Intersil ISL80102IR18Z High performance 2a and 3a linear regulator Datasheet

High Performance 2A and 3A Linear Regulators
ISL80102, ISL80103
Features
The ISL80102 and ISL80103 are low voltage, high-current, single
output LDOs specified for 2A and 3A output current, respectively.
These LDOs operate from the input voltages of 2.2V to 6V and
are capable of providing the output voltages of 0.8V to 5V on the
adjustable VOUT versions. Fixed output voltage options are
available in 1.8V, 2.5V, 3.3V and 5V. Other custom voltage
options available upon request.
• Stable with all capacitor types (Note 10)
• 2A and 3A output current ratings
• 2.2V to 6V input voltage range
• ±1.8% VOUT accuracy guaranteed over line, load and
TJ = -40°C to +125°C
• Very low 120mV dropout voltage at 3A (ISL80103)
For applications that demand in-rush current less than the
current limit, an external capacitor on the soft-start pin provides
adjustment. The ENABLE feature allows the part to be placed into
a low quiescent current shutdown mode. A sub-micron BiCMOS
process is utilized for this product family to deliver the best in
class analog performance and overall value.
• Fixed and adjustable VOUT versions
• Very fast transient response
• Excellent 62dB PSRR
• 100µVRMS output noise
These CMOS (LDOs) will consume significantly lower quiescent
current as a function of load over bipolar LDOs, which translates
into higher efficiency and the ability to consider packages with
smaller footprints. The quiescent current has been modestly
compromised to enable a leading class fast load transient
response, and hence a lower total AC regulation band for an LDO
in this category.
• Power-good output
• Adjustable in-rush current limiting
• Short circuit and over-temperature protection
• Available in a 10 Ld DFN
• Servers
• Telecommunications and networking
• Medical equipment
• Instrumentation systems
• Routers and switchers
ISL80102, ISL80103
1.8V ±1.8%
2.5V ±10%
9
VIN
CIN
10
10µF
1
VIN
VOUT
VIN
VOUT
2
VOUT
COUT
10µF
RPG
ON
7
OFF
6
*CSS
SENSE
ENABLE
3
4
SS
PG
100kΩ
PGOOD
GND
5
*CSS is optional, (see Note 11) on page 5.
FIGURE 1. TYPICAL APPLICATION
June 14, 2013
FN6660.6
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2009-2012, 2013. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL80102, ISL80103
Block Diagram
VIN
R5
10µA
10µA
IL/10,000
M4
M5
M3
M1
POWER PMOS
IL
VOUT
+
R8
R7
R9
EN
EN
+
R2
R4
EN
ADJ
+
500mV
V TO I
M8
SENSE
500mV
M7
SS
R1
-
EN
ENABLE
LEVEL
SHIFT
M6
-
M2
+
485mV
EN
PG
-
+
+
-
*R3
GND
*R3 is open for ADJ versions.
Ordering Information
PART NUMBER
(Notes 1, 2, 3)
PART
MARKING
VOUT
VOLTAGE
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG
DWG. #
ISL80102IRAJZ
DZJA
ADJ
-40 to +125
10 Ld 3x3 DFN
L10.3x3
ISL80102IR18Z
DZNA
1.8V
-40 to +125
10 Ld 3x3 DFN
L10.3x3
ISL80102IR25Z
DZPA
2.5V
-40 to +125
10 Ld 3x3 DFN
L10.3x3
ISL80103IRAJZ
DZAA
ADJ
-40 to +125
10 Ld 3x3 DFN
L10.3x3
ISL80103IR18Z
DZEA
1.8V
-40 to +125
10 Ld 3x3 DFN
L10.3x3
ISL80103IR25Z
DZFA
2.5V
-40 to +125
10 Ld 3x3 DFN
L10.3x3
ISL80102EVAL2Z
Evaluation Board
ISL80103EVAL2Z
Evaluation Board
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL80102, ISL80103. For more information on MSL please see tech brief
TB363.
2
FN6660.6
June 14, 2013
ISL80102, ISL80103
Pin Configuration
ISL80102, ISL80103
(10 LD 3x3 DFN)
TOP VIEW
VOUT
1
10 VIN
VOUT
2
9 VIN
SENSE/ADJ
3
8 DNC
PG
4
7 ENABLE
GND
5
6 SS
Pin Descriptions
PIN NUMBER
PIN NAME
DESCRIPTION
1, 2
VOUT
3
SENSE/ADJ
4
PG
5
GND
6
SS
7
ENABLE
8
DNC
Do not connect this pin to ground or supply. Leave floating.
9, 10
VIN
Input supply pin.
Output voltage pin.
Remote voltage sense for internally fixed VOUT options. ADJ pin for externally set VOUT.
VOUT in regulation signal. Logic low defines when VOUT is not in regulation. Must be grounded if not used.
GND pin.
External cap adjusts in-rush current.
VIN independent chip enable. TTL and CMOS compatible.
EPAD
EPAD must be connected to copper plane with as many vias as possible for proper electrical and optimal thermal
performance.
Typical Application
ISL80102, ISL80103
2.5V ±10%
VIN
9
CIN
10
10µF
1.8V
VOUT
VIN
VOUT
VIN
1
2
VOUT
COUT
10µF
RPG
100kΩ
R1
10kΩ
7
EN
OPEN DRAIN COMPATIBLE
6
*CSS
PG
4
PGOOD
ENABLE
**CPB
SS
GND
ADJ
3
5
1500pF
R3
2.61kΩ
R4
1.0kΩ
*CSS is optional, (see Note 11) on page 5.
**CPB is optional. See “Functional Description” on page 12 for more information.
FIGURE 2. TYPICAL APPLICATION DIAGRAM
3
FN6660.6
June 14, 2013
ISL80102, ISL80103
Absolute Maximum Ratings (Note 6)
Thermal Information
VIN Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
VOUT Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
PG, ENABLE, SENSE/ADJ, SS, Relative to GND. . . . . . . . . . . -0.3V to +6.5V
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
10 Ld 3x3 DFN Package (Notes 4, 5). . . . .
45
4
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+150°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions (Note 8)
Junction Temperature Range (TJ) . . . . . . . . . . . . . . . . . . .-40°C to +125°C
VIN Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2V to 6V
VOUT Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800mV to 5V
PG, ENABLE, SENSE/ADJ, SS Relative to GND . . . . . . . . . . . . . . . . 0V to 6V
PG Sink Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
6. ABS max voltage rating is defined as the voltage applied for a lifetime average duty cycle above 6V of 1%.
7. Electromigration specification defined as lifetime average junction temperature of +110°C where max rated DC current = lifetime average current.
Electrical Specifications Unless otherwise noted, all parameters are established over the following specified conditions:
VIN = VOUT + 0.4V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, ILOAD = 0A. Applications must follow thermal guidelines of the package to
determine worst case junction temperature. Please refer to “Functional Description” on page 12 and Tech Brief TB379.
Boldface limits apply over the operating temperature range, -40°C to +125°C. Pulse load techniques used by ATE to ensure TJ = TA defines
established limits.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 8)
TYP
MAX
(Note 8)
UNITS
DC CHARACTERISTICS
DC Output Voltage Accuracy
VOUT
VOUT Options: 1.8V.
VIN =2.2V; ILOAD = 0A
VOUT Options: 1.8V.
2.2V < VIN < 3.6V; 0A < ILOAD < 3A
0.5
-1.8
VOUT Options: 2.5V
VIN =VOUT + 0.4V; ILOAD = 0A
Feedback Pin (ADJ Version)
VFB
DC Input Line Regulation
ΔVOUT/ΔVIN
ΔVOUT/ΔIOUT
DC Output Load Regulation
Ground Pin Current
Ground Pin Current in Shutdown
1.8
0.5
VOUT Options: 2.5V
VOUT + 0.4V < VIN < 6V; 0A < ILOAD < 3A
-1.8
2.2V < VIN < 6V, 0A < ILOAD < 3A
491
%
%
-1.8
%
500
509
mV
VOUT + 0.4V < VIN < 3.6V, VOUT = 1.8V
0.1
0.4
%
VOUT + 0.4V < VIN < 6V, VOUT = 2.5V
0.1
0.8
%
0A < ILOAD < 3A, All voltage options
-0.8
%
0A < ILOAD < 2A, All voltage options
-0.6
%
VADJ = 0.5V
Feedback Input Current
%
0.01
1
µA
IQ
ILOAD = 0A, 2.2V < VIN < 6V
7.5
9
mA
ILOAD = 3A, 2.2V < VIN < 6V
8.5
12
mA
ISHDN
ENABLE Pin = 0.2V, VIN = 5V
0.4
ENABLE Pin = 0.2V, VIN = 6V
3.3
16
µA
120
185
mV
125
mV
µA
Dropout Voltage (Note 9)
VDO
ILOAD = 3A, VOUT = 2.5V, 10 LD 3x3 DFN
ILOAD = 2A, VOUT = 2.5V, 10 LD 3x3 DFN
81
Output Short Circuit Current
(3A Version)
ISC
VOUT = 0V, VOUT + 0.4V < VIN < 6V
5.0
A
VOUT = 0V, VOUT + 0.4V < VIN < 6V
2.8
A
Output Short Circuit Current
(2A Version)
4
FN6660.6
June 14, 2013
ISL80102, ISL80103
Electrical Specifications Unless otherwise noted, all parameters are established over the following specified conditions:
VIN = VOUT + 0.4V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, ILOAD = 0A. Applications must follow thermal guidelines of the package to
determine worst case junction temperature. Please refer to “Functional Description” on page 12 and Tech Brief TB379.
Boldface limits apply over the operating temperature range, -40°C to +125°C. Pulse load techniques used by ATE to ensure TJ = TA defines
established limits. (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 8)
TYP
MAX
(Note 8)
UNITS
Thermal Shutdown Temperature
TSD
VOUT + 0.4V < VIN < 6V
160
°C
Thermal Shutdown Hysteresis
(Rising Threshold)
TSDn
VOUT + 0.4V < VIN < 6V
15
°C
AC CHARACTERISTICS
Input Supply Ripple Rejection
PSRR
Output Noise Voltage
f = 1kHz, ILOAD = 1A; VIN = 2.2V
55
dB
f = 120Hz, ILOAD = 1A; VIN = 2.2V
62
dB
ILOAD = 10mA, BW = 300Hz < f < 300kHz
100
µVRMS
ENABLE PIN CHARACTERISTICS
Turn-on Threshold
VEN(HIGH)
2.2V < VIN < 6V
0.616
0.8
Turn-off Threshold
VEN(LOW)
2.2V < VIN < 6V
0.463
0.6
V
Hysteresis
VEN(HYS)
2.2V < VIN < 6V
135
mV
COUT = 10µF, ILOAD = 1A
150
µs
Enable Pin Turn-on Delay
tEN
0.95
VIN = 6V, EN = 3V
Enable Pin Leakage Current
1
V
µA
SOFT-START CHARACTERISTICS
Reset Pull-Down resistance
RPD
Soft-Start Charge Current
ICHG
Ω
323
-7
-4.5
-2
µA
75
84
92
%VOUT
PG PIN CHARACTERISTICS
VOUT PG Flag Threshold
VOUT PG Flag Hysteresis
4
PG Flag Low Voltage
ISINK = 500µA
PG Flag Leakage Current
VIN = 6V, PG = 6V
%
47
100
mV
0.05
1
µA
NOTES:
8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
9. Dropout is defined by the difference in supply VIN and VOUT when the supply produces a 2% drop in VOUT from its nominal value.
10. Minimum cap of 10µF X5R/X7R on VIN and VOUT required for stability.
11. If the current limit for in-rush current is acceptable in application, do not use this feature. Used only when large bulk capacitance required on VOUT for
application.
5
FN6660.6
June 14, 2013
ISL80102, ISL80103
Typical Operating Performance
Unless otherwise noted: VIN = 2.2V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, IL = 0A.
2.0
1.8
1.8
OUTPUT VOLTAGE (V)
ΔVOUT (%)
1.2
0.6
0
-0.6
-1.2
1.6
+125°C
1.4
1.2
+25°C
1.0
-40°C
0.8
0.6
0.4
0.2
-1.8
-50
-25
0
25
50
75
100
JUNCTION TEMPERATURE (°C)
125
0
150
FIGURE 3. ΔVOUT vs TEMPERATURE
0
1
3
2
4
SUPPLY VOLTAGE (V)
5
6
FIGURE 4. OUTPUT VOLTAGE vs SUPPLY VOLTAGE
9
1.8
8
0.6
GROUND CURRENT (mA)
ΔVOUT (%)
1.2
+25°C
0.0
-0.6
-40°C
-1.2
-1.8
+125°C
0
0.5
1.0
1.5
2.0
2.5
7
6
5
4
3
2
1
0
3.0
3
2
OUTPUT CURRENT (A)
9.1
12.0
8.9
11.5
11.0
8.7
-40°C
8.5
8.3
+25°C
8.1
+125°C
7.9
-40°C
10.5
10.0
9.5
+125°C
9.0
+25°C
8.0
0.5
6
8.5
7.7
7.5
0
5
FIGURE 6. GROUND CURRENT vs SUPPLY VOLTAGE
CURRENT (mA)
GROUND CURRENT (mA)
FIGURE 5. ΔVOUT vs OUTPUT CURRENT
4
INPUT VOLTAGE (V)
1.0
1.5
2.0
OUTPUT CURRENT (A)
2.5
FIGURE 7. GROUND CURRENT vs OUTPUT CURRENT
6
3.0
7.5
0.8
1.4
2.0
2.6
3.2
3.8
OUTPUT VOLTAGE (V)
4.4
5.0
FIGURE 8. GROUND CURRENT vs OUTPUT VOLTAGE
FN6660.6
June 14, 2013
ISL80102, ISL80103
Typical Operating Performance
5.0
12
4.5
11
10
9
8
7
6
5
4
3
4.0
GROUND CURRENT (µA)
GROUND CURRENT (µA)
Unless otherwise noted: VIN = 2.2V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, IL = 0A. (Continued)
3.5
3.0
2.5
2.0
1.5
1.0
VIN = 5V
0.5
0.0
-40 -25 -10
5
20 35 50 65 80
TEMPERATURE (°C)
95 110 125
150
140
130
120
110
2A
100
90
3A
80
70
60
50
40
30
20
1A
10
0
-40 -25 -10
5 20 35 50 65 80
TEMPERATURE (°C)
95
110 125
FIGURE 11. DROPOUT VOLTAGE vs TEMPERATURE
VIN = 6V
5
20 35 50 65 80
TEMPERATURE (°C)
95 110 125
FIGURE 10. SHUTDOWN CURRENT vs TEMPERATURE
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
FIGURE 9. SHUTDOWN CURRENT vs TEMPERATURE
2
1
0
-40 -25 -10
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
0
0.5
1.0
1.5
2.0
OUTPUT CURRENT (A)
2.5
3.0
FIGURE 12. DROPOUT VOLTAGE vs OUTPUT CURRENT
0.90
0.85
0.80
VOLTAGE (V)
0.75
VIN (1V/DIV)
0.70
0.65
SS (1V/DIV)
0.60
0.55
0.50
0.45
VOUT (1V/DIV)
0.40
0.35
0.30
-40 -25 -10
5 20 35 50 65 80 95 110 125
JUNCTION TEMPERATURE (°C)
FIGURE 13. ENABLE THRESHOLD VOLTAGE vs TEMPERATURE
7
PG (1V/DIV)
TIME (10ms/DIV)
FIGURE 14. POWER-UP (VIN = 2.2V)
FN6660.6
June 14, 2013
ISL80102, ISL80103
Typical Operating Performance
Unless otherwise noted: VIN = 2.2V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, IL = 0A. (Continued)
EN (1V/DIV)
VIN (1V/DIV)
SS (1V/DIV)
SS (1V/DIV)
VOUT (1V/DIV)
VOUT (1V/DIV)
PG (1V/DIV)
PG (1V/DIV)
TIME (10ms/DIV)
TIME (50µs/DIV)
FIGURE 15. POWER-DOWN (VIN = 2.2V)
FIGURE 16. ENABLE START-UP
300
SS (1V/DIV)
VOUT (1V/DIV)
250
START-UP TIME (µs)
EN (1V/DIV)
300
CURRENT LIMIT (A)
START-UP TIME (µs)
250
50
0
-40 -25 -10
5 20 35 50 65 80 95 110 125
JUNCTION TEMPERATURE (°C)
FIGURE 19. START-UP TIME vs TEMPERATURE
8
2.5
3.0
3.5
4.0
4.5
5.0
INPUT VOLTAGE (V)
5.5
6.0
FIGURE 18. START-UP TIME vs SUPPLY VOLTAGE
FIGURE 17. ENABLE SHUTDOWN
100
100
0
2.0
TIME (5ms/DIV)
150
150
50
PG (1V/DIV)
200
200
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
-40 -25 -10
ISL80103
ISL80102
5
20
35
50
65
80
95 110 125
JUNCTION TEMPERATURE (°C)
FIGURE 20. CURRENT LIMIT vs TEMPERATURE
FN6660.6
June 14, 2013
ISL80102, ISL80103
Typical Operating Performance
CURRENT LIMIT (A)
Unless otherwise noted: VIN = 2.2V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, IL = 0A. (Continued)
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
2.0
ISL80103
VOUT (1V/DIV)
ISL80102
2.5
3.0
3.5
4.0
4.5
INPUT VOLTAGE (V)
5.0
5.5
FIGURE 21. CURRENT LIMIT vs SUPPLY VOLTAGE
6.0
IOUT (1A/DIV)
TIME (10ms/DIV)
FIGURE 22. CURRENT LIMIT RESPONSE (ISL80102)
VOUT (1V/DIV)
VOUT (1V/DIV)
IOUT (1A/DIV)
IOUT (2A/DIV)
TIME (100ms/DIV)
FIGURE 23. THERMAL CYCLING (ISL80102)
TIME (20ms/DIV)
FIGURE 24. CURRENT LIMIT RESPONSE (ISL80103)
EN (1V/DIV)
VOUT (1V/DIV)
IOUT (2A/DIV)
IOUT (2A/DIV)
VOUT (1V/DIV)
TIME (50ms/DIV)
FIGURE 25. THERMAL CYCLING (ISL80103)
9
TIME (1ms/DIV)
FIGURE 26. IN-RUSH CURRENT WITH NO SOFT-START
CAPACITOR, COUT = 1000µF
FN6660.6
June 14, 2013
ISL80102, ISL80103
Typical Operating Performance
Unless otherwise noted: VIN = 2.2V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, IL = 0A. (Continued)
EN (1V/DIV)
EN (1V/DIV)
IOUT (2A/DIV)
IOUT (2A/DIV)
VOUT (1V/DIV)
VOUT (1V/DIV)
TIME (1ms/DIV)
FIGURE 27. IN-RUSH WITH 22nF SOFT-START CAPACITOR,
COUT = 1000µF
VOUT (50mV/DIV)
IOUT (2A/DIV)
TIME (1ms/DIV)
FIGURE 28. IN-RUSH WITH 47nF SOFT-START CAPACITOR,
COUT = 1000µF
VOUT (50mV/DIV)
IOUT (2A/DIV)
di/dt = 30A/µs
di/dt = 30A/µs
TIME (200µs/DIV)
FIGURE 29. LOAD TRANSIENT 0A TO 3A, COUT = 10µF CERAMIC
VOUT (50mV/DIV)
IOUT (2A/DIV)
di/dt = 30A/µs
TIME (200µs/DIV)
FIGURE 30. LOAD TRANSIENT 0A TO 3A, COUT = 10µF CERAMIC
+ 100µF OSCON
VOUT (50mV/DIV)
IOUT (2A/DIV)
di/dt = 30A/µs
TIME (200µs/DIV)
TIME (200µs/DIV)
FIGURE 31. LOAD TRANSIENT 1A TO 3A, C OUT = 10µF CERAMIC
10
FIGURE 32. LOAD TRANSIENT 1A TO 3A, COUT = 10µF CERAMIC
+ 100µF OSCON
FN6660.6
June 14, 2013
ISL80102, ISL80103
Typical Operating Performance
Unless otherwise noted: VIN = 2.2V, VOUT = 1.8V, CIN = COUT = 10µF, TJ = +25°C, IL = 0A. (Continued)
VOUT (20mV/DIV)
VOUT (20mV/DIV)
di/dt = 3A/μsec
IOUT (2A/DIV)
IOUT (2A/DIV)
di/dt = 3A/µs
di/dt = 3A/µs
TIME (50µs/DIV)
TIME (50µs/DIV)
FIGURE 33. LOAD TRANSIENT 0A TO 3A, COUT = 10µF CERAMIC,
NO CPB (ADJ VERSION)
FIGURE 34. LOAD TRANSIENT 0A TO 3A, COUT = 10µF CERAMIC,
CPB = 1500pF (ADJ VERSION)
80
3.2V
70
2.2V
60
VIN (1V/DIV)
dB
50
1A
40
30
100mA
20
VOUT (10mV/DIV)
10
0
10
TIME (200µs/DIV)
FIGURE 35. LINE TRANSIENT
100
1k
10k
FREQUENCY (Hz)
100k
1M
FIGURE 36. PSRR vs LOAD
80
10
70
100µF
NOISE µV/√Hz
60
dB
50
40
30
1
0.1
20
10
0
10µF
IL = 100mA
10
100
1k
10k
FREQUENCY (Hz)
FIGURE 37. PSRR vs COUT
11
47µF
100k
1M
0.01
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
FIGURE 38. SPECTRAL NOISE DENSITY vs FREQUENCY
FN6660.6
June 14, 2013
ISL80102, ISL80103
Functional Description
Despite other output voltages offered, this family of LDOs is
optimized for a true 2.5V to 1.8V conversion where the input
supply can have a tolerance of as much as ±10% for conditions
noted in the “Electrical Specifications” table on page 4. Minimum
guaranteed input voltage is 2.2V, however, due to the nature of
an LDO, VIN must be some margin higher than the output voltage
plus dropout at the maximum rated current of the application if
active filtering (PSRR) is expected from VIN to VOUT. The dropout
spec of this family of LDOs has been generously specified in
order to allow applications to design for a level of efficiency that
can accommodate the smaller outline package.
IN-RUSH CURRENT LIMIT (A)
Input Voltage Requirements
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0
20
40
60
CSS (nF)
80
100
FIGURE 39. IN-RUSH CURRENT vs SOFT-START CAPACITANCE
Enable Operation
The Enable turn-on threshold is typically 770mV with a hysteresis of
135mV. An internal pull-up or pull-down resistor is available upon
request. As a result, this pin must not be left floating. This pin must
be tied to VIN if it is not used. A 1kΩ to 10kΩ pull-up resistor is
required for applications that use open collector or open drain
outputs to control the Enable pin. The Enable pin may be connected
directly to VIN for applications that are always on.
Power-Good Operation
Applications not using this feature must connect this pin to
ground. The PGOOD flag is an open-drain NMOS that can sink up
to 10mA during a fault condition. The PGOOD pin requires an
external pull-up resistor, which is typically connected to the VOUT
pin. The PGOOD pin should not be pulled up to a voltage source
greater than VIN. The PGOOD fault can be caused by the output
voltage going below 84% of the nominal output voltage, or the
current limit fault, or low input voltage. The PGOOD does not
function during thermal shutdown. While the PGOOD functions in
shutdown.
Soft-Start Operation (Optional)
If the current limit for in-rush current is acceptable in the
application, do not use this feature. The soft-start circuit controls
the rate at which the output voltage comes up to regulation at
power-up or LDO enable. A constant current charges an external
soft-start capacitor. The external capacitor always gets
discharged to ground pin potential at the beginning of start-up or
enabling. The discharge rate is the RC time constant of RPD and
CSS. See Figures 26 through 29 in the “Typical Operating
Performance Curves” beginning on page 6. RPD is the
ON-resistance of the pull down MOSFET, M8. RPD is 300Ω
typically.
The soft-start feature effectively reduces the in-rush current at
power-up or LDO enable until VOUT reaches regulation. The
in-rush current can be an issue for applications that require large,
external bulk capacitances on VOUT where high levels of charging
current can be seen for a significant period of time. The in-rush
currents can cause VIN to drop below minimum which could
cause VOUT to shutdown. Figure 39 shows the relationship
between in-rush current and CSS with a COUT of 1000µF.
12
Output Voltage Selection
An external resistor divider is used to scale the output voltage
relative to the internal reference voltage. This voltage is then fed
back to the error amplifier. The output voltage can be
programmed to any level between 0.8V and 5V. An external
resistor divider, R3 and R4, is used to set the output voltage as
shown in Equation 1. The recommended value for R4 is 500Ω to
1kΩ. R3 is then chosen according to Equation 2:
⎛ R3
⎞
V OUT = 0.5V × ⎜ ------- + 1⎟
⎝ R4
⎠
(EQ. 1)
V OUT
R 3 = R 4 × ⎛ ------------- – 1⎞
⎝ 0.5V
⎠
(EQ. 2)
External Capacitor Requirements
External capacitors are required for proper operation. To ensure
optimal performance careful attention must be paid to the layout
guidelines and selection of capacitor type and value.
OUTPUT CAPACITOR
The ISL80102, ISL80103 applies state-of-the-art internal
compensation to keep selection of the output capacitor simple
for the customer. Stable operation over full temperature, VIN
range, VOUT range and load extremes are guaranteed for all
capacitor types and values assuming a 10µF X5R/X7R is used
for local bypass on VOUT. This minimum capacitor must be
connected to VOUT and Ground pins of the LDO with PCB traces
no longer than 0.5cm.
Lower cost Y5V and Z5U type ceramic capacitors are acceptable
if the size of the capacitor is larger to compensate for the
significantly lower tolerance over X5R/X7R types. Additional
capacitors of any value in Ceramic, POSCAP or Alum/Tantalum
Electrolytic types may be placed in parallel to improve PSRR at
higher frequencies and/or load transient AC output voltage
tolerances.
INPUT CAPACITOR
The minimum input capacitor required for proper operation is
10µF having a ceramic dielectric. This minimum capacitor must
be connected to VIN and ground pins of the LDO with PCB traces
no longer than 0.5cm.
FN6660.6
June 14, 2013
ISL80102, ISL80103
Phase Boost Capacitor (Optional)
The ISL80102 and ISL80103 are designed to be stable with
10µF or larger ceramic capacitor.
Applications using the ADJ versions, may see improved
performance with the addition of a small ceramic capacitor CPB
as shown in Figure 2 on page 3. The conditions where CPB may
be beneficial are: (1) VOUT > 1.5V, (2) COUT = 10µF, and (3) tight
AC voltage regulation band.
CPB introduces phase lead with the product of R3 and CPB that
results in increasing the bandwidth of the LDO. Typical R3 x CPB
should be 4μs.
CPB not recommended for VOUT < 1.5V.
The maximum allowable junction temperature, TJ(MAX) and the
maximum expected ambient temperature, TA(MAX) will determine the
maximum allowable power dissipation as shown in Equation 4:
(EQ. 4)
P D ( MAX ) = ( T J ( MAX ) – T A ) ⁄ θ JA
Where θJA is the junction-to-ambient thermal resistance.
For safe operation, please make sure that power dissipation
calculated in Equation 3, PD be less than the maximum
allowable power dissipation PD(MAX).
The DFN package uses the copper area on the PCB as a heatsink.
The EPAD of this package must be soldered to the copper plane
(GND plane) for heat sinking. Figure 40 shows a curve for the θJA
of the DFN package for different copper area sizes.
Current Limit Protection
46
44
42
θJA, C/W
The ISL80102, ISL80103 family of LDOs incorporates protection
against overcurrent due to short, overload condition applied to
the output and the in-rush current that occurs at start-up. The
LDO performs as a constant current source when the output
current exceeds the current limit threshold noted in the
“Electrical Specifications” table on page 4. If the short or
overload condition is removed from VOUT, then the output returns
to normal voltage mode regulation. In the event of an overload
condition, the LDO might begin to cycle on and off due to the die
temperature exceeding the thermal fault condition. The
TO220/TO263 package will tolerate higher levels of power
dissipation on the die which may never thermal cycle if the
heatsink of this larger package can keep the die temperature
below the specified typical thermal shutdown temperature.
40
38
36
34
2
4
6
8
10
12
14
16
18
20
2
EPAD-MOUNT COPPER LAND AREA ON PCB, mm
22
24
FIGURE 40. 3mmx3mm-10 PIN DFN ON 4-LAYER PCB WITH
THERMAL VIAS θJA vs EPAD-MOUNT COPPER LAND
AREA ON PCB
Power Dissipation and Thermals
Thermal Fault Protection
The junction temperature must not exceed the range specified in
the “Recommended Operating Conditions (Note 8)” on page 4.
The power dissipation can be calculated by using Equation 3:
In the event the die temperature exceeds typically +160°C, then
the output of the LDO will shut down until the die temperature
can cool down to typically +145°C. The level of power combined
with the thermal impedance of the package (+48°C/W for DFN)
will determine if the junction temperature exceeds the thermal
shutdown temperature.
P D = ( V IN – V OUT ) × I OUT + V IN × I GND
13
(EQ. 3)
FN6660.6
June 14, 2013
ISL80102, ISL80103
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest Rev.
DATE
REVISION
CHANGE
May 23, 2013
FN6660.6
Pin Descriptions on page page 3, updated EPAD section From: EPAD at ground potential. Soldering it directly to
GND plane is optional. To: EPAD must be connected to copper plane with as many vias as possible for proper
electrical and optimal thermal performance.
Removed obsolete part numbers: ISL80102IR33Z, ISL80102IR50Z, ISL80103IR33Z, ISL80103IR50Z from
ordering information table on page 2.
Added evaluation boards to ordering information table on page 2: ISL80103IR50Z and ISL80103EVAL2Z.
Features on page 1: Removed 5 Ld TO220 and 5 Ld TO263.
Input Voltage Requirements on page 12: Removed the sentence “those applications that cannot accommodate
the profile of the TO220/TO263”.
June 14, 2012
FN6660.5
In “Thermal Information” on page 4, corrected θJA from 48 to 45.
February 14, 2012
FN6660.4
Increased “VEN(HIGH)” minimum limit from 0.4V to 0.616 and added the “VEN(LOW)” spec for clarity on page 5.
December 14, 2011
FN6660.3
Increased “Turn-on Threshold” minimum limit on page 5 from 0.3V to 0.4V.
Updated “Package Outline Drawing” on page 16 as follows:
Removed package outline and included center to center distance between lands on recommended land pattern.
Removed Note 4 "Dimension b applies to the metallized terminal and is measured between 0.18mm and 0.30mm
from the terminal tip." since it is not applicable to this package. Renumbered notes accordingly.
March 4, 2011
FN6660.2
Converted to new template
On page 1 - first paragraph, changed "Fixed output voltage options are available in 1.5V, 1.8V, 2.5V, 3.3V and 5V"
to "Fixed output voltage options are available in 1.8V, 2.5V, 3.3V and 5V"
In “Ordering Information” table on page 2, removed ISL80102IR15Z and ISL80103IR15Z.
In Note 3 on page 2, below the “Ordering Information” table , removed '1.5V', so it reads “The 3.3V and 5V fixed
output voltages will be released in the future. Please contact Intersil Marketing for more details.”
March 4, 2010
FN6660.1
Corrected Features on page 1 as follows:
-Changed bullet "• 185mV Dropout @ 3A, 125mV Dropout @ 2A" to "• Very Low 120mV Dropout at 3A"
-Changed bullet "• 65dB Typical PSRR" to "• 62dB Typical PSRR"
-Deleted 0.5% Initial VOUT Accuracy
Modified Figure 1 and placed as “TYPICAL APPLICATION” on page 1.
Moved Pinout to page 3
In “Block Diagram” on page 2, corrected resistor associated with M5 from R4 to R5
Updated “Block Diagram” on page 2 as follows”
- Added M8 from SS to ground.
Updated Figure 1 on page 1 as follows:
-Corrected Pin 6 from SS to IRSET
-Removed Note 11 callout "Minimum cap on VIN and VOUT required for stability." Added Note "*CSS is optional.
See Note 12 on Page 5." and “** CPB is optional. See “Functional Description” on page 12 for more information.”
Added "The 1.5V, 3.3V and 5V fixed output voltages will be released in the future." to Note 3 on page 2.
In “Thermal Information” on page 4, updated Theta JA from 45 to 48.
In “Soft-Start Operation (Optional)” on page 12:
-Changed "The external capacitor always gets discharged to 0V at start-up of after coming out of a chip disable.
"The external capacitor always gets discharged to ground pin potential at start-up or enabling."
-Changed "The soft-start function effectively limits the amount of in-rush current below the programmed current
limit during start-up or an enable sequence to avoid an overcurrent fault condition." to "The soft-start feature
effectively reduces the in-rush current at power-up or LDO enable until VOUT reaches regulation."
-Added "See Figures 25 through 27 in the “Typical Operating Performance Curves” beginning on page 6."
-Added “RPD is the on resistance of the pull-down MOSFET, M8. RPD is 300Ω typically.”
14
FN6660.6
June 14, 2013
ISL80102, ISL80103
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest Rev. (Continued)
DATE
March 4, 2010
REVISION
CHANGE
FN6660.1 Added “Phase Boost Capacitor (Optional)” on page 13.
(CONTINUED) In “Typical Operating Performance” on page 11, revised figure "PSRR vs VIN" which had 3 curves with “SPECTRAL
NOISE DENSITY vs FREQUENCY” which has one curve.
Added "Figure 33. “LOAD TRANSIENT 0A TO 3A, COUT = 10µF CERAMIC, NO CPB (ADJ VERSION)” and "Figure 34.
“LOAD TRANSIENT 0A TO 3A, COUT = 10µF CERAMIC, CPB = 1500pF (ADJ VERSION)”
September 30, 2009
FN6660.0
Initial Release.
About Intersil
Intersil Corporation is a leader in the design and manufacture of high-performance analog, mixed-signal and power management
semiconductors. The company's products address some of the largest markets within the industrial and infrastructure, personal
computing and high-end consumer markets. For more information about Intersil, visit our website at www.intersil.com.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting
www.intersil.com/en/support/ask-an-expert.html. Reliability reports are also available from our website at
http://www.intersil.com/en/support/qualandreliability.html#reliability
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
15
FN6660.6
June 14, 2013
ISL80102, ISL80103
Package Outline Drawing
L10.3x3
10 LEAD DUAL FLAT PACKAGE (DFN)
Rev 7, 10/11
3.00
5
PIN #1 INDEX AREA
A
B
1
5
PIN 1
INDEX AREA
(4X)
3.00
2.00
8x 0.50
2
10 x 0.23
0.10
1.60
TOP VIEW
10x 0.35
BOTTOM VIEW
(4X)
0.10 M C A B
0.415
0.200
0.23
0.35
(10 x 0.55)
SEE DETAIL "X"
(10x 0.23)
1.00
MAX
0.10 C
BASE PLANE
2.00
0.20
C
SEATING PLANE
0.08 C
SIDE VIEW
(8x 0.50)
C
0.20 REF
4
1.60
0.05
2.85 TYP
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Tiebar shown (if present) is a non-functional feature.
5.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
16
FN6660.6
June 14, 2013
Similar pages