NKK JWL11RA1 Internationally approved tv rated rocker Datasheet

Internationally Approved TV Rated Rockers
Series JW
Distinctive Characteristics
Industry’s first molded rocker with TV rating. Designed to
handle large inrush current. JWM models certified for TV-5
rating and JWL models for TV-8 rating.
Special 5A @ 72V DC rating for JWL models to use
in worldwide telecommunication equipment for
power distribution applications.
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Constructed for dust resistance with interior
cover between actuator and contact area.
Specially designed to break light contact welds.
JWMW panel seal version meets IP67 of IEC60529
Standards (similar to NEMA 4 and 6).
Terminals are molded in and epoxy sealed to lock out flux, dust,
and other contaminants.
Actual Size JWM
Housing and case of heat resistant resin meet UL 94V-0
standard.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Internationally Approved TV Rated Rockers
Series JW
General Specifications
Electrical Capacity (Resistive Load)
Power Level:
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Angle of Throw:
Materials & Finishes
Housing/Frame & Barrier:
Interior Seal for JWM & JWL:
Case/Base:
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
Sealing:
Installation
Soldering Time & Temp:
Standards & Certifications
Flammability Standards:
TV Ratings for UL & CSA:
UL File No. WOYR2.E44145
CSA File No. 023535-0-000
UL & C-UL Recognized:
R
CSA Certified:
VDE Approved:
V
D E
10A @ 125/250V AC for JWM & JWMW models; 10A @ 30V DC for JWMW;
16A @ 125/250V AC for JWL models; 5A @ 72V DC for telecommunication applications
10 milliohms maximum for JWM & JWMW; 20 milliohms maximum for JWL
1,000 megohms minimum @ 500V DC
2,000V AC minimum between contacts for 1 minute minimum;
4,000V AC minimum between contacts & case for 1 minute minimum
25,000 operations minimum
25,000 operations minimum
JWM & JWMW Single Pole 3.92N & Double Pole 7.84N
JWL Single Pole 5.00N & Double Pole 10.00N
26°
Polyamide (UL94V-0)
Polyphenylene sulfide
Melamine (UL94V-0)
Movable Contacts:
Stationary Contacts:
Terminals:
Silver alloy
Silver alloy
Brass with silver plating
–25°C through +70°C (–13°F through +158°F) for JWM & JWL;
–25°C through +85°C (–13°F through +185°F) for panel seal JWMW model
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
IP67 of IEC60529 standard for panel seal JWMW model; dust resistant inner seal for others.
Manual Soldering: See Profile A in Supplement section.
UL94V-0 for housing/frame & case/base of JWL, JWM, & JWMW models
JWM & JWMW (TV-5) Overload Test @ 120V AC for 50 operations:
Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A
JWM & JWMW (TV-5) Endurance Test @ 120V AC for 25,000 operations:
Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A
JWL (TV-8) Overload Test @ 120V AC for 50 operations:
Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A
JWL (TV-8) Endurance Test @ 120V AC for 25,000 operations:
Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A
JWM & JWMW models recognized at 10A @ 250V AC & JWMW at 10A @ 30V DC;
JWL models recognized at 16A @ 250V AC; 5A @ 72V DC (specify “/U-DC” after part
number to request UL rating be marked on DC rated switches);
UL File No. WOYR2.E44145; C-UL File No. WOYR8.E44145.
JWM & JWMW models certified at 10A @ 250V AC;
JWL models certified at 16A @ 250V AC; CSA File No. 023535-0-000
JWM models approved at steady state 5A, inrush 80A, resistive 10A, &
motor load 6A all at 250V AC; VDE License No. 115637; JWL models approved at steady state 8A,
inrush 128A, resistive 16A, & motor load 8A all at 250V AC; VDE License No. 115637.
Note: JWM & JWL Double Pole, Single Throw models approved only with the
international on-off symbols on the actuator.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series JW
Internationally Approved TV Rated Rockers
TYPICAL SWITCH ORDERING EXAMPLE
JW
L
2
1
RATINGS
R
C
2
BARRIER TYPES
M
TV-5 Rated
10A @ 125/250V AC
MW
Panel Seal TV-5 Rated
10A @ 125/250V AC
L
TV-8 Rated
16A @ 125/250V AC
A
HOUSING COLORS
R
No Barrier
A
Black
B
With Barrier
B
Ivory
Note: JWMW combines
with code R only.
H
Gray
Note: JWMW available with black only.
CAP COLORS
POLES
A
Black
BARRIER COLORS
1
SPST
SPDT
B
Ivory
A
Black
C
Red
B
Ivory
2
* DPST
DPDT
H
Gray
H
Gray
* DPST must have international ON-OFF symbols
for VDE approval.
Note: JWMW available
with black or red only.
INSCRIPTION
ORIENTATION
CIRCUITS
1
ON
NONE
OFF
No
Code
2
ON
NONE
ON
1
Horizontal
2
Vertical
No Inscription
IMPORTANT:
Standard markings: TV Rating, UL,
C-UL, CSA, & VDE.
Specific models & ratings for
international approvals noted on
General Specifications page.
These are inscriptions for
Single Throw models only.
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
JWL21RC2A
Red Rocker Cap
with International ON-OFF Symbols
in Vertical Orientation
DPST
ON-NONE-OFF Circuit
Black Housing
TV-8 Rated
16A @ 125/250V AC
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series JW
Internationally Approved TV Rated Rockers
RATINGS
M
TV-5 Rated
Power Level
10A @ 125/250V AC
MW
Panel Seal TV-5 Rated
Power Level
10A @ 125/250V AC
TV-8 Rated
Power Level
16A @ 125/250V AC
L
POLES & CIRCUITS
Rocker Position
Connected Terminals
Down
Center
Up
Down
Center
Up
Throw & Schematics
Note: Terminal numbers are not actually
on the switch. Actuator positions oriented
with switch part number facing front.
Pole
Model
SP
JWM11
JWMW11
JWL11
ON
NONE
OFF
1-1b
OPEN
OPEN
SPST
SP
JWM12
JWMW12
JWL12
ON
NONE
ON
1-1b
OPEN
1-1a
SPDT
DP
JWM21
JWMW21
JWL21
ON
NONE
OFF
1-1b
2-2b
OPEN
OPEN
DPST
DP
JWM22
JWMW22
JWL22
ON
NONE
ON
1-1b
2-2b
OPEN
1-1a
2-2a
DPDT
1 (COM)
1b
1 (COM)
1a
1
1b
(COM)
2
1b
1
1a
2b
(COM)
1b
2
2a
2b
BARRIER TYPES & COLORS
R
B
No Barrier
Flange/Housing Material: Polyamide
Finish: Matte
JWM
With Barrier
Barrier Material: Polyamide
Finish: Matte
JWL
No-barrier type has a flat flange
which is an integral part of the switch.
JWMW panel seal device has exterior seal of acrylonitrile
butadiene rubber covering the flange.
JWM
JWL
Barrier type designates that either AT217 (for JWM) or
AT218 (for JWL) is factory assembled.
Dimensions for barriers are shown in the Accessories section.
Barrier Colors
Available:
A
Black
B
Ivory
H
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
Gray
03-07
Series JW
Internationally Approved TV Rated Rockers
CAP COLORS
Rocker cap is an integral part of the switch and not available separately.
JWMW available with black or red caps only.
Cap Material:
Polyphenelene Oxide
Finish: Matte
Cap Colors
Available:
A
Black
B
C
Ivory
H
Red
Gray
INSCRIPTIONS
No Code
1
No Inscription
DPST models without inscriptions
do not have VDE approval.
Inscription for
Horizontal Mounting
Inscription for
Vertical Mounting
2
The IEC symbols for On-Off are supplied with Single Throw models only.
Orientation of inscription must be selected.
Inscription Colors: Black ink on Ivory or Gray cap. White ink on Black or Red cap.
Contact factory for other inscriptions.
HOUSING
Material: Polyamide
A
Colors Available:
Black
B
Ivory
H
Gray
Finish: Matte
JWMW panel seal models available in black housing only.
TERMINALS
Solder Lug/.110” (2.8mm) Quick Connect
Solder Lug/.187” (4.75mm) Quick Connect
JWM & JWMW
JWL
Epoxy Seal
(3.2)
.126 (7.5)
.295
(0.6) R
(2.8)
.024
.110
(1.6)
.063
Thk = (0.5)
.020
Epoxy Seal
(7.5)
.295
(1.5) R
.059
(0.65) R
.026
Thk = (0.8)
.031
(4.75)
.187
This switch assembly with connectors is not UL, C-UL, CSA, or VDE approved.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Internationally Approved TV Rated Rockers
Series JW
TYPICAL SWITCH DIMENSIONS
TV-5 No Barrier • 10 Amp
Single & Double Pole
(15.0)
.591
(6.0)
.236
Part No.
(19.6)
.772
(7.7) Typ
.303 (22.6)
.890
26°
2b
JWM11RC1A
TV-5 With Barrier • 10 Amp
1
COM
(16.4)
.646
(0.5) Typ
.020
(21.5)
.846
1a
Single & Double Pole
(15.0)
.591
Part No.
(7.7) Typ
.303
(22.6)
.890
(25.0)
.984
(19.6)
.772
2b
1b
2
1
COM
COM
(0.5) Typ
.020
(13.6)
.535 (18.0)
.709
(22.2)
.874
Panel Seal • TV-5 No Barrier • 10 Amp
(7.2)
.283
(2.8) Typ
.110
(6.2)
.244
(15.4)
.606
(7.5)
.295
(18.9)
.744
Single & Double Pole
(7.0)
.276
Part No.
(19.6)
.772
(15.0)
.591
(7.7) Typ
.303
(22.6)
.890
26°
2b
1b
2
1
COM
(16.4)
.646
COM
2a
(3.0)
.118
(13.6)
.535
(21.0)
.827
(21.5)
.846
(6.2)
.244
(15.4)
.606
(7.5)
.295
(29.6)
1.165
1a
(0.5) Typ
.020
JWMW22RCA
(30.0)
1.181
1a
2a
JWM11BCA-H
(2.8) Typ
.110
(6.2)
.244
(15.4)
.606
(7.5)
.295
(27.0)
1.063
COM
2a
(2.0)
.079
(13.6)
.535
(18.0)
.709
1b
2
(2.8) Typ
.110
Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a.
PANEL CUTOUTS FOR JWM MODELS
Panel Thickness Range
Without Barrier (JWM & JWMW):
.039” ~ .157” (1.0mm ~ 4.0mm)
With Barrier (JWM):
.024” ~ .126” (0.6mm ~ 3.2mm)
(25.0)
.984
(24.0)
.945
JWM
JWMW
(15.4)
.606
(15.4)
.606
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Internationally Approved TV Rated Rockers
Series JW
TYPICAL SWITCH DIMENSIONS
TV-8 No Barrier • 16 Amp
Single & Double Pole
(7.0)
.276
Part No.
(24.4)
.961
(20.0)
.787
(9.8) Typ
.386
(28.0)
1.102
26°
(20.2)
.795
2b
1b
2
1
COM
COM
2a
1a
(0.8) Typ
.031
(17.6)
.693
JWL21RC2A
(4.75) Typ
.187
(2.0)
.079
(23.0)
.906
(24.0)
.945
(9.0)
.354
(20.5)
.807
(7.5)
.295
Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a.
TV-8 With Barrier • 16 Amp
Single & Double Pole
(20.0)
.787
Part No.
(24.4)
.961
(9.8) Typ
.386
(28.0)
1.102
(29.0)
1.142
2b
1b
2
1
COM
COM
2a
(17.6)
.693
(23.0)
.906
(27.2)
1.071
JWL11BCA-H
(32.0)
1.260
(0.8) Typ
.031
(8.15)
.321
(21.4)
.843
1a
(9.0)
.354
(20.5)
.807
(7.5)
.295
(35.0)
1.378
(4.75) Typ
.187
Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a.
PANEL CUTOUT FOR JWL MODELS
Panel Thickness Range
Without Barrier:
.039” ~ .157” (1.0mm ~ 4.0mm)
(29.5)
1.161
With Barrier:
.024” ~ .126” (0.6mm ~ 3.2mm)
(20.5)
.807
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Internationally Approved TV Rated Rockers
Series JW
OPTIONAL DUST COVER
AT4126
Dust Cover for JWL Rocker
Lid: Clear Polyvinyl Chloride
Base: Black Polyamide
Recommended Temperature Range:
–10° ~ +70°C (+14°F ~ +158°F)
Loses pliability below 0°C (+32°F)
Recommended Panel Thickness:
.031” ~ .134” (0.8mm ~ 3.4mm)
(42.0)
1.654
(22.2)
.874
Top
(8.6)
.339
Side
(2.6)
.102
(33.0)
1.299
Bottom
Switch
Groove
Assembly Instructions:
(1) Insert bottom of switch through the base until
the tabs lock into place.
Lid
Base
(2) Snap the switch into the panel.
(3) Seat the lid into the grooves of the base.
Groove
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Similar pages