Microsemi JANTXV1N4622UR-1 Leadless package for surface mount Datasheet

• 1N4614UR-1 THRU 1N4627UR-1 AVAILABLE IN JAN,
JANTX, JANTXV AND
1N4614UR-1
thru
JANS
PER MIL-PRF-19500/435
1N4627UR-1
and
• LEADLESS PACKAGE FOR SURFACE MOUNT
• LOW CURRENT OPERATION AT 250 µA
CDLL4614 thru CDLL4627
• METALLURGICALLY BONDED
MAXIMUM RATINGS
Operating Temperatures: -65°C to +175°C
DC Power Dissipation: 500mW @ TEC = +125°C
Power Derating: 10 mW / °C above TEC = +125°C
Forward Voltage @ 200 mA: 1.1 Volts maximum
ELECTRICAL CHARACTERISTICS @ 25°C, unless otherwise speci½ed.
CDI
TYPE
NUMBER
NOMINAL
ZENER
VOLTAGE
V @I
Z
ZT
ZENER
TEST
CURRENT
I
ZT
(Note 1)
MAXIMUM
ZENER
IMPEDANCE
Z
@I
ZT
ZT
MAXIMUM REVERSE
LEAKAGE CURRENT
1
R
MAXIMUM
DC ZENER
CURRENT
@V
R
(Note 2)
DIM
D
F
G
G1
S
MILLIMETERS
INCHES
MIN MAX MIN MAX
1.60
1.70 0.063 0.067
0.41
0.55 0.016 0.022
3.30
3.70 .130 .146
2.54 REF.
.100 REF.
0.03 MIN.
.001 MIN.
VOLTS
µ A
OHMS
µ A
VOLTS
mA
CDLL4614
CDLL4615
1.8
2.0
250
250
1200
1250
7.5
5.0
1
1
120
110
CDLL4616
CDLL4617
2.2
2.4
250
250
1300
1400
4.0
2.0
1
1
100
95
CDLL4618
CDLL4619
2.7
3.0
250
250
1500
1600
1.0
0.8
1
1
90
87
CDLL4620
CDLL4621
3.3
3.6
250
250
1650
1700
7.5
7.5
1.5
2
85
83
CDLL4622
CDLL4623
3.9
4.3
250
250
1650
1600
5.0
4.0
2
2
80
77
CDLL4624
CDLL4625
4.7
5.1
250
250
1550
1500
10.0
10.0
3
3
75
70
LEAD FINISH: Tin / Lead
CDLL4626
CDLL4627
5.6
6.2
250
250
1400
1200
10.0
10.0
4
5
65
61
THERMAL RESISTANCE: (ROJEC):
100 °C/W maximum at L = 0 inch
NOTE 1
NOTE 2
The CDI type numbers shown above have a Zener voltage tolerance of +5.0%.
Nominal Zener voltage is measured with the device junction in thermal
equilibrium at an ambient temperature of 25°C + 3°C. "C" suffix denotes a + 2%
tolerance and "D" suffix denotes a + 1% tolerance.
Zener impedance is derived by superimposing on 1ZT A 60Hz rms a.c. current equal to
10% of IZT.
FIGURE 1
DESIGN DATA
CASE: DO-213AA, Hermetically sealed
glass case. (MELF, SOD-80, LL34)
THERMAL IMPEDANCE: (ZJX): 35
°C/W maximum
POLARITY: Diode to be operated with
the banded (cathode) end positive.
MOUNTING SURFACE SELECTION:
The Axial Coefficient of Expansion
(COE) Of this Device is Approximately
+6PPM/°C. The COE of the Mounting
Surface System Should Be Selected To
Provide A Suitable Match With This
Device.
6 LAKE STREET, LAWRENCE, MASSACHUSETTS 01841
PHONE (978) 620-2600
FAX (978) 689-0803
WEBSITE: http://www.microsemi.com
123
CDLL4614 thru CDLL4627
FIGURE 2
Pd, Rated Power
Dissipation (mW)
500
400
300
200
100
0
0
25
50
75
100
125
150
175
TEC , End cap temperature (°C)
POWER DERATING CURVE
1000
500
400
300
3.3 VOLT
ZENER IMPEDANCE ZZT (OHMS)
200
100
5.1 VOLT
50
40
30
20
10
5
4
6.2 VOLT
3
2
1
.1
.2
.5
1
2
5
10
20
50
100
OPERATING CURRENT IZT (mA)
FIGURE 3
ZENER IMPEDANCE VS. OPERATING CURRENT
124
Similar pages