
VMOND (OV2) to GND Resistor for Divider String
3.01kΩ 1%, 0402
R5A
IN3 to VMONC (UV2) Resistor for Divider String
4.99kΩ 1%, 0402
R6A
VMONC (UV2) to GND Resistor for Divider String
4.99kΩ 1%, 0402
STATUS Pull-up Resistors
5.1kΩ 10%, 0402
C1A
Decoupling Capacitor
0.1μF, 0805
D3, D4
PGOOD# INDICATOR
SMD RED LED
R15-R18
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
12
FN9119.4
August 17, 2010
ISL6131, ISL6132
Package Outline Drawing
L24.4x4
24 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 4, 10/06
4.00
4X 2.5
A
20X 0.50
B
PIN 1
INDEX AREA
PIN #1 CORNER
(C 0 . 25)
24
19
1
18
4.00
2 . 10 ± 0 . 15
13
0.15
(4X)
12
7
0.10 M C A B
0 . 07
24X 0 . 23 +- 0
. 05 4
24X 0 . 4 ± 0 . 1
TOP VIEW
BOTTOM VIEW
SEE DETAIL "X"
0.10 C
C
0 . 90 ± 0 . 1
BASE PLANE
( 3 . 8 TYP )
SEATING PLANE
0.08 C
SIDE VIEW
(
2 . 10 )
( 20X 0 . 5 )
C
0 . 2 REF
5
( 24X 0 . 25 )
0 . 00 MIN.
0 . 05 MAX.
( 24X 0 . 6 )
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 indentifier may be
either a mold or mark feature.
13
FN9119.4
August 17, 2010
Similar pages